Owner’s Instructions
SW80ASP/SW95ASP
CONTENTS
Page
FEATURES ............................................................................................1
DESCRIPTION OF PARTS....................................................................2
SAFETY INSTRUCTIONS .....................................................................3
INSTALLATION & MAINTENANCE......................................................4
ENVIRONMENT................................................................................4
IN CASE OF PUMP-DRAINED WASHER .......................................4
HOW TO CONNECT WATER SUPPLY HOSE ................................4
CLEANING THE FILTER NET..........................................................5
HOW TO ADD THE DETERGENT ...................................................5
HOW TO ADD THE FABRIC SOFTENER.......................................5
CLEANING THE FILTER ..................................................................5
LEVELLING.......................................................................................5
PRECAUTIONS ................................................................................6
WASHING INSTRUCTION.....................................................................6
PROCEDURE ...................................................................................6
WASH PROGRAM............................................................................7
WASHING PROGRAM DETAILS..........................................................7
OPTIONAL CYCLE................................................................................8
TROUBLESHOOTING...........................................................................8
SPECIFICATION
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF PARTS
WATER SUPPLY HOSE
RED-HOT WATER
LID
WATER SUPPLY HOSE
WHITE-COLD WATER
DRAIN-HOSE
DETERGENT BOX
CONTROL PANEL
POWER PLUG
FABRIC SOFTENER
DISPENSER
BLEACH INLET
MAGIC FILTER
Lint will be collected in
the filter during washing.
HEIGHT ADJUSTING
FEET
CONTROL PANEL
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
WARNING!
To reduce the risk of fire, electric shock, or injury to persons when using your appliance,
take care to adhere to the following precautions.
● Maximum hot water supply temperature
● Where an unearthed power cord is not fitted,
60 degrees.
be sure that the washer is grounded.
To avoid electrical shock use metal piping for the ground
connection.
●● Before washing, check all pockets.
Take care not to ground the washer to
If nails or pins remain in pockets, they may damage the
gas pipes or telephone cables due to the
washer or clothes.
danger of explosion from lightning strikes.
● Don’t press the control panel with a sharp
● During spinning, don't put your
hand in the spin basket.
Because the spin basket is rotating at the
object.
Panel damaged or malfunction may occur.
high speed, rotating parts may injure your
hand.
If the control panel for this washer is damaged,
it must be replaced by a repair shop appointed by the
manufacturer, as special purpose tools are required.
●● Do not operate this appliance if it is damaged,
malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged
cord or plug.
● Openings must not be obstructed by carpeting
when the washing machine is installed on a
carpeted floor.
● Turn off water taps when the washer is not in
use to avoid water pressure damage to the
pump.
● Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
● To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
● The instructions for use shall specify the
maximum mass or dry cloth in kg, for which the
appliance is designed.
attempting any maintenance or cleaning.
● If the appliance is supplied from a cord
extension set or electrical portable outlet
device the cord extension set or electrical
portable outlet device should be positioned so
it is not subject to splashing or ingress of
moisture.
● The appliance is not intended for use by young
children or infirm persons without supervision.
● Young children should be supervised to ensure
that they do not play with the appliance.
● This appliance is not intended for use by young
children or infirm persons unless they have
been adequately supervised by a responsible
person to ensure that they can use the
appliance safely.
Young children should be supervised to ensure
that they do not play with the appliance.
● If the power supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person in order to
avoid a hazard.
● Place clothes evenly into the washer as
unevenly distributed laundry may cause
excessive out-of-balance noise and vibration.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION & MAINTENANCE
IN CASE OF PUMP-DRAINED WASHER
ENVIRONMENT
•
Be sure to join tightly the
drain hose into the drain-
outlet on the back of the
machine.
•
Install the drain hose in
the position of about
70~80 cm above the
ground.
Leave some space
Maintain at least 10cm between the washer and
the wall.
Place the washer on a sturdy flat
surface.
If the washer is placed on an uneven or weak
surface, noise or vibration occurs. (Allowable
slope is 1 degree)
Never install the washer in a very
steamy environment or where it might
be open to the rain.
Excessive moisture may cause an electrical
shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected
by direct heat,never place the washer near
furnaces, boilers,etc. Do not place under direct
sunlight.
HOW TO CONNECT WATER SUPPLY HOSE
Check the type of tap fitting which is in your laundry and then see appropriate instruction below:
A tap of ordinary type is desirable
In case of square tap
●
Take out the internal part of the connector
and join it in the following way.
Internal part
ORDINARY TAP
SQUARE TAP
ROTATING TAP
4. Connect the water supply hose
1. Remove the adaptor from the
water supply hose.
to the adaptor. Pull down the
part (c) of the water supply
hose. When you release part (c)
the hose is automatically
connects to the adaptor making
a 'click' sound.
c
2. First,using a "+" type screw
driver, loosen the four screws
on the adaptor. Next,take the
adaptor and turn part(b)
following the arrow for gap
about 5mm between them.
5. Connect the other end of the
water supply hose to the inlet
water valve at the top of the
washer.
Screw the hose clockwise all
the way in.
a
b
6. If the water tap is a screw
type,assemble a water supply
hose that fits to the tap as
shown.
3. Connect adaptor to the water
tap by tightening the screws
firmly.
Then,turn part (b) following the
arrow and put (a) and (b)
together.
c
Note : The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not
be used.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING THE FILTER NET
1.Push the upper part of
the filter and pull in.
2.Open the cover as
shown in the figure.
3.Clean the filter.
4. Close the cover and insert the lower
part of the filter in the basket first and
then push the filter with "click" sound .
HOW TO ADD THE DETERGENT
LEVELLING
Adjustment the heigt of the machine
Adjust the legs to level the washer
Be careful not to put in your hand under the legs.
1. Open the detergent box by pulling in
the direction of the arrow as shown in
the figure.
2. Add the amount of detergent for one
washing evenly in the box so that the
detergent does not overflow the box.
Pull the handles located at the
right and left of the front side and
slide off.
Adjust the height of the machine
upward or downward.
HOW TO ADD THE FABRIC SOFTENER
●
When a proper amount of fabric softener is stored in the
box, it is automatically added in at the final rinse cycle.
In case the hot water only is connected, this function will
not be operated.
When the adjustment is finished,
push the handles to fix the
adjusting legs.
●
SEE IF THE MACHINE IS PLACED LEVEL BY
CHECKING THE POSITION OF THE WASHING TUB.
●
When too much softener is stored above the base line, it
may not be operated properly.
●
Open the lid of the machine, pour water into the tub up to
the level just below the pulsator, and adjust the legs so
that the pulsator is positioned at the center of the water as
shown in the figure.
● Place the machine more than 10cm away from the wall.
Water
CLEANING THE FILTER
(pump drained washer)
1. Place a rag under washer filter not to wet the floor.
2. Turn the filter-cap to the left.
3. Take out the filter and remove any sludge.
4. Reassemble in reverse order.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING! NOTE THE FOLLOWING PRECAUTIONS TO PREVENT ELECTRICITY
LEAKAGE AND THE POSSIBILITY OF ELECTRIC SHOCK.
Earthing is necessary to prevent leakage or electric shocks caused by the electric currents leaked from the machine.
How to earth an outlet with earthing terminals when
an earthed power load is not fitted.
Outlet with earthing terminals:
● Even when the internal wires of the earthing terminals are joined,
connect the earthing conductor (green) of the machine to the tap.
When using an extension cord and a boosting transformer:
● Make sure that the earthing conductor is connected.
Never make an earthing to
● The telephone line, lightning rod, or gas pipe as it is
extremely dangerous in case of lightning strikes.
TO DO A CLEAN WASHING
•
•
•
•
•
Press the POWER botton.
Pour a little detergent into case-detergent.
Turn on water supply to the wshing machine.
Choose the SOAK in CYCLE button and the HIGH in WATER LEVEL button.
Press the START/PAUSE button.
WASHING INSTRUCTION
PROCEDURE
1
. Sort the laundry into separate wash loads.
Each load of washing should contain clothing which needs the same washing conditions.
For example, you should not wash delicate clothes with very dirty work clothes.
2
. Load the laundry into washing.
Before load, check all pockets, and close zippers, hooks and eyes.
3. Add the detergent. (see page 5)
4. Add the fabric softener. (see page 5)
5. Close the lid.
6. Press power button.
7. Choose the wash program & optional cycle. (see page 7~8)
If you choose “SENSOR” program you don’t need to select water level.
Water level is set automatically at “SENSOR” program.
Press the START/PAUSE button.
8. Select the water level.
Before choosing the water level, remember following things.
When you choose SENSOR, HEAVY-DUTY, ECONO-WASH, DELICATE program,
water level is selected “AUTO” automatically, but if you wat to choose water level manually
you can select. HIGH, MEDIUM, LOW, EXTRA LOW
6
Download from Www.Somanuals.com. All Manuals Search And Download.
9
. Select the water temperature.
Before choosing the water temperature remember the following:
1) You can choose HOT, WARM, COLD on all programs except for delicate program.
HOT is hot wash and cold rinse.
WARM is warm wash and cold rinse.
COLD is cold wash and cold rinse.
2) When you choose delicate program, water temperature is selected automatically for warm wash and warm rinse.
10. Close the lid and press the START/PAUSE button.
11. Do you wat extra rinse?
For extra rinses press the cycle key 1 to 5 times (depending on the number of extra rinse required).
You can select up to 5 extra rinses or return to a single rinse by pressing the cycle key.
The time left display will show the number of rinses selected.
Note tat the extra rinse program is not available when pause is selected or during the spin cycle.
WASH PROGRAM
WOOL
6 min
ECONO WASH
5 min
DELICATE
6 min
SENSOR
18 min
HEAVY DUTY
20 min
Wash Time (SW80ASP)
Wash Time (SW95ASP)
Wash Action
6 min
5 min
6 min
25 min
26 min
Gentle
Normal
Gentle
Normal
Normal
HOT
WARM
COLD
HOT
WARM
COLD
HOT
WARM
COLD
Wash Temp.
WARM
COLD
WARM
COLD
WARM
COLD
WARM
COLD
COLD
COLD
COLD
Deep Rinse
Spin Time
1 min
3 min
1 min
6 min
6 min
36 min
36 min
40 min
40 min
37 min
37 min
Total Time
SW80ASP
(High Water level) SW95ASP
56 min
62 min
59 min
63 min
WASHING PROGRAM
SENSOR Program
HEAVY DUTY Program
●
●
The best washing program is chosen automatically
Load size and water level is determined automatically
●
●
This program is suitable for heavily soiled laundry
Load size and water level is determined automatically
or you can choose the water level you want
●
Unplug the power cord after washing.
●
Unplug the power cord after washing.
ECONO WASH Program
WOOL Program
●
●
●
Saving your time and energy
●
●
This program is suitable for woollen clothes
This program is suitable for heavily soiled laundry
Load size and water level is determined automatically
or you can choose the water level you want
Only high and medium water levels are available
●
Unplug the power cord after washing.
●
Unplug the power cord after washing.
DELICATE Program
●
Washing action is very gentle, so this program is
suitable for delicate clothes like lingerie.
●
Load size and water level is determined automatically
or you can choose the water level you want
●
Unplug the power cord after washing.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL CYCLE
WASH ONLY
RINSE ONLY
●
●
When you choose this cycle, wash cycle is operated.
Pressing optional cycle key during washing changes
the wash time in two minute intervals.
The wash time can be changed to between 3 and 25
minutes.
●
When you choose this function, only rinse cycle is
operated.
●
Pressing function key during rinsing changes the
number of rinse. Up to 5 rinses can be optionally
selected.
●
●
Load size and water level is determined automatically
●
● Unplug the power cord after washing.
Unplug the power cord after washing.
SOAK
DRIP DRY
●
●
●
The laundry is soaked in water so that heavy dirt can be
●
The function allows you to take drip clothes out of the
washing machine while they are still wet before the final
spin.
eliminated sufficiently.
You can choose soak cycle after choosing wash
program.
When you select soak function, 5 minute cycle (1 min.
washing then 4 min. pause) continue for 30 minutes
before main wash program.
●
●
You can choose drip dry cycle after choosing main
wash program.
When you select drip dry the cycle in finished before
final spin.
●
Load size and water level is determined automatically
● Unplug the power cord after washing.
●
Unplug the power cord after washing.
SPIN ONLY
RINSE AND SPIN ONLY
●
●
You can choose this cycle, only cycle is operated.
Pressing cycle key during spinning only cycle changes
the spin dry time.
●
When you choose this cycle, only rinse & spin cycle are
operated without wash cycle.
●
Pressing cycle key during operation changes the
number of rinse (see above).
The spin dry time can be changed to between 1 and 7
minutes.
You cannot change the spin dry time using this function.
●
Unplug the power cord after washing.
● Unplug the power cord after washing.
DELAY START
●
●
This function allows you to delay the start of your chosen wash program for 3, 4, ... 18 hours.
By pressing the delay start key you can select delayed period for 3, 4, ... 17, 18 hours, and your washing machine will
finish the selected wash program after the delayed period.
TROUBLESHOOTING
Washing machine won’t work
Spinning does not work
Is the water tap opened?
Is the washer plugged in?
Is the power cut off?
Is the laundry spread out evenly
in the washer?
Is the washer set on a sturdy
flat surface?
Is the fuse all right?
Is there enough water?
Is the lid closed?
Water does not drain
Water is not supplied
Is the drain hose down? (No pump)
Is the drain hose frozen?
Is the water tap opened?
Is the water cut off?
Is the drain hose clogged?
Is the water supply hose or
If the water does not drain in 15
minutes, a buzzer will sound, and the
remaining time indicator will show “E”
hose connection clogged?
Is the water tap frozen?
If water is not supplied in 60 minutes,
a buzzer will sound, and the remaining
time indicator will shown “7E”.
While lid is opening,
Water supply does not stop
the washing machine won’t work
Make sure to close the lid while washing machine is
operating.
Close the water tap.
Disconnect the power supply card.
Call to service center or agency.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
IF YOU NEED HELP WITH YOUR NEW
SAMSUNG WASHING MACHINE
Contact your nearest Samsung office or Samsung authorized
service center for technical assistance
SPECIFICATION
SW80ASP
550
SW95ASP
Power input(Watts)
Load capacity(kg)
550
8.0
9.5
Size(WxDxH)(mm)
640 X 698 X 1050
50
640 X 698 X 1070
50
Net Weight(kg)
Water Consumption(liters)
Water Pressure(min-max)
190(high)
50~780KPa
189(high)
50~780KPa
CODE NO. : DC68-01277A-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|