ADG 750
Download from Www.Somanuals.com. All Manuals Search And Download.
When using your dishwasher, follow the precautions listed below:
This appliance must be grounded. In the event of a
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.
malfunction or breakdown, grounding will reduce
the risk of anelectric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipment-
grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Keep children away from detergent and rinse aid, keep
children away from the open door of the dishwasher,
there could still be some detergent left inside.
This appliance is not intended for use by persons
(including children )with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Children should be supervised to ensure that they do
not play with the appliance.
Dishwasher detergents are strongly alkaline, they
can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
Do not place any heavy objects on or stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely
to damage the door seal;
2) Warning: Knives and other utensils with
sharp points must be loaded in the basket
with their points down or placed in a
horizontal position.
When using your dishwasher, you should
prevent plastic items from coming into contact
with the heating element.(This instruction is only
applicable to machines with a visual heating
element.)
Check that the detergent comparment is empty
after completion of the wash cycle.
The door should not be left open,
since this could increase the risk of tripping.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
Do not tamper with controls.
The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
n
ot so marked, check the manufacturer's
recommendations.
should not be reused.
The maximum number of place settings to be
washed is 9.
The maximum permissible inlet water pressure is
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international abbreviations:
PE
for polyethylene, e.g. sheet wrapping material
for polystyrene, e.g. padding material
polyoxymethylene, e.g. plastic clips
PS
POM
PP
polypropylene, e.g. Salt filler
ABS
Acrylonitrile Butadiene Styrene, e.g. Control Panel .
WARNING!
„
„
Packaging material could be dangerous for children!
For disposing of package and the appliance please go to a recycling centre. Therefore cut
off the power supply cable and make the door closing device unusable.
Cardboard packaging is manufactured from recycled paper and should be disposed in the
waste paper collection for recycling.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product.
„
„
„
For more detailed information about recycling of this product, please contact your local
city office and your household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
Control Panel
5
7
6
4
2
3
3in1 indicator light / 3in1
function button: To select and show 3in1 .
Program indicator lights and button: To select
one of the seven and show the washing program.
4
5
Start and reset button: To start the selected washing
program or reset the washing program when the
machine is working.
Display window: Program remaining time, delay time,
running indicator, temperature of water, Error codes, etc.
2
3
Delayed Start Button: To preset the wash timer and delay
the starting time up to 24 hours. Every press of this button
increases the time by 60 minutes.
Salt and rinse aid warning lights: To show
when the salt container or dispenser need to be
refilled
6
7
Power indicator light and switch: To turn on/off
and show the power supply.
Dishwasher Features
Back View
Front view
7
1
2
3
8
9
4
5
11
12
13
10
6
Upper Basket
Spray Arms
Main Filter
Coarse Filter
Tray ass
5
6
7
8
1
2
3
4
9
13
Rinse Aid Dispenser
Detergent Dispenser
Cup Shelf
10
11
12
Drain pipe connector
Inlet pipe connector
Lower Basket
Salt Container
Cutlery Basket
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using your dishwasher for the first time:
A. Set the water softener
B. Pour 1
／2 litre of water inside the salt container and then fill with dishwasher salt
C. Fill the rinse aid dispenser
D. Fill in detergent
A. Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have
a detrimental or adverse effect on the operation of the appliance. The higher the
content of these minerals and salts, the harder your water is. The softener should be
adjusted according to the hardness of the water in your area. Your local Water Authority
can advise you on the hardness of the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness of
the water used. This is intended to optimise and customise the level o f salt consumption.
Please follow the steps below for adjustment in salt consumption.
1. Unscrew the cap from the salt container.
2. There is a ring on the container with an arrow on it (see figure
on the side), if necessary, rotate the ring in the anticlockwise
direction from the "-" Setting toward the "+" sign, based on the
hardness of the water being used.
It is recommended that adjustments should be made in
accordance with the following scheme:
WATER HARDNESS
Salt consumption
(gram/cycle)
Auto nomy
(cycles/1kgs)
Selector Position
mmol/l
dH
Clarke
fH
0~8
0~14
0~10
10~28
28~56
56~75
0~1.4
1.4~3.9
3.9~8
8~11
0
/
/
-
8~22
22~45
45~60
14~39
39~80
80~107
20
40
60
50
25
16
Mid
+
°
°
°
dH=1.25
Clarke=1.78 fH=0.178mmol/l
"/"
No salt need added
"-"
Setting toward the"-" sign
Setting toward the"+" sign
DH: German degree
°
"+"
fH:
French degree
°
Setting toward between
the "-" sign and "+" sign
"Mid"
Clark: British degree
°
Contact your local water board for information on the hardness of your water supply.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Loading the Salt Into the Softener
Always use the salt intended for use with dishwasher.
The salt container is located beneath the lower basket and should be filled as explained in the
following:
Attention!
Only use salt specifically designed for the use in dishwashers! Every other type of
salt not specifically designed for the use in a dishwasher, especially table salt, will
damage the water softener. In case of damages caused by the use of unsuitable
salt the manufacturer does not give any warranty nor is liable for any damages caused.
Only fill with salt just before starting one of the complete washing programs.
This will prevent any grains of salt or salty water, which may have been spilled,
remaining on the bottom of the machine for any period of time, which may cause
corrosion.
A
B
C
Remove the lower basket and then unscrew and remove the cap from the salt container.
Before the first wash, fill 1lt. of water in the salt container of your machine.
Place the end of the funnel (supplied) into the hole and introduce about 1kg of salt.
It is normal for a small amount of water to come out of the salt container.
After filling the container , screw the cap tightly back clockwise.
D
E
Usually, the salt warning light will stop being illuminated within 2-6 days after the salt container has been filled with
salt.
F
Immediately after filling the salt into the salt container, a washing program should be started (We suggest to use the
soak or rapid program). Otherwise the filter system, pump or other important parts of the machine may be damaged
by salty water. This is out of warranty.
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well the salt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (for some Models),you can estimate when to fill
the salt into the softener by the cycles that the dishwasher has run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excessive salt.
C. Fill the Rinse Aid Dispenser
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can leave
spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is designed to
use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser. To fill the
dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black.
The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning light in the control panel, you can estimate the amount from the colour
of the optical level indicator"C "located next to the cap. When the rinse-aid container is full, the whole
indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let
the rinse aid level fall 1 / 4 full.
C (Rinse-Aid indicator)
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
6
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
1
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
2
3
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming
during the next wash. Don't forget to replace the cap before you close dishwasher door.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
Adjust lever
(Rinse)
set on "4". If spots and poor drying are a problem, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are show spots, adjust the dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.
D. Function of Detergent
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of the commercial quality detergents are suitable for this purpose.
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phosphate and without chlorine
3.Without phosphate and without chlorine
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Normally new pulverised detergent is without phosphate. Thus the water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 dH. If detergents without phosphate are used in the case of hard water
°
often white spots appear on dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not
be removed completely. In this case please choose a program with a higher temperature.
Concentrated Detergent
Based on their chemical composition, detergents can be split in two basic types:
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzymes
The use of
“
normal
”
washing programs in combination with concentrated detergents
reduces pollution and is good for your dishes; these wash programs are specifically matched
to the dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason
“normal”wash programs in which concentrated detergents are used can achieve the same
results that can otherwise only be achieved using
“
intensive
”
programs.
Detergent Tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programs. Therefore please use long programs when using detergent tablets, to
ensure the complete removal of detergent residuals.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than
Conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Always add the
detergent just before starting the dishwasher, otherwise it could get damp and will not
dissolve properly.
Amount of Detergent to Use
If the lid is closed: press release button. The lid will spring open.
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.
WARNING!
Dishwasher detergent is corrosive! Take care to keep it out of reach of children.
Proper Use of Detergent
Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser until you're ready to wash dishes.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Fill in Detergent
Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on the right:
6
The place of main wash cycle detergent placed ,
A
“MIN”means approximately 20g of detergent.
The place of pre-wash cycle detergent placed ,
approximately 5g of detergent
B
Please observe the manufacturers dosing and storage
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.
You find information about the amount of detergent for the single programme on the last page.
Please aware, that according to the level soiling and the specific hardness of water differences are possible.
Please observe the manufacturer's recommendations on the detergent packaging.
How To Use The 3IN1 Function
Your dishwasher has a 3in1 function which needs no salt and rinse aid but a 3In1 tablet.
This dishwasher comes with a 3in1 tablet container as an accessory.
Only the 3in1 function(for the program: intensive/Normal/Eco.) Can be used with 3in1 tablets.
If you use 3in1 tablets in other programs, the appliance will not achieve a good performance.
1. The figure below shows how to hang the 3in1 tablet container on the upper basket.
2. Rotate the upper sprayer and change the location of the container to ensure the upper sprayer is not
obstructed by the 3in 1 tablet container. Refer to the figure below for reference.
3. Put the 3in1 tablet into the container ,then start the 3in1 program.
When using 3in1 combination / compact Detergents ,please pay attention to make sure that
the size of the combination detergents fits to the dispenser
，so that combination
detergents can be easily put into the dispenser, and the dispenser would not be broken.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
For best performance of the dishwasher, follow these loading guidelines. Features and
appearance of baskets and cutlery baskets may vary from your model.
Attention before or after Loading the Dishwasher Baskets
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans.
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the baskets.
Loading the Upper Rack
The upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee
and tea cup and saucers, as well as plates, small bowls and shallow pans (as long as they are
not too dirty).
Position the dishes and cookware so that they do not get moved by the spray of water.
Bowl(M) Bowl(L) Cups
Gravy ladle
Glasses
Dessert plate Saucers
(Egg)
Front
Adjusting the Upper Basket
The height of the upper basket can be adjusted in order to create more space for large utensils
both for the upper/lower basket. The height of the upper basket can be adjusted by placing the
wheels on different height of the rails. Long items, serving cutlery, salad servers and knives
should be placed on the shelf so that they do not obstruct the rotation of the spray arms.
The shelf can be folded back or be removed when not required for use.
Upper wheels
Lower wheels
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Lower Basket
We recommend that you place large items which are most difficult to clean into the lower basket:
pots, pans, lids, serving dishes and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking
the rotation of the top spray arm.
Pots, serving bowls, etc. must always be placed top down.
Deep pots should be slanted to allow water to flow out.
The bottom basket feature fold down tine rows so that larger or more pots and pans can be loaded.
1. Cutlery basket
2. Dessert plates
3. Soup plates
4. Dinner plates
5. Oval platter
6. Saucer
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutlery Basket
Cutlery should be placed in the cutlery basket with the handles at the bottom. If the rack has side baskets, the
spoons should be loaded separately into the appropriate slots, especially long utensils should be placed in the
horizontal position at the front of the upper basket as shown in the picture.
3
1
3
5
5
5
5
5
5
3
1
3
1
2
3
4
5
6
7
3
1
3
5
5
2
5
6
1
3
1
3
1. Tea spoons
3
1
2
2
2
2
4
4
4
4
4
4
2. Dessert spoons
3. Soup spoons
4. Forks
5. Knives
6. Serving forks
7. Serving spoons
Do not leave any item extend through bottom.
Knives and other utensils with sharp points
must be loaded in the basket with their points
down or placed in an horizontal position.
2
1
7
2
2
2
1
1
7
4
4
4
Always load sharp utensils with the sharp
point down!
For washing in the dishwasher the following cutlery/dishes
Are not suitable
Are of limited suitability
Some types of glasses can become
dull after a large number of washes
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Silver and aluminum parts have a
tendency to discolour during washing
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Glazed patterns may fade if machine
washed frequently
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
NOTE:
Do not put in items that are dirty of cigarette ash, candle wax, lacquer or paint.
If you buy new dishes please make sure that they are suitable for dishwashers.
NOTE:
Please do not overload your dishwasher. There is only space for 9 standard dishes. Do not
use dish that is not suitable for dishwashers. This is important for good results and for
reasonable energy consume.
Loading cutlery and dishes
Before loading the dishes, you should:
Remove large left-over
Soften remnants of burnt food in pans
When loading the dishes and cutlery, please note:
Dishes and cutlery must not impede the rotation of the spray arms
Load hollow items such as cups, glasses, pans etc. with the opening downwards so that
water cannot collect in the container or a deep base
It is dangerous to open the door when washing, because the hot water may be scalded to you.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
(
)
Meaning: need to fill rinse into the Rinse-Aid Dispenser.
*En50242: This program is the test cycle, the rinse-aid dispenser
setting is recommended to be set to position 6.
Pre-wash（50℃）
For the heaviest soiled loads,
Pre-wash
Wash (60 ℃)
Rinse
Rinse
Rinse (70 ℃)
Drying
such as pots, pans, casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
5/22g
5/22g
173
171
1.4
18.4
13.0
Intensive
Pre-wash
Wash (50 ℃)
Rinse (60 ℃)
Drying
For normally soiled loads,
such as pots, plates,glasses
and lightly soiled pans.
Standard daily cycle.
0.81
Daily
EN 50242
Wash(45
Rinse (70
Drying
℃
℃
)
For dishes that need to be
rinsed and dried only.
)
98
8.0
0.8
0.7
Sani rinse
Eco.
Pre-wash
Wash (45
Rinse (60
Drying
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
℃
)
111
22g
11.0
℃)
A shorter wash for lightly
soiled loads that do not
need drying.
Wash (40 ℃)
Rinse (45 ℃)
15g
15g
28
0.35
7.0
Express
Delicate
Pre-wash
Wash (40 ℃)
Rinse (70 ℃)
Drying
For lightly soiled loads,
such as glasses, crystal and
fine china.
118
11
0.8
11.0
6.0
To rinse dishes that you
plan to wash later that day.
Pre-wash
0.01
Pre -wash
+
For the heaviest soiled loads,
such as pots, pans, casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
Pre-wash
Wash (70
Rinse
Rinse
Rinse (70
Drying
（60℃）
℃)
161
3in1
1.5
15.1
Intensive
+
℃)
3in1
Pre-wash
Wash (50
Rinse (70
Drying
For normally soiled loads,
such as pots, plates, glasses
and lightly soiled pans.
standard daily cycle.
+
℃
℃
)
)
148
128
3in1
3in1
1.0
0.8
Daily
+
3in1
12.7
12.7
+
Pre-wash
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
Wash (45
Rinse (70
Drying
℃
)
)
Eco.
+
℃
3in1
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On the Appliance
Starting a cycle wash
1
Draw out the lower and upper basket, load the dishes and push them back.
It is commended to load the lower basket first, then the upper one (see the section entitled
“Loading the Dishwasher”).
2
3
Pour in the detergent (see the section entitled“Salt, Detergent and Rinse Aid”).
Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification of the
socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
Close the door, press the ON/OFF button, and the ON/OFF light will turn on. Press the program
button to select a desired wash cycle, After 3 seconds, the machine will work.
4
Change the Program...
Premise:
1
A cycle that is underway can only be modified if it has only been running for a short
time. Otherwise, the detergent may have already been released, and the appliance may
have already drained the wash water. If this is the case, the detergent dispenser must
be refilled (see the section entitled " Loading the Detergent " ).
2
3
When you press the start/reset button more than 3 seconds, you can cancel the running
programme and select other programmes (see the section entitled " Starting a wash cycle. . . " ).
When you select Intensive/Normal/Eco.Programmes, you can select the 3in1 function.
If you open the door during a wash cycle , the machine will pause. When you close the door , the machine
will continue working after 10 seconds.
Forgot to Add a Dish?
A forgotten dish can be added at any time before the detergent cup opens.
Open the door a little to stop the washing.
Load the forgotten dishes.
3
4
1
2
After the spray arms stop working,you can open the door
completely.
Close the door, the dishwasher will start running again
after 10 seconds.
At the End of the Wash Cycle
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
The program has ended, only if there appears a 0 in the digital display (remaining program time).
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
It is dangerous to open the door when washing, because the hot water may scald you.
WARNING!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Filtering System
The filter prevents larger remnants of food or other objects from getting inside the pum.
The residues may block the filter, in this case they must be removed.
The filter system consists of a coarse filter,a flat (Main filter)
And a microfilter(Fine filter).
1
Main filter
Food and soil particles trapped in this filter are pulverized by a
2
special jet on the lower spray arm and washed down to drain.
Coarse filte2
1
Larger items, such as pieces of bones or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
3
filter and lift out.
3
Fine filter
This filter holds soil and food residues in the sump area and
prevents it from being redeposit on the dishes during wash cycle.
Filter assembly
The filter efficiently removes food particles from the wash water, allowing it to be recycled during the cycle.
For best performance and results, the filter must be cleaned regularly. For this reason, it is a good idea to
remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and
cup under running water. To remove the filter device, pull the cup handle in the upward direction.
The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
WARNING!
Step 1：Turn the filter in anti-clockwise direction,
then lift it up.
Step 2：lift the Main filter up
Step 3： lift the Fine filter up
When following this procedure from step1 to step 3, the filter system will be removed;
when following it from Step 3 to Step 1, the filter system will be installed.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remarks:
- Inspect the filters for blocking after every time the dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Remove any food remnants and
clean the filters under running water.
The entire filter assembly should be cleaned once a week.
Cleaning the Filter
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
on the last page and reinsert the entire assembly in the dishwasher, positioning it in its seat and pressing downwards.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of the dishwasher could be decreased.
WARNING!
Caring for the Dishwasher
The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning The Door
To clean the edge around the door, you should use only a soft warm, damp cloth.
To avoid penetration of water into the door lock and electrical components, do not
use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electrical components.
Abrasive agents or some paper towels should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on the dishwasher in winter. Every time after washing cycles,
please operate as follows
：
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe and water valve. (Use a pan to catch the water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
If your dishwasher cannot work because of the ice, please contact professional service persons.
Cleaning the Spray Arms
It is necessary to clean the spray arms regularly in order to
remove the accumulation of scale from the hard water
and thus prevent blocking of spray arm jets and bearings.
Unscrew
We Suggest to poke the blocked spray arm jets with a needle
to ensure good washing effect.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
When not in Use for a LongTime
After Every Wash
It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance.
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always
remove the plug from the socket.
Moving the Appliance
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
No Solvents or Abrasive Cleaning
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water an a little
vinegar, or a cleaning product made specifically for
dishwashers.
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Electrical Shock Hazard
Disconnect electrical power before
installing dishwasher.
The installation of the pipes
and electrical equipments
Failure to do so can result in death or
electrical shock.
should be done by professionals.
●
Installation preparation
The installation position of dishwasher should be near the existing inlet and drain hoses
and power cord.
One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of
the dishwasher.
Note: please check the accompanying installation accessories(hook for aesthetic panel
,screw)
Please carefully read the installation instruction.
●
Illustrations of cabinet dimensions and installation position of the dishwasher
Preparations should be made before moving the dishwasher to the installation place.
Choose a place near the sink to facilitate the installation of inlet and drain hoses (see figure 1).
If dishwasher is installed at the corner of the cabinet, there should be some space (illustrated in figure 2)
when the door is opened.
1
2
16
Download from Www.Somanuals.com. All Manuals Search And Download.
90 °
90 °
【Figure1】
820mm
Cabinet dimensions
Less than 5mm
between the top
of dishwasher and
cabinet and the
outer door aligned
to cabinet.
580mm
Electrical, drain and
water supply line
entrances
80
100
Space between cabinet
bottom and floor
450 mm
Dishwasher
【Figure2】
Cabinet
Minimum space when
the door is opened
Door of
dishwasher
Minimum space of 50mm
●
Aesthetic panel's dimensions and installation
1
The aesthetic wooden panel
could be processed according to the figure 3
Make a furniture door according to the diagram
and not to exceed 4 kg.
19 0
-0.5
The length of the panel should be within
the range of 537--587mm, not more
than 587mm.
【Figure3】
The aesthetic panel should
be processed in accordance
with the illustrated dimensions
(Unit: mm)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of
dishwasher(see figure 4a). After positioning of the panel , fix the panel onto the outer door by
screws and bolts(See figure 4b) .
【Figure4a】
Installation of aesthetic panel
2
2
1
1
【Figure4b】
Installation of aesthetic
wooden panel
ST4.5 screw
Cover
1. take away the cover
2. pin up the screw surely
3. get back the cover
Spacer for aesthetic panel
Note: Ensure that the screws
being used are not too long to
go through the furniture door.
Do not put additional screws
through the dishwasher door
into the furniture.
ST4.5 screw
Hook for aesthetic panel
Hook for aesthetic panel
Outer door of
dishwasher
Aesthetic panel
18
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Tension adjustment of the door spring
The door springs are set at the factory to the proper tension for the outer door. If aesthetic
wooden panel are installed, you will have to adjust the door spring tension. Rotate the
adjusting screw to drive the adjustor to strain or relax the steel cable(see figure 5).
Door spring tension is correct when
the door remains horizontal in the
fully opened positionLjyet rises
relax
to a close with the slight lift of a
finger.
【Figure5】
Tension adjustment
of the door spring
●
Connection of drain hoses
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it
run into the sink, making sure to avoid bending or crimping it. Use the special
plastic support that comes with the appliance (figure 6). The free and of the hose
must be at a height between 400 and 1000mm and must not be immersed in water
to avoid the back flow of it. ATTENTION: The special plastic hose support must be
solidly fastened to the wall to prevent the drain hose from moving and allowing water
to spill outside the drain.
【Figure6】
Drain pipe connection
19
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Dishwasher installation steps
1 Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer
to the template for positioning of the brackets.
2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to
tighten the left and right door springs. Failure to do this could cause damage to your dishwasher
(Illustration 2).
3 Connect the inlet hose to the cold water supply .
4 Connect the drain hose. Refer to diagram.(Figure 6)
5 Connect the power cord.
6 Affix the condensation strip under the work surface of cabinet. Please ensure the condensation
strip is flush with edge of work surface.
7 Place the dishwasher into position.
8 Level the dishwasher. The rear feet can be adjusted from the front of the dishwasher by turning
the screws on the left and right hand side of the cabinet (Illustration 5A). To adjust the front feet,
use a wrench and turn the front feet until the dishwasher is level (Illustration 5B).
9The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface-secure to the work surface by using two woodscrews ensuring the
dishwasher weight is not being hit by the surface (Illustration 6).
B. Marble or granite work top-secure the bracket to the side panel of the dishwasher and secure
the dishwasher to the furniture housing. Put the rubber cap over the screw (Illustration 7).
2
6
4
SCREW
CONE GEAR
5A
5B
5
RUBBER
COVER
7
SCREW
【Figure 7】
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Dishwasher must be level for proper dish rack operation and wash performance.
1
Place level on door and rack track inside the tub as shown to check that the
dishwasher is level.
2
level the dishwasher by adjusting the four leveling legs individually.
3
When level the dishwasher, please pay attention not to let the dishwasher tip over.
Check
【Figure 8】
Illustration of feet adjustment
Level
Front
to Back
NOTE:
The maximum adjustment
height of the feet is 60 mm.
Check level
side to side
For personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
WARNING!
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and burns.
This appliance must be earthed. In the event
of a malfunction or breakdown, earthing will
reduce the risk of electric shock by providing a
path of least resistance for the electric current.
This appliance is equipped with a cord having an
equipment-earthing conductor and an earthing
plug. The plug must be plugged into an appropriate
outlet that is installed and earthed in accordance
with all local standards and requirements.
„
Improper connection of the equipment-
grounding conductor can result in the risk
of an electric shock. Check with a qualified
electrician or service representative if you
are in doubt whether the appliance is
properly grounded. Do not modify the plug
provided with the appliance; If it is not fit
for the outlet. Have a proper outlet installed
by a qualified electrician.
„
21
Download from Www.Somanuals.com. All Manuals Search And Download.
In order to avoid that there is more water staying in the inlet hose,
please close the hydrant after using.(For the models: no safety inlet hose.)
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water inlet to be blocked and damage the appliance.
The water supply to the appliance can also be connected to the household hot water
line (such as, central system, heating system),as long as it does not exceed a
temperature of 60 C. In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as
described in the section for the connection to the cold water line.
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate proper installation.
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height of between 50 cm (minimum) and 100 cm (maximum)
from the bottom of the dish. The water drain hose should be fixed by a hose clip.
Start of Dishwasher
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2 The inlet valve is open
3 There is a leakage at the connections of the conducts
4 The wires are tightly connected
5 The power is switched on
6 The inlet and drain hoses are knotted
7 All packing materials and printings should be taken out from the dishwasher
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Calling for Service
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Error code:E1;
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
Technical
problems
Door of dishwasher
not properly closed.
Make sure to close the door properly and latch it.
Check drain hose.
Kink in drain hose
Filter clogged
Check coarse the filter
(see section titled " Cleaning The Filter ")
Kitchen sink clogged
Improper detergent
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Use only the special dishwasher detergent to avoid
suds. If this occurs, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then Start the "soak" wash
cycle to drain out the water . Repeat if necessary.
Always wipe up rinse-aid spills immediately.
Spilled rinse-aid
Detergent with
colourant was used
Make sure that the detergent is the one without
colourant.
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
General
problems
The affected items are
not corrosion resistant.
Always run the quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
A programme was not
run after dishwasher
salt was added.
Traces of salt have
gotten into the wash cycle.
The lid of the softer
is loose
Check the lip .Ensure the fix is fine.
A spray arm is
knocking against
an item in a basket
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Interrupt the programme,
and rearrange the items of crockery.
Items of crockery
are loose in the
wash cabinet
Noise
This may be caused
by on-site installation
or the cross-section of
the piping.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Items are blocking
Rearrange the items so that the spray can rotate freely.
the path of spray arms.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".
Unsatis
-factory
washing
result
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Aluminum utensils
have rubbed against
dishes.
Use a mild abrasive cleaner to eliminate those marks.
Dishes block
Re-loading the dishes properly.
detergent cups.
Improper loading
Too little rinse-aid
Load the dishwasher as suggested in the directions.
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Dishes are removed
too soon
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Unsatis
-factory
drying
result
Wrong program
has been selected
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
Use of cutlery with
a low-quality coating
Error Codes
When some malfunctions come on, the appliance will display error codes to warn you:
Tap is not opened, or water intake is restricted,or water pressure
is too low.
Longer inlet time.
Longer heating time,
but not reaching required temperature
Malfunction of temperature sensor or of heating element.
Overfilled.
Too mu ch i nlet w ater.
Failure of temperature sensor
Failure of temperature sensor
Open circuit or break of temperature sensor
Short circuit or break of temperature sensor
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Height :
820mm(adjustable+60mm)
445mm
Width :
Depth :
540mm
Voltage connected Load :
Water pressure:
Hot water connection :
Power supply:
Capacity:
see rating label
0.04-1.0MPa
max 60 ℃
see rating label
9 Place settings
25
Download from Www.Somanuals.com. All Manuals Search And Download.
|