®
User’s manual
Accessory handset for
use with VTech models
LS6425/LS6426/
LS6475/LS6476
w w w.v techphones.com
Model: LS6405
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Parts checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in case it is necessary to ship your telephone for warranty service.
Battery
Battery
Handset
compartment cover
®
User’s manual
Accessory handset for
use with VTech models
LS6425/LS6426/
LS6475/LS6476
w w w.v techphones.com
Model: LS6405
Handset charger
and charger adapter
User’s manual
To purchase replacement batteries or power adapters, visit our website at
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Battery installation
Install the battery as shown below.
1. Plug the battery connector securely into the socket inside the handset battery
compartment, matching the color-coded label.
2. Place the battery with the label THIS SIDE UP facing up and the wires inside
the battery compartment.
3. Align the cover flat against the battery compartment, then slide it towards the
center of the handset until it clicks into place.
4. Charge the handset by placing it in the telephone base or charger. The
CHARGE light is on when the handset is charging.
1
2
3
4
CHARGE light
remains on
when charging.
•
•
If the handset will not be used for a long time, disconnect and remove the
battery to prevent possible leakage.
1 (800) 267-7377.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Battery charging
Once you have installed the battery, the screen indicates the battery status (see
the table below). If necessary, place the handset in the telephone base or charger
to charge the battery. For best performance, keep the handset in the telephone
base or charger when not in use. The battery is fully charged after 10 hours of
continuous charging. See the table on page 9 for battery operating times.
If the screen is blank or displays Place in charger, you need to charge the
handset without interruption for at least 30 minutes to give the handset enough
charge to use the telephone for a short time. When the battery is low, the
handset displays Low battery along with a flashing icon. If you are on a call in
low battery mode, the handset plays short beeps to alert you.
The following table summarizes the battery charge indicators and actions to take.
Battery indicators
Battery status
Action
The screen is blank, or
displays Place in charger
and flashes.
Battery has no or
very little charge. The
handset cannot be used.
Charge without interruption
(about 30 minutes).
The screen displays
Low battery and flashes.
Battery has enough
charge to be used for a
short time.
Charge without interruption
(about 30 minutes).
The screen displays
HANDSET X.
Battery is charged.
To keep the battery charged,
place it in the telephone base
or charger when not in use.
If you place the handset in the telephone base or charger without installing a
battery, the screen displays No battery.
After you install your telephone or power returns following a power outage, the
handset will prompt you to set the date and time. To skip setting the date and
time, press OFF/CANCEL.
SET DATE
MM/DD/YY
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Add and register a handset
You can add new handsets (LS6405, purchased separately) to your telephone
system. Each handset must be registered with the telephone base before use.
When first purchased, each handset displays Put HS on BASE to register. You
may need to charge the handset before registering it to the telephone base. For
more details on battery charging, see page 3.
To register a handset:
1. Make sure the handset is out of the telephone base
or handset charger and shows
Put HS on BASE to register and then place the
handset in the telephone base.
2. The handset displays Registering...Please wait and
the red IN USE light on the telephone base turns on. It
takes about 90 seconds to complete the registration
process. The handset displays
HANDSET X Registered (X represents the registered
handset number). The IN USE light turns off and the
handset beeps when registration completes.
If registration fails, the system will automatically try to
register again. If registration fails after the third try, the
handset displays Registration failed then
Put HS on BASE to register. This may take up to five
minutes to occur.
To reset the handset, remove it from the telephone base.
When the handset displays Put HS on BASE to register,
try the registration process again.
After registration, the date and time need to be reset.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Deregister handsets
If you want to replace a handset, or reassign the designated handset number of
a registered handset, you must deregister all handsets that are registered to the
telephone base. Then register each handset individually.
To make deregistration easier, read all of the instructions on this page before
you begin.
Make sure that all handsets are out of the telephone base and chargers before
you begin deregistration.
To deregister all handsets:
1. Press and hold /FIND HANDSET on the telephone base for about 10 seconds
until the IN USE light on the telephone base turns on and starts flashing.
2. Press and release /FIND HANDSET again. You must press /FIND HANDSET
while the IN USE light is still flashing. The IN USE light flashes for approximately
seven seconds.
3. The deregistration process takes about 10 seconds to complete. All handsets
show Put HS on BASE to register.
If deregistration fails, you may need to reset the telephone base and try again.
To reset:
•
Pick up the registered handset and then press /FLASH.
-OR-
•
Unplug the power from the telephone base, then plug it back in.
You cannot deregister all handsets if any other system handset is in use.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Handset layout
CHARGE light
On when the handset is charging in the telephone base
or charger.
/
/VOLUME (directory/volume)
Press to enter the directory when the telephone is
not in use.
While in a menu, press to scroll up.
During a call or message playback, press to increase
the listening volume.
When entering numbers or names in the directory,
press to move the cursor to the right.
MUTE/DELETE
While on a call, press to mute the microphone.
While reviewing the redial list, directory or caller ID log,
press to delete an individual entry.
While the handset is ringing, press to silence the ringer
temporarily.
While predialing, press to delete digits.
/FLASH
Press to make or answer a call.
During a call, press to answer an incoming call when you
receive a call waiting alert.
1
While reviewing a caller ID log entry, press repeatedly to
add or remove 1 in front of the telephone number before
dialing or saving it in the directory.
With the phone set for pulse dialing, press to temporarily
change to tone dialing while on a call.
/SPEAKER
Press to make or answer a call.
During a call, press to switch between the speakerphone
and the handset.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Handset layout
CID/ /VOLUME (caller ID/volume)
Press to review the caller ID log when the telephone
is not in use.
While in a menu, press to scroll down.
During a call or message playback, press to decrease
the listening volume.
When entering numbers or names in the directory,
press to move the cursor to the left.
MENU/SELECT
Press to show the menu.
While in a menu, press to choose an item, or save an
entry or setting.
OFF/CANCEL
During a call, press to hang up.
While the handset is ringing, press to silence the
ringer temporarily.
While the telephone is not in use, press and hold to
delete the missed call indicator.
While in a menu, press to go back to the previous menu.
While in a menu, press and hold to return to idle mode.
Dialing keys
Press to enter numbers or characters.
# (pound key)
Press repeatedly to show other dialing options when
reviewing a caller ID log entry.
When saving the caller ID log entries to the directory.
press to switch the name order.
EQ
During an outside call, intercom call, message or
announcement playback, press to change the audio
quality to best suit your hearing.
REDIAL/PAUSE
Press to review the redial list.
While predialing or entering numbers into the directory,
press and hold to insert a dialing pause.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Handset layout
PUSH TO TALK (PTT)
Press to begin a broadcast to
one or multiple handsets.
Press and hold to broadcast to
a group of handsets when the
handset is not in use.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Battery
It takes up to 10 hours for the battery to be fully charged. When it is fully charged, you can
expect the following performance:
Operation
Operating time
While in handset use (talking*)
While in speakerphone mode (talking*)
While not in use (standby**)
Up to seven hours
Up to five hours
Up to seven days
*Operating times vary depending on your actual use and the age of the battery.
**Handset is not charging or in use.
The battery needs charging when:
•
•
•
•
A new battery is installed in the handset.
The handset beeps.
A battery is properly installed and the screen is blank.
Low battery or Place in charger displays on the handset screen.
CAUTION:
To reduce the risk of fire or injury, read and follow these instructions:
•
Use only the battery(ies) provided or equivalent. To order a replacement, visit our
•
•
•
•
Do not dispose of the battery(ies) in a fire. Check with local waste management codes
for special disposal instructions.
Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.
Exercise care in handling batteries in order not to create a short circuit with conductive
materials.
Charge the battery(ies) provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
•
•
Observe proper polarity orientation between the battery and metallic contacts.
To prevent fire or shock hazard, do not expose this product to water or any type of moisture.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Slots and openings in the back or bottom of the telephone base and handset are provided for
ventilation. To protect them from overheating, these openings must not be blocked by placing the
product on a soft surface such as a bed, sofa or rug. This product should never be placed near
or over a radiator or heat register. This product should not be placed in any area where proper
ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply in your home or office, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
9. Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any
kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the telephone base or handset other than specified
access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can
cause electric shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords.
12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
• When the power supply cord or plug is damaged or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operation instructions. Improper adjustment of other controls
may result in damage and often requires extensive work by an authorized technician to restore the
product to normal operation.
• If the product has been dropped and the telephone base and/or handset has been damaged.
• If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of
electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances,
a spark may be created when the adapter is plugged into the power outlet, or when the handset is
replaced in its cradle. This is a common event associated with the closing of any electrical circuit.
The user should not plug the phone into a power outlet, and should not put a charged handset into
the cradle, if the phone is located in an environment containing concentrations of flammable or
flame-supporting gases, unless there is adequate ventilation. A spark in such an environment could
create a fire or explosion. Such environments might include: medical use of oxygen without adequate
ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
15. Only put the handset of your telephone next to your ear when it is in normal talk mode.
16. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs
are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
SAVE THESE INSTRUCTIONS
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary
evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers.
Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
•
Should keep wireless telephones at least six inches from the pacemaker.
•
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket,
when it is turned ON.
•
Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using
wireless telephones.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain
distance - which can vary with the locations of the telephone base and handset, the weather, and the
layout of your home or office.
When the handset is out of range, the handset screen displays Out of range OR No pwr at base.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect
well when you press /FLASH. Move closer to the telephone base, then press /FLASH to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To
improve reception, move closer to the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever
need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it
with wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own
safety, take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing
in the water. If the telephone base should fall into the water, DO NOT RETRIEVE IT UNTIL YOU
UNPLUG THE POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the
telephone by the unplugged cords.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
About cordless telephones
•
Privacy: The same features that make a cordless telephone convenient create some limitations.
Telephone calls are transmitted between the telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless telephone conversations could be intercepted by
radio receiving equipment within range of the cordless handset. For this reason, you should not think
of cordless telephone conversations as being as private as those on corded telephones.
•
•
Electrical power: The telephone base of this cordless telephone must be connected to a working
electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made
from the cordless handset if the telephone base is unplugged, switched off or if the electrical power
is interrupted.
Potential TV interference: Some cordless telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize or prevent such interference, do not place
the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is
experienced, moving the cordless telephone farther away from the TV or VCR often reduces or
eliminates the interference.
•
•
Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit
with conducting material such as rings, bracelets, and keys. The battery or conductor may overheat
and cause harm. Observe proper polarity between the battery and the battery charger.
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do
not burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could
release caustic material which could cause injury.
The RBRC® seal
The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is
voluntarily participating in an industry program to collect and recycle these batteries at the end of their
useful lives, when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-metal hydride batteries
into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized VTech product service centers. Please call
TM
1 (800) 8 BATTERY
for information on Ni-MH battery recycling and disposal bans/restrictions in your
area. VTech’s involvement in this program is part of its commitment to protecting our environment and
conserving natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device
under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended
to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Privacy of communications may not
be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander according to the intended usage of the product. This
product has been tested and found to comply with the FCC criteria. The handset may be safely held
against the ear of the user. The telephone base shall be installed and used such that parts of the user’s
body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by
the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network
must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a
single line and an RJ14 jack for two lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the
6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most,
but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact
your telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the connection of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone service
provider or a qualified installer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
FCC, ACTA and IC regulations
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has
been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its
authorized agents. For repair procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may
temporarily discontinue your telephone service. The telephone service provider is required to notify you
before interrupting service. If advance notice is not practical, you will be notified as soon as possible.
You will be given the opportunity to correct the problem and the telephone service provider is required
to inform you of your right to file a complaint with the FCC. Your telephone service provider may make
changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of
this product. The telephone service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada
technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of
the maximum number of devices allowed to be connected to a telephone interface. The termination on
an interface may consist of any combination of devices subject only to the requirement that the sum of
the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer”
or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from
defects in material and workmanship, pursuant to the following terms and conditions, when installed and
used normally and in accordance with the Product operating instructions. This limited warranty extends
only to the Consumer for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use
new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a
new or refurbished Product of the same or similar design. We will retain defective parts, modules, or
equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech
will return the repaired or replacement Products to you in working condition. You should expect the
repair or replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If
VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this
limited warranty also applies to repaired or replacement Product for a period of either (a) 90 days from
the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original
one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper
installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability,
or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers
have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America
or Canada, or used for commercial or institutional purposes (including but not limited to Products
used for rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of
systems outside the unit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Limited warranty
How do you get warranty service?
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls
and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and
transportation and are responsible for delivery or handling charges incurred in the transport of the
Product(s) to the service location. VTech will return repaired or replaced Product under this limited
warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage
or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of
purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you
authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and
return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location
along with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all
other written or oral communications related to this Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There
are no other express warranties. No one is authorized to make modifications to this limited warranty and
you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability
(an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of
purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental,
consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical specifications
Frequency Control
Transmit frequency
Crystal controlled PLL synthesizer
Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels
5
Nominal effective
range
Maximum power allowed by FCC and IC. Actual operating range may vary
according to environmental conditions at the time of use.
Power requirements
Handset: 2.4V Ni-MH battery
Handset charger: 6V AC @ 300mA
Memory
Handset directory: 50 memory locations; up to 30 digits and 15 characters
Handset caller ID log: 50 memory locations; up to 24 digits and 15 characters
17
Download from Www.Somanuals.com. All Manuals Search And Download.
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 97008.
Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W 1L5.
Copyright © 2011 for VTECH TELECOMMUNICATIONS LTD.
Printed in China.
91-004134-030-100
Download from Www.Somanuals.com. All Manuals Search And Download.
|
