™
Installation Guide
CO2075FF —
Ice Maker/Refrigerator
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696
©2005 U-Line Corporation
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
General Precautions
2 Inspect and Plan
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
You have received a carton containing your CO2075FF
Ice Maker/Refrigerator with a package inside
containing a User Manual, a Product Registration
Card and water connection parts. Complete and mail
the Product Registration Card or register online at
keep the User Manual and this Installation Guide in a
safe place for future reference.
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Keep the unit unplugged throughout installation
except during testing.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
Your unit is Black, White or Stainless Steel. Black and
White units have a reversible door with a slightly
contoured handle across the top. They come with a flush
mounted door panel that, when removed, will accept a
custom 1/4-inch thick door panel or a 3/4-inch thick full
overlay door panel. Stainless Steel units are covered with
a protective coating and have been ordered left- or right-
hand hinged. The Stainless doors are not reversible and do
not accept custom panels. Please carefully follow the
directions that apply to your unit and your intended design.
• Never use an extension cord to connect power to
the unit.
• Always keep your working area dry.
CAUTION
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp edges.
Tools/Materials Required
• 7/64" Allen wrench
• Do not lift the unit by the door or door handle.
• Do not install the unit behind closed doors or in any
way that would obstruct airflow to the front grille,
which may cause the unit to malfunction.
• Screwdrivers — slotted and Phillips head
• 1/4-inch OD copper tubing and shut-off valve for water
supply line
• 1/4-inch thick door panel material and cutting tools
(Black or White units)
• Full Overlay Door Panel Kit (part number U-OL2075B —
Black or part number U-OL2075W — White), 3/4-inch
door panel overlay, cutting tools, drill and bits (Black or
White units)
Inspection
Unwrap and inspect the unit on a flat, level surface
capable of supporting its entire weight.
Removing Protective Coating
(Stainless Steel Units Only)
When inspecting/installing a Stainless Steel unit, the
protective coating covering the unit must be removed
first. Start at a corner of the unit/door and pull back the
protective coating to remove it from the unit/door.
02/2005
3
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
After all the protective coating has been removed from
3 Prepare Site
the unit/door, clean all Stainless Steel surfaces with Claire
Stainless Steel Polish and Cleaner or comparable product
or a mild detergent and warm water solution and soft
cloth. Do NOT use abrasive cleaning agents.
Your U-Line product has been designed for either free-
standing or built-in installation. When built-in, your unit
does not require additional air space for top, sides or rear.
However, the front grille must NOT be obstructed and
clearance is required for water, drain and electrical
connections in the rear.
Note: If cleaning with mild detergent and warm water
solution and soft cloth, the unit MUST be treated with
Claire Stainless Steel Polish and Cleaner or comparable
product to prevent discoloration.
Note: Unit can NOT be installed behind a closed cabinet
door.
Exterior Cleaning
(As Required)
Cut-Out Dimensions
Black and White Models:
• The door, grille and cabinet may be cleaned with a mild
detergent and warm water solution. Do not use
solvent-based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
See Electrical
Specifications
for Power Supply
Stainless Steel Models:
23-11/16"
• Stainless steel models can discolor when exposed to
chlorine gas, pool chemicals, salt water or cleaners with
bleach.
34-1/4"
to
35-1/8"
• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
polish on a monthly basis. For best results use Claire
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation. (The part number
is 173348.) Comparable products are acceptable.
Frequent cleaning will remove surface contamination
that could lead to rust. Some installations may require
cleaning on a weekly basis.
8"
24-3/16"
Figure 1
width allows 1/4" for ease in installation and removal of
the unit. 24" is the counter depth in most installations.
The unit is 23-11/16" deep including the handle
on Black and White models and 23-11/16" deep including
the door and not the handle on Stainless Steel models
• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically
intended for stainless steel (this includes glass,
tile and counter cleaners).
• If any surface discolors or rusting appears, clean it
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Use of abrasive pads such as Scotchbrite will
cause the graining in the stainless to become
blurred.
• Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
4
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
Product Dimensions
Reversing the Door
(Black and White Units Only)
23-11/16"
Including
Handle
25-13/16"
Including
Handle
All U-Line units (except
Stainless Steel models) may
be left- or right-hand
opening. The door opening is
easily reversed by moving the
hinge hardware to the
opposite side. The top hinge
hardware will be used on the
bottom of the other side and
the bottom hinge hardware
will be used on the top of the
34-1/8"
34-1/8"
4
3
1
5
7
2
6
23-15/16"
Black and White
23-15/16"
Stainless Steel
To reverse the door:
WARMER
COLDER
1. Remove top hinge screw
pin from door (7/64" Allen
wrench or Phillips
Figure 4
Figure 2
screwdriver, depending on your unit’s construction) (see
off bottom hinge pin.
Please note that the unit has adjustable feet that can add
one additional inch to height during leveling or to match
2. Remove plastic screw plugs (3 each, top and bottom)
Door Swing/Clearances Information
Black and White units have a zero clearance for the door
a minimum of 2-1/8" door clearance to accommodate the
handle if the unit is installed next to a wall or similar type
of structure.
Screw Plugs
Wall
Wall
2-1/8" Min.
1/4" Min.
Figure 5
Figure 6
21-7/16"
25-1/2"
21-7/16"
25-1/2"
3. Remove top hinge (3 screws), reinstall hinge screw pin,
90°
Door Swing
90°
Door Swing
Black and White
Stainless Steel
Figure 3
02/2005
5
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
4. Remove the two door closer inserts from the existing
Other Site Requirements
bottom hinge and install as shown on the new bottom
Power Supply
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A circuit (normal household current). See
Hinge
Screw
Pin
Water Supply
Door
Closer
Inserts
The unit requires a 1/4-inch OD water supply line and a
Environmental Requirements
The surrounding air temperature must be at least 50°F
(10°C) but must not exceed 110°F (40°C). High ambient
temperature ranges and warmer water supply will cause
reduced ice production. Black and White units may be
installed outdoors in a covered area. Stainless Steel
CO2075FF units are deemed suitable for outdoor use by
UL. The unit must not be located near heat-generating
equipment or in direct sunlight.
Figure 7
Figure 8
5. Remove existing bottom hinge (3 screws) and remount
on opposite side TOP. Remove hinge screw pin.
6. Remove the plastic hole plug from the top of the door
to allow the pivot pin to be inserted in the new
location. Install the plug into the vacated hole on the
opposite side.
7. With bottom of door facing up, remove pivot plate
(2 screws), flip over, and remount on opposite side of
Figure 9
8. Holding door upright with top of door tilted forward,
place hole of door pivot plate on bottom hinge screw
9. Tilt top of door into
position in top hinge and
install top hinge screw pin.
10. Install plastic screw plugs
removed in Step 2 in old
hinge holes (3 each, top
and bottom).
Figure 10
6
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
Side-By-Side Installation
Instructions
4 Prepare and Install Door Panel
(Black and White Units Only)
For a complete refreshment center, install your CO2075FF
Ice Maker/Refrigerator beside a U-Line Drawer or Wine
that each Side-By-Side Installation will be different.
Two types of custom door panels can be installed on your
Black or White unit to harmonize with or accent the
surrounding décor: a Custom 1/4" Insert or a Full Overlay.
If no custom door panel is used, go on to 5 Adjust Door.
• Cut-out width for a side-by-side installation is the total
of the widths listed under Cut-Out Dimensions in each
unit’s Installation Guide.
Custom 1/4'' Door Panel Insert
For example:
Door Panel Preparation
Placing a CO2075FF Ice Maker/Refrigerator next to a
2015 series unit would require a cut-out width of:
24-3/16" + 15-3/16" = 39-3/8"
A custom door panel can be inserted into the doorframe.
Custom door panels can be flat or raised, as long as the
maximum panel thickness where inserted into the door
reveal (channel) is 1/4"-thick. For raised panels, the depth
of the reveal is 1/4" on all four sides.
Placing a CO2075FF Ice Maker/Refrigerator next to a
2075 series unit would require a cut-out width of:
24-3/16" + 24-3/16" = 48-3/8"
IMPORTANT
•
No trim kit is required. However, 1/4-inch space needs to
be maintained between the units to ensure
unobstructed door swing.
Raised panels will reduce the door’s 90° swing/zero
clearance if the unit is installed next to a wall or similar
• Units must operate from separate, properly grounded
electrical receptacles placed according to each unit’s
Electrical Specifications.
Cut the panel insert to the following dimensions.
Custom 1/4" Dimensions:
Width:
23-1/32"
Typical Side-By-Side Cut-Out
Height: 28-5/32"
The door panel must not weigh more than 20 lbs.
Door Panel Installation
Install the insert as follows:
1. Remove the door shelves by first pulling shelves
23-11/16"
34-1/4"
to
35-1/8"
7"
CAUTION
1/4" Space
Between
Appliances
1-1/2"
Use care when handling the insert. Insert edges may be
sharp.
Figure 11
2. Remove top hinge screw pin (7/64" Allen wrench or
Phillips screwdriver, depending on your unit’s
forward and lifting off bottom hinge pin.
02/2005
7
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
Full Overlay Door Panel
Door Panel Preparation
A full overlay door panel completely covers the
doorframe and handle to give a built-in appearance. See
your U-Line dealer for the optional Full Overlay Door
Panel Kit (P/N U-OL2075B — Black or P/N U-OL2075W —
White). Appropriate hardware, Modified Handle,
Replacement Hinges and a copy of these instructions will
be included in the kit.
1. Cut the overlay to the following dimensions (see
Figure 12
Figure 13
Full Overlay Dimensions:
Width:
23-3/4"
3. Pull door gasket out of groove (top edge of door only).
Start in the middle and pull outward, moving toward
not remove the three screws behind gasket.
Height: 29-7/8"
The door panel must not weigh more than 20 lbs.
4. Remove two outside screws holding door handle.
Slightly separate door handle from door (see
3/4"
13/16"
5. Pull handle up and off.
6. Remove and discard
existing panel and
cardboard spacer.
1/8"
1/8"
7. Slide custom door panel
insert into 1/4-inch
Relief Notch
for Pivot Plate
channel in door front.
8. Holding door gasket out
of the way, replace handle
Figure 14
on door, making sure it is
seated properly on insert
and that screw holes
line up.
Rear View
of
Wood Panel
29-7/8"
9. Install two small screws removed in Step 4.
10. Starting at the corners and working inward, push door
gasket into place on door.
11. Place door on bottom hinge pin and install upper hinge
screw.
23-3/4"
Figure 15
12. Reinstall the door shelves by lining up the bosses and
first pushing straight in, then down at a 45° angle (see
.
IMPORTANT
Rear View of wood panel for right-hand hinge shown. Use
mirror image for left-hand hinges.
notch in top corner and coinciding back corner of
specifications.
8
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
4. Drill hole for upper door hinge (top of panel) (see
13/32"
0.177" Dia. (#16 Drill)
Figure 16, Top View).
13/32"
x
11/16" Deep
0.177" diameter
3/8"
(#16 drill) x 11/16" deep
3/8"
Door Bottom:
13/16"
View).
x
5/16" Dia. 1/4" Deep
x
Chamfer 1/32" 45°
5/16" diameter x 1/4" deep
Top View
Bottom View
CAUTION
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood
when hardware is installed.
1/8"
1/8"
13/32"
1/8"
1/32" R
13/16"
Installation Instructions
1-17/32"
7/16"
Removing Existing Door
1. Remove the door shelves by first pulling shelves
up at a 45° angle then straight out (see Figure 37
1/8" R
13/16"
5/16" Dia.
2. Remove top hinge screw pin (7/64" hex key or Phillips
screwdriver, depending on your unit’s construction).
Remove the door by tilting forward and lifting off the
bottom hinge pin.
x
1/2" Deep
3/4"
Back View
Side View
Figure 16
3. Pull door gasket out of the groove (top edge of door
only). Start in the middle and pull outward, moving
force.
Route notch in top corner of overlay panel as shown
(see Top and Side Views). Top of notch is entire depth
of panel, front to back.
Width: 13/16"
Depth: 1/8"
Route notch in backside of top corner of overlay panel
(see Back and Side Views).
New Handle
Width: 13/16"
Depth: 1/8"
Old Handle
Height: 1-17/32" from top edge of panel (less 1/8" for
depth of notch on top of panel)
Radius of corner notch: 1/8" (see Back View)
View).
Figure 17
Figure 18
5/16" diameter x 1/2" deep, from the routed surface
4. Remove the three screws located on the back of the
CAUTION
Be careful not to drill too deep! Drilling holes too deep
may destroy your door panel.
02/2005
9
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
5. Remove the top handle and discard. (This handle will be
Tape
replaced with the Modified Handle included in the Full
Overlay Door Panel Kit.)
Back of
Wood
Panel
Removed
Door Panel
6. Remove the two screws located on both sides of the
lower handle. Remove the handle.
7. Attach the Modified Handle to the lower handle using
the three screws removed in Step 4. Set aside.
8. Slide the existing door panel out of the doorframe.
Side of
Attaching the Full Overlay Panel
Wood Panel
Bottom of
Wood Panel
1. Tap nylon inserts into the top holes drilled in the
overlay panel. Use two #6 screws to attach top pivot
5/16"
3/8"
Bottom
Both Sides
Figure 20
Typical Wood
Panel
x
Drill 5/32" 3/8" Deep
x
for usewith #10 5/8"
Wood Screw and Nylon
Spacer – 7 Places
#6 X 5/8"
Flat Head Screw
Two Required
Top Pivot
Plate
8 mm Plug Insert
Two Required
Rear View
Figure 19
of
Wood Panel
±
27" 1/4"
2. Place and tape the existing door panel on the back of
tape adjoining the panels and enlarge the seven holes
in the overlay panel using a 0.201" (#7) drill.
±
14-5/16" 1/4"
±
1" 1/8"
3. If a user-supplied cabinet handle will be used, attach its
hardware to the overlay panel at this time.
±
±
1" 1/32"
11-7/8"
1" 1/32"
Figure 21
4. Attach the door panel to the overlay panel using #10 x
5/8" wood screws and nylon spacers. The nylon spacers
fit between the overlay panel and the door panel as
door panel to slide back into the 1/4"-thick door
reveal (channel).
10
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
Typical
Door Panel
Pivot Post
Wood Panel
Wood Panel Top Hinge Plate
Top
(5/8" Longer than Existing Top Hinge Plate)
Pivot Plate
x
#10 5/8"
x
#8-32 1/2"
Round Head Screw
Seven Required
Flat Head Screw
Three Places
Plastic Spacer
Seven Required
Top Pivot Plate
Figure 22
Door Panel
5. Remove the existing bottom pivot plate and replace
Figure 24
3. Install the pivot post into the new Replacement Bottom
Hinge (using the 7/64" hex key or Phillips screwdriver)
and install the hinge onto the unit.
Existing
Door
Wood Panel Bottom Pivot Plate
(5/8" Longer Than
4. Replace the door closure assembly onto the bottom
closers align with holes in hinge and hinge plate.
Existing Bottom Pivot Plate,
Flush Side Facing Out)
Existing Bottom Pivot Plate
(Remove and Discard)
x
#8-32 3/8" SEMS Hex Screw
Two Places
Figure 23
Existing
Door
IMPORTANT
Door Closure Top
Boss
Door panel and overlay panel must be aligned properly or
the door will not operate correctly.
Door Closure Bottom
Assembling the Door
x
#8-32 1/2" Flat Head Screw
1. Install the assembled panel by sliding the original door
panel back into the doorframe.
Three Places
Boss
Pivot Post
Wood Panel Bottom Hinge Plate
2. Replace the two-piece Modified Handle assembly and
secure with the two screws removed in Step 6 under
Removing Existing Door.
(5/8" Longer than Existing Bottom Hinge Plate)
Figure 25
3. Starting at the corners and working toward the center,
push the door gasket back into place.
IMPORTANT
Installing the Door
Pivot posts must be cleaned. Closers must also be clean
and greased to ensure proper operation.
1. Remove the existing hinges from the unit, saving the
door closure assembly.
5. Place the modified door onto the pivot post.
2. Install the new Replacement Top Hinge onto the unit
6. Position door and install the pivot post into the top
hinge (using the 7/64" hex key or Phillips screwdriver).
7. Adjust door as needed for proper closure.
8. Check to see that light switch actuator bracket is
contacting the light switch properly.
9. Reinstall the door shelves by lining up the bosses and
first pushing straight in, then down at a 45° angle (see
.
02/2005
11
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
5 Adjust Door
Checking Door Alignment
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during door panel installation.
Slotted
Mounting
Holes
Notch
IMPORTANT
Properly aligned, the door should be 1/8" below the top of
Raise
Lower
Outside
Outside
Door Edge
Door Edge
Figure 28
1/8"
move UP, move the hinge plate toward the outside of
the door and retighten screws. If the top far edge of the
door needs to move DOWN, move the hinge plate
toward the inside of the door and retighten screws.
Figure 26
4. Mount the door to recheck alignment and repeat Steps
2 and 3 if further adjustment is necessary.
1. Compare the top edge of the door to the top edge of
the cabinet.
5. When top edge of door is parallel to top edge of
cabinet, remove the door and ensure the two screws
are secure.
2. If the door edge is 1/8" below and parallel to the top of
the cabinet, go on to 6 Prepare Plumbing. If it is not,
note whether the side opposite the hinge needs to be
moved UP or DOWN, and use the following procedure.
6. Remove the door closers from the bottom hinge, clean
thoroughly and lubricate the mating surfaces with
petroleum jelly.
Note: If door is adjusted correctly, but panel is not square
with the adjacent cabinets, slight adjustments can be
made by drilling the holes in the vinyl coated steel panel
7. Reinstall the closers, lining
up the bosses with holes in
hinge and hinge plate (see
Adjusting Door Alignment
8. Mount the door, install top
hinge pivot pin and go on
Door
Closer
Inserts
1. Remove top hinge screw
pin (7/64 Allen wrench or
"
to 6 Prepare Plumbing
.
Phillips screwdriver,
depending on your unit’s
construction, see Figure
27). Remove door by
tilting forward and lifting
off bottom hinge pin.
Boss
Figure 29
2. With door upside-down,
loosen but do not remove
the two screws on the
Figure 27
door’s bottom hinge plate.
12
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
2. Locate the compression fitting and ferrule packed with
6 Prepare Plumbing
the unit. Slide the compression fitting and ferrule over
the 1/4-inch OD water supply line. Do not use thread
sealing compound or tape. Using two wrenches,
tighten the compression fitting on the supply line (see
CAUTION
Plumbing installation must observe all state and local
codes. All water connections MUST BE made by a licensed/
qualified plumbing contractor. Failure to follow
recommendations and instructions may result in damage
and/or harm.
3. Carefully bend the water supply line into position and
Avoid kinking the water supply line.
WARNING
To prevent accidental electrocution, make certain
that the floor surfaces surrounding the unit are
dry whenever power is removed from, or applied
to, the unit.
Water Supply Connection
When connecting the water supply, follow these
guidelines:
• Review the local plumbing codes before you install the
unit.
• Connect to the cold water supply.
Figure 32
• The water pressure should be between 20 and 120 psi.
• Install a shut-off valve in the 1/4 inch OD water supply
line.
IMPORTANT
Normal operation creates some vibration. A water supply
line contacting cabinet wall may cause excessive noise
during operation or damage to the line.
• Connect sufficient tubing to the unit so that tubing
may be looped, allowing the unit to be removed for
certain that the tubing is not pinched or damaged
during installation.
4. For recessed installations, allow extra water supply line
length to provide slack for easy removal from the
against kinking the line.
• U-Line recommends the use of copper tubing for
installation.
To connect to water supply:
5. Go on to 7 Prepare Power Supply
.
1. Install the 1/4 inch OD copper water line from the
Water
Connection
Figure 30
Figure 31
02/2005
13
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
7 Prepare Power Supply
8 Level the Unit
Electrical Specifications
Leveling Information
CAUTION
IMPORTANT
It is extremely important that the unit is level. If it is not
level, the ice mold will not fill evenly.
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (three-
prong), polarized receptacle that has been placed by a
qualified electrician.
1. Use a level to check the
levelness of the ice maker
from front to back and
from side to side. Level
should be placed along
top edge and side edge
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current).
An individual, properly grounded branch circuit or circuit
breaker is recommended. GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be
sure to consult your local codes.
Check
Level
Figure 34
2. If the ice maker is not level, adjust the feet on the
23-11/16"
7"
Turn Foot to Adjust
1-1/2"
Figure 35
Figure 33
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level. Go on to
9 Install the Unit
.
WARNING
Installation Tip
SHOCK HAZARD — Electrical Grounding Required.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
If the room floor is higher than the floor in the cut-out
opening, adjust the rear feet to achieve a total unit rear
height of 1/8 less than the opening’s rear height. Shorten
"
the unit height in the front by adjusting the front feet.
This allows the unit to be gently tipped into the opening.
Readjust the front feet to level the unit after it is correctly
positioned in the opening.
• Never use an extension cord to connect power to
the unit.
Go on to 8 Level the Unit.
14
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
Door Shelves
9 Install the Unit
1. First pull shelf up at a 45°
angle, then straight out
Installation of the CO2075FF
Notch
1. Open the water supply valve in the main water source.
2. Choose new location and
line up on bosses. First
push straight in, then
down at a 45° angle.
2. Make sure the cycle selector switch is in the OFF
3. Plug in the power cord.
Boss
4. Gently push the unit into position. Be careful not to
kink the drain or water supply line or entangle the
electrical cord.
5. Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit’s top
surface should be approximately 1/8" below the
countertop.
Figure 37
Installation Troubleshooting
6. Remove the tape from the glass shelves and wipe out
the inside of the unit with a clean, water-dampened
cloth.
Problem
Q:
Water is leaking under the unit.
Relocating the Shelves
Solution
A:
Both the glass shelves in the refrigerator and the inner
door shelves can be moved to accommodate your bottles,
cans and containers.
A water leak under the unit is most likely caused by a bad
connection in the water supply line. Make sure the water
line’s brass fitting is screwed tight to its valve and
threaded correctly.
Glass Shelves on Right-Hand Hinge Units
1. Open door fully, grasp shelf firmly, lift front edge
slightly, and pull straight out.
Problem
Q:
The door remains open unless it is pushed closed.
2. Choose new location and slide shelf onto the
appropriate rib.
Solution
A:
Glass Shelves on Left-Hand Hinge Units
The hinges should be self-closing when the door is open
approximately 8". If this is not the case, make sure the
out about 6” to clear the
wall’s molded protrusion.
closers (at the bottom of the hinge pin) are clean, greased
and installed correctly. Also, re-check leveling from front
to back of the unit and readjust if necessary. Make sure
that pivot plate is installed correctly.
1. Pull Out 6"
2. Tilt right-hand edge of
3. Pull
2. Tilt
shelf up.
Problem
3. Keeping at this angle and
hugging the right wall,
pull the shelf out.
Q:
The custom overlay door was designed to align with the
rest of the cabinet doors, but the unit has crept forward.
4. Choose new location and
insert over ribs, tilting
right-hand edge up. Push
in, then lower shelf onto
ribs.
Solution
A:
Make sure that the electrical cord and water supply line
are not obstructing the installation.
Figure 36
02/2005
15
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CO2075FF — Ice Maker/Refrigerator
About Settings
10 Start-Up for the First Time
Initial Start-Up
No adjustments should be necessary at this time. For
information about Adjusting the Temperature Control
and Adjusting the Cube Size, see the User Manual.
Once installation and leveling is complete, the unit is
ready for initial start-up and operation. The ON/OFF
Start-Up Troubleshooting
Problem
Q:
Unit does not appear to turn on when switch is set to ON.
Temperature
Control Knob
OFF
Solution
A:
ON
Make sure unit is plugged in and outlet has power (circuit
breaker has not tripped). Check to see that light switch
actuator bracket is contacting the light switch properly.
Remember that the ice maker mechanism will not fill the
mold with water until the mold reaches the proper
temperature.
4
3
1
5
2
6
OFF
ON
7
WARMER
COLDER
ON/OFF
Switch
Figure 38
Problem
Q:
1. Put the ON/OFF switch in
the ON position and set
the Temperature Control
Knob at 4.
Water does not appear to be flowing into unit.
Solution
A:
2. As soon as the ice maker
mold reaches the proper
temperature, the ice
Check that the water is connected and turned on and the
line is not obstructed.
maker mechanism will fill
the mold with water.
Problem
Q:
The cubes produced during the first two to three hours of
operation have been discarded. New cubes still appear
cloudy.
Note: The first cubes may be
small because of air in the
water line. After two hours,
cubes will be standard size.
Figure 39
Solution
A:
3. The ice maker will continue to produce until the bin is
full. You may interrupt production by raising the bin
arm into an upright and locked position (see Figure
39). While the bin arm is locked, the unit will maintain
temperature for ice storage.
This is normal and is caused by air being trapped in the
cube during fast freezing.
IMPORTANT
See the User Manual’s Troubleshooting Guide for more
solutions.
IMPORTANT
It is possible that dirt or scale will dislodge in the water
line. Always throw away all ice cubes made during the
first twenty-four (24) hours of operation.
CAUTION
• The ice bucket MUST be fully inserted to avoid freezing
products in the refrigerator section. The ice bin door
must be fully closed with the door lip inside the ice
bucket.
• Do not place cans or bottles so they are touching the
back wall of the refrigerator section, as they may
freeze.
• Do not place any objects over air inlet or outlet in the
freezer section.
16
02/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
™
Who to Call
Service Information
If the need for service arises, contact the dealer from
whom the unit was purchased. State the Model Number
and Serial Number and explain the problem. The Model
and Serial Number plate is located inside unit at upper
right hand corner.
If you need to locate a service company, you can go online
company by zip code.
For more than four decades, U-Line has distinguished itself as the leader in built-in
undercounter ice making, refrigeration and wine storage appliances.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
undercounter icemakers, Combo® icemaker/refrigerators, Wine Captain® wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2005 U-Line Corporation
Publication No. 30061E
02/2005 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|