User’s manual
Accessory handset
for use with
VTech model DS6151
w w w.v techphones.com
Model: DS6101
BC
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Appendix.............................................. 8
The RBRC® seal................................. 12
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Parts checklist
Your telephone contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Battery compartment cover
Battery
Belt clip
User’s manual
Charger and power adapter
Handset
To purchase a replacement battery or a power adapter, visit our website at
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Getting started
Battery installation
Install the battery as shown below.
1 Plug the battery connector
securely into the socket inside the
battery compartment, matching
the color-coded label.
2 Place the battery with the label
THIS SIDE UP and the wires
inside the battery compartment.
Slide the battery compartment
cover towards the center of the
handset until it clicks into place.
Charge the handset by placing it
in the telephone base.
3
4
CHARGE light remains
on when charging.
Battery.charging
Once you have installed the battery, the screen indicates the battery status
(see the table below).
•
For best performance, keep the handset in the telephone base or
charger when not in use.
The battery is fully charged after 16 hours of continuous charging.
If the handset will not be used for a long time, disconnect and
remove the battery to prevent any possible leakage.
•
•
Battery indicators
Battery status
Action
The screen is blank.
Battery has no charge and
the handset cannot be used.
Charge without interruption
(at least 30 minutes).
The screen shows
Battery has very little charge Charge without interruption
Place.handset.in.
and the handset cannot be
(at least 30 minutes).
charger.and flashes. used.
Battery has enough charge
to be used for a short time.
Charge without interruption
(at least 30 minutes).
The screen shows Low.
battery and flashes.
The screen shows
HANDSET.
Battery is charged.
To keep the battery charged,
place it in the telephone
base when not in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting started
Battery.charging
When.the.battery.is.fully.charged,.you.can.expect.the.following.performance:
Operation
Operating time
Up to 10 hours
Up to 7 hours
Up to 10 days
While in handset use (talking*)
While in speakerphone mode (talking*)
While not in use (standby**)
*Operating times vary depending on your actual use and the age of the battery.
**Handset is not charging or in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Getting started
Belt clip and optional headset
Belt clip
To attach the belt clip:
To remove the belt clip:
Snap the belt clip into
the slots on both sides
of the handset.
Gently lift either of the
belt clip tabs outwards to
remove the belt clip from
the handset.
Headset
For handsfree telephone conversation, you can use any industry standard
2.5mm headset (purchased separately). For best results, use a
VTech 2.5mm headset.
Lift the plastic cover.
Plug a 2.5mm headset
into the jack on the side
of the handset.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Getting started
Add and register a handset
Each newly purchased handset (DS6101) must be registered to the
telephone base (DS6151) before use. When first purchased, each
expansion handset shows Press [HOLD] on base for 4 sec, then press [#]
on handset. You may need to charge the handset before registering to the
telephone base. For more details on battery charging, see the table on
page 2.
To make registration easier, read all of the instructions on this page before
you begin.
To register a handset:
1. Place the unregistered handset in the telephone base. If Press [HOLD]
on base for 4 sec, then press [#] on handset does not appear on the
handset screen after a few seconds, remove the handset and place it in
the telephone base again.
2. Press and hold HOLD on the telephone base for about four seconds until
the telephone base displays Registering handset. While the handset
is still in the telephone base, press (pound key) on the handset. The
#
handset shows Registering... Please wait and it takes up to 60 seconds
to complete the registration. The handset and the telephone base show
HANDSET X Registered (X represents the handset number assigned)
and you hear a beep when the registration completes.
When the registration is complete, the newly registered handset is assigned
the next available handset registration number. For instance, if you already
have HANDSET, the next registered handset will be HANDSET 2. Then your
first handset will be renamed as HANDSET 1.
#
HOLD
• If the registration fails, the handset shows Registration failed. To reset the
handset, remove the handset from the telephone base and place it back in.
Try the registration process again.
• You cannot register a handset if any other system handset is in use.
• Only one handset can be registered at a time.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Getting started
Replace a handset
If you want to replace a handset or reassign the designated handset number
of a registered handset, you must deregister all the handsets and then
individually register each handset.
To make deregistration easier, read all of the instructions on this page before
you begin.
To deregister all handsets:
1. Remove any handset from the telephone base. Press and hold HOLD on
the telephone base for about 10 seconds until the telephone base displays
Deregister all handsets?
2. Press the YES softkey.
3. The deregistration process takes about 10 seconds to complete. All
handsets show Press [HOLD] on base for 4 sec, then press [#] on
handset when the deregistration completes.
If deregistration fails, you may need to reset the telephone and try again.
To reset:
1. Pick up the registered handset and then press
or
.
2. Press OFF and then place the handset back in the telephone base.
-OR-
1. Unplug the power adapter from the telephone base, then plug it back in.
You cannot deregister a handset if any system handset or telephone base is
in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Getting started
Handset layout
Softkeys (2)
Press to select a menu item displayed above the key.
(speakerphone)
Press to make or join a call using the first available
line, starting with line 1.
Press to answer a call.
During a call, press to switch between speakerphone
and handset use.
/VOL (directory/volume)
Press to enter the directory when the telephone is
not in use.
While in a menu, press to scroll up.
During a call or message playback, press to increase
the listening volume.
(line 1/flash)
Press to make or answer a call on line 1.
During a call, press to receive an incoming call on
line 1 when you receive a call waiting alert.
CID /VOL (caller ID/volume)
Press to review the call log when the telephone is
not in use.
While in a menu, press to scroll down.
During a call or message playback, press to
decrease the listening volume.
1
While reviewing a call log entry, press repeatedly to
add or remove 1 in front of the telephone number
before dialing or saving it in the directory.
TONE
Press to switch to tone dialing temporarily when
using the pulse service.
REDIAL/PAUSE
Press to review the redial list.
While dialing or entering numbers into the directory,
press and hold to insert a dialing pause.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Getting started
Handset layout (continued)
Headset jack
Plug in a wired headset for handsfree telephone
conversation.
CHARGE light
On when the handset is charging in the telephone
base.
OFF
During a call, press to hang up.
Press and hold while the telephone is not in use to
erase the missed calls indicator.
Press to delete a digit or character while entering a
number or name.
While in a menu, press to return to the previous
menu or press and hold to return to the idle mode.
(line 2/flash)
Press to make or answer a call on line 2.
During a call, press to receive an incoming call on
line 2 when you receive a call waiting alert
.
#
Press repeatedly to show other dialing options when
reviewing a call log entry.
INT (intercom)
Press to initiate an intercom conversation or transfer
a call.
HOLD
Press to put a call on hold.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Appendix
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry
tub or swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or
other electrical devices. Protect your phone from moisture, dust, corrosive liquids and fumes.
7. Slots and openings in the back or bottom of the telephone base and handset are provided for
ventilation. To protect them from overheating, these openings must not be blocked by placing
the product on a soft surface such as a bed, sofa or rug. This product should never be placed
near or over a radiator or heat register. This product should not be placed in any area where
proper ventilation is not provided.
8. This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply in your home or office, consult your dealer
or local power company.
9. Do not allow anything to rest on the power cord. Do not install this product where the cord may
be walked on.
10. Never push objects of any kind into this product through the slots in the telephone base or
handset because they may touch dangerous voltage points or create a short circuit. Never spill
liquid of any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this product, but take it to an
authorized service facility. Opening or removing parts of the telephone base or handset other
than specified access doors may expose you to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the product is subsequently used.
12. Do not overload wall outlets and extension cords.
13. Unplug this product from the wall outlet and refer servicing to an authorized service facility
under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operation instructions. Improper adjustment of other
controls may result in damage and often requires extensive work by an authorized technician
to restore the product to normal operation.
E. If the product has been dropped and the telephone base and/or handset has been damaged.
F. If the product exhibits a distinct change in performance.
14. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk
of electric shock from lightning.
15. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain
circumstances, a spark may be created when the adapter is plugged into the power outlet, or
when the handset is replaced in its cradle. This is a common event associated with the closing
of any electrical circuit. The user should not plug the phone into a power outlet, and should
not put a charged handset into the cradle, if the phone is located in an environment containing
concentrations of flammable or flame-supporting gases, unless there is adequate ventilation.
A spark in such an environment could create a fire or explosion. Such environments might
include: medical use of oxygen without adequate ventilation; industrial gases (cleaning
solvents; gasoline vapors; etc.); a leak of natural gas; etc.
16. Only put the handset of your telephone next to your ear when it is in normal talk mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Appendix
Important.safety.instructions
17. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table
or cabinet outlet.
SAVE THESE INSTRUCTIONS
Battery
•
•
CAUTION: Use Only Supplied Battery.
Do not dispose of the battery in a fire. Check with local waste management codes for special
disposal instructions.
•
Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be toxic if swallowed.
Exercise care in handling batteries in order not to create a short circuit with conductive materials.
Charge the battery provided with or identified for use with this product only in accordance with
the instructions and limitations specified in this manual.
•
•
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a
multidisciplinary evaluation of the interference between portable wireless telephones and
implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker.patients
•
•
Should keep wireless telephones at least six inches from the pacemaker.
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket,
when it is turned ON.
•
Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons
using wireless telephones.
About cordless telephones
•
Privacy: The same features that make a cordless telephone convenient create some
limitations. Telephone calls are transmitted between the telephone base and the cordless
handset by radio waves, so there is a possibility that the cordless telephone conversations
could be intercepted by radio receiving equipment within range of the cordless handset. For
this reason, you should not think of cordless telephone conversations as being as private as
those on corded telephones.
•
•
Electrical.power: The telephone base of this cordless telephone must be connected to a
working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls
cannot be made from the cordless handset if the telephone base is unplugged, switched off or if
the electrical power is interrupted.
Potential.TV.interference: Some cordless telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize or prevent such interference, do not place
the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is
experienced, moving the cordless telephone farther away from the TV or VCR often reduces or
eliminates the interference.
•
Rechargeable.batteries: Exercise care in handling batteries in order not to create a short
circuit with conducting material such as rings, bracelets, and keys. The battery or conductor
may overheat and cause harm. Observe proper polarity between the battery and the battery
charger.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Appendix
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain
distance - which can vary with the locations of the telephone base and handset, the weather, and the
layout of your home or office.
When the handset is out of range, the handset displays Out of range OR no power at base.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not
connect well when you press
answer the call.
or . Move closer to the telephone base, then press
or
to
If the handset moves out of range during a telephone conversation, there may be interference. To
improve reception, move closer to the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if
you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or
handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your
own safety, take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean
it only with a soft cloth slightly dampened with water or a mild soap. Do not use excess water or
cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or
standing in the water. If the telephone base should fall into the water, DO NOT RETRIEVE IT
UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL.
Then remove the telephone by the unplugged cords.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Appendix
The RBRC® seal
The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is
voluntarily participating in an industry program to collect and recycle these batteries at the end of
their useful lives, when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-metal hydride
batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions
in your area. VTech’s involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY® are registered trademarks of Rechargeable Battery Recycling
Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Appendix
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital
device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements
are intended to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander according to the intended usage of the product.
This product has been tested and found to comply with the FCC criteria. The handset may be safely
held against the ear of the user. The telephone base shall be installed and used such that parts of
the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches)
or more.
For body worn operation, this handset has been tested and meets the FCC RF exposure guidelines
when used with the accessories supplied or designated for this product. Use of other accessories
may not ensure compliance with FCC RF exposure guidelines.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by
the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX.
This identifier must be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network
must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting
to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect
to your telephone line and still have them ring when you are called. The REN for this product is
encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03,
the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more
information, please contact your telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing
equipment connected to your telephone line, ensure the connection of this equipment does not
disable your alarm equipment. If you have questions about what will disable alarm equipment,
consult your telephone service provider or a qualified installer.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Appendix
FCC, ACTA and IC regulations
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has
been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its
authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may
temporarily discontinue your telephone service. The telephone service provider is required to notify
you before interrupting service. If advance notice is not practical, you will be notified as soon as
possible. You will be given the opportunity to correct the problem and the telephone service provider
is required to inform you of your right to file a complaint with the FCC. Your telephone service
provider may make changes in its facilities, equipment, operation, or procedures that could affect
the proper functioning of this product. The telephone service provider is required to notify you if such
changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada
technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an
indication of the maximum number of devices allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Appendix
California.Energy.Commission.battery.charging.testing.
instructions
This telephone is set up to comply with the energy-conserving standards right out of the box.
These instructions are intended for California Energy Commission (CEC) compliance testing only.
When then CEC battery charging testing mode is activated, all telephone functions, except battery
charging, will be disabled.
To activate the CEC battery charging testing mode:
1. When the phone is not in use, press MENU, , 2, 3, 2, 7, 3, 8, # and then the left softkey on the
*
telephone base.
2. The energy-saving charging mode will be activated in about 60 seconds. You hear a
confirmation tone from the telephone base.
When the phone successfully enters the CEC battery charging testing mode, all cordless
handsets will be deregistered. Then all handsets show Press [HOLD] on base for 4 sec, then
press [#] on handset.
When the phone fails to enter this mode, repeat the steps above.
To.deactivate.the.CEC.battery.charging.testing.mode:
1. Unplug the telephone base power adapter from the power outlet, then plug it back in. Then the
telephone base is powered up as normal.
2. Register the handset back to the telephone base. See page 5 for handset registration instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Appendix
For.C-UL.compliance.only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours
ces mesures préventives de base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs
liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.
4. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine,
d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.
5. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait
tomber et être sérieusement endommagé.
6. Évitez d’installer le système téléphonique dans les endroits soumis à une température extrême,
à la lumière directe du soleil ou à proximité immédiate d’autres appareils électriques ou
électroniques. Protégez votre téléphone contre les sources d’humidité, la poussière, les vapeurs
et les liquides corrosifs.
7. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en
dessous. Afin d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant
l’appareil sur un lit, divan, tapis ou autre surface similaires. Ne placez pas cet appareil à proximité
d’un élément de chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité
murale ou un cabinet fermé qui ne possède pas d’aération adéquate.
8. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de
l’appareil. Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou
votre fournisseur d’électricité.
9. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là
où personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.
10. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient
toucher à des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un
risque d’incendie ou d’électrocution. N’échappez pas de liquides dans l’appareil.
11. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à
un centre de service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez
à des tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à
l’origine d’une électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil
avant de procéder au nettoyage. Utilisez un chiffon humide et doux.
12. Ne surchargez pas les prises de courant et les rallonges.
13. Débranchez cet appareil de la prise de courant et communiquez avec le département de service
à la clientèle de VTech dans les cas suivants:
• Lorsque le cordon d’alimentation est endommagé ou écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement.
Réglez uniquement les commandes indiquées dans le les instructions de fonctionnement. Les
réglages incorrects des autres commandes pourraient provoquer un dommage qui pourrait
exiger un travail exhaustif de la part d’un technicien autorisé afin de rétablir le fonctionnement
normal de l’appareil.
• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.
• Si le produit affiche une nette diminution de sa performance.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Appendix
For.C-UL.compliance.only
14. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à
l’origine d’une électrocution.
15. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une
prise de courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun
associé à la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à
une prise de courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone
se trouve à proximité d’un endroit comportant des concentrations de gaz inflammables, à
moins que la ventilation soit adéquate. Une flammèche dans un tel endroit pourrait provoquer
un incendie ou une explosion. De tels environnements peuvent comprendre: des endroits où
l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de
nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.
16. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de
conversation.
17. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les
broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une
prise au plafond ou sous une table/ armoire.
CONSERVEZ.CES.INSTRUCTIONS
Pile
•
•
MISE EN GARDE : N’utilisez que la pile incluse.
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des
autorités locales.
•
•
•
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait
causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par
des matériaux conducteurs. .
Rechargez la pile incluse ou identifiée pour fonctionner avec cet appareil, selon les instructions
et limites spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs
et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
•
•
•
Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur
cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est en marche.
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction
opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de
simulateurs cardiaques causés par les gens qui utilisent un téléphone sans fil à proximité de
ceux-ci.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Appendix
For.C-UL.compliance.only
À propos des téléphones sans fil
•
Confidentialité : Les mêmes caractéristiques qui constituent des avantages pour les
téléphones sans fil affichent également des restrictions. Les appels téléphoniques sont
transmis entre le combiné sans fil et le socle par le biais d’ondes radio ; il y a donc la possibilité
que vos conversations téléphoniques sans fil soient interceptées par des équipements
de réception radio se trouvant dans la portée du combiné sans fil. Pour cette raison, vous
ne devez pas percevoir les communications téléphoniques sans fil comme étant aussi
confidentielles que celles des téléphones à cordons.
•
•
Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une prise
électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural.
Les appels ne pourront pas être effectués du combiné sans fil si le socle est débranché ou mis
hors tension ou si le courant est coupé.
Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent sur
des fréquences pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour
réduire ou prévenir de telles interférences, ne placez pas le socle du téléphone sans fil près ou
sur un téléviseur ou magnétoscope. S’il y a présence de parasites, il est conseillé d’éloigner
le téléphone sans fil du téléviseur ou du magnétoscope afin de réduire possiblement les
interférences.
•
•
Piles rechargeables.: Manipulez les piles avec soin afin de ne pas les court-circuiter avec des
bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures.
Respectez la polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel :.Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres
piles de ce type, elles pourraient dégager une matière toxique qui peut causer des blessures
corporelles si elles sont brûlées ou percées.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Appendix
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and all accessories provided in the sales package
(“Product”) are free from defects in material and workmanship, pursuant to the following terms
and conditions, when installed and used normally and in accordance with the Product operating
instructions. This limited warranty extends only to the Consumer for Products purchased and used
in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship
during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace
at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may
use new or refurbished replacement parts. If we choose to replace the Product, we may replace
it with a new or refurbished Product of the same or similar design. We will retain defective parts,
modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive
remedy. VTech will return the repaired or replacement Products to you in working condition. You
should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase.
If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty,
this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90
days from the date the repaired or replacement Product is shipped to you or (b) the time remaining
on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage,
improper installation, abnormal operation or handling, neglect, inundation, fire, water or other
liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than
an authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network
reliability, or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial
numbers have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of
America or Canada, or used for commercial or institutional purposes (including but not limited
to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of
systems outside the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Appendix
Limited warranty
How do you get warranty service?
To obtain warranty service in the United States of America, please call 1 (800) 595-9511. In
Canada, please call 1(800) 267-7377. NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and
transportation and are responsible for delivery or handling charges incurred in the transport of
the Product(s) to the service location. VTech will return repaired or replaced Product under this
limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no
risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited
warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify
you and will request that you authorize the cost of repair prior to any further repair activity. You
must pay for the cost of repair and return shipping costs for the repair of Products that are not
covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service
location along with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product
model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other Limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all
other written or oral communications related to this Product. VTech provides no other warranties
for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the
Product. There are no other express warranties. No one is authorized to make modifications to
this limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have
other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one
year from the date of purchase. Some states/provinces do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be
liable for any indirect, special, incidental, consequential, or similar damages (including, but not
limited to lost profits or revenue, inability to use the Product or other associated equipment, the
cost of substitute equipment, and claims by third parties) resulting from the use of this Product.
Some states/provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Appendix
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
Handset: 1921.536-1928.448 MHz
frequency
Telephone base: 1921.536-1928.448 MHz
Channels
5
Nominal
Maximum power allowed by FCC and IC. Actual operating range
effective range may vary according to environmental conditions at the time of use.
Power
requirements
Handset: 2.4V 500mAh Ni-MH battery
Charger: 6V DC @ 400mA
Memory
Handset directory: 50 memory locations;
up to 30 digits and 15 characters
Handset call log: 50 memory locations;
up to 24 digits and 15 characters
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Designed to fit your home.
And your life.
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2014 VTech Communications, Inc.
All right reserved. 12/14. DS6101-X_CIB_V3.0
Document order number: 91-007066-040-100
Download from Www.Somanuals.com. All Manuals Search And Download.
|
