TRUE FOOD SERVICE EQUIPMENT, INC.
2001 East Terra Lane • P.O. Box 970 • O’Fallon, Missouri 63366
(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152
Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471
INSTALLATION MANUAL FOR
TMC UNITS (MILK COOLERS)
TABLE OF CONTENTS
TMC-34-S
Safety Information
Safety Precautions
Proper Disposal
1
2
3
3
Connecting Electricity
Adapter Plugs
Installation / Operation Instructions
Ownership
4
4
4
5
6
7
8
Required Tools
Uncrating
Locating & Leveling Cabinet
Electrical Instructions
Wire Gauge Chart
TMC-49-S
Start-up & Shelf Installation
Maintenance, Care & Cleaning
Cleaning Condenser Coil
9-10
Stainless Steel Equipment Care & Cleaning 11-12
Temperature Control Adjustment
Warranty (U.S.A. & Canada Only!)
13
14
*Spanish, German, and French versions included.
TMC-58-S
CONGRATULATIONS!
You have just purchased the finest commercial
refrigerator available. You can expect many years of
trouble-free operation.
M I L K C O O L E R S
12/7/07-2k SB #912629
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
How to Maintain Your
Refrigerator to Receive the Most
Efficient and Successful Operation
You have selected one of the finest commercial refrigeration units
made. It is manufactured under strict quality controls with only the
best quality materials available. Your TRUE cooler when properly
maintained will give you many years of trouble-free service.
WARNING!
Use this appliance for its intended purpose as described
in this Owner Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the
following:
This refrigerator must be properly installed and
located in accordance with the Installation
Instructions before it is used.
NOTE: We strongly recommend that any
servicing be performed by a qualified
individual.
Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
Unplug the refrigerator before cleaning and
making repairs.
Setting temperature controls to the 0 position
does not remove power.
Do not touch the cold surfaces in the refrigera-
tor compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
Keep fingers out of the“pinch point”areas;
clearances between the doors and between the
doors and cabinet are necessarily small; be
careful closing doors when children are in the
area.
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
DANGER!
RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE
REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous… even if they will sit for“just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help pre-
vent accidents.
Refrigerant Disposal
Your old refrigerator may have a cooling system
that uses“Ozone Depleting ”chemicals. If you are
throwing away your old refrigerator, make sure the
refrigerant is removed for proper disposal by a
qualified service technician. If you intentionally
release any refrigerants you can be subject to
fines and imprisonment under provisions of the
environmental regulations.
Before You Throw Away Your Old Refrigerator
or Freezer:
Take off the doors.
Leave the shelves in place so that children may
not easily climb inside.
USE OF EXTENSION CORDS
NEVER USE AN EXTENSION CORD! TRUE will not warranty any refrigerator that has been
connected to an extension cord.
2
2
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to mini-
mize the possibility of electric shock hazard from
this appliance.
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
Have the wall outlet and circuit checked by a quali-
fied electrician to make sure the outlet is properly
grounded.
If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it
replaced with the properly grounded 3-prong wall
outlet.
When removing the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
The refrigerator should always be plugged into it’s
own individual electrical circuit, which has a volt-
age rating that matches the rating plate.
This provides the best performance and also pre-
vents overloading building wiring circuits which
USE OF ADAPTER PLUGS
(Adapter plugs are not permitted in Canada)
NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain condi-
tions, we strongly recommend against the use of an adapter plug.
North America Use Only!
NEMA plugs
TRUE uses these types of plugs.
If you do not have the right outlet
have a certified electrician install
the correct power source.
3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
INSTALLATION / OPERATION INSTRUCTIONS
OWNERSHIP
To insure that your unit works properly from the
first day, it must be installed properly. We highly
recommend a trained refrigeration mechanic and
electrician install your True equipment. The cost
of a professional installation is money well spent.
Before you start to install your True unit, carefully
inspect it for freight damage. If damage is discov-
ered, immediately file a claim with the delivery
freight carrier.
True is not responsible for damage incurred
during shipment.
REQUIRED TOOLS
Adjustable Wrench
Phillips Head Screwdriver
Level
UNCRATING
Step 1
Note: Keys for coolers with door locks are
located in warranty packets.
The following procedure is recommended for
uncrating the unit:
A. Remove the outer packaging, (cardboard and
bubbles or styrofoam corners and clear plastic).
Inspect for concealed damage.Again, immedi-
ately file a claim with the freight carrier if there
is damage.
B. Move your unit as close to the final location as
possible before removing the wooden skid.
C. Remove all tape securing the doors to the cool-
er, and any foam blocks between doors.
D. Remove any components (castors, floor racks,
etc.) packaged inside the cabinet.
REMOTE UNITS (This section applies to remotes
only!)
• Remote cabinets must be ordered as remote.
We do not recommend converting for a standard
self contained to remote system.
• Contact True Technical Service for BTU
requirements.
• No wiring necessary between cabinet and
condensing unit.
• All remote cabinets must be hard wired.
• No castors available.
• All remote condensing units purchased from
True are 208/230 volts single phase.
• All remote cabinets come standard using 404A
refrigerant.
If you have any questions regarding this sec-
tion, please call True at 1-(800)-325-6152.
• All remote units come standard with expansion
valve, liquid line solenoid, heated condensate
pan, and defrost timer when applicable.
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LOCATING
Step 2
35°
A. Remove skid by using a phillips head screwdriv-
F°
er and an adjustable wrench.
®
B. For easy removal from the skid, unscrew and
remove grill from the back of the cooler.
C. Remove the four brackets from the base of the
cooler.
D. Carefully move the cooler off the back of the
skid. Tilt the cooler backwards just enough to
remove the skid from under the cooler.
E. Free plug and cord from inside the lower rear of
the cooler (do not plug in).
F. Place grill back onto rear of the cooler.
G. The merchandiser should be placed close
enough to the electrical supply so that exten-
sion cords are never used.
Image 1
WARNING:
Compressor warranties are void if the
unit is more than 9ft. (2.7 m) from
plug-in connection.
LEVELING
Important Safeguard for installation of leg/castor (Images 1-5 demonstrate procedure)
Step 3
LEVELING CASTORS
A. Set unit in its final location. Be sure there is
adequate ventilation in your room. Under extreme
heat conditions, (100 F+, 38 C+), you may want to
install and exhaust fan.
Four sets of shims have been provided in warranty
packet for leveling castored units positioned on
uneven floors. Shims must be positioned between
cabinet and castor mounting plate. (See image 3)
WARNING:
If the cabinet is not level prop up one end of the
cabinet between castors with a 6”block.
(See image 4)
Warranty is void if ventilation is insufficient.
B. Proper leveling of your True cooler is critical to
operating success. Effective condensate removal
and door operation will be effected by leveling.
(See image 2)
Note:
Do not push block more than 5”
under cabinet.
C. When the cooler is in its final position adjust
the castors as needed to level the unit. The unit
should be leveled front to back and side to side
with a level. To insure proper ventilation for the
compressor, keep the cabinet 1”(2.54 cm) from
rear wall. 1”(2.54 cm) rubber bumpers are
attached to the back of some cabinets.
Loosen castor bolts with an adjustable wrench
enough to slide shims between the castor mount-
ing plate and cabinet bottom.
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LEVELING CASTORS CONTINUED....
Install the desired number of shims (in pairs as
shown in figure 3), making sure the slots in the
shim are in contact with the castor mounting bolts.
Tighten and secure the shims and castor(s).
Remove 6”block and check to determine if cabinet
is level.
35°
F°
®
Repeat process until cabinet is level.
D. Ensure that the drain hose or hoses are posi-
tioned in the pan.
Image 2
Image 4
Image 3
ELECTRICAL INSTRUCTIONS
CAUTION
Step 4
Voltage drops can occur due to long wire runs
from the voltage source. Consult the wiring chart
on page 7 to insure proper voltage.
A. Before your new unit is connected to a power
supply, check the incoming voltage with a volt-
meter. If anything less than 100% of the rated volt-
age for operation is noted, correct immediately.
WARNING
Compressor warranties are void if compressor
burns out due to low voltage.
B. All units are equipped with a 9 ft. (2.7m) serv-
ice cord, and must be powered at proper operating
voltage at all times. Refer to cabinet data plate for
this voltage.
WARNING
Power supply cord ground should not be
removed!
NOTE
True requires that a sole use circuit be dedicated
To reference wiring diagram - Remove lower rear
grill, wiring diagram is positioned inside on the
ballast box.
for the unit. Failure to do so voids warranty.
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
Wire Gauge for 2% Voltage Drop in Supply Circuits
115
Volt
Amps
Distance in Feet to Center of Load.
20
30
40
50
60
70
80
90
100
120
140
160
2
3
4
5
6
7
8
9
10
12
14
16
18
20
25
30
35
40
45
50
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
12
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
12
12
12
10
10
10
8
14
14
14
14
14
14
14
14
14
12
12
12
10
10
10
8
14
14
14
14
14
14
14
12
12
12
10
10
10
10
8
14
14
14
14
14
14
12
12
12
10
10
10
8
8
8
6
6
6
6
5
14
14
14
14
14
12
12
12
10
10
10
8
8
8
6
6
6
5
5
4
14
14
14
14
12
12
12
10
10
10
8
8
8
8
6
6
5
5
4
14
14
14
12
12
12
10
10
10
8
8
8
8
6
6
6
5
4
14
14
14
12
12
10
10
10
10
8
8
8
8
6
6
5
4
4
14
14
12
12
10
10
10
8
8
8
6
6
8
6
5
4
4
3
3
2
14
14
12
10
10
10
8
8
8
8
6
6
8
5
4
4
3
2
2
14
12
12
10
10
8
8
8
8
6
6
6
5
5
4
3
2
2
8
6
6
6
8
8
6
6
8
8
4
3
3
3
1
1
6
4
1
Wire Gauge for 2% Voltage Drop in Supply Circuits
230Volt
Amps
Distance in Feet to Center of Load.
20
30
40
50
60
70
80
90
100
120
140
160
5
6
7
8
9
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
12
10
10
10
10
14
14
14
14
14
14
14
14
14
14
14
14
12
12
12
10
10
10
8
14
14
14
14
14
14
14
14
14
14
14
12
12
10
10
10
8
14
14
14
14
14
14
14
14
14
12
12
12
10
10
10
8
14
14
14
14
14
14
14
14
12
12
10
10
10
10
8
14
14
14
14
14
14
14
12
12
12
10
10
10
8
8
6
6
6
5
5
4
14
14
14
14
14
14
12
12
12
10
10
10
8
8
8
6
6
5
5
4
4
14
14
14
14
14
12
12
12
10
10
10
10
8
8
6
6
6
5
4
4
3
14
14
14
14
12
12
12
10
10
10
10
8
8
8
6
6
5
5
4
3
14
14
14
12
12
13
10
10
10
8
8
8
6
6
6
5
4
4
14
14
12
12
12
10
10
10
8
8
8
6
6
6
5
4
4
2
2
1
1
14
12
12
12
10
10
10
8
8
8
8
6
6
5
5
4
3
2
2
1
10
12
14
16
18
20
25
30
35
40
50
60
70
80
90
100
6
6
6
6
5
5
6
6
6
6
8
8
6
6
3
3
2
8
8
6
3
1
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
STARTUP
Step 5
RECOMMENDATION
Before loading product we recommend you
run your True unit empty for two to three
days. This allows you to be sure electrical
wiring and installation are correct and no
shipping damage has occurred. Every True
cooler is tested in our plants for 24 hours to
thoroughly check all components. Unless
they meet our strict standards, they do not
pass our final quality control inspection.
Remember, our factory warranty does not
cover product loss!
A. The compressor is ready to operate. Plug in the
cooler.
B. Check the temperature control setting in the
upper right of the cabinet interior. The setting
should be at #5.
C. Excessive tampering with the control could
lead to service difficulties. Should it ever become
necessary to replace temperature control, be sure it
is ordered from your True dealer or recommended
service agent.
D. Good air flow in your True unit is critical. Be
careful to load product so that it neither presses
against the back wall, nor comes within four inches
of the evaporator housing. Refrigerated air off the
coil must circulate down the back wall.
REPLACEMENT PARTS
TRUE maintains a record of the cabinet serial
number for your cooler. If at any time during
the life of your cooler, a part is needed, you
may obtain this part by furnishing the model
number and serial number to the company
from whom you purchased the cooler.
NOTE
If the cooler is disconnected or shut off, wait
five minutes before starting again.
SHELF INSTALLATION
Wire floor racks should be positioned on the floor
of the cooler with legs facing down.
8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
MAINTENANCE, CARE & CLEANING
CLEANING THE CONDENSER COIL
When using electrical appliances, basic safety precautions should be followed, including the following:
REQUIRED TOOLS:
• Phillips Screwdriver
• Stiff Bristle Brush
• Adjustable Wrench
• Vacuum Cleaner
Step 1
Disconnect power to unit.
Image 3.
Step 2
Take off rear lower grill assembly by removing (2)
side screws.
Step 3
Remove bolts connecting frame rail cross bar to
allow access to compressor.
Step 4
Remove bolts anchoring compressor assembly to
frame rails and carefully slide out. (tube
connections are flexible)
Step 5
Clean off accumulated dirt from condensing coil
with a stiff bristle brush.
Image 4.
Step 6
Lift W.R. Board cover above fan at plastic plugs and
carefully clean condenser coil and fan blades.
Step 7
After brushing condenser coil vacuum dirt from
coil, and interior floor.
Step 8
Replace cardboard cover. Carefully slide
compressor assembly back into position and
replace bolts.
Step 9
Reinstall rear grill assembly onto unit with
appropriate screws. Tighten all screws.
Step 10
Connect unit to power and check to see if
compressor is running.
9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
IMPORTANT WARRANTY INFORMATION
Condensers accumulate dirt and require cleaning every 30 days. Dirty condensers result in compressor
failure, product loss, and lost sales... which are not covered by warranty.
If you keep the Condenser clean you will minimize your service expense and lower your electrical costs.
The Condenser requires scheduled cleaning every thirty days or as needed.
Air is pulled through the Condenser continuously, along with dust, lint, grease, etc.
A dirty Condenser can result in NON-WARRANTEED part & Compressor Failures, Product Loss, and
Lost Sales.
Proper cleaning involves removing dust from the Condenser. By using a soft brush, or vacuuming the
Condenser with a shop vac, or using CO2, nitrogen, or pressurized air.
If you cannot remove the dirt adequately, please call your refrigeration service company.
On most of the reach-in units the condenser is accessible in the rear of the unit. You must remove the
cabinet grill to expose the Condenser.
The Condenser looks like a group of vertical fins. You need to be able to see through the condenser for
the unit to function at maximum capacity. Do not place filter material in front of condensing coil. This
material blocks air-flow to the coil similar to having a dirty coil.
THE CLEANING OF THE CONDENSER IS NOT
COVERED BY THE WARRANTY!
Air
flow
HOW TO CLEAN THE CONDENSER:
1. Disconnect the electrical power to the unit.
2. Remove the louvered grill.
Condensing Unit
Condenser
3. Vacuum or brush the dirt, lint, or debris from the finned condenser coil.
4. If you have a significant dirt build up you can blow out the condenser with compressed air. (CAU-
TION MUST BE USED to avoid eye injury. Eye protection is recommended.)
5. When finished be sure to replace the louvered grill. The grill protects the condenser.
6. Reconnect the electrical power to the unit.
If you have any questions, please call True Manufacturing at 636-240-2400 or 800-325-6152 and ask for
the Service Department. Service Department Availability Monday-Friday 7:30 a.m. to 5:30p.m.
and Saturday 7:45 a.m. to 11:45 a.m. CST.
10
10
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
Stainless Steel Equipment Care and Cleaning
CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless
steel surfaces.
Stainless Steel Opponents
There are three basic things which can break down your stainless steel’s passivity layer and allow
corrosion to rear its ugly head.
1) Scratches from wire brushes, scrapers, and steel pads are just a few examples of items that can be
abrasive to stainless steel’s surface.
2) Deposits left on your stainless steel can leave spots. You may have hard or soft water depending on
what part of the country you live in. Hard water can leave spots. Hard water that is heated can
leave deposits if left to sit too long. These deposits can cause the passive layer to break down and
rust your stainless steel. All deposits left from food prep or service should be removed as soon as
possible.
3) Chlorides are present in table salt, food, and water. Household and industrial cleaners are the worst
type of chlorides to use.
8 steps that can help prevent rust on stainless steel:
1. Using the correct cleaning tools
Use non-abrasive tools when cleaning your stainless steel products. The stainless steel’s passive layer
will not be harmed by soft cloths and plastic scouring pads. Step 2 tells you how to find the
polishing marks.
2. Cleaning along the polish lines
Polishing lines or“grain”are visible on some stainless steels. Always scrub parallel to visible lines on
some stainless steels. Use a plastic scouring pad or soft cloth when you cannot see the grain.
3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners
While many traditional cleaners are loaded with chlorides, the industry is providing an ever
increasing choice of non-chloride cleaners. If you are not sure of your cleaner’s chloride content
contact your cleaner supplier. If they tell you that your present cleaner contains chlorides, ask if
they have an alternative. Avoid cleaners containing quaternary salts as they can attack stainless steel,
causing pitting and rusting.
4. Water Treatment
To reduce deposits, soften the hard water when possible. Installation of certain filters can remove
corrosive and distasteful elements. Salts in a properly maintained water softener can be to your
advantage. Contact a treatment specialist if you are not sure of the proper water treatment.
5. Maintaining the cleanliness of your food equipment
Use cleaners at recommended strength (alkaline, alkaline chlorinated or non-chloride). Avoid
build-up of hard stains by cleaning frequently. When boiling water with your stainless steel
equipment, the single most likely cause of damage is chlorides in the water. Heating any cleaners
containing chlorides will have the same damaging effects.
6. Rinse
When using chlorinated cleaners you must rinse and wipe dry immediately. It is better to wipe
standing cleaning agents and water as soon as possible. Allow the stainless steel equipment to air
dry. Oxygen helps maintain the passivity film on stainless steel.
7. Hydrochloric acid (muriatic acid) should never be used on stainless steel
8. Regularly restore/passivate stainless steel
11
11
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
Stainless Steel Equipment Care and Cleaning
Recommended cleaners for certain situations / environments of stainless steel
A) Soap, ammonia and detergent medallion applied with a cloth or sponge can be used for routine
cleaning.
B) Arcal 20, Lac-O-Nu Ecoshine applied provides barrier film for fingerprints and smears.
C) Cameo,Talc, Zud First Impression is applied by rubbing in the direction of the polished lines for
stubborn stains and discoloring.
D) Easy-off and De-Grease It oven aid are excellent for removals on all finishes for grease-fatty acids,
blood and burnt-on foods.
E) Any good commercial detergent can be applied with a sponge or cloth to remove grease and oil.
F) Benefit, Super Sheen, Sheila Shine are good for restoration / passivation.
NOTE:
The use of stainless steel cleaners or other such solvents is not
recommended on plastic parts. Warm soap and water will suffice.
To clean interior of cooler move the unit close
to a floor drain. Remove floor racks from inside
of the unit. Wash interior of the tank. At the
rear of the unit and below the grill there is a
tank drain plug that will need to be removed to
release the waste from inside of the unit. After
all waste material is gone from the tank, reinsert
the tank drain plug in the rear of the unit.
See photo 1-2 below
Tank Drain
1
2
12
12
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
TEMPERATURE CONTROL ADJUSTMENT FOR
HIGH ALTITUDE ONLY!
TERMS:
___________ STEP 4 ___________
For high elevation installations, it
may be necessary to "warm-up"
the set points. To make the
adjustment, insert the appropri-
ate tool in each adjustment
screw and turn 1/4 of a revolu-
tion clockwise (to the right).
This procedure will adjust both
the cut-in and cut-out about 2°F
warmer.
Cut-out - Temperature sensed by
the controller that shuts the
compressor off.
Cut-in - Temperature sensed by
the controller that turns the
compressor on.
REQUIRED TOOLS
• Phillips Head Screwdriver
• 5/64" or 2 mm Allen Wrench
• T-7 Torx Wrench
___________ STEP 5 ___________
Make sure to reconnect the pink
wire to the proper spade
terminal when reinstalling.
___________ STEP 1 ___________
Unplug the cooler.
___________ STEP 2 ___________
Remove the screws that secure
the temperature control to the
inset box
___________ STEP 3 ___________
Danfoss Temperature Control (High Altitude Adjustment Only!)
Pull out gently from cabinet.
Cut-out Adjustment Screw Allen (5/64"
or 2 mm) (clockwise for warmer)
NOTE:
Cut-in Adjustment Screw Torx (T-7)
(clockwise for warmer)
Mechanical temperature
controllers are affected when
functioning at high altitude.
The cut-in and cut-out
temperatures will be colder
than when the controller
functions closer to sea level
Compressor Connection
Compressor Connection
(double terminal)
13
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TRUE REFRIGERATIONTM
True Food Service Equipment, Inc.
WARRANTY INFORMATION (U.S.A & CANADA ONLY!)
MADE IN
U.S.A.
SINCE 1945
ONE YEAR PARTS & LABOR WARRANTY
TRUE warrants to the original purchaser of every new TRUE refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or
workmanship, under normal and proper use and maintenance service as specified by TRUE and upon proper installation and start-up in accordance with
the instruction packet supplied with each TRUE unit. TRUE’s obligation under this warranty is limited to a period of one (1) year from the date of original
installation or 15 months after shipment date from TRUE, whichever occurs first.
Any part covered under this warranty that are determined by TRUE to have been defective within one (1) year of original installation or fifteen (15)
months after shipment date from manufacturer, whichever occurs first, is limited to the repair or replacement, including labor charges, of defective parts or
assemblies. The labor warranty shall include standard straight time labor charges only and reasonable travel time, as determined by TRUE.
ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY
In addition to the one (1) year warranty stated above, TRUE warrants its hermetically and semi-hermetically sealed compressor to be free from defects
in both material and workmanship under normal and proper use and maintenance service for a period of four (4) additional years from the date of origi-
nal installation but not to exceed five (5) years and three (3) months after shipment from the manufacturer.
Compressors determined by TRUE to have been defective within this extended time period will, at TRUE’s option, be either repaired or replaced with a
compressor or compressor parts of similar design and capacity.
The four (4) year extended compressor warranty applies only to hermetically and semi-hermetically sealed parts of the compressor and does not
apply to any other parts or components, including, but not limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers, motor
starting equipment, fan assembly or any other electrical component, etcetera.
404A/134A COMPRESSOR WARRANTY
The four year compressor warranty detailed above will be voided if the following procedure is not carefully adhered to:
1. This system contains R404A or R134A refrigerant and polyol ester lubricant. The polyol ester lubricant has rapid moisture absorbing qualities. If long
exposure to the ambient conditions occur, the lubricant must be removed and replaced with new. For oil amounts and specifications please call True
technical service department (800-325-6152). Failure to comply with recommended lubricant specification will void the compressor warranty.
2. Drier replacement is very important and must be changed when a system is opened for servicing. A drier using XH-7 desiccant or an exact replace-
ment solid core drier must be used. The new drier must also be the same capacity as the drier being replaced.
3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained.
WARRANTY CLAIMS
All claims for labor or parts must be made directly through TRUE. All claims should include: model number of the unit, the serial number of the cabinet,
proof of purchase, date of installation, and all pertinent information supporting the existence of the alleged defect.
In case of warranty compressor, the compressor model tag must be returned to TRUE along with above listed information.
Any action or breach of these warranty provisions must be commenced within one (1) year after that cause of action has occurred.
WHAT IS NOT COVERED BY THIS WARRANTY
TRUE’s sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty
neither assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty.
NO CONSEQUENTIAL DAMAGES. TRUE IS NOT RESPONSIBLE FOR ECONOMIC LOSS; PROFIT LOSS; OR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES,
INCLUDING WITHOUT LIMITATION, LOSSES OR DAMAGES ARISING FROM FOOD OR PRODUCT SPOILAGE CLAIMS WHETHER OR NOT ON ACCOUNT OF REFRIG-
ERATION FAILURE.
WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original purchaser/user to whom delivered. ANY
SUCH ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANTIES HEREIN MADE AND SHALL VOID ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WAR-
RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IMPROPER USAGE. TRUE ASSUMES NO LIABILITY FOR PARTS OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER DAMAGES RESULTING FROM
IMPROPER USAGE OR INSTALLATION OR FAILURE TO CLEAN AND/OR MAINTAIN PRODUCT AS SET FORTH IN THE WARRANTY PACKET PROVIDED WITH THE UNIT.
ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE, FLOOD, ACTS OF GOD. TRUE is not responsible for
the repair or replacement of any parts that TRUE determines have been subjected after the date of manufacture to alteration, neglect, abuse, misuse,
accident, damage during transit or installation, fire, flood, or act of God.
IMPROPER ELECTRICAL CONNECTIONS. TRUE IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF FAILED OR DAMAGED COMPONENTS RESULTING
FROM ELECTRICAL POWER FAILURE, THE USE OF EXTENSION CORDS, LOW VOLTAGE, OR VOLTAGE DROPS TO THE UNIT.
NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE: THERE ARE NO OTHER WARRANTIES, EXPRESSED, IMPLIED OR
STATUTORY, EXCEPT THE ONE (1) YEAR PARTS & LABOR WARRANTY AND THE ADDITIONAL FOUR (4) YEAR COMPRESSOR WARRANTY AS DESCRIBED ABOVE.
THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS FOR A PAR-
TICULAR PURPOSE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
OUTSIDE U.S.: This warranty does not apply to, and TRUE is not responsible for, any warranty claims made on products sold or used outside the United
States.
REMOTE CONDENSERS: True warrants the original purchaser of the remote cabinet one year parts and labor coverage for all cabinet parts thereof to
be free from defects in material or workmanship, under normal and proper use and maintenance service, as specified by True. This warranty is limited to
the cabinet only. True assumes no liability for remote condensing units.
14
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|