TABLE OF CONTENTS
Welcome....................................................................................3
Features .................................................................................3
Installation ................................................................................4
Package Contents ..................................................................4
Installing the Hardware...........................................................5
Physical Installation ............................................................5
Powering the AP .................................................................5
Connecting the Device to Computers and Network............6
LED Display ........................................................................7
Setting up the Wireless AP.....................................................8
The Configuration Interface ....................................................9
Logging In...............................................................................9
General Information.............................................................. 11
Wireless Statistics.................................................................13
Password Setup ...................................................................14
Saving the Configuration......................................................15
Access Point Configuration..................................................16
LAN Setup ............................................................................16
Reset Button.........................................................................18
WLAN Setup.........................................................................19
WEP Encryption................................................................21
WEP Key Configuration ....................................................22
WLAN Access Control ..........................................................26
Firmware Upgrade................................................................29
Troubleshooting.....................................................................35
Changing The IP Address......................................................36
Specifications.........................................................................40
Legal Notice............................................................................41
IC Notice:.................................................................................41
FCC Information.....................................................................41
Precautions! ...........................................................................43
One Year Limited Warranty ...................................................46
Glossary..................................................................................48
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Hardware
Connecting the Device to Computers and Network
When you connect the WNP1000 Wireless AP to a switch or
router, check the WNP1000 Wireless AP LAN LED.
Solid green indicates a link to a fast Ethernet Switch
(100Mbps). Solid amber indicates a link to a 10Base-T Switch.
Flashing indicates activity. A typical configuration is shown in
the figure below.
Physical Installation
Select a safe location for the WNP1000 Wireless AP. You may
install the WNP1000 Wireless AP either upright on a desk or
bookcase using the included stand, or mount the WNP1000
Wireless AP on a wall using the two screws as shown in the
figure below. Leave adequate room for the antennas to unfold
and allow adequate cable length for both the power and
Ethernet cables.
Powering the AP
Plug the power adapter into an AC power outlet and connect
the output of the power supply to the power jack on the rear of
the WNP1000 Wireless AP. The power LED should turn On
(Blue) immediately.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Display
Setting up the Wireless AP
The following table summarizes the operation of the LEDs on
the WNP1000 Wireless AP.
The WNP1000 802.11b Access Point is configured to work with
your cable/dsl router, switch or hub and other 802.11b wireless
products directly out of the box. There is no need for you to
configure your Access Point, unless you want to enable
increased security (WEP), change the IP Address, or other
configuration options.
LED
State
Description
Power On
When the device is powered, this LED is
on.
Wireless On
Indicates one or more wireless clients are
connected
If you want to change the default configurations, you will need
to access the browser-based utility of the WNP1000 Wireless
AP, you need a computer with the TCP/IP protocol enabled and
web browser software (Microsoft’s Internet Explorer, Netscape,
etc.).
Blink
Indicates that wireless data is being
transmitted and/or received
OFF
Ethernet On
No wireless transmission occurring.
The LED will light up if the WNP1000
Wireless AP is connected to a hub or
computer (speed indicated by color).
In order for your computer to communicate with the WNP1000,
both (your computer and the AP) will need to be on the same
Local Area Network, i.e. they must have similar IP Addresses.
The default IP address of the WNP1000 Wireless AP is
be on the same network (i.e., at a LAN IP Address such as
192.168.1.2, 192.168.1.3, etc.)
Blink
Indicates that data is being
transmitted/received
Green Indicates the LAN port is operating at
100Mbps
Note: If you are having trouble communicating with your
Access Point, please see “Troubleshooting” on page
37.
Amber Indicates the LAN port is operating at
10Mbps
You can connect to the browser based configuration screens
from any of the following three options:
a) Wirelessly connect through a wireless 802.11b client in
your PC or Laptop. (Uniden’s PCW300, PCW200 or
PCW100 802.11b clients.)
b) Connect both the WNP1000 Wireless AP and the
computer to a hub using “straight-through” Ethernet
cables.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
c) Connect the computer directly to the WNP1000
1. Type “http://192.168.1.10/” into the Location field
(or the URL field) at the top of the browser window
and hit the Enter key. This is the same location were
you type in the web address such as
IP address of the WNP1000 Wireless AP.)
Once you hit the Enter key, the “Enter Network
Password” window will appear.
Wireless AP using a “crossover” Ethernet cable.
If you wish to setup the WNP1000 Wireless AP by using an
802.11b enabled PC, make sure the 802.11b client is in
“Infrastructure” mode, and has an SSID of “UNIDEN” or blank.
The default IP address of the WNP1000 Wireless AP LAN
interface is 192.168.1.10 and the default network mask
255.255.255.0.
The Configuration Interface
The WNP1000 Wireless AP incorporates a browser-based
management/configuration interface. The following sections
guide you through configuring your WNP1000 Wireless AP and
detailing the information found within each section.
Logging In
2. Type “admin” (lower case) in the User Name field,
leave the Password field blank, and click OK.
The General Information web page will appear next.
Open a web browser on your computer configured for TCP/IP
networking. Make sure that the computer and the
WNP1000 Wireless AP are on the same local area
network, with similar IP addresses. (If you are having
trouble communicating with your Access Point, please
see “Troubleshooting” on page 37.)
3. After you are logged into the Access Point you can
change the User Name and Password.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
·
LAN MAC Address: Displays the Ethernet MAC address of
the LAN (Ethernet) interface of the WNP1000 Wireless AP.
A MAC address consists of six 2-digit number pairs that
uniquely identify an Ethernet device.
You are now logged into the Configuration tool for the
WNP1000 Wireless AP. To navigate the tool, click on any
items located on the left side of the page.
·
·
Wireless MAC Address: Displays the MAC address of the
wireless interface of the WNP1000 Wireless AP.
IP Address: Displays the IP address of the local LAN
interface of the WNP1000 Wireless AP. The default IP
address is 192.168.1.10.
·
Subnet Mask: Displays the local subnet mask of the LAN
interface of the WNP1000 Wireless AP. The default subnet
mask is 255.255.255.0.
The fields on the “General Information” page are described
below. To see the current status, click the Refresh button.
·
·
Hardware Version: Displays the hardware version of your
WNP1000 Wireless AP.
Software Version: Displays the version of the software
installed on the WNP1000 Wireless AP. This changes
whenever you install a software upgrade.
·
Time since last boot: Displays the time that has elapsed
since the WNP1000 Wireless AP was last started.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Statistics
Password Setup
This page shows the Wireless LAN MAC Address of the
WNP1000 Wireless AP, as illustrated in the figure below.
The “Password Setup” page is for changing the security
settings of the WNP1000 Wireless AP. If you wish to change
the User Name or Password, fill in the appropriate fields and
click the Apply button. Please note that the Password and
Confirm Password fields must contain the same value.
Also on this page, you can reset the unit to factory defaults.
Please be aware that the default LAN IP Address is
192.168.1.10, and the default User Name is “admin” (with a
blank password).
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving the Configuration
Access Point Configuration
The configuration changes that you make are automatically
saved into the flash memory of the WNP1000 Wireless AP
within a few seconds after you click the Apply button.
However, the WNP1000 Wireless AP will continue to use the
previous configuration values until you restart the WNP1000
Wireless AP by clicking the Reboot button on the left manual
page.
Through the following procedure, you can enable the wireless
operation of the WNP1000 Wireless AP to allow
communication between wireless clients and devices on your
wired network such as a DSL/Cable modem, printers, file
servers, and e-mail servers.
LAN Setup
Each time you make a change, the WNP100 Wireless AP will
remind you by displaying a page such as the one shown below:
Click LAN Setup on the left menu. The following page will
appear.
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MAC Address:
Reset Button
Displays the Ethernet MAC address of the LAN (Ethernet)
interface of the WNP1000 Wireless AP. You may not change
the MAC address of your WNP1000 Wireless AP.
If you change the IP address of the WNP1000 Wireless AP
and forget the IP address, you can reset the access point back
to the factory default settings, 192.168.1.10.
Change the following fields as desired, and then click Apply.
Please remember that changes will not take effect until after the
WNP1000 Wireless AP is restarted.
Press and hold the Reset Button for three seconds with the end
of a paper clip, while the access point is ON. The access point
will then restore the unit to the original factory settings. The
Reset Button is located on the bottom of the WNP1000
Wireless AP.
LAN IP Address:
In this field, you enter the IP Address of the WNP1000
Wireless AP’s LAN port. If you change this address from the
factory default of 192.168.1.10, please remember the new
address, as you will need to use it to access the WNP1000
Wireless AP for configuration in the future. However, if you
forget the IP Address you can press the Reset button located
on the bottom of the WNP1000 Wireless AP. Push and
holding the Reset Button for three seconds restores all
settings to the factory default settings.
Note: All settings you entered for the SSID, WEP, User Name
and Password will be erased and you will need to re-
configure the unit to your settings.
Pressing the Reset Button once will is a soft boot and
will refresh the Access Points connections.
Subnet Mask:
In this field, you enter the Subnet Mask of the local network to
which the WNP1000 Wireless AP is attached. The default
Subnet Mask is 255.255.255.0.
Reset Button
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Set each of the parameters on this page as desired, and click
Apply. The parameters are described in more detail below
WLAN Setup
You are now ready to begin setting up the wireless portion of
your network. Click WLAN Setup on the menu, and the
following page will appear.
SSID:
The Service Set Identifier (SSID) is a 32-character, case-
sensitive field that identifies your WNP1000 Wireless AP and
wireless network to wireless clients that support the
IEEE802.11b wireless standard. You should use a unique SSID
to control access to your private network, and to prevent
conflicts with other wireless networks that may be nearby. The
WNP1000 Wireless AP is configured with a default SSID of
UNIDEN.
Note: All clients on the same wireless LAN must have the
same SSID. If you change the SSID on the WNP1000
Wireless AP, you must change the SSID for each
computer and/or device you are wanting to connect
using the 802.11b wireless network.
Channel:
Channels are the spectrum range where your wireless signals
are transmitted. The default is channel 1. However, to
maximize performance for your wireless network, another
channel may give you better performance. Select the channel
you wish to use from the pull-down menu.
Note: For better performance, avoid using channels occupied
by other AP’s in the area.
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
WEP Encryption
WEP Key Configuration
To make your network more secure, you may choose to use
Wired Equivalent Privacy (WEP). WEP is an encryption
scheme used to protect your wireless data communications.
WEP uses a combination of 64-bit or 128-bit keys to provide
access control to your network and encryption security for
every data transmission. The WNP1000 Wireless AP supports
WEP keys either can be entered manually, or can be generated
by using a simple-to-type passphrase.
Passphrase Method
When you enter a passphrase, the WNP1000 Wireless AP
generates four WEP keys for you. You can generate those
same WEP keys on any wireless client whose configuration
both 64-bit WEP and 128-bit WEP.
To decode a data
transmission, each point in a network must use an identical 64-
bit or 128-bit key. In simple terms, a 128-bit key will give you a
more secure network than a 64-bit key.
utility supports passphrases.
passphrase, perform the following steps.
To setup WEP using a
1. Select either 64-bit or 128-bit WEP encryption from the
pull-down menu.
2. Click on Auto (Generated from passphrase).
Note: Some products refer to 64-bit encryption as 40-bit
encryption. Both are names for the same encryption
technology.
3. Type
a
passphrase of up to 31 alphanumeric
characters into the Passphrase field and click
802.11b clients inserted into your laptop or desktop
computer must have the same WEP settings as the AP
in order for them to communicate with each other.
Generate to create the hex key(s).
4. Select the active WEP key set (1, 2, 3, or 4) for 64-bit
encryption. WEP 128-bit encryption creates only one
key. Verify that you are using the same active key for
all clients on your wireless network. (If a client does
not support passphrases, you may manually enter the
desired key on that client.)
5. Click Apply. Remember that changes do not take
effect until after you restart your WNP1000 Wireless
AP by clicking the Reboot button.
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
A sample WEP configuration using a passphrase is shown in
the following figure.
Manual Key Entry
To manually enter the WEP keys, perform the following steps:
1. Select either 64-bit or 128-bit WEP encryption from the
pull-down menu.
2. Click on Manual (Enter in the table below).
3. When WEP 64-bit is selected, type five alphanumeric
characters in the range of “a-z”, “A-Z” and “0-9” (e.g.
MyKey) in the WEP Key 1 entry field. Alternatively, you
may enter 10 digit hexadecimal values in the range of
“A-F” and “0-9” (as shown in the example below).
You can also enter WEP keys in the Key 2, Key 3 and
Key 4 if you wish. Select the active WEP key set (1, 2,
3, or 4) for 64-bit encryption. WEP 128-bit encryption
uses only one key. Verify that you are using the same
active key for all clients on your wireless network.
4. Click Apply. Remember that changes do not take
effect until after you restart your WNP1000 Wireless
AP by clicking the Reboot button.
23
24
Download from Www.Somanuals.com. All Manuals Search And Download.
A sample WEP configuration using manual key entry is shown
in the following figure.
WLAN Access Control
When you click WLAN Access Control the following page will
appear.
25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MAC Address Access Control
Uniden’s client MAC Address can be found listed on the
product label. For 802.11b clients, you can find the MAC
Address listed on the package of the client network interface
In 802.11b, the MAC Address may be used as a means to
control network access. If you choose Disable MAC Address
Access Control, all clients within range of your Access Point
can access your WNP1000 Wireless AP and its associated
network if you don’t use other means of protection
(such as WEP).
card.
It consists of 6 pairs of
characters, such as
00:30:AB:00:00:01.
After you have finished entering all MAC addresses, click
Apply to save your settings.
To enable MAC Address Access Control, click on Enable and
then click Apply. Click on Allow (beside Access Control
Mode). Next, enter a list of MAC addresses of clients that you
wish to allow on your network. To do so, click Add and type in
the MAC Address of each client in the pop-up page as shown
in the following figure.
You may also delete or modify MAC addresses in the list by
clicking on the button by the address, and then clicking Delete
or Modify on the WLAN Access Control page
You may also choose to reverse the meaning of the MAC
Address list by clicking Block next to Access Control Mode.
Doing so will cause the WNP1000 Wireless AP to permit all
clients EXCEPT those whose MAC addresses are on the list to
have access to your network.
27
28
Download from Www.Somanuals.com. All Manuals Search And Download.
When you receive the warning shown below, click OK to
dismiss the warning.
Firmware Upgrade
The Firmware Upgrade capability is used to update the
software in your WNP1000 Wireless AP. To upgrade the
Firmware, first download the new Firmware from the support
on Firmware Update. The following page will be displayed.
Once the warning is dismissed and you have entered the file
name (or selected it via the Browse button), click the Update
button on the “Firmware Update” page to start the upgrade
process.
The dialog box shown below will appear to confirm that you
want to perform the upgrade. Click OK to continue the upgrade
process.
Once the “Firmware Update” page is displayed, you may
enter the file location directory path or click Browse to browse
the file system to the location of the firmware file to be
uploaded into WNP1000 Wireless AP.
DO NOT click any other buttons on your browser until the
upgrade process is complete.
The access point will
automatically display the web pages shown below. The
process will take several minutes to complete.
29
30
Download from Www.Somanuals.com. All Manuals Search And Download.
31
32
Download from Www.Somanuals.com. All Manuals Search And Download.
The “General Information” page will then be displayed.
Click OK and wait for the WNP1000 Wireless AP to reboot and
display the “General Information” page again. The upgrade
process is complete.
Please remember that configuration changes that you make
through the user interface (including firmware upgrades) are
automatically saved into the flash memory of the WNP1000
Wireless AP. However, changes will not take effect until after
you restart the WNP1000 Wireless AP by clicking the Reboot
button.
Once this page is displayed, click the Reboot button.
The following pop-up will appear.
33
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing The IP Address
Troubleshooting
For Windows 95, 98, and ME:
If you experience difficulty in transferring data between
computers, you may try the following steps:
1.
2.
Click on Start, Settings, Control Panel. Double click
on Network.
§
§
§
§
§
Ensure that the access point and all client computers
are using the same wireless channel.
In “The following network components are
installed” box, select the TCP/IP associated with your
network adapter. If you only have one network adapter
installed, you will only see one TCP/IP mentioned with
no association to a network adapter. Highlight it and
click the Properties button.
Ensure that the encryption settings are the same for all
computers.
Re-position the WNP1000 Wireless AP and/or the
computer.
3.
In the “TCP/IP Properties” window, select the “IP
Address” tab.
Adjust the orientation of the antennas on the access
point.
Note: PLEASE WRITE DOWN THE IP ADDRESS or THE BOX
FOR “OBTAIN AN IP ADDRESS AUTOMATICALLY” WAS
CHECKED ON THE “MEMO” PAGE OF THIS MANUAL,
PAGE 57. After you’ve configured the Access Point, you
will need to re-enter either the IP Address or check the
box for “Obtain an IP Address Automatically” into your
computer. Follow these same steps, but enter the
information YOU wrote down on the “Memo” page of
this manual, page 57.
Keep in mind that closer is not necessarily better for
devices of this type. If the devices are very close
together, move them apart
§
§
If you have a consistent problem with many or all
wireless devices on your network, you should consider
using a different wireless channel for your network
operations.
If you are not able to communicate with your Access
Point, the computer and the Access Point are not on
the same local area network,
4.
Select “Specify an IP address”. Enter a unique IP
address that is not used by any other computer
connected to the network. You can only use an IP
address in the range of 192.168.1.1 to 192.168.1.254.
Make sure that each IP address is unique for each PC
or network device.
The following provides you with instructions on how to
change the IP Address for your computer, so you can
access your 802.11b Access Point Configuration Utility.
5.
6.
Enter the Subnet Mask, 255.255.255.0.
Click the OK button in the “TCP/IP Properties”
window, and click OK in the “Network” window.
7.
Restart the computer if asked.
35
36
Download from Www.Somanuals.com. All Manuals Search And Download.
For Windows 2000:
For Windows NT 4.0:
1.
Click on Start, Settings, Control Panel. Double click
on Network and Dial-up Connections.
1.
2.
3.
Click on Start, Settings, Control Panel. Double click
on Network.
2.
Right click on the Local Area Connection that is
associated with the network adapter you are using,
and select the Properties option.
Select the Protocol tab, and double click on TCP/IP
Protocol.
When the window appears, make sure you have
3.
In the “Components checked are used by this
connection” box, highlight Internet Protocol
(TCP/IP), and click the Properties button.
selected the correct Adapter for your network adapter.
Note: PLEASE WRITE DOWN THE IP ADDRESS or THE BOX
FOR “OBTAIN AN IP ADDRESS AUTOMATICALLY” WAS
CHECKED ON THE “MEMO” PAGE OF THIS MANUAL,
PAGE 57. After you’ve configured the Access Point, you
will need to re-enter either the IP Address or check the
box for “Obtain an IP Address Automatically” into your
computer. Follow these same steps, but enter the
information YOU wrote down on the “Memo” page of
this manual, page 57.
Note: PLEASE WRITE DOWN THE IP ADDRESS or THE BOX
FOR “OBTAIN AN IP ADDRESS AUTOMATICALLY” WAS
CHECKED ON THE “MEMO” PAGE OF THIS MANUAL,
PAGE 57. After you’ve configured the Access Point, you
will need to re-enter either the IP Address or check the
box for “Obtain an IP Address Automatically” into your
computer. Follow these same steps, but enter the
information YOU wrote down on the “Memo” page of
this manual, page 57.
4.
Select “Specify an IP address”, and enter a unique IP
address that is not used by any other computer
connected to the network. You can only use an IP
address in the range of 192.168.1.1 to 192.168.1.254.
Make sure that each IP address is unique for each PC
or network device.
4.
Select Use the following IP address option. Enter a
unique IP address that is not used by any other
computer connected to the network. You can only use
an IP address in the range of 192.168.1.1 to
192.168.1.254. Make sure that each IP address is
unique for each PC or network device.
5.
6.
Enter the Subnet Mask, 255.255.255.0.
Click the OK button in the “TCP/IP Properties”
window, and click OK in the “Network” window.
5.
6.
Enter the Subnet Mask, 255.255.255.0.
Click the OK button in the “Internet Protocol (TCP/IP)
Properties” window, and click the OK button in the
“Local Area Connection Properties” window.
7.
Restart the computer if asked.
7.
Restart the computer if asked.
37
38
Download from Www.Somanuals.com. All Manuals Search And Download.
For Windows XP:
Specifications
1.
Click on Start, Control Panel. If your view is already
Model Number
WNP1000
Classic View, proceed to step 2. Otherwise, switch
your view to Classic View, located at the top left of the
window.
Wireless Network IEEE 802.11b
Standard
2.
3.
Double click on Network Connections.
LAN Network
Standard
IEEE 802.3 IEEE 802.3u
Right click on the Local Area Connection that is
associated with the network adapter you are using, and
select the Properties option.
RJ-45 connector
LAN Port
LED Indicators
Power, LAN Link/Activity, Wireless
Status
4.
In the “This connection uses the following items”
box, highlight Internet Protocol (TCP/IP). Click the
Properties button.
Power
External, 7.5V DC, 1A
Operating
Environment
Operating Temperature: 0°C ~ 55°C
Storage Temperature: -20°C ~ 70°C
Humidity (non-condensing): 10% ~ 90%
RH
Note: PLEASE WRITE DOWN THE IP ADDRESS or THE BOX
FOR “OBTAIN AN IP ADDRESS AUTOMATICALLY” WAS
CHECKED ON THE “MEMO” PAGE OF THIS MANUAL,
PAGE 57. After you’ve configured the Access Point, you
will need to re-enter either the IP Address or check the
box for “Obtain an IP Address Automatically” into your
computer. Follow these same steps, but enter the
information YOU wrote down on the “Memo” page of
this manual, page 57.
Frequency Band
2.412GHz ~ 2.462GHz (North America)
11 channels for US and Canada
Operating
Channels
Radio Data Rates 11/5.5/2/1 Mbps
Wireless Medium Direct Sequence Spread Sequence
(DSSS)
5.
Enter a unique IP address that is not used by any other
computer connected to the network. You can only use
an IP address in the range of 192.168.1.2 to
192.168.1.254. Make sure that each IP address is
unique for each PC or network device.
Modulation
Techniques
DBPSK @ 1 Mbps
DQPSK @ 2 Mbps
CCK @ 5.5 and 11 Mbps
Encryption
40/64-bit and 128-bit Wired Equivalent
Privacy (WEP)
6.
7.
Enter the Subnet Mask, 255.255.255.0.
Click the OK button in the “Internet Protocol (TCP/IP)
Properties” window. Click the OK button in the
“Local Area Connection Properties” window.
Certification
FCC Part 15
8.
Restart your computer if asked.
39
40
Download from Www.Somanuals.com. All Manuals Search And Download.
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures: (1) Reorient or relocate the
receiving antenna, (2) Increase the separation between the
equipment and receiver, (3) Connect the equipment into an
outlet on a circuit different from that to which the receiver is
connected, (4) Consult the dealer or an experienced radio/TV
technician for help.
Legal Notice
Statement of Conditions
Uniden reserves the right to make changes to the products
described in this document without notice.
Uniden does not assume any liability due to the user or
application of the product(s) or circuit layout(s) described
herein.
IC Notice:
Federal Communications Commission (FCC) Radiation
Exposure Statement
This Class B digital apparatus complies with Canadian ICES-
003.
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. In order to avoid the
possibility of exceeding the FCC radio frequency exposure
limits, human proximity to the antenna shall not be less than
20 cm (8 inches) during normal operation.
FCC Information
Federal Communications Commission (FCC) Compliance
Notice: Radio Frequency Notice
The FCC Wants You To Know
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
Changes or modifications to this product not expressly
approved by Uniden, or operation of this product in any way
other than as detailed by the owner’s manual, could void your
authority to operate this product and will void any warranty.
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
41
42
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Do not overload wall outlets and extension cords, as
this can result in the risk of fire or electrical shock.
Precautions!
Before you read anything else, please observe the following:
8. Never push objects of any kind into this product
through cabinet slots, as they may touch dangerous
voltage points or short out parts that could result in a
risk of fire or electric shock. Never spill liquid of any
kind on the product.
Warning!
Uniden America Corporation DOES NOT represent this unit
to be waterproof. To reduce the risk of fire, electrical shock,
or damage to the unit, DO NOT expose this unit to rain or
moisture.
9. To reduce the risk of electric shock, do not disassemble
this product. Take it to qualified service personnel
when service or repair work is required. Opening or
removing covers may expose you to dangerous
voltages or other risks. Incorrect reassembly can
cause electric shock when the appliance is
subsequently used.
Important Safety Instruction
When using your product, these basic safety precautions
should always be followed to reduce the risk of fire, electrical
shock, and injury to persons:
1. Read and understand all instructions.
10. Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
2. Follow all warnings and instructions marked on the
product.
3. Do not use this product near water; for example, near a
bathtub, washbowl, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool.
A. If liquid has been spilled into the product.
B. If the product has been exposed to rain or water.
C. If the product does not operate normally when following
the operating instructions. (Adjust only those controls
that are covered by the operating instructions. Improper
adjustment of other controls may result in damage and
will often require extensive repair work by a qualified
technician.)
4. Do not place this product on an unstable cart, stand, or
table. The product may fall, causing serious damage to
the unit.
5. Slots and openings in the cabinet and the back or
bottom are provided for ventilation. To protect the
product from overheating, these openings must not
be blocked or covered. This product should never
be placed near or over a radiator or heat register.
This product should not be placed in a built-in
installation unless proper ventilation is provided.
D. If the product has been dropped or the cabinet has
been damaged.
E. If the product exhibits a distinct change in performance.
6. If this product includes a cable, do not allow anything
to rest on it and do not locate this product where the
cable will be damaged by persons walking on it.
43
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Electrical Considerations
One Year Limited Warranty
Unplug all electrical appliances when you know an electrical
storm is approaching. Lightning can pass through your
household wiring and damage any device connected to it.
This product is no exception.
Important: Evidence of original purchase is required for
warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
Warning!
ELEMENTS OF WARRANTY: Uniden warrants, for one year,
to the original retail owner, this Uniden Product to be free from
defects in materials and craftsmanship with only the limitations
or exclusions set out below.
Please do not attempt to unplug any appliance during an
electrical storm.
WARRANTY DURATION: This warranty to the original user
shall terminate and be of no further effect twelve (12) months
after the date of original retail sale. The warranty is invalid if
the Product is (A) damaged or not maintained as reasonable
or necessary, (B) modified, altered, or used as part of any
conversion kits, subassemblies, or any configurations not sold
by Uniden, (C) improperly installed, (D) serviced or repaired by
someone other than an authorized Uniden service center for a
defect or malfunction covered by this warranty, (E) used in any
conjunction with equipment or parts or as part of any system
not manufactured by Uniden, or (F) installed or programmed
by anyone other than as detailed by the owner’s manual for
this product.
STATEMENT OF REMEDY: In the event that the product does
not conform to this warranty at any time while this warranty
is in effect, warrantor will either, at its option, repair or replace
the defective unit and return it to you without charge for parts,
service, or any other cost (except shipping and handling)
incurred by warrantor or its representatives in connection with
the performance of this warranty. Warrantor, at its option, may
replace the unit with a new or refurbished unit. THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN
45
46
Download from Www.Somanuals.com. All Manuals Search And Download.
LIEU OF AND EXCLUDES ALL OTHER WARRANTIES
OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow this exclusion or limitation of
incidental or consequential damages so the above limitation
or exclusion may not apply to you.
Glossary
Ad.Hoc - Ad.Hoc mode allows computers equipped with wireless transmitters
and receivers to communicate directly with each other, eliminating the need for
an access point.
Adapter - A printed circuit board that plugs into a PC to add to capabilities or
connectivity to a PC. In a networked environment, a network interface card
(NIC) is the typical adapter that allows the PC or server to connect to the
intranet and/or Internet.
Backbone - The part of a network that connects most of the systems and
networks together and handles the most data.
LEGAL REMEDIES: This warranty gives you specific legal
rights, and you may also have other rights which vary from
state to state. This warranty is void outside the United States
of America.
Bandwidth - The transmission capacity of a given facility, in terms of how much
data the facility can transmit in a fixed amount of time; expressed in bits per
second (bps).
Bit - A binary digit. The value 0 or 1 used in the binary numbering system.
Also, the smallest form of data.
PROCEDURE FOR OBTAINING PERFORMANCE OF
WARRANTY: If, after following the instructions in the owner’s
manual you are certain that the Product is defective, pack the
Product carefully (preferably in its original packaging).
The Product should include all parts and accessories originally
packaged with the Product. Include evidence of original
purchase and a note describing the defect that has caused you
to return it. The Product should be shipped freight prepaid, by
traceable means, to warrantor at:
Boot
-
To cause the computer to start executing instructions.
Personal computers contain built-in instructions in ROM chip that are
automatically executed on startup. These instructions search for the operating
system, load it, and pass control to it.
Bridge - A device that interconnects different networks together.
Broadband - A data-transmission scheme in which multiple signals share the
bandwidth of a single medium. This allows the transmission of voice, data, and
video signals over that medium. Cable television uses broadband techniques to
deliver dozens of channels over one cable.
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Blvd
Fort Worth, TX 76155
(800) 775-9060
Browser - An application program that provides a way to look at and interact
with all the information on the World Wide Web or PC. The word “browser”
seems to have originated prior to the Web as a generic term for user interfaces
that let you browse text files online.
47
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Download - To receive a file transmitted over a network. In a communications
session, download means receive, and upload means transmit.
Cable Modem – A device that connects a computer to the cable television
network, which in turn connects to the Internet. Once connected, cable modem
users have a continuous connection to the Internet. Cable modems feature
asymmetric transfer rates: around 36 Mbps downstream (from the Internet to
the computer), and from 200 Kbps to 2 Mbps upstream (from the computer to
the Internet).
Driver - A software module that provides an interface between a network
interface card and the upper-layer protocol software running in the computer; it
is designed for a specific adapter, and is installed during the setup of the
adapter.
Data Packet - One frame in a packet-switched message. Most data
communication is based on dividing the transmitted message into packets.
For example, an Ethernet packet can be from 64 to 1518 bytes in length.
DSSS (Direct-Sequence Spread-Spectrum) - DSSS generates a redundant bit
pattern for each bit transmitted. This bit pattern is called a chip (or chipping
code). The longer the chip, the greater the probability that the original data can
be recovered. Even if one or more bits in the chip are damaged during
transmission, statistical techniques embedded in the radio can recover the
original data without the need for retransmission. To an unintended receiver,
DSSS appears as low power wideband noise and is rejected (ignored) by most
narrowband receivers.
Default Gateway - The routing device used to forward all traffic that is not
addressed to a station within the local subnet.
DHCP (Dynamic Host Configuration Protocol) - A protocol that lets network
administrators centrally manage and automate the assignment of Internet
Protocol (IP) addresses in an organization’s network. Using the Internet’s set of
protocol (TCP/IP), each machine that can connect to the Internet needs a
unique IP address. When an organization sets up its computer users with a
connection to the Internet, an IP address must be assigned to each machine.
Without DHCP, the IP address must be entered manually at each computer
and, if computers move to another location in another part of the network, a
new IP address must be entered. DHCP lets a network administrator supervise
and distribute IP addresses from a central point and automatically sends a new
IP address when a computer is plugged into a different place in the network.
DHCP uses the concept of a “lease” or amount of time that a given IP address
will be valid for a computer. The lease time can vary depending on how long a
user is likely to require the Internet connection at a particular location.
It’s especially useful in education and other environments where users change
frequently. Using very short leases, DHCP can dynamically reconfigure
networks in which there are more computers than there are available
IP addresses.
Dynamic IP Address - An IP address that is automatically assigned to a client
station in a TCP/IP network, typically by a DHCP server. Network devices that
serve multiple users, such as servers and printers, are usually assigned static
IP addresses.
Dynamic Routing - The ability for a router to forward data via a different route
based on the current conditions of the communications circuits. For example, it
can adjust for overloaded traffic or failing lines and is much more flexible than
static routing, which uses a fixed forwarding path.
Ethernet - IEEE standard network protocol that specifies how data is placed on
and retrieved from a common transmission medium. Has a transfer rate of 10
Mbps. Forms the underlying transport vehicle used by several upper-level
protocols, including TCP/IP and XNS.
Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet
CSMA/CD network access method.
DHCP supports static addresses for computers containing Web servers that
need a permanent IP address.
Firewall – A firewall is a set of related programs, located at a network gateway
server, which protects the resources of a network from users from other
networks. (The term also implies the security policy that is used with the
programs.) An enterprise with an intranet that allows its workers access to the
wider Internet installs a firewall to prevent outsiders from accessing its own
private data resources and for controlling what outside resources to which its
own users have access. A firewall, working closely with a router, examines
DNS - The Domain Name System (DNS) is the way that Internet domain names
are located and translated into an Internet Protocol (IP) address. A domain
name is a meaningful and easy-to-remember “handle” for an Internet address.
Domain - A sub network comprised of a group of clients and servers under the
control of one security database. Dividing LANs into domains improves
performance and security.
49
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Firmware - Programming that is inserted into programmable read-only memory,
thus becoming a permanent part of a computing device.
IPCONFIG – A utility that provides for querying, defining and managing IP
addresses within a network. This utility is commonly used under Windows NT
and 2000, for configuring networks with a static IP address.
Flash Memory - Flash memory is an electronic storage device capable of
recording several megabytes of data files.
IPSec (Internet Protocol Security) - A developing standard for security at the
network or packet-processing layer of network communication.
A
big
Fragmentation - Breaking a packet into smaller units when transmitting over a
network medium that cannot support the original size of the packet.
advantage of IPSec is that security arrangements can be handled without
requiring changes to individual user computers.
Hardware
-
Hardware is the physical aspect of computers,
IRQ (Interrupt Request) – A hardware interrupt on a PC. There are 16 IRQ
lines used to signal the CPU that a peripheral event has started or terminated.
Except for PCI devices, two devices cannot use the same line.
telecommunications, and other information technology devices. The term arose
as a way to distinguish the “box” and the electronic circuitry and components of
a computer from the program you put in it to make it do things. The program
came to be known as the software.
ISP (Internet Service Provider) - A company that provides individuals and
companies access to the Internet and other related services such as website
building and virtual hosting.
Hub - The device that serves as the central location for attaching wires from
workstations. Can be passive, where there is no amplification of the signals; or
active, where the hubs are used like repeaters to provide an extension of the
cable that connects to a workstation.
LAN (Local Area Network) – A group of computers and associated devices that
share a common communications line and typically share the resources of a
single processor or server within a small geographic area (for example, within
an office building).
IEEE (Institute of Electrical and Electronics Engineers) - The IEEE fosters the
development of standards that often become national and international
standards. The organization publishes a number of journals, has many local
chapters, and has several large societies in special areas, such as the IEEE
Computer Society.
Latency - The time delay between when the first bit of a packet is received and
the last bit is forwarded.
Link Quality - The quality of data being received.
IEEE 802.11 - Industry standard that enables wireless LAN hardware from
different manufacturers to communicate.
MAC Address (Media Access Control Address) - A unique number assigned
by the manufacturer to any Ethernet networking device, such as a network
adapter, that allows the network to identify it at the hardware level.
Infrastructure Mode - A mode of operation of the 802.11b wireless protocol
that allows all computers on a wired and wireless network to share a peripheral,
such as a printer or high speed Internet Access.
Mbps (Megabits per Second) – One million bits per second; a unit of
measurement of the speed of data transmission.
IP Address - In the most widely installed level of the Internet Protocol (IP)
today, and IP address is a 32-binary digit number that identifies each sender or
receiver of information that is sent in packets across the Internet. When you
request an HTML page or send e-mail, the Internet Protocol part of TCP/IP
includes your IP address in the message (actually, in each of the packets if
more than one is required) and sends it to the IP address that is obtained by
looking up the domain name in the Uniform Resource Locator you requested or
in the e-mail address you’re sending a note to. At the other end, the recipient
can see the IP address of the Web page requestor or the e-mail sender and
can respond by sending another message using the IP address it received.
NAT (Network Address Translation) – The translation of an Internet Protocol
address (IP address) used within one network to a different IP address known
within another network. One network is designated the inside network and the
other is the outside.
Network - A system that transmits any combination of voice, video, and/or data
between users.
51
52
Download from Www.Somanuals.com. All Manuals Search And Download.
NIC (Network Interface Card) – A board installed in a computer system, usually
a PC, to provide network communication capabilities to and from that computer
system. Also called an adapter.
PPTP (Point-to-Point Tunneling Protocol) – A protocol (set of communication
rules) that allows corporations to extend their own corporate network through
private “tunnels” over the public Internet. Effectively, a corporation uses a wide-
area network as a single large local area network. A company no longer needs
to lease its own lines for wide-area communication but can securely use the
public networks. This kind of interconnection is known as a virtual private
network (VPN).
Packet Filtering - Discarding unwanted network traffic based on its originating
address or range of addresses or its type (e-mail, file transfer, etc.).
Print Server - A hardware device that enables a printer to be located anywhere
in the network.
PCI (Peripheral Component Interconnect) – A peripheral bus commonly used in
PCs, Macintoshes and workstations. It was designed primarily by Intel and first
appeared on PCs in late 1993. PCI provides a high-speed data path between
the CPU and peripheral devices (video, disk, network, etc.). There are typically
three of four PCI slots on the motherboard. In a Pentium PC, there is generally
a mix of PCI and ISA slots or PCI and EISA slots. Early on, the PCI bus was
known as a “local bus.” PCI allows IRQs to be shared, which helps to solve the
problem of limited IRQs available on a PC. For example, if there were only one
IRQ left over after ISA devices were given their required IRQs, all PCI devices
could share it. In a PCI-only machine, there cannot be insufficient IRQs, as all
can be shared.
RIP (Routing Information Protocol) – A simple routing protocol that is part of the
TCP/IP protocol suite. It determines a route based on the smallest hop count
between source and destination. RIP is a distance vector protocol that routinely
broadcasts routing information to its neighboring routers and is known to waste
bandwidth.
AppleTalk, DECnet, TCP/IP, NetWare, and VINES all use
incompatible versions of RIP.
RJ-11 (Registered Jack-11) – A telephone connector that holds up to six wires.
The RJ-11 is the common connector used to plug a telephone into a wall.
PCMCIA - The PCMCIA (Personal Computer Memory Card International
Association) is an industry group organized in 1989 to promote standards for a
credit card-size memory or I/O device that would fit into a personal computer,
usually a notebook or laptop computer.
RJ-45 - A connector similar to a telephone connector that holds up to eight
wires, used for connecting Ethernet devices.
Router - Protocol-dependent device that connects sub networks together.
Routers are useful in breaking down a very large network into smaller sub
networks; they introduce longer delays and typically have much lower
throughput rates than bridges.
Peer-to-Peer Networking – Allows users to share local resources between
PCs without needing an access point or router.
Ping (Packet Internet Groper) – An Internet utility used to determine whether a
particular IP address is online. It is used to test and debug a network by
sending out a packet and waiting for a response.
Server - Any computer whose function in a network is to provide user access to
files, printing, communications, and other services.
Plug-and-Play – The ability of a computer system to configure expansion
boards and other devices automatically without requiring the user to turn off the
system during installation.
Signal Strength – The amount of electromagnetic energy is present.
receiver (such as the one in your access point determines the strength of the
signal for each wireless channel.
A
Port – A pathway into and out of the computer of a network device such as a
switch or router. For example, the serial and parallel ports on a personal
computer are external sockets for plugging in communications lines, modems,
and printers.
Software – Instructions for the computer. A series of instructions that performs
a particular task is called a “program.” The two major categories of software
are “system software” and “application software.” System software is made up
of control programs such as the operating system and database management
system (DBMS). Application software is any program that processes data for
the user. A common misconception is that software is data. It is not, software
tells the hardware how to process the data.
PPPoE (Point to Point Protocol over Ethernet) – A method used mostly by DSL
providers for connecting personal computers to a broadband modem for
Internet access. It is similar to how a dial-up connection works but at higher
53
54
Download from Www.Somanuals.com. All Manuals Search And Download.
SOHO (Small Office/Home Office) – Market segment of professionals who work
at home or in small offices.
UDP (User Datagram Protocol) – A communications method (protocol) that
offers a limited amount of service when messages are exchanged between
computers in a network that uses the Internet Protocol (IP). UDP is an
alternative to the Transmission Control Protocol (TCP) and, together with IP, is
sometimes referred to as UDP/IP. Like the Transmission Control Protocol, UDP
uses the Internet Protocol to actually get a data unit (called a datagram) from
one computer to another. Unlike TCP, however, UDP does not provide the
service of dividing a message into packets (datagrams) and reassembling it at
the other end. Specifically, UDP doesn’t provide sequencing of the packets that
the data arrives in. This means that the application program that uses UDP
must be able to make sure that the entire message has arrived and is in the
right order. Network applications that want to save processing time because
they have very small data units to exchange (and therefore very little message
reassembling to do) may prefer UDP to TCP.
Static IP Address - A permanent IP address that is assigned to a node in a
TCP/IP network.
Static Routing - Forwarding data in a network via a fixed path. Static routing
cannot adjust to changing line conditions as can dynamic routing.
Subnet Mask - The method used for splitting IP networks into a series of
subgroups, or subnets. The mask is a binary pattern that is matched up with
the IP address to form part of the host ID address field into a field for subnets.
Switch – 1. A data switch connects computing devices to host computers,
allowing a large number of devices to share a limited number of ports.
2. A device for making, breaking, or changing the connections in an electrical
circuit.
Upgrade – To replace existing software of firmware with a newer version.
Upload – To send a file transmitted over a network. In a communications
session, upload means transmit, and download means receive.
TCP (Transmission Control Protocol) – A method (protocol) used along with the
Internet Protocol (IP) to send data in the form of message units between
computers over the Internet. While IP takes care of handling the actual delivery
of the data, TCP keeps track of the individual units of data (called packets) that
a message is divided into for efficient routing through the Internet.
URL (Uniform Resource Locator) – The address that defines the route to a file
on the Web or any other Internet facility. URLs are typed into the browser to
access Web pages, and URLs are embedded within the pages themselves to
provide the hypertext links to other pages.
TCP/IP (Transmission Control Protocol/Internet Protocol)
-
The basic
communication language or protocol of the Internet. It can also be used as a
communication protocol in a private network (either an intranet or an extranet).
When you are set up with access to the Internet, your computer is uses the
TCP/IP protocol.
VLAN (Virtual LAN) – A logical association that allows users to communicate as
if they were physically connected to a single LAN, independent of the actual
physical configuration of the network.
WAN (Wide-Area Network) - A communications network that covers a wide
geographic area, such as a state or country.
TFTP (Trivial File Transfer Protocol) – A version of the TCP/IP FTP protocol that
has no directory or password capability.
WEP (Wired Equivalent Privacy) – A data privacy mechanism based on 64-bit
and 128-bit shared key algorithms, as described in the IEEE802.11 standard.
Throughput - The amount of data moved successfully from one place to
another in a given time period.
Topology - A network’s topology is a logical characterization of how the devices
on the network are connected and the distances between them. The most
common network devices include hubs, switches, routers, and gateways.
Most large networks contain several levels of interconnection, the most
important of which include edge connections, backbone connections, and wide-
area connections.
WINIPCFG - Configuration utility based on the Win32 API for querying,
defining, and managing IP addresses within a network. A commonly used utility
for configuring networks with static IP addresses.
Workgroup - Two or more individuals that share files and databases.
55
56
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
57
58
Download from Www.Somanuals.com. All Manuals Search And Download.
|