4-248-074-12(1)
Super Audio CD/
DVD RECEIVER
US
FR
Operating instructions
Mode d’emploi
AVD-S500ES
©2003 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
3
WARNING
WARNING
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
Caution – The use of optical instruments
with this product will increase eye
hazard.
For the customers in the U.S.A
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of
electric shock to persons.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
Owner’s Record
Note to CATV system installer:
The model and serial numbers are located at the rear of
the unit. Record the serial number in the space
provided below. Refer to them whenever you call upon
your Sony dealer regarding this product.
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
Model No. AVD-S500ES
Serial No.______________
For the customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
®
ENERGY STAR is a U.S.
registered mark.
®
As an ENERGY STAR partner,
Sony Corporation has determined
that this product meets the
®
ENERGY STAR guidelines for
energy efficiency.
2US
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
Welcome!
Safety
• If anything falls into the cabinet, unplug the unit and
have it checked by qualified personnel before
operating it any further.
Thank you for purchasing this Sony Super
Audio CD/DVD RECEIVER. Before operating
this system, please read this manual thoroughly
and retain it for future reference.
• The unit is not disconnected from the mains as long
as it is connected to the mains outlet, even if the unit
itself has been turned off.
• Unplug the unit from the wall outlet if you do not
intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never by
the cord.
Precautions
On safety
Should any solid object or liquid fall into the cabinet,
unplug the receiver and have it checked by qualified
personnel before operating it any further.
Installing
• Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
On placement
• Allow adequate air circulation to prevent internal
heat buildup.
• Place the receiver in a location with adequate
ventilation to prevent heat build-up in the receiver.
• At high volume, over long periods of time, the cabinet
becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do
not place the unit in a confined space where
ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything
on the receiver. The receiver is equipped with a high
power amplifier. If the ventilation slots on the top
surface are blocked, the unit can overheat and
malfunction.
• Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation slots.
• Do not install the unit near heat sources such as
radiators, or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or
shock.
• Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the unit and discs away from equipment with
strong magnets, such as microwave ovens, or large
loudspeakers.
• Do not place the receiver on a soft surface such as a
rug that might block the ventilation holes on the
bottom.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to a warm
location, moisture may condense inside the receiver
and cause damage to the lenses. When you first install
the unit, or when you move it from a cold to a warm
location, wait for about 30 minutes before operating
the unit.
• Do not place the receiver in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
On operation
• If the receiver is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lenses inside the
receiver. Should this occur, the receiver may not
operate properly. In this case, remove the disc and
leave the receiver turned on for about half an hour
until the moisture evaporates.
• When you move the receiver, take out any disc. If you
don’t, the disc may be damaged.
• For power saving purposes, the receiver can be
completely turned off by the POWER button on the
main unit. Though the LED remains lit for a while,
the receiver is completely off.
continued
3US
Download from Www.Somanuals.com. All Manuals Search And Download.
On adjusting volume
Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is played.
On cleaning
Clean the cabinet, panel, and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning your
receiver, please consult your nearest Sony dealer.
On cleaning discs
Do not use a commercially available CD/DVD
cleaning disc. It may cause a malfunction.
On your TV’s color
If the speakers should cause the TV screen to have
color irregularity, turn off the TV at once then turn it
on after 15 to 30 minutes. If color irregularity should
persist, place the speakers farther away from the set.
The nameplate is located on the rear of the unit.
IMPORTANT NOTICE
Caution: This receiver is capable of holding a still
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
On moving the receiver
When you carry the receiver, use the following
procedure to protect the inner mechanism.
Remove the disc. “NO DISC” is displayed in the front
panel display. Turn off the receiver and remove the AC
power cord from a wall outlet.
4US
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
This receiver Can Play the Following
Selecting the Surround Back Decoding
Changing the Speaker Impedance
Using Various Additional
Step 3: TV and Video Component
Step 4: Connecting the AC Power Cord
(CUSTOM PARENTAL
CONTROL)
Resuming Playback from the Point Where
Playing VIDEO CDs with PBC Functions
Controlling Other Units with the Supplied
Changing the Brightness of the Front
Setting the Display or Sound Track
Searching for a Particular Point on a
Searching for a Title/Chapter/Track/
continued
5US
Download from Www.Somanuals.com. All Manuals Search And Download.
6US
Download from Www.Somanuals.com. All Manuals Search And Download.
Format of
discs
Disc logo
About this Manual
Audio CD
• The instructions in this manual describe the
controls on the remote. You can also use the
controls on the receiver if they have the same
or similar names as those on the remote.
• The following symbols are used in this
manual.
CD-R/CD-RW
(audio data)
(MP3 files)
(JPEG files)
Symbol
Meaning
Functions available for DVD
VIDEOs and DVD-Rs/DVD-RWs
in video mode or DVD+Rs/
DVD+RWs in video mode
The “DVD VIDEO” logo is a trademark.
Functions available in VIDEO CD
mode
Terms for discs
Functions available in CD mode
• Title
The longest section of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software.
Functions available in Super Audio
CD and Audio CD mode
Functions available for MP3* audio
tracks
• Chapter
Functions available for JPEG files
Section of a picture or a music piece that is
smaller than titles. A title is composed of
several chapters. Depending on the disc, no
chapters may be recorded.
* MP3 (MPEG1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio
data.
• Album
Section of a music piece or an image on a data
CD containing MP3 audio tracks or JPEG
files.
This receiver Can Play the
Following Discs
• Track
Section of a picture or a music piece on a
VIDEO CD, Super Audio CD, CD, or MP3.
• Index (Super Audio CD, CD) / Video
Index (VIDEO CD)
Format of
Disc logo
discs
DVD VIDEO
A number that divides a track into sections to
easily locate the point you want on a VIDEO
CD, Super Audio CD or CD. Depending on the
disc, no indexes may be recorded.
• Scene
Super Audio
CD
On a VIDEO CD with PBC functions
(page 26), the menu screens, moving pictures
and still pictures are divided into sections
called “scenes.”
VIDEO CD
• File
Section of a picture on a data CD containing
JPEG image files.
continued
7US
Download from Www.Somanuals.com. All Manuals Search And Download.
• If audio tracks and images in music CD format
or video CD format are recorded in the first
session, only the first session will be played
back.
Disc
DVD
structure
Title
Chapter
Track
Index
Album
Track
Album
File
VIDEO
Disc
Disc
Disc
CD, Super
Audio CD,
or CD
Region code
structure
Your receiver has a region code printed on the
back of the unit and will only play DVDs
labelled with the same region code.
MP3
structure
ALL
DVDs labelled
receiver.
will also play on this
JPEG
structure
If you try to play any other DVD, the message
“Playback prohibited by area limitations.” will
appear on the TV screen. Depending on the
DVD, no region code indication may be given
even though playing the DVD is prohibited by
area restrictions.
Note on PBC (Playback Control)
(VIDEO CDs)
This receiver conforms to Ver. 1.1 and Ver. 2.0
of VIDEO CD standards. You can enjoy two
kinds of playback depending on the disc type.
Examples of discs that the
receiver cannot play
Disc type
You can
The receiver cannot play the following discs:
• CD-ROMs (except for extension “.MP3,”
“.JPG,” or “.JPEG”)
VIDEO CDs
without PBC
functions
Enjoy video playback (moving
pictures) as well as music.
(Ver. 1.1 discs)
• CD-Rs/CD-RWs other than those recorded in
the following formats:
VIDEO CDs
with PBC
functions
(Ver. 2.0 discs) addition to the video playback
functions of Ver. 1.1 discs.
Play interactive software using
menu screens displayed on the
TV screen (PBC Playback), in
– music CD format
– video CD format
– MP3/JPEG format that conforms to
ISO9660* Level 1/Level 2, or its extended
format, Joliet
Moreover, you can play high-
resolution still pictures, if they
are included on the disc.
• Data part of CD-Extras
• DVD-ROMs
About Multi Session CD
• DVD Audio discs
• This receiver can play Multi Session CDs
when an MP3 audio track is contained in the
first session. Any subsequent MP3 audio
tracks recorded in later sessions can also be
played back.
• DVD-RAMs
• DVD-RWs in VR (Video Recording) mode
• DVD+RWs in VR (Video Recording) mode
• Progressive JPEG file
* A logical format of files and folders on CD-ROMs,
defined by ISO (International Standard
Organization)
• This receiver can play Multi Session CDs
when a JPEG image file is contained in the
first session. Any subsequent JPEG image files
recorded in later sessions can also be played
back.
8US
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not load the following discs:
79).
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
• A disc that is neither standard nor circular
(e.g., card, heart, or star shape).
• A disc with paper or stickers on it.
• A disc that has adhesive or cellophane tape still
left on it.
This system incorporates with Dolby* Digital
and Dolby Pro Logic (II) adaptive matrix
surround decoder and the DTS** Digital
Surround System.
* Manufactured under license from Dolby
Notes about CD-R/CD-RW/DVD-R/DVD-RW
(Video mode)/DVD+R/DVD+RW (Video
mode)
In some cases, CD-R/CD-RW/DVD-R/DVD-RW
(Video mode)/DVD+R/DVD+RW (Video mode)
cannot be played on this player due to the recording
quality or physical condition of the disc, or the
characteristics of the recording device and authoring
software.
Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
**Manufactured under license from Digital Theater
Systems, Inc.
“DTS”, “DTS-ES” and “Neo:6” are trademarks of
Digital Theater Systems, Inc.
Notes about Discs
The disc will not play if it has not been correctly
finalized. For more information, see the operating
instructions for the recording device.
Note that discs created in the Packet Write format
cannot be played.
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
Music discs encoded with copyright
protection technologies
• Do not stick paper or tape on the disc.
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with copyright
protection technologies are marketed by some record
companies. Please be aware that among those discs,
there are some that do not conform to the CD standard
and may not be playable by this product.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
Note on playback operations
of DVDs and VIDEO CDs
Some playback operations of DVDs and VIDEO
CDs may be intentionally set by software
producers. Since this receiver plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Also, refer to the
instructions supplied with the DVDs or VIDEO
CDs.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
Wipe the disc from the center out.
Copyrights
This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be
authorized by Macrovision, and is intended for
continued
9US
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
This receiver can only play back a standard
circular disc. Using neither standard nor circular
discs (e.g., card, heart, or star shape) may cause
a malfunction.
Do not use a disc that has a commercially
available accessory attached, such as a label or
ring.
10US
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the Control Menu Display
Use the Control Menu to select a function that you would like to use. The Control Menu display appears
when the DVD DISPLAY button is pressed. For details, refer to the page in parentheses.
Total number of
Currently playing title number (Video CD/ titles or tracks
recorded
Currentlyplaying
title name
Super Audio CD/CD: track number)
Total number of chapters or indexes recorded
Disc name or disc
Playback status
(NPlayback, XPause, xStop, etc.)
type
Currently playing chapter
number (Video CD/Super
Audio CD/CD: index number)
DVD
DVD
Type of disc being
(
)
1 2 2 7 MAKING SCENE
played back
(
)
1 8 3 4
1 : 3 2 : 5 5
Playing time
T
Icon of selected
Control Menu item
1: ENGLISH
2: FRENCH
3: SPANISH
Current setting
Options
Control Menu items
Function name of selected
Control Menu item
SUBTITLE
Select:
ENTER
Operation message
List of Control Menu Items
DISC
Displays the disc name or the disc type inserted into the
receiver.
TITLE (DVD only) (page 35)/
SCENE (only VIDEO CD in PBC playback) /
TRACK (VIDEO CD only) (page 35)
Selects the title (DVD), or the track (VIDEO CD) to be
played.
Displays the scene (VIDEO CD in PBC playback).
played.
INDEX (VIDEO CD only) (page 36)
TRACK (Super Audio CD/CD/MP3 Selects the track (Super Audio CD/CD/MP3) to be played.
INDEX (Super Audio CD/CD only) Displays the index and selects the index (Super Audio CD) to
be played.
Checks the elapsed time and the remaining playback time.
Inputs the time code for picture and music searching.
AUDIO (DVD/VIDEO CD/Super
Changes the audio setting.
Audio CD/CD/MP3 only) (page 42)
SUBTITLE (DVD only) (page 52)
Displays the subtitles.
Changes the subtitle language.
continued
11US
Download from Www.Somanuals.com. All Manuals Search And Download.
DATE (JPEG only) (page 41)
ANGLE (DVD only) (page 51)
Selects the file (JPEG) to be played.
Displays the date information.
Changes the angle.
PLAYMODE (VIDEO CD/Super
Selects the play mode.
Audio CD/CD/MP3/JPEG only) (page 32)
REPEAT (page 33)
Plays the entire disc (all titles/all tracks), one title/chapter/
track/album, or contents of program repeatedly.
PICTURE MODE (DVD/VIDEO
CD/JPEG only) (page 53)
Adjusts the video signal from the receiver in various ways.
Selects the setting that suits the program you are watching.
CUSTOM PARENTAL CONTROL Sets the disc to prohibit playing.
Tips
• Each time you press DVD DISPLAY, the Control Menu display changes as follows:
Control Menu display
m
Control Menu display off
The Control Menu items vary, depending on the disc.
• The Control Menu icon indicator lights up in green
“OFF.”
t
unless you set the REPEAT setting to
• The “ANGLE” indicator lights up in green only when multiple angles are recorded on the disc.
• The “PICTURE MODE” indicator lights up in green if “STANDARD” is not selected.
12US
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting Batteries into
the Remote
Getting Started
Unpacking
You can control the receiver using the supplied
remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to
the markings inside the compartment. When
using the remote, point it at the remote sensor
on the receiver.
Check that you have the following items:
• AM loop antenna (1)
• FM wire antenna (1)
• S Video cord (1)
• Remote Commander (remote) RM-SP500 (1)
• R6 (size AA) batteries (2)
• Operating instructions (1)
Notes
• Do not leave the remote in an extremely hot or humid
place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from
the sun or lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of
time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
• When you operate the receiver, select DVD or
TUNER function.
13US
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Speaker System Hookup
You can enjoy surround sound by connecting 6 speakers (front L/R speakers, center speaker, surround
L/R speakers, surround back speaker) and active subwoofer to the receiver. If you do not connect 6
speakers and active subwoofer to the receiver, the receiver offers the means to optimize the signal
depending on the number of connected speakers. When you connect 2 speakers to the receiver, connect
the speakers to the SPEAKERS FRONT L/R jacks.
Notes
• Be sure to match the speaker cords to their appropriate terminal: 3 to 3, # to #, L to L, and R to R jack.
• Use high performance speakers.
• Use suitable sized speakers of similar performance for the front, center, surround and surround back speakers.
• To obtain the best possible surround sound, specify the speaker parameters (size, distance, level, etc.) on page 70.
14US
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminals for connecting the speakers
Connect
To the
Front speakers
Surround speakers
Surround back speaker
Center speaker
Subwoofer
SPEAKERS FRONT L and R terminals
SPEAKERS SURROUND L and R terminals
SPEAKERS SURROUND BACK terminal
SPEAKERS CENTER terminal
SUBWOOFER AUDIO OUT jack
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
P
B/CB
PR/CR
AM
Y
COAXIAL
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
+
–
Center speaker
–
+
+
–
Subwoofer
(active type)
Front speaker (R)
Front speaker (L)
+
–
+
–
+
–
Surround speaker (L)
Surround speaker (R)
Surround back speaker
continued
15US
Download from Www.Somanuals.com. All Manuals Search And Download.
Note for connecting the speaker cords to the receiver
3
Remove about 10 mm ( /8 inch) of insulation at the end of the cord, then twist the exposed wires.
Connect the stripped ends of the cords to the terminals, taking care to avoid contact between the cords.
Make sure the cords are firmly connected to the speaker and receiver terminals.
10 mm
(3/8 in.)
To avoid short-circuiting the speakers
Short-circuiting of the speakers may damage the receiver. To prevent this, be sure to follow these
precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch
another speaker terminal or the bare wire of another speaker cord.
Examples of poor speaker cord connection
Stripped speaker cord is touching
another speaker terminal.
Stripped cords are touching each other
due to excessive removal of insulation.
After connecting all the components, speakers, and AC power cord (mains lead), output a test tone to
check that all the speakers are connected correctly. For details on outputting a test tone, see page 72.
If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a speaker
other than the one currently displayed in the front panel display, the speaker may be short-circuited. If
this happens, check the speaker connection again.
Notes
• Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the cords
are reversed, the sound will be distorted and will lack bass.
• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on
the speakers.
• When connecting the stripped ends of the speaker cords, make sure the ends do not touch each other or neighbouring
terminals.
16US
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Antenna Hookups
Connect the supplied AM/FM antennas for listening to the radio.
Terminals for connecting the antennas
Connect the
To the
AM loop antenna
FM wire antenna
AM terminals
FM 75ΩCOAXIAL jack
AM loop antenna
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
COAXIAL
P
B/CB
PR/CR
AM
Y
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
FM wire antenna
Notes
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
• When you connect the supplied AM loop antenna, connect the black cord (A) to the U terminal, and the white cord
(B) to the other terminal.
A
AM
B
continued
17US
Download from Www.Somanuals.com. All Manuals Search And Download.
If you have poor FM reception
Use a 75-ohms coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below.
Outdoor FM antenna
Receiver
ANTENNA
FM
75
AM
COAXIAL
Earth wire
(not supplied)
To earth
Note
If you connect the receiver to an outdoor antenna, ground it to protect against lightning. To prevent a gas explosion,
do not connect the earth wire to a gas pipe.
18US
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: TV and Video Component Hookups
Required cords
S Video cord for connecting a TV monitor
Audio/Video cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the
components.
Yellow (Video)
White (L/audio)
Red (R/audio)
Jacks for connecting video components
Connect a
To the
TV monitor
MONITOR (S VIDEO OUT or VIDEO OUT) jack
VIDEO 1 or VIDEO 2 (S VIDEO IN or VIDEO IN/AUDIO L/R IN) jacks
TV/SAT (S VIDEO IN or VIDEO IN/AUDIO L/R IN) jacks
VCR
Digital satellite receiver
Note
When the receiver is not set to “DVD” mode, no signal is output from the COMPONENT VIDEO OUT jacks.
Tip
When using the COMPONENT VIDEO OUT jacks (Y, PB/CB, PR/CR) instead of the S Video jacks or
the Video jacks, your TV monitor must also be connected via COMPONENT VIDEO OUT jacks (Y,
P
B/CB, PR/CR). If your TV accepts progressive format signals, you must use this connection and set
continued
19US
Download from Www.Somanuals.com. All Manuals Search And Download.
TV with
TV with
TV
COMPONENT VIDEO IN jacks
S VIDEO IN jack
COMPONENT
VIDEO IN
INPUT
INPUT
VIDEO
IN
S
VIDEO
IN
Y
PB/CB
PR/CR
IN
IN
IN
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
COAXIAL
P
B/CB
PR/CR
AM
Y
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
OUT
OUT
OUT
OUT
OUT
DIGITAL OUT
(OPTICAL)
S
VIDEO
OUT
S
VIDEO
OUT
AV MULTI OUT
AUDIO
OUT
AUDIO
OUT
L
L
OUTPUT
R
R
OPTICAL
Digital satellite receiver
VCR
PlayStation 2
If you connect a digital satellite receiver with an OPTICAL OUT jack or
a COAXIAL OUT jack
The digital satellite receiver can be connected to the TV/SAT (OPTICAL or COAXIAL) INPUT jack
instead of the AUDIO IN L/R jacks of the receiver.
The receiver can accept both the digital and analogue signals. Digital signals have priority over
analogue signals. If the digital signal ceases, the analogue signal will be processed after 2 seconds.
If you connect a digital satellite receiver without an OPTICAL OUT jack
Connect the digital satellite receiver to the S VIDEO IN or VIDEO IN and AUDIO IN L/R jacks only
of the receiver.
To listen to the TV or game machine (ex: PlayStation 2) sound by using
the receiver
Connect the audio output jacks of the TV or game machine to the VIDEO 2 (AUDIO L/R IN or
OPTICAL IN) jacks of the receiver.
20US
Download from Www.Somanuals.com. All Manuals Search And Download.
When color irregularity occurs on
the TV
Speaker Setup
If speakers are installed too close, color
irregularity may occur on the screen. If color
irregularity occurs, turn off the TV set once, then
turn it on after 15 to 30 minutes. If color
irregularity occurs again, place the subwoofer
farther away from the TV set. If color
irregularity still occurs after performing the
above, make sure that no magnetic object is
placed near the subwoofer. Color irregularity
may occur as a result of interaction between the
subwoofer and the magnetic object.
For the best possible surround sound, all the
speakers other than the subwoofer should be the
same distance from the listening position (A).
However, this receiver allows you to place the
center speaker up to 1.5 metres a) closer (B)
and the surround and the surround back speakers
up to 4.5 metres b) closer (C, D) to the
listening position.
The front speakers can be placed from 0.9 to
6.9 metres c) (A) from the listening position.
Examples of possible sources of magnetic
interference include: magnetic latches on a TV
stand, etc., healthcare devices, toys, etc.
Canadian numerical equivalents:
a) 5 feet (1.5 metres)
b) 15 feet (4.5 metres)
c) 3 to 23 feet (0.9 to 6.9 metres)
Specifying the speaker
parameters
Place speakers as illustrated below
To obtain the best possible surround sound, first
specify the size and the distance of the speakers
from your listening position, then set the level
and balance. Use the test tone to adjust the
speaker level and balance to the same level.
Select “SPEAKER SETUP” in the setup
display. For details, see “Settings for the
B
A
A
45
C
C
90
Also change the impedance value depending on
your speaker’s impedance. For details, see
“Changing the Speaker Impedance Value”
D
20
Note
Do not place the center, surround and the surround
back speakers farther away from the listening position
than the front speakers.
22US
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press Z on the receiver or OPEN/
CLOSE on the remote, and place a disc
with the label side up on the disc tray.
Playing Discs
The receiver automatically turns on and the
STANDBY indicator turns off.
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operation details supplied with your
disc.
STANDBY indicator
When you play an 8 cm disc, place
it on the inner circle of the tray
N x
Z
POWER FUNCTION –/+
5
Press H.
VOLUME
POWER
STANDBY
The disc tray closes, and the receiver starts
playback (continuous play). Adjust the
volume on the receiver.
SOUND FIELD
2CH
A.
F
.
D.
MODE
DISPLAY
TUNER/PRESET
FUNCTION
PHONES
After following Step 5
Depending on the disc, a menu may appear on
the TV screen. You can play the disc
interactively by following the instructions on the
Adjust the
volume
Disc tray
Connect
headphones
"/1
DVD
To remove the disc
Press Z on the receiver or OPEN/CLOSE on the
remote. “OPEN” appears in the front panel
display. Remove the disc after the disc tray
slides out from the receiver.
To turn on the receiver
H
x
Press POWER on the receiver. The receiver
enters standby mode and the STANDBY
indicator lights up in red. Press "/1 on the
remote. The receiver turns on and the
STANDBY indicator turns off. In standby
mode, the receiver also turns on by pressing Z,
FUNCTION –/+ or N on the receiver or by
pressing DVD, OPEN/CLOSE or H on the
remote.
OPEN/CLOSE
1
2
Turn on your TV.
Switch the input selector on the TV to
this receiver.
3
Press POWER on the receiver.
The receiver enters standby mode and the
STANDBY indicator lights up in red.
continued
23US
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the receiver
To
Press
Press "/1 on the remote. The receiver enters
standby mode and the STANDBY indicator
lights up in red. To turn off the receiver
completely, press POWER on the receiver.
While playing a disc, do not turn off the receiver
by pressing POWER. Doing so may cancel the
menu settings. When you turn off the receiver,
first press x to stop playback and then press "/1
on the remote.
Stop play and remove the
disc
Z on the receiver or
OPEN/CLOSE on the
remote.
Mute the sound
MUTING. To cancel
muting; press it again
or VOLUME + to
adjust the sound
volume.
* You cannot pause during JPEG playback.
Saving power in standby mode
Press "/1 on the remote once.
Notes
• Do not push the disc tray when closing it. Press Z on
the receiver or OPEN/CLOSE on the remote to close
the disc tray.
Tip
While the receiver is in standby mode, the STANDBY
indicator on the receiver lights up.
• If DVD playback is paused for approximately one
hour, the receiver automatically turns off.
To cancel standby mode
Press "/1 on the remote once.
Additional operations
./>
x
H
X
OPEN/
CLOSE
VOLUME +/–
MUTING
To
Press
x
Stop
Pause*
X
Resume play from pause
X or H
>
Go to the next chapter,
track, scene, or file in
continuous play mode
Go back to the preceding
chapter, track, scene, or file
in continuous play mode
.
24US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
To play from the beginning of the disc, press x twice,
then press H.
Resuming Playback from
the Point Where You
Stopped the Disc
(Resume Play)
When you stop the disc, the receiver remembers
the point where you pressed x and “RESUME”
appears in the front panel display. As long as
you do not remove the disc, Resume Play will
work even if the receiver enters standby mode
by pressing "/1.
H
x
1
2
While playing a disc, press x to stop
playback.
“RESUME” appears in the front panel
display, so you can restart the disc from the
point where you stopped the disc.
If “RESUME” does not appear, Resume
Play is not available.
Press H.
The receiver starts playback from the point
where you stopped the disc in Step 1.
Notes
• Depending on where you stop the disc, the receiver
may not resume playback from exactly the same
point.
• The point where you stopped playing is cleared if:
– you change the play mode.
– you change the setting on the Setup Menu.
25US
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the DVD’s Menu
Playing VIDEO CDs with
PBC Functions (Ver. 2.0)
(PBC Playback)
A DVD is divided into long sections, which
make up a picture or music feature. These
sections are called “titles.” When you play a
DVD which contains several titles, you can
select the title you want using TOP MENU/
GUIDE.
When you play DVDs that allow you to select
items such as the language for the subtitles and
the language for the sound, select these items
using AV MENU.
With PBC (Playback Control) functions, you
can enjoy simple interactive operations, search
functions, and other such operations.
PBC playback allows you to play VIDEO CDs
interactively by following the menu on the TV
screen.
Number
buttons
Number
buttons
./>
H
x
TOP
MENU/
AV MENU
GUIDE
ENTER
C/X/x/c
ENTER
X/x
O RETURN/
EXIT
1
2
Start playing a VIDEO CD with PBC
functions.
1
Press TOP MENU/GUIDE or AV MENU.
The menu for your selection appears.
The disc’s menu appears on the TV screen.
The contents of the menu vary from disc to
disc.
Select the item number you want by
pressing X/x or the number buttons.
2
3
Press C/X/x/c or the number buttons to
select the item you want to play or
change.
3
4
Press ENTER.
Follow the instructions in the menu for
interactive operations.
Press ENTER.
Refer to the operation details supplied with
the disc, as the operating procedure may
differ, depending on the VIDEO CD.
Note
If the DVD top menu or a DVD menu is displayed
during DVD playback for approximately one hour, the
receiver automatically turns off.
To go back to the menu
Press O RETURN/EXIT.
26US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• Depending on the VIDEO CD, the menu does not
appear in Step 1.
Playing an MP3 Audio
Track
• Depending on the VIDEO CD, “Press ENTER” in
Step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case, press
H.
You can play MP3 audio tracks on CD-ROMs,
CD-Rs, or CD-RWs. However, the discs must be
recorded according to ISO9660 level 1, level 2,
or Joliet format for the receiver to recognize the
tracks. You can also play discs recorded in Multi
Session. See the instructions of the CD-R/RW
device or recording software (not supplied) for
details on the recording format.
Tip
To play without using PBC, press ./> or the
number buttons while the receiver is stopped to select
a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and the
receiver starts continuous play. You cannot play still
pictures such as a menu. To return to PBC playback,
press x twice, then press H.
1
2
Load a data disc recorded in MP3 into
the receiver.
Press H.
The receiver starts to play the first MP3
audio track in the first album on the disc.
Notes
• The receiver can play MP3 (MPEG1 Audio Layer3)
audio. The receiver cannot play audio tracks in
MP3PRO format.
• This receiver can play Multi Session CDs when an
MP3 audio track is located in the first session. Any
subsequent MP3 audio tracks, recorded in the later
sessions, can also be played back.
• Maximum number of albums on a disc: 99
(The maximum number of MP3 audio tracks that can
be contained in an album is 250.)
• An album that does not include an MP3 audio track is
skipped.
• If you put the extension “.MP3” to data not in MP3
format, the receiver cannot recognize the data
properly and will generate a loud noise which could
damage your speaker system.
• If the receiver cannot play MP3, remove the disc and
select “CUSTOM SETUP” from the setup items.
Then select “DATA CD PRIORITY” and set to
• The receiver can play to a depth of 8 directories.
continued
27US
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Select
and press ENTER.
(TRACK) using X/x
Selecting an album and track
The list of tracks contained in the current
album appears.
HOME TOWN
ROCK BEST HIT
MP3
1.HIGHWAY
ALBUM–
ALBUM+
2.VIEW POINT
3.MY CHILDREN
4.DANCING
ENTER
5.GOOD TASTE
6.DESTINATION
7.MARATHON
8.PLACE-KICK
9.TAKE IT EASY
10.PORT TOWER
11.STANDARD
C/X/x/c
O RETURN/
EXIT
DVD
DISPLAY
When the list of all tracks or albums cannot
be displayed on the window, the jump bar
appears. Press c to select the jump bar icon,
and then scroll the jump bar to display the
rest of the list using X/x. Press C or O
RETURN/EXIT to return to the track or the
album list.
1
2
Press DVD DISPLAY.
The Control Menu and name of the MP3
data disc appear.
5
Select a track using X/x and press
ENTER.
Press X/x to select
then press ENTER or c.
(ALBUM)
The selected track starts playing.
The list of albums contained in the disc
appears.
To return to the previous display
Press O RETURN/EXIT or C.
HOME TOWN
MP3
ROCK BEST HIT
KARAOKE
JAZZ
R&B
MY FAVORITE SONGS
CLASSICAL
SALSA OF CUBA
BOSSANOVA
To turn off the Control Menu
Press DVD DISPLAY.
Notes
• Only alphabetical letters and numbers can be used for
album or track names. Anything else is displayed as
“ ”.
• If the MP3 file you play back has an ID3 tag, the ID3
tag information is displayed as a track name.
• ID3 tag applies only to version 1.
• If an MP3 file of VBR (variable bit rate) is played,
indicated elapsed time may be different from the
actual time.
3
Select an album you want to play using
X/x and press ENTER.
Tip
When an MP3 data disc is inserted, you can select an
album using the ALBUM– or ALBUM+ on the
remote.
28US
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an album and file
Playing JPEG Image Files
You can play JPEG image files on CD-ROMs,
CD-Rs, or CD-RWs. However, the discs must be
recorded according to ISO9660 level 1, level 2
or Joliet format for the receiver to recognize the
files. You can also play discs recorded in Multi
Session. See the instructions of the CD-R/RW
device or recording software (not supplied) for
details on the recording format.
ALBUM–
ALBUM+
ENTER
C/X/x/c
O RETURN/
EXIT
DVD
DISPLAY
1
2
Load a data disc recorded in JPEG into
the receiver.
Press H.
The receiver starts to play the first JPEG
image file in the first album on the disc.
1
2
Press DVD DISPLAY.
The Control Menu and name of the JPEG
data disc appear.
Notes
• The receiver can play the extension “.JPG” or
“.JPEG.”
Press X/x to select
then press ENTER or c.
(ALBUM)
• The receiver can play Multi Session CDs.
• Maximum number of albums on a disc: 99
(The maximum number of JPEG image files that can
be contained in an album is 250.)
The list of albums contained in the disc
appears.
MOUNTAIN
JPEG
FAMILY
FLOWER
GARDEN
TRAIN
• An album that does not include a JPEG file is
skipped.
• When the receiver cannot play JPEG, remove the disc
and select “CUSTOM SETUP” from the setup items.
Then select “DATA CD PRIORITY” and set to
• A JPEG image file of a length or width of more than
4,720 dots cannot be played.
CAR
3
4
Select an album you want to play using
X/x and press ENTER.
• Some CD-Rs or CD-RWs cannot be played on this
receiver depending on file format.
Select
press ENTER.
(FILE) using X/x and
• The receiver can play to a depth of 8 directories.
• Progressive JPEG image files cannot be played on
this receiver.
The list of files contained in the current
album appears.
MOUNTAIN
FAMILY
JPEG
1.HAPPY
2.BIRTHDAY
3.CELEBRATION
4.CHRISTMAS
5.MOM
6.BASEBALL
7.PARTY
8.DAD
9.TRAVEL
10.FRIEND
11.DRIVE
continued
29US
Download from Www.Somanuals.com. All Manuals Search And Download.
When the list of all files or albums cannot
be displayed on the window, the jump bar
appears. Press c to select the jump bar icon,
and then scroll the jump bar to display the
rest of the list using X/x. Press C or O
RETURN/EXIT to return to the file or the
album list.
To change the interval time of
Slide Show
Each time you press M during Slide Show, the
interval time changes. With each press, the
indication changes as follows:
FF1M t FF2M t FF3M
5
Select a file using X/x and press
ENTER.
FF3M interval time is faster than FF2M.
The selected file starts playing.
Note
Slide Show can play in only one direction.
To return to the previous display
Press O RETURN/EXIT or C.
To rotate the current image
To turn off the Control Menu
Press DVD DISPLAY.
Note
Only alphabetical letters and numbers can be used for
album or file names. Anything else is displayed as “ ”.
H
Tip
When a JPEG data disc is inserted, you can select an
album using the ALBUM– or ALBUM+ on the
remote.
C/c
Enjoying Slide Show on a
JPEG data disc
M
Rotate the current image using C/c
H
Each time you press c, the image turns
clockwise by 90°.
Each time you press C, the image turns
counterclockwise by 90°.
Note
You cannot rotate an image during Slide Show. Press
H to return to normal play before this operation.
1
2
Press M while displaying a JPEG
image.
Slide Show starts from the current image.
Press H when you want to exit Slide
Show.
Return to normal play from the current
image.
30US
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press c.
Creating Your Own
Program
The cursor moves to the track (in this case,
“1”). Before programming the MP3 tracks,
it is required to select the album.
(Program Play)
Program
1
2
3
4
Total Time 0:00
Track
1
2
3
4
5
6
7
8
9
TRACK1
TRACK2
TRACK3
TRACK4
TRACK5
TRACK6
TRACK7
TRACK8
TRACK9
5
6
You can play the contents of a disc in the order
you want by arranging the order of the tracks on
the disc to create your own Program. You can
program up to 25 steps.
7
8
9
10
10 TRACK10
When the list of all tracks cannot be
displayed on the window, the jump bar
appears. Press c to select the jump bar icon,
and then scroll the jump bar to display the
rest of the list using X/x. Press C or O
RETURN/EXIT to return to the track list.
PLAY
MODE
REPEAT
Number
buttons
3
4
Select the track you want to program.
CLEAR
For example, select track “7.”
Program
Total Time 0:00
H
1
2
Track
1
2
3
4
5
6
7
8
9
TRACK1
TRACK2
TRACK3
TRACK4
TRACK5
TRACK6
TRACK7
TRACK8
TRACK9
3
ENTER
C/X/x/c
4
5
6
7
8
9
10
O RETURN/
EXIT
10 TRACK10
1
In stop mode, press PLAY MODE
repeatedly until “PROGRAM” appears
in the front panel display.
Press X/x or the number buttons to
select “7” then press ENTER.
The program menu appears on the TV
screen.
Total time of the programmed
tracks (except MP3)
Program
1
2
3
4
Total Time 12:34
Program
1
2
3
4
Total Time 0:00
TRACK7
5
5
6
6
7
7
8
9
10
8
9
10
5
To program other tracks, repeat Steps
2 to 4.
The programmed tracks are displayed in the
selected order.
continued
31US
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press H to start Program Play.
Playing in Random Order
(Shuffle Play)
Program Play begins.
When the program ends, you can restart the
same program again by pressing H.
Other Operations
You can have the receiver “shuffle” tracks and
play them in random order. Subsequent
“shuffling” will produce a different playing
order.
To
Do this
Return to normal Press CLEAR during playback.
play
Turn off the
program menu
In stop mode, press PLAY MODE
to turn off the program menu.
Cancel the
programmed
order
Press CLEAR while the program
window is displayed and the last
program is cancelled.
PLAY
MODE
Notes
• The Program Play function is not available for DVDs
and JPEG.
CLEAR
• When you Program MP3 tracks, “--:--” is displayed
as the total time of the programmed tracks.
• When you remove the disc, Program Play is cancelled
and the program you created is cleared.
H
Tip
You can perform Repeat Play of programmed tracks.
Press REPEAT, or set “REPEAT” to “ALL” in the
1
2
In stop mode, press PLAY MODE
repeatedly until “SHUFFLE” appears in
the front panel display.
When you play an MP3 disc, you can play
all tracks in albums in random order.
Press H.
To return to normal play
In stop mode, press PLAY MODE three times to
cancel SHUFFLE or twice to cancel SHUFFLE
(ALBUM). Or during playback, press CLEAR
to return to normal play.
32US
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the shuffle mode in
the Control Menu
Playing Repeatedly
(Repeat Play)
You can select either normal shuffle or album
shuffle (MP3 only).
You can play all the titles/tracks/files or a single
title/chapter/track/album on a disc.
In Shuffle or Program Play mode, the receiver
repeats tracks in shuffled or programmed order.
You cannot perform Repeat Play during PBC
H
ENTER
X/x
DVD
DISPLAY
REPEAT
CLEAR
1
2
Press DVD DISPLAY.
The Control Menu appears.
H
Press X/x to select
MODE), then press ENTER.
(PLAY
ENTER
X/x
HOME TOWN
8 ALBUM
MP3
DVD
DISPLAY
:
CONTINUE
CONTINUE(ALBUM)
SHUFFLE
SHUFFLE(ALBUM)
PROGRAM
1
2
Press DVD DISPLAY.
The Control Menu appears.
Press X/x to select
(REPEAT), then press ENTER.
3
4
Select SHUFFLE or SHUFFLE (ALBUM)
using X/x and press ENTER.
If you do not select “OFF,” the “REPEAT”
indicator lights up in green.
SHUFFLE: Plays tracks on the disc in
random order.
3
Select the Repeat Play setting, then
press ENTER.
SHUFFLE (ALBUM): Plays tracks from a
selected album in random order.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
Press H.
1 8 3 4
T
1 : 3 2 : 5 5
The selected Shuffle Play begins.
Note
OFF
ALL
TITLE
Shuffle Play is cancelled when you eject the disc. The
play mode changes in the following sequence:
SHUFFLE t CONTINUE
CHAPTER
SHUFFLE (ALBUM) t CONTINUE (ALBUM)
continued
33US
Download from Www.Somanuals.com. All Manuals Search And Download.
x When playing a DVD
• OFF: does not play repeatedly.
• ALL: repeats all the titles.
• TITLE: repeats the current title on a
disc.
Searching for a Particular
Point on a Disc
(Scan, Slow-motion Play)
• CHAPTER: repeats the current
chapter.
x When playing a VIDEO CD/Super
Audio CD/CD/MP3, and when Program
Play is set to OFF
You can locate a particular point on a disc
quickly by monitoring the picture or by playing
back slowly.
• OFF: does not play repeatedly.
• ALL: repeats all the tracks on the disc,
or repeats the current album (only
when CONTINUE (ALBUM) or
SHUFFLE (ALBUM) in the play
mode is selected).
• TRACK: repeats the current track.
x When playing a JPEG
• OFF: does not play repeatedly.
• ALL: repeats all the files on the disc
(when CONTINUE is selected in the
play mode), or repeats the current
album (when CONTINUE (ALBUM)
is selected in the play mode).
m/M
/y
y
H
x When Program Play is set to ON
• OFF: does not play repeatedly.
• ALL: repeats Program Play.
Notes
• Depending on the DVD/VIDEO CD, you may not be
able to perform some of the operations described.
• During scan or slow-motion play, no sound is output.
To cancel Repeat Play
Press CLEAR.
Notes
• Depending on the DVD disc, repeat play does not
work.
Locating a point quickly by
playing a disc in fast forward
or fast reverse (Scan)
• Repeat Play is cancelled when you eject the disc.
• If “ALL” is selected, repeat play is limited to 5 times.
1
2
Press m or M while playing a disc.
Tips
• You can set Repeat Play during stop mode.
After selecting the “REPEAT” item, press H.
The receiver starts Repeat Play.
• You can quickly display the “REPEAT” status.
Press REPEAT on the remote.
When you find the point you want,
press H to return to normal speed.
• You can perform Repeat Play for DVD titles that
contain chapters.
34US
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the scan speed (DVD/
VIDEO CD only)
Each time you press m or M during scan, the
playback speed changes. Two speeds are
available. With each press, the indication
changes as follows:
Searching for a Title/
Chapter/Track/Index/
Album/File
Playback direction
FF1M t FF2M
You can search a title (DVD), chapter (DVD),
track (CD, VIDEO CD, Super Audio CD, MP3),
index (VIDEO CD, Super Audio CD), album
(MP3, JPEG), and file (JPEG). As titles, tracks,
albums and files are assigned individual names
on the disc, you can select the desired one from
the Control Menu. Also chapters and indexes are
assigned individual numbers on the disc, so you
select the desired one by entering its number. Or
you can search a particular point using the time
code (TIME SEARCH).
Opposite direction
FR1m t FR2m
FF2M/FR2m playback speed is faster than
FF1M/FR1m.
Watching frame by frame
(Slow-motion play)
(DVD/VIDEO CD only)
y
Press
or y when the receiver is in the
pause mode.
To return to normal speed, press H.
Number
buttons
To change the speed of Slow-
CLEAR
motion play
Each time you press
y
or y during Slow-
motion play, the playback speed changes. Two
speeds are available. With each press, the
indication changes as follows:
ENTER
C/X/x/c
Playback direction
SLOW 2y t SLOW 1y
DVD
DISPLAY
O RETURN/
EXIT
Opposite direction (DVD only)
SLOW 2 t SLOW 1
y
y
Searching for a title/track/
album/file
y
1
Press DVD DISPLAY.
SLOW 2y/SLOW 2 playback speed is
y
The Control Menu appears.
slower than SLOW 1y/SLOW 1
.
2
Press X/x to select the search method,
then press ENTER.
continued
35US
Download from Www.Somanuals.com. All Manuals Search And Download.
x When playing a DVD
Searching for a chapter/index
(TITLE)
1
Press DVD DISPLAY.
x When playing a VIDEO CD
The Control Menu appears.
(TRACK)
2
Press X/x to select the search method.
x When playing a Super Audio CD
x When playing a DVD
(TRACK)
(CHAPTER)
x When playing a CD
x When playing a VIDEO CD
(TRACK)
(INDEX)
x When playing an MP3
x When playing a Super Audio CD
(ALBUM) or
(TRACK)
(INDEX)
x When displaying a JPEG file
Example: when you select
(CHAPTER)
(ALBUM) or
(FILE)
“** (**)” is selected (** refers to a
number).
The number in parentheses indicates the
total number of titles, chapters, tracks, or
indexes.
Example: when you select
(TRACK)
The list of tracks contained in the disc
appears.
GREATEST HITS
CD
DVD
1.HIGHWAY
2.VIEW POINT
3.MY CHILDREN
4.DANCING
5.GOOD TASTE
6.DESTINATION
7.MARATHON
8.PLACE-KICK
9.TAKE IT EASY
10.PORT TOWER
11.STANDARD
12.LADY
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
T
When the list of all tracks cannot be
displayed on the window, the jump bar
appears. Press c to select the jump bar icon,
and then scroll the jump bar to display the
rest of the list using X/x. Press C or O
RETURN/EXIT to return to the track list.
3
4
Press ENTER.
“** (**)” changes to “-- (**).”
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
– – 3 4
1 : 3 2 : 5 5
T
GREATEST HITS
CD
13.STAY
14.BAD
15.BEAUTIFUL
16.HOLD.ME
17.FIRST TIME
18.BLUE SKY
19.OUR EARTH
20.NO NAME
21.SWEETEST
22.KISS ME
23.FIRE
Press X/x or the number buttons to
select the chapter or index number you
want to search.
24.ANGEL
3
Press X/x to select the desired track,
then press ENTER.
If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
The receiver starts playback from the
selected track.
36US
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press ENTER.
Viewing Disc Information
The receiver starts playback from the
selected number.
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
Viewing the Playing Time and
Remaining Time in the Front
Panel Display
To search for a particular point
using the time code (TIME
SEARCH)
Example: If you search for the playing time of
the current title on a DVD.
You can check disc information, such as the
remaining time, total number of titles in a DVD,
or tracks in a Super Audio CD, CD, VIDEO CD
1 In Step 2, select
(TIME).
“T **:**:**” (playing time of the current title)
is selected.
2 Press ENTER.
“T--:--:--” appears above “T**:**:**.”
DISPLAY/
JUMP
3 Input the time code using the number
buttons, then press ENTER.
For example, to find a desired point at 2
hours, 10 minutes, and 20 seconds after the
beginning, just enter “2:10:20.”
Notes
• The title, chapter or track number displayed on the
TV screen is recorded data in the disc.
• You cannot search a scene of a VIDEO CD.
• If you play a DVD, input the playing time of the
current title using the time code. If you play a CD,
Super Audio CD, VIDEO CD, or MP3, input the
playing time of the current track using the time code.
Press DISPLAY/JUMP.
Each time you press DISPLAY/JUMP while
playing the disc, the display changes as shown in
the charts.
Tip
You can change the display to show playing time or
remaining time. For details, see “Checking the Playing
Time and Remaining Time in the Control Menu”
continued
37US
Download from Www.Somanuals.com. All Manuals Search And Download.
When playing a DVD
Playing time and number of the current title
When playing a VIDEO CD
(without PBC functions), Super
Audio CD or CD
Playing time and current track number (When
playing a CD)
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
dB PCM DSD NEO:6
kHz DTS-ES 96/24
MHz MPEG-2 AAC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
Remaining time of the
current title
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Remaining time of the
current track
Playing time and number
of the current chapter
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Playing time of the disc
Remaining time of the
current chapter
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Remaining time of the
disc
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
Title name*
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Track name*
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
38US
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips
When playing an MP3
Playing time and current track number
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
• When playing VIDEO CDs with PBC functions, only
the playing time of the scene is displayed.
• The playing time and remaining time of the current
chapter, title, track, scene, or disc will also appear on
your TV screen. See the following section “Checking
the Playing Time and Remaining Time” for details on
how to read this information.
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Remaining time of the
current track
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
ALL 1DISCS
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Track (file) name
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Album (folder) name
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
When playing a JPEG
Current file number
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
dB PCM DSD NEO:6
REPEAT1 FM AM
PROGRAM MEMORY
kHz DTS-ES 96/24
MHz MPEG-2 AAC
File name
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Album (folder) name
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
* “NO TEXT” appears if name information does not
exist.
Notes
• Depending on the type of disc being played and the
playing mode, the disc information may not be
displayed.
• ID3 tag applies only to version 1.
• If the MP3 file you play back has an ID3 tag, the ID3
tag information is displayed as a track name.
• Only alphabetical letters and numbers can be used for
album or track names. Anything else is displayed as
“ ”.
• In the following cases, elapsed playing time and
current track remaining time may not be displayed
accurately.
– when an MP3 file of VBR (variable bit rate) is
played.
continued
39US
Download from Www.Somanuals.com. All Manuals Search And Download.
• C **:**:**
Playing time of the current chapter
• C–**:**:**
Remaining time of the current chapter
• **:**:**
Playing time of the menu or current
title without a chapter
Checking the Playing Time
and Remaining Time in the
Control Menu
You can check the playing time and remaining
time of the current title, chapter, or track, and the
total playing time or remaining time of the disc.
You can also check the DVD/CD/Super Audio
CD text and MP3 folder name/file name/ID3 tag
(only song title) recorded on the disc.
x When playing a VIDEO CD (with PBC
functions)
• **:**
Playing time of the current scene
x When playing a VIDEO CD (without
PBC functions), Super Audio CD or CD
• T **:**
Playing time of the current track
DISPLAY/
JUMP
• T–**:**
Remaining time of the current track
• D **:**
Playing time of the current disc
• D–**:**
Remaining time of the current disc
x When playing an MP3
• T **:**
DVD
DISPLAY
Playing time of the current track
• T–**:**
Remaining time of the current track
1
2
Press DVD DISPLAY during playback.
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
The Control Menu appears.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
Notes
T
Disc type
• Only alphabetical letters and numbers can be
displayed.
Time information
• Depending on the type of disc being played, the
receiver can only display a limited number of
characters. Also, depending on the disc, not all text
characters will be displayed.
Press DISPLAY/JUMP repeatedly to
change the time information.
The display and the kinds of time that you
can check depend on the disc you are
playing.
x When playing a DVD
• T **:**:**
Playing time of the current title
• T–**:**:**
Remaining time of the current title
40US
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the date
information (JPEG only)
You can check the date information during
playback when the Exif* tag is recorded in the
JPEG image data.
DVD
DISPLAY
Press DVD DISPLAY during playback.
The Control Menu appears.
MOUNTAIN
JPEG
FAMILY
(
) BIRTHDAY
2 0
1
01 / 01 / 2003
Date information
* “Exchangeable Image File Format” is a digital
camera image format defined by the Japan
Electronics & Information Technology Industries
Association.
Note
If there is no date information or data is damaged on
the disc, the receiver cannot display the date
information.
Tip
You can change the date information order in JPEG
DATE of CUSTOM SETUP (page 70).
41US
Download from Www.Somanuals.com. All Manuals Search And Download.
The options for AUDIO appear.
DVD
DVD
Sound Adjustments
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
T
Changing the Sound
1: ENGLISH
2: FRENCH
3: SPANISH
If a DVD is recorded with multilingual tracks,
you can select the language you want while
playing the DVD.
3
Press X/x to select the desired audio
signal.
If the DVD is recorded in multiple audio formats
(PCM, Dolby Digital, MPEG audio, or DTS),
you can select the audio format you want while
playing the DVD.
x When playing a DVD
Depending on the DVD, the choice of
language varies.
When 4 digits are displayed, they represent
the language code. Refer to the language
the code represents. When the same
language is displayed two or more times,
the DVD is recorded in multiple audio
formats.
With stereo CDs, VIDEO CDs or MP3, you can
select the sound from the left and right channel
and listen to the sound of the selected channel
through both the left and right speakers (in this
case, the sound loses its stereo effect). For
example, when playing a disc containing a song
with the vocals on the right channel and the
instruments on the left channel, you can select
the left channel and hear only the instruments
from both speakers.
x When playing a VIDEO CD, CD, or
MP3
The default setting is underlined.
• STEREO: The standard stereo sound
• 1/L: The sound of the left channel
(monaural)
• 2/R: The sound of the right channel
(monaural)
AUDIO
x When playing a Super Audio CD
In stop mode, depending on the Super
Audio CD, the choice of settings varies.
• MULTI: The disc has a multi-channel
playback area.
• 2CH: The disc has a 2 channel
playback area.
ENTER
X/x
DVD
DISPLAY
• CD: When you want to play the disc as
a conventional CD.
Note
Not all discs give you the three choices above
when in Super Audio CD playback. It all depends
on the layer configuration of the Super Audio CD
to be played.
1
2
Press DVD DISPLAY during playback.
The Control Menu is displayed.
Press X/x to select
(AUDIO),
then press ENTER.
4
Press ENTER.
42US
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
The display examples are as
follows:
• PCM (stereo)
Notes
PROGRAM FORMAT
PCM 48kHz 24bit
• For discs not in multiple audio format, you cannot
change the sound.
• During DVD playback, the sound may change
automatically.
• Dolby Surround
Tip
PROGRAM FORMAT
DOLBY DIGITAL 2/0
You can select “AUDIO” directly by pressing AUDIO.
Each time you press the button, the item changes.
DOLBY SURROUND
• Dolby Digital 5.1ch
Displaying the audio
information of the disc
(DVD only)
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
• DTS
When you select “AUDIO,” the channels being
played are displayed on the screen.
PROGRAM FORMAT
DTS 3/2.1
For example, in Dolby Digital format, multiple
signals ranging from monaural to 5.1 channel
signals can be recorded on a DVD. Depending
on the DVD, the number of recorded channels
may differ.
Tips
• When the signal contains surround signal
components such as LS, RS, or S, the surround effect
is enhanced.
Current audio format*
• If you play MPEG AUDIO sound tracks, the receiver
outputs PCM (stereo) signals.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
• Even though the audio stream contains a surround
back component, the surround back channel is not
displayed.
(
)
1 8 3 4
1 : 3 2 : 5 5
1: ENGLISH
T
Dolby Digital-EX or DTS-ES source is displayed as
“3/2.1”on the screen
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
* “PCM,” “MPEG,” “DTS,” or “DOLBY
DIGITAL” is displayed.
For “DOLBY DIGITAL,” the channels in the
playing track are displayed numerically as
follows:
For Dolby Digital 5.1 ch:
Surround component 2
DOLBY DIGITAL 3 / 2.1
Front component 2 +
Center component 1
LFE (Low Frequency
Effect) component 1
43US
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound field
Display
Enjoying Surround Sound
AUTO FORMAT DIRECT
AUTO
A.F.D. AUTO
Using only the front speaker
(2 CHANNEL STEREO)
You can take advantage of surround sound
simply by selecting one of receiver’s pre-
programmed sound fields. They bring the
exciting and powerful sound of movie theatres
into your home.
To select sound field, press A.F.D., 2CH, or
MODE on the remote repeatedly until the sound
field you want appears in the front panel display.
This mode outputs the sound from the front left
and right speakers. Standard two channel
(stereo) sources completely bypass the sound
field processing. Multi channel surround
formats are downmixed to two channels.
This allows you to play any source using only
the front left and right speakers.
Automatic decoding of the
audio input signal (AUTO
FORMAT DIRECT AUTO)
2CH
The auto decoding function automatically
detects the type of audio signal being input
(Dolby Digital, DTS, or standard 2 channel
stereo) and performs the proper decoding if
necessary. This mode presents the sound as it
was recorded/encoded, without adding any
effects (e.g. reverberation).
However, if there are no low frequency signals
(Dolby Digital LFE, etc.), it will generate a low
frequency signal for output to the subwoofer.
A.F.D.
Press 2CH on the remote.
“2CH STEREO” appears in the front panel
display.
Sound field
Display
2CHANNEL STEREO
2CH STEREO
Press A.F.D. on the remote repeatedly until
“A.F.D. AUTO” appears in the front panel
display.
44US
Download from Www.Somanuals.com. All Manuals Search And Download.
x Neo:6 Music
Selecting a sound field
(A.F.D.button)
Performs the DTS Neo:6 Music mode decoding.
This setting is ideal for standard stereo sources,
such as CDs.
Advanced setting
When a DTS 96/24 signal is input, you can
change the sampling frequency.
A.F.D.
ENTER
X/x
AMP MENU
Press A.F.D. on the remote repeatedly until
the sound field you want appears in the
front panel display.
1
2
3
Press AMP MENU.
Set the function of the remote to DVD, and
then press AMP MENU.
Sound field
Display
PRO LOGIC
PRO LOGIC
PLII MOVIE
PLII MUSIC
NEO:6 CIN
NEO:6 MUS
Press X/x repeatedly until “dts 96/24”
appears in the front panel display, then
press ENTER.
PRO LOGIC II MOVIE
PRO LOGIC II MUSIC
Neo:6 Cinema
Press X/x to select “96/24 AUTO” then
press ENTER or AMP MENU.
Neo:6 Music
• AUTO: When a DTS 96/24 signal is input,
it is played back at the 96 kHz sampling
frequency.
• OFF: Even when a DTS 96/24 signal is
input, it is played back at the 48 kHz
sampling frequency.
x PRO LOGIC
Performs Dolby Pro Logic decoding. A source
recorded in 2 channels is decoded into 4
channels.
x PRO LOGIC II MOVIE
Performs Dolby Pro Logic II Movie mode
decoding. This setting is ideal for movies
encoded in Dolby Surround. In addition, this
mode can reproduce sound in 5.1 channel when
watching videos of old movies or with dubbed
language.
Notes
• When the input signal is a multi-channel source, PRO
LOGIC, PRO LOGIC II MOVIE/MUSIC, and Neo:6
Cinema/Music are cancelled and the multi channel
source is output directly.
• Neo:6 Cinema/Music mode decoding is not available
for DTS 2channel signal.
• When decoding by DTS 96/24 (except A.F.D. mode)
in the sound field, output signals will be converted to
48 kHz (sampling frequency).
• When any speaker is set to “SMALL” or subwoofer
is set to “NONE” in the speaker setting, output
signals will be converted to 48 kHz (sampling
frequency).
x PRO LOGIC II MUSIC
Performs Dolby Pro Logic II Music mode
decoding. This setting is ideal for standard
stereo sources, such as CDs.
x Neo:6 Cinema
Performs the DTS Neo:6 Cinema mode
decoding.
continued
45US
Download from Www.Somanuals.com. All Manuals Search And Download.
x C.ST.EX A (Cinema Studio EX A)
Reproduces the sound characteristics of the
Sony Pictures Entertainment “Cary Grant
Theater” cinema production studio. This is a
standard mode, great for watching most any type
of movie.
Selecting a sound field
(MODE button)
MODE
x C.ST.EX B (Cinema Studio EX B)
Reproduces the sound characteristics of the
Sony Pictures Entertainment “Kim Novak
Theater” cinema production studio. This mode
is ideal for watching science-fiction or action
movies with lots of sound effects.
x C.ST.EX C (Cinema Studio EX C)
Reproduces the sound characteristics of the
Sony Pictures Entertainment scoring stage. This
mode is ideal for watching musicals or classic
films where music is featured in the soundtrack.
x V.M.DIM (VIRTUAL MULTI DIMENSION) *
Uses 3D sound imaging to create an array of
virtual surround speakers positioned higher than
listener from a single pair of actual surround
speakers. This mode creates 5 sets of virtual
speakers surrounding the listener at
Press MODE on the remote repeatedly until
the sound field you want appears in the
front panel display.
FOR MOVIE
approximately a 30º angle of elevation.
Sound field
Display
* “VIRTUAL” sound field: Sound field with virtual
speakers.
CINEMA STUDIO EX A
CINEMA STUDIO EX B
CINEMA STUDIO EX C
V.MULTI DIMENSION
C.ST.EX A*
C.ST.EX B*
C.ST.EX C*
V.M.DIM
About Cinema Studio EX
Cinema Studio EX is ideal for enjoying the
movie software encoded with multi channel
format, such as the Dolby Digital DVD. This
mode reproduces the sound characteristics of
Sony Pictures Entertainment’s studios.
Cinema Studio EX consists of the following
three elements.
* Use DCS Technology
About DCS (Digital Cinema
Sound)
In collaboration with Sony Pictures
Entertainment, Sony measured the sound
environment of their studios and integrated the
data of the measurement and Sony’s own DSP
(Digital Signal Processor) technology to
develop “Digital Cinema Sound.” “Digital
Cinema Sound” simulates in a home theatre an
ideal movie theatre sound environment based on
the preference of the movie director.
• Virtual Multi Dimension
Creates 5 sets of virtual speakers surrounding
the listener from a single pair of actual
surround speakers.
• Screen Depth Matching
In a movie theatre, sound seems to come from
inside the image reflected on the movie screen.
This element creates the same sensation in
your listening room by shifting the sound of
the front speakers “into” the screen.
• Cinema Studio Reverberation
Reproduces the reverberations peculiar to a
movie theatre.
46US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Cinema Studio EX is the integrated mode which
operates these elements simultaneously.
• This function is unavailable when playing Super
Audio CDs.
Notes
• When you play a Super Audio CD (Direct Stream
Digital), the sound field changes to “AUTO
FORMAT DIRECT AUTO” automatically.
• For PCM96 kHz sources, 2CH, A.F.D. and MODE is
not available.
• The virtual speaker effect may cause increased noise
in the playback signal.
• When listening with sound fields that employ virtual
speakers, you will not be able to hear any sound
coming directly from the surround speakers.
Tips
FOR MUSIC
• When you want to output the TV sound or stereo
sound of a 2 channel source from the 7 speakers,
select any sound field other than “AUTO FORMAT
DIRECT AUTO” or “2CH STEREO.”
• Whenever you select a function such as DVD or
TUNER, the sound field that was last applied to that
function is automatically applied again. For example,
if you listen to DVD with HALL as the sound field,
then change to another function, and then return to
DVD, HALL will be applied again. With the tuner,
sound fields are memorized separately for all preset
stations.
Sound field
HALL
Display
HALL
JAZZ CLUB
LIVE CONCERT
JAZZ CLUB
L.CONCERT
x HALL
Reproduces the acoustics of a rectangular
concert hall.
x JAZZ CLUB
Reproduces the acoustics of a jazz club.
• You can identify the encoding format of program
software by looking at its packaging.
x L. CONCERT (Live Concert)
Reproduces the acoustics of a 300-seat live
concert.
– Dolby Digital discs are labelled with the
logo.
– DTS-ES or DTS 96/24 encoded programs are
marked with DTS-ES or DTS 96/24.
When using headphones
– Dolby Surround encoded programs are labelled
with the
logo.
Sound field
Display
– DTS Digital Surround discs are marked with DTS.
HEADPHONE THEATER
HEADPHONE 2CH
HP.THEATER
HP.[2CH]
x HP. THEATER (HEADPHONE THEATER)
This mode is very effective with 5.1 ch discrete
signal sources like Dolby Digital and DTS.
x HP.[2CH] (HEADPHONE 2CH)
This mode outputs the sound from the
headphone L/R. Standard 2 channel (stereo)
sources completely bypass the sound field
processing. Multi channel surround formats are
downmixed to two channels.
To turn the surround effect off
Press A.F.D. on the remote repeatedly until
“A.F.D AUTO” appears in the front panel
display, or press 2CH on the remote to display
“2CH STEREO.”
47US
Download from Www.Somanuals.com. All Manuals Search And Download.
Input stream Output Applied surround back
channel decoder
Selecting the Surround
Back Decoding Mode
Dolby Digital 5.1
5.1
—
DTS 5.1
5.1
—
Dolby Digital 6.1
EX
Matrix decoder conforms
to Dolby Digital EX
b)
This function lets you select the decoding mode
for the surround back signals of the multi
channel input stream.
DTS-ESMatrix 6.1
6.1
DTS Matrix decoder
c)
By decoding the surround back signal of DVD
software, etc., recorded in Dolby Digital EX,
DTS-ES Matrix, DTS-ES Discrete 6.1 format,
etc., you can enjoy the kind of surround sound
DTS-ES
Discrete 6.1
6.1
DTS Discrete decoder
d)
When selecting “SB MATRIX”
Dolby Digital EX is applied to decode the
surround back signal regardless of the 6.1
a)
channel decode flag in the input stream. This
decoder conforms to Dolby Digital EX, and
e)
functions the same as the decoders used in
movie theatres.
Input stream Output Applied surround back
channel decoder
ENTER
X/x
Dolby Digital 6.1
5.1
Matrix decoder conforms
to Dolby Digital EX
DTS 5.1
6.1
Matrix decoder conforms
to Dolby Digital EX
AMP MENU
Dolby Digital 6.1
EX
Matrix decoder conforms
to Dolby Digital EX
b)
DTS-ESMatrix 6.1
6.1
Matrix decoder conforms
to Dolby Digital EX
c)
1
Press AMP MENU.
DTS-ES
Discrete 6.1
6.1
Matrix decoder conforms
to Dolby Digital EX
d)
Set the function of the remote to DVD, and
then press AMP MENU.
When selecting “SB OFF”
Surround back decoding is not performed.
2
3
Press X/x repeatedly until “SurrB
DEC.” appears in the front panel
display, then press ENTER.
a) 6.1 channel decode flag is information recorded in
software like DVD.
Press X/x to select the surround back
mode you want according to the input
stream, then press ENTER or AMP
MENU.
b) Dolby Digital DVD that includes a Surround EX
flag. Check the Dolby Corporation web page help
for information about Surround EX films.
c) Software encoded with a flag to denote it has both
Surround EX and 5.1 channel signals.
The default setting is “SB AUTO.”
When selecting “SB AUTO”
d) Software encoded with both 5.1 channel signals and
an extension stream designed for returning those
signals to 6.1 discrete channels. Discrete 6.1
channel signals are DVD specific signals, not used
in movie theatres.
When you input stream contains the 6.1 channel
a)
decoding flag , the appropriate decoder is
applied to decode the surround back signal.
e) This decoder can be used for all 6.1 formats (Dolby
Digital EX, DTS-ES Matrix 6.1, and DTS-ES
Discrete 6.1).
48US
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• You can select the surround back decoding only when
fields, this function is bypassed internally.
• Some discs have no Dolby Digital EX flag, even
though their packaging may contain a Dolby Digital
Surround EX logo. In this case, select “SB
MATRIX.”
Selecting the Decode
Priority
This function lets you select the decode priority
when digital signals are input from the DIGITAL
IN (OPTICAL IN/COAXIAL IN) jack, or digital
signals are processed in DVD mode.
ENTER
X/x
AMP MENU
1
Press AMP MENU.
Set the function of the remote to DVD, and
then press AMP MENU.
2
3
Press X/x repeatedly until “DEC. PRI.”
appears in the front panel display, then
press ENTER.
Press X/x to select the decode priority
you want, then press ENTER or AMP
MENU.
The default setting is “PCM.”
When selecting “PCM”
PCM signals are given priority (to prevent the
interruption when playback starts). Even when
other signals are input, the sound will be output.
However, when DTS-CD signals are output, no
sound or noise will be heard. In this case, select
“AUTO.”
When selecting “AUTO”
The most suitable decode method is
automatically selected from DTS, Dolby Digital,
or PCM. However, when PCM signal playback
starts, sound will not be output initially.
Tip
As long as DVD mode is selected, you can play DTS-
CD even if “PCM” is selected.
49US
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker impedance
Changing the Speaker
Impedance Value
To enjoy the best possible multi channel
surround, connect speakers with a nominal
impedance of 8 ohms or higher to the FRONT,
CENTER, SURROUND and SURROUND
BACK terminals, and set the value to “SP 8Ω.”
Refer to the operating instructions supplied with
your speakers if you are not sure of their
impedance. (This information is often on the
back of the speaker.) Alternatively, you may
connect speakers of nominal impedance
between 4 and 8 ohms to any or all of the speaker
terminals. In this case, be sure to set the value to
“SP 4Ω/6Ω” even if you connect just one
speaker of nominal impedance between 4 and 8
ohms.
You can change the impedance value in
accordance with your speaker’s impedance.
The default settings are underlined.
ENTER
X/x
AMP MENU
1
Press AMP MENU.
Set the function of the remote to DVD, and
then press AMP MENU.
2
3
Press X/x repeatedly until “SP. IMP.
(Ω)” appears in the front panel display,
then press ENTER.
Press X/x to select “SP 4Ω/6Ω” or “SP
8Ω” in accordance with impedance,
then press ENTER or AMP MENU.
SP 8Ω
Select this if the speaker
impedance value is 8 ohms or
higher.
SP 4Ω/6Ω
Select this if the speaker
impedance value is under 8
ohms.
Notes
• Use high performance speakers.
• Use suitably sized speakers of similar performance
for the front, center, surround, and surround back
speakers.
50US
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press ENTER.
The angle number changes to “-.”
Using Various Additional Functions
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
Changing the Angles
(
)
1 8 3 4
T
–
1 : 3 2 : 5 5
(
)
9
If various angles (multi-angles) for a scene are
recorded on a DVD, you can change the viewing
angle.
For example, while playing a scene of a train in
motion, you can display the view from either the
front of the train, the left window of the train, or
from the right window without having the train’s
movement interrupted.
Select the angle number using the
number buttons or X/x, then press
ENTER.
The angle is changed to the selected angle.
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
Note
Depending on the DVD, you may not be able to change
the angles, even if multi-angles are recorded on the
DVD.
Number
ANGLE
Buttons
Tip
You can select the angle directly by pressing ANGLE.
Each time you press the button, the angle changes.
ENTER
X/x
DVD
DISPLAY
1
2
Press DVD DISPLAY during playback.
The Control Menu appears.
Press X/x to select
(ANGLE).
The angle number appears.
The number in parentheses indicates the
total number of angles. The “ANGLE”
indicator lights up in green when angles are
recorded on the disc.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
T
1
1 : 3 2 : 5 5
(
)
9
51US
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Press X/x to select the language.
Displaying Subtitles
Depending on the DVD, the choice of
language varies.
When 4 digits are displayed, they indicate
the language code. Refer to the language
the code represents.
If subtitles are recorded on a disc, you can turn
the subtitles on or off while playing. If
multilingual subtitles are recorded on the disc,
you can change the subtitle language while
playing, or turn the subtitles on or off whenever
you want. You can select the language you want
to practice, for example, turn on the subtitles for
better understanding.
Press ENTER.
To cancel the SUBTITLE setting
Select “OFF” in Step 3.
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
Note
Depending on the DVD, you may not be able to change
the subtitles, even if multilingual subtitles are recorded
on it.
SUBTITLE
Tip
You can select SUBTITLE directly by pressing
SUBTITLE. Each time you press the button, the item
changes.
ENTER
X/x
DVD
DISPLAY
1
2
Press DVD DISPLAY during playback.
The Control Menu appears.
Press X/x to select
(SUBTITLE), then press ENTER.
The options for SUBTITLE appear.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
T
1 : 3 2 : 5 5
OFF
1: ENGLISH
2: FRENCH
3: SPANISH
52US
Download from Www.Somanuals.com. All Manuals Search And Download.
• CINEMA 2: Bright colors become brighter
and dark colors become richer, and color
contrast is increased.
Adjusting the Playback
Picture
3
Select the PICTURE MODE you want
using X/x, then press ENTER.
(PICTURE MODE)
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
You can adjust the video signal of the DVD,
VIDEO CD or JPEG from the receiver to obtain
the picture quality you want. Choose the setting
that best suits the program you are watching.
Tip
When you watch a movie, “CINEMA 1” or “CINEMA
2” is recommended.
Note
The setting you select in PICTURE MODE is reflected
in all screen displays.
ENTER
X/x
DVD
DISPLAY
1
2
In stop mode, press DVD DISPLAY.
The Control Menu appears.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
T
STANDARD
DYNAMIC 1
DYNAMIC 2
CINEMA 1
CINEMA 2
Press X/x to select
MODE), then press ENTER.
(PICTURE
The options for PICTURE MODE appear.
• STANDARD: Displays a standard picture.
• DYNAMIC 1: Produces a bold dynamic
picture by increasing the picture contrast
and the color intensity.
• DYNAMIC 2: Produces a more dynamic
picture than DYNAMIC 1 by further
increasing the picture contrast and the color
intensity.
• CINEMA 1: Enhances detail in dark areas
by increasing the black level.
53US
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press X/x to select
PARENTAL CONTROL), then press
ENTER.
(CUSTOM
Locking Discs
(CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL)
“CUSTOM PARENTAL CONTROL” is
selected.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
T
1 : 3 2 : 5 5
You can set two kinds of playback restrictions
for a disc.
• Custom Parental Control
You can set the playback restrictions so that
the receiver will not play inappropriate discs.
• Parental Control
Playback of some DVDs can be limited
according to a predetermined level, such as the
age of the viewer.
ON
PASSWORD
4
Press X/x to select “ON t,” then press
ENTER.
x If you have not entered a password
The same password is used for both Parental
Control and Custom Parental Control.
yet
The display for registering a new password
appears.
Custom Parental Control
CUSTOM PARENTAL CONTROL
Enter a new 4-digit password,
You can set the same Custom Parental Control
password for up to 25 discs. If you set a 26th
disc, the playback restriction of the disc for
which you first set the password is cancelled.
then press ENTER
.
Enter a 4-digit password by using the
number buttons, then press ENTER.
The display for confirming the password
appears.
Number
buttons
x If you have already registered a
password
The display for entering the password
appears.
x
ENTER
C/X/x/c
CUSTOM PARENTAL CONTROL
ENTER
Enter password, then press
.
DVD
O RETURN/
DISPLAY
EXIT
1
2
Insert the disc you want to lock.
If the disc is playing, press x to stop
playback.
In stop mode, press DVD DISPLAY.
The Control Menu appears.
54US
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Enter your 4-digit password by using
the number buttons, then press
ENTER.
Playing the disc for which
Custom Parental Control is
set
“Custom parental control is set.” appears
and the screen returns to the Control Menu
display.
1
Insert the disc for which Custom
Parental Control is set.
If you make a mistake entering your
password
Press C before you press ENTER and input
the correct number.
The CUSTOM PARENTAL CONTROL
display appears.
CUSTOM PARENTAL CONTROL
If you make a mistake
Press O RETURN/EXIT, then start from Step
3 again.
Custom parental control is already
set. To play, enter your password
ENTER
and press
.
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
2
Enter your 4-digit password using the
number buttons, then press ENTER.
To turn off the Custom Parental
Control function
The receiver is ready for playback.
Notes
1 In Step 4, select “OFF t,” then press
ENTER.
• When you change the layer or area in a Super Audio
CD which has Custom Parental Control set, the
display for entering the password may appear.
• When you set the Custom Parental Control password
for a Hybrid Super Audio CD, the Custom Parental
Control setting only works for the current layer.
2 Enter your 4-digit password using the
number buttons, then press ENTER.
To change the password
1 In Step 4, press X/x to select “PASSWORD
t,” then press ENTER.
The display for entering the password
Tip
If you forget your password, enter the 6-digit number
“199703” using the number buttons when the
CUSTOM PARENTAL CONTROL display asks you
for your password, then press ENTER. The display
will ask you to enter a new 4-digit password.
appears.
2 Enter your 4-digit password using the
number buttons, then press ENTER.
3 Enter a new 4-digit password using the
number buttons, then press ENTER.
4 To confirm your password, re-enter it using
the number buttons, then press ENTER.
continued
55US
Download from Www.Somanuals.com. All Manuals Search And Download.
x If you have not entered a password
The display for registering a new password
appears.
Limiting playback for children
(Parental Control)
(DVD only)
Playback of some DVDs can be limited
according to a predetermined level, such as the
age of the viewer. The “Parental Control”
function allows you to set a playback limitation
level.
CUSTOM SETUP
PARENTAL CONTROL
Enter a new 4-digit password,
ENTER
then press
.
A scene that is limited is not played, or it is
replaced by a different scene.
Enter a 4-digit password using the number
buttons, then press ENTER.
The display for confirming the password
appears.
x When you have already registered a
password
The display for entering the password
appears.
Number
buttons
H
CUSTOM SETUP
PARENTAL CONTROL
ENTER
Enter password, then press
.
ENTER
C/X/x/c
O RETURN/
EXIT
DVD
SETUP
4
Enter your password using the number
buttons, then press ENTER.
The display for setting the playback
limitation level and changing the password
appears.
1
2
In stop mode, press DVD SETUP.
The Setup Display appears.
Press X/x to select “CUSTOM SETUP,”
then press ENTER.
CUSTOM SETUP
PARENTAL CONTROL
“CUSTOM SETUP” is displayed.
LEVEL:
OFF
USA
STANDARD:
CHANGE PASSWORD
CUSTOM SETUP
PARENTAL CONTROL
TRACK SELECTION
AUDIO DRC:
OFF
OFF
DATA CD PRIORITY:
JPEG DATE:
MP3
MM/DD/YYYY
3
Press X/x to select “PARENTAL
CONTROL t,” then press ENTER.
56US
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press X/x to select “STANDARD,” then
press ENTER.
If you make a mistake
Press O RETURN/EXIT to go back to the
previous screen.
The selection items for “STANDARD” are
displayed.
To turn off the Setup Display
Press DVD SETUP repeatedly until the Setup
Display is turned off.
CUSTOM SETUP
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
USA
OTHERS
To turn off the Parental Control
function and play the DVD after
entering your password
CHANGE PASSWORD
Set “LEVEL” to “OFF” in Step 8.
6
7
Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
To change the password
1 In Step 5, select “CHANGE PASSWORD
t” using x, then press ENTER.
The display for entering the password
appears.
The area is selected.
If you select “OTHERS t,” select and
enter the standard code in the table on
page 58 using the number buttons.
2 Follow Step 3 to enter a new password.
Press X/x to select “LEVEL,” then
press ENTER.
The selection items for “LEVEL” are
displayed.
CUSTOM SETUP
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
8:
CHANGE PASSWORD 7:
NC17
R
6:
5:
4:
3:
2:
1:
PG13
PG
G
8
Select the level you want using X/x,
then press ENTER.
The Parental Control setting is complete.
CUSTOM SETUP
PARENTAL CONTROL
LEVEL:
STANDARD:
4:
PG13
USA
CHANGE PASSWORD
The lower the value, the more strict the
limitation.
continued
57US
Download from Www.Somanuals.com. All Manuals Search And Download.
Area Code
Playing the disc for which
Parental Control is set
Standard
Argentina
Australia
Austria
Code number
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2219
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2543
2528
2184
1
Insert the disc and press H.
The PARENTAL CONTROL display
appears.
Belgium
Brazil
2
Enter your 4-digit password using the
number buttons, then press ENTER.
Canada
The receiver starts playback.
Chile
China
Notes
• If you play a DVD which does not have the Parental
Control function, playback cannot be limited on this
receiver.
Denmark
Finland
France
• Depending on the DVD, you may be asked to change
the parental control level while playing the disc. In
this case, enter your password, then change the level.
If the Resume Play mode is cancelled, the level
returns to the original level.
Germany
Hong Kong
India
Indonesia
Italy
Tip
If you forget your password, remove the disc and
repeat Step 1 to 3 of “Limiting playback for children.”
When you are asked to enter your password, enter
“199703” using the number buttons, then press
ENTER. The display will ask you to enter a new 4-digit
password. After you enter a new 4-digit password in
Step 3, replace the disc in the receiver and press H.
When the PARENTAL CONTROL display appears,
enter your new password.
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Spain
Sweden
Switzerland
Taiwan
Thailand
United Kingdom
58US
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press ENTER.
When registration is completed, the RM
SET UP indicator flashes twice.
If registration is incomplete, the RM SET
UP indicator rapidly flashes 4 times.
Other Operations
Controlling Other Units
with the Supplied Remote
* Use the number buttons only to enter the code
number of controllable TVs.
Code numbers of controllable
TVs
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your TV.
By adjusting the remote signal, you can control
your TV, satellite receiver or VCR with the
supplied remote.
Notes
• If you enter a new code number, the code number
previously entered will be erased.
Manufacturer
SONY
Code number
501,502
• When you replace the batteries of the remote, the
code number may reset itself to the default (SONY)
setting. Reset the appropriate code number.
AIWA
501,502
DAEWOO
FISHER
504,505,506,507,515,544
508
Tip
You can set the code number for your TV or satellite
receiver separately.
GOLDSTAR
GRUNDIG
HITACHI
ITT/NOKIA
JVC
503,511,512,515,534,544
517,534
Controlling TVs with the
remote
513,514,515,544
521,522
516
MAGNAVOX
503,518,544
TV ?/1
AV ?/1
MITSUBISHI/MGA 503,519,544
RM SET UP
NEC
503,520,544
PANASONIC
PHILIPS
509,524
515,518
PIONEER
RCA/PROSCAN
SAMSUNG
SANYO
509,525,526,540
510,527,528,529,544
503,515,531,532,533,534,544
508,545,546,547
535
Number*
buttons
ENTER
SHARP
TELEFUNKEN
THOMSON
TOSHIBA
ZENITH
523,536,537,538
530,537,539
TV CH +/–
TV/VIDEO
535,540,541
TV VOL +/–
542,543
Controlling the TV
You can control your TV using the buttons
below.
1
Press RM SET UP and AV [/1
simultaneously.
The RM SET UP indicator lights up.
2
3
Press TV [/1.
By pressing
TV [/1
You can
The RM SET UP indicator flashes once.
Turn the TV on or off.
TV/VIDEO
Switch the TV’s input source
between the TV and other input
sources.
Enter your TV manufacturer code (see
the table) using the number buttons.
continued
59US
Download from Www.Somanuals.com. All Manuals Search And Download.
Code numbers of controllable
satellite receivers
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your satellite receiver.
By pressing
TV VOL +/–
TV CH +/–
You can
adjust the TV volume.
change the TV channel.
Note
Depending on the TV, you may not be able to control
your TV or to use some of the buttons above.
Manufacturer
SONY
Code number
801,802,803,804
JERROLD/G.I.
806,807,808,809,810,811,
812,813,814
Controlling satellite receivers
with the remote
PANASONIC
RCA
818
805,819
815,816,817
AV ?/1
RM SET UP
S.ATLANTA
TV/SAT
Controlling the satellite receiver
Press TV/SAT.
Sources that can be controlled by the remote
change depending on the setting of TV/SAT.
You can control your satellite receiver using the
buttons below.
Number
buttons
ENTER
By pressing
You can
AV [/1
Turn the satellite receiver on or
off.
JUMP
Jump
Number buttons
ENTER
Select a channel.
Confirm the selected channel.
Change the audio.
Change channels.
Display the program guide.
AUDIO
1
Press RM SET UP and AV [/1
simultaneously.
CH +/–
TOP MENU/
GUIDE
The RM SET UP indicator lights up.
AV MENU
Display the menu.
2
3
Press TV/SAT.
DVD DISPLAY
Turn the display on or off.
Enter your Satellite receiver’s
manufacturer code (see the table)
using the number buttons.
O RETURN/EXIT Return to the previous display
in the program guide or menu.
C/X/x/c/ ENTER Select the item in the program
4
Press ENTER.
guide or menu.
When registration is completed, the RM
SET UP indicator flashes twice.
Notes
• Depending on the satellite receiver, you may not be
able to control your satellite receiver or to use some
of the buttons above.
• To operate a DVD player, press DVD, and then
change the mode of the receiver to DVD.
60US
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer
GRUNDIG
HITACHI
Code number
724
Controlling the VCR with the
remote
722,725,729,741
717
ITT/NOKIA
JVC
AV ?/1
RM SET UP
726,727,728,736
730,731,738
MAGNAVOX
VIDEO2
VIDEO1
MITSUBISHI/MGA 732,733,734,735
NEC
736‘
PANASONIC
PHILIPS
729,730,737,738,739,740
729,730,731
729
Number
buttons
PIONEER
RCA/PROSCAN
SAMSUNG
SANYO
ENTER
722,729,730,731,741,747
742,743,744,745
717,720,746
748,749
SHARP
TELEFUNKEN
TOSHIBA
ZENITH
751,752
747,755,756
754
1
Press RM SET UP and AV [/1
simultaneously.
Controlling the VCR
The RM SET UP indicator lights up.
Press the button “VIDEO1,” or “VIDEO2.”
Sources that can be controlled by the remote
change depending on the setting of VIDEO1 or
VIDEO2.
You can control your VCR using the buttons
below.
2
3
Press VIDEO1 or VIDEO2.
Enter your VCR’s manufacturer code
(see the table) using the number
buttons.
4
Press ENTER.
By pressing
AV [/1
You can
When the registration is completed, the RM
SET UP indicator flashes twice.
Turn the VCR on or off.
Select a channel.
Confirm the selected channel.
Change the audio.
Change VCR channels.
Fast Forward or fast Reverse.
Play.
Number buttons
ENTER
Code numbers of controllable
VCR
AUDIO
CH –/+
Press VIDEO1 or VIDEO2.
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your VCR.
m/M
H
X
Pause.
x
Stop.
Manufacturer
SONY
Code number
AV MENU
DVD DISPLAY
Display the menu.
The display is on or off.
701,702,703,704,705,706
710,750,757,758
707,708,709,759
740
AIWA
C/X/x/c/ ENTER Select the item in the program
AKAI
guide or menu.
BLAUPUNKT
EMERSON
FISHER
711,712,713,714,715,716,750
717,718,719,720
721,722,730
Notes
• Depending on the VCR, you may not be able to
control your VCR, or use some of the buttons above.
• To operate a DVD player, press DVD, and then
change the mode of the receiver to DVD.
GENERAL
ELECTRIC
GOLDSTAR
723,753
61US
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Units
Enjoying the Radio
You can use VCRs or other units connected to
the VIDEO1, TV/SAT, or VIDEO2 jacks. Refer
to the operation manual supplied with the other
unit for further information on its operation.
Presetting Radio Stations
You can preset 20 stations for FM and 10
stations for AM. Before tuning, make sure to
turn down the volume to minimum.
TV/SAT
"/1
VIDEO2
VIDEO1
BAND
TUNING
–/+
PRESET
–/+
ENTER X/x
AMP MENU
Press the button “VIDEO1,” “VIDEO2,” or
“TV/SAT” you want to use.
1
2
Press BAND repeatedly until the band
you want appears in the front panel
display.
When you press the button you want to use, the
mode of the receiver changes and the currently
selected unit name appears in the front panel
display.
Each time you press BAND, the band
toggles between AM and FM.
Tip
The BAND button is available only the
DVD function is selected on the remote.
You can also select the mode using FUNCTION –/+ on
the receiver. Each time you press FUNCTION –/+, the
mode of the receiver changes in the following
sequence.
Press and hold TUNING + or –, then
release.
DVD t VIDEO1 t VIDEO2 t TV/SAT t
TUNER t DVD…
Scanning stops when the receiver tunes in a
station. “TUNED” and “ST” (for stereo
program) appear in the front panel display.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
3
4
Press AMP MENU.
Press X or x repeatedly until
“MEMORY” appears in the front panel
display.
62US
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press ENTER.
Listening to the Radio
A preset number appears in the front panel
display. The preset number blinks on and
off.
Preset radio stations in the receiver’s memory
page 62).
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
"/1
6
7
Press PRESET + or – to select the
preset number you want.
BAND
DISPLAY
/JUMP
FM MODE
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
PRO LOGIC
SHUFFLE
dB PCM DSD NEO:6
REPEAT1 FM AM
PROGRAM MEMORY
kHz DTS-ES 96/24
MHz MPEG-2 AAC
Press ENTER.
The station is stored.
PRESET
–/+
TUNING
–/+
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
VOLUME
+/–
m
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
1
Press BAND repeatedly until FM or AM
appears in the front panel display.
8
Repeat 1 to 7 to store other stations.
The last received station is tuned in.
The Band button is available only the DVD
function is selected on the remote.
To change the preset number
Restart from step 1.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
To change the AM tuning interval
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
The AM tuning interval can be set to either
9 kHz or 10 kHz (default).
m
To change the AM tuning interval, turn off the
receiver by pressing "/1 on the remote. While
holding down x (on the receiver), press "/1 on
the remote to turn on the power. If you change
the interval, the AM preset stations will be
erased.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
2
3
Press PRESET + or – repeatedly to
select the preset station you want.
To reset the interval, repeat the same procedure.
Each time you press the button, the receiver
tunes in one preset station.
Every time you press BAND, the band
toggles between AM or FM.
Adjust the volume by pressing
VOLUME +/–.
To turn off the radio
Press "/1 on the remote or POWER on the
receiver.
continued
63US
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Press BAND repeatedly until FM or AM
appears in the front panel display.
To listen to non-preset radio
stations
Use manual or automatic tuning in Step 2.
For manual tuning, press TUNING + or – on the
remote repeatedly.
The last station you received is tuned in.
Each time you press BAND, the band
toggles between AM or FM.
The Band button is available only the DVD
function is selected on the remote.
For automatic tuning, press and hold TUNING +
or – on the remote.
Press PRESET + or – repeatedly to
select the preset station you want to
create an index name for.
Tips
• If an FM program is noisy, press FM MODE on the
remote so that “MONO” appears in the front panel
display. There will be no stereo effect, but the
reception will improve. Press the button again to
restore the stereo effect.
3
4
Press AMP MENU.
Press X or x repeatedly until “NAME
INPUT” appears.
• To improve reception, reorient the supplied antennas.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
To check the frequency
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Press DISPLAY/JUMP repeatedly.
Each time you press DISPLAY/JUMP, the front
panel display changes as follows:
index name of the station* t frequency t
index name of the station...
5
6
Press ENTER.
Create an index name by using the
cursor buttons:
* This is displayed if you have entered a name
for a preset station, see “Naming Preset
Press X/x to select a character, then press c
to move the cursor to the next position.
If you make a mistake
Press C or c repeatedly until the character
to be changed flashes, then press X/x to
select the desired character.
Naming Preset Stations
You can enter a name of up to 8 characters for
preset stations. These names (for example,
“XYZ”) appear in the receiver’s front panel
display when a station is selected.
Note that no more than one name can be entered
for each preset station.
7
Press ENTER.
The station name is stored.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Note
You cannot input the name during manual tuning.
(“Not in Use” appears in the front panel display.)
BAND
PRESET
–/+
ENTER
C/X/x/c
AMP MENU
64US
Download from Www.Somanuals.com. All Manuals Search And Download.
x DISP OFF
Turns off the front panel display and the MULTI
CHANNEL DECODING indicator. When the
receiver accepts an incoming remote signal, it
lights for 5 seconds at DIMMER 2 brightness.
Changing the Brightness
of the Front Panel
There are four levels of brightness for the front
panel display.
Adjust the brightness according to your room’s
lighting conditions.
Each time you change the setting, the brightness
of the front panel display changes as follows:
DIMMER OFF t DIMMER 1 t DIMMER 2
t DISP OFF t DIMMER OFF...
The default setting is “DIMMER OFF.”
ENTER
X/x
AMP MENU
1
Press AMP MENU.
Set the function of the remote to DVD, and
then press AMP MENU.
2
3
Press X/x repeatedly until “DIMMER”
appears in the front panel display, then
press ENTER.
Press X/x to change the brightness,
then press ENTER or AMP MENU.
x DIMMER OFF
The front panel display and the MULTI
CHANNEL DECODING indicator are brightly
lit.
x DIMMER 1
The front panel display and the MULTI
CHANNEL DECODING indicator are half lit.
x DIMMER 2
The front panel display and the MULTI
CHANNEL DECODING indicator are dimly lit.
65US
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press X/x to select the setup item from
the displayed list: “LANGUAGE
Settings and Adjustments
SETUP,” “SCREEN SETUP,” “CUSTOM
SETUP,” “SPEAKER SETUP,” and
“RESET .” Then press ENTER or c.
*
Using the Setup Display
The selected Setup item appears.
Example: “SCREEN SETUP”
By using the Setup Display, you can make
various adjustments to items, such as picture and
sound. You can also set the subtitle language
and the Setup Display, among other things. For
73. For an overall list of Setup Display items,
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
COMPONENT OUT:
4:3 LETTER BOX
ON
JACKET PICTURE
INTERLACE
3
Select an item using X/x, then press
ENTER or c.
How to use the Setup Display
The options for the selected item appear.
Example: “TV TYPE”
SCREEN SETUP
TV TYPE:
4:3 LETTER BOX
SCREEN SAVER:
BACKGROUND:
COMPONENTOUT:
4:3 PAN SCAN
16:9
ENTER
C/X/x/c
O RETURN/
EXIT
DVD
Options
SETUP
Press C or O RETURN/EXIT to return to
setup items.
4
Select a setting using X/x, then press
ENTER.
1
In stop mode, press DVD SETUP.
The setting is selected and setup is
complete.
The Setup Display appears.
Example: “4:3 PAN SCAN”
LANGUAGE SETUP
OSD :
ENGLISH
Main
item
DVD MENU :
ENGLISH
ENGLISH
ENGLISH
Selected setting
AUDIO :
SUBTITLE :
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
COMPONENT OUT:
4:3 PAN SCAN
ON
JACKET PICTURE
INTERLACE
66US
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the Setup Display
Press DVD SETUP repeatedly until the Setup
Display is turned off.
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
* When you select “RESET”
in step 2, the
following items are returned to the default settings.
• Setup Menu (except for the PARENTAL
After you select “RESET” and press ENTER, select
“YES” to reset the settings (it takes a few seconds to
complete). Select “NO” and press ENTER to cancel.
Do not press POWER on the receiver, when resetting
the receiver.
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
Select “LANGUAGE SETUP” in the Setup
Display. For details on using the display, see
LANGUAGE SETUP
OSD :
DVD MENU :
AUDIO :
SUBTITLE :
ENGLISH
ENGLISH
ENGLISH
ENGLISH
x OSD (On-Screen Display)
Selects the display language on the screen.
Selects the language from the displayed list.
x DVD MENU (DVD only)
Selects the desired language for the DVD menu.
x AUDIO (DVD only)
Selects the language of the sound track.
Selects the language from the displayed list.
x SUBTITLE (DVD only)
Selects the language of the subtitle.
Selects the language from the displayed list.
Note
If you select a language that is not recorded on the
DVD, one of the recorded languages will be
automatically selected (except for “OSD”).
Tip
If you select “OTHERS t” in “DVD MENU,”
“SUBTITLE,” or “AUDIO,” select and enter the
language code from the list using the number buttons
After you have made a selection, the language code
(4 digits) is displayed the next time you select
“OTHERS t.”
67US
Download from Www.Somanuals.com. All Manuals Search And Download.
4:3 LETTER BOX
Settings for the Display
(SCREEN SETUP)
4:3 PAN SCAN
Choose settings according to the TV to be
connected.
Select “SCREEN SETUP” in the Setup Display.
For details on using the display, see “Using the
16:9
The default settings are underlined.
Note
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
COMPONENT OUT:
4:3 LETTER BOX
ON
JACKET PICTURE
INTERLACE
Depending on the DVD, “4:3 LETTER BOX” may be
selected automatically instead of “4:3 PAN SCAN” or
vice versa.
x SCREEN SAVER
Turns the screen saver on and off so that the
screen saver image appears when you leave the
receiver in pause or stop mode for 15 minutes, or
when you playback a CD, a Super Audio CD, an
MP3 or a JPEG file (except during the slide
show) for more than 15 minutes. The screen
saver will help prevent your display device from
becoming damaged (afterimage). Press H to
turn off the screen saver.
x TV TYPE (DVD only)
Selects the aspect ratio of the connected TV (4:3
standard or wide).
4:3
LETTER
BOX
Select this if you connect a 4:3
screen TV. Displays a wide picture
with bands on the upper and lower
portions of the screen.
4:3
PAN SCAN
Select this if you connect a 4:3
screen TV. Automatically displays
the wide picture on the entire
screen and cuts off the portions
that do not fit.
ON
Turns on the screen saver.
Turns off the screen saver.
OFF
x BACKGROUND
Selects the background color or picture on the
TV screen in stop mode or while playing a CD.
16:9
Select this if you connect a wide-
screen TV or a TV with a wide
mode function.
JACKET
PICTURE
The jacket picture (still picture)
appears in the background, but
only if a jacket picture is already
recorded on the disc (CD-
EXTRA, etc.). If the disc does not
contain a jacket picture, the
“GRAPHICS” picture appears.
GRAPHICS
A preset picture stored in the
receiver appears in the
background.
BLUE
The background color is blue.
The background color is black.
BLACK
68US
Download from Www.Somanuals.com. All Manuals Search And Download.
x COMPONENT OUT
This will change the type of signal output from
the COMPONENT VIDEO OUT jacks on the
about the different types.
Custom Settings
(CUSTOM SETUP)
INTERLACE
Select this when you are
connected to a standard (interlace
format) TV.
Allows setting up Parental Control and other
settings.
PROGRESSIVE
Select this when you have a TV
that can accept progressive
signals.
Select “CUSTOM SETUP” in the Setup
Display. For details on using the display, see
The default settings are underlined.
Note
If you set “COMPONENT OUT” in “SCREEN
SETUP” to “PROGRESSIVE” even though your TV
cannot accept the signal in progressive format, press
and hold x and . simultaneously for a few
seconds. The “COMPONENT OUT” setting returns to
“INTERLACE.”
CUSTOM SETUP
PARENTAL CONTROL
TRACK SELECTION
AUDIO DRC:
DATA CD PRIORITY:
JPEG DATE:
OFF
OFF
MP3
MM/DD/YYYY
x PARENTAL CONTROL t (DVD only)
Sets a password and playback limitation level
for DVDs with playback limitation for children.
For details, see “Limiting playback for children
x TRACK SELECTION (DVD only)
Gives the sound track having the highest number
of channels priority when you play a DVD on
which multiple audio formats (PCM, MPEG
audio, DTS, or Dolby Digital format) are
recorded.
OFF
No priority given.
Priority given.
AUTO
Notes
• When you set the item to “AUTO,” the language may
change. The “TRACK SELECTION” setting has
higher priority than the “AUDIO” settings in
• If PCM, DTS, MPEG audio, and Dolby Digital sound
tracks have the same number of channels, the receiver
selects PCM, DTS, Dolby Digital, and MPEG audio
sound tracks in this order.
• Depending on the DVD, the audio channel with
priority may be predetermined. In this case, you
cannot give priority to the DTS, Dolby Digital, or
MPEG audio format by selecting “AUTO.”
continued
69US
Download from Www.Somanuals.com. All Manuals Search And Download.
x AUDIO DRC (AUDIO DYNAMIC RANGE
COMPRESSION)
Narrows the DYNAMIC range of the
sound track.
Settings for the Speakers
(SPEAKER SETUP)
Useful for watching movies at low volume late
at night.
To obtain the best possible surround sound, set
for the size of the speakers you have connected
and their distance from your listening position.
Then use the test tone to adjust the level and the
balance of the speakers to the same level.
OFF
No compression of DYNAMIC
range.
STANDARD
Reproduces the sound track with the
kind of DYNAMIC range that the
recording engineer intended.
Select “SPEAKER SETUP” in the setup
display. For details, see “Using the Setup
MAX
Narrows the DYNAMIC range
fully.
The default settings are underlined.
Note
DYNAMIC range compression only applies to Dolby
Digital sources.
SPEAKER SETUP
SIZE:
DISTANCE:
x DATA CD PRIORITY (MP3, JPEG only)
Set priority data you want to play, when you
play a DATA CD (CD-ROM/CD-R/CD-RW)
containing MP3 audio tracks and JPEG image
files.
LEVEL:
BALANCE:
TEST TONE:
To return to the default setting
when changing a setting
Select the item, then press CLEAR.
Only the selected item is returned to the default
setting.
MP3
If an MP3 file exists on a disc, the
receiver recognises the disc as an
“MP3 Disc.” If only JPEG files exist
on the disc, the receiver recognises
the disc as a “JPEG Disc.”
x SIZE
JPEG
If a JPEG file exists on the disc, the
receiver recognises the disc as a
“JPEG Disc.” If only MP3 files exist
on the disc, the receiver recognises
the disc as an “MP3 Disc.”
If you use small speakers, do not connect a
center, surround speakers, or surround back
speaker, or move the surround speakers, set the
parameters for FRONT, CENTER,
SURROUND, SURROUND BACK, and
SUBWOOFER.
Notes
• When you play multi-session CDs, the receiver
decides a target to play for the last session or session
linked with the last session.
FRONT
LARGE: Normally select this.
SMALL: Select this if small
speakers are used for the front
speaker.
• If you change this setting, reinsert the disc.
x JPEG DATE
CENTER
LARGE: Normally select this.
SMALL: Select this if small
speakers are used for the center
speaker.
Change the date information order of a JPEG
image in the Control Menu.
MM/DD/YYYY
YYYY/MM/DD
DD/MM/YYYY
YYYY/DD/MM
NONE: Select this if no center
speaker is used.
YYYY: Year
MM: Month
DD: Day
70US
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying the surround speaker
position and height
If you select anything other than “NONE” in
“SURROUND,” specify the size, position, and
height of the surround speakers.
SURROUND
LARGE (BEHIND, LOW),
LARGE (BEHIND, HIGH),
LARGE (SIDE, LOW),
LARGE (SIDE, HIGH),
SMALL (BEHIND, LOW),
SMALL (BEHIND, HIGH),
SMALL (SIDE, LOW),
BEHIND (LOW):
BEHIND (HIGH):
SIDE (LOW):
Select this if the surround
speakers are located in section
B and D.
SMALL (SIDE, HIGH):
Specify the size, position, and height
to implement the Digital Cinema
Surround modes in the sound field
(page 46) properly. For details, see
“Specifying the surround position
and height” as below.
Select this if the surround
speakers are located in section
B and C.
Select this if the surround
speakers are located in section
A and D.
NONE: Select this if no surround
speaker is used.
SURROUND
BACK
LARGE: Normally select this.
SMALL: Select this if small
speakers are used for the surround
back speaker.
SIDE (HIGH):
Select this if the surround
speakers are located in section
A and C.
NONE: Select this if no surround
back speaker is used.
These parameters are not available when
“SURROUND” is set to “NONE.”
SUBWOOFER
YES: Select this if a subwoofer is
Position diagram
used.
NONE: Select this if no subwoofer
is used.
Setting restrictions
Size setup has some restrictions. Some settings
are changed automatically.
90
If “FRONT” is set to “SMALL”
A
A
45
B
B
“CENTER,” “SURROUND,” and
“SURROUND BACK” must be set to either
“SMALL” or “NONE.”
20
Height diagram
If “SURROUND” is set to either “LARGE” or
“SMALL”
“SURROUND BACK” must be set to the same
setting or “NONE.”
C
D
C
If “SUBWOOFER” is set to “NONE”
60
“FRONT” must be set to “LARGE.”
D
30
Notes
• When you select an item, the sound cuts off for a
moment.
• Depending on the settings, subwoofer output may be
excessive.
Tip
Surround speaker position and height is
designed specifically for CINEMA STUDIO
EX mode.
continued
71US
Download from Www.Somanuals.com. All Manuals Search And Download.
x DISTANCE
x LEVEL
The default distance setting for the speakers in
relation to the listening position is shown below.
You can vary the level of each speaker as
follows. Be sure to set “TEST TONE” to “ON”
for easy adjustment.
CENTER
0 dB
Adjusts the level of the center
speaker (–10 dB to +10 dB, 1 dB
steps).
3m
(10ft)
3m
(10ft)
3m
(10ft)
SURROUND
LEFT 0 dB
SURROUND
RIGHT 0 dB
Adjusts the level of the surround
speakers (–10 dB to +10 dB, 1 dB
steps).
SURROUND
BACK 0 dB
Adjusts the level of the surround
back speaker (–10 dB to +10 dB,
1 dB steps).
3m
(10ft)
3m
(10ft)
3m
(10ft)
SUBWOOFER
0 dB
Adjusts the level of the subwoofer
(–10 dB to +10 dB, 1 dB steps).
x BALANCE
Be sure to change the value in the Setup Display
when you move the speakers.
You can vary the balance of the left and right
speakers as follows. Be sure to set “TEST
TONE” to “ON” for easy adjustment.
FRONT
3 m/10 ft
Front speaker distance from the
listening position can be set in 0.3
metre (1 ft) increments from 0.9 to 6.9
metres (3 to 23 ft).
FRONT
CENTER
Adjusts the balance between the front left
and right speakers. The center position is
shown as “---”. (You can adjust from the
center, 6 steps left or right.)
CENTER
3 m/10 ft
Center speaker distance can be moved
up to 1.5 metres (5 ft) forward closer
to your listening position from the
front speaker position, in 0.3 metre
(1 ft) increments.
To adjust the volume of all the
speakers at one time
Use the VOLUME control on the receiver, or
press VOLUME +/– on the remote.
SURROUND
3 m/10 ft
Surround speaker distance can be
moved up to 4.5 metres (15 ft) closer
to your listening position from the
front speaker position, in 0.3 metre
(1 ft) increments.
x TEST TONE
The speakers will emit a test tone to adjust
“LEVEL” and “BALANCE.”
SURROUND
BACK
3m/10ft
Surround back speaker distance can
be moved up to 4.5 metres (15 ft)
closer to your listening position from
the front speaker position, in 0.3 metre
(1 ft) increments.
OFF
ON
The test tone is not emitted from the
speakers.
The test tone is emitted from each speaker
in sequence. When “BALANCE” is
selected, the test tone is emitted from both
left and right speakers simultaneously.
When “LEVEL” is selected, the test tone is
emitted from only the speaker that you are
adjusting.
Notes
• When you set the distance, the sound cuts off for a
moment.
• If all front and surround speakers are not placed at an
equal distance from your listening position, set the
distance according to the closest speaker.
• Do not place the surround speakers farther away from
your listening position than the front speakers.
72US
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the speaker
balance and level by using the
test tone
1
Press DVD SETUP in stop mode.
The Setup Display appears.
2
Press X or x repeatedly to select
“SPEAKER SETUP,” then press
ENTER.
3
4
Press X or x repeatedly to select “TEST
TONE,” then press ENTER.
Press X or x repeatedly to select “ON,”
then press ENTER.
You will hear the test tone from each
speaker in sequence.
5
From your listening position, adjust the
value of “BALANCE” and “LEVEL”
using C/X/x/c.
When selecting “BALANCE,” the test tone
is emitted from both left and right speakers
simultaneously.
When selecting “LEVEL,” the test tone is
emitted from only the speaker which you
are adjusting.
6
7
8
Press ENTER when you have finished
making adjustments.
Press X or x repeatedly to select “TEST
TONE,” then press ENTER.
Press X or x repeatedly to select
“OFF,” then press ENTER.
Note
When you adjust the speaker settings, the sound cuts
off for a moment.
Tip
To adjust the balance or the level without
listening to the test tone, select “BALANCE” or
“LEVEL” in step 3 and press ENTER. Then
adjust the balance or level using X/x and press
ENTER.
73US
Download from Www.Somanuals.com. All Manuals Search And Download.
The picture is black and white.
• Depending on the TV, the picture on the screen
becomes black and white when you play a disc
recorded in the NTSC color system.
Additional Information
Troubleshooting
Sound
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should any
problem persist, consult your nearest Sony
dealer.
There is no sound.
• The speaker cord is not connected securely.
• The connecting cord is damaged. Replace it with
a new one.
• Press MUTING on the remote if “MUTING ON”
is displayed in the front panel display.
• The receiver is in pause mode or in Slow-motion
Play mode. Press H to return to normal play
mode.
Power
The power is not turned on.
• Check that the AC power cord is connected
securely.
• Fast forward or fast reverse is performed. Press
H to return to normal play mode.
Picture
• Select “DEC. PRI.” from AMP MENU and set
“AUTO” when playing DTS-CD signals from
external equipment using the DIGITAL IN
(OPTICAL IN/COAXIAL IN) jack (page 49).
There is no picture.
• The video connecting cords are not connected
securely.
The left and right sounds are unbalanced or
reversed.
• The video connecting cords are damaged.
• The receiver is not connected to the correct TV
• Check that the speakers and components are
connected correctly and securely.
• Adjust the balance parameter in the BALANCE
• The video input on the TV is not set so that you
can view pictures from the receiver.
• You have set “COMPONENT OUT” in
“SCREEN SETUP” to “PROGRESSIVE” even
though your TV cannot accept the signal in
progressive format. In this case, press and hold x
and . simultaneously for a few seconds. The
“COMPONENT OUT” setting returns to
“INTERLACE.”
There is no sound from the subwoofer.
• Check the speaker connections and settings (pages
• Set the sound field to “AUTO FORMAT DIRECT
Severe hum or noise is heard.
• Even if your TV is compatible with progressive
format (480p) signals, the image may be affected
when you set “COMPONENT OUT” to
“PROGRESSIVE.” In this case, set
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 metres (10
feet) away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
“COMPONENT OUT” to “INTERLACE.”
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output from your receiver goes
through your VCR to get to your TV, the copy-
protection signal applied to some DVD programs
could affect picture quality. If you still experience
problems even when you connect your receiver
directly to your TV, try connecting your receiver
• Select “DEC. PRI.” from AMP MENU and set
“AUTO” when playing DTS-CD signals from
external equipment using the DIGITAL IN
(OPTICAL IN/COAXIAL IN) jack (page 49).
• Clean the disc.
When CD (PCM signal) playback starts, sound
is not output initially.
Even though you set the aspect ratio in “TV
TYPE” of “SCREEN SETUP,” the picture does
not fill the screen.
• Select “DEC. PRI.” from AMP MENU and set
• The aspect ratio on the disc is fixed.
74US
Download from Www.Somanuals.com. All Manuals Search And Download.
The sound loses stereo effect when you play a
VIDEO CD, a CD, or an MP3.
The remote does not function.
• The controllable source on the remote is another
unit(s). Press DVD,VIDEO1, VIDEO 2, or
• There are obstacles between the remote and the
receiver.
• Set “AUDIO” to “STEREO” in the Control Menu
• Make sure the receiver is connected appropriately.
The surround effect is difficult to hear when
you are playing a Dolby Digital or MPEG audio
sound track.
• The distance between the remote and the receiver
is too far.
• The remote is not pointed at the remote sensor on
the receiver.
• Make sure the sound field function is on
• The batteries in the remote are weak.
• Check the speaker connections and settings (pages
The disc does not play.
• Depending on the DVD, the output signal may not
be the entire 5.1 channel or 6.1channel. It may be
monaural or stereo even if the sound track is
recorded in Dolby Digital or MPEG audio format.
• There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down
on the disc tray.
• The disc is skewed on the disc tray.
• The receiver cannot play CD-ROMs, etc.
The sound comes from the center speaker
only.
• Depending on the disc, the sound may come from
the center speaker only.
• The region code on the DVD does not match the
receiver.
No sound is heard from the center speaker.
• Check the speaker connections and settings.
• Make sure the sound field function is on
• Moisture has condensed inside the receiver.
Remove the disc and leave the receiver turned on
The MP3 audio track cannot be played.
• The DATA CD is not recorded in an MP3 format
that conforms to ISO9660 Level 1/ Level 2 or
Joliet.
No sound or only a very low-level sound is
heard from the surround/surround back
speakers.
• Check the speaker connections and settings.
• Make sure the surround speakers are set to either
“SMALL” or “LARGE.”
• The MP3 audio track does not have the extension
“.MP3.”
• The data is not formatted in MP3 even though it
has the extension “.MP3.”
• Make sure the sound field function is on
• The receiver can only play MP3 (MPEG1 Audio
Layer3) audio.
• Select a sound field containing the word
• Remove the disc and select “CUSTOM SETUP”
from the setup items. Then select “DATA CD
• There are more than 8 directory levels.
• Depending on the source, the effect of the
surround/surround back speakers may be less
noticeable.
Operation
The title of the MP3 audio album or track is not
correctly displayed.
Radio stations cannot be tuned in.
• Check that the antennas are connected securely.
Adjust the antennas or connect an external
antenna if necessary.
• The receiver can only display alphabetical letters
and numbers. Other characters are displayed as
“ ”.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use
manual tuning.
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
• Press DISPLAY/JUMP so that the frequency
appears in the display.
continued
75US
Download from Www.Somanuals.com. All Manuals Search And Download.
The JPEG image file cannot be played
• The DATA CD is not recorded in a JPEG format
that conforms to ISO9660 Level1/Level 2 or
Joliet.
You cannot perform some functions such as
Stop, Search, Slow-motion Play, Repeat Play,
Shuffle Play, or Program Play.
• Depending on the disc, you may not be able to
perform some of the operations above. See the
operating manual that came with the disc.
• The JPEG image file does not have the extension
“.JPG” or “.JPEG.”
• The data is not formatted in JPEG even though it
has the extension “.JPG” or “JPEG.”
Messages do not appear on the screen in the
language you want.
• Image length or width is more than 4720 dots.
• Remove the disc and select “CUSTOM SETUP”
from the setup items. Then select “DATA CD
• There are more than 8 directory levels.
• You cannot play the Progressive JPEG files.
• In the Setup Display, select the desired language
for the on-screen display in “OSD” under
“LANGUAGE SETUP” (page 67).
The language for the sound track cannot be
changed.
• Multilingual tracks are not recorded on the DVD
being played.
The title of a JPEG album or file is not
correctly displayed.
• The DVD prohibits changing the language for the
sound track.
• The receiver can only display alphabetical letters
and numbers. Other characters are displayed as
“ ”.
The subtitle language cannot be changed.
• Multilingual subtitles are not recorded on the
DVD being played.
The display for entering the password does
not appear for Super Audio CD, even though
Custom Parental Control is set.
• The DVD prohibits changing the subtitles.
The subtitle cannot be turned off.
• Custom Parental Control is set for different layers
of a Super Audio CD.
• The DVD prohibits turning off subtitles.
The angles cannot be changed.
• Multi-angles are not recorded on the DVD being
A disc does not start playing from the
beginning.
• Program Play, Shuffle Play, or Repeat Play has
Press CLEAR to cancel these functions before
playing a disc.
• The DVD prohibits changing the angles.
A disc cannot be ejected and “LOCKED”
appears in the front panel display.
• Contact your Sony dealer or local authorized Sony
service facility.
• Resume Play has been selected.
During stop, press x on the receiver or the remote
• The title, DVD or PBC menu automatically
appears on the TV screen.
“PROTECT” appears in the front panel
display.
• The speaker protection circuit is functioning.
• Check the speaker connections.
The receiver starts playing the disc
automatically.
The receiver does not work normally.
• If the receiver’s operation becomes effected, press
POWER on the receiver to turn off the power,
then turn on the power again.
• The DVD features an auto playback function.
Playback stops automatically.
• Some discs may contain an auto pause signal.
While playing such a disc, the receiver stops
playback at the auto pause signal.
The receiver turns off during DVD playback.
• If approximately one hour passes with DVD
playback paused or with the DVD top menu or a
DVD menu displayed during DVD playback, the
receiver automatically turns off.
76US
Download from Www.Somanuals.com. All Manuals Search And Download.
FM tuner section
System
PLL quartz-locked digital
synthesizer system
87.5 – 108.0 MHz (100
kHz step)
FM wire antenna
75 ohms, unbalanced
10.7 MHz
Specifications
Tuning range
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND
TOTAL HARMONIC
Antenna
Antenna terminals
Intermediate frequency
DISTORTION:
With 8 ohm loads, both
channels driven, from
20 – 20,000 Hz; rated
100 watts per channel
minimum RMS power,
with no more than 0.7 %
total harmonic distortion
from 250 milli watts to
rated output.
AM tuner section
System
PLL quartz-locked digital
synthesizer system
530 – 1710 kHz (with the
interval set at 10 kHz)
531 – 1710 kHz (with the
interval set at 9 kHz)
Loop antenna
Tuning range
Antenna
Amplifier section
Intermediate frequency
450 kHz
Stereo mode
100 W + 100 W (8/4 ohms,
20 – 20,000 Hz, THD 0.7
%)
Front: 100 W + 100 W
Center*: 100 W
Surround*: 100W +100 W
Surround back*: 100 W
(8/4 ohms, 20 – 20,000 Hz,
THD 0.7 %)
Video section
Inputs
Video:
1 Vp-p 75 ohms
S-video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
Video:
1 Vp-p 75 ohms
S-video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
Component:
Y: 1 Vp-p 75 ohms
PB/CB: 0.7 Vp-p
PR/CR: 0.7 Vp-p
Surround mode
Outputs
*
Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analogue)
Inputs (Digital)
ANALOG IN:
Sensitivity: 150 mV
Impedance: 50 kilohms
DIGITAL IN OPTICAL:
DIGITAL IN
COAXIAL:
General
Impedance: 75 ohms
SUB WOOFER OUT:
Voltage: 3 V
Impedance: 100 ohms
PHONES:
Accepts low- and high-
impedance headphones
DIGITAL OUT
Power requirements
Power consumption
120 V AC, 60 Hz
180 W
1 W (at the Power Saving
Mode)
Outputs (Analogue)
Outputs (Digital)
Dimensions (approx.)
430 × 100 × 450 mm (17 ×
3
4 × 17 /4 inches) (w/h/d)
incl. projecting parts
7.0 kg (15 lb 7 oz)
5°C to 35°C (41°F to 95°F)
5 % to 90 %
Mass (approx.)
Operating temperature
Operating humidity
Supplied accessories
OPTICAL
Super Audio CD/DVD system
See page 13.
Laser
Semiconductor laser
(Super Audio CD/DVD:
λ = 650 nm)
Design and specifications are subject to change
without notice.
(CD: λ = 780 nm)
Emission duration:
continuous
Signal format system
NTSC
77US
Download from Www.Somanuals.com. All Manuals Search And Download.
x Movie mode
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby
Surround. The result is enhanced soundfield
directionality that approaches the quality of
discrete 5.1-channel sound.
Glossary
Album
Section of a music piece or an image on a data
CD containing MP3 audio tracks or JPEG files.
x Music mode
Chapter
The Music mode is for use with any stereo music
recordings, and provides a wide and deep sound
space.
Subdivision of a title on a DVD. A title is
composed of several chapters.
Digital Cinema Sound (DCS)
This is the generic name of the surround sound
produced by digital signal processing
technology developed by Sony. Unlike previous
surround sound fields mainly directed at the
reproduction of music, Digital Cinema Sound is
designed specifically for the enjoyment of
movies.
Dolby Surround Pro Logic
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four
channels from two-channel sound. Compared
with the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right
panning more naturally and localizes sounds
more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of
surround speakers and a center speaker. The
surround speakers output monaural sound.
Dolby Digital
This movie theatre sound format is more
advanced than Dolby Surround Pro Logic. In
this format, the surround speakers output stereo
sound with an expanded frequency range, and a
subwoofer channel for deep bass is
independently provided. This format is also
called “5.1,” with the subwoofer channel
designated as the 0.1 channel (since it functions
only when a deep bass effect is needed). All six
channels in this format are recorded separately
for superior channel separation. Furthermore,
since all the signals are processed digitally, less
signal degradation occurs.
DTS
Digital audio compression technology
developed by Digital Theater Systems, Inc. This
technology conforms to 5.1-channel surround.
This format comprises of stereo surround
channels and a discrete subwoofer channel. DTS
provides the same 5.1 discrete channels of high
quality digital audio. Superior channel
separation is realized due to all channel data
being recorded discretely and processed
digitally.
Dolby Digital EX
DTS-ES
An enhanced compatible format of Dolby
Digital 5.1, developed by Dolby Laboratories
and Lucasfilm THX, which adds an extra
surround back channel, and can be used for
6.1(three surround speakers) channel playback,
using matrix encoding.
An enhanced compatible format of 5.1 channel,
which adds an extra surround back channel.
There are two formats: Discrete 6.1, which
processes the surround back signal
independently, and Matrix 6.1, which processes
it along with the Surround (L/R) channels.
Dolby Pro Logic II
DVD
Dolby Pro Logic II creates five full-bandwidth
output channels from two-channel sources. This
is done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same as
a CD.
The data capacity of a single-layer and single-
sided DVD, at 4.7 GB (Giga Byte), is 7 times
that of a CD. Furthermore, the data capacity of a
dual-layer and single-sided DVD is 8.5 GB, a
78US
Download from Www.Somanuals.com. All Manuals Search And Download.
single-layer and double-sided DVD 9.4 GB, and
a dual-layer and double-sided DVD 17 GB.
The picture data uses the MPEG 2 format, a
worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 of its original size. DVD also uses
variable rate coding technology that processes
allocated data according to the status of the
picture.
The audio data is recorded in Dolby Digital as
well as in PCM, allowing you to enjoy more
realistic audio presence.
Furthermore, various advanced functions such
as the multi-angle, multilingual, and Parental
Control functions are provided with the DVD.
channels to enhance the 6.1 channel effect, and
is best suited for movies.
MUSIC mode allows the front L and R channels
to go unprocessed for optimum stereo, with the
addition of the surround components adding a
special quality to the sound.
Parental Control
A function of the DVD to limit playback of the
disc by the age of the viewer according to the
limitation level in each country. The limitation
varies from disc to disc; when it is activated,
playback is completely prohibited, violent
scenes are skipped or replaced with other scenes
and so on.
Playback Control (PBC)
Signals encoded on VIDEO CDs (Version 2.0)
to control playback.
By using menu screens recorded on VIDEO
CDs with PBC functions, you can enjoy playing
simple interactive programs, programs with
search functions, and so on.
File
Section of a picture on a data CD containing
JPEG image files.
Film based software, Video based
software
DVDs can be classified as Film based or Video
based software. Film based DVDs contain the
same images (24 frames per second) that are
shown at movie theatres. Video based DVDs,
such as television dramas or sit-coms, displays
images at 30 frames (or 60 fields) per second.
Progressive format (sequential
scanning)
In contrast to the Interlace format, the
progressive format can reproduce 60 frames per
second by reproducing all scanning lines (525
lines for the NTSC system). The overall picture
quality increases and still images, text and
horizontal lines appear sharper. This format is
compatible with the 525 progressive format.
Interlace format (Interlaced
scanning)
The Interlace format is the NTSC standard
method for displaying TV images at 30 frames
per second. Each frame is scanned twice -
alternately between the even numbered scanning
lines and then odd numbered scanning lines, at
60 times per second.
Region Code
This receiver is used to protect copyrights. A
region number is allocated on each DVD system
or DVD disc according to the sales region. Each
region code is shown on the receiver as well as
on the disc packaging. The receiver can play the
discs that match its region code. The receiver
Multi-angle function
Various angles of a scene, or viewpoints of the
video camera are recorded on some DVDs.
ALL
can also play discs with the “ ” mark. Even
when the region code is not shown on the DVD,
the region limit may still be activated.
Multilingual function
Several languages for the sound or subtitles in a
picture are recorded on some DVDs.
Scene
Neo:6
On a VIDEO CD with PBC (playback control)
functions, the menu screens, moving pictures
and still pictures are divided into sections called
“scenes.”
Developed by Digital Theater Systems, Inc.,
applies a conventional 2-channel or Dolby
Digital source signal to a high-precision, digital
matrix decoder to achieve 6.1 channel surround
playback.
CINEMA mode allows for more separation of
continued
79US
Download from Www.Somanuals.com. All Manuals Search And Download.
Super Audio CD
• 2 channel + Multi-channel Super Audio CD
This disc consists of a 2 channel playback area
and a multi-channel playback area.
A Super Audio CD disc can reproduce sounds
that are extremely faithful to the original sound
by use of DSD (Direct Stream Digital)
technology. This technology utilizes a sampling
frequency of 2.8224 MHz, which is 64 times that
of a conventional CD, and 1-bit quantization that
enables the disc to hold 4 times the amount of
information that a standard PCM format CD can
hold. Super Audio CDs are divided into the
following types.
2 channel playback area
Multi-channel playback
area
Title
The longest section of a picture or music feature
on a DVD, movie, etc., in video software, or the
entire album in audio software.
• Super Audio CD (single layer disc)
This disc consists of a single HD layer*.
* High density signal layer for the Super Audio CD
Track
Section of a picture or a music piece on a Super
Audio CD, CD, VIDEO CD or MP3. An album
is composed of several tracks (MP3 only).
HD (high density) layer
VIDEO CD
A compact disc that contains moving pictures.
The picture data uses the MPEG 1 format, a
worldwide standard of digital compression
technology. The picture data is compressed to
about 1/140 of its original size. Consequently, a
12 cm VIDEO CD can contain up to 74 minutes
of moving pictures.
• Super Audio CD (dual layer disc)
This disc consists of dual HD layers and is
capable of extended play over long periods.
Also, as the dual layer disc consists of dual HD
layers on one side only, you do not have to turn
the disc over during playback.
VIDEO CDs also contain compact audio data.
Sounds outside the range of human hearing are
compressed while sounds we can hear are not
compressed. VIDEO CDs can hold 6 times the
audio information of conventional audio CDs.
There are 2 versions of VIDEO CDs.
• Version 1.1: You can play only moving
pictures and sounds.
HD layer
HD layer
• Super Audio CD + CD (Hybrid disc)
This disc consists of an HD layer and a CD
layer. Also, as the dual layers are on one side
only, you do not have to turn the disc over
during playback. You can play this CD layer
using a conventional CD player.
• Version 2.0: You can play high-resolution still
pictures and enjoy PBC functions.
This receiver conforms to both versions.
CD layer
HD layer
80US
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to Parts and Controls
For more information, refer to the pages indicated in parentheses.
Front Panel
VOLUME
POWER
STANDBY
SOUND FIELD
2CH
A. F. D.
MODE
DISPLAY
TUNER/PRESET
FUNCTION
PHONES
(remote sensor) (13)
C
D 2CH (44)
I MULTI CHANNEL DECODING indicator
continued
81US
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Display
When playing back a DVD
Lights up when you can change the angle
Playing status
SACD
HYBRID
ALL 1DISCS
DVD
CD
VIDEO CD
ANGLE
MP3
PBC NTSC PROGRESSIVE
MONO ST S
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Current chapter
number
Playing time
Current sound
Current title
number
Current mode
When playing back a Super Audio CD, CD, VIDEO CD, or MP3
Lights up during PBC
playback (VIDEO CD only)
Current play mode
Current disc
Current sound
SACD
ALL 1DISCS
DVD
CD
VIDEO CD
HYBRID
ANGLE
MP3
PBC NTSC PROGRESSIVE
MONO ST S
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Current index number
(The index indicator does
not appear during Super
Audio CD or MP3 play
back.)
Playing status Current track
Playing time
number
When listening to the radio
Preset number
Monaural/Stereo effect
SACD
ALL 1DISCS
DVD
CD
VIDEO CD
PBC NTSC PROGRESSIVE
HYBRID
ANGLE
MP3
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
MONO ST S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Current band
Current station
When playing back a JPEG file
Playing status
SACD
ALL 1DISCS
DVD
CD
VIDEO CD
PBC NTSC PROGRESSIVE
HYBRID
ANGLE
MP3
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
MONO ST S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Current mode
Current file number
82US
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
PB/CB
PR/CR
AM
Y
COAXIAL
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
L SUB WOOFER (ANALOG OUT) jack
R DIGITAL (OPTICAL IN VIDEO2) jack
T DIGITAL (COAXIAL IN TV/SAT) jack
continued
83US
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
ez m/M, SLOW
/
, TUNIING –/+
Notes
• This remote control glows in the dark. However,
before glowing, the remote must be exposed to light
for a while.
• When you operate a DVD player, press DVD 4, and
then change the mode of the receiver to DVD.
F 2CH (44)
84US
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code
Language
Code
Language
Code
Language
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
Afar
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
1345
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1436
1463
1481
1482
1483
Inupiak
1489
1491
1495
1498
1501
1502
1503
1505
1506
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali; Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Latin
Lingala
Welsh
Danish
German
Bhutani
Greek
Laothian
Lithuanian
Latvian; Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Twi
Ukrainian
Urdu
Frisian
Irish
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Punjabi
Uzbek
Vietnamese
Volap k
Wolof
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Xhosa
Yoruba
Chinese
Zulu
Polish
Hindi
Pashto; Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Not specified
1703
Romanian
85US
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Setup Menu List
You can set the following items with the DVD Setup menu.
The default settings are underlined.
LANGUAGE SETUP
SCREEN SETUP
a)
OSD
(Selects the language
TV TYPE
4:3 LETTER
BOX
4:3 PAN SCAN
16:9
you want to use from the
displayed language list.)
ON
OFF
JACKET
PICTURE
SCREEN SAVER
BACKGROUND
a)
DVD MENU
(Selects the language
you want to use from the
displayed language list.)
GRAPHICS
a)
BLUE
AUDIO
(Selects the language
you want to use from the
displayed language list.)
BLACK
INTERLACE
PROGRESSIVE
COMPONENT OUT
a)
SUBTITLE
(Selects the language
you want to use from the
displayed language list.)
CUSTOM SETUP
a)
PARENTAL
LEVEL
OFF
8.
CONTROL
7. NC17
6.
5.
R
4. PG13
3.
PG
2.
1.
G
STANDARD
USA
OTHERSt
CHANGE PASSWORD
a)
TRACK
OFF
SELECTION
AUTO
b)
AUDIO
OFF
DRC
STANDARD
MAX
c)
DATA CD
MP3
PRIORITY
JPEG
JPEG DATE
MM/DD/YYYY
YYYY/MM/DD
DD/MM/YYYY
YYYY/DD/MM
a) DVD only
b) Dolby Digital sources only
c) MP3, JPEG only
86US
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER SETUP
LARGE
SMALL
LARGE
SMALL
NONE
SIZE
FRONT
CENTER
SURROUND LARGE (BEHIND, LOW)
LARGE (BEHIND, HIGH)
LARGE (SIDE, LOW)
LARGE (SIDE, HIGH)
SMALL (BEHIND, LOW)
SMALL (BEHIND, HIGH)
SMALL (SIDE, LOW)
SMALL (SIDE, HIGH)
NONE
SURROUND LARGE
BACK
SMALL
NONE
SUBWOOFER YES
NONE
DISTANCE
FRONT
0.9m – 6.9m/
3ft – 23ft
(3m/10ft)
CENTER
0.9m – 6.9m/
3ft – 23ft
(3m/10ft)
SURROUND 0.9m – 6.9m/
3ft – 23ft
(3m/10ft)
SURROUND 0.9m – 6.9m/
BACK
LEVEL CENTER
SURROUND
3ft – 23ft
(3m/10ft)
–10 dB – +10 dB
(0dB)
–10 dB – +10 dB
(0dB)
LEFT
SURROUND
RIGHT
–10 dB – +10 dB
(0dB)
SURROUND
BACK
–10 dB – +10 dB
(0dB)
SUBWOOFER
–10 dB – +10 dB
(0dB)
BALANCE
FRONT
6 steps left or right
(CENTER)
TEST
TONE
OFF
ON
RESET
YES
NO
87US
Download from Www.Somanuals.com. All Manuals Search And Download.
FR
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Précautions
AVERTISSEMENT
Sécurité
• Si un objet ou du liquide venait à pénétrer à l’intérieur
du boîtier, débranchez l’appareil et faites-le vérifier
par un personnel qualifié avant de le remettre en
marche.
Attention – L’utilisation d’instruments
optiques avec ce produit augmente le
risque de lésion oculaire.
• L’appareil n’est pas déconnecté du secteur tant qu’il
reste branché sur la prise secteur, même s’il a été mis,
proprement dit, hors tension.
Pour les clients canadiens
ATTENTION
• Débranchez l’appareil de la prise murale si vous
prévoyez de ne pas l’utiliser pendant une longue
période. Pour débrancher le cordon, tirez sur la fiche,
ne tirez jamais sur le cordon lui-même.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Installation
• N’installez pas l’appareil dans un espace confiné
comme dans une bibliothèque ou un meuble encastré.
• Prévoyez une circulation d’air suffisante de manière
à éviter toute surchauffe interne.
ATTENTION
POUR EVTER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE
DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
• Ne placez pas l’appareil sur une surface moelleuse
(comme un tapis, une couverture, etc.) ou près de
tissus (comme un rideau ou une tenture) risquant de
bloquer les fentes d’aération.
• N’installez pas l’appareil à proximité de sources de
chaleur telles que des radiateurs ou des conduites
d’air chaud, ni à des endroits exposés à la lumière
directe du soleil, à une poussière excessive, à des
vibrations mécaniques ou à des chocs.
®
ENERGY STAR est une marque
déposée aux Etats-Unis.
En tant que partenaire d’ENERGY
STAR , Sony atteste que son
produit répond aux
recommandations d’ENERGY
®
• N’installez pas l’appareil en position inclinée.
L’appareil est conçu pour fonctionner uniquement à
l’horizontale.
®
STAR en matière d’économie
d’énergie.
• Gardez l’appareil et les disques à l’écart de tout
équipement contenant des aimants magnétiques
puissants, par exemple des fours à micro-ondes ou de
puissants haut-parleurs.
• Ne posez pas d’objets lourds sur l’appareil.
• Si vous transportez l’appareil directement d’une
pièce froide dans une pièce chaude, de l’humidité
peut apparaître par condensation à l’intérieur de
l’appareil et endommager les lentilles.
La première fois que vous installez l’appareil ou
lorsque vous le déplacez d’un endroit frais vers un
endroit chaud, attendez environ une heure avant de le
faire fonctionner.
2FR
Download from Www.Somanuals.com. All Manuals Search And Download.
l’interrupteur POWER de l’appareil principal. Bien
que le voyant reste allumé pendant quelques temps, le
système est complètement hors tension.
Félicitations !
Nous vous remercions d’avoir fait l’acquisition
de cet ampli-tuner Super Audio CD/DVD de
Sony. Avant de le faire fonctionner, lisez
attentivement ce mode d’emploi et conservez-le
pour toute référence ultérieure.
Réglage du volume
N’augmentez pas le volume lorsque vous écoutez un
passage avec de très faibles niveaux d’entrée ou sans
signal audio. Vous risqueriez d’endommager les
enceintes au moment du passage caractérisé par un
niveau sonore de crête.
Précautions
Entretien
Nettoyez le boîtier, le panneau et les commandes avec
un chiffon doux légèrement imprégné d’une solution
détergente neutre. N’utilisez pas de tampons abrasifs,
de poudre à récurer ou de solvant tel que l’alcool ou la
benzine.
Sécurité
Si un objet ou du liquide venait à pénétrer à l’intérieur
du boîtier, débranchez l’ampli-tuner et faites-le vérifier
par un personnel qualifié avant de le remettre en
marche.
Pour toute question ou tout problème concernant votre
ampli-tuner, n’hésitez pas à consulter votre revendeur
Sony le plus proche.
Installation
• Installez l’ampli-tuner dans un endroit suffisamment
ventilé pour éviter toute surchauffe interne.
• En cas de volume élevé sur de longues périodes, le
boîtier devient chaud au toucher. Il ne s’agit pas d’un
dysfonctionnement. Cependant, il est conseillé de ne
pas le toucher. N’installez pas l’appareil dans un
espace confiné où la ventilation est faible car il y a un
risque de surchauffe.
Entretien des disques
N’utilisez pas les disques de nettoyage CD/DVD
disponibles dans le commerce. Ils risquent
d’endommager votre ampli-tuner.
Couleurs de votre écran de
téléviseur
Si les enceintes entraînent des irrégularités de couleur
sur votre écran de téléviseur, mettez ce dernier hors
tension, puis remettez-le sous tension 15 à 30 minutes
après. Si les irrégularités de couleurs persistent,
éloignez les enceintes du téléviseur.
• Ne bouchez pas les orifices de ventilation en posant
quelque chose sur l’ampli-tuner. Le système est
équipé d’un amplificateur haute puissance. Si les
orifices de ventilation de la partie supérieure sont
bouchés, l’ampli-tuner peut surchauffer et mal
fonctionner.
• N’installez pas l’ampli-tuner sur une surface molle,
telle qu’un tapis, qui risquerait de boucher les orifices
de ventilation situés sous l’ampli-tuner.
L’étiquette est située à l’arrière de l’appareil.
IMPORTANT
Attention : Cette ampli-tuner est capable de
• N’installez pas votre ampli-tuner à proximité de
sources de chaleur ou dans un endroit soumis aux
rayons du soleil, à une poussière excessive ou à des
chocs mécaniques.
maintenir indéfiniment l’affichage d’une image
vidéo fixe ou d’un menu sur l’écran de votre
téléviseur. En laissant une image vidéo fixe ou un
menu affiché sur votre téléviseur pendant une
période prolongée, vous risquez de provoquer des
dommages irréversibles au niveau de votre écran.
Les téléviseurs de projection sont particulièrement
sensibles à ce phénomène.
Fonctionnement
• Si l’ampli-tuner est transporté directement d’un endroit
froid à un endroit chaud ou s’il est installé dans une
pièce très humide, de la condensation risque de se
former sur l’optique située à l’intérieur de
l’ampli-tuner. Si cela se produit, votre ampli-tuner
risque de ne pas fonctionner correctement. Dans ce cas,
retirez le disque et laissez l’ampli-tuner sous tension
pendant environ 30 minutes jusqu’à ce que l’humidité
se soit complètement évaporée.
Transport de l’ampli-tuner
Lorsque vous transportez l’ampli-tuner, appliquez la
procédure ci-dessous afin de protéger le mécanisme
interne.
Retirez le disque. « NO DISC » s’affiche dans la
fenêtre d’affichage du panneau frontal. Mettez l’ampli-
tuner hors tension et débranchez son cordon
d’alimentation de la prise secteur.
• Avant de déplacer votre ampli-tuner, retirez tous les
disques. Sinon, vous risquez de les endommager.
• Par souci d’économie d’énergie, le système peut être
mis complètement hors tension à l’aide de
3FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Table des matières
Cet ampli-tuner peut lire les disques
Visualisation des informations relatives au
Sélection du mode de décodage Surround
Modification de la valeur d’impédance des
Insertion des piles dans la
Etape 1 : Raccordement des
Etape 2 : Raccordements des
Etape 3 : Raccordements du téléviseur et
Etape 4 : Raccordement du cordon
(VERROUILLAGE PARENTAL
PARENTAL)
Reprise de la lecture à l’endroit où vous
Lecture de CD VIDEO dotés de fonctions
Commande d’autres appareils avec la
Modification de la luminosité du panneau
Sélection de la langue des menus ou de la
Recherche d’un point spécifique sur un
Recherche d’un titre/chapitre/plage/index/
4FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Informations
Index des composants et des
Liste des paramètres du menu de
5FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Format des
disques
Logo des disques
A propos de ce mode
d’emploi
CD audio
• Les instructions contenues dans le présent
mode d’emploi décrivent les commandes de la
télécommande. Vous pouvez également
utiliser les commandes de l’ampli-tuner si
elles portent le même nom ou un nom analogue
à celles de la télécommande.
CD-R/CD-RW
(données
audio)
(fichiers MP3)
(fichiers
JPEG)
• Les symboles suivants sont utilisés dans ce
mode d’emploi.
Le logo « DVD VIDEO » est une marque
commerciale.
Symbole
Signification
Fonctions disponibles pour les
DVD VIDEO et les DVD-R/DVD-
RW en mode vidéo ou pour les
DVD+R/DVD+RW en mode vidéo
Terminologie relative aux
disques
Fonctions disponibles en mode CD
VIDEO
• Titre
Fonctions disponibles en mode CD
Il s’agit de la section la plus longue d’une
image ou d’un morceau musical sur un DVD,
d’un film, etc., pour un logiciel vidéo ou de
l’album entier pour un logiciel audio.
• Chapitre
Fonctions disponibles en mode
Super Audio CD et CD audio
Fonctions disponibles pour les
plages audio MP3*
Il s’agit d’une section d’une image ou d’un
morceau musical plus petite que les titres. Un
titre est composé de plusieurs chapitres.
Suivant le disque, il est possible qu’aucun
chapitre ne soit enregistré.
Fonctions disponibles pour les
fichiers JPEG
* MP3 (MPEG1 Audio Layer 3) est un format
standard de compression des données audio défini
par l’ISO/MPEG.
• Album
Il s’agit d’une section d’un morceau musical
ou d’une image sur un CD de données
contenant des plages audio MP3 ou des
fichiers JPEG.
Cet ampli-tuner peut lire
les disques suivants
• Plage
Il s’agit des sections d’une image ou d’un
morceau musical sur un CD VIDEO, Super
Audio CD, CD ou MP3.
Format des
Logo des disques
disques
DVD VIDEO
• Index (Super Audio CD, CD) / Index
vidéo (CD VIDEO)
Il s’agit d’un nombre divisant une plage en
sections pour localiser facilement l’endroit de
votre choix sur un CD VIDEO, Super Audio
CD ou CD. Selon le disque, il est possible
qu’aucun index ne soit enregistré.
Super Audio
CD
CD VIDEO
6FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Scène
A propos des CD multi-session
Sur un CD VIDEO doté de fonctions PBC
(page 25), les écrans de menu, les images
animées et les images fixes sont divisés en
sections appelées « scènes ».
• Fichier
• L’ampli-tuner peut lire des CD multi-session
lorsqu’une plage audio MP3 est contenue dans
la première session. Toutes les plages audio
MP3, enregistrées dans les sessions suivantes,
peuvent également être lues.
Il s’agit d’une section d’un CD de données
contenant des fichiers image JPEG.
• Cet ampli-tuner peut lire des CD multi-session
lorsqu’un fichier image JPEG est contenu dans
la première session. Tous les fichiers image
JPEG, enregistrés dans les sessions suivantes,
peuvent également être lus.
Disque
Structure
du DVD
Titre
Chapitre
Plage
Index
• Si des plages audio et des images au format de
CD musical ou au format de CD VIDEO sont
enregistrées dans la première session, seule
celle-ci est lue.
Structure
du CD
VIDEO,
Super
Audio CD
ou CD
Disque
Disque
Disque
Structure
MP3
Code local
Album
Plage
Album
Fichier
Votre ampli-tuner est identifié par un code local
indiqué à l’arrière de l’appareil et elle ne peut
lire que les DVD identifiés par un code local
identique.
Structure
JPEG
ALL
Les DVD identifiés par
être lus sur cet appareil.
peuvent également
Remarque sur les fonctions PBC
(commande de lecture) (CD
VIDEO)
Cet ampli-tuner est compatible avec les versions
1.1 et 2.0 des normes CD VIDEO. Vous pouvez
bénéficier de deux types de lecture selon le type
du disque.
Si vous tentez de lire un autre DVD, le message
« Lecture de ce disque interdite en raison des
limites de zone. » apparaît sur l’écran du
téléviseur. Suivant les DVD, il se peut
qu’aucune indication de code local ne soit
fournie, même si la lecture des DVD est interdite
par les limites de zone.
Type de
disque
Vous pouvez
Exemples de disques que
votre ampli-tuner ne peut pas
lire
CD VIDEO
sans fonctions
PBC (Disques
version 1.1)
Lire des vidéos (images
animées) et de la musique.
Il n’est pas en mesure de lire les disques
suivants :
CD VIDEO
avec fonctions
PBC
(Disques
version 2.0)
Lire des logiciels interactifs à
l’aide des écrans de menu
affichés sur votre écran de
téléviseur (lecture PBC), en plus
des fonctions de lecture vidéo
des disques Version 1.1. En
outre, vous pouvez lire des
images fixes de haute résolution,
si elles sont disponibles sur le
disque.
• Les CD-ROM (à l’exception des extensions
« .MP3 », « .JPG » ou « .JPEG »)
• Les CD-R/CD-RW autres que ceux enregistrés
dans les formats suivants :
– Format de CD musicaux
– Format de CD VIDEO
– Format MP3/JPEG conforme à la norme
ISO9660* Niveau 1/Niveau 2 ou à son
format étendu, Joliet
suite
7FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Les sections de données sur des CD-Extra
• Les DVD-ROM
Remarque sur la lecture des
DVD et CD VIDEO
• Les DVD audio
• Les DVD-RAM
Certaines opérations de lecture de DVD et de
CD VIDEO peuvent avoir été
• Les DVD-RW en mode d’enregistrement
vidéo (VR)
intentionnellement définies par les éditeurs de
logiciels. Etant donné que cet ampli-tuner lit des
DVD et des CD VIDEO conformément au
contenu défini par les éditeurs de logiciels, il se
peut que certaines fonctions de lecture ne soient
pas accessibles. Veuillez également vous référer
aux instructions fournies avec les DVD ou les
CD VIDEO.
• Les DVD+RW en mode d’enregistrement
vidéo (VR)
• Les fichiers JPEG progressifs
* Il s’agit d’un format logique de fichiers et de
dossiers sur les CD-ROM, défini par l’ISO
(Organisation internationale de normalisation).
Ne chargez pas les disques suivants :
• Les DVD ayant un code local différent
Droits d’auteur
• Les disques qui ne sont ni standard, ni de
forme circulaire (par exemple, en forme de
carte, de cœur ou d’étoile).
Ce produit est doté d’une technologie de
protection des droits d’auteur protégée par des
brevets américains et autres droits sur la
propriété intellectuelle. L’emploi de cette
technologie de protection des droits d’auteur
doit faire l’objet d’une autorisation par
Macrovision et est exclusivement réservé à une
utilisation dans le cercle familial et à d’autres
types de visionnage limités, sauf autorisation
expresse de Macrovision. Les opérations
d’ingénierie inverse et de démontage sont
interdites.
• Les disques recouverts de papier ou
d’autocollants.
• Les disques sur lesquels il reste des traces de
bande adhésive ou de cellophane.
Remarques au sujet des CD-R/CD-RW/DVD-
R/DVD-RW (mode vidéo)/DVD+R/DVD+RW
(mode vidéo)
Dans certains cas, les CD-R/CD-RW/DVD-R/DVD-
RW (mode vidéo)/DVD+R/DVD+RW (mode vidéo)
ne peuvent pas être reproduits sur ce lecteur en raison
de la qualité de l’enregistrement, de l’état du disque, ou
encore des caractéristiques de l’appareil ou du logiciel
d’enregistrement.
Le disque ne peut pas être lu s’il n’a pas été
correctement finalisé. Pour obtenir davantage
d’informations, consultez le mode d’emploi de
l’appareil d’enregistrement.
Remarquez qu’il n’est pas possible de lire des disques
au format Packet Write (écriture par paquets).
Cet appareil dispose du décodeur
ambiophonique à matrice adaptative Dolby*
Digital et Dolby Pro Logic (II) ainsi que du
Système DTS** Digital Surround.
* Fabriqué sous licence Dolby Laboratories.
« Dolby », « Pro Logic » et le symbole double-D
sont des marques commerciales de Dolby
Laboratories.
**Fabriqué sous licence de Digital Theater Systems,
Inc.
« DTS », « DTS-ES » et « Neo:6 » sont des marques
commerciales de Digital Theater Systems, Inc.
Disques audio encodés par des
technologies de protection des droits
d’auteur
Cet appareil est conçu pour la lecture de disques
conformes à la norme Compact Disc (CD).
Récemment, des disques audio encodés par des
technologies de protection des droits d’auteur ont été
mis en vente par certaines compagnies de disques.
Veuillez noter que, parmi ces disques, certains ne sont
pas conformes à la norme CD et qu’il est possible
qu’ils ne puissent pas être lus sur cet appareil.
8FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Remarques sur les disques
Manipulation des disques
• Pour que les disques restent propres, tenez-les
par la partie périphérique. Ne touchez jamais la
surface.
• Ne collez ni papier, ni ruban adhésif sur le
disque.
• N’exposez pas les disques au rayonnement
direct du soleil ou à des sources de chaleur,
telles que des conduits de chauffage, et ne les
laissez pas dans une voiture garée en plein
soleil étant donné que la température à
l’intérieur de l’habitacle risque d’augmenter
considérablement.
• Après avoir lu un disque, rangez-le dans son
boîtier.
Entretien
• Avant de lire un disque, nettoyez-le à l’aide
d’un chiffon de nettoyage.
Essuyez les disques en allant du centre vers
l’extérieur.
• N’utilisez pas de solvants, tels que la benzine,
les diluants, les nettoyants disponibles dans le
commerce ou les sprays antistatiques destinés
aux disques en vinyle.
Cet ampli-tuner peut uniquement lire les disques
de forme circulaire standard. L’utilisation d’un
autre type de disque (par exemple en forme de
carte, de cœur ou d’étoile) peut entraîner un
dysfonctionnement.
N’utilisez pas de disque accompagné d’un
accessoire disponible dans le commerce, comme
une étiquette ou un anneau.
9FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilisation du menu de commande
Utilisez le menu de commande pour sélectionner la fonction souhaitée. Le menu de commande
s’affiche lorsque la touche DVD DISPLAY est enfoncée. Pour plus de détails, reportez-vous aux pages
indiquées entre parenthèses.
Numéro du titre en cours de
lecture (CD VIDEO/Super Audio
CD/CD : numéro de plage)
Nombre total de
titres ou de plages
enregistrés
Nombre total de chapitres ou
d’index enregistrés
Nom du titre en
cours de lecture
Nom du disque ou
type de disque
Statut de lecture
(NLecture, XPause, xArrêt, etc.)
Numéro du chapitre en cours
de lecture (CD VIDEO/Super
Audio CD/CD : numéro
d’index)
DVD
DVD
Type du disque en
(
)
1 2 2 7 MAKING SCENE
cours de lecture
(
)
1 8 3 4
1 : 3 2 : 5 5
Durée de lecture
T
Réglage courant
Options
Icône du paramètre du menu
de commande sélectionné
1: ANGLAIS
2: FRANÇAIS
3: ESPAGNOL
Paramètres du menu de
commande
Nom de la fonction du
paramètre du menu de
commande sélectionné
Message d’instruction
SOUS-TITRE
Sélectionner :
ENTER
Liste des paramètres d’affichage du menu de commande
DISQUE
Affiche le nom du disque ou le type de disque inséré dans
l’appareil.
TITRE (DVD uniquement)
(page 36)/SCENE (CD VIDEO uniquement
en mode de lecture PBC) /PLAGE (CD
VIDEO uniquement) (page 36)
Sélectionne le titre (DVD) ou la plage (CD VIDEO) à lire.
Affiche la scène (CD VIDEO en mode de lecture PBC).
CHAPITRE (DVD uniquement)
(page 37)/INDEX (CD VIDEO uniquement)
Sélectionne le chapitre (DVD) ou l’index (CD VIDEO) à lire.
ALBUM (MP3 uniquement)
Sélectionne l’album (MP3) à lire.
PLAGE (Super Audio CD/CD/
Sélectionne la plage (Super Audio CD/CD/MP3) à lire.
INDEX (Super Audio CD/CD
uniquement) (page 37)
Affiche l’index et sélectionne l’index (Super Audio CD) à
lire.
Vérifie le temps écoulé et la durée de lecture restante.
Saisit le code temporel pour rechercher une image et de la
musique.
10FR
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO (DVD/CD VIDEO/ Super
Modifie le réglage audio.
Audio CD/CD/MP3 uniquement) (page 43)
SOUS-TITRE (DVD uniquement) Affiche les sous-titres.
Modifie la langue des sous-titres.
ALBUM (JPEG uniquement)
Sélectionne l’album (JPEG) à lire.
Sélectionne le fichier (JPEG) à lire.
Affiche les informations relatives à la date.
Modifie l’angle.
FICHIER (JPEG uniquement)
DATE (JPEG uniquement)
ANGLE (DVD uniquement)
MODE DE LECTURE (VIDEO
Sélectionne le mode de lecture.
CD/Super Audio CD/CD/MP3/JPEG
uniquement)(page 32)
REPETEE (page 33)
Lit tout le disque (tous les titres/toutes les plages), un titre/
chapitre/plage/album ou le contenu d’un programme en
boucle.
MODE IMAGE (DVD/CD VIDEO/ Règle de diverses manières le signal vidéo provenant de
l’ampli-tuner.
JPEG uniquement) (page 55)
Sélectionne le réglage le mieux adapté au programme
regardé.
VERROUILLAGE PARENTAL
PERSONNALISE (page 56)
Définit des restrictions de lecture pour le disque.
Conseils
• Chaque fois que vous appuyez sur DVD DISPLAY, l’affichage du menu de commande change comme indiqué ci-
après:
Affichage du menu de commande
m
Affichage du menu de commande désactivé
Les paramètres du menu de commande varient selon le disque.
• Le témoin icône du menu de commande s’allume en vert
REPETEE sur « NON ».
t
sauf si vous réglez le paramètre
• Le témoin « ANGLE » s’allume en vert uniquement lorsque plusieurs angles sont enregistrés sur le disque.
• Le témoin « MODE IMAGE » s’allume en vert si « STANDARD » n’est pas sélectionné.
11FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Insertion des piles dans la
télécommande
Préparation
Déballage
Vous pouvez commander l’ampli-tuner au
moyen de la télécommande fournie. Insérez
deux piles R6 (AA) en faisant correspondre les
pôles 3 et # des piles avec les signes
représentés à l’intérieur du compartiment. Pour
faire fonctionner la télécommande, dirigez-la
vers le capteur de télécommande de l’ampli-
tuner.
Assurez-vous que vous disposez de l’ensemble
des accessoires suivants :
• Antenne cadre AM (1)
• Fil d’antenne FM (1)
• Cordon S vidéo (1)
• Télécommande RM-SP500 (1)
• Piles R6 (AA) (2)
• Mode d’emploi (1)
Remarques
• Ne laissez pas la télécommande dans un endroit
extrêmement chaud ou humide.
• N’utilisez pas une pile neuve et une pile usagée
ensemble.
• Ne laissez rien tomber dans le boîtier de la
télécommande, en particulier lorsque vous remplacez
les piles.
• N’exposez pas le capteur de télécommande à la
lumière directe du soleil ou d’une lampe. Vous
risqueriez de l’endommager.
• Si vous prévoyez de ne pas utiliser la télécommande
pendant une période prolongée, retirez les piles pour
éviter qu’elles fuient et génèrent de la corrosion,
endommageant ainsi la télécommande.
• Lorsque vous utilisez l’ampli-tuner, sélectionnez la
fonction DVD ou TUNER.
12FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Etape 1 : Raccordement des enceintes
Vous pouvez profiter du son ambiophonique en raccordant 6 enceintes (enceintes avant gauche/droite,
enceinte centrale, enceintes surround gauche/droite et enceinte surround arrière) ainsi qu’un caisson de
graves actif à l’ampli-tuner. Si vous ne raccordez pas 6 enceintes et un caisson de graves actif, l’ampli-
tuner vous permet néanmoins d’optimiser le signal en fonction du nombre d’enceintes raccordées.
Lorsque vous raccordez 2 enceintes à l’ampli-tuner, branchez-les sur les prises SPEAKERS FRONT
L/R.
Remarques
• Veillez à faire correspondre les cordons des enceintes aux bornes appropriées : 3 à 3, # à #, L à L et R à R.
• Utilisez des enceintes haute impédance.
• Choisissez des enceintes avant, centrale, surround et surround arrière possédant une taille adéquate et offrant des
performances homogènes.
• Pour optimiser le son surround, spécifiez les paramètres des enceintes (taille, distance, niveau, etc.) à la page 74.
suite
13FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Bornes de raccordement des enceintes
Raccordez
A
Enceintes avant
Bornes SPEAKERS FRONT L et R
Bornes SPEAKERS SURROUND L et R
Borne SPEAKERS SURROUND BACK
Borne SPEAKERS CENTER
Prise SUBWOOFER AUDIO OUT
Enceintes surround
Enceinte arrière surround
Enceinte centrale
Caisson de graves
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
P
B/CB
PR/CR
AM
Y
COAXIAL
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
+
–
Enceinte centrale
–
+
+
–
Caisson de graves
(type actif)
Enceinte avant (R)
Enceinte avant (L)
+
–
+
–
+
–
Enceinte surround (L)
Enceinte surround (R)
Enceinte arrière surround
14FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Note sur le raccordement des cordons des enceintes à l’ampli-
tuner
3
Dénudez l’extrémité du cordon sur 10 mm ( /8 pouce) environ, puis torsadez les fils ainsi dénudés.
Raccordez les extrémités dénudées des cordons aux bornes en veillant à éviter tout contact entre les fils.
Assurez-vous que les cordons sont fermement raccordés aux bornes des enceintes et de l’ampli-tuner.
10 mm
(3/8 po.)
Pour éviter un court-circuit des enceintes
Un court-circuit au niveau des enceintes peut endommager l’ampli-tuner. Pour éviter cela, prenez les
précautions suivantes lors du raccordement des enceintes. Assurez-vous que le fil dénudé de chaque
cordon d’enceinte n’entre pas en contact avec une autre borne ou avec le fil dénudé d’un autre cordon
d’enceinte.
Exemples de mauvais raccordements des enceintes
Le cordon d’enceinte dont l’extrémité
est dénudée touche une autre borne
de l’enceinte.
Les cordons dont les extrémités sont
dénudées se touchent en raison d’une
suppression excessive de l’isolation.
Après avoir raccordé tous les composants, les enceintes et le cordon d’alimentation secteur, faites un
test de tonalité pour vérifier que toutes les enceintes sont raccordées correctement. Pour plus de détails
Si aucun son n’est émis par une enceinte lors d’un test de tonalité ou si la tonalité est émise par une
enceinte différente de celle apparaissant dans la fenêtre d’affichage du panneau frontal, l’enceinte est
peut-être court-circuitée. Dans ce cas, vérifiez une nouvelle fois son raccordement.
Remarques
• Veillez à faire correspondre le cordon de l’enceinte à la borne appropriée des composants : 3 à 3 et # à #. Si les
cordons sont inversés, le son est déformé et manque de graves.
• Si la puissance admissible nominale maximale des enceintes avant est faible, réglez soigneusement le volume de
l’ampli-tuner afin que son niveau de sortie ne soit pas trop élevé.
• Lorsque vous raccordez les extrémités dénudées des cordons des enceintes, veillez à ce qu’elles ne se touchent pas
et n’entrent pas en contact avec les bornes adjacentes.
15FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Etape 2 : Raccordements des antennes
Raccordez les antennes AM/FM fournies pour écouter la radio.
Bornes de raccordement des antennes
Raccordez
A
Antenne cadre AM
Fil d’antenne FM
Bornes AM
Prise FM 75 Ω COAXIAL
Antenne cadre AM
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
COAXIAL
P
B/CB
PR/CR
AM
Y
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
Fil d’antenne FM
Remarques
• Pour éviter de capter des parasites, éloignez l’antenne cadre AM de l’ampli-tuner et des autres composants.
• Veillez à déplier entièrement le fil d’antenne FM.
• Après avoir raccordé le fil d’antenne FM, maintenez-le aussi horizontal que possible.
• Lorsque vous raccordez l’antenne cadre AM fournie, raccordez le cordon noir (B) à la borne U et le cordon blanc
(A) à l’autre borne.
A
AM
B
16FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Si la réception FM est de mauvaise qualité
Utilisez un câble coaxial 75 ohms (non fourni) pour raccorder l’ampli-tuner à une antenne FM extérieure comme
illustré ci-dessous.
Antenne FM extérieure
Ampli-tuner
ANTENNA
FM
75
AM
COAXIAL
Fil de terre
(non fourni)
Vers la terre
Remarque
Si vous raccordez l’ampli-tuner à une antenne extérieure, mettez-la à la terre pour la protéger contre l’orage. Pour
éviter une explosion de gaz, ne raccordez pas le fil de terre à un tuyau de gaz.
17FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Etape 3 : Raccordements du téléviseur et des composants
vidéo
Cordons requis
Cordon S vidéo pour le raccordement d’un téléviseur
Cordons audio/vidéo (non fournis)
Lorsque vous raccordez un cordon, veillez à faire correspondre les broches à codes de couleur aux
prises appropriées des composants.
Jaune (vidéo)
Blanc (L/audio)
Rouge (R/audio)
Prises de raccordement des composants vidéo
Raccordez un
A
Téléviseur
Prise MONITOR (S VIDEO OUT ou VIDEO OUT)
Prises VIDEO 1 ou VIDEO 2 (S VIDEO IN ou VIDEO IN/AUDIO L/R IN)
Prises TV/SAT (S VIDEO IN ou VIDEO IN/AUDIO L/R IN)
Magnétoscope
Récepteur satellite numérique
Remarque
Lorsque l’ampli-tuner est en mode « DVD », aucun signal ne transite par les prises COMPONENT VIDEO OUT.
Conseil
Lorsque vous utilisez les prises COMPONENT VIDEO OUT (Y, PB/CB, PR/CR) plutôt que les prises
S vidéo ou les prises Vidéo, votre téléviseur doit également être raccordé par l’intermédiaire des prises
COMPONENT VIDEO OUT (Y, PB/CB, PR/CR). Si votre téléviseur accepte les signaux au format
progressif, vous devez utiliser cette connexion et régler « SORTIE COMPOSANTE » sur
18FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Téléviseur avec
Téléviseur avec
prise S VIDEO IN
Téléviseur
prises COMPONENT VIDEO IN
COMPONENT
VIDEO IN
INPUT
INPUT
VIDEO
IN
S
VIDEO
IN
Y
P
B/CB
P
R/CR
IN
IN
IN
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
COAXIAL
P
B/CB
PR/CR
AM
Y
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
OUT
OUT
OUT
OUT
OUT
DIGITAL OUT
(OPTICAL)
S
VIDEO
OUT
S
VIDEO
OUT
AV MULTI OUT
AUDIO
OUT
AUDIO
OUT
L
L
OUTPUT
R
R
OPTICAL
Récepteur satellite numérique
Magnétoscope
PlayStation 2
Si vous raccordez un récepteur satellite numérique avec prise OPTICAL
OUT ou COAXIAL OUT
Le récepteur satellite numérique peut être raccordé à la prise TV/SAT (OPTICAL ou COAXIAL)
INPUT plutôt qu’aux prises AUDIO IN L/R de l’ampli-tuner.
L’ampli-tuner accepte à la fois les signaux numériques et analogiques. Les signaux numériques sont
prioritaires sur les signaux analogiques. En cas d’interruption du signal numérique, le signal analogique
prend la relève après 2 secondes.
Si vous raccordez un récepteur satellite numérique sans prise OPTICAL
OUT
Raccordez le récepteur satellite numérique exclusivement aux prises S VIDEO IN ou VIDEO IN et
AUDIO IN L/R de l’ampli-tuner.
Pour écouter le son du téléviseur ou d’une console de jeux (PlayStation
2, par exemple) par l’intermédiaire de l’ampli-tuner
Raccordez les prises de sortie audio du téléviseur ou de la console de jeux aux prises VIDEO 2 (AUDIO
L/R IN ou OPTICAL IN) de l’ampli-tuner.
19FR
Download from Www.Somanuals.com. All Manuals Search And Download.
En cas d’irrégularités de couleur
sur le téléviseur
Réglage des enceintes
Si les enceintes sont installées trop près, des
irrégularités de couleur peuvent apparaître à
l’écran. Dans ce cas, mettez immédiatement le
téléviseur hors tension, puis remettez-le sous
tension après 15 à 30 minutes. Si les
irrégularités de couleur persistent, éloignez le
caisson de graves du téléviseur. Si les mesures
ci-dessus ne viennent pas à bout des irrégularités
de couleur, vérifiez qu’aucun objet magnétique
ne se trouve à proximité du caisson de graves.
Les irrégularités de couleur peuvent découler de
l’interaction entre le caisson de graves et un
objet magnétique.
Pour optimiser le son surround, toutes les
enceintes, hormis le caisson de graves, doivent
être à la même distance de la position d’écoute
(A).
Cependant, cet appareil vous permet de
rapprocher l’enceinte centrale jusqu’à 1,5 mètre
a) (B) et les enceintes surround et arrière
surround jusqu’à 4,5 mètres b) (C, D) de la
position d’écoute.
Les enceintes avant peuvent être placées entre
0,9 et 6,9 mètres c) (A) de la position d’écoute.
Equivalents numériques canadiens :
a) 5 pieds (1,5 mètre)
b) 15 pieds (4,5 mètres)
Parmi les exemples de sources d’interférences
magnétiques éventuelles, citons : les verrous
magnétiques d’un meuble TV notamment, les
appareils médicaux, les jouets, etc.
c) 3 à 23 pieds (0,9 à 6,9 mètres)
Disposez les enceintes de la manière illustrée ci-
dessous
Spécification des paramètres
des enceintes
B
Pour optimiser le son surround, commencez par
spécifier la taille et la distance des enceintes par
rapport à votre position d’écoute, puis réglez le
niveau et la balance. Utilisez le test de tonalité
pour régler le volume et la balance des enceintes
au même niveau.
A
A
45
C
C
90
Sélectionnez « REGLAGE H-P » dans le menu
de configuration. Pour plus de détails, reportez-
vous à la section « Réglages des enceintes »
Vous pouvez aussi modifier la valeur de
l’impédance en fonction de l’impédance de vos
enceintes. Pour plus d’informations, reportez-
vous à la section « Modification de la valeur
D
20
Remarque
Les enceintes centrale, surround et arrière surround ne
doivent pas être plus éloignées de la position d’écoute
que les enceintes avant.
21FR
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Appuyez sur la touche Z ou sur la
touche OPEN/CLOSE de l’ampli-tuner
et posez un disque dans le plateau de
lecture en dirigeant son étiquette vers
le haut.
Lecture de disques
Lecture de disques
L’ampli-tuner se met automatiquement
sous tension et le témoin STANDBY
s’éteint.
Certaines opérations peuvent être différentes ou
limitées selon les DVD ou CD VIDEO.
Reportez-vous aux instructions d’utilisation
fournies avec votre disque.
Témoin STANDBY
Nx
Z
POWER
FUNCTION –/+
Pour lire un disque de 8 cm, posez-le
dans le cercle intérieur du plateau
VOLUME
POWER
STANDBY
SOUND FIELD
2CH
A.
F
.
D.
MODE
DISPLAY
TUNER/PRESET
FUNCTION
PHONES
5
Appuyez sur H.
Le plateau de lecture se ferme et l’ampli-
tuner commence la lecture (lecture
continue). Réglez le volume sur l’ampli-
tuner.
Réglage
du volume
Plateau de lecture
Prise casque
"/1
Après l’étape 5
DVD
Suivant le disque, un menu peut s’afficher sur
l’écran du téléviseur. Vous pouvez lire le disque
en mode interactif en suivant les instructions du
page 25).
Pour retirer le disque
H
x
Appuyez sur la touche Z de l’ampli-tuner ou sur
la touche OPEN/CLOSE de la télécommande.
« OPEN » apparaît sur la fenêtre d’affichage du
panneau frontal. Retirez le disque lorsque le
plateau de lecture glisse hors de l’ampli-tuner.
OPEN/CLOSE
Pour mettre l’ampli-tuner sous
tension
1
2
Mettez votre téléviseur sous tension.
Appuyez sur la touche POWER de l’ampli-
tuner. L’ampli-tuner passe en mode de veille et
le témoin STANDBY s’allume en rouge.
Appuyez sur la touche "/1 de la télécommande.
L’ampli-tuner se met sous tension et le témoin
STANDBY s’éteint. En mode de veille, l’ampli-
tuner peut aussi être mis sous tension en
appuyant sur sa touche Z, FUNCTION –/+ ou
N, ou encore sur la touche DVD, OPEN/
CLOSE ou H de la télécommande.
Réglez le sélecteur d’entrée du
téléviseur sur votre ampli-tuner.
3
Appuyez sur la touche POWER de
l’ampli-tuner.
L’ampli-tuner passe en mode de veille et le
témoin STANDBY s’allume en rouge.
22FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Pour mettre l’ampli-tuner hors
tension
Pour
Appuyez sur
Passer au chapitre, à la
plage, à la scène ou au
fichier suivant en mode de
lecture continue
>
Appuyez sur la touche "/1 de la télécommande.
L’ampli-tuner passe en mode de veille et le
témoin STANDBY s’allume en rouge. Pour
éteindre complètement l’ampli-tuner, appuyez
sur sa touche POWER. Pendant la lecture d’un
disque, ne mettez pas l’ampli-tuner hors tension
en appuyant sur POWER. Cela risquerait
d’effacer les réglages des menus. Lorsque vous
mettez l’ampli-tuner hors tension, appuyez sur
x pour arrêter la lecture, puis appuyez sur la
touche "/1 de la télécommande.
Revenir au chapitre, à la
plage, à la scène ou au
fichier précédent en mode
de lecture continue
.
Arrêter la lecture et retirer le Z de l’ampli-tuner ou
disque
sur la touche OPEN/
CLOSE de la
télécommande.
Mettre le son en sourdine
MUTING. Pour
annuler l’effet de
sourdine, appuyez de
nouveau sur cette
touche ou sur
Economie d’énergie en mode de
veille
Appuyez une fois sur la touche "/1 de la
VOLUME + pour
régler le niveau du
volume.
télécommande.
Conseil
Quand l’ampli-tuner est en mode de veille, son témoin
STANDBY est allumé.
* Vous ne pouvez pas passer en mode pause en cours
de lecture JPEG.
Pour annuler le mode de veille
Appuyez une fois sur la touche "/1 de la
télécommande.
Remarques
• Refermez le plateau de lecture sans appuyer dessus.
Appuyez sur la touche Z de l’ampli-tuner ou sur la
touche OPEN/CLOSE de la télécommande pour
refermer le plateau de lecture.
Opérations complémentaires
• Si la lecture d’un DVD est interrompue pendant une
heure environ, l’ampli-tuner s’éteint
automatiquement.
./>
x
H
X
OPEN/
CLOSE
VOLUME
+/–
MUTING
Pour
Appuyez sur
Arrêter
x
X
Passer en mode pause*
Reprendre la lecture après X ou H
une pause
23FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Le point d’arrêt de la lecture n’est plus conservé en
mémoire si :
Reprise de la lecture à
l’endroit où vous avez
arrêté le disque
– vous modifiez le mode de lecture.
– vous modifiez le réglage du menu de
configuration.
Conseil
Pour reprendre la lecture depuis le début du disque,
appuyez deux fois sur x, puis appuyez sur H.
(Reprise de la lecture)
Lorsque vous arrêtez le disque, l’ampli-tuner
mémorise l’endroit où vous avez appuyé sur x
et l’indication « RESUME » apparaît dans la
fenêtre d’affichage du panneau frontal. La
fonction de reprise de la lecture continue à
fonctionner aussi longtemps que vous ne retirez
pas le disque, même si vous mettez l’appareil en
veille en appuyant sur la touche "/1.
H
x
1
2
Lorsque vous lisez un disque, appuyez
sur x pour arrêter la lecture.
L’indication « RESUME » apparaît dans la
fenêtre d’affichage du panneau frontal,
vous permettant de redémarrer le disque à
l’endroit où vous l’avez arrêté.
Si l’indication « RESUME » n’apparaît
pas, la fonction Reprise de la lecture n’est
pas accessible.
Appuyez sur H.
La lecture débute à l’endroit où le disque a
été arrêté à l’étape 1.
Remarques
• Selon la position d’arrêt, il est possible que l’ampli-
tuner ne reprenne pas la lecture exactement au même
endroit.
24FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilisation du menu du
DVD
Lecture de CD VIDEO dotés
de fonctions PBC
(Ver. 2.0)
(Lecture PBC)
Un DVD est divisé en longues sections qui
constituent une image ou un morceau de
musique. Ces sections sont appelées « titres ».
Lorsque vous lisez un DVD contenant plusieurs
titres, vous pouvez sélectionner celui de votre
choix à l’aide de la touche TOP MENU/GUIDE.
Lorsque vous lisez des DVD permettant de
sélectionner des options telles que la langue des
sous-titres et la langue de la bande son,
sélectionnez-les à l’aide de la touche AV
MENU.
Vous pouvez bénéficier d’une certaine
interactivité, à savoir utiliser des fonctions de
recherche ou d’autres fonctions du même type,
grâce aux fonctions PBC (commande de
lecture).
La lecture PBC vous permet de lire des CD
VIDEO en mode interactif en suivant le menu
affiché sur l’écran du téléviseur.
Touches
numériques
Touches
numériques
./>
TOP
MENU/
H
x
GUIDE
ENTER
C/X/x/c
AV MENU
ENTER
X/x
O RETURN/
EXIT
1
Appuyez sur TOP MENU/GUIDE ou AV
MENU.
1
2
Démarrez la lecture d’un CD VIDEO
doté de fonctions PBC.
Le menu du disque s’affiche sur l’écran du
téléviseur.
Le menu de votre sélection apparaît.
Sélectionnez le numéro du paramètre
souhaité en appuyant sur X/x ou sur
les touches numériques.
Le contenu du menu varie selon le disque.
2
3
Appuyez sur C/X/x/c ou sur les
touches numériques pour sélectionner
le paramètre que vous souhaitez lire ou
modifier.
3
4
Appuyez sur ENTER.
Suivez les instructions du menu pour
les opérations interactives.
Appuyez sur ENTER.
Reportez-vousaux instructionsd’utilisation
fournies avec le disque, car les procédures
peuvent différer selon les CD VIDEO.
Remarque
Si le menu principal du DVD ou un menu du DVD
demeure affiché pendant une heure environ au cours de
la lecture d’un DVD, l’ampli-tuner s’éteint
automatiquement.
suite
25FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Pour revenir au menu
Appuyez sur O RETURN/EXIT.
Lecture d’une plage audio
MP3
Remarques
• Selon le CD VIDEO, le menu n’apparaît pas à
l’étape 1.
• Selon le CD VIDEO, l’instruction « Appuyez sur
ENTER » de l’étape 3 peut être remplacée par
« Appuyez sur SELECT » dans les instructions
d’utilisation fournies avec le disque. Si c’est le cas,
appuyez sur H.
Vous pouvez lire des plages audio MP3 sur des
CD-ROM, CD-R ou CD-RW. Cependant, les
disques doivent être enregistrés conformément à
la norme ISO9660 niveau 1, niveau 2 ou au
format Joliet pour que l’ampli-tuner reconnaisse
les plages. Vous pouvez également lire des
disques enregistrés en multi-session. Reportez-
vous aux instructions de l’appareil CD-R/RW
ou du logiciel d’enregistrement (non fourni)
pour obtenir des détails sur le format
Conseil
Pour effectuer une lecture sans les fonctions PBC,
appuyez sur ./> ou sur les touches numériques,
alors que l’ampli-tuner est arrêté pour sélectionner une
plage, puis appuyez sur H ou ENTER.
L’indication « Lecture sans PBC » apparaît sur l’écran
du téléviseur, puis la lecture continue débute. Il est
impossible de lire des images fixes comme un menu.
Pour revenir à la lecture PBC, appuyez deux fois sur x,
puis sur H.
d’enregistrement.
1
2
Chargez un disque de données
enregistré en MP3 dans l’appareil.
Appuyez sur H.
L’appareil commence à lire la première
plage audio MP3 du premier album du
disque.
Remarques
• L’ampli-tuner peut lire des fichiers audio MP3
(MPEG1 Audio Layer3). L’appareil ne peut pas lire
les plages audio au format MP3PRO.
• L’ampli-tuner peut lire des CD multi-session
lorsqu’une plage audio MP3 se trouve dans la
première session. Toutes les plages audio MP3
ultérieures, enregistrées dans les sessions suivantes,
peuvent également être lues.
• Nombre maximal d’albums par disque : 99
(Un album ne peut pas contenir plus de 250 plages
audio MP3.)
• Un album dépourvu de plage audio MP3 est ignoré.
• Si vous attribuez l’extension « .MP3 » à des données
qui ne sont pas au format MP3, l’ampli-tuner ne peut
pas reconnaître les données correctement et génère un
bruit fort qui peut endommager les enceintes.
• Si l’ampli-tuner ne peut pas lire une plage MP3,
retirez le disque et sélectionnez « REGLAGE
PERSONNALISE » parmi les paramètres de
configuration. Sélectionnez ensuite « PRIORITE CD
DONNEES » et choisissez « MP3 » (page 73) avant
de réinsérer le disque.
• L’ampli-tuner peut lire jusqu’à une profondeur de 8
répertoires.
26FR
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Sélectionnez
l’aide de X/x, puis appuyez sur ENTER.
(PLAGE) à
Sélection d’un album et d’une
plage
La liste des plages figurant sur l’album en
cours apparaît.
HOME TOWN
MP3
ROCK BEST HIT
1.HIGHWAY
2.VIEW POINT
3.MY CHILDREN
4.DANCING
5.GOOD TASTE
6.DESTINATION
7.MARATHON
8.PLACE-KICK
9.TAKE IT EASY
10.PORT TOWER
11.STANDARD
ALBUM–
ALBUM+
ENTER
C/X/x/c
O RETURN/
EXIT
DVD
DISPLAY
Lorsque la liste de toutes les plages ou
albums ne peut pas être affichée, la barre de
défilement apparaît. Appuyez sur c pour
sélectionner l’icône de la barre de
défilement, puis déplacez-la pour afficher
le reste de la liste à l’aide de X/x. Appuyez
sur C ou O RETURN/EXIT pour revenir
à la liste des plages ou des albums.
1
2
Appuyez sur DVD DISPLAY.
Le menu de commande et le nom du disque
de données MP3 apparaissent.
5
Sélectionnez une plage à l’aide de X/x,
puis appuyez sur ENTER.
Appuyez sur X/x pour sélectionner
(ALBUM), puis appuyez sur
ENTER ou sur c.
La lecture de la plage sélectionnée
commence.
La liste des albums figurant sur le disque
apparaît.
Pour revenir à l’affichage
précédent
HOME TOWN
MP3
Appuyez sur O RETURN/EXIT ou C.
ROCK BEST HIT
KARAOKE
JAZZ
Pour désactiver le menu de
commande
R&B
MY FAVORITE SONGS
CLASSICAL
SALSA OF CUBA
BOSSANOVA
Appuyez sur DVD DISPLAY.
Remarques
• Seuls les lettres de l’alphabet et les chiffres peuvent
être utilisés pour les noms d’album ou de plage. Tout
autre caractère est remplacé par « ».
• Si le fichier MP3 que vous lisez comporte une
étiquette ID3, ses informations sont affichées à la
place du nom de plage.
3
Sélectionnez l’album que vous
souhaitez écouter à l’aide de X/x, puis
appuyez sur ENTER.
• Les étiquettes ID3 s’appliquent uniquement à la
version 1.
• Lors de la lecture d’un fichier MP3 à débit variable
(VBR), le temps écoulé indiqué peut être différent du
temps réellement écoulé.
Conseil
Lorsqu’un disque de données MP3 est inséré, vous
pouvez sélectionner un album à l’aide des touches
ALBUM– ou ALBUM+ de la télécommande.
27FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Sélection d’un album et d’un
fichier
Lecturedesfichiersimage
JPEG
Vous pouvez lire des fichiers image JPEG à
partir de CD-ROM, CD-R ou CD-RW.
ALBUM–
ALBUM+
ENTER
C/X/x/c
Cependant, les disques doivent être enregistrés
conformément à la norme ISO9660 niveau 1,
niveau 2 ou au format Joliet pour que l’ampli-
tuner reconnaisse les fichiers. Vous pouvez
également lire des disques enregistrés en multi-
session. Reportez-vous aux instructions de
l’appareil CD-R/RW ou du logiciel
O RETURN/
EXIT
DVD
DISPLAY
d’enregistrement (non fourni) pour obtenir des
détails sur le format d’enregistrement.
1
2
Appuyez sur DVD DISPLAY.
1
2
Chargez dans l’ampli-tuner un disque
de données enregistré en JPEG.
Le menu de commande et le nom du disque
de données JPEG apparaissent.
Appuyez sur H.
Appuyez sur X/x pour sélectionner
(ALBUM), puis appuyez sur
ENTER ou sur c.
L’ampli-tuner commence à lire le premier
fichier image JPEG du premier album du
disque.
La liste des albums figurant sur le disque
apparaît.
Remarques
• L’ampli-tuner peut également lire des fichiers portant
l’extension « .JPG » ou « .JPEG ».
MOUNTAIN
JPEG
FAMILY
FLOWER
GARDEN
TRAIN
• L’ampli-tuner peut lire les CD multi-session.
• Nombre maximal d’albums par disque : 99
(Un album ne peut pas contenir plus de 250 fichiers
image JPEG.)
CAR
• Un album dépourvu de fichier JPEG est ignoré.
• Si l’ampli-tuner ne peut pas lire une fichier JPEG,
retirez le disque et sélectionnez « REGLAGE
PERSONNALISE » parmi les paramètres de
configuration. Sélectionnez ensuite « PRIORITE CD
DONNEES » et choisissez « JPEG » (page 73) avant
de réinsérer le disque.
3
4
Sélectionnez l’album que vous
souhaitez écouter à l’aide de X/x, puis
appuyez sur ENTER.
Sélectionnez
(FICHIER) à
• Il n’est pas possible de lire un fichier image JPEG
d’une longueur ou d’une largeur supérieure à
4 720 points.
l’aide de X/x, puis appuyez sur ENTER.
La liste des fichiers figurant sur l’album en
cours apparaît.
• Certains CD-R ou CD-RW ne peuvent pas être lus sur
cet ampli-tuner, en raison de leur format de fichier.
• L’ampli-tuner peut lire jusqu’à une profondeur de 8
répertoires.
MOUNTAIN
FAMILY
JPEG
1.HAPPY
2.BIRTHDAY
3.CELEBRATION
4.CHRISTMAS
5.MOM
6.BASEBALL
7.PARTY
8.DAD
• Impossible de lire les fichiers image JPEG
progressifs sur cet ampli-tuner.
9.TRAVEL
10.FRIEND
11.DRIVE
28FR
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Appuyez sur M alors qu’une image
JPEG est affichée.
Lorsque la liste de tous les fichiers ou
albums ne peut pas être affichée, la barre de
défilement apparaît. Appuyez sur c pour
sélectionner l’icône de la barre de
défilement, puis déplacez-la pour afficher
le reste de la liste à l’aide de X/x. Appuyez
sur C ou O RETURN/EXIT pour revenir
à la liste des fichiers ou des albums.
Le diaporama démarre à partir de l’image
en cours.
Appuyez sur H pour quitter le
diaporama.
Revenez au mode normal à partir de
l’image en cours.
5
Sélectionnez un fichier à l’aide de X/x,
puis appuyez sur ENTER.
Pour modifier le minutage du
diaporama
Chaque fois que vous appuyez sur M en cours
de diaporama, vous modifiez son minutage.
L’affichage est modifié comme suit à chaque
pression de la touche :
La lecture du fichier sélectionné
commence.
Pour revenir à l’affichage
précédent
Appuyez sur O RETURN/EXIT ou C.
AV1M t AV2M t AV3M
Pour désactiver le menu de
commande
Le minutage AV3M est plus rapide que
AV2M.
Appuyez sur DVD DISPLAY.
Remarque
Remarque
Le diaporama ne peut être lu que dans un seul sens.
Seuls les lettres de l’alphabet et les chiffres peuvent
être utilisés pour les noms d’album ou de fichier. Tout
autre caractère est remplacé par « ».
Pour faire pivoter l’image en
cours
Conseil
Lorsqu’un disque de données JPEG est inséré, vous
pouvez sélectionner un album à l’aide des touches
ALBUM– ou ALBUM+ de la télécommande.
Diaporama à partir d’un
disque de données JPEG
H
C/c
M
H
suite
29FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Faites pivoter l’image en cours à l’aide de
C/c
Création de votre propre
programme
A chaque pression de c, l’image tourne de 90°
dans le sens des aiguilles d’une montre.
A chaque pression de C, l’image tourne de 90º
dans le sens contraire des aiguilles d’une
montre.
(Lecture programmée)
Remarque
Vous pouvez lire le contenu d’un disque dans
l’ordre de votre choix en organisant les plages
du disque comme bon vous semble pour créer
votre propre programme. Vous pouvez
programmer jusqu’à 25 pas.
Vous ne pouvez pas faire pivoter une image au cours
d’un diaporama. Appuyez sur H pour revenir en
mode de lecture normale.
PLAY
MODE
REPEAT
Touches
numériques
CLEAR
H
ENTER
C/X/x/c
O RETURN/
EXIT
1
En mode d’arrêt, appuyez plusieurs
fois sur PLAY MODE jusqu’à ce que
l’indication « PROGRAM » apparaisse
dans la fenêtre d’affichage du panneau
frontal.
Le menu du programme s’affiche sur
l’écran du téléviseur.
Program
Total Time 0:00
1
2
3
4
5
6
7
8
9
10
30FR
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Appuyez sur c.
5
6
Pour programmer d’autres plages,
répétez les étapes 2 à 4.
Le curseur se déplace jusqu’à la plage (dans
ce cas, « 1 »). Avant de programmer les
plages MP3, vous devez sélectionner
l’album.
Les plages programmées sont affichées
dans l’ordre sélectionné.
Appuyez sur H pour démarrer la
lecture programmée.
Program
Total Time 0:00
1
2
Track
1
2
3
4
5
6
7
8
9
TRACK1
TRACK2
TRACK3
TRACK4
TRACK5
TRACK6
TRACK7
TRACK8
TRACK9
La lecture programmée commence.
Lorsque le programme est terminé, vous
pouvez le réécouter en appuyant sur H.
3
4
5
6
7
8
9
10
10 TRACK10
Fonctions complémentaires
Pour
Vous devez
Lorsque la liste de toutes les plages ne peut
pas être affichée, la barre de défilement
apparaît. Appuyez sur c pour sélectionner
l’icône de la barre de défilement, puis
déplacez-la pour afficher le reste de la liste
à l’aide de X/x. Appuyez sur C ou O
RETURN/EXIT pour revenir à la liste des
plages.
Revenir à la
lecture normale cours de lecture.
Appuyer sur la touche CLEAR en
Désactiver le
menu de
programmes
Appuyer sur PLAY MODE en
mode d’arrêt pour désactiver le
menu de programmes.
Annuler l’ordre Appuyer sur CLEAR pendant que
programmé
la fenêtre de programme est
affichée et que le dernier
programme est annulé.
3
4
Sélectionnez la plage que vous
souhaitez programmer.
Remarques
Par exemple, sélectionnez la plage « 7 ».
• La fonction de lecture programmée n’est pas
disponible pour les DVD et les JPEG.
• Lorsque vous programmez des plages MP3, « --:-- »
s’affiche comme durée totale des plages
programmées.
Program
Total Time 0:00
1
2
Track
1
2
3
4
5
6
7
8
9
TRACK1
TRACK2
TRACK3
TRACK4
TRACK5
TRACK6
TRACK7
TRACK8
TRACK9
3
4
5
6
• Lorsque vous retirez le disque, la lecture programmée
est annulée et le programme que vous avez créé est
effacé.
7
8
9
10
10 TRACK10
Conseil
Vous pouvez effectuer une lecture répétée des plages
programmées. Appuyez sur REPEAT ou réglez
« REPETEE » sur « TOUS » dans la fenêtre du menu
de commande en cours de lecture programmée
Appuyez sur X/x ou sur les touches
numériques pour sélectionner « 7 »,
puis appuyez sur ENTER.
Durée totale des plages programmées
(à l’exception des fichiers MP3)
Program
1
2
3
4
Total Time 12:34
TRACK7
5
6
7
8
9
10
31FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Réglage du mode aléatoire
dans le menu de commande
Lecture dans un ordre
aléatoire
Vous pouvez sélectionner soit la lecture
aléatoire normale, soit la lecture aléatoire de
l’album (MP3 uniquement).
(Lecture aléatoire)
L’ampli-tuner peut sélectionner des plages et les
lire de façon aléatoire. Des lectures aléatoires
successives engendrent un ordre de lecture
différent.
H
ENTER
X/x
DVD
DISPLAY
PLAY
MODE
CLEAR
1
2
Appuyez sur DVD DISPLAY.
H
Le menu de commande apparaît.
Appuyez sur X/x pour sélectionner
(MODE DE LECTURE), puis
appuyez sur ENTER.
HOME TOWN
MP3
8 ALBUM
:
1
2
En mode d’arrêt, appuyez plusieurs
fois sur PLAY MODE jusqu’à ce que
l’indication « SHUFFLE » apparaisse
dans la fenêtre d’affichage du panneau
frontal.
LECTURE CONTINUE
LECTURE CONTINUE(ALBUM)
ALEATOIRE
ALEATOIRE(ALBUM)
PROGRAMMEE
Lors de la lecture d’un disque MP3, vous
pouvez lire toutes les plages des albums
dans un ordre aléatoire.
3
4
Sélectionnez ALEATOIRE ou
ALEATOIRE (ALBUM) à l’aide de X/x,
puis appuyez sur ENTER.
Pour plus de détails sur la lecture aléatoire
ALEATOIRE : Lit les plages du disque
dans un ordre aléatoire.
ALEATOIRE (ALBUM) : Lit les plages de
l’album sélectionné dans un ordre aléatoire.
Appuyez sur H.
Pour revenir à la lecture normale
Appuyez sur H.
En mode d’arrêt, appuyez trois fois sur PLAY
MODE pour annuler ALEATOIRE ou deux fois
pour annuler ALEATOIRE (ALBUM). Vous
pouvez également appuyer sur CLEAR pendant
la lecture pour revenir en lecture normale.
La lecture aléatoire sélectionnée
commence.
32FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Remarque
La lecture aléatoire est annulée lorsque vous éjectez le
disque. Le mode de lecture change dans l’ordre
suivant :
Lecture répétée
(Lecture répétée)
ALEATOIRE t LECTURE CONTINUE
ALEATOIRE (ALBUM) t LECTURE
CONTINUE (ALBUM)
Vous pouvez lire tous les titres/plages/fichiers
ou un seul titre/chapitre/plage/album d’un
disque.
En mode de lecture aléatoire ou programmée,
l’ampli-tuner répète les plages dans un ordre
aléatoire ou programmé.
Vous ne pouvez pas effectuer de lecture répétée
en cours de lecture PBC de CD VIDEO
REPEAT
CLEAR
H
ENTER
X/x
DVD
DISPLAY
1
2
Appuyez sur DVD DISPLAY.
Le menu de commande apparaît.
Appuyez sur X/x pour sélectionner
(REPETEE), puis appuyez
sur ENTER.
Si vous ne sélectionnez pas « NON », le
témoin « REPETEE » s’allume en vert.
3
Sélectionnez le réglage de la lecture
répétée, puis appuyez sur ENTER.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
T
1 : 3 2 : 5 5
NON
TOUS
TITRE
CHAPITRE
suite
33FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Vous pouvez rapidement afficher le statut
« REPETEE ». Appuyez sur la touche REPEAT de la
télécommande.
x Lors de la lecture d’un DVD
• NON : ne lit pas le disque de façon
répétée.
• Vous pouvez utiliser la lecture répétée pour les titres
DVD contenant des chapitres.
• TOUS : répète tous les titres.
• TITRE : répète le titre en cours sur un
disque.
• CHAPITRE : répète le chapitre en
cours.
x Lors de la lecture d’un CD VIDEO/
Super Audio CD/CD/MP3 avec la
lecture programmée réglée sur NON
• NON : ne lit pas le disque de façon
répétée.
• TOUS : répète toutes les plages du
disque ou l’album en cours de lecture
(uniquement si LECTURE
CONTINUE (ALBUM) ou
ALEATOIRE (ALBUM) est
sélectionné en mode de lecture).
• PLAGE : répète la plage en cours.
x Lors de la lecture d’un JPEG
• NON : ne lit pas le disque de façon
répétée.
• TOUS : répète tous les fichiers du
disque (si LECTURE CONTINUE est
sélectionné en mode de lecture ) ou
répète l’album en cours de lecture (si
LECTURE CONTINUE (ALBUM)
est sélectionné en mode de lecture).
x Lorsque la lecture programmée est
réglée sur OUI
• NON : ne lit pas le disque de façon
répétée.
• TOUS : répète la lecture programmée.
Pour annuler la lecture répétée
Appuyez sur CLEAR.
Remarques
• Suivant les DVD, il se peut que la lecture répétée ne
fonctionne pas.
• La lecture répétée est annulée lorsque vous éjectez le
disque.
• Si « TOUS » est sélectionné, la lecture répétée est
limitée à 5 occurrences.
Conseils
• Vous pouvez activer la lecture répétée en mode
d’arrêt. Après avoir sélectionné le paramètre
« REPETEE », appuyez sur H. L’ampli-tuner
démarre la lecture répétée.
34FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Pour changer la vitesse de
balayage (DVD/CD VIDEO
uniquement)
Chaque fois que vous appuyez sur m ou M
en cours de balayage, la vitesse de lecture
change. Il existe deux vitesses. L’affichage est
modifié comme suit à chaque pression de la
touche :
Recherche d’un point
spécifique sur un disque
(Balayage, Lecture au ralenti)
Vous pouvez localiser rapidement un point
spécifique sur le disque en contrôlant l’image ou
en effectuant une lecture au ralenti.
Sens de lecture
AV1M t AV2M
Sens inverse
RET1m t RET2m
La vitesse de lecture AV2M/RET2m est
supérieure à AV1M/RET1m.
m/M
y
/y
Visualisationimageparimage
(lecture au ralenti)
(DVD/CD VIDEO uniquement)
y
H
Appuyez sur
ou y lorsque l’ampli-tuner
est en mode de pause.
Pour revenir à la vitesse normale, appuyez sur
H.
Remarques
• Suivant les DVD/CD VIDEO, il se peut que vous ne
puissiez pas réaliser certaines des opérations décrites.
• Le balayage ou la lecture au ralenti ne
s’accompagnent d’aucun son.
Pour changer la vitesse de
lecture au ralenti
y
Chaque fois que vous appuyez sur
ou y en
cours de lecture au ralenti, la vitesse de lecture
change. Il existe deux vitesses. L’affichage est
modifié comme suit à chaque pression de la
touche :
Localisation rapide d’un point
en lisant un disque en avance
rapide ou en retour rapide
(balayage)
Sens de lecture
LENT 2y t LENT 1y
1
Appuyez sur m ou M en cours de
lecture d’un disque.
Sens inverse (DVD uniquement)
LENT 2 t LENT 1
y
y
2
Lorsque vous avez trouvé le point
souhaité, appuyez sur H pour revenir
à la vitesse normale.
y
La vitesse de lecture LENT 2y/LENT 2 est
y
inférieure à LENT 1y/LENT 1
.
35FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x Lors de la lecture d’un DVD
Recherche d’un titre/
chapitre/plage/index/
album/fichier
(TITRE)
x Lors de la lecture d’un CD VIDEO
(PLAGE)
x Lors de la lecture d’un Super Audio
CD
(PLAGE)
Vous pouvez rechercher un titre (DVD), un
chapitre (DVD), une plage (CD, CD VIDEO,
Super Audio CD, MP3), un index (CD VIDEO,
Super Audio CD) et un album (MP3, JPEG) et
un fichier (JPEG). Etant donné que les titres, les
plages, les albums et les fichiers ont des noms
uniques sur le disque, vous pouvez sélectionner
celui de votre choix à partir du menu de
commande. Les chapitres et les index ont
également des noms uniques sur le disque, vous
pouvez ainsi les sélectionner en saisissant leurs
numéros. Vous pouvez également rechercher un
point donné en utilisant le code temporel
(RECH. TEMPORELLE).
x Lors de la lecture d’un CD
(PLAGE)
x Lors de la lecture d’un MP3
(ALBUM) ou
(PLAGE)
x Lors de l’affichage d’un fichier JPEG
(ALBUM) ou
(FICHIER)
Exemple : Si vous sélectionnez
(PLAGE)
La liste des plages du disque apparaît.
GREATEST HITS
CD
1.HIGHWAY
2.VIEW POINT
3.MY CHILDREN
4.DANCING
5.GOOD TASTE
6.DESTINATION
7.MARATHON
8.PLACE-KICK
9.TAKE IT EASY
10.PORT TOWER
11.STANDARD
12.LADY
Touches
numériques
CLEAR
Lorsque la liste de toutes les plages ne peut
pas être affichée, la barre de défilement
apparaît. Appuyez sur c pour sélectionner
l’icône de la barre de défilement, puis
déplacez-la pour afficher le reste de la liste
à l’aide de X/x. Appuyez sur C ou O
RETURN/EXIT pour revenir à la liste des
plages.
ENTER
C/X/x/c
O RETURN/
EXIT
DVD
DISPLAY
GREATEST HITS
CD
13.STAY
14.BAD
15.BEAUTIFUL
16.HOLD.ME
17.FIRST TIME
18.BLUE SKY
19.OUR EARTH
20.NO NAME
21.SWEETEST
22.KISS ME
23.FIRE
Recherche d’un titre/plage/
album/fichier
1
Appuyez sur DVD DISPLAY.
Le menu de commande apparaît.
24.ANGEL
2
Appuyez sur X/x pour sélectionner la
méthode de recherche, puis appuyez
sur ENTER.
36FR
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Appuyez sur X/x pour sélectionner la
plage souhaitée, puis appuyez sur
ENTER.
4
5
Appuyez sur X/x ou sur les touches
numériques pour sélectionner le
numéro de chapitre ou d’index que
vous souhaitez rechercher.
L’ampli-tuner commence la lecture à partir
de la plage sélectionnée.
Si vous faites une erreur
Annulez le numéro en appuyant sur
CLEAR, puis sélectionnez un autre
numéro.
Recherche d’un chapitre/
index
1
Appuyez sur ENTER.
Appuyez sur DVD DISPLAY.
L’ampli-tuner commence la lecture à partir
du numéro sélectionné.
Le menu de commande apparaît.
2
Appuyez sur X/x pour sélectionner la
méthode de recherche.
Pour désactiver le menu de
commande
Appuyez plusieurs fois sur DVD DISPLAY
jusqu’à ce que le menu de commande
disparaisse.
x Lors de la lecture d’un DVD
(CHAPITRE)
x Lors de la lecture d’un CD VIDEO
(INDEX)
Pour rechercher un point donné à
l’aide du code temporel (RECH.
TEMPORELLE)
Exemple : Si vous recherchez le temps de
lecture du titre en cours sur un DVD.
x Lors de la lecture d’un Super Audio
CD
(INDEX)
Exemple : Si vous sélectionnez
(CHAPITRE)
« ** (**) » est sélectionné (** est un
numéro).
1 A l’étape 2, sélectionnez
(TEMPS).
« T **:**:** » (temps de lecture du titre en
cours) est sélectionné.
Les nombres entre parenthèses indiquent le
nombre total de titres, chapitres, plages ou
index.
2 Appuyez sur ENTER.
« T--:--:-- » apparaît au-dessus de
« T**:**:** ».
DVD
DVD
3 Entrez le code temporel à l’aide des touches
numériques, puis appuyez sur ENTER.
Par exemple, pour trouver le point de votre
choix 2 heures, 10 minutes et 20 secondes
après le début, vous n’avez qu’à saisir
« 2:10:20 ».
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
T
Remarques
• Le numéro de titre, de chapitre ou de plage affiché sur
l’écran du téléviseur provient des données
enregistrées sur le disque.
3
Appuyez sur ENTER.
« ** (**) » est remplacé par « -- (**) ».
• Il est impossible de rechercher une scène d’un CD
VIDEO.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
– – 3 4
1 : 3 2 : 5 5
• Si vous lisez un DVD, saisissez le temps de lecture du
titre en cours à l’aide du code temporel. Si vous lisez
un CD, un Super Audio CD, un CD VIDEO ou un
MP3, entrez le temps de lecture de la plage en cours
à l’aide du code temporel.
T
suite
37FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Conseil
Vous pouvez adapter l’affichage pour qu’il indique le
temps de lecture ou la durée restante. Pour plus de
détails, reportez-vous à la section « Vérification du
temps de lecture et de la durée restante dans le menu de
Visualisation des
informations relatives au
disque
Visualisation du temps de
lecture et de la durée restante
dans la fenêtre d’affichage du
panneau frontal
Vous pouvez vérifier les informations de disque,
notamment le temps restant, le nombre total de
titres d’un DVD ou de plages d’un Super Audio
CD, CD, CD VIDEO ou MP3, à l’aide de la
fenêtre d’affichage du panneau frontal
DISPLAY/
JUMP
Appuyez sur DISPLAY/JUMP.
Chaque fois que vous appuyez sur DISPLAY/
JUMP pendant la lecture du disque, l’affichage
change comme indiqué dans les tableaux.
38FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Lors de la lecture d’un DVD
Temps de lecture et numéro du titre en cours
Lors de la lecture d’un CD VIDEO
(sans fonction PBC), d’un Super
Audio CD ou d’un CD
Temps de lecture et numéro de la plage en cours
(Lors de la lecture d’un CD)
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Durée restante du titre
en cours
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Durée restante de la
plage en cours
Temps de lecture et
numéro du chapitre en
cours
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Temps de lecture du
disque
Durée restante du
chapitre en cours
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Durée restante du
disque
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
Titre*
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
ALL 1DISCS
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Nom de la plage*
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
suite
39FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Dans le cas suivant, il est possible que le temps de
lecture écoulé et la durée restante sur la plage ne
s’affichent pas correctement.
Lors de la lecture d’un MP3
Temps de lecture et numéro de la plage en cours
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
– lors de la lecture d’un fichier MP3 à débit variable
(VBR).
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Durée restante de la
plage en cours
Conseils
• Seul le temps de lecture apparaît lorsque vous lisez
des CD VIDEO dotés de fonctions PBC.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
• Le temps de lecture et la durée restante du chapitre,
du titre, de la plage, de la scène ou du disque en cours
apparaissent également sur votre écran de téléviseur.
Reportez-vous à la section suivante, « Vérification du
temps de lecture et de la durée restante », pour savoir
comment interpréter ces informations.
Nom de la plage
(fichier)
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Nom de l’album
(dossier)
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Lors de la lecture d’un JPEG
Numéro du fichier en cours
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Nom du fichier
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Nom de l’album
(dossier)
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
* « NO TEXT » apparaît s’il n’existe pas
d’informations sur le nom.
Remarques
• Selon le type de disque en cours de lecture et le mode
de lecture, les informations relatives au disque
peuvent ne pas s’afficher.
• Les étiquettes ID3 s’appliquent uniquement à la
version 1.
• Si le fichier MP3 que vous lisez comporte des
informations ID3, celles-ci sont affichées comme un
nom de plage.
• Seuls les chiffres et les lettres de l’alphabet peuvent
être utilisés pour les noms d’album ou de plage. Tout
autre caractère est remplacé par « ».
40FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x Lors de la lecture d’un DVD
• T **:**:**
Vérification du temps de
lecture et de la durée restante
dans le menu de commande
Temps de lecture du titre en cours
• T–**:**:**
Durée restante du titre en cours
• C **:**:**
Temps de lecture du chapitre en cours
• C–**:**:**
Durée restante du chapitre en cours
• **:**:**
Vous pouvez vérifier le temps de lecture et la
durée restante du titre, du chapitre ou de la plage
en cours, ainsi que le temps de lecture total ou la
durée restante du disque. Vous pouvez
également vérifier le texte du DVD/CD/Super
Audio CD et le nom du dossier MP3/fichier
MP3/étiquette ID3 (titre de chanson
Temps de lecture du menu ou du titre
en cours sans chapitre
uniquement) enregistré sur le disque.
x Lors de la lecture d’un CD VIDEO
(doté de fonctions PBC)
• **:**
Temps de lecture de la scène en cours
x Lors de la lecture d’un CD VIDEO
(sans fonction PBC), d’un Super Audio
CD ou d’un CD
DISPLAY/
JUMP
• T **:**
Temps de lecture de la plage en cours
• T–**:**
Durée restante de la plage en cours
• D **:**
Temps de lecture du disque en cours
• D–**:**
DVD
DISPLAY
Durée restante du disque en cours
x Lors de la lecture d’un MP3
• T **:**
1
2
Appuyez sur DVD DISPLAY en cours
de lecture.
Temps de lecture de la plage en cours
• T–**:**
Durée restante de la plage en cours
Le menu de commande apparaît.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
Pour désactiver le menu de
commande
Appuyez plusieurs fois sur DVD DISPLAY
jusqu’à ce que le menu de commande
disparaisse.
(
)
1 8 3 4
1 : 3 2 : 5 5
T
Type de
disque
Informations
temporelles
Remarques
• Seules les lettres de l’alphabet et les chiffres peuvent
être affichés.
Appuyez plusieurs fois sur DISPLAY/
JUMP pour modifier les informations
temporelles.
• Selon le type de disque lu, l’ampli-tuner ne peut
afficher qu’un nombre limité de caractères. En outre,
suivant le disque, certains caractères du texte
n’apparaissent pas.
L’affichage et le type d’informations
temporelles que vous vérifiez dépendent du
disque en cours de lecture.
suite
41FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Vérification des informations
relatives à la date (JPEG
uniquement)
Vous pouvez vérifier les informations relatives à
la date lorsque l’étiquette Exif* est enregistrée
dans les données d’image JPEG.
DVD
DISPLAY
Appuyez sur DVD DISPLAY en cours de
lecture.
Le menu de commande apparaît.
MOUNTAIN
JPEG
FAMILY
(
) BIRTHDAY
2 0
1
01 / 01 / 2003
Informations
relatives à la date
* Le format « Exchangeable Image File Format » est
un format d’image pour appareil photo numérique
défini par la Japan Electronics & Information
Technology Industries Association.
Remarque
Si les informations relatives à la date sont altérées ou
absentes du disque, l’ampli-tuner est dans
l’impossibilité de les afficher.
Conseil
Vous pouvez modifier les informations relatives à la
date dans DATE JPEG de REGLAGE
PERSONNALISE (page 74).
42FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Les options de AUDIO apparaissent.
DVD
DVD
Réglages du son
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
T
Commutation du son
1: ANGLAIS
2: FRANÇAIS
3: ESPAGNOL
Si le DVD est enregistré avec des plages
multilingues, vous pouvez sélectionner la
langue de votre choix en cours de lecture.
Si le DVD est enregistré selon plusieurs formats
audio (PCM, Dolby Digital, MPEG audio ou
DTS), vous pouvez sélectionner le format audio
de votre choix en cours de lecture.
Avec les CD stéréo, les CD VIDEO ou les
fichiers MP3, vous pouvez sélectionner le son
du canal gauche ou droit et écouter le son du
canal de votre choix simultanément via les
enceintes gauche et droite (l’effet stéréo est
toutefois perdu). Par exemple, sur un disque
comportant une chanson, avec la partie vocale
sur le canal droit et la partie instrumentale sur le
canal gauche, vous pouvez sélectionner le canal
gauche et écouter uniquement la partie
3
Appuyez sur X/x pour sélectionner le
signal audio souhaité.
x Lors de la lecture d’un DVD
Les langues que vous pouvez sélectionner
diffèrent suivant les DVD.
Lorsque 4 chiffres sont affichés, ils
représentent le code de langue. Reportez-
vous à la liste des codes de langue page 92
pour voir quelle langue le code représente.
Lorsque la même langue est affichée deux
fois ou davantage, le DVD est enregistré en
formats audio multiples.
x Lors de la lecture d’un CD VIDEO,
CD, ou MP3
Le réglage par défaut est souligné.
instrumentale via les deux enceintes.
• STEREO : Son stéréo standard
• 1/G : Son du canal gauche (mono)
• 2/D : Son du canal droit (mono)
x Lors de la lecture d’un Super Audio
CD
En mode d’arrêt, suivant le Super Audio
CD, le choix des réglages varie.
AUDIO
• MULTI : Le disque dispose d’une
zone de lecture multi-canaux.
• 2 CANAUX : Le disque dispose
d’une zone de lecture à 2 canaux.
• CD : Si vous souhaitez lire le disque
comme un CD classique.
ENTER
X/x
DVD
Remarque
Tous les disques ne vous donnent pas les trois
choix ci-dessus en lecture Super Audio CD. Tout
dépend de la configuration des couches du Super
Audio CD à lire.
DISPLAY
1
2
Appuyez sur DVD DISPLAY en cours
de lecture.
4
Appuyez sur ENTER.
Le menu de commande apparaît.
Appuyez sur X/x pour sélectionner
(AUDIO), puis appuyez sur
ENTER.
suite
43FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Pour désactiver le menu de
commande
Exemples d’affichage :
• PCM (stéréo)
Appuyez plusieurs fois sur DVD DISPLAY
jusqu’à ce que le menu de commande
disparaisse.
PROGRAM FORMAT
PCM 48kHz 24bit
• Dolby Surround
Remarques
• Il est impossible de commuter le son des disques qui
ne sont pas enregistrés selon plusieurs formats audio.
• En cours de lecture DVD, le son peut commuter
automatiquement.
PROGRAM FORMAT
DOLBY DIGITAL 2/0
DOLBY SURROUND
Conseil
• Dolby Digital 5.1 canaux
Vous pouvez directement sélectionner « AUDIO » en
appuyant sur la touche AUDIO. A chaque pression sur
cette touche, le paramètre change.
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
• DTS
Affichage des informations
audio relatives au disque
(DVD uniquement)
PROGRAM FORMAT
DTS 3/2.1
Conseils
Lorsque vous sélectionnez « AUDIO », les
canaux de lecture sont affichés sur l’écran.
Par exemple, en format Dolby Digital, plusieurs
signaux (allant d’un signal mono à un signal
5.1 canaux) peuvent avoir été enregistrés sur un
DVD. Suivant les DVD, le nombre de canaux
enregistrés peut différer.
• Lorsque le signal contient des composantes de
signaux surround, telles que LS, RS ou S, l’effet
surround est amélioré.
• Si vous lisez des plages MPEG AUDIO, l’ampli-
tuner restitue des signaux PCM (stéréo).
• Bien que le flux audio comporte une composante
arrière surround, le canal arrière surround n’est pas
affiché.
Format audio en cours*
La source Dolby Digital-EX ou DTS-ES apparaît
sous la forme « 3/2.1 » à l’écran
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
1: ANGLAIS
T
PROGRAM FORMAT
DOLBY DIGITAL 3/2.1
* L’indication « PCM », « MPEG », « DTS » ou
« DOLBY DIGITAL » apparaît.
Lorsque l’indication « DOLBY DIGITAL »
s’affiche, les canaux de la plage de lecture sont
représentés par des numéros comme suit :
Pour la composante sonore Dolby Digital
5.1 canaux :
Composante surround 2
DOLBY DIGITAL 3 / 2.1
Composante frontale 2 +
composante centrale 1
Composante LFE (effet
de basse fréquence) 1
44FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Appuyez plusieurs fois sur la touche A.F.D.
de la télécommande jusqu’à ce que
l’indication « A.F.D. AUTO » apparaisse
dans la fenêtre d’affichage du panneau
frontal.
Utilisation du son
ambiophonique
Champ acoustique
Affichage
Vous pouvez bénéficier du son ambiophonique
en sélectionnant simplement l’un des champs
acoustiques préprogrammés, en fonction du
programme que vous souhaitez écouter. Ils vous
permettent de découvrir chez vous l’acoustique
exaltante et puissante des salles de cinéma.
Pour sélectionner un champ acoustique,
AUTO FORMAT DIRECT
AUTO
A.F.D. AUTO
Utilisation des enceintes
avant uniquement
(2 CHANNEL STEREO)
appuyez plusieurs fois sur la touche A.F.D.,
2CH ou MODE de la télécommande jusqu’à ce
que le champ acoustique souhaité apparaisse
dans la fenêtre d’affichage du panneau frontal.
Ce mode émet le son des enceintes avant gauche
et droite. Les sources deux canaux (stéréo)
standard omettent complètement le traitement
du champ acoustique. Les formats
ambiophoniques multi-canaux sont remixés en 2
canaux.
Ceci permet de lire n’importe quelle source en
utilisant les enceintes avant gauche et droite.
Décodage automatique du
signal d’entrée audio (AUTO
FORMAT DIRECT AUTO)
La fonction de décodage automatique détecte le
type de signal audio entré (Dolby Digital, DTS
ou signal stéréo 2 canaux standard) et effectue le
décodage requis, le cas échéant. Ce mode
présente le son tel qu’il a été enregistré/encodé
sans lui ajouter d’effets (ex : réverbération).
Toutefois, en l’absence de signaux basse
2CH
fréquence (Dolby Digital LFE, etc.), il émet un
signal basse fréquence vers le caisson de graves.
A.F.D.
Appuyez sur la touche 2CH de la
télécommande.
« 2CH STEREO » apparaît dans la fenêtre
d’affichage du panneau frontal.
Champ acoustique
Affichage
2CHANNEL STEREO
2CH STEREO
suite
45FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x Neo:6 Cinema
Exécute le décodage en mode DTS Neo:6
Cinema.
Sélection d’un champ
acoustique (touche A.F.D.)
x Neo:6 Music
Exécute le décodage en mode DTS Neo:6
Music. C’est le réglage idéal pour les sources
stéréo standard, notamment les CD.
A.F.D.
Réglage avancé
Vous pouvez modifier la fréquence
d’échantillonnage en présence d’un signal
d’entrée DTS 96/24.
ENTER
X/x
Appuyez plusieurs fois sur la touche A.F.D.
de la télécommande jusqu’à ce que le
champ acoustique souhaité apparaisse
dans la fenêtre d’affichage du panneau
frontal.
AMP MENU
Champ acoustique
PRO LOGIC
Affichage
1
2
Appuyez sur AMP MENU.
PRO LOGIC
PLII MOVIE
PLII MUSIC
NEO:6 CIN
NEO:6 MUS
Réglez la fonction de la télécommande sur
DVD, puis appuyez sur AMP MENU.
PRO LOGIC II MOVIE
PRO LOGIC II MUSIC
Neo:6 Cinema
Appuyez plusieurs fois sur X/x jusqu’à
ce que « dts 96/24 » apparaisse dans la
fenêtre d’affichage du panneau frontal,
puis appuyez sur ENTER.
Neo:6 Music
x PRO LOGIC
Exécute un décodage Dolby Pro Logic. Une
source enregistrée sur 2 canaux est décodée en
4 canaux.
3
Appuyez sur X/x pour sélectionner
« 96/24 AUTO » puis appuyez sur
ENTER ou AMP MENU.
x PRO LOGIC II MOVIE
• AUTO : Un signal d’entrée DTS 96/24 est
relu à la fréquence d’échantillonnage de
96 kHz.
Exécute un décodage en mode Dolby Pro Logic
II Movie. C’est le réglage idéal pour les films
encodés en Dolby Surround. En outre, ce mode
peut reproduire le son en 5.1 canaux lorsque
vous regardez l’enregistrement vidéo de vieux
films ou de films doublés.
• NON : Même en présence d’un signal
d’entrée DTS 96/24, la lecture s’effectue à
la fréquence d’échantillonnage de 48 kHz.
Remarques
x PRO LOGIC II MUSIC
• Lorsque le signal d’entrée provient d’une source
multi-canaux, PRO LOGIC, PRO LOGIC II MOVIE/
MUSIC et Neo:6 Cinema/Music sont annulés et la
source multi-canaux est reproduite directement.
• Le mode de décodage Neo:6 Cinema/Music n’est pas
disponible pour le signal DTS 2 canaux.
Exécute un décodage en mode Dolby Pro Logic
II Music. C’est le réglage idéal pour les sources
stéréo standard, notamment les CD.
46FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• En cas de décodage au moyen de DTS 96/24 (à
l’exception du mode A.F.D.) dans le champ
acoustique, les signaux de sortie sont convertis en 48
kHz (fréquence d’échantillonnage).
Signal Processor) propre à Sony pour
développer le concept de « Digital Cinema
Sound ». Le « Digital Cinema Sound » simule
l’environnement sonore d’une salle de cinéma
idéale dans un installation de cinéma à domicile
en appliquant les préférences du réalisateur du
film.
• Dès qu’une enceinte est réglée sur « PETIT » ou que
le caisson de graves est réglé sur « NEANT » au
niveau du réglage des enceintes, les signaux de sortie
sont convertis en 48 kHz (fréquence
d’échantillonnage).
x C.ST.EX A (Cinema Studio EX A)
Reproduit les caractéristiques sonores du studio
de production cinématographique « Cary Grant
Theater » de Sony Pictures Entertainment. Il
s’agit d’un mode standard parfaitement adapté à
la plupart des types de films.
Sélection d’un champ
acoustique (touche MODE)
x C.ST.EX B (Cinema Studio EX B)
Reproduit les caractéristiques sonores du studio
de production cinématographique « Kim Novak
Theater » de Sony Pictures Entertainment. Il
s’agit du mode idéal pour regarder des films
d’action ou de science-fiction riches en effets
sonores.
MODE
x C.ST.EX C (Cinema Studio EX C)
Reproduit les caractéristiques sonores du studio
d’arrangement de Sony Pictures Entertainment.
C’est le mode idéal pour regarder des comédies
musicales ou des classiques à la bande son riche
en musique.
x V.M.DIM (VIRTUAL MULTI DIMENSION)*
Utilise une image sonore 3D pour créer, à partir
d’une seule paire d’enceintes surround, un
ensemble d’enceintes virtuelles positionnées en
hauteur par rapport à l’auditeur. Ce mode crée 5
ensembles d’enceintes virtuelles qui entourent
l’auditeur, avec un angle d’élévation d’environ
30°.
Appuyez plusieurs fois sur la touche MODE
de la télécommande jusqu’à ce que le
champ acoustique souhaité apparaisse
dans la fenêtre d’affichage du panneau
frontal.
POUR LES FILMS
* Champ acoustique « VIRTUEL » : Champ
acoustique constitué d’enceintes virtuelles.
Champ acoustique
Affichage
CINEMA STUDIO EX A
CINEMA STUDIO EX B
CINEMA STUDIO EX C
V.MULTI DIMENSION
C.ST.EX A*
C.ST.EX B*
C.ST.EX C*
V.M.DIM
A propos de Cinema Studio EX
Cinema Studio EX est idéal pour apprécier
les films au son encodé au format multi-canaux,
notamment les DVD Dolby Digital. Ce mode
reproduit les caractéristiques sonores des studios
Sony Pictures Entertainment.
* Utilise la technologie DCS
A propos de DCS (Digital Cinema
Sound)
Cinema Studio EX est constitué des trois
éléments suivants.
En collaboration avec Sony Pictures
Entertainment, Sony a mesuré l’environnement
sonore de ses studios et a intégré les résultats de
ces mesures à la technologie DSP (Digital
suite
47FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x HP. [2CH] (HEADPHONE 2CH)
• Multidimension virtuelle
Ce mode reproduit le son par les canaux (stéréo)
G/D standard du casque en omettant
complètement le traitement du champ
acoustique. Les formats ambiophoniques multi-
canaux sont remixés en 2 canaux.
Crée, à partir d’une seule paire d’enceintes
surround, 5 ensembles d’enceintes virtuelles
qui entourent l’auditeur.
• Concordance avec la profondeur d’écran
Dans une salle de cinéma, le son semble venir
de l’intérieur de l’image réfléchie sur l’écran.
Cet élément recrée cette sensation dans votre
séjour en déplaçant le son des enceintes avant
« dans » l’écran.
Pour désactiver l’effet surround
Appuyez plusieurs fois sur la touche A.F.D. de
la télécommande jusqu’à ce que l’indication
« A.F.D. AUTO » apparaisse dans la fenêtre
d’affichage du panneau frontal, ou appuyez sur
la touche 2CH de la télécommande pour afficher
« 2CH STEREO ».
• Réverbération de studio de cinéma
Reproduit les réverbéra3tions propres à une
salle de cinéma.
Cinema Studio EX est le mode intégré qui
applique les trois éléments simultanément.
Remarques
• Cette fonction n’est pas disponible lors de la lecture
des Super Audio CD.
Remarques
• L’effet engendré par les enceintes virtuelles peut
entraîner l’augmentation du bruit dans le signal de
lecture.
• Lors de la lecture d’un Super Audio CD (Direct
Stream Digital), « AUTO FORMAT DIRECT
AUTO » est automatiquement sélectionné comme
champ acoustique.
• Lors de l’écoute avec des champs acoustiques qui
emploient les enceintes virtuelles, vous n’entendez
aucun son provenant directement des enceintes
surround.
• 2CH, A.F.D. et MODE ne sont pas accessibles pour
les sources PCM 96 kHz.
Conseils
POUR LA MUSIQUE
• Si vous souhaitez reproduire le son du téléviseur ou le
son stéréo d’une source à 2 canaux par l’intermédiaire
des 7 enceintes, sélectionnez un champ acoustique
autre que « AUTO FORMAT DIRECT AUTO » ou
« 2 CH STEREO ».
Champ acoustique
HALL
Affichage
HALL
JAZZ CLUB
JAZZ CLUB
L.CONCERT
• Chaque fois que vous sélectionnez une fonction telle
que DVD ou TUNER, le dernier champ acoustique
appliqué à la fonction est automatiquement
réappliqué. Si, par exemple, vous écoutez un DVD
avec le champ acoustique HALL, passez à une autre
fonction, puis revenez au DVD, HALL est de
nouveau appliqué. Au niveau du tuner, les champs
acoustiques sont mémorisés séparément pour
chacune des stations présélectionnées.
LIVE CONCERT
x HALL
Restitue l’acoustique d’une salle de concert
rectangulaire.
x JAZZ CLUB
Restitue l’acoustique d’un club de jazz.
x L. CONCERT (Concert en public)
Restitue l’acoustique d’un concert en public de
300 places.
• Vous pouvez connaître le format d’encodage des
disques en examinant leur emballage.
– Les disques Dolby Digital portent le logo
– Les programmes encodés en DTS-ES ou DTS 96/
24 sont désignés par l’indication DTS-ES ou DTS
96/24.
.
En cas d’utilisation du casque
Champ acoustique
HEADPHONE THEATER
HEADPHONE 2CH
Affichage
– Les disques Dolby Surround portent le logo
.
HP.THEATER
HP.[2CH]
– Les disques DTS Digital Surround portent la
mention DTS.
x HP. THEATER (HEADPHONE THEATER)
Ce mode est très efficace avec les sources de
signaux discrets 5.1 canaux, notamment Dolby
Digital et DTS.
48FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Flux d’entrée Canal de Décodeur arrière
Sélection du mode de
décodage Surround Back
sortie
surround appliqué
Dolby Digital 5.1
—
5.1
DTS 5.1
5.1
—
Dolby Digital 6.1
EX
Le décodeur Matrix est
conforme à la norme
Dolby Digital EX.
b)
Cette fonction vous permet de sélectionner le
mode de décodage des signaux arrière surround
du flux d’entrée multi-canaux.
En décodant le signal arrière surround du
logiciel DVD, par exemple, enregistré au format
Dolby Digital EX, DTS-ES Matrix, DTS-ES
Discrete 6.1, etc. vous pouvez bénéficier du son
surround initialement enregistré pour le film
DTS-ESMatrix 6.1
6.1
Décodeur DTS Matrix
c)
DTS-ES
Discrete 6.1
6.1
Décodeur DTS Discrete
d)
En cas de sélection de « SB
MATRIX »
Dolby Digital EX est appliqué pour décoder le
signal arrière surround quel que soit l’indicateur
a)
de décodage 6.1 canaux du flux d’entrée. Ce
décodeur est conforme à la norme Dolby Digital
e)
EX et fonctionne comme les décodeurs utilisés
dans les cinémas.
ENTER
X/x
Flux d’entrée Canal de Décodeur arrière
sortie
surround appliqué
Dolby Digital 6.1
5.1
Le décodeur Matrix est
conforme à la norme
Dolby Digital EX.
AMP MENU
DTS 5.1
6.1
Le décodeur Matrix est
conforme à la norme
Dolby Digital EX.
Dolby Digital 6.1
EX
Le décodeur Matrix est
conforme à la norme
Dolby Digital EX.
1
2
Appuyez sur AMP MENU.
b)
Réglez la fonction de la télécommande sur
DVD, puis appuyez sur AMP MENU.
DTS-ESMatrix 6.1
Le décodeur Matrix est
conforme à la norme
Dolby Digital EX.
c)
6.1
Appuyez plusieurs fois sur X/x jusqu’à
ce que « SurrB DEC. » apparaisse dans
la fenêtre d’affichage du panneau
frontal, puis appuyez sur ENTER.
DTS-ES
Discrete 6.1
6.1
Le décodeur Matrix est
conforme à la norme
Dolby Digital EX.
d)
3
Appuyez sur X/x pour sélectionner le
mode arrière surround de votre choix,
en fonction du flux d’entrée, puis
appuyez sur ENTER ou AMP MENU.
En cas de sélection de « SB
OFF »
Aucun décodage arrière surround n’est effectué.
Le réglage par défaut est « SB AUTO ».
a) L’indicateur de décodage 6.1 canaux correspond
aux informations enregistrées dans le logiciel,
notamment les DVD.
En cas de sélection de « SB
AUTO »
Lorsque le flux d’entrée contient l’indicateur de
décodage 6.1 canaux , le décodeur approprié
est appliqué afin de décoder le signal arrière
surround.
b) DVD Dolby Digital comportant un indicateur
Surround EX. Consultez l’aide de la page Web de
Dolby Corporation pour plus d’informations sur les
films Surround EX.
a)
suite
49FR
Download from Www.Somanuals.com. All Manuals Search And Download.
c) Logiciel encodé avec un indicateur qui signale qu’il
possède à la fois les signaux Surround EX et 5.1
canaux.
Sélection du décodage
prioritaire
d) Logiciel encodé avec les signaux 5.1 canaux et un
flux d’extension conçu pour renvoyer ces signaux
aux 6.1 canaux discrets. Les signaux 6.1 canaux
discrets sont des signaux propres aux DVD qui ne
sont pas utilisés dans les cinémas.
Cette fonction vous permet de sélectionner un
décodage prioritaire lorsque des signaux
numériques sont présents au niveau de la prise
d’entrée DIGITAL IN (OPTICAL IN/
e) Le décodeur peut être utilisé pour tous les formats
6.1 (Dolby Digital EX, DTS-ES Matrix 6.1 et DTS-
ES Discrete 6.1).
Remarques
COAXIAL IN), ou sont traités en mode DVD.
• Vous ne pouvez sélectionner le décodage arrière
surround que si le mode A.F.D. est sélectionné
(page 46). Dans d’autres champs acoustiques, cette
fonction est ignorée en interne.
• Certains disques ne possèdent pas d’indicateur Dolby
Digital EX, même si le logo Dolby Digital Surround
EX figure éventuellement sur leur emballage. En
pareil cas, sélectionnez « SB MATRIX ».
ENTER
X/x
AMP MENU
1
2
Appuyez sur AMP MENU.
Réglez la fonction de la télécommande sur
DVD, puis appuyez sur AMP MENU.
Appuyez plusieurs fois sur X/x jusqu’à
ce que « DEC. PRI. » apparaisse dans
la fenêtre d’affichage du panneau
frontal, puis appuyez sur ENTER.
3
Appuyez sur X/x pour sélectionner le
décodage prioritaire souhaité, puis
appuyez sur ENTER ou AMP MENU.
Le réglage par défaut est « PCM ».
En cas de sélection de « PCM »
Les signaux PCM sont prioritaires (pour éviter
toute interruption au moment du démarrage de la
lecture). Le son est reproduit, même en présence
d’autres signaux d’entrée. Toutefois, la
reproduction de signaux DTS-CD ne
s’accompagne d’aucun son ou bruit. En pareil
cas, sélectionnez « AUTO ».
50FR
Download from Www.Somanuals.com. All Manuals Search And Download.
En cas de sélection de « AUTO »
Modification de la valeur
d’impédance des
enceintes
La méthode de décodage la mieux adaptée est
automatiquement sélectionnée parmi les
méthodes DTS, Dolby Digital et PCM.
Toutefois, aucun son n’est initialement
reproduit au moment où commence la lecture de
signaux PCM.
Vous pouvez modifier la valeur d’impédance en
fonction de l’impédance de vos enceintes.
Les réglages par défaut sont soulignés.
Conseil
Tant que le mode DVD est sélectionné, vous pouvez
lire les signaux DTS-CD même si « PCM » est
sélectionné.
ENTER
X/x
AMP MENU
1
2
Appuyez sur AMP MENU.
Réglez la fonction de la télécommande sur
DVD, puis appuyez sur AMP MENU.
Appuyez plusieurs fois sur X/x jusqu’à
ce que « SP. IMP. (Ω) » apparaisse dans
la fenêtre d’affichage du panneau
frontal, puis appuyez sur ENTER.
3
Appuyez sur X/x pour sélectionner
« SP 4Ω/6Ω » ou « SP 8Ω » en fonction
de l’impédance, puis appuyez sur
ENTER ou AMP MENU.
SP 8Ω
Sélectionnez cette option si
l’impédance des enceintes est
égale ou supérieure à 8 ohms.
SP 4Ω/6Ω
Sélectionnez cette option si
l’impédance des enceintes est
inférieure à 8 ohms.
Remarques
• Utilisez des enceintes haute impédance.
• Choisissez des enceintes de taille adéquate présentant
des performances homogènes pour les canaux avant,
central, surround et arrière surround.
suite
51FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Impédance des enceintes
Pour profiter du meilleur son surround multi-
canaux possible, raccordez des enceintes d’une
impédance nominale égale ou supérieure à 8
ohms aux bornes FRONT, CENTER,
SURROUND et SURROUND BACK, et réglez
la valeur sur « SP 8Ω ». Reportez-vous au mode
d’emploi joint aux enceintes si vous n’êtes pas
sûr de leur impédance. (Ces renseignements
figurent souvent à l’arrière des enceintes.) En
outre, des enceintes dont l’impédance nominale
se situe entre 4 et 8 ohms peuvent aussi être
raccordées à n’importe quelles bornes pour
enceinte. Dans ce cas, veillez à régler la valeur
sur « SP 4Ω/6Ω », même si vous ne raccordez
qu’une seule enceinte dont l’impédance
nominale est comprise entre 4 et 8 ohms.
52FR
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
Utilisation de diverses fonctions
complémentaires
(
)
1 8 3 4
T
1
1 : 3 2 : 5 5
(
)
9
Commutation des angles
3
4
Appuyez sur ENTER
Si plusieurs angles d’une scène sont enregistrés
sur un DVD, vous pouvez modifier l’angle
d’observation.
Par exemple, dans une scène de train en marche,
vous pouvez afficher la vue observée depuis
l’avant du train, de la fenêtre gauche du train ou
de la fenêtre droite, sans que le mouvement du
train soit interrompu.
L’indication du numéro d’angle est
remplacée par « - ».
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
T
–
1 : 3 2 : 5 5
(
)
9
Sélectionnez le numéro d’angle à l’aide
des touches numériques ou de la
touche X/x, puis appuyez sur ENTER.
Touches
ANGLE
L’angle sélectionné est commuté.
numériques
Pour désactiver le menu de
commande
Appuyez plusieurs fois sur DVD DISPLAY
jusqu’à ce que le menu de commande
disparaisse.
ENTER
X/x
DVD
Remarque
Suivant les DVD, il se peut que vous ne puissiez pas
commuter les angles, même si plusieurs angles sont
enregistrés sur le DVD.
DISPLAY
1
2
Appuyez sur DVD DISPLAY en cours
de lecture.
Conseil
Vous pouvez sélectionner l’angle en appuyant
directement sur ANGLE. A chaque pression sur la
touche, l’angle change.
Le menu de commande apparaît.
Appuyez sur X/x pour sélectionner
(ANGLE).
Le numéro d’angle apparaît.
Le numéro entre parenthèses indique le
nombre total d’angles. Le témoin
« ANGLE » s’allume en vert lorsque des
angles sont enregistrés sur le disque.
53FR
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Appuyez sur X/x pour sélectionner la
langue.
Affichage des sous-titres
Les langues que vous pouvez sélectionner
diffèrent suivant les DVD.
Si 4 chiffres sont affichés, ils représentent le
code de langue. Reportez-vous à la liste des
langue le code représente.
Si des sous-titres sont enregistrés sur un disque,
vous pouvez activer ou désactiver leur affichage
à tout moment, en cours de lecture. Si des sous-
titres multilingues sont enregistrés sur le disque,
vous pouvez commuter la langue des sous-titres
en cours de lecture ou activer et désactiver les
sous-titres lorsque vous le souhaitez. Vous
pouvez sélectionner la langue dans laquelle vous
voulez vous exercer et activer les sous-titres
pour faciliter la compréhension.
Appuyez sur ENTER.
Pour annuler le réglage SOUS-
TITRE
Sélectionnez « NON » à l’étape 3.
Pour désactiver le menu de
commande
Appuyez plusieurs fois sur DVD DISPLAY
jusqu’à ce que le menu de commande
disparaisse.
Remarque
Suivant les DVD, il se peut que vous ne puissiez pas
commuter les sous-titres, même si des sous-titres
multilingues sont enregistrés sur le DVD.
SUBTITLE
Conseil
Vous pouvez directement sélectionner SOUS-TITRE
en appuyant sur la touche SUBTITLE. A chaque
pression sur cette touche, le paramètre change.
ENTER
X/x
DVD
DISPLAY
1
2
Appuyez sur DVD DISPLAY en cours
de lecture.
Le menu de commande apparaît.
Appuyez sur X/x pour sélectionner
(SOUS-TITRE), puis appuyez
sur ENTER.
Les options de SOUS-TITRE apparaissent.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
T
1 : 3 2 : 5 5
NON
1: ANGLAIS
2: FRANÇAIS
3: ESPAGNOL
54FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• CINEMA 1 : Accentue les détails des zones
sombres en augmentant le niveau de noir.
• CINEMA 2 : Accentue la luminosité des
couleurs vives et la richesse des couleurs
foncées, ainsi que le contraste des couleurs.
Réglage de l’image lue
(MODE IMAGE)
3
Sélectionnez le MODE IMAGE souhaité
à l’aide de X/x, puis appuyez sur
ENTER.
Vous pouvez régler le signal vidéo du DVD, CD
VIDEO ou du JPEG provenant de l’ampli-tuner
en vue d’obtenir la qualité d’image souhaitée.
Sélectionnez le réglage le mieux adapté au
programme regardé.
Pour désactiver le menu de
commande
Appuyez plusieurs fois sur DVD DISPLAY
jusqu’à ce que le menu de commande
disparaisse.
Conseil
Lorsque vous regardez un film, nous vous conseillons
d’opter pour « CINEMA 1 » ou « CINEMA 2 ».
ENTER
X/x
DVD
DISPLAY
Remarque
Le réglage sélectionné en MODE IMAGE est appliqué
à la totalité de l’écran.
1
2
En mode d’arrêt, appuyez sur DVD
DISPLAY.
Le menu de commande apparaît.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
(
)
1 8 3 4
1 : 3 2 : 5 5
T
STANDARD
DYNAMIQUE 1
DYNAMIQUE 2
CINEMA 1
CINEMA 2
Appuyez sur X/x pour sélectionner
(MODE IMAGE), puis appuyez
sur ENTER.
Les options de MODE IMAGE
apparaissent.
• STANDARD : Affiche une image standard.
• DYNAMIQUE 1 : Restitue une image
dynamique en augmentant le contraste et la
densité de couleur de l’image.
• DYNAMIQUE 2 : Restitue une image plus
dynamique que DYNAMIQUE 1 en
augmentant davantage encore le contraste
et la densité de couleur de l’image.
55FR
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
Insérez le disque à verrouiller.
Verrouillage de disques
(VERROUILLAGE PARENTAL
PERSONNALISE, CONTROLE
PARENTAL)
Si le disque est en cours de lecture, appuyez
sur x pour l’arrêter.
En mode d’arrêt, appuyez sur DVD
DISPLAY.
Le menu de commande apparaît.
Appuyez sur X/x pour sélectionner
(VERROUILLAGE
Vous pouvez définir deux sortes de restrictions
de lecture pour un disque.
PARENTAL PERSONNALISE), puis
appuyez sur ENTER.
• Verrouillage parental personnalisé
Vous pouvez fixer des limitations de lecture de
sorte que l’ampli-tuner ne lise pas des disques
non autorisés.
« VERROUILLAGE PARENTAL
PERSONNALISE » est sélectionné.
DVD
DVD
(
)
1 2 2 7 MAKING SCENE
• Contrôle parental
(
)
1 8 3 4
La lecture de certains DVD peut être limitée
suivant un niveau prédéterminé, tel que l’âge
des spectateurs.
T
1 : 3 2 : 5 5
Le même mot de passe est utilisé pour les
fonctions de contrôle parental et de verrouillage
parental personnalisé.
OUI
MOT DE PASSE
4
Appuyez sur X/x pour sélectionner
« OUI t », puis appuyez sur ENTER.
Verrouillage parental
personnalisé
x Si vous n’avez pas encore saisi de
mot de passe
Vous pouvez définir le même mot de passe de
verrouillage parental personnalisé pour
25 disques maximum. Si vous choisissez un 26e
disque, la restriction de lecture du disque pour
laquelle vous aviez initialement défini le mot de
passe est annulée.
L’écran de saisie d’un nouveau mot de
passe apparaît.
Verrouillage parental personnalisé
Introduisez un nouveau mot de passe à
ENTER
4 chiffres, puis appuyez sur
.
Saisissez un mot de passe à 4 chiffres à
l’aide des touches numériques, puis
appuyez sur ENTER.
Touches
numériques
L’écran de confirmation du mot de passe
apparaît.
x
ENTER
C/X/x/c
DVD
O RETURN/
DISPLAY
EXIT
56FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x Si vous avez déjà enregistré un mot
de passe
L’écran de saisie du mot de passe apparaît.
3 Saisissez un nouveau mot de passe à
4 chiffres à l’aide des touches numériques,
puis appuyez sur ENTER.
4 Pour confirmer votre mot de passe,
saisissez-le de nouveau à l’aide des
touches numériques, puis appuyez sur
ENTER.
Verrouillage parental personnalisé
Tapez le mot de passe,
ENTER
puis appuyez sur
.
Lecture d’un disque en mode
de verrouillage parental
personnalisé
5
Saisissez votre mot de passe à
4 chiffres à l’aide des touches
numériques, puis appuyez sur ENTER.
1
Insérez le disque en mode de
verrouillage parental personnalisé.
L’écran VERROUILLAGE PARENTAL
PERSONNALISE apparaît.
L’indication « Le verrouillage parental
personnalisé est activé. » apparaît et l’écran
revient alors au menu de commande.
En cas d’erreur lors de la saisie de
votre mot de passe
Appuyez sur C avant ENTER et saisissez le
bon numéro.
Verrouillage parental personnalisé
Le verrouillage parental personnalisé
est déjà activé. Tapez le mot de
ENTER
passe, puis appuyez sur
.
Si vous faites une erreur
Appuyez sur O RETURN/EXIT, puis
recommencez à l’étape 3.
2
Saisissez votre mot de passe à
4 chiffres à l’aide des touches
numériques, puis appuyez sur ENTER.
Pour désactiver le menu de
commande
Appuyez plusieurs fois sur DVD DISPLAY
jusqu’à ce que le menu de commande
disparaisse.
L’ampli-tuner est prêt pour la lecture.
Remarques
• Lorsque vous changez la couche ou la zone d’un
Super Audio CD pour lequel le verrouillage parental
personnalisé est activé, l’écran de saisie du mot de
passe peut s’afficher.
Pour désactiver la fonction de
verrouillage parental
personnalisé
• Lorsque vous définissez le mot de passe de
verrouillage parental personnalisé pour un Super
Audio CD hybride, le verrouillage ne s’applique qu’à
la couche en cours.
1 A l’étape 4, sélectionnez « NON t », puis
appuyez sur ENTER.
Conseil
2 Saisissez votre mot de passe à 4 chiffres à
l’aide des touches numériques, puis
appuyez sur ENTER.
Si vous oubliez votre mot de passe, saisissez le numéro
à 6 chiffres « 199703 » à l’aide des touches
numériques lorsque l’écran VERROUILLAGE
PARENTAL PERSONNALISE vous demande votre
mot de passe, puis appuyez sur ENTER. Il vous sera
demandé de saisir un nouveau mot de passe à
4 chiffres.
Pour changer le mot de passe
1 A l’étape 4, appuyez sur X/x pour
sélectionner « MOT DE PASSE t », puis
appuyez sur ENTER.
L’écran de saisie du mot de passe apparaît.
2 Saisissez votre mot de passe à 4 chiffres à
l’aide des touches numériques, puis
appuyez sur ENTER.
suite
57FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x Si vous n’avez pas saisi de mot de
passe
L’écran de saisie d’un nouveau mot de
passe apparaît.
Lecture limitée pour les
enfants (contrôle parental)
(DVD uniquement)
La lecture de certains DVD peut être limitée
suivant un niveau prédéterminé, tel que l’âge des
spectateurs. La fonction de « Contrôle
parental » vous permet de fixer un niveau de
limitation de la lecture.
REGLAGE PERSONNALISE
CONTROLE PARENTAL
Introduisez un nouveau mot de passe à
ENTER
4 chiffres, puis appuyez sur
.
Une scène qui est limitée n’est pas lue ou est
remplacée par une scène différente.
Saisissez un mot de passe à 4 chiffres à
l’aide des touches numériques, puis
appuyez sur ENTER.
L’écran de confirmation du mot de passe
apparaît.
x Si vous avez déjà enregistré un mot
de passe
Touches
numériques
L’écran de saisie du mot de passe apparaît.
H
REGLAGE PERSONNALISE
CONTROLE PARENTAL
Tapez le mot de passe,
ENTER
C/X/x/c
ENTER
puis appuyez sur
.
O RETURN/
EXIT
DVD
SETUP
4
Saisissez votre mot de passe à l’aide
des touches numériques, puis appuyez
sur ENTER.
1
2
En mode d’arrêt, appuyez sur DVD
SETUP.
L’écran de réglage du niveau de limitation
de la lecture et de modification du mot de
passe apparaît.
Le menu de configuration apparaît.
Appuyez sur X/x pour sélectionner
« REGLAGE PERSONNALISE », puis
appuyez sur ENTER.
REGLAGE PERSONNALISE
CONTROLE PARENTAL
NIVEAU:
STANDARD:
« REGLAGE PERSONNALISE »
apparaît.
NON
USA
CHANGER MOT DE PASSE
REGLAGE PERSONNALISE
CONTROLE PARENTAL
SELECTION DE PLAGE
DRC AUDIO:
PRIORITE CD DONNEES:
NON
NON
MP3
DATE JPEG:
MM/JJ/AAAA
3
Appuyez sur X/x pour sélectionner
« CONTROLE PARENTAL t », puis
appuyez sur ENTER.
58FR
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Appuyez sur X/x pour sélectionner
« STANDARD », puis appuyez sur
ENTER.
Si vous faites une erreur
Appuyez sur O RETURN/EXIT pour revenir à
l’écran précédent.
Les paramètres de sélection de
« STANDARD » sont affichés.
Pour désactiver le menu de
configuration
Appuyez plusieurs fois sur DVD SETUP
jusqu’à ce que le menu de configuration soit
désactivé.
REGLAGE PERSONNALISE
CONTROLE PARENTAL
NIVEAU:
STANDARD:
NON
USA
AUTRES
CHANGER MOT DE PASS
Pour désactiver la fonction de
contrôle parental et lire le DVD
après la saisie de votre mot de
passe
6
7
Appuyez sur X/x pour sélectionner une
zone géographique comme niveau de
limitation de la lecture, puis appuyez
sur ENTER.
Réglez « NIVEAU » sur « NON » à l’étape 8.
Pour changer le mot de passe
La zone est sélectionnée.
1 A l’étape 5, sélectionnez « CHANGER MOT
DE PASSE t » à l’aide de x, puis appuyez
sur ENTER.
Si vous sélectionnez « AUTRES t »,
sélectionnez le code standard dans le
l’aide des touches numériques.
L’écran de saisie du mot de passe apparaît.
2 Saisissez un nouveau mot de passe en
suivant l’étape 3.
Appuyez sur X/x pour sélectionner
« NIVEAU », puis appuyez sur ENTER.
Les paramètres de sélection de
« NIVEAU » sont affichés.
REGLAGE PERSONNALISE
CONTROLE PARENTAL
NIVEAU:
STANDARD:
NON
8:
CHANGER MOT DE PASS7:
NC17
R
6:
5:
4:
3:
2:
1:
PG13
PG
G
8
Sélectionnez le niveau souhaité à l’aide
de X/x, puis appuyez sur ENTER.
Le réglage du contrôle parental est terminé.
REGLAGE PERSONNALISE
CONTROLE PARENTAL
NIVEAU:
STANDARD:
4:
PG13
USA
CHANGER MOT DE PASSE
Plus la valeur est faible, plus la limitation est
stricte.
suite
59FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Code de zone
Norme
Lecture d’un disque en mode
de contrôle parental
Numéro de code
2109
2044
2047
2046
2057
2070
2079
2090
2092
2304
2115
2149
2165
2174
2219
2248
2238
2254
2276
2363
2362
2379
2390
2427
2376
2424
2436
2184
2489
2501
2499
2086
2543
2528
Allemagne
Argentine
Australie
Autriche
Belgique
Brésil
1
Insérez le disque et appuyez sur H.
L’écran CONTROLE PARENTAL
apparaît.
2
Saisissez votre mot de passe à
4 chiffres à l’aide des touches
numériques, puis appuyez sur ENTER.
Canada
L’ampli-tuner commence la lecture.
Chili
Remarques
Chine
• En cas de lecture d’un DVD qui ne possède pas la
fonction de contrôle parental, la lecture ne peut pas
être limitée sur cet ampli-tuner.
Corée
Danemark
Espagne
Finlande
France
• Suivant les DVD, il se peut que l’on vous demande de
modifier le niveau de contrôle parental pendant la
lecture du disque. Vous devez alors saisir le mot de
passe, puis changer de niveau. Si le mode de Reprise
de la lecture est annulé, le niveau d’origine est rétabli.
Hong Kong
Inde
Conseil
Indonésie
Italie
Si vous oubliez votre mot de passe, retirez le disque et
répétez les étapes 1 à 3 de la section « Lecture limitée
pour les enfants ». Lorsque vous êtes invité à saisir
votre mot de passe, entrez « 199703 » à l’aide des
touches numériques, puis appuyez sur ENTER. Il vous
sera demandé de saisir un nouveau mot de passe à
4 chiffres. Après avoir saisi un nouveau mot de passe à
4 chiffres à l’étape 3, replacez le disque dans l’ampli-
tuner et appuyez sur H. Saisissez votre nouveau mot
de passe, lorsque l’écran CONTROLE PARENTAL
apparaît.
Japon
Malaisie
Mexique
Norvège
Nouvelle-Zélande
Pakistan
Pays-Bas
Philippines
Portugal
Royaume-Uni
Russie
Singapour
Suède
Suisse
Taiwan
Thaïlande
60FR
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Appuyez sur TV [/1.
Le témoin RM SET UP clignote une fois.
Fonctions complémentaires
A l’aide des touches numériques,
saisissez le code du fabricant de votre
téléviseur (en vous reportant au tableau).
Commande d’autres
appareils avec la
télécommande fournie
4
Appuyez sur ENTER.
Une fois l’enregistrement terminé, le
témoin RM SET UP clignote deux fois.
Une fois l’enregistrement terminé, le
témoin RM SET UP clignote 4 fois.
En réglant le signal de commande à distance,
vous pouvez commander votre téléviseur, un
récepteur satellite ou un magnétoscope avec la
télécommande fournie.
* Utilisez exclusivement les touches numériques pour
saisir le numéro de code des téléviseurs que vous
pouvez commander à distance.
Remarques
Numéros de code des téléviseurs
pouvant être commandés
Si plusieurs numéros de code sont indiqués,
testez-les un par un jusqu’à ce que vous trouviez
celui qui fonctionne avec votre téléviseur.
• Lorsque vous saisissez un nouveau numéro de code,
ce dernier remplace le code précédemment saisi.
• Lorsque vous remplacez les piles de la
télécommande, le numéro de code peut se réinitialiser
au réglage par défaut (SONY). Réinitialisez le
numéro de code approprié.
Fabricant
SONY
Numéro de code
501,502
Conseil
Vous pouvez régler séparément le numéro de code de
votre téléviseur ou de votre récepteur satellite.
AIWA
501,502
DAEWOO
FISHER
504,505,506,507,515,544
508
Commande de téléviseurs
avec la télécommande
GOLDSTAR
GRUNDIG
HITACHI
ITT/NOKIA
JVC
503,511,512,515,534,544
517,534
513,514,515,544
521,522
TV ?/1
AV ?/1
RM SET UP
516
MAGNAVOX
503,518,544
MITSUBISHI/MGA 503,519,544
NEC
503,520,544
Touches
numériques*
PANASONIC
PHILIPS
509,524
515,518
ENTER
PIONEER
RCA/PROSCAN
SAMSUNG
SANYO
509,525,526,540
510,527,528,529,544
503,515,531,532,533,534,544
508,545,546,547
535
TV CH +/–
SHARP
TV/VIDEO
TELEFUNKEN
THOMSON
TOSHIBA
ZENITH
523,536,537,538
530,537,539
TV VOL +/–
1
Appuyez simultanément sur RM SET
UP et AV [/1.
535,540,541
542,543
Le témoin RM SET UP s’allume.
suite
61FR
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Appuyez sur ENTER.
Commande du téléviseur
Vous pouvez commander votre téléviseur à
l’aide des touches suivantes.
Une fois l’enregistrement terminé, le
témoin RM SET UP clignote deux fois.
Numéros de code des récepteurs
satellite pouvant être
commandés
Si plusieurs numéros de code sont indiqués,
testez-les un par un jusqu’à ce que vous trouviez
celui qui fonctionne avec votre récepteur
satellite.
En appuyant sur Vous pouvez
TV [/1
Mettre le téléviseur sous tension
ou hors tension.
TV/VIDEO
Basculer la source d’entrée du
téléviseur entre le téléviseur et
d’autres sources d’entrée.
TV VOL +/–
TV CH +/–
Régler le volume du téléviseur.
Changer le canal du téléviseur.
Fabricant
SONY
Numéro de code
Remarque
801,802,803,804
Suivant votre téléviseur, il est possible que vous ne
puissiez pas le commander ou utiliser certaines touches
ci-dessus.
JERROLD/G.I.
806,807,808,809,810,811,
812,813,814
PANASONIC
RCA
818
805,819
815,816,817
Commande de votre
récepteur satellite avec la
télécommande
S.ATLANTA
Commande du récepteur satellite
Appuyez sur TV/SAT.
Les sources qui peuvent être pilotées à partir de
la télécommande varient selon le réglage de TV/
SAT.
AV ?/1
RM SET UP
TV/SAT
Vous pouvez commander votre récepteur
satellite à l’aide des touches suivantes.
En appuyant sur
Vous pouvez
Touches
numériques
AV [/1
Mettre le récepteur satellite
sous tension ou hors tension.
ENTER
JUMP
Sauter
Touches
Sélectionner un canal.
numériques
ENTER
AUDIO
CH +/–
Confirmer le canal sélectionné.
Modifier le son.
Changer les chaînes.
TOP MENU/
GUIDE
Afficher le guide des
programmes.
1
Appuyez simultanément sur RM SET
UP et AV [/1.
AV MENU
Afficher le menu.
DVD DISPLAY
Mettre l’écran sous tension ou
hors tension.
Le témoin RM SET UP s’allume.
2
3
Appuyez sur TV/SAT.
O RETURN/EXIT Revenir à l’affichage précédent
du menu ou du guide des
A l’aide des touches numériques,
saisissez le code du fabricant de votre
récepteur satellite (en vous reportant
au tableau).
programmes.
C/X/x/c/ ENTER Sélectionner l’élément du
menu ou du guide des
programmes.
62FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Remarques
Fabricant
BLAUPUNKT
EMERSON
FISHER
Numéro de code
740
• Selon l’appareil, il est possible que vous ne puissiez
pas commander votre récepteur satellite ou utiliser
certaines des touches ci-dessus.
711,712,713,714,715,716,750
717,718,719,720
721,722,730
• Pour commander un lecteur de DVD, appuyez sur
DVD, puis mettez l’ampli-tuner en mode DVD.
GENERAL
ELECTRIC
GOLDSTAR
GRUNDIG
HITACHI
ITT/NOKIA
JVC
723,753
Commande du magnétoscope
avec la télécommande
724
722,725,729,741
717
AV ?/1
RM SET UP
726,727,728,736
730,731,738
MAGNAVOX
VIDEO2
VIDEO1
MITSUBISHI/MGA 732,733,734,735
NEC
736
PANASONIC
PHILIPS
729,730,737,738,739,740
729,730,731
729
Touches
numériques
PIONEER
RCA/PROSCAN
SAMSUNG
SANYO
ENTER
722,729,730,731,741,747
742,743,744,745
717,720,746
748,749
SHARP
TELEFUNKEN
TOSHIBA
ZENITH
751,752
747,755,756
754
1
Appuyez simultanément sur RM SET
UP et AV [/1.
Commande du magnétoscope
Le témoin RM SET UP s’allume.
Appuyez sur « VIDEO1 » ou « VIDEO2 ». Les
sources qui peuvent être pilotées à partir de la
télécommande varient selon le réglage de
VIDEO1 ou VIDEO2.
Vous pouvez commander votre magnétoscope à
l’aide des touches suivantes.
2
3
Appuyez sur VIDEO1 ou VIDEO2.
A l’aide des touches numériques, saisissez
le code du fabricant de votre magnétoscope
(en vous reportant au tableau).
4
Appuyez sur ENTER.
En appuyant sur
Vous pouvez
Une fois l’enregistrement terminé, le
témoin RM SET UP clignote deux fois.
AV [/1
Mettre le magnétoscope sous
tension ou hors tension.
Numéros de code des magnétoscopes
pouvant être commandés
Touches
numériques
Sélectionner un canal.
ENTER
AUDIO
CH –/+
Confirmer le canal sélectionné.
Modifier le son.
Appuyez sur VIDEO1 ou VIDEO2.
Si plusieurs numéros de code sont indiqués,
testez-les un par un jusqu’à ce que vous trouviez
celui qui fonctionne avec votre magnétoscope.
Changer les canaux du
magnétoscope.
m/M
Avancer rapidement ou revenir
en arrière rapidement.
Fabricant
SONY
Numéro de code
701,702,703,704,705,706
710,750,757,758
H
X
Lire.
AIWA
Passer en mode pause.
AKAI
707,708,709,759
suite
63FR
Download from Www.Somanuals.com. All Manuals Search And Download.
En appuyant sur
x
Vous pouvez
Arrêter.
Utilisation d’autres
appareils
AV MENU
DVD DISPLAY
Afficher le menu.
Activer ou désactiver
l’affichage.
Vous pouvez utiliser des magnétoscopes ou
d’autres appareils raccordés aux prises
VIDEO1, TV/SAT ou VIDEO2. Reportez-vous
au mode d’emploi fourni avec l’autre appareil
pour plus d’informations sur son
C/X/x/c/ ENTER Sélectionner l’élément du
menu ou du guide des
programmes.
Remarques
fonctionnement.
• Suivant votre magnétoscope, il est possible que vous
ne puissiez pas le commander ou utiliser certaines
touches ci-dessus.
TV/SAT
• Pour commander un lecteur de DVD, appuyez sur
DVD, puis mettez l’ampli-tuner en mode DVD.
VIDEO2
VIDEO1
Appuyez sur la touche « VIDEO1 »,
« VIDEO2 » ou « TV/SAT » de votre choix.
Lorsque vous appuyez sur la touche de votre
choix, l’ampli-tuner bascule vers ce mode et le
nom de l’appareil sélectionné apparaît dans la
fenêtre d’affichage du panneau frontal.
Conseil
Vous pouvez aussi sélectionner le mode à l’aide des
touches FUNCTION –/+ de l’ampli-tuner. Chaque
fois que vous appuyez sur FUNCTION –/+, l’ampli-
tuner change de mode dans l’ordre suivant.
DVD t VIDEO1 t VIDEO2 t TV/SAT t
TUNER t DVD…
64FR
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Appuyez sur AMP MENU.
Utilisation de la radio
Appuyez plusieurs fois sur X ou x
jusqu’à ce que l’indication
« MEMORY » apparaisse dans la
fenêtre d’affichage du panneau frontal.
Présélection des stations de
radio
5
Appuyez sur ENTER.
Vous pouvez présélectionner 20 stations pour la
bande FM et 10 stations pour la bande AM.
Avant de procéder à la syntonisation, veillez à
réduire le volume au minimum.
Un numéro de présélection apparaît dans la
fenêtre d’affichage du panneau frontal. Le
numéro présélectionné clignote.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
"/1
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
BAND
6
7
Appuyez plusieurs fois sur PRESET +
ou – pour sélectionner le numéro de la
présélection de votre choix.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
TUNING
–/+
PRESET
–/+
Appuyez sur ENTER.
La station est mémorisée.
ENTER X/x
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
AMP MENU
m
1
2
Appuyez plusieurs fois sur BAND
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
jusqu’à ce que la bande de votre choix
apparaisse dans la fenêtre d’affichage
du panneau frontal.
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
A chaque pression sur BAND, la bande
bascule alternativement sur AM ou FM.
La touche BAND n’est disponible que si la
fonction DVD est sélectionnée sur la
télécommande.
8
Répétez les étapes 1 à 7 pour
mémoriser d’autres stations.
Pour modifier le numéro
présélectionné
Recommencez à partir de l’étape 1.
Appuyez sur la touche TUNING + ou – et
maintenez-la enfoncée, puis relâchez-la.
Le balayage s’interrompt lorsque l’ampli-
tuner capte une station. « TUNED » et « ST »
(pour un programme stéréo) apparaissent dans
la fenêtre d’affichage du panneau frontal.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
suite
65FR
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Appuyez plusieurs fois sur BAND
jusqu’à ce que l’indication FM ou AM
apparaisse dans la fenêtre d’affichage
du panneau frontal.
Pour modifier l’intervalle de
syntonisation AM
L’intervalle de syntonisation AM peut être réglé
sur 9 kHz ou sur 10 kHz (réglage par défaut).
Pour changer d’intervalle de syntonisation,
éteignez l’ampli-tuner en appuyant sur la touche
"/1 de la télécommande. Maintenez enfoncée la
touche x (de l’ampli-tuner) et appuyez sur la
touche "/1 de l’ampli-tuner pour le mettre sous
tension. Si vous modifiez l’intervalle, les
stations AM présélectionnées sont effacées.
Pour réinitialiser l’intervalle, répétez la même
procédure.
La dernière station captée est syntonisée.
La touche BAND n’est disponible que si la
fonction DVD est sélectionnée sur la
télécommande.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
m
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Ecoute de la radio
Commencez par présélectionner des stations de
radio dans la mémoire de l’ampli-tuner (voir
2
3
Appuyez plusieurs fois sur PRESET +
ou – pour sélectionner la station
présélectionnée de votre choix.
A chaque pression sur la touche, l’ampli-
tuner syntonise une station présélectionnée.
A chaque pression sur BAND, la bande
bascule alternativement sur AM ou FM.
"/1
BAND
Réglez le volume en appuyant sur
VOLUME +/–.
FM MODE
DISPLAY/
JUMP
Pour éteindre la radio
Appuyez sur la touche "/1 de la télécommande
ou sur la touche POWER de l’ampli-tuner.
TUNING
–/+
PRESET
–/+
Pour écouter des stations de
radio non présélectionnées
Utilisez la syntonisation manuelle ou
automatique à l’étape 2.
VOLUME
+/–
Pour une syntonisation manuelle, appuyez
plusieurs fois sur la touche TUNING + ou – de
la télécommande.
Pour une syntonisation automatique, appuyez
sur la touche TUNING + ou – de la
télécommande et maintenez-la enfoncée.
Conseils
• Si un programme FM s’accompagne d’interférences,
appuyez sur la touche FM MODE de la
télécommande jusqu’à ce que « MONO » apparaisse
dans la fenêtre d’affichage du panneau frontal. Il n’y
aura aucun effet stéréo, mais la réception sera
meilleure. Appuyez une nouvelle fois sur la touche
pour restaurer l’effet stéréo.
66FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Pour améliorer la réception, réorientez les antennes
fournies.
La touche BAND n’est disponible que si la
fonction DVD est sélectionnée sur la
télécommande.
Pour vérifier la fréquence
2
Appuyez plusieurs fois sur PRESET +
ou – pour sélectionner la station
présélectionnée pour laquelle vous
souhaitez créer un nom d’index.
Appuyez plusieurs fois sur DISPLAY/JUMP.
A chaque pression sur DISPLAY/JUMP, la
fenêtre d’affichage du panneau frontal change
de la façon suivante :
nom d’index de la station* t fréquence t
nom d’index de la station...
3
4
Appuyez sur AMP MENU.
Appuyez plusieurs fois sur X ou x
jusqu’à ce que « NAME INPUT »
apparaisse.
* S’affiche si vous avez saisi un nom pour une
station présélectionnée, reportez-vous à la
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Affectation d’un nom aux
stations présélectionnées
5
6
Appuyez sur ENTER.
Créez un nom d’index à l’aide des
touches de déplacement du curseur :
Vous pouvez saisir un nom de 8 caractères
maximum pour chaque station présélectionnée.
Ces noms (par exemple, « XYZ ») apparaissent
dans la fenêtre d’affichage du panneau frontal de
l’ampli-tuner quand une station est sélectionnée.
Remarquez que vous ne pouvez pas saisir plus
d’un nom par station présélectionnée.
Appuyez sur X/x pour sélectionner un
caractère, puis appuyez sur c pour déplacer
le curseur sur la position suivante.
Si vous faites une erreur
Appuyez plusieurs fois sur C ou c jusqu’à
ce que le caractère à modifier clignote, puis
appuyez sur X/x pour sélectionner le
caractère souhaité.
BAND
7
Appuyez sur ENTER.
Le nom de la station est mémorisé.
SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE
DIGITAL EX
PRO LOGIC
ALL 1DISCS
TITLE TRACK CHAPTER INDEX
H
TUNED
M
MONO ST
S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
PRESET
–/+
Remarque
Vous ne pouvez pas saisir le nom au cours de la
syntonisation manuelle. (« Not in Use » apparaît
dans la fenêtre d’affichage du panneau frontal.)
ENTER
C/X/x/c
AMP MENU
1
Appuyez plusieurs fois sur BAND
jusqu’à ce que l’indication FM ou AM
apparaisse dans la fenêtre d’affichage
du panneau frontal.
La dernière station captée est syntonisée.
A chaque pression sur BAND, la bande
bascule alternativement sur AM ou FM.
67FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x DIMMER 2
La fenêtre d’affichage du panneau frontal et
le témoin MULTI CHANNEL
DECODING sont faiblement allumés.
Modification de la
luminosité du panneau
frontal
x DISP OFF
Eteint la fenêtre d’affichage du panneau
frontal et le témoin MULTI CHANNEL
DECODING. Quand l’ampli-tuner accepte
un signal distant entrant, le témoin s’allume
pendant 5 secondes au niveau de luminosité
DIMMER 2.
Il existe quatre niveaux de réglage de la
luminosité de la fenêtre d’affichage du panneau
frontal.
Réglez la luminosité en fonction des conditions
d’éclairage ambiantes.
Le réglage par défaut est « DIMMER OFF ».
A chaque changement de réglage, la
luminosité de la fenêtre d’affichage du
panneau frontal change comme suit :
DIMMER OFF t DIMMER 1 t
DIMMER 2 t DISP OFF t DIMMER
OFF...
ENTER
X/x
AMP MENU
1
2
Appuyez sur AMP MENU.
Réglez la fonction de la télécommande sur
DVD, puis appuyez sur AMP MENU.
Appuyez plusieurs fois sur X/x jusqu’à
ce que « DIMMER » apparaisse dans la
fenêtre d’affichage du panneau frontal,
puis appuyez sur ENTER.
3
Appuyez sur X/x pour modifier la
luminosité, puis appuyez sur ENTER
ou AMP MENU.
x DIMMER OFF
La fenêtre d’affichage du panneau frontal et
le témoin MULTI CHANNEL
DECODING brillent.
x DIMMER 1
La fenêtre d’affichage du panneau frontal et
le témoin MULTI CHANNEL
DECODING sont à moitié allumés.
68FR
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Appuyez sur X/x pour sélectionner le
paramètre de votre choix dans la liste
affichée : « CHOIX DE LA LANGUE »,
« REGLAGE DE L’ECRAN »,
Sélections et réglages
Utilisation du menu de
configuration
« REGLAGE PERSONNALISE »,
« REGLAGE H-P » et
« REINITIALISATION ». Appuyez
*
ensuite sur ENTER ou sur c.
Le paramètre de configuration sélectionné
apparaît.
L’utilisation du menu de configuration vous
permet d’effectuer divers réglages de
Exemple : « REGLAGE DE L’ECRAN »
paramètres comme l’image et le son. Vous
pouvez également, définir la langue des sous-
titres et du menu de configuration, notamment
Pour obtenir plus de détails sur chaque
paramètre du menu de configuration, reportez-
complète des paramètres du menu de
REGLAGE DE L'ECRAN
TYPE TV:
ECONOMISEUR D'ECRAN:
ARRIERE-PLAN
SORTIE COMPOSANT:
4:3 LETTER BOX
OUI
POCHETTE
INTERLACE
3
Sélectionnez un paramètre à l’aide de
X/x, puis appuyez sur ENTER ou sur c.
Comment utiliser le menu de
configuration
Les options du paramètre sélectionné
apparaissent.
Exemple : « TYPE TV »
REGLAGE DE L'ECRAN
TYPE TV:
4:3 LETTER BOX
ECONOMISEUR D'EC
4:3 PAN SCAN
16:9
ARRIERE-PLAN
SORTIE COMPOSANT:
ENTER
C/X/x/c
O RETURN/
EXIT
Options
DVD
SETUP
Appuyez sur C ou sur O RETURN/EXIT
pour revenir aux paramètres de
configuration.
4
Sélectionnez un paramètre à l’aide de
X/x, puis appuyez sur ENTER.
1
En mode d’arrêt, appuyez sur DVD
SETUP.
Le paramètre est sélectionné et la
configuration est terminée.
Le menu de configuration apparaît.
Exemple : « 4:3 PAN SCAN »
CHOIX DE LA LANGUE
ECRANS :
ANGLAIS
Paramètre
principal
MENU DVD :
ANGLAIS
ANGLAIS
ANGLAIS
AUDIO :
SOUS-TITRE :
suite
69FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Réglage sélectionné
Sélection de la langue des
menus ou de la bande son
(CHOIX DE LA LANGUE)
REGLAGE DE L'ECRAN
TYPE TV:
4:3 PAN SCAN
OUI
ECONOMISEUR D'ECRAN:
ARRIERE-PLAN
POCHETTE
INTERLACE
SORTIE COMPOSANT:
Le menu « CHOIX DE LA LANGUE » vous
permet de sélectionner différentes langues pour
les menus ou la bande son.
Pour désactiver le menu de
configuration
Sélectionnez « CHOIX DE LA LANGUE »
dans le menu de configuration. Pour obtenir plus
de détails sur l’utilisation de la fenêtre
d’affichage, reportez-vous à la section
Appuyez plusieurs fois sur DVD SETUP
jusqu’à ce que le menu de configuration soit
désactivé.
* Lorsque vous sélectionnez
« REINITIALISATION » à
l’étape 2, les
paramètres suivants retrouvent leur réglage par
défaut.
CHOIX DE LA LANGUE
ECRANS :
ANGLAIS
ANGLAIS
ANGLAIS
ANGLAIS
• Menu de configuration (sauf pour le CONTROLE
MENU DVD :
AUDIO :
SOUS-TITRE :
Après avoir sélectionné « REINITIALISATION » et
avoir appuyé sur ENTER, sélectionnez « OUI » pour
réinitialiser les réglages (cela peut prendre quelques
secondes). Sélectionnez « NON » et appuyez sur
ENTER pour annuler. N’appuyez pas sur la touche
POWER de l’ampli-tuner lorsque vous le réinitialisez.
x ECRANS (écran de menu)
Sélectionne la langue d’affichage à l’écran.
Sélectionne la langue dans la liste affichée.
x MENU DVD (DVD uniquement)
Sélectionne la langue souhaitée pour le menu
DVD.
x AUDIO (DVD uniquement)
Sélectionne la langue de la bande son.
Sélectionne la langue dans la liste affichée.
x SOUS-TITRE (DVD uniquement)
Sélectionne la langue des sous-titres.
Sélectionne la langue dans la liste affichée.
Remarque
Si vous sélectionnez une langue qui n’est pas
enregistrée sur le DVD, l’une des langues enregistrées
est automatiquement sélectionnée (sauf pour
« ECRANS »).
70FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Conseil
Si vous sélectionnez « AUTRES t » dans « MENU
DVD », « SOUS-TITRE » ou « AUDIO »,
sélectionnez et entrez le code de langue à partir de la
Après avoir effectué une sélection, le code de langue
(4 chiffres) s’affiche de nouveau lorsque vous
sélectionnez « AUTRES t ».
Réglages de l’écran
(REGLAGE DE L’ECRAN)
Choisissez les réglages en fonction du téléviseur
à raccorder.
Sélectionnez « REGLAGE DE L’ECRAN »
dans le menu de configuration. Pour obtenir plus
de détails sur l’utilisation du menu de
configuration, reportez-vous à la section
« Utilisation du menu de configuration »
Les réglages par défaut sont soulignés.
REGLAGE DE L'ECRAN
TYPE TV
4:3 LETTER BOX
ECONOMISEUR D'ECRAN:
OUI
POCHETTE
INTERLACE
ARRIERE-PLAN
SORTIE COMPOSANT:
x TYPE TV (DVD uniquement)
Sélectionne le format de l’écran du téléviseur
qui est raccordé (standard 4:3 ou écran large).
4:3
LETTER
BOX
Sélectionnez cette option si vous
raccordez un téléviseur à écran
4:3. Affiche une image large
accompagnée d’une bande noire
en haut et en bas de l’écran.
4:3
PAN SCAN
Sélectionnez cette option si vous
raccordez un téléviseur à écran
4:3. Affiche automatiquement les
images larges sur la totalité de
l’écran et coupe les parties en trop.
16:9
Sélectionnez cette option si vous
raccordez un téléviseur 16:9 ou un
téléviseur possédant une fonction
de mode large.
suite
71FR
Download from Www.Somanuals.com. All Manuals Search And Download.
x SORTIE COMPOSANTE
4:3 LETTER BOX
Permet de modifier le type du signal émis par les
prises COMPONENT VIDEO OUT de l’ampli-
plus d’informations sur les différents types.
4:3 PAN SCAN
INTERLACE
Sélectionnez ce paramètre lorsque
vous être raccordé à un téléviseur
standard (format entrelacé).
PROGRESSIVE
Sélectionnez ce paramètre lorsque
vous disposez d’un téléviseur qui
peut accepter les signaux
progressifs.
16:9
Remarque
Remarque
Si vous avez réglé « SORTIE COMPOSANTE » dans
Suivant les DVD, il se peut que « 4:3 LETTER BOX »
soit automatiquement sélectionné au lieu de « 4:3 PAN
SCAN » et inversement.
« REGLAGE DE L’ECRAN » sur
« PROGRESSIVE » alors que votre téléviseur
n’accepte pas les signaux au format progressif,
maintenez les touches x et . enfoncées
simultanément pendant quelques secondes. Le
paramètre « SORTIE COMPOSANTE » retrouve le
réglage « INTERLACE ».
x ECONOMISEUR D’ECRAN
Active et désactive l’économiseur d’écran afin
qu’un écran de veille apparaisse lorsque vous
laissez l’ampli-tuner en mode de pause ou
d’arrêt pendant 15 minutes ou lorsque vous lisez
un CD, un Super Audio CD, un MP3 ou un
fichier JPEG (sauf en cas de diaporama) pendant
plus de 15 minutes. L’économiseur d’écran
évite toute altération de votre écran (consécutive
à l’affichage prolongé d’une même image).
Appuyez sur H pour désactiver l’économiseur
d’écran.
OUI
Active l’économiseur d’écran.
NON
Désactive l’économiseur d’écran.
x ARRIERE-PLAN
Sélectionne la couleur d’arrière-plan ou de
l’image affichée sur l’écran du téléviseur en
mode d’arrêt ou pendant la lecture d’un CD.
POCHETTE
La pochette (image fixe) apparaît
en arrière-plan, mais uniquement
si une pochette est déjà enregistrée
sur le disque (CD-EXTRA, etc.).
Si le disque ne comporte pas de
pochette, l’image
« GRAPHIQUE » apparaît.
GRAPHIQUE
Une image mémorisée dans l’ampli-
tuner apparaît en arrière-plan.
BLEU
NOIR
L’arrière-plan est de couleur bleue.
L’arrière-plan est de couleur noire.
72FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Si les plages audio PCM, DTS, MPEG et Dolby
Digital disposent du même nombre de canaux,
l’ampli-tuner sélectionne les plages audio PCM,
DTS, Dolby Digital et MPEG dans cet ordre.
• Suivant le DVD, le canal audio prioritaire peut être
prédéterminé. Dans ce cas, vous ne pouvez pas
donner la priorité aux formats audio DTS, Dolby
Digital ou MPEG en sélectionnant « AUTO ».
Réglages personnalisés
(REGLAGE PERSONNALISE)
Permet de régler le contrôle parental et d’autres
paramètres.
x DRC AUDIO (AUDIO DYNAMIC RANGE
COMPRESSION)
Sélectionnez « REGLAGE PERSONNALISE »
dans le menu de configuration. Pour obtenir plus
de détails sur l’utilisation du menu de
configuration, reportez-vous à la section
« Utilisation du menu de configuration »
Réduit la largeur de la gamme DYNAMIQUE
de la bande son.
Utile pour regarder des films à faible volume en
soirée.
NON
Aucune compression de la gamme
DYNAMIQUE.
Les réglages par défaut sont soulignés.
STANDARD
Reproduit la bande son en respectant
la gamme DYNAMIQUE prévue
par l’ingénieur du son au moment de
l’enregistrement.
REGLAGE PERSONNALISE
CONTROLE PARENTAL
SELECTION DE PLAGE
DRC AUDIO:
PRIORITE CD DONNEES:
NON
NON
MP3
DATE JPEG:
MM/JJ/AAAA
MAX
Réduit complètement la largeur de la
gamme DYNAMIQUE.
Remarque
La compression de la gamme DYNAMIQUE
s’applique uniquement aux sources Dolby Digital.
x CONTROLE PARENTAL t (DVD
uniquement)
Définit un mot de passe et un niveau de
limitation de lecture pour les DVD comportant
des limitations de lecture pour les enfants. Pour
plus de détails, reportez-vous à la section
« Lecture limitée pour les enfants (contrôle
x PRIORITE CD DONNEES (MP3, JPEG
uniquement)
Définissez les données prioritaires que vous
souhaitez lire, lors de la lecture des plages audio
MP3 et des fichiers d’image JPEG d’un CD de
données (CD-ROM/CD-R/CD-RW).
x SELECTION DE PLAGE (DVD
uniquement)
MP3
S’il existe un fichier MP3 sur le
disque, l’ampli-tuner reconnaît le
disque comme « disque MP3 ». Si le
disque ne contient que des fichiers
JPEG, l’ampli-tuner reconnaît le
disque comme « disque JPEG ».
Affiche la bande son qui comporte le plus grand
nombre de canaux prioritaires lorsque vous
effectuez la lecture d’un DVD sur lequel
plusieurs formats audio (PCM, MPEG audio,
DTS ou Dolby Digital) sont enregistrés.
JPEG
S’il existe un fichier JPEG sur le
disque, l’ampli-tuner reconnaît le
disque comme « disque JPEG ». Si
le disque ne contient que des fichiers
MP3, l’ampli-tuner reconnaît le
disque comme « disque MP3 ».
NON
Aucune priorité accordée.
Priorité accordée.
AUTO
Remarques
• Lorsque vous réglez le paramètre sur « AUTO », la
langue peut changer. Le réglage « SELECTION DE
PLAGE » a une priorité supérieure aux réglages
« AUDIO » de « CHOIX DE LA LANGUE »
suite
73FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Remarques
• Lors de la lecture des CD multi-session, l’ampli-tuner
détermine la cible à lire comme dernière session ou
comme session liée à celle-ci.
Réglages des enceintes
(REGLAGE H-P)
• Si vous modifiez ce paramètre, réinsérez le disque.
Pour optimiser le son surround, réglez en
fonction de la taille des enceintes que vous avez
raccordées et leur distance par rapport à la
position d’écoute. Utilisez ensuite le test de
tonalité pour régler le niveau et la balance des
enceintes au même niveau.
x DATE JPEG
Modifiez l’ordre des informations relatives à la
date d’une image JPEG dans le menu de
commande.
MM/JJ/AAAA
AAAA/MM/JJ
JJ/MM/AAAA
AAAA/JJ/MM
Sélectionnez « REGLAGE H-P » dans le menu
de configuration. Pour plus d’informations,
reportez-vous à la section « Utilisation du menu
AAAA : Année
MM : Mois
JJ : Jour
Les réglages par défaut sont soulignés.
REGLAGE H-P
TILLE:
DISTANCE:
NIVEAU:
ÉQUILIBRE:
TEST TONALITE:
Pour revenir au réglage par
défaut après une modification
Sélectionnez le paramètre, puis appuyez sur
CLEAR.
Seul le paramètre sélectionné retrouve son
réglage par défaut.
x TAILLE
Si vous utilisez de petites enceintes ou si vous ne
raccordez pas d’enceinte centrale, d’enceintes
surround ou d’enceintes arrière surround, ou
encore si vous déplacez les enceintes surround,
réglez les paramètres des enceintes AVANT,
CENTRE, SURROUND, SURROUND
ARRIERE et du INFRAGRAVE.
AVANT
GRAND : Sélectionnez ce
paramètre par défaut.
PETIT : Sélectionnez ce paramètre
si vous utilisez des enceintes avant
de petite taille.
74FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Si « SURROUND » est réglé sur « GRAND »
ou « PETIT »
CENTRE
GRAND : Sélectionnez ce
paramètre par défaut.
« SURROUND ARRIERE » doit avoir le même
réglage ou être réglé sur « NEANT ».
PETIT : Sélectionnez ce paramètre
si vous utilisez une enceinte centrale
de petite taille.
Si « INFRAGRAVE » est réglé sur
« NEANT »
NEANT :Sélectionnezce paramètre
si vous n’utilisez aucune enceinte
centrale.
« AVANT » doit être réglé sur « GRAND ».
Remarques
• Lorsque vous sélectionnez un paramètre, le son est
momentanément coupé.
SURROUND
GRAND (DERRIERE, BAS),
GRAND (DERRIERE, HAUT),
GRAND (LATERAL, BAS),
GRAND (LATERAL, HAUT),
PETIT (DERRIERE, BAS),
• Suivant les réglages, le niveau de sortie du caisson de
graves peut être excessif.
PETIT (DERRIERE, HAUT),
PETIT (LATERAL, BAS),
Définition de la position et de la
hauteur des enceintes surround
Si vous sélectionnez un réglage différent de
« NEANT » sous « SURROUND », spécifiez la
taille, la position et la hauteur des enceintes
surround.
PETIT (LATERAL, HAUT) :
Spécifiez la taille, la position et la
hauteur de mise en oeuvre correcte
des modes Digital Cinema Surround
Pour plus d’informations, reportez-
vous à la section « Définition de la
position et de la hauteur des
enceintes surround » ci-dessous.
NEANT :Sélectionnezce paramètre
si vous n’utilisez aucune enceinte
surround.
DERRIERE
(BAS) :
Sélectionnez ce paramètre si les
enceintes surround se trouvent
dans les parties B et D.
DERRIERE
(HAUT) :
Sélectionnez ce paramètre si les
enceintes surround se trouvent
dans les parties B et C.
SURROUND
ARRIERE
GRAND : Sélectionnez ce
paramètre par défaut.
COTE (BAS) :
Sélectionnez ce paramètre si les
enceintes surround se trouvent
dans les parties A et D.
PETIT : Sélectionnez ce paramètre
si vous utilisez une enceinte arrière
surround de petite taille.
COTE (HAUT) :
Sélectionnez ce paramètre si les
enceintes surround se trouvent
dans les parties A et C.
NEANT :Sélectionnezce paramètre
si vous n’utilisez aucune enceinte
arrière surround.
Ces paramètres ne sont pas accessibles si
« SURROUND » est réglé sur « NEANT ».
INFRAGRAVE
OUI : Sélectionnez ce paramètre si
vous utilisez un caisson de graves.
NEANT :Sélectionnezce paramètre
si vous n’utilisez aucun caisson de
graves.
Définition des limitations
Il existe quelques limitations de taille. Certains
paramètres sont automatiquement modifiés.
Si « AVANT » est réglé sur « PETIT »
« CENTRE », « SURROUND » et
« SURROUND ARRIERE » doivent être réglés
sur « PETIT » ou « NEANT ».
suite
75FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Veillez à modifier la valeur dans le menu de
configuration lorsque vous déplacez les
enceintes.
Schéma des positions
AVANT
3 m/10 pieds
La distance des enceintes avant par
rapport à la position d’écoute peut être
définie par incréments de 0,3 mètre (1
pied), entre 0,9 et 6,9 mètres (3 et 23
pieds).
90
A
B
A
CENTRE
3 m/10 pieds
L’enceinte centrale peut être
rapprochée de 1,5 mètre (5 pieds)
maximum de la position d’écoute par
rapport à la position des enceintes
avant, par incréments de 0,3 mètre (1
pied).
45
B
20
Schéma des hauteurs
SURROUND
3 m/10 pieds
La distance des enceintes surround peut
être réduite jusqu’à 4,5 mètres
(15 pieds) maximum de la position
d’écoute par rapport à l’enceinte avant,
par incréments de 0,3 mètre (1 pied).
C
D
C
60
30
D
SURROUND
ARRIERE
3 m/10 pieds
La distance de l’enceinte arrière
surround peut être réduite jusqu’à
4,5 mètres (15 pieds) de la position
d’écoute par rapport à l’enceinte
avant, par incréments de 0,3 mètre
(1 pied).
Conseil
La position et la hauteur des enceintes surround
sont spécialement étudiées pour le mode
CINEMA STUDIO EX.
Remarques
• Lorsque vous définissez une distance, le son est
momentanément coupé.
x DISTANCE
• Si chaque enceinte avant ou surround n’est pas placée
à une distance égale de votre position d’écoute,
définissez la distance par rapport à l’enceinte la plus
proche.
Le réglage de distance par défaut des enceintes
par rapport à la position d’écoute est illustré ci-
dessous.
• Ne placez pas les enceintes surround plus loin que les
enceintes avant par rapport à votre position d’écoute.
3m
(10pieds)
x NIVEAU
3m
(10pieds)
3m
(10pieds)
Vous pouvez modifier le niveau de chaque
enceinte de la façon suivante. Veillez à régler
« TEST TONALITE » sur « OUI » pour
faciliter le réglage.
CENTRE
0 dB
Règle le niveau de l’enceinte
centrale (–10 dB à +10 dB, pas de 1
dB).
3m
(10pieds)
3m
(10pieds)
3m
(10pieds)
SURROUND
GAUCHE 0 dB
SURROUND
DROIT 0 dB
Règle le niveau des enceintes
surround (–10 dB à +10 dB, pas de
1 dB).
SURROUND
ARRIERE
0 dB
Règle le niveau des enceintes
arrière surround (–10 dB à +10 dB,
pas de 1dB).
76FR
Download from Www.Somanuals.com. All Manuals Search And Download.
INFRAGRAVE
0 dB
Règle le niveau du caisson de
graves (–10 dB à +10 dB, pas de 1
dB).
Réglage de l’équilibre et du
niveau des enceintes à l’aide
du test de tonalité
x ÉQUILIBRE
1
Appuyez sur DVD SETUP en mode
d’arrêt.
Vous pouvez faire varier la balance des
enceintes gauche et droite de la façon suivante.
Veillez à régler « TEST TONALITE » sur
« OUI » pour faciliter le réglage.
Le menu de configuration apparaît.
2
3
4
Appuyez plusieurs fois sur X ou x pour
sélectionner « REGLAGE H-P », puis
appuyez sur ENTER.
AVANT
CENTRE
Règle la balance entre les enceintes avant
gauche et droite. La position centrale est
indiquée par « --- ». (Vous pouvez régler 6
pas vers la gauche ou la droite par rapport
au centre.)
Appuyez plusieurs fois sur X ou x pour
sélectionner « TEST TONALITE », puis
appuyez sur ENTER.
Appuyez plusieurs fois sur X ou x pour
sélectionner « OUI », puis appuyez sur
ENTER.
Pour régler simultanément le
volume de toutes les enceintes
Utilisez la commande VOLUME de l’ampli-
tuner ou appuyez sur la touche VOLUME +/– de
la télécommande.
Le test de tonalité est émis successivement
par chaque enceinte.
5
Depuis votre position d’écoute,
sélectionnez la valeur des paramètres
« ÉQUILIBRE » et « NIVEAU » à l’aide
de C/X/x/c.
x TEST TONALITE
Les enceintes émettent une tonalité de test pour
régler les paramètres « NIVEAU » et
« ÉQUILIBRE ».
Lorsque vous sélectionnez
« ÉQUILIBRE », le test de tonalité est émis
simultanément par les enceintes gauche et
droite.
Lorsque vous sélectionnez « LEVEL », le
test de tonalité n’est émis que par l’enceinte
que vous réglez.
NON
OUI
Le test de tonalité n’est pas émis par les
enceintes.
Le test de tonalité est émis successivement
par chaque enceinte. Lorsque
« ÉQUILIBRE » est sélectionné, le test de
tonalité est émis simultanément par les
enceintes gauche et droite. Lorsque
« NIVEAU » est sélectionné, le test de
tonalité n’est émis que par l’enceinte que
vous réglez.
6
7
Appuyez sur ENTER lorsque vous avec
terminé les réglages.
Appuyez plusieurs fois sur X ou x pour
sélectionner « TEST TONALITE », puis
appuyez sur ENTER.
8
Appuyez plusieurs fois sur X ou x pour
sélectionner « NON », puis appuyez
sur ENTER.
Remarque
Lorsque vous réglez les enceintes, le son est
momentanément coupé.
Conseil
Pour ajuster la balance ou le niveau sans écouter
la tonalité de test, sélectionnez « ÉQUILIBRE »
ou « NIVEAU » à l’étape 3, puis appuyez sur
ENTER. Ajustez ensuite la balance ou le niveau
à l’aide de X/x, puis appuyez sur ENTER.
77FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Même si vous réglez le format d’écran dans
« TYPE TV » sous « REGLAGE DE L’ECRAN »,
l’image ne remplit pas l’écran.
Informations complémentaires
• Le format d’image du disque est fixe.
Dépannage
L’image est en noir et blanc.
• Suivant les téléviseurs, l’image à l’écran apparaît
en noir et blanc lorsque vous lisez un disque
enregistré avec un système couleur NTSC.
Si vous rencontrez l’une des difficultés
suivantes lors de l’utilisation de cet ampli-tuner,
consultez ce guide de dépannage pour tenter de
remédier au problème. Si le problème persiste,
consultez votre revendeur Sony le plus proche.
Son
Il n’y a pas de son.
• Le cordon d’enceinte n’est pas raccordé
correctement.
Alimentation
L’ampli-tuner ne se met pas sous tension.
• Vérifiez que le cordon d’alimentation secteur est
correctement raccordé.
• Le cordon de raccordement est endommagé.
Remplacez-le par un cordon neuf.
• Appuyez sur la touche MUTING de la
télécommande si « MUTING ON » est affiché
dans la fenêtre d’affichage du panneau frontal.
• L’ampli-tuner se trouve en mode de pause ou de
lecture au ralenti. Appuyez sur H pour revenir
en mode de lecture normale.
Image
Il n’y a pas d’image.
• Les cordons de raccordement vidéo ne sont pas
raccordés correctement.
• Les cordons de raccordement vidéo sont
endommagés.
• Vous utilisez la fonction d’avance ou de retour
rapide. Appuyez sur H pour revenir en mode de
lecture normale.
• L’appareil n’est pas raccordé à la prise d’entrée
• Sélectionnez « DEC. PRI. » sous AMP MENU et
choisissez « AUTO » lors de la lecture de signaux
DTS-CD à partir d’un appareil externe raccordé à
la prise DIGITAL IN (OPTICAL IN/COAXIAL
• Le réglage de l’entrée vidéo du téléviseur ne
permet pas de visionner les images à partir de
l’ampli-tuner.
• Vous avez réglé « SORTIE COMPOSANTE »
dans « REGLAGE DE L’ECRAN » sur
« PROGRESSIVE » même si votre téléviseur
n’accepte pas les signaux au format progressif.
Dans ce cas, maintenez les touches x et .
enfoncées simultanément pendant quelques
secondes. « SORTIE COMPOSANTE » retrouve
le réglage « INTERLACE ».
Les sons gauche et droite ne sont pas
équilibrés ou ils sont inversés.
• Vérifiez que les enceintes et les composants sont
raccordés correctement.
• Réglez le paramètre de balance dans le menu
• Même si votre téléviseur est compatible avec les
signaux progressifs (480p), l’image e peut être
affectée lorsque vous réglez « SORTIE
COMPOSANTE » sur « PROGRESSIVE ». En
pareil cas, réglez « SORTIE COMPOSANTE »
sur « INTERLACE ».
Le caisson de graves n’émet aucun son.
• Vérifiez les réglages et les raccordements des
• Réglez le champ acoustique sur « AUTO
FORMAT DIRECT AUTO » (page 45).
Le son est parasité par un bourdonnement ou
des interférences sont émises.
L’image comporte des parasites.
• Le disque est sale ou défectueux.
• Vérifiez que les enceintes et les composants sont
raccordés correctement.
• Si les signaux vidéo de votre appareil doivent
passer par votre magnétoscope pour atteindre
votre téléviseur, les signaux de protection contre
la copie enregistrés sur certains DVD peuvent
affecter la qualité de l’image. Si ces problèmes
persistent lorsque vous raccordez votre ampli-
tuner directement à votre téléviseur, essayez de
raccorder l’appareil à l’entrée S-vidéo de votre
• Vérifiez si les cordons de raccordement sont bien
éloignés d’un transformateur ou d’un moteur, et se
trouvent à 3 mètres (10 pieds) au moins d’un
téléviseur ou d’un éclairage fluorescent.
• Eloignez votre téléviseur des autres composants.
78FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Les fiches et les prises sont sales. Essuyez-les
avec un chiffon légèrement imbibé d’alcool.
• Sélectionnez « DEC. PRI. » sous AMP MENU et
choisissez « AUTO » lors de la lecture de signaux
DTS-CD à partir d’un appareil externe raccordé à
la prise DIGITAL IN (OPTICAL IN/COAXIAL
• Suivant la source, l’effet des enceintes surround/
arrière surround peut être moins tangible.
Utilisation
Impossible de syntoniser des stations radio.
• Vérifiez que les antennes sont correctement
raccordées. Réglez les antennes ou raccordez une
antenne extérieure si nécessaire.
• Nettoyez le disque.
Lorsque la lecture du CD (signal PCM)
démarre, aucun son ne se produit au départ.
• Sélectionnez « DEC. PRI. » dans le AMP MENU
• Le signal des stations est trop faible (lorsque vous
effectuez la syntonisation automatiquement).
Utilisez la syntonisation manuelle.
• Aucune station n’a été présélectionnée ou les
stations présélectionnées ont été supprimées
(lorsque vous effectuez la syntonisation en
balayant les stations présélectionnées).
• Appuyez sur DISPLAY/JUMP pour faire
apparaître la fréquence dans la fenêtre
d’affichage.
Le son n’a plus l’effet stéréo lorsque vous
écoutez un CD VIDEO, un CD ou un fichier
MP3.
• Réglez « AUDIO » sur « STEREO » dans la
• Assurez-vous que l’ampli-tuner est correctement
raccordée.
La télécommande ne fonctionne pas.
• La télécommande est réglée pour commander une
ou plusieurs autres appareils. Appuyez sur la
touche DVD,VIDEO1, VIDEO2 ou TV/SAT de la
L’effet surround est difficilement décelable
lors de la lecture d’une bande son Dolby
Digital ou MPEG.
• Vérifiez que la fonction de champ acoustique est
• Des obstacles se trouvent entre la télécommande
et l’ampli-tuner.
• Vérifiez les réglages et les raccordements des
• Rapprochez la télécommande de l’ampli-tuner.
• Dirigez la télécommande vers le capteur de
télécommande de l’ampli-tuner.
• Suivant le DVD, le signal de sortie peut ne pas être
reproduit sur la totalité des 5.1 canaux ou des 6.1
canaux. Il peut être mono ou stéréo même si la
bande son est enregistrée au format audio Dolby
Digital ou MPEG.
• Remplacez les piles de la télécommande si elles
sont faibles.
La lecture du disque ne démarre pas.
• Il n’y a pas de disque à l’intérieur.
• Le disque est inséré à l’envers.
Introduisez le disque avec la face de lecture
orientée vers le bas sur le plateau de lecture.
• Le disque est posé de biais dans le plateau de
lecture.
Le son est diffusé uniquement par l’enceinte
centrale.
• Suivant les disques, il se peut que le son ne soit
diffusé que par l’enceinte centrale.
Aucun son n’est diffusé par l’enceinte
centrale.
• Vérifiez les raccordements et les réglages de
l’enceinte.
• L’ampli-tuner ne peut pas lire de CD-ROM, etc.
• Vérifiez que la fonction de champ acoustique est
• Le code local figurant sur le DVD n’est pas
compatible avec l’ampli-tuner.
Aucun son ou un son très faible uniquement
est diffusé par les enceintes surround/arrière
surround.
• De l’humidité s’est condensée dans l’ampli-tuner.
Retirez le disque et laissez l’ampli-tuner sous
• Vérifiez les raccordements et les réglages de
l’enceinte.
Impossible de lire la plage audio MP3.
• Le CD de données n’est pas enregistré au format
MP3 conformément aux normes ISO9660 Niveau
1/ Niveau 2 ou Joliet.
• Assurez-vous que les enceintes surround sont
réglées sur « PETIT » ou « GRAND ».
• Vérifiez que la fonction de champ acoustique est
• La plage audio MP3 ne possède pas l’extension
« .MP3 ».
• Sélectionnez un champ acoustique contenant le
suite
79FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Les données ne sont pas formatées au format MP3
bien qu’elles en aient l’extension (« .MP3 »).
• L’ampli-tuner peut uniquement lire des fichiers
audio MP3 (MPEG1 Audio Layer3).
• La fonction de reprise de la lecture a été
sélectionnée.
Pendant l’arrêt, appuyez sur la touche x de
l’ampli-tuner ou de la télécommande, puis
• Retirez le disque et sélectionnez « REGLAGE
PERSONNALISE » parmi les paramètres de
configuration. Sélectionnez ensuite « PRIORITE
CD DONNEES » et choisissez de nouveau
• Le titre, le menu DVD ou le menu PBC apparaît
automatiquement sur l’écran du téléviseur.
L’ampli-tuner commence automatiquement la
lecture du disque.
• Il y a plus de 8 niveaux de répertoires.
• Le DVD possède une fonction de lecture
automatique.
Le titre de l’album ou de la plage audio MP3
n’est pas affiché correctement.
La lecture s’arrête automatiquement.
• Certains disques contiennent un signal de pause
automatique. En cours de lecture d’un disque de
ce type, l’ampli-tuner arrête la lecture au signal de
pause automatique.
• L’ampli-tuner peut uniquement afficher des
chiffres et des lettres de l’alphabet. Les autres
caractères sont remplacés par « ».
Impossible de lire le fichier image JPEG.
• Le CD de données n’est pas enregistré au format
JPEG conformément aux normes ISO9660
Niveau 1/Niveau 2 ou Joliet.
L’ampli-tuner s’est éteint pendant la lecture
d’un DVD.
• Si le menu principal du DVD ou un menu du DVD
demeure affiché pendant une heure environ au
cours de la lecture d’un DVD, ou si une pause dure
au moins une heure, l’ampli-tuner s’éteint
automatiquement.
• Le fichier image JPEG ne possède pas l’extension
« .JPG » ou « .JPEG ».
• Les données ne sont pas formatées au format
JPEG bien qu’elles aient l’extension « .JPG » ou
« .JPEG ».
Impossible d’exécuter certaines fonctions,
telles que l’arrêt de lecture, la recherche, la
lecture au ralenti, la lecture répétée, aléatoire
ou programmée.
• La longueur ou la largeur de l’image dépasse
4 720 points.
• Retirez le disque et sélectionnez « REGLAGE
PERSONNALISE » parmi les paramètres de
configuration. Sélectionnez ensuite « PRIORITE
CD DONNEES » et choisissez de nouveau
• Suivant le disque, il est possible que vous ne
puissiez pas exécuter certaines opérations
mentionnées ci-dessus. Reportez-vous au mode
d’emploi accompagnant le disque.
• Il y a plus de 8 niveaux de répertoires.
• Vous ne pouvez pas lire les fichiers JPEG
progressifs.
Les messages n’apparaissent pas sur l’écran
du téléviseur dans la langue souhaitée.
• Dans le menu de configuration, sélectionnez la
langue de votre choix pour l’affichage à l’écran
dans « ECRANS » sous « CHOIX DE LA
Le titre d’un album ou d’un fichier JPEG n’est
pas affiché correctement.
• L’ampli-tuner peut uniquement afficher des
chiffres et des lettres de l’alphabet. Les autres
caractères sont remplacés par « ».
Impossible de changer la langue de la bande
son.
L’écran de saisie du mot de passe n’apparaît
pour un Super Audio CD, alors que le
verrouillage parental personnalisé est activé.
• Le verrouillage parental personnalisé est activé
pour différentes couches d’un Super Audio CD.
• Il n’y a pas de plages multilingues enregistrées sur
le DVD en cours de lecture.
• Le DVD ne permet pas de changer la langue de la
bande son.
Impossible de changer la langue des sous-
titres.
La lecture d’un disque ne commence pas à
partir du début.
• Il n’y a pas de sous-titres multilingues enregistrés
sur le DVD en cours de lecture.
• La fonction Lecture programmée, Lecture
aléatoire ou Lecture répétée a été sélectionnée
• Le DVD ne permet pas de changer les sous-titres.
Appuyez sur CLEAR pour annuler ces fonctions
avant de démarrer la lecture d’un disque.
80FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Les sous-titres ne peuvent pas être
Spécifications
désactivés.
• Le DVD ne permet pas de désactiver les sous-
titres.
SPECIFICATIONS DE PUISSANCE AUDIO
PUISSANCE DE SORTIE ET
DISTORSION HARMONIQUE
Impossible de commuter les angles.
• Plusieurs angles ne sont pas enregistrés sur le
DVD qui est en cours de lecture (page 53).
• Le DVD ne permet pas de changer les angles.
TOTALE :
Avec des charges de
8 ohms, les deux canaux
étant excités, de
Impossible d’éjecter un disque et « LOCKED »
apparaît dans la fenêtre d’affichage du
panneau frontal.
20 à 20 000 Hz ;
puissance efficace de
100 watts nominaux
minimum par canal, avec
une distorsion
• Contactez votre revendeur Sony ou un centre de
service après-vente Sony agréé.
« PROTECT » apparaît dans la fenêtre
d’affichage du panneau frontal.
harmonique totale ne
dépassant pas 0,7 %, de
250 milli watts à la
puissance nominale de
sortie.
• Le circuit de protection des enceintes fonctionne.
• Vérifiez les raccordements des enceintes.
L’ampli-tuner ne fonctionne pas normalement.
• Si le fonctionnement de l’ampli-tuner est affecté,
appuyez sur sa touche POWER pour le mettre
hors tension, puis remettez-le sous tension.
Partie amplificateur
Mode stéréo
100 W + 100 W (8/4 ohms,
20 – 20 000 Hz, THD 0,7
%)
Mode surround
Avant : 100 W + 100 W
Centre* : 100 W
Surround* : 100 W +
100 W
Surround arrière* : 100 W
(8/4 ohms, 20 – 20 000 Hz,
THD 0,7 %)
*
Suivant les réglages du champ acoustique et de la
source, il est possible qu’aucun son ne soit émis.
Entrées (analogiques)
Entrées (numériques)
ANALOG IN :
Sensibilité : 150 mV
Impédance : 50 kilohms
DIGITAL IN
OPTICAL :
DIGITAL IN
COAXIAL :
Impédance : 75 ohms
SUB WOOFER OUT :
Tension : 3 V
Impédance : 100 ohms
PHONES :
Accepte les casques à
basse et haute impédance
DIGITAL OUT
OPTICAL
Sorties (analogiques)
Sorties (numériques)
suite
81FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Lecteur Super Audio CD/DVD
Laser A semi-conducteur
Caractéristiques générales
Alimentation électrique
120 V CA, 60 Hz
Consommation électrique 180 W
(Super Audio CD/DVD :
1 W (en mode d’économie
d’énergie)
λ = 650 nm)
(CD : λ = 780 nm)
Durée d’émission :
continue
Dimensions (approx.)
430 × 100 × 450 mm
3
(17 × 4 × 17 /4 pouces)
(l/h/p) parties saillantes
comprises
7,0 kg (15 lb 7 oz)
Système de format des signaux
NTSC
Poids (approx.)
Température de fonctionnement
5°C à 35°C (41°F à 95°F)
Humidité de fonctionnement
5 % à 90 %
Partie tuner FM
Système
Système de synthétiseur
numérique à boucle à
verrouillage de phase à
quartz
Accessoires fournis
Gamme de syntonisation 87,5 – 108,0 MHz (pas de
100 kHz)
La conception et les spécifications sont sujettes à
modification sans préavis.
Antenne
Fil d’antenne FM
Bornes d’antenne
75 ohms, dissymétrique
Fréquence intermédiaire 10,7 MHz
Partie tuner AM
Système
Système de synthétiseur
numérique à boucle à
verrouillage de phase à
quartz
Gamme de syntonisation 530 – 1 710 kHz (avec
l’intervalle réglé sur
10 kHz)
531 – 1 710 kHz (avec
l’intervalle réglé sur
9 kHz)
Antenne
Fil d’antenne
Fréquence intermédiaire 450 kHz
Partie vidéo
Entrées
Vidéo :
1 Vp-p 75 ohms
S vidéo :
Y : 1 Vp-p 75 ohms
C : 0,286 Vp-p 75 ohms
Vidéo :
Sorties
1 Vp-p 75 ohms
S vidéo :
Y : 1 Vp-p 75 ohms
C : 0,286 Vp-p 75 ohms
Composante :
Y : 1 Vp-p 75 ohms
PB/CB : 0,7 Vp-p
PR/CR : 0,7 Vp-p
82FR
Download from Www.Somanuals.com. All Manuals Search And Download.
En utilisant des écrans de menu enregistrés sur
les CD VIDEO avec des fonctions PBC, vous
pouvez bénéficier d’une lecture simple et
interactive de programmes, programmes avec
des fonctions de recherche, etc.
Glossaire
Album
Il s’agit d’une section d’un morceau musical ou
d’une image sur un CD de données contenant
des plages audio MP3 ou des fichiers JPEG.
Contrôle parental
Fonction offerte par un DVD pour restreindre la
lecture des disques suivant l’âge des spectateurs
et qui repose sur un niveau de limitation propre
à chaque pays. La limitation varie d’un disque à
l’autre. Lorsqu’elle est activée ou que la lecture
est totalement interdite, les scènes violentes sont
omises ou remplacées par d’autres scènes, etc.
CD VIDEO
Disque compact contenant des images animées.
Les données vidéo utilisent le format MPEG 1,
un norme internationale de technologie de
compression numérique. Les données vidéo sont
compressées environ 140 fois en moyenne. Par
conséquent, un CD VIDEO de 12 cm peut
contenir jusqu’à 74 minutes d’images animées.
Les CD VIDEO contiennent également des
données audio compactes. Les sons qui ne sont
pas perçus par l’oreille humaine sont
compressés alors que les autres ne le sont pas.
Un CD VIDEO peut contenir 6 fois plus
d’informations audio que les CD classiques.
Il existe 2 versions de CD VIDEO.
Digital Cinema Sound (DCS)
Ce nom générique couvre le son surround
produit par la technologie de traitement des
signaux numériques développée par Sony.
Contrairement aux champs acoustiques
surround antérieurs qui étaient principalement
axés sur la reproduction de la musique, Digital
Cinema Sound est spécialement conçu pour la
restitution de la bande son des films.
• Version 1.1 : Vous pouvez lire uniquement des
images animées et des sons.
Dolby Digital
Ce format de son pour les films est plus avancé
que la technologie Dolby Surround Pro Logic.
Dans ce format, le son stéréo émis par les
enceintes surround avec une gamme de
fréquence étendue et un canal de caisson de
graves pour les graves profondes est produit
indépendamment. Ce format est aussi appelé
« 5.1 », car le canal du caisson de graves
constitue le 0,1 canal (étant donné qu’il ne
fonctionne que lorsqu’un effet de graves
renforcé est requis). Les six canaux de ce format
sont enregistrés séparément pour obtenir une
meilleure séparation des canaux. De plus, étant
donné que tous les signaux sont traités
numériquement, ils sont moins dégradés.
• Version 2.0 : Vous pouvez lire des images
fixes de haute résolution et bénéficier des
fonctions PBC.
Cet ampli-tuner est compatible avec les deux
versions.
Chapitre
Subdivision d’un titre sur un DVD. Un titre est
composé de plusieurs chapitres.
Code local
Cet ampli-tuner est utilisé pour protéger les
droits d’auteur. Un code local est affecté à
chaque chaîne DVD ou disque DVD en fonction
des régions de distribution. Le code local est
indiqué sur l’ampli-tuner et sur l’emballage du
disque. L’ampli-tuner peut lire les disques dont
le numéro correspond à son code local. L’ampli-
tuner peut également lire des disques portant la
ALL
Dolby Digital EX
Format amélioré, compatible Dolby Digital 5.1,
développé par Dolby Laboratories et Lucasfilm
THX, qui ajoute un canal arrière supplémentaire
et qui peut être utilisé pour la lecture de 6.1
canaux (trois enceintes surround) à partir d’un
encodage matriciel.
marque «
». Ainsi, même si le code local
n’apparaît pas sur le DVD, la limite de zone peut
être activée.
Contrôle de lecture (PBC)
Signaux encodés sur les CD VIDEO
(version 2.0) pour contrôler la lecture.
suite
83FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Dolby Pro Logic II
DTS-ES
La technologie Dolby Pro Logic II crée cinq
canaux de sortie à large bande passante à partir
de sources limitées à deux canaux. Ceci est
réalisé à l’aide d’un décodeur ambiophonique à
matrice haute-fidélité qui extrait les propriétés
spatiales de l’enregistrement original sans
l’ajout de colorations sonores.
Format amélioré compatible 5.1 canaux qui
ajoute un canal arrière surround supplémentaire.
Il existe deux formats : Discrete 6.1, qui traite le
signal arrière surround de manière indépendante
et Matrix 6.1 qui le traite conjointement avec les
canaux surround (gauche et droit).
DVD
x Mode film (Movie mode)
Disque contenant jusqu’à 8 heures d’images
animées pour un format identique à celui d’un
CD.
Le mode film est utilisé par les programmes de
télévision stéréo et toutes les émissions codées
en Dolby Surround. Le résultat est une
amélioration de la directionnalité du champ
acoustique qui se rapproche de la qualité sonore
discrète en 5.1 canaux.
La capacité de données d’un DVD simple
couche et simple face (4,7 Go (Giga-octets)) est
7 fois supérieure à celle d’un CD. De plus la
capacité de données d’un DVD double couche et
simple face est de 8,5 Go, celle d’un DVD
simple couche et double face est de 9,4 Go et
celle d’un DVD double couche et double face est
de 17 Go.
x Mode musique (Music mode)
Le mode musique doit être utilisé avec tous les
enregistrements musicaux stéréo et fournit un
espace sonore large et profond.
Les données vidéo utilisent le format MPEG 2,
l’une des normes internationales appliquées
pour la technologie de compression numérique.
Les données vidéo sont compressées environ
40 fois en moyenne. Le DVD utilise également
la technologie de codage à débit variable qui
traite les données allouées en fonction du statut
de l’image.
Dolby Surround Pro Logic
Il s’agit de l’une des méthodes de décodage
Dolby Surround. Dolby Surround Pro Logic
produit quatre canaux à partir d’un son à deux
canaux. Comparé au système Dolby Surround
précédent, Dolby Surround Pro Logic reproduit
un effet panoramique de gauche à droite plus
naturel et localise les sons plus précisément.
Pour profiter pleinement de Dolby Surround Pro
Logic, vous devez disposer d’une paire
Les données audio sont enregistrées en Dolby
Digital et en PCM, ce qui vous permet d’écouter
des sons d’une présence accrue.
d’enceintes surround et d’une enceinte centrale.
Les enceintes surround émettent un son mono.
En outre, diverses fonctions avancées, telles que
les fonctions d’angles multiples, de
multilinguisme et de contrôle parental, sont
également accessibles sur les DVD.
DTS
Technologie de compression audio numérique
développée par Digital Theater Systems, Inc.
Cette technologie est compatible avec le son
surround 5.1 canaux. Ce format comprend des
canaux surround stéréo et un canal caisson de
graves discret. Le DTS fournit les mêmes
5.1 canaux discrets de haute qualité audio
numérique. Une séparation exceptionnelle des
canaux est ainsi obtenue, car toutes les données
des canaux sont enregistrées de façon discrète et
traitées de manière numérique.
Fichier
Section d’un CD de données contenant des
fichiers image JPEG.
Fonction d’angles multiples
Divers angles d’une scène, ou points de vue de
la caméra vidéo, sont enregistrés sur certains
DVD.
Fonction multilingue
Plusieurs langues pour le son ou les sous-titres
d’une image sont enregistrées sur certains DVD.
84FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Format entrelacé (balayage
entrelacé)
Plage
Il s’agit des sections d’une image ou d’un
morceau musical sur un Super Audio CD, CD,
CD VIDEO ou MP3. Un album se compose de
plusieurs plages (MP3 uniquement).
Le format entrelacé constitue la méthode
standard NTSC d’affichage des images TV au
rythme de 30 images par seconde. Chaque
image est balayée deux fois : entre les lignes de
balayage paires et les lignes de balayage
impaires, au rythme de 60 balayages par
seconde.
Scène
Sur un CD VIDEO disposant de fonctions PBC
(contrôle de lecture), les écrans de menu, les
images animées et les images fixes sont divisés
en sections appelées « scènes ».
Format progressif (balayage
séquentiel)
Super Audio CD
Par rapport au format entrelacé, le format
progressif peut reproduire 60 images par
seconde et donc toute les lignes de balayage
(525 lignes pour le système NTSC). La qualité
globale de l’image s’en trouve améliorée et les
images fixes, le texte et les lignes horizontales
sont plus nets. Ce format est compatible avec le
format progressif 525.
Un disque Super Audio CD peut reproduire les
sons de manière extrêmement fidèle à l’original
grâce à la technologie DSD (Direct Stream
Digital). Celle-ci utilise une fréquence
d’échantillonnage de 2,8224 MHz, soit 64 fois
celle d’un CD conventionnel, et une
quantification 1 bit qui multiplie par 4 la
quantité d’informations que le disque peut
contenir par rapport à un CD ordinaire au format
PCM. Les Super Audio CD sont répartis en
plusieurs types.
Logiciels basés sur des films,
logiciels basés sur des vidéos
Les DVD peuvent être classés comme logiciels
basés sur des films ou sur des vidéos. Les DVD
basés sur les films contiennent les mêmes
images (24 images par seconde) que ceux
passant dans les salles de cinéma. Les DVD
basés sur des vidéos, comme les téléfilms ou les
sitcoms, affichent les images à une vitesse de
30 images (60 champs) par seconde.
• Super Audio CD (disque monocouche)
Ce disque est constitué d’une seule couche
HD*.
* Couche de signaux haute densité du Super Audio
CD
Couche HD (haute
densité)
Neo:6
Développé par Digital Theater Systems, Inc.,
applique un signal de source Dolby Digital ou 2
canaux conventionnel à un décodeur matriciel
numérique de haute précision pour obtenir une
lecture surround à 6.1 canaux.
Le mode CINEMA permet une meilleure
séparation des canaux et rehausse ainsi l’effet du
6.1 canaux. Il est particulièrement adapté aux
films.
• Super Audio CD (disque bicouche)
Ce disque est constitué de deux couches HD et
offre une durée de lecture étendue.
En outre, le disque bicouche est constitué de
deux couches HD sur une seule face et il n’est
pas nécessaire de le retourner au cours de la
lecture.
Le mode MUSIC permet de ne pas traiter les
canaux gauche et droit avant afin d’obtenir un
effet stéréo optimal tandis que l’ajout de
composantes surround ajoute une qualité
particulière au son.
Couche HD
Couche HD
suite
85FR
Download from Www.Somanuals.com. All Manuals Search And Download.
• Super Audio CD + CD (disque hybride)
Ce disque est constitué d’une couche HD et
d’une couche CD. En outre, comme les deux
couches sont sur une même face, vous ne
devez pas retourner le disque pendant la
lecture. Vous pouvez lire cette touche CD à
l’aide d’un lecteur de CD conventionnel.
Couche CD
Couche HD
• Super Audio CD 2 canaux + multi-canaux
Ce disque est constitué d’une zone de lecture à
2 canaux et d’une zone de lecture multi-
canaux.
Zone de lecture à
2 canaux
Zone de lecture multi-
canaux
Titre
Il s’agit de la section la plus longue d’une image
ou d’un morceau musical sur un DVD, d’un
film, etc., pour un logiciel vidéo ou de l’album
entier pour un logiciel audio.
86FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Index des composants et des commandes
Pour plus de détails, reportez-vous aux pages indiquées entre parenthèses.
Panneau frontal
VOLUME
POWER
STANDBY
SOUND FIELD
2CH
A. F. D.
MODE
DISPLAY
TUNER/PRESET
FUNCTION
PHONES
C
(Capteur de télécommande) (12)
D 2CH (45)
P Fenêtre d’affichage du panneau frontal
I Témoin MULTI CHANNEL DECODING
(Décodage multi-canaux) (68)
R TUNER/PRESET –/+ (Tuner/
Présélection –/+ ) (65)
suite
87FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Fenêtre d’affichage du panneau frontal
Pendant la lecture d’un DVD
Statut de lecture
S’allume lorsque vous changez d’angle
SACD
ALL 1DISCS
DVD
CD
VIDEO CD
HYBRID
ANGLE
MP3
PBC NTSC PROGRESSIVE
MONO ST S
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Numéro du titre en Numéro du chapitre
en cours
Temps de
lecture
Son en cours
Mode en cours
cours
Lors de la lecture d’un Super Audio CD, CD, CD VIDEO ou MP3
S’allume en lecture PBC
(CD VIDEO uniquement)
Mode de lecture en cours Disque en cours
Son en cours
SACD
ALL 1DISCS
DVD
CD
VIDEO CD
HYBRID
ANGLE
MP3
PBC NTSC PROGRESSIVE
MONO ST S
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Numéro d’index en cours
(Le numéro d’index
n’apparaît pas pendant la
lecture d’un Super Audio
CD ou MP3.)
Statut de lecture
Numéro de la
plage en
cours
Temps de lecture
Pendant l’écoute de la radio
Numéro de présélection
Effet mono/stéréo
SACD
ALL 1DISCS
DVD
CD
VIDEO CD
PBC NTSC PROGRESSIVE
HYBRID
ANGLE
MP3
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
MONO ST S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Bande en cours
Station en cours
Pendant la lecture d’un fichier JPEG
Statut de lecture
SACD
ALL 1DISCS
DVD
CD
VIDEO CD
PBC NTSC PROGRESSIVE
HYBRID
ANGLE
MP3
DIGITAL EX
PRO LOGIC
TITLE TRACK CHAPTER INDEX H TUNED
M
MONO ST S
SHUFFLE
REPEAT1 FM AM
PROGRAM MEMORY
dB PCM DSD NEO:
kHz DTS-ES 96/24
MHz MPEG-2 AAC
6
Mode en cours
Numéro du fichier en cours
88FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Panneau arrière
ANTENNA
COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO2 VIDEO1 MONITOR TV/SAT VIDEO2 VIDEO1
(DVD ONLY)
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
FM
75
PB/CB
PR/CR
AM
Y
COAXIAL
OUT
IN
IN
IN
OUT
IN
IN
IN
L
AUDIO
OUT
R
COAXIAL IN
TV/SAT
OPTICAL IN
TV/SAT VIDEO2
OPTICAL AUDIO
OUT IN
AUDIO
IN
AUDIO
IN
BACK
R
L
R
L
SURROUND
CENTER
FRONT
SUB
DIGITAL
TV/SAT VIDEO2 VIDEO1
SPEAKERS
IMPEDANCE USE 4-16
WOOFER
K Prise VIDEO1 (VIDEO IN) (Vidéo 1
(Entrée vidéo)) (18)
L Prise SUB WOOFER (ANALOG OUT)
(Caisson de graves (Sortie
analogique))(13)
C Prises COMPONENT VIDEO OUT
(Sortie vidéo composante) (18)
D Prise MONITOR (S VIDEO OUT)
(Moniteur (Sortie S vidéo)) (18)
N Prise VIDEO1 (AUDIO L/R IN) (Vidéo 1
E Prise TV/SAT (S VIDEO IN) (TV/Satellite
(Entrée audio G/D)) (18)
(Entrée S vidéo)) (18)
O Prise VIDEO2 (AUDIO L/R IN) (Vidéo 2
F Prise VIDEO2 (S VIDEO IN) (Vidéo 2
(Entrée audio G/D)) (18)
(Entrée S vidéo)) (18)
P Prise TV/SAT (AUDIO L/R IN) (TV/
G Prise VIDEO1 (S VIDEO IN) (Vidéo 1
Satellite (Entrée audio G/D)) (18)
(Entrée S vidéo)) (18)
Q Prise DIGITAL (OPTICAL OUT)
H Prise MONITOR (VIDEO OUT)
(Numérique (Sortie optique)) (19)
(Moniteur (Sortie vidéo)) (18)
R Prise DIGITAL (OPTICAL IN VIDEO2)
(Numérique (Entrée optique Vidéo 2))
I Prise TV/SAT (VIDEO IN) (TV/Satellite
(Entrée vidéo)) (18)
J Prise VIDEO2 (VIDEO IN) (Vidéo 2
S Prise DIGITAL (OPTICAL IN TV/SAT)
(Numérique (Entrée optique TV/
Satellite)) (19)
(Entrée vidéo)) (18)
T Prise DIGITAL (COAXIAL IN TV/SAT)
(Numérique (Entrée coaxiale TV/
Satellite)) (19)
suite
89FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Télécommande
F 2CH (45)
J ./>, CH –/+ (Canal –/+), PRESET
M TOP MENU/GUIDE ALBUM– (Menu
Remarques
• Cette télécommande est phosphorescente dans
l’obscurité pour autant qu’elle ait été préalablement
exposée à la lumière pendant un certain temps.
• Lorsque vous utilisez un lecteur de DVD, appuyez
sur DVD 4, puis modifiez le mode de l’amplituner
en sélectionnant DVD.
ez m/M, SLOW (Ralenti)
/
,
A RM SET UP (Configuration de la
ed OPEN/CLOSE (Ouverture/Fermeture)
ef AV MENU/ALBUM+ (Menu AV/Album+)
90FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Liste des codes de langue
L’orthographe des langues est conforme à la norme ISO 639 : 1988 (E/F).
Code
Langue
Code
Langue
Code
Langue
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
Afar
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
1345
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1436
1463
1481
1482
1483
Inupiak
1489
1491
1495
1498
1501
1502
1503
1505
1506
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali; Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Latin
Lingala
Welsh
Danish
German
Bhutani
Greek
Laothian
Lithuanian
Latvian; Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Twi
Ukrainian
Urdu
Frisian
Irish
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Punjabi
Uzbek
Vietnamese
Volap k
Wolof
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Xhosa
Yoruba
Chinese
Zulu
Polish
Hindi
Pashto; Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Non spécifiée
1703
Romanian
92FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Liste des paramètres du menu de configuration DVD
Vous pouvez régler les paramètres suivants avec le menu de configuration DVD.
Les réglages par défaut sont soulignés.
CHOIX DE LA LANGUE
REGLAGE DE L’ECRAN
a)
ECRANS
(Sélectionnez la langue de
TYPE TV
4:3 LETTER
BOX
4:3 PAN SCAN
16:9
OUI
NON
POCHETTE
GRAPHIQUE
BLEU
NOIR
INTERLACE
PROGRESSIVE
votre choix à partir de la liste
des langues affichées.)
ECONOMISEUR
D’ECRAN
ARRIERE-PLAN
a)
MENU DVD
(Sélectionnez la langue de
votre choix à partir de la liste
des langues affichées.)
a)
AUDIO
(Sélectionnez la langue de
votre choix à partir de la liste
des langues affichées.)
SORTIE
COMPOSANTE
SOUS-
TITRE
(Sélectionnez la langue de
votre choix à partir de la liste
des langues affichées.)
a)
REGLAGE PERSONNALISE
CONTROLE NIVEAU
PARENTAL
NON
8.
7. NC17
a)
6.
5.
4. PG13
R
3.
PG
2.
1.
G
STANDARD
USA
AUTRESt
CHANGER MOT DE PASSE
SELECTION NON
a)
DE PLAGE
AUTO
DRC
AUDIO
NON
STANDARD
MAX
b)
PRIORITE
CD
DONNEES
MP3
JPEG
c)
DATE JPEG MM/JJ/AAAA
AAAA/MM/JJ
JJ/MM/AAAA
AAAA/JJ/MM
a) DVD uniquement
b) Sources Dolby Digital uniquement
c) MP3, JPEG uniquement
suite
93FR
Download from Www.Somanuals.com. All Manuals Search And Download.
REGLAGE H-P
TAILLE
AVANT
GRAND
PETIT
GRAND
PETIT
NEANT
CENTRE
SURROUND
GRAND (DERRIERE, BAS)
GRAND (DERRIERE, HAUT)
GRAND (LATERAL, BAS)
GRAND (LATERAL, HAUT)
PETIT (DERRIERE, BAS)
PETIT (DERRIERE, HAUT)
PETIT (LATERAL, BAS)
PETIT (LATERAL, HAUT)
NEANT
SURROUND
ARRIERE
GRAND
PETIT
NEANT
INFRAGRAVE OUI
NEANT
0,9m – 6,9m/
DISTANCE
AVANT
3 pieds – 23 pieds
(3 m/10 pieds)
0,9m – 6,9m/
3 pieds – 23 pieds
(3 m/10 pieds)
CENTRE
0,9m – 6,9m/
3 pieds – 23 pieds
(3 m/10 pieds)
SURROUND
0,9m – 6,9m/
3 pieds – 23 pieds
(3 m/10 pieds)
SURROUND
ARRIERE
–10 dB – +10 dB
(0 db)
–10 dB – +10 dB
(0 db)
NIVEAU CENTRE
SURROUND
GAUCHE
SURROUND
DROIT
–10 dB – +10 dB
(0 db)
SURROUND
ARRIERE
–10 dB – +10 dB
(0 db)
–10 dB – +10 dB
(0 db)
INFRAGRAVE
ÉQUILIBRE AVANT
6 pas à gauche
ou à droite
(CENTRE)
TEST
TONALITE
NON
OUI
REINITIALISATION
OUI
NON
94FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Chiffres
E
P
ECONOMISEUR D’ECRAN
Ecran de menu
Affichage du menu de
A
R
Raccordements du téléviseur et
F
Fenêtre d’affichage du panneau
B
C
REGLAGE PERSONNALISE
I
S
J
Sélection du mode de décodage
D
L
Lecture continue
CD/VIDEO CD/Super Audio
T
M
V
VERROUILLAGE PARENTAL
N
95FR
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp All in One Printer AR 207 User Manual
Sharp Appliance Trim Kit RK66A User Manual
Sharp Calculator EL 5230 User Manual
Sharp CRT Television 32SF560 User Manual
Sigma Digital Camera C21EN0291 User Manual
Sony Car Video System AVD S10 User Manual
Sony Microcassette Recorder M 335 User Manual
Sony Video Game Console SCPH 35001 GT 97010 User Manual
SUPER MICRO Computer Security Camera 6015B 3 User Manual
Tally Genicom Printer T9220 User Manual