n N
2
Network Media Receiver
Notice
Trademarks and copyrights
Sony, VAIO, the VAIO logo, SonicStage, PictureGear Studio, Remote Commander, VAIO Media, VAIO Media Integrated Server, VAIO Zone and VAIO Media Console
are trademarks or registered trademarks of Sony.
Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation.
Java is a trademark or registered trademark of Sun Microsystems, Inc.
Intent is a trademark of Tao Group Limited, which may be registered in some jurisdictions.
All other trademarks are trademarks or registered trademarks of their respective owners.
In the manual, the ™ and ® signs are not specified.
Television programmes, films, videotapes, CDs and other materials may be copyrighted. Such materials recorded with this device are for your personal use only.
Unauthorised recording of such material may be contrary to the provisions of the copyright laws. The law prohibits adding any modification to the recorded materials
including but not limited to motion pictures, images and audio, without authorisation from the copyright holder.
Some of these materials may be duplication-protected to disable unlawful recording.
Owner's record
The model number and serial number are located on the bottom of your Network Media Receiver.
Print out his page, record the model and serial number in the space provided below, and keep in a secure location. Refer to the
model and serial numbers when you call the VAIO-Link Sony Service Centre.
Model Number:
Serial Number:
Regulatory information
Sony hereby declares that this product is in compliance with the essential requirements and other relevant provisions of European
Directive 1999/5/EC. To obtain a copy of the declaration of conformity (DoC) with the R&TTE Directive, please access the following
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
3
Network Media Receiver
Notice
Safety information
This Sony product is designed and tested to comply with the safety regulations. Use of this equipment in a manner not approved in
this manual may be hazardous. Read the safety and caution information before operating the Network Media Receiver, complying
with all safety precautions and warnings.
❑
❑
❑
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
The power socket outlet you are using must be installed near the equipment and must be easily accessible.
Audio and picture distortion may occur if this equipment is positioned in close proximity to any equipment emitting
electromagnetic radiation.
Stop operating the unit immediately, under these circumstances:
❑
❑
❑
❑
The unit emits smoke or fumes.
The unit makes loud or unusual noise.
Water or any foreign object has fallen into the unit.
The unit has been dropped or otherwise damaged.
To reduce any potential hazard, proceed as follows:
❑
❑
❑
Unplug the AC adapter from the AC wall outlet or power supply strip.
Unplug the AC adapter and cables from the unit.
Contact the VAIO-Link Customer Service Centre for repair information.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
4
Network Media Receiver
Notice
Precautions
About the Network Media Receiver
❑
❑
❑
This equipment is for use only in the country of purchase. Using this equipment under a different voltage may cause fire or electric
shock. Use of this equipment in other countries may be prohibited by local laws.
Do not expose this equipment to grease, smoke, moisture, or dust. Such exposure may cause fire or electric shock. Use under
conditions other than those suggested in this manual may cause fire or electric shock.
Do not allow water or any foreign objects to enter the unit. This may cause fire or electric shock. In the event that water or other
foreign objects enter the unit, immediately unplug the AC adapter from the electrical outlet and contact VAIO-Link for inspection
and/or repair.
❑
❑
Do not disassemble the equipment. This may cause fire, electric shock, or injury. Contact VAIO-Link for inspection and/or repair.
Do not connect inappropriate network or phone lines to the Ethernet port. Connect only 100BASE-TX/ 10BASE-T cables to the
Ethernet port. Connecting inappropriate network or phone lines to the Ethernet port may result in an electric current overload
that can result in malfunction, excessive heat, or fire in the port. For help on connecting to a network, see your network
administrator.
❑
Set up the Network Media Receiver and connection cables in a protected location out of the reach of children, to avoid personal
injury or damage to the equipment.
❑
❑
❑
Install the Network Media Receiver so that you can easily reach the power outlet in the event of an emergency.
Do not drop the Network Media Receiver. A sharp impact can damage the unit.
Do not place the Network Media Receiver in the following locations:
❑
❑
❑
❑
In direct sunlight or near heat sources. Operate this equipment at temperatures between 0°C and 40 °C.
On or near equipment that generate electromagnetic fields, such as speakers or televisions.
On or near a microwave oven.
In a dusty or dirty location.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
5
Network Media Receiver
Notice
❑
❑
❑
❑
❑
❑
On an insecure or uneven surface.
In a location that is subject to vibration.
In a location that is subject to moisture or rapid temperature change.
Near obstacles that shield or block electrical signals, such as metal or concrete walls.
In a location with poor ventilation.
If there is a rapid change in temperature, condensation (water droplets) may form in the Network Media Receiver, causing it
to malfunction.
If this occurs, disconnect the equipment from the VAIO computer and TV for two to three hours. The unit should resume
normal operation.
❑
To clean the Network Media Receiver, wipe it with a soft, dry cloth.
If the unit requires more cleaning, use a soft cloth that is slightly moistened with a mild detergent solution. Avoid getting the
terminals wet.
❑
❑
Do not use cleaners that contain thinner, benzene, or alcohol, as these compounds may damage the surface of the equipment.
Avoid connecting these phone lines to the Network connector on the unit:
❑
❑
❑
Private Branch Exchange (PBX) lines;
Network cables that do not meet the 100BASE-TX and 10BASE-T standards;
Home or business phone lines.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
6
Network Media Receiver
Notice
About the AC adapter
❑
Use the AC adapter that is supplied with the Network Media Receiver. Using a different AC adapter may cause damage to the
Network Media Receiver.
❑
❑
Unplug the AC adapter from the AC wall outlet if the equipment is not being used for extended periods of time.
Unplug the AC adapter from the electrical outlet during a lightning storm. Lightning may cause electric shock or damage to the
equipment. When severe lightning is expected, unplug the AC adapter from the electrical outlet to avoid fire, electric shock, or
damage to the equipment. Do not touch the equipment during a lightning storm.
About the remote control
❑
Use only AA-size alkaline batteries in the remote control.
❑
Remove the batteries from the remote control when it is not in use for extended periods of time.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
7
Network Media Receiver
Welcome
Welcome
Congratulations on your latest Sony purchase! Your new Network Media Receiver is a superb blend of high technology and easy-
to-use functionality. The information provided in this user guide is designed to help you become familiar with the Network Media
Receiver and its features.
Please make sure you have read the printed Getting Started booklet before using your Network Media Receiver equipment.
What is the Network Media Receiver?
The Network Media Receiver enables you to display still images, play videos or music files on your TV screen, when the Network
Media Receiver is connected to a VAIO computer that contains your video and audio content.
✍ The Network Media Receiver can accommodate multiple VAIO computer connections by using a router with a built-in or standard network switch, or a network switch device.
This enables you to switch between computers to locate your favourite audio or video files.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
8
Network Media Receiver
Welcome
Video
Play previously recorded programmes stored on your VAIO computer.
★ Use the film roll feature to search for a specific place in your recorded programme.
✍ The TV function is not supported, and will not be supported in the future.
Music
❑
Play music files stored on your VAIO computer.
❑
Play a music track continuously (loop feature).
Photos / still images
❑
❑
❑
View the photo collections stored on your VAIO computer, in slideshow format.
View your photos as thumbnails in Index view.
Select your favourite photo for viewing.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
9
Network Media Receiver
Welcome
Locating controls and connectors
This section describes the controls, jacks, and ports available on the Network Media Receiver and the remote control.
Front panel
1
2
3
POWER/REC indicator
The indicator is white while the power is on. The indicator is red during TV recording. The indicator blinks
red during firmware updates.
Infrared receiver
Enables communication between the Network Media Receiver and the remote control. Do not block the
area in front of the infrared receiver.
Power button/Standby indicator
Turns the Network Media Receiver on and off. The indicator is dimmed (red) when the unit is in Standby
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
10
Network Media Receiver
Welcome
Back panel
The back panel contains ports and jacks for supplied and optional cables.
1
2
3
4
5
6
Optical OUT port
Supports the digital optical input of an audio device.
S-video jack
Connection for an S-video cable.
Video jack
Connection for a video cable.
Audio L jack
Connection for an audio cable (left).
Audio R jack
Connection for an audio cable (right).
Ethernet port
Connection for a 100BASE-TX/10BASE-T Ethernet cable (RJ-45).
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
11
Network Media Receiver
Welcome
Remote control
The Network Media Receiver is controlled using the remote control. The remote control can start and stop video recording/playback,
and set viewing preferences.
TV
CHANNELPOWERPOWER
MUTE
+
TV/VIDEO
-
DISPLAY
1
4
2
5
8
0
3
6
AUDIO
7
CLEAR
9
ENTER
REC
REC STOP
REW
FWD PREV NEXT
STOP
PLAY
PAUSE
OPTIONS
MAIN MENU
SELECT
FUNCTION
RETURN
TV VOLUME CHANNEL
PAGE
UP
PAGE
DOWN
NETWORK
MEDIA RECEIVER
PM-NM10E
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
12
Network Media Receiver
Welcome
!
BECAUSE THE TV FUNCTION IS UNAVAILABLE, NOT ALL BUTTONS ON THE REMOTE CONTROL WORK.
Button
Function
1
2
3
4
5
6
TV channel buttons *
MUTE button
Press + or - to change TV channels.
Press to turn off the sound. Press again to restore the sound.
Press to select specific channels.
Press to delete the channel numbers selected.
Press to begin recording.
Channel number buttons
CLEAR button *
REC button *
*
REW button
FWD button
Press to rewind during video or music playback.
Press to fast-forward during video or music playback.
7
8
9
STOP button
Press to stop video or music playback.
OPTIONS button
Press to display the available options for video, music or photo servers.
Direction arrow buttons
SELECT button
Press a direction arrow button to navigate within the video, music, or photo servers.
Press to select operations, settings, features, or other choices, while using the video, music or photo servers.
10 FUNCTION button
11 TV VOLUME switch (+/-) *
12 POWER button
Press to toggle between the Network Media Receiver features, such as video, music or photo.
Use this switch to increase (+) or decrease (-) the TV’s volume.
Press to turn your TV on or off.
13 POWER button
Press to turn the Network Media Receiver on or off.
Press to select TV or Video mode.
14 TV/VIDEO button *
15 DISPLAY button
16 AUDIO button
Press to display setting information for video, music, and photos.
Press to select audio mode.
17 ENTER button *
18 REC STOP button *
Press to activate channel selections made using the channel number buttons.
Press to stop video recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
13
Network Media Receiver
Welcome
Button
Function
19 PREV button
Press to return to a previous music track.
Press to advance to the next music track.
NEXT button
20 PAUSE button
21 PLAY button
Press to pause video, music or slideshow playback.
Press to begin playback of videos, music, or slideshows.
Press to return to the main selection screen.
22 MAIN MENU button
23 RETURN button
Press to return to the previous screen, feature or mode.
24 CHANNEL switch
*
Use this switch to change TV channels. The Page Up/Page Down feature enables you to scroll within folders
containing playlists or video recordings.
✍ These buttons do not function because they are linked to the TV function. This is not a malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
14
Network Media Receiver
Welcome
Documentation delivered with the Network Media Receiver
❑
❑
❑
Network Media Receiver User Guide (this guide) — Contains information about setting up and using the Network Media
Receiver. The user guide also provides resources for technical support, safety guidelines, and supporting software.
Getting Started (printed) — This quick reference provides quick and easy instructions to set up the Network Media Receiver
and your VAIO computer.
Setup poster (printed) — A visual quick reference sheet showing the configuration of the Network Media Receiver equipment,
as well as the important specifications of the unit.
❑
❑
Sony guarantee leaflet (printed).
Safety and Regulations guide (printed).
VAIO computer compatibility
The Network Media Receiver supports certain Sony VAIO computers. Check that your VAIO computer is compatible with the
Network Media Receiver, before you begin hardware setup or configuration.
✍ For current updates on VAIO computer compatibility with the Network Media Receiver, see the VAIO-Link website: http://www.vaio-link.com.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
15
Network Media Receiver
Welcome
PC system requirements
Your compatible VAIO computer(s) must:
❑
❑
❑
Have the Microsoft Windows XP Home Edition or Professional operating system installed;
Have the VAIO Media software (platform and servers) preinstalled;
Be equipped with VAIO Zone software.
Wireless LAN requirements
To use Wireless LAN functions with the Network Media Receiver, we recommend the following:
❑
❑
PCWA-DE30
PCWA-A320
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
16
Network Media Receiver
Welcome
Multimedia compatibility
Video and movie file compatibility
Only video recordings recorded on a VAIO computer with VAIO Zone can be viewed using the Network Media Receiver. Other video
file formats may not be compatible with the Network Media Receiver. For details on how to use VAIO Zone, see the VAIO Zone
guide provided on disc with your VAIO computer, and the VAIO Zone Help files, which are within the software itself.
Music file compatibility
Only playlists that are managed by the SonicStage software are supported by the Network Media Receiver. Other music files or
songs purchased from an Internet Electronic Music Distribution (EMD) service are not compatible for playback using the Network
Media Receiver. For details on how to use SonicStage, go to the SonicStage Help files, which are within the software itself.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
17
Network Media Receiver
Setting up the hardware
Setting up the hardware
This section contains information about setting up your Network Media Receiver connections. It is designed to complement the
printed Network Media Receiver Getting Started guide.
Setting up the remote control
To set up the remote control, proceed as follows:
1
2
Open the battery cover on the back of the remote control.
Insert two AA batteries (supplied) by matching the + and - on the batteries, with the diagramme inside the battery compartment.
✍ Under normal use, the AA batteries may last up to six months. If your remote control does not operate properly, the batteries may need replacing. If your remote control is
not being used for long periods of time, remove the batteries to avoid possible damage from leaking batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
18
Network Media Receiver
Setting up the hardware
Programming the remote control
Your remote control is preprogrammed to control certain TVs. Refer to your TV manufacturer’s code table for more information. The
remote control may not be compatible at all with some TV models, even when the appropriate TV manufacturer code is entered.
If you are using a Sony TV set, you do not need to program the remote control, as it is set by default.
To program the remote control, proceed as follows:
1
2
3
Press and hold the SELECT button.
Enter your TV code number, using the channel number buttons.
Release the SELECT button after you have entered the TV code number.
✍ After replacing the batteries in your remote control, the TV manufacturer’s code may require resetting. Reset the code each time you replace the batteries.
TV Manufacturer
Akai
Code Number
02, 04
25
TV Manufacturer
Mivar
Code Number
15
Beko
NEC
16
Daewoo
Finlux
04, 05, 06
26
Panasonic
Philips
17
04
Goldstar/LG
Grundig
Hitachi
04, 07
07
Pioneer
19
Samsung
Sanyo
04, 07
02
04, 27, 28
02, 11
04, 07
04
JVC
Schneider
Sharp
02, 03, 04
21
Loewe
Medion
Mitsubishi
Thomson
Toshiba
22
13, 14
03, 24
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
19
Network Media Receiver
Setting up the hardware
Connection possibilities
Connecting the Network Media Receiver to a TV
Use the supplied audio/video connection cable to connect the Network Media Receiver and your TV. Connect the cable by matching
the connector colours to the jack colours on the TV’s audio/video jacks.
Optional equipment and cables may be required to connect the Network Media Receiver, TV, VCR and VAIO computer, depending
on your connection environment.
Video Input
1
S-video
Video
L
Audio
R
1
2
S-video cable (sold separately)
Audio/video connection cable (supplied)
✍ The arrows indicate the signal direction.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
20
Network Media Receiver
Setting up the hardware
Connecting the Network Media Receiver and your TV through a video recorder
Use the supplied audio/video connection cable to connect the Network Media Receiver and your video recorder. Connect the cable
by matching the connector colours to the jack colours on the VCR’s audio/video jacks.
Optional equipment and cables may be required to connect the Network Media Receiver, TV, VCR and VAIO computer, depending
on your connection environment.
✍ The arrows indicate the signal direction.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
21
Network Media Receiver
Setting up the hardware
Connecting the Network Media Receiver to digital sound system equipment
You can connect to a digital sound system as long as it has an optical-in port.
Use an optical digital connection cable (sold separately) to connect the Network Media Receiver and your digital sound system
equipment.
To connect the equipment, proceed as follows:
1
2
Insert one end of an optical digital cable (sold separately) into the optical OUT port on the Network Media Receiver.
Insert the other end of the optical digital cable into the optical IN port on the sound system equipment.
✍ Optional equipment and cables may be required to connect the Network Media Receiver and your VAIO computer, depending on your connection environment.
The arrows indicate the signal direction.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
22
Network Media Receiver
Setting up the hardware
Finding the most suitable working environment
You can connect the Network Media Receiver to your VAIO computer(s) using the Ethernet port on your VAIO computer(s), a router
with a built-in network switch, or a network switch device. These home network environment scenarios can help determine the best
❑
❑
❑
❑
❑
❑
❑
Environment 2: DSL/cable modem with built-in router, without network switch ports (page 24)
Environment 3: DSL/cable modem without a built-in router (page 25)
Environment 4: Network cable is connected to a LAN, shared in a residential complex (page 26)
Environment 5: VAIO computer is connected to the Internet using the built-in modem (page 27)
Environment 6: VAIO computer is not connected to the Internet (page 28)
Environment 7: Connecting multiple VAIO computers (page 29)
Please take the following notes into account:
❑
❑
❑
Optional equipment and cables may be required to connect your Network Media Receiver and VAIO computer(s).
All equipment and cables must be compatible with 100BASE-TX/10BASE-T standard.
If applicable, see the manual supplied with your DSL or cable modem to verify that it is equipped with a built-in router and
network switch ports.
❑
❑
❑
If using a multiple port network switch device (sold separately) or if using environment 5 or 6, the VAIO computer requires a fixed
IP address for the LAN connection (see Assigning a fixed IP address (page 30)).
Connections may vary depending on your network environment. Contact your Internet Service Provider for connection
information.
The pictures are for illustration purposes only. PC configuration may vary.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
23
Network Media Receiver
Setting up the hardware
Environment 1: DSL/cable modem equipped with a built-in router and network switch ports
Read the notes on page 22, then proceed as follows:
1
2
Connect the Network Media Receiver to your DSL/cable modem* (1), using the network cable (2).
Connect the Ethernet jack on each VAIO computer to the jack(s) on the DSL/modem, using additional network cables* (3).
* Sold separately.
Internet
LAN
LINE
MONITOR
USB
MIC HEADPHONES LINE IN
MONITOR
AUDIO
–
S
VIDEO/VIDEO
–
AUDIO
S
VIDEO/VIDEO
VHF/UHF
VIDEO OUTPUT
VIDEO1 INPUT
PHONE
LINE
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
24
Network Media Receiver
Setting up the hardware
Environment 2: DSL/cable modem with built-in router, without network switch ports
Read the notes on page 22, then proceed as follows:
1
2
3
Connect the Network Media Receiver to a network switch device (1), using the network cable (2).
Connect the Ethernet jack on each VAIO computer to the jack(s) on the network switch, using additional network cables* (3).
Connect the network switch device to the DSL or cable modem, using a network cable* (4).
* Sold separately.
Internet
LAN
LINE
MONITOR
USB
MIC HEADPHONES LINE IN
MONITOR
AUDIO
–
S
VIDEO/VIDEO
–
AUDIO
S
VIDEO/VIDEO
VHF/UHF
VIDEO OUTPUT
VIDEO1 INPUT
PHONE
LINE
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
25
Network Media Receiver
Setting up the hardware
Environment 3: DSL/cable modem without a built-in router
Read the notes on page 22, then proceed as follows:
1
2
3
Connect the Network Media Receiver to a router device with a network switch* (1), using the network cable (2).
Connect the Ethernet jack on each VAIO computer to the jack(s) on the router device, using additional network cables* (3).
Connect the WAN jack on the router device, to the LAN jack on the DSL or cable modem, using a network cable* (4).
* Sold separately.
Internet
LAN
LINE
WAN
LAN
MONITOR
USB
M
I
C
H
E
A
D
P
H
O
N
E
S
L
I
N
E
I
N
MONITOR
A
UDIO
S
VIDEO/VIDEO
–
AUDIO
S
VIDEO/VIDEO
VHF/UHF
–
VIDEO OUTPUT
VIDEO1 INPUT
PHONE
LINE
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
26
Network Media Receiver
Setting up the hardware
Environment 4: Network cable is connected to a LAN, shared in a residential complex
Read the notes on page 22, then proceed as follows:
1
2
3
Connect the Network Media Receiver to a router device with a built-in network switch* (1), using the network cable (2).
Connect the Ethernet jack on each VAIO computer to the jack(s) on the router device, using additional network cables* (3).
Connect the WAN jack on the router device to the LAN jack (residential complex) (4).
* Sold separately.
LAN
WAN
LAN
MONITOR
USB
M
I
C
H
E
A
D
P
H
O
N
E
S
L
I
N
E
I
N
MONITOR
AUDIO
–
S
VIDEO/VIDEO
–
AUDIO
S
VIDEO/VIDEO
VHF/UHF
VIDEO OUTPUT
VIDEO1 INPUT
PHONE
LINE
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
27
Network Media Receiver
Setting up the hardware
Environment 5: VAIO computer is connected to the Internet using the built-in modem
Read the notes on page 22, then proceed as follows:
1
2
3
4
Insert one end of the crossover cable (1) into the Ethernet jack on your VAIO computer.
Insert the other end of this crossover cable into the connection adapter (2).
Insert one end of the network cable (3), into the connection adapter.
Insert the other end of this network cable into the Ethernet jack on the Network Media Receiver (4).
MONITOR
USB
MIC HEADPHONES LINE IN
MONITOR
AUDIO
–
S
VIDEO/VIDEO
–
AUDIO
S
VIDEO/VIDEO
VHF/UHF
VIDOUTPUT
VIDEO1 INPUT
O
LINE
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
28
Network Media Receiver
Setting up the hardware
Environment 6: VAIO computer is not connected to the Internet
Read the notes on page 22, then proceed as follows:
1
2
3
4
Insert one end of the crossover cable (1) into the Ethernet jack on your VAIO computer.
Insert the other end of this crossover cable into the connection adapter (2).
Insert one end of the network cable (3), into the connection adapter.
Insert the other end of this network cable into the Ethernet jack on the Network Media Receiver (4).
MONITOR
USB
MIC HEADPHONES LINE IN
MONITOR
AUDIO
–
S
VIDEO/VIDEO
–
AUDIO
S
VIDEO/VIDEO
VHF/UHF
VIDEO OUTPUT
VIDEO1 INPUT
PHONE
LINE
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
29
Network Media Receiver
Setting up the hardware
Environment 7: Connecting multiple VAIO computers
This method is related under certain conditions similar to environments 5 and 6.
Read the notes on page 22, then proceed as follows:
1
Connect the Network Media Receiver to a router device with a built-in network switch, or a multiple port network switch
device (1), using the network cable (2).
2
Connect the Ethernet jack on each VAIO computer to the jack(s) on the router device, using additional network cables* (3).
When using a router device with a built-in network switch, a WAN connection is not necessary.
* Sold separately.
WAN
LAN
MONITOR
USB
MIC HEADPHONES LINE IN
MONITOR
AUDIO
–
S
VIDEO/VIDEO
–
AUDIO
S
VIDEO/VIDEO
VHF/UHF
VIDEO OUTPUT
VIDEO1 INPUT
PHONE
LINE
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
30
Network Media Receiver
Setting up the hardware
Assigning a fixed IP address
In some environments, each VAIO computer in your network requires a fixed IP (Internet Protocol) address:
❑
❑
❑
If your VAIO computer is connected to the Internet using the installed modem, as in environment 5.
If your VAIO computer is not connected to the Internet, as in environment 6.
If you are connecting more than one VAIO computer using a network switch device, as in environment 7, or the network switch
device is not connected to a router device.
A fixed IP address is not required when your VAIO computer(s) is networked through a router with a built-in or standard network
switch.
To assign a fixed IP address, proceed as follows:
1
2
3
4
5
6
Click Start on the Windows taskbar and select My Computer.
The My Computer window appears.
In the Other Places section, click My Network Places.
The My Network Places window appears.
Click View Network Connection.
The View Network Connection window appears.
Right-click Local Area Connection and select Properties from the shortcut menu.
The Local Area Connection Properties dialog box appears.
From the General tab, select Internet Protocol (TCP/IP) and click Properties.
The Internet Protocol (TCP/IP) Properties dialog box appears.
Select Use the following IP address and specify an IP address and subnet mask, using the following format:
IP address: 169.254.XXX.XXX (replace XXX with a numeric value between 001 and 254 — as an example: 169.254.222.222)
Subnet mask: 255.255.0.0 (use this number for the subnet mask).
7
Click OK.
The IP address is fixed, as specified.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
31
Network Media Receiver
Setting up the hardware
8
Close the Local Area Connection Properties and the Internet Protocol (TCP/IP) Properties dialog boxes.
✍ When you set up the Network Media Receiver, the IP address must be specified. See Specifying an IP address (page 40).
When specifying the IP address for the Network Media Receiver, use different numbers where the IP address numbers are represented as “XXX.XXX.”
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
32
Network Media Receiver
Setting up the software
Setting up the software
This section provides information on configuring the media server, video, music and photo / still image software on your VAIO
computer.
Configuring VAIO Media
VAIO Media software manages the interaction between the Network Media Receiver and your VAIO computer(s), by enabling the
computer(s) to act as a music, photo, and video servers.
A VAIO computer that comes with VAIO Media software preinstalled can be used as a VAIO Media server in a network environment.
Preparing your multimedia content
❑
Music files: Use SonicStage ver. 2.1 to create play lists of music tracks on your VAIO Media server computer. Use MP3 files
stored in the shared folder that you can configure in VAIO Media Console.
❑
❑
Still image files: Use images files stored in the shared folder that you can configure in VAIO Media.
Video recordings: Use VAIO Zone to create video recordings on your VAIO Media Integrated server computer.
The VAIO Media Integrated Server software automatically makes these recordings available to VAIO Media users on your
network.
Setting up a VAIO Media server computer
Use the preinstalled VAIO Media Console software on your VAIO computer to start the VAIO Media Integrated Server.
To set up a computer as a VAIO Media server, proceed as follows:
1
2
Click Start on the Windows taskbar, select All Programs.
Point to VAIO Media, then to Server Administration, and click Console.
The VAIO Media Console dialog box appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
33
Network Media Receiver
Setting up the software
3
In the section Access Control Settings, select the option Access this computer from other computers on the network.
A warning message appears.
4
5
6
7
8
Read the message and click OK.
Select the option No device registration needed in a secure network environment.
In the section Start and Stop Servers verify that all available servers are shown as Started.
If the servers are shown as Stopped, click Start.
Click Close in the VAIO Media Console window.
✍ The music play lists, video cabinets and photo collections are available for network sharing only when the VAIO Media server software is started.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
34
Network Media Receiver
Using the Network Media Receiver - general settings
Using the Network Media Receiver - general settings
Once you have made your hardware connections and set up the other software applications, you can start using the Network Media
Receiver.
❑
❑
❑
❑
❑
❑
Starting and stopping the Network Media Receiver (page 35)
Specifying an IP address (page 40)
Making your own settings (page 42)
Restoring the original factory settings (page 46)
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
35
Network Media Receiver
Using the Network Media Receiver - general settings
Starting and stopping the Network Media Receiver
To start using the Network Media Receiver, proceed as follows:
1
2
3
If applicable, turn on the router using the power button or switch.
Turn on your VAIO computer.
Turn on your TV by pressing the TV POWER button on the remote control (see Remote control (page 11) for details on button
functions).
4
5
Switch the input connection to the Network Media Receiver by pressing the TV/VIDEO button on the remote control.
Turn on the Network Media Receiver by pressing the POWER button on the remote control.
The POWER/REC indicator lights up and the Main Menu screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
36
Network Media Receiver
Using the Network Media Receiver - general settings
6
To highlight an option, use the direction arrow buttons on the remote control, then press the SELECT button to confirm your
choice.
✍ When the Standby indicator light is red (dimmed), the Network Media Receiver is ready to be turned on. The Standby indicator takes approximately 20 seconds to light
after the AC adapter is plugged into a wall outlet.
!
The TV - Watch and record TV programs is not available.
To stop using the Network Media Receiver, proceed as follows:
1
Turn off the Network Media Receiver by pressing the POWER button on the remote control.
The POWER/REC indicator turns off and the Main Menu screen no longer appears on your TV screen.
2
3
Turn off your TV by pressing the TV POWER button on the remote control.
Turn off your VAIO computer using the recommended steps in the Hardware Guide of your VAIO.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
37
Network Media Receiver
Using the Network Media Receiver - general settings
Registering the Network Media Receiver and your VAIO computer
The Network Media Receiver enables you to restrict access to your VAIO computer, accepting access from the Network Media
Receiver only.
To register the Network Media Receiver, proceed as follows:
1
2
3
On the remote control, press the MAIN MENU button.
The Main Menu appears.
Highlight Settings, then press the SELECT button.
The Settings screen appears.
Highlight System Settings, then press the SELECT button.
The System Settings screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
38
Network Media Receiver
Using the Network Media Receiver - general settings
4
Highlight Device Registration, then press the SELECT button.
The Registration screen appears.
5
Highlight OK, then press the SELECT button.
The Registration screen appears.
✍ If the registration of the Network Media Receiver and the VAIO computer are cancelled, you need to begin the registration again.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
39
Network Media Receiver
Using the Network Media Receiver - general settings
To register the Network Media Receiver to your VAIO computer, proceed as follows:
1
2
Click Start on the Windows taskbar, select All Programs.
Point to VAIO Media, point to Server Administration, and click Console.
The VAIO Media Console dialog box appears.
3
In the Access Control Settings section, select the option Access this computer from other computers on the network.
A warning message appears.
4
5
6
Read the message and click OK.
From the VAIO Media Console, select the option Register the devices accessing this computer (recommended).
Click Registered Devices.
The Registered Devices dialog box appears.
7
Click Register.
The Device Registration dialog box appears.
8
9
Clear the check box Use the confirmation number to register your device.
Click Start Registration.
The Receiving Registration Request dialog box appears, showing the registration progress.
10 When the Registration Confirmation message box appears, respond to the prompt Do you want to add the device Sony
Network Media Receiver? by clicking Yes.
The Sony Network Media Receiver is added to the List of Registered Devices.
11 Close all open windows.
To complete the registration, proceed as follows:
1
2
When Registration Completed is displayed on the TV screen, highlight Close.
Press the SELECT button.
The Network Media Receiver is registered to your VAIO computer.
The TV screen displays the System Settings screen again.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
40
Network Media Receiver
Using the Network Media Receiver - general settings
Specifying an IP address
To specify an IP address through the Network Media Receiver, proceed as follows:
1
2
Make sure you are connected to the Internet.
On the remote control, press the MAIN MENU button.
The Main Menu screen appears.
3
4
Highlight Settings, then press the SELECT button.
The Settings screen appears.
Highlight System Settings, then press the SELECT button.
The System Settings screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
41
Network Media Receiver
Using the Network Media Receiver - general settings
5
Highlight IP Address, then press the SELECT button.
The IP Address screen appears.
6
7
8
Highlight Specify IP Address, then press the SELECT button.
Highlight the IP Address numbers, then press the SELECT button.
Use the channel number buttons or the up/down arrow buttons to enter numbers for the IP address and the subnet mask, then
press the SELECT button.
9
Highlight OK, then press the SELECT button.
10 Turn the Network Media Receiver off, then restart it, to enable the changes to take effect.
✍ If you are not using a router device, select Obtain the IP address automatically (not using router). An IP address and subnet mask are generated automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
42
Network Media Receiver
Using the Network Media Receiver - general settings
Making your own settings
You can conveniently access certain the Network Media Receiver features and functions by customising the default settings for your
Network Media Receiver and VAIO computer.
Connecting to a server automatically
You can set the Network Media Receiver to automatically connect to a VAIO computer (server), when accessing Video, Music, or
Photo content. These steps establish a specific VAIO computer as the default server for the Video, Music, and Photo features
available through the Network Media Receiver. Repeat these steps for each feature.
To select a server, proceed as follows:
1
2
3
Start up the Network Media Receiver as described in Starting and stopping the Network Media Receiver (page 35).
Select a feature, such as Video - Watch video clips.
Press SELECT.
The Select a server screen appears, listing the names of the available servers.
4
5
Highlight a server and press SELECT.
Highlight Connect and press SELECT to connect to the required server.
✍ If the status of a server is shown as
, try selecting Connect from the submenu, the press the SELECT button on the remote control.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
43
Network Media Receiver
Using the Network Media Receiver - general settings
Cancelling the default server settings
To cancel the default server settings, proceed as follows:
1
2
3
4
From the Select a server screen, press SELECT.
Choose Delete from list and press SELECT again.
Press the OPTIONS button on the remote control.
Select Refresh and then OK.
✍ Your default server settings are deleted if the AC power is interrupted or if the Network Media Receiver software is updated.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
44
Network Media Receiver
Using the Network Media Receiver - general settings
Configuring a default startup screen
To configure a default startup screen, proceed as follows:
1
2
Start up the Network Media Receiver as described in Starting and stopping the Network Media Receiver (page 35).
From the Main Menu, highlight Settings and press SELECT.
The Settings screen appears.
3
4
Highlight System Settings and press SELECT.
The System Settings screen appears.
Highlight Startup Menu and press SELECT.
The Startup Menu screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
45
Network Media Receiver
Using the Network Media Receiver - general settings
5
6
Highlight a screen you want as the startup screen, and press SELECT.
Select OK, then press the SELECT button.
✍ The startup screen which you set as default is deleted if the AC power is interrupted.
Configuring your VAIO computer to start automatically
You can set your VAIO computer to start automatically when the Network Media Receiver attempts to connect. This is a convenient
feature to use when the computer is in a different physical location from the Network Media Receiver. This setting requires your
computer to be in Standby or Hibernate mode.
To have your computer start automatically when the Network Media Receiver connects, proceed as follows:
1
2
Click Start on the Windows taskbar and select Control Panel.
Click Performance and Maintenance, then click System.
The System Properties dialog box appears.
3
4
5
6
Click the Hardware tab, then click Device Manager.
The Device Manager window appears.
Click + next to Network Adapter.
The drop-down tree displays all available network adapters.
Double-click the network adapter that connects the computer to the Network Media Receiver.
The network adapter’s Properties dialog box appears.
From the Power Management tab, select the options Allow this device to bring the computer out of standby and Only allow
management stations to bring the computer out of standby.
7
8
Click OK.
Close the Device Manager window, then click OK to close the System Properties dialog box.
✍ A Power Management tab should be available for the selected network adapter. If more than one network adapter is listed, select the device that has the Power
Management tab available in the Properties dialog box.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
46
Network Media Receiver
Using the Network Media Receiver - general settings
Restoring the original factory settings
You can reset these features to the original factory default settings:
❑
❑
❑
❑
❑
❑
❑
Startup menu
IP address
Recording mode
Live mode (not available)
Default server (VAIO computer)
Slideshow intervals
Slideshow repeat (looping)
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
47
Network Media Receiver
Using the Network Media Receiver - general settings
To reset the original factory settings, proceed as follows:
1
2
3
4
On the remote control, press the MAIN MENU button.
The Main Menu appears.
Highlight Settings, then press the SELECT button.
The Settings screen appears.
Highlight System Settings, then press the SELECT button.
The System Settings screen appears.
Highlight Factory Default, then press the SELECT button.
The Default settings screen appears.
5
Highlight OK, then press the SELECT button.
All settings are reset to the originaDlofwancltooardyfrosmetWtinwgw.sS.omanuals.com. All Manuals Search And Download.
n N
48
Network Media Receiver
Using the Network Media Receiver - general settings
Updating the Network Media Receiver firmware
The Network Media Receiver enables you to use your VAIO computer to update the Network Media Receiver firmware.
To update firmware, proceed as follows:
1
2
3
4
On the remote control, press the MAIN MENU button.
The Main Menu appears.
Highlight Settings, then press the SELECT button.
The Settings screen appears.
Highlight System Settings, then press the SELECT button.
The System Settings screen appears.
Highlight Firmware update, then press the SELECT button.
The Firmware Update screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
49
Network Media Receiver
Using the Network Media Receiver - general settings
5
Highlight OK, then press the SELECT button.
The Network Media Receiver prepares to download the firmware update.
The POWER/REC indicator starts blinking (red) slowly.
6
On your VAIO computer, start the update tool and begin updating the system software of the Network Media Receiver.
During the download, the POWER/REC indicator starts blinking rapidly.
Do not unplug the AC power cord or the network cable during the download.
When the update is completed, the Network Media Receiver goes into Standby mode.
!
Once you have started the firmware update process, do not attempt to stop or cancel it. All buttons on the remote control are disabled during the update.
✍ All settings except for the IP address are reset to the default settings, once the update is completed. The firmware update takes approximately three minutes to complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
50
Network Media Receiver
Watching videos
Watching videos
This section provides information on using the Network Media Receiver to watch video recordings with your VAIO computer and TV.
Playing videos
The Network Media Receiver enables you to view video recordings, recorded with VAIO Zone, on your TV screen. You can also use
the Network Media Receiver to watch compatible video files.
The Network Media Receiver displays the video recording names as identified in VAIO Zone software. For details on how to use
VAIO Zone features, refer to the VAIO Zone guide delivered on disc with your VAIO computer, and the VAIO Zone Help files within
the software itself.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
51
Network Media Receiver
Watching videos
To watch video content, proceed as follows:
1
On the remote control, press the MAIN MENU button.
The Main Menu appears.
2
Highlight VIDEO - Watch video clips, then press the SELECT button.
The Select a Video Server screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
52
Network Media Receiver
Watching videos
3
4
Highlight a server that contains the required video recordings, and press the SELECT button.
Highlight Connect and press the SELECT button.
The Video - All Libraries screen appears.
5
Highlight the video cabinet that contains the required video recording, then press the SELECT button.
The video cabinet opens and a list of available video recordings is displayed.
6
7
Highlight a video recording to play, then press the SELECT button.
Highlight PLAY, then press SELECT.
The Network Media Receiver starts playing the selected video recording.
8
Use the STOP, PLAY and PAUSE buttons on the remote (just like on your VCR) to control the video playback.
Viewing while rewinding or fast-forwarding
To view the video recording while rewinding or fast-forwarding, proceed as follows:
1
Using the remote control, press the REW or the FWD button.
Press the FWD / REW button once to fast-forward / rewind the video.
Press the FWD / REW button twice to control the video in 30-second increments.
2
Press the PLAY button to resume normal video playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
53
Network Media Receiver
Watching videos
Sorting videos
The Video - All Libraries screen enables you to sort video recordings by name or by recorded date/time, in ascending or descending
order.
To sort video recordings, proceed as follows:
1
2
3
Press the OPTIONS button while the Video - All Libraries screen is displayed.
The OPTIONS menu appears.
Press the arrow buttons to highlight Sort, then press the SELECT button.
A submenu appears.
Press the up or down arrow buttons to specify the sort order, then press the SELECT button.
The video recordings are sorted as specified.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
54
Network Media Receiver
Watching videos
Changing the video settings
When you use different servers as the default for the Video and TV features, all recorded TV programmes are stored on the computer
being used as the default TV server.
To change the video settings, proceed as follows:
1
Press the OPTIONS button while the Video - All Libraries screen is displayed.
The OPTIONS menu appears.
2
Highlight Video Settings, then press the SELECT button.
The Video Settings screen appears.
3
4
Highlight the Yes or No option, then press the SELECT button.
Highlight OK, then press the SELECT button.
The display returns to the Video - All Libraries screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
55
Network Media Receiver
Watching videos
Using the film roll feature
The Network Media Receiver has a thumbnail view (film roll) feature that enables you to select the frame to start playback.
To select the film roll feature, proceed as follows:
1
2
3
Press the up arrow button during video playback or pause.
A film roll appears on your TV screen.
Press the right or left arrow button to move the cursor to a specific frame, then press the SELECT button.
Playback starts from the specified frame.
To hide the film roll, press the up or down arrow button.
Using the time search feature
The time search feature enables you to find a specific frame to start playback by specifying a playback time.
To select the time search feature, proceed as follows:
1
2
3
Press the OPTIONS button during playback or pause.
A submenu appears.
Highlight Time search and press SELECT.
The Time Search screen appears.
Use the number buttons to enter a specific time and press SELECT.
Playback starts at the specified playback time.
✍ If you entered a wrong number, press the CLEAR button to erase the entry.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
56
Network Media Receiver
Watching videos
Resuming video playback from the original frame
You can return to the frame where playback was previously stopped and resume playing back the video recording.
To do this, proceed as follows:
1
2
From the Video - All Libraries screen, highlight the video recording to play, then press the SELECT button.
A submenu appears.
Highlight Resume, then press the SELECT button.
The media player starts playing the video recording from the frame where playback was previously stopped.
✍ The Resume function maintains a history of the last 5 playback actions, along with frame where each playback was stopped. When you play more than 5 video recordings,
the information on the oldest playback is erased from this history.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
57
Network Media Receiver
Listening to music
Listening to music
This section provides information on using the Network Media Receiver to listen to music with your VAIO computer and TV.
Playing music
The Network Media Receiver enables you to play music files stored on your VAIO computer with SonicStage software, using your
TV’s sound system or a digital sound system connected to your TV.
The playlists managed by the SonicStage software are supported by the Network Media Receiver. Other music files may not be
compatible with the Network Media Receiver.
The Network Media Receiver displays the playlist names and playlist folder names as identified in SonicStage software. For details
on how to use SonicStage software, see the Help files within the software itself.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
58
Network Media Receiver
Listening to music
To listen to music, proceed as follows:
1
On the remote control, press the MAIN MENU button.
The Main Menu appears.
2
3
Highlight MUSIC - Listen to music, then press the SELECT button.
Highlight a server that contains the required playlists or music tracks and press the SELECT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
59
Network Media Receiver
Listening to music
4
Highlight Connect and press the SELECT button.
The Music - All Libraries screen appears, displaying both folders and playlists.
5
6
Highlight the folder that contains the required playlist, then press the SELECT button.
Highlight the required playlist, then press the PLAY button.
The playlist opens and the Network Media Receiver starts playing from the first track in the playlist.
✍ If the playlist cover art is available on the SonicStage software, it is displayed on your TV screen. Otherwise, the default playlist cover art is displayed on your TV screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
60
Network Media Receiver
Listening to music
Navigating within a playlist during playback
To navigate within a playlist, proceed as follows:
1
2
3
On the remote control, press the PREV button once.
The current music track plays from the beginning.
Press the PREV button twice.
The previous music track begins to play.
Press the NEXT button once.
The next track begins to play.
To rewind or fast-forward the music track, proceed as follows:
1
2
Using the remote control, press the REW or the FWD button.
Press the PLAY or PAUSE button to resume playback of the music track.
To pause playback, proceed as follows:
1
2
Press the PAUSE button on the remote control.
Press the PLAY button to resume playback of the music track.
To stop playback, press the STOP button on the remote.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
61
Network Media Receiver
Listening to music
Looping a music track
The Repeat function enables you to repeat the playback of a single music track or an entire playlist.
To loop a music track, proceed as follows:
1
Press the OPTIONS button during the playback of the music track or playlist.
The OPTIONS menu appears.
2
3
Highlight Repeat, then press the SELECT button.
A submenu appears.
Highlight ON, then press the SELECT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
62
Network Media Receiver
Listening to music
Choosing a play mode
Play Mode enables you to play all tracks in a playlist (normal playback), play a specific musictrack, or play musictracks in the playlist
randomly (shuffle).
To choose a play mode, proceed as follows:
1
2
3
Press the OPTIONS button during the playback of the playlist.
The OPTIONS menu appears.
Highlight Play mode, then press the SELECT button.
A submenu appears.
Highlight a play mode, then press the SELECT button.
✍ In shuffle mode, only the song that is being played has the title displayed, all the other songs have only their number but no title displayed.
The playback mode Track plays the current music track only.
Sorting folders or playlists
The Music - All Libraries screen enables you to sort folders or playlists by name, in ascending or descending order.
To sort folders or playlists, proceed as follows:
1
2
3
Press the OPTIONS button while the Music - All Libraries screen is displayed.
The OPTIONS menu appears.
Press the up or down arrows to highlight Sort, then press the SELECT button.
A submenu appears.
Press the up or down arrows to specify the sort order, then press the SELECT button.
The folders and playlists are sorted as specified.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
63
Network Media Receiver
Viewing photos
Viewing photos
This section provides information on using the Network Media Receiver to view photos in slideshow format or as individual still
images, using your VAIO computer and TV. Please note that due to lower resolutions and refresh rates used on most TVs, the picture
quality on your TV set might be lower than that of a computer display.
Only the photos managed with PictureGear Studio software, or the photo files stored in a designated folder are supported by the
Network Media Receiver. The pictures stored in the Contents folder can also be shared and viewed by the Network Media Receiver.
To start viewing your photos, proceed as follows:
1
Press the MAIN MENU button on the remote control.
The Main Menu appears.
2
3
Highlight PHOTO - View photos, then press the SELECT button.
Highlight a server that contains thDeorwenqlouaidrefrdompWhowtwo.Scomolalneucatliso.cnosm.aAnlldMsantiulal lismSaeagrechs,AandnDdopwnrelosasd.the SELECT button.
n N
64
Network Media Receiver
Viewing photos
4
Highlight Connect and press the SELECT button.
The Photo - All Libraries screen appears, displaying available folders and photo collections.
5
6
Highlight the folder that contains the required photo collection or photos, then press the SELECT button.
The folder opens and a list of available still images is displayed.
Highlight the collection or still image to view, then press the PLAY button.
The Network Media Receiver starts playing the selected collection or photos as a slideshow on your TV.
✍ Only still image files are compatible for viewing with the Network Media Receiver.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
65
Network Media Receiver
Viewing photos
Using index view (thumbnails)
Index View enables you to view still image files (photos), stored on your photo server, in thumbnail view.
To use the index view, proceed as follows:
1
From the Photo - All Libraries screen, highlight the collection or still image to view and press the OPTIONS button.
A submenu appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
67
Network Media Receiver
Viewing photos
Changing the slideshow settings
You can set the time interval between the photos in a slideshow or set the photos to display in a loop (repeat).
To change the slideshow settings, proceed as follows:
1
2
Press the OPTIONS button while the Photo - All Libraries screen is displayed.
The OPTIONS menu appears.
Highlight Photo settings, then press the SELECT button.
The Photo Settings screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
68
Network Media Receiver
Viewing photos
3
4
5
In the Slide Show Interval section, use the right or left arrow buttons to highlight a time value, then press the SELECT button.
In the Slide Show Repeat section, use the right or left arrow buttons to highlight ON or OFF, then press the SELECT button.
Highlight OK, then press the SELECT button.
The Photos - All Libraries screen is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
69
Network Media Receiver
Viewing photos
Adding background music to a slideshow
To add background music to a slideshow, proceed as follows:
1
Press OPTIONS while a slideshow is playing.
A submenu appears.
2
3
4
Highlight Background music on..., then press SELECT.
Highlight a server that contains the required background music playlist and press the SELECT button.
Highlight Connect and press the SELECT button.
The Background Music - All Libraries screen appears.
5
Select a playlist for the background music, then press SELECT.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
70
Network Media Receiver
Viewing photos
Additional information
❑
❑
❑
❑
❑
❑
❑
To hide the on-screen information (text), press the DISPLAY button on the remote control.
To view the previous picture, press the PREV button once.
To view the next picture, press the NEXT button.
To stop a slideshow, press the STOP button.
To pause the slideshow, press the PAUSE button.
To resume the slideshow, press the PLAY button.
To display the previous screen or menu, press the BACK button.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
71
Network Media Receiver
Troubleshooting
Troubleshooting
This section describes how to troubleshoot common problems.
❑
❑
❑
❑
About power connections (page 72)
About the remote control (page 75)
About visual and audio reception (page 75)
About connecting to a server (page 77)
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
72
Network Media Receiver
Troubleshooting
About power connections
The Network Media Receiver does not start or operate
❑
Connect the AC adapter securely.
The Standby indicator light is red (dimmed) once the AC power cord is connected between the Network Media Receiver unit
and the wall power outlet.
❑
Make sure all cables are connected securely.
If you are using a power cord extension, power strip, or surge suppressor, make sure that it is turned on and securely connected
to the wall power outlet.
❑
❑
Make sure fresh batteries are properly installed in the remote control.
Unplug the AC adapter from the power outlet and plug it in again. Doing so resets the Network Media Receiver to the original
factory default settings.
❑
The Network Media Receiver takes approximately 20 seconds to start, after connecting to AC power. If the unit’s Standby
indicator does not light within 20 seconds, the Network Media Receiver may be damaged.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
73
Network Media Receiver
Troubleshooting
The Network Media Receiver does not turn off
If the displayed screen is frozen or unresponsive, or you cannot turn the Network Media Receiver off, the unit may have become
unstable.
To reset the unit, proceed as follows:
1
Press the power button on the Network Media Receiver for more than five seconds or disconnect the AC adapter from the
Network Media Receiver.
2
Wait 20 seconds for the Standby indicator to light in red, then turn the Network Media Receiver unit on.
Resetting the Network Media Receiver or reconnecting the AC adapter resets the unit’s settings to the original factory default
settings.
3
To completely disconnect power to the Network Media Receiver, unplug the AC adapter.
The Network Media Receiver goes into Standby mode and the Standby indicator light is red (dimmed).
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
74
Network Media Receiver
Troubleshooting
The VAIO computer does not resume from Standby or Hibernate mode
❑
Make sure the computer, server and network settings are configured correctly.
❑
Check the following, if applicable to your connection environment:
❑
❑
A crossover cable is securely connected between the Network Media Receiver and a single VAIO computer.
The network switch or the router device is turned on (see the information supplied with your network switch or router device
for details).
❑
❑
❑
The router device is turned on before turning on the Network Media Receiver.
The Network Media Receiver, network switch, or router device are properly connected using the appropriate network cables*.
If using a router device, the Network Media Receiver and the VAIO computer have been configured to obtain the IP address
automatically.
❑
Verify that the correct server name appears in the Select a server screen (the Select a server screen lists all current and
previous servers connected to the Network Media Receiver).
❑
❑
When connecting to the Network Media Receiver for the first time, the Network Media Receiver does not automatically bring a
VAIO computer out of Standby mode. Subsequent connections bring your VAIO computer out of Standby mode.
The Network Media Receiver cannot automatically resume the functions of certain VAIO computers due to computer settings or
the network environment. The automatic resume feature is not available for VAIO notebook computer models or for VAIO
computers that use a wireless LAN connection. This Resume feature is available for wired networks only.
* Use network cables that support 100BASE-TX/10BASE-T.
✍ The connected server history is lost when the AC power cable is disconnected. All settings except for the IP address are lost.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
75
Network Media Receiver
Troubleshooting
About the remote control
The remote control does not control TV functions
❑
Make sure your TV is compatible.
The remote control does not work with all TV models.
❑
❑
❑
Make sure the fresh batteries are properly installed in the remote control.
Make sure the correct TV manufacturer code is set for the remote control.
When you replace the batteries in the remote control, reset the TV manufacturer code again.
About visual and audio reception
There is nothing displayed on the TV screen
If your VAIO computer has become unstable and stops responding, turn it off and restart the computer.
Check the following:
❑
❑
❑
❑
❑
❑
The TV set is turned on and the power indicator light is on.
The Network Media Receiver is turned on and the power indicator light is on.
The Network Media Receiver and the TV are connected properly.
The TV is connected to the Network Media Receiver, using the video/S-video-in jack.
The TV is set to the correct channel and that the correct port has been selected on your TV.
VAIO Media Integrated Server is running.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
76
Network Media Receiver
Troubleshooting
Visual and audio reception is interrupted or distorted
❑
The network may not have enough bandwidth.
❑
Check the following, if applicable to your network environment:
❑
❑
The network cables support 100BASE-TX/10BASE-T.
The network switch or the router device supports 100BASE-TX/10BASE-T.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
77
Network Media Receiver
Troubleshooting
About connecting to a server
Cannot connect to a server
❑
❑
❑
Make sure the VAIO computer(s) are turned on.
Make sure the network settings are configured correctly.
Confirm the following, if applicable to your network environment:
❑
❑
A crossover cable is used for a direct connection between the Network Media Receiver and a single VAIO computer.
The network switch or the router device is turned on (see the information supplied with your network switch or router device
for details).
❑
❑
❑
The router device is turned on before turning on the Network Media Receiver.
The Network Media Receiver, network switch, or router device are properly connected using the appropriate network cables*.
If using a router device, the Network Media Receiver and the VAIO computer have been configured to obtain the IP address
automatically.
❑
The correct server name appears in the Select a server screen (the Select a server screen lists all current and previous
servers connected to the Network Media Receiver). If the server still does not appear in the Select a server screen, turn off
the Network Media Receiver and disconnect then reconnect the AC adapter. Turn on the Network Media Receiver again and
check that the server appears in the Select a server screen.
❑
❑
To use the automatic resume feature**, the VAIO computer must be in Standby or Hibernate mode.
Verify that the IP address of the Network Media Receiver is obtained properly. If using a router device, the Network Media
Receiver and the VAIO computer must be configured to obtain the IP address automatically. If Obtain the IP address
automatically is specified in the IP Address screen, an IP address is shown in the IP Address screen.
❑
VAIO Media Integrated Server is running.
❑
The VAIO computer may have become unstable. Turn off and restart the VAIO computer.
* Use network cables that support 100BASE-TX or 10BASE-T.
** The Network Media Receiver automatically brings the VAIO computer out of Standby or Hibernate mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
78
Network Media Receiver
Troubleshooting
The required server is not displayed in the Select a server screen
To refresh the Select a server list, proceed as follows:
1
2
Press the OPTIONS button on the remote control, then select Refresh.
Press the SELECT button.
Refreshing the list may take longer than a few moments.
❑
❑
❑
Verify that the VAIO Media Integrated Server is running on the VAIO computer and that the status is shown as Started.
To use the Video feature, the VAIO computer must be running and have a user logged on.
If the server still does not appear in the Select a server screen, turn off the Network Media Receiver and disconnect then
reconnect the AC adapter. Turn on the Network Media Receiver again and check that the server appears in the Select a server
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
79
Network Media Receiver
Troubleshooting
The server is listed as Unknown
When this is shown for a server, the Network Media Receiver does not recognise the computer’s availability and fails to connect.
In this case, proceed as follows:
1
2
Using the remote control, select Connect from the on-screen submenu.
Press OK.
If these steps do not connect the server, try the following:
❑
If necessary, bring the computer out of Standby or Hibernate mode.
You can configure your computer to enable the Network Media Receiver to automatically resume from Standby or Hibernate
modes.
❑
❑
❑
❑
Make sure the computer is turned on.
Make sure the network cable connections are secure.
If using a network switch device or a router device with a built-in network switch, make sure the equipment is turned on.
Make sure the network status is up.
The Select a server screen always appears
You can set the Network Media Receiver to stop displaying the Select a server screen every time you access a feature, such as
Video, Music or Photo. Preset a default server for each feature. See Connecting to a server automatically (page 42), for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
n N
80
Network Media Receiver
Troubleshooting
Specifications
Model
PCNA-MR10A
Hardware MPEG2 decoder
MPEG2 (max. 8 Mbps, 720 x 576 pixels, 25 fps)
MPEG1 (max. 1.41 Mbps, 352 x 288 pixels, 25 fps)
Compatible file formats*
Video**
Music
Photo
MPEG2, MPEG1
ATRAC3, ATRAC3plus, WAVE, MP3
BMP, TIF, GIF, JPEG, PNG
Connectors
video output
audio output
S-video, composite video out
Audio left, audio right, optical digital audio out
Ethernet network
100BASE-TX/10BASE-T*** x 1 (RJ-45)
AC 100V-240V ~ 50Hz-60Hz
0°C to 40°C
Power requirements
Operating temperature
Power use
during operation
during standby
6.5 W
2 W
Dimensions of unit (width x height x depth) 29 mm x 141 mm x 155 mm
Weight of unit
Approx. 600 g
Supplied accessories
Unit stand, remote control, AA batteries (2), audio/video cable, AC adapter, power cable,
network cable, crossover cable, connection adapter, spacers, documentation with CD-ROM
Specifications are subject to change without notice.
* May vary depending upon the VAIO server software specification.
** Video compatibility may vary depending on the VAIO server equipped with VAIO Zone.
*** Video function is not guaranteed when using 10BASE-T.
For more information, please refer to the VAIO Zone manual and the VAIO Media online help files.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Snapper Snow Blower SS5220E User Manual
Sony Computer Drive CRX160E User Manual
Sony Network Card MSAC FD1B User Manual
Sony Projector VPL CS4 User Manual
Southbend Hot Beverage Maker KDLS 100 User Manual
Sterling Fan 88200440000 User Manual
Sterling Plumbing Hot Tub 71041112 User Manual
Suncast Tool Storage RSH125 User Manual
Symantec Patio Umbrella 10024709 User Manual
Tanita Scale BF 542 User Manual