Sekonic Digital Camera L 758 User Guide

DIGITALMASTER  
L-758DR  
L-758D  
L-758    
Operating Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Precautions  
Before using your light meter, please read this “Safety Precautions” carefully and  
use it properly.  
Indicates hazard or unsafe use that can result in  
personal injury or death.  
WARNING  
Indicates hazard or unsafe use that can result in  
personal injury or damage to your light meter.  
CAUTION  
NOTE:  
Indicates a caution or limitation that accompanies op-  
eration. Please read the note to avoid incorrect opera-  
tion.  
Reference: Provides the reference information and related functions  
that are useful in operating. We recommend that you  
read these references.  
WARNING  
Please place light meter in a location where an infant cannot reach and  
accidentally get the strap wrapped around his or her neck. There is dan-  
ger of strangulation.  
Keep the synchro terminal cap out of reach of young children, as swal-  
lowing such objects can cause suffocation.  
Never place batteries in fire, short, disassemble, heat or charge them.  
The batteries might break down, and cause damage, injury or pollute  
the environment.  
CAUTION  
There is a danger of electric shock and damage to product if your meter  
is handled with wet hands, in the rain, near water or where there is a lot  
of moisture, when you use cord flash mode. If you are using flash mode  
in these conditions, we recommend Cordless Flash mode or Radio Trig-  
gering mode. Always attach the synchro terminal cap on to the synchro  
connector when the light meter is exposed to wet or rainy conditions.  
Do not look directly at the sun through the viewfinder, because of poten-  
tial eye injury.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Safety Precautions  
Table of Contents  
1. Parts Designation ............................................................................................... 1  
1. Light Meter Parts .............................................................................................. 1  
2. Supplied Accessories ....................................................................................... 2  
2. Explanation of the Liquid Crystal Display(LCD) ............................................. 3  
3. Before Using ....................................................................................................... 7  
1. Attach the strap ................................................................................................ 7  
2. Inserting the battery.......................................................................................... 7  
3. Checking battery capacity ................................................................................ 7  
4. Replacing the battery during measurement or when using the memory function .. 8  
5. Auto Power Off function ................................................................................... 8  
6. Setting ISO 1 sensitivity ................................................................................... 8  
7. Setting ISO 2 sensitivity ................................................................................... 8  
8. Jog Wheel Lock or Lock Off ............................................................................. 9  
9. Setting the Measuring and Memory button configuration ................................. 10  
4. Basic Operation.................................................................................................. 11  
1. Incident or reflected spot measuring ................................................................ 11  
2. Setting measuring mode .................................................................................. 12  
3. Incident Measurement Mode ............................................................................ 13  
4. Reflected Measurement Mode (spot metering) ................................................ 14  
5. Measurement ...................................................................................................... 15  
1. Measuring ambient light ................................................................................... 15  
1-1Shutter Speed Priority mode ...................................................................... 15  
1-2Aperture Priority mode ................................................................................ 17  
1-3EV mode ..................................................................................................... 18  
1-4Cinematography ......................................................................................... 19  
2. Measuring electronic flash................................................................................ 21  
2-1Cord Flash mode ........................................................................................ 21  
2-2Auto-reset cordless flash mode .................................................................. 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
2-3Cord multiple flash (cumulative) mode ....................................................... 24  
2-4Cordless multiple flash (cumulative) mode ................................................. 25  
2-5Flash analyzing function ............................................................................. 27  
2-6Wireless Flash Radio Triggering................................................................. 28  
6. Advanced Functions .......................................................................................... 31  
1. Memory function ............................................................................................... 31  
2. Averaging function ............................................................................................ 32  
3. Contrast Function ............................................................................................. 32  
4. How to use an incident illuminance (LUX or FC) meter (L-758DR/758D) ........ 34  
5. How to use a reflected luminance (cd/m2 or FL) meter (L-758DR/758D) ......... 35  
6. How to use the Exposure compensation function ............................................ 36  
7. How to use Calibration compensation function ................................................ 37  
8. Filter compensation .......................................................................................... 38  
8-1Filter compensation (1) ............................................................................... 38  
8-2Filter factor number compensation (2) (L-758CINE only) ........................... 39  
9. Custom setting function .................................................................................... 40  
7. Camera Exposure Profiling ............................................................................... 42  
1. Calibration testing for exposure profiling .......................................................... 42  
2. Input test target data ........................................................................................ 44  
2-1Sekonic Application software ...................................................................... 44  
2-1-1Outline of software ............................................................................. 44  
2-2Manual Exposure Profile Input ................................................................... 45  
3. How to use Exposure Profiling mode ............................................................... 48  
3-1Selecting Camera Exposure Profiling ......................................................... 48  
3-2Analog scale ............................................................................................... 48  
3-2-1Aperture scale.................................................................................... 48  
3-2-2EV scale............................................................................................. 48  
3-2-3MID.TONE button .............................................................................. 49  
8. Optional Accessories......................................................................................... 52  
9. Technical Data .................................................................................................... 54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
10.Care and Maintenance ...................................................................................... 56  
FCC & IC compliance information ........................................................................ 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Parts Designation  
Lumisphere retracting ring  
Lumisphere  
1. Light Meter Parts  
Liquid Crystal Display (LCD)  
!Spot Lens  
Average / EV (Brightness Difference)  
Memory button*  
button  
Jog Wheel  
Power button  
(ON/OFF switch)  
ISO 2 button (“B” in radio channel setting)  
@USB Port  
@Memory Clear button  
(“D” in radio channel setting)  
ISO 1 button  
(“A” in radio channel setting)  
Flash Synchro terminal  
Mid-Tone button  
("C" in radio channel setting)  
Mode button  
Strap eyelet  
!I9  
ncident/Reflected Spot  
Selector Dial  
@
2
Eyepiece (with Diopter  
Adjustment)  
Measuring button*  
Battery Compartment Cover  
@14 /4” Tripod Socket  
Battery Cover Latch  
RT-32FCC/CE Radio  
transmitter module  
Battery Compartment  
@Connector cover  
L-758DR  
*Measuring button and memory button can be  
swithced in Custom settings.  
L-758D/L-758CINE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-1-  
1. Parts Designation  
2. Supplied Accessories  
@6  
@S7  
trap  
@L8  
ens Cap  
(Attached to meter)  
@U9  
SB Cable  
#C0  
D-ROM for Software  
(Data Transfer Software, USB driver,  
Operating manual and Software guide)  
#Sticker for Multi-key Operation and CS  
(Custom Setting)  
#Q2  
uick Guide (in Japanese/English)  
#O3 perating Manual  
#B4  
attery (CR-123A)  
#S5 oft Case  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-2-  
2. Explanation of the Liquid Crystal Display (LCD)  
LCD for L-758DR/L-758D  
LCD for L-758CINE  
NOTE:  
For explanation purposes, the display illustrated here shows all icons and readouts  
simultaneously. Actual LCD screen will not show all icon as above during normal  
use.  
Auto Electro-Luminescent Display (EL)  
• In low light (EV 6 or less), a green backlight will automatically illuminate the entire LCD.  
• The LCD will not be automatically illuminated during measurements, in Cordless Flash or Wireless  
flash radio triggering mode.  
• The Electro-luminescent backlight will automatically turn off 20 seconds after last operation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-3-  
2. Explanation of the Liquid Crystal Display  
Display in viewfinder  
In setting : ⑧  
Flash analyzing : ④  
Luminance :  
/
(Only L-758CINE)  
Measuring Mode Icons  
Ambient (see page 15)  
Auto-Reset Cordless Flash (see page 22)  
Cord Flash (see page 21)  
Wireless flash radio triggering mode (see page 28)  
Incident / Reflected Spot Mode Icons (see page 11)  
Appears when in Incident mode  
Appears when in Reflected Spot mode  
ISO Display (see page 8)  
Displays ISO 1 setting  
Displays second ISO setting when ISO 2 button is pressed  
Flash Analyzing indicator (see page 27)  
0 to 100% in 10% increments (percentage of the flash in the total exposure)  
+/- Exposure/Calibration Compensation display (see page 36)  
Exposure compensation--- appears on the upper side of the main LCD.  
Calibration compensation--- appears only in the calibration setting mode.  
Digital aperture value, Aperture Priority, EV Brightness Difference, Average function, EV display  
Appears when Aperture Priority (f/stop) mode is selected (see page 17)  
Appears when using Contrast function (see Page 32)  
Appears when using Averaging function and Contrast function (see page 32)  
Appears when using EV mode (see page 18)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-4-  
2. Explanation of the Liquid Crystal Display  
Analog Scale  
Displays measured values as icons along the apertures or Latitude EV scale. The scale is graduated  
in full or 1/3 stop increments for measurements. Memorized and averaged values are also display  
along the scale.  
Aperture scale (upper scale) displays in all mode except Aperture priority mode.  
f 0.7 to f 90 in full stops appears in all modes except aperture priority mode (L-758)  
f 0.5 to f 64 in full stops appears in all modes except aperture priority mode (L-758CINE)  
EV scale (lower scale) displays in all mode except Multiple flash cumulative mode.  
+/-7 stops from Mid.Tone (0) appears in aperture priority mode, or other modes if selected.  
Value display scale  
Appear to indicate last measured/ memorized/ averaged values and brightness differ-  
ence value below the aperture scale or above the latitude scale depending on which  
scale has been selected.  
Appears when measurement is below display range  
Blinks when measurement is below measurement range  
Appears when measurement is above display range  
Blinks when measurement is above measurement range  
Dynamic range/clipping point icons  
Indicates dynamic range and clipping point of a selected camera exposure profiling.  
Shutter priority indicator, shutter speed display for still photography or frames per second (f/s) for  
cinematography  
Appears when Shutter Priority (T) is selected mode (see page 15)  
Appears when shutter speed is in minutes  
Appears when shutter speed is in full seconds  
Appears when cine speed is set in frames per second (see page 19)  
Battery Power Indicator (see page 7)  
Memory / Multiple Flash Indicator Display  
Appears when Multi (cumulative) flash measurement mode is selected and shows the  
cumulated number of flash measurements (see page 24)  
Appears when reading is memorized and shows the number in memory (see page 31)  
Radio triggering channel and Quad-triggering zone display (see page 28)  
Triggering Channel Numbers  
Selective Quad-Triggering Zone  
Camera profile selector display  
USB icon  
Appears when a USB cable is connected to the light meter and a computer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-5-  
2. Explanation of the Liquid Crystal Display  
Shutter angle (L-758CINE)  
Appears when shutter angle is set to a value other than 180 degrees (see page 19)  
Illuminance mark / Luminance mark (L-758CINE)  
Appears when Foot-Candle is selected  
Appears when Lux is selected  
Appears when Foot-Lambert is selected  
Appears when cd/m2 is selected  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-6-  
3. Before Using  
O
O
1. Attach the strap  
Attach the Strap @by passing the small loop end through the  
M
eyelet and passing the other end of strap through it.  
WARNING  
To avoid a danger of strangulation, please keep the strap in a location where an infant  
cannot reach it and accidentally get the strap wrapped around his or her neck.  
2. Inserting the battery  
1. Requires one 3.0 v CR123A lithium battery (included).  
2. Open the Battery compartment cover latch , and re-  
move the Battery compartment cover .  
3. Insert the battery, observing the polarity with the +,- marks  
in the battery compartment .  
4. Align the tabs of the Battery compartment cover with the  
notches in the back of the meter, and press down to close  
the Battery compartment cover latch.  
NOTE:  
To prevent loss of All-weather seal, be careful that dirt does not get stuck on the rubber  
seal and that the seal is not damaged.  
Remove battery if meter is not used for an extended period. Batteries can leak and  
damage the light meter. Dispose of used batteries properly.  
If the LCD does not light, check that the battery capacity is sufficient, and check that the  
battery positive and negative terminals are not reversed.  
The L-758D/L-758CINE has a connector for a plug-in radio transmitter module. Do not  
remove the connector cover unless you are installing the radio module, failure to do so  
could cause the electronic circuit board to be exposed to damaging static electricity.  
3. Checking battery capacity  
When the Power button is ON, the battery power indicator on the LCD is displayed.  
(Displayed) Battery power level is good.  
(Displayed) Battery power level is low. Have a spare battery ready.  
(Blinking)  
Replace battery immediately.  
Reference:  
• If the LCD screen turns off immediately after the display appears when power is first  
applied, that is an indication that the battery is dead. Please promptly replace the battery.  
We recommend you always have a spare battery on hand.  
• A spare battery can be stored in a provided compartment of the L-758DR's case (see  
sticker "OPEN END TO BACK".  
• Under our testing condition, the battery life is approximately 60 hours with continuous  
use under normal temperature.  
• The battery supplied with this light meter, may not be able to meet battery life mentioned  
above because of undetermined shelf life or storage condition.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-7-  
3. Before Using  
4. Replacing the battery during measurement or when using the memory function  
1. Always turn the power OFF before replacing the battery. If the battery is removed with the  
power ON, measurements and settings in memory can no longer be recalled.  
2. If after replacing the battery, or during measurements, strange screens (displays that have not  
been set) appear on the LCD, or nothing happens, no matter what button is pushed, remove the  
battery and wait at least ten seconds and then replace the battery. This allows the software to  
automatically reset.  
WARNING:  
Never place batteries in fire, short, disassemble, or heat them. The batteries might break  
down, and cause an accident, injury or pollute the environment.  
NOTE:  
A three second pause between power on and off is recommended to avoid damage to  
the meter.  
5. Auto Power Off function  
1. To conserve battery power, the meter will turn off about twenty minutes after last use.  
2. Whether the Auto Power Saving feature turns the power off or the Power button is pressed,  
the settings and measured values remain stored in memory. When the Power button is pressed  
again the last settings are displayed.  
Reference:  
The power shuts off automatically after 1 minute when the power button is pressed and held.  
Auto power off time is adjustable in Custom settings. (See page 40 for details)  
6. Setting ISO 1 sensitivity  
1. Hold down the ISO1 button and turn the Jog wheel  
to select the desired ISO sensitivity.  
2. You can also change the ISO sensitivity after taking  
measurements. The new value is automatically  
displayed.  
7. Setting ISO 2 sensitivity  
1. This feature is useful when using a different ISO  
sensitivity (film or digital), Polaroid proofing film, or for  
exposure correction (when using a filter, extension  
tubes, bellows factor or another camera etc.).  
2. Hold down the ISO 2 button and turn the Jog wheel  
to select the desired ISO sensitivity.  
3. Once this is set, after taking a measurement, the mea-  
sured value for the second ISO sensitivity will be dis-  
played when the ISO 2 button is pressed.  
4. You can also change the second ISO sensitivity after  
taking measurements. The new value is automatically  
displayed.  
Reference:  
The following settings are possible when using custom setting function P40.  
1. It is possible to set ISO 2 for Filter compensation. These values can be set within a range of  
±5 EV in 1/10 steps and are display in the ISO 2 area.  
2. Filter factor number compensation enables you to set seven types of filters frequently used  
in the CINE industry. (Kodak Wratten Filters)(L-758CINE only)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-8-  
3. Before Using  
8. Jog Wheel Lock or Lock Off  
1. Hold down the Mode button and ISO1 button ⑪  
and LOCwill appear to indicate that the Jog Wheel is  
locked. The last measurement is held until the lock is  
released, even if the Jog wheel is accidentally  
moved.  
However, if the measurement button is pressed, a  
new measurement is displayed with the same locked  
settings.  
2. To release the Jog Wheel lock, perform the same op-  
eration for the Jog Wheel lock, Hold down the Mode  
set button and ISO1 button and Offwill appear to  
indicate that the Jog Wheel lock is released.  
Reference:  
If power of the meter is turned off or auto off is activated when in the Jog Wheel locked position,  
the lock function will continue operating when the meter is turned on again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-9-  
3. Before Using  
9. Setting the Measuring and Memory button configuration  
In the custom settings mode (refer to P40), the Measuring  
button and the Memory button can be set as follows.  
1. For Incident measuring  
The Measuring button and Memory button is set in the  
standard configuration. (Described on Page 1 in Light  
Meter Parts) Please make sure that the default value  
in the Custom settings mode is set to .(Custom No.17,  
Item No. 0)  
Memory  
button  
Measuring  
button  
Configuration 1)  
2. For Reflected (Spot) measuring  
If the standard buttons configuration is inconvenient  
for spot metering, the Measuring button and Memory  
button can be switched. Set the Custom settings mode  
to Custom No. 17, Item No. 1  
Measuring  
button  
Memory  
button  
Configuration 2)  
3. For both Incident/Reflected (Spot) measuring simultaneously  
You can set the buttons configuration automatically according to light measuring method. In  
incident mode, the buttons configuration is 1), but in reflected mode, the buttons configuration  
is 2). For this setting, please set (Custom settings mode No. 17 and Item No 2).  
Incident  
Reflected  
Automatically  
switched  
Memory  
button  
Measuring  
button  
Configuration 3)  
Measuring  
button  
Memory  
button  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-10-  
4. Basic Operation  
1. Incident or reflected spot measuring  
1. To set for either incident or reflected light operation, turn the Incident / Reflected Spot Selector  
Dial on the eye piece, to the desired position ( or  
mark) until it clicks.  
Incident operation  
Reflected Spot operation  
2. When incident operation is selected, the  
mark will blink for ten seconds and when Reflected  
Spot operation is selected the mark will blink for ten seconds on the LCD.  
Incident operation  
Reflected Spot operation  
NOTE:  
Before taking measurements, always make sure that the desired measurement mode  
or ) is chosen by checking the LCD or that the Incident/Reflected Spot Selector  
Dial is clicked in proper position.  
(
Do not rotate the Spot lens ring. There is danger of damage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-11-  
4. Basic Operation  
2. Setting measuring mode  
1. Hold down the Mode button and turn the Jog wheel to  
select the desired mode. The mode switching sequence is  
shown in the chart below:  
Shutter Speed Priority mode  
Wireless Multiple Flash  
(Available light)  
Radio Triggering mode  
See page 15  
with Radio  
transmitter module  
See page 28  
Aperture Priority mode  
(Available light)  
with Radio  
transmitter module  
Wireless Flash Radio  
Triggering mode  
See page 17  
See page 28  
EV mode (Available light)  
See page 18  
with Radio  
transmitter module  
Wireless Flash channel  
Setting mode  
See page 28  
LUX, FC  
FL, cd/m2  
CINE only  
See page 34,35  
Cord Multiple Flash  
(Cumulative) mode  
Auto Reset Cordless Flash  
mode  
See page 24  
See page 22  
Cordless Multiple Flash  
(Cumulative) mode  
Cord Flash mode  
See page 21  
See page 25  
2. Modes enclosed in dotted lines  
(See page 40)  
can only be selected with custom setting.  
3. Modes enclosed in  
lines can only be selected with L-758DR. For L-758D and L-758CINE,  
they can be selected when Optional Radio Transmitter Module is installed. (See page 28)  
4. In addition to exposure reading, L-758CINE displays FC or LUX in incident light mode, and FL  
or cd/m2 in reflected light mode.(See page 34)  
Reference:  
Available light is continuous light like natural light (sunlight) or tungsten lamps and florescent  
lamps like pulsing light sources.  
Flash light is a brief, intense burst of light made by such as electronic flash units or flash bulbs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-12-  
4. Basic Operation  
3. Incident Measurement Mode  
Incident light measuring is the measurement method that  
employs either the Lumisphere or Lumidisc functions.  
Measurements should be with the Lumisphere aimed  
towards the camera direction from the subject position.  
1. You can select extended or retracted lumisphere measuring positions by rotating the Lumisphere  
retracting ring (clockwise or counter-clockwise) until it clicks into position.  
Retracted Lumisphere  
(Lumidisc)  
Extended Lumisphere  
2. When the Lumisphere is extended. (3-D Light Measurement)  
This is used to measure people, buildings, and other three dimensional objects.  
Measurements are basically made by the method of measuring with the lumisphere aimed in  
the camera direction (more precisely, in the direction of the lens axis) at the position of the  
subject.  
3. When the Lumisphere is retracted (flat diffuser function)  
This is used to measure manuscripts, paintings or other flat copy. It can also be used for Contrast  
function (see page 32) or measuring illumination (see page 34).  
NOTE:  
If the light meter is used with the Lumisphere retracting ring in a middle position, distributed  
light quality will change, and suitable measurements cannot be made.  
Do not push the Lumisphere down with your finger or hand. Always use the Lumisphere  
retracting ring.  
If the lumisphere becomes soiled, wipe it with a soft, dry cloth. Organic solutions (paint  
thinner, benzene, etc.) must not be used under any circumstances.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-13-  
4. Basic Operation  
4. Reflected Measurement Mode (spot metering)  
This method measures the brightness (luminance) of the  
light reflected from the subject. It is useful for distant objects  
such as landscapes, when you cannot go to the position  
of the subject, or for metering subjects that generate light  
(neon signs, etc.), highly reflective surfaces or translucent  
subjects (stained glass, etc.).  
A
1. Take the measurement by aligning the circle inside the  
viewfinder with the subject area to be measured.  
2. The black circle A in the finder indicates the measure-  
ment range. The light receiving angle is 1 degree .  
(Display in spot viewfinder)  
< Diopter Adjustment >  
Turn the eyepiece @and adjust the diopter so that the circle in the finder is clearly visible when  
you look into the finder.  
< Step-Up Ring (Lens Hood)> (optional)  
The step-up ring (30.5mm 40.5mm), available as an optional accessory, makes it possible to  
mount step-up rings and filters. This simplifies the setting of exposure without the troublesome  
correction calculation of polarizing filters, etc. (see page 52)  
The step-up ring can also be used as a lens hood to prevent lens flare and erroneous light  
measurements from glare, it also protects the spot lens from scratching, soiling, etc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-14-  
5. Measurement  
1. Measuring ambient light  
In this measurement mode, we have the choice of shutter priority mode, aperture priority mode or  
EV mode. Hold down the Mode button and turn the Jog wheel to select ambient measurement  
mode  
.
1-1 Shutter Speed Priority mode  
1. Hold down the Mode button and turn the Jog  
wheel to select Shutter Speed Priority mode  
.
2. Turn the Jog wheel to set the desired shutter  
speed.  
3. Press the Measuring button to take a  
measurement. Release the Measuring button to  
complete the measurement. The measured value  
(aperture value) at that time will be displayed.  
Set  
shutter speed  
Measured f stop  
value  
While pressing the Measuring button, the meter  
measures continuously until it is released.  
1/10  
f stop  
Measured f stop(blinking)  
Reference:  
It is possible to switch between full, 1/2 and 1/3 shutter speeds with custom setting  
(see page 36).  
You can set shutter speeds from 30 minutes to 1/8000 seconds. After 1/8000 the shutter  
speeds of 1/200 and 1/400 can be set.  
After taking a measurement, the F stop value corresponding to the shutter speed is  
displayed. The measured F stop value automatically corresponds to the shutter speed  
if the shutter speed is changed by rotating Jog wheel.  
The L-758DR/758D displays the measured aperture value in either full or 1/3 stop  
increments on the analog scale from f/0.7 to 90, while L-758 CINE displays it in either  
full or 1/3 stop increments on the analog scale from F0.5 to F64.  
You can select aperture scale or EV scale by holding MODE button and pressing AVE.  
/ EV.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-15-  
5. Measurement  
• “E.u(Exposure under) or E.o(Exposure over) appears when the combination of shutter  
speed and aperture is outside the display range.  
When E.O (Exposure Over) is displayed,it indicates that the measured exposure is outside  
the display range, changing the shutter speed to a faster setting with the Jog wheel will allow  
you to find a combination of proper aperture and shutter speed.  
When E.U (Exposure Under) is displayed, it indicates that the measured exposure is outside  
the display range, changing the shutter speed to a slower shutter speed with the Jog wheel  
will allow you to find a combination of proper aperture and shutter speed.  
If the E.uor E.oreadout blinks, this indicates that the light level is beyond the measurement  
range of the light meter. Adjust lighting in this case.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-16-  
5. Measurement  
1-2 Aperture Priority mode  
1. Hold down the Mode button and turn the Jog wheel to  
select aperture priority mode  
.
2. Turn the Jog wheel to set the desired f stop  
value.  
Measured value  
(shutter speed)  
3. Press the Measuring button to take  
a
measurement.  
Set f stop value  
Release the Measuring button to complete the  
measurement. The measured value (shutter  
speed) at the time will be displayed.  
While pressing the Measuring button, the  
meter measures continuously until it is  
released.  
1/10  
shutter  
speed  
Measured shutter speed(blinking)  
Reference:  
It is possible to switch between full, 1/2 or 1/3 F stop values with the custom setting mode  
(see page 40).  
You can set aperture from 0.5 to F161. Please note that in 1/3 stop increments F0.56 is  
displayed as  
and F0.63 is displayed as  
.
EV scale appears on the analog scale. (Shutter speed scale is not displayed.) For details,  
please see page 48.  
After measurement, the shutter speed corresponding to the F stop is displayed when the  
F stop is changed with Jog Wheel.  
Readings outside the display range or beyond the measuring range are similar to the  
previous instruction (see page 16).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-17-  
5. Measurement  
1-3 EV mode  
1. To activate EV mode, please set Custom setting  
no.5 and Item no.1. (See page 40)  
2. Hold down the Mode button and turn the Jog  
wheel to select EV mode  
.
Shutter  
speed  
3. Press the Measuring button to take a  
measurement. Release the Measuring button to  
complete the measurement. The measured value  
(EV=Exposure Value) at that time will be displayed.  
At the same time, the shutter speed will be  
displayed in the digital display area, and the  
corresponding f stop will be displayed on the analog  
scale.  
While pressing the measuring button, the meter  
measures continuously until it is released.  
EV value  
f stop(blinking)  
Reference:  
EV (Exposure Value) is the reading that logarithmically expresses the constant quantity of  
light combined from the shutter speed and aperture value. With 1 EV change the quantity of  
light doubles (or halves).  
To display EV mode, please set custom setting number 5 and item number 1. (See page 40)  
Readings outside the display range or beyond the measuring range are similar to the previous  
instruction (see page 16).  
You can select aperture scale or EV scale by holding MODE button and pressing AVE. / ⊿  
EV.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-18-  
5. Measurement  
1-4 Cinematography  
1. Hold down the Mode button and turn the Jog wheel  
to select ambient light shutter speed priority mode  
.
2. Turn the Jog wheel to select the Cine Speed for the  
camera that will be used.  
Cine Speed are displayed after 1/8000, 1/200, 1/400 and  
the unit is in frames per second (f/s).  
[L-758DR/758D]  
The following Cine Speeds will be displayed:  
2, 3, 4, 6, 8, 12, 16, 18, 24, 25, 30, 32, 36, 40, 48, 50, 60,  
64, 72, 96, 120, 128, 150, 200, 240, 256, 300 and 360 f/s.  
[L-758CINE]  
The following Cine Speeds will be displayed:  
1, 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 24, 25, 30, 32, 36,  
40, 48, 50, 60, 64, 72, 75, 90, 96, 100, 120, 125, 128,  
150,180, 200, 240, 250, 256, 300, 360, 375, 500, 625,  
750 and 1000 f/s.  
3. The shutter angle that these speeds are based on, is  
180 degrees. For other angles make the following ISO  
sensitivity corrections (L-758DR/758D only).  
Amount of ISO sensitivity  
Shutter angle  
correction  
160 degrees  
-1/3  
220 degrees  
+1/3  
* Example of correction value  
-1/3: Decrease ISO sensitivity by 1/3 stop, example: ISO 80 -1/3 stop = ISO 64  
+1/3: Increase ISO sensitivity by 1/3 stop, example: ISO 80 +1/3 stop = ISO 100  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-19-  
5. Measurement  
4. Setting the shutter angle (L-758CINE only).  
It is possible to set the shutter angle by turning the Jog wheel while pressing Mode  
button and ISO2 button .  
Note:  
Shutter angle: The angle can be set in the range of 1°to 10° (in 1° steps), 15° - 270° (in  
5° steps) as well as, 12°, 17°, 22°, 144° and 172°.  
"  
" is displayed continuously on the LCD display if the shutter angle is set to any  
value other than 180°.  
Press both the Mode button and ISO2 button to confirm the shutter angle since it is not  
displayed.  
Reference:  
This setting is only valid when the shutter speed is set to display cine speed (f/s).  
Measured f stopvalue  
Set shutter speed  
5. Press the Measuring button to take a  
measurement. Release the Measuring button to  
complete the measurement. The measured value  
(f stop value) will be displayed. While pressing  
the measuring button, the meter measures  
continuously until it is released.  
1/10  
f stop  
Measured f stop  
on analog display  
Reference:  
You can select aperture scale or EV scale by holding Mode button and pressing AVE./ EV.  
The L-758DR/758D displays the measured aperture value in either full or 1/3 stop increments  
on the analog scale from f/0.7 to 90, while L-758CINE displays it in either full or 1/3 stop  
increments on the analog scale from F0.5 to F64.  
Readings outside the display range or beyond the measuring range are similar to the previous  
instruction (see page 16).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-20-  
5. Measurement  
2. Measuring electronic flash  
This method of measurement can be done in the following modes; with cord, without cord, and  
Wireless flash radio triggering mode (cumulative or non-cumulative). When Measuring flash light,  
the shutter speed and F stop value (value combining ambient light and flash light: total amount of  
light) are displayed. The ambient light and flash light are each displayed as separate values together  
with the total amount of light on the analog scale. In addition, the ratio of flash light to the total  
amount of light is displayed at that time as a value in 10% steps.The flash reading is displayed as a  
blinking mark above the analog scale. (See page 27 for details)  
2-1 Cord Flash mode  
Connect the meter to the flash with a synchro cord. Be sure to replace Synchro terminal cap  
@after your measurement.  
1. Connect the flash synchro cord to the Synchro  
terminal ion the light meter.  
A
EV  
˘
VE./  
A
c
2
O
d
IS  
b
Y
R
POWER  
O
M
E
b
M
1
O
S
I
E
D
E
N
O
O
O
T
.
M
D
I
M
2. Hold down the Mode button and turn the Jog  
wheel to select cord flash mode  
.
3. Turn the Jog wheel to set shutter speed. When set-  
ting shutter speed, first check the settings to con-  
firm that they correspond to the settings on the cam-  
era.  
Percentage of flash in  
total exposure  
4. Press the Measuring button to trigger the flash.  
The measured value (f stop value) will be displayed.  
Set shutter speed  
Measured f stop value  
1/10  
f stop  
Ambient  
Flash  
Measured f stop value  
(total exposure)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-21-  
5. Measurement  
WARNING:  
To avoid a danger of choking, please place Synchro terminal cap in a location where an  
infant cannot reach and accidentally swallow it.  
CAUTION:  
There is danger of electric shock if the meter is handled with wet hands, during rain, in  
areas splashed by water or where there is a lot of moisture. Under such conditions, it is  
recommended that you use the meter in the cordless flash mode or Wireless flash radio  
triggering mode, and keep the Synchro terminal cap in place.  
NOTE:  
The electronic flash unit may trigger when you connect the Synchro cord or operate the  
Power button.  
Triggering voltage is 2.0 to 400 volts. Below 2.0V, trigger flash with the cordless flash  
mode (see page 22) or wireless flash radio triggering mode (see page 28), not with  
synchro cord.  
If you measure flashbulb, be sure to cheek the synchronized range and set the proper  
shutter speed.  
Reference:  
It is possible to switch the shutter speed between full, 1/2 and 1/3 stops by custom setting  
(See page 40).  
The shutter speed can be set from 30 minutes to 1/1000 of a second. After 1/1000 sec, the  
meter can be set at the following intermediate speeds: 1/75, 1/80,1/90, 1/100, 1/200, or  
1/400.  
If the ISO sensitivity is changed after the measurement is taken, the new converted  
measured value (f stop value) will be displayed.  
After measurement, the F stop value corresponding to the shutter speed is displayed  
when the shutter speed is changed with Jog Wheel.  
Readings outside the display range or beyond the measuring range are similar to the  
previous instruction (see page 16).  
You can select aperture scale or EV scale by holding Mode button and pressing AVE. /⊿  
EV.  
2-2 Auto-reset cordless flash mode  
Measurements are made by the meter receiving the light from the flash. This measurement  
mode is used when the Synchro cord will not reach because of the distance between the flash  
and meter or when use of the Synchro cord is inconvenient.  
1. Hold down the Mode button and turn the Jog  
wheel to set Auto-reset Cordless Flash mode  
.
2. Turn the Jog wheel to set shutter speed. When  
setting shutter speed, first check the settings to  
confirm that they correspond to the settings  
available on the camera (camera flash  
synchronization).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-22-  
5. Measurement  
3. When the Measuring button is pressed, the  
mode mark will blink and the meter is ready to  
measure. The ready to measure mode will continue  
for approximately 90 seconds.  
During this time, trigger the flash to make a  
measurement.  
Percentage of  
flash in total  
exposure  
Set shutter speed  
4. If the 90 second period is exceeded and the blinking  
mark stops, press the Measuring button again to  
return to ready to measure status.  
Measured f stop  
1/10  
f stop  
Ambient  
Flash  
Measured f stop  
(total exposure)  
5. When the light from the flash is received, the measured value (f stop) is displayed. Even  
after measurement, the mode mark continues to blink and the meter is in ready state  
and a new measurement can be made. (Auto-reset function)  
NOTES:  
When firing a flash, if the flash brightness is 8EV lower than the ambient light, the meter  
may fail to detect the light. In this case, make measurements using the cord flash mode  
(see page 21).  
Rapid start fluorescent lamps and special lighting are sometimes mistaken for flash, and  
accidentally measured. In this case, make measurements using the cord flash mode (see  
page 21).  
The waveform of flashbulb have a slight slope and there is a possibility that light meter  
cannot recognize the flashbulb in Cordless flash mode. In this case, be sure to take  
measurement in Cord flash mode (see page 21).  
Reference:  
After measurement, the F stop value corresponding to the shutter speed is displayed when  
the shutter speed is changed.  
Setting the shutter speed is similar to the previous instruction. (see page 21) of Cord flash  
modeof section 2-1.  
A new converted value is displayed when the ISO sensitivity is changed after taking the  
measurement.  
Readings outside the display range or beyond the measuring range are similar to the previous  
instruction. (see page 16) of Shutter speed priority modeof section 1-1.  
You can select aperture scale or EV scale by holding Mode button and pressing AVE. /EV  
button.  
The meters tripod socket permits mounting it to a tripod or light stand and placing it strategically  
when using cordless flash mode.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-23-  
5. Measurement  
2-3 Cord multiple flash (cumulative) mode  
These measurements are used when the light generated by the flash is inadequate for proper  
exposure. The repeated flash pops can be accumulated until the desired aperture is displayed.  
The cumulative number is infinite. Only one digit is displayed if the cumulative number is ten or  
more. Display returns 0 (0=10, 1=11, 2=12, etc.)  
To activate Multiple cumulative mode, please set  
custom setting no.6 and Item no.1.  
1. Hold down the Mode button and turn the Jog  
wheel to select cord multiple flash (cumulative)  
mode  
.
2. Turn the Jog wheel to set shutter speed. When setting shutter speed, first check the settings  
to confirm that they correspond to the settings available on the camera.  
3. Connect the Flash synchro cord to the meter's  
synchro terminal .  
4. Press the Measuring button to trigger a flash. The measured f stop value at that time will  
be displayed. Each time this is repeated, the accumulated f stop value and the number of  
cumulative flashes is displayed.  
Percentage of flash in  
total exposure  
1/10 f stop  
Number of  
cumulative flashes  
Measured f stop  
Set shutter speed  
Measured f stop  
(total exposure)  
1st. time  
2nd. time  
3rd. time  
5. To clear the cumulative value, press M. CLEAR button @  
3
or switch to another mode by  
turning the Jog wheel while pressing the Mode button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-24-  
5. Measurement  
CAUTION:  
There is danger of electric shock if the meter is handled with wet hands, during rain, in  
areas splashed by water or where there is a lot of moisture.  
Under such conditions, it is recommended that you use the meter in the cordless flash  
mode, or wireless flash radio triggering mode and keep the Synchro terminal cap in place.  
NOTE:  
The flash unit may flash when you connect the Synchro cord or operate the Power button.  
When firing a flash to take measurements, check the camera's synchronizing range and  
set the proper shutter speed.  
For flash units with low electric trigger voltage, the flash may not fire. In this case, make  
measurements in cordless multiple flash mode (see page 25) or wireless multiple flash  
radio triggering mode (see page 29).  
EV scale cannot display in flash cumulative mode.  
Reference:  
Setting the shutter speed is similar to the previous instruction (see page 22).  
Readings outside the display range or beyond the measuring range are similar to the previous  
instruction (see page 16) of Shutter speed priority modeof section 1-1.  
If the ISO sensitivity film speed is changed after the measurement is taken, the new converted  
measured value (f stop value) will be displayed.  
2-4 Cordless multiple flash (cumulative) mode  
These measurements are used when the light generated by the flash is inadequate for proper  
exposure. The repeated flash pops can be accumulated until the desired aperture is displayed.  
The cumulative number is infinite. Only one digit is displayed if the cumulative number is ten or  
more. Display returns 0 (0=10, 1=11, 2=12 etc.)  
To activate Multiple cumulative mode, please set Custom setting no.6 and Item no.1.  
1. Hold down the Mode button and turn the Jog  
wheel to select flash measurement cordless  
multiple flash (cumulative) mode  
.
Turn the Jog wheel to set shutter speed. When  
setting shutter speed, first check the settings to  
confirm that they correspond to the settings  
available on the camera.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-25-  
5. Measurement  
2. When the light from the flash is received, the measured value (f stop) is displayed. Each  
time this is repeated, the accumulated value for the aperture and the number of cumulative  
flashes is displayed.  
Percentage of flash in  
total exposure  
Measured f stop  
Number of  
cumulative flashes  
1/10 f stop  
Set  
Measured f stop  
(total exposure)  
shutter speed  
1st. time  
2nd. time  
3rd. time  
3. The ready to measure mode will be displayed for approximately 90 seconds. If the 90  
second period is exceeded and the blinking mark stops, press the Measuring button ⑭  
again. The measured value (f stop) of the previous time reverts to 0 and the meter is in  
ready to measure mode.  
NOTE:  
When firing a flash, if the flash brightness is 8 EV lower than the ambient light, the  
meter may fail to detect the light. In this case, make measurements using the flash with  
cord multiple flash (cumulative) mode (see page 24) or wireless multiple flash radio  
triggering mode (see page 29).  
Rapid start fluorescent lamps and special lighting are sometimes mistaken for flash,  
and accidentally measured. In this case, make measurements using the flash with  
cord multiple flash (cumulative) mode (see page 24) or wireless multiple flash radio  
triggering mode (see page 29).  
Waveform of flashbulb is gentle slope and there is a possibility that light meter cannot  
recognize the flashbulb in Cordless flash mode. In this case, be sure to take  
measurement in cord multiple flash (cumulative) mode (see page 24) or wireless multiple  
flash radio triggering mode (see page 29).  
EV scale cannot display in flash cumulative mode.  
Reference:  
Setting the shutter speed is similar to the previous instruction (see page 22).  
Readings outside the display range or beyond the measuring range are similar to  
the previous instruction. (See page 16) of Shutter speed priority modeof section 1-  
1.  
If the ISO sensitivity is changed after the measurement is taken, the new converted  
measured value (f stop value) will be displayed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-26-  
5. Measurement  
2-5 Flash analyzing function  
When measuring flash light, the shutter speed and F stop value (combining ambient light and  
flash light: total amount of light) are displayed on the LCD screen and the ambient light and  
flash light are each displayed as separate values along with the total amount of light (combined  
flash and ambinent) on the analog scale. In addition, the ratio of flash light to the total amount  
of light is displayed as a percentage (in 10% steps) at the sametime. The ratio of flash to the  
total amount of light is useful when a desired flash to ambient lighting ratio is needed.  
< Example >  
Percentage of flash in  
total exposure  
Under certain conditions, if the flash light output is  
60% and the available light output is 40%, the LCD  
screen will display the flash measured value on the  
analog scale with a faster blinking icon than the total  
exposure blinking icon.  
1. To emphasize the ambient light (to create a more  
natural lighting condition) increase the ratio of  
ambient light,(use the Jog wheel )by changing  
the shutter speed to a slower setting.The ratio of  
flash light in the total exposure will be reduced (as  
shown in the diagram to the right - 20%).The  
analog scale also shows the ambient output to be  
about 2.5 stops higher than the flash light output.As  
a result,images will exhibit a natural lighting quality  
with flash filled shadows without an over powering  
presence of flash.  
Ambient  
Flash  
Measured f stop  
(total exposure)  
2. To reduce the effect of ambient light decrease the  
ratio of ambient light, (use the Jog wheel) by  
changing the shutter speed to a faster setting. The  
ratio of flash in the total exposure will be increased  
(as shown in the diagram to the right 80%) The  
analog scale also shows the flash light output to  
be about 1.5 stops higher than the ambient light  
output.  
(Display in spot viewfinder)  
Reference:  
Slower shutter speeds allow more available light to reach the film or digital camera sensor,  
and faster shutter speeds reduce the amount of available reaching the film or sensor.  
The settings above are made by adjusting the ambient light by the shutter speed. It is also  
possible to modify the ratio by adjusting the flash light (when changing the distance between  
the flash and the subject or when changing the amount of light of the flash). When using  
this method, re-measure each time the flash light is adjusted.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-27-  
5. Measurement  
2-6 Wireless Flash Radio Triggering  
With the Radio Transmitter module plugged into the meters radio socket and a Receiver or  
Transceiver (PocketWizard®) connected to one or more electronic flash units, the meter provides  
a convenient system that enables one person working alone to measure flash output without  
the need of a sync cord. Pressing the Measuring button simultaneously triggers the flash and  
measures the flash output simultaneously.  
The L-758DR/758D/758CINE has 32 triggering channels with the RT-32 radio triggering module  
(built-in for L-758DR, optional for L-758D/758CINE). Channels 1-16 provide single triggering,  
while channels 17-32 offer Selective Quad-Triggering control. Selecting one of the Quad-  
Triggering channels (17-32) provides control of up to four zones of lighting indicated as a Zone  
letter (A, B, C and D). Selecting or deselecting a zone is quick and easy with the Quad-Triggering  
buttons (A,B, C or D). In order to trigger a flash units set for Quad-Triggering, the electronic  
flash unit must be connected to a PocketWizard MultiMax or a n electronic flash that already  
has a PocketWizard built-in. The PocketWizard Plus or Plus II can be triggered by the  
L-758DR using channels 1-4.  
< Example with optional 32 channels receiver >  
For L-758D/758CINE: Open the battery compartment cover , remove connector cover @  
and set the RT-32 Radio Transmitter module (optional) by aligning the connector with the pins.  
5
1. Select the Wireless Flash Radio Triggering setting  
mode by using the Jog wheel while pressing  
the Mode button .  
2. The set channel number will blink, turn the Jog wheel to select the channel desired.  
3. In the Channel setting mode, chand channel number appear on the upper left side of the  
LCD. The channel numbers (1 to 16 or 17 to 32) will appear in the F-stop display area.  
When the channel number is set to 17 - 32, Quad-Triggering zones (A, b, c and d) are  
displayed in the T (shutter speed) display area. In the absence of a Quad-Triggering setting  
(A,b,c or d), a -will appears in it's place.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-28-  
5. Measurement  
4. In the Quad-Triggering zone setting, after the channel is set to 17 to 32, the assigned  
buttons below are pressed. Pressing each of the buttons activates or deactivates the Quad-  
Triggering zone (A, b, c or d). When a Quad-Triggering zone is activated, the corresponding  
Quad-Triggering zone letter appears on the display. If a Quad-Triggering zone is deactivated,  
a -" is displayed in its place.  
Each assigned button enables to set  
Quad-triggering zone directly.  
ISO 1  
ISO 2  
MID.TONE  
M.CLEAR  
A”  
b”  
c”  
d”  
CAUTION:  
It is not possible to activate Quad-Triggering control without first selecting a channel 17-  
32, and a Quad-Triggering zone (A, b, c or d).  
To prevent damage due to static electricity, release any static electricity from your body by  
touching a metal object nearby (door knob, aluminum window frame, etc.) before touching  
the radio transmitter module.  
5. Upon setting the channel and Quad-Triggering zones,press the Measuring button to  
enter your settings. The display will automatically go to the main LCD screen and Wireless  
Flash Radio Triggering mode will be activated or rotate Jog wheel to set wireless flash  
radio triggering mode or wireless multiple flash radio triggering mode.  
6. Confirm that the meter and the radio Receiver or Transceiver are set to the same channel  
number. The flash unit will fire and measure the light output when the measuring button on  
the meter is pressed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-29-  
5. Measurement  
Reference:  
Refer to the radio Receiver or Transceiver instruction manual for the recommended operating  
method.  
Maximum distance of the radio flash triggering system can vary depending on the placement  
of the remote Receiver or Transceiver, direction of the radios antenna, distance from a  
large body of water or concrete wall and other possible factors.  
1. Confirm the range between the meter (transmitter) and Receiver or Transceiver.  
2. Place the meter and Receiver or Transceiver away from large metal objects, concrete,  
objects, large moisture content (both people and trees fall into the category) and so  
forth.  
3. Secure the radio Receiver or Transceiver in place by using Velcro tape or a 1/4-20  
mounting screw. Be sure that the entire length of the Receiver or Transmitter antenna  
is higher than the flash pack. Avoid contact between the Receiver or Transceiver  
antenna and metal objects at all times.  
4. Depending on the location, there may be cases when the Receiver or Transceiver is  
incapable of receiving any radio signals whatsoever. There are several possible causes  
for this such as radio signals reflected off of nearby objects. This can generally be  
resolved by shifting the meter (Transmitter) or the Receiver or Transceiver slightly in  
one direction or another. In addition, confirm that the Receiver or Transceiver is not  
placed behind objects that readily absorb or deflect radio signals such concrete, metal,  
low hills, etc.  
NOTE:  
The Wireless flash triggering system may be used only in countries where a permit for the  
control frequency has been issued by the government office in charge. There are several  
kinds of frequencies in the world, and we recommend you check if your transmitter(s) and  
receiver(s) or Transcevers are compatible with each other.  
L-758D or L-758CINE  
(FCC & IC version)  
RT-32FCC  
(for FCC & IC)  
Sticker on the back  
indicates Use RT-  
32FCC for radio  
transmitter module”  
No compatible  
L-758D or L-758CINE  
(CE version)  
RT-32CE  
(for CE)  
Sticker on the back  
indicates CE”  
Be sure to purchase either RT-32FCC or RT-32CE module according to your light meters  
destination. Old RT-32 module cannot be used with L-758D or L-758CINE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-30-  
6. Advanced Functions  
1. Memory function  
This meter can store up to nine measured values in memory for incident light and reflected light  
simultaneously. This feature can be used in the following modes;  
Ambient light : shutter speed priority, aperture priority or EV mode.  
Electronic Flash light : cord, cordless or wireless flash radio triggering mode.  
1. Press the Measuring button and take a mea-  
surement. The Current measured value on the ana-  
log scale will blink.  
2. Press the Memory button and store the mea-  
sured value in memory, and the memorized value  
on the analog scale will stop blinking.  
The number of values in memory is displayed on  
Memory button  
the LCD. The memorized value is displayed on the  
analog scale. By repeating this operation, up to nine  
values can be stored in memory.  
Number of memorized value  
Set shuttter speed  
3. To clear the memory, press the memory clear but-  
ton @ or switch to another measurement mode.  
3
Reference:  
• When pressing Memory clear button @  
3
once,  
1/10  
f stop  
the last memorized value is cleared. If you want  
to clear all memorized values, please hold  
down the Mode button and press the  
Memory clear button.  
Measured f stop  
Memorized  
f stop  
4. Memory Recall  
To enter Memory recall mode, hold down the Mode button and press the Memory button, and  
the "M" icon and number of stored measurements will blink. Rotate Jog wheel to recall memo-  
rized value. To exit Memory recall mode, hold down the Mode button and press the Memory  
button again, and "M" icon and number of stored measurements will stop blinking.  
Reference:  
• During Memory recall mode, when you press Memory clear button, the currently recalled  
value is cleared.  
NOTE:  
The memory function cannot be used in “Multiple flash (cumulative) mode.”  
Measured values for ten times or more measurements will be displayed but cannot be  
stored in memory.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-31-  
6. Advanced Functions  
2. Averaging function  
This function displays the average of up to nine of the values in memory.  
1. Press the Measuring button and take a meas-  
urement. Current measured value on the analog  
scale will blink.  
2. Press the Memory button and store the measured  
value in memory, and memorized value on the  
analog scale stops blinking.  
Memory button  
3. When the AVE./ EV button is pressed, an  
averaged value for up to nine measurements will  
be displayed on the LCD. The values in memory  
and the averaged value are displayed on the analog  
scale (The averaged value blinks). An “A” appears  
in LCD to indicate this is an average.  
Averaging indicator  
Averaged f stop  
Number of memorized  
value  
4. The average mode can be canceled by pressing  
the AVE./ EV button.  
1/10  
f stop  
Reference:  
• When the EV scale is selected, the averaged  
exposure value will be displayed in the center  
of the scale.  
Averaged f stop  
Memorized  
f stop  
Set shutter speed  
3. Contrast function  
This function is useful for evaluating studio lighting and checking the evenness of the lighting set-up  
across the subject area.  
Take a measured value at a certain point as a standard value. The difference between the standard  
value and a new measured value is displayed in EV and the measurements are displayed on the  
analog scale.  
Example of adjusting lights using Contrast function in shutter speed priority mode (incident light).  
1. Turn the Lumisphere retracting ring to lower it to the  
(retracted) mark position.  
-32-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Advanced Functions  
2. Turn any secondary light source off. Point the  
Lumisphere toward the main light source, from the  
position of the subject and take a measurement. Press  
the Memory button and store the value in memory.  
3. Press the AVE./ EV button and display the “A”mark  
Memory button  
on the LCD indicating a standard value.  
Indicator of reading  
Set shutter speed  
4. Turn the main lighting off. Now, point the Lumisphere  
toward the secondary light source. While pressing and  
holding the Measuring button , the indicated  
difference between the main and secondary light  
source is displayed in EV. At the same time, the  
standard value and a new measured value are  
displayed on the analog scale.  
Contrast in  
EV  
Memorized  
f stop value  
f stop value  
being measured  
Contrast ratio  
2 : 1  
EV difference of EV value  
1
1.5  
2
3 : 1  
4 : 1  
3
8 : 1  
4
16 : 1  
5. The Standard value can be cleared by pressing the Memory clear button @ , or AVE./ EV  
3
button.  
Reference:  
To determine exposure after adjusting lights, turn both main and secondary light sources  
on, raise the Lumisphere to the mark position, then take a reading with the Lumisphere  
aimed in the direction of camera's lens axis in incident light.  
• This function can also be used for reflected light.  
You can select aperture scale or latitude scale by holding Mode button and pressing  
AVE. / EV.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-33-  
6. Advanced Functions  
4. How to use an incident illuminance (LUX or FC) meter (L-758DR/758D)  
1. Turn the Lumisphere retracting ring to lower it to the  
(retracted) mark position.  
2. Make sure that any compensation Exposure/Calibration  
compensation: see page 36 & 37, Compensation of  
camera exposure profile: see page 46 is canceled.  
3. Set the meter to EV mode and ISO 100.  
4. Place the meter parallel to the subject and take a  
measurement.  
5. The measured EV can be converted to find the  
brightness level with the conversion table below.  
* EV value Lux conversion table  
Decimal places  
Decimal places  
0
0.5  
1800  
3600  
7200  
14000  
29000  
0
0.5  
EV  
EV  
-2  
-1  
0
1
2
3
4
5
6
9
0.63  
1.3  
2.5  
5.0  
10  
20  
40  
80  
0.88  
1.8  
3.5  
7.1  
14  
28  
57  
110  
230  
450  
910  
1300  
2600  
5100  
10000  
20000  
41000  
82000  
160000  
330000  
660000  
1300000  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
58000  
120000  
230000  
460000  
930000  
1900000  
160  
320  
640  
7
8
* EV value Foot candle (FC) conversion table  
Decimal places  
Decimal places  
0
0.5  
0
0.5  
EV  
EV  
-2  
-1  
0
1
2
3
4
5
6
9
0.06  
0.12  
0.23  
0.46  
0.93  
1.9  
3.7  
7.4  
15  
30  
0.08  
0.16  
0.33  
0.66  
1.3  
2.6  
5.3  
11  
120  
240  
480  
170  
340  
670  
1300  
2700  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
950  
1900  
3800  
7600  
15000  
30000  
61000  
120000  
5400  
11000  
22000  
43000  
86000  
170000  
21  
42  
84  
7
8
59  
Reference:  
L-758CINE can read LUX or FC directly when the custom setting function is used (refer to  
page 40).  
-34-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Advanced Functions  
5. How to use a reflected luminance (cd/m2 or FL) meter (L-758DR/758D)  
1. Exposure/Calibration compensation: see page 36 & 37, Compensation of camera exposure  
profile: see page 46.  
2. Set the meter to EV mode and ISO 100.  
3. Set meter to spot reading for reflected light.  
Take the measurement by looking through the finder and aligning so the subject that will be  
measured is inside the circle.  
4. The measured EV can be converted to find the brightness level with the conversion table below.  
* EV value cd/m2 conversion table  
Decimal places  
Decimal places  
0
0.5  
360  
720  
1400  
2900  
5800  
12000  
23000  
46000  
93000  
0
0.5  
EV  
EV  
11  
12  
13  
14  
15  
16  
17  
18  
19  
1
2
3
4
5
6
7
8
9
0.35  
0.7  
1.4  
2.8  
6
11  
23  
45  
91  
0.25  
0.5  
1
2
4
260  
510  
1000  
2000  
4100  
8200  
16000  
33000  
66000  
8
16  
32  
64  
130  
10  
180  
* EV value Foot-lambert (FL)conversion table  
Decimal places  
Decimal places  
0
0.5  
0
0.5  
EV  
EV  
0.073  
0.15  
0.30  
0.60  
1.2  
2.3  
4.7  
9.3  
19  
0.10  
0.20  
0.40  
0.80  
1.7  
3.3  
6.6  
13  
11  
12  
13  
14  
15  
16  
17  
18  
19  
110  
210  
420  
1
2
3
4
5
6
7
8
9
75  
150  
300  
850  
600  
1700  
3400  
7000  
14000  
27000  
1200  
2400  
4800  
9000  
19000  
26  
37  
10  
53  
Reference:  
L-758CINE can read cd/m2 or FL directly when the custom setting function is used (refer  
to page 40).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-35-  
6. Advanced Functions  
6. How to use the Exposure compensation function  
Exposure compensation can be made in precise 1/10 step increments in a +/- 9.9 EV range. Exposure  
compensation may be necessary when compensation for filters, bellows, extension tube, etc is  
required.  
1. Set the measurement mode (incident light, reflected light) for the desired compensation. You  
can make calibration compensation independently for both incident, and reflected light. It is not  
possible to switch between measurement modes if the setting is not completed.  
2. Making a plus compensation will increase the  
exposure. Hold the ISO1 button and the ISO 2 button  
and turn the Jog wheel counter clockwise. The  
will appear in the upper section of the LCD screen.  
The compensation will change in +0.1 EV steps up to  
+9.9.  
3. Making a minus compensation will decrease the  
exposure. Hold the ISO1 button and the ISO 2 button  
and turn the Jog wheel clockwise.  
The  
will appear in the upper section of the LCD  
screen. The compensation will change in -0.1 EV steps  
up to -9.9.  
NOTE:  
When making compensations, be sure that it satisfies your needs based on the results  
of your digital camera sensor or film be used.  
While incident and reflected light can be set independently, be aware that both ambient  
light and flash exposure are corrected uniformly.  
Compensation effects every mode of the meter.  
If recalibration has been made for specific purpose do not forget to return to original  
zero settings.  
Reference:  
When compensation is activate, a plus ( ) or minus ( ) sign as well as the amount of  
compensation is displayed continuously on the LCD. You can set custom settings so that  
a plus ( ) or minus ( ) sign as well as the amount of compensation doesn’t appear on the  
LCD. (See page 40)  
You can also set custom setting so that making a plus compensation results in a decreased  
exposure (increasing the value of the aperture or shutter speed value) and making a  
minus compensation results in and increased exposure (decreasing the value of the  
aperture or shutter speed).  
-36-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Advanced Functions  
7. How to use Calibration compensation function  
Calibration compensation can be made in precise 1/10 step increments in a +/- 1.0 EV. It provides  
the ability to match exposure measurements with meters to meters, correct exposure for special  
requirements, adjusts for film or digital cameras,etc.  
1. Set the measurement mode (incident light, reflected light) for the desired compensation. You  
can make calibration compensation independently for both incident, and reflected light. It is not  
possible to switch between measurement modes if the setting is not completed.  
2. To enter the calibration setting of the meter it must first  
be turned off. Press the power button on while holding  
down the ISO1 and ISO2 buttons simultaneously. You  
can release the power button, however please keep  
pressing both ISO1 and ISO2 buttons; the screen will  
display CAL 0.0 (for calibration).  
3. The calibration setting can be changed by rotating the Jog wheel while pressing and holding  
down the ISO 1 and ISO 2 buttons simultaneously. A range of +/- 1.0 EV in 1/10 step increments  
is possible for calibration.  
NOTE:  
When making calibration compensations, be sure that it satisfies your needs based on  
the results of digital camera sensor or film being used.  
While incident and reflected light can be set independently, be aware that both ambient  
light and flash exposure are corrected uniformly.  
Compensation effects every mode of the meter. If recalibration has been made for  
specific purpose, do not forget to return to original zero settings.  
Reference:  
The calibration setting is not displayed on the main screen once it is set.  
You can also set custom setting so that making a plus compensation results in a decreased  
exposure (increasing the value of the aperture or shutter speed value) and making a  
minus compensation results in and increased exposure (decreasing the value of the  
aperture or shutter speed).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-37-  
6. Advanced Functions  
8. Filter compensation  
8-1 Filter compensation (1)  
It is possible to compensate for filter factor within a range of ±5.0 EV in 1/10 steps. The measurement  
corresponding to the set compensation and can be displayed while pressing ISO2 button .  
Highlight and shadow compensation values can also be enter for quick exposure metering.  
1. Select setting number 1 and item number 1 in the custom setting mode (see page 40).  
2. Set the desired compensation by turning the Jog wheel while pressing ISO2 button.  
• In case of filter compensation  
When attaching the filter with 1.0 step exposure factor to the camera, set “1.0” in ISO2 indicator  
by rotating Jog wheel while pressing ISO2 button.  
• In case of highlight measurement compensation  
When compensating plus 2 steps from highlight measurement, set “2.0” in ISO2 indicator by  
rotating Jog wheel while pressing ISO2 button.  
-38-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Advanced Functions  
8-2 Filter factor number compensation (2) (L-758CINE only)  
When using the L-758DR for Cine/Video exposures, in cine industry, it is possible to set 7 different  
frequently used types of filters.  
1. Select setting number 1 and item number 2 in the custom setting mode (see page 40).  
2. The symbol of the desired filter from among the 7 types can be selected by turning the Jog  
wheel while pressing ISO2 button .  
3. After setting filter compensation, the filter symbol and compensated F value or EV value are  
displayed while pressing ISO2 button.  
Filters, LCD Display and Corrected Value  
Filter Factor No.  
LCD display  
85  
85-  
-0.7  
ND0.3 ND0.6 ND0.9 85N3  
85N6  
A6-  
85N9  
A9-  
n3-  
-1  
n6-  
-2  
n9-  
-3  
A3-  
Compensated value (EV)  
-1.7  
-2.7  
-3.7  
(Filter factor numbers are Kodak Wratten filter numbers.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-39-  
6. Advanced Functions  
9. Custom setting function  
The following Custom Settings provide a quick and easy setup of individual meter preferences. All  
preferences are stored on a memory chip and can not be deleted, they can only be changed back to  
default settings.  
*1 1/10 stop fractions are displayed in full, 1/2 and 1/3 step increments.  
*2 Individual: LUX, FC, cd/m2 or FL  
Compound: LUX+T+F, FC+T+F, cd/m2+T+F or FL+T+F (combination)  
*3 Auto-Switching:In incident mode,Measuring/Memory buttons are standard (as they  
are),however,in reflected mode, automatically two buttons are switched.  
Reference:  
Default settings are all set to zero (0).  
-40-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Advanced Functions  
1. To enter the custom setting mode, the meter must first be turned off. Press Mode button and  
turn the power on.  
2. In the custom setting mode, ‘CS’ (custom setting) is  
displayed in the ISO display area, a setting number  
between 01-14 (L-758DR/758D) or 01-17 (L-  
758CINE) is displayed in the shutter speed display  
area and item number 0, 1, 2 or 3 is displayed in the  
aperture display area.  
Custom setting  
item no.  
Custom setting no.  
3. Turn the Jog wheel and select the desired setting  
number and the custom setting name (see page 40).  
4. The item number will change each time the Mode button is pressed.  
5. Pressing the Memory clear button @ in the custom setting mode will reset all settings to default.  
3
6. After completing the custom setting, terminate the custom setting mode by turning the power  
off. This operation will also automatically turn off the power.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-41-  
7. Camera Exposure Profiling  
1. Calibration testing for exposure profiling  
Since no two digital cameras, camera and light meter or different types of film are likely to agree on  
the same exposure, they need to be calibrated. The L-758DR (L-758D/L-758CINE) can be pro-  
grammed to match the sensitivity of film or digital camera sensor for prefect exposure control. In  
addition, since film and digital cameras have their own unique dynamic range, clipping point (expo-  
sure tolerance) and varying ISO sensitivity they need to be profiled. To ensure repeatable accurate  
and consistent measurements and to be aware of the tonal or dynamic range of a particular type of  
film or digital camera before making a photograph, the L-758DR/L-758D/L-758CINE can be  
programmed to stored, recall and display up to three different digital cameras or film types.  
Below are the following settings that can be programmed into the L-758DR/L-758D/L-758CINE.  
1. Compensation value  
Compensation value (aperture and shutter speed) can be programmed for a specific camera  
and hand-held meter. Compensation adjustment is within a +/- 5EV range in 1/10 step incre-  
ments.  
2. Clipping point (-)  
The point at which a given lighting situation (pre-exposure) has surpassed the responds level of  
a sensor or film and alerts the shooter of a under exposure situation (Pre-Exposure Warning).  
These point can be custom set from -7EV to 0EV in 1/10 increments.  
3. Dynamic range (-)  
The point at which the sensor or film has reached its maximum reproducible shadow details  
without pixel noise or grain. Dynamic range (-) adjustment is set from -7EV to 0EV in 1/10 step  
increments.  
4. Dynamic range (+)  
The point at which the sensor or film has reached its maximum reproducible highlight details  
without blooming or highlight block up. Dynamic range (+) adjustment is set from 0EV to +7EV  
in 1/10 step increments.  
5. Clipping point (+)  
The point at which a given lighting situation (pre-exposure) has surpassed the responds level of  
a sensor or film and alerts the shooter of an over exposure situation (Pre-Exposure Warning).  
These point can be custom set from 0EV to +7EV in 1/10 increments.  
-42-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Camera Exposure Profiling  
It is necessary to test the cameras sensitivity, measure the actual dynamic range and know the  
clipping points of your digital camera and/or type of film and processing used before programming  
the L-758DR (L-758D/L-758CINE) meter for Exposure Profiling. Film exposures should be evalu-  
ated by scanning the film first and then evaluating the images in a photo application software. The  
use of a transmission/reflective densitometer can also be used if film scanning is not possible or  
desired.  
Reference:  
• The dynamic range settings and the clipping point settings can be switched, if it is necessary  
to create clipping points within the dynamic range.In this case, simple enter the dynamic  
range data in the clipping point cells and the clipping points in the dynamic range cells.  
• For details, please refer to the Software Guide found on the CD-ROM included with this  
product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-43-  
7. Camera Exposure Profiling  
2. Input test target data  
There are two ways to input the result of the test target data into the light meter: 1) Sekonic Data  
Transfer Software - install application software from the included CD-ROM and connect the com-  
puter and light meter via USB, and 2) Direct Input - Manually enter the test target data directly into  
the light meter.  
2-1 Sekonic Application Software  
Data Transfer Software is included with the L-758DR, L-758D and L-758CINE. The Software  
application CD-ROM includes the Data Transfer program for Exposure Profiling, USB drivers  
and the software instruction manual. The Data Transfer program provides the following:  
* Camera calibration compensation  
* Dynamic range setting (+/-)  
* Clipping point setting (+/-)  
* Camera Exposure Profile data transfer (to the light meter from a computer via USB connec-  
tion)  
* Camera Exposure Profile data transfer (to the computer from the light meter via USB connec-  
tion)  
2-1-1 Outline of software  
1) Sekonic Data Transfer Software Exposure Profiling Program offers several choices for  
custom calibrating the L-758DR (L-758D or L-758CINE). Below is the flow chart of menu  
selections within the program.  
Cameras selection  
Light source  
• Ambient  
Measuring method  
• Incident  
• CAMERA 1  
• CAMERA 2  
• CAMERA 3  
• Flash  
• Reflected  
Contents of setting  
• Compensation value  
• Clipping point (-)  
ISO sensitivity  
ISO3  
• Dynamic range (-)  
• Dynamic range (+)  
ISO8000  
• Clipping point (+)  
2) Up to 3 cameras, 2 light sources and 2 measuring methods can be selected and set for  
custom calibration. Each camera, light source or measuring method is stored, recalled  
and displayed within the light meter's internal software, once the data has been transfer  
to it.  
3) Data can be entered into each of the setting parameters (Compensation Value, Dy-  
namic Range +/- and Clipping Point +/-) individually or by using the "Two Points Input"  
calculator. The "Two Point Input" calculator automatically computes two settings perim-  
eters and sets all values from ISO 3 to ISO 8000.  
Reference:  
-44-  
• For detailed information on Sekonic Data Transfer Software, please refer to the Software  
Guide found on the Sekonic Application Software CD-ROM included with this product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Camera Exposure Profiling  
2-2 Manual Exposure Profile Input  
It situations where it is not possible or convenient to use a computer or the Sekonic Data  
Transfer Software, Exposure Profile data can be entered into the L-758DR (L-758D or L-758CINE)  
directly. Below is the step by step process for manually entering a specific Exposure Profile.  
1) With the meter turned off,enter the Camera Expo-  
sure Profile mode by pressing the Power button  
while pressing the AVE../ EV button at  
the same time..  
2) In the Camera Exposure Profiling mode, the cur-  
rent (or preset) contents are displayed.  
3) Setting Individual Exposure Profiles (Camera 1, 2  
and 3)  
Press MID.TONE button while pressing ISO1  
button to select the desired camera exposure  
profile.  
4) Setting measuring mode  
Rotate the Jog wheel while pressing the Mode  
button to select measuring mode (ambient or  
flash including all flash mode)  
5) Setting light receiving method  
Turn the Incident/reflected spot selector dial to  
select incident or reflected light.  
6) Setting ISO sensitivity  
Rotate the Jog wheel while pressing the ISO1  
button to select ISO sensitivity.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-45-  
7. Camera Exposure Profiling  
7) Setting compensation value  
Rotate the Jog wheel while holding down ISO1  
button and ISO2 button simultaneously.  
Compensation values can be made in 1/10 step  
increments in +/-5.0EV.  
8) Setting Clipping point (-)  
Rotate the Jog wheel while pressing AVE./ ⊿  
EV button . Clipping point can be set from -7 to  
0EV in 1/10 step increments.  
9) Setting Dynamic range (-)  
Rotate the Jog wheel while pressing MID.TONE  
button . Dynamic range can be set from -7 to  
0EV in 1/10 step increments.  
10) Setting Dynamic range (+)  
Rotate the Jog wheel while pressing Memory  
clear button @3. Dynamic range can be set from 0  
to +7EV in 1/10 step increments.  
-46-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Camera Exposure Profiling  
11) Setting Clipping point (+)  
Rotate the Jog wheel while pressing ISO2 but-  
ton . Clipping point can be set from 0 to +7EV  
in 1/10 step increments.  
12) Press the Measuring button if you want to copy  
this ISO setting to all ISO setting (from ISO 3 to  
8000)  
Reference:  
To return to a previous setting, press the ISO1 button and the Memory clear button @  
simultaneously.  
3
To return to the default setting, press the Mode button and the Memory clear button @  
3
simultaneously.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-47-  
7. Camera Exposure Profiling  
3. How to use Exposure Profiling mode  
3-1 Selecting Camera Exposure Profiling  
Preset Camera Exposure Profiles (Camera 1, 2 and 3) can be recalled.  
1) Press and hold down the ISO 1 button ,while  
pressing the MID.TONE button to select the  
desired Camera profile (Camera 1, 2 or 3).  
NOTE:  
• Holding down the MID.TONE button first and  
pressing ISO1 button makes the last  
measurement value “Mid.Tone” as standard  
value. Be sure to hold the ISO1 button first and  
press the MID.TONE button to select the desired  
camera profile.  
3-2 Analog scale  
The analog scale indicates the last measured value,  
memorized, contrast, and averaged value, clipping  
point and dynamic range on the LCD. As you can see  
in the figure on the right, it is composed of four scales.  
EV scale  
Aperture scale  
Clipping and Dynamic range icons  
Value display scale  
3-2-1 Aperture scale  
The Aperture scale can be displayed in all mode except Aperture priority mode. Aperture  
values are displayed as measured values (last measured value, memorized, contrast  
and averaged value) on this scale.  
3-2-2 EV scale  
It can be displayed in all modes except mul-  
tiple flash mode.Aperture scale or EV scale  
can be switched by holding the Mode button  
and pressing the AVE./EV button .The  
EV scale can display a memorized measured  
value (ex.Incident reading) as a standard value  
(Mid.Tone), and display it on the EV scale as  
+/- 7EV from the MID.TONE in 1/3 step incre-  
ments.  
Memory button  
1) After taking a measurement by pressing the Measuring button ,pressing either the  
Memory button ,MID.TONE button or AVE./ EV button stores the measured  
value as zero in the middle of the EV scale representing the MID.TONE value. Pressing  
MID.TONE button will display a blinking “  
” on the scale. Pressing AVE./EV button  
will display a blinking “ ” on the scale.  
If the MID.TONE button is not pressed,the measured value will be set automatically in  
the middle of the EV scale.(See the section “3-2-3”)  
Reference:  
• In custom setting (see page 40), it is possible to select which value (last measurement,  
first memorized value or last memorized value) will become the middle value on the EV  
scale if the MID.TONE button is not pressed.  
-48-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Camera Exposure Profiling  
2) The EV scale displays Clipping points(+/-),Dy-  
namic range(+/-)and Mid. Tone with a triangle  
"icon.  
"
Clipping point(-)  
Dynamic range(-)  
Clipping point(+)  
Dynamic range(+)  
3) Measured value exceeding Dynamic range will  
be displayed as a slow blinking "  
icons.Measurements that exceed the clipping  
"
Mid.Tone  
points will be displayed as fast blinking "  
"
icons.  
Exceed dynamic  
Exceed clipping  
range(blinking slowly)  
point (blinking faster)  
Mid. Tone (blinking)  
Reference:  
• In the custom setting mode (see page 40), it is possible to select how to indicate the  
clipping points and the dynamic range. Below are the three display choices.  
Five point  
Inside Range  
Outside Range  
3-2-3 MID.TONE button  
This button is used to set the measured value in the center of EV scale.  
1) Take a measurement by pressing the Measur-  
ing button . Press MID.TONE button to  
set the Mid.Tone on the scale. ”  
” in the  
center of the EV scale will blink continuously  
twice to indicate that the Mid.Tone has been  
set.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-49-  
7. Camera Exposure Profiling  
2) After setting the Mid.Tone (ex.Incident reading), take measurements (highlight or shadow,  
etc. with spot reading) and memorize them to see if measurements are within Dynamic  
range or Clipping points.  
Mid. Tone  
F5.65  
Measure and memorize  
the Highlight  
F160  
Measure and memorize  
the Shadow  
F2.03  
3) Adjusting Mid.Tone Value  
If it becomes necessary to change the measured mid-tone value, press and hold down  
the MODE button while pressing the MID.TONE button (M 0 will start to blink) this will  
lock the mid-tone value on the scale. After the mid-tone is locked press and hold down  
the MID.TONE button and rotating the Jog wheel until the mid-tone value is positioned  
where it is desired.  
NOTE:  
If you do not lock the mid-tone value (MODE than MID.TONE = "M 0" blinking) the mid-  
tone scale will shifts to the last measured value when you press the MID.TONE button.  
Mid-tone recall mode  
Mid-Tone adjustment  
with Jog Wheel  
-50-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Camera Exposure Profiling  
4) Setting Mid.Tone Value from Memorized Values  
After taking three or more reflected Spot measurements, select which memorized value  
on the analog scale should be the Mid-Tone value. First enter the memory recall mode  
by pressing and holding the MODE button, while pressing the Memory button. Select  
one of the memorized values by rotating the Jog wheel and press the MID.TONE button  
to set it as the Mid-tone value.  
Memory button  
Memory recall mode  
Select desired memorized  
value as Mid.Tone  
Press MID.TONE to set  
NOTE:  
Depending on the lighting conditions, type of photographic equipment and the exposure  
standard adopted your exposure result may differ. Please test your setup before shooting  
under any conditions.  
It is possible that your set exposure values are not the desired effect for the given  
subject matter or shooting situation. Under these situations, please compensate the  
values to achieve the desired effect. See section 2-2 "Manual Exposure Profile Input"  
(See page 45)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-51-  
8. Optional Accessories  
Synchro cord  
This is a five-meter long cord with three plugs. An exposure  
meter, a camera, and a flash can all be connected at the  
same time. This is convenient when measurements are  
made, because it is not necessary to plug and unplug the  
synchro cord.  
18% Gray Card  
18% gray card with cover (110mm x 102mm, 4 1/4” x 3 1/  
2”), folds to 2 3/4” x 4 3/4”, and fits in a shirt pocket.  
It provides accurate exposures regardless of reflected ratio  
of the subject and surroundings.  
Lens Hood/Step-Up Ring (30.5mm 40.5mm)  
The step-up ring, available as an optional accessory, makes  
it possible to mount step rings and filters of other  
manufacturers. This simplifies the setting of exposure without  
the troublesome correction calculation of PL filters, etc.  
The step-up ring can also be used as a Lens hood to protect  
the spot lens from scratching, soiling, and avoids lens glare  
which could cause incorrect light measurements etc.  
Exposure Profile Target  
This is a Gray Scale Test target for Exposure Profiling and  
meter calibration. (The size is 260 x 160mm. 10.2” x 6.3”).  
One side is nine gray patches including black and white, and  
the other side is an: 18% gray card for digital camera white  
balancing and spot metering.  
-52-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Optional Accessories  
Wireless Flash Radio Triggering module  
(For the L-758D or L-758CINE. )  
Electronic flash units and/or cameras can de triggered wireless from the L-758 or L-758CINE with  
optional radio module using PocktWizard Receiver or Trans ceivers connected to them.  
Radio transmitter module (32 channels)  
RT-32FCC  
RT-32CE  
(for US or Canada)  
(for EU countries)  
Radio frequency  
FCC & IC (indicating “Use RT-32FCC for radio transmitter module” on the back of body)  
CH1 ~ 16 : 344.0MHz CH17 ~ 32 : 346.5 ~ 354.0MHz  
CE (indicating “CE” on the back of body)  
CH1 ~ 16 : 433.62MHz CH17 ~ 32 : 434.22MHz  
Reference:  
RT-32FCC/CE transmitter module, old Sekonic RR-4 and RR-32 receivers are compatible with  
PocketWizard® products from LPA Design (www.pocketwizard.com), Profoto® products  
NOTE:  
Before purchasing PocketWizard wireless (radio frequency) your light meter’s is compatible  
equipment, be sure that it is correct radio frequency for the country that will be used in and  
is the same radio frequency as the light meter.  
PocketWizard and Sekonic’s Radio Triggering system may be used only in countries where  
a permit for the approved frequency has been issued by the government office in charge.  
There are several kinds of approved frequencies in the world, and we recommend you to  
be sure that check your Sekonic light meter Transmitter and Receiver(s) or Transceiver  
(s) are compatible with each other.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-53-  
9. Technical Data  
· Type  
:
:
Digital exposure meter equipped with 1° spot viewfinder for ambient  
and flash light  
· Light receiving method  
Incident light and reflected light  
· Light Receptors  
Incident light  
:
:
Convertible to flat diffuser (with retracted Lumisphere)  
1° spot with display in finder  
Metering distance 1m ~ ∞  
Reflected light  
· Light receptor element  
:
:
2-Silicon photo diodes (incident and reflected)  
· Metering modes  
Ambient light  
Aperture priority metering  
Shutter priority metering  
EV metering  
Simple illumination measurement (lux, foot-candle)(758CINE only)  
Simple brightness measurement (foot-lambert, cd/m2)(758CINE only)  
With synchro cord (cumulative, non-cumulative)  
Without synchro cord (cumulative, non-cumulative)  
Measurement using the wireless flash radio triggering sysytem (cu-  
mulative, non-cumulative) (optional for L-758D/758CINE)  
Flash  
:
· Measuring Range (ISO 100)  
Ambient light  
Incident light  
Reflected light  
Flash  
:
:
EV-2 to EV 22.9  
EV 1 to EV 24.4 (with 1° spot viewfinder)  
Incident light  
Reflected light  
:
:
f0.5 to f161.2 (approx. f175)  
f2.0 to f161.2 (approx. f175) (with 1° spot viewfinder)  
Illumination (direct measurement is possible only in 758CINE)  
:
0.63 - 190,000 lux (2 significant digits)  
0.10 - 180,000 foot-candle (2 significant digits)  
Brightness (direct measurement is possible only in 758CINE)  
:
0.25 - 190,000 cd/m2 (2 significant digits)  
0.10 - 190,000 foot-lambert (2 significant digits)  
· Repeat Accuracy  
:
+/- 0.1 EV or less  
· Calibration Constant  
Incident light metering  
Reflected light metering  
:
:
Lumisphere C = 340 Flat diffuser C = 250  
K = 12.5  
· Display Range  
Film speed  
:
:
ISO 3 to 8000 (in 1/3 steps)  
Shutter Speeds  
Ambient light  
30 minutes to 1/8000 seconds(in 1, 1/2 or 1/3 steps)also 1/200, 1/400  
Cine speeds- 2, 3, 4, 6, 8, 12, 16, 18, 24, 25, 30, 32, 36, 40, 48, 50,  
60, 64, 72, 96, 120, 128, 150, 200, 240, 256, 300, 360 frames per  
second (at a 180 degree shutter angle)  
Additional Cine speeds to 758CINE  
1, 10, 14, 20, 75, 90, 100, 125, 180, 250, 375, 500, 625, 750, 1000 (at  
a 180 degree shutter angle)  
Flash  
:
30 minutes to 1/1000 second (in 1, 1/2 or 1/3 steps),also 1/75, 1/80,  
1/90, 1/100, 1/200, 1/400  
-54-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Technical Data  
Aperture  
EV  
Analog scale  
:
:
:
f/0.5 to f/161.2 (in 1, 1/2 or 1/3 steps)  
EV -9.9 to EV 46.6 (in 1/10 steps)  
F-scale  
F0.7 – F90 (in 1/3 steps), (for 758DR/758D)  
F0.5 – F64 (in 1/3 steps), (for 758CINE)  
EV scale -7.0EV to +7.0EV (in 1/3 steps)  
: +/- 9.9 EV (in 1/10 steps)  
Contrast function  
Shutter angle (758CINE only)  
:
1° ~ 10° (in 1°steps),15° ~ 270° (in 5°steps), plus12°,17°, 22°,144°,172°  
+/- 5.0 EV (in 1/10 steps)  
Filter compensation  
:
Filter factor number compensation (758CINE only)  
:
:
85-, n3-, n6-, n9-, A3-, A6-, A9-  
Multiple Flash function  
Up to flash cumulated readings  
(only one digit is displayed when the cumulated number is ten or more.)  
+/- 9.9 EV (in 1/10 steps)  
+/- 1.0 EV (in 1/10 steps)  
0 to 100% in 10% increments  
Exposure compensation  
Calibration compensation  
Flash analyzing function  
:
:
:
· Other features  
:
:
:
All-weather feature  
Memory function  
JIS standard water resistance class 4, splash-proof type  
9 readings  
Memory clear • recall function  
Average function  
:
up to 9 readings can be averaged.  
Out of display or measurement range  
:
Eu (underexposure) or Eo (overexposure) indication  
Battery Power Indicator display  
:
with 3 level status icon  
Auto Power Off  
:
:
:
:
:
Selectable in Custom Setting  
EV 6 and under  
14 items (for L-758DR/758D), 17 items (for L-758CINE)  
-2.5 to 1.0D  
Auto illumination  
Custom setting function  
Diopter adjustment  
Tripod socket  
1/4” and 20 threads  
(for placing meter in subject area for cordless flash measuring).  
Second ISO film speed setting: ISO 3 to 8000 (in 1/3 steps)  
· Battery used  
:
one of CR123A battery 3V, (lithium dry cell)  
· Operating temperature range : -10 ~ 50°C  
· Storage temperature range  
· Dimensions  
:
:
:
:
-20 ~ 60°C  
90 w x 170 h x 48 d mm  
268 g (with battery)  
· Weight  
·
Standard accessories supplied  
Soft case, strap, lens cap, USB-cable, synchro terminal cap,  
CR-123A lithium battery x 1, quick guide,  
Sticker for Multi-key Operation and CS, software in CD-ROM  
·
Radio triggering range  
:
approx. 30 meters (approx. 100 feet)  
· Radio wave frequency  
FCC & IC  
:
:
CH1 ~ 16  
CH17 ~ 32  
CH1 ~ 16  
CH17 ~ 32  
344.0MHz  
346.5 ~ 354.0MHz  
433.62MHz  
CE  
434.22MHz  
Features and specifications are subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-55-  
10. Care and Maintainance  
NOTE:  
Although this meter has an All-weather design for everyday use (JIS standard water  
resistance class 4), do not place it in water or use it underwater. This will cause it to  
malfunction.  
Splashed  
Do not wash with water  
Do not submerge or use under water  
Rain  
To avoid damaging this meter, never drop it or subject it to shock.  
Avoid storing it in places with high temperatures or humidity.  
Avoid excessive temperature changes which could cause internal condensation,  
resulting in malfunction.  
If the temperature of the meter drops to -10 deg. C or beyond, response of the LCD  
becomes extremely slow and displays are difficult to read. At temperatures between 0  
and 10 deg. C the LCD will become somewhat slower than normal but this does not  
hinder usage. Also, when the temperature exceeds 50 deg. C, the LCD will turn black  
and will be hard to read. This will return to normal when the temperature returns to  
normal.  
Do not place the meter in direct sunlight during midsummer or near heaters, etc., as  
the temperature of the meter will rise beyond that of the air temperature. Be careful  
when using the meter in hot locations.  
Maintenance Notes  
If your meter is splashed with water, wipe immediately with a soft dry cloth. This will  
cause rust or corrosion.  
Avoid applying excessive force on the rubber seal of the battery compartment cover or  
attempting to remove it. This will cause inundation, corrosion or malfunction.  
If the rubber seal’s surface is damaged,water or moisture may enter and damage the  
meter. If this has happened, you must send your meter to the Sekonic Sevice Center in  
your country.  
When light meter get dirty, clean it with soft dry cloth. Never use organic cleaners (like  
thinner or benzene).  
-56-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC & IC compliance information  
Warning: Changes or modifications to this unit not expressly approved by the party responsible for  
compliance could void the user's authority to operate the equipment.  
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant  
To Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instruction, may cause harmful interference  
to radio communication.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment  
does cause harmful interference to radio or television reception, which can be determine by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
* Reorient or relocate the receiving antenna.  
* Increase the separation between the equipment and receiver.  
* Consult the dealer or an experienced radio/TV technician for help.  
This device complies with Part 15 of the FCC rules and also with RSS-210 of Industry & Science Canada.  
Operation is subject to the following two condition: (1) This device may not cause harmful interference,  
and (2) this device must accept any interference received, including interference that may cause undesired  
operation.  
FCC ID  
Number  
IC  
Number  
Model  
Note  
The approval of this rule is obtained under the  
L-758DR  
PFK-758-01  
3916A-758001 condition that radio transmitter module is installed  
in the meter.  
The approval of this rule is obtained with optional  
radio transmitter module (RT-32FCC). In installing  
radio transmitter module into the meter, be sure to  
L-758CINE PFK-RT32-01 3916A-RT3201 put the sticker indicating FCC ID and IC number on  
the back of meter which is enclosed in the package  
of the module. For details, please refer to the  
instruction manual of transmitter module.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-57-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blank page  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-24-14, OIZUMI-GAKUEN-CHO, NERIMA-KU, TOKYO 178-8686 JAPAN  
( )  
( )  
TEL:+81 0 3-3978-2335 FAX:+81 0 3-3978-5229  
JH1297562  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q See DVR QSD2216 User Guide
RCA Camcorder CC634 User Guide
RCA Camcorder CC638 639 User Guide
Rotel Turntable RP 1010 User Guide
Samson Stereo Amplifier MXS3000 User Guide
Samsung CRT Television WS 32Z308T User Guide
Samsung Flat Panel Television HP R4252C User Guide
Sanyo Flat Panel Television 32LM5R User Guide
Schumacher Battery Charger PS 1022M User Guide
Senco Staple Gun WC150RXP User Guide