DISHWASHER
ZDS 699 EX
UK
INSTRUCTION BOOKLET
152987 58/4
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house
and leave the appliance, always ensure that the book is left with the appliance in order that the new
owner can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of your safety. You MUST read it carefully before
installing or using the appliance.
G Do not sit or stand on the open door.
Installation
G Isolate the appliance from the power supply and
G This appliance is heavy. Care should be taken when
turn off the water supply after use.
moving it.
G Care should be taken when cleaning the bottom
G It is dangerous to alter the specifications or attempt
door seal and hinge area as any exposed metal
edges may cut if care is not taken.
to modify this product in any way.
G Care must be taken to ensure that the appliance
G This product should be serviced by an
does not stand on the electrical supply cable.
authorised Service engineer, and only genuine
spare parts should be used.
G Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
G Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local
Service Force Centre. Always insist on genuine
spare parts.
G Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Child Safety
Conservation
G This appliance is designed to be operated by
adults.
In the interest of the environment:
Children should not be allowed to tamper with the
controls or play with the product.
G Materials marked with the symbol
are
recyclable.
G Keep all packaging well away from children.
G Check with your local Council or Environmental
Health Office to see if there are facilities in your
area for re-cycling this appliance.
G Keep all detergents in a safe place out of children's
reach.
G When the appliance is to be scrapped, cut off
the power supply cable and make the door
closing device unusable to prevent young
children from being trapped inside.
During Use
G Items that are contaminated by petrol, paint, steel
or iron debris, corrosive, acidic or alkaline
G Help to keep your country tidy - use authorised
disposal sites for your old appliance.
chemicals must not be washed in this dishwasher.
G Under no circumstances should you open the door
whilst the appliance is in operation. Always turn off
the appliance before opening the door.
G Only use detergent specifically designed for use in
dishwashers.
G Long bladed knives stored in an upright position are
a potential hazard.
G Long and/or sharp items of cutlery such as carving
knives must be positioned horizontally in the upper
basket.
G When finishing loading or unloading close the
door, as an open door can be a hazard.
AVV01en
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the appliance
1. Levelling spacers
2. Upper basket stop
3. Upper spray arm
1
13
12
4. Salt container
2
5. Large filter
3
6. Detergent dispenser
7. Control panel
11
10
4
5
8. Rating plate
9. Rinse aid dispenser
10. Central filter
6
9
11. Lower spray arm
12. Upper basket
8
7
13. "SID" detergent dispenser
IN84
The control panel
1 2
3
4 5 6 7 8 9
10
1. On/Off indicator light
Water tap
Flashes when:
-
-
-
The water tap is closed.
The mains water supply has been cut off.
The inlet hose may be blocked.
2. On/Off push button
3. Indicator lights
Rinse aid
Open door
Illuminates when the rinse aid has run
out, to remind you to refill the rinse aid
dispenser.
Illuminates when the door has not been
properly closed.
Salt
4. Programme selection
push button
Illuminates when the salt has run out, to
remind you to refill the salt container.
For the setting of the wash programme refer
to the "Washing programmes" chart.
APP09en
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Half load push button
9. Programme start push button
By pressing this push button, washing can be
confined to a single basket.
This is the last push button to press after
having set the programme and closed the
door.
The indicator light corresponding to the selected
basket comes on and for some programmes the
prewash phase will be automatically excluded.
It starts the programme.
This option is useful and economical when only a
few dishes need washing.
10. Programme phase indicator lights
Remember to load all the dishes into the selected
basket.
Each phase is indicated with a symbol:
Prewash/Rinse and Hold
If both indicator lights are off, washing will be
carried out in both baskets.
Wash
Rinse
This option is not available with programmes 1
(Rinse and Hold) and 10 (Plate warmer).
Drying
As soon as you select a washing programme,
this illuminates all the phases the programme
consists of.
6. Eco drying push button
By pressing this push button you can opt to
shorten (ECO) or completely eliminate (NO) the
drying cycle, so making a considerable energy
saving.
As the programme progresses, the phase
under way will illuminate.
At the end of the programme the phase
indicator lights turn off.
The indicator light corresponding to the selection
will come on.
This option is not available with programmes 1
(Rinse and Hold) and 10 (Plate warmer).
If NO drying is selected the supply of rinse
aid is automatically excluded.
If both indicator lights are off, the full drying
cycle will be carried out.
7. Delay start push button
Allows the start of the programme to be delayed
by a minimum of 1 hour, up to 12 hours.
8. Digital display
APP10en
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Audible signals
Audible signals have been introduced to help
indicate which operations the dishwasher is
performing.
Short "instruction accepted" signal
When any of the push buttons are pressed, a short
audible signal informs you that the machine has
accepted the instruction given.
Long "programme run" signal
A continuous audible signal informs you that the
washing programme is starting.
Intermittent "end of programme" signal
An intermittent audible signal informs you that the
wash programme has ended.
"Alarm" intermittent signal
The machine is fitted with a number of alarm
systems to help you determine the cause of any
problems (see "Something not working").
An intermittent audible signal informs you that
an alarm is activated.
To deactivate these audible signals, press
simultaneously and keep pressed both HALF LOAD
and DELAY push buttons.
After about 3 seconds 3 short intermittent audible
signals inform you that the audible signals have been
deactivated.
SO263
To reactivate these audible signals, press
simultaneously and keep pressed both HALF LOAD
and DELAY push buttons.
After about 3 seconds 3 short intermittent audible
signals inform you that the audible signals have been
reactivated.
Both operations (to deactivate or
reactivate the audible signals) must be
carried out before starting a washing
programme; the setting will remain
memorised after switching off the
dishwasher.
APP08en
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections
comply with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and
then fill with salt
5. Fill the rinse aid dispenser.
Water hardness
6. Run a "Rinse and Hold" programme.
PPM
(Parts per
Million)
French
degrees
(°TH)
Clarke
degrees
Level
Setting the water softener
0 - 80
0 - 6
0 - 8
9 - 14
0
1
2
3
4
5
6
7
8
9
81 - 140
7 - 10
The dishwasher is equipped with a water softener
designed to remove minerals and salts from the water
supply, which would have a detrimental or adverse
effect on the operation of the appliance.
141 - 200
201 - 300
301 - 400
401 - 500
501 - 600
601 - 700
701 - 800
801 - 1200
11 - 14
15 - 21
22 - 28
29 - 35
36 - 42
43 - 49
50 - 56
57 - 84
15 - 20
21 - 30
31 - 40
41 - 50
51 - 60
61 - 70
71 - 80
81 - 120
The higher the content of these salts, the harder your
water is.
Water hardness is measured in equivalent scales,
Clarke degrees, French degrees and PPM (parts per
Million).
The softener should be adjusted according to the
hardness of the water in your area. Your local Water
Authority can advise you on the hardness of the water
in your area.
If your water is level 0 it is already soft
and therefore there is no need to use salt.
With the setting of the water softener at
level 0 the salt indicator light on the
control panel will always remain off.
Use salt from level 1 upwards.
The dishwasher is factory set at level 4.
If this level is not suitable for your area the softener
should be adjusted.
The adjustment of the water softener is
possible only with the machine in setting
mode.
To select a different level proceed as
follows:
1. Press SELECTION and DELAY push buttons
simultaneously for about 5 seconds. In the display
appears a "L" followed by a number which
corresponds to the current level.
2. Press within 5 seconds the DELAY push button as
many times as necessary until the required level
appears in the display. The level increases by 1
each time the button is pressed.
SO264
3. 5 seconds after this button has last been pressed,
the dishwasher memorises the level selected and
returns to the programme setting mode.
PDU04en
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling with salt
Only use salt specifically designed for use
in dishwashers.
All other types of salt not specifically
designed for use in a dishwasher, especially
table salt, will damage the water softener.
Only fill with salt just before starting one of
the complete washing programmes. This will
prevent any grains of salt or salty water,
which may have been spilled, remaining on
the bottom of the machine for any period of
time, which may cause corrosion.
To fill:
1. To fill with salt, unscrew the cap of the salt
container.
2. Pour 1 litre of water inside the container (this is
necessary only before filling with salt for the
first time).
3. Using the funnel provided, pour in the salt until the
container is full.
SALET
SAL
Do not worry if water over flows from the unit when
filling with salt, this is quite normal.
SALZ
SEL
4. Replace the cap making sure that there is no trace
of salt on the screw thread or on the gasket.
5. Screw on the cap tightly.
The salt container will require topping up periodically.
SR06
You are reminded of this by the salt indicator light on
the control panel which comes on when the salt has
finished.
The salt indicator light on the control panel
can remain illuminated for 2-6 hours after
the salt has been replenished, assuming the
dishwasher remains switched on. If you are
using salts that take longer to dissolve then
this can take longer. The function of the
machine is not affected.
SAL01en
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rinse aid
Rinse aid is automatically added during the last rinse,
ensuring thorough rinsing, and spot and streak free
drying. The dispenser, which is positioned inside the
door, holds about 110 ml of rinse aid, which is
sufficient for 16 - 40 dishwashing programmes,
depending upon the dosage setting.
Filling with rinse aid
1. Open the container by turning the lid (A)
anticlockwise.
2. Add the rinse aid until the container is completely
full. The indicator (B) will be completely dark.
A
3. Top up the rinse aid when the rinse aid indicator
BR01
light on the control panel illuminates.
Ensure that the lid is closed after every refill.
Do not put liquid detergent in the rinse aid
compartment. Clean up any rinse aid spilt during filling
with an absorbent cloth to avoid excess foaming
during the next wash.
B
5
4
6
1
Adjusting the dose
According to the finish and drying results obtained,
adjust the dose of rinse aid by means of the 6 position
selector (C) (position 1 minimum dosage, position 6
maximum dosage).
BR03
Start from position 3.
C
Gradually increase the dose if there are drops of water
or lime spots on the dishes after washing. Reduce it if
there are sticky whitish streaks on the dishes.
m
1
BR02
BRI02en
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your appliance
Loading your appliance
Before placing dishes in the machine, remove any
scraps of food, to avoid clogging the filters and
consequently reducing the performance.
Do not load very small items which can fall
through the baskets.
Open the door and slide out the baskets to load the
dishes.
UI48
The lower basket
The lower basket is designed to take saucepans, lids,
plates, salad bowls, cutlery etc.
Large dishes and lids should be arranged around the
edge of the basket, ensuring that the upper spray arm
can turn freely.
UI21
The two rear rows of prongs on the lower basket can
be easily lowered to allow you to load pots, pans and
bowls.
To lower the prongs:
- Slightly pull them upward and let them drop down
(see picture).
- To bring them back to the standing position, just pull
them up again.
CES24en
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The cutlery basket
Long bladed knives stored in an upright
position are a potential hazard.
These items should only be placed in the
removable knife basket.
Take care when loading or unloading sharp
items such as knives.
Removable knife basket
Long and/or sharp items of cutlery such as carving
knives must be placed horizontally in the removable
knife basket, which is positioned at the rear of the
upper basket.
UI53
Cutlery should be placed in the removable cutlery
basket with the handles facing downwards. If the
handles protrude from the bottom of the basket,
obstructing the lower spray arm, load the cutlery with
the handles facing upwards.
Ensure that cutlery is positioned in the compartments
and that soiled surfaces do not touch each other.
For best results use the cutlery grid/s inserts provided.
Mix spoons with other cutlery to prevent them from
sticking together.
Silver cutlery tends to go black if mixed with steel
cutlery. Place it in the cutlery basket separate from the
others.
UI63
The cutlery basket is in two parts which can be
separated to give greater loading flexibility.To
separate the two parts, slide them horizontally in
opposite directions and pull them apart.To
reassemble, reverse the procedure.
UI62
CES41en
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The upper basket
The upper basket is designed for plates (dessert
plates, saucers, dinner plates of up to 24 cm in
diameter), salad bowls, cups and glasses.
If dishese are loaded in the upper basket, tilt them
forwards.
Arrange items on and underneath the fold-down cup
racks so that water can reach all surfaces.
Light items (plastic bowls etc.) should be loaded in the
upper basket and arranged so they do not move.
US29
Before closing the door, ensure that the
spray arms can rotate freely.
US70
Adjusting the height of the upper
basket
If washing very large plates (over 27 cm and up to 31
cm in diameter) you can load them in the lower basket
after moving the upper basket to the higher position.
To move to the higher position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the
mechanism is engaged and the basket is stable.
When the top basket is in the higher
position it will only take plates up to 20 cm
in diameter and you will not be able to use
the raised cup racks.
RC04
To lower the basket to the original position
proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and the allow the
mechanism to drop back slowly, keeping hold of it.
Never lift or lower the basket on one side
only.
After loading your machine always close
the door, as an open door can be a hazard.
CES04en
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Use of detergent
Only use detergents specifically designed
for use in dishwashers.
We recommend the use of Finish detergents which
are available in the following options:
Finish Double Action Tablets. Each tablet has the
exact amount of detergent required, simply place in
the dispenser.
Finish Powder recommended for every day use.
Finish Liquid Gel ideal for every day use. As the gel
is extra gentle it is recommended for fine bone china.
Min = 15 g
Max = 30 g
D
If using powder detergents proceed as follows:
1. Open the dispenser lid by pulling the catch (D).
2. Add the detergent according to the recommended
quantity given in the "Washing programmes" chart.
As all detergents are not the same, you should also
consult the instructions from the manufacturer of
your brand.
X
I N
A
M
M
DE17
3. Always close the lid.
4. If the programme has a prewash add the required
detergent in the SID detergent dispenser, located
in the centre of the upper basket. (See "Washing
programmes" chart).
If using detergent in tablets proceed as follows:
1. For all programmes; place 1 tablet inside the
detergent dispenser.
DE14
2. Always close the lid.
3. For all programmes with prewash; place a portion
of a further tablet on the lid of the detergent
dispenser.
Insufficient quantities of detergent will
produce poor washing results, whereas an
excessive amount of detergent will not
improve washing results and is also
wasteful.
Using no more than the correct amount also
contributes to reducing pollution.
Compact detergents with enzymes
In these compact powders the environmentally unfriendly components have been replaced by natural enzymes
and other more biodegradable substances.
The enzymes deploy their full dirt dissolving power at a temperature as low as 50°C.
By choosing the "BIO" programmes you can therefore achieve the same cleaning results that would otherwise
be achievable only with 65°C programmes and conventional detergents.
These new compact powders are generally phosphate-free.
DET07UKen
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Hints and tips
To save energy
Items not suitable for
dishwashers
Place dishes in the machine immediately after every
meal and wait until the dishwasher is full before
washing.
The following items should not be washed in
the dishwasher (unless they are sold as
dishwasher proof):
If necessary run the Rinse and Hold programme (see
"Washing Programmes" chart) so that any food scraps
do not become caked on the dishes while you are
waiting to run the complete wash programme.
- Cutlery with wooden or horn handles or
glued parts
- bronze cutlery
Do not prewash dishes under running water.
- saucepans with wooden handles
- aluminium ware
Select an economic programme when dishes are not
very soiled, following the instructions given in the
"Washing programmes" chart.
- crystal ware
Select a drying option.
- leaded glass
Select the half load option if only a few dishes need
washing.
- plastic items
- antique or fine decorated china
Certain types of decoration can discolour when
washed in a dishwasher.
For best washing results
Crystal-ware and plastic objects, if not guaranteed
dishwasher proof should be washed by hand.
Before loading, remove all scraps of food and soak
very heavily soiled pots and pans.
Certain types of glass can also become opaque
after being washed several times in a dishwasher.
Arrange saucepans, cups and glasses etc. upside-
down.
A chemical reaction can occur between silver
cutlery and stainless steel cutlery. As a precaution,
do not wash together.
Tilt items with convex or concave surfaces so that the
water drains off easily.
Avoid contact between the dishes as far as possible.
Iron and cast iron objects can rust and stain other
items.
Aluminium tends to go black, copper, pewter and
brass tend to stain.
If in doubt check with manufacturer of
the item.
When buying new dishes, ensure that
they are dishwasher proof.
For best results we recommend the use of Finish detergents, rinse aid and salt.
P OURING
PACK
W
E
L
N
OUB
ION
T
C
E
A
D
L
I
Q
U
I
D
G
E
L
P
O
W
D
E
R
R
I
N
S
E
CONCENTRATED DISHWASHER DETERGENT
DE15
CON01UKen
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing programmes
Recommended quantity
of detergent
Degree of soil
and type of load
Programme
Cycle
description
wash
prewash
1 cold rinse
1.
Any.
(to avoid food scraps from
sticking together).
RINSE AND
HOLD
Partial load (to be completed
later in the day).
/
/
Hot prewash
Main wash up to 70°C
3 cold rinses
1 hot rinse
Turbo drying
Heavy soil.
Crockery, cutlery,
pots and pans
2.
INTENSIVE
70°C
25 g
25 g
25 g
25 g
10 g
10 g
5 g
Warm prewash
Main wash up to 65°C
2 cold rinses
1 hot rinse
Turbo drying
3.
Normal soil.
Crockery, cutlery,
pots and pans
NORMAL PLUS
65°C
WITH PREWASH
Cold prewash
Main wash up to 65°C
2 cold rinses
1 hot rinse
Turbo drying
4.
Normal soil.
Crockery and cutlery
NORMAL 65°C
WITH PREWASH
Cold prewash
Main wash up to 50°C
2 cold rinses
5.
Light soil.
Crockery and cutlery
ECONOMY 50°C
WITH PREWASH
5 g
1 hot rinse
Turbo drying
Cold prewash
Main wash up to 50°C
2 cold rinses
1 hot rinse
Turbo drying
6.
*
Normal soil.
Crockery and cutlery
BIO 50°C
WITH PREWASH
25 g
5 g
Main wash up to 50°C
1 cold rinse
1 hot rinse
7.
Light soil.
Crockery and cutlery
BIO 50°C
NO PREWASH
30 g
30 g
/
/
Turbo drying
Light soil.
Crockery and
party crockery
8.
Main wash up to 55°C
1 cold rinse
1 hot rinse
**
QUICK WASH
55°C
Cold prewash
Main wash up to 45°C
2 cold rinses
1 hot rinse
Turbo drying
9.
Light soil.
Delicate china
and glassware
DELICATE 45°C
WITH PREWASH
25 g
5 g
This is a programme designed
both to heat plates before
serving or remove dust from
dishes which have not been
used for a long time.
10.
/
/
1 hot rinse
PLATE WARMER
Testing programme for EN 50242 (see "Hints forTest Centres").
*
This is a special programme for quick washing a full load of lightly soiled dishes, glasses and crockery
(except pots) so that you may re-use them promptly.
**
Important! if you select the "half load" option remember to reduce the quantity of detergent.
PRO14en
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating sequence
1. Check the filters
8a. Setting and starting the
programme without "delay
start"
Ensure they are clean and properly positioned
(see "Maintenance and cleaning").
Press the "programme selector" push button
until the required programme number
appears in the digital display.
2. Press the On/Off push button
The display will show the last selected
programme and the corresponding phase
indicator lights will illuminate.
If the door is open also the "open door" indicator
light will illuminate.
The following options may also be
selected:
a-
b-
Half load by pressing the corresponding
push button.
Eco drying by pressing the corresponding
push button.
Press the START push button, an audible
signal advises you that the programme has
started.
3. Check that there is rinse aid
and salt
The corresponding indicator lights will illuminate
if refilling is necessary.
The display will show the running time
of the programme and the indicator lights of
the phases will turn off except for the
indicator light of the current phase.
The time in the digital display will start to
decrease from minute to minute.
4. Load the dishes
Remove any scraps of food.
Pressing the "programme selector"
push button while the programme is running
will display the number of the current
programme.
Pull the lower basket out and arrange the
saucepans, plates and cutlery in it.
Pull the upper basket out and arrange the
plates, saucers, glasses and cups etc. in it.
If the door is opened during the run of the
programme the current phase will be
interrupted and the digital display will show
the number of the programme. The indicator
light of the interrupted phase will start to
flash and the indicator light "open door" will
illuminate.
Slide the baskets back into the machine.
5. Ensure that the spray arms can
rotate freely.
Once the door is closed the programme will
start from the point where it was interrupted.
6. Measure out detergent
Add the required amount of detergent into the
dispenser.
Close the detergent dispenser lid.
7. Close the dishwasher door
SEQ06en
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Empty the lower basket first and then the
upper one; this will avoid water dripping
from the upper basket onto the dishes in
the lower one.
8b. Setting and starting the
programme with "delay start"
Once a programme and required options
have been selected to use DELAY
proceed as follows:
Press the DELAY push button. The
digital display will show "h 0". Press the
button again to select the number of hours
by which you wish to delay the programme
start (up to a maximum of 12 hours).
Important!
In general it is not advisable to open the
door while the machine is working; if the
door is opened however, a safety device
ensures that the machine stops.
Care must be taken if the door is opened
during the hot phase or immediately
after a programme has finished, as
steam may escape.
The delay start will not modify the settings
made previously .
To set the time setting to zero press the
DELAY push button until "h 0" appears
in the digital display.
Press the START pushbutton.
The digital display shows the delay time
required before the start of the programme.
When the washing programme has
finished, it is recommended that the
dishwasher is unplugged and the water
tap turned off.
The start of the countdown will be confirmed
by the flashing "h" in the digital display.
Once the delayed time has elapsed the
programme will start automatically.
9. To cancel a programme in
progress
Press the "START" pushbutton for 5
seconds to cancel the setting or the running
of the current programme.
All the indicator lights will turn off and 3
horizontal lines will appear in the digital
display.
After 5 seconds the dishwasher will return to
setting mode.
It is now possible to select a new washing
programme.
10. At the end of the washing
programme
The dishwasher will automatically stop and
an intermittent audible signal will sound
when the programme has ended.
3 flashing horizontal lines will appear in the
digital display and all the indicator lights will
turn off.
To return to setting mode press any of the
pushbuttons or switch off and then switch on
the dishwasher.
Open the door and wait a few minutes
before removing the dishes; in this way
they will be cooler and the drying will be
improved.
SEQ07en
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and cleaning
Internal cleaning
Ensure that the seals around the door, the detergent
and rinse aid dispensers are cleaned regularly with a
damp cloth.
We recommend the use of Finish Dishwasher Cleaner
every 3 months or run a 65°C wash without dishes
using detergent. Regular use of Finish Dishwasher
Cleaner cleans inaccessible parts, eliminates
unpleasant food odours and helps prevent the build-up
of limescale.
Cleaning the central filter
(After each wash)
Scraps of food may accumulate in the drain filter (A)
and should be removed by rinsing the filter under
running water.
To remove the drain filter
A
- simply pull it out by the handle.
Once cleaned, refit the filter by pushing it back to its
MA04
MA19
original position until it engages.
Cleaning the large filter
(Every week)
If necessary clean the large filter (B) on both sides
under running water, using a brush.
To remove the large filter
90°
1. Remove the spray arm by pulling it upwards on one
B
side.
C
2. Turn the column (C) anticlockwise by 90° and then
slide out the filter.
MA20
MA05
3. Once cleaned refit it following the above instructions
in reverse order.
4. Ensure the filter is in its original position, the handle
of the drain filter should be pointing towards the
front of the appliance.
MA21
MA18
The dishwasher must not be used without
filters.
Incorrect repositioning and fitting of the
filters will produce poor washing results.
Cleaning the filters is vital to ensure correct
operation of the machine.
MAN04UKen
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Check that the SID is not clogged with detergent
residue. If necessary rinse it under running water after
having removed it from the basket by twisting it
anticlockwise and pulling it upwards.
Fasten it back onto the support by turning it clockwise.
Never use your dishwasher without the SID
dispenser.
Since SID also ensures correct distribution
of the water to the upper spray arm, running
the dishwasher without it will impair the
washing results.
MA12
External cleaning
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If necessary use
only neutral detergents. Never use abrasive products,
scouring pads or solvent (acetone, trichloroethylene
etc....).
Prolonged periods of non-operation
If you are not using the machine for any period of
time you are advised to:
1. Unplug the appliance and then turn off the water.
2. Fill the rinse aid dispenser.
3. Leave the door ajar to prevent the formation of
any unpleasant smells.
4. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location where the
temperature is below 0°C. If this is unavoidable, empty
the machine, close the appliance door, disconnect the
water inlet pipe and empty it.
Moving the machine
If you have to move the machine (moving house
etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
MAN07en
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without
calling out an engineer.
The dishwasher is fitted with a number of alarm systems which can help you to quickly determine the cause of
any problems.
The dishwasher will not start or stops during operation, all push buttons are inoperative except for the On/Off
push button and all the indicator lights turn off. In the digital display one of the following flashing fault codes will
appear AL1, AL2, AL3, AL4, AL5, AL6, AL7, AL8 and an audible signal will inform you of the alarm intervention.
Press the On/Off pushbutton to switch off the dishwasher and carry out the following suggested corrective
actions listed below.
Once the checks have been carried out switch on the dishwasher and start a washing programme, if the fault
code reappears in the digital display, contact your local Service Force Centre.
Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or
installation a charge will be made if the appliance is in guarantee.
Symptom
Fault code
Solution
The machine will not start
G The door has not been properly closed. Indicator light
"open door" illuminates.
G The plug is not properly inserted in the power socket.
G There is a power failure.
The machine does not fill
with water
Indicator light
"water tap" flashes
and/or alarm AL5
G Ensure the water tap is open.
G Ensure the mains water supply has not been cut off.
G The inlet hose may be squashed or bent. Reposition the
hose.
G The inlet hose may be blocked. Switch off the water
supply and clean the filter.
The dishwasher will not drain
Alarm AL6
G The drain hose may be squashed or bent. Reposition the
hose.
G The sink may be blocked. Clear any blockages.
G The drain hose extension is not correct. Follow the
instructions for connecting to the waste.
G There is no vent in the end of the drain hose.
General
Alarms AL1, AL2,
AL3, AL4, AL7
AL8
G Switch off the dishwasher. Switch it back on and start the
programme. If the alarm reappears, call the local
Service Force Centre.
The machine is noisy
G Dishes are rattling against each other, refer to “Loading
your machine”.
G The spray arms are knocking against the dishes. Refer
to "Loading your machine".
The door is difficult to close
G The dishwasher is not level, or not properly built-in.
Visible lime deposits or
white film on the dishes
G Check that there is salt and that the salt cap is tight.
G Check that the right level of the water softener is setted.
The dishes are not quite dry
G The rinse aid has run out or too little is being used.
The dishes are not clean
(poor wash)
G The baskets are too full.
G The dishes have not been arranged properly.
G The spray arms do not rotate
G The spray arms are clogged.
G The filters are clogged.
G The filters are not in the correct position.
G Not enough detergent has been used or it is unsuitable.
G The detergent is old or has gone hard.
G The salt container cap is not properly closed.
G The washing programme selected is too gentle.
RIM09UKen
20
Download from Www.Somanuals.com. All Manuals Search And Download.
If after all these checks, the problem persists, contact
your local Service Force Centre, quoting the model
and serial number. This information can be found on
the rating plate located on the right hand side of the
dishwasher door (see picture).
Protection against flooding
The machine is fitted with a device in the bottom of the
machine to protect against flooding. The device will
operate if there are any water leaks in the machine,
however it will only operate if the machine is on.
Prod.No. ........ Ser. No. .........
Mod. ........
RA01
In case of intervention the digital display will show
"AL4". Turn off the water tap and call the Service
Force Centre.
Service and spare parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts please contact your
local Zanussi Service Force Centre by telephoning:
08705 929 929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
The addresses are listed on the following pages.
Before calling out an engineer, please ensure you
have read the details under the heading "Something
Not Working".
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number (found on the rating
plate)
5. The purchase date
Customer Care Department
For general enquiries concerning your Zanussi
appliance or for further information on Zanussi
products please contact our Customer Care
Department by letter or telephone at the address
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727 ( *)
* calls to this number may be recorded for training purposes
GAR04en
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
G The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
G The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
G The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us.
G All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
G Any appliance or defective part replaced shall become the Company’s property.
G This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
G Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
G Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
G Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
G Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
G The guarantee starts from the date you first purchased your product.
G The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
G This guarantee relates to you and cannot be transferred to another user.
G Your new home is within European Community (EC) or European Free Trade Area.
G The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
G The product is installed taking in account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Senlis
+33 (0) 44 62 29 99
+49 (0) 911 323 2600
Nurenberg
Pordenone +39 (0) 1678 47053
Sweden
UK
Stockholm
Slough
+46 (0) 8 738 79 50
+44 (0) 1753 219897
+353 (0) 14090753
Ireland
Dublin
GAR05en
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Zanussi Service Force
To contact your local Zanussi Service Centre telephone 08705 929 929
ORKNEY
(M65)
Corsie Domestics
7 King Street
Kirkwall
CHANNEL ISLANDS
NORTH EAST
GUERNSEY
Guernsey Electricity
PO Box 4
GATESHEAD
(M39)
Unit 356a
Dukesway Court
Orkney KW15
Vale, Guernsey
Channel Islands
Dukesway
Team Valley
Gateshead NE11 0BH
PERTH
Hydro Electrical
Inveralmond House
Ruthervenfield Road
Perth PH1 3AQ
JERSEY
Jersey Electricity Company
PO Box 45
Queens Road
St Helier
Jersey
GRIMSBY
(M42)
15 Hainton Avenue
Grimsby
South Humberside
DN32 9AS
PERTH
Graham Begg
Unit 4
Airport Ind Estate
Wick KW1 4QS
Channel Islands JE4 8NY
(OWN SALES)
SHETLAND
HULL
(M41)
Unit 1
Boulevard Industrial Estate
Hull
HU3 4AY
Tait Electronic Systems Ltd.
Holmsgarth Road
Lerwick
SCOTLAND
(OWN SALES)
SHETLAND
Shetland ZE1 0PW
ABERDEEN
(M05)
54 Claremont Street
Aberdeen AB10 6RA
LEEDS
(M37)
64-66 Cross Gates Road
Leeds
LS15 7NN
Bolts Shetland Ltd.
26 North Road
Lerwick
AUCHTERMUCHY
(M03)
33A Burnside
Auchtermuchy
Fife KY14 7AJ
NEWTON AYCLIFFE
(M45)
Unit 16
Gurney Way
Aycliffe Industrial Estate
Newton Aycliffe
DL5 6UJ
(OWN SALES)
WHALSAY
Shetland ZE1 0PE
Leask Electrical
Harlsdale
Symbister, Whalsay
Shetland ZE2 9AA
BLANTYRE
(M07)
Unit 5
Block 2
Auchenraith Ind Estate
Rosendale Way
Blantyre G72 0NJ
(OWN SALES)
SHEFFIELD
(M38)
Pennine House
Roman Ridge Ind.
Roman Ridge Road
Sheffield S9 1GB
DUMFRIES
(M01)
93 Irish Street
Dumfries
NORTHERN IRELAND
Scotland DG1 2 PQ
BELFAST
(M27)
Owenmore House
Kilwee Buisness Park
Upper Dunmury Lane
Belfast
NORTH WEST
DUNOON
(M67)
Brair Hill
7 Hill Street,
Dunoon
BIRKENHEAD
(M11)
1 Kelvin Park
Dock Road
Birkenhead
L41 1LT
BT17 0HD
Argyll PA23 7AL
GLASGOW
(M04)
20 Cunningham Road
Clyde Estate
WALES
Rutherglen,
GlasgowG73 1PP
CARLISLE
(M10)
Unit 7
CARDIFF
(M28)
Guardian Industrial Estate
Clydesmuir Road
Tremorfa
Cardiff
CF2 2QS
James Street Workshops
James Street
Carlisle
INVERNESS
(M06)
Unit 3B
Smithton Indust. Est.
Smithton
Cumbria CA2 5AH
Inverness IV1 AJ
ISLE OF MAN
(M64)
South Quay Ind Estate
Douglas
Isle of Man
CLYWD
(M14)
Unit 6-7 Coed - Parc
Abergele Road
Rhuddlan
Clwyd
Wales
ISLE OF ARRAN
Arran Domestics
Unit 4 The Douglas Centre
Brodick
IM1 5AT
(OWN SALES)
Isle of Arran KA27 8AJ
LIVERPOOL
(M15)
Unit 1
LL18 5UG
Honeys Green Precinct
Honeys Green Lane
Liverpool
ISLE OF BARRA
J Zerfah
244 Bruernish
Isle of Barra
DYFED
(M77)
Maes Y Coen
High Mead
Llanybydder
Carmarthenshire
SA40 9UL
L12 9JH
(OWN SALES)
ISLE OF BUTE
Western Islands HS9 5QY
MANCHESTER
(M09)
Unit B
Central Industrial Estate
St Marks Street
Bolton
Walker Engineering
Glenmhor
Upper Serpentine Road
Rothesay
HAVERFORDWEST
(M75)
Cromlech Lodge
Ambleston
Haverfordwest
Pembrokeshire
SA62 5DS
BL3 6NR
Isle of Bute PA20 9EH
PRESTON
(M13)
Unit 250
Dawson Place
Walton Summit
Bamber Bridge
Preston
ISLE OF LEWIS
(M69)
ND Macleod
16 James Street
Stornoway
OSWESTRY
(M17)
Plas Ffynnon
Warehouse
Middleton Road
Oswestry
Isle of Lewis PA87 2QW
Lancashire PR5 8AL
KELSO
(M08)
2-8 Wood Market
Kelso
Borders TD5 7AX
SY11 2PP
STOCKPORT
(M16)
Unit 20 Haigh Park
Haigh Avenue
Stockport
SK4 1QR
GAR22en
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Zanussi Service Force
To contact your local Zanussi Service Centre telephone 08705 929 929
MIDLANDS
LONDON & EAST ANGLIA
SOUTH EAST
BIRMINGHAM
(M18)
66 Birch Road East,
Wyrley Road Ind. Estate
Witton
Birmingham
B6 6DB
BECKENHAM
(M79)
11 a Gardener Ind. Estate
Kent House Lane
Beckenham
ASHFORD
(M58)
Unit 2
Bridge Road Buisness Est.
Bridge Road
Ashford
Kent BR3 1QZ
Kent TN2 1BB
CHELMSFORD
(M47)
Hanbury Road
Widford Ind. Estate
Chelmsford
Essex
BOURNE
(M44)
Manning Road Ind. Estate
Pinfold Road
Bourne
FLEET
(M59)
Unit 1
Redsfield Ind. Estate
Church Crookham
Fleet
PE10 9HT
CM12 3AE
Hampshire GU13 0RD
BRIDGNORTH
(M72)
68 St. Mary’s Street
Bridgnorth
Shropshire
COLINDALE
(M53)
Unit 14
Capitol Park
Capitol Way
Colindale
HAYWARDS
HEATH
(M55)
21-25 Bridge Road
Haywards Heath
Sussex RH16 1UA
WV16 4DR
London NW9 0EQ
GLOUCESTER
(M23)
101 Rycroft Street
Gloucester
GL1 4NB
ELTHAM
(M78)
194 Court Road
Mottingham
SOUTH WEST
Eltham
London SE9 4EW
BARNSTAPLE
(M30)
Main Box
Fremington
HEREFORD
(M31)
Unit 3
Bank Buildings
Cattle market
Hareford
Barnstaple
North Devon EX31 2NT
ENFIELD
(M49)
284 Alma Road
Enfield
HE4 9HX
London
EN3 7BB
BOURNEMOUTH
(M26)
63-65 Curzon Road
Bournemouth
Dorset
HIGHAM FERRERS
(M51)
30 High Street
Higham Ferrers
Northants
GRAVESEND
(M57)
Unit B4,
BH1 4PW
Imperial Buisness Estate
Gravesend
Kent
NN10 8BB
BRIDGEWATER
(M35)
6 Hamp Ind. Estate
Bridgewater
Somerset TA6 3NT
DA11 0DL
ILKESTON
(M43)
Unit 2
Furnace Road
Ilkeston DE7 5EP
HARPENDEN
(M46)
Unit 4
BRISTOL
(M25)
11 Eldon Way
Eldonwall Trading
Bristol
Riverside Estate
Coldharbour Lane
Harpenden
AL5 4UN
LEICESTER
(M22)
Unit 7
Oaks Ind. Estate
Coventry Road
Narborough
Leicestershire
LE0 5GF
Avon BS4 3QQ
EMSWORTH
(M33)
266 Main Road
Southbourne
Emsworth
LETCHWORTH
(M50)
16-17 Woodside Ind. Estate
Works Road
Letchworth
PO10 8JL
Herts
LINCOLN
(M40)
Unit 8
SG6 1LA
Stonefield Park
Clifton Street
Lincoln
ISLE OF WIGHT
(M34)
Unit 8
Enterprise Court
Ryde Buisness Park
Ryde
LONDON
(M76)
2/4 Royal Lane
Yiewsley
West Drayton
Middlesex
LN5 8AA
Isle of Wight PO33 1DB
NEWCASTLE
UNDER LYME
(M12)
18-21 Croft Road
Brampton Ind. Estate
Newcastle under Lyme
Staffordshire
UB7 8DL
NEWTON ABBOT
(M29)
Unit 2
Zealley Ind. Estate
Kingsteignton
Newton Abbot
S. Devon
MAIDENHEAD
(M60)
Reform Road
Maidenhead
Berkshire
ST5 0TW
SL6 8BY
REDDITCH
(M20)
13 Thornhill Road
North Moons Moat
Redditch
Worcestershire
B98 9ND
TQ12 3TD
MOLESEY
(M61)
10 Island Farm Avenue
West Molesey
Surrey
REDRUTH
(M36)
Unit 7D
Pool Ind. Estate
Wilson Way,
Redruth,
KT8 2UZ
TAMWORTH
(M19)
Unit 3
Cornwall TR15 3QW
Sterling Park
Claymore
Tamworth
B77 5DO
NEWBURY
(M24)
9 Pipers Court
Berkshire Drive
Thatcham
Berkshire
RG19 4ER
WORCESTER
(M73)
Units 1 & 2
Northbrook Close
Gregorys Mill Ind. Estate
Worcester
IPSWICH
(M48)
Unit 6C
Elton Park Business Centre
Hadleigh Road
Ipswich
WR3 8BP
IP2 0DD
NORWICH
(M52)
2b Trafalgar Street
Norwich
NR1 3HN
SUNBURY
(M63)
Unit 1 a
The Summit
Hanworth Road
Hanworth Ind Estate
Sunbury on Thames
TW16 5D
GAR23en
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Hints for test centres
Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse
aid dispenser.
Test standard
EN 50242
Reference programme:
Load:
Bio 50°C with prewash
12 standard place settings
position 5
Rinse aid selector:
Detergent dosage :
30 g in the dispenser
UI69
US66
UI48
Arrangement
cutlery basket
Arrangement
lower basket
Arrangement
upper basket
US67
Arrangement
knife basket
Technical specifications
DIMENSIONS
Width
59.6 cm
Height with worktop
Max depth
81.8 - 87.8 cm
59 cm
Max depth with open door
111.4 cm
ELECTRICAL CONNECTION
MOTOR RATING DURING WASH
POWER OF HEATING ELEMENT
OVERALL POWER
Voltage
220/240 V - 50 Hz
200 W
2100 W
2300 W
WATER SUPPLY PRESSURE
Minimum
Maximum
50 kPa (0.5 bar)
800 kPa (8 bar)
CAPACITY
12 place settings
IST22en
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation instructions
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
Remove all packaging before positioning the
machine.
If possible, position the machine next to a water tap
and a drain.
Water supply connections
The dishwasher may be fed with either hot (max.
60°C) or cold water.
Nevertheless we advise a cold water supply.
A hot water supply is not always efficient with very
soiled crockery as it shortens the washing
programmes.
Feeding the appliance with a hot water supply will
allow you to obtain considerably shorter programmes.
The water pressure must be within the limits given in
the technical specifications.
Your local Water Authority will advise you on the
average mains pressure in your area.
The dishwasher features fill and drain hoses which
can be turned either to the left or the right to suit the
installation.
The locknut must be correctly fitted to avoid water
leaks.
Avoid bends or kinks in the hose which could prevent
or slow down the water supply.
If the machine is connected to new pipes or pipes
which have not been used for a long time, you should
run the water for a few minutes before connecting the
inlet hose. This will prevent deposits of sand or rust
clogging the inlet hose filter.
COL11en
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Water outlet hose connection
The end of the drain hose can be connected in the
following ways:
1
2
1. To the sink outlet siphon, securing it if necessary
with a clip.
2. To a stand pipe provided with vent-hole, minimum
internal diameter 4 cm.
The waste connection must be at a height of between
30 cm (minimum) and 100 cm (maximum) from the
bottom of the dishwasher.
CS13
The drain hose can face either to the right or left of the
dishwasher
Ensure the hose is not bent or squashed as this could
prevent or slow down the discharge of water.
If you use a drain hose extension it must be no longer
than 2 metres and its internal diameter must be no
smaller than the diameter of the hose provided.
Likewise the internal diameter of the couplings used
for connections to the waste outlet must be no smaller
than the diameter of the hose provided.
The sink plug must not be in place when the
machine is draining as this could cause the water
to siphon back into the machine.
+ 2 m max
CS14
COL12en
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
This appliance must be earthed.
The manufacturer declines any
responsibility should this safety measure
not be observed.
If the plug that is fitted to your appliance is not suitable
for the socket, it must be cut off and the appropriate
plug fitted.
Important
The wires on the mains lead are coloured in
accordance with the following code:
Green
Blue
Brown
and
Yellow-Earth
-Neutral
-Live
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond with
the markings identifying the terminals in your plug.
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
"E" or the earth symbol
yellow.
or coloured green and
CE03
2. Connect the Blue (neutral) wire to the terminal in
the plug which is marked with the letter "N" or
coloured black.
3. Connect the Brown (live) wire to the terminal in the
plug which is marked with the letter "L" or coloured
red.
The plug moulded onto the lead incorporates a 13amp
BSI362 fuse. OnlyASTA or BSI fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the product.
A replacement cover/carrier must be obtained from
your local Service Force Centre.
This appliance complies with the following E.E.C.
Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and
subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility
Directive) and subsequent modifications.
COLUKen
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Building-in
This dishwasher is designed to be fitted under a
kitchen counter or worksurface.
It is essential that the recess dimensions indicated in
the diagram are followed.
No further openings for venting of the dishwasher are
required, but only to let the water fill and drain hose
and power supply cable pass through.
596
90
max
5
The recess height may be anywhere between 820 and
880 mm from the floor as the dishwasher incorporates
adjustable feet (max 60 mm).
600
A distance of 2 mm should be allowed between the top
of the dishwasher and the counter top.
-
+
II123
Adjusting the height of the
appliance
To adjust the height proceed as follows:
1. Loosen or tighten the two front feet.
2. The rear foot is adjusted by turning the screw in the
middle of the front kick plate to the left or right.
A pad is supplied for the rear foot to make sliding the
appliance in and out of the recess easier.
To fit the pad, press it onto the rear foot.
If required, the dimensions of this pads can be
reduced by breaking it where marked.
II52
Good levelling is essential for correct closure and
sealing of the door. When the appliance is correctly
levelled, the door will not catch on the levelling
spacers on either side of the cabinet.
If the door does not close correctly, loosen or tighten
the adjustable feet until the machine is perfectly level.
IN11
IN12
INS25UKen
29
Download from Www.Somanuals.com. All Manuals Search And Download.
The furniture door plinth
The door on this appliance is designed for the overlay
of a door plinth having the following dimensions:
Width:
596 mm
Height:
50 mm (min) - 120 mm (max)
20 mm max
Thickness:
The panel height should be no more than indicated,
otherwise complete opening of the door will no longer
be possible as the panel hits against the dishwasher
plinth.
II71
Mounting the infill panel
1. Drill the panel with a Ø 2 x 12 bit according to the
dimensions indicated in the figure.
2. Fix the panel to the cross bar provided with 2
screws 3.5 x 16.
458
3. Fix the cross bar to the dishwasher door with 2
screws 3.5 x 16 after having inserted the two hooks
of the cross bar on the lower section of the door.
II69
II70
Fixing to the adjacent units
To prevent the dishwasher tilting, it must be secured to
either the worktop or adjacent kitchen cabinet/wall
using the brackets supplied.
Insert the two fixing brackets into the slots provided in
the top front part of the dishwasher as shown in the
figure.
Secure the brackets to the adjacent units with the
3.5 x 16 screws using the upper or the side holes.
The appliance must be secured to the
underside of the worktop using the brackets
provided.
Failure to do this could cause damage or
injury.
II54
Attention!
The sides of the dishwasher must never be
drilled to prevent damage to hydraulic
components.
INS10en
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting the vapour protection
Fit the adhesive protection foil onto the front part of
the worktop; along the entire width.
II21
Noise protection
Adhesive noise protection ensures excellent noise
insulation. This should be fitted when the dishwasher
has been mounted in the recess and the height
adjusted.
Apply the protection as shown in the drawing, making
sure that the non-adhesive section reaches right down
to the floor.
II61
Kitchen plinth adjustment
To allow correct opening of the door it is sometimes
necessary to cut the kitchen plinth. Refer to the cutting
table.
According to dimensions (a) and (b) as shown on the
figure, you will find on the following table the depth (x)
of the cut to be made on the plinth.
a
b
II15
II111
The dimensions (a) and (b) of the table are those most
frequently used in the kitchen furnitures.
Height (a)*
170 160 150 140 130 120 110 100
136 131 125 118 110 100 93 85
135 131 125 118 110 102 92 85
137 132 125 118 110 102 94 85
138 134 128 120 110 104 95 85
90
75
75
75
75
78
80
85
40
50
60
70
X
80
/
/
/
139 130 124 115 105 98 88
90
/
/
138 129 120 110 100 90
100
/
135 125 115 105 95
600 mm
minimum
( ) dimensions in mm
*
X
Dimensions of the cut on the plinth
INS71en
31
Download from Www.Somanuals.com. All Manuals Search And Download.
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as
refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year
to a value of approx. 14 billion USD in more than 150 countries around the world.
©
Electrolux Household Appliances Limited 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
|