B/W CCD Camera
Model CS8560D
Specifications
(Ver.1.0)
Contents
1. Product Description ························· 6
2. Features·············································· 6
3. Configuration···································· 7
4. Option Unit········································ 7
5. Operation Mode································ 7
6. Specifications····································· 24
7. Timing Chart····································· 32
8. External View Drawing ··················· 40
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
Don’t place things or materials on the unit.
Ingress of foreign materials such as metallic things and liquid into the unit may
cause a fire or an electric shock.
Do not put the product in an unstable, slanting and/or vibrated place.
Drop and/or fail of the product may cause injury.
Do not touch the power cord or other connection cables during a
thunderstorm.
This might cause electric shock.
Use the specified power supply.
Use of an unspecified power supply may result in fire or electric shock.
Do not be handled roughly, damaged, fabricated, bent forcefully, pulled,
twisted, bundled, placed under heavy objects or heated the power cord ,
connection cable.
Otherwise, fire or electric shock may result.
CAUTION
Note the following instructions when installing.
-Do not wrap the product in an inflammable material, such as cloth.
-Do not put the product in a narrow space, since the heat generated from the
product may be difficult to emanate.
If you do not follow the above, the heat generated by the product may cause
fire.
Avoid setting in humid, smoky, vaporized or dusty places. A fire or an
electric shock may occur in such places.
This may cause fire and/or electric shock.
Do not put the product in direct sunshine and/or high temperature.
The temperature inside the product may cause fire.
Use the specified DC power cable or connection cable.
Otherwise, a fire or an electric shock may occur.
Turn OFF the power in the case of connection.
Turn OFF the power in the case of connection of power cable or connection
cable.
Otherwise, an electric shock or a malfunction may occur.
Do not expose its camera head to any intensive light (such as direct
sunlight).
Otherwise, its inner image pickup device might get damaged.
Avoid short-circuiting signal output.
Otherwise, a malfunction may occur.
Avoid giving a strong shock against the camera body.
It might cause a breakdown or damage.
If your camera is used in a system where its camera connector is subjected to
strong repetitive shocks, its camera connector is possible to break down. If
you intend to use your camera in such a situation, if possible, bundle and fix
a camera cable in the place near the camera, and do not transmit a shock to
the camera connector.
Ask your dealer to perfom a periodical check and internal cleaning
(approx. once every five years).
Dust inside the product may cause fire and/or trouble. For check and cleaning
cost, please consult your dealer.
3
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
DISCLAIMER (LIMITED WARRANTY)
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by
the user in any of the following cases;
z Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether
intentional or accidental; use under extreme operating conditions.
z Malfunction or non-function resulting in indirect, additional or consequential damages,
including but not limited to loss of expected income and suspension of business activities.
z Incorrent use not in compliance with instructions in this instruction specifications and manual.
z Malfunctions resulting from misconnection to other equipment.
z Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
z Notwithstanding the foregoing, Teli’s liabilities shall not, in any circumstances, exceed the
purchase price of the product.
z About the item which does not have a publication in the specifications and manual of this
product, it considers as the outside for a guarantee.
RESTRICTION FOR USE
z Should the equipment be used in the following conditions or environments, give consideration
to safelty measures and inform us of such usage:
1. Use of the equipment in the conditions or environment contrary to those specified, or use
outdoors.
2. Use of the equipment in applications sxpected to cause potential hazard to people or
propety, which require special safety measures to be adopted.
z This product can be used under diverse operating conditions. Determination of applicability of
equipment or devices concerned shall be determined after analysis or testing as necessary by
the designner of such equipment or devices, or personnel related to the specifications. Such
designer or personnel shall assure the performance and safety of the equipment or devices.
z This product is not designed or manufactured to be used for control of equipment directly
concerned with human life (*1) or equipment relating to maintenance of of public
services/functions involving factors of safety (*2). Therefore, the product shall not be used for
such applications.
(*1): Equipment directly concerned with human life refers to.
- Medical equipment such as life-support systems, equipment for prerating theaters.
- Exhaust control equipment for exhaust gases such as toxic fumes or smoke.
- Equipment mandatory to be installed by various laws and regulations such as the Fire
Act or Building Standard Law
- Equipment related to the above.
(*2) : Equipment relating to maintenance of public services/functions involving factors of
safety refers to.
- Traffic control systems for air transportations, railways, roads, or marine
transportation
- Equipment for nuclear power generation
- Equipment related to the above
4
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS ON USE
z Carefully handle the units.
Do not drop, or give a strong shock or vibration to the camera. This may cause problems. Treat
the camera cables carefully to prevent cable problems, such as cable breakdown and loosened
connections.
z Operating ambient temperature and humidity.
Do not use the camera in places where temperature and humidity exceed the specifications.
Picture quality will lower and internal parts may be damaged.
Be particularly careful when using in places exposed to direct sunlight. When shooting in hot
places, depending on the conditions of the object and the camera (for example when the gain is
increased), noise in the form of vertical strips or white dots may occur. This is not a
malfunction.
z Restriction for the lens combination
This camera might form a ghost to image area depending on the combination of a lens and an
illumination with this camera. But this is not a failure of this camera. Therefore, please check
the combination of the lens and the illumination with this camera when use.
When mounting a lens, take extra caution so that the lens is not tilted, nor does flaw exist at
the lens-mount-screw part. Also check to confirm that no dirt nor other foreign object is put
inside
Improper mounting might cause the parts to become locked.
z Do not shoot under intense light.
Avoid intense light such as spot light on part of the screen because it may cause blooming or
smears. If intense light falls on the screen, vertical stripes may appear on the screen, but this is
not a malfunction.
z Do not expose the camera’s image-pickup-plane to sunlight or other intense light directly.
Its inner CCD (charge-coupled device) might be damaged.
z Moire
When thin stripe patterns are shot, stripe patterns that are not actually there (moire) may
appears as interference stripes. This is not a malfunction.
z Undesirable noise
If the camera or the cables are located near something which emit strong magnetism or near
something which emit strong electric wave, undesirable noise may appear on the screen. In
such a case, try to change the location of the camera or the cable wiring.
z Handling of the protection cap
When the camera is not in use, put a lens-cap onto the camera head for protection of the
image-pickup-plane.
z When not using the camera for a longtime.
Stop supplying power for safety.
z When cleaning the camera
Always turn off the power and clean with a piece of soft dry cloth.
To remove stubborn stains, use a soft cloth soaked in diluted acid-free detergent. Do not use
alcohol, benzine, thinner, etc. If used, coating and printed letters may be discolored.
In case the image-pickup-plane should be settled with fine dust, dirt, or scratched, ask your
dealer for technical advice.
z Wastes of this product should be separated and discarded in compliance with the various
national and local ordinances.
5
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
1. PRODUCT DESCRIPTION
Model CS8560D is an integrated type B/W CCD camera with a VGA format all-pixel-data readout
CCD. This model has twice greater driving frequency of conventional cameras to achieve
fast-speed data-processing. The model is suited for high-speed, high-resolution image processing
use. Its compact, light-weight body is ideal for system integration.
2. FEATURES
(1) Double-speed scan
This model reads out image-data twice as fast as conventional cameras do.
(2) All pixel's data readout
With its built-in all-pixel-data-readout CCD, this model can read out image-data just in
approximately 1/60 sec. A frame-shutter reads out all data even under RTS (Random Trigger
Shutter) mode.
(3) High vertical resolution
As all pixel's data are read out even under RTS mode (in 1/60 sec.), images with no
deterioration in vertical resolution are obtained.
(4) Square grid pattern CCD
Pixel's in CCD are aligned in square grid pattern. This makes it easier to perform computation
correctly for image processing use.
(5) External Sync.
The camera is switched over to external synchronization operation automatically when external
HD signal is input.
(6) Random trigger shutter function
With a built-in RTS, the camera’s CCD starts light-exposure in synchronization with external
trigger signals. This function enables the camera to capture fast-moving subjects at constant
position for precise image processing.
(7) Restart / Reset
Under the restart / reset mode, this model can capture images at an arbitrary timing cued by
external VD signal.
(8) Multiple shutter
With this shutter, this model capture images at an arbitrary timing cued by external trigger
signal, and then outputs video at an arbitrary timing cued by external VD signal.
(9) Partial-scan
Under the partial scan mode, only 1/2 or 1/4 screen center portion of image information is read
out, resulting in a faster operation.
(10) Ultra-compact & light-weight camera head
The model features its ultra-compact and light-weight camera head, freeing you from your
integration-space-problem. In addition, it has an excellent shock and vibration resistance.
6
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
3. CONFIGURATION
(1) Camera body··································································· 1
(2) Accessory
Operation Manual(Japanese) ··········································· 1
Operation Manual(English) ············································· 1
4. OPTION UNIT
(1) DC SYNC IN cable ············Model name : CPRC3700 [2m,3m,5m,10m]
(2) Camera adapter ··················Model name : CA170
(3) Camera-mounting kit···········Model name : CPT8560
(4) Camera-connector fixing hardware
*Contact your dealer / distributor for details of option units.
*Conformity of an option part and EMC conditions
About the conformity of EMC standard of this machine, it has guaranteed in the
conditions combined with the above-mentioned option part.
When used combined parts other than specification of our company, I ask you to have
final EMC conformity checked of a visitor with a machine and the whole equipment.
5. OPERATION MODE
(1) GAIN selection (Camera rear-panel SW)
Switches sensitivity setting
(1-1) FIX------------------- Factory-prefixed gain
(1-2) MANU--------------- Gain is adjustable via the manual gain potentiometer (M.GAIN)
(2) Video output mode selection (Camera rear-panel DIP SW)
Switches video format
(2-1) 1/60: 1/60s ---------- Non-interlace mode
As all pixels are read out in 1/60s, you will get images with the
higher V resolution.
(2-2) 1/120: 1/120s ------- 2:1 interlace MIX mode
As vertical pixels are added in readout, the sensitivity is same as
that of 1/60s non-interlace mode during electronic shutter OFF.
Twice greater sensitivity is obtained under shutter-speed range of
1/200 – 1/20000.
(3) RTS (Random Trigger Shutter) exposure selection (Camera rear-panel DIP SW)
Switches light exposure mode under RTS mode
(3-1) FIX mode ----------- Rear DIP SW
Exposure-time control via rear-panel DIP switch
(3-2) PULSE W mode---- TRIG signal pulse width control
Exposure-time control via TRIG signal pulse width
7
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Shutter mode selection (Camera rear-panel DIP SW or TRIG signal IN [Automatic])
Switches shutter mode
(4-1) NOR mode ---------- Normal electronic shutter
Exposure control via internal sync signal
High-speed shutter: From 1/20,000s through OFF (8 position)
(4-2) RTS mode----------- Random trigger shutter
Exposure control via ext. trigger or ext. sync input
Timing charts are shown below. (TRIG timing: Positive)
Notes: * RTS selection is automatic with TRIG status
** Neither under FIX nor PULSE W mode, RTS doesn’t
work if Electronic shutter speed SW is set in OFF
position.
(a)Non-reset mode (Under internal sync / external sync --- Consecutive VD IN)
Exposure starts at the timing of TRIG signal IN. After each exposure is completed, the
camera outputs video at each next VD IN timing.
□1/60s Non-interlace
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
INT/EXT VD
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
VIDEO OUT
Definite
Outputs VD,V-SYNC
during standby
Outputs video at the next VD
timing after exposure
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
□1/120s 2:1 Interlace
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
INT/EXT VD
EVEN
ODD
EVEN
ODD
EVEN
ODD
EVEN
ODD
EVEN
ODD
EVEN
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
EVEN
image
ODD
image
ODD
image
EVEN
image
VIDEO OUT
EVEN
ODD
EVEN
ODD
EVEN
ODD
EVEN
ODD
EVEN
ODD
EVEN
Definite
Outputs VD,V-SYNC
during standby
Outputs video at the next VD
timing after exposure
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
8
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(b) Non-reset mode (Under external sync --- Single VD IN)
After TRIG IN and exposure, the camera goes into standby until next ext. VD IN.
□1/60s Non-interlace
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
EXT VD
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
VIDEO OUT
Definite
In sync with ext.VD during standby
Outputs video at the next VD
timing after exposure
(No video output)
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
*Don’t provide ext. VD IN during exposure.
** After automatic return, fix ext. VD IN at Hi.
□1/120s 2:1 Interlace
Video output field (ODD/EVEN) is determined by ext. VD falling edge and ext. HD
phase.
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
ODD
phase
EVEN
phase
ODD
phase
EXT VD
ODD
EVEN
EVEN
ODD
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
ODD
image
EVEN
image
VIDEO OUT
ODD
ODD
EVEN
ODD
EVEN
ODD
EVEN
Definite
In sync with ext.VD during standby
(No video output)
Outputs video at the next VD
timing after exposure
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
*Don’t provide ext. VD IN during exposure.
** After automatic return, fix ext. VD IN at Hi.
9
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(c)V-reset mode (Under internal sync / external sync --- No VD IN)
Exposure starts at the timing of TRIG signal IN. After each exposure is completed, the
camera outputs video immediately by resetting VD. (HD is not reset)
□1/60s Non-interlace
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
VIDEO OUT
Definite
VD,V-SYNC pause during standby
VD,V-SYNC output for 1V only
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
□1/120s 2:1 Interlace
Irrespective of TRIG IN phase, the camera always outputs ODD field image.
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
ODD
image
EVEN
image
ODD
image
ODD
image
VIDEO OUT
ODD
EVEN
ODD
VD,V-SYNC output for 1V only
ODD
Definite
VD,V-SYNC pause during standby
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
(d) SYNC reset mode (Under internal sync)
Exposure starts at TRIG signal input timing, resets HD, and outputs video immediately
after exposure by resetting VD.
* Available under FIX mode only.
□1/60s Non-interlace
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
CCD Exposure
Exposure time
(E-shutter speed)
VIDEO OUT
Definite
VD,V-SYNC pause during standby
VD,V-SYNC output for 1V only
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
10
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
□1/120s 2:1 Interlace
Irrespective of TRIG IN phase, the camera always outputs ODD field image.
Automatically returns to normal shutter
if fixed H level (after approx. 1/6s)
TRIG IN not acceptable for
1V after mode chenge
TRIG IN
(Positive)
CCD Exposure
Exposure time
(E-shutter speed)
ODD
image
EVEN
image
ODD
image
ODD
image
VIDEO OUT
ODD
EVEN
ODD
VD,V-SYNC output for 1V only
ODD
Definite
VD,V-SYNC pause during standby
WEN OUT
(Standard)
WEN OUT
[Option]
Normal shutter
Random trigger shutter
Normal shutter
(4-3) MULTIPLE SHUTTER mode
Multiple shutter operation is available by providing TRIG IN more than one time before
ext. VD IN. (Non-reset mode, single VD, consecutive VD IN)
□1/60s Non-interlace
TRIG IN
(Positive)
EXT VD
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
VIDEO OUT
Three exposures are mixed and output
here
WEN OUT
(Standard)
WEN OUT
[Option]
□1/120s 2:1 Interlace
Video output field (ODD/EVEN) is determined by ext. VD falling edge and ext. HD
phase.
TRIG IN
(Positive)
ODD
phase
EVEN
phase
EXT VD
CCD Exposure
Exposure time
(E-shutter speed or
pulse width)
ODD
image
EVEN
image
VIDEO OUT
Three exposures are mixed and output here
WEN OUT
(Standard)
WEN OUT
[Option]
11
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
„ RTS TRIG IN notes
1/60s Non-interlace
9H
INT VD
INT HD
OB
1
2
3
4
5
490 492 494
OB
VIDEO OUT
WEN OUT
(Standard)
Video output time
TRIG invalid period
1/120s Interlace ODD Field
9H
INT VD
INT HD
8
9
12 16
13 17
484 488 492
485 489 493
OB
OB 2
4
5
6
7
1
3
OB
VIDEO OUT
WEN OUT
(Standard)
TRIG invalid period
Video output time
1/120s Interlace EVEN Field
9H
INT VD
INT HD
7
8
11 15
12 16
483 487 491
484 488 492
OB
1
2
3
4
5
6
OB
VIDEO OUT
WEN OUT
(Standard)
TRIG invalid period
Video output time
* TRIG becomes invalid even if TRIG (exposure start) is inputted during
TRIG invalid period.
* An image may be affected if TRIG (exposure start) is inputted during
the video output time.
* An imege may not be outputted normally if exposure is terminated during
the video output time.
„ Exposure time delay under RTS
When the RTS is active, both in FIX mode and PULSE W mode, there is a time delay of
approximately 1.4 micro s until the start of exposure after the rising edge of TRIG signal
(positive).
„ Exposure time under pulse width mode
Under RTS pulse mode, the exposure time is determined by the pulse width. More exactly,
the actual time is the pulse width plus approximately 8.0 micro s.
TRIG IN
Pulse width
CCD
Exposure
Exposure delay time = Approximately 1.4 micro s
Exposure time = Pulse width + Approx. 8.0 micro s
12
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(5-4) Restart / Reset
The restart / reset function is available with the ext.VD signal. You can get an arbitrary
slower shutter speed than normal shutter and random trigger shutter.
Here are some notes;
*
The shutter speed (exposure time) is determined by ext. VD signal interval.
** This function is enabled when the rear-panel shutter speed DIP SW is OFF.
*** Supply consecutive HD.
□1/60s Non-interlace
EXT VD IN
CCD Exposure
VIDEO OUT
The exposure time is
determined by VD interval
WEN OUT
(Standard)
WEN OUT
[Option]
□1/120s 2:1 Interlace
Video output field (ODD/EVEN) is determined by ext. VD falling edge and ext. HD
phase.
ODD
phase
EVEN
phase
EXT VD IN
CCD Exposure
ODD
image
EVEN
image
VIDEO OUT
ODD
EVEN
The exposure time is
determined by VD interval
WEN OUT
(Standard)
WEN OUT
[Option]
13
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(5)Partial-scan mode selection (Camera rear-panel DIP SW)
Switches partial-scan mode
Note: Sometimes phenomenon called as “whiteout” occurs at the top of the screen when
there is strong incident light entering in the wide area of a CCD, however, this is not
a malfunction. If this occurs, reduce the amount of incoming rays.
(5-1)1/2 Partial-scan (Rear-panel SW: #8-OFF, #9-ON) --- Screen center 1/2 readout
□1/60s Non-interlace
Under 1/60s non-interlace mode, only the center portion of 227H out of the total
effective lines 494H (excluding BLK time) is read out. Available both under external /
internal mode.
High-speed
transfer
Normal-
speed
130H
227H
transfer
Normal-
speed
transfer
227H
137H
High-speed
transfer
■Under normal shutter (Electronic shutter OFF)
Notes: * Under ext. sync, the ext. VD should be 1V = 262H.
** Under normal shutter, set the rear-panel DIP SW #6, #7 in OFF.
131
357
131
357
<V-reset>
VIDEO OUT
14H
227H
21H
V BLK
(Include
High-speed
transfer)
VIDEO output
time
High-
speed
transfer
262H
262H
WEN OUT
(Standard)
3H
3H
3H
3H
3H
3H
WEN OUT
[Option]
■Under other shutter modes
131
357
<Non-reset>
VIDEO OUT
14H (263H)
227H
21H
V BLK
(Include
High-speed
VIDEO output
time
*1
High-
speed
transfer
transfer)
WEN OUT
(Standard)
3H
3H
WEN OUT
[Option]
*2
4H
*1:Arbitrary under ext.sync
*2:See "7.TIMING CHART (4)WEN timing".
14
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
□1/120s 2:1 Interlace
Under 1/120s interlace mode, only the center portion of 207H out of the total effective
lines 485H (excluding BLK time) is read out. Available both under external / internal
mode.
ODD Field
High-speed
trasfer
73H
103H
66.5H
Normal-
speed
transfer
103H
Normal-
speed
transfer
High-speed
transfer
EVEN Field
High-speed
transfer
72.5H
104H
66H
Normal-
speed
transfer
104H
Normal-
speed
transfer
High-speed
transfer
■Under normal shutter (Electronic shutter OFF)
Notes: * Under ext. sync, the ext. VD should be 1V = 131.5H.
** Under normal shutter, set the rear-panel DIP SW #6, #7 in OFF.
<V-reset>
ODD image
EVEN image 359
154
155
358
359
153
154
360
VIDEO OUT
7H
7H
103H
104H
21H
20.5H
High-
speed
transfer
High-
speed
transfer
VIDEO output
time
VIDEO output
time
V BLK
(Include
High-speed
transfer)
V BLK
(Include
High-speed
transfer)
0.5H
131.5H
131.5H
WEN OUT
(Standard)
9H
9H
8.5H
8.5H
9H
9H
WEN OUT
[Option]
15
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
■Under other shutter modes
<Non-reset>
ODD image
154
155
358
359
VIDEO OUT
7H (131.5H)
103H
21H
V BLK
(Include
High-speed
transfer)
VIDEO output
time
*1
High-
speed
transfer
WEN OUT
(Standard)
9H
8.5H
WEN OUT
[Option]
10H
*2
EVEN image
153
154
359
360
VIDEO OUT
7H (132H)
104H
20.5H
V BLK
(Include
High-speed
transfer)
VIDEO output
time
*1
High-
speed
WEN OUT
(Standard)
transfer
8.5H
9H
WEN OUT
[Option]
9.5H
*2
*1:Arbitrary under ext.sync
*2:See "7.TIMING CHART (4)WEN timing".
16
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(5-2)1/4 Partial-scan (Rear-panel SW: #8-ON, #9-ON) --- Screen center 1/4 readout
□1/60s Non-interlace
Under 1/60s non-interlace mode, only the center portion of 81H out of the total effective
lines 494H (excluding BLK time) is read out. Available both under external / internal
mode.
Normal-
speed
81H
High-speed
transfer
200H
transfer
Normal-
speed
81H
transfer
High-speed
transfer
213H
■Under normal shutter (Electronic shutter OFF)
Notes: * Under ext. sync, the ext. VD should be 1V = 131H.
** Under normal shutter, set the rear-panel DIP SW #6, #7 in OFF.
201
281
201
281
<V reset>
VIDEO OUT
22H
81H
Video output
time
28H
V BLK
(Include
High-speed
transfer)
High
-speed
transfer
131H
131H
WEN OUT
(Standard)
3H
3H
3H
3H
3H
3H
WEN OUT
[Option]
■Under other shutter modes
201
281
<Non-reset>
VIDEO OUT
22H (394H)
81H
28H
V BLK
Video output
time
*1
High
(Include
High-speed
transfer)
-speed
transfer
WEN OUT
(Standard)
3H
3H
WEN OUT
[Option]
4H
*2
*1:Arbitrary under ext.sync
*2:See "7.TIMING CHART (4)WEN timing".
17
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
□1/120s 2:1 Interlace
Under 1/120s interlace mode, only the center portion of 61H out of the total effective
lines 485H (excluding BLK time) is read out. Available both under external / internal
mode.
ODD Field
Normal-
speed
transfer
High-speed
transfer
103H
30H
30H
Normal-
speed
transfer
High-speed
transfer
109.5H
EVEN Field
High-speed
transfer
Normal-
speed
transfer
102.5H
31H
31H
Normal-
speed
transfer
High-speed
transfer
109H
■Under normal shutter (Electronic shutter OFF)
Notes: * Under ext. sync, the ext. VD should be 1V = 65.5H.
** Under normal shutter, set the rear-panel DIP SW #6, #7 in OFF.
<V reset>
ODD image
EVEN image
214
215
272
273
213
214
273
274
VIDEO OUT
11H
11H
30H
31H
24H
23.5H
Video output
time
Video output
time
V BLK
(Include
High-speed
transfer)
V BLK
(Include
High-speed
transfer)
High
-speed
transfer
High
-speed
transfer
65.5H
65.5H
0.5H
WEN OUT
(Standard)
9H
9H
9H
9H
8.5H
8.5H
WEN OUT
[Option]
18
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
■Under other shutter modes
<Non-reset>
ODD image
214
215
272
273
VIDEO OUT
11H (197.5H)
30H
24H
V BLK
(Include High-
speed
Video output
time
*1
High
-speed
transfer
transfer)
WEN OUT
(Standard)
9H
8.5H
WEN OUT
[Option]
10H
*2
EVEN image
213
214
273
274
VIDEO OUT
11H (197H)
31H
23.5H
V BLK
(Include High-
speed
*1
Video output
time
High
-speed
transfer
transfer)
WEN OUT
(Standard)
8.5H
9.5H
9H
WEN OUT
[Option]
*2
*1:Arbitrary under ext.sync
*2:See "7.TIMING CHART (4)WEN timing".
19
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(5-3) Programmable partial [Option]
By designating the high-speed transfer portion with external PARTIAL signal input, the
camera read out only the portion of CCD area necessary for your application. This is
available under ext. sync.
EXT VD
EXT HD
1(H)
10 Line
2(H)
PARTIAL PULSE
VIDEO OUT
a(H)
[ *1 ]
n(H) Total line = n(H) x 10 line
Start
Finish
High-speed trans. n(H)
BLK trans. 2(H) Normal-speed
1/120s Interlace
1/60s non-interlace
6.0
[*1]
a(H)
1st field
12.0
2nd field
11.5
(Conditions)
z The starting point of external partial signal is [*1] from the falling edge of ext. VD.
z The external partial signal is controlled at each ext. HD falling edge. Set the start / finish of
the external partial signal in 1H increments.
z The number of 1H high-speed transfer line is 10 lines. The actual lines are determined by
the external partial signal “hi” period. (Minimum: 2H = 20 lines)
z Set video output time more than 30H. And high-speed transfer time (the external partial
signal “hi” period) before video output time is is as follows;
from 2H through 22H under 1/60s non-interlace mode
from 2H through 11H under 1/120s interlace mode
z After high-speed transfer, 2H is allocated to blank transfer period. Normal transfer starts at
the next line.
z VIDEO OUT vertical blanking is;
V. blanking = [*1](H) + n(H) + BLK transfer [2(H)] – 1H
Example follows below.
(High-speed 2H = 20 lines (minimum), Normal-speed 70 lines + BLK 2H)
Note: Items shown as [Option] in this document is not included in your purchase as
standard components. Contact our dealer / distributor for details.
20
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
□1/60s Non-interlace
High-speed
transfer
10H
68H
Normal-
speed
transfer
68H
Normal-
speed
transfer
High-speed
transfer
416H
The timing is as follows;
EXT.VD
1H
494
1
VIDEO OUT
(Normal scan)
20H
494H
V BLK
WEN OUT
(Standard)
3H
70H
*2
2H
Partial Pulse
6H
11
78
VIDEO OUT
(Partial scan)
9H
68H
VIDEO OUT
(448H)
*1
V BLK
WEN OUT
(Standard)
3H
WEN OUT
(Normal shutter mode)
[Option]
WEN OUT
(Other shutter mode)
[Option]
*3
*1:Arbitrary under ext.sync.
*2:Partial over actual line is OK.
4H
*3:See "7.TIMING CHART (4)WEN Timing".
21
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
□1/120s 2:1 Interlace, ODD field
High-speed
transfer
13H
Normal-
speed
transfer
68H
Normal-
speed
68H
transfer
High-speed
transfer
161.5H
The timing is as follows;
ODD Feild
EXT.VD
1H
8
9
492
493
VIDEO OUT
(Normal scan)
20H
242.5H
V BLK
WEN OUT
(Standard)
9H
*2
70H
2H
Partial Pulse
12H
34
35
168
169
VIDEO OUT
(Partil scan)
15H
68H
VIDEO OUT
(179.5H)
*1
V BLK
WEN OUT
(Standard)
9H
WEN OUT
(Normal shutter mode)
[Option]
WEN OUT
(Other shutter mode)
[Option]
*3
10H
*1:Arbitrary under ext.sync.
*2:Partial over actual line is OK.
*3:See "7.TIMING CHART (4)WEN Timing" .
22
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
□1/120s 2:1 Interlace, EVEN field
High-speed
transfer
12.5H
Normal-
speed
transfer
68H
Normal-
speed
68H
transfer
High-speed
transfer
162H
The timing is as follows;
EVEN Feild
EXT.VD
1H
7
8
491
492
VIDEO OUT
(Normal scan)
20H
242.5H
V BLK
WEN OUT
(Standard)
8.5H
*2
70H
2H
Partial Pulse
11.5H
33
34
167
168
VIDEO OUT
(Partial scan)
14.5H
V BLK
68H
VIDEO OUT
(180H)
*1
WEN OUT
(Standard)
8.5H
WEN OUT
(Normal shutter mode)
[Option]
WEN OUT
(Other shutter mode)
[Option]
*3
9.5H
*1:Arbitrary under ext.sync.
*2:Partial over actual line is OK.
*3:See "7.TIMING CHART (4)WEN Timing".
Note: Items shown as [Option] in this document is not included in your purchase as
standard components. Contact our dealer / distributor for details.
23
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
6. SPECIFICATIONS
[Basic spec]
(1) Image sensor
Total pixels
All Pixel’s Data Read-out Interline CCD
692(H) x 504(V)
Active pixel
659(H) x 494(V)
Video output pixels
Scanning area
Unit cell size
648(H) x 494(V) (Under non-interlace)
4.88(H) x 3.66(V) mm (=Equivalent to 1/3 type CCD size)
7.4(H) x 7.4(V) micro m (Square-grid array)
Special format (Non-conforming to EIA)
525 lines
(2) TV system
(3) Scanning lines
(4) Interlace
1/60s Non-interlace mode
1/120s 2:1 Interlace mode
Switching via rear-panel DIP SW
Internal/External automatic switch-over
4:3
(5) Sync system
(6) Aspect ratio
(7) Video output
(8) Resolution
VS 1.0V(p-p) / 75Ω, DC coupled, 1 line (AC as [Option])
485 TV lines(H)
485 lines (350 TV lines)(V)
(9) S/N
Standard: 52dB(p-p)/rms (Initial factory setting)
Standard 400 lx (F5.6)
(10) Illumination
Minimum 4 lx (F1.4) (GAIN MAX, Approx. 50% video output)
FIX (Fixed) gain: Factory-shipped preset level
MANU (Manual) gain: Setting through GAIN VR
FIX / MANU switching via rear-panel DIP SW
Gamma = 1 (Fixed)
(11) Gain
(12) Gamma correction
(13) White-clip level
(14) Power source
Approx. 840mV(p-p) (Excluding SYNC)
DC12V ±10%
Ripple voltage: 50mV(p-p) or less
Approx. 1.5W
(15) Power consumption
[Internal sync spec]
(1) Base clock frequency
(2) H sync frequency
(3) V sync frequency
24.545MHz (1CLK) ±200ppm
31.468kHz (1H = 780CLK)
59.94Hz (Under non-interlace)
119.88Hz (Under 2:1 interlace)
Note: Items shown as [Option] in this document is not included in your purchase as standard
components. Contact our dealer / distributor for details.
24
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
[External sync spec]
(1) Ext. sync input signal
(2) Input impedance
HD/VD
75-ohm / High impedance 10k-ohm (switching via rear-panel SW)
(Initial factory setting: High)
(3) Input level
From 2 through 5V (p-p) under high impedance input
From 2 through 4V (p-p) under 75-ohm input
1/60s non-interlace or 1/120s 2:1 interlace
Negative
(4) Interlace
(5) Polarity
(6) Pulse width
HD: 3.2 +/- 1 micro s (LOW)
VD: From 125 through 400 micro s (LOW)
fH = 31.468kHz +/- 1%
(7) Repeating frequency
(8) Phase difference
fV = fH/262.5 or fH/525
HD/VD: 0 +/- 5.0 micro s, 1/fH/2 +/- 5.0 micro s
[Shutter trigger spec]
Exposure-starting-cue signal in random trigger shutter mode
LOW level: From 0 through 0.5V(p-p)
HIGH level: From 4 through 5V(p-p)
High impedance (10k-ohm)
(1) Input level
(2) Input impedance
(3) Capture timing
Rising edge detection (Positive)
(Falling edge detection (Negative) as [Option])
Minimum 2 micro s
(4) Pulse width
Maximum 1/8s
[Sync signal spec]
(1) Readout signal
(2) Polarity
WEN readout timing pulse
Negative (Positive under VIDEO output mode [Option])
1H output (Available under VIDEO output mode [Option])
(3) Pulse width
VIDEO OUT
WEN OUT
（1H）
NEGA
POSI
WEN OUT
(VIDEO output)
[Option]
(4) Output circuit
* Set WEN termination to be high impedance.
5V
WEN
WEN OUT
100
50
Note: Items shown as [Option] in this document is not included in your purchase as standard
components. Contact our dealer / distributor for details.
25
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
[Electronic shutter spec]
(1)Normal shutter
Shutter-speed setting via rear-panel SW (Initial: OFF)
8 steps switch-able (= OFF, 1/200s, 1/500s, 1/1000s, 1/2000s, 1/4000s,
1/8000s, 1/20000s)
(2)RTS
(a)Operation mode
No.
1
Reset
Exposure
Sync
Internal
Rear SW
2
3
Consecutive HD / Consecutive VD IN
Consecutive HD / Single VD IN
Internal
(FIX mode)
Non-reset
4
TRIG pulse width
5
Consecutive HD / Consecutive VD IN
Consecutive HD / Single VD IN
Internal
(PULSE width mode)
6
7
V-reset
SYNC reset
V reset
Rear SW
8
Consecutive HD IN
Internal
(FIX mode)
9
10
11
Internal
TRIG pulse width
(PULSE width mode)
Consecutive HD IN
Notes : * RTS mode automatically switches over through TRIG IN
**RTS disabled under Electronic shutter OFF
(b)Multiple shutter
(3)Restart / Reset
Multiple shutter via ext. trigger signal and ext. VD signal
Notes : * Operation like No.3, 6 above
Restart / reset available via ext. VD signal
(Switching via rear panel DIP SW, Initial OFF)
Notes : * The exposure-time (shutter-speed) is determined by ext.
VD interval.
** Enabled when rear-panel DIP SW OFF.
***Provide Consecutive HD.
[Partial scan]
(1)Operation mode
No
1
2
3
4
5
6
7
8
Scan mode
Sync
Reset
E-shutter Normal
E-shutter RTS
Enabled
Non-reset Enabled
V-reset Disabled
Non-reset Enabled
V-reset Disabled
Non-reset Enabled
V-reset Disabled
Non-reset Enabled
V-reset Disabled
Non-reset Enabled
[Option]
[Option]
[Option]
[Option]
[Option]
Internal
1/2 partial
Consecutive HD VD IN
Consecutive HD (VD) IN
Enabled
Enabled
Enabled
Enabled
Internal
1/4 partial
Consecutive HD VD IN
Consecutive HD (VD) IN
9
Programmable Consecutive HD VD IN
[Option]
Note: Items shown as [Option] in this document is not included in your purchase as
standard components. Contact our dealer / distributor for details.
26
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) Reset mode
As shown in (1) above, non-reset and V-reset is available.
([Option]: Doesn’t come as standard. Contact our dealer / distributor for details)
(a) non-reset (Electronic shutter enabled)
VD doesn’t get reset after video readout. The interval of VD signal is as follows.
1/2 partial scan 1/4 partial scan
1/60s non-interlace
1/120s interlace
525H
262.5H
525H
262.5H
Partial A
Partial B
Partial C
VIDEO OUT
VD Interval
*Note: Under normal shutter mode, when non-reset is selected on partial scan,
electronic shutter is valid.
Please note that the exposure time is shortened than the setting value
when the external VD is input at shorter than the above VD interval.
(b) V-reset (Electronic shutter disabled)
VD does get reset after video readout. Under internal sync, the interval of VD signal is as
follows.
1/2 partial scan 1/4 partial scan
1/60s non-interlace
1/120s interlace
262H
131.5H
131H
65.5H
Partial A
Partial B
Partial C
Partial D
Partial E
VIDEO OUT
VD interval
(3) Partial signal [Option]
Programmable mode input signal
(a) Input level
LOW level: From 0 through 0.5V
HIGH level: From 4 through 5V
High impedance (10kΩ)
(b) Input impedance
(c) Polarity
Positive (Hi: High-speed transfer)
Note: Items shown as [Option] in this document is not included in your purchase as standard
components. Contact our dealer / distributor for details.
27
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
[Mechanical spec]
(1) External dimension
29 x 29 x 39.5(D) mm (Not including protrusion)
Refer to the attached external view drawing
Approximately 42g
(2) Weight
(3) Lens mount
(4) GND / insulation
C mount
Circuit GND - Chassis electrically conducted
[Ambient condition]
(1)Environment condition
Performance guaranteed Temperature: From 0 through 40 °C
Humidity: From 30 through 90 % (No condensing)
Temperature: From -5 through 45 °C
Operation guaranteed
Storage
Humidity: From 10 through 90 % (No condensing)
Temperature: From -20 through 60 °C
Humidity: From 10 through 90 % (No condensing)
(2)EMC conditions (Electro-Magnetic Compatibility)
EMI (Electro-Magnetic Interference)
EN61000-6-4 Conformity
EMS (Electro-Magnetic Susceptibility)
EN61000-6-2 Conformity
*Conformity of EMC conditions
About the conformity of the EMC standard of this machines, it has guaranteed in the
conditions combined with the option part of 4th clause.
When used combining parts other than specification of our company, I ask you to have
final EMC conformity checked of a visitor with a machine and the whole equipment.
28
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
[Connector pin assignment]
(1) Compatible connector
(2) Pin assignment
HR10A-10P-12S (Supplied by HIROSE ELEC.)
Connector pin layout
①
⑨
⑫
②
⑧
⑩
⑤
⑪
⑦
③
④
⑥
Picture Rear-panel camera connector
(Rear-view)
12 pin male
Pin
No.
1
Signal
(Standard)
DC12V GND
DC12V
Signal
[Option]
2
3
4
5
6
VIDEO GND
VIDEO OUT
HD GND
HD IN
7
VD IN
8
9
10
11
12
TRIG GND
NC
WEN OUT
TRIG IN
VD GND
NC
TRIG IN
GND
DC12V
PARTIAL
NC
Notes : *Before connecting / disconnecting the connector, make sure the camera power is OFF.
**For board connection, check compatibility.
Note: Items shown as [Option] in this document is not included in your purchase as standard
components. Contact our dealer / distributor for details.
29
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
[Switch setting]
(1) CCU rear-panel DIP SW
No.
Function
OFF
ON
Manual GAIN
adjustable
via GAIN
GAIN
SHUT
O
N
1
2
3
4
5
6
7
8
9
0
GAIN selection
(GAIN)
Factory-set
GAIN
1
2
3
4
E-shutter-speed
(SHUT)
See shutter-speed table (Table 1)
1/60s non-interlace 1/120s interlace
VIDEO
SMODE
Video output
mode (VIDEO)
Shutter mode
(SMODE)
Partial scan
(PART)
RTS Exposure
(EXP)
5
6
7
8
9
See shutter-mode table (Table 3)
See partial-scan table (Table 2)
PART
EXP
0
FIX mode
PULSE W mode
Notes: *
Initial factory setting: All OFF
(Table 1) Electronic shutter-speed
(Table 2) Partial-scan
Shutter-speed No.2 No.3 No.4
Partial scan No.8 No.9
OFF
1/200s
1/500s
1/1,000s
1/2,000s
1/4,000s
1/8,000s
1/20,000s
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF OFF
Not acceptable ON OFF
1/2 partial
1/4 partial
OFF ON
ON ON
ON
OFF
OFF
ON
ON
Notes : *Don’t set Electronic shutter-speed in OFF under RTS mode.
(Table 3) Shutter-mode
Shutter mode
SYNC
No.6 No.7
OFF OFF
ON OFF
OFF ON
ON ON
V reset
SYNC reset
Non-reset
Random
trigger
Internal sync
Not acceptable
Non-reset
(Multiple shutter)
Non-reset
OFF OFF
Single VD
Random
trigger
Ext. sync
HD IN
ON OFF Consecutive VD
OFF ON
ON ON
V reset
Restart / Reset
No VD
Single VD
Notes : * Under normal shutter mode partial-scan, set No.6,7 in OFF.
**Under PULSE W mode, SYNC reset is disabled.
(2)CCU rear-panel SW
Function
SW
HIGH
75Ω
Selected Function
Ext. SYNC IN impedance
(HD/VD)
HIGH impedance (Initial factory setting)
75Ω
30
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
[Relative Spectrum Response]
*Including lens characteristics, Excluding light source characteristics
[Optical black characteristics]
2
494
8
Effective
Image Area
504
V
659
692
31
2
H
Device structure
Total pixels : 692(H) x 504(V)
Effective pixels : 659(H) x 494(V)
Optical black
Horizontal : 2pixels --- 31pixels
Vertical : 8pixels --- 2pixels
31
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
7. TIMING CHART
(1)H rate timing
32
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) 1/60s Non-interlace mode
EXT VD IN
1H delay
9H
INT VD
INT HD
1
2
3
492 493 494
VIDEO
OUT
OB OB OB OB OB OB OB OB
OB OB
V.Blanking
20H
1H
1H
WEN OUT
(Standard)
Ext. VD – Ext. HD phase difference
EXT VD IN
EXT HD IN
TP2
TP1
INT VD
TP1 : 10.0 us
TP2 : 5.0 us
33
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) 1/120s 2:1 Interlace mode
ODD (1st field)
EXT VD IN
1H delay
9H
INT VD
INT HD
487 489491
488 490492
8
9
10 12 14 16 18 20 22 24 26 28 30 32 34 36
11 13 15 17 19 21 23 25 27 29 31 33 35 37
493 OB
494 OB
OB OB OB OB
2
3
4
5
6
7
OB
OB OB OB
1
VIDEO OUT
V. Blanking
20H
1H
WEN OUT
(Standard)
EVEN (2nd field)
EXT VD IN
1H delay
9H
INT VD
INT HD
486 488 490 492
487 489 491 493
7
8
9
11 13 15 17 19 21 23 25 27 29 31 33 35
10 12 14 16 18 20 22 24 26 28 30 32 34 36
494
OB
OB OB OB OB
OB OB OB OB
1
2
3
4
5
6
OB
VIDEO OUT
V. Blanking
20H
1H
WEN OUT
(Standard)
Ext. VD – Ext. HD phase difference
EXT VD IN (1)
(2)
EXT HD IN
TP3
TP3
TP1
INT VD
INT VD
(1) ODD
(2) EVEN
TP2
TP1 : ODD reset range
TP2 : EVEN reset range
TP3 : 5.0 us
10.0 us
10.0 us
34
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) WEN timing
(a)Normal shutter mode
<1/60s Non interlace mode>
Under normal scan mode
9H
INT VD
494
1
2
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
4H
521H
3H
Under partial scan V-reset mode (Standard)
9H
High-speed
transfer
INT VD
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
4H
3H
*
* 1/2 partial scan : 258H
1/4 partial scan : 127H
Under partial scan Non-reset mode [Option]
9H
High-speed
transfer
INT VD
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
4H
521H
3H
35
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
<1/120s Interlace mode ODD Field>
Under normal scan mode
9H
8
9
INT VD
492
493
OB
VIDEO OUT
(Normal scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
10H
252.5H
8.5H
Under partial scan V-reset mode (Standard)
9H
High-speed
transfer
INT VD
494
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
10H
WEN OUT
(Standard)
1H
WEN OUT
[Option]
8.5H
*
* 1/2 partial scan : 121.5H
1/4 partial scan : 55.5H
Under partial scan Non-reset mode [Option]
9H
High-speed
transfer
INT VD
494
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
10H
V.Blanking
8.5H
WEN OUT
(Standard)
1H
WEN OUT
[Option]
252.5H
<1/120s Interlace mode EVEN Field>
Under normal scan mode
9H
7
8
INT VD
491
492
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
9.5H
253H
9H
Under partial scan V-reset mode (Standard)
9H
High-speed
transfer
INT VD
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
9.5H
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
9H
*
* 1/2 partial scan : 122H
1/4 partial scan : 56H
Under partial scan Non-reset mode [Option]
9H
High-speed
transfer
INT VD
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
9.5H
V.Blanking
9H
WEN OUT
(Standard)
1H
WEN OUT
[Option]
253H
36
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(b)RTS
Non-reset mode (Consecutive VD)
<1/60s Non interlace mode>
Under normal scan mode
9H
INT VD
494
1
2
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
1H
WEN OUT
(Standard)
WEN OUT
[Option]
521H
3H
4H
Under partial scan mode
9H
High-speed
transfer
INT VD
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
521H
3H
4H
<1/120s Interlace mode ODD Field>
Under normal scan mode
9H
8
9
INT VD
492
493
OB
VIDEO OUT
(Normal scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
252.5H
8.5H
10H
Under partial scan mode
9H
High-speed
transfer
INT VD
494
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
252.5H
8.5H
10H
<1/120s Interlace mode EVEN Field>
Under normal scan mode
9H
7
8
INT VD
491
492
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
253H
9H
9.5H
Under partial scan mode
9H
High-speed
transfer
INT VD
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
253H
9H
9.5H
37
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(c)RTS
Non-reset mode (Single VD) / V-reset mode / SYNC-reset mode
<1/60s Non interlace mode>
Under normal scan mode
9H
INT VD
494
1
2
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
521H
3H
4H
Under partial scan mode
9H
High-speed
transfer
INT VD
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
3H
*
4H
* 1/2 partial scan : 258H
1/4 partial scan : 127H
Programable partial scan : Arbitrary [Option]
<1/120s Interlace mode ODD Field>
Under normal scan mode
9H
8
9
492
493
INT VD
OB
VIDEO OUT
(Normal scan)
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
252.5H
8.5H
10H
Under partial scan mode
9H
High-speed
INT VD
transfer
494
OB OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
8.5H
*
10H
* 1/2 partial scan : 121.5H
1/4 partial scan : 55.5H
Programable partial scan : Arbitrary [Option]
<1/120s Interlace mode EVEN Field>
*Under Non-reset mode (Single VD) only.
Under normal scan mode
9H
7
8
INT VD
491
492
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
253H
9H
9.5H
Under partial scan mode
9H
High-speed
transfer
INT VD
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
9H
*
9.5H
* 1/2 partial scan : 122H
1/4 partial scan : 56H
Programable partial scan : Arbitrary [Option]
38
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
(d)Restart / reset mode
<1/60s Non interlace mode>
Under normal scan mode
9H
INT VD
494
1
2
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
521H
3H
4H
Under partial scan mode
9H
High-speed
transfer
INT VD
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
521H
3H
4H
<1/120s Interlace mode ODD Field>
Under normal scan mode
9H
8
9
492
493
INT VD
OB
VIDEO OUT
(Normal scan)
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
252.5H
8.5H
10H
Under partial scan mode
9H
High-speed
transfer
INT VD
494
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
252.5H
8.5H
10H
<1/120s Interlace mode EVEN Field>
Under normal scan mode
9H
7
8
INT VD
491
492
OB
OB
VIDEO OUT
(Normal scan)
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
253H
9H
9.5H
Under partial scan mode
9H
High-speed
transfer
INT VD
OB
OB
VIDEO OUT
(Partial scan)
V.Blanking
V.Blanking
WEN OUT
(Standard)
1H
WEN OUT
[Option]
253H
9H
9.5H
39
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
8. EXTERNAL-VIEW DRAWING
40
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
Head Office: 7-1, 4 chome, Asahigaoka, Hino-shi, Tokyo, 191-0065, Japan
(Overseas Sales Department)
Phone: +81-42-589-8771 Fax: +81-42-589-8774
The design and specification is subject to change without notice.
41
D4130891A
Download from Www.Somanuals.com. All Manuals Search And Download.
|