User Guide
Wireless N Access Point
EAP110/EAP120/EAP220
REV1.0.0
1910011184
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT (EAP120&EAP220)
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.”
CE Mark Warning
(EAP110/EAP120)
(EAP220)
This is a class A product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
National Restrictions（only for EAP220）
This device is intended for home and office use in all EU countries (and other countries following
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country
Restriction
Reason/remark
General authorization required for outdoor use and
public service
Bulgaria
None
Outdoor use limited to Military Radiolocation use. Refarming of the 2.4 GHz band
10 mW e.i.r.p. within the has been ongoing in recent years to allow current relaxed
France
band 2454-2483.5 MHz
regulation. Full implementation planned 2012
If used outside of own premises, general authorization is
required
Italy
None
General authorization required for network and service
supply(not for spectrum)
Luxembourg
None
This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Norway
Implemented
None
Russian Federation
Only for indoor applications
5150-5250 MHz
Country
Bulgaria
Croatia
Restriction
Reason/remark
Not implemented
License required
Planned
General authorization required if used outside own
premises
Italy
General authorization required for network and service
supply (not for spectrum)
Luxembourg
None
No info
Russian Federation
Note: Please don’t use the product outdoors in France.
Download from Www.Somanuals.com. All Manuals Search And Download.
IC STATEMENT
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
When there is no power button, the only way to completely shut off power is to disconnect
the product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電
信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
Download from Www.Somanuals.com. All Manuals Search And Download.
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用
者會被要求採取某些適當的對策。
This product can be used in the following countries:
AT
ES
LT
BG
FI
BY
FR
MT
SK
CA
GB
NL
TR
CZ
GR
NO
UA
DE
HU
PL
DK
IE
EE
IT
LV
SE
PT
RO
RU
US
Download from Www.Somanuals.com. All Manuals Search And Download.
About this User Guide
This User Guide is for EAP110, EAP120 and EAP220. Chapter 4 to Chapter 8 are only suitable for
the EAP in Standalone mode. Refer to the EAP Controller User Guide when the EAP is managed
by the EAP Controller software.
Convention
Unless otherwise noted, the EAP or the device mentioned in this guide stands for 300Mbps
Wireless N Access Point EAP110, Wireless N Gigabit Access Point EAP120 and EAP220.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Introduction......................................................................................................................................3
1.2.2 Interface Panel.............................................................................................................................4
1.2.3 Mounting Bracket.......................................................................................................................6
5.1.1 Wireless Basic Settings .......................................................................................................... 13
5.1.2 SSIDs............................................................................................................................................. 14
5.1.3 Wireless Advanced Settings ................................................................................................ 18
5.1.4 Load Balance............................................................................................................................. 19
5.2.1 Portal Configuration............................................................................................................... 20
5.2.2 Free Authentication Policy................................................................................................... 25
QoS......................................................................................................................................................... 33
5.5.1 AP EDCA Parameters.............................................................................................................. 34
5.5.2 Station EDCA Parameters..................................................................................................... 35
5.6.1 Settings ....................................................................................................................................... 37
5.6.2 Detected Rogue AP List ........................................................................................................ 37
5.6.3 Trusted AP List.......................................................................................................................... 38
1
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6.4 Download/Backup Trusted AP List.................................................................................... 38
6.1.1 AP List .......................................................................................................................................... 40
6.2.1 SSID List....................................................................................................................................... 45
6.3.1 User List....................................................................................................................................... 46
6.3.2 Portal Authenticated Guest................................................................................................. 47
7.1.1 Log List ........................................................................................................................................ 49
7.1.2 Log Settings............................................................................................................................... 50
8.2.1 Time Settings ............................................................................................................................ 58
8.2.2 Daylight Saving........................................................................................................................ 59
Reboot/Reset...................................................................................................................................... 60
Appendix A: Specifications.................................................................................................................................... 63
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
1.1 Overview of the EAP
EAP series products provide wireless coverage solutions for small-medium business. They can
either work independently as standalone APs or be centrally managed by the EAP Controller
software, providing a flexible, richly-functional but easily-configured enterprise-grade wireless
network for small and medium business.
“Celling lamp” appearance and easily mounting design with chassis make EAP easy to be
installed on a wall or ceiling and blend in with most interior decorations.
EAP110 is provided with a passive PoE adapter for power supply. EAP120/EAP220 can be
powered via a PSE* device or the provided power adapter.
With two built-in omnidirectional antennas, both EAP110 and EAP120 work within the 2.4GHz
frequency band and apply 802.11 standards and 2*2MIMO technology, allowing packet
transmission at up to 300Mbps.
EAP220 has four built-in omnidirectional antennas. Wireless network created by EAP220 can
operate at both 2.4GHz and 5GHz. It applies 802.11n standard and two 2*2MIMO technology,
allowing packet transmission at up to 600Mbps (300Mbps per radio).
*PSE: Power Sourcing Equipment, a device (switch or hub for instance) that will provide power
in a PoE setup.
1.2 Hardware Overview
1.2.1 LED
EAP110, EAP120 and EAP220 have the same LED status and corresponding indications.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1-1 Top View of the EAP
LED Status
Solid green
Flashing red
Indication
The device is working properly.
System errors. RAM, flash, Ethernet, WLAN or
firmware may be malfunctioning.
Flashing yellow
Firmware update is in progress. Do not
disconnect or power off the device.
The device is being reset to its factory default
settings.
Double-flashing red, green, yellow
1.2.2 Interface Panel
EAP110:
Figure 1-2 Interface Panel of EAP110
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EAP120/EAP220:
Figure 1-3 Interface Panel of EAP120/EAP220
Please note that EAP110 does not have the CONSOLE port, POWER port and ON/OFF button. The
interface panel components of the EAP, from left to right, are described in the following list.
Kensington Security Slot: Secure the lock (not provided) into the security slot to prevent
the device from being stolen.
RESET: With the device powered on, press and hold the RESET button for about 8 seconds
until the LED flashes red, then release the button. The device will restore to factory default
settings.
CONSOLE: This port is used to connect to the serial port of a computer or a terminal to
check and monitor system information of the EAP120/EAP220.
Note: CLI commands are not available in current software version. We will release a new
version supporting CLI commands soon. Please pay close attention to our official website.
ARROW 1: This arrow is used to align with ARROW 2 on the mounting bracket to lock the
EAP into place.
ETHERNET:
For EAP110, this port is used to connect to the POE port of the provided PoE adapter for
both data transmission and power supply through Ethernet cabling.
For EAP120/EAP220, this port is used to connect to a router to transmit data or to a PSE
(Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power
over Ethernet (PoE) through Ethernet cabling.
ON/OFF: Press this button to turn on/off the EAP120/EAP220.
POWER: The power port is used to connect the EAP120/EAP220 to an electrical wall outlet
via power adapter. Please only use the provided power adapter.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Passive PoE Adapter:
Power LED: The Power LED indicates the status of the electric current: green (0-0.8A), red
(0.8A-1A).
POE Port: This port is used to connect the ETHERNET port of the EAP110.
LAN Port: This port is used to connect your LAN.
1.2.3 Mounting Bracket
The following figure describes the structure of the mounting bracket.
Figure 1-4 Layout of the Mounting Bracket
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Network Topology
A typical network topology for the EAP is shown below.
Figure 2-1 Typical Topology
To deploy an EAP in your local network, a DHCP server is required to assign IP addresses to the
EAP and clients. Typically, a router acts as the DHCP server. Ensure the EAPs are in the same
subnet with the Controller Host in which the EAP Controller is installed.
The EAP can be managed by the EAP Controller software, which is a management software
specially designed for the TP-LINK EAP devices on a local wireless network, allowing you to
centrally configure and monitor mass EAP devices using a web browser on your PC. For more
information about the EAP Controller, please refer to the EAP Controller User Guide in the
resource CD or download it from our official website:
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Management Mode
300Mbps Wireless N Access Point EAP110 and Wireless N Gigabit Access Point EAP120/EAP220
can either work under the control of the EAP Controller software or work independently as a
standalone access point.
When user establishes a large-scale wireless network, the management of every single AP in
the network is complex and complicated. With the EAP Controller software, you can centrally
manage the mass APs simply in a web browser.
The Standalone mode applies to a relatively small-sized wireless network. EAPs in the Standalone
mode cannot be managed centrally by the EAP Controller software.
3.1 Standalone Mode
By default, the EAP works independently as a standalone access point. By entering the IP
address of the standalone EAP, you can log in to its web interface and perform configurations.
The factory default IP address configuration of the EAP is DHCP (Dynamic Host Configuration
Protocol). Before you access the web interface of the EAP, please make sure the DHCP server
works properly. Typically, a router acts as the DHCP server.
Follow the steps below to log in to the web interface of a standalone EAP.
1. Launch a web browser, enter the DHCP address in the address field and press the Enter key.
2. Enter admin (all lowercase) for both username and password.
3.2 Managed Mode
The EAP will become a managed AP once it is adopted via the EAP Controller software. Users
can manage the AP via a web browser. Refer to the EAP Controller User Guide to know more
about EAP Controller software.
3.3 Switch to Standalone Mode
The web interface of a specific EAP is not available once this EAP is adopted by the EAP
Controller. You can Forget the EAP via the EAP Controller to turn it back as a standalone AP.
Refer to the EAP Controller User Guide to learn more.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TIPS:
Proceed to the following chapters for information on using the EAP in standalone mode. EAP110
is taken as the example.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Network
On Network page you can configure the IP address of the standalone EAP.
Figure 4-1 Network Page
By default, the EAP device obtains an IP address from a DHCP server (typically a
router). Select Static to configure IP address manually.
Dynamic/Static:
Fallback IP:
If the EAP fails to get a dynamic IP address from a DHCP server within ten
seconds, the fallback IP will work as the IP address of the device. After that,
however, the device will keep trying to obtain an IP address from the DHCP
server until it succeeds.
Enter the fallback IP/IP mask.
DHCP Fallback
IP/IP MASK:
Enter the fallback gateway.
DHCP Fallback
Gateway:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1.1 Wireless Basic Settings
Figure 5-3 Wireless Basic Settings
Check the box to enable 2.4GHz Wireless Radio.
2.4GHz Wireless
Radio:
Select the protocol standard for the wireless network.
Wireless Mode:
Wireless network created by the EAP is able to operate in the 2.4GHz frequency
The EAP supports 802.11b/g/n, 802.11b/g, and 802.11n standards. It is
recommended to select 802.11b/g/n, in which way clients supporting 11b, 11g
or 11n mode can access your wireless network.
EAP220 the wireless network can work within 2.4GHz and 5GHz frequency.
Wireless network of EAP220 operating at 5GHz frequency band supports
802.11a/n, 802.11a and 802.11n standards. It is recommended to select
802.11a/n, in which way your wireless network can be connected by clients
supporting 11a or 11n mode.
Select the channel width of this device. Options include 20MHz, 40MHz and
20/40MHz (this device automatically selects 20MHz or 40MHz, and 20MHz will
be used if 40MHz is not available). According to IEEE 802.11n standard, using a
channel width of 40MHz can increase wireless throughput. However, users
may choose lower bandwidth due to the following reasons:
Channel Width:
1. To increase the available number of channels within the limited total
bandwidth.
2. To avoid interference from overlapping channels occupied by other
devices in the environment.
3. Lower bandwidth can concentrate higher transmit power, increasing
stability of wireless links over long distances.
Select the channel used by this device to improve wireless performance.
1/2412MHz means the Channel is 1 and the frequency is 2412MHz. The
channel number varies in different regions. By default, channel is automatically
selected.
Channel:
Enter the transmit power value. By default, the value is 20. The maximum
transmit power may vary among different countries or regions.
Tx power:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
If the maximum transmit power is set to be larger than local regulation allows,
the maximum Tx power regulated will be applied in actual situation.
NOTE: In most cases, it is unnecessary to select maximum transmit power.
Selecting larger transmit power than needed may cause interference to
neighborhood. Also it consumes more power and will reduce longevity of the
device. Select a certain transmit power is enough to achieve the best
performance.
5.1.2 SSIDs
SSIDs can work together with switches supporting 802.1Q VLAN. The EAP can build up to eight
virtual wireless networks per radio for users to access. At the same time, it adds different VLAN
tags to the clients which connect to the corresponding wireless network. It supports maximum
8 VLANs per radio. The clients in different VLAN cannot directly communicate with each other.
Clients connected to the device via cable do not belong to any VLAN. Thus wired client can
communicate with all the wireless clients despite the VLAN settings.
Click
in the Modify column, the following content will be shown.
Figure 5-4 SSIDs
Click to add up to 8 wireless networks per radio.
Enter up to 32 characters as the SSID name.
SSID Name:
Set a VLAN ID (ranges from 0 to 4094) for the wireless network. VLAN 0 means
VLAN function is disabled. Wireless networks with the same VLAN ID are grouped
to a VLAN.
Wireless VLAN
ID:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Enable this function, AP will broadcast its SSID to hosts in the surrounding
environment, as thus hosts can find the wireless network identified by this SSID. If
SSID Broadcast is not enabled, hosts must enter the AP’s SSID manually to connect
to this AP.
SSID
Broadcast:
Select the security mode of the wireless network. For the security of wireless
network, you are suggested to encrypt your wireless network. This device
provides three security modes: WPA-Enterprise, WPA-PSK (WPA Pre-Shared Key)
and WEP (Wired Equivalent Privacy). WPA-PSK is recommended. Settings vary in
different security modes as the details are in the following introduction. Select
None and the hosts can access the wireless network without password.
Security Mode:
Portal provides authentication service for the clients who want to access the
Portal:
After enabling SSID Isolation, the devices connected in the same SSID cannot
communicate with each other.
SSID Isolation:
Modify:
Click
Click
to open the page to edit the parameters of SSID.
to delete the SSID.
WEP
WEP (Wired Equivalent Privacy), based on the IEEE 802.11 standard, is less safe than WPA-
Enterprise or WPA-PSK.
NOTE:
WEP is not supported in 802.11n mode. If WEP is applied in 802.11n mode, the clients may not be
able to access the wireless network. If WEP is applied in 11b/g/n mode (in the 2.4GHz frequency
band) or 11a/n (in the 5GHz frequency band), the device may work at a low transmission rate.
Figure 5-5 Security Mode_WEP
Select the authentication type for WEP.
Type:
Auto: The default setting is Auto, which can select Open System or Shared Key
automatically based on the wireless station's capability and request.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Open System: After you select Open System, clients can pass the
authentication and associate with the wireless network without password.
However, correct password is necessary for data transmission.
Shared Key: After you select Shared Key, clients has to input password to pass
the authentication, or it cannot associate with the wireless network or
transmit data.
You can configure four keys in advance and select one as the present valid key.
Select the wep key format ASCII or Hexadecimal.
Key Selected:
Wep Key
Format:
ASCII: ASCII format stands for any combination of keyboard characters in the
specified length.
Hexadecimal: Hexadecimal format stands for any combination of
hexadecimal digits (0-9, a-f, A-F) in the specified length.
Select the WEP key length (64-bit, or 128-bit, or 152-bit) for encryption.
Key Type:
64-bit: You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F
without null key) or 5 ASCII characters.
128-bit: You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-
F without null key) or 13 ASCII characters.
152-bit: You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-
F without null key) or 16 ASCII characters.
Enter the key value.
Key Value:
WPA-Enterprise
Based on RADIUS server, WPA-Enterprise can generate different passwords for different users and
it is much safer than WPA-PSK. However, it costs much to maintain and is more suitable for
enterprise users. At present, WPA-Enterprise has two versions: WPA-PSK and WPA2-PSK.
Figure 5-6 Security Mode_WPA-Enterprise
Select one of the following versions:
Version:
Auto: Select WPA-PSK or WPA2-PSK automatically based on the wireless
station's capability and request.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
WPA-PSK: Pre-shared key of WPA.
WPA2-PSK: Pre-shared key of WPA2.
Encryption:
Select the encryption type, including Auto, TKIP, and AES. The default setting
is Auto, which can select TKIP (Temporal Key Integrity Protocol) or AES
(Advanced Encryption Standard) automatically based on the wireless station's
capability and request. AES is more secure than TKIP and TKIP is not supported
in 802.11n mode. It is recommended to select AES as the encryption type.
Enter the IP address/port of the RADIUS server.
RADIUS Server
IP/Port:
Enter the shared secret of RADIUS server to access the RADIUS server.
RADIUS
Password:
Specify the group key update period in seconds. The value can be either 0 or
at least 30. 0 means no update.
Group Key
Update period:
NOTE:
Encryption type TKIP is not supported in 802.11n mode. If TKIP is applied in 802.11n mode, the
clients may not be able to access the wireless network of the EAP. If TKIP is applied in 11b/g/n
mode (in the 2.4GHz frequency band) or 11a/n (in the 5GHz frequency band), the device may work
at a low transmission rate.
WPA-PSK
Based on pre-shared key, security mode WPA-PSK is characterized by high security and simple
configuration, which suits for common households and small business. WPA-PSK has two
versions: WPA-PSK and WPA2-PSK.
Figure 5-7 Security Mode_WPA-PSK
Auto: Select WPA or WPA2 automatically based on the wireless station's
Version:
capability and request.
WPA: Pre-shared key of WPA.
WPA2: Pre-shared key of WPA2.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Encryption:
Select the encryption type, including Auto, TKIP, and AES. The default setting is
Auto, which can select TKIP (Temporal Key Integrity Protocol) or AES (Advanced
Encryption Standard) automatically based on the wireless station's capability
and request. AES is more secure than TKIP and TKIP is not supported in 802.11n
mode. It is recommended to select AES as the encryption type.
Configure the WPA-PSK/WPA2-PSK password with ASCII or Hexadecimal
characters. For ASCII, the length should be between 8 and 63 characters with
combination of numbers, letters (case-sensitive) and common punctuations. For
Hexadecimal, the length should be 64 characters (case-insensitive, 0-9, a-f, A-F).
Wireless
Password:
Specify the group key update period in seconds. The value can be either 0 or at
least 30. 0 means no update.
Group Key
Update Period:
5.1.3 Wireless Advanced Settings
Figure 5-8 Wireless Advanced Settings
Beacons are transmitted periodically by the device to announce the presence of a
wireless network for the clients. Beacon Interval value determines the time
interval of the beacons sent by the device. You can specify a value from 40 to 100.
The default value is 100 milliseconds.
Beacon
Interval:
This value indicates the number of beacon intervals between successive Delivery
Traffic Indication Messages (DTIMs) and this number is included in each Beacon
frame. A DTIM is contained in Beacon frames to indicate whether the access point
has buffered broadcast and/or multicast data for the client devices. Following a
Beacon frame containing a DTIM, the access point will release the buffered
broadcast and/or multicast data, if any exists. You can specify the value between
1-255 Beacon Intervals. The default value is 1, indicating the DTIM Period is the
same as Beacon Interval. An excessive DTIM period may reduce the performance
of multicast applications. It is recommended to keep it by default.
DTIM Period:
When the RTS threshold is activated, all the stations and APs follow the Request
to Send (RTS) protocol. When the station is to send packets, it will send a RTS to
AP to inform the AP that it will send data. After receiving the RTS, the AP notices
other stations in the same wireless network to delay their transmitting of data. At
the same time, the AP inform the requesting station to send data. The value range
is from 1 to 2347 bytes. The default value is 2347, which means that RTS is
disabled.
RTS Threshold:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Specify the fragmentation threshold for packets. If the size of the packet is larger
than the fragmentation threshold, the packet will be fragmented into several
packets. Too low fragmentation threshold may result in poor wireless
performance caused by the excessive packets. The recommended and default
value is 2346 bytes.
Fragmentation
Threshold:
5.1.4 Load Balance
By restricting the maximum number of clients accessing the EAPs, Load Balance helps to achieve
rational use of network resources.
Figure 5-9 Load Balance
Load Balance:
Disable by default. Click ON to enable the function. After enabling it, you
can set a number for maximum associated clients to control the wireless
access.
Enter the number of clients to be allowed for connection to the EAP. The
number ranges from 1 to 99.
Maximum
Associated Clients:
5.2 Portal
Portal authentication enhances the network security by providing authentication service to the
clients who want to access the wireless local network. Portal is also called web authentication.
The users have to log in a web page to establish verification.
Network resources can be classified into different types for different users. Part of them can be
accessed for free by the clients; while some specific resources can only be accessed by authorized
users. What’s more, you can customize the authentication login page and specify a URL which
Authentication Policy according to your need.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Following is the page of Portal.
Figure 5-10 Portal Page
NOTE:
To apply Portal in a wireless network, please go to Wireless→Wireless Settings→SSIDs to enable
Portal of a selected SSID.
5.2.1 Portal Configuration
Three authentication types are available: No Authentication, Local Password and External
RADIUS Server.
1. No Authentication：Users are required to finish only two steps: agree with the user protocol
and click the Login button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Local Password：Users are required to enter the preset user name and password, which are
saved in the EAP.
3. External RADIUS Server：Users are required to enter the preset user name and password,
which are saved in the database of the RADIUS server. The RADIUS server acts as the
authentication server, which allows you to set different user name and password for
different users.
Refer to the following content to configure Portal based on actual network situations.
No Authentication
Figure 5-11 Portal Configuration_No Authentication
Authentication
Type:
Select No Authentication.
After successful verification, an authentication session is established.
Authentication Timeout decides the active time of the session. Within the
active time, the device keeps the authentication session open with the
associated client. To reopen the session, the client needs to log in the web
authentication page and enter the user name and password again once
authentication timeout is reached.
Authentication
Timeout:
By default, authentication timeout is one hour. Select Custom from the drop-
down list to customize the parameter.
Disable by default. Redirect specifies that the portal should redirect the newly
authenticated clients to the configured URL.
Redirect:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the URL that a newly authenticated client will be directed to.
Redirect URL:
Select Local Web Portal, the authentication login page will be provided by the
built-in portal server.
Portal
Customization:
The page configured below will be presented to users as the login page. Words
can be filled in Input Box 1 and Input Box 2.
Enter up to 31 characters as the title of the authentication login page in Input
Box 1, like “Guest Portal of TP-LINK”.
Enter the terms presented to users in Input Box 2. The terms can be 1 to 1023
characters long.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Local Password
Figure 5-12 Portal Configuration_Local Password
Authentication Type:
Username:
Select Local Password.
Enter the user name for local authentication.
Enter the password for local authentication.
Password:
URL, and Portal Customization.
External RADIUS Server
External RADIUS Server provides two types of portal customization: Local Web Portal and
External Web Portal. The authentication login page of Local Web Portal is provided by the built-
23
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Local Web Portal
Figure 5-13 Portal Configuration_External RADIUS Server_Local Web Portal
Authentication Type: Select External RADIUS Server.
Enter the IP address of the RADIUS server.
RADIUS Server IP:
Port:
Enter the port for authentication service.
Enter the shared secret of RADIUS server to log in to the RADIUS server.
RADIUS Password:
URL, and Portal Customization.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
2. External Web Portal
Figure 5-14 Portal Configuration_External RADIUS Server_External Web Portal
Authentication Type:
RADIUS Server IP:
Port:
Select External RADIUS Server.
Enter the IP address of the RADIUS server.
Enter the port for authentication service.
Enter the shared secret of RADIUS server to log in to the RADIUS server.
Select External Web Portal.
RADIUS Password:
Portal Customization:
Enter the authentication login page’s URL, which is provided by the
remote portal server.
External Web Portal
URL:
URL.
5.2.2 Free Authentication Policy
Free Authentication Policy allows clients to access network resources for free. On the lower part
of the Portal page you can configure and view free authentication policies.
Figure 5-15 Free Authentication Policy
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Click
to add a new authentication policy and configure its parameters.
Figure 5-16 Configure Free Authentication Policy
Enter a policy name.
Policy Name:
Enter the source IP address and subnet mask of the clients who can enjoy the
free authentication policy. Leaving the field empty means all IP addresses can
access the specific resources.
Source IP
Range:
Destination IP
Range:
Enter the destination IP address and subnet mask for free authentication policy.
Leaving the field empty means all IP addresses can be visited. When External
Radius Server is configured and External Web Portal is selected, please set
the IP address and subnet mask of your external web server as the Destination
IP Range.
Enter the source MAC address of the clients who can enjoy the free
authentication policy. Leaving the field empty means all MAC addresses can
access the specific resources.
Source MAC:
Enter the destination port for free authentication policy. Leaving the field
empty means all ports can be accessed.
Destination
Port:
Check the box to enable the policy.
Status:
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5-17 Add Free Authentication Policy
192.168.2.0/24 are able to visit IP range 10.10.10.0/24. Policy 1 is enabled.
Click
to edit the policy. Click
to delete the policy.
5.3 MAC Filtering
MAC Filtering uses MAC addresses to determine whether one host can access the wireless
network or not. Thereby it can effectively control the user access in the wireless network.
Figure 5-18 MAC Filtering Page
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Check the box to enable MAC Filtering.
Enable MAC Filtering:
Station MAC Group
Follow the steps below to add MAC groups.
Step 1:
Click
, two tables will be shown.
Figure 5-19 Station MAC Group
Step 2:
Click
and fill in a name for the MAC group.
Figure 5-20 Add a Group
Step 3:
Click
and input the MAC address you want to organize into this group.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5-21 Add a Group Member
Click
in Modify column to edit the MAC group name or MAC address. Click
to delete the
MAC group or group member.
MAC Filtering Association
Figure 5-22 MAC Filtering Association
Displays the SSID of the wireless network.
SSID Name:
Band:
Displays the frequency band the wireless network operates at.
Select a MAC group from the drop-down list to allow or deny its members
to access the wireless network.
MAC Group Name:
Allow: Allow the access of the stations specified in the MAC group.
Action:
Deny: Deny the access of the stations specified in the MAC group.
5.4 Scheduler
Scheduler allows you to configure rules with specific time interval for radios to operate, which
automates the enabling or disabling of the radio.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5-23 Scheduler Page
Settings
Check the box to enable Scheduler.
Scheduler:
Association Mode:
Select Associated with SSID/AP, you can perform configurations on the
here.
Scheduler Profile Configuration
Follow the steps below to add rules.
Step 1:
Click
, two tables will be shown.
Figure 5-24 Scheduler Profile Configuration
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2:
Click
and input a profile name for the rule.
Figure 5-25 Add a Profile
Step 3:
Click
and configure the recurring schedule for the rule.
Figure 5-26 Add a Rule
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Scheduler Association
1. Associated with SSID
Figure 5-27 Scheduler Association_Associated with SSID
Displays the SSID of the standalone AP.
SSID Name:
Band:
Displays the frequency band which the wireless network operates at.
Select a profile name from the drop-down list. Profile name is configured in
Profile Name:
Action:
Select Radio On/Off to turn on/off the wireless network during the time
interval set for the profile.
2. Associated with AP
Figure 5-28 Scheduler Association_Associated with AP
Displays the name of the device.
AP:
Displays the MAC address of the device.
AP MAC:
Profile Name:
Select a profile name from the drop-down list. Profile name is configured in
Action:
Select Radio On/Off to turn on/off the wireless network during the time
interval set for the profile.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5 QoS
The EAP supports Quality of Service (QoS) to prioritize voice and video traffic over other traffic
types.
In normal use, the default values for the EAP device and station EDCA should not need to be
changed. Changing these values affects the QoS provided.
Figure 5-29 QoS Page
By default, WMM is enabled. After WMM is enabled, the device has the QoS
function to guarantee the transmission of audio and video packets with high
priority.
Wi-Fi Multimedia
(WMM):
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5.1 AP EDCA Parameters
AP Enhanced Distributed Channel Access (EDCA) parameters affect traffic flowing from the EAP
device to the client station.
Figure 5-30 AP EDCA Parameters
Displays the transmission queues: Data 0>Data 1>Data 2>Data 3.
Queue:
A wait time for data frames. The wait time is measured in slots. Valid values
for AIFS are from 1 to 15.
Arbitration Inter-
Frame Space:
An input to the algorithm that determines the initial random backoff wait
time (window) for retry of a transmission.
Minimum
Contention
Window:
The upper limit (in milliseconds) for the doubling of the random backoff
value.
Maximum
Contention
Window:
This parameter applies only to traffic flowing from EAP to the client station.
Maximum Burst
This value specifies (in milliseconds) the maximum burst length allowed for
packet bursts on the wireless network. A packet burst is a collection of
multiple frames transmitted without header information. The decreased
overhead results in higher throughput and better performance. Valid values
for Maximum Burst are from 0 to 8192 and should be exactly divided by 32.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5.2 Station EDCA Parameters
Station EDCA parameters affect traffic flowing from the client station to the EAP device.
Figure 5-31 Station EDCA Parameters
Displays the transmission queues: Data 0>Data 1>Data 2>Data 3.
Queue：
A wait time for data frames. The wait time is measured in slots. Valid
values for AIFS are 1 through 15.
Arbitration Inter-
Frame Space：
An input to the algorithm that determines the initial random backoff wait
time (window) for retry of a transmission.
Minimum Contention
Window：
The upper limit (in milliseconds) for the doubling of the random backoff
value.
Maximum
Contention
Window：
The Transmission Opportunity (TXOP) is an interval of time, in
milliseconds, when a WME client station has the right to initiate
transmissions onto the wireless medium towards the EAP device. Valid
values for TXOP Limit are from 0 to 8192 and should be exactly divided
by 32.
TXOP Limit：
No
Select Enable to specify that the EAP device should not acknowledge
frames with QosNoAck as the service class value. By default, it is disabled.
Acknowledgement：
Unscheduled
Automatic Power
Save Delivery：
Select Enable to enable APSD, which is a power management method.
APSD is recommended if VoIP phones access the network through the
EAP device. By default, it is enabled.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6 Rogue AP Detection
A Rogue AP is an access point that has been installed on a secure network without explicit
authorization from a system administrator.
The EAP device can scan all channels to detect all APs in the vicinity of the network. If rogue APs
are detected, they are shown on the Detected Rogue AP List. If an AP listed as a rogue is
legitimate, you can add it to the Trusted AP List.
Figure 5-32 Rogue AP Detection Page
36
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6.1 Settings
Figure 5-33 Enable Rogue AP Detection
Rogue AP Detection:
Check the box to enable Rogue AP Detection, then click Save.
5.6.2 Detected Rogue AP List
Information about the detected rogue APs is displayed in the list. By default, the status of the
detected rogue AP is unknown. You can click Known in Action column to move the AP to the
Trusted AP List.
Figure 5-34 Detected Rogue AP List
Click to scan rogue APs. Make sure you have enabled Rogue AP Detection and
saved the setting before you click the button.
Action:
Click Known to move the AP to the Trusted AP List. After the configurations are
saved, the moved AP will not be displayed in the Detected Rogue AP List.
The MAC address of the rogue AP.
The SSID for the rogue AP.
MAC:
SSID:
Band:
Displays the frequency band which the wireless network of the rogue AP operates
at.
The channel on which the rogue AP is currently broadcasting.
Channel:
Security:
Displays the enabling or disabling of the security mode of the wireless network.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
The beacon interval used by the rogue AP.
Beacon
Interval:
Beacon frames are transmitted by an AP at regular intervals to announce the
existence of the wireless network. The default behavior is to send a beacon frame
once every 100 milliseconds (or 10 per second).
The strength of the radio signal emitting from the rogue AP.
Signal:
5.6.3 Trusted AP List
Information about the trusted APs is displayed in the list.
Figure 5-35 Trusted AP List
Action:
MAC:
Click Unknown to move the AP out of the Trusted AP List.
The MAC address of the trusted AP.
The SSID for the trusted AP.
SSID:
Displays the frequency band which the wireless network of the trusted AP operates
at.
Band:
The channel on which the trusted AP is currently broadcasting.
Channel:
Security:
Displays the enabling or disabling of the security mode of the wireless network.
5.6.4 Download/Backup Trusted AP List
You can import a list of trusted APs from a saved list which is acquired from another AP or created
from a text file. The AP whose MAC address is in the Trusted AP List will not be detected as a
rogue.
You can also backup a list and save it in your PC.
Figure 5-36 Download/Backup Trusted AP List
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Save Action:
Select Download (PC to AP) to import a trusted AP list to the device.
Select Backup (AP to PC) to copy the trusted AP list to your PC.
Source File
Name:
Click Browse and choose the path of a saved trusted AP list or to save a
trusted AP list.
File
Select Replace to import the list and replace the contents of the Trusted AP
List.
Management:
Select Merge to import the list and add the APs in the imported file to the
APs currently shown in the Trusted AP List
NOTE:
EAP device does not have any control over the APs in the Detected Rogue AP List.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Monitoring
SSID and Client.
6.1 AP
AP List on the Monitoring page displays the device name, its MAC address and the number of
clients. Below the AP List the AP’s detailed information will be shown, including Device
Figure 6-1 AP Monitoring
6.1.1 AP List
Figure 6-2 AP List
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays the device name.
Device Name:
MAC:
Displays the MAC address of the EAP.
Displays the number of clients connected to the EAP.
Num of Clients:
Device Information
Figure 6-3 Device Information
Displays the device name.
Displays the model of the device.
Device Name:
Device Model:
Displays the firmware version of the device. If you want to upgrade the firmware,
Firmware
Version:
Displays the system time of the device. If you want to adjust the system time,
System Time:
Displays the time that has elapsed since the last reboot.
Uptime:
CPU:
Displays the CPU occupancy, which helps you to preliminarily judge whether the
device functions properly.
Displays the memory usage , which helps you to preliminarily judge whether the
device functions properly.
Memory:
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Settings
Figure 6-4 Wireless Settings
Displays the region you’ve selected.
Region:
Displays the channel number and the operating frequency. If you want
Channel/Frequency:
Displays the spectral width of the radio channel used by the device. If
Channel Width:
IEEE802.11 Mode:
Max TX Rate:
Displays the radio standard used for operation of your device. If you
Displays the maximum data rate at which the device should transmit
wireless packets.
Displays the maximum average transmit power of the device. If you
Transmit Power:
LAN Information
Figure 6-5 LAN Information
Displays the MAC address of the device.
Displays the IP address of the device.
Displays the subnet mask of the device.
MAC Address:
IP Address:
Subnet Mask:
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays the maximum transmission rate and duplex mode (half-duplex or
full-duplex) of the port.
LAN Port:
Client
Figure 6-6 Client
Displays the MAC address of the client of the AP selected in AP List.
Displays the SSID the client is connected to.
MAC:
SSID:
Signal to Noise Ratio, the power ratio between the received wireless signal
strength and the environmental noise strength. The bigger the value of SNR, the
better network performance the device provides.
SNR(dB):
Displays the wireless Client Connection Quality (CCQ). CCQ refers to the ratio of
current effective transmission bandwidth and the theoretically maximum
available bandwidth. CCQ reflects the actual link condition.
CCQ(%):
Displays the data rate at which the client transmits wireless packets.
Displays the throughput of the downstream data.
Rate(Mbps):
Down(Byte):
Up(Byte):
Displays the throughput of the upstream data.
Displays the amount of time the client has been connected to the device.
Active Time:
LAN Traffic
Click LAN Traffic and you can monitor the data transmission status of the LAN port.
Figure 6-7 LAN Traffic
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays the total amount of packets received/sent on the LAN port.
Displays the total amount of data (in bytes) received/sent on the LAN port.
Rx/Tx Packets:
Rx/Tx Bytes:
Displays the total amount of dropped packets received/sent on the LAN
port.
Rx/Tx Dropped
Packets:
Displays the total amount of error packets received/sent on the LAN port.
Rx/Tx Errors:
Radio Traffic
Click Radio Traffic and you can monitor the data transmission status of the wireless network.
Figure 6-8 Radio Traffic
Displays the total amount of packets received/sent by the wireless network.
Rx/Tx Packets:
Rx/Tx Bytes:
Displays the total amount of data (in bytes) received/sent by the wireless
network.
Displays the total amount of dropped packets received/sent by the wireless
network.
Rx/Tx Dropped
Packets:
Displays the total amount of error packets received/sent by the wireless
network.
Rx/Tx Errors:
44
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2 SSID
Figure 6-9 SSID Monitoring
6.2.1 SSID List
In SSID List you can monitor the related parameters of the wireless network.
Figure 6-10 SSID List
SSID Name:
VLAN ID:
Displays the VLAN which the SSID belongs to. If you want to change the VLAN
Displays the number of clients connected to the SSID. If you want to get more
Num of Clients:
SSID Broadcast:
Displays the enabling or disabling of SSID broadcast. If you want to modify it,
Displays the frequency band the wireless network is operating at.
Band:
Displays the security mode the wireless network is applying. If you want to
Security:
Displays the enabling or disabling of Portal. If you want to modify it, please
Portal:
Displays the enabling or disabling of MAC Filtering. If you want to modify it,
MAC Filtering:
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays the enabling or disabling of SSID Isolation. If you want to modify it,
Isolation:
Displays the throughput of the downstream data.
Displays the throughput of the upstream data.
Down(Byte):
Up(Byte):
6.3 Client
From User List, you can monitor the status of all the clients connected to the EAP including those
who are authenticated.
Figure 6-11 Client Monitoring
6.3.1 User List
Figure 6-12 User List
Displays the MAC address of the client.
MAC:
Displays the name of the device to which the client is connected.
Displays the SSID the client is connected to.
Access Point:
SSID:
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal to Noise Ratio, the power ratio between the received wireless signal
strength and the environmental noise strength. The bigger the value of SNR, the
better network performance the device provides.
SNR(dB):
CCQ(%):
Displays the wireless Client Connection Quality (CCQ). CCQ refers to the ratio of
current effective transmission bandwidth and the theoretically maximum
available bandwidth. CCQ reflects the actual link condition.
Displays the data rate at which the client transmits wireless packets.
Displays the throughput of the downstream data.
Rate(Mbps):
Down(Byte):
Up(Byte):
Displays the throughput of the upstream data.
Displays the amount of time the client has been connected to the device.
Active Time:
6.3.2 Portal Authenticated Guest
The Portal Authenticated Guest displays information about clients that have set up valid
authentication.
Figure 6-13 Portal Authenticated Guest
Displays the MAC address of the authenticated client.
MAC:
Displays the name of the device to which the authenticated client is connected
Displays the SSID the authenticated client is connected to.
Access Point:
SSID:
Signal to Noise Ratio, the power ratio between the received wireless signal
strength and the environmental noise strength. The bigger the value of SNR, the
better network performance the device provides.
SNR(dB):
Displays the Client Connection Quality (CCQ) of the authenticated client. CCQ
refers to the ratio of current effective transmission bandwidth and the
theoretically maximum available bandwidth. CCQ reflects the actual link
condition.
CCQ(%):
Displays the data rate at which the authenticated client transmits wireless
packets.
Rate(Mbps):
Displays the throughput of the downstream data.
Displays the throughput of the upstream data.
Down(Byte):
Up(Byte):
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays the amount of time the authenticated client has been connected to the
root AP.
Active Time:
Action:
Click Unauthorize to stop giving authorization to the clients connected to the
wireless network.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Management
Management page is mainly used for device management and maintenance.
7.1 System Log
System log records information about hardware, software as well as system issues and monitors
system events. With the help of system log, you can get informed of system running status and
detect the reasons for failure.
Following is the page of System Log.
Figure 7-1 System Log Page
7.1.1 Log List
From Log List you can view detailed information about hardware, software, system issues and so
on.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7-2 Log List
7.1.2 Log Settings
You can choose the way to receive system logs in Log Settings zone, where these parameters can
Figure 7-3 Log Settings
Enable Auto Mail
If Auto Mail is enabled, system logs will be sent to a mailbox. The following content will be shown.
Figure 7-4 Enable Auto Mail
Enter the sender’s email address.
From:
To:
Enter the recipient’s email address, which will receive the system logs.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the IP address of the SMTP server.
SMTP Server:
Generally users are required to log in to the SMTP server by entering user
name and password.
Enable
Authentication:
User Name: Enter the sender’s email address.
Password: Enter the password of the sender’s email address.
Confirm Password: Enter the password again for confirmation.
System logs can be sent at specific time or time interval.
Time Mode:
Fixation Time: Set a fixed time, for example, 15:00. The recipient will
receive the system logs sent by the device at 15:00 every day.
Period Time: Set a time interval, for example, 5 hours. The recipient will
receive the system logs sent by the device every 5 hours.
Enable Server
System logs can also be sent to a server. After Auto Mail Feature is enabled, the following content
will be shown.
Figure 7-5 Enable Server
Enter the IP address of the remote server.
Enter the port of the remote server.
System Log Server IP:
System Log Server Port:
Enable Nvram
By default, Nvram is disabled. Check the box to enable Nvram, system logs will be saved after
power supply is cut.
7.2 Web Server
You can log in web management interface, thereby manage and maintain the device.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Following is the page of Web Server.
Figure 7-6 Web Server Page
HTTPS (Hypertext Transfer Protocol Secure) is enabled by default.
HTTPS:
Designate a secure server port for web server in HTTPS mode. By default the
port is 443.
Secure Server
Port:
Designate a server port for web server in HTTP mode. By default the port is 80.
Server Port:
Set the session timeout time. If you do nothing with the web management
page within the timeout time, the system will log out automatically. Please
login again if you want to go back to web management page.
Session
Timeout:
7.3 Management Access
Management Access Control allows you to configure up to four MAC addresses of the hosts that
are allowed to log in to the web management page of the EAP. Click Add PC’s MAC and the MAC
address of the current host will be added to MAC address list.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Following is the page of Management Access.
Figure 7-7 Management Access Page
Check the box to enable MAC Authentication. After MAC Authentication is
enabled, only the PCs in MAC address list can log in the device’s web
management page. By default this function is disabled. All PCs in LAN can log
in and manage the device.
MAC
Authentication:
Enter the MAC addresses of the PCs which are authorized to log in the device.
MAC1~MAC4:
7.4 LED ON/OFF
Following is the page of LED ON/OFF. By default the LED is on.
Figure 7-8 LED ON/OFF
7.5 SSH
This device supports the SSH Server function that allows users to login and manage it through
SSH connection on the SSH client software.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SSH (Secure Shell) is a security protocol established on application and transport layers. SSH-
encrypted-connection is similar to a telnet connection, but essentially the old telnet remote
management method is not safe, because the password and data transmitted with plain-text
can be easily intercepted. SSH can provide information security and powerful authentication
when you login this device remotely through an insecure network environment. It can encrypt
all the transmission data and prevent the information in remote management from being leaked.
Following is the page of SSH.
Figure 7-9 SSH Page
Enter the server port. By default, it is port 22.
Server Port:
SSH Login:
Check the box to enable SSH Server. By default, it is disabled.
7.6 SNMP
The device can be configured as an SNMP agent.
SNMP (Simple Network Management Protocol), the most widely applied network management
protocol, provides a management framework to monitor and maintain Internet devices. Main
functions of SNMP include monitoring network performance, detecting and analyzing network
error, configuring network devices, and so on. When networks function properly, SNMP can
perform the functions of statistics, configuration and testing. When networks have troubles,
SNMP can detect and restore these troubles.
An SNMP consists of three key components: manager, agent and MIB (Management Information
Base). SNMP manager is a client program operating at workstation, assisting network
administrators to accomplish most network device management tasks. An agent is a network-
management software module that resides on a managed device and responsible for receiving
and dealing with data sent by managing device. Generally the managed devices are network
devices including hosts, bridges, switches and routers. MIB is the collection of managed devices.
It defines a series of properties of the managed devices. Every SNMP agent has its own MIB.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Once the device has become an SNMP agent, it is able to receive and process request messages
from SNMP manager.
Following is the page of SNMP.
Figure 7-10 SNMP Page
Enable SNMP Agent and the SNMP Agent will collect the information of this
device and respond to information requests from one or more management
systems.
SNMP Agent:
Enter the textual identification of the contact person for this managed node.
Enter an administratively-assigned name for this managed node.
Enter the physical location of this managed node.
SysContact:
SysName:
SysLocation:
Community refers to a host group aiming at network management. Get
Community only has the read-only right of the device's SNMP information.
The community name can be considered a group password. The default
setting is public.
Get
Community:
Defines the IP address (for example, 10.10.10.1) or subnet for management
systems that can serve as Get Community to read the SNMP information of this
device. The format of subnet is “IP address/bit” (such as 10.10.10.0/24). The
default is 0.0.0.0, which means all hosts can read the SNMP information of this
device.
Get Source:
Set Community has the read and write right of the device's SNMP
information. Enter the community name that allows read/write access to the
device's SNMP information. The community name can be considered a group
password. The default setting is private.
Set Community:
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Defines the IP address (for example, 10.10.10.1) or subnet for management
systems that can serve as Set Community to read and write the SNMP
information of this device. The format of subnet is “IP address/bit” (such as
10.10.10.0/24). The default is 0.0.0.0, which means all hosts can read and write
the SNMP information of this device.
Set Source:
NOTE:
Defining community can allow management systems in the same community to communicate
with the SNMP Agent. The community name can be seen as the shared password of the network
hosts group. Thus, for the security, we suggest modifying the default community name before
enabling the SNMP Agent service. If the field of community is blank, the SNMP Agent will not
respond to any community name.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 System
System page is mainly used to configure some basic information like user account and time, and
realize functions including reboot, reset, backup, restore and upgrade the device.
8.1 User Account
You can change the username and password to protect your device from unauthorized login. We
recommend that you change the default user password on the very first system setup.
Figure 8-1 User Account Page
Enter the present user name and password of the admin account to get the
permission of modification.
Old User
Name/Password:
Enter a new user name and password for the admin account. Both values are
case-sensitive, up to 64 characters and with no space.
New User
Name/Password:
Enter the new password again.
Confirm New
Password:
8.2 Time Settings
System time represents the device system’s notion of the passing of time. System time is the
standard time for Scheduler and other time-based functions. You can manually set the system
time, configure the system to acquire its time settings from a preconfigured NTP server or
synchronize the system time with the PC’s clock.
The device supports DST (daylight saving time).
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 8-2 Time Settings
8.2.1 Time Settings
Figure 8-3 Time Settings
Click the button and the device will obtain GMT time from NTP server. IP
address of the NTP server has to be filled in.
Click the button, your PC’s time will be obtained as the device’s system time.
Select your local time zone from the drop-down list.
Time zone:
Date:
Set the current date, in format MM/DD/YYYY. For example, for November
25, 2014, enter 11/25/2014 in the field.
Specify the device’s time. Select the number from the drop-down list in time
format HH/MM/SS.
Time:
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Primary/Secondary If you’ve selected Get GMT from an NTP server, please input the primary
NTP sever address and an alternative NTP server address.
NTP Server:
8.2.2 Daylight Saving
Figure 8-4 Daylight Saving
Enable or disable the DST. DST is disabled by default.
Daylight Saving:
Mode:
refer to the following content for more information.
Predefined Mode
Figure 8-5 Predefined Mode
Mode:
Select Predefined Mode.
Select a predefined DST configuration. Europe is the predefined country
by default.
Predefine Country:
USA: Second Sunday in March, 02:00 ~ First Sunday in November, 02:00
European: Last Sunday in March, 01:00 ~ Last Sunday in October, 01:00
Australia: First Sunday in October, 02:00 ~ First Sunday in April, 03:00
New Zealand: Last Sunday in September, 02:00 ~ First Sunday in April,
03:00
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Recurring Mode
Figure 8-6 Recurring Mode
Mode:
Select Recurring Mode. The configuration is recurring in use.
Specify the time adding in minutes when Daylight Saving Time comes.
Select starting time and ending time of Daylight Saving Time.
Time Offset:
Start/End:
Date Mode
Figure 8-7 Date Mode
Mode:
Select Date Mode.
Specify the time adding in minutes when Daylight Saving Time comes.
Select starting time and ending time of Daylight Saving Time.
Time Offset:
Start/End:
8.3 Reboot/Reset
Figure 8-8 Reboot & Reset
Click Reboot to restart the device. Click Reset to restore the device to factory default settings.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
8.4 Backup & Restore
Figure 8-9 Backup & Restore
You can save the current configuration of the EAP as a backup file and restore the configuration
via a backup file. Back up the settings before you upgrade the device or upload a new
configuration file can prevent it from being lost.
Restore function helps you to restore the device to previous settings by uploading a backup file.
8.5 Firmware Upgrade
Figure 8-10 Firmware Upgrade
Click Browse to choose the firmware file. Click Upgrade to upgrade the devices.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
1. Please select the proper software version that matches your hardware to upgrade.
2. To avoid damage, please do not turn off the device while upgrading.
3. After upgrading, the device will reboot automatically.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specifications
HARDWARE FEATURES
Model
EAP110
EAP120
EAP220
Interface
Kensington lock slot
RESET button
ETHERNET:
ETHERNET: 10/100/1000Mbps Ethernet port (RJ-
45)
10/100Mbps
Ethernet port (RJ- CONSOLE port (RJ-45)
45) Power connector (DC-2)
Power Supply
24V/1A passive PoE PoE(802.3af-compliant, PoE (802.3af-compliant,
adapter (included) 36-57VDC, 0.2A Max) or 36-57VDC, 0.4A Max)or
external
power supply
4.4W
12VDC/1A external
power supply
9.6W
12VDC/1.5A
Maximum Power 7.7W
Consumption
Antenna
2*3dBi embedded
2*4dBi embedded
Ceiling/Wall mounting (kits included)
CE, FCC, RoHS
4*4dBi embedded
Mounting
Certification
Operating
Temperature
Operating
Humidity
0℃~40℃ (32℉~104℉)
10%~90% non-condensing
WIRELESS FEATURES
Wireless
2.4GHz
2.4GHz & 5GHz
Frequency
Wi-Fi Standard
IEEE 802.11b/g/n
IEEE 802.11a/b/g/n
Up to 600Mbps
Maximum Data Up to 300Mbps
Rate
Max
RF 23dBm
2.4GHz:23dBm
5GHz:20dBm
Transmission
Power
Multiple SSIDs
Up to eight per radio
Captive
Portal Support
Authentication
Wireless Security WEP
WPA/WPA2-personal
WPA/WPA2-enterprise
63
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Targus Mouse Wireless Optical Stow N GoTM Notebook Mouse 30 User Manual
Texas Instruments Car Amplifier TAP6203A1 User Manual
Topcom Blood Pressure Monitor BPM WRIST 2301B User Manual
Toshiba DVD Player SD P1800 User Manual
Toshiba TV DVD Combo 20HLV86 User Manual
Transcend Information Network Card TS0MSM2PC User Manual
Tripp Lite Computer Hardware B132 004 RB User Manual
Vanguard Heating Gas Heater VYS18PWA User Manual
VXI Computer Hardware VM4016 User Manual
Wagner SprayTech Paint Sprayer GM300AC User Manual