USER’S MANUAL
XB24-2502
DOT MATRIX PRINTERS
Download from Www.Somanuals.com. All Manuals Search And Download.
ZB152 80825140
About this manual
This manual describes how to set up, use, and care for the Star XB24-2502
printer. The following is a list of what you can expect to find in each chapter.
Chapter 1
Choosing a place for your printer, unpacking and setup,
ribbon cassette installation, loading paper, connecting to
your computer
Chapter 2
Chapter 3
How to use the control panel
How to use the printer’s Electronic DIP Switch (EDS)
Mode to set up the printer to match the needs of your
system and software
Chapter 4
Chapter 5
How to set up for printing with MS-DOS
Selecting the best type of paper, adjusting for paper
thickness, manual sheet feeding, clearing paper jams
Chapter 6
Optional accessories that are available for your printer
Appendix A How to deal with printing problems
Appendix B Specifications
Appendix C Interface information
Appendix D Character sets
Appendix E Printer control codes
Appendix F
Control panel operation guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Printer Setup ... 1
Choosing a place for the printer ... 1
Unpacking the printer ... 2
General guide ... 3
Installing the platen knob ... 4
Opening the front cover ... 4
Removing the front cover ... 5
Installing the ribbon cartridge ... 5
Removing the ribbon cartridge ... 7
Installing the paper guide ... 7
Adjusting the paper guide position ... 8
Connecting to a power outlet and turning power on and off ... 8
Loading fanfold paper ... 9
Printing on fanfold paper ... 12
Parking fanfold paper ... 13
Unparking fanfold paper ... 13
Using the tear-off function ... 13
Connecting to your computer ... 14
Chapter 2: Control Panel Operations ... 16
Switching between on-line and off-line ... 16
Selecting a font ... 17
Entering the Font Lock Mode ... 17
Setting the character pitch ... 18
Entering the Pitch Lock Mode ... 18
Line feed ... 19
Paper eject (cut-sheet paper) ... 19
Form feed (fanfold paper) ... 19
Parking fanfold paper ... 19
Micro feed ... 19
Setting the top of form position ... 20
Tear-off function (fanfold paper) ... 20
Selecting the Quiet Print Mode ... 20
Changing the auto load position ... 21
Saving a macro ... 22
Clearing the printer’s buffer ... 22
Initializing the printer ... 23
Entering the Multi-part Mode ... 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Using the EDS Mode ... 24
About EDS Mode settings ... 24
Entering the EDS Mode ... 24
Selecting a bank ... 25
Selecting a switch ... 25
Changing a switch setting ... 25
Printing the current switch settings ... 26
Checking the settings of switches in a bank ... 26
Exiting the EDS Mode ... 26
EDS Mode Settings ... 27
Chapter 4: Using the Printer with MS-DOS ... 37
Setting up for printing with MS-DOS ... 37
Chapter 5: Paper Handling ... 38
Selecting paper types ... 38
Adjusting for paper thickness ... 39
Automatic fanfold feeding ... 40
Manual sheet feeding ... 40
Clearing paper jams ... 41
Chapter 6: Optional Accessories ... 42
Automatic Sheet Feeder (SF-15DM2) ... 42
Pull Tractor Unit (PT-15XM) ... 43
Serial Interface Cartridge (IS-8XL) ... 43
Buffered Parallel Interface Cartridge (IP-128XL) ... 44
Serial-to-Parallel Converter (SPC-8K) ... 44
Appendix A: Troubleshooting ... 46
Appendix B: Specifications ... 53
Appendix C: Interface Pin Outs ... 56
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Character Sets ... 57
Appendix E: Printer Control Codes ... 69
Appendix F: Control Panel Operation Guide ... 79
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Chapter 1: Printer Setup
This chapter contains important information on setting up your printer. Be sure
to read this chapter carefully before using the printer for the first time. In this
chapter you will learn about:
❏ Choosing a place for the printer
❏ Unpacking and setting up the printer
❏ Installing the platen knob
❏ Installing the ribbon cassette
❏ Loading paper
❏ Connecting to your computer
Choosing a place for the printer
Before actually unpacking the printer, you should take a few minutes to think
about where you plan to use it. Remember the following points when doing this.
✓ Choose a firm, level surface where the printer will not be exposed to
vibration.
✓ The power outlet you plan to connect to for power should be nearby and
unobstructed.
✓ Make sure that the printer is close enough to your computer for you to
connect the two with your printer cable.
✓ Allow six inches (15 centimeters) of free space on either side of the printer.
If you are going to use fanfold paper, make sure that there is adequate space
for paper behind the printer.
✓ Make sure that the printer is not exposed to direct sunlight.
✓ Make sure that the printer is well away from heaters.
✓ Make sure that the surrounding area is clean, dry, and free of dust.
✓ Make sure that the printer is connected to a reliable power outlet. It should
not be on the same electric circuit as copiers, refrigerators, or other
appliances that cause power spikes.
✓ Use a power outlet that matches the power rating noted on the label affixed
to the bottom of your printer.
✓ Make sure that the room where you are using the printer is not too humid.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Printer Setup
Unpacking the printer
Check to make sure that the carton contains each of the items shown in the
following illustration.
If anything is missing, contact the store where you bought the printer and ask
them to supply the missing part. Note that it is a good idea to keep the original
box and all the packing materials just in case you need to pack the printer up
again and send it somewhere at a later date.
A serial-to-parallel interface converter (SPC-8K), a parallel interface unit (IP-
128XL), a serial interface unit (IS-8XL), a pull tractor (PT-15XM), and an
Automatic Sheet Feeder (SF-15DM2) are also available as options. Consult
your dealer for details.
Important!
There are several versions of this printer designed for different voltages. It is
not possible to change the voltage of a printer. If the voltage shown on the label
on the bottom of your printer does not match the voltage for your area, contact
your dealer immediately.
Download from Www.Somanuals.com. All Manuals Search And Download.
General guide
3
General guide
The following illustrations show the major components of the your printer.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Printer Setup
Installing the platen knob
You can find the platen knob in the box of items that contains this manual.
❏ Install the knob on the shaft located inside the large hole on the right side of
the printer. Make sure that the two metal pins on the platen shaft fit into the
slots inside the knob’s spindle. Press the knob carefully but firmly into
place as far as it will go.
Opening the front cover
❏ Lift up on the front cover and swing it open until it stops.
❏ To close the front cover, simply lower it back into place.
Caution!
The tear assist edge is rather sharp. Take care to avoid injuring your hands.
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the front cover
5
Removing the front cover
Normally, you should leave the front cover connected to the printer, using the
procedure described above to open and close it as required. You can also
completely remove the front cover using the steps described below.
❏ Lift up on the front cover and swing it up until it is a little more than half
way open.
❏ Carefully pull the front cover towards the back of the printer, moving it
slightly up and down to work it free from the printer body.
❏ To replace the front cover, reverse the two steps described above.
Installing the ribbon cartridge
❏ Make sure that the printer is unplugged from its power outlet.
Caution!
Never touch the print head while the printer is turned on. Doing so can damage
the printer. If you have just finished printing, let the print head cool for a few
minutes before you touch it.
❏ Open the front cover of the printer.
❏ Remove the ribbon cartridge from its package.
❏ Rotate the knob on the ribbon cartridge clockwise to take up any slack in
the ribbon.
❏ Carefully place the cartridge onto the cartridge holder making sure that the
spindle of the holder fits into the socket on the bottom of the cartridge. Also
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Printer Setup
make sure that the side tabs fit into the grooves on the sides of the cartridge
holder.
❏ While guiding the ribbon between the print head and print head shield,
press down gently on the cartridge until the side tabs snap securely into
place.
❏ Rotate the knob on the cartridge again to take up any slack.
❏ Close the front cover of the printer.
Important!
Printing that is poor quality or too light is almost always due to a ribbon that is
simply worn out or “used up.” If you experience problems with print quality,
check the conditio of the ribbon. If the black part looks gray and well-worn,
replace the ribbon with a new one.
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the ribbon cartridge
7
Removing the ribbon cartridge
Use the following procedure to remove the ribbon cartridge from the printer
when you want to replace it with a new one.
❏ Make sure that the printer is unplugged from its power outlet.
Caution!
Never touch the print head while the printer is turned on. Doing so can damage
the printer. If you have just finished printing, let the print head cool for a few
minutes before you touch it.
❏ Open the front cover of the printer.
❏ Using your thumb and forefinger to squeeze the two tabs on the ribbon
cartridge towards the center, carefully remove the cartridge from the holder.
❏ Use the procedure under “Installing the ribbon cartridge” on page 5 to
install a new cartridge.
Installing the paper guide
You can find the platen knob in the box of items that contains this manual.
Insert the two pointed tabs on the bottom of the paper guide straight down into
the holes provided on the top back of the printer, and then lay the paper guide
down so the tabs inside the holes slip into the grooves on the paper guide tabs.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Printer Setup
❏ To remove the paper guide from the printer, stand it up while gently pulling
it towards the front of the printer, Next carefully lift the paper guide straight
up.
Adjusting the paper guide position
❏ The paper guide has two positions: raised and lowered. You can use either
position for printing.
❏ To lower the paper guide, stand it up while gently pressing towards the
back of the printer. Next, lift up slightly until the paper guide stops and then
lay it down towards the back of the printer.
❏ To raise the paper guide, slowly stand it up until you feel it slide into a
locked position.
Connecting to a power outlet and turning power on and off
❏ Plug the power cord of the printer into a standard power outlet whose
voltage matches the power rating noted on the label affixed to the bottom of
your printer.
Caution!
If the voltage marked on the bottom of your printer does not match the voltage
from the outlet you are using, do not plug in the power cord. Contact your
dealer for assistance.
❏ Set the switch on the front of the printer to ON to turn power on, and to
OFF to turn power off.
Important!
Whenever you turn off the power, wait for at least five seconds before turning it
back on. Otherwise you may damage the printer. We also recommend that you
unplug the printer from the power outlet whenever you do not plan to use it for
long periods. Because of the this, you should locate the printer so that the
power outlet it is plugged into is nearby and easy to access.
At this point you may want to perform a test of the printer to make sure it is
working properly. See “Testing the printer” on page 46 for details on how to
perform tests.
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading fanfold paper
9
Loading fanfold paper
This section tells you how to load fanfold paper. Note that you can also use cut-
sheet paper and multi-part form paper. For details on using other types of paper,
see “Paper Handling” on page 38 of this manual.
❏ Remove the paper guide from the printer.
❏ Position the stack of paper behind the printer.
❏ Make sure printer power is turned off.
❏ Set the release lever to the fanfold position.
❏ Grasping the two back corners of the printer with the palms of your hands,
lift up with your thumbs at the two thumb holds on either side of the rear
cover until it opens. Allow the rear over to swing open as far as it will go.
Important!
You can also completely remove the rear cover by lifting it straight up from the
printer while the cover is just past half way open.
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Printer Setup
❏ Pass the fanfold paper through the space between the printer case and the
rear cover, with the side you want to print on facing down.
❏ Unlock the two tractors by pulling up their gray levers, and slide the
tractors so they are aligned approximately with the holes on the sides of the
paper. Press the gray levers back down to lock the tractors into place.
❏ Slide the center paper support into position so that it is approximately
halfway between the two tractors.
❏ Open the covers of both tractors and insert the paper so the tractor pins fit.
❏ Close the tractor covers. At this point you can make final adjustments to the
paper position by releasing the gray levers and sliding the tractors left and
right. The paper should lie flat with no buckling or bulging (tractors too
close) or no stretching or undue pulling on the holes (tractors too far apart).
After making these adjustments, be sure that you re-lock the tractors by
pressing the gray levers back into their original positions.
❏ Close the rear cover and press down gently on it until it locks into place
with a click.
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading fanfold paper 11
❏ Install the paper guide so that it is standing up. In this position, the paper
guide keeps the printed paper separate from the unprinted paper.
❏ Turn on the printer.
The printer will beep a number of times if paper is not loaded properly. Also,
the control panel’s POWER indicator flashes whenever paper is not loaded.
❏ Press the SET/EJECT/PARK button to feed the paper to the starting
position.
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Printer Setup
Printing on fanfold paper
When printing on fanfold paper, take care not to print too close to the
perforations that separate each sheet. The following shows the recommended
print area for fanfold paper and cut-sheet paper.
Fanfold forms
Single sheets
Perforation
(*80 mm for Push Feed)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parking fanfold paper 13
Parking fanfold paper
It is not necessary to remove fanfold paper currently loaded in the printer in
order to print on cut-sheet paper. Instead, simply use the following procedure to
park the fanfold paper.
❏ Tear off the paper at a perforation so there is no more than half a page
sticking out of the front cover of the printer.
If necessary, you can press the control panel’s ON LINE button to put the
printer off-line. and then use the LINE FEED button to feed the paper until
a perforation is just past the front cover.
❏ Press the control panel’s ON LINE button to put the printer off-line.
❏ Press the control panel’s SET/EJECT/PARK button. The printer
automatically reverse feeds the fanfold paper until it is no longer in contact
with the platen, which is indicated by the printer beeping a number of
times. Also, the control panel’s POWER indicator starts to flash because
paper is not loaded.
❏ Move the release lever to the cut-sheet position.
❏ Change the paper guide to its upright position.
You can now load cut-sheet paper into the printer using the procedures
under “Manual sheet feeding” on page 40.
Unparking fanfold paper
After you are finished printing on cut-sheet paper, use the following procedure
to unpark fanfold paper and make it available for printing.
❏ Remove all cut-sheet paper from the printer.
❏ Change the paper guide position so it is laying down flat.
❏ Move the release lever to the fanfold position.
❏ Press the SET/EJECT/PARK button to feed the paper to the starting
position.
The printer automatically goes back on-line at this time.
Using the tear-off function
The following procedure makes it easy to tear off fanfold paper.
❏ Check to make sure that the printer is on-line.
❏ Press the FORM FEED button to perform the long tear-off operation, or
press the LINE FEED button to perform the short tear-off operation.
The long tear-off operation causes the paper to be fed automatically so the
tear assist edge of the printer cover is aligned with the paper’s next
perforation.
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Printer Setup
The short tear-off operation causes the paper to be fed automatically so the
tear assist edge of the printer cover is located just below the last line printed
on the paper.
❏ Pull the paper against the tear assist edge to tear it off.
Connecting to your computer
The computer sends data to the printer through a cable. This printer does not
come with a cable, so it is up to you to provide one. You will probably want to
use a standard parallel cable for connection, but note that you can also use an
optional serial-to-parallel interface converter (SPC-8K) or an optional interface
cartridge (IS-8XL or IP-128XL).
Important!
The following instructions apply to the Centronics parallel cable that is used
with an IBM-compatible personal computer. Note that they do not apply to all
types of computers and cables. If you are unsure about what type of cable you
should use to connect with your computer, consult your dealer.
For an IBM-compatible personal computer:
✓ Use a standard 36-pin Centronics parallel cable.
✓ The parallel cable should be no longer than six feet (two meters). Longer
cables can result in poor transfer of information.
Important!
Make sure that the printer and the computer are turned off before connecting
them.
❏ Plug one end of the parallel cable into the parallel port of your computer.
The parallel port should be labeled “Printer,” “Parallel,” “PRN,” “LPT1,”
or something similar.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to your computer 15
❏ Plug the other end of the parallel cable into the socket on the back of the
printer and secure it in place with the clips.
Note:
Consult your dealer for details on how to set up your computer when using the
optional SPC-8K serial-to-parallel interface converter, the IP-128XL parallel
interface unit or the IS-8XL serial interface unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Chapter 2: Control Panel Operations
The control panel gives you push-button control over the printer’s operations. It
includes indicator lights, which tell you the current status of the printer at a
glance.
A
B
C
SANSERIF
COURIER
PRESTIGE
ORATOR
D
E
F
ROMAN
LQ
1
2
3
10 CPI
12 CPI
15 CPI
4
5
6
COND
PROP
QUIET
POWER
ON LINE
DRAFT
HS-DRAFT
MICRO FEED
SET/EJECT
PARK
FONT
PITCH
FORM FEED
LINE FEED
EDS
BANK
SWITCH
STATUS
ON/OFF
PRINT
EXIT
This chapter describes control panel functions that can be performed while the
printer is turned on and either on-line or off-line. The buttons perform different
functions in the EDS and Dot Adjustment Modes. Functions of control panel
buttons in these modes are described in the relevant sections covering them.
Switching between on-line and off-line
❏ Press ON LINE to switch the printer between being on-line and off-line.
❏ When the printer is on-line, the ON LINE indicator is lit and the printer can
receive data from the computer. You should make sure that the printer is on-
line whenever you are trying to print.
❏ When the printer is in off-line, the ON LINE indicator goes out, which
means that the printer cannot receive any data.
❏ Note that you can also press ON LINE while a printing operation is in
progress to stop the printing.
Important!
Make sure that the on-line/off-line setting of the printer is correct before
performing a control panel operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a font 17
Selecting a font
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ Press FONT to change the font selection. An indicator lights to the left of
the name of the font that is currently selected.
Lit Indicator
Font
LQ + ROMAN
LQ + SANSERIF
LQ + COURIER
LQ + PRESTIGE
LQ + ORATOR
LQ
Roman
Sanserif
Courier
Prestige
Orator
OCR-B
HS-Draft
Draft
HS-DRAFT
DRAFT
Note:
The font setting you make with the above procedure can be changed if the
software you are using overrides the setting on the control panel. You can
prevent this by using the following procedure to put the printer into the Font
Lock Mode when you turn it on.
Entering the Font Lock Mode
When the printer is in the Font Lock Mode, the font settings you make on the
control panel are used even if your software tries to override the font. Use the
following procedure to enter the Font Lock Mode.
❏ Turn off the printer.
❏ While holding down FONT, turn printer power on.
The printer is now in the Font Lock Mode. You could enter the Font Lock
Mode and Pitch Lock Mode (page 18) at the same time by holding down
both FONT and PITCH when you turn on printer power.
To exit the Font Lock Mode, simply turn the printer off.
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Control Panel Operations
Setting the character pitch
The character pitch setting controls how many characters are printed per inch.
Use the following procedure to select the pitch you want.
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ Press PITCH to change the pitch selection.
The following shows the meanings of the indicators that light on the control
panel when you press PITCH.
Lit Indicators
Meaning
10CPI
12CPI
10 characters per inch (Pica)
12 characters per inch (Elite)
15 characters per inch
15CPI
10CPI + COND
12CPI + COND
PROP
17 characters per inch (Condensed Pica)
20 characters per inch (Condensed Elite)
Proportional
COND+PROP
Condensed proportional
Note:
The pitch setting you make with the above procedure can be changed if the
software you are using overrides the setting from the control panel. You can
prevent this by using the following procedure to put the printer into the Pitch
Lock Mode when you turn it on.
Entering the Pitch Lock Mode
When the printer is in the Pitch Lock Mode, the pitch settings you make on the
control panel are used even if your software tries to override the pitch. Use the
following procedure to enter the Pitch Lock Mode.
❏ Turn off the printer.
❏ While holding down PITCH, turn printer power on.
The printer is now in the Pitch Lock Mode. You could enter the Pitch Lock
Mode and Font Lock Mode (page 17) at the same time by holding down both
FONT and PITCH when you turn on printer power.
To exit the Pitch Lock Mode, simply turn the printer off.
Download from Www.Somanuals.com. All Manuals Search And Download.
Line feed 19
Line feed
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ Press LINE FEED once to feed paper one line. Holding down LINE FEED
continually feeds paper, one line at a time, until you release the button.
Paper eject (cut-sheet paper)
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ Press SET/EJECT/PARK to eject the paper.
❏ After the paper is ejected, the printer will beep and the POWER indicator
will flash to indicate there is no paper in the printer.
Form feed (fanfold paper)
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ Press FORM FEED and the printer will automatically feed the paper to the
top of the next page.
Parking fanfold paper
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ Press the control panel’s SET/EJECT/PARK button.
❏ The printer automatically reverse feeds the fanfold paper until it is no
longer in contact with the platen.
Micro feed
Use the following operation to feed the paper in very small increments. This
makes it possible to align the print head exactly where you want it.
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ While holding down ON LINE, press LINE FEED to feed the paper
forward or FORM FEED to feed the paper backward.
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Control Panel Operations
Setting the top of form position
The current position of paper loaded in the printer is automatically set as the top
of the page whenever you turn power on. You can also use the following
procedure at any time to specify a different position as the top of the page.
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ Use the micro feed operations (see above) to move the paper so that the
print head is located where you want the new top of form position to be.
❏ While holding down FONT, press SET/EJECT/PARK.
The printer will beep once to indicate that a new top of form position has
been set.
Tear-off function (fanfold paper)
This procedure feeds fanfold paper to a position where it can be torn off easily.
❏ Check to make sure that the printer is on-line.
❏ Press the FORM FEED button to perform the long tear-off operation, or
press the LINE FEED button to perform the short tear-off operation.
The long tear-off operation causes the paper to be fed automatically so the
tear assist edge of the printer cover is aligned with the paper’s next
perforation.
The short tear-off operation causes the paper to be fed automatically so the
tear assist edge of the printer cover is located just below the last line printed
on the paper.
❏ Pull the paper against the tear assist edge to tear it off.
❏ When you resume printing, the printer reverse feeds the paper to its former
position.
Selecting the Quiet Print Mode
The Quiet Print Mode lets you print with less noise than that produced with
normal printing. Use the following procedure to enter and exit the Quiet Print
Mode.
Important!
Though the Quiet Print Mode prints more quietly, it also causes printing to
take considerably longer than normal printing.
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the auto load position 21
❏ Make sure the printer is on-line (ON LINE indicator is lit).
❏ Press SET/EJECT/PARK, to toggle between the Quiet Print Mode and
normal printing.
The printer emits one short beeps when the Quiet Print Mode is selected, and
two short beep when normal printing is selected.
Changing the auto load position
Normally the printer automatically feeds paper to a standard position (1/6-inch
from the top of the paper). This is called the auto load position. You can use the
following procedure to specify a different auto load position.
❏ Make sure the printer is off-line (ON LINE indicator is not lit).
❏ While holding down ON LINE, press SET/EJECT/PARK and then
release the two buttons.
The printer will automatically eject the cut-sheet that is in the printer, or
reverse feed fanfold paper until it is no longer in contact with the platen.
Also, all the font and pitch indicators on the control panel will light.
❏ Press SET/EJECT/PARK to feed the paper to the starting position.
❏ Feed the paper so the print head is located where you want the new auto
load position to be.
Press LINE FEED to feed the paper forward and FORM FEED to feed the
paper backward. This is the micro feed operation.
❏ After you have the paper at the position you want, hold down ON LINE
and press LINE FEED to make the current print head position the new auto
load position. The printer will beep twice to indicate that the new auto load
position is set.
❏ To clear the new auto load position and return to the one that you set
previously (using the above procedure), press ON LINE. To clear the
currently set auto load position and return to the standard position (1/6-inch
from the top of the paper), hold down ON LINE and press SET/EJECT/
PARK.
Note:
The auto load position you set remains in effect until you turn the printer off. If
you want to save the auto load position in memory, press FORM FEED instead
of LINE FEED while holding down ON LINE in the above step.
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Control Panel Operations
Saving a macro
Normally, any settings you make on the control panel are cleared when you turn
the printer off. Use the following procedure to save the current control panel
settings so that they are used whenever you turn the printer on.
❏ Make the control panel settings you want.
❏ Use ON LINE to put the printer off-line (ON LINE indicator is not lit).
❏ Hold down FONT and then PITCH. Keep both buttons held down until the
printer beeps twice.
Pressing FONT normally changes the font setting, so when you press it in
the above step the indicator for the next font lights. Pressing PITCH,
however, returns the font setting to what it was before you pressed FONT.
This procedure saves the following settings.
• Current font and pitch settings
• Quiet Print Mode status
These items can be set separately for the Standard mode and the IBM mode.
❏ To clear saved control panel settings repeat the above procedure, but keep
FONT and PITCH depressed after the printer beeps twice. Soon the printer
will beep again three times to indicate that the saved control panel settings
have been cleared.
Clearing the printer’s buffer
When the printer receives data from a computer, it temporarily stores it in a
memory called a buffer. If you stop a printing job partway through, there is the
chance that some data will remain in the buffer. The following procedure clears
the printer’s buffer by deleting any data that might be there.
❏ Execute the necessary command in the program you are using to stop the
print job.
Important!
Be sure to stop the print job before taking the printer off line. Otherwise, the
print job will resume from where you interrupted it when you put the printer
back on-line.
❏ Use ON LINE to take the printer off line (ON LINE indicator is not lit).
❏ Hold down FONT and then FORM FEED. Keep both buttons held down
until the printer beeps once, which indicates that the buffer is cleared.
Download from Www.Somanuals.com. All Manuals Search And Download.
Initializing the printer 23
Initializing the printer
The following procedure initializes the printer to its power-on settings. If you
have control panel settings stored in memory, this procedure sets up the printer
using them.
❏ Use ON LINE to take the printer off line (ON LINE indicator is not lit).
❏ Hold down FONT and then FORM FEED. Keep both buttons held down
until the printer beeps once (indicating the printer buffer is cleared) and
then beeps again three times, which indicates that the printer is reset.
Entering the Multi-part Mode
When the printer is in the Multi-part Mode, the print head prints with greater
impact. It should be noted, however, that printing in the Multi-part Mode also
reduces the life of the print head. Because of this, you should use the Multi-part
Mode only for printing on four or five-ply paper. Return to the normal mode for
printing on one to three-ply paper.
Use the following procedure to enter the Multi-part Mode
❏ Turn off the printer.
❏ While holding down the control panel’s SET/EJECT/PARK button, turn
the printer back on.
❏ To exit the Multi-part Mode, Simply turn the printer off and back on again.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Chapter 3: Using the EDS Mode
The letters “EDS” stand for “Electronic DIP Switches.” Just like the small DIP
switches that are used by many computers, printers, and other devices, the EDS
mode lets you configure the printer so that it matches your system and software
needs. This chapter describes how to enter the printer’s EDS Mode and provides
details about available settings and how to change them.
All switch settings are ON when the printer is shipped from the factory.
About EDS Mode settings
EDS Mode settings are grouped among six “banks” (representing banks of
switches) that are identified by the letters A through F. Each bank contains a
number of “switches” numbered 1 through 6 that you can turn on and off to
configure the printer.
Entering the EDS Mode
❏ Make sure that paper is loaded in the printer.
❏ Turn off the printer.
❏ While holding down the control panel’s ON LINE, LINE FEED, and
FORM FEED buttons, turn the printer back on.
This causes the following message to be printed, which indicates the printer
is in the EDS Mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a bank 25
Selecting a bank
❏ While in the EDS Mode, use the control panel’s BANK button to select a
bank. When the BANK indicator flashes it indicates the current bank
selected.
Lit Indicator
Selected Bank
A (SANSERIF)
B (COURIER)
C (PRESTAGE)
D (ROMAN)
E (LQ)
A
B
C
D
E
F
F (DRAFT)
Selecting a switch
❏ While in the EDS Mode, use the control panel’s SWITCH button to select a
bank switch. When the SW indicator flashes it indicates the current switch
selected.
Lit Indicator
Selected Switch
1 (10CPI)
2 (12CPI)
3 (15CPI)
4 (COND)
5 (PROP)
6 (QUIET)
1
2
3
4
5
6
Changing a switch setting
❏ After selecting a bank and switch, press the control panel’s ON/OFF
button to turn the switch on and off. The current setting of the switch is
indicated by the ON LINE indicator: the indicator is lit when the switch is
on, and is not lit when the switch is off.
Download from Www.Somanuals.com. All Manuals Search And Download.
26 Using the EDS Mode
Printing the current switch settings
❏ In the EDS Mode, press the control panel’s PRINT button to print out the
current switch settings. Asterisks on the printout show whether a switch is
turned on or off.
Checking the settings of switches in a bank
❏ After selecting a bank, press the control panel’s STATUS button to view
the status of each switch in that bank. The control panel’s font indicator is
lit when the switch is on, and is not lit when the switch is off.
Lit Indicator
Selected Switch
1 (10CPI)
2 (12CPI)
3 (15CPI)
4 (COND)
5 (PROP)
6 (QUIET)
1
2
3
4
5
6
Exiting the EDS Mode
❏ Press the control panels EXIT button to exit the EDS Mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDS Mode Settings 27
EDS Mode Settings
The following details all of the settings you can program in the EDS Mode. You
can print out a detailed overview of all the settings by performing a test of the
printer (page 46).
BANK A
Switch 1: Emulation
Selects Standard emulation (ON) or IBM emulation (OFF). Standard emulation
causes the printer to act like the Epson ESC/P (24-pin), while IBM emulation
makes it act like the IBM Proprinter XL24E.
Switch 2: Character Table
The function of this switch depends on whether you are using IBM or Standard
emulation.
Switch 2
Setting
Emulation
Description
ON
OFF
ON
Graphics: IBM Character Set #2
Standard
Italics: Italic character table used
IBM Character Set #2
IBM
OFF
IBM Character Set #1
Switch 3: RAM Usage
Specifies whether RAM should be used as an input buffer (ON) or as a
download buffer (OFF). Selecting input buffer (ON) tells the printer to use
available RAM to store data it receives from the computer, which speeds up the
printing. Selecting download buffer (OFF) tells the printer to use available
RAM to store character patterns.
Switch 4: Automatic Sheet Feeder
Specifies whether the optional SF-15DM2Automatic Sheet Feeder is installed
(OFF) or not installed (ON).
Switch 5: Paper Out Detector
Specifies whether the printer’s paper out detector is enabled (ON) or disabled
(OFF). When the paper out detector is enabled (ON), the printer automatically
stops printing whenever it senses there is no more paper. When it is disabled
(OFF), the printer continues printing as long as there is data. Selecting disabled
(OFF) makes it possible to print right up to the bottom of a page, but it also
creates the danger of printing when there is no paper loaded in the printer, which
can damage the print head and platen.
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Using the EDS Mode
Switch 6: Multi-Part Mode
Specifies whether the printer’s Multi-Part Mode is enabled (OFF) or disabled
(ON). When the Multi-Part Mode is enabled (OFF), the impact of the print head
is increased, but head life is decreased. Enable the Multi-Part Mode when
printing on four to five-ply paper. Disable the Multi-Part Mode when printing
on 1 to 3-ply paper.
BANK B
Switch 1: Graphics Direction
Selects uni-directional (OFF) or bi-directional (ON) printing for graphics. Bi-
directional printing (ON) is faster, while uni-directional (OFF) printing
generally provides better print quality in the graphics mode.
Switch 2: Auto Tear-off (Long)
Specifies whether the printer’s auto tear-off (long) feature (page 20) is enabled
(OFF) or disabled (ON). Note that this setting controls the application
software’s tear-off function only. It does not affect the manual tear-off function
that is performed using the control panel buttons as described on page 13. The
manual tear-off function is always enabled.
Switch 3: Line Spacing
Selects 1/6-inch (ON) or 1/8-inch (OFF) spacing between lines.
Switch 4: Auto LF with CR
Specifies whether auto LF with CR is enabled (OFF) or disabled (ON). When
auto LF with CR is enabled (OFF), the printer automatically performs a line
feed whenever it receives a carriage return from the computer. When it is
disabled (ON), the computer must send both a line feed code and a carriage
return code at the end of each line. Most applications do this automatically. Note
the following check points when trying to figure out which setting to use here:
✓ If you find that your output is double-spaced when it should not be, turn
this switch ON (Disabled).
✓ If you find that lines are printing over each other, turn this switch OFF
(Enabled).
Switch 5: Zero Style
Specifies whether a normal zero (ON) or a slashed zero (OFF) will be used.
Selecting Normal (ON) prints zeros without lines running through them, while
Slashed (OFF) prints zeros with a diagonal slash running through them.
Switch 6: Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
EDS Mode Settings 29
BANK C
Switches 1, 2: Print Mode
Turn these switches on or off to select the print mode you want to use.
Print Mode
SW1
SW2
LQ
ON
OFF
ON
ON
ON
Draft
HS-Draft
OFF
Switches 3, 4, 5: Print Pitch
Turn these switches on or off to form the pattern that matches the print pitch
setting you want to make.
Print Pitch
SW3
SW4
SW5
10cpi
12cpi
ON
OFF
ON
ON
ON
ON
ON
15cpi
OFF
OFF
ON
ON
17cpi
OFF
ON
ON
20cpi
OFF
OFF
Proportional
OFF
ON
Switch 6: Quiet
When the Quiet Mode is enabled (OFF), the printer prints with less noise than
normal printing. Though the Quiet Mode prints more quietly, it also takes
considerably longer than normal printing.
Download from Www.Somanuals.com. All Manuals Search And Download.
30 Using the EDS Mode
BANK D
Switches 1, 2, 3, 4: Page Length
Turn these switches on or off to form the pattern that matches the Page Length
setting you want to use.
Page Length
SW1
SW2
SW3
SW4
11”/Letter
8”
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
11.7”/A4
12”
OFF
OFF
ON
ON
OFF
ON
ON
8.5”/Letter
14”/Legal
10.5”/Executive
7.25”/Executive
3.5”
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
5.5”
OFF
ON
ON
Switch 5: CR Centering Position
If you set this switch OFF, the carriage moves to the center each time to feed
paper near the perforation. This way, you can get better quality of printing
around the perforations. It is recommended to match the page length setting to
your fanfold paper, otherwise, this function does not work properly at the
perforations.
If you leave this switch ON, the carriage does not move when feeding paper.
Switch 6 : Not used
BANK E
Switches 1, 2, 3, 4, 5: Code Page/International Character Set
If your EDS settings specify IBM emulation (Bank A, Switch 1 OFF) with
either character table (Bank A, Switch 2), or Standard emulation (Bank A,
Switch 1 ON) with the graphics character table (Bank A, Switch 2 ON), use the
Bank E switches to select the default character code page you want to use.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDS Mode Settings 31
Code Page
SW1
SW2
SW3
SW4
SW5
SW6
#437 IBM-PC
#850 Multi-lingual
#860 Portuguese
#861 Icelandic
#863 Canadian French
#865 Nordic
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
#866 Russian
OFF
OFF
ON
ON
ON
#3840 IBM-Russian
#3841 Gost-Russian
#3843 Polish
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
#3844 CS2
OFF
OFF
ON
ON
ON
#3845 Hungarian
#3846 Turkish
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
#3847 Brazil-ABNT
#3848 Brazil-ABICOMP
#852 Latin-2
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
#1001 Arabic
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#737 Greek
OFF
ON
ON
ON
ON
#851 Greek
OFF
OFF
ON
ON
ON
#869 Greek
OFF
ON
ON
ON
#928 Greek
OFF
OFF
OFF
OFF
ON
ON
#2001 Lithuanian-KBL
#772 Lithuanian
#774 Lithuanian
#3001 Estonian-1
#3002 Estonian-2
#3011 Latvian-1
#3012 Latvian-2
#3021 Bulgarian
#3031 Hebrew
#3041 Maltese
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
32 Using the EDS Mode
Code Page
SW1
SW2
SW3
SW4
SW5
SW6
#3850 Standard KU
#3860 Rajvitee KU
#3861 Microwiz KU
#3863 STD 988 TIS
#3864 Popular TIS
#3865 Newsic TIS
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
EDS Mode Settings 33
A code page is the set of symbols and characters that your printer can print. Your
printer converts ASCII hexadecimal data according to a code page to print
symbols and characters. By supporting different code pages, the printer can
print in a variety of different languages. The following table shows detailed
information about code pages.
Code Page
Name
Country
Remarks
United Kingdom, France, Germany, Italy,
Austria, Switzerland, United States, Spain
#437
IBM PC
United Kingdom, France, Germany, Italy,
Austria, Switzerland, United States, Spain
Preferred by Microsoft
#850
Multi-Lingual
#860
#861
Portuguese
Icelandic
Portugal
Iceland
Canada
Canadian
French
#863
#865
#866
Nordic
Russian
Denmark, Finland, Norway, Sweden
Preferred by Microsoft
Preferred by Microsoft
Russia
#3840
#3841
#3843
#3844
#3845
#3846
#3847
#3848
IBM-Russian
Gost-Russian
Polish
Russia, Bulgaria
Russia
Gost: government standard
Also called “Mazowia”
Poland
CS2
Czech Republic
Hungary
Also called “Kamenicky”
Hungarian
Turkish
Turkey
Brazil-ABNT
Brazil-ABICOMP
Croatia, Czech Republic, Hungary,
Poland, Romania, Serbia, Slovak
Republic, Slovenia
Preferred by Microsoft
#852
Latin-2
Arabic
Egypt, Saudi Arabia
Mainly in Arabic speaking
countries
#1001
#737
#851
Greek
Greek
Greece
Greece
Almost 80%
Download from Www.Somanuals.com. All Manuals Search And Download.
34 Using the EDS Mode
Code Page
Name
Country
Remarks
#869
#928
Greek
Greek
Greece
Greece
Lithuania
Lithuania
Lithuania
Estonia
Estonia
Latvia
For UNIX
#2001
#772
Lithuanian-KBL
Lithuanian
Lithuanian
Estonian-1
Estonian-2
Latvian-1
Commonly used for DOS
New standard
#774
#3001
#3002
#3011
#3012
#3021
#3031
#3041
#3850
#3860
#3861
#3863
#3864
#3865
Most often used
Latvian-2
Latvia
Government standard
Bulgarian
Bulgaria
Israel
Hebrew
Maltese
Malta
Standard KU
Rajvitee KU
Microwiz KU
STD988 TIS
Popular TIS
Newsic TIS
Thailand
Thailand
Thailand
Thailand
Thailand
Thailand
Download from Www.Somanuals.com. All Manuals Search And Download.
EDS Mode Settings 35
If your EDS settings specify Standard emulation (Bank A, Switch 1 ON) with
the italic character table (Bank A, Switch 2 OFF), use the Bank E switches to
select the international character set you want to use. This setting determines the
assignment of 14 character codes in the Standard Italic character set.
International
Character Set
SW1
SW2
SW3
SW4
SW5
SW6
U.S.A.
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
France
Germany
England
Denmark-1
Sweden
Italy
OFF
OFF
ON
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
ON
ON
Spain-1
Japan
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Norway
Denmark-2
Spain-2
Latin America
Korea
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
Ireland
OFF
OFF
Legal
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
36 Using the EDS Mode
BANK F
Switches 1, 2, 3, 4, 5: LQ Font Selection
Turn these switches on or off to form the pattern that identifies the font you want
to use for LQ printing.
Font
SW1
SW2
SW3
SW4
SW5
Roman
Sanserif
Courier
Prestige
OCR-B
Orator
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
Note:
Bank C switches 1 and 2 need to be in the correct positions before the above
setting will have any effect.
Switch 6: Not used
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Chapter 4: Using the Printer with MS-DOS
This chapter contains information about how to use the printer with applications
software running under MS-DOS. In this chapter, you will learn about:
❏ How to set up for printing with MS-DOS
Setting up for printing with MS-DOS
To print from an application running under MS-DOS, you must first select the
printer from within the application. Typically, the program will feature an
INSTALL or SETUP command for selection of printers. Refer to the manual
for the application you are using for details on how to select a printer for it.
❏ Start up the application and use the correct procedure for that application to
select a printer. The following is a list of printers that can be used. If your
application lists more than one of these, select the printer that is nearest to
the top of this list. You should also use the EDS mode or User Setup Utility
to select Standard emulation (page 27).
Star XB24-250
2
Star XB24-250/XB-2425
Star LC-4511/4521
Epson LQ-860/1060
Epson LQ-850/1050
If none of the printers listed above are available in the application, choose
one of the printers listed below. Once again, you should choose the printer
that is nearest to the top in the following list. For these printers, you should
use the EDS Mode or User Setup Utility to select IBM emulation (page 27).
IBM Proprinter X24E/XL24E
IBM Proprinter X24/XL24
❏ To print, follow the instructions given in the manual of the application you
are using. Typically, you would select the application’s PRINT command,
make any necessary changes in the window that appears (such as the
number of copies to be printed), and then press the Enter key to start
printing.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Chapter 5: Paper Handling
Your printer is designed to print on a variety of paper types. This chapter tells
you everything you need to know about paper, and how to set the printer up for
manual paper feed. In this chapter, you will learn about:
❏ Selecting the best type of paper
❏ Adjusting for paper thickness
❏ Manual sheet feeding
❏ Clearing paper jams
Selecting paper types
Use the following information when selecting paper. Note that printing is
supported for both portrait and landscape orientation unless specifically noted
otherwise.
Cut-Sheet Paper (Manual Feed)
Width:
Length:
Size:
Thickness:
Weight:
7.2″ to 16.5″ / 183 to 420mm
5.5″ to 14.3″ / 140 to 364mm
B5, A4, Letter, Legal, B4 (Landscape), A3 (Landscape)
0.00276″ to 0.00472″ / 0.07 to 0.12mm (1-ply only)
2
14 to 24 lbs / 52 to 90g/m / 45 to 77 kg
Cut-Sheet Paper (with Optional Automatic Sheet Feeder)
Width:
Length:
Size:
Thickness:
Weight:
Hopper:
Stacker:
7.2″ to 16.5″ / 183 to 420mm
7.2″ to 14″ / 183 to 356mm
B5, A4, Letter, Legal, B4 (Landscape), A3 (Landscape)
0.00315″ to 0.00472″ / 0.08 to 0.12mm (1-ply only)
2
16 to 24 lbs / 60 to 90g/m / 52 to 77 kg
2
2
50 sheets of 64g/m , 30 sheets of 80g/m
10 sheets
Fanfold Paper
Width (push feed): 4″ to 16.0″ / 101.6 to 406mm
Width (pull feed): 4″ to 16.0″ / 101.6 to 406mm
Thickness:
0.00276″ to 0.00433″ / 0.07 to 0.11mm (1-ply)
0.01378″ / 0.35mm max. (total thickness of multi-ply, non-
carbon)
2
Weight:
Copies:
14 to 22 lbs / 52 to 81g/m / 45 to 70 kg (1-ply)
2
11 to 14 lbs / 40 to 52g/m / 34 to 45 kg (multi-ply)
Original + 1 or 2 (Normal Mode)
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting for paper thickness 39
Original + 3 to 4 (Multi-Part Mode)
Multi-part Mode and an optional pull tractor are
recommended when printing on 4 or 5-ply paper.
Adjusting for paper thickness
Paper comes in different weights, normally expressed as gsm (grams per square
meter) or lbs (pounds). Some form paper also has multiple pages that make them
quite thick. Use the following procedure to change the gap between the print
head and the platen and adjust for paper thickness.
❏ Move the adjustment lever to one of its settings. Position 2 or 3 is most
suitable for single-sheet paper.
Download from Www.Somanuals.com. All Manuals Search And Download.
40 Paper Handling
The following table provides a general guide for setting the adjustment lever.
Experiment with different settings until you find the one that gives you the print
quality you want.
Recommended
Paper Type
Weight Per Sheet
Thickness
Position
2
Cut-sheet
52 to 90 g/m
0.07 to 0.12mm
0.07 to 0.12mm
0.12 to 0.16mm
0.18 to 0.25mm
0.24 to 0.30mm
0.30 to 0.35mm
2 or 3
2 or 3
2 or 3
3 or 4
4 or 5
5 or 6
2
1-ply
2-ply
3-ply
4-ply
5-ply
52 to 90 g/m
2
40 to 52 g/m
2
Fanfold
40 to 52 g/m
2
40 to 52 g/m
2
40 to 52 g/m
Important!
Continuous use of the wrong adjustment lever setting can drastically reduce
print head life! The Multi-part Mode is recommended when printing on 4 or 5-
ply paper.
Automatic fanfold feeding
❏ See “Loading fanfold paper” on page 9 for details on using fanfold paper.
Manual sheet feeding
You can use the following procedure to manually feed single sheets of paper
into the printer.
❏ Make sure that there is no fanfold paper in the printer. If there is, use the
procedure under “Parking fanfold paper” on page 13 to park the fanfold
paper and prepare for manual sheet feeding.
❏ Set the release lever to the cut-sheet position.
❏ Stand up the paper guide (page 8).
❏ Align the left paper guide with the scale mark that matches the size of the
paper you are using.
For any paper size other than A3 landscape (horizontal), align the paper
guide with scale 0 (zero). For A3 landscape paper, align the paper guide with
the far left
mark.
❏ Adjust the right paper guide so there is enough space to insert the paper.
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing paper jams 41
Insert a sheet of paper into the paper guide, with the side you want to print on
facing the back of the printer. Gently lower the paper down into the printer until
you feel it stop.
❏ Press the SET/EJECT/PARK button to feed the paper to the starting
position.
❏ If you want to move the paper to another position, use the micro feed
function described under “Micro feed” on page 19.
❏ Start the printing operation from your software application.
Clearing paper jams
Use the following procedure to clear paper jams from the printer.
❏ Unplug the printer from its AC power outlet.
❏ Open the front cover of the printer.
❏ Carefully try to pull the jammed paper from the printer.
If necessary, change the release lever position or rotate the platen knob to
remove the paper.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Chapter 6: Optional Accessories
This chapter introduces the following optional accessories that are available for
this printer:
❏ Automatic Sheet Feeder (SF-15DM2)
❏ Pull Tractor Unit (PT-15XM)
❏ Serial Interface Cartridge (IS-8XL)
❏ Baffered Parallel Interface Cartridge (IP-128XL)
❏ Serial-to-Parallel Converter (SPC-8K)
Important!
Always make sure that printer power is turned off whenever installing or
removing optional accessories.
2
Automatic Sheet Feeder (SF-15DM )
The automatic sheet feeder automatically feeds cut sheet paper into the printer.
Preparing the printer
❏ Use the printer’s EDS Mode to change the setting of Bank A Switch 4 to
OFF (page 27), which tells the printer that the automatic sheet feeder is
installed.
Refer to the manual that comes with the automatic sheet feeder for further
details on installation and operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
Pull Tractor Unit (PT-15XM) 43
Pull Tractor Unit (PT-15XM)
The pull tractor unit is recommended when printing with multi-part continuous
forms.
Refer to the manual that comes with the pull tractor unit for further details on
installation and operation.
Serial Interface Cartridge (IS-8XL)
Installing the serial interface cartridge provides serial data communications
capabilities between the printer and your computer.
Refer to the manual that comes with the serial interface cartridge for further
details on installation and operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
44 Optional Accessories
Buffered Parallel Interface Cartridge (IP-128XL)
Installing the parallel interface cartridge provides parallel data communications
capabilities between the printer and your computer.
Refer to the manual that comes with the buffered parallel interface cartridge for
further details on installation and operation.
Serial-to-Parallel Converter (SPC-8K)
Connecting the serial-to-parallel converter to the printer’s parallel connector
provides serial data communications capabilities between the printer and your
computer.
Serial con n ector
Dip switch
Clear bu tton
Parallel con n ector
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial-to-Parallel Converter (SPC-8K) 45
Specifications
Interface
RS-232C-level
Asynchronous
Synchronization
Baud rate
Word length
Start bit
150, 300, 600, 1200, 2400, 4800, 9600, 19200 BPS (selectable)
1
Data bits
Parity bit
Stop bits
Signal polarity
Mark
7 or 8 (selectable)
Odd, even, none (selectable)
One or more
Logical 1 (-3V to -15V)
Logical 0 (+3V to +15V)
DTR, XON/XOFF, ETX/ACK
8 kbytes (standard)
Space
Handshaking
Data buffer
Refer to the manual that comes with the serial-to-parallel converter for further
details on installation and operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Appendix A: Troubleshooting
This appendix will help you if you experience problems with your printer. It
tells you how to test the printer, how to check system software settings, and how
to adjust the vertical alignment. In addition, there is information on actions to
take for specific problems.
Warning!
The printer uses high voltage. Do not attempt any other repair or maintenance
except as expressly recommended in this appendix. Unauthorized repair and
maintenance not only exposes you to the danger of electrical shock, it also may
damage your printer and void your warranty.
Testing the printer
There are two different tests you can use: a self test and a hexadecimal dump.
Self test
❏ Make sure that paper is loaded in the printer.
❏ Turn the printer off.
❏ While holding down the control panel’s ON LINE button or LINE FEED
button, turn the printer on.
❏ To stop demo printing, turn the printer off.
Note:
● The self test prints across the entire width of the carriage. Make sure that
the printer is loaded with the widest paper available in order to avoid
damage to the print head and platen.
● Since this test can generate many lines of text and graphics, it is a good idea
to perform this test only when using continuous fanfold paper rather than
single sheets.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hexadecimal dump 47
Hexadecimal dump
This procedure prints in hexadecimal format all codes (character codes and
control codes) that are sent to the printer by the computer. The printer does not
execute any control codes (such as 0A - linefeed), it just prints them out. The
hexadecimal dump is useful when you are writing programs for printer control.
❏ Make sure that paper is loaded in the printer.
❏ Turn off the printer.
❏ While holding down the control panel’s FORM FEED button, turn the
printer back on to enter the Hex Dump Mode.
❏ The printer will now print out the hexadecimal values of any data that is
subsequently sent to it from your computer.
❏ To exit the Hex Dump Mode, first press ON LINE to set the printer off-line,
and then turn the printer off.
Adjusting the dot alignment
You may never have to use the procedure described in this section, but after you
have been using your printer for some time you may find that the dots of some
graphics do not align correctly. For example, what should look like:
may come out looking like one of the following:
or like this
This is caused when mechanical parts of the printer get out of alignment. This
happens only rarely and you may never experience it at all throughout the life
of the printer. If you do have problems, use the following procedure to correct it.
❏ Make sure that paper is loaded in the printer.
❏ Turn off the printer.
Download from Www.Somanuals.com. All Manuals Search And Download.
48 Troubleshooting
❏ While holding down the control panel’s FORM FEED and ON LINE
buttons, turn the printer back on to enter the Dot Adjustment Mode.
The printer will print something like the following.
*** DOT ADJUSTMENT SETTING ***
Normal-density
0:
Note that the printer will feed the paper forward and back each time during
this operation so you can view the printout.
❏ If the two lines do not align properly, use FONT to move the middle line to
the left or PITCH to move it to the right.
The above step performs alignment for Normal-density mode only. You
must make separate adjustments for the HS-DRAFT, CRT graphics mode I,
DRAFT Graphics, DRAFT Graphics Speed Down, Double-density, CRT
graphics mode II, CRT graphics mode2SD, Triple-density, Quadruple-
density, LQ Graphics, LQ Graphics Speed Down modes as well.
❏ Press SET/EJECT/PARK to change to another printing mode.
❏ Repeat the above steps for each printing mode, if necessary.
❏ After making changes to adjustments in all the printing modes you want,
press ON LINE to exit the Dot Adjustment Mode and register your
adjustments.
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Troubleshooting guide
Use the following table to help track down the causes of problems and to determine the
best solution to deal with them.
Problem
Possible Cause
Recommended Action
The ON LINE indicator does
not light.
The printer is not receiving
power.
Check whether the power
cord is correctly plugged into
the power outlet.
Check whether the power
outlet is working by
unplugging the printer and
plugging in another device.
Printer sounds like it is
printing, but it is not.
The ribbon is jammed,
twisted, or not set correctly
between the print head and
the print head shield.
Make sure that the ribbon
cassette is installed
correctly.
Printing is weak.
The printer is not set up
correctly for the thickness of
paper you are using.
Set up the printer for the
paper thickness you are
using. See “Adjusting for
paper thickness” on
page 39.
The ribbon is worn out or
“used up.”
Replace the ribbon with a
new one.
Printer test works, but printer
will not print out data from
the attached computer.
Your application program’s
or system software’s printer
selection is wrong.
Check the printer selection
of your application software.
The computer’s system
software is not set up
properly for the printer or for
the port you are using.
Check the system software
settings. Check the settings
for LPT1, COM 1, or COM 2
if you are using the optional
serial interface unit.
The interface cable is
connected incorrectly or
damaged.
Check to make sure that the
printer interface cable is
connected correctly. If it is,
try a different cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
50 Troubleshooting
Problem
Possible Cause
Recommended Action
Printer case is hot.
The printer’s air vents are
blocked or obstructed.
Switch off the printer and let
it cool. Check the air vents
on the bottom of the printer
to see if they are blocked.
Remove the obstruction if
possible. If the problem
persists, return the printer to
your dealer for repair.
Printer makes excessive
noise.
The front cover is removed.
The printer is vibrating.
Replace the front cover.
Move any objects that are
touching the printer.
Make sure that the printer is
on a level steady surface.
Printer prints past the edge
of the paper.
Incorrect margin settings
are selected by your
application program.
Choose different margin
settings from your
application program.
The paper guide is not
positioned correctly.
Remove the paper and
adjust the position of the
paper guide. Reload the
paper and try printing again.
The ribbon is jammed,
causing the print head to
jam.
Make sure that the ribbon
cassette is installed
correctly. See “Installing the
ribbon cartridge” on page 5.
Paper is jamming, causing
the print head to jam.
Remove all paper from the
printer and reload it. Try
printing again.
Set up the printer for the
paper thickness you are
using. See “Adjusting for
paper thickness” on
page 39.
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Problem
Possible Cause
Recommended Action
Left margin moves to the
right during printing.
The paper is not loaded
correctly, causing the print
head to jam.
Remove all paper from the
printer and reload it. Try
printing again.
The ribbon cassette is not
installed correctly, causing
the print head to jam.
Make sure that the ribbon
cassette is installed
correctly. See “Installing the
ribbon cartridge” on page 5.
The printer is not set up
correctly for the thickness of
paper being used.
Set up the printer for the
paper thickness you are
using. See “Adjusting for
paper thickness” on
page 39.
Inappropriate settings are
selected by your application
program.
Choose different settings in
your application.
Static electricity caused by
interference from nearby
electrical devices or by low-
level humidity is affecting
printer operation.
Make sure that the printer is
not too close to any devices
with electric motors or try to
raise the humidity level.
Some characters are printed
incorrectly.
Static electricity caused by
interference from nearby
electrical devices or by low-
level humidity is affecting
printer operation.
Make sure that the printer is
not too close to any devices
with electric motors or try to
raise the humidity level.
Inappropriate settings are
selected by your application
program.
Choose different settings in
your application.
Wires are missing from the
print head.
Return the printer to your
dealer for repair.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Checking system software settings in MS-DOS
If you are using a parallel cable and cannot print a text file using the MS-DOS
PRINT command, you may have a problem with your AUTOEXEC.BAT file.
Open the file and look for the following line:
MODE LPT1:=COM1 or MODE LPT1:=COM2
These lines indicate you are using a serial cable connection, and so you should
delete them, save the AUTOEXEC.BAT file, reboot and try printing again.
Of course, if you are having problems printing with the optional serial-to-
parallel converter or optional serial interface unit, you should conversely check
to make sure that one of the above lines is included in your AUTOEXEC.BAT
file. The file must also contain information on parameter settings. For details,
see the user’s manual that comes with the optional serial-to-parallel interface
converter or optional serial interface unit.
If the above is not the problem or if you make the above changes and still
experience problems printing using the MS-DOS PRINT command, refer to
your MS-DOS Users’ Guide or consult your software dealer.
If you are successful in printing using the MS-DOS PRINT command but
cannot print from an application, check to see what printer driver is selected in
the application. See “Setting up for printing with MS-DOS” on page 36. If this
does not help, consult your software dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Appendix B: Specifications
Printing System
Printing Speed
Serial Impact Dot-Matrix
Pitch
Draft (cps/dpi)
LQ (cps/dpi)
283/120H (Normal)
350/80H (HS)
Pica (10 cpi)
94/360H
Elite (12 cpi)
340/120H
425/120H
212/240H
242/240H
283/240H
340/240H
113/360H
141/360H
141/360H
161/360H
188/360H
226/360H
Semi-condensed (15 cpi (S))
Semi-condensed (15 cpi (I))
Condensed pica (17 cpi)
Condensed elite (20 cpi)
24 cpi (I)
H: half-dot
(S): Standard mode only
(I): IBM mode only
Print Direction
Print Head
Draft:
Uni-directional/ bi-directional logic seeking (selectable)
Uni-directional/ bi-directional logic seeking (selectable)
Uni-directional/ bi-directional logic seeking (selectable)
24
LQ:
Bit-Image:
Number of pins:
Life:
200 million dots/pin (Normal Mode)
100 million dots/pin (Multi-Part Mode)
Line Spacing
1/6
7/72
″
, 1/8″, 7/60″, n/180″, n/360
/72 /216 : software
Pitch
″
″
,
n
″
,
n
″
Character Matrix
Draft
LQ
24
24
×
9H (Normal)
7H (HS)
Pica (10 cpi)
Elite (12 cpi)
24
×
31H
×
24
16
24
24
24
24
×
×
×
×
×
×
9H
7H
9H
9H
9H
9H
24
16
24
24
24
24
×
×
×
×
×
×
27H
21H
16H
16H
16H
14H
Semi-condensed (15 cpi(S))
Semi-condensed (15 cpi(I))
Condensed pica (17 cpi)
Condensed pica (20 cpi)
24 cpi (I)
H: half-dot
(S): Standard mode only
(I): IBM mode only
Download from Www.Somanuals.com. All Manuals Search And Download.
54 Specifications
Environment
Operating temperature:
Storage temperature:
Operating humidity:
Storage humidity:
41
°
F to 95
°
F (5
°
C to 35
°C)
–22
°
F to 149
°
F (–30
°
C to 65°C)
30% to 80% (non-condensing)
20% to 90% (non-condensing)
Paper
Cut-sheet (manual feeding)
Paper width:
7.2
″
to 16.5
″
″
/ 183 to 420 mm
/ 140 to 364 mm
Paper length:
Paper thickness:
Paper weight:
5.5″
to 14.3
0.00276
″
to 0.00472
″
/ 0.07 to 0.12 mm
2
14 to 24 lbs. / 52 to 90 g/m / 45 to 77 kg
Cut-sheet (with optional automatic sheet feeder)
Paper size:
B5, A4, LT, B4, A3, Legal
Paper thickness:
Paper weight:
Hopper:
0.00315
″
to 0.00472
″
/ 0.08 to 0.12 mm
2
16 to 24 lbs. / 60 to 90 g/m / 52 to 77 kg
2
50 sheets of 64 g/m
30 sheets of 80 g/m
2
Stacker:
10 sheets
Fanfold (with push tractor feeder)
Paper width:
4
″
to 16.0
0.00276 to 0.00433
0.01378 / 0.35 mm maximum (total thickness of multi-
ply paper, non-carbon)
″
/ 101.6 to 406 mm
Paper thickness:
″
″
″
/ 0.07 to 0.11 mm (one-ply)
2
Paper weight:
Copies:
14 to 22 lbs. / 52 to 82 g/m / 45 to 70 kg (one-ply)
11 to 14 lbs. / 40 to 52 g/m / 34 to 45 kg (multi-ply)
2
Original + 1 or 2 (Normal Mode)
Original + 3 or 4 (Multi-Part Mode)
* Multi-Part Mode is recommended when using
optional pull tractor unit.
Fanfold (with optional pull tractor feeder)
Paper width:
4
″
to 16.0
0.00276 to 0.00433
0.01378 / 0.35 mm maximum (total thickness of multi-
ply paper, non-carbon)
″
/ 101.6 to 406 mm
Paper thickness:
″
″
″
/ 0.07 to 0.11 mm (one-ply)
2
Paper weight:
Copies:
14 to 22 lbs. / 52 to 82 g/m / 45 to 70 kg (one-ply)
11 to 14 lbs. / 40 to 52 g/m / 34 to 45 kg (multi-ply)
2
Original + 1 or 2 (Normal Mode)
Original + 3 or 4 (Multi-Part Mode)
Emulation
Standard Mode:
EPSON ESC/P (24-pin)
NEC Graphic compatible
IBM Mode:
Standard:
Option:
Proprinter XL24E
Centronics parallel
RS-232C serial
Interface
Ribbon Type
On-carriage, dedicated
Fabric monochrome ribbon
Color ribbon
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Ribbon Life
Fabric monochrome ribbon (LZ24HD): 4.0 million characters (draft pica)
Color ribbon (X24CL): 1.0 million characters
Dimensions and weight
Width:
Depth:
Height:
Weight:
23.9
″
″
/ 608 mm
/ 400 mm
15.8
6.2″
/ 157 mm
27.2 lbs. / 12.3 kg
Power Supply
230V AC +14%/–13%; 50/60Hz
Power Consumption
15W during standby / 70W during ASCII draft printing
PT-15XM Pull Tractor Unit
Options
SF-15DM
IS-8XL Serial Interface Unit
2
Single-Bin Automatic Sheet Feeder
IP-128XL Parallel Interface Unit
SPC-8K Serial-To-Parallel Converter
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Appendix C: Interface Pin Outs
Parallel Interface
Pin
Name
Function
1
2
STROBE
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
ACK
Goes low for 0.5µs when active.
These signals represent information for the 1st through 8th bit of parallel data,
respectively. Each signal is HIGH when data is logical 1, and LOW when logical
0.
≥
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 - 30
31
32
33
34 - 35
36
10µs low to acknowledge receipt of data.
BUSY
Printer sets line low when ready to receive data.
High when paper runs out.
High when printer is on-line.
Printer ignores this signal
Not used.
PAPER
SELECT
AFXT
SIGNAL GND
CHASSIS
+5V
Signal ground
Chassis ground (isolated from signal ground)
+5V DC output from printer
Twisted pair ground return
Printer is reset when this signal goes low.
Low when printing cannot continue due to error.
External ground
GND
RESET
ERROR
EXT GND
Not used
SELECT IN
Printer ignores this signal
Optional Serial Interface
Pin
Name
Function
1
GND
TXD
RXD
RTS
CTS
Printer chassis ground
2
Data from printer
3
Data to printer
4
5
Always space
Space when computer is ready to send data. Printer ignores this signal.
6
Not used.
7
GND
RCH
DTR
Signal ground
8 - 10
11
Not used.
Printer sets line to space when ready to receive data. Same signal as Pin 20.
12 - 19
20
Not used.
Printer sets line to space when ready to receive data.
Not used.
21 - 25
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Appendix D: Character Sets
Standard Italic Character Set
International Character Set
The character codes shown in the table are hexadecimal.
Download from Www.Somanuals.com. All Manuals Search And Download.
58 Character Sets
IBM Character Set #2
Code Page #437 (IBM-PC)
Character Set #1
Other characters are the same as those for Character Set #2.
Download from Www.Somanuals.com. All Manuals Search And Download.
59
IBM Special Character Set
The following characters can be printed
using the <ESC> ^ command.
Code Page #850
Multi-lingual
Other characters are the same as those for
Code Page #437.
Code Page #860
Portuguese
Code Page #861
Icelandic
Other characters are the same as those for Other characters are the same as those for
Code Page #437.
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
60 Character Sets
Code Page #863
Canadian French
Code Page #865
Nordic
Other characters are the same as those for Other characters are the same as those for
Code Page #437.
Code Page #437.
Code Page #3840
Code Page #866
IBM-Russian
Russian
Other characters are the same as those for
Code Page #437.
Other characters are the same as those for
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Code Page #3843
Polish
Other characters are the same as those for
Code Page #437.
Code Page #3841
Gost-Russian
Other characters are the same as those for
Code Page #437.
Code Page #3845
Code Page #3844
CS2
Other characters are the same as those for
Code Page #437.
Hungarian
Other characters are the same as those for
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Code Page #3847
Code Page #3846
Turkish
Other characters are the same as those for
Code Page #437.
Brazil-ABNT
Other characters are the same as those for
Code Page #437.
Code Page #852
Latin-2
Code Page #3848
Brazil-ABICOMP
Other characters are the same as those for
Code Page #437.
The other characters are the same as in
code page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Code Page #1001
Arabic
Code Page #737
Greek
Code Page #851
Greek
Other characters are the same as those for Other characters are the same as those for
Code Page #437.
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
64 Character Sets
Code Page #869
Greek
Code Page #928
Greek
Other characters are the same as those for Other characters are the same as those for
Code Page #437.
Code Page #437.
Code Page #2001
Lithuanian-KBL
Code Page #772
Lithuanian
Other characters are the same as those for Other characters are the same as those for
Code Page #437.
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Code Page #774
Lithuanian
Code Page #3001
Estonian1
Other characters are the same as those for Other characters are the same as those for
Code Page #437.
Code Page #437.
Code Page #3002
Estonian2
Code Page #3011
Latvian1
Other characters are the same as those for Other characters are the same as those for
Code Page #437.
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
66 Character Sets
Code Page #3021
Code Page #3012
Latvian2
Other characters are the same as those for
Code Page #437.
Bulgarian
Other characters are the same as those for
Code Page #437.
Code Page #3041
Maltese
Other characters are the same as those for
Code Page #437.
Code Page #3031
Hebrew
Other characters are the same as those for
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Code Page #3860
Rajvitee KU
Other characters are the same as those for
Code Page #437.
Code Page #3850
Standard KU
Other characters are the same as those for
Code Page #437.
Code Page #3863
Code Page #3861
STD988 TIS
Microwiz KU
Other characters are the same as those for
Code Page #437.
Other characters are the same as those for
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Code Page #3865
Code Page #3864
Newsic TIS
Popular TIS
Other characters are the same as those for
Code Page #437.
Other characters are the same as those for
Code Page #437.
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking system software settings in MS-DOS 69
Appendix E: Printer Control Codes
This appendix lists the printer’s control commands. It gives the name of each control
command, along with the applicable emulation mode (Standard and IBM), and the
applicable ASCII code.
Standard Mode
ASCII Code
Function
BEL
Beeper
BS
Backspace
HT
Tab horizontally
Line feed
LF
VT
Tab vertically
FF
Form feed
CR
Carriage return
Select double width printing (1 line)
Select condensed printing
Select printer
SO
SI
DC1
DC2
Cancel condensed printing
Deselect printer
DC3
DC4
Cancel double width printing (1 line)
Cancel line
CAN
ESC LF
ESC FF
ESC SO
ESC SI
ESC EM n
ESC SP
ESC ! n
Reverse feed by current line space
Reverse form feed
Select double width printing (1 line)
Select condensed printing
Control cut-sheet feeder (printer ignores this code)
Set inter character space
Master select
10 cpi
n = 00
(ESC P)
(ESC M)
(ESC p)
(SI)
(ESC E)
(ESC G)
(ESC W)
(ESC 4)
(ESC -)
01
02
04
08
10
20
40
80
12 cpi
Proportional
Condensed
Emphasised
Double-strike
Double-wide expanded
Italic
Underlining
ESC #
Cancel MSB control
Download from Www.Somanuals.com. All Manuals Search And Download.
70 Printer Control Codes
Standard Mode
ASCII Code
Function
Set absolute horizontal print position
Select user defined characters
ESC $ nL nH
ESC % n
n = 00
01
Normal (ROM) characters
User-defined (RAM) characters
ESC & 00 n m a1 a2 a3
d1...dk
Define user defined characters
ESC (- nL nH m d1 d2
Select line/score
d1 = 01
02
Underline
Strikethrough
03
Overscore
d2 = 00
01
Turn off scoring
Single continuous line
Double continuous line
Single broken line
Double broken line
02
05
06
ESC (^ nL nH d1...dk
Print data as characters
Assign character table
ESC (t 03 00 d1 d2 00
d1 = ESC t d1
d2 = 00
01
Italic
USA
Multi-lingual
Portuguese
Icelandic
Canadian French
Nordic
Russian
IBM-Russian
Gost
Polish
CS2
Hungarian
Turkish
Brazil-ABNT
Brazil-ABICOMP
Latin-2
#437
03
#850
#860
07
19
#861
08
#863
09
#865
1A
#866
1B
#3840
#3841
#3843
#3844
#3845
#3846
#3847
#3848
#852
1C
1D
1E
1F
20
21
22
18
ESC * m nL nH d1...dk
ESC + n
Select bit-image
Set n/360 line spacing
Turn under line on/off
″
ESC - n
n = 00
01
Turns underline off
Turns underline on
ESC / m
ESC 0
Select vertical tab channel
Select 1/8
″
″
line spacing
line spacing
ESC 2
Select 1/6
ESC 3 n
ESC 4
Select n/180″ line spacing
Select italic font
Cancel italic font
ESC 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking system software settings in MS-DOS 71
Standard Mode
ASCII Code
Function
ESC 6
Enable printing of upper control codes (Character Set #2)
Enable upper control codes (Character Set #1)
Disable paper out detector
Enable paper out detector
Unidirectional mode (1 line)
Set MSB to 0
ESC 7
ESC 8
ESC 9
ESC <
ESC =
ESC >
Set MSB to 1
ESC ? n m
ESC @
Reassign bit-image mode
Initialise printer
ESC A n
ESC B d1...dk 00
ESC C n
ESC C 0 n
ESC D n1...nk 00
ESC E
Set n/60″ line spacing
Set vertical tab
Set page length in lines
Set page length in inches
Set horizontal tab
Select bold font
ESC F
Cancel bold font
ESC G
Select double strike printing
Cancel double strike printing
Advance print position vertically
Select 60 dpi graphics
Select 120 dpi graphics
Select 12 cpi
ESC H
ESC J n
ESC K nL nH d1...dk
ESC L nL nH d1...dk
ESC M
ESC N n
ESC O
Set bottom margin
Cancel bottom margin
Select 10 cpi
ESC P
ESC Q n
Set right margin
Download from Www.Somanuals.com. All Manuals Search And Download.
72 Printer Control Codes
Standard Mode
ASCII Code
Function
ESC R n
n = 00
01
Select an international character set
#0
#1
U.S.A.
France
Germany
England
Denmark I
Sweden
Italy
02
#2
03
#3
04
#4
05
#5
06
#6
07
#7
Spain I
Japan
08
#8
09
#9
Norway
Denmark II
Spain II
Latin America
Korea
0A
#10
#11
#12
#13
#14
#64
0B
0C
0D
0E
Irish
Legal
40
ESC S n
n = 00
01
Select superscript/subscript printing
Superscript
Subscript
ESC T
Cancel superscript/subscript printing
ESC U n
n = 00
01
Turn unidirectional mode on/off
Unidirectional
Bi-directional
ESC W n
n = 00
01
Turn double width printing on/off
Turns off double-width
Turns on double-width
ESC Y nL nH d1...dk
ESC Z nL nH d1...dk
Select 120 dpi double speed graphics
Select 240 dpi graphics
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking system software settings in MS-DOS 73
Standard Mode
ASCII Code
Function
ESC [T 04 00 00 00 n1 n2 Select code page
n1 n2 = 01 B5
03 52
03 5C
03 5D
03 5F
03 61
03 62
0F 00
0F 01
0F 03
0F 04
0F 05
0F 06
0F 07
0F 08
03 54
03 E9
02 E1
03 53
03 65
03 A0
07 D1
03 04
03 06
0B B9
0B BA
0B C3
0B C4
0B CD
0B D7
0B E1
0F 0A
0F 14
0F 15
0F 17
0F 18
0F 19
#437
#850
USA
Multi-lingual
Portuguese
Icelandic
#860
#861
#863
Canadian French
Nordic
Russian
IBM-Russian
Gost
Polish
CS2
Hungarian
Turkish
#865
#866
#3840
#3841
#3843
#3844
#3845
#3846
#3847
#3848
#852
Brazil-ABNT
Brazil-ABICOMP
Latin-2
#1001
#737
Arabic
Greek #737
Greek #851
Greek #869
Greek #928
Lithuanian-KBL
Lithuanian #772
Lithuanian #774
Estonian-1
Estonian-2
Latvian-1
#851
#869
#928
#2001
#772
#774
#3001
#3002
#3011
#3012
#3021
#3031
#3041
#3850
#3860
#3861
#3863
#3864
#3865
Latvian-2
Bulgarian
Hebrew
Maltese
Standard KU
Rajvitee KU
Microwiz KU
STD 988 TIS
Popular TIS
Newsic TIS
ESC \ nL nH
ESC b m n1...nk 00
ESC g
Move relative horizontal print position
Set vertical tab in VFU channels
Select 15 cpi
ESC h n
n = 00
01
Select 1
×
1, 2
Cancels enlargement
Select double-high, double-wide (2
Select quadruple-high, quadruple-wide (4 4)
×
2, 4×4 sized printing
×2)
02
×
ESC j n
Advance reverse feed
ESC k n
n = 00
01
Select typeface
Roman
Sanserif
Courier
02
03
Prestige
OCR-B
Orator
05
07
Download from Www.Somanuals.com. All Manuals Search And Download.
74 Printer Control Codes
Standard Mode
ASCII Code
Function
ESC l n
Set left margin
ESC p n
n = 00
01
Turn proportional mode on/off
Returns to current fixed character pitch
Selects proportional spacing
ESC q n
n = 00
01
Select character style
Cancel shadow/outline printing
Set outline printing
02
Set shadow printing
Set shadow & outline printing
03
ESC r n
Select printer color
ESC t n
n = 00
01
Select character table
Select italic character table
Select code page table set by EDS Setting
Set download character in “00H-7FH” to “80H-FFH”
02
ESC w n
n = 00
01
Turn double high printing on/off
Turns on double-width
Turns off double-width
ESC x n
n = 00
01
Select LQ or Draft
Draft
LQ
ESC Z n
n = 00
01
Select HS-Draft or Draft
Draft
HS-Draft
FS 3 n
FS @
Set line spacing to n/360
″
Initialise printer
FS C n
n = 00
01
Select typeface
Roman
Sanserif
Courier
02
03
Prestige
OCR-B
Orator
05
07
FS E n
n = 00
01
Select double, triple width printing
Cancel expanded print (ESC W 0)
Select double-wide print (ESC W 1)
Select triple-wide print
02
FS F
FS I
FS R
Select forward feed
Select character table
Select reverse feed
FS V n
n = 00
01
Turn double high printing on/off
Cancel double-high mode
Select double-high mode
FS Z nL nH d1...dk
FS \ nL nH
Select 360 dpi graphics
Print characters from all character chart
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking system software settings in MS-DOS 75
Standard Mode
ASCII Code
Function
FS ^
DEL
Print a character from all character chart
Delete last character in buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
76 Printer Control Codes
IBM Mode
ASCII Code
Function
BEL
BS
Beeper
Backspace
HT
Tab horizontally
Line feed
LF
VT
Tab vertically
FF
Form feed
CR
Carriage return
Select double width printing (1 line)
Select condensed printing
Select printer
SO
SI
DC1
DC2
DC4
CAN
Select 10 cpi
Cancel double width printing (1 line)
Cancel line
ESC - n
n = 00
01
Turn under line on/off
Cancel underlining
Select underlining
ESC 0
ESC 1
ESC 2
ESC 3 n
ESC 4
Select 1/8
Select 7/72
Execute “ESC A” definition
Select n/216 or n/180 line spacing
″
line spacing
″
line spacing
″
″
Set top of form to the current position
ESC 5 n
n = 00
01
Turn automatic line feed on/off
Automatic line feeding stops
Automatic line feeding starts
ESC 6
Enable printing of upper control codes (Character Set #2)
Enable upper control codes (Character Set #1)
Select 12 cpi
ESC 7
ESC :
ESC A n
ESC B n1...nk 00
ESC C n
ESC C 0 n
ESC D n1...nk 00
ESC E
Define line spacing to n/72
″
Set vertical tab
Set page length in lines
Set page length in inches
Set horizontal tab
Select bold font
ESC F
Cancel bold font
ESC G
Select double strike printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking system software settings in MS-DOS 77
IBM Mode
ASCII Code
Function
ESC H
Cancel double strike printing
ESC I n
Select print pitch and download
Resident draft pica
n = 00
08
10
02
0A
12
03
04
0C
14
06
0E
16
07
Resident draft elite
Resident draft condensed
Default LQ pica
Default LQ elite
Default LQ condensed
Default LQ proportional
Download draft pica
Download draft elite
Download draft condensed
Download LQ pica
Download LQ elite
Download LQ condensed
Download LQ proportional
ESC J n
Advance print position vertically
Select 60 dpi graphics
Select 120 dpi graphics
Set bottom margin
ESC K nL nH d1...dk
ESC L nL nH d1...dk
ESC N n
ESC O
Cancel bottom margin
ESC P n
n = 00
01
Turn proportional mode on/off
Cancel proportional printing
Select proportional printing
ESC Q n
ESC R
Deselect printer
Set all tabs to power on defaults
ESC S n
n = 00
01
Select superscript/subscript printing
Select Superscript
Select Subscript
ESC T
Cancel superscript/subscript printing
ESC U n
n = 00
01
Turn unidirectional mode on/off
Select bi-directional mode
Select unidirectional mode
ESC W n
n = 00
01
Turn double width printing on/off
Cancel expanded print
Select expanded print
ESC X nL nH
Set left and right margins
ESC Y nL nH d1...dk
ESC Z nL nH d1...dk
ESC [@ nL nH m1...mk
Select 120 dpi double speed graphics
Select 240 dpi graphics
Control width, high and line spacing
Set initial condition
ESC [K nL nH init id p1
p2
Download from Www.Somanuals.com. All Manuals Search And Download.
78
IBM Mode
ASCII Code
Function
ESC [T 04 00 00 00 n1 n2 Select code page
n1 n2 = 01 B5
03 52
03 5C
03 5D
03 5F
03 61
03 62
0F 00
0F 01
0F 03
0F 04
0F 05
0F 06
0F 07
0F 08
03 54
03 E9
02 E1
03 53
03 65
03 A0
07 D1
03 04
03 06
0B B9
0B BA
0B C3
0B C4
0B CD
0B D7
0B E1
0F 0A
0F 14
0F 15
0F 17
0F 18
0F 19
#437
#850
USA
Multi-lingual
#860
Portuguese
Icelandic
Canadian French
Nordic
Russian
IBM-Russian
Gost
Polish
CS2
Hungarian
Turkish
#861
#863
#865
#866
#3840
#3841
#3843
#3844
#3845
#3846
#3847
#3848
#852
Brazil-ABNT
Brazil-ABICOMP
Latin-2
#1001
#737
Arabic
Greek #737
Greek #851
Greek #869
Greek #928
Lithuanian-KBL
Lithuanian #772
Lithuanian #774
Estonian-1
Estonian-2
Latvian-1
#851
#869
#928
#2001
#772
#774
#3001
#3002
#3011
#3012
#3021
#3031
#3041
#3850
#3860
#3861
#3863
#3864
#3865
Latvian-2
Bulgarian
Hebrew
Maltese
Standard KU
Rajvitee KU
Microwiz KU
STD 988 TIS
Popular TIS
Newsic TIS
ESC [\ nL nH m1 m2 m3 m4
ESC [g nL nH m d1...dk
ESC \ nL nH
Set base unit of line spacing
Select graphic mode
Print characters from all character chart
Reverse line feed
ESC ]
ESC ^
Print a character from all character chart
ESC _ n
n = 00
01
Turn over-score on/off
Cancel overscoring
Select overscoring
ESC d nL nH
ESC j
Move print position to the right
Stop printing
ESC r n
Select print color
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking system software settings in MS-DOS 79
Appendix F: Control Panel Operation Guide
A
B
C
SANSERIF
COURIER
PRESTIGE
ORATOR
D
E
F
ROMAN
LQ
1
2
3
10 CPI
12 CPI
15 CPI
4
5
6
COND
PROP
QUIET
POWER
ON LINE
DRAFT
HS-DRAFT
MICRO FEED
SET/EJECT
PARK
FONT
PITCH
FORM FEED
LINE FEED
EDS
BANK
SWITCH
STATUS
ON/OFF
PRINT
EXIT
Font Selection
Pitch Selection
Set/Eject/Park
Form Feed
Line Feed
Forward
On-Line
Panel Macro
Set TOF
Back ward
Micro Feed
Auto Loading Position Change Mode
Buffer Clear & All Reset
OFF-LINE
ON-LINE
Quiet Mode
Tear off (Long)
Tear off (Short)
Self Test
Off-Line
Font Lock
Pitch Lock
Multi-part Mode
Hex Dump Mode
Self Test
Font & Pitch Lock
EDS Mode
Dot-Adjustment Mode
POWER-ON
Bank
Left
Switch
Right
Status
Next
On/Off
Print
Exit
Exit
EDS MODE
DOT-ADJUSTMENT MODE
Paper Loading
Back ward
Forward
Cancel
Set
Save
Factory settings
AUTO LOADING POSITION CHANGE MODE
Note:
A dot means press and hold and an arrow means to just press. A dot and arrow
tied together means hold one while pressing the other.
Download from Www.Somanuals.com. All Manuals Search And Download.
Russian 60
selecting 30
Turkish 62
A
ASF 42
Auto LF
connecting
selecting 28
to a power outlet 8
to your computer 14
control panel
printer 16
control panel settings
saving 22
CR centering
setting 30
cut-sheet paper
ejecting 19
auto load position
changing 21
Auto Tear-off
selecting 28
AUTOEXEC.BAT 52
automatic sheet feeder 27, 42
B
bidirectional printing 28
buffered parallel interface cartridge 44
manual feeding 40
specifications 38
C
D
carton contents 2
character pitch
setting 18
dot alignment
adjusting 48
Character Set
international 57
standard italic 57
tables 57
download buffer 27
E
EDS Mode
Character Table
selecting 27
Code Page
auto LF with CR 28
auto tear-off 28
automatic sheet feeder 27
character set 30
character table 27
code page 30
CR centering 30
default settings 24
emulation 27
entering 24
exiting 26
graphics direction 28
line spacing 28
Multi-Part Mode 28
page length 30
Brazil-ABICOMP 62
Brazil-ABNT 62
Bulgarian 66
Canadian French 60
Estonian1 65
Estonian2 65
Greek 64
Hebrew 66
IBM-Russian 60
Latin-2 62
Latvian1 65
Latvian2 66
paper out detector 27
print mode 29
print pitch 29
printing switch settings 26
Quiet Print Mode 29
Lithuanian #772 64
Lithuanian #774 65
Lithuanian-KBL 64
Maltese 66
Nordic 60
Download from Www.Somanuals.com. All Manuals Search And Download.
RAM usage 27
selecting a bank 25
selecting a switch 25
settings 27
switch settings 25
using 24
line spacing
setting 28
LQ font
selecting 36
M
macro
zero style 28
eject 19
saving 22
Electronic DIP Switches 24
emulation 27
manual sheet feeding 40
micro feed 19
MS-DOS
F
setting up for printing 37
Multi-part Mode
entering 23
fanfold paper
form feed 19
parking 13, 19
printing on 12
specifications 37
tear-off function 13, 20
unparking 13
O
off-line
switching to 16
ON-LINE
indicator 16
on-line
switching to 16
options
font
selecting 17
Font Lock Mode
entering 17
form feed 19
automatic sheet feeder 42
buffered parallel interface cartridge
44
pull tractor unit 43
serial interface cartridge 43
serial-to-parallel converter 44
G
graphics direction
selecting 28
H
hexadecimal dump 46
P
page length
setting 30
I
initialization 23
input buffer 27
interface pin outs
paper
automatic feeding 40
fanfold 12
optional serial interface 56
parallel interface 56
international character set
selecting 30
handling 38
loading 9
micro feed 19
recommended print area 12
setting top of form 20
thickness adjustment 39
L
paper eject 19
line feed 19
Download from Www.Somanuals.com. All Manuals Search And Download.
paper guide
installing 7
standing up 8
paper jams 41
paper out detector 27
paper type
selecting 38
parallel cable 14
Pitch Lock Mode
entering 18
S
Self test 46
serial interface cartridge 43
serial-to-parallel converter 44
setup
printer 1
specifications
cut-sheet paper 38
fanfold paper 38
labels 39
platen knob
installing 4
printer 53
serial-to-parallel converter 45
port
system software settings
MS-DOS 52
parallel 14
print mode
T
selecting 29
tear-off function 13, 20
test print 46
print pitch
selecting 29
printer buffer
clearing 22
top of form
setting 20
printing
troubleshooting 46
guide 49
problem 49
problems
U
causes and solutions 49
excessive noise 50
hot printer case 50
incorrect characters 51
left margin movement 51
no printing 49
unidirectional printing 28
unpacking 2
V
voltage 2, 8
power supply 49
printing past paper edge 50
pull tractor unit 43
Z
zero style
selecting 28
Q
Quiet Print Mode 20
selecting 29
R
ribbon cartridge
installing 5
removing 7
taking up slack in 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Worldwide Headquarters
STAR MICRONICS CO., LTD.
536 Nanatsushinya, Shimizu,
Shizuoka, 424-0066, Japan
STAR MICRONICS ASIA LTD.
Rm 1802-6, 18/F., Tower 2, Enterprise Square
9 Sheung Yuet Road, Kowloon Bay Hong Kong
Tel: 852-2796-2727, Fax: 852-2799-9344
Download from Www.Somanuals.com. All Manuals Search And Download.
|