i.LINK INTERFACE BOARD
HKJ-101
INSTALLATION MANUAL
1st Edition
Download from Www.Somanuals.com. All Manuals Search And Download.
For the customers in the USA
For the customers in Europe
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.
This product with the CE marking complies with the EMC
Directive (89/336/EEC) issued by the Commission of the
European Community.
Compliance with this directive implies conformity to the
following European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment:
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors) and E4 (controlled EMC environment,
ex. TV studio).
Pour les clients européens
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
Ce produit portant la marque CE est conforme à la
Directive sur la compatibilité électromagnétique (EMC)
(89/336/CEE) émise par la Commission de la
Communauté Européenne.
La conformité à cette directive implique la conformité aux
normes européennes suivantes:
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with
the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.
• EN55103-1: Interférences électromagnétiques
(émission)
• EN55103-2: Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans
l’environnement électromagnétique suivant: E1
(résidentiel), E2 (commercial et industrie légère), E3
(urbain extérieur) et E4 (environnement EMC contrôlé ex.
studio de télévision).
The device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including ineterference that may cause undesired
operation.
Für Kunden in Europa
For customers in Canada
Dieses Produkt besitzt die CE-Kennzeichnung Und erfüllt
die EMV-Richtlinie (89/336/EWG) EG-Kommission.
Angewandte Normen:
This Class A digital apparatus complies with Canadian
ICES-003.
Pour les utilisateurs au Canada
Cet appareil numérique de la classe A est conforme à la
• EN55103-1: Elektromagnetische Verträglichkeit
(Störaussendung)
norme NMB-003 du Canada.
• EN55103-2: Elektromagnetische Verträglichkeit
(Störfestigkeit),
für die folgenden elektromagnetischen Umgebungen:
E1 (Wohnbereich), E2 (kommerzieller und in
beschränktem Maße industrieller Bereich), E3
(Stadtbereich im Freien) und E4 (kontrollierter EMV-
Bereich, z.B. Fernsehstudio)
HKJ-101
1 (P)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
Installation
1-1. Overview
The i.LINK interface board HKJ-101 enables the Digital Video Cassette Compact Player J-H1/J-H3 to
output the down-converted SD video signal in the i.LINK/DV format.
In addition, off-line editing can be executed by connecting the J-H1/J-H3 containing the HKJ-101 board
to the PC containing the non-linear editing software, using an i.LINK/DV cable.
HKJ-101 consists of the followings.
. DV-29 board :
. CN-2478 board :
1
1
. Rear panel for J-H1 : 1
. Rear panel for J-H3 : 1
Beside this Installation Manual, the following manuals are prepared for HKJ-101.
. Operation Manual CD-ROM (Supplied with J-H1/J-H3)
This manual is necessary for practical application and operation of J-H1/J-H3 and HKJ-101.
. Operation Guide (Supplied with J-H1/J-H3)
This manual serves as a quick reference.
. J-H Series Maintenance Manual (e-manual) (Available on request)
This manual describes the information that premises the component service (periodic inspection, ,
periodic maintenance, diagnostics, parts replacement, adjustments, parts list, block diagrams, schematic
diagrams, board layouts and others) to be used by system and maintenance engineers.
If this manual required, please contact your local Sony Sales Office/Service Center.
1-2. Installing the Circuit Board
Procedure is different when installing HKJ-101 in J-H1 and J-H3.
. To install HKJ-101 in J-H1 (Refer to Section 1-2-1.)
. To install HKJ-101 in J-H3 (Refer to Section 1-2-2.)
n
Before starting installation, be sure to turn off the POWER switch and disconnect the power cord. Then
start the following procedures.
HKJ-101
1-1 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2-1. To install HKJ-101 in J-H1
5. Insert the CN-2478 board to the second slot from the
bottom of J-H1.
1. Remove the six M3 case stopper screws.
2. Remove the rear panel.
n
6. Strongly push the connector panel both from the right
and the left sides of the CN-2478 board so that the
connector on the CN-2478 board is securely inserted
into the connector on the MB-993 board.
Store the removed rear panel in a safe place so as not
to lose it.
Rear panel
M3 case stopper
screws
CN-2478 board
M3 case stopper screws
7. Install the supplied rear panel for J-H1 using the six
M3 case stopper screws.
3. Insert the connector (CN601) on the DV-29 board into
the connector (CN41) on the CN-2478 board.
n
n
Tighten the screws in the state that the two dowels are
aligned with the holes (a) and (b) on the rear panel as
shown in the figure.
First, insert the connector (CN401) on the DV-29
board to the hole for i.LINK connector on the IF panel.
Then insert connector (CN601) to the connector on the
CN-2478 board.
Dowel
M3 case stopper
screws
4. Fix the DV-29 board to the IF panel and to the CN-
2478 board using the supplied screws (PWH2 x 5 : 2
screws, PSW2.6 x 5 : 3 screws).
n
When tightening the screws, tighten the screws PWH2
Hole (b)
x 5 first of all screws.
DV-29 board
CN401
Dowel
M3 case stopper
screws
Hole (a)
M3 case stopper
screws
J-H1 rear panel
(Supplied accessory)
CN601
IF panel
PWH2 x 5
CN41
PSW2.6 x 5
CN-2478 board
PSW2.6 x 5
HKJ-101
1-2 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2-2. To install HKJ-101 in J-H3
4. Insert the connector (CN601) on the DV-29 board into
the connector (CN41) on the SDI-80 assembly.
n
1. Remove the six M3 case stopper screws.
2. Remove the rear panel.
n
First, insert the connector (CN401) on the DV-29
board to the hole for i.LINK connector on the IF panel.
Then insert connector (CN601) to the connector on the
CN-2478 board.
Store the removed rear panel in a safe place so as not
to lose it.
5. Fix the DV-29 board to the IF panel and to the SDI-80
assembly using the supplied screws (PWH2 x 5 : 2
screws, PSW2.6 x 5 : 3 screws).
Rear panel
n
When tightening the screws, tighten the screws PWH2
x 5 first of all screws.
DV-29 board
CN401
M3 case stopper
screws
CN601
M3 case stopper screws
IF panel
PWH2 x 5
CN41
3. Pull out the SDI-80 assembly from the second slot
from the bottom of the J-H3 in the direction of the
arrow.
PSW2.6 x 5
SDI-80 assembly
PSW2.6 x 5
6. Insert the SDI-80 assembly to the original slot.
7. Strongly push the connector panel both from the right
and the left sides of the SDI-80 assembly so that the
connector on the SDI-80 assembly is securely inserted
into the connector on the MB-993 board.
SDI-80 assembly
SDI-80 assembly
HKJ-101
1-3 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Install the supplied rear panel for J-H3 using the six
M3 case stopper screws .
n
Tighten the screws in the state that the two dowels are
aligned with the holes (a) and (b) on the rear panel as
shown in the figure.
Dowel
M3 case stopper
screws
Hole (b)
Dowel
M3 case stopper
screws
Hole (a)
J-H3 rear panel
(Supplied accessory)
M3 case stopper
screws
HKJ-101
1-4 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen
Ausrüstung
ohne
ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
HKJ-101
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Japan
2003. 7 16
©2003
Sony Corporation
HKJ-101 (SY) J, E
3-805-991-01
B&P Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|