Sunrise Medical Mobility Aid Quickie S 525 User Manual

Quickie S-525

User

Instruction

Manual &

Warranty

SUPPLIER:

THIS MANUAL MUST BE GIVEN TO THE

RIDER OF THIS WHEELCHAIR.

RIDER:

BEFORE USING THIS WHEELCHAIR

READ THIS ENTIRE MANUAL AND SAVE

FOR FUTURE REFERENCE.

Download from Www.Somanuals.com. All Manuals Search And Download.

1 1 . T A B L E O F C O N T E N T S

VIII. TIPS FOR ATTENDANTS .............................................................. 26

A. To Climb a Curb or Single Step ...................................................... 26

B. To Descend a Curb or Single Step ................................................ 26

IX. SET UP,ADJUSTMENT & USE .................................................... 27

Notes .......................................................................................................... 27

ToolsYou Will Need ................................................................................ 28

Check Out.................................................................................................. 28

A. Battery Removal.................................................................................. 29

B. Swing-Away Footrests........................................................................ 29

C. Elevating Legrest (Optional) ............................................................ 30

D. Remote Joystick Installation (Optional) ........................................ 30

E. To Adjust the Height of the Remote Joystick .............................. 30

F. Joystick Swing-Away Retractable Mount (Optional) .................. 31

G. Dual-Post Height-Adjustable Armrests.......................................... 31

H. Height-Adjustable Armrests (Optional) ........................................ 32

I. Armrest Width Adjustment .............................................................. 33

J. Armrest Angle Adjustment................................................................ 33

K. Backrest ................................................................................................ 34

L. Folding Backrest (Seat Frame Only) (Optional) .......................... 35

M. Seat Depth (Seat Frame and Contour Seats Only) .................... 35

N. Parapak Seat Sling (Seat Frame Only) ............................................ 36

O. Seat Height & Angle Adjustment...................................................... 36

P. Wheel Locks ........................................................................................ 36

Q. Check-Out............................................................................................ 37

X. OPERATING GUIDE ........................................................................ 38

A. Performance Control Settings.......................................................... 38

B. QTRONIX Programming Pad (Optional)...................................... 38

C. Thermal Roll-Back .............................................................................. 39

D. Circuit Breakers .................................................................................. 39

E. Integral Joystick.................................................................................... 40

F. Remote Joystick Assembly (Optional)............................................ 41

G. Motor Locks ........................................................................................ 42

X1. BATTERIES ............................................................................................ 43

A. Introduction.......................................................................................... 43

B. Battery Charger .................................................................................. 43

C. Acid Burns ............................................................................................ 44

D. Connecting Batteries in Battery Box(es) ...................................... 44

E. Charging Batteries .............................................................................. 45

F. Disposing of Batteries........................................................................ 46

XII. MAINTENANCE.................................................................................. 47

A. Notes...................................................................................................... 47

B. Cleaning ................................................................................................ 47

C. Storage Tips .......................................................................................... 47

D. Battery Maintenance .......................................................................... 48

E. Pneumatic Tires.................................................................................... 49

F. To Repair or Replace a Tire.............................................................. 49

G. Motor Brushes .................................................................................... 50

H. Ordering Parts .................................................................................... 50

I. Maintenance Chart.............................................................................. 51

XIII. WIRING DIAGRAMS ........................................................................ 52

XV. SUNRISE LIMITED WARRANTY .............................................. 54

1. INTRODUCTION ..............................................................................

11. TABLE OF CONTENTS ..................................................................4 - 5

111. YOUR CHAIR AND ITS PARTS ..................................................6 - 7

IV. NOTICE - READ BEFORE USE ..................................................

V. EMI (ELECTROMAGNETIC INTERFERENCE) ..................

A. What is EMI..........................................................................................

B. What Effect Can EMI Have ..............................................................

C. Sources of EMI ....................................................................................

D. Distance From the Source................................................................ 10

E. Immunity Level .................................................................................... 10

F. Report All Suspected EMI Incidents................................................ 11

VI. GENERAL WARNINGS.................................................................... 12

A. Notice to Rider .................................................................................. 12

B. Notice to Attendants ........................................................................ 12

C. Weight Limit ........................................................................................ 13

D. Controller Settings.............................................................................. 13

E. EMI.......................................................................................................... 13

F. Safety Check-List ................................................................................ 13

G. Changes & Adjustments .................................................................... 14

H. When Seated in a Parked Wheelchair............................................ 14

I. Environmental Conditions ................................................................ 14

J. Terrain.................................................................................................... 15

K. Street Use ............................................................................................ 15

L. MotorVehicle Safety .......................................................................... 15

M. Center of Balance .............................................................................. 15

N. Transfers................................................................................................ 16

O. Reaching or Leaning............................................................................ 17

P. Dressing or Changing Clothes ........................................................ 17

Q. Obstacles .............................................................................................. 18

R. Driving in Reverse .............................................................................. 18

S. Ramps, Slopes & Side Hills ................................................................ 18

T. To Reduce the Risk of Falls,Tip-over or Loss of Control ........ 19

U. Ramps at Home & Work .................................................................. 20

V. Wheelchair Lifts .................................................................................. 20

W.Curbs & Single Steps .......................................................................... 21

X. Stairs ...................................................................................................... 21

Y. Escalators .............................................................................................. 21

VII. WARNINGS: COMPONENTS & OPTIONS ........................ 22

A. Anti-Tip Levers .................................................................................... 22

B. Armrests................................................................................................ 22

C. Batteries ................................................................................................ 22

D. Cushion & Sling Seats ........................................................................ 22

E. Fasteners .............................................................................................. 22

F. Footrest ................................................................................................ 23

G. Motor Lock .......................................................................................... 23

H. On/Off Switch .................................................................................... 23

I. Pneumatic Tires.................................................................................... 23

J.Positioning Belts (Optional) ................................................................ 24

K. Push Handles........................................................................................ 24

L. Rear Wheel Locks (Optional) .......................................................... 24

M. Seating Systems.................................................................................... 25

N. Upholstery Fabric................................................................................ 25

O. Suspension ............................................................................................ 25

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

1 1 1 . Y O U R C H A I R A N D I T S P A R T S

QUICKIE S-525

Weight

posite footplates and heel loops.

Option - elevating legrests, multiposi-

tional and angle-adjustable footplate

105 lb.With swing-away footrests

and armrests, without batteries

Drive Wheels

Casters

12" Mag

Standard - 8" airless insert

Tire types:

Option - 8" solid, 8" pneumatic

Standard - pneumatic

Option - airless insert, solid

Joystick

Armrests

Standard - dual post flip back

Option - height-adjustable dual post

or single post with desk or full

length waterfall pads

Standard - integral (right-hand

or left-hand mount)

Optional - remote (right-hand

or left-hand mount)

Option - swing-away retractable

joystick (remote only)

Batteries

Wheel Locks

Option - Push-to-lock

Option - 6" extension handles

Drives

Right-angle PosiDrive

(2 deep cycle batteries required

to operate chair)

All features may not be available with

some chair setups or in conjunction

with another chair feature. Please

consult your supplier for more

information.Your authorized supplier

can also provide you with more

information on accessories.

Option - 22 NF deep cycle gel,

U1 deep cycle gel

Battery Charger

Standard - off board (Lester)

Colors

Refer to current order form

Chair Parts

Standard - black

Seat Frame Dimensions

Seat Frame width: standard - 14"-20"

Seat depth: 14"-18" adjustable

Seat sling: Standard-parapak

Option- Aluminum pan

Option Cushions: Jay Cushions

Optional - Contour Seat

or High Back Contour Seat

Backrest

Standard - Non-folding: 15" - 20"

Option - Folding: 15" - 20"

Straight Backpost or 8° bend

Footrest

Q U I C K I E S - 5 2 5

1. Push Handle

2. Single-post,

9. Backrest

10. Backrest pivot plate

11. Battery box

height-adjustable armrest

3. Integral joystick controller

4. Seat cushion (optional)

5. Swing-away footrest latch plate

6. Swing-away footrest hanger

7. Heel loop

12. 12"x3" PosiDrive Wheels

13. Swing-away, quick release

footrest lever

14. Caster housing

15. 8" Solid casters

16. Caster Fork

Standard - Swing-away with com-

8. Composite footplate

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

1 V . N O T I C E — R E A D B E F O R E U S E

V . E M I ( E L E C T R O M A G N E T I C I N T E R F E R E N C E )

A. CHOOSE THE RIGHT CHAIR & SAFETY OPTIONS

Sunrise provides a choice of many power wheelchair styles, sizes and adjust-

ments to meet the needs of the rider. However, final selection of a wheelchair

rests solely with you and your health care professional. Choosing the best

chair for you depends on such things as:

1. Your size, disability, strength, balance and coordination.

2. Your intended use, and your level of activity.

3. The types of hazards you must overcome in daily use (in areas where you are

likely to use your chair).

Heed all warnings to reduce the risk of unintended brake release or chair movement:

1. Beware of the danger from hand-held transceivers. Never turn on or use a

hand-held transceiver while power to your chair is on. Use extra care if you

believe that such a device may be in use near your chair.

2. Be aware of nearby radio orTV stations, and avoid coming close to them.

3. If unintended movement occurs, turn your chair off as soon as it is safe to do so.

A. WHAT IS EMI?

4. The need for options for your safety and comfort (such as positioning belts

or special seat systems).

1. EMI means: electromagnetic (EM) interference (I). EMI comes from radio wave

sources such as radio transmitters and transceivers. (A “transceiver” is a

device that both sends and receives radio wave signals).

2. There are a number of sources of intense EMI in your daily environment.

Some of these are obvious and easy to avoid. Others are not, and you may not

be able to avoid them.

B. ADJUST CHAIR TO YOUR ABILITY

You need to work with your doctor, nurse or therapist, and your supplier, to

fit this chair and adjust the controller settings for your level of function and

ability level.

C. REVIEW THIS MANUAL OFTEN

3. Powered wheelchairs may be susceptible to electromagnetic interference (EMI)

emitted from sources such as radio stations,TV stations, amateur radio (HAM)

transmitters, two-way radios, and cellular phones.

Before using this chair you, and each person who may assist you, should read

this entire Manual and make sure to follow all instructions. Review the warnings

often, until they are second nature to you.

4. EMI can also be produced by conducted sources or electo-static discharge (ESD).

D. WARNINGS

B. WHAT EFFECT CAN EMI HAVE?

The word “WARNING” refers to a hazard or unsafe practice that may cause

severe injury or death to you or to other persons.The “Warnings” are in four

main sections, as follows:

1. EMI can cause your chair, without warning, to:

1. V. — EMI

•

Release its brakes

Move by itself

Move in unintended directions

Here you will learn about electomagnetic interference and how it can affect

your chair.

1. VI — GENERAL WARNINGS

Here you will find a safety checklist and a summary of risks you need to be

aware of before you ride this chair.

2. VII — WARNINGS — COMPONENTS & OPTIONS

Here you will learn about your chair. Consult your supplier and your

health care professional to help you choose the best set-up and options

for your safety.

If any of these occurs, it could result in severe injury to you or others.

2. EMI can damage the control system of your chair.This could create a safety

hazard, and lead to costly repairs.

C. SOURCES OF EMI

The sources of EMI fall into three broad types:

1. Hand-Held Transceivers:

3. XI — BATTERIES

Here you will learn about battery and charger safety, and how to avoid injury.

The antenna is usually mounted directly on the unit.These include:

•

Citizens band (CB) radios

“Walkie-talkies”

Security, fire and police radios

Cellular phones

Lap-top computers with phone or fax

Other personal communication devices

Note: Where they apply, you will also find

“Warnings” in other sections of this Manual.

Note: These devices can transmit signals while they are on, even if not in use.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V . E M I ( E L E C T R O M A G N E T I C I N T E R F E R E N C E )

2. Medium-Range MobileTransceivers:

•

4-Zero Touch Switch

5-Zero Touch Switch

These include two-way radios used in police cars, fire trucks, ambulances and

taxi cabs.The antenna is usually mounted on the outside of the vehicle.

3. Long-RangeTransceivers:

c) Specialty input devices with an unknown immunity level because the devices

were not tested with the S-525 and QTRONIX controller include:

• Treadle Switch

These include commercial radio and TV broadcast antenna towers and

amateur (HAM) radios. Note: The following are not likely to cause EMI problems:

Lap-top computers (without phone or fax), Cordless phones,TV sets or

AM/FM radios, CD or tape players.

•

Ribbon Switch

Disc Switch

Buddy Button

Micro Light

Star Board

Penta Switch

Plate Switch

Soft Switch

D. DISTANCE FROM THE SOURCE

EM energy rapidly becomes more intense as you get closer to the source.

For this reason, EMI from hand-held devices is of special concern.

(See C.1 above) A person using one of these devices can bring high levels

of EM energy very close to your chair without you knowing it.

Grasp Switch

• Wobble Switch

E. IMMUNITY LEVEL

1. The level of EM energy is measured in volts per meter (V/m). Every power

wheelchair can resist EMI up to a certain level.This is called its “immunity level”.

2. The higher the immunity level, the less the risk of EMI. It is believed that a

20V/m immunity level will protect the power wheelchair user from the more

common sources of radio waves.

Individuals with physical limitations requiring the use of a specialty control input device

known not to be immune to 20V/m, or not known, should exercise extra care around

known sources of EMI.

3. The configurations tested and found to be immune to at least 20V/m are:

Quickie S-525 power wheelchair with a right-hand mounted Penny & Giles Pilot

integral controller, 16” seat width, 16” seat depth, single-post height adjustable

armrest, swing-away hanger and U1 gel cell batteries.

There is no way to know the effect on EMI if you add accessories or modify this chair.

Any change to your chair may increase the risk of EMI. Parts from other suppliers have

unknown EMI properties.

Quickie S-525 power wheelchair with a right hand mounted QTRONIX remote

joystick system, 16” seat width, 16” seat depth, single-post height adjustable arm-

rests, swing-away hangers and U1 gel cell batteries.

F. REPORT ALL SUSPECTED EMI INCIDENTS

4. a) Specialty input devices tested with the S-525 and QTRONIX controller

that were found to be immune to 20V/m include:

You should promptly report any unintended movement or brake release.

Be sure to indicate whether there was a radio wave source near your chair

at the time.

•

Breath Control

Heavy Duty Switched Joystick

Proportional Head Control

Contact: Sunrise Medical Customer Service Department at (800) 333-4000

• Wafer Board

b) Specialty input devices tested with the S-525 and QTRONIX controller that

were found NOT to be immune to 20V/m include:

• Tri-Switch Head Array

•

Proportional Mini-Joystick/Chin Control

Proximity Head Array

Zero Touch Switch

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G E N E R A L W A R N I N G S

V 1 .

G E N E R A L W A R N I N G S

C. WEIGHT LIMIT

Heed all warnings in this section. If you fail to do so a fall, tip-over or loss of control

may occur and cause severe injury to you or others.

1. Never exceed a total weight of 250 pounds (113.6 kilograms) or 350 pounds

(158.8 kilograms) with heavy duty option, for rider plus items carried.

2. Never use this chair for weight training if the total weight (rider plus addition-

al weights) exceeds 250 pounds (113.6 kilograms) or 350 pounds (158.8 kilo-

grams) with heavy duty option.

3. Exceeding the weight limit is likely to damage the seat, frame, or fasteners and

may cause severe injury to you or others from chair failure.

A. NOTICE TO RIDER

1. Before using this chair, you should be trained in its safe use by your health

care professional.

2. Every wheelchair is different.Take the time to learn the feel of this chair

before you begin riding.

4. Exceeding the weight limit will void the warranty.

D. CONTROLLER SETTINGS

3. Be aware that you must develop your own methods for the safe use of this

chair that are best suited to your level of function and ability.

4. Have someone help you practice bending, reaching and transfering until you

learn how to do them safely.

5. Never try a new maneuver on your own unless you are sure it is safe.

6. Get to know the areas where you plan to use your chair. Look for hazards and

learn how to avoid them.

Be aware that you may need to adjust the controller settings of your chair to

reduce the risk of a collision, fall or tip-over.

1. Check and adjust the settings every six to twelve months (or more often,

if needed).

2. Consult your supplier to adjust the control settings immediately if you notice

any change in your ability to:

•

Control the joystick.

Hold your torso erect.

Avoid running into objects.

B. NOTICE TO ATTENDANTS

E. EMI

Make sure you heed all warnings and follow all instructions in each section of

this manual. (Be aware that warnings that apply to the rider also apply to you).

NOTES:

1. You need to work with the rider, and the rider’s doctor, nurse or therapist, to

develop safe methods best suited to your abilities and those of the rider.

2. To manually push the chair you must release the motor locks.

Read SectionV to learn about EMI.To reduce the risk of unintended brake

release or chair movement:

1. Never turn on or use a hand-held transceiver while power to your chair is on.

Use extra care if you believe that such a device may be in use near your chair.

2. Be aware of nearby radio or TV stations, and avoid coming close to them.

3. If unintended movement or brake release occurs, turn your chair off as soon

as it is safe.

•

Make sure you have full control over the chair when you release the

motor locks.When you do so the chair will not have brakes.

3. Propel this chair by the push handles only.They provide secure points for

you to hold the rear of the chair to prevent a fall or tip-over.

F. SAFETY CHECK-LIST

•

Check to make sure push handle grips will not rotate or slip off.

Before each use of this chair:

HELPING THE RIDER OVERCOME AN OBSTACLE:

1. To prevent injury to your back, use good posture and proper body mechanics.

When you lift or support the rider or tilt the chair, bend your knees slightly

and keep your back as upright and straight as you can.

2. Before each maneuver, tell the rider what you plan to do, and explain what you

expect the rider to do.This will put the rider at ease and reduce the risk

of an accident.

1. Make sure the chair operates smoothly. Check for noise, vibration, or a change

in ease of use. (They may indicate low tire pressure, loose fasteners, or damage

to your chair).

•

If you detect a problem, make sure to repair or adjust the chair. Deferring

repair or adjustment could increase the risk for injury. Your supplier can

help you find and correct the problem.

2. Make sure batteries are charged. Green lights on charge indicator will light up

when charge is full.Yellow lights indicate battery charge level is getting low.

Red lights indicate batteries are in immediate need of charging.

3. Go straight up and straight down a curb or stair. If you turn, or climb or

descend at an angle, a fall or tip-over is likely.

4. Remind the rider to lean back when you tilt the chair backward.

5. Lower the chair slowly. Do not let the chair drop to the pavement or ground.

Doing so may damage the chair or injure the rider.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G E N E R A L W A R N I N G S

V I .

G E N E R A L W A R N I N G S

G. CHANGES & ADJUSTMENTS

J. TERRAIN

1. This chair is designed for use on firm, even surfaces such as concrete, asphalt

and indoor flooring.

2. Do not operate your chair in sand, loose soil or over rough terrain. Doing so

may damage wheels, bearings, axles or motors, or loosen fasteners.

Never use non-Quickie parts or make a changes to your chair unless authorized

by Sunrise. (Doing so will void theWarranty, and may create a safety hazard).

1. If you modify or adjust this chair it may increase the risk of a fall or tip-over.

2. Modifications unauthorized by Sunrise constitutes remanufacturing of the

wheelchair.This voids the warranty.The rider then assumes all future liability

for the wheelchair.

K. STREET USE

H. WHEN SEATED IN A PARKED WHEELCHAIR

In most states, power chairs are not legal for use on public roads. Be alert to

the danger of motor vehicles on roads or in parking lots.

1. At night, or when it is hard to see, use reflective tape on your chair and clothing.

2. It may be hard for drivers to see you. Make eye contact with drivers before

you proceed.When in doubt, yield until you are sure it is safe.

1. Always turn off all power to your chair when you are parked, even for a

moment.This will prevent:

•

Accidental movement from contact with the joystick by you or others.

Unintended brake release or movement from EMI sources. (See SectionV)

L. MOTOR VEHICLE SAFETY

2. Make sure that persons who help you (for example, store clerks) are aware

of the joystick and do not touch it. If they do, your chair may move suddenly

when you do not expect it.

To date, the U.S. Department of Transportation has not approved any tie down

system for transporting a wheelchair in a motor vehicle.

1. Never sit in this chair while in a moving vehicle. In an accident or sudden

stop you may be thrown from the chair.

I. ENVIRONMENTAL CONDITIONS

Your chair is not designed for use in a heavy rain storm, or in snowy or icy conditions.

1. Contact with water or excessive moisture can cause an electrical

malfunction.The frame, motors and other chair parts are not water-tight

and may rust or corrode from the inside.To avoid a chair failure:

•

Wheelchair belts are designed to position the rider only and will not protect you

in an accident; further injury may result from the belts.

2. Always move to an approved vehicle seat.You must be secured with proper

motor vehicle restraints.

3. Never transport this chair in the front seat of a vehicle. It may shift and

interfere with the driver.

•

Minimize exposure of your chair to a rain storm or very wet conditions.

Never take your chair into a shower, tub, pool or sauna.

Do not use your chair in fresh or salt water (such as at the edge of a

stream, lake, or ocean).

4. Always secure this chair so that it cannot roll or shift.

M.CENTER OF BALANCE

•

Make sure battery cover is secure.

Replace joystick boot if it becomes torn or cracked.

Make sure all electrical connections are secure.

The point where this chair will tip forward, back, or to the side depends on its

center of balance and stability.

Dry the chair as soon as you can if it gets wet, or if you use water to clean it.

2. Proceed slowly and use extra care if you must operate your chair on a wet

or slick surface.

THE CENTER OF BALANCE IS AFFECTED BY:

1. The seat height and seat angle.

2. A change in your body position, posture or weight distribution.

3. Using this chair on a ramp or slope.

•

Do so only if you are sure it is safe.

Stop if one or both main wheels lose traction. If this occurs, you may lose

control of your chair or fall.

4. The use of a back pack or other options, and the amount of added weight.

•

Never operate your chair on a slope or ramp if there is snow, ice, water

or oil film present.

When in doubt, have someone help you.

TO REDUCE THE RISK OF A FALL OR TIP-OVER:

1. Consult your supplier for information on modifications authorized by

Sunrise before you modify or adjust this chair.

•

Note:You may need to make additional changes to correct the center of balance.

2. Use extreme care until you know the balance points of this chair and how to

avoid a fall or tip-over.

3. When not in use, keep your chair in a clean, dry place.

Extra caution should be used when employing the disc switch or the proximity

head array as control devices. These two devices are susceptible to

malfunction when wet.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G E N E R A L W A R N I N G

V I .

G E N E R A L W A R N I N G S

N.TRANSFERS

O. REACHING OR LEANING

Reaching or leaning affects the center of balance of your chair. If done improperly,

a fall or tip-over is likely.When in doubt, ask for help or use a device to extend

your reach.

It is dangerous to transfer on your own. It requires good balance and agility.

Be aware that there is a point during every transfer when the wheelchair seat

is not below you.To avoid a fall:

TO REDUCE THE RISK OF INJURY AND/OR DAMAGE TO THE

CHAIR:

1. Never reach or lean if you must shift your weight sideways or rise up off the seat.

2. Never reach or lean if you must move forward in your seat to do so.Always

keep your buttocks in contact with the backrest.

1. Always turn off power before you transfer to or from your chair. If you fail

to do so you may touch the joystick and cause your chair to move when you

do not expect it.

2. Make sure motor locks are engaged.This keeps the chair from moving when

you transfer.

3. Never reach with both hands (you may not be able to catch yourself to prevent a

fall if you lose your balance).

4. Never try to pick up an object from the floor by reaching down between

your knees.

3. Work with your health care professional to learn safe methods.

•

Learn how to position your body and how to support yourself during a transfer.

Have someone help you until you are sure you can do a safe transfer

on your own.

5. Never put pressure on the footrests while reaching.This may cause the chair

to tip if you lean too far.

4. Move your chair as close as you can to the seat you are transferring to.

If possible, use a transfer board.

6. Never reach or lean over the top of the seat back.This may damage the back-

rest and cause you to fall.

5. Rotate the front casters until they are as far forward as possible.

6. Be careful of the footrests. If you can, remove or swing them out of the way.

•

Never stand on footrests when you transfer. Doing so may damage them or

cause your chair to tip.

IF YOU MUST REACH OR LEAN; DO SO AT YOUR OWN RISK.

Remember to:

1. Move your chair as close as you can to the object you wish to reach.

2. Rotate the front casters until they are as far forward as possible.This makes the

chair more stable.

•

Make sure your feet do not “hang up” or get caught in the space between

the footrests.

7. Make sure armrests do not interfere.

Note:To do this: Move your chair past the object you want to reach, then back

up alongside it. Backing up will rotate the casters forward.

3. Turn off all power to your chair. If you fail to do so, you may touch the joystick

and cause your chair to move when you do not expect it.

4. Firmly grasp a rear wheel or an armrest with one hand.This will help to

prevent a fall if the chair tips.

8. Transfer as far back onto the seat surface as you can.This will reduce the risk

that you will miss the seat or fall.

P. DRESSING OR CHANGING CLOTHES

Be aware that your weight will shift if you dress or change clothes while seated

in this chair.To make the chair more stable, rotate the front casters until they

are forward.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G E N E R A L W A R N I N G S

V I .

G E N E R A L W A R N I N G S

Q. OBSTACLES

T. TO REDUCE THE RISK OF A FALL,

TIP-OVER OR LOSS OF CONTROL:

Obstacles you may have to overcome in daily use include door thresholds, lifts,

ramps and hazards such as potholes and broken pavement.These can damage

your chair and may cause a fall, tip-over or loss of control.

1. Never use your chair on a slope unless

you are sure you can do so without

losing traction.

2. Always go as straight up and as straight

down as you can.

1. Be aware that thresholds are very dangerous. (Even a small change in height

may stop a caster wheel and cause your chair to tip). You may need to:

•

Remove or cover threshold strips between rooms.

Install a ramp at entry or exit doors.

•

Do not“cut the corner” on a slope

or ramp.

2. Keep your eyes moving when you ride; scan the area well ahead of your chair.

3. Make sure the floor areas where you use this chair are level and free of obstacles.

4. To help correct your center of balance:

•

Do not turn or change direction

on a slope.

Fig. 1

•

Lean your upper body forward slightly as you go up over an obstacle.

Press your upper body backward as you go down from a higher to

a lower level.

3. Always stay in the center of the ramp. Make

sure ramp is wide enough that you are not

at risk that a wheel may roll off the side.

4. Lean or press your body uphill.This will

help adjust for a change in the center of

balance caused by the slope. (Fig. 1)

5. Keep your chair moving at a slow,

steady speed. Keep control over the

chair at all times.

R. DRIVING IN REVERSE

Use extra care when you drive your chair in reverse.You may lose control or

fall if one of the rear wheels hits an object.

1. Operate your chair slowly and at an even speed.

2. Stop often and check to make sure your path is clear of obstacles.

•

On a descent, do not let your chair

accelerate beyond its normal speed.

If the chair picks up speed, center the

joystick to slow down or stop.

S. RAMPS, SLOPES & SIDE HILLS

•

The center of balance of your chair changes when you are on a slope.

Note: “Slope” includes a ramp or side hill.Your chair is less stable when it is at an

angle. Never use this chair on a slope unless your are sure it is safe.When in doubt,

Note: The solid state controller of your chair

has a logic system that will help control your

speed when driving on a slope or up hill.

have someone help you.

Beware Of:

1. Steep slopes. Do Not use this chair on a slope steeper than 10%. (A 10% slope

means: One foot in elevation for every ten feet of slope length).

2. Wet or slippery surfaces (such as when ice, snow, water or oil film is present).A loss

of traction may cause a fall or tip-over.

•

If you stop, re-start slowly.

6. Never use rear wheel locks to try to

slow or stop your chair.This is likely to

cause the chair to veer out of control.

3. A change in grade on a slope (or a lip, bump or depression).These may

cause a fall or tip-over.

4. A drop-off at the bottom of a slope. (A drop-off of as small as 3/4 inch can stop a

front caster and cause the chair to tip forward).

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G E N E R A L W A R N I N G S

V I .

G E N E R A L W A R N I N G S

U. RAMPS AT HOME & WORK

W. CURBS & SINGLE STEPS

Make sure ramps meet all Building Codes for your area.

1. For your safety, have a licensed contractor build or remodel ramp to meet

all standards.

2. Note: The proper design will vary, depending on such things as: the length and height

of the ramp; the need for an intermediate platform; landing size; doors, and the direction

of swing, and; whether the ramp includes a turn or angle.

1. Your chair is not designed to drive up or down a curb or step more than

two (2) inches high. Doing so may:

•

Result in a fall or tip-over.

Damage the frame, wheels, axles or other chair parts, or loosen fasteners.

2. To prevent a fall or tip-over, use wheelchair access ramps or have someone

help you.

3. If you must climb or descend a curb or step alone do so at your own risk

and use extreme care.

At A Minimum:

1. Open sides of ramp must have side rails to prevent your chair from going

over the edge.

2. Slope must not be steeper than one inch in height for every one foot of

slope length.

3. Ramp surface must be even, and have a non-skid surface.

4. You may need to add a section at the top or bottom to avoid a lip or drop-off.

5. Ramp must be sturdy.Add bracing if needed, so ramp does not “bow” when

you ride on it.

•

Go as straight up or straight down as you can. Never turn or climb or

descend at an angle as a fall or tip-over is likely.

Proceed slowly, at a steady speed.

•

4. Make sure that persons who assist you review the “Tips For Attendants”

and heed all warnings.

X. STAIRS

V. WHEELCHAIR LIFTS

Never use this chair to go up or down stairs, even with an attendant.

Doing so is likely to cause a fall or tip-over.

Wheelchair lifts are used in vans, buses, and buildings to help you move from

one level to another.

Y. ESCALATORS

1. Always turn off all power to your chair when you are on a lift. If you fail to

do so, you may touch the joystick by accident and cause your chair to drive

off the platform. (Be aware that a “roll-stop” at the end of the platform may

not prevent this).

Never take this chair on an escalator, even with an attendant. Doing so is

likely to cause a fall or tip-over.

2. Make sure there is not a lip or drop-off at the top or bottom of the platform.

These may cause a fall or tip-over.When in doubt, have someone help you.

3. Always position the rider securely in the chair to help prevent falls while on a lift.

4. Avoid moving forward if a wheel is “hung up” on the lip of the ramp. Backup,

reposition the caster for a more direct approach.And slowly try again.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I I .

W A R N I N G S : C O M P O N E N T S

O P T I O N S

V I I .

W A R N I N G S : C O M P O N E N T S

O P T I O N S

F. FOOTRESTS

Note: If you use parts or make changes not authorized by Sunrise it may

create a safety hazard and will void the Warranty.

1. At the lowest point, footrests should be at least 2 1/2 inches off the ground. If

set too LOW, they may “hang up” on obstacles you can expect to find in normal

use.This may cause the chair to stop suddenly and tip forward.

2. To avoid a trip or fall when you transfer:

A. ANTI-TIP LEVERS

Never remove or alter anti-tip levers.They help keep your chair from tipping

over backward in normal use. Make sure rubber rollers are in good condition.

•

Make sure your feet do not “hang up” or get caught in the space

between the footrests.

•

Avoid putting weight on the footrests, as the chair may tip forward.

Remove or swing the footrests out of the way, if possible.

B. ARMRESTS

3. Never lift this chair by the footrests. Footrests detach and will not bear

the weight of this chair. Lift this chair only by non-detachable parts of the

main frame.

Armrests detach and will not bear the weight of this chair.

1. Never lift this chair by its armrests.They may come loose or break.

2. Lift this chair only by non-detachable parts of the main frame.

G. MOTOR LOCKS

C. BATTERIES

1. Do not engage or disengage motor locks unless power to the chair is off.

2. With either one or both brakes released, the chair will not operate and the

battey charge indicator will flash 9 bars rapidly (if power to the chair is on).

3. Be aware that the chair will not have brakes when motor locks are in the

free-wheel position.

1. Only deep cycled sealed case construction batteries should be used in this

device.

2. To prevent an acid spill, always keep batteries upright (wet cell batteries only).

3. Never smoke or hold an open flame near batteries.They are a known

explosion hazard.

4. Make sure that the person pushing the chair has full control when motor

locks are disengaged.

4. Always wear rubber gloves and safety glasses when you handle batteries.

5. Read all of section XI Batteries before attempting to change or charge batteries.

H. ON/OFF SWITCH

D. CUSHIONS & SLING SEATS

1. Never use the ON/OFF switch to stop the chair except in an emergency.

This will result in an abrupt stop, and may cause you to fall.

2. To slow your chair to a stop, return the joystick to neutral.

1. Quickie sling seats, standard foam cushions, and other body supports, are not

designed for the relief of pressure.

2. If you suffer from pressure sores, or if you are at risk that they will occur, you

may need a special seat system or a device to control your posture.

I. PNEUMATIC TIRES

•

Consult your doctor, nurse or therapist to find out if you need such a

device for your well-being.

Proper inflation extends the life of your tires and makes your chair easier to use.

1. Do not use this chair if any of the tires are under- or over-inflated. Check

weekly for proper inflation level, as listed on the tire sidewall.

2. Low pressure in a tire may cause the chair to veer to one side and result in a

loss of control.

3. An over-inflated tire may burst.

4. Never use a gas station air pump to inflate a tire. Such pumps provide air at

high volume, and could cause the tire to burst.To prevent tire damage:

E. FASTENERS

Many of the screws, bolts and nuts on this chair are special high-strength

fasteners. Use of improper fasteners may cause your chair to fail.

1. Only use fasteners provided by Sunrise.

2. If fasteners become loose, tighten them as soon as you can.

3. Over- or under-tightened fasteners may fail or cause damage to chair parts.

•

Use a hand pump (or a low volume air pump) to inflate tires.

Use a tire gauge to check pressure.

•

See Section IX,“Set-Up. Adjustment, & Use”, for proper torque settings.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I I .

W A R N I N G S : C O M P O N E N T S

O P T I O N S

V I I .

W A R N I N G S : C O M P O N E N T

O P T I O N S

5. Driving over sharp objects may cause damage to pneumatic tires and tubes.

6. This device has a feature known as a “split rim”, which eases tire service

and/or replacement.Air pressure should be removed from pneumatic tires

beofre attempting to split the rim.

M.SEATING SYSTEMS

1. Use of a seating system not approved by Sunrise may alter the center of

balance of this chair.This may cause a fall or tip-over.

2. Never change the seating system of your chair unless you consult your

supplier first.

J. POSITIONING BELTS (OPTIONAL)

Use a positioning belt only to help support your posture. Improper use of

such belts may cause severe injury or death.

N.UPHOLSTERY FABRIC

1. Make sure you are not at risk to slide down in the wheelchair seat. If this occurs,

you may suffer chest compression or suffocate due to pressure from the belt.

2. A pelvic wedge or a similar device can help keep you from sliding down in the

seat. Consult your health care professional to find out if you need such a device.

3. The belt must be snug, but must not be so tight that it interferes with breathing.You

should be able to slide your open hand, flat, between the belt and your stomach.

4. Make sure you can easily remove the belt in an emergency.

5. Never use a positioning belt:

1. Replace worn or torn fabric of seat sling and seat back as soon as you can. If

you fail to do so, the seat may fail and cause you to fall.Worn fabrics may

increase the potential for a fire hazard.

2. Sling fabric will deteriorate with age and use. Look for fraying, thin spots, or

stretching of fabric at rivet holes. Replace fabric as required.

3. “Dropping down” into sling seat will weaken fabric and result in the need to

inspect and replace sling on a more frequent basis.

•

In place of a motor vehicle seat belt. In an accident or sudden stop you

may be thrown from the chair.A positioning belt will not prevent this,

and further injury may result from the belt.

4. Be aware that washing may reduce flame retardation of the fabric.

O. SUSPENSION

•

As a restraint.A restraint requires a doctor’s order.

On a rider who is comatose or agitated.

The S-525 (optional) suspension system does contain Dry Natural Rubber.The

suspension, or any other component on the chair, does not contain any latex

based product.The suspension components are enclosed and inaccessible to

the rider.

K. PUSH HANDLES

1. Push handles provide secure points for an attendant to propel and control the

chair.This helps to prevent a fall or tip-over.

2. Check to make sure push handle grips will not rotate or slip off.

L. REAR WHEEL LOCKS (OPTIONAL)

If you request them, we will install rear wheel locks at Sunrise.

1. Rear wheel locks are not designed to slow or stop a moving wheelchair.

Never apply them when your chair is moving. Doing so may cause you to

veer out of control.

•

Use wheel locks only to keep the rear wheels from rolling when your

chair is at a complete stop.

2. Low pressure in a rear tire may cause the wheel lock on that side to slip and

may allow the wheel to turn when you do not expect it.

3. Make sure lock arms embed in tires at least 3/8 inch when locked. If you fail

to do so, the locks may not work.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I I I . T I P S F O R A T T E N D A N T S

I X . S E T - U P , A D J U S T M E N T

U S E

NOTES

1. Work Surface For Set-Up:

Use a flat surface, such as a table, to assemble, adjust and check your chair.

This makes the steps easier and helps ensure a correct set-up.

2. Fasteners:

1. Persons who help a rider do one of the following tasks should review and heed the

warnings “Notice to Attendants” and all warnings in this Manual for that task.

2. The “Tips” that follow are suggestions only. Be aware that you will need to learn

safe methods best suited to the rider and to your abilities. Consult your health

care professional for instructions.

•

Many of the screws and bolts on this chair are special high-strength fasteners

and may have special coatings.

Many nuts are of the Nylock type.They have a plastic insert to help

prevent loosening.

A. TO CLIMB A CURB OR SINGLE STEP

Only use screws, bolts and nuts provided by Sunrise.

The following is one way to safely help a rider climb a curb or single step

going forward:

1. Stay behind the chair.

2. Face the curb and tilt the chair up on the rear wheels so that the front casters

clear the curb or step.

3. Move forward, placing the front casters on the upper level as soon as you are

sure they are past the edge.

1. Use of improper fasteners may cause the chair to fail.

2. Over- or under-tightened fasteners may fail or cause damage to chair parts.

3. If bolts or screws become loose,tighten them as soon as you can. Loose bolts or

screws can cause damage to other chair parts causing them to fail.

3. Washers & Spacers:

4. Continue forward until the rear wheels contact the face of the curb or step.

Lift and roll the rear wheels to the upper level.

•

Note the position of washers and spacers before disassembly.

To avoid damage to the frame, replace all washers and spacers when you

reassemble parts.

B. TO DESCEND A CURB OR SINGLE STEP

4. Torque Settings:

•

A torque setting is the optimal tightening for a particular fastener. Use a

torque wrench that measures inch-pounds to secure screws, nuts and bolts

on this chair.

The following is one way to safely help a rider descend a curb or single step

going backward:

•

Note: Unless otherwise noted, use a torque setting of 120 inch-pounds for all fasteners.

1. Stay at the rear of the chair.

2. Several feet before you reach the edge of the curb or step, turn the chair

around and pull it backward.

3. Proceed carefully. Look over your shoulder and carefully step back until you

are off the curb or stair and standing on the lower level.

4. Pull the chair toward you until the rear wheels reach the edge of the curb or

step.Then allow the rear wheels to slowly roll down onto the lower level.

5. When the rear wheels are safely on the lower level, tilt the chair back to its

balance point.This will lift the front casters off the curb or step.

6. Keep the chair in balance and take small steps backward. Be sure to look

where you are going.Turn the chair around and gently lower front casters

to the ground.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S E T U P , A D J U S T M E N T

U S E

I X . S E T - U P , A D J U S T M E N T

U S E

A. BATTERY REMOVAL

To remove the batteries for transporting

or servicing:

TOOLS YOU WILL NEED

1. BasicTool Kit:

To set-up, adjust and maintain your chair you will need the following tools:

1. Remove Battery Box

•

7/16" socket wrench

a) Turn both swedge latches up (fig1&2,A)

located on the rear of the battery box.

b) Slide the box lid rearward until it is

removed.

c) Disconnect Power harness (fig 3), by

pulling plug rearward.

1/2" box and open-end wrench

3/4" box and socket wrench

5/32" Allen wrench

3/16" Allen wrench

Phillips screwdriver #2

Custom axle wrench (or a 1/2" open-end wrench)

d) Grab handle (fig1, B) and pull entire

batter box away from chair.

You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you

need from a hardware store.

e) Disconnect each battery and remove

from batterybox as needed.

2. Battery Installation

2. Torque Wrench:

If you plan to adjust and maintain this chair yourself, Sunrise recommends that you

use a torque wrench.

See section XI. Batteries, D for instruc-

tions and wiring diagram.

Note:The wrench must measure inch-pounds.You can buy a torque wrench and proper

sockets from a hardware store.

CHECK-OUT

Be sure this chair performs to your chosen operational settings. If it does not,

turn the chair off immediately and reprogram with the Quickie QTRONIX

Programmer. If you do not own a Quickie QTRONIX Programmer have your

SUPPLIER reprogram your wheelchair as needed. Or, you can order a

Quickie QTRONIX Programming Pad for your own use, from your supplier.

Batteries may weigh up to 40 lbs. Care

must be taken to avoid injury when

lifting.

Pull plug

B. SWING-AWAY FOOTRESTS

1. Installation

Note: Repeat this procedure until the chair performs to your specifications

a) Place swing-away pivot pin (A) into

the locating hole (B) on top of the hang-

er mount with the footrest facing out-

ward from frame.

When properly set-up, this chair will operate smoothly. Check to see that all components

work properly. If you detect a problem, be sure to correct it before use.

b) Rotate the footrest inward until latch

plate locks (C) into place on locking

bolt.

2. Removal

a. To remove footrest, press quick-

release lever (E).

b. Rotate footrest outward and lift.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S E T - U P , A D J U S T M E N T

U S E

I X . S E T U P , A D J U S T M E N T

U S E

3. Height Adjustment

F. JOYSTICK SWING-AWAY

RETRACTABLE MOUNT

(OPTIONAL)

The joystick is mounted with a mechanism

which allows the control to be locked in a

forward or retracted position using magnets.

Adjustment

a. Remove both bolts (F) in the hanger

frame tube.

b. Reposition footrest height.

c. Re-tighten all bolts (F).

C. ELEVATING LEGREST (OPTIONAL)

1. Installation

To install or remove Elevating Legrest

(ELR) see instructions for Swing-away

Footrest installation page 29.

a. To retract joystick, push outward

on the inside of joystick.

b. Push joystick away from front of

armrest until it locks into retracted

position.

c. To return to forward position, push

joystick forward until it locks into

place.

2. Adjustment

a) To raise legrest, lift to desired position.

Legrest will automatically lock in place.

b) To lower legrest, while seated in chair,

first lift slightly then press release

lever (F) down and lower legrest to

desired position.

G. DUAL-POST HEIGHT-

ADJUSTABLE ARMRESTS

The dual-post flip-back armrest can be

used as either a flip-back armrest or a

removable armrest.

D. REMOTE JOYSTICK

INSTALLATION (OPTION)

1. To Connect

a. Line up small cylindrical connector

with its receptacle on the rear of the

joystick.

1. Installing Armrest

a. Insert front and rear posts

into armrest receivers.

b. Engage levers (A and B) to secure

armrest.

2. Set-up for Flip-back Operation

a. Disengage lever (A) so front post

is able to come free.

b. Armrest now has the ability to be

flipped back without removal.

3. Set-up for Removal

a. Disengage levers (A and B) so front

and rear posts are able to come

free.

b. Armrest can now be easily

removed for transferring.

4. Height-Adjustment (option)

a. Release the upper securing lever

(C).

b. Push in firmly.

2. To disconnect

Pull back on the retaining ring (H) of the

cylindrical connector until it disconnects from

the joystick box.

E. TO ADJUST THE HEIGHT OF

THE REMOTE JOYSTICK

a) Remove the two pan-head screws (A),

securing the angle bracket mount (B).

b) Remove the Joystick from the mount by

unfastening the two screws (C) on the

underside of the mount.

c) Position angle bracket mount such that

you achieve the desired joystick height.

Four positions are available by

b. Set at desired height

c. Return securing lever to locked

position.

d. Move armrest up or down to allow

armrest to snap into place.

relocating the mount either on the top

or bottom of the mounting bar (D)

and/or by rotation of the angle

bracket mount.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S E T - U P , A D J U S T M E N T

U S E

I X . S E T U P , A D J U S T M E N T

U S E

H. HEIGHT-ADJUSTABLE

ARMRESTS (OPTIONAL)

(SEAT FRAME ONLY)

1. Installation

I. ARMREST WIDTH

ADJUSTMENT (CONTOUR &

HIGH BACK CONTOUR SEATS)

The width of the armrest mounts can be

adjusted.

a) Loosen screws (A).

b) Slide armrest mounting tubes to

desired location.

a. Slide the outer armpost into the

receiver mounted to the wheelchair

frame.

b. The armrest will automatically lock

into place.

2. Height Adjustment

c) Ensure that at least 1" of tubing lies

inward of the set screws.

d) Tighten screws (A).

a. Rotate release lever to second stop.

b. Slide armrest pad up or down to

desired height.

c. Return lever to locked position

against armpost.

Height-Adjustable

Armrest Key

J. ARMREST ANGLE

ADJUSTMENT (CONTOUR &

HIGH BACK CONTOUR SEATS)

a) Raise flip-back armrest.

b) Loosen bolt (B) and jam nut.

c) Adjust the height of the bolt to

desired height.

1. Outer armpost

2. Standard receiver

3. Release lever

4. Armrest pad

5. Transfer bar

6. Side panel

d. Push arm pad until upper armpost

locks firmly into place.

3. Removing Armrest

a. Rotate release lever to first stop and

remove the armrest.

4. Replacing Armrest

7. Outer armpost tension

adjustment set screws

8. Inner armpost

d) Tighten jam nut.

9. Receiver adjustment bolts

10.Release Lever

a. Slide armrest back into receiver.

b. Return release lever to locked posi-

tion against armpost.

5. Adjusting Armrest Receiver Fit

To tighten or loosen the fit of the outer arm-

post in the receiver:

a) Loosen the four bolts on the sides of

the receiver.

b) With the armrest in the receiver,

squeeze the receiver to achieve the

desired fit.

c) Tighten the four bolts.

6. Adjusting Inner Armpost Fit

a) Two set screws are installed in the

outer armpost.

b) Turn the set screws in or out until the

desired fit is achieved.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S E T U P , A D J U S T M E N T

U S E

I X . S E T - U P , A D J U S T M E N T

U S E

K. BACKREST

L. FOLDING BACKREST (SEAT

FRAME ONLY) (OPTIONAL)

Quickie S-525 wheelchairs are shipped

with backrest in folded position.

1. Upright Positioning

a) Lift backrest to upright position so

that latches (A) lock into place.

b) Backrest is ready for use.

2. Folding Backrest

A backrest angle-adjustment is standard

on the Contour seat, the Highback

Contour seat, and the Seat Frame.

1. Seat Depth and Angle Adjustment

on Seat Frame

a) Remove the front securing bolt (C) on

the side of the backrest hinge plate.

b) Loosen the lower rear bolt (D)

c) Set at desired angle.There are four

holes (in 4º increments) to choose from.

d) Reinstall the front bolt (C) and

tighten both bolts securely.

a) Lift and turn backrest latch handles

(B) outward.

b) Fold backrest forward.

2. Seat Depth and Angle Adjustment

on the Contour Seat

CAUTION: Backrest latches must

be locked into place before operating

wheelchair.

a) The contour seat is shipped with a

seat-to-back angle of 100º and a back

height of 18"

b) To increase the seat-to-back angle,

adjust stop bolt (E) to desired loca-

tion. Do the same for the other hinge.

c) To decrease the back height, remove hinge

bolt from hole (F) and replace bolt in hole

(G). Do the same for the other hinge.

Note: Adjusting the back height will change

the seat-to-back angle. Follow instructions to

adjust the seat-to-back angle accordingly.

Note: Adjustment on both sides of the wheel-

chair must be equal.

M.SEAT DEPTH (SEAT FRAME

AND CONTOUR SEATS ONLY)

The seat depth can be adjusted in one

inch increments.

1. Seat Frame Depth Adjustment

a) To adjust, remove the two bolts (A)

from each side of the backrest pivot

plate.

b) Reposition the backrest to the desired

position.

c) Replace and retighten bolts on each

side of the backrest pivot plate.

2. Contour Seat Depth Adjustment

a) Remove bolts (B) on the seat hingeplate.

b) Adjust the set back to desired position.

c) Refasten bolts (B) in appropriate loca-

tion.

3. Adjustment for the Highback

Contour Seat

a) Pull lever (H) upwards.

b) Lean back to desired position.

c) Release lever (H).

CAUTION:Backrest latches must be

locked into place before operating

wheelchair.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S E T - U P , A D J U S T M E N T

U S E

I X . S E T - U P , A D J U S T M E N T

U S E

N.PARAPAK SEAT SLING

(SEAT FRAME ONLY)

Q. CHECK-OUT

Once the wheelchair is assembled and adjusted, it should roll smoothly

and easily.All accessories should also perform smoothly.

The seat sling tension can be adjusted

through use of theVELCRO retaining

material beneath the seat.

1. Adjustment

After the wheelchair has been set up be sure the chair performs to your speci-

fied operational settings (see pages 38-42). If the chair does not perform to spec-

ifications, turn the wheelchair OFF immediately and reprogram operational speci-

fications using the QTRONIX Programming Pad.

a) Remove the screws retaining the left

side seat sling.

b) ReadjustVELCRO style material to

increase the tension in the seat sling.

c) Replace screws and tighten.

Important Note: If there is any difficulty in re-

attaching the screws, try using a probe to help

line up the holes.

Repeat this procedure until the wheelchair performs to specifications

before attempting active use of the wheelchair.

If you have any problems, follow these procedures:

1. Review the set-up and check-out section and operating guide to

make sure chair was properly prepared.

2. If your problem persists, contact your authorized supplier. If you still

have a problem after contacting your authorized supplier, contact

Sunrise customer service. See the introduction page for details on

how to contact your authorized supplier or Sunrise customer service.

O. SEAT HEIGHT AND ANGLE

ADJUSTMENT

Adjusting the seat height can be done both at

the front and at the rear of the seat. Seat angle

can also be varied through front and rear seat

height adjustment.

1. Rear Seat Height Adjustment

a) Use positioning holes (A & B) and

receiver notch (C).

2. Front Seat Height Adjustment

a) Use positioning holes (I, II, i, ii) and

hole set (1).

P. WHEEL LOCKS

Wheel locks are installed by Sunrise when

requested on the Quickie S-525

1. Mounting

The wheel lock mounts to the S-525

frame. Use a torque setting of 100

in./lbs when adjusting wheel locks.

a) Loosen bolt (D).

b) Slide mounting bracket toward rear wheel

until clamp embeds into tire to prevent

wheel movement when in locked position.

c) Tighten screw.

Note: Brake shown in rear position.

Hole F is used on standard position

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X . O P E R A T I N G G U I D E

A. PERFORMANCE CONTROL SETTINGS

1. It is vital to match performance control settings to your level of function and

ability.

2. Consult your health care professional and your supplier to select the best

control settings for you.

3. Check and adjust the settings every six to twelve months (or more often, if needed).

4. Adjust the control settings immediately if you notice any change in

your ability to:

2. To ProgramYour Chair:

a. Turn off power to the chair.

b. Insert QTRONIX Programmer plug (A)

into the charger/programmer socket

(B) on the front of the joystick.

c. Turn on power to the chair; program

as needed.

d. Remove plug and cycle ON/OFF

switch to drive chair.

Note: Review the QTRONIX Programmer

Owner’s Manual for more details on how to

program your chair.

•

Control the joystick.

Hold your torso erect.

Avoid running into objects.

5. Control Settings are adjusted through the use of the QTRONIX Programmer.

See your supplier if you do not own a QTRONIX Programmer.

Note: Program settings that are not matched

for the capabilities of the rider can result in

serious injury. Do not alter settings without the

advice of your health care professional.

B. QTRONIX PROGRAMMING PAD (OPTIONAL)

Program settings beyond the ability of the rider can result in serious injury. Consult

your health care advisor before you alter settings.

C. THERMAL ROLL-BACK

Your chair has a thermal roll back circuit.

This protects the controller from damage

due to overheating. In extreme conditions

(such as repetitive hill climbing) the circuit

will decrease the power to your motors.

This allows the chair to operate at a

reduced speed.When the controller cools,

the chair will return to normal speed.

1. Notes:

The QTRONIX Programmer lets

you adjust the performance

control settings of the S-525.

You can customize a program

for yourself or select the stan-

dard program.

D. CIRCUIT BREAKERS

1. Notes:

•

acceleration rate

deceleration rate

turn acceleration

turn deceleration

forward speed (max & min)

reverse speed (max & min)

turn speed (max & min)

steer correct

Your Quickie S-525 has a battery box with

a circuit breaker.

•

In the unlikely event of a short circuit

or heavy overload, all power to your

chair will be shut off.

To reset your chair, depress the circuit

breaker button (B) is on the front

right side of the battery box. A few

minutes wait is required before the

circuit breaker will reset.

With a remote system

you can also adjust:

•

4-axis joystick throw

sleep timer

read timer

2. Repeated Shutdown:

If the chair continues to shut down

after resetting, have it serviced by

a supplier.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X . O P E R A T I N G G U I D E

F. REMOTE JOYSTICK ASSEMBLY

(OPTIONAL)

E. INTEGRAL JOYSTICK

The standard integral joystick controls the

chair’s performance. It consists of the follow-

ing parts:

1. Speed Control or Drive Mode

Selection Buttons (A and B)

To decrease the speed level depress button A.

Or, when 1- 5 Drive modes are programmed,

depress button A to activate lower drive

mode(s).

To increase speed level, depress button B. Or,

when 1- 5 Drive modes are programmed,

depress button B to activate higher drive

mode(s).

The remote joystick connects to a controller,

which controls the chair’s performance.The

joystick assembly consists of the following

parts:

1. Speed Control Knob (D)

Use the speed control knob to adjust the max-

imum speed of your chair.Turn it counter-

clockwise to reduce speed; turn it clockwise to

increase speed.

2. Battery Charge Indicator (B)

•

Green lights indicate that batteries are

fully charged.

Yellow lights indicate that batteries need

recharging.

When the lights stay in the red band, the

batteries must be recharged.

Integral Joystick

Remote Joystick (Optional)

Speed level active, or Drive Mode selected, is

indicated on display (C) by a series of five

lights. One light indicates slowest level/mode

currently active, while five lights indicates high-

est level/mode currently active.

3. On/Off Mode switch (A)

The on/off mode switch is located on the rear face of the joystick housing. It is a

toggle switch.Turning the chair on or off, is accomplished by pressing the switch

downward.The switch will automatically return to the center point.Alternate

locations exist for this switch. Please see your supplier in the event that you wish

to relocate or re-orient this switch.

4. Mode Switch (A)

The on/off mode switch allows you to select from 5 (five) different programmable

drive profiles or actuator mode sets.

2. Battery Charge Indicator (D)

•

Green lights indicate that batteries are fully charged.

Yellow lights indicate that batteries need recharging.

When the lights stay in the red band, the batteries must be recharged.

3. On/Off Button (E)

Turning the chair on or off is accomplished by depressing button E.

4. Horn (F)

•

Push up the on/off mode select toggle switch to index among the five drive

and actuator modes.The selected mode indicator will flash.

Push joystick either left or right to select one of the five drive profiles.To

select the actuator modes, push up on the mode select switch twice.

The drive profiles are indicated by the mode indicators (G) and the actua-

tors are indicated by the four actuator lights (H).

To exit drive or actuator mode select, simply push the on/off/mode toggle

up one or more times until the indicator no longer flashes, or push the joy-

stick forward or reverse to begin driving.

5. Joystick (G)

The joystick controls the direction and speed of your chair.Turn the chair on and

move the joystick in the direction you want to go.

•

Moving the joystick from the neutral (center) position disengages the

motor locks, allowing the chair to move.

The chair will move faster the more you move the joystick away from neutral.

Note: If your speed becomes hard to manage, release the Joystick and the chair will come

to a complete stop.

5. Joystick (E)

•

When you release the joystick it will return to neutral; the chair will slow

to a stop and the motor locks will reengage.

We recommend that you switch the chair off if you stop for any length of

time.This will conserve battery power.

The joystick controls the direction and speed of your chair.Turn the chair on and

move the joystick in the direction you want to go.

•

Moving the joystick from the neutral (center) position disengages the

motor locks, allowing the chair to move.

The chair will move faster the more you move the joystick away from neu-

tral.

Note: Once the chair stops, switching the chair off will not affect the motor locks.

6. Joystick Boot (H)

Make sure the boot is not torn or cracked (this could allow debris, water or

moisture to enter). If the boot is torn or cracked, replace it as soon as you can.

Note: If your speed becomes hard to manage, release the Joystick and the chair will come

to a complete stop.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X . O P E R A T I N G G U I D E

X I . B A T T E R I E S

A. INTRODUCTION

1. Notes:

•

When you release the joystick it will return to neutral; the chair will slow

to a stop and the motor locks will reengage.

We recommend that you switch the chair off if you stop for any length of

time.This will conserve battery power.

•

Batteries supply the power for your chair.They contain a finite amount of

energy and have limits on how long they can store and supply energy.

You can charge batteries only a certain number of times before they will

fail and no longer hold a charge.

Note: Once the chair stops, switching the chair off will not affect the motor locks.

6. Joystick Boot (F)

Make sure the boot is not torn or cracked (this could allow debris, water or

moisture to enter). If the boot is torn or cracked, replace it as soon as you can.

7. Remote Switch Jacks (optional– not shown)

Two 1/8" switch jacks are optional to provide remote switch control of the on/off

power function and the mode select function. Any of the single switches offered

by Sunrise Medical can be used to connect to either or both of these jacks

(except the single zero touch switch).

For answers to questions about batteries, consult your supplier.

2. Use Proper Batteries:

Your chair operates on two 12 volt batteries.

•

They should be 22 NF or U1 size with a minimum of 30 ampere hour rating.

Only deep cycle sealed case construction batteries should be used in

this device.

•

When you buy a replacement, insist on a deep cycle sealed case type.

Do not use a car starter battery.

3. Breaking In:

•

A battery requires “breaking-in” for the first 6 to 12 charges. It will not

accept a full charge for this period.

It is best to limit the length of your trips until you break the batteries in

and you know the range of your chair.

1. Never use the ON/OFF switch to stop your chair except in an

emergency.

This will result in an abrupt stop, and may cause you to fall.

2. To slow or stop your chair, return the joystick to neutral.

•

4. Discharged Batteries:

•

Never allow a battery to completely discharge. If you operate your wheelchair

until it has almost stopped, you will greatly reduce the life of your batteries.

Never let a battery sit in a discharged condition. Give unused or stored

batteries a full charge once per month.

Always fully charge the batteries. Avoid “topping Off” with

frequent charges.

G. MOTOR LOCKS

Disconnect the motor locks when you need to manually push the chair. (For

example, in an emergency, or if batteries fail).

1. Do not disengage motor locks unless power to the chair is off.

2. Be aware that the chair will not have brakes in the free-wheel position.

3. Make sure that the person pushing the chair has full control when motor locks

are disengaged.

Never connect a life support or auxiliary device to a wheelchair battery.The electrical

system may fail, and result in severe injury to or death of rider.

1. To Disengage Motor Locks

B. BATTERY CHARGER

Push Lever (A) Down to the free-wheel

position.

2. Engage Motor Locks

Push the lever (A) up into the drive

position.

A battery charger produces a direct current (DC).When applied to a

discharged battery, this reverses the chemical reaction that led to its discharge.

1. Charge Rate. How fast a battery will charge depends on:

•

Its electrical capacity; state of charge; electrolyte temperature, and;

internal condition.

•

The DC output of the charger. (The charge rate will vary if the alternating

current (AC) supply is higher or lower than 110 volts).

2. Caution —To Avoid Damage to the Charger:

•

Never place the charger on top of a battery during charging. (Gases from

the battery can damage the charger and may lead to an explosion or fire).

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I . B A T T E R I E S

•

Never place a battery on top of the charger.

Never expose charger to rain or snow.

Never unplug charger by pulling on the electrical cord.This will damage

the cord.

Never open a charger or attempt to repair it yourself. Return charger to

Sunrise or have repairs made only by a qualified person.

Keep cord out of the way, where it will not be stepped on, tripped over,

or damaged.

Each battery weighs up to 40 pounds. Lifting batteries may cause back strain. If

you fail to heed these warnings severe injury may occur to you.

•

1. Attach battery harness to posts. Connect the red lead to the positive terminal

and the black lead to the negative terminal. Do this for each battery/combina-

tion.

3. Caution —To Avoid Damage to the Battery:

2. Tighten all terminal fasteners using two wrenches.

3. Place the batteries in the battery box.

4. Connect the power harness connector to the battery harness connector.

5. Place the lid on the box. Slide box into position in the rear of the chair.Turn

both swedge latches down. (see illustration on pg. 29)

•

Make sure you use the correct setting for sealed (gel) batteries (located on

the off-board charger).

•

Never charge a frozen battery.A fully charged battery will rarely freeze,

but the fluid in a discharged battery can freeze at 16 degrees Fahrenheit

(minus 9 degrees Centigrade). If you suspect a battery is frozen, thaw it

before charging.

Never make direct contact across both battery terminals, as an explosion may occur.

A spark may result in an explosion and/or fire resulting in severe injury or death.

Lead acid batteries generate explosive gas while charging. Completely read and follow

all warnings about the batteries in this user instruction manual and any labels applied

to the product. Failure to do so could result in fire, explosion, injury and/or death.

C. ACID BURNS (UNSEALED WET CELL BATTERIES)

Acid in batteries is corrosive. It can cause serious burns to the eyes and skin

and can damage floors, furniture, clothing and your wheelchair.

1. Use extreme care not to spill acid when you handle batteries.

Keep batteries upright.

2. Avoid contact of acid with bare skin or clothing.

3. Always wear rubber gloves and safety glasses when you handle batteries.

4. If acid contacts your skin or clothing, wash immediately with soap and water.

5. If acid contacts your eyes, immediately flood eyes with cold running water for at

least 15 minutes. Seek medical attention immediately.

D. CONNECTING BATTERIES IN BATTERY BOX

E. CHARGING BATTERIES

1. Each battery weighs up to 40 lbs.Take care to avoid injury when lifting.

2. Keep batteries upright.Take care not to spill acid (wet cell batteries).

3. Always wear rubber gloves and safety glasses when you handle batteries.

4. Before working around batteries, remove all metal personal effects, such as

necklaces, rings, watches, pins, and other metal jewelry that might contact

battery terminal and cause a short.

To avoid the risk of severe injury or death from electrical shock, fire or explosion

while charging:

1. Never connect charger to a 240 volt source.The mains input voltage is 110 volts.

2. Never touch the charger after it is connected to an electrical outlet.This may cause

electrical shock.

•

Never connect or disconnect charger from battery while there is power to

the charger.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I . B A T T E R I E S

X I I . M A I N T E N A N C E

3. Never use an extension cord. Use of an improper cord could damage the charger, or

cause a fire or electrical shock.

A. NOTES

1. Proper maintenance will improve performance and extend the useful life

of your chair.

2. Clean your chair regularly.This will help you find loose or worn parts and will

make your chair easier to use.

3. To protect your investment, have all major service and repair work done by

your supplier.

4. A battery emits explosive hydrogen gas during charging.To reduce the risk of fire

or explosion:

•

Make sure area is well vented. Never charge battery in a closed-in area.

Never smoke or allow a spark, flame or high heat near battery during changing.

Never allow metal tools or chair parts to make direct contact across both

terminals.

5. Never look directly into cells when charging battery.

1. Your chair needs regular maintenance for peak performance and to avoid

injury from chair failure, damage or premature wear.

Always:

2. Inspect and maintain this chair strictly per the “Maintenance Chart” (p. 51).

3. If you detect a problem, make sure to service or repair the chair before use.

4. At least once a year, have a complete safety check and service of your chair per-

formed by a supplier.

1. Use the charger that comes with your wheelchair. Read and follow all

instructions and warnings.

2. Make sure room is well ventilated.

3. Turn off all power to your chair.

4. Connect and disconnect battery cables with caution. Only connect the charger

to the power supply after the charger has been connected to the chair.

5. Make sure to allow enough time to fully charge batteries.

NOTE: Batteries should never be left for long periods in the discharged state. Unused

or stored batteries should be given a charge once per month.

6. Charge batteries by engaging the battery charger connector (A) to the

charger/programming port (B) located on the joystick.

B. CLEANING

1. Paint Finish:

•

Clean the paint finish with mild soapy water monthly.

Protect the paint with a coat of non-abrasive auto wax every three months.

2. Motors:

•

Clean around motor area weekly with a slightly damp (not wet) cloth.

Wipe off or blow away any fluff, dust, or dirt on or around the motors.

Note: You do not need to grease or oil the chair.

3. Upholstery:

•

Hand-wash only as needed. Machine washing may damage fabric.

Drip-dry only. Heat from a dryer may damage fabric.

Note: Washing the fabric may decrease fire retardant properties.

C. STORAGE TIPS

1. Store your chair in a clean, dry area. If you fail to do so, parts may rust or corrode.

2. Before using your chair, make sure it is in proper working order. Inspect and

service all items on the “Maintenance Chart” (See p. 51)

3. If you store this chair for more than three months, have it inspected by a

supplier before use.

Integral Joystick

Remote Joystick

F. DISPOSING OF BATTERIES

1. All batteries once they have reached the end of their useful life are deemed

to be hazardous waste.

2. For further information on handling and recycling contact your local

recycling authority.

3. Always dispose of product through a recognized agent.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I I . M A I N T E N A N C E

E. PNEUMATIC TIRES

D. BATTERY MAINTENANCE

1. Do not use this chair if any of the tires are

under- or over-inflated.

1. To prevent an acid spill, always keep batteries upright (wet cell batteries).

2. Never smoke or hold an open flame near batteries.

2. Low pressure in a tire may cause the chair

to veer to one side and result in loss of

control.

3. Always wear rubber gloves and safety glasses when you handle batteries.

1. Maintenance Schedule:

3. An over-inflated tire may burst.

4. Never use a gas station pump to inflate a

tire. Such pumps provide air at high volume,

and may cause tire to burst.

This varies for different types of batteries.Always follow the instructions

supplied with your batteries.

Note: Always wear rubber gloves and safety glasses when you handle or service batteries.

2. Adding Water: (Wet Cells Only)

1. Check for signs of wear and correct

air pressure in pneumatic tires weekly.

2. For best performance, inflate tires to

the same pressure level, as shown on

the tire sidewall:

•

Wet-type lead acid batteries need periodic replacement of water.

Note: use distilled water only.

•

Check the battery fluid level about once a week.When you remove the

stoppers (on top of the battery) there should be one-eighth to one-quarter

of an inch of fluid above the internal plates. Do not overfill.

• 8" pneumatic casters - 30 to 40 psi

• 12" pneumatic drive wheels - 35 to

45 psi

3. Corrosion:

Check battery terminals often for corrosion.

a. If corrosion is present, use a wire brush to clean the terminals.

Note: Always wear safety glasses and rubber gloves.

b. Use baking soda to neutralize acid.

c. Use petroleum jelly to re-grease the terminals after connecting cable to

battery. (Completely cover the terminal nut and bolt, cable clip and any

exposed cable with jelly).

3. Caution:

To prevent tire damage:

• Use a hand pump (or a low vol-

ume air pump) to inflate tires.

• Use a tire gauge to check pressure.

F. TO REPAIR OR REPLACE A TIRE

4. For AnswersTo Questions: Contact your supplier.

Residual air pressure in tires can

cause severe injury. Make sure you

release all air in tire before attempt-

ing to service or repair tires.

1. 8" & 9" (200 & 250mm) Caster

Wheels:

a. Release all air from tire.

b. Remove caster wheel from fork using

a 1/2" wrench.

c. Make sure there is no residual air in

tire before you remove bolts that hold

the two rim halves together.

d. Remove four bolts from rim using a #3

phillips screwdriver. Separate two

halves of rim.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I I . M A I N T E N A N C E

e. Repair or replace inner tube.

I. MAINTENANCE CHART

f. Reassemble the caster wheel; make sure the bearing spacer is in place and

all four bolts are tightened to a torque of 60 in.-lbs. (6.8 N.m).

g. Mount caster wheel onto fork. Install washers correctly tighten bolt to 240

in.-lbs. (27 N.m).

You should check the items on this chart at the indicated intervals. If any of

the items are loose, worn, bent or distorted, immediately have them checked

and/or repaired by your authorized Sunrise supplier. Frequent maintenance

and servicing will improve performance, extend wheelchair life, and help pre-

vent injuries.

h. Inflate tire to proper pressure level.

2. 12" (310 mm) Drive Wheels:

a. Elevate and securely support chair so that wheel is off the ground.

Release all air from tire.

CHECK...

b. Remove four (4) lug nuts (A) from rim using a socket wrench.

c. Make sure all air has been removed from tire. Remove the four bolts inside

the rim. Separate two halves of rim.

Charge Batteries

Check tires for proper inflation level

Check batteries for proper electrolyte level (wet cell only)

d. Repair or replace inner tube. Reassemble the wheel.

Use a torque setting of 120 in.-lbs. (13.5 N.m) to re-tighten bolts.

e. Inflate tire to proper pressure level (listed on tire sidewall).

Check plugs and connectors for proper connections

Check all moving parts for wear

G. MOTOR BRUSHES

Inspect all nuts, bolts and fasteners for looseness or wear

Check the motor brushes every four (4) months for wear.The brushes should

be clean and shiny. Replace worn or blackened brushes.

Inspect upholstery for wear

H. ORDERING PARTS

When you order parts, provide the following:

1. Model of chair

Remove and inspect motor brushes

Servicing by authorized Supplier

2. Serial number of chair

3. Left hand or right hand control

4. Part number, description and quantity of parts you need.

5. State reason for replacement.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I I I . W I R I N G D I A G R A M S

Wiring Diagram Detail (Remote Joystick)

Wiring Diagram Detail (Integrated Control System)

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

X V . S U N R I S E L I M I T E D W A R R A N T Y

1. FOR LIFE

We warrant the main frame of this wheelchair against defects in materials and

workmanship for the lifetime use of the first consumer purchaser.

2.ADDITIONAL WARRANTY

We warrant Sunrise-made components of this wheelchair against defects in

materials and workmanship as follows:

a. Main electronic controller—For two (2) years from the date of first con-

sumer purchase.

b. Motors, gear boxes and remote joystick—For one (1) year from the date

of first consumer purchase.

c. All other original components (such as wheels, upholstery, plastic, rubber

parts and painted surfaces)—For three (3) months from the date of first

consumer purchase.

3. LIMITATIONS

a. We do not warrant damage due to:

• Neglect, misuse, or improper installation or repair.

• Use of parts or changes not authorized by Sunrise.

• Exceeding the weight limit of 250 pounds for the standard system, 350 lbs

for the heavy duty system.

b. This warranty is void if the original chair serial number tag is removed or

altered.

c. This warranty applies in the USA only. Check with your supplier to find

out if international warranties apply.

4.WHAT WE WILL DO

Our sole liability is to repair or replace covered parts.This is your only

remedy for consequential damages.

5.WHATYOU MUST DO

a. Return the warranty card.

b. Obtain from us, while this warranty is in effect, prior approval for return or

repair covered parts.

c. Return the wheelchair or part(s), freight pre-paid, to Sunrise Mobility Products

Division at: 2842 Business Park Ave., Fresno, CA 93727-1328.

d. Pay the cost of labor to install or repair parts.

6. NOTICETO CONSUMER

There are no other express warranties.To the extent permitted by law, any

implied warranty (including a warranty of merchantability or fitness for a par-

ticular purpose) is limited to:

a. One (1) year from the first consumer purchase, and;

b. Repair or replacement of the defective part only.

This warranty gives you certain legal rights.You may also have other rights that

vary from state to state.

930486 Rev.A

Download from Www.Somanuals.com. All Manuals Search And Download.

Sunrise Medical

7477 East Dry Creek Parkway • Longmont, Colorado • 80503 USA

(800) 333-4000

In Canada (800) 263-3390

Manufactured under one or more of the following patents:

U.S. and European patents pending.

930486 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

Shark Vacuum Cleaner EP710 User Manual
Shindaiwa Edger 89307 User Manual
Sierra Wireless Network Router Overdrive User Manual
Silvercrest Waffle Iron SDW 1200 A1 User Manual
Sony CD Player CDX 2180 User Manual
Sony DVD VCR Combo RDR VX500 User Manual
Sony Projection Television KDS Z60XBR5 User Manual
Sony TV Receiver EBS SP35 User Manual
Superior Cell Phone Z258C User Manual
SUPER MICRO Computer Computer Hardware X9DRD iF User Manual