UBC69XLT
SCANNER
80 Channels
with 3 band plan
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 2 Friday, September 9, 2005 11:16 AM
Precautions
Before you use this scanner, please read and
observe the following.
EARPHONE WARNING!
Use only a genuine Uniden earphone. An incorrect
earphone may be hazardous to your hearing.
Turn down volume before connecting the earphone
and then adjust volume to suit.
WARNING!
Uniden does not represent this unit to be water-
proof. To reduce the risk of fire or electrical shock,
do not expose this unit to rain or moisture.
Trademarks used throughout this manual are the
property of their respective holders.
Precautions
2
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 3 Friday, September 9, 2005 11:16 AM
UBC69XLT Controls and Display
Antenna
(see “Connecting the
Antenna” on Page 17)
Headphone Jack
Squelch
Volume
Display
Keypad
Power
UBC69XLT Controls and Display
3
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 4 Friday, September 9, 2005 11:16 AM
Contents
Introduction.......................................................... 6
Feature Highlights................................................ 9
About This Manual.......................................... 10
Understanding Scanning ..................................... 11
What is Scanning?.......................................... 11
What is Searching?......................................... 11
Conventional Scanning................................... 11
Where To Obtain More Information ................ 13
Included With Your Scanner................................ 14
Setting Up Your Scanner..................................... 15
Using Internal Batteries................................... 15
Connecting the Antenna ................................. 17
Connecting an Earphone/Headphone............. 18
Connecting an Extension Speaker.................. 18
Attaching the Belt Clip..................................... 19
About Your Scanner ............................................ 20
A Look At The Keypad.................................... 20
A Look At The Display .................................... 23
Operation............................................................. 25
Turning On The Scanner and
Setting Squelch............................................... 25
Storing Known Frequencies Into Channels..... 25
Searching For and Temporarily
Storing Active Frequencies............................. 26
Scanning the Stored Channels ....................... 26
Manually Selecting a Channel ........................ 27
Special Features.................................................. 28
Chain Search .................................................. 28
Search Skip Memory....................................... 31
Delay............................................................... 32
Locking Out Channels..................................... 33
Priority............................................................. 33
Using Keylock ................................................. 34
Using the Display Backlight ............................ 34
Troubleshooting................................................... 35
Resetting the Scanner .................................... 37
Care and Maintenance ........................................ 38
General Use.................................................... 38
Contents
4
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 5 Friday, September 9, 2005 11:16 AM
Location .......................................................... 38
Cleaning.......................................................... 38
Repairs............................................................ 39
Birdies............................................................. 39
Specifications....................................................... 40
Optional Accessories........................................... 42
Declaration of Conformity .................................... 43
Contents
5
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 6 Friday, September 9, 2005 11:16 AM
Introduction
Thank you for purchasing a Uniden UBC69XLT
Handheld Scanner. The scanner is versatile,
compact, and easy to use.
You can program up to 80 frequencies into the
scanner's memory. The scanner lets you scan
transmissions.
Use your scanner to monitor:
•
•
Police
FM CB
This table lists the frequency ranges, default
frequency step, default mode (AM or FM), and type
of transmissions you can hear for each range.
BAND PLAN 1
Frequency Range
(MHz)
Mode Step (kHz) Transmission
25.0000 - 29.9950
30.0000 - 79.9875
80.0000 - 82.9900
83.0000 - 87.2625
FM
FM
FM
FM
5
CB BAND
12.5
10
VHF LOW BAND
VHF LOW BAND
VHF LOW BAND
12.5
12.5
138.0000 - 157.9875 FM
2M AMATEUR
BAND
158.0000 - 160.5900 FM
160.6000 - 162.5875 FM
162.6000 - 173.9900 FM
406.0000 - 439.99375 FM
10
VHF HIGH BAND
VHF HIGH BAND
VHF HIGH BAND
12.5
10
6.25
FederalGov.Land
MOBILE
440.0000 - 465.9950 FM
466.0000 - 469.9900 FM
470.0000 - 512.0000 FM
5
70cm AMATEUR
BAND
10
6.25
UHF STANDARD
BAND
UHF "T" BAND
Introduction
6
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 7 Friday, September 9, 2005 11:16 AM
BAND PLAN 2
Frequency Range
(MHz)
Mode Step (kHz) Transmission
25.0000 - 84.0100
84.0150 - 87.2550
FM
FM
5
CB BAND
20
5
VHF LOW BAND
137.0000 - 143.9950 FM
MILITARY LAND
MOBILE
144.0000 - 145.9875 FM
12.5
2M AMATEUR
BAND
146.0000 - 155.9900 FM
156.0000 - 162.0250 FM
10
VHF HIGH BAND
12.5
VHF MARINE
BAND
162.0300 - 173.9900 FM
406.0000 - 439.99375 FM
440.0000 - 449.99375 FM
10
VHF HIGH BAND
UHF LOW BAND
6.25
6.25
70cm AMATEUR
BAND
450.0000 - 469.9900 FM
470.0000 - 512.0000 FM
10
UHF STANDARD
BAND
6.25
UHF "T" BAND
Introduction
7
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 8 Friday, September 9, 2005 11:16 AM
BAND PLAN 3
Frequency Range
(MHz)
Mode Step (kHz) Transmission
25.0000 - 29.9950
30.0000 - 79.9950
80.0000 - 82.9950
83.0000 - 87.2650
FM
FM
FM
FM
5
5
5
5
5
CB BAND
VHF LOW BAND
VHF LOW BAND
VHF LOW BAND
138.0000 - 157.9950 FM
2M AMATEUR
BAND
158.0000 - 160.5950 FM
160.6000 - 162.5950 FM
162.6000 - 173.9950 FM
406.0000 - 439.99375 FM
5
VHF HIGH BAND
VHF HIGH BAND
VHF HIGH BAND
5
5
6.25
FederalGov.Land
MOBILE
440.0000 - 465.99375 FM
466.0000 - 469.99375 FM
470.0000 - 512.0000 FM
6.25
6.25
6.25
70cm AMATEUR
BAND
UHF STANDARD
BAND
UHF "T" BAND
To select band plan from 1, 2 and 3;
1. Make sure the power is turned off
2. While holding down 1, 2 or 3 (the number
corresponding to the band plan), turn on the
scanner.
Note: Please reset the scanner (see page 37) after
band plan was changed.
Introduction
8
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 9 Friday, September 9, 2005 11:16 AM
Feature Highlights
Chain Search - lets you enter personal search bands
in 5 locations and search all locations in a chain of
frequency bands.
Triple-Conversion Circuitry - virtually eliminates
any interference from IF (intermediate frequency)
images, so you hear only the selected frequency.
Two-Second Scan Delay - delays scanning for about 2
seconds before moving to another channel, so you can
hear more replies that are made on the same channel.
Lock-Out Function - lets you set your scanner to
skip over specified channels or frequencies when
scanning or searching.
Priority Channels - lets you program one channel
and then have the scanner check that channel every
2 seconds while it scans, so you do not miss
transmissions on the channel.
Key Lock - lets you lock the scanner's keys to help
prevent accidental changes to the scanner's
programming.
Direct Access - lets you directly access any
channel.
Display Backlight - makes the scanner easy to
read in low-light situations.
Flexible Antenna with BNC Connector - provides
adequate reception in strong signal areas and is
designed to help prevent antenna breakage.
Or, you can connect an external antenna for better
reception.
Memory Backup - keeps the frequencies stored in
memory for an extended time if the scanner loses
power.
Feature Highlights
9
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 10 Friday, September 9, 2005 11:16 AM
Key Confirmation Tones - the scanner sounds a
tone when you perform an operation correctly, and
an error tone if you make an error.
Battery Low Alert - warns you when battery power
gets low.
About This Manual
The screen displays used in this manual are
representations of what might appear when you use
your scanner. Since what you see depends on the
frequencies for your area and the settings you select,
you might notice some differences between what is
in this manual and what appears on your scanner.
To get the most from this manual, review the
contents to become familiar with the basic functions
available. If you are new to scanning, be sure to
read “Understanding Scanning” on Page 11 for a
quick background on the technology behind the
hobby. The first thing you’ll need to do is install
batteries in the scanner. Then you need to connect
the included antenna to the scanner. See “Using
Internal Batteries” on Page 15 and “Connecting the
Antenna” on Page 17 if you need any help doing this.
Feature Highlights
10
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 11 Friday, September 9, 2005 11:16 AM
Understanding Scanning
This section provides you with background on how
scanning works. You don’t really need to know all of
this to use your scanner, but some background
knowledge will help you get the most from your
UBC69XLT.
What is Scanning?
Unlike standard AM or FM radio stations, most two-
way communications do not transmit continuously.
Your UBC69XLT scans programmed channels until
it finds an active frequency, then stops on that
frequency and remains on that channel as long as
the transmission continues. When the transmission
ends, the scanning cycle resumes until the scanner
receives another transmission.
What is Searching?
The UBC69XLT can search for active frequencies.
This is different from scanning because you are
searching for frequencies that have not been
programmed into the scanner. When you select
frequency bands to search, the scanner searches
for any active frequency within the lower and upper
limits you specify. When the scanner finds an active
frequency, it stops on that frequency as long as the
transmission lasts. If you think the frequency is
interesting, you can program it into one of the banks.
If not, you can continue to search.
Conventional Scanning
Conventional scanning is a relatively simple concept.
Each group of users in a conventional system is
assigned a single frequency (for simplex systems) or
two frequencies (for repeater systems). Any time one
of them transmits, their transmission always goes
out on the same frequency. Up until the late 1980’s
Understanding Scanning
11
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 12 Friday, September 9, 2005 11:16 AM
this was the primary way that radio systems
operated.
Even today, there are many 2-way radio users who
operate using a conventional system:
•
•
•
•
•
Aircraft
Amateur radio
PMR users
Broadcast AM/FM/TV stations
Many business radio users
When you want to store a conventional system, all
you need to know is the frequencies they operate
on. When you are scanning a conventional system,
the scanner stops very briefly on each channel to
see if there is activity. If there isn’t, the scanner
quickly moves to the next channel. If there is, then
the scanner pauses on the transmission until it is over.
Simplex Operation
Simplex systems use a single frequency for both
transmit and receive. Most radios using this type of
operation are limited to line-of-sight operation. This
type of radio is frequently used at construction job
sites, and with inexpensive consumer radios such as
PMR radios. The range is typically 1.5-12 km,
depending upon the terrain and many other factors.
Repeater Operation
Repeater systems use two frequencies: one transmits
from the radio to a central repeater; the other
transmits from the repeater to other radios in the
system. With a repeater-based system, the repeater
is located on top of a tall building or on a radio tower
that provides great visibility to the area of operation.
When a user transmits (on an input frequency), the
signal is picked up by the repeater and retransmitted
(on an output frequency). The user’s radios always
Understanding Scanning
12
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 13 Friday, September 9, 2005 11:16 AM
listen for activity on the output frequency and
transmit on the input frequency. Since the repeater
is located very high, there is a very large line of
sight. Typical repeater systems provide coverage
out to about a 40 km radius from the repeater
location.
Where To Obtain More Information
By itself, this manual really only provides part of
what you need to know to have fun scanning – how
to program and use the scanner.
Information On The Internet
The Internet is a great source for current frequencies
and information about scanning.
Many web sites have lists of frequencies for your area.
You can use a search engine to find and use them.
Make a list of the agencies you want to listen to,
then look up the frequencies and systems used by
those agencies.
Understanding Scanning
13
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 14 Friday, September 9, 2005 11:16 AM
Included With Your Scanner
UBC69XLT
SCANNER
80 Channels
with
3
band plan
Belt Clip
Owners Manual
Scanner and
Antenna
Note: If any of these items are missing or damaged,
contact your place of purchase.
Included With Your Scanner
14
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 15 Friday, September 9, 2005 11:16 AM
Setting Up Your Scanner
These guidelines will help you install and use your
new scanner:
•
If your scanner receives interference or electrical
noise, move the scanner or its antenna away
from the source.
•
To improve the scanner’s reception, use an
optional external antenna designed for multi-
band coverage. (You can purchase this type of
antenna at a local electronics store). If the
optional antenna has no cable, use 50-70 ohm
coaxial cable for lead-in. A mating plug might be
necessary for the optional antennas.
•
•
Use an optional mono earphone or mono
headset with proper impedance for private
listening. Read the precautions on the inside
front cover of this Owners Manual.
Do not use the scanner in high-moisture
environments such as the kitchen or bathroom.
• Avoid placing the scanner in direct sunlight or
near heating elements or vents.
Using Internal Batteries
You can power your scanner using two AA batteries
(not supplied).
1. Make sure the power is turned off.
2. Slide the battery compartment cover.
Setting Up Your Scanner
15
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 16 Thursday, September 15, 2005 2:20 PM
3. Install two batteries in the compartment as
indicated by the polarity symbols (+ and -)
marked inside.
4. Replace the cover.
Cautions:
•
•
•
Use only fresh batteries of the required size and
recommended type.
When
flashes and the scanner beeps
every 15 seconds, replace both batteries.
Always remove old or weak batteries. Batteries
can leak chemicals that destroy electronic
circuits.
Setting Up Your Scanner
16
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 17 Thursday, September 15, 2005 2:20 PM
•
•
Do not mix old and new batteries, different types
of batteries (standard, alkaline, or rechargeable),
or rechargeable batteries of different capacities.
If you use rechargeable batteries instead of
alkaline batteries, make sure they are fully
charged.
Connecting the Antenna
To attach the supplied flexible antenna to the
connector on the top of your scanner, align the slots
around the antenna's connector with the tabs on the
scanner's BNC connector. Then slide the antenna's
connector down over the scanner's connector and
rotate the antenna connector's outer ring clockwise
until it locks into place.
Connecting an Optional Antenna
The scanner's BNC connector makes it easy to
connect a variety of optional antennas, including an
external mobile antenna or outdoor base station
antenna.
Setting Up Your Scanner
17
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 18 Thursday, September 15, 2005 2:20 PM
Note: Always use 50-ohm, RG-58, or RG-8, coaxial
cable to connect an outdoor antenna. If the antenna
is over 15 metres from the scanner, use RG-8 low-
loss dielectric coaxial cable. You can get a BNC
adapter at your local electronics store.
Connecting an Earphone/Headphone
UBC72XLT
For private listening, you can plug a 3.5 mm mini-
plug earphone or mono headphones (not supplied)
into the headphone jack on top of your scanner. This
automatically disconnects the internal speaker.
Connecting an Extension Speaker
In a noisy area, an optional extension speaker,
positioned in the right place, might provide more
comfortable listening. Plug the speaker cable's 3.5-
mm mini-plug into your scanner's jack.
WARNING!
If you connect an external speaker to the scanner's
headphone jack, never connect the audio output line
to a power supply and ground. This might damage
the scanner.
Setting Up Your Scanner
18
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 19 Friday, September 9, 2005 11:16 AM
Attaching the Belt Clip
To make your scanner easier to carry when you are
on the go, use the supplied belt clip. Use a Phillips
screwdriver and the supplied screws to attach the
clip to the scanner.
Setting Up Your Scanner
19
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 20 Friday, September 9, 2005 11:16 AM
About Your Scanner
We use a few simple terms in this manual to explain
the features of the scanner. Familiarize yourself with
these terms and the scanner's features, and you can
put the scanner to work for you right away. Simply
determine the type of communications you want to
receive, then set the scanner to scan those
communications.
A frequency, expressed in kHz or MHz, is the tuning
location of a station. To find active frequencies, you
use the search function or refer to a frequency
reference.
When you search and find a desired frequency, you
can store it into a programmable memory location
called a channel. You can scan the channels if there
are any activities on the frequencies stored there.
A Look At The Keypad
Your scanner's keys have various functions labeled
on the key tops and below the keys.
To select the function labeled on a key, simply press
the key. To select the function labeled below a key,
first press Func then release it.
appears on the
F
display. Then press the next key in the function key
sequence while appears. appears or
F
F
disappears as you press Func.
About Your Scanner
20
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 21 Friday, September 9, 2005 11:16 AM
If your scanner's keys seem confusing at first, the
following information should help you understand
each key's function.
Key Name
Hold
Description
Hold – Holds the scan or the
frequency search. Press and
hold Hold to increment
channels continuously.
Scan/Src
Scan – Scans the stored
channels.
Func + Src – Starts chain
search or resumes searching.
/
– Turns the display
backlight on or off.
Func +
– Locks and
unlocks the keypad.
Func
Lets you use various functions
by pressing this key in
combination with other keys.
Press and hold for more than
2 seconds to turn the scanner
on or off.
1/Pri
2/
1 – Enters a 1.
Func + Pri – Sets and turns the
priority function on or off.
2 – Enters a 2.
Func +
– Selects the search
direction.
3
3 – Enters a 3.
About Your Scanner
21
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 22 Friday, September 9, 2005 11:16 AM
Key Name
4
Description
4 – Enters a 4.
5 – Enters a 5.
5/Dly
Func + Dly – Sets and turns the
delay function on or off.
6/PSrc
6 – Enters a 6.
Func + PSrc – Sets and turns
program band select mode on
or off.
7
7 – Enters a 7.
8 – Enters an 8.
8/
Func +
– Selects the search
direction.
9
Enters a 9.
/Clr
– Enters a decimal point.
Clr – Clears a frequency you
entered by mistake.
0/L/O
0 – Enters a 0.
Func + L/O – Lets you lock out
a selected channel or skip a
specified frequency.
E/Pgm
E – Enters frequencies into
channels.
Func + Pgm – Lets you
program the frequency.
About Your Scanner
22
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 23 Friday, September 9, 2005 11:16 AM
A Look At The Display
The display has indicators that show the scanner's
current operating status. The display information
helps you understand how your scanner operates.
BANK- appears with numbers (1-5).
- appears when you lock the keypad.
F
- appears only when the function mode is on.
PGM
- appears while you store a frequency into a
channel.
SRCH- appears during search mode.
or - appears during search mode.
- alerts you when the battery power gets low.
P- appears when you select a priority channel.
SCN- appears when you scan channels.
HOLD- appears during scan hold mode and search
hold mode.
About Your Scanner
23
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 24 Friday, September 9, 2005 11:16 AM
L/O- appears when you manually select a channel
you locked out or a skip frequency.
DLY- appears when you select a delay.
PRI- appears when the priority feature is turned on.
About Your Scanner
24
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 25 Friday, September 9, 2005 11:16 AM
Operation
Turning On The Scanner and
Setting Squelch
Note: Make sure the scanner's antenna is
connected before you turn it on.
1. Turn Squelch fully counterclockwise.
2. Press and hold
for about 2 seconds to turn
the scanner on, then turn Volume clockwise until
you hear a hissing sound.
3. If the scanner is scanning, press Hold to stop
scanning, then turn Squelch clockwise until the
hissing stops.
Storing Known Frequencies
Into Channels
1. Press Hold. Then enter the channel number
where you want to store a frequency, then press
Func and Pgm. The channel number appears.
2. Use the number keys and /Clr to enter the
frequency (including the decimal point) you want
to store.
3. Press E to store the frequency into the channel.
Notes:
•
If you entered an invalid frequency in Step 2,
Errorappears and the scanner beeps three
times. Enter a valid frequency.
•
The scanner automatically rounds the entered
number to the nearest valid frequency.
For example, if you enter 28.473. (MHz), your
scanner accepts it as 28.475.
•
When you enter a frequency into a channel, the
scanner automatically turns on the delay
function and DLYappears. When delay is turned
on, the scanner automatically pauses scanning
Operation
25
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 26 Friday, September 9, 2005 11:16 AM
2 seconds after the end of a transmission before
scanning proceeds to the next channel. To turn
the function off or on, press Func + Dly.
•
If you enter a frequency that has already been
entered elsewhere, the scanner sounds an error
tone and displays the channel that was
duplicated. If you entered the frequency by
mistake, press Clr then enter the correct
frequency. To enter the frequency anyway, press
E to accept.
4. To program the next channel in sequence, press
E/Pgm then repeat Steps 2 and 3.
Searching For and Temporarily
Storing Active Frequencies
If you do not have a reference to frequencies in your
area, use a search to find a transmission.
Note: When the scanner starts searching, it auto-
matically turns on the delay function. To turn delay
on or off, press Func + Dly.
Scanning the Stored Channels
To begin scanning channels, press Scan.
The scanner scans through all non-locked channels
(See “Locking Out Channels” on Page 33). When
the scanner finds a transmission, it stops on it.
When the transmission ends, the scanner resumes
scanning.
Operation
26
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 27 Friday, September 9, 2005 11:16 AM
Notes:
•
If you have not stored frequencies into any
channels, the scanner does not scan.
•
If the scanner picks up unwanted partial, or very
weak transmissions, turn Squelch clockwise to
decrease the scanner's sensitivity to these
signals. To listen to a weak or distant station,
turn Squelch counterclockwise.
•
To ensure proper scanning, adjust Squelch until
the audio mutes.
Manually Selecting a Channel
You can continuously monitor a single channel
without scanning. This is useful if you hear an
emergency broadcast on a channel and do not want
to miss any details - even though there might be
periods of silence - or if you want to monitor a
specific channel.
To manually select a channel, press Hold, enter the
channel number then press Hold again.
Or, during scanning, if the radio stops at a channel
you want to listen to, press Hold once. (Repeatedly
pressing Hold at this time causes the scanner to
step through the channels.) Press Scan to resume
automatic scanning.
Operation
27
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 28 Friday, September 9, 2005 11:16 AM
Special Features
Chain Search
This feature lets you search through preset
frequency ranges. You can also change each range
to a range you set. There are three modes within
this feature: chain search mode, chain search hold
mode, and program band select mode.
The preset frequency ranges are:
BAND PLAN 1
Bank Frequency (MHz)
No.
Step (kHz)
1
2
3
4
5
30.0000 - 79.9875
83.0000 - 87.2625
160.6000 - 162.5875
440.0000 - 465.9950
466.0000 - 469.9900
12.5
12.5
12.5
5
10
BAND PLAN 2
Bank Frequency (MHz)
No.
Step (kHz)
1
2
3
4
5
84.0150 - 87.2550
20
144.0000 - 145.9875
156.0000 - 162.0250
162.0300 - 173.9900
406.0000 - 439.99375
12.5
12.5
10
6.25
Special Features
28
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 29 Friday, September 9, 2005 11:16 AM
BAND PLAN 3
Bank Frequency (MHz)
No.
Step (kHz)
1
2
3
4
5
25.0000 - 29.9950
5
5
160.6000 - 162.5950
162.6000 - 173.9950
440.0000 - 465.99375
466.0000 - 469.99375
5
6.25
6.25
See page 8 for how to switch the band between 1, 2
and 3.
Chain Search Mode
Press Func + Src to start chain search mode. SRCH,
the enabled search bank number, and or
(indicating the search direction) appear. The search
bank number being searched flashes.
Press 1-5 to enable or disable the search bank
number being searched in this mode. Enabled bank
numbers appear. (Disabled bank numbers
disappear).
At least one search bank must be enabled. (The
scanner sounds an error tone if you try to disable all
the search banks). The search bank and the
frequency where chain search starts depends on
how the scanner was set before you selected chain
search mode.
Chain Search Hold Mode
To start chain search hold mode, press Hold in
chain search mode. The scanner stops searching
and Holdappears. In this mode, pressing
Func +
and pressing Func +
changes the search direction downward
changes the search
Special Features
29
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 30 Friday, September 9, 2005 11:16 AM
direction upward. or appears according to the
current search direction.
Storing Frequencies Found During
Chain Search into Channel Memory
You can store frequencies you find in chain search
mode or chain search hold mode.
1. Press Func + Pgm in chain search mode or
chain search hold mode. The lowest blank
channel appears.
2. Press E/Pgm to store the frequency into the
blank channel. To select another channel, press
Func +
or Func +
before you press
E/Pgm.
If you try to save a frequency that is already stored,
the scanner sounds an error tone and displays the
channel that was duplicated. If you entered the
frequency by mistake, press /Clr. To enter the
frequency anyway, press E to accept.
The scanner sets itself to program mode after you
store a frequency.
Setting the Search Range
You can use this mode to define the search range
used during a search in each search bank. To
change a search range, press Func and PSrc.
SRCHappears. Then select a search bank.
When you select the search bank, the lower limit
and upper limit frequency assigned in the search
bank alternate on the display.
To select another search bank, press Func + PSrc
or Func +
or Func +
to increase the search bank number
to decrease it. Hold down Func + or
Special Features
30
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 31 Friday, September 9, 2005 11:16 AM
Func +
for about 1 second to quickly move
through the search bank numbers.
After choosing the search bank, follow these steps
to set the lower limit and upper limit frequency.
1. Enter the lower limit frequency by using the 0-9
and /Clr keys.
2. Press E to select the lower limit frequency.
3. Enter the upper limit frequency by using the 0-9
and /Clr keys.
4. Press E to select the upper limit frequency.
Search Skip Memory
You can skip up to 50 specified frequencies during a
search. This lets you avoid unwanted frequencies or
those already stored in a channel.
To skip a frequency, press Func and L/O when the
scanner stops on the frequency during a search or a
search hold. The scanner stores the frequency in
memory and automatically resumes the search if it is
not in hold.
Follow these steps to clear a single frequency from
skip memory so the scanner stops on it during a
search.
1. Press Hold to stop the search.
2. Press Func +
or Func +
to select the
frequency. L/Oappears.
3. Press Func + L/O. L/Odisappears.
To clear all the skip frequencies at once while
searching or search hold, press Func then press
and hold L/O until the scanner beeps.
Special Features
31
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 32 Friday, September 9, 2005 11:16 AM
Notes:
•
If you selected all frequencies to be skipped
within the search range, the scanner beeps 3
times and does not search.
•
If you select more than 50 frequencies to skip,
each new frequency replaces a frequency
previously stored, beginning with the first stored
frequency.
•
Press Func +
or Func +
to select a
skipped frequency while Holdappears. L/O
appears when you select a skipped frequency.
Delay
Sometimes a user might pause before replying to a
transmission. To avoid missing a reply on a specific
channel, you can program a 2-second delay into any
channel or frequency. The scanner continues to
monitor the channel frequency for an additional
2 seconds after the transmission stops before
resuming scanning or searching. The scanner
automatically sets a delay when you store
frequencies into channels or when you search
frequencies. When the delay feature is on, DLY
appears. If it is off, follow one of these steps to
program a delay depending on how the scanner is
operating,.
•
If the scanner is scanning and stops on an active
channel where you want to store a delay, quickly
press Func + Dly before it continues scanning
again. DLYappears.
•
If the desired channel is not selected, manually
select the channel, then press Func + Dly. DLY
appears.
Special Features
32
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 33 Friday, September 9, 2005 11:16 AM
•
If the scanner is searching, press Func + Dly
while the scanner is searching. DLYappears and
the scanner automatically adds a 2-second
delay to every frequency it stops on in that band.
To turn off the 2-second delay, press Func + Dly
while the scanner is monitoring a channel, scanning,
or searching. DLYdisappears.
Locking Out Channels
You can increase the scanning speed by locking out
channels that have a continuous transmission.
To lock out a channel, manually select the channel,
then press Func + L/O. L/Oappears.
Note: You can still manually select locked-out
channels.
To remove the lockout from a channel, manually
select the channel, then press Func + L/O.
L/Odisappears.
To unlock all channels, press Hold to stop scanning,
then press Func and press and hold L/O until the
scanner beeps twice.
Priority
The priority feature lets you scan through the
channels and still not miss important or interesting
calls on specific channel. You can program one
stored channel as a priority channel.
If the priority feature is turned on, as the scanner
scans channels, it checks priority channel for activity
every 2 seconds.
The scanner automatically designates first channel
as its priority channel.
Special Features
33
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 34 Friday, September 9, 2005 11:16 AM
Follow these steps to select a different channel as
the priority channel.
1. Manually select the channel you want to select
as the priority channel.
2. Press Func + Pgm, then press Func + Pri.
P appears to the left of the selected channel
number.
To turn on the priority feature, press Func + Pri
during scanning. PRIappears. Then the scanner
checks the designated priority channel every
2 seconds.
To turn off the priority feature, press Func + Pri.
PRI disappears.
Using Keylock
Use the scanner's keylock to protect it from
accidental program changes. When the scanner's
keys are locked, the only controls that operate are
Scan, Func, Hold,
,
, and
.
To turn on keylock, press Func +
To turn off keylock, press Func +
disappears.
.
.
appears.
Note: Using keylock does not prevent the scanner
from scanning channels.
Using the Display Backlight
To turn on the display light for easy viewing at night,
press . The display lights for 15 seconds. To turn
off the light sooner, press
again.
Special Features
34
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 35 Friday, September 9, 2005 11:16 AM
Troubleshooting
If your UBC69XLT is not performing properly, try the
following steps.
Problem
The
scanner
doesn’t
work.
Possible Cause
The scanner
might not be
receiving any
power.
Suggestion
Check the batteries.
Improper
The scanner’s Check the antenna
reception. antenna might connection or move
need to be
adjusted.
or reposition the
antenna.
Move the scanner.
You might be in a
remote area that
could require an
optional multi-band
antenna. Check
with your dealer or
local electronics
store.
Scan
won’t
stop.
The squelch
might need to
be adjusted.
Adjust the squelch
threshold. See
“Turning On The
Scanner and
Setting Squelch” on
Page 25.
The antenna
might need to
be adjusted.
Check the antenna
connection.
One or more
Make sure the
channelsmight channels you want
be locked out. to scan are not
locked out.
Troubleshooting
35
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 36 Friday, September 9, 2005 11:16 AM
Scan
The channel’s
Make sure the
channel’s
frequency is stored
in the scanner’s
memory.
won’t stop frequency
(continued) might not be
stored in
memory.
The channel
might not be
active.
Wait for a
transmission on the
channel.
Scan
won’t
start.
You must
press Scan to
scan.
Press Scan.
The squelch
might need to
be adjusted.
Adjust the squelch
threshold. See
“Turning On The
Scanner and
Setting Squelch” on
Page 25.
One or more
Make sure the
channelsmight channels you want
be locked out. to scan are not
locked out.
The antenna
might need to
be adjusted.
Check the antenna
connection.
Troubleshooting
36
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 37 Friday, September 9, 2005 11:16 AM
Resetting the Scanner
If the scanner's display locks up or stops operating
properly, you might need to reset the scanner.
Caution: This procedure clears all the information
(except the band plan data) you have stored in the
scanner. Before you reset the scanner, try turning it
off and on to see if it begins working properly. Reset
the scanner only when you are sure it is not working
properly.
1. Turn off the scanner.
2. While holding down 2, 9, and Hold, turn on the
scanner. It takes about 3 seconds to initialize
and CLEArappears.
Troubleshooting
37
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 38 Friday, September 9, 2005 11:16 AM
Care and Maintenance
Keep the scanner dry. If it gets wet, wipe it dry
immediately. Use and store the scanner only in
normal temperature environments. Handle the
scanner carefully: do not drop it. Keep the scanner
away from dust and dirt, and wipe it with a damp
cloth occasionally to keep it looking new.
General Use
•
•
•
Turn the scanner off before disconnecting the
power.
Always write down the programmed frequencies
in the event of memory loss.
If memory is lost, simply reprogram each
channel. The display shows 000.000in all
channels when there has been a memory loss.
•
Always press each button firmly until you hear
the entry tone for that key entry.
Location
•
•
•
Do not use the scanner in high-moisture
environments such as the kitchen or bathroom.
Avoid placing the unit in direct sunlight or near
heating elements or vents.
If the scanner receives strong interference or
electrical noise, move it or its antenna away from
the source of the noise. If possible, a higher
elevation might provide better reception.
•
Also try changing the height or angle of the
antenna.
Cleaning
•
Disconnect the power to the unit before
cleaning.
Care and Maintenance
38
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 39 Friday, September 9, 2005 11:16 AM
•
•
Clean the outside of the scanner with a mild
detergent.
To prevent scratches, do not use abrasive
cleaners or solvents. Be careful not to rub the
LCD window.
•
Do not use excessive amounts of water.
Repairs
Do not attempt any repair. The scanner contains no
user serviceable parts.
Birdies
All radios can receive “birdies” (undesired signals). If
your scanner stops during Scan mode and no sound
is heard, it might be receiving a birdie. Birdies are
internally generated signals inherent in the
electronics of the receiver.
Press L/O to lock out the channel, then press Scan
to resume scanning.
If you still cannot get satisfactory results while using
your scanner or if you want additional information,
please call or write the Uniden Parts and Service
Division. The address and phone number are listed
in the Warranty at the end of this manual.
Care and Maintenance
39
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 40 Friday, September 9, 2005 11:16 AM
Specifications
Specifications
Channels: ............................................................. 80
Frequency Range (in MHz):
Sensitivity (SINAD 12 dB)
See page 6 and 8
25.005 MHz (FM) .........................................0.3 µV
54.050 MHz (FM) .........................................0.3 µV
86.275 MHz (FM) .........................................0.3 µV
138.150 MHz (FM).........................................0.3 µV
162.400 MHz (FM) ........................................0.3 µV
173.220 MHz (FM) ........................................0.3 µV
406.875 MHz (FM).........................................0.4 µV
453.250 MHz (FM) ........................................0.4 µV
511.9125 MHz (FM) ......................................0.4 µV
Operating Temperature:
Normal ........................................... –20°C to +60°C
Scan Rate: ...............50 channels per second (max)
Search Rate
Normal ..........................60 steps per second (max)
Hyper ...........................180 steps per second (max)
Priority Sampling ......................................2 seconds
Scan Delay: .............................................2 seconds
IF Rejection (at 162.4 MHz) ............................90 dB
IF Frequencies
1st IF (25-173.99 MHz).....380.6050-380.7000 MHz
1st IF (406-512 MHz) .....380.60625-380.7000 MHz
2nd IF .......................................................21.3 MHz
3rd IF ......................................................... 450 kHz
Audio Output .............................. 400 mW maximum
Built-in Speaker ............................32 mm dia, 8 ohm
Dynamic Type
Current Drain
Squelched ....................................................90 mA
Full Output ..................................................290 mA
Specifications
40
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 41 Friday, September 9, 2005 11:16 AM
Power Requirements:
2 AA Alkaline Batteries (3V DC),
or 2 AA Rechargeable Ni-MH Batteries (2.4V DC)
Antenna: ............................... 50 ohms (Impedance)
External Jacks: ................. Antenna Jack BNC Type
Ext. Speaker Jack 3.5mm
Size: ............ 68mm (W) x 31.5mm (D) x 115mm (H)
Weight: ............................................................ 165 g
Features, specifications, and availability of optional
accessories are all subject to change without notice.
Specifications
41
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 42 Friday, September 9, 2005 11:16 AM
Optional Accessories
Þ
Earphone
External Speaker
Optional Accessories
42
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 43 Friday, September 9, 2005 11:16 AM
Declaration of Conformity
We:
Uniden Corporation
2-12-7 Hatchobori
Chuo-Ku, Tokyo 104-8512
Japan
declare, under our sole responsibility, that this
equipment “Uniden Bearcat model UBC69XLT” is in
compliance with the essential requirements and
other relevant provisions of the EMC, R&TTE and
LVD Council Directives of the EU.
Declaration of Conformity
43
Download from Www.Somanuals.com. All Manuals Search And Download.
UB334 Paper OM reduced size.fm Page 44 Friday, September 9, 2005 11:16 AM
COVERED UNDER ONE OR MORE OF THE FOLLOWING
U.S. PATENTS:
4,398,304
4,597,104
4,947,456
5,438,688
5,548,296
5,598,430
5,896,422
6,034,573
4,409,688
4,627,100
5,014,348
5,448,256
5,530,296
5,600,223
5,991,346
6,064,270
4,455,679
4,841,302
5,199,109
5,465,402
5,571,071
5,642,424
5,991,603
6,266,521
4,461,036
4,888,815
5,408,692
5,471,660
5,574,995
5,710,992
6,012,158
4,521,915
4,932,074
5,428,826
5,483,684
5,577,076
5,859,875
6,025,758
© 2005 Uniden Corporation.
UBZZ01334ZZ(0)
All rights reserved.
Printed in P.R.C.
Download from Www.Somanuals.com. All Manuals Search And Download.
|