Instruction Manual
SCPH-75002
SCPH-75003
Before using this product, carefully read this manual and retain it for future reference.
2-650-066-22(1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Table of contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Health
• Stop using the console immediately if you experience any of the following
symptoms. If the condition persists, consult a doctor.
– Lightheadedness, nausea, or a sensation similar to motion sickness
– Tired, uncomfortable or aching hands or arms
– Tired, dry or aching eyes
• When operating the unit, play in a well-lit room and keep a safe distance from the
TV screen.
Precautions
This product has been designed with the highest concern for safety. However, any
electrical device, if used improperly, has the potential for causing fire, electrical
shock or personal injury. To help ensure accident-free operation, follow these
guidelines:
• Avoid prolonged use of the console. Take a break of about 15 minutes during every
hour of play.
• Observe all warnings, precautions and instructions.
• Stop use and unplug the AC power cord from the electrical outlet immediately if
the device functions in an abnormal manner or produces unusual sounds or smells.
• Contact the appropriate PlayStation® customer service helpline which can be
found within every PlayStation® and PlayStation®2 format software manual if the
device does not operate properly.
• Do not use the console when you are tired or short of sleep.
• Listening to sound continuously for a long time with a high volume may adversely
affect the ears. Be careful especially when using headphones. Adjust the volume
so that surrounding sounds can be heard.
Safety
• Do not remove the console exterior or disassemble the console. The laser beam
emitted from the lens of this unit may be harmful to the eyes.
• Do not use the console near water.
• Keep the console and all connecting cords and cables out of the reach of children.
• Do not touch the plug of the AC power cord with wet hands.
• Do not touch the console or connected accessories during an electrical storm.
• Do not touch the console or AC adaptor for extended periods of time while the
console is turned on as extended contact may cause low-temperature burns.
• Do not place the console and connected accessories on the floor or in a place where
they may cause persons walking by to trip or stumble.
• Adjust the settings of the DVD player according to the instructions provided before
playing a DVD. If the settings are not correct, a loud sound may be emitted,
possibly injuring your ears or damaging the speakers.
• Do not touch a disc while it is spinning as personal injury or damage to the disc
may result.
• Do not close the disc cover in a way that could pinch your hand or fingers as
personal injury or damage to the console may result.
Precautions
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Use and handling
AC adaptor and AC power cord use
• Do not throw or drop the console or accessories, or expose them to strong physical
shock.
• Do not place the console or accessories on surfaces that are unstable, tilted or
subject to vibration.
• To help ensure safe operation, regularly inspect the AC adaptor and AC power
cord. If damaged, stop use immediately and contact the appropriate PlayStation®
customer service helpline which can be found within every PlayStation® and
PlayStation®2 format software manual.
• Do not expose the console or accessories to high temperatures, high humidity or
direct sunlight (use in an environment where temperatures range from 5 °C to
35 °C).
• Do not place the console or accessories in locations subject to sudden temperature
change (for example, changes of 10 °C per hour or more).
• Do not leave the console or accessories in a car with its windows closed
(particularly in summer).
• Do not place the console in locations of poor ventilation such as small, enclosed
areas, directly against a wall or on a thick carpet or bedding.
• Do not expose the console to dust, smoke or steam. This can cause the console to
malfunction.
• Do not use a power cord other than the supplied AC adaptor and AC power cord.
• Check that there is no dust or lint on the power plug before inserting into an
electrical outlet. If the plug becomes dirty, wipe it off with a dry cloth before
connecting.
• Unplug the AC power cord from the electrical outlet before cleaning or moving the
console, or when you do not intend to use the console for an extended period of
time. When disconnecting, grasp the power cord by the plug and pull straight out
of the electrical socket. Never pull by the cord and do not pull out at an angle.
• Do not connect the AC adaptor and/or AC power cord to a voltage transformer or
inverter.
Notes on safety when using the Analog Controller
(DUALSHOCK®2)*
• Stop using the console immediately if you begin to feel tired or if you experience
discomfort or pain in your hands or arms while operating the Analog Controller
(DUALSHOCK®2). If the condition persists, consult a doctor.
• The Analog Controller (DUALSHOCK®2) is intended for use with the hands only.
Do not bring it into contact with your head, face or the bones of any other part of
the body.
• The vibration function of the Analog Controller (DUALSHOCK®2) can aggravate
injuries. Do not use the vibration function if you have any ailment or injury to the
bones, joints or muscles of your hands or arms. Note that some PlayStation®2 and
PlayStation® format software titles set the vibration function to "On" by default. In
most cases, the vibration function can be set to "Off" in the options menu of the
software. Do not play such titles using the Analog Controller (DUALSHOCK®2)
unless you have set the vibration function to "Off".
• Do not allow liquid or small particles to get into the console.
• Do not put any objects on the console.
• Do not touch or insert foreign objects into the connectors of the console or
accessories.
• Do not place the console close to magnetic fields produced by magnets or
loudspeakers.
• Do not set the console other than in the vertical or horizontal position. When
placing in the vertical position, use the Vertical Stand (for PlayStation®2) (sold
separately) that is compatible with this console. Also, do not change the position
while the console is turned on.
• Avoid prolonged use of the Analog Controller (DUALSHOCK®2). Take a break
at about 30-minute intervals.
*
These notes also apply to other controllers.
Precautions
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with a network cable
Moisture condensation
Do not connect network cables or telephone cords of the following types to the
network connector:
• Standard residential telephone lines
• Network cables not appropriate for use with a 10Base-T/100Base-TX network
• Any ISDN (digital) compatible phone or data line
• PBX phone lines
If the console or disc is brought directly from a cold location to a warm one, moisture
may condense on the lens inside the console or on the disc. Should this occur, the
console may not operate properly. In this case, remove the disc and turn off and
unplug the console. Do not put the disc back in until the moisture evaporates (this
may take several hours). If the console still does not operate properly, contact the
appropriate PlayStation® customer service helpline which can be found within every
PlayStation® and PlayStation®2 format software manual.
• Other "unknown" types of telephone lines
Disc handling
Cleaning
• Do not touch the disc surface when handling a disc; hold it by the edges.
• Do not stick paper or tape onto discs and do not write on discs.
• Fingerprints, dust, dirt or scratches on the disc can distort the picture or reduce
sound quality. Always handle carefully and make sure discs are clean before use.
• Do not leave discs near a heat source, in direct sunlight or in high humidity.
• Store discs in their cases when not in use - scratched and damaged discs will not
function correctly.
• For safety reasons, before cleaning the console or connected accessories, 1) turn
off the console, 2) disconnect the power plug for the console from the electrical
outlet, and 3) remove the network cable from the network connector.
• When cleaning the console, use a soft, dry cloth. Do not use paint thinner, solvents,
other chemicals or a chemically-treated dust cloth to clean the product.
• When dust accumulates in the console vents, remove the dust with a low-powered
vacuum cleaner.
• Clean discs using a soft cloth, lightly wiping from the centre outwards.
Do not use solvents such as benzine, commercially available cleaners not intended
for CDs or anti-static spray intended for vinyl LPs.
• Do not leave a disc in the console when moving or changing the position of the
console.
• Do not touch the lens located inside the disc cover. To help protect the lens from
dust, keep the disc cover closed except when inserting or removing discs.
Exterior protection
To help prevent damage to the painted parts, follow the precautions below:
• Do not spill liquids such as alcohol, benzine, paint thinner or other chemicals on
the product.
• Do not use irregularly shaped discs (for example, heart- or star-shaped discs) or
damaged, re-shaped or repaired discs.
• Do not place any rubber, vinyl or plastic items on the painted surfaces for an
extended period of time.
Never disassemble the console or supplied accessories
Use the PlayStation®2 console and accessories according to the instructions in this
manual. No authorisation for the analysis or modification of the console, or the
analysis and use of its circuit configurations, is provided. There are no user-
serviceable components inside the PlayStation®2 console. Disassembling the
console will void the guarantee. Additionally, there is a risk of exposure to laser
radiation as well as to electrical shock hazards.
When connecting the console to a plasma or projection* TV
Do not leave a still image on the TV screen for an extended period of time, as this
may leave a faint image permanently on the screen.
*
Except LCD screen types
Precautions
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Positioning the console
Getting started
You can place the console in either the horizontal or vertical position.
Horizontal position
Set the console horizontally.
Checking the package contents
Vertical position
Check that you have all of the following items. If any items are missing,
contact the appropriate PlayStation® customer service helpline which can
be found within every PlayStation® and PlayStation®2 format software
manual.
When setting the console in the vertical
position, use the SCPH-70110 E Vertical
Stand (for PlayStation®2) (sold separately).
s PlayStation®2 console...1
s Analog Controller
(DUALSHOCK®2)...1
Note
Some Vertical Stands (for PlayStation®2) cannot be used with this model of the
PlayStation®2 console (
Vertical Stand.
page 46). Choose the SCPH-70110 E when purchasing a
s AC adaptor...1
s AV Cable (integrated
audio/video)...1
s AC power cord...1
s Euro-AV connector plug
(supplied with SCPH-75003)...1
(supplied with SCPH-75002)
s Instruction Manual...1
(supplied with SCPH-75003)
Getting started
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Part names
Do not place the console in locations where it may be exposed to the following
conditions:
• Places subject to excessive cigarette smoke or dust. Cigarette smoke residue
or dust build-up on the internal components, such as the lens, may cause the
console to malfunction.
PlayStation®2 console front
• Places subject to extreme temperatures, in direct sunlight, near a heat source,
or in a car with its windows closed (particularly in summer). These conditions
may warp the exterior of the console or cause the console to malfunction.
• Places close to magnetic fields, such as those produced by magnets or
loudspeakers.
Disc cover
]/1 (on/standby) indicator
A (open) button
]/1 (on/standby)/RESET button
• Places subject to vibration.
MEMORY CARD slot 2
MEMORY CARD slot 1
"
" product family logo*
RESET
IR receiver
Front vent
Controller port 1
Controller port 2
USB connector
* The "
" product family logo can be rotated to match the horizontal or vertical
positioning of the console.
Note
You can connect USB devices that are compatible with the PlayStation®2 console.
Note, however, that not all USB-compatible products work with the PlayStation®2
console. Refer to the instructions supplied with the device to be connected for more
information.
Part names
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PlayStation®2 console rear
Connecting to a TV
Rear vent
Before connecting
• Do not plug the AC power cord for the console into the electrical outlet
until you have made all other connections.
!DC IN8.5V
connector
• Check that the TV is turned off.
NETWORK connector
Connecting to a TV using the supplied AV Cable
DIGITAL OUT (OPTICAL)
connector
AV MULTI OUT connector
Connect the console to the TV as shown below.
Console rear
Note
For part names of the Analog Controller (DUALSHOCK®2), see "Using the Analog
Audio and video inputs of the TV
VIDEO
L-AUDIO-R
Yellow White
Red
To the AV MULTI
OUT connector
Do not use when
connecting to a
monaural TV.
AV Cable (integrated audio/video)
Connecting to a TV
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a TV with a Euro-AV connector
using the Euro-AV connector plug (SCPH-75003)
Caution
If you display a still image on a plasma or projection* TV screen for an extended
period of time, "ghosting" may occur. This is a characteristic of these types of
TVs. Static, non-moving images, such as console setting menus, DVD menus or
paused images, may leave a faint image permanently on the TV screen if left on
for an extended time. Refer to the instructions supplied with your TV for details.
* Except those of LCD screen types
Connect your PlayStation®2 console to the Euro-AV connector (SCART)
on the TV using the Euro-AV connector plug and AV Cable (integrated
audio/video), making sure you match the colour-coded plugs of the AV
Cable to the matching jacks of the connector plug.
Console rear
Note
The console can be connected to a VCR or an integrated TV/VCR. Note, however,
that if you play a DVD with copy-protection encryption, picture quality may be
reduced.
Euro-AV
connector plug
To AV MULTI
OUT connector
To Euro-AV
connector
AV Cable (integrated audio/video)
After connecting
Set your TV to the appropriate video input mode. Refer to the Instruction
Manual of your TV.
Connecting to a TV
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
When using cables sold separately
• The DVD player's progressive scan mode is only available when playing a disc
recorded in NTSC format, and viewed on a TV that supports progressive scan
(480p).
Picture quality differs depending on the type of cable used. Use the
information below to determine the best connection method.
If you use a cable sold separately, refer to the instructions supplied with the
cable.
• You cannot connect the console to a TV with component video inputs that are
exclusively for HDTV use (Y PB PR). Refer to the instructions supplied with your
TV for details.
TV
Cable type
A TV with S VIDEO inputs
A TV without video inputs
S VIDEO Cable (SCPH-10060 E)
RFU Adaptor (SCPH-10072 C)
(for SCPH-75002)
RFU Adaptor (SCPH-10072 B)
(for SCPH-75003)
A TV with Euro-AV (SCART) Euro-AV Cable (SCPH-10142)
connector
(for SCPH-75003)
A TV with component video
input connectors
Component AV Cable (for PlayStation®2)
(SCPH-10100 E)
Picture quality scale
High quality
x AV Cable (supplied) x S VIDEO Cable x Component AV Cable
x RFU Adaptor
This scale is intended only as a reference. Depending on the product or
condition of your TV, the picture quality may be different.
When using the Euro-AV Cable, picture quality may vary depending on your
TV's AV connection.
For optimum picture quality, connect your Euro-AV cable to an RGB-
compatible socket on your TV. Refer to the instructions supplied with your TV
for details.
Connecting to a TV
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting digital audio
equipment
Connecting the controller
1 Insert the Analog Controller (DUALSHOCK®2) into a controller
port of the console.
By using a commercially available optical digital cable, you can enjoy
surround sound with the effect of being in a movie theatre or a concert hall.
When connecting the console to audio equipment with digital connectors,
refer to the instructions supplied with the device to be connected.
Console front
MEMORY CARD
Console rear
Connected device
DIGITAL IN
OPTICAL
Analog Controller
(DUALSHOCK®2)
Commercially available optical
digital cable
Note
Some software titles designate a specific controller port to be used. Refer to the
instructions supplied with the software for details.
Notes
• If you connect the console to audio equipment using an optical digital cable, it may
affect the audio output of some PlayStation®2 format software with the result that
no sound is produced. If this happens, use a cable such as the supplied AV Cable
(integrated audio/video) and connect it to the console's AV MULTI OUT
connector. Do not use an optical digital cable.
• After connecting digital audio equipment, set "Digital Out (Optical)" to "On" in the
System Configuration menu. For details, see "Digital Out (Optical)" (
Connecting digital audio equipment
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Plug the AC power cord into the electrical outlet.
Connecting the AC adaptor and
AC power cord
Console rear
Warnings
AC power cord
• The socket-outlet shall be installed near the equipment and shall be easily
To the electrical outlet
accessible.
• Do not plug the AC power cord for the console into the electrical outlet until
you have made all other connections.
Some regions and countries may
use a different electrical outlet
plug from the one illustrated.
1 Connect the AC power cord to the AC adaptor.
The =/1 (on/standby) indicator on the console front will light up in red
to indicate that the console is in standby mode.
AC adaptor
AC power cord
RESET
]/1 indicator
Console front
2 Plug the connector of the AC adaptor into the ! DC IN 8.5V
connector on the console rear.
Console rear
! DC IN 8.5V connector
AC adaptor
Connecting the AC adaptor and AC power cord
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• The first time you turn on the console after purchase, screens for setting
"Language", "Time Zone" and "Daylight Savings Time (Summer Time)" will be
displayed. Follow the on-screen instructions to complete the settings.
Turning the console on and off
• If you connect the console to a wide-screen TV, set "Screen Size" in the System
Configuration menu (
Before turning on the console
Do not turn on the console until you have finished these steps. Refer to the
instructions supplied with your TV for details.
• Turn on the TV.
Turning off the console
1 Press and hold the =/1/RESET button on the console front for
• Change your TV setting to display output from the line to which the
console is connected.
more than a second.
The =/1 indicator will turn red to indicate that the console has entered
standby mode.
Turning on the console
=/1/RESET button
RESET
1 Check that the =/1 (on/standby) indicator on the console
Console front
front is lit up in red.
=/1 indicator
2 Press the =/1 (on/standby)/RESET button on the console
front.
The =/1 indicator on the console front will turn green and output from
the console will be displayed on the TV.
Warning
The power is not completely turned off when the console is in standby mode. If
you do not plan to use the console for an extended period of time, unplug the
AC power cord from the electrical outlet.
=/1/RESET button
RESET
Console front
=/1 indicator
Turning the console on and off
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Games
Playing a game
Place the disc in the console with the label
side facing up.
Disc cover
Place the disc so that all three tabs
are above the disc's surface.
A (open) button
=/1/RESET button
Before playing a game
Starting a game
Check that the connections to the TV and audio equipment are correct and
that the precautions have been met.
2 Press the A (open) button on the console front.
The disc cover opens.
3 Place the disc in the console.
Note
Set the disc in the disc holder with the label side facing up.
To play online games, you first need to connect to and set up a network. See
"Connecting to a network" (
page 42) for details.
Playing a game
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Close the disc cover.
2 Remove the disc.
Push the middle of the disc cover. After the disc cover is closed, the
game will start.
Hold down the black centre part of the disc holder, and then lift the
disc by the edges.
Push the middle of the disc cover.
Press the black centre part
of the disc holder.
Notes
3 Close the disc cover.
• You can also start a game from the Browser screen (
page 35).
• If you turn on the console after inserting a disc, the game will start automatically.
4 Press the =/1/RESET button.
To reset a game
Press the \/1 (on/standby)/RESET button on the console front. Do not
accidentally press the @/1/RESET button while playing a game, as doing
so will cause the game to reset.
Changing game discs
1 Open the disc cover and remove the disc.
When removing a disc, hold down the black centre part of the disc
holder and then lift the disc by the edges.
Ending a game
2 Insert a new disc.
Caution
3 Close the disc cover and reset the console.
When removing a disc, check that the disc has stopped completely. Do not touch
the disc if it is spinning, as doing so may cause injury, damage to the disc or
console malfunction.
The new game will start.
Note
1 Press the A button on the console front.
You do not need to turn off the console when changing games.
Playing a game
16
Download from Www.Somanuals.com. All Manuals Search And Download.
About mode switching
Using the Analog Controller (DUALSHOCK®2)
The ANALOG mode button can be used to switch between two modes.
Switch to the appropriate mode for use. Note, however, that some software
titles make this adjustment automatically.
The Analog Controller (DUALSHOCK®2) is equipped with a pressure-
sensitive button function. It also has a vibration function.
Digital mode
(indicator: off)
Analog mode
(indicator: red)
Part names
SELECT button
L2 button
START button
R2 button
Notes
L1 button
R1 button
button
• When using the Analog Controller in digital mode, the left and right analog sticks
do not function. Also, the pressure-sensitive button function is turned off.
• Depending on the software, you may not be able to switch modes even if you press
the ANALOG mode button.
Directional
buttons
button
button
button
About analog controls
• When playing a PlayStation®2 format software title, you can use all
buttons in analog mode except for the START, SELECT, L3 and R3
buttons.
• When playing a PlayStation® format software title, only the left and right
analog sticks can be used in analog mode.
Right analog stick/ R3 button*
Mode indicator
Left analog stick/ L3 button*
ANALOG mode button
* The left and right analog sticks, or the L3 and R3 buttons, function only in analog
mode (indicator: red).
Note
Depending on the software, the buttons for use in analog mode may be limited. Refer
to the instructions supplied with the software for details.
* The L3 and R3 buttons function when the analog sticks are pressed.
Note
About the vibration function
Before using the Analog Controller
The vibration function can be set to ON or OFF in the software options
menu.
(DUALSHOCK®2), with the console turned on,
rotate the left and right analog sticks once with your
thumbs before starting a game. Do not twist the
analog sticks, but rotate as if drawing a circle as
shown in the diagram.
Note
Depending on the software, the vibration function may be set to "On" automatically.
Playing a game
17
Download from Www.Somanuals.com. All Manuals Search And Download.
About using the Analog Controller (DUALSHOCK®)
(SCPH-110 E)
Using Memory Cards
You can use the Analog Controller (DUALSHOCK®) (SCPH-110 E) with
the PlayStation®2 console, but the functions of the buttons in analog mode
may be different from those of the Analog Controller (DUALSHOCK®2).
Only the left and right analog sticks can be used in analog mode.
You can save and load game data using a Memory Card. You can also
delete game data or copy game data from one Memory Card to another.
About Memory Card types
Note
There are two types of Memory Cards. Select a Memory Card suitable for
the software in use.
Not all PlayStation®2 format software titles support the use of the Analog Controller
(DUALSHOCK®) (SCPH-110 E). The Analog Controller (DUALSHOCK®2)
should be used in such cases.
Memory Card type Compatible software
Amount of memory
Memory Card (8MB) PlayStation®2 format
Approx. 8 MB
(for PlayStation®2)
(SCPH-10020 E)
software
Memory Card
PlayStation® format
software
15 memory blocks
(approx. 120 KB)
(SCPH-1020 E)
Note
The Memory Card (8MB) (for PlayStation®2) uses "MagicGate", a technology that
helps protect copyrighted content through data encryption and hardware
authentication.
is a term of copyright protection technology developed
by Sony Group.
does not guarantee compatibility with other products
bearing the "MagicGate" trademark.
Using Memory Cards
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Select "Copy" or "Delete", and then press the
button.
Inserting a Memory Card
When copying game data, check that two Memory Cards are inserted
in the console. If you have selected "Delete", skip to step 5.
Insert the Memory Card into a MEMORY CARD slot on the console front.
Console front
4 Select the destination, and then press the
5 Select "Yes", and then press the button.
button.
MEMORY CARD
While copying or deleting data, do not remove the Memory Cards.
6 When copying or deleting is completed, press the
button.
Note
Notes
Some software titles designate a specific MEMORY CARD slot to use. Refer to the
instructions supplied with the software for details.
• To view information about a game data item, select the icon for the data and then
press the
button to check the details.
• Compatibility between software and Memory Cards:
– You cannot save or copy PlayStation®2 format software to a Memory Card
(SCPH-1020 E).
Saving or loading game data
– You cannot save PlayStation® format game data to a Memory Card (8MB) (for
PlayStation®2). You can, however, copy PlayStation® format game data from a
Memory Card (SCPH-1020 E) to a Memory Card (8MB) (for PlayStation®2) for
storage purposes. Note that such game data cannot be loaded directly from a
Memory Card (8MB) (for PlayStation®2).
Depending on the software, the procedure for saving or loading may vary.
Refer to the instructions supplied with the software for details.
Copying or deleting game data
buttons to select the icon for the Memory Card you want to
use for copying or deleting data and then press the
button.
2 Select the icon for the data you want to copy or delete, and
then press the
button.
Using Memory Cards
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio CDs
Operating the CD player during playback
Playing an audio CD
Using the directional buttons, select the icon for the desired track and then
press the
button.
Icon (button*)
Function
Playing a CD
. (L1 button)
Go to the beginning of the current or previous track
Fast reverse
m
M
(L2 button)
(R2 button)
Follow steps 1 to 4 of "Starting a game".
Fast forward
The track numbers are displayed.
> (R1 button)
Go to the beginning of the next track
2 Using the directional buttons, select the track number you
N
X
(START button) Start playback
(START button) Pause playback
(SELECT button) Stop playback
want to play and then press the
button.
Playback begins.
x
Notes
* You can operate directly by pressing the buttons of the Analog Controller
(DUALSHOCK®2).
• If you turn on the console after inserting a disc, the track numbers are displayed
automatically.
• You can also start playback from the Browser screen (
Note
You can also use the DVD Remote Control (for PlayStation®2) (sold separately).
Caution
To play an audio CD recorded in DTS format, you must connect a device with
Note that an extremely loud noise may be emitted if the device does not have a
DTS decoder or if it is connected to the AV MULTI OUT connector.
Ending audio CD playback
1 Using the directional buttons, select x and then press the
button.
Playback stops. Press the A (open) button on the console front to
remove the disc.
Playing an audio CD
20
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Select the audio CD icon, and then press the
button.
Playing in various modes
The track numbers are displayed, and the setting option is shown in the
lower left of the screen.
You can set for "Play Mode" and "Repeat".
6 Select the desired track, and then press the
button.
Play Mode Normal
Program
Plays tracks as recorded on the CD
Playback begins.
Plays tracks in a specified order
Plays tracks in a random order
Does not play the CD repeatedly
Plays all tracks repeatedly
Shuffle
Notes
• You can also access the Play Options screen from the screen displaying the tracks
by selecting the Audio CD icon in the upper left corner of the screen and pressing
Repeat
Off
All
1
the
button.
• You can set "Play Mode" and "Repeat" at the same time.
Plays a track repeatedly
buttons to select the audio CD icon and then press the
button.
The Play Options screen is displayed.
2 Select "Play Mode" or "Repeat", and then press the
button.
3 Select the desired setting, and then press the
button.
If you select "Program", the screen for specifying track order will be
displayed. Select the tracks you want to play.
4 Press the
button.
The Browser screen is displayed.
Playing an audio CD
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDs
Using the Control Panel
Watching a DVD
2 Press the SELECT button.
You can operate the DVD player using the following methods.
• Using the on-screen Control Panel
• Operating directly using the Analog Controller (DUALSHOCK®2)
• Using the DVD Remote Control (for PlayStation®2) (sold separately)
The Control Panel is displayed. If you press the SELECT button again,
the display will change its position on the screen.
The following instructions assume use of the Control Panel to operate the
DVD player. Some operations may be different depending on the method
used.
Notes
• For details about playing a DVD, refer to the instructions supplied with the DVD.
• The PlayStation®2 console plays disc content as recorded in the DVD software.
Note that not all features are available on all DVDs.
3 Using the directional buttons, select an icon and then press
the
button.
Note
To turn off the Control Panel, press the SELECT button (once or twice), or press the
button.
Control Panel item list
You can access the following options in the Control Panel.
Icon
Function
Menu
Displays the DVD-Video menu
Top Menu
Displays the DVD-Video menu
Watching a DVD
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Icon
Function
Icon
N
X
Function
Returns to the previously selected screen
within the DVD's menu
Play
Starts playback
Return
O
Pause
Stop
Pauses playback
Stops playback (
Displays and changes audio options on
DVDs with multiple audio tracks
Audio Options
Angle Options
Subtitle Options
x
Displays and changes viewing angles on
DVDs recorded with multi-angle options
Specifies a scene for playback, and starts
playback of the scene that has been set
A-B Repeat
Displays and changes subtitle options on
DVDs with subtitle options
(
Begins playback of titles or chapters in a
Shuffle Play
Program Play
Skips to the selected title, chapter or the
specified time, and starts playback
Go To
(
Begins playback of titles or chapters in a
Displays and changes options for
Setup
language, picture quality, Parental Control
Selects repeated playback of all the titles
on the disc, or one title or one chapter
level, audio, etc. (
Repeat Play
(
Displays the current title or chapter
number, the elapsed time, etc.
Time Display
For DVD-RW discs (VR mode), selects
(
Original/Play List Original or Play List content to play
(
Displays the direct button functions of the
Analog Controller (DUALSHOCK®2)
Help
Clears selected numbers or playback
Clear
Used to enter the number of a chapter you
Go to Chapter
Previous/Next
0~9
want to play (
Notes
Returns/skips to the beginning of the
current, previous or next chapter
• You can use " " to check the options that can be accessed directly using the
buttons of the Analog Controller. To access the options directly using the
controller, you must clear the Control Panel from the screen.
• Depending on the playback mode, some options may not be available or cannot be
adjusted.
./>
Fast reverses/forwards playback on the
screen to help you find a particular scene
/
/
Search
Slow
(
Changes to playback/reverse playback in
slow-motion
Watching a DVD
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a DVD
Selecting a specific scene for playback
Selecting a scene by chapter number
1 During playback, select the desired chapter number in the
button.
Notes
Playback of the selected chapter begins. If you want to play a chapter
with a single digit number (i.e. 1-9), enter a leading zero. For example,
enter as "01".
• If you turn on the console after inserting a disc, playback will begin automatically.
• You can also start playback from the Browser screen (
Selecting a scene by title number, chapter number or by
specifying the time
Ending DVD playback x
1 During playback, select
in the Control Panel
and then press the button.
(
Playback stops. Press the A (open) button on the console front, and
then remove the disc.
2 Select an item, and then press the
button.
Title
Specifies the title number
Playing a DVD from the last stopping point
(Resume Play)
Chapter
Specifies the chapter number
C XX:XX:XX
(or T XX:XX:XX)
Specifies the elapsed time for the chapter (or title)
and then press the
button.
2 Select N, and then press the
button.
3 Select the numbers for the desired scene, and then press the
Playback begins from the point where you stopped the disc in step 1.
button.
Playback of the selected chapter begins.
To clear Resume Play
After step 1, select x and then press the
button.
Watching a DVD
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding a particular point on a DVD (Search)
Displaying playback information
You can display information such as the current title number or elapsed
time.
You can search either forwards or backwards to quickly locate a particular
point on a DVD.
1 During playback, select
in the Control Panel
(
1 During playback, select
or
in the Control Panel
button.
The display changes as shown below each time you press the
button.
(
page 22) and then press and hold the
Search speed changes as shown below when you press either the up or
down directional button while holding down the
button.
Title X Chapter X
Title X Chapter X
Title number and chapter number
• Search 3
• Search 2
• Search 1
• Slow
C
XX:XX:XX Elapsed time of current chapter
Title X Chapter X C - XX:XX:XX Remaining time of current chapter
Title X Chapter X XX:XX:XX Elapsed time of current title
T
2 Release the
searching for.
button when you reach the point you are
Title X Chapter X T - XX:XX:XX Remaining time of current title
(Off)
Playback returns to normal speed.
Note
To use the Analog Controller to Search during playback, press and hold down the L2
or R2 button to begin searching. Use the directional buttons to change speeds.
Release the L2 or R2 button when you reach the point you are searching for.
Watching a DVD
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Original or Play List for DVD-RW
playback
Using the playback modes
When using a DVD-RW disc (VR mode), you can select the type of titles
you want to play.
Using the various playback modes, you can play titles or chapters in the
order you want or repeat playback of a specific scene. There are four
playback modes:
1 With playback stopped, select
page 22) and then press the
in the Control Panel
button.
(
Original and Play List will be selected in turn each time you press the
button.
Original
Plays content in the originally recorded sequence
Plays edited content. Play List is the default setting.
to operate the DVD player.
Play List
Notes
Notes
• Slow-motion play in reverse is not available for DVD-RW discs (VR mode).
• You can play combinations of Program Play, Shuffle Play, and Repeat Play. Note,
however, that some Shuffle Play or Repeat Play options may not be available
depending on the combination.
• You cannot use this function with Resume Play. Clear Resume Play (
before selecting this feature.
• The PlayStation®2 console plays disc content as recorded in the DVD software.
Program Play
You can create programmes to play titles and chapters in any order.
1 During playback, select
in the Control Panel
button.
(
page 22) and then press the
2 Select a programme number, and then press the
button.
If no programmes have been set, the only option will be "1. Title".
3 Select the title number, and then press the
button.
Using the playback modes
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select the chapter number, and then press the
button.
Repeat Play
To play all the chapters, select "All". Repeat steps 2 to 4 to set other
titles or chapters.
You can set this option to play titles or chapters repeatedly.
1 Select
press the
button.
5 Press the START button.
Program Play begins.
The display changes as shown below each time you press the
button.
Note
z
The setting will not be cleared after Program Play finishes.
Disc Repeat
Title Repeat
Repeats playback of all titles
Repeats playback of one title
Shuffle Play
Chapter Repeat Repeats playback of one chapter
Repeat Off Clears Repeat Play
You can set this option for random playback of all titles or chapters
recorded on a disc. Playback order will be different each time Shuffle Play
is used.
2 Select N, and then press the
button.
1 Select
press the
button.
The display changes as shown below each time you press the
button.
A-B Repeat
You can set a specific scene to be played repeatedly.
Title Shuffle
Plays titles in random order
1 During playback, select
in the Control Panel
Chapter Shuffle Plays chapters in random order
(
Shuffle Off
Clears Shuffle Play
want to start repeated playback.
The starting point (point A) is set.
2 Select N, and then press the
button.
2 Press the
playback.
button at the point you want to end repeated
The ending point (point B) is set, and repeated playback of the section
from A to B begins.
Using the playback modes
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing playback modes
Adjusting DVD player settings
Clears playback modes to allow normal playback.
1 Select
press the
button.
You can use the Control Panel to adjust DVD player settings, such as the
language for subtitles, audio language, and Parental Control level.
A message stating, "Play mode contents cleared", is displayed and the
console returns to normal playback.
Notes
• Some DVDs do not support all settings. The PlayStation®2 console plays disc
content as recorded in the DVD software. If the DVD does not support the features
listed, you will not be able to change the settings.
Note
If multiple playback modes have been set in a combination, all playback modes are
cleared.
• The following options are not available during playback or Resume Play
(
page 24). Clear Resume Play before changing these settings.
– "Menu", "Audio" and "Subtitles" in Language Setup
– "TV Type" and "Progressive" in Screen Setup
– "Parental Control" in Custom Setup
– "DTS" and "Audio Track Auto Select Mode" in Audio Setup
You can change DVD player settings using the following procedure:
1 Select
the
button.
The Setup icon bar is displayed.
2 Select the icon for the setting you want to change, and then
press the
button.
The current setting for each item is displayed.
3 Select the desired item, and then press the
button.
The menu option becomes active and can be selected.
Adjusting DVD player settings
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select the desired setting, and then press the
button.
Setting TV display options
The setting of the item is completed. For details, see the instructions
In the Screen Setup menu, you can set the screen size (aspect ratio) and
other options that affect picture quality.
Notes
TV Type
• The default setting for each menu item is underlined in the explanations below.
• To return to the Control Panel after making settings, press the SELECT button.
• Settings are saved when you do any of the following:
– Stop playback (including stopping Resume Play)
You can set the aspect ratio to match the screen of the connected TV.
16:9
Select this option when using a wide-screen TV or a standard
TV with special 16:9/wide-screen functionality.
– Open the disc cover
Setting language options
4:3 Letter Box
4:3 PAN SCAN
Select this option when using a standard TV. This setting
displays a wide picture with margins on the upper and lower
portions of the screen.
In "Language Setup" you can choose the language for the DVD's menu,
audio and subtitles. Note that if you select a language that is not recorded
on the DVD, one of the recorded languages is selected automatically.
Select this option when using a standard TV. This setting
displays a picture adjusted to the height of the screen, cutting
off portions at left and right that do not fit.
Menu
Selects the language for the DVD's menu
Selects the language for the DVD's audio track
Selects the language for the DVD's subtitles
Audio
Subtitles
Note
Note
When you set "Progressive" to "On", "TV Type" is automatically set to "16:9".
If you select "Audio Follow" for subtitles, the subtitle language will automatically be
set to match the language selected for the DVD's audio track.
Adjusting DVD player settings
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DNR (Digital Noise Reduction)
Progressive
You can use this setting to help reduce roughness in the on-screen image
and produce a cleaner picture.
You can display an image in which the picture updates all the lines in one
pass. In most cases, this results in a clearer, flicker-free image. This feature
is available only if your TV and AV Cable* support progressive scan
(480p).
Off
DNR is not used.
* The Component AV Cable (for PlayStation®2) (sold separately) is compatible
with progressive scan.
DNR1
DNR2
Increases picture quality
Increases picture quality (maximum)
On
Select this option when the console is connected to a TV that supports
progressive scan (480p).*
Notes
Off
Select this option when the console is connected to a standard TV.
• "DNR2" is more effective for reducing image roughness than "DNR1", but in some
cases an afterimage may appear. If this occurs, select "Off".
• The DNR function may produce limited results on some DVDs.
• When you set "Progressive" to "On", "DNR" is automatically turned off and cannot
be turned on.
* The DVD player's progressive scan mode is only available when playing a disc
recorded in NTSC format, and viewed on a TV that supports progressive scan
(480p).
Notes
Outline Sharpening
• If picture quality is reduced or no image is displayed, set "Progressive" to "Off"
when the console is connected to a TV without the necessary equipment. If you
accidentally set this option to "On" for such a TV, picture quality may be reduced
or the picture may not be displayed. To clear the setting, follow these steps:
You can sharpen or soften the outline of the on-screen image. The higher
the value, the sharper the outline. Normally, select "0".
• -2
• -1
• 0
• +1
• +2
Check that you have a DVD in the console.
1
2
Press the \/1 (on/standby)/RESET button on the console front.
Then press and hold down the START button of the Analog Controller
(DUALSHOCK®2) in controller port 1 until the DVD picture is displayed.
The "Progressive" setting is returned to "Off", allowing the DVD-Video to
be displayed as normal. You can also cancel this setting using the "Clear
Note
Depending on the DVD, Outline Sharpening may produce limited results.
Display
Progressive Setting" (
screen.
page 40) option in the Version Information
During playback, you can display playback status information in the top
right corner of the screen for a few seconds.
• DVDs can contain video-based and film-based material, which use different frame
rates. When playing video-based material using progressive scan, some images
may appear unnatural. If this occurs, set "Progressive" to "Off" and view in
standard interlace mode.
On
Playback status information is displayed for a few seconds.
Playback status information is not displayed.
Off
• When you set "Progressive" to "On", "TV Type" (
to "16:9".
page 29) is automatically set
Adjusting DVD player settings
30
Download from Www.Somanuals.com. All Manuals Search And Download.
• DVD-RW disc (VR mode) content can only be viewed in standard interlace format.
The "Progressive" option is not available when playing such content.
3 Select "Region", and then press the
button.
The list of region options is displayed.
4 Select the region to base the Parental Control level on, and
then press the button.
Setting viewer options
Pause mode
You can use this option to set the picture status when playback is paused.
5 Select "Level", and then press the
button.
The list of level options is displayed.
Auto
A picture with moving elements is displayed without jitter. Normally
select this position.
6 Select a restriction level, and then press the
button.
Frame
A picture without moving elements can be displayed at high resolution.
To clear Parental Control
set "Level" to "Off".
Parental Control
In some regions, the viewing of some DVD content may be restricted
based on viewer age or other factors. You can use the Parental Control
feature to restrict the level of content that may be viewed through your
console.
The lower the value, the stricter the restriction.
Setting Parental Control
1 Select "Parental Control", and then press the
button.
The screen for registering a password is displayed. If a password has
already been registered, the screen for confirming the password is
displayed.
2 Select a number, and then press the
button.
Repeat step 2 to enter a four-digit password. If you want to clear a
number, press the button. When registering a password, you are
required to enter it again for confirmation.
Adjusting DVD player settings
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Region code list
Changing your password
To enter a Parental Control region code, select "Other" in step 4 of "Setting
first letter, and then press the right directional button. Then select the next
following steps:
1 Using the directional buttons, select "Change Password" and
letter and press the
button.
then press the
button.
The screen for changing the password is displayed.
Region
Austria
Belgium
Canada
China
Code
AT
BE
CA
CN
DK
FI
Region
Code
MY
NL
NO
PH
Malaysia
Netherlands
Norway
2 Select a number, and then press the
button.
Repeat step 2 to enter a four-digit password. You are required to enter
it again for confirmation.
Philippines
Russia
Playing a disc restricted by Parental Control
Denmark
Finland
France
RU
SG
Singapore
Spain
You will be prompted to temporarily change the Parental Control level
to allow playback. This usually occurs immediately at disc start-up but
may also occur at different times depending on the DVD.
FR
DE
HK
ID
ES
Germany
Hong Kong
Indonesia
Italy
Sweden
SE
2 Using the directional buttons, select "Yes" and then press the
button.
Switzerland
Taiwan
CH
TW
TH
GB
The screen for entering the password is displayed.
IT
Thailand
United Kingdom
3 Select a number, and then press the
button.
Japan
JP
Repeat step 3 to enter the four-digit password. After entering the
password, playback will begin again. When DVD playback is stopped,
the Parental Control level returns to the original setting.
Korea
KR
Notes
• If you forget your password, see "Troubleshooting" (
• If you do not set a password, you cannot change the Parental Control settings.
• Some DVDs with the Parental Control feature do not allow use of playback modes
(
Adjusting DVD player settings
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Dolby Digital
Setting sound options
This option sets Dolby Digital as the output signal for the DIGITAL OUT
(OPTICAL) connector.
Audio Digital Out
On
Select this option when the console is connected to an audio device
with a built-in Dolby Digital decoder.
You can switch the method of outputting the audio signal when you
connect the following audio devices to the DIGITAL OUT (OPTICAL)
connector.
Off
Select this option when the console is connected to an audio device
without a built-in Dolby Digital decoder.
Caution
DTS
When the console is connected to an audio device without a Dolby Digital, DTS
or MPEG decoder, set "Dolby Digital", "DTS" and "MPEG" to "Off". If you set
these options to "On" without the necessary decoder, you may have no sound or
an extremely loud noise may be emitted.
This option sets DTS as the output signal for the DIGITAL OUT
(OPTICAL) connector.
On
Select this option when the console is connected to an audio device
with a built-in DTS decoder.
Digital Out (Optical)
This option sets the type of output for the DIGITAL OUT (OPTICAL)
connector.
Off
Select this option when the console is connected to an audio device
without a built-in DTS decoder.
On
Select this option when you want sound (audio signal) to be output
through the DIGITAL OUT (OPTICAL) connector.
MPEG
Settings for "Dolby Digital", "DTS" and "MPEG" are displayed.
This option sets MPEG AUDIO as the output signal for the DIGITAL
OUT (OPTICAL) connector.
Off
Select this option when you do not want sound to be output through the
DIGITAL OUT (OPTICAL) connector.
On
Select this option when the console is connected to an audio device
with a built-in MPEG decoder.
Settings for "Dolby Digital", "DTS" and "MPEG" are not displayed.
Off
Select this option when the console is connected to an audio device
without a built-in MPEG decoder.
Adjusting DVD player settings
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Track Auto Select Mode
This setting gives priority to the audio track that contains the highest
number of channels when you play a DVD on which multiple audio
formats (PCM, Dolby Digital, DTS or MPEG) are recorded. If PCM,
Dolby Digital, DTS and MPEG have the same number of channels, the
console selects PCM, Dolby Digital, DTS and MPEG audio tracks in that
order.
On
Priority given
Off
No priority given
Notes
• If you set "DTS" to "Off" in "Audio Digital Out" (
track is not played.
page 33), the DTS audio
• Depending on the DVD, the audio channel with priority may be predetermined. In
this case, the audio track will be selected based on the DVD's order of priority.
DVD Volume
You can set this option if the audio output level of the DVD is low. You
can set this only when "Digital Out (Optical)" is set to "Off" in "Audio
+2
+1
Turns up the volume (maximum)
Turns up the volume
Standard Normally select this option.
Caution
If you set this option to "+1" or "+2", the sound may become distorted. If this
happens, change the setting to "Standard". Also note that if you set the volume
too high, it may harm your hearing or damage the speakers.
Adjusting DVD player settings
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Main menu
Using the Browser screen
Displaying the main menu
You can do the following from the Browser screen:
• Copy or delete game data saved on a Memory Card
• Start a game
• Start playback of an audio CD
• Start playback of a DVD
From the main menu, you can access information and change various
settings. You can also move to the following screens from the main menu.
The main menu is displayed when you turn on the console without a disc
inserted.
2 Using the directional buttons, select "Browser" and then
press the
button.
The main menu is displayed. Note that it may take some time for the
main menu to be displayed.
The Browser screen is displayed.
3 Insert a disc or Memory Card.
the inserted item is displayed on the Browser screen.
\
Note
If you turn on the console with a disc inserted, the main menu will not be displayed.
To display the main menu, press the A (open) button on the console front and
remove the disc. Then press the =/1 (on/standby)/RESET button to reset the console.
Displaying the main menu
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select an icon, and then press the
button.
• When you select the Memory Card icon, icons for data saved on the
Memory Card are displayed. To copy or delete saved game data, see
Using the System Configuration
menu
• If you select the icon for a PlayStation®2 or PlayStation® format
software disc, the game will start.
• When you select the icon for an audio CD disc, the tracks contained
• If you select the icon for a DVD disc, playback of the DVD will
begin.
From the System Configuration menu, you can change settings for
numerous options including language or time display, and audio or video
output method.
Note
2 Using the directional buttons, select "System Configuration"
The message "There is no data" is displayed on the Browser screen when no Memory
Card or disc is inserted in the console.
and then press the
button.
The System Configuration menu is displayed.
3 Select an item, and then press the
button.
The menu option becomes active and can be selected.
4 Select the desired setting, and then press the
button.
38).
Using the System Configuration menu
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Screen Size
• The default setting for each menu item is underlined in the explanations below.
• Changes to each setting are saved and remain in effect even after you turn off or
reset the console.
You can set the display mode for the TV.
4:3
Select this option when using a standard TV with the
console.
Clock Adjustment
Full*
Select this option when using a standard TV with the
console. The black margins on the upper and lower
portions of the screen are cut off.
You can set the date and time. Use the directional buttons to set "Year",
"Month", "Day", "Hour", "Minute" and "Second". The setting goes into
effect when you press the
button.
16:9
Select this option when using a wide-screen TV or a
standard TV with special 16:9/wide-screen
functionality.
Optional settings
If you press the
button at the "Clock Adjustment" screen, you can set
* "Full" display mode is compatible with the System Configuration menu, Browser
screen and audio CD screen.
options such as "Date Format" or "Time Format". Use the directional
buttons and the
Time Format
button to make each setting.
Sets the system clock to either 12-hour or 24-hour
clock display
Digital Out (Optical)
You can set whether to output the signal through the DIGITAL OUT
(OPTICAL) connector.
Date Format
Time Zone
Sets the display order of year, month and day
Sets the time zone
On
Select this option when you want to output signal
through the DIGITAL OUT (OPTICAL) connector.
Daylight Savings Time
Sets Standard or Daylight Savings (Summer Time).
Normally select "Standard".
Off
Select this option when you do not want to output
signal through the DIGITAL OUT (OPTICAL)
connector.
Using the System Configuration menu
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Component Video Out
The following limitations apply when the DVD Remote Control is set to "Gameplay
Function On":
When using the Component AV Cable (for PlayStation®2) (sold
separately), you must set the mode to match the input jacks on your TV.
– Depending on the software, some remote control buttons may not work properly.
– The buttons of the DVD Remote Control will not work when two or more
buttons are pressed at the same time.
Y Cb/Pb Cr/Pr
RGB
Select this option when connecting the console to
component video input connectors (default setting for
SCPH-75002).
– Some software titles may stop operating properly when a controller is removed
from controller port 1. If this happens, set to "Gameplay Function Off".
Select this option when connecting the console to
RGB input connectors (default setting for
SCPH-75003).
Language
You can use this option to select the language displayed on the main menu,
Browser screen, System Configuration menu, and Version Information
screen.
Note
The "RGB" setting is only for PlayStation®2 and PlayStation® format software.
When you watch a DVD, the mode automatically switches to "Y Cb/Pb Cr/Pr".
English
French
Displays messages in English
Displays messages in French
Displays messages in Spanish
Displays messages in German
Displays messages in Italian
Displays messages in Dutch
Displays messages in Portuguese
Remote Control
Spanish
German
Italian
You can set this option when using the DVD Remote Control (for
PlayStation®2) (sold separately).
Gameplay Function On
Select this option when operating PlayStation®2 or
PlayStation® format software with the DVD Remote
Control.
Dutch
Portuguese
Gameplay Function Off
Select this option when not operating PlayStation®2
or PlayStation® format software with the DVD
Remote Control.
Using the System Configuration menu
38
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Select the desired setting, and then press the
button.
For details, see the instructions for each item (
Using the Version Information
screen
Note
The default setting for each menu item is underlined in the explanations below.
You can check version information for various console components by
selecting this option. You can also change optional settings for some items.
Console
button.
The PlayStation®2 console automatically adjusts its internal settings for
optimal playback. When "Diagnosis" is set to "On", the console makes
additional adjustments.
The Version Information screen is displayed.
Diagnosis
Off
On
Diagnosis is turned off.
Diagnosis is turned on.
Note
The "Diagnosis" setting will automatically return to the default setting in the
following cases:
Optional settings
– When playback of PlayStation®2 or PlayStation® format software or a DVD
begins
Optional settings are available for "Console", "PlayStation® Driver" and
"DVD Player". "DVD Player" can be set only if the DVD player's
"Progressive" option is set to "On".
– When the console is reset
– When the console is turned off
1 Using the directional buttons, select an item and then press
the
button.
The current setting for the item is displayed.
2 Select an item, and then press the
button.
The available options are displayed.
Using the Version Information screen
39
Download from Www.Somanuals.com. All Manuals Search And Download.
PlayStation® Driver
DVD Player
You can set the PlayStation® Driver programme to optimise performance
of PlayStation® format software.
If you set "Progressive" to "On" when the console is connected to a TV
without the necessary equipment, the picture quality may be reduced or the
picture may not be displayed. You can clear the "Progressive" setting by
following the procedure below.
Note
Remove the DVD before clearing the setting.
The settings will automatically return to the default settings in the following case:
– When the console is turned off
Clear Progressive Setting
Disc Speed
No
Leaves the "Progressive" setting on
Clears the "Progressive" setting
Standard Loads discs at normal speed
Yes
Fast
Loads discs at high speed
1 Display the Version Information screen.
Note
Set to "Standard" in the following cases:
2 Using the directional buttons, select "DVD Player" and then
– When fast loading does not produce improved results
– When using a software that is not compatible with fast loading
press the
button.
The "Clear Progressive Setting" option is displayed.
Texture Mapping
3 Press the
button.
Standard Displays as normal
4 Select "Yes", and then press the
button.
Smooth
Displays with reduced roughness in on-screen images
5 Press the
button twice.
The display returns to the main menu.
Note
Set to "Standard" in the following cases:
– When smooth texture mapping does not produce improved results
– If the picture does not display properly when set to "Smooth"
6 Press the A (open) button on the console front, and place a
DVD in the console.
Using the Version Information screen
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Networking
Connecting with a network cable
Connecting to a network
You can connect the console to a network using an Ethernet network cable
connected to the NETWORK connector on the console rear. You can
connect to a 100 Base-TX or 10 Base-T network. Refer to the instructions
supplied with the network device for details.
You can enjoy online games by connecting the PlayStation®2 console to a
broadband network. To play all online games, you will need the following:
• A Network Access Disc (supplied separately)
Basic network setup
• A Memory Card (8MB) (for PlayStation®2) (sold separately)
• A service contract with a Broadband Internet Service Provider (sold
separately)
Network line
Network equipment
This will vary depending on the
type of broadband service in your
home.
The type of equipment used will also
vary depending on the type of
service.
• An Ethernet Cable (sold separately)
• An External Network Device such as a Broadband enabled digital set-top
box, a cable modem, an ADSL modem or a router (sold separately)
Broadband modem, router etc.
Notes
• You cannot play online games with this console using a dial-up or ISDN
connection.
• USB connectivity from the External Network Device to the USB connector is not
supported.
Commercially
available network cable
• There are two types of network cables: straight-through cable and crossover cable.
Ensure that you use the correct type of cable when connecting your PlayStation®2
console to your Broadband Internet connection. Refer to the Instruction Manual
supplied with the network device, or your Broadband Internet Service Provider for
details.
PC
Note
When connecting the console and a PC to the network, a network device such as a
router or a hub may be required. Refer to the instructions supplied with the network
device for details.
Connecting to a network
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the console
Warning
Do not connect network cables or telephone cords of the following types to the
network connector; too much electrical current may pass through the connector,
causing a malfunction, excessive heat or fire in the connector:
- Standard residential telephone lines
Warning
Do not plug the AC power cord for the console into the electrical outlet until you
have made all other connections.
- Network cables not appropriate for use with a 10Base-T/100Base-TX network
- Any ISDN (digital) compatible phone or data line
- PBX phone lines
1 Connect the Ethernet network cable to the NETWORK
connector on the console rear.
- Other "unknown" types of telephone lines
Console rear
Commercially available network cable
2 Insert the connector on the network cable to the network
device.
The connection method will vary depending on the network device.
Refer to the instructions supplied with the network device for details.
Connecting to a network
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating network settings
After you have connected a network cable to the console, you will need to
create and save network settings. To do this you need a Network Access
Disc supplied by registering your PlayStation®2 console. You can register
your PlayStation®2 console by completing the Registration Card enclosed
Items you will need
To create a network setting, you will need the following items:
• A Memory Card (8MB) (for PlayStation®2) (sold separately)
• Login and network setup information provided by your Broadband
Internet Service Provider
Note
Depending on the type of Internet service used, you may need to provide your
Broadband Internet Service Provider with your MAC Address. You can find the
MAC Address for your console listed in the Version Information screen
(
Creating network settings
44
Download from Www.Somanuals.com. All Manuals Search And Download.
About DVD-Videos
Additional information
• The console can only play discs recorded for the PAL broadcast standard.
You cannot play discs recorded for other broadcast standards (such as
NTSC) on this console (unless the NTSC disc displays the "ALL" label
and an NTSC compatible TV is used).
Compatible software
• DVD-Videos are assigned a number (region code) for the geographic
region in which the disc can be played. This console can only play discs
marked with region code "4" (SCPH-75002 only), "2" (SCPH-75003
only) or "ALL".
You can play discs of the following types on the PlayStation®2 console:
Disc type
Disc logo
PlayStation®2 format DVD-ROM
[12 cm, Silver]
"
", PlayStation®2 logo and
ALL
ALL
designation
4
2
(SCPH-75002 only)
(SCPH-75003 only)
PlayStation®2 format CD-ROM
[12 cm, Blue]
"
", PlayStation®2 logo and
designation
About DVD-R, DVD-RW, DVD+R and DVD+RW discs
• Some discs may not be playable due to scratches, dust or problems
encountered during recording.
PlayStation® format CD-ROM
[12 cm, Black]
PlayStation® logo and
designation
Audio CD
• Only discs that have been "finalised" can be played.
[12 cm, 8 cm]
• Sections of video recorded on CPRM (Content Protection for Recordable
Media)-compatible DVD-RW discs or on CPRM-compatible DVD-R
discs using the "copy-once" capability cannot be played on this console.
DVD-Video*
[12 cm, 8 cm]
The "DVD VIDEO" logo is a
trademark.
Music discs encoded with copyright protection
technologies
DVD-RW (VR mode)
[12 cm, 8 cm]
The "DVD-RW" logo is a
trademark.
The audio CD playback feature of this product is designed to conform
to the Compact Disc (CD) standard. Recently, some record companies
have started marketing music discs encoded with copyright protection
technologies. Some of these music discs do not conform to the CD
standard and may not be playable on this product.
* Throughout this manual, the term "DVD-Video" is used to refer to DVD-R,
DVD-RW (Video mode), DVD+R and DVD+RW discs.
About PlayStation®2 format CD-ROM and DVD-ROM, and
PlayStation® format CD-ROM discs
The console can only play discs with the
Discs marked with
cannot be played.
designation.
,
or
Compatible software
45
Download from Www.Somanuals.com. All Manuals Search And Download.
About DualDiscs
A DualDisc is a two sided disc product which contains DVD recorded
material on one side and digital audio material on the other side. However,
since the audio material side does not conform to the Compact Disc (CD)
standard, playback on this product is not guaranteed.
Accessories
Optional accessories are available for this model of PlayStation®2 console.
When using optional accessories, be sure to purchase those that are
compatible with this model of PlayStation®2 console. Contact the
appropriate PlayStation® customer service helpline which can be found
within every PlayStation® and PlayStation®2 format software manual or
with this model.
Accessories not compatible with this model of
PlayStation®2 console
The following accessories are not compatible with this model of
PlayStation®2 console:
Model number
SCPH-10350 E
SCPH-1070 E
SCPH-10090 E
SCPH-10040 E
SCPH-10110 E
-
Product name
Network Adaptor (Ethernet) (for PlayStation®2)
Multitap
Multitap (for PlayStation®2)
Vertical Stand (for PlayStation®2)
Horizontal Stand (for PlayStation®2)
Product that use the S400 i.LINK connector
i.LINK and i.LINK logo " " are trademarks.
Accessories
46
Download from Www.Somanuals.com. All Manuals Search And Download.
About the DVD Remote Control (for
PlayStation®2)
GUARANTEE
• This model of the PlayStation®2 console features a built-in IR receiver.
When operating with a DVD Remote Control (for PlayStation®2) (sold
separately), do not insert an IR receiver (for PlayStation®2) into a
controller port of the console.
• When purchasing a DVD Remote Control for use with this console,
choose one that does not include a separate IR receiver Unit.
• You cannot open or close the disc cover using the DVD Remote Control.
GUARANTEE
Thank you for buying this Product. The term "Product" means the
PlayStation®2 computer entertainment system together with the
accessories and/or peripherals with which it is packaged. This Guarantee
does not cover any software whether or not packaged with the Product.
Sony Computer Entertainment Europe Ltd ("SCEE") guarantees that this
Product is free from defects in material and workmanship that result in
Product failure during normal usage in accordance with the terms set out
in below and will, for a period of 1 (one) year from the date of original
purchase, repair or (at SCEE's option) replace any component part of this
Product, free of charge, where it is faulty due to defective materials or
workmanship. Replacement will be with a new or refurbished component
or unit, at SCEE's option, which is guaranteed for the remainder of the
original Guarantee Period.
About Multitaps
Only the Multitap (for PlayStation®2) (SCPH-70120 E)* (sold separately)
can be used with this console. Do not connect Multitap products with other
model numbers to the console as this may result in damage to the console.
* You can use this product with both PlayStation®2 and PlayStation® format
software titles.
The benefits conferred by this Guarantee are in addition to the statutory
rights and remedies the consumer has in the UK and Eire in respect of this
Product and this Guarantee does not affect such rights and remedies in any
way. The benefits conferred by this Guarantee are also in addition to other
rights and remedies which the consumer has in law in Australia and New
Zealand in respect of this Product, including rights and remedies available
under the Trade Practices Act 1974 and State and Territory legislation in
Australia and the Fair Trading Act 1986 in New Zealand and this
Guarantee does not affect such rights and remedies in any way.
This Guarantee is given to you by Sony Computer Entertainment Europe
Ltd of 30 Golden Square, London, W1F 9LD, United Kingdom.
GUARANTEE
47
Download from Www.Somanuals.com. All Manuals Search And Download.
4. To the extent permitted by applicable law, this Guarantee will be your sole and
exclusive remedy in relation to defects in this Product and all other guarantees,
warranties, terms and conditions, express or implied by statute or otherwise, in
respect of this Product are excluded and neither SCEE nor any other Sony entity,
or their suppliers or authorised service facilities, will be liable for any special,
incidental, indirect or consequential loss or damage.
IMPORTANT
1. If you need to claim under this Guarantee, please call your local Customer Service
helpline (listed on the Customer Registration Card and PlayStation® and
PlayStation®2 format software manuals) for return instructions and other
guidance.
2. This Guarantee is only valid:
i. in the United Kingdom, Eire, Australia and New Zealand; and
If this Product needs any repair which is not covered by this Guarantee,
please call your local Customer Service helpline for advice. If your home
country is not one of those listed, please contact your retailer.
ii. when the original sales receipt or invoice or other proof of purchase
(indicating the date of purchase and retailer's name) is presented together with
the faulty Product (and has not been altered or defaced since the date of
original purchase); and
Please complete and return the enclosed (Freepost) Customer Registration
Card.
iii. when the Guarantee seal and the serial number on the Product have not been
damaged, altered or removed.
3. You may not claim under this Guarantee when the Product is damaged as a result
of:
i. commercial use, accident, fair wear and tear, negligence, abuse, or misuse
(including, without limitation, failure to use this Product for its normal
purpose and/or in accordance with instructions on proper use and
maintenance, or installation or use in a manner inconsistent with applicable
local technical or safety standards);
ii. use in conjunction with any unauthorised peripheral (including, without
limitation, game enhancement devices, adaptors and power supply devices);
iii. any adaptation or adjustment to, or alteration of, the Product carried out for
any reason, and whether properly carried out or not;
iv. maintenance or repairs carried out other than by a SCEE authorised service
facility; or
v. use in conjunction with unauthorised software, virus infection, or fire, flood
or other natural calamity.
GUARANTEE
48
Download from Www.Somanuals.com. All Manuals Search And Download.
AC adaptor
Specifications
Power requirements
100-240 V AC, 50/60 Hz
8.5 V, 5.65 A
Voltage/electrical current
output (approx.)
General
Adaptor dimensions (approx.)
Adaptor mass (approx.)
60 × 28 × 124 mm (w/h/d)
350 g
Power requirements
! DC IN 8.5V
Electrical current consumption 5.3 A
(approx.)
Supplied accessories
Console dimensions (approx.)
Console mass (approx.)
Signal format
230 × 28 × 152 mm (w/h/d)
900 g
Design and specifications are subject to change without notice.
PAL
Copyrights
Operating temperature
5 °C to 35° C
This product incorporates copyright protection technology that is protected
by method claims of certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Inputs/outputs on the console
front
Controller port (2)
MEMORY CARD slot (2)
USB connector (2)
Inputs/outputs on the console
rear
NETWORK connector
! DC IN 8.5V connector
AV MULTI OUT connector
DIGITAL OUT (OPTICAL) connector
This product is manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. ©1992-1997 Dolby Laboratories. All
rights reserved.
"DTS" and "DTS Digital Out" are trademarks of Digital Theater Systems,
Inc.
Specifications
49
Download from Www.Somanuals.com. All Manuals Search And Download.
About national export control
This product may fall within the scope of national export control
legislation. You must comply fully with the requirements of such
legislation and of all other applicable laws of any jurisdiction in relation to
this product.
Troubleshooting
Go through this section if you experience difficulty in operating the
PlayStation®2 console. Should any problem persist, call the PlayStation®
service line at the number listed on your guarantee card for assistance.
About copy protection
Attempted copying of DVD's played on this device, may be prevented or
restricted by copy protection technology contained on the DVD.
Attempted recording or copying of DVD's for private use by the removal
or circumvention of copy protection technology may be prohibited under
applicable law.
Check the following items first:
• The console is turned on.
• The AC power cord is connected properly to the electrical outlet.
• The cables are correctly and securely connected.
About access control
Check also for the TV or monitor and other connected devices.
This product incorporates access control technology. Use of software not
specifically designed for this product (excluding DVD-Videos and audio
CDs) and copies of software designed for this product are prevented by
access control. Unauthorised transfer, delivery, display, export, import, or
transmission of programs, devices, or the product modified with programs
or devices, to defeat the purpose of this access control feature is or may be
prohibited by law.
Picture
There is no picture on the TV screen.
, Check whether the =/1 (on/standby) indicator on the console front is lit up in red.
If it is red, press the =/1 (on/standby)/RESET button to turn on the console (the
=/1 indicator will turn green).
, Switch the input mode of the TV (or VCR) as appropriate for the connector in
use on the console.
, Try using another compatible AV Cable. There may be a problem with the AV
Cable in use.
, Set "Component Video Out" to "Y Cb/Pb Cr/Pr" in the System Configuration
menu (
page 38) when connecting the console to the component AV inputs on
a TV. Use the supplied AV Cable (integrated audio/video) to make the setting,
and then connect to the TV using the Component AV Cable (for PlayStation®2)
(sold separately).
, Check that the inserted disc can be played with the PlayStation®2 console
(
Troubleshooting
50
Download from Www.Somanuals.com. All Manuals Search And Download.
, See also "There is no picture on the TV screen" and "Picture noise
Picture noise appears on the TV screen.
, Check that the disc is clean and does not have any scratches. If the disc is dirty,
appears on the TV screen".
clean it (
page 6).
The aspect ratio does not change even when playing the DVD with the
aspect ratio setting adjusted and/or playing 16:9 pictures of a DVD.
, Depending on the DVD, the aspect ratio cannot be changed.
, Check that the console is connected to the TV directly. If there is a selector or
receiver (AV amplifier) connected between the console and TV, depending on
the type of device connected, the aspect ratio cannot be changed.
, If you move the console from a cold to a warm location, allow the console to
adjust to room temperature before use.
, If moisture condensation occurs, remove the disc and do not use the console for
several hours until the condensation evaporates (
, For some output connectors on a TV, the component video out setting needs to
page 6).
, Depending on the TV, the aspect ratio cannot be changed.
, Some PlayStation® format software titles may not perform properly on the
PlayStation®2 console. For more information, call the PlayStation® service line
at the number listed on your guarantee card for assistance.
The size of the video image and the TV screen do not match.
, Set the aspect ratio to match your TV screen (
page 37). If changing the
, Some TVs may experience a bouncing effect in their pictures when using the
PlayStation®2 console. If this happens, connect the console to another TV.
setting does not work, try adjusting the aspect ratio of your TV. Refer to the
instructions supplied with your TV for details.
"The disc could not be read" is displayed on the screen.
, Check that the disc is placed in the console with the label side facing up
Sound
(
, Check that the disc is clean and does not have any scratches. If the disc is dirty,
There is no sound.
, Switch the input mode of the TV (or VCR) as appropriate for the connector in
use on the console.
, Check that the TV volume is not set to "mute". Also check that the TV volume
level is set properly.
There is no picture or picture noise appears when playing a DVD.
, When playing a DVD, connect the console to the TV directly (
the video signal from the console is coming through a VCR to the TV, copy
protection on some DVDs may affect picture quality.
page 10). If
, If the console is connected to an audio device, check the settings on the
connected device. Refer to the instructions supplied with the device for details.
, Try using another compatible AV Cable (
page 9). There may be a problem
, If the console is connected to a TV or cable* that does not support progressive
scan (480p), no image will be displayed when you set "Progressive" to "On" in
with the AV Cable in use.
, Some PlayStation®2 format software titles do not support audio output from the
DIGITAL OUT (OPTICAL) connector. Connect the console to the audio device
using an analog AV Cable, such as the supplied AV Cable (integrated audio/
the Control Panel. Clear the "Progressive" setting (
noise appears when using a TV that supports progressive scan (480p), also clear
the "Progressive" setting.
video) (
page 9).
* The Component AV Cable (for PlayStation®2) (sold separately) is compatible
with progressive scan.
, A DVD-R or DVD-RW disc that is not finalised cannot be played on the
PlayStation®2 console.
, Content of a video recorded on CPRM-compatible DVD-R or CPRM-compatible
DVD-RW discs cannot be played on the PlayStation®2 console.
Troubleshooting
51
Download from Www.Somanuals.com. All Manuals Search And Download.
, For some DVDs with a Dolby Digital audio track, the output signal may not
Sound quality is poor.
, Check that the disc is clean and does not have any scratches. If the disc is dirty,
comprise the entire 5.1 channel range.
clean it (
page 6).
Operation
, If you move the console from a cold to a warm location, allow the console to
adjust to room temperature before use.
The controller does not function.
, If moisture condensation occurs, remove the disc and do not use the console for
, If the software title is compatible only with the Analog Controller
(DUALSHOCK®2), it will not work properly with the Analog Controller
(DUALSHOCK®). Use a controller that is appropriate for the software title.
Refer to the instructions supplied with the software for details.
, Check that the controller is set to the appropriate mode for the software. Refer to
the instructions supplied with the software for details.
several hours until the condensation evaporates (
page 6).
, Some PlayStation® format software titles may not perform properly on the
PlayStation®2 console. For more information, contact the appropriate
PlayStation® customer service helpline which can be found within every
PlayStation® and PlayStation®2 format software manual.
, Try using another controller that is compatible with the PlayStation®2 console.
There may be a problem with the controller in use.
There is no sound or the sound quality from the digital audio equipment
is poor.
, Check that the disc is clean and does not have any scratches. If the disc is dirty,
The console does not recognise the Memory Card. Data cannot be
saved or copied to the Memory Card.
, Check that the Memory Card is compatible with the software in use
clean it (
, Set "Digital Out (Optical)" to "On" in the System Configuration menu
, If playing a DTS audio track using an audio device with a built-in DTS decoder,
page 6).
(
(
, Check that the Memory Card is inserted securely (
, Check that you are saving the data correctly. Refer to the instructions supplied
with the software for details.
to an audio device without a built-in DTS decoder, select tracks other than DTS
audio tracks to play.
, Data cannot be saved if there is not enough free space on the Memory Card.
, Try using another Memory Card. There may be a problem with the Memory Card
in use.
, Some PlayStation®2 format software titles do not support audio output from the
DIGITAL OUT (OPTICAL) connector. Connect the console to the audio device
using an analog AV Cable, such as the supplied AV Cable (integrated audio/
video) (
page 9).
Data saved on a Memory Card is corrupted.
, While saving, loading, copying or deleting data, do not attempt any of the
following. Doing so may damage the data.
• Do not remove the Memory Card or the controller.
• Do not open the disc cover.
, See also "There is no sound" and "Sound quality is poor".
Surround effect is not present when playing a DVD with a Dolby Digital
audio track.
, Check that the console is connected to an audio device with a built-in Dolby
Digital decoder using an optical digital cable.
• Do not reset the console.
• Do not turn off the console.
, Check that the settings of the audio device are correct. Refer to the instructions
supplied with the device for details.
, Corrupted data can be deleted in the Browser menu (
, Set "Dolby Digital" to "On" in "Audio Digital Out" (
page 33).
Troubleshooting
52
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Enter the number "7444".
The registered password is cleared, and the screen for registering a password
is displayed. Enter a new password (
The console does not function properly.
, Static electricity and other similar occurrences may affect the console's
operation. Turn off the console and unplug it from the electrical outlet. Then,
replug and turn on the console by pressing the @/1/RESET button.
Some functions are not available.
, Depending on the DVD, some functions may not be available:
• Stop, Search, Slow, Program Play, Shuffle Play or Repeat Play may be
prohibited.
The @/1 indicator flashes in red and the console does not work.
, Do not use the console until the flashing stops. Placing the console in an
extremely hot location or blocking the console's vents raises the internal
temperature of the console, thereby preventing proper operation.
• The audio language cannot be changed on discs that do not have multiple audio
tracks. Also, some DVDs do not allow the audio language to be changed.
• If multilingual subtitles are not recorded on the DVD, you cannot change the
language for the subtitles. It may not be possible to change the subtitle
language or turn the subtitles off.
The console makes noise or shakes.
, Because PlayStation®2 format software titles load at a higher speed than
PlayStation® format software titles, the noise or vibration may be greater.
• If multiple angles are not recorded on the DVD, you cannot change the viewing
angles. Changing the viewing angles may be prohibited.
The DVD does not play.
• You can only select
Check whether a DVD-RW disc (VR mode) is inserted in the console.
when playing a DVD-RW disc (VR mode).
, Check that the DVD has the correct region code. Also check that the broadcast
signal of the disc is compatible with the console (
page 45).
, The Parental Control feature may be set on the disc. Follow the on-screen
Some DVD settings cannot be changed.
instructions and temporarily raise the level of Parental Control (
, Some settings cannot be changed during playback or Resume Play (
Stop playback completely or clear Resume Play (
page 24) before attempting
You forget your password.
to adjust the settings.
, You can clear the password using the following procedure:
1 Start a DVD, and then stop playback.
Clear Resume Play (
page 24). Use a DVD without the Parental Control
feature.
2 At the Control Panel, select
and then press the
button
(
3 Select "Parental Control", and then press the
button.
The screen to enter a password is displayed. If the screen to register a
password is displayed, no password had been registered before. In this case,
register a new password.
4 Press the SELECT button.
The screen to clear the password is displayed.
Troubleshooting
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Network
Connection to the network cannot be established.
, Check that the network settings are correct. Refer to the instructions supplied
with the software or the information from your Internet service provider and
adjust the settings accordingly.
, The network is busy. Wait a few minutes, and then try to access the network
again.
, Check that the network cable is properly connected (
, Check that you are using the correct type of network cable.
, Check that the network settings or connections of the network device are correct.
Refer to the instructions supplied with the network device for details.
Troubleshooting
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
"
", "PlayStation", "
", "DUALSHOCK" and "
" are registered trademarks of Sony Computer Entertainment Inc.
is a trademark of Sony Corporation.
"SONY" and " " are registered trademarks and
© 2005 Sony Computer Entertainment Inc. All rights reserved.
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|