| TL-WA890EA   N600 Universal Dual Band WiFi   Entertainment Adapter with 4 Ports   REV.:1.0.0   1910010832   Download from Www.Somanuals.com. All Manuals Search And Download.   FCC STATEMENT   This equipment has been tested and found to comply with the limits for a Class B digital device,   pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection   against harmful interference in a residential installation. This equipment generates, uses and can   radiate radio frequency energy and, if not installed and used in accordance with the instructions,   may cause harmful interference to radio communications. However, there is no guarantee that   interference will not occur in a particular installation. If this equipment does cause harmful   interference to radio or television reception, which can be determined by turning the equipment off   and on, the user is encouraged to try to correct the interference by one or more of the following   measures:   • • • Reorient or relocate the receiving antenna.   Increase the separation between the equipment and receiver.   Connect the equipment into an outlet on a circuit different from that to which the receiver   is connected.   • Consult the dealer or an experienced radio/ TV technician for help.   This device complies with part 15 of the FCC Rules. Operation is subject to the following two   conditions:   1) This device may not cause harmful interference.   2) This device must accept any interference received, including interference that may cause   undesired operation.   Any changes or modifications not expressly approved by the party responsible for compliance   could void the user’s authority to operate the equipment.   Note: The manufacturer is not responsible for any radio or TV interference caused by   unauthorized modifications to this equipment. Such modifications could void the user’s authority to   operate the equipment.   FCC RF Radiation Exposure Statement:   This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled   environment. This device and its antenna must not be co-located or operating in conjunction with   any other antenna or transmitter.   “To comply with FCC RF exposure compliance requirements, this grant is applicable to only   Mobile Configurations. The antennas used for this transmitter must be installed to provide a   separation distance of at least 20 cm from all persons and must not be co-located or operating in   conjunction with any other antenna or transmitter.”   Download from Www.Somanuals.com. All Manuals Search And Download.   CE Mark Warning   This is a class B product. In a domestic environment, this product may cause radio interference, in   which case the user may be required to take adequate measures.   National Restrictions   This device is intended for home and office use in all EU countries (and other countries following   the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:   Country   Restriction   Reason/remark   General authorization required for outdoor use and   public service   Bulgaria   None   Outdoor use limited to Military Radiolocation use. Refarming of the 2.4 GHz   10 mW e.i.r.p. within band has been ongoing in recent years to allow current   the band 2454-2483.5 relaxed regulation. Full implementation planned 2012   MHz   France   If used outside of own premises, general authorization is   required   Italy   None   General authorization required for network and service   supply(not for spectrum)   Luxembourg   Norway   None   This subsection does not apply for the geographical area   Implemented   within a radius of 20 km from the centre of Ny-Ålesund   Russian Federation None   Only for indoor applications   Note: Please don’t use the product outdoors in France.   Canadian Compliance Statement   This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject   to the following two conditions:   (1) This device may not cause interference, and   (2)This device must accept any interference, including interference that may cause undesired   operation of the device.   Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le   fonctionnement est soumis aux deux conditions suivantes:   (1) cet appareil ne doit pas provoquer d’interférences et   (2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un   fonctionnement non souhaité de l’appareil.   Download from Www.Somanuals.com. All Manuals Search And Download.   Industry Canada Statement   Complies with the Canadian ICES-003 Class B specifications.   Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.   This device complies with RSS 210 of Industry Canada. This Class B device meets all the   requirements of the Canadian interference-causing equipment regulations.   Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le   matériel brouilleur du Canada.   Korea Warning Statements   당해 무선설비는 운용중 전파혼신 가능성이 있음.   NCC Notice & BSMI Notice   注意!   依據 低功率電波輻射性電機管理辦法   第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、   加大功率或變更原設計之特性或功能。   第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行;經發現有干擾現象時,應立即   停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信規定作業之無線電信。低功率射   頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。   於 5.25GHz 至 5.35GHz 區域內操作之無線設備的警告聲明   工作頻率 5.250~5.350GHz 該頻段限於室內使用。   安全諮詢及注意事項   ●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。   ●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。   ●注意防潮,請勿將水或其他液體潑灑到本產品上。    ●插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。   ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。   ●請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。   Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам   нормативних документів та вимогам, що передбачені чинними законодавчими актами   України.   Download from Www.Somanuals.com. All Manuals Search And Download.   Safety Information    When product has power button, the power button is one of the way to shut off the product;   when there is no power button, the only way to completely shut off power is to disconnect the   product or the power adapter from the power source.     Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock   and voiding the limited warranty. If you need service, please contact us.   Avoid water and wet locations.   This product can be used in the following countries:   AT   ES   LT   BG   FI   BY   FR   MT   SK   CA   GB   NL   TR   CZ   GR   NO   UA   DE   HU   PL   DK   IE   EE   IT   LV   SE   PT   RO   RU   Download from Www.Somanuals.com. All Manuals Search And Download.   TP-LINK TECHNOLOGIES CO., LTD   DECLARATION OF CONFORMITY   For the following equipment:   Product Description: N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Model No.: TL-WA890EA   Trademark: TP-LINK   We declare under our own responsibility that the above products satisfy all the technical   regulations applicable to the product within the scope of Council Directives:   Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,   Directives 2011/65/EU   The above product is in conformity with the following standards or other normative documents   ETSI EN 300 328 V1.7.1: 2006   ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.2.1:2012   EN 55022:2010   EN 55024:2010   EN 61000-3-2:2006+A1:2009+A2:2009   EN 61000-3-3:2008   EN 60950-1:2006+A11:2009+A1:2010+A12:2011   EN 62311:2008   EN 301 893   EN 302 502   The product carries the CE Mark:   Person is responsible for marking this declaration:   Yang Hongliang   Product Manager of International Business   Date of Issue: 2013   TP-LINK TECHNOLOGIES CO., LTD.   Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,   Shennan Rd, Nanshan, Shenzhen, China   Download from Www.Somanuals.com. All Manuals Search And Download.   CONTENTS   Chapter 1 Introduction........................................................................................... 2   1.1 Product Overview.............................................................................................. 2   1.2 Main Features................................................................................................... 2   1.3 Appearance....................................................................................................... 2   Chapter 2 Hardware Installation ........................................................................... 4   2.1 Before You Begin.............................................................................................. 4   2.2 Basic Requirements.......................................................................................... 4   2.3 Connecting the Device...................................................................................... 4   Chapter 3 Quick Installation Guide....................................................................... 6   Chapter 4 Configure the Device............................................................................ 9   4.1 Status................................................................................................................ 9   4.2 Quick Setup .................................................................................................... 10   4.3 WPS................................................................................................................ 10   4.4 Advanced........................................................................................................ 12   4.4.1 LAN..................................................................................................................12   4.4.2 Wireless Settings.............................................................................................14   4.4.3 Wireless Advanced..........................................................................................14   4.4.4 DHCP Settings.................................................................................................15   4.4.5 Profile...............................................................................................................17   4.5 System Tools .................................................................................................. 19   4.5.1 Firmware Upgrade...........................................................................................19   4.5.2 Factory Defaults...............................................................................................20   4.5.3 Backup & Restore............................................................................................20   4.5.4 Reboot .............................................................................................................21   4.5.5 Password.........................................................................................................22   4.5.6 System Log......................................................................................................22   Appendix A: Factory Defaults............................................................................... 24   Appendix B: Troubleshooting............................................................................... 25   Appendix C: Specifications................................................................................... 26   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Package Contents   The following items should be found in your package:        TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Ethernet Cable   USB Cable and Power Adapter   Quick Installation Guide   Resource CD for TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4   Ports, including only This User Guide.   Note:    Make sure that the package contains the above items. If any of the listed items is damaged or   missing, please contact your distributor.   Conventions   The Entertainment Adapter, the Device or TL-WA890EA mentioned in this User guide stands for   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports without any   explanations.   Parameters provided in the pictures are just references for setting up the product, which may differ   from the actual situation. You can set the parameters according to your demand.   1 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Chapter 1 Introduction   1.1 Product Overview   The N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports TL-WA890EA can bring   all of your home or office’s Internet-enabled devices into the world of wireless.   By connecting them to TL-WA890EA, the entertainment devices in your home that previously   required running Ethernet cables around furniture, through walls and doorways can now be   connected to your network wirelessly, without the risk of degrading performance. With N600 dual   band wireless speeds and four LAN ports, TL-WA890EA provides your devices with ample   bandwidth for smooth HD video and music streaming and online gaming. What’s more, the N600   Universal Dual Band WiFi Entertainment Adapter with 4 Ports TL-WA890EA is universally   compatible with all Internet-enabled devices, so if it has an Ethernet port, you can make it wireless   in a flash.   1.2 Main Features    Gives wired-only devices (such as Smart TVs, Games Consoles, Blu-ray players, etc.) access   to an existing Wi-Fi network        Dual band performance, 300Mbps wireless speed over 5GHz or 2.4GHz   Universally compatible - works with any device with an Ethernet port   Works seamlessly with all 802.11a/b/g/n devices   Easy wireless security encryption at a push of the WPS button   CD-less installation   1.3 Appearance   Figure 1-1   2 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Figure 1-2   Detail Explanation:   Item   Status   Indication   Press the button for 1 - 2 seconds to enable WPS function.   Press the button for 5 - 8 seconds to reset TL-WA890EA.   Button   WPS/RESET   When the WPS LED keeps blinking, TL-WA890EA is connecting   to the root device; then the WPS LED will be solid for 5 minutes   and then turn off, after the connection succeeds.   LED   Ports (1-4)   To connect the client(s) to TL-WA890EA with Ethernet cable(s).   The LAN LED(s) will turn on when the corresponding port(s) is   connected to a client.   LAN   LEDs (1-4)   The LAN LED(s) will keep blinking when there is data transferring.   The LAN LED(s) will turn off when the corresponding port(s) is   disconnected.   USB   Port   LED   To connect TL-WA890EA to the power adapter with an USB cable.   When the powered-on device isn’t connected or fails in connection,   the System LED will light orange.   System   When the device is connected successfully, the system LED will   light blue.   Table 1-1   3 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Chapter 2 Hardware Installation   2.1 Before You Begin      A good knowledge of the LEDs and its indication will facilitate your quick installation of the   Entertainment Adapter.   Keep the Entertainment Adapter away from any devices that might cause wireless   interference, such as cordless phones, blue tooth devices, microwave ovens, etc.   Do not place the Entertainment Adapter too far away from the main router/AP, especially   when you are trying to connect them by pressing their WPS button.   2.2 Basic Requirements    Place your Entertainment Adapter in a well-ventilated place far from direct sunlight, any   heater or heating vent.     Leave at least 2 inches (5cm) space around the device for heat dissipation.   Turn off your Entertainment Adapter and unplug the power adapter in a lighting storm to avoid   damage.    Use Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0   or above.     Operating temperature of the Entertainment Adapter should be 0℃~40℃ (32℉~104℉).   Operating humidity of the Entertainment Adapter should be 10%~90%RH (Non-condensing).   2.3 Connecting the Device   Figure 2-1 Typical connection of TL-WA890EA   Please follow the steps below to connect the devices:   1) Connect one end of the USB cable to the USB port of TL-WA890EA, and the other end to the   power adapter; then plug the power adapter to a standard wall socket.   4 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   2) Connect your entertainment device(s) or other network-enabled device with Ethernet port   (such as Blu-ray™ players, gaming consoles, DVRs, smart TVs, etc.) to TL-WA890EA with   Ethernet cable(s).   Note:    Please ensure your device(s) connected to TL-WA890EA is configured to “Obtain an IP address   automatically”.   5 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Chapter 3 Quick Installation Guide   This chapter will guide you to configure your PC to communicate with the Entertainment Adapter   and to configure and manage the TL-WA890EA N600 Universal Dual Band WiFi Entertainment   Adapter with 4 Ports easily with a Web-based utility.   With a Web-based utility, it is easy to configure and manage the TL-WA890EA N600 Universal   Dual Band WiFi Entertainment Adapter with 4 Ports. The Web-based utility can be used on any   Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla   Firefox or Apple Safari.   1. To access the configuration utility, open a web-browser and type in the domain name   http://tplinkadapter.net in the address field of the browser.   Figure 3-1 Login to the Entertainment Adapter   Name and Password (both in lower case letters). Then click OK or press Enter.   Figure 3-2 Login Windows   Note:    If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go   to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,   cancel the Using Proxy checkbox, and click OK to finish it.   2. After successful login, there will pop up the Quick Setup page. Click Next to get the quick   setup started.   6 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Figure 3-3 Quick Setup Start   Figure 3-4 Quick Setup – Choose Region and Mode   4. The device will detect the existing network. Please wait for a while.   Figure 3-5 Quick Setup – Detect Existing Network   5. A list of available wireless network will appear. Check the box before the SSID of your desired   network, and then click Next.   Figure 3-6 Quick Setup – Available Wireless Networks   7 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Password of your selected target network and then click Next to continue.   Figure 3-7 Quick Setup – Wireless Settings   Finish to complete the Quick Setup. If there is anything wrong, click Back to return the   previous pages and reconfigure it.   Figure 3-8 Quick Setup – Review Settings   8 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Chapter 4 Configure the Device   This Chapter describes how to configure your Entertainment Adapter via the web-based   management page. The TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter   with 4 Ports is easy to configure and manage with the Web-based (Internet Explorer, Firefox,   Safari, Opera, Chrome, Netscape® or Navigator) management page, which can be launched on   any windows, Macintosh or UNIX OS with a web browser.   After a successful login, you can configure and manage the device. There are five main menus on   the leftmost column of the web-based management page: Status, Quick Setup, WPS, Advanced   and System Tools. Submenus will be available after clicking one of the main menus. On the right   of the web-based management page are the detailed explanations and instructions for the   corresponding page.   4.1 Status   Selecting Status will enable you to view the Entertainment Adapter’s current status and   configuration, all of which are read-only.   Figure 4-1 Status      Firmware Version - This field displays the current firmware version of the Entertainment   Adapter.   Hardware Version - This field displays the current hardware version of the Entertainment   Adapter.   Wireless - These are the current settings or information for Wireless. You can configure them   in the Advanced -> Wireless Settings page.    Connection Status - It shows whether your device has been connected to a wireless   network currently.   9 Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports     Main Router/AP Wi-Fi Network Name - It shows the name of the wireless network your   device has connected to, also called SSID.   MAC Address of Main Router/AP - It shows the physical MAC address of the Main   Router/AP your device has connected to, also called BSSID.     Channel - The wireless channel in current use.   Signal - It shows the strength of the root wireless network signal that the device has   received.     Band - The wireless band that this device is working in.   MAC Address - The physical address of the device, as seen from the Advanced -> LAN   page.    Wired - As follows is the information of Wired LAN. You can configure them in the Advanced   -> LAN page.    MAC Address - The physical address of the device, as seen from the Advanced -> LAN   page.     IP Address - The LAN IP address of the device.   Subnet Mask - The subnet mask associated with LAN IP address.    System Up Time - The duration since the device was powered on or reset.   Click the Refresh button to get the latest status and settings of the device.   4.2 Quick Setup   4.3 WPS   WPS (Wi-Fi Protected Setup) can help you to quickly and securely connect to a network. This   section will guide you to add a new wireless device to an existing network quickly by WPS function.   The WPS function can be configured on the page as shown in Figure 4-2.   Figure 4-2 WPS    WPS Status - To enable or disable the WPS function here.   If the root device (a wireless router or an access point) supports WPS and is equipped with a WPS   button, the following 3 methods are all available. While if the root device supports WPS but doesn't   have a WPS button, only the 3rd one is available.   Method 1:   1) Push the WPS button on the root device.   10   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   2) Within 2 minutes, push the WPS button on this device.   Method 2:   1) Push the WPS button on the root device.   2) Keep the WPS Status as Enabled, choose "Push the button on my access point or wireless   router" on the WPS page, and then click Connect.   Figure 4-3   Method 3:   1) Keep the WPS Status as Enabled, choose "Enter the PIN of this device to my access point or   wireless router" on the WPS page, and get the Current PIN code of this device in Figure 4-4   11   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   (Each device has its unique PIN code, or you can generate a new one by clicking Gen New   PIN button. Here we take the default PIN code 12345670 of this device for example).   Figure 4-4   2) Enter the PIN to the main router/AP’s WPS page, and then click Connect on it.   Figure 4-5   4.4 Advanced   Settings, Wireless Advanced, DHCP Settings and Profile. Clicking any of them will enable you   to configure the corresponding function. The detailed explanations for each submenu are provided   below.   Figure 4-6 The Advanced menu   4.4.1 LAN   Selecting Advanced > LAN will enable you to configure the IP parameters of Network on this   page.   12   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Figure 4-7 LAN – Smart IP (DHCP)   ’ Figure 4-8 LAN – Static IP     MAC Address - The physical address of the LAN port, as seen from the LAN. The value   cannot be changed.   Type – Two IP types are supported: Static IP and Smart IP (DHCP), and they are explained   below.     Static IP - In this type, you can configure IP Address/Gateway manually.   Smart IP (DHCP) - In this type, if your Entertainment Adapter have connected to a router,   your client will dynamically get an IP Address/Gateway from the router, otherwise the   client will get a IP Address/Gateway in the same network as you set below. And this type   is recommended.     IP Address - Enter the IP address of your Entertainment Adapter in dotted-decimal notation   (factory default setting is 192.168.0.254).   Subnet Mask - An address code that determines the size of the network. Normally use   255.255.255.0 as the subnet mask.   Note:    1. The IP parameters cannot be configured if you have chosen Smart IP (DHCP). In this   situation the device will automatically configure the IP parameters appropriate to your need.   2. If you are not familiar with the setting items in this page, it's strongly recommended to keep   the provided default values, otherwise may result in lower wireless network performance or   even can't work.   3. If you choose Static IP, the domain name log in function won't work, and you have to use the   IP you set to log in the Entertainment Adapter's web based utility.   13   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   4.4.2 Wireless Settings   Selecting Advanced > Wireless Settings will enable you to configure the basic settings for your   wireless network on the screen below (Figure 4-9).   Figure 4-9 Wireless Settings     Main Router/AP Wi-Fi Network Name - The name of the wirless network this device is going   to connect to.   MAC Address of Main Router/AP - The physical MAC address of the Main Router/AP this   device is going to connect to.      Band - The wireless band that the root access point or wireless router is working in.   Wireless Security Type - The wireless security type of the existing wireless network.   Encryption - The encryption of the existing wireless network. It is used when the wireless   security type is WPA-PSK or WPA2-PSK.      WEP Index - The WEP index is only used when the wireless security type is WEP (ASCII) or   WEP (Hexadecimal).   WEP Auth Type - The authorization type of WEP. It is only used when the wireless security   type is WEP (ASCII) or WEP (Hexadecimal).   Wireless Password - The wireless password of the existing wireless network. If the Wireless   Security Type is WPA-PSK or WPA2-PSK, the length of this field should be between 8 and 63   characters which are case-sensitive. If the Wireless Security Type is WEP (ASCII), the length   should be 5 or 13 characters. If the Wireless Security Type is WEP (Hexadecimal), the length   should be 10 or 26 digits.   4.4.3 Wireless Advanced   Selecting Advanced > Wireless Advanced will allow you to do some advanced settings for the   device in the following screen shown in Figure 4-10.   14   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Figure 4-10 Wireless Advanced     Main Router/AP Wi-Fi Network Name - The name of the wirless network this device is going   to connect to.   MAC Address of Main Router/AP - The physical MAC address of the Main Router/AP this   device is going to connect to.      Band - The wireless band that the root access point or wireless router is working in.   Wireless Security Type - The wireless security type of the existing wireless network.   Encryption - The encryption of the existing wireless network. It is used when the wireless   security type is WPA-PSK or WPA2-PSK.      WEP Index - The WEP index is only used when the wireless security type is WEP(ASCII) or   WEP(Hexadecimal).   WEP Auth Type - The authorization type of WEP. It is only used when the wireless security   type is WEP (ASCII) or WEP (Hexadecimal).   Wireless Password - The wireless password of the existing wireless network. If the Wireless   Security Type is WPA-PSK or WPA2-PSK, the length of this field should be between 8 and 63   characters which are case-sensitive. If the Wireless Security Type is WEP (ASCII), the length   should be 5 or 13 characters. If the Wireless Security Type is WEP (Hexadecimal), the length   should be 10 or 26 digits.   4.4.4 DHCP Settings   This device is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which   provides the TCP/IP configuration for all the clients connected to this device in the LAN. The DHCP   LAN type as Static IP in Advanced ->LAN page.   Note:    The DHCP Settings function cannot be configured if you have chosen Smart IP (DHCP) in   Advanced -> LAN, in which situation the device will help you configure the DHCP automatically   as you need. The DHCP Settings page will appear as Figure 4-11.   15   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Figure 4-11 DHCP Settings – Disabled   Figure 4-12 DHCP Settings – Enabled    DHCP Server - Enable or Disable the server. If you disable the Server, you must have   another DHCP server within the LAN, or else you must configure the IP address of the clients   manually.      Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.100   is the default start IP address.   End IP Address - This field specifies the last address in the IP Address pool. 192.168.0.199   is the default end IP address.   Address Lease Time - The Address Lease Time is the length of time when a network user   will be allowed to keep connected to this device with the current DHCP Address. Enter the   amount of time (in minutes) the DHCP address will be "leased". The time range is 1~2880   minutes. The default value is 120 minutes.     Default Gateway - (Optional) It's suggested to input the IP Address of the LAN port of this   device. The default value is 192.168.0.254.   Default Domain - (Optional) Input the domain name of your network.   16   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports     Primary DNS - (Optional) Input the DNS IP address provided by your ISP. Or consult your   ISP.   Secondary DNS - (Optional) You can input the IP Address of another DNS server if your ISP   provides two DNS servers.   Click Save to save the changes.   Note:    To use the DHCP server function of this device, you should configure all the clients in the LAN in   "Obtain an IP Address automatically" mode. This function will take effect until this device reboots.   4.4.5 Profile   Profile function can help to remember the wireless networks you previously connected to. You can   Edit/Delete or Add items in this page for your later convenient reconnection.   Figure 4-13 Profile     Choose - You can choose the wireless network that you want to connect to.   Profile Name - The alias that you have given to your wireless networks. By default it's the   same as root SSID, but you can change it to any other name that you can easily remember   and distinguish.       SSID - The wireless network name of your root AP or wireless router.   MAC - The physical address of your root AP or wireless router, also called BSSID .   Security Type - The security type of your root wireless network.   Modify - You can Edit or Delete the profile(s).   Click Connect to connect the Entertainment Adapter to the wireless network you have chosen   from the profile list.   Click Add to add a new profile to the list.   Click Delete All to delete all the information in the profile list.   To add a profile:   the SSID of your root device (a wireless router or AP) and its MAC address, select the band and   the wireless security type of your root device and also enter the wireless password. Then click to   Save your profile.   17   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Figure 4-14 Add or Modify the Profile    Profile Name - The alias that you have given to your wireless networks. By default it's the   same as the Main Router/AP Wi-Fi Network Name(SSID), but you can change it to any   other name so that you can easily remember and distinguish.     Main Router/AP Wi-Fi Network Name - The wireless network name of your root device   this profile will connect to, it is also called SSID.   MAC Address of Main Router/AP - The MAC of your root device this profile will connect   to.     Band - The wireless band that the root access point or wireless router is working in.   Wireless Security Type - The security type of your root wireless networks this profile   refers to.       Encryption - The encryption of the existing wireless network. It is used when the   wireless security type is WPA-PSK or WPA2-PSK.   WEP Index - The WEP index is only used when the wireless security type is   WEP(ASCII) or WEP(Hexadecimal).   WEP Auth Type - The authorization type of WEP. It is only used when the wireless   security type is WEP(ASCII) or WEP(Hexadecimal).   Wireless Password - The wireless password of the existing wireless network. If the   Wireless Security Type is WPA-PSK or WPA2-PSK, the length of this field should be   between 8 and 63 characters which are case-sensitive. If the Wireless Security Type   is WEP(ASCII), the length should be 5 or 13 characters. If the Wireless Security   Type is WEP(Hexadecimal), the length should be 10 or 26 digits.   Click Save to save this piece of profile in the list and go back to the Profile List page.   Click Back to go back to the Profile List page.   3. After you’ve set and saved the profile, it will return to the profile list page and display as in   Figure 4-15 Add or Modify the Profile   18   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Click Edit to further edit the profile(s), or Delete to delete the profile(s).   Click Connect to connect the Entertainment Adapter to the wireless network that you have chosen   in the profile list.   Click Add to add a new profile to the list.   Click Delete All to delete all the information in the profile list.   4.5 System Tools   System Tools option helps you to optimize the configuration of your device. You can upgrade the   Entertainment Adapter to the latest version of firmware as well as backup or restore the   Entertainment Adapter’s configuration files. It’s suggested that you change the default password   to a more secure one because it controls access to the device’s web-based management page.   Besides, you can find out what happened to the system in System Log.   Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Clicking   any of them will enable you to configure the corresponding function. The detailed explanations for   each submenu are provided below.   Figure 4-16 The System Tools menu   4.5.1 Firmware Upgrade   Selecting System Tools > Firmware Upgrade allows you to upgrade the latest version of   firmware for the device on the screen shown in Figure 4-17.   Figure 4-17 Firmware Upgrade     Firmware Version - Here displays the current firmware version.   Hardware Version - Here displays the current hardware version. The hardware version of the   upgrade file must accord with the current hardware version.   19   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Note:    1. There is no need to upgrade the firmware unless the new firmware has a new feature you   want to use. However, when experiencing problems caused by the device itself, you can try to   upgrade the firmware.   2. Before upgrading the device’s firmware, you should write down some of your customized   settings to avoid losing important configuration settings of device.   To upgrade the device's firmware, follow these instructions:   1. Download   a more recent firmware upgrade file from the TP-LINK website   2. Enter the path name or click Browse… to select the downloaded file on the computer into the   File blank.   3. Click Upgrade.   Note:    Do not turn off the device or press the Reset button while the firmware is being upgraded. The   device will reboot after the Upgrading has been finished.   4.5.2 Factory Defaults   Selecting System Tools > Factory Default allows you to restore the factory default settings for   the device on the screen shown in Figure 4-18.   Figure 4-18 Restore Factory Defaults   Click Restore to reset all configuration settings to their default values.   • • • • Default User Name: admin   Default Password: admin   Default IP Address: 192.168.0.254   Default Subnet Mask: 255.255.255.0   Note:    Any settings you have saved will be lost when the default settings are restored.   4.5.3 Backup & Restore   Selecting System Tools > Backup & Restore allows you to save all configuration settings to your   local computer as a file or restore the device's configuration on the screen shown in Figure 4-19.   20   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Figure 4-19 Save or Restore the Configuration   Click Backup to save all configuration settings to your local computer as a file.   To restore the device's configuration, follow these instructions:   • • Click Browse… to find the configuration file which you want to restore.   Click Restore to update the configuration with the file whose path is the one you have input or   selected in the blank.   Note:    The current configuration will be covered with the uploading configuration file. Wrong process will   lead this device unmanaged. The restoring process lasts for 20 seconds and this device will restart   automatically then. Keep the power of this device on during the process, in case of any damage.   4.5.4 Reboot   Figure 4-20 Reboot the device   Click the Reboot button to reboot the device.   Some settings of the device will take effect only after rebooting, which include:    Change the LAN settings, such as LAN IP type, LAN IP, and so on (System will reboot   automatically).      Upgrade the firmware of this device (System will reboot automatically).   Restore this device's settings to the factory defaults (System will reboot automatically).   Update the configuration with the file (System will reboot automatically).   21   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   4.5.5 Password   Selecting System Tools > Password allows you to change the factory default user name and   password of the device on the screen shown in Figure 4-21.   Figure 4-21 Password   It is strongly recommended that you change the factory default user name and password of the   device. All users who try to access the device's web-based management page or Quick Setup will   be prompted for the device's user name and password.   Note:    The new user name and password must not exceed 14 characters in length and must not include   any spaces. Enter the new Password twice to confirm it.   Click Save when finished.   Click Clear All to clear all.   4.5.6 System Log   Selecting System Tools > System Log allows you to query the Logs of the device on the screen   shown in Figure 4-22.   Figure 4-22 System Log   22   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   The device can keep logs of all traffic. You can query the logs to find what happened to the device.     Log Type - By selecting the log type, only logs of this type will be shown.   Log Level - By selecting the log level, only logs of this level will be shown.   Click the Refresh button to show the latest log list.   Click the Save Log button to save all the logs in a txt file.   Click the Clear Log button to delete all the logs from the system permanently, not just from the   page.   Click the Next button to go to the next page, or click the Previous button return to the previous   page.   23   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Appendix A: Factory Defaults   Item   Default Value   Common Default Settings   Username   admin   Password   admin   IP Address   Subnet Mask   Domain   192.168.0.254   255.255.255.0   24   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Appendix B: Troubleshooting   T1. Can I power on TL-WA890EA by connecting it to a nearby device via the USB cable?   Sorry, you cannot. We strongly suggest to only use the power adapter attached in the package   for power supply, as the entertainment adapter TL-WA890EA may not gain enough power   supply from the other devices.   T2. What can I do if I cannot log in the web management page after I type tplinkadapter.net   in my browser?   2) Please make sure your hardware connection is OK. You can confirm this by the LAN LED on   the side panel of TL-WA890EA. If the LED of the LAN port, which your Ethernet cable is   connected to, is lighting blue, your hardware connection is OK; otherwise, please check your   hardware connection carefully.   3) Make sure your wired device’s IP address is set as “Obtain an IP address automatically”.   4) If the problem still persists, please feel free to contact our technical support.   T3. What should I do if my TL-WA890EA cannot connect to the main router/AP or its   performance is unsatisfactory after the successful connection?   1) If you use Method One to set up the connection, please make sure your main router/AP isn’t   using WEP as the wireless security, as the WPS 2.0 standard does not support WEP   encryption.   2) Please try another location where the TL-WA890EA is nearer to the main router/AP.   3) If your main router/AP is a dual-band product, please try to select 5GHz as its frequency   band.   4) Do not place it near any devices that might cause wireless interference, such as cordless   phones, blue tooth devices, microwave ovens, etc.   25   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Appendix C: Specifications   General   Standards and Protocols IEEE 802.3, 802.3u, 802.11n, 802.11b and 802.11g, TCP/IP, DHCP   Safety & Emission   Ports   CE   Four 10/100M Auto-Negotiation LAN RJ45 port   Wireless   Frequency Band   2.4GHz, 5GHz   11n:up to 300Mbps (2.4G), 300Mbps (5G)   11b:11/5.5/2/1M   Radio Data Rate   11a/11g:54/48/36/24/18/12/9/6M   Frequency Expansion   Modulation   DSSS (Direct Sequence Spread Spectrum)   DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM   WEP, WPA-PSK, WPA2-PSK   Security   270M: -68dBm@10% PER;   108M: -68dBm@10% PER;   54M: -72dBm@10% PER;   11M: -85dBm@8% PER;   6M: -88dBm@10% PER;   1M: -90dBm@8% PER   Sensitivity @PER   Physical and Environment   Working Temperature   0℃~40℃ (32℉~104℉)   Working Humidity   Storage Temperature   Storage Humidity   10% ~ 90% RH, Non-condensing   -40℃~70℃(-40℉~158℉)   5% ~ 95% RH, Non-condensing   26   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   Appendix D: Glossary    802.11a - Specification for wireless networking at 54 Mbps using OFDM modulation and   operating in radio band at 5GHz.    802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using   direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio   spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to   as Wi-Fi networks.     802.11g - Specification for wireless networking at 54 Mbps using direct-sequence   spread-spectrum (DSSS) technology, using OFDM modulation and operating in the   unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices,   and WEP encryption for security.   802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input   data throughput via spatial multiplexing and increased range by exploiting the spatial diversity,   perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium   (EWC) was formed to help accelerate the IEEE 802.11n development process and promote a   technology specification for interoperability of next-generation wireless local area networking   (WLAN) products.    DNS (Domain Name System) - An Internet Service that translates the names of websites into   IP addresses.     Domain Name - A descriptive name for an address or group of addresses on the Internet.   DoS (Denial of Service) - A hacker attack designed to prevent your computer or network from   operating or communicating.    DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over   existing traditional phone lines.     ISP (Internet Service Provider) - A company that provides access to the Internet.   MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be   transmitted.    SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key   identifying a wireless local area network. For the wireless devices in a network to   communicate with each other, all devices must be configured with the same SSID. This is   typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in   the wireless Access Point and to the wireless network name.      WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or   152-bit shared key algorithm, as described in the IEEE 802.11 standard.   Wi-Fi - A trademark of the Wi-Fi Alliance and the brand name for products using the IEEE   802.11 family of standards.   WLAN (Wireless Local Area Network) - A group of computers and associated devices   communicate with each other wirelessly, which network serving users are limited in a local   area.    WPA (Wi-Fi Protected Access) - WPA is a security technology for wireless networks that   improves on the authentication and encryption features of WEP (Wired Equivalent Privacy). In   27   Download from Www.Somanuals.com. All Manuals Search And Download.   TL-WA890EA N600 Universal Dual Band WiFi Entertainment Adapter with 4 Ports   fact, WPA was developed by the networking industry in response to the shortcomings of WEP.   One of the key technologies behind WPA is the Temporal Key Integrity Protocol (TKIP). TKIP   addresses the encryption weaknesses of WEP. Another key component of WPA is built-in   authentication that WEP does not offer. With this feature, WPA provides roughly comparable   security to VPN tunneling with WEP, with the benefit of easier administration and use. This is   similar to 802.1x support and requires a RADIUS server in order to implement. The Wi-Fi   Alliance will call this, WPA-Enterprise. One variation of WPA is called WPA Pre Shared Key   or WPA-Personal for short - this provides an authentication alternative to an expensive   RADIUS server. WPA-Personal is a simplified but still powerful form of WPA most suitable for   home Wi-Fi networking. To use WPA-Personal, a person sets a static key or "passphrase" as   with WEP. But, using TKIP, WPA-Personal automatically changes the keys at a preset time   interval, making it much more difficult for hackers to find and exploit them. The Wi-Fi Alliance   will call this, WPA-Personal.   28   Download from Www.Somanuals.com. All Manuals Search And Download.   |