Samsung Security Camera SNB 3000P User Guide

SNB-3000(P)

Network Camera

User Manual

imagine the possibilities

Thanks you for purchasing this Samsung product.

To receive a more complete service, please visit

our website

www.samsungsecurity.com

RoHS compliant

Our product complies with “The Restriction Of the use of certain Hazardous

Substances in electrical and electronic equipment”, and we do not use the

6 hazardous materials- Cadmium (Cd), Lead (Pb), Mercury (Hg), Hexavalent

Chromium (Cr ), Poly Brominated Biphenyls (PBBs), Poly Brominated Diphenyl

Ethers (PBDEs)- in our products.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. When installing the camera, fasten it securely and ﬁrmly. The fall of

camera may cause personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts,

etc.) or containers ﬁlled with water on top of the camera. Doing so may

cause personal injury due to ﬁre, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations. Doing so may

cause ﬁre or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the

product. In such case, immediately disconnect the power source and

contact the service center. Continued use in such a condition may cause

ﬁre or electric shock.

9. If this product fails to operate normally, contact the nearest service

center. Never disassemble or modify this product in any way. (SAMSUNG

is not liable for problems caused by unauthorized modiﬁcations or

attempted repair.)

10.When cleaning, do not spray water directly onto parts of the product.

Doing so may cause ﬁre or electric shock

11.Do not expose the product to the direct airﬂow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome

due to temperature difference between internal and external of the dome

camera.

12.If you install this product in a low-temp area such as inside a cold store,

you must seal up the wiring pipe with silicon, so that the external air can

not ﬂow inside the housing.

Otherwise, external high, humid air may ﬂow inside the housing, pooling

moisture or vapor inside the product due to a difference between internal

and external temperature.

English _ꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

overview

CAUTIoN

1. Do not drop objects on the product or apply strong blows to it. Keep

away from a location subject to excessive vibration or magnetic

interference.

2. Do not install in a location subject to high temperature (over 50°C), low

temperature (below -10°C), or high humidity. Doing so may cause ﬁre or

electric shock.

3. If you want to relocate the already installed product, be sure to turn off

the power and then move or reinstall it.

4. Remove the power plug from the outlet when there is a lighting storm.

Neglecting to do so may cause ﬁre or damage to the product.

5. Keep out of direct sunlight and heat radiation sources. It may cause ﬁre.

6. Install it in a place with good ventilation.

7. Avoid aiming the camera directly towards extremely bright objects such

as sun, as this may damage the CCD image sensor.

8. Apparatus shall not be exposed to dripping or splashing and no objects

ﬁlled with liquids, such as vases, shall be placed on the apparatus.

9. The Mains plug is used as a disconnect device and shall stay readily

operable at any time.

10.When using the camera outdoors, moisture may occur inside the camera

due to temperature difference between indoors and outdoors. For this

reason, it is recommended to install the camera indoors. For outdoor

use, use the camera with built-in fan and heater.

ꢂ_ overview

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC STATemeNT

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received including interference that

may cause undesired operation.

CAUTIoN

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct

the interference at his own expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the

Canadian Interference.-Causing Equipment Regulations of

ICES-003.

English _ꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

overview

ImpoRTANT SAFeTy INSTRUCTIoNS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, or other apparatus

(including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong is

provided for your safety. If the provided plug does not ﬁt into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the

apparatus has been damaged in any way, such as powersupply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on the apparatus

ꢄ_ overview

Download from Www.Somanuals.com. All Manuals Search And Download.

CoNTeNTS

Important Safety Instructions

Product Features

overview

Precautions – Installation And

Use

Recommended Pc Speciﬁcations

What’s Included

At a Glance

Mounting the lens

installation &

Inserting/Removing an SD

Memory card

connection

Memory card Information

(not included)

connecting with other Device

How to use the menu key

Main Menu

^camera2^set2^up

Proﬁle

camera Setup

Privacy Zone

Others

System Info

Language

connecting the camera to an

IP Router with the xDSL/cable

Modem

network connection

^and3^set1^up

connecting the camera to

an IP Router with Local Area

Networking

connecting the camera Directly

to a DHcP-Based xDSL/cable

Modem

connecting the camera Directly

to Local Area Networking

IP Address Setup

Static IP Setup

Dynamic IP Setup

Port Range Forward (Port

Mapping) Setup

connecting to the camera From

a Shared Local Pc

connecting to the camera From

a Remote Pc via the Internet

English _ꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

overview

connecting to the camera

web viewer

Installing Activex

Using the Live Screen

Backup

Using the SD Search Viewer

Screen

Accessing the Setup screen

Default Setup

setup screen

System Setup

Overlay Setup

Event Setup

Network Setup

Proﬁle

appendix

Terminology

Speciﬁcations

Frame Rate (NTSc)

Frame Rate (PAL)

Troubleshooting

ꢆ_ overview

Download from Www.Somanuals.com. All Manuals Search And Download.

pRodUCT FeATUReS



Support various communication protocols

Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various

internet protocols such as ARP, HTTP, HTTPS and DHCP.



Web Browser-based monitoring

Using the Internet web browser to display the image in a local network environment.



Automatic Local Ip Setup

Even a network novice can install it with minimum operations.



Alarm

If an alarm sensor is connected and it detects a motion, a message is sent to the

registered address via FTP/email (SMTP) or stored in the SD memory card, or an alarm

will signal to the alarm out terminal.



Intelligent video Analysis (the event rule and the motion rectangle box are displayed

only in the mJpeG Live screen.)

If an event rule is deﬁned for the video analysis and it detects a motion in the conﬁgured rule

area, a message is sent to the registered address via FTP/email (SMTP) or stored in the SD

memory card, or an alarm will signal to the alarm out terminal.

pReCAUTIoNS – INSTALLATIoN ANd USe



Do not bend or drop the SD memory card.



Do not store or use the SD memory card in a high temperature, high humidity or dusty

place.



Be careful not to apply foreign substances on the terminals of SD memory card.



In case of cleaning terminals, wipe gently with a soft cloth.



Before ejecting the SD memory card, release the checkbox <Sd Card Record> in

<Alarm image> and press [Apply] button. (page 61)



If SD memory card have reached its lifespan, no data will be saved.

In this case, purchase a new one and replace the SD memory card.

ReCommeNded pC SpeCIFICATIoNS



CPU : Pentium4 / 2.4GHz or higher



Operating System : Windows XP(Service Pack2, Service Pack3) / Windows Vista / Windows 7



Resolution : 1024X768 pixels or higher



RAM : 512MB or higher



Web Browser : Internet Explorer 6.0 or higher



Video Card : Radeon, Nvidia



Video Memory: 128MB



DirectX 8.1 or higher

English _ꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

overview

Compatible Ip Routers



Linksys



D-Link



Netgear

Compatible poe Switches



Linksys SRW224G4P



D-Link DES-1316



SMC SMCPWR-INJ3

WhAT’S INCLUded

Please check if your camera and accessories are all included in the product package.

C Mount Adapter

Camera Holder (Mount)

& Screws (2EA)

Camera

Auto Iris Lens Connector

User Manual/

User Manual

IP INSTALLER DVD

Lens options

CS Lens

C Lens

10_ overview

Download from Www.Somanuals.com. All Manuals Search And Download.

AT A GLANCe

Front Side

Item

Description

Camera Holder

Used when you mount the camera onto the bracket by fixing the camera

holder (mount) adaptor with the bracket.

(Mount) Holes

Auto Iris Lens

Installed on the lens adaptor.

(Optional)

Auto Iris Lens

Connector

Used to supply power and output signal to control the iris of the lens.



Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied

ethanol.

English _11

Download from Www.Somanuals.com. All Manuals Search And Download.

overview

Rear Side

AUDIO OUT AUDIO IN

SD CARD

SD SYSTEM POWER

RESET

VIDEO

NETWORK

1,2 : ALARM IN 1,2

: GND

4,5 : ALARM OUT 1,2

ACT

LINK

GND

AC 24V

DC 12V

Item

Description

SD Memory Card

Compartment for the SD memory card.

Compartment

AUDIO OUT Terminal for audio output.

Audio Out terminal

AUDIO IN

Terminal for audio input.

ON: A memory card is inserted and operates normally.

Flashing: Failed to record, insufficient space, or inserted

abnormally.

OFF: Camera is off, camera is restarting, or memory card

not in place.

System, Power

Indicators

ON: The camera is turned on and connected to the network

properly.

SYSTEM

POWER

Blinking: During DDNS setup, or in case of setup failure, or

in a state of unstable network connection

OFF: When the system is rebooting, or turned off

ON: While the power is on

OFF: If the power is off

1ꢀ_ overview

Download from Www.Somanuals.com. All Manuals Search And Download.

Resets the camera settings to the default. Press and hold it for about 3

seconds to turn off the system indicator and restart the system.

Reset Button

Power Port

GND

Used to plug the power cable.

Used for earth-grounding.

Network Port

Used to connect to the Network cable.

ALARM IN

Used to connect the alarm input signal.

1,2

I/O Port

GND

Used for earth-grounding.

ALARM OUT

Used to connect the alarm output signal.

1,2

Video Out Port

Video signal output port connected to the monitor.

English _1ꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

installation & connection

moUNTING The LeNS

Disconnect the power before proceeding.

mounting the CS lens

Turn the optional CS lens clockwise to insert it.

CS Lens

mounting the C lens

Turn the C mount adaptor clockwise to insert it and do the same with the C lens.

C Lens

1ꢂ_ installation & connection

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Auto Iris Lens connector

Insert the lens connector into the corresponding hole of the camera.

Focusing

Turn the lens left or right to control the zoom and focus the lens so that you can view a clear,

sharp object.

INSeRTING/RemovING AN Sd memoRy CARd

Inserting an Sd memory Card

Push the SD memory card in the direction of the arrow shown in the diagram.



Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the

SD memory card.

English _1ꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

installation & connection

Removing an Sd memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to

eject the memory card from the slot.



Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the

slot when released.

Before ejecting the SD memory card, release the checkbox <SD Card Record> in <Alarm

image> and press [Apply] button. (page 61)

memoRy CARd INFoRmATIoN (NoT INCLUded)

What is a memory card?

The memory card is an external data storage device that has been developed to offer an

entirely new way to record and share video, audio, and text data using digital devices.

Selecting a memory card that’s suitable for you

Your camera supports SDHC memory cards.

You may, however, experience compatibility issues depending on the model and make of

the memory card.

Your camera supports SD memory cards.

Note that supported memory card capacity is up to 2GB.

For your camera, we recommend you use a memory card from the following manufacturers:

SDHC/SD Memory Card: Panasonic, Sandisk, Toshiba

Your camera supports 128MB to 16GB (SD Card : 2GB) of memory card capacity.

Playback performance can be affected depending on the speed of memory card, so use

the high-speed memory card.

To ensure proper recording of video data, we recommend you use a memory card that

supports at least read/write speed 10Mbps and Class 6.

1ꢄ_ installation & connection

Download from Www.Somanuals.com. All Manuals Search And Download.

memory Card Use

SD and SDHC memory cards feature a switch that disables writing data on to the media.

Having this switch to the Lock position will prevent accidental deletion of data stored in the

memory card but at the same time will also prevent you from writing data on to the media.

❖ memory Card Components

Contacts

Lock Switch

SDHC

English _1ꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

installation & connection

CoNNeCTING WITh oTheR devICe

Monitor

AUDIO OUT AUDIO IN

SD CARD

SD SYSTEM POWER

VIDEO

RESET

NETWORK

1,2

4,5

ALARM IN 1,2

GND

ALARM OUT 1,2

ACT

LINK

GND

AC 24V

DC 12V

Power

Network

Connecting to the monitor

Connect the [vIdeo] port of the camera to the video input port of the monitor.

Network Connection

Connect the Network cable to the local network or to the Internet.

power Supply

Use the screwdriver to connect each line of the power cable to the corresponding port of

the camera.



Be careful not to reverse the polarity when you connect the power cable.

You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.

1ꢆ_ installation & connection

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to Audio Input/output

Microphone

LINE-OUT

LINE-IN

Speaker

Pre-Amp

Microphone

1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT

port of the ampliﬁer that the microphone is connected to.



direct mic Connection : Set Audio Input Gain high (10). (Refer to page 51)



Line out Connection : Set Audio Input Gain low (1). (Refer to page 51)

2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.

English _1ꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

installation & connection

Audio I/o Block diagram

Network

Microphone

Speaker Pre-Amp

Pre-Amp



Audio Codec

G.711 PCM. μ-law 64kbps 8kHz sampling



Full duplex Audio

Audio in

Used for mono signal line input (Max.2.4 Vpp)



Audio out

Used for mono signal line output (Max.2.4 Vpp)

Line out impedance

600Ω

ꢀ0_ installation & connection

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to the I/o port box

Connect the Alarm I/O signal to the corresponding port of the rear port box.

AUDIO OUT AUDIO IN

SD CARD

1 2 3 4 5

SD SYSTEM POWER

RESET

VIDEO

NETWORK

1,2 : ALARM IN 1,2

: GND

4,5 : ALARM OUT 1,2

ACT

LINK

GND

AC 24V

DC 12V

: GND

4,5 : ALARM OUT 1,2



ALARM IN 1, 2 : Used to connect the alarm input signal.

GND : Used for earth-grounding.

ALARM OUT 1, 2 : Used to connect the alarm output signal.

Alarm I/o Wiring diagram

ALARM IN 1

ALARM IN 2

GND

External Relay

ALARM OUT 1

External Relay

ALARM OUT 2

English _ꢀ1

Download from Www.Somanuals.com. All Manuals Search And Download.

camera setup

You can configure the camera settings using the Web Viewer.



For accessing the Web Viewer, refer to "Network Connection and Setup". (page 31)

hoW To USe The meNU key

Follow the steps below if you run the Web Viewer for setting the menus.

1. Launch the Web Viewer.

2. From the [Camera oSd] menu in the left

pane, click [menu].

The <mAIN meNU> screen appears.

3. Click the Up/Down ($%) buttons to move to a

desired item.

4. Click the four direction ($%_ +) buttons to navigate through the menu items.

5. To change the value of a selected item, click the Left/Right (_ +) buttons.

6. Click [

Your changes will be applied.

: Exits the menu setup screen.

Before exiting the setup screen, select [SAve] to save your settings, or [QUIT] to

cancel them.

: Saves your settings and returns to the previous screen.

: Returns to the main menu.

: Use this icon if you want to save your settings after you specified the mask area and

privacy area, etc.

Once you saved your settings, the changes remain intact even if you select [QUIT] on

exit.

: Use this icon if you want to delete a mask, or privacy area, etc.

Once you deleted your settings, the deletions remain valid even if you select [QUIT] on

exit.

: This arrow appears next to a menu that contains sub items.

For the items with the "*" mark on the right, You can get help from "Terminology". (page 68)



If intelligent video analysis is enabled, camera’s OSD menu operation can be set as an event.

ꢀꢀ_ camera setup

Download from Www.Somanuals.com. All Manuals Search And Download.

mAIN meNU

You can configure the camera settings to your preference.



pRoFILe

** MAIN MENU **

PROFILE

CAMERA SET

PRIVACY ZONE

OTHER SET

SYSTEM INFO

LANGUAGE

You can select a mode that is appropriate to the

camera installation environment.



CAmeRA SeT

Conﬁgure the camera functions and settings.



pRIvACy ZoNe

You can conﬁgure the privacy settings.



oTheR SeT

You can conﬁgure more settings including

FACTORY DEFAULTS.



SySTem INFo

Shows the camera version and type.



LANGUAGe

Select a preferred one from the supported languages.

pRoFILe

You can select one from the pre-determined modes as appropriate to your specific camera installation

environment.

Your selection on each item in PROFILE will affect all other settings of the camera. For the

setting, refer to "pRoFILe". (page 67)

For selecting and saving each menu item, refer to "how to use the menu key". (page 22)



STANdARd

◄

►

PROFILE

Automatically optimizes the camera settings to

the normal environment.

*STANDARD

ITS

BACKLIGHT

DAY/NIGHT

GAMING



ITS

This setting enables you to analyze the trafﬁc

situation and take the trafﬁc information at a glance.

CUSTOM

BACkLIGhT

This setting enables you to view a sharp background

and object even in a severe backlight scene.



dAy/NIGhT

Automatically optimizes the camera settings to the day and night scene.

GAmING

This automatically conﬁgures the settings so that you can work in a stable illumination

condition as indoors.



CUSTom

Your change to any of the PROFILE settings will switch the display to CUSTOM.

English _ꢀꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

camera setup

CAmeRA SeTUp

You can configure the general settings of the camera module.

^{For se}C^lecA^tinm^{g a}e^ndR^sA^avinId^{g each menu item, refer to "how to use the menu key". (page 22)}

Provide the ID and position for a camera that displays on the screen.

1. Select <CAmeRA SeT> - <CAmeRA Id>.

CAMERA ID

2. Use the four direction ($%_ +) buttons to

select a desired character.

ABCDEFGHIJKLMNOPQRSTUVWXYZO

123456789 : ? +*()/

In the lower input box of the screen, the

selected character will be entered.



You can enter up to 54 characters including alphabets,

numbers and special characters.

SP►► ◄◄SP

LOCATION

- - - - - - - - - - - - - - - - - - - - - - - - -

3. When done, continue to select <LoCATIoN>

to specify the display position of the camera ID.

IRIS

You can set the iris to control the intensity of radiation incoming to the camera.

1. Select <CAmeRA SeT> - <IRIS>.

ALC

2. Use the left/right (_ +) buttons to select either

LENS

LEVEL

BACKLIGHT

---- ----

<ALC> or <eLC>.

[

]



ALC : Controls the luminance automatically.

OFF

LENS : Select a lens to use.

LEVEL : Select the global brightness level.

BACKLIGHT : Select WDR or BLC.

WDR : Deﬁne the composition for weight

factor, the shutter speed in WDR level, and

select outdoor or indoor for white balance

setup.

BLC (Backlight compensation) : Conﬁgure the backlight compensation area by

deﬁning the area size and location.



ELC : Controls the level electronically.

LEVEL : Select an overall brightness level.

BACKLIGHT : Set the area for the backlight compensation.

If you select <USeR> for <AReA>, you can select the area size and location.



If the iris is set to <ALC>, ﬁxing the iris is your priority when you adjust AE and the shutter speed.

ꢀꢂ_ camera setup

Download from Www.Somanuals.com. All Manuals Search And Download.

moTIoN

◄

►

CAMERA SET

You can specify a level of AGC for controlling the

camera motion.

CAMERA ID

IRIS

MOTION

DNR

SHUTTER

SENS-UP

FLICKERLESS

XDR

ALC

(F.FAST)---

MID

Select F.FAST if you want to monitor a very fast

moving object in a low contrast scene, and S.SLOW

if monitoring a very slow moving, inanimate object in

the same condition.

OFF

AUTO X4

OFF

MID

OFF

DIS

As long as DAY/NIGHT is set to AUTO, the

<moTIoN> menu is not available.

dNR

Reduces the noise on the screen.

DAY/NIGHT

WHITE BAL

DIGITAL ZOOM

DETAIL

AGC COLOR SUP

REVERSE

AUTO

OFF

This is useful, especially for a noisy screen.

Set it to <USeR>, you can specify the level.

[

]

MID

OFF

ShUTTeR

POSI/NEGA

PIP

The SHUTTER menu is used to set the fixed fast

electronic shutter or auto fast electronic shutter.

OFF

SeNS-Up

If the brightness of the video signal is too low, the Slow Shutter function will be activated.

Slow Shutter can collect the individual max frame rate to adjust the setting.

FLICkeRLeSS

If set to <oN>, the shutter speed will be fixed to 1/100 second. This will prevent possible

screen distortion due to a mismatch between the vertical sync frequency and the blinking

frequency of the lighting.



If IRIS is set to ELC / SHUTTER to AUTO, FIX, EXT mode / SENSE UP to FIX / AGC to FIX, the <DIS> menu

will be disabled.

XdR

This will correct a brightness difference between different scenes for the optimal visibility.

The higher the value is, the higher the correction level is.

dIS

Automatically compensates for the flicker on the screen.

If set to <oN>, the image will be enlarged with digital zoom as much area as

compensated.

English _ꢀꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

camera setup

dAy/NIGhT

You can specify a recording mode according to the scene.

1. Select <CAmeRA SeT> - <dAy/NIGhT>.

AUTO

2. Select a screen transition mode according to

BURST

DAYNIGHT

BRIGHTNESS

DWELL TIME

NIGHTDAY

BRIGHTNESS

DWELL TIME

OFF

the illumination, and set options as appropriate.



MID

DAY : Fixed to DAY mode, regardless of the

scene.

MID



NIGHT : Fixed to NIGHT mode, regardless

of the scene.

MASK AREA

If BURST is set to <oN>, the burst signal will

output.



AUTO : According to the luminance, this will

switch DAY to NIGHT mode, or vice versa.

MASK AREA



DAYNIGHT / NIGHTDAY : If set to

<SIZE>

<AUTo>, you can specify the brightness

level triggering the mode switch between

DAY and NIGHT as well as the interval.



MASK AREA : If there exists a bright spot

light source in a night scene, you can specify

the size and position as needed.

Any excessively bright area in a night scene

will be masked.

WhITe BAL

If you need to adjust the screen brightness, use the WHITE BALANCE function.

1. Select <CAmeRA SeT> - <WhITe BAL>.

WHITE BAL

2. Select a mode where you set the balance.

DAY/NIGHT

DAY



DAY : You can set the RED, and BLUE value

MODE

RED

BLUE

ATW2

[

]

---- ----

in DAY mode.

---- ----



NIGHT : You can adjust the <WhITe BAL>

according to the ambient luminance.

ꢀꢄ_ camera setup

Download from Www.Somanuals.com. All Manuals Search And Download.

3. According to the speciﬁed recording mode,

select a WHITE BAL mode with necessary

options.

WHITE BAL

DAY/NIGHT

NIGHT

MID

AWC

BRIGHTNESS

MODE



BRIGHTNESS : Specify a brightness level

[

]

---- ----

triggering the switch from DAY to NIGHT

mode.

RED

BLUE

R-GAIN

B-GAIN

---- ----

]

0040

0133



MODE : According to the selected mode,

you can adjust the RED and BLUE color

level.

RED : Adjust the strength of the red color.

BLUE : Adjust the strength of the blue color.

R-GAIN/B-GAIN : Specify the current color temperature manually.



You can set the R-GAIN, and B-GAIN value only in AWC mode.

dIGITAL Zoom

You can set the digital zoom factor and position.

When the zoom factor and position are defined, the digital zoom function will operate.



If you set the digital zoom to a larger factor than the actual enlargement for compensation, the DIS

function will be disabled.

deTAIL

You can adjust the vertical and horizontal sharpness, respectively.

AGC CoLoR SUp

This will adjust the color scheme according to the AGC value.

ReveRSe

This will reverse the signal left to right, top to bottom, or a combination of the preceding.

poSI/NeGA

This will display the video brightness signal either normally or reversely.

pIp

You can view a main image with a sub image on the same screen.

English _ꢀꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

camera setup

pRIvACy ZoNe

You can set up to 12 privacy zones that will be hided for privacy of the subject when recording.

^{For se}Z^leco^tinN^{g a}e^ndS^se^avT^ingU^ep^{ach menu item, refer to "how to use the menu key". (page 22)}

1. Select <mAIN meNU> - <pRIvACy ZoNe>.

◄

►

PRIVACY ZONE

2. Use the four direction ($%_ +) buttons to

select a desired number.

10 11 12

The Zone setup screen appears.

PRIVACY SET

STYLE

MOSAIC1

3. Select the <pIXeL LeveL>.

Specify the pixel unit level for the POSITION

setting.

PRIVACY ZONE SET 1

[

]

PIXEL LEVEL

<POINT>

4. Select <poINT>.

You will see dots on the screen.

5. Use the four direction ($%_ +) buttons to

specify the position for each of the four dots.

6. Select <poSITIoN> and use the four direction

(

$%_ +) buttons to specify the position for

each of the four dots.

7. Save the changes and move to the previous screen and select the <STyLe>.

Select <CoLoR> and pick a desired color.



Setting one or more privacy zone and enabling privacy function will disable the PIP function.

ꢀꢆ_ camera setup

Download from Www.Somanuals.com. All Manuals Search And Download.

oTheRS

You can reset the camera, or select the OSD font color to your preference.

^{For se}F^lecA^tinC^gT^ano^dR^say^vingd^ee^acF^hA^mU^enL^uT^{item, refer to "how to use the menu key". (page 22)}

1. Select <mAIN meNU> - <oTheR SeT>

◄

►

OTHER SET

- <FACToRy deFAULTS>.

The FACTORY DEFAULTS setup screen

appears.

FACTORY DEFAULTS

OSD COLOR

2. Select <ok>.

All the settings will be restored to the factory

default.

However, the language setting will not be

restored.

FACTORY DEFAULTS

CANCEL

oSd CoLoR

You can set the font color of the user interface.

English _ꢀꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

camera setup

SySTem INFo

You can check the system information.

For selecting and saving each menu item, refer to "how to use the menu key". (page 22)

1. Select <mAIN meNU> - <SySTem INFo>.

◄

►

SYSTEM INFO

2. The current system information is displayed.

TYPE

IPB

CAMERA VER.

v1.00_090828



The camera type may different, depend on the video

signal.

LANGUAGe

You can select a language to your preference.

For selecting and saving each menu item, refer to "how to use the menu key". (page 22)

1. Select <mAIN meNU> - <LANGUAGe>.

◄

►

LANGUAGE

*ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

2. Select your preferred language using the

up/down ($%) buttons.



Supported language may different.

ꢁ0_ camera setup

Download from Www.Somanuals.com. All Manuals Search And Download.

network connection and setup

You can set up the network settings according to your network configurations.



Before installing or while using this program, visit the Samsung website www.samsungsecurity.com

and download and upgrade with the latest S/W version available.

CoNNeCTING The CAmeRA To AN Ip RoUTeR WITh The

XdSL/CABLe modem

This is for a small network environment such as homes, SOHO and ordinary shops.

SNB-3000

INTERNET

xDSL또는

Cable모뎀

Cable Modem

xDSL또는

Cable모뎀

Cable Modem

xDSL or

IP공유기

외부원격PC

IP Router

External Remote PC

SNB-3000

로컬PC

Local PC

DDNS서버

DDNS Server

(DataCenter,KOREA)

(Data Center, KOREA)

Configuring the network settings of the local pC connected to an

Ip router

Configuring the network settings of the local PC connected to an IP router, follow the

instructions below.



Select : <Network Neighborhood> <properties> <Local Area Connection>

<properties> <General> <Internet protocol (TCp/Ip)> <properties>

<obtain an Ip address automatically> or <Use the following Ip address>.



Follow the instructions below if you select <Use the following Ip address>:

ex1) If the address (LAN IP) of the IP router is 192.168.1.1

IP address: 192.168.1.100

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

ex2) If the address (LAN IP) of the IP router is 192.168.0.1

IP address: 192.168.0.100

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.0.1

English _ꢁ1

Download from Www.Somanuals.com. All Manuals Search And Download.

network connection and setup

ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1

IP address: 192.168.xxx.100

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.xxx.1



For the address of the IP router, refer to the product’s documentation.

Checking if the Ip router is connected to the xdSL/Cable modem properly

Select <Status> from the Settings menu of the Ip Router



If it is properly connected, <Ip Address>, <Subnet mask> and <Gateway>

provided by your ISP are displayed. Please remember these values because they

are required so that an external remote computer of the IP router connects to the

camera. However, note that certain ISPs change the settings of <Ip Address>,

<Subnet mask> and <Gateway> on a regular basis



If the IP router is not properly connected, press the [Connect] button to try to recon-

nect or check if the settings of the IP router are correct.

CoNNeCTING The CAmeRA To AN Ip RoUTeR WITh

LoCAL AReA NeTWoRkING

This is for a large network environment such as corporate office, building, public office and factory.

SNB-3000

Switch

INTERNET

HUB

IP공유기

IP Router

External Remote PC

외부원격PC

F_방ire_화w_벽all

SNB-3000

로컬PC

Local PC

DDNS서버

DDNS Server

(DataCenter,KOREA)

(Data Center, KOREA)

공유기외부PC

Local PC

Configuring the network settings of the local pC connected to an

Ip router

Configuring the network settings of the local PC connected to an IP router, follow the

instructions below.

ꢁꢀ_ network connection and setup

Download from Www.Somanuals.com. All Manuals Search And Download.



Select : <Network Neighborhood> <properties> <Local Area Connection>

<properties> <General> <Internet protocol (TCp/Ip)> <properties>

<obtain an Ip address automatically> or <Use the following Ip address>.

Follow the instructions below if you select <Use the following Ip address>:

ex1) If the address (LAN IP) of the IP router is 192.168.1.1

IP address: 192.168.1.100

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

ex2) If the address (LAN IP) of the IP router is 192.168.0.1

IP address: 192.168.0.100

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.0.1

ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1

IP address: 192.168.xxx.100

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.xxx.1



For the address of the IP router, refer to the product’s documentation.

CoNNeCTING The CAmeRA dIReCTLy To A dhCp-

BASed XdSL/CABLe modem

INTERNET

xDSL또는

xDSL or

Cable모뎀

외부원격PC

Cable Modem

External Remote PC

SNB-3000

DDNS서버

DDNS Server

(DataCenter,KOREA)

(Data Center, KOREA)

Setting the Ip Router

This is enabled for a modem using DHCP.

1. Set the Static or Dynamic IP address. (pages 36~41)

2. Launch an Internet browser on the local PC connected to the IP Router.

3. Enter the IP Router’s address in the address bar of the browser.

ex) http://192.168.1.1, http://192.168.0.1

or http://192.168.xxx.1



For the DDNS URL address, refer to "To check the DDNS address". (page 43)

English _ꢁꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

network connection and setup

4. When the IP Router is connected, the login window appears and prompts you to

enter the password.



For the login IP and the password, refer to the IP router’s documentation.

5. When done, you will see the setup window of the IP router. In the setup menu,

select “Automatic Conﬁguration-dhCp” for Internet Connection Type.



For the menu location of Internet Connection Type or DHCP selection, refer to the IP router’s

documentation.

6. When done, click the [Save] or [Apply] button to save the settings.

CoNNeCTING The CAmeRA dIReCTLy To LoCAL AReA

NeTWoRkING

Connecting to the camera from a local pC in the LAN

1. Launch an Internet browser on the local PC.

2. Enter the IP address of the camera in the address bar of the browser.

SNB-3000

Switch

HUB

INTERNET

External Remote PC

외부원격PC

SNB-3000

방

irewall

화

벽

로컬PC

Local PC

서

Server

버

(DataCenter,KOREA)

(Data Center, KOREA)



A remote PC in an external Internet out of the LAN network may not be able to connect to the

camera installed in the intranet if the port-forwarding is not properly set or a ﬁrewall is set.

In this case, to resolve the problem, contact your network administrator.

ꢁꢂ_ network connection and setup

Download from Www.Somanuals.com. All Manuals Search And Download.

Ip AddReSS SeTUp

Buttons used in Ip Installer

Item

Description

Model name of the connected camera.

Device Name

Mode

Click the column to sort the list by model name.

However, search will be stopped if clicked during the search.

Displays either <Static> or <Dynamic> for the current network connection

status.

Ethernet address for the connected camera.

MAC(Ethernet)

Address

Click the column to sort the list by Ethernet address.

However, search will be stopped if clicked during the search.

IP address.

Click the column to sort the list by IP address.

However, search will be stopped if clicked during the search.

The factory default is "192.168.1.200".

IP Address

Network setting for the camera.

Protocol

UPnP Status

URL

The factory default is "IPv4".

Cameras with the IPv6 setting will be displayed "IPv6".

This function is not currently implemented.

DDNS URL address enabling access from the external Internet.

However, this will be replaced with the <IP Address> of the camera if

DDNS registration has failed.

English _ꢁꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

network connection and setup

IPv4

IPv6

Scans for cameras with the IPv4 setting.

Scans for cameras with the IPv6 setting.

Scans for cameras that are currently connected to the network.

However, this button will be grayed out if neither IPv4 nor IPv6 is checked.

Auto Set

Manual Set

Exit

<IP Installer> will automatically configure the network settings for you.

You should configure the network settings manually.

Exits the IP Installer program.

STATIC Ip SeTUp

manual Network Setup

Run <Ip Installer.exe> to display the camera search list.

At the initial startup, both [Auto Set] and [manual Set] will be grayed out.



For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not

support this function.

1. Select a camera in the search list.

Find the MAC (Ethernet) address

labeled on the rear of the camera.

Both the [Auto Set] and [manual Set]

buttons will be activated.

2. Click [manual Set].

The MANUAL SET dialog appears.

The default values of <Ip Address>,

<Subnet mask>, <Gateway>, and <hTTp port> of the camera will be displayed.

The default <pASSWoRd> is 4321.

3. In the <AddReSS> pane, provide the

necessary information.

MAC (Ethernet) Address : The MAC

(Ethernet) address of the applicable

camera will be set automatically so you

don't need to input it manually.

ꢁꢄ_ network connection and setup

Download from Www.Somanuals.com. All Manuals Search And Download.

If using an Ip router :



IP Address : Enter an address falling in

the IP range provided by the IP router.

ex) 192.168.1.2~254,

192.168.0.2~254,

192.168.XXX.2~254



Subnet Mask : The <Subnet mask> of

the IP router will be the <Subnet mask>

of the camera.



Gateway : The <Local Ip Address> of

the IP router will be the <Gateway> of the camera.

If not using an Ip router :

For setting <Ip Address>, <Subnet mask>, and <Gateway>, contact your network

administrator.



The values of Device, TCP, UDP, Upload, and Multicast ports can not be changed manually, and

will be adjusted according to the HTTP port value.

4. In the <poRT> pane, provide

necessary information.



HTTP Port : Used to access the

camera using the Internet browser,

defaulted to 80. Use the spin button

to change the HTTP Port value. The

start value of the port is 80, and

increases or decreases by 6 like

10000, 10006, 10012.



Device Port : Used to control the video signal transfer, defaulted to 60001(TCP).



TCP Port : Video signal transfer port using TCP protocols, defaulted to

60002(TCP).



UDP Port : Video signal transfer port using the UDP Unicast method, defaulted to

60003(UDP).



Upload Port : Used to upgrade the software ﬁrmware, defaulted to 60004(TCP).



Multicast Port : Video signal transfer port using the UDP Multicast method,

defaulted to 60005(UDP).

5. Enter the password.

This is the login password for the "admin" user who accesses the camera.

The default password is "4321".

6. Click [ok].

Manual network setup will be completed.

7. When the manual setup including <Ip> is completed, the camera will restart.

English _ꢁꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

network connection and setup

If the Ip router has more than one camera connected

Configure the IP related settings and the Port related settings distinctly with each other.

Category

Camera #1

Camera #2

IP Address

192.168.1.200

255.255.255.0

192.168.1.1

192.168.1.201

255.255.255.0

192.168.1.1

IP related settings

Subnet Mask

Gateway

HTTP Port

Device Port

TCP Port

10000

10001

10002

10003

10004

10005

60001

60002

60003

60004

60005

Port related settings

UDP Port

Upload Port

Multicast Port



If the <HTTP Port> is set other than 80, you must provide the <PORT> number in the address

bar of the Internet browser before you can access the camera.

ex) http://IP address : HTTP Port

http://192.168.1.201:10000

Auto Network Setup

Run <Ip Installer.exe> to display the camera search list.

At the initial startup, both [Auto Set] and [manual Set] will be grayed out.



For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not

support this function.

1. Select a camera in the search list.

Find the MAC (Ethernet) address

labeled on the rear of the camera.

Both the [Auto Set] and [manual Set]

buttons will be activated.

2. Click [Auto Set].

The AUTO SET dialog appears.

The <Ip Address>, <Subnet mask>,

and <Gateway> will be set automatically.

ꢁꢆ_ network connection and setup

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Enter the password.

This is the login password for the

"admin" user who accesses the

camera.

The default password is "4321".

4. Click [ok].

Auto network setup will be completed.

5. The camera will automatically complete

the network setting and restart.

dyNAmIC Ip SeTUp

dynamic Ip environment Setup



Example of the dynamic IP environment

If an IP router, with cameras connected, is assigned an IP address by the DHCP

server

If connecting the camera directly to the xDSL or cable modem using the DHCP

protocols

If IPs are assigned by the internal DHCP server via the LAN

Checking the dynamic Ip

1. From a local PC, run <Ip Installer>

to display a list of cameras that are

assigned <dynamic Ip>.

2. Select a camera in the list, and click

[manual Set] to check the <dynamic

Ip> of the camera.

If you uncheck <dhCp>, you

can change <Ip> or <poRT> to

<STATIC>.

English _ꢁꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

network connection and setup

poRT RANGe FoRWARd (poRT mAppING) SeTUp

If you have installed an IP router with a camera connected, you must set the port range

forwarding on the IP router so that a remote PC can access the camera in it.

manual port Range Forwarding

1. From the Setup menu of the IP router,

select <Applications & Gaming> -

<port Range Forward>.

For setting the port range forward for

a third-party IP router, refer to the user

guide of that IP router.

2. Select <TCp> and <Udp port> for

each connected camera to the IP

router.

Each port number for the IP router

should match that speciﬁed in <Basic>

- <Ip> from the camera's Setup menu.

3. When done, click [Save Settings].

Your settings will be saved.

ꢂ0_ network connection and setup

Download from Www.Somanuals.com. All Manuals Search And Download.

CoNNeCTING To The CAmeRA FRom A ShARed LoCAL

1. Launch <Ip Installer>.

It will scan for connected cameras and

display a list of them.

2. Double-click a camera to access.

The Internet browser starts and

connects to the camera.



You can also access the camera in such way you type the IP address of the found camera in the

address bar of the Internet browser.

CoNNeCTING To The CAmeRA FRom A RemoTe pC vIA

The INTeRNeT

As a remote PC can not directly access <Ip Installer>, you should access the camera in the IP

router network using DDNS URL of the camera.

1. Before you can access a camera in the IP router network, you should have set the

port range forward for the IP router.

2. From the remote PC, launch the Internet browser and type the DDNS URL address

of the camera, or the IP address of the IP router in the address bar.

ex) http://mfffe42.websamsung.net



For the DDNS URL address, refer to "To check the DDNS address". (page 43)

English _ꢂ1

Download from Www.Somanuals.com. All Manuals Search And Download.

web viewer

CoNNeCTING To The CAmeRA

Normally, you would

1. Launch the Internet browser.

2. Type the IP address of the camera in

the address bar.

ex) • IP address (IPv4) : 192.168.1.200

http://192.168.1.200

- the Login dialog should appear.

• IP address (IPv6) : 2001:230:abcd:

ffff:0000:0000:ffff:1111

http://[2001:230:abcd:ffff:0000

:0000:ffff:1111]

If the hTTp port is other than 80

1. Launch the Internet browser.

2. Type the IP address and HTTP port number of the camera in the address bar.

ex) IP address : 192.168.1.200:Port number(10000) http://192.168.1.200:10000

- the Login dialog should appear.

Using URL

1. Launch the Internet browser.

2. Type the DDNS URL of the camera in the address bar.

ex) URL address : http://mfffe42.websamsung.net

- the Login dialog should appear.

Connecting via URL (If the hTTp port is other than 80)

1. Launch the Internet browser.

2. Type the DDNS URL and HTTP port number of the camera in the address bar.

ex) URL address : http://mfffe42.websamsung.net:Port number(10000)

http://mfffe42.websamsung.net:10000

- the Login dialog should appear.

ꢂꢀ_ web viewer

Download from Www.Somanuals.com. All Manuals Search And Download.

To check the ddNS address

The DDNS address consists of: <one of the lower-case letters: c, m, p> + <the last 6 digits

of the MAC (Ethernet) address> + <websamsung.net>

The small letter will be <c> if the first 6 digits of the MAC (Ethernet) address is <00:00:f0>,

or <m> if they are <00:16:6c>, or <p> for <00:68:36>.

ex) - If the MAC (Ethernet) address is 00:00:f0:ff:fe:42: c + fffe42 + websamsung.net =

cfffe42.websamsung.net

If the MAC (Ethernet) address is 00:16:6c:ff:fe:42: m + fffe42 +websamsung.net =

mfffe42.websamsung.net

If the MAC (Ethernet) address is 00:68:36:ff:fe:42: p + fffe42 +websamsung.net =

pfffe42.websamsung.net



The above mentioned addresses are simply examples; do not use any of these for connecting

purposes.

The default user ID is "admin", and the default password is "4321".

1. Enter "admin" in the <User Name>

input box.

2. Enter "4321" in the <password> input

box.

If the password is changed, enter the

changed password instead.

3. Click [ok].

If you have logged in successfully, you

will the Live Viewer screen.



For security purposes, ensure that you change the password in <Basic> - <User>.

The administrator ID, "admin", is ﬁxed and can not be changed.

If you check the "Save this password in your password list" option when your input is done, you

will be logged in automatically without being prompted to enter the login information from next time on.



For this, your computer has installed DirectX 8.1 or later.

You can get a free download of the latest DirectX from http://www.microsoft.com/download.

If you are using Internet Explorer 7.0 or 8.0 as the default web browser, you can view the best

quality image with a screen ratio of 100%. Reducing the ratio may cut the image on the borders.

English _ꢂꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

web viewer

INSTALLING ACTIveX

If connecting to a camera for the first time, you will see the installation message. Then, install the

required ActiveX to access the camera and control the video from it in real time.

For Windows Xp Service pack 2 users

1. Click the installation message that pops

up when you ﬁrst access the camera.

2. Click <Install ActiveX Control...>.

3. The security warning popup appears,

click [Install].

4. When the required ActiveX is installed

properly after your access to the

camera, the Live screen should appear.



For normal installation, set the Block

Popup setting as follows:

Internet Explorer ➝ Tools ➝ Block

Popup ➝ Always allow popups from

the current site(A)

ꢂꢂ_ web viewer

Download from Www.Somanuals.com. All Manuals Search And Download.

USING The LIve SCReeN

Item

Description

SD Search

Setup

Moves to the screen for searching event images from the SD card.

Move to the Setup screen.

About

You can check the firmware version, serial number and manufacturer information.

Resets the Alarm icon. (Alarm and Intelligent Video Analysis icons will disappear.)

Saves the snapshot as an image file in the .jpeg or .bmp format.

Prints out the current image.

Reset Alarm

Capture

Record

Full Screen

Records the current video in avi movie file format.

Displays the Live screen in full screen.

You can set the video format(MJPEG, H.264/MPEG4) for video files.

Note that the menu configuration may differ from your setup of <H.264 & MPEG4

video select> in Video Setup menu.

Video format

On : Activates the specified Alarm Out port.

Alarm output

Off : Deactivates the specified Alarm Out port.

Pulse : Activates the Alarm Out port as much time as specified before deactivating it.

English _ꢂꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

web viewer

Used to retrieve and customize the Camera Setup menu.

Camera OSD

For selecting and saving each menu item, refer to "How to use the menu key". (page 22)

Audio

Viewer Screen

Check the Listen or Speak check box for Audio.

Displays the Live video on the screen.

BACkUp

You can capture, print out, and save the snapshot in the specified path.

To capture the snapshot

1. Click [ ] on the scene to capture.

The Capture dialog should appear.

2. Click [ok].

The screenshot will be saved in the

speciﬁed path.



Default ﬁle path

Windows XP : C:\Program Files\Samsung\SNB-3000\SnapShot\Live

If you want to change the path, click [Set path ( )] and specify a path.

Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\SNB-3000\

SnapShot\Live

On the Windows Vista, Windows 7 system, the path to save is ﬁxed.



The screenshot ﬁle will be named automatically in the format of <IP address_Port

number_YYYYMMDD_hhmmss_index>.

ex) 192.168.0.200_60001_20000114_133857_00

ꢂꢄ_ web viewer

Download from Www.Somanuals.com. All Manuals Search And Download.

To print out the screenshot

1. Click [ ] on the scene to print out.

The Print setup dialog appears.

2. Specify the name of the printer

connected, and click [ok].

To record a video

1. Click [ ] on the scene to record.

2. You will see the Save AVI dialog;

provide the necessary information.



Save path : You can change the

default saving path.



File name : You can change the

default ﬁle name.



HDD minimum free size : If the free

space on the HDD is less than the

recorded space, recording will be forcibly ended.

3. Click [ok].

Recording will start with the display of

<ReC> on the viewer screen.

The video ﬁle will be saved into the

speciﬁed path.

4. If you want to quit recording, click [

]

again.

English _ꢂꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

web viewer



Default ﬁle path

Windows XP : C:\Program Files\Samsung\SNB-3000\VideoClip\Live

If you want to change the path, click [Set path ( )] and specify a path.

Windows Vista, Windows 7 : C:\users\[UserID]\Documents\Samsung\

SNB-3000\VideoClip\Live

On the Windows Vista, Windows 7 system, the path to save is ﬁxed.



The screenshot ﬁle will be named automatically in the format of <IP address_Port

number_YYYYMMDD_hhmmss_index>.

ex) 192.168.0.200_60001_20090903_112334_00

If you want to play an .avi ﬁle, you must have installed the corresponding DivX

codec on your system.

You can get a free download of the DivX from http://sourceforge.net/projects/

ffdshow/.



A specific codec to MPEG4 is required before you can play videos in the MPEG4

format.

You can download the codec for MPEG4 videos from www.samsungsecurity.com.

ꢂꢆ_ web viewer

Download from Www.Somanuals.com. All Manuals Search And Download.

USING The Sd SeARCh vIeWeR SCReeN

1. Click <Sd search> tab in the Live screen.

2. The SD Search Screen appears.

Sd Search viewer Screen layout

Name

Thumbnail Size

Date

Function and description

The thumbnail images are displayed based on the selected size.

You can select the desired date to search for events generated.

You can select the desired time to search the schedule events.

You can select the desired time to search the alarm events.

Schedule

Alarm input

Intelligent video

You can search for events of intelligent video analysis by specifying the time period.

analysis

English _ꢂꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen

ACCeSSING The SeTUp SCReeN

You can configure the default setting, system, overlay, event and network related settings, and

change them as necessary.

1. In the Live screen, click the <Setup>

tab.

2. The Setup screen appears.

deFAULT SeTUp

To configure the video & audio

settings

You can set the video resolution, quality,

CODEC and audio input/output settings.

1. Select <Basic> - <video & Audio>.

The Video & Audio setup screen appears.



Brightness : Adjust the screen

brightness from 1 to 100.



Contrast : Adjust the contrast from

1 to 100.



Resolution : Set the video size of the

MPEG4, H.264, and MPEG ﬁles.

NTSC : 4CIF(704x480),

VGA(640X480), CIF(352X240)

PAL : 4CIF(704x576),

VGA(640X480), CIF(352X288)



Quality : Adjust the picture quality

from 1 to 10.

Frame rate : Select one from 30 fps,

15 fps, 8 fps, 3 fps, and 1 fps.

Bitrate control* : Select CBR (Constant

Bit Rate) or VBR (Variable Bit Rate) for

the compression method.



If selecting VBR, you can not set the target

bit rate.

ꢃ0_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.



Target bitrate : Transfers video signal at a speciﬁed bit rate.

Compression : Adjust the compression rate from 5 through 100 by 5.

Encode priority : Set the video transfer method to Frame rate or Quality.

GOP* size : Select a GOP size between 5 and 15.

Deblock : This will soften the edges between macro blocks.

De-Interlace : You can reduce the grid noise by using the de-interlacing function.

Only available if MPEG4 resolution is set to 4CIF.

If the WDR is set to <OFF> or the MPEG4 resolution is not 4CIF, you cannot enable the

J ^

MPEG4 CODEC’s de-interlacing



Profile : Select Baseline or Main for the H.264 profiling method.

Entropy coding* : Reduces the compression loss due to encoding.

If you set the proﬁle to Baseline, the entropy coding is available only for CAVLC*; if you set it

J ^

to MAIN, the entropy coding is available for both CAVLC* and CABAC*.



Motion estimation : Estimates the movement of pixels by determining the motion vector.

Input gain : You can set the audio input gain from 0 to 10.

Output gain : You can set the audio output gain from 0 to 10.

If the audio input gain is set to 0, no sound is heard.

J ^

2. When done, click [Apply].

Your settings will be saved.

To configure the Ip settings

1. Select <Basic> - <Ip>.

The IP setup window appears.



IP conﬁguration : Set the IP and port

settings for the camera.

IP type : Select one from <Static

Ip>, <dynamic Ip>, and <pppoe

Ip>.



If you select <PPPoE IP>, you can

provide the optional ADSL IP and

password. However, the multicast items

(multicast address, port, TTL) for VNP

and RTP will disappear.

English _ꢃ1

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen

MAC address : Displays the Ethernet MAC address.

This is used for creating a DDNS address.

IP address : Displays the current IP address.

Subnet mask : Displays the <Subnet mask> for the set IP.

Gateway : Displays the <Gateway> for the set IP.

DNS server : Displays the DNS(Domain Name Service) server address.

HTTP webserver port : HTTP port used to access the camera via the web

browser. The default is 80(TCP).

Upload port (TCP) : Used to upgrade the software ﬁrmware, defaulted to 60004(TCP).



IPv6 conﬁguration : Obtains the IPv6 address to access the IPv6 network.

VNP conﬁguration : Set a port used to transfer video signals with the Samsung

protocols.

Device port (TCP) : Used to control the video signal transfer, defaulted to 60001(TCP)

TCP streaming port : Video signal transfer port using TCP protocols, defaulted

to 60002(TCP).

UDP streaming port : UDP Port used to transfer video signal with the UDP

Unicast protocols. The default is 60003(UDP).

Multicast address : IP address used to transfer video signal with the UDP

Multicast protocols.

The default is 225.128.1.128, and if you want to change the address, specify it

ranging from 224.0.0.0 to 239.255.255.255.

Multicast port : UDP Port used to transfer video signal with the UDP Multicast

protocols. The default is 60005(UDP).

TTL* : Set the TTL for the VNP packet.

The default is 63, and if you want to change the address, specify it ranging from

0 to 255.



RTP conﬁguration : You can set the RTP protocol.

RTSP port : You can set the RTSP port.

Streaming port : Used to transfer video signal with the RTP protocols.

The default range is between 61000 and 61999.

Multicast address : IP address used to transfer video signal with the RTP

protocols.

Multicast port : Used to transfer video signal with the RTP-protocol multicasting.

TTL* : You can set the TTL for the RTP packet.

2. When done, click [Apply].

Your settings are saved and the system restarts.

The currently opened web browser will be closed.



If the IP router has more than one camera connected, you should conﬁgure IP and port settings

differently with each other.

ꢃꢀ_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.

To set the user account

1. Click <Basic> - <User>.

The User setup window appears.



authenticate the login by the user.

If you select <enable>, the user

should have gone through the

<disable>, every user can access

the system without the login authentication, having the ordinary user permissions.

When done, click [Apply].

Your settings will be saved.

2. Add users or edit user ID or password.



User login ID/password list : Displays a list of accessible users ID, passwords, and

ratings.

You can add up to 10 users.

The admin ID is "admin".

The password for the admin ID can be changed, but not added or deleted.

User Registration

1. From the User setup window, click

[Insert].

The Register User window appears.

2. Provide the <User Id>, <password>,

and <Conﬁrm password>,

respectively. You can enter up to 9

alphanumeric or special characters

(some excluded) for the user ID and

password, respectively.

3. Select a user level.

Select either <operator> or <User> for a new user's permission.

4. Click [Apply].

The user registration is completed.



An existing user ID can not be added duplicate.

Neither admin ID nor guest ID can be registered.

English _ꢃꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen

To edit a registered user account

1. From the User setup window, select a

user ID to change.

2. From the User setup window, click

[modify].

The Modify user window appears.

3. Change the <User Id>, <password>,

<Conﬁrm password>, and <Level> as

you wish.

4. Click [Apply].

The selected user ID will be changed.

To delete a user Id

1. From the User setup window, select a user ID to delete.

2. From the User setup window, click [delete].

The selected user ID will be deleted.



About the user permission

Administrator : Can use all functions (change/control settings).

Operator : Can use only the functions available in the Live Viewer.

User : Can only view the video on the Live Viewer.

To set the display language

1. Click <Basic> - <Language>.

The Language setup window appears.

You can select one from 7 languages

(English/Korean/Chinese/French/Italian/

Spanish/German).

2. When done, click [Apply].

The selected language will be applied.

ꢃꢂ_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.

SySTem SeTUp

To set the date/time

You can obtain the current system time from the NTP server or your PC for your time

setting.

1. Select <System> - <date & Time>.

The Date & Time setup window

appears.

2. If you select Manual, input the date and

time manually.

Your settings will be saved.



Current system time : The speciﬁed

time in System Time Setup will be

applied.



System time setup : You can synchronize the system time with the NTP server (time

server) or your PC, or specify it manually.



You can specify the time between January 1, 2000 and December 31, 2037.

To set the system time

1. Select a desired address in <Address>

or select <Synchronize with pC

viewer>.

2. If you select Manual, input the date and

time manually.

3. Click [Apply].

The speciﬁed system time will be applied.



<NTP Server IP> is provided by a public agency, the list of which is subject to change from time

to time.



In a local network, a separate NTP server must be manually deﬁned.

The current time can vary depending on the computers regional (GMT and DST) and country

(PC time conﬁguration) settings.

English _ꢃꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen

To check the log information

Select <System> - <Log>.

The Log information list appears.



System log list : Shows the log

information about the system changes

along with time and IP address.

System started: When the camera

turns on

User login: When the user logs in to the camera

System reset: When the camera restarts

Network is up: When accessing the network

Network is down: When not accessing the network

Video param. changed: When the video related parameters are changed

System time changed: When the system time is changed

Network conﬁguration change: When the network related conﬁgurations are changed

Alarm occurrence 1, 2: When an alarm is generated

Intelligent Video Analysis occurrence: When an intelligent video analysis event is generated.

FTP send error: When FTP transfer failed

SMTP send error: When sending e-mail message through SMTP server fails.



The maximum of 2000 logs can be recorded.

If the log number is over 2000, the log in the bottom of the log list will be replaced with a new log.

To update the software

Select <System> - <Software update>.

The Software update window appears.

how to update the software

1. From the software update window,

click [Browse…].

The Open dialog appears.

2. Select an updatable ﬁle and click

[open].

3. From the software update window,

click [Install].

The selected ﬁle will be unzipped with a

start of the update.

It may take a several minutes to complete the update.

ꢃꢄ_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.

4. When the software update is completed, you will be prompted to restart the system.

5. Click [ok] to restart the system.

Since the current connection is disconnected, you have to connect to the system again.



If the network is disconnected, the power supply fails, or the PC abnormally operates during the

update, the system does not work at all.

To reset the system

Restart or reset the system if it does not

work properly or causes a problem.

Select <System> - <Reset>.

The Reset window appears.



Restart : Restarts the system.



Factory default : Resets the system

settings to the factory defaults with following two options:

Except network parameter : Resets all settings except for the Network Parameters.

All : Restores all settings to the default.

This works the same as pressing the [ReSeT] button on the rear of the camera.



After the system is reset or restarts, you should try to connect to the camera again.

It takes several minutes until the system completes rebooting. Wait until the system rebooting is

completed and try to connect again.



After executing <Factory default>, you must run the <IP Installer.exe> program to change the

basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to

the Internet.

To set the hTTpS

1. Select <System> - <hTTpS>.

The HTTPS setup window appears.



Secure connection system : Select

a secure connection system to use.

To use the secure connection mode

requiring the public certiﬁcate for the

secure connection system, you must

have installed a signed certiﬁcate

issued by a certiﬁcate authority on

your system.



Install a public certiﬁcate : To install the certiﬁcate to camera, you need to type a

certiﬁcate name (it can be arbitrarily assigned by user), certiﬁcate ﬁle issued from

the authority and a key ﬁle. When done, click [Install].

If the certiﬁcate is installed successfully, the user-deﬁned certiﬁcate name will be

displayed. Also, the option button of <hTTpS (Secure connection mode using

the public certiﬁcate)> in the upper side becomes activated.

English _ꢃꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen



To access the camera using HTTPS mode, you have to type the IP address for the camera in the

form of “https://<Camera_IP>”.

2. When done, click [Apply].

The web viewer will switch to the set secure connection system.

To Set Ip Filtering

1. Click <System> - <Ip ﬁltering>.

The IP Filtering Setup screen appears.



Basic policy : You can select the IP

ﬁltering policy.

If you set to Permission, the web

server allows all attempting IP

addresses except the addresses

added in the refusal list.

If you set to Refusal, the web server allows only IP addresses added in the

permitted list and rejects all other IP addresses.

To apply the IP ﬁltering policy, click [Apply] button.

2. Enter the IP address and subnet mask into the IP ﬁeld to be allowed or rejected.

The Filtering range* will differ depending on speciﬁed IP address and subnet mask.

oveRLAy SeTUp

You can display text on the screen.

To set the text

1. Select <overlay> - <overlay text>.

The Overlay Text setup window

appears.

2. When done, click [Apply].

Your settings will be saved.



Overlay text settings : If you select

<disable>, the overlay text will not

be displayed; If selecting <enable>, it will display on the screen.



Show date : Set to display the date information on the bottom screen.

Output Format : Select a display format of the date information.

YYYY-MM-DD : Year-Month- Day / MM-DD-YYYY : Month-Day-Year /

DD-MM-YYYY : Day-Month-Year

ꢃꢆ_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.



Show time : Set to display the time information on the bottom screen.

Output Format : Select a display format of the time information.

24hr : Displays the time in the 24-hour format.

12hr : Displays the time in the 12-hour format.



Text color : Select black or white for the text color.

Background color : Select black or white for the background color.

eveNT SeTUp

To set the event transfer function

You can set the FTP/email server (SMTP)

to transfer the alarm images present in the

camera, in case an alarm event occurs.

Select <event> - <Transfer setup>.

The Image transfer setup window appears.



For more information on commercial

SMTP services, contact the SMTP service

provider.

To test the FTp transfer

Click [Test].

This will test if the image is transferred to the

specified FTP server properly.

When the test on the FTP server connection

and transfer is done, a message of

<( verified )> will be displayed.

You will see an error message if the test

fails. If this is the case, check the FTP server

status or the settings again.



FTp transfer : With this, you can transfer alarm images to the FTP server. If the initial FTP

appears.

server setting and the connection status are not veriﬁed, the <( Not veriﬁed )> message

English _ꢃꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen

Use passive mode : Select this option when the passive mode connection is

inevitable due to the ﬁrewall or FTP server setting.

FTP server address : Enter the IP address of a FTP server to which an alarm image

will be transferred.

Upload path : You can specify the path of the FTP directory to which you will

transfer an alarm image.

You can specify the path by just typing </directory name> or <directory name> in

this ﬁeld.

If nothing is speciﬁed, the path will be defaulted to the root directory of the FTP

server.

Port : The FTP port is defaulted to 21. This value can be changed according to the

FTP server setting.

User ID : Provide the user account ID to access the FTP server.

Password : Provide the user account password to access the FTP server.



e-mail(SmTp) transfer : With this setting, you can transfer alarm images to the email

server. This function is available only for the SMTP email server. When the initial SMTP

server setting and connection are not verified, the <Not verified> message appears.

SMTP server address : Enter the SMTP server address to use when you send an

email.

ex) 10.240.56.228

Port : Enter a port number to use when you send an email. The default is 25.

User ID : Provide the user account ID to access the SMTP server.

Password : Provide the user account password to access the SMTP server.

E-mail sender : Enter the address of the email sender. If the sender address is

incorrect, the email from the sender may be classiﬁed as SPAM by the SMTP

server and may not be sent.

E-mail receiver : Enter the address of the email receiver.

Title : Enter the subject of the email to send.

Message : Enter the content of the email to send.

To test the email transfer

Click [Test].

This will test if the image is transferred to the

specified SMTP server properly. When the

test on the SMTP server connection and

transfer is done, a message of <( verified )>

will be displayed.

You will see an error message if the test

fails.

If this is the case, check the SMTP server

status or the settings again.

ꢄ0_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.

To setup the record

1. Click <event> - <Record setup>.

The Record setup window appears.

2. To complete the setting, click the

[Apply] button.

The settings are saved.



SD card : Enables you to verify data

saved on the SD memory card and

format the memory card itself. It

is possible to set to automatically delete movie clips recorded before a certain

period of time (e.g. 1 week, 1 month, or 1 year).



Options : Determine whether or not you wish to receive Email notiﬁcation of

insufﬁcient capacity warnings.

To set an alarm image

You can configure to send message via FTP/E-mail (SMTP) or to save recording into the

SD memory card.

Select a transfer method when an event occurs or the schedule transfer function is activated.

1. Select <event> - <Alarm image>.

The Alarm Image setup window

appears.



Transfer mode : You can select

alarm message notiﬁcation method

among FTP/E-mail transfer and SD

Card recording.

FTP transfer : The image is sent to

the speciﬁed FTP address.

E-mail transfer : The image is sent to the speciﬁed email address.

SD Card Record : Saves images into the SD memory card.

If an SD memory card is not inserted, the corresponding button will be disabled.

M ^

In this case, insert the SD memory card into the slot and refresh to enable the button.

If the SD memory card is ejected while the button is checked, the camera automatically

J ^

restarts.



Transferred image naming setup : You can set the ﬁle name of an alarm image

to be sent when an alarm is triggered or during the scheduled transfer.

pre/post alarm image : You can set to save the pre or post alarm image.

Number of image : The frame rate per second can be one among 1, 2, 3, and 5.

Pre-alarm duration : The pre alarm duration can be one among 5 seconds, 10

seconds, 15 seconds, and 30 seconds. You can send a pre-alarm image of up

to 30 seconds before the alarm is triggered.

(The max time differs, depending on the frame rate)

English _ꢄ1

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen

Post-alarm duration : The post alarm duration can be one among 5 seconds, 10

seconds, 15 seconds, and 30 seconds. You can send a post-alarm image of up

to 30 seconds after the alarm is triggered.

(The max time differs, depending on the frame rate)



The pre/post alarm duration is not available in SMTP transfer mode.

Only one image at the corresponding time will be transferred.

2. When done, click [Apply].

Your settings will be saved.

To set the alarm input

1. Select <event> - <Alarm input 1> or

<Alarm input 2>.

The Alarm Input setup window appears.

2. When done, click [Apply].

Your settings will be saved.



Input device setup : Select an input

type according to the characteristics

of the alarm sensor on the rear of the

camera.

Off : Turns off the alarm input setting.

NO (Normal Open) : It is normally open, but if it is closed, an alarm will be

triggered.

NC (Normal Close) : It is normally closed, but if it is open, an alarm will be

triggered.



Activation time : You can set a time to execute a speciﬁc command when an

alarm occurs.

Always : Always executes the speciﬁed command when an alarm occurs.

Only scheduled time : Activates notiﬁcation as conﬁgured only when alarm

events occurred during the speciﬁed time period.

Action : You can set an action to execute when an alarm occurs.

Alarm output : Set the alarm output port to which the alarm signal is transferred.

Output duration : Set the period of time to output the alarm signal to the

speciﬁed alarm output port when an alarm occurs.

If a new alarm event is detected during the alarm output, the delay time is

recalculated based on the detection time of the recent alarm.

Alarm image transfer : If you select <on>, you can transfer JPEG images to a

registered address via FTP or SMTP server or save images into the SD memory card

according to the setting in <event> - <Transfer setup>.

ꢄꢀ_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.

To Set Intelligent video Analysis

1. Click <event> - <Intelligent video

analysis>.

The Intelligent Video Analysis screen

appears.

2. When done, click [Apply].

Your settings will be saved.



Iv analysis function : Activated if

<disable> is selected.

<enable> is selected, deactivated if



If camera is capturing a close

object, the video analysis capability

may degrade.



In the following cases, the video

analysis function may not produce

proper result on conﬁgured event

and motion detections.

- The subject color or brightness is

similar to the background

- Multiple random movement continues due to scene change or other reasons.

- When object that is ﬁxed continues to move in the same position.

- An object hides other objects behind.

- 2 or more objects overlaps or 1 object splits into multiple objects.

- Too fast object (for detection, one object should be found overlapping between

contiguous frames).

- Reﬂection / blur / shadow due to direct sunlight, illumination, or headlamp

- In severe snow, rain, wind or in dawn / dusk

- Moving object approaches to the camera too close



overlay : If <enable> is selected, conﬁgured event rules and motion frame

are displayed on the Live screen. Selecting <disable> will not display overlay

information.



Motion frame is displayed in two types on the Live screen.

Green frame – indicates the moving object

Red frame – Temporarily displays the moving object detected by the conﬁgured event

rules.



Sensitivity : Sets the sensitivity of the intelligent video analysis.

Sensitivity : Select the sensitivity among <very high>, <high>, <Normal>,

<Low>, and <very low>.

When selected with <very high>, the intelligent video analysis functions on the

smallest motion detection.

English _ꢄꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen



Set rules

You can set the event rules.

Virtual line based rules : You can conﬁgure event rules for up to 3 virtual lines.

Pass : Event is generated if a moving object crosses the virtual line in the speciﬁed

direction (, , )

Deﬁned area based rules : You can conﬁgure event rules for up to 3 user-

deﬁned areas.

 Entering : Event is generated if a moving object enters the deﬁned area from

outside to inside.

 Exiting : Event is generated if a moving object exits the deﬁned area from

inside to outside.

 Appearing : An object that has not been existed in the area until the previous

frame suddenly appears inside the conﬁgured area, not passing the border

 Disappearing : An object that has been existed in the area until the previous

frame suddenly disappears, not passing the border.

Entire area based rules : You can conﬁgure event rules for the entire video area.

 Appearing: An object that has not been existed until the previous frame

appears in the area.

 Disappearing: An object that has been existed until the previous frame

disappears from the area.



Scene Change: This event is generated by a complete scene change, such as

camera veiled by hand or changed camera’s aiming, etc.

Object size: The maximum object size of motion detection for each event

generation. The minimum size can be adjusted in 5 levels.

Minimum size (the minimum rectangular motion detection area): Step 1: 6x6 (pixel),

Step 5: 50x50 (pixel)

Maximum size (the maximum rectangular motion detection area): Step 1: 60x60

(pixel), Step 5: 320x240 (pixel)

The initial setup for the minimum is 6x6 and for the maximum is 320x240.

ꢄꢂ_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.



Activation time : Sets the operation time of the intelligent video analysis.

Always : Conﬁgured action is performed whenever an intelligent video analysis

event occurs.

Only scheduled time : Conﬁgured action is performed when intelligent video

analysis event occurs during the speciﬁed time period.

Action : You can conﬁgure the action for an intelligent video analysis event.

Alarm output : Sets the alarm output port for the signaling the intelligent video

analysis event.

Output duration : Sets the alarm signal dwell time to the Alarm Output port on

an intelligent video analysis event.

When another intelligent video analysis event follows the previous one, the

output duration time is reset based on the most recent event.

Alarm image transfer : If selected <enable>, depending on your setting of

<event> - <Transfer setup>, the image in JPEG format will be sent to the

registered address via FTP or e-mail (SMTP), or saved in the SD memory card.

To set the scheduled transfer

You can set to transfer the JPEG image to the FTP/SMTP server saved in the SD memory

card at a specific interval.

1. Select <event> - <Schedule>.

The Schedule Transfer setup window

appears.



Schedule transfer function :

If selecting <enable>, the schedule

transfer function will be activated;

if selecting <disable>, it will be

deactivated.



Transfer interval : You can set the

time interval to transfer images.

You can set the unit of the interval to <seconds> or <minutes>; you can also set to

transfer one image per 5/15/30/45/60 seconds, or one per 5/15/30/45/60 minutes.



Activation time : You can set a time to execute a specific command when a sched-

ule transfer event occurs.

Always : Always sends an image at the set interval.

Only scheduled time : Periodically transfers image only during the speciﬁed time

period.

2. When done, click [Apply].

Your settings will be saved.

English _ꢄꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

setup screen

NeTWoRk SeTUp

To set the video transfer mode

You can control the transfer rate according to the video transfer mode and network speed.

1. Select <Network> - <Streaming type>.

The Video Transfer setup window

appears.

2. When done, click [Apply].

Your settings will be saved.



vNp streaming : You can set the

Samsung Protocol (VNP) for the streaming service.

Protocol : Select a video transfer protocol from TCP*, UDP (Unicast)*, and UDP

(Multicast)*.



Speaking to the camera unit through microphone is not supported.

Multicast backbone (MBone) is not supported; you can access the camera only in the

multicast local network environment.



RTp streaming : You can set the RTP Protocol or the streaming service.

Protocol : Select a video transfer protocol from UDP (Unicast) and UDP (Multicast).

To set the ddNS

DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address

of a camera into a general Host Name so that the user can easily remember it and enables

connecting a camera with a fixed Host Name even if the IP address of the camera may be

dynamically changed.

1. Select <Network> - <ddNS>.

The DDNS setup window appears.

2. When done, click [Apply].

Your settings will be saved.



For checking the DDNS address, refer to "To check the DDNS address". (page 43)

ꢄꢄ_ setup screen

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

pRoFILe

CAMERA SETUP MENU

STANDARD

ITS

BACKLIGHT

DAY/NIGHT

GAMING

Parent Menu

Sub-menus

ALC

OFF

ALC

OFF

ALC

WDR

ALC

OFF

ALC

OFF

ALC

IRIS

LENS

LEVEL

BACKLIGHT

(F.FAST)

MOTION

NORM

SLOW

---

DNR

SHUTTER

SENSE UP

XDR

MID

OFF

MID

OFF

AUTO 1/250

OFF

AUTO X4

AUTO X2

AUTO X4

MID

AUTO

DAY

AUTO

DAY

DAY/NIGHT NIGHT

DAY

OFF

DAY

BURST

OFF

DAY/NIGHT

DAY

DAY/NIGHT

DAY

MODE

RED

ATW2

ATW1

BLUE

WHITE BAL

NIGHT

MID

ATW2

MID

ATW2

BRIGHTNESS Custom Setting

Custom Setting

OFF

Custom Setting

OFF

MODE

OFF

RED Custom Setting

BLUE Custom Setting

Custom Setting

DETAIL

English _ꢄꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

TeRmINoLoGy



GOP : You can set between 5 and 15 for the MPEG4 and H.264 CODEC.

The default is 15, and if set to 15, one I-Frame will be output per 15 frames as one I-Frame

and 14 P-Frames constitute the GOP.

The lower the GOP size is, the better the quality is; however, the bit rate as well as the data

size will increase, causing a lower of the fps. GOP(Group of Pictures) is a set of video frames

for MPEG4 and H.264 format compression, indicating a collection of frames from the initial

I-Frame (key frame) to the next I-Frame. GOP consists of 2 kinds of frames: I-Frame and

P-Frame. I-Frame is the basic frame for the compression, also known as Key Frame, which

contains one complete image data. P-Frame contains only the data that has changed from

the preceding I-Frame.



Entropy coding : Data transfer technology used to reduce the compression loss from encoding.

CAVLC (Context-adaptive variable-length coding): Records a higher compression loss

rate than CABAC.

CABAC (Context-adaptive binary arithmetic coding): Shows a lesser compression loss than

CAVLC.



Bitrate Control

CBR(Constant Bitrate)

This will transfer video data in an equal size at all times, regardless of the video

complexity. The video quality may be deteriorated, depending on the video complexity.

VBR(Variable Bitrate)

The amount of video data to transfer may differ, depending on the video complexity. This

enables receiving video data in an equal quality at all times.



TTL : TTL stands for “Time To Live”, which you can specify to prevent loss of data packet that

passes through multiple-staged routers. Each router decreases the TTL value by one each

time a packet passes it through; If the TTL value reaches 0, the packet cannot further pass

through a router.

TCP : It is a general purpose protocol used for transmission that requires reliability. With

constant communication between the sender and recipient, it provides high reliability against

transmission data loss; however, it has imitation to transmit a large amount of data in real time

at a high speed.

It enables reliable data transmission over xDSL and cable network at a relatively slow speed.



UDP (Unicast): It refers to a system that transmits data between only one transmitter and one

receiver (1:1).

UDP (Multicast): It refers to the data transfer protocol in one-to-many (1:N) between the trans-

mitting and receiving terminals; although it alleviates the network load, it requires <Multicast>

router.

For more information such as whether the network over which the camera is installed sup-

ports <Multicast>, contact the network administrator.



UDP : It is a protocol appropriate to transmit a large amount of data such as multimedia data at a

high speed. However, with its nonconnection structure, it records a higher transmission efficiency

than TCP especially in a high LAN environment faster than 100Mbps.

ꢄꢆ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.



Filtering range

The filtering range is calculated based on IP address and subnet mask provided by user as

follows:

The subnet value deﬁnes the number of masked bits, which will mask the IP address that

is converted into 32-bit binary; rest of masked out bits are ignored to produce the range

as shown below.

Ex) IP address : 128.128.128.128



If the Subnet is set to 8, converted IP is 1000 0000.1000 0000.1000 0000.1000 0000

and the subnet directs to ﬁnd matches from the ﬁrst bit to the 8th bit, produces the

ﬁltering range of 1000 0000.???? ????.???? ????.???? ????, which will be converted

back to IP address range of 128.0.0.0 ~ 128.255.255.255.

 If the Subnet is set to 10, converted IP is 1000 0000.1000 0000.1000 0000.1000

0000 and the subnet directs to ﬁnd matches from the ﬁrst bit to the 10th bit, produces

the ﬁltering range of 1000 0000.0000.10?? ????.???? ????.???? ????, which will be

converted back to IP address range of 128.0.0.0 ~ 128.191.255.255.

 If the Subnet is set to 20, converted IP is 1000 0000.1000 0000.1000 0000.1000 0000

and the subnet directs to ﬁnd matches from the ﬁrst bit to the 20th bit, produces the

ﬁltering range of 1000 00001000 0000.1000 ????.???? ????, which will be converted

back to IP address range of 128.128.128.0 ~ 128.128.143.255.

 If the Subnet is set to 30, converted IP is 1000 0000.1000 0000.1000 0000.1000 0000

and the subnet directs to ﬁnd matches from the ﬁrst bit to the 30th bit, produces the

ﬁltering range of 1000 0000.1000 0000.1000 0000.1000 00??, which will be converted

back to IP address range of 128.128.128.128 ~ 128.128.128.131.

 If the Subnet is set to 32, converted IP is 1000 0000.1000 0000.1000 0000.1000 0000

and the subnet directs to ﬁnd matches from the ﬁrst bit to the 32th bit, produces the

ﬁltering range of 1000 0000.1000 0000.1000 0000.1000 0000, which will be converted

back to IP address of 128.128.128.128.

English _ꢄꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

SpeCIFICATIoNS

Description

Item

NTSC

PAL

Camera

Color/BW

Type

Color

Device

1/3" Super-HAD PS CCD

811 x 508

Image

Total

Effective

795 x 596

752 x 582

Pixels

768 x 494

System

Horizontal Frequency

Vertical Frequency

Progressive

Scanning

15.734 Hz

15.625 Hz

50 Hz

59.94 Hz

Sens off : 0.12 Lux(15 IRE), 0.2 Lux(30 IRE),

0.4Lux(50 IRE)@F1.2

Color

B/W

Sens up x512 : 0.00023 Lux(15 IRE), 0.0005 Lux(30 IRE),

0.0008Lux(50 IRE)@F1.2

Min. Scene

Illumination

Sens off : 0.012 Lux(15 IRE), 0.02 Lux(30 IRE),

0.04Lux(50 IRE)@F1.2

Sens up x512 : 0.000023 Lux(15 IRE), 0.00005 Lux(30 IRE),

0.00008Lux(50 IRE)@F1.2

Number of Privacy Zone

Day/Night

WDR

Extended Dynamic Range

D-Zoom

PIP

High Speed Shutter

Flickerless

Sens Up

BLC

AGC

ELC

Camera ID

White Balance

Digital Noise Reduction

Digital Image Stablization

Etc. Function

12 ea

Day/Night/AUTO(Hard Method)

Off/On (x128)

Off/On (x160)

Off/On (Level Setting)

x1 ~ x16 (x0.1 STEP)

Off/On (Advanced)

1/60 ~ 1/10Ksec

Off/On

1/50 ~ 1/10Ksec

Functions

x2 ~ x512

Off/On (Area Setting)

Off/On (Max.Level Setting)

Off/On ( ~ 1/200Ksec)

Off/On (Max.54ea/2Line)

ATW1/ATW2/AWC/3200K/5600K

Off/On (Adaptive 3D+2D)

Off/On

Detail, Reverse(H/V), Posi/Nega

ꢅ0_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

Description

Item

Horizontal

NTSC

600 TV Lines

PAL

Resolution

Vertical

350 TV Lines

VBS 1.0Vp-p

about 52 dB

MANUAL/AI(VIDEO/DC)

CS/C

Embedded Linux

32M byte

Video Output Video Output

S/N Ratio

Lens Drive Type

Mount Type

Lens

Flash memory

RAM

256M byte

TI Davinci

Network

Board

Hardware

DSP

Ethernet

PoE

RJ-45 (10/100BASE-T)

Yes (IEEE802.3af)

2 ea

Input

Alarm

Video

Output

2 ea

H.264 / MPEG4 / MJPEG Multiple Codec

Compression

(H.264 / MPEG4 selectable)

Simultaneous Dual Streaming

4CIF

VGA

CIF

704x480

704x576

352x288

Resolution

640x480

352x240

Frame Rate

Quality

30, 15, 8, 3, 1 fps

1 ~ 10 level

25, 13, 6, 3, 1 fps

Audio

OSD

Compression

Full Duplex, 64kbps, 8KHz sampling

OSD menu on Video

Camera Control and Adjustment (Menu enter/exit, move by Web UI)

* Some key adjustment menus will be supported by CGI API.

Very High, High, Normal, Low, Very Low

Intelligent

Video

Analysis

Detection

Sensitivity

English _ꢅ1

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

Description

Item

NTSC

PAL

IPv4 / IPv6

TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP,

HTTPS, SSL, DHCP

IPv4

IPv6

Network

Protocol

PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2),

ARP, DNS, DDNS, VSIP

Protocol

Streaming

Security

DDNS

TCP/IP, HTTP, HTTPS, SSL, DHCP

Unicast (TCP, UDP), Multicast (UDP)

HTTPS Login Authentication

Digest Login Authentication

Supporting Samsung DDNS and Public DDNS services

Max 10 Users at Unicast (TCP, UDP) Mode

Maximum User Access

Max 20 Users at Multicast (UDP) Mode

Live Monitoring, Alarm I/O control, OSD menu control,

SETUP

Administrator

Connection

User Access

Level

Operator

User

Live Monitoring, Alarm I/O control

Live Monitoring

JPEG Image transfer : FTP, SMTP, SD Card

Notification : notify to viewer or by E-mail (one image

attachment)

Alarm Input

Event

Intelligent Video Analysis

Management Detection

Alarm Out

Schedule

JPEG Image transfer : FTP, SMTP, SD Card

Windows XP, Windows VISTA, Windows 7

Internet Explorer 6.0 or Higher

E/F/G/S/I/C/K

Supported OS

Web Browser

Viewer

(Default)

Supported Browser

UI Language

S/W upgrade

Support

Quicktime, VLC player

Video Player RTP/RTSP streaming

Video

Samsung iPOLiS

Management Video Management System

Software

3rd Party S/W appliction

Application

IP Installation

IP Installer Application for All Samsung IP Devices

ꢅꢀ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

Description

Item

NTSC

PAL

Provides functionality to control cameras

and set/retrieve internal parameter values.

Get JPEG image or MJPEG stream

Alarm In/Out control

HTTP API

CGI Command

SDK

RTP/RTSP API

ActiveX

RTP Header, RTSP Command Document

ActiveX API for viewing data streams from IP camera.

AC24V 10%(60Hz 0.3Hz)/ DC12V+10%/-5% /

Power

PoE (Power over Ethernet)

Power Consumption

Operating Temp.

Operating Humidity

Dimension

About 8W

-10˚C~50˚C

~90%

W72 X D139 X H60

About 435g

Weight

English _ꢅꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

FRAme RATe (NTSC)



Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1)

H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),

GOP size(15), Deblock(ON), Proﬁle(Baseline), Entropy coding(CAVLC), Motion

estimation(HPel)

MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),

GOP size(15)

❖ mpeG4 (4CIF)

Frame Rate

30 FPS

15 FPS

8 FPS

3 FPS

1 FPS

Quality

4239 Kbps

2765 Kbps

1290 Kbps

737 Kbps

221 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

23 FPS

15 FPS

7 FPS

4 FPS

1 FPS

3686 Kbps

24 FPS

2304 Kbps

15 FPS

1075 Kbps

7 FPS

614 Kbps

4 FPS

184 Kbps

1 FPS

3072 Kbps

1843 Kbps

860 Kbps

492 Kbps

147 Kbps

25 FPS

15 FPS

7 FPS

4 FPS

1 FPS

2396 Kbps

26 FPS

1382 Kbps

15 FPS

645 Kbps

7 FPS

369 Kbps

4 FPS

111 Kbps

1 FPS

1659 Kbps

922 Kbps

430 Kbps

246 Kbps

74 Kbps

27 FPS

15 FPS

7 FPS

4 FPS

1 FPS

1336 Kbps

29 FPS

691 Kbps

15 FPS

323 Kbps

7 FPS

184 Kbps

4 FPS

55 Kbps

1 FPS

1133 Kbps

576 Kbps

269 Kbps

154 Kbps

46 Kbps

30 FPS

15 FPS

7 FPS

4 FPS

1 FPS

922 Kbps

30 FPS

461 Kbps

15 FPS

215 Kbps

7 FPS

123 Kbps

4 FPS

37 Kbps

1 FPS

691 Kbps

346 Kbps

161 Kbps

92 Kbps

28 Kbps

30 FPS

15 FPS

7 FPS

4 FPS

1 FPS

461 Kbps

30 FPS

230 Kbps

15 FPS

108 Kbps

7 FPS

61 Kbps

4 FPS

18 Kbps

1 FPS

ꢅꢂ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ h.264 (4CIF)

Frame Rate

30 FPS

15 FPS

8 FPS

3 FPS

1 FPS

Quality

2298 Kbps

1229 Kbps

737 Kbps

369 Kbps

147 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

19 FPS

10 FPS

6 FPS

3 FPS

1 FPS

1751 Kbps

19 FPS

1198 Kbps

13 FPS

645 Kbps

7 FPS

369 Kbps

4 FPS

111 Kbps

1 FPS

1536 Kbps

1075 Kbps

538 Kbps

307 Kbps

92 Kbps

20 FPS

14 FPS

7 FPS

4 FPS

1 FPS

1352 Kbps

22 FPS

897 Kbps

15 FPS

430 Kbps

7 FPS

246 Kbps

4 FPS

74 Kbps

1 FPS

1129 Kbps

691 Kbps

369 Kbps

184 Kbps

55 Kbps

25 FPS

15 FPS

8 FPS

4 FPS

1 FPS

960 Kbps

25 FPS

576 Kbps

15 FPS

307 Kbps

8 FPS

154 Kbps

4 FPS

46 Kbps

1 FPS

799 Kbps

461 Kbps

246 Kbps

123 Kbps

37 Kbps

26 FPS

15 FPS

8 FPS

4 FPS

1 FPS

622 Kbps

27 FPS

346 Kbps

15 FPS

184 Kbps

8 FPS

92 Kbps

4 FPS

28 Kbps

1 FPS

445 Kbps

230 Kbps

123 Kbps

61 Kbps

18 Kbps

29 FPS

15 FPS

8 FPS

4 FPS

1 FPS

223 Kbps

29 FPS

115 Kbps

15 FPS

61 Kbps

8 FPS

31 Kbps

4 FPS

9 Kbps

1 FPS

English _ꢅꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

❖ mpeG4 (vGA)

Frame Rate

30 FPS

15 FPS

8 FPS

3 FPS

1 FPS

Quality

4055 Kbps

2580 Kbps

1290 Kbps

737 Kbps

221 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

22 FPS

14 FPS

7 FPS

4 FPS

1 FPS

3533 Kbps

23 FPS

2304 Kbps

15 FPS

1075 Kbps

7 FPS

614 Kbps

4 FPS

184 Kbps

1 FPS

2949 Kbps

1843 Kbps

860 Kbps

492 Kbps

147 Kbps

24 FPS

15 FPS

7 FPS

4 FPS

1 FPS

2304 Kbps

25 FPS

1382 Kbps

15 FPS

645 Kbps

7 FPS

369 Kbps

4 FPS

111 Kbps

1 FPS

1536 Kbps

922 Kbps

430 Kbps

246 Kbps

74 Kbps

25 FPS

15 FPS

7 FPS

4 FPS

1 FPS

1152 Kbps

25 FPS

691 Kbps

15 FPS

323 Kbps

7 FPS

184 Kbps

4 FPS

55 Kbps

1 FPS

998 Kbps

576 Kbps

269 Kbps

154 Kbps

46 Kbps

26 FPS

15 FPS

7 FPS

4 FPS

1 FPS

799 Kbps

26 FPS

461 Kbps

15 FPS

246 Kbps

8 FPS

123 Kbps

4 FPS

37 Kbps

1 FPS

622 Kbps

346 Kbps

184 Kbps

92 Kbps

28 Kbps

27 FPS

15 FPS

8 FPS

4 FPS

1 FPS

415 Kbps

27 FPS

230 Kbps

15 FPS

123 Kbps

8 FPS

61 Kbps

4 FPS

18 Kbps

1 FPS

ꢅꢄ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ h.264 (vGA)

Frame Rate

30 FPS

15 FPS

8 FPS

3 FPS

1 FPS

Quality

2089 Kbps

1229 Kbps

737 Kbps

369 Kbps

147 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

17 FPS

10 FPS

6 FPS

3 FPS

1 FPS

1659 Kbps

18 FPS

1014 Kbps

11 FPS

553 Kbps

6 FPS

276 Kbps

3 FPS

111 Kbps

1 FPS

1459 Kbps

845 Kbps

538 Kbps

307 Kbps

92 Kbps

19 FPS

11 FPS

7 FPS

4 FPS

1 FPS

1229 Kbps

20 FPS

737 Kbps

12 FPS

430 Kbps

7 FPS

246 Kbps

4 FPS

74 Kbps

1 FPS

1014 Kbps

691 Kbps

323 Kbps

184 Kbps

55 Kbps

22 FPS

15 FPS

7 FPS

4 FPS

1 FPS

883 Kbps

23 FPS

576 Kbps

15 FPS

269 Kbps

7 FPS

154 Kbps

4 FPS

46 Kbps

1 FPS

707 Kbps

461 Kbps

215 Kbps

123 Kbps

37 Kbps

23 FPS

15 FPS

7 FPS

4 FPS

1 FPS

553 Kbps

24 FPS

346 Kbps

15 FPS

161 Kbps

7 FPS

92 Kbps

4 FPS

28 Kbps

1 FPS

384 Kbps

230 Kbps

108 Kbps

61 Kbps

18 Kbps

25 FPS

15 FPS

7 FPS

4 FPS

1 FPS

200 Kbps

26 FPS

115 Kbps

15 FPS

54 Kbps

7 FPS

31 Kbps

4 FPS

9 Kbps

1 FPS

English _ꢅꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

❖ mpeG4 (CIF)

Frame Rate

30 FPS

15 FPS

8 FPS

3 FPS

1 FPS

Quality

1382 Kbps

691 Kbps

369 Kbps

184 Kbps

55 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

30 FPS

15 FPS

8 FPS

4 FPS

1 FPS

1152 Kbps

30 FPS

576 Kbps

15 FPS

307 Kbps

8 FPS

154 Kbps

4 FPS

46 Kbps

1 FPS

922 Kbps

461 Kbps

246 Kbps

123 Kbps

37 Kbps

30 FPS

15 FPS

8 FPS

4 FPS

1 FPS

691 Kbps

30 FPS

346 Kbps

15 FPS

184 Kbps

8 FPS

92 Kbps

4 FPS

28 Kbps

1 FPS

461 Kbps

230 Kbps

123 Kbps

61 Kbps

18 Kbps

30 FPS

15 FPS

8 FPS

4 FPS

1 FPS

346 Kbps

30 FPS

173 Kbps

15 FPS

92 Kbps

8 FPS

46 Kbps

4 FPS

14 Kbps

1 FPS

288 Kbps

144 Kbps

77 Kbps

38 Kbps

12 Kbps

30 FPS

15 FPS

8 FPS

4 FPS

1 FPS

230 Kbps

30 FPS

115 Kbps

15 FPS

61 Kbps

8 FPS

31 Kbps

4 FPS

9 Kbps

1 FPS

173 Kbps

86 Kbps

46 Kbps

23 Kbps

7 Kbps

30 FPS

15 FPS

8 FPS

4 FPS

1 FPS

151 Kbps

30 FPS

76 Kbps

15 FPS

40 Kbps

8 FPS

20 Kbps

4 FPS

6 Kbps

1 FPS

ꢅꢆ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ h.264 (CIF)

Frame Rate

30 FPS

15 FPS

8 FPS

3 FPS

1 FPS

Quality

922 Kbps

461 Kbps

215 Kbps

123 Kbps

37 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

30 FPS

15 FPS

7 FPS

4 FPS

1 FPS

691 Kbps

30 FPS

346 Kbps

15 FPS

184 Kbps

8 FPS

92 Kbps

4 FPS

28 Kbps

1 FPS

576 Kbps

288 Kbps

134 Kbps

77 Kbps

23 Kbps

30 FPS

15 FPS

7 FPS

4 FPS

1 FPS

461 Kbps

30 FPS

230 Kbps

15 FPS

108 Kbps

7 FPS

61 Kbps

4 FPS

18 Kbps

1 FPS

346 Kbps

173 Kbps

81 Kbps

46 Kbps

14 Kbps

30 FPS

15 FPS

7 FPS

4 FPS

1 FPS

288 Kbps

30 FPS

144 Kbps

15 FPS

67 Kbps

7 FPS

38 Kbps

4 FPS

12 Kbps

1 FPS

230 Kbps

115 Kbps

54 Kbps

31 Kbps

9 Kbps

30 FPS

15 FPS

7 FPS

4 FPS

1 FPS

173 Kbps

30 FPS

86 Kbps

15 FPS

40 Kbps

7 FPS

23 Kbps

4 FPS

7 Kbps

1 FPS

115 Kbps

58 Kbps

27 Kbps

15 Kbps

5 Kbps

30 FPS

15 FPS

7 FPS

4 FPS

1 FPS

58 Kbps

30 FPS

29 Kbps

15 FPS

13 Kbps

7 FPS

8 Kbps

4 FPS

2 Kbps

1 FPS

English _ꢅꢇ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

FRAme RATe (pAL)



Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1)

H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),

GOP size(15), Deblock(ON), Proﬁle(Baseline), Entropy coding(CAVLC), Motion

estimation(HPel)

MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),

GOP size(15)

❖ mpeG4 (4CIF)

Frame Rate

25 FPS

13 FPS

6 FPS

3 FPS

1 FPS

Quality

4645 Kbps

2654 Kbps

1327 Kbps

664 Kbps

221 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

21 FPS

12 FPS

6 FPS

3 FPS

1 FPS

4055 Kbps

22 FPS

2212 Kbps

12 FPS

1106 Kbps

6 FPS

553 Kbps

3 FPS

184 Kbps

1 FPS

3391 Kbps

1769 Kbps

885 Kbps

442 Kbps

147 Kbps

23 FPS

12 FPS

6 FPS

3 FPS

1 FPS

2544 Kbps

23 FPS

1327 Kbps

12 FPS

664 Kbps

6 FPS

332 Kbps

3 FPS

111 Kbps

1 FPS

1769 Kbps

885 Kbps

442 Kbps

221 Kbps

74 Kbps

24 FPS

12 FPS

6 FPS

3 FPS

1 FPS

1382 Kbps

25 FPS

664 Kbps

12 FPS

332 Kbps

6 FPS

166 Kbps

3 FPS

55 Kbps

1 FPS

1152 Kbps

553 Kbps

276 Kbps

138 Kbps

46 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

922 Kbps

25 FPS

442 Kbps

12 FPS

221 Kbps

6 FPS

111 Kbps

3 FPS

37 Kbps

1 FPS

691 Kbps

332 Kbps

166 Kbps

83 Kbps

28 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

461 Kbps

25 FPS

221 Kbps

12 FPS

111 Kbps

6 FPS

55 Kbps

3 FPS

18 Kbps

1 FPS

ꢆ0_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ h.264 (4CIF)

Frame Rate

25 FPS

13 FPS

6 FPS

3 FPS

1 FPS

Quality

2359 Kbps

1180 Kbps

737 Kbps

442 Kbps

147 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

16 FPS

8 FPS

5 FPS

3 FPS

1 FPS

1991 Kbps

18 FPS

1106 Kbps

10 FPS

664 Kbps

6 FPS

332 Kbps

3 FPS

111 Kbps

1 FPS

1751 Kbps

1014 Kbps

553 Kbps

276 Kbps

92 Kbps

19 FPS

11 FPS

6 FPS

3 FPS

1 FPS

1475 Kbps

20 FPS

885 Kbps

12 FPS

442 Kbps

6 FPS

221 Kbps

3 FPS

74 Kbps

1 FPS

1161 Kbps

664 Kbps

332 Kbps

166 Kbps

55 Kbps

21 FPS

12 FPS

6 FPS

3 FPS

1 FPS

968 Kbps

21 FPS

553 Kbps

12 FPS

276 Kbps

6 FPS

138 Kbps

3 FPS

46 Kbps

1 FPS

811 Kbps

442 Kbps

221 Kbps

111 Kbps

37 Kbps

22 FPS

12 FPS

6 FPS

3 FPS

1 FPS

608 Kbps

22 FPS

332 Kbps

12 FPS

166 Kbps

6 FPS

83 Kbps

3 FPS

28 Kbps

1 FPS

424 Kbps

221 Kbps

111 Kbps

55 Kbps

18 Kbps

23 FPS

12 FPS

6 FPS

3 FPS

1 FPS

230 Kbps

25 FPS

111 Kbps

12 FPS

55 Kbps

6 FPS

28 Kbps

3 FPS

9 Kbps

1 FPS

English _ꢆ1

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

❖ mpeG4 (vGA)

Frame Rate

25 FPS

13 FPS

6 FPS

3 FPS

1 FPS

Quality

4424 Kbps

2654 Kbps

1327 Kbps

664 Kbps

221 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

20 FPS

12 FPS

6 FPS

3 FPS

1 FPS

3871 Kbps

21 FPS

2212 Kbps

12 FPS

1106 Kbps

6 FPS

553 Kbps

3 FPS

184 Kbps

1 FPS

3097 Kbps

1769 Kbps

885 Kbps

442 Kbps

147 Kbps

21 FPS

12 FPS

6 FPS

3 FPS

1 FPS

2433 Kbps

22 FPS

1327 Kbps

12 FPS

664 Kbps

6 FPS

332 Kbps

3 FPS

111 Kbps

1 FPS

1769 Kbps

885 Kbps

442 Kbps

221 Kbps

74 Kbps

24 FPS

12 FPS

6 FPS

3 FPS

1 FPS

1382 Kbps

25 FPS

664 Kbps

12 FPS

332 Kbps

6 FPS

166 Kbps

3 FPS

55 Kbps

1 FPS

1152 Kbps

553 Kbps

276 Kbps

138 Kbps

46 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

922 Kbps

25 FPS

442 Kbps

12 FPS

221 Kbps

6 FPS

111 Kbps

3 FPS

37 Kbps

1 FPS

691 Kbps

332 Kbps

166 Kbps

83 Kbps

28 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

461 Kbps

25 FPS

221 Kbps

12 FPS

111 Kbps

6 FPS

55 Kbps

3 FPS

18 Kbps

1 FPS

ꢆꢀ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ h.264 (vGA)

Frame Rate

25 FPS

13 FPS

6 FPS

3 FPS

1 FPS

Quality

2507 Kbps

1327 Kbps

737 Kbps

442 Kbps

147 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

17 FPS

9 FPS

5 FPS

3 FPS

1 FPS

1991 Kbps

18 FPS

1217 Kbps

11 FPS

664 Kbps

6 FPS

332 Kbps

3 FPS

111 Kbps

1 FPS

1659 Kbps

1106 Kbps

553 Kbps

276 Kbps

92 Kbps

18 FPS

12 FPS

6 FPS

3 FPS

1 FPS

1401 Kbps

19 FPS

885 Kbps

12 FPS

442 Kbps

6 FPS

221 Kbps

3 FPS

74 Kbps

1 FPS

1106 Kbps

664 Kbps

332 Kbps

166 Kbps

55 Kbps

20 FPS

12 FPS

6 FPS

3 FPS

1 FPS

968 Kbps

21 FPS

553 Kbps

12 FPS

276 Kbps

6 FPS

138 Kbps

3 FPS

46 Kbps

1 FPS

774 Kbps

442 Kbps

221 Kbps

111 Kbps

37 Kbps

21 FPS

12 FPS

6 FPS

3 FPS

1 FPS

608 Kbps

22 FPS

332 Kbps

12 FPS

166 Kbps

6 FPS

83 Kbps

3 FPS

28 Kbps

1 FPS

424 Kbps

221 Kbps

111 Kbps

55 Kbps

18 Kbps

23 FPS

12 FPS

6 FPS

3 FPS

1 FPS

230 Kbps

25 FPS

111 Kbps

12 FPS

55 Kbps

6 FPS

28 Kbps

3 FPS

9 Kbps

1 FPS

English _ꢆꢁ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

❖ mpeG4 (CIF)

Frame Rate

25 FPS

13 FPS

6 FPS

3 FPS

1 FPS

Quality

1382 Kbps

664 Kbps

332 Kbps

166 Kbps

55 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

1152 Kbps

25 FPS

553 Kbps

12 FPS

276 Kbps

6 FPS

138 Kbps

3 FPS

46 Kbps

1 FPS

922 Kbps

442 Kbps

221 Kbps

111 Kbps

37 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

691 Kbps

25 FPS

332 Kbps

12 FPS

166 Kbps

6 FPS

83 Kbps

3 FPS

28 Kbps

1 FPS

461 Kbps

221 Kbps

111 Kbps

55 Kbps

18 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

346 Kbps

25 FPS

166 Kbps

12 FPS

83 Kbps

6 FPS

41 Kbps

3 FPS

14 Kbps

1 FPS

288 Kbps

138 Kbps

69 Kbps

35 Kbps

12 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

230 Kbps

25 FPS

111 Kbps

12 FPS

55 Kbps

6 FPS

28 Kbps

3 FPS

9 Kbps

1 FPS

173 Kbps

83 Kbps

41 Kbps

21 Kbps

7 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

151 Kbps

25 FPS

73 Kbps

12 FPS

36 Kbps

6 FPS

18 Kbps

3 FPS

6 Kbps

1 FPS

ꢆꢂ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ h.264 (CIF)

Frame Rate

25 FPS

13 FPS

6 FPS

3 FPS

1 FPS

Quality

922 Kbps

442 Kbps

221 Kbps

111 Kbps

37 Kbps

LEVEL10

LEVEL9

LEVEL8

LEVEL7

LEVEL6

LEVEL5

LEVEL4

LEVEL3

LEVEL2

LEVEL1

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

691 Kbps

25 FPS

332 Kbps

12 FPS

166 Kbps

6 FPS

83 Kbps

3 FPS

28 Kbps

1 FPS

576 Kbps

276 Kbps

138 Kbps

69 Kbps

23 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

461 Kbps

25 FPS

221 Kbps

12 FPS

111 Kbps

6 FPS

55 Kbps

3 FPS

18 Kbps

1 FPS

346 Kbps

166 Kbps

83 Kbps

41 Kbps

14 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

288 Kbps

25 FPS

138 Kbps

12 FPS

69 Kbps

6 FPS

35 Kbps

3 FPS

12 Kbps

1 FPS

230 Kbps

111 Kbps

55 Kbps

28 Kbps

9 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

173 Kbps

25 FPS

83 Kbps

12 FPS

41 Kbps

6 FPS

21 Kbps

3 FPS

7 Kbps

1 FPS

115 Kbps

55 Kbps

28 Kbps

14 Kbps

5 Kbps

25 FPS

12 FPS

6 FPS

3 FPS

1 FPS

58 Kbps

25 FPS

28 Kbps

12 FPS

14 Kbps

6 FPS

7 Kbps

3 FPS

2 Kbps

1 FPS

English _ꢆꢃ

Download from Www.Somanuals.com. All Manuals Search And Download.

appendix

TRoUBLeShooTING

PROBLEM

SOLUTION



Check to make sure that the camera’s Network settings are appropriate.

Check to make sure that all network cables have been connected

properly.



If connected using DHCP, verify that the camera is able to acquire

dynamic IP addresses without any problem.

I can’t access the camera from a

web browser.

If connected using a DDNS URL, verify that the MAC address has been

properly entered.

If the camera is connected to a router, verify that port forwarding is

properly configured.



Connected Viewers become disconnected upon any change to camera or

network configurations.

Viewer got disconnected during

monitoring.



Check all network connections.

If the camera is connected over an xDSL network, it’ s possible for

Viewer to disconnect under poor network conditions.



When you try to connect to the system using a tab browser, the same

cookie information is shared, resulting in errors when connected.

Therefore, instead of using a tab browser, open a new browser window

to connect to the system.

I cannot connect to the system

using a tab browser of Internet

Explorer 7.0.

The camera connected to the

network is not detected in the IP

installer program.



Turn off the firewall settings on your PC and then search the camera

again.

Check whether two or more cameras are set to a single multicast address

instead of different addresses. If a single address is used for multiple

cameras, the images may overlap.

Images overlap.



If the transmission method is set to multicast, check whether there is a

No image appears.

router that supports multicast in the LAN the camera is connected to.

ꢆꢄ_ appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

SOLUTION



Verify the settings in the following sequence:

No JPEG file is transferred via FTP/

SMTP on occurrence of intelligent

video analysis event of camera

even when the <Intelligent Video

Analysis> is set to <Enable>.

A. NTP must be properly configured.

B. The <Intelligent Video Analysis> should be set to <Enable>.

C. Alarm Video Transmission must be enabled.

D. Check for scheduling conflict.

Can <Set Rules> be configured

even when the <Intelligent Video

Analysis> is set to <Disable>?



Yes, it can be. You can set rules for events despite of the intelligent video

analysis setting.

No signal is found at the Alarm

Output port even when an

intelligent video analysis event is

generated.

Check alarm output port settings.



Check if the memory card is defective.

Cannot record into the SD memory

card.

Check if the write protection tab of the memory card is set to “LOCK”.



Check if the memory card is defective.

SD memory indicator does not

turn on even when the SD memory

card is inserted.

Check if the <SD Card Record> is checked in <Setup> - <Event> -

<Alarm image> menu.



Check if the memory card is inserted in the proper direction. Operation

of memory card that is formatted by other devices is not guaranteed

with this camera unit

SD memory card is inserted but

the camera does not operate

properly.



Format the memory card again in <Setup> - <Event> - <Record

setup> menu.

Cannot format the SD memory

card.

Check if the write protection tab of the memory card is set to "LOCK".

English _ꢆꢅ

Download from Www.Somanuals.com. All Manuals Search And Download.

GpL/LGpL SoFTWARe LICeNSe

This product uses open-source software distributed under the terms of GPL and LGPL.

And you can request by email to [email protected] to get the source codes of the

following GPL and LGPL software used for this product.



GPL S/W

Base Kernel, Busybox, Sysvinit, dosfstools



LGPL S/W

gLibc, Inetutils

want it, that you can change the software

or use pieces of it in new free programs ;

and that you know you can do these things.

GNU GeNeRAL pUBLIC LICeNSe

Version 2, June 1991

Foundation, Inc.

To protect your rights, we need to make

restrictions that forbid anyone to deny you

these rights or to ask you to surrender the

rights. These restrictions translate to certain

responsibilities for you if you distribute

copies of the software, or if you modify it.

51 Franklin Street,Fifth Floor, Boston,

MA 02110-1301, USA

Everyone is permitted to copy and

distribute verbatim copies of this license

document, but changing it is not allowed.

For example, if you distribute copies of

such a program, whether gratis or for a fee,

you must give the recipients all the rights

that you have.

preamble

The licenses for most software are designed

to take away your freedom to share and

change it. By contrast, the GNU General

Public License is intended to guarantee

your freedom to share and change free

software-- to make sure the software is free

for all its users.

You must make sure that they, too, receive or

can get the source code. And you must show

them these terms so they know their rights.

We protect your rights with two steps :

(1)copyright the software, and (2)offer

you this license which gives you legal

permission to copy, distribute and/or

modify the software.

This General Public License applies to most

of the Free Software Foundation's software

and to any other program whose authors

commit to using it. (Some other Free Software

Foundation software is covered by the GNU

Lesser General Public License instead.) You

can apply it to your programs, too.

Also, for each author's protection and ours,

we want to make certain that everyone

understands that there is no warranty for

this free software. If the software is modiﬁed

by someone else and passed on, we want

its recipients to know that what they have

is not the original, so that any problems

introduced by others will not reﬂect on the

original authors' reputations.

When we speak of free software, we are

referring to freedom, not price.

Our General Public Licenses are designed

to make sure that you have the freedom

to distribute copies of free software (and

charge for this service if you wish), that you

receive source code or can get it if you

Finally, any free program is threatened

constantly by software patents. We wish

Download from Www.Somanuals.com. All Manuals Search And Download.

to avoid the danger that redistributors of a

free program will individually obtain patent

licenses, in effect making the program

proprietary. To prevent this, we have made

it clear that any patent must be licensed for

everyone's free use or not licensed at all.

recipients of the Program a copy of this

License along with the Program.

You may charge a fee for the physical

act of transferring a copy, and you may

at your option offer warranty protection

in exchange for a fee.

The precise terms and conditions for

2. You may modify your copy or copies

of the Program or any portion of it,

thus forming a work based on the

Program, and copy and distribute such

modiﬁcations or work under the terms of

Section 1 above, provided that you also

meet all of these conditions :

copying, distribution and modiﬁcation follow.

TeRmS ANd CoNdITIoNS FoR

CopyING, dISTRIBUTIoN ANd

modIFICATIoN

0. This License applies to any program

or other work which contains a notice

placed by the copyright holder saying it

may be distributed under the terms of

this General Public License.

a) You must cause the modiﬁed ﬁles to

carry prominent notices stating that

you changed the ﬁles and the date of

any change.

b) You must cause any work that you

distribute or publish, that in whole or

in part contains or is derived from the

Program or any part thereof, to be

licensed as a whole at no charge to

all third parties under the terms of this

License.

The "Program", below, refers to any such

program or work, and a "work based on

the Program" means either the Program

or any derivative work under copyright

law : that is to say, a work containing the

Program or a portion of it, either verbatim

or with modiﬁcations and/or translated

into another language. (Hereinafter,

translation is included without limitation

in the term "modiﬁcation".) Each licensee

is addressed as "you".

c) If the modiﬁed program normally

reads commands interactively

when run,you must cause it, when

started running for such interactive

use in the most ordinary way, to

print or display an announcement

including an appropriate copyright

notice and a notice that there is no

warranty (or else, saying that you

provide a warranty) and that users

may redistribute the program under

these conditions, and telling the user

how to view a copy of this License.

(Exception:if the Program itself is

interactive but does not normally print

such an announcement, your work

based on the Program is not required

to print an announcement.)

Activities other than copying, distribution

and modiﬁcation are not covered by

this License ; they are outside its scope.

The act of running the Program is not

restricted, and the output from the

Program is covered only if its contents

constitute a work based on the Program

(independent of having been made by

running the Program). Whether that is

true depends on what the Program does.

1. You may copy and distribute verbatim

copies of the Program's source code as

you receive it, in any medium, provided

that you conspicuously and appropriately

publish on each copy an appropriate

These requirements apply to the modiﬁed

work as a whole. If identiﬁable sections

of that work are not derived from

warranty; keep intact all the notices that

refer to this License and to the absence

of any warranty ; and give any other

the Program, and can be reasonably

Download from Www.Somanuals.com. All Manuals Search And Download.

considered independent and separate

works in themselves, then this License, and

its terms, do not apply to those sections

when you distribute them as separate

works. But when you distribute the same

sections as part of a whole which is a work

based on the Program, the distribution

of the whole must be on the terms of this

License, whose permissions for other

licensees extend to the entire whole, and

thus to each and every part regardless of

who wrote it.

c) Accompany it with the information

you received as to the offer to

distribute corresponding source code.

(This alternative is allowed only for

noncommercial distribution and only

if you received the program in object

code or executable form with such

an offer, in accord with Subsection b

above.)

The source code for a work means the

preferred form of the work for making

modiﬁcations to it. For an executable work,

complete source code means all the source

code for all modules it contains, plus any

associated interface deﬁnition ﬁles, plus

the scripts used to control compilation and

installation of the executable. However,

as a special exception, the source code

distributed need not include anything that

is normally distributed (in either source or

binary form)with the major components

(compiler, kernel, and so on)of the operating

system on which the executable runs,

unless that component itself accompanies

the executable.

Thus, it is not the intent of this section to

claim rights or contest your rights to work

written entirely by you ; rather, the intent is to

exercise the right to control the distribution

of derivative or collective works based on

the Program. In addition, mere aggregation

of another work not based on the Program

with the Program (or with a work based on

the Program)on a volume of a storage or

distribution medium does not bring the other

work under the scope of this License.

3. You may copy and distribute the

Program (or a work based on it, under

Section 2)in object code or executable

form under the terms of Sections 1 and

2 above provided that you also do one of

the following :

If distribution of executable or object code

is made by offering access to copy from a

designated place, then offering equivalent

access to copy the source code from the

same place counts as distribution of the

source code, even though third parties are

not compelled to copy the source along

with the object code.

a) Accompany it with the complete

corresponding machine-readable

source code, which must be

distributed under the terms of

Sections 1 and 2 above on a medium

customarily used for software

interchange ; or,

4. You may not copy, modify, sublicense,

or distribute the Program except as

expressly provided under this License.

Any attempt otherwise to copy, modify,

sublicense or distribute the Program is

void, and will automatically terminate

your rights under this License.

b) Accompany it with a written offer,

valid for at least three years, to give

any third party, for a charge no

more than your cost of physically

performing source distribution, a

complete machinereadable copy

of the corresponding source code,

to be distributed under the terms

of Sections 1 and 2 above on a

medium customarily used for software

interchange ; or,

However, parties who have received

copies, or rights, from you under this

License will not have their licenses

terminated so long as such parties

remain in full compliance.

5. You are not required to accept this

License, since you have not signed it.

Download from Www.Somanuals.com. All Manuals Search And Download.

However, nothing else grants you

a whole is intended to apply in other

permission to modify or distribute the

Program or its derivative works.

circumstances. It is not the purpose of

this section to induce you to infringe any

patents or other property right claims or

to contest validity of any such claims; this

section has the sole purpose of protecting

the integrity of the free software distribution

system, which is implemented by public

license practices. Many people have made

generous contributions to the wide range

of software distributed through that system

in reliance on consistent application of that

system ; it is up to the author/donor to

decide if he or she is willing to distribute

software through any other system and a

licensee cannot impose that choice.

These actions are prohibited by law if you

do not accept this License.Therefore, by

modifying or distributing the Program (or

any work based on the Program), you

indicate your acceptance of this License

to do so, and all its terms and conditions

for copying, distributing or modifying the

Program or works based on it.

6. Each time you redistribute the Program

(or any work based on the Program),

the recipient automatically receives a

license from the original licensor to copy,

distribute or modify the Program subject

to these terms and conditions.

This section is intended to make thoroughly

clear what is believed to be a consequence

of the rest of this License.

You may not impose any further

restrictions on the recipients' exercise of

the rights granted herein.

8. If the distribution and/or use of the

Program is restricted in certain countries

either by patents or by copyrighted

interfaces, the original copyright holder

who places the Program under this

License may add an explicit geographical

distribution limitation excluding those

countries,so that distribution is permitted

only in or among countries not thus

excluded. In such case, this License

incorporates the limitation as if written in

the body of this License.

You are not responsible for enforcing

compliance by third parties to this

License.

7. If, as a consequence of a court judgment

or allegation of patent infringement or for

any other reason (not limited to patent

issues), conditions are imposed on you

(whether by court order, agreement or

otherwise)that contradict the conditions

of this License, they do not excuse you

from the conditions of this License. If

you cannot distribute so as to satisfy

simultaneously your obligations under

this License and any other pertinent

obligations, then as a consequence you

may not distribute the Program at all.

For example, if a patent license would

not permit royalty-free redistribution of

the Program by all those who receive

copies directly or indirectly through you,

then the only way you could satisfy both

it and this License would be to refrain

entirely from distribution of the Program.

9. The Free Software Foundation may

publish revised and/or new versions of

the General Public License from time to

time. Such new versions will be similar

in spirit to the present version, but may

differ in detail to address new problems

or concerns.

Each version is given a distinguishing

version number. If the Program speciﬁes

a version number of this License which

applies to it and "any later version", you

have the option of following the terms and

conditions either of that version or of any

later version published by the Free Software

Foundation. If the Program does not specify

a version number of this License, you may

If any portion of this section is held invalid

or unenforceable under any particular

circumstance, the balance of the section

is intended to apply and the section as

Download from Www.Somanuals.com. All Manuals Search And Download.

choose any version ever published by the

Free Software Foundation.

USE OR INABILITY TO USE THE

PROGRAM (INCLUDING BUT NOT

LIMITED TO LOSS OF DATA OR DATA

BEING RENDERED INACCURATE

OR LOSSES SUSTAINED BY YOU

OR THIRD PARTIES OR A FAILURE

OF THE PROGRAM TO OPERATE

WITH ANY OTHER PROGRAMS),

EVEN IF SUCH HOLDER OR OTHER

PARTY HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

10. If you wish to incorporate parts of the

Program into other free programs

whose distribution conditions are

different, write to the author to ask

for permission. For software which

is copyrighted by the Free Software

Foundation,write to the Free Software

Foundation ; we sometimes make

exceptions for this. Our decision will be

guided by the two goals of preserving

the free status of all derivatives of our

free software and of promoting the

sharing and reuse of software generally.

eNd oF TeRmS ANd CoNdITIoNS

how to Apply These Terms to your

New programs

No WARRANTy

If you develop a new program, and you

want it to be of the greatest possible use to

the public, the best way to achieve this is to

make it free software which everyone can

redistribute and change under these terms.

11. BECAUSE THE PROGRAM IS

LICENSED FREE OF CHARGE,

THERE IS NO WARRANTY FOR

THE PROGRAM, TO THE EXTENT

PERMITTED BY APPLICABLE LAW.

EXCEPT WHEN OTHERWISE STATED IN

WRITING THE COPYRIGHT HOLDERS

AND/OR OTHER PARTIES PROVIDE

THE PROGRAM "ASIS" WITHOUT

WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR

PURPOSE. THE ENTIRE RISK AS TO

THE QUALITY AND PERFORMANCE OF

THE PROGRAM IS WITH YOU. SHOULD

THE PROGRAMPROVE DEFECTIVE,

YOU ASSUME THE COST OF ALL

NECESSARY SERVICING, REPAIR OR

CORRECTION.

To do so, attach the following notices to

the program. It is safest to attach them

to the start of each source ﬁle to most

effectively convey the exclusion of warranty

; and each ﬁle should have at least the

"copyright" line and a pointer to where the

full notice is found.

one line to give the program's name and an

idea of what it does.

This program is free software ; you can

redistribute it and/or modify it under the

terms of the GNU General Public License as

published by the Free Software Foundation

; either version 2 of the License, or (at your

option)any later version.

This program is distributed in the hope

that it will be useful, but WITHOUT ANY

WARRANTY ; without even the implied

warranty of MERCHANTABILITY or

FITNESS FOR A PARTICULAR PURPOSE.

See the GNU General Public License for

more details.

12. IN NO EVENT UNLESS REQUIRED

BY APPLICABLE LAW OR AGREED

TO IN WRITING WILL ANY

OTHER PARTY WHO MAY MODIFY

AND/OR REDISTRIBUTE DAMAGES,

INCLUDING ANY GENERAL, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE

Download from Www.Somanuals.com. All Manuals Search And Download.

You should have received a copy of the

GNU General Public License along with this

program ; if not, write to the Free Software

Foundation, Inc.,51 Franklin Street, Fifth

Floor, Boston, MA 02110-1301, USA.

GNU GeNeRAL pUBLIC LICeNSe

Version 3, 29 June 2007

Inc. <http://fsf.org/>

Also add information on how to contact you

by electronic and paper mail. If the program

is interactive, make it output a short notice

like this when it starts in an interactive

mode :

Everyone is permitted to copy and distribute

verbatim copies of this license document, but

changing it is not allowed.

preamble

Gnomovision version 69,

The GNU General Public License is a free,

copyleft license for software and other kinds

of works.

Gnomovision comes with ABSOLUTELY

The licenses for most software and other

practical works are designed to take away

your freedom to share and change the works.

By contrast, the GNU General Public License

is intended to guarantee your freedom to

share and change all versions of a program--

to make sure it remains free software for all its

users. We, the Free Software Foundation, use

the GNU General Public License for most of

our software; it applies also to any other work

released this way by its authors. You can

apply it to your programs, too.

WARRANTY ; for details type ‘show w’.

This is free software, and you are welcome

to redistribute it under certain conditions ;

type ‘show c’ for details.

The hypothetical commands ‘show w’ and

‘show c’ should show the appropriate parts

of the General Public License. Of course,

the commands you use may be called

something other than ‘show w’ and ‘show

c’ ; they could even be mouse-clicks or

menu items-- whatever suits your program.

When we speak of free software, we are

referring to freedom, not price. Our General

Public Licenses are designed to make sure

that you have the freedom to distribute copies

of free software (and charge for them if you

wish), that you receive source code or can

get it if you want it, that you can change

the software or use pieces of it in new free

programs, and that you know you can do

these things.

You should also get your employer (if you

work as a programmer)or your school, if

any, to sign a "copyright disclaimer" for the

program,if necessary. Here is a sample ;

alter the names:

Yoyodyne, Inc.,hereby disclaims all

Gnomovision’ (which makes passes at

compilers) written by James Hacker.

To protect your rights, we need to prevent

others from denying you these rights or asking

you to surrender the rights. Therefore, you

have certain responsibilities if you distribute

copies of the software, or if you modify it:

responsibilities to respect the freedom of

others.

signature of Ty Coon, 1 April 1989 Ty

Coon, President of Vice This General Public

License does not permit incorporating your

program into proprietary programs. If your

program is a subroutine library, you may

consider it more useful to permit linking

proprietary applications with the library. If

this is what you want to do, use the GNU

Lesser General public License instead of

this License.

For example, if you distribute copies of such a

program, whether gratis or for a fee, you must

pass on to the recipients the same freedoms

that you received. You must make sure that

they, too, receive or can get the source code.

Download from Www.Somanuals.com. All Manuals Search And Download.

And you must show them these terms so they

know their rights.

TeRmS ANd CoNdITIoNS

0. deﬁnitions.

Developers that use the GNU GPL protect

your rights with two steps: (1) assert copyright

on the software, and (2) offer you this License

giving you legal permission to copy, distribute

and/or modify it.

“This License” refers to version 3 of the GNU

General Public License.

“Copyright” also means copyright-like laws

that apply to other kinds of works, such as

semiconductor masks.

For the developers' and authors' protection,

the GPL clearly explains that there is no

warranty for this free software. For both users'

and authors' sake, the GPL requires that

modiﬁed versions be marked as changed,

so that their problems will not be attributed

erroneously to authors of previous versions.

“The Program” refers to any copyrightable

work licensed under this License. Each

licensee is addressed as “you”. “Licensees”

and “recipients” may be individuals or

organizations.

To “modify” a work means to copy from

or adapt all or part of the work in a fashion

requiring copyright permission, other than the

making of an exact copy. The resulting work

is called a “modiﬁed version” of the earlier

work or a work “based on” the earlier work.

Some devices are designed to deny users

access to install or run modiﬁed versions

of the software inside them, although the

manufacturer can do so. This is fundamentally

incompatible with the aim of protecting

users' freedom to change the software. The

systematic pattern of such abuse occurs

in the area of products for individuals to

use, which is precisely where it is most

unacceptable. Therefore, we have designed

this version of the GPL to prohibit the practice

for those products. If such problems arise

substantially in other domains, we stand ready

to extend this provision to those domains

in future versions of the GPL, as needed to

protect the freedom of users.

A “covered work” means either the unmodiﬁed

Program or a work based on the Program.

To “propagate” a work means to do anything

with it that, without permission, would

make you directly or secondarily liable for

infringement under applicable copyright

law, except executing it on a computer

or modifying a private copy. Propagation

includes copying, distribution (with or without

modiﬁcation), making available to the public,

and in some countries other activities as well.

Finally, every program is threatened constantly

by software patents. States should not allow

patents to restrict development and use of

software on general-purpose computers,

but in those that do, we wish to avoid the

special danger that patents applied to a free

program could make it effectively proprietary.

To prevent this, the GPL assures that patents

cannot be used to render the program non-

free.

To “convey” a work means any kind of

propagation that enables other parties to

make or receive copies. Mere interaction with

a user through a computer network, with no

transfer of a copy, is not conveying.

An interactive user interface displays

“Appropriate Legal Notices” to the extent

that it includes a convenient and prominently

visible feature that (1) displays an appropriate

there is no warranty for the work (except

to the extent that warranties are provided),

that licensees may convey the work under

this License, and how to view a copy of this

License.

The precise terms and conditions for copying,

distribution and modiﬁcation follow.

If the interface presents a list of user

commands or options, such as a menu, a

prominent item in the list meets this criterion.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Source Code.

The Corresponding Source need not

include anything that users can regenerate

automatically from other parts of the

Corresponding Source.

The “source code” for a work means the

preferred form of the work for making

modiﬁcations to it. “Object code” means any

non-source form of a work.

The Corresponding Source for a work in

source code form is that same work.

A “Standard Interface” means an interface

that either is an ofﬁcial standard deﬁned

by a recognized standards body, or, in the

case of interfaces speciﬁed for a particular

programming language, one that is widely

used among developers working in that

language.

2. Basic permissions.

All rights granted under this License are

granted for the term of copyright on the

Program, and are irrevocable provided the

stated conditions are met. This License

explicitly afﬁrms your unlimited permission to

run the unmodiﬁed Program. The output from

running a covered work is covered by this

License only if the output, given its content,

constitutes a covered work. This License

acknowledges your rights of fair use or other

equivalent, as provided by copyright law.

The “System Libraries” of an executable

work include anything, other than the work

as a whole, that (a) is included in the normal

form of packaging a Major Component, but

which is not part of that Major Component,

and (b) serves only to enable use of the

work with that Major Component, or to

implement a Standard Interface for which

an implementation is available to the public

in source code form. A “Major Component”,

in this context, means a major essential

component (kernel, window system, and so

on) of the speciﬁc operating system (if any) on

which the executable work runs, or a compiler

used to produce the work, or an object code

interpreter used to run it.

You may make, run and propagate covered

works that you do not convey, without

conditions so long as your license otherwise

remains in force. You may convey covered

works to others for the sole purpose of having

them make modiﬁcations exclusively for you,

or provide you with facilities for running those

works, provided that you comply with the

terms of this License in conveying all material

for which you do not control copyright. Those

thus making or running the covered works for

you must do so exclusively on your behalf,

under your direction and control, on terms

that prohibit them from making any copies

of your copyrighted material outside their

relationship with you.

The “Corresponding Source” for a work

in object code form means all the source

code needed to generate, install, and (for

an executable work) run the object code

and to modify the work, including scripts

to control those activities. However, it does

not include the work's System Libraries, or

general-purpose tools or generally available

free programs which are used unmodiﬁed in

performing those activities but which are not

part of the work. For example, Corresponding

Source includes interface deﬁnition ﬁles

associated with source ﬁles for the work,

and the source code for shared libraries and

dynamically linked subprograms that the work

is speciﬁcally designed to require, such as by

intimate data communication or control ﬂow

between those subprograms and other parts

of the work.

Conveying under any other circumstances is

permitted solely under the conditions stated

below. Sublicensing is not allowed; section 10

makes it unnecessary.

3. protecting Users' Legal Rights From

Anti-Circumvention Law.

No covered work shall be deemed part of an

effective technological measure under any

applicable law fulﬁlling obligations under article

11 of the WIPO copyright treaty adopted on

20 December 1996, or similar laws prohibiting

or restricting circumvention of such measures.

Download from Www.Somanuals.com. All Manuals Search And Download.

When you convey a covered work, you waive

any legal power to forbid circumvention of

technological measures to the extent such

circumvention is effected by exercising rights

under this License with respect to the covered

work, and you disclaim any intention to limit

operation or modiﬁcation of the work as a

means of enforcing, against the work's users,

your or third parties' legal rights to forbid

circumvention of technological measures.

This License gives no permission to

license the work in any other way, but it

does not invalidate such permission if you

have separately received it.

. d) If the work has interactive user interfaces,

each must display Appropriate Legal

Notices; however, if the Program has

interactive interfaces that do not display

Appropriate Legal Notices, your work

need not make them do so.

4. Conveying verbatim Copies.

A compilation of a covered work with other

separate and independent works, which are

not by their nature extensions of the covered

work, and which are not combined with it

such as to form a larger program, in or on a

volume of a storage or distribution medium, is

called an “aggregate” if the compilation and

its resulting copyright are not used to limit

the access or legal rights of the compilation's

users beyond what the individual works

permit. Inclusion of a covered work in an

aggregate does not cause this License to

apply to the other parts of the aggregate.

You may convey verbatim copies of the

Program's source code as you receive it, in

any medium, provided that you conspicuously

and appropriately publish on each copy an

appropriate copyright notice; keep intact

all notices stating that this License and any

non-permissive terms added in accord with

section 7 apply to the code; keep intact all

notices of the absence of any warranty; and

give all recipients a copy of this License along

with the Program.

You may charge any price or no price for

each copy that you convey, and you may offer

support or warranty protection for a fee.

6. Conveying Non-Source Forms.

You may convey a covered work in object

code form under the terms of sections 4 and 5,

provided that you also convey the machine-

readable Corresponding Source under the

terms of this License, in one of these ways:

5. Conveying modiﬁed Source versions.

You may convey a work based on the

Program, or the modiﬁcations to produce it

from the Program, in the form of source code

under the terms of section 4, provided that

you also meet all of these conditions:

. a) Convey the object code in, or embodied

in, a physical product (including a physical

distribution medium), accompanied by the

Corresponding Source ﬁxed on a durable

physical medium customarily used for

software interchange.

. a) The work must carry prominent notices

stating that you modiﬁed it, and giving a

relevant date.

. b) The work must carry prominent notices

stating that it is released under this

License and any conditions added under

section 7. This requirement modiﬁes the

requirement in section 4 to “keep intact

all notices”.

. b) Convey the object code in, or embodied

in, a physical product (including a physical

distribution medium), accompanied by

a written offer, valid for at least three

years and valid for as long as you offer

spare parts or customer support for

that product model, to give anyone who

possesses the object code either (1) a

copy of the Corresponding Source for all

the software in the product that is covered

by this License, on a durable physical

medium customarily used for software

interchange, for a price no more than your

. c) You must license the entire work, as a

whole, under this License to anyone who

comes into possession of a copy. This

License will therefore apply, along with

any applicable section 7 additional terms,

to the whole of the work, and all its parts,

regardless of how they are packaged.

Download from Www.Somanuals.com. All Manuals Search And Download.

reasonable cost of physically performing

this conveying of source, or (2) access to

copy the Corresponding Source from a

network server at no charge.

resolved in favor of coverage. For a particular

product received by a particular user,

“normally used” refers to a typical or common

use of that class of product, regardless of

the status of the particular user or of the way

in which the particular user actually uses, or

expects or is expected to use, the product.

A product is a consumer product regardless

of whether the product has substantial

commercial, industrial or non-consumer uses,

unless such uses represent the only signiﬁcant

mode of use of the product.

. c) Convey individual copies of the object

code with a copy of the written offer to

provide the Corresponding Source. This

alternative is allowed only occasionally

and noncommercially, and only if you

received the object code with such an

offer, in accord with subsection 6b.

. d) Convey the object code by offering

access from a designated place (gratis or

for a charge), and offer equivalent access

to the Corresponding Source in the same

way through the same place at no further

charge. You need not require recipients

to copy the Corresponding Source along

with the object code. If the place to copy

the object code is a network server,

the Corresponding Source may be on

a different server (operated by you or

a third party) that supports equivalent

copying facilities, provided you maintain

clear directions next to the object code

saying where to ﬁnd the Corresponding

Source. Regardless of what server hosts

the Corresponding Source, you remain

obligated to ensure that it is available

for as long as needed to satisfy these

requirements.

“Installation Information” for a User

Product means any methods, procedures,

authorization keys, or other information

required to install and execute modiﬁed

versions of a covered work in that User

Product from a modiﬁed version of its

Corresponding Source. The information

must sufﬁce to ensure that the continued

functioning of the modiﬁed object code is in

no case prevented or interfered with solely

because modiﬁcation has been made.

If you convey an object code work under this

section in, or with, or speciﬁcally for use in,

a User Product, and the conveying occurs

as part of a transaction in which the right of

possession and use of the User Product is

transferred to the recipient in perpetuity or for

a ﬁxed term (regardless of how the transaction

is characterized), the Corresponding Source

conveyed under this section must be

. e) Convey the object code using peer-to-

peer transmission, provided you inform

other peers where the object code and

Corresponding Source of the work are

being offered to the general public at no

charge under subsection 6d.

accompanied by the Installation Information.

But this requirement does not apply if neither

you nor any third party retains the ability

to install modiﬁed object code on the User

Product (for example, the work has been

installed in ROM).

A separable portion of the object code,

whose source code is excluded from the

Corresponding Source as a System Library,

need not be included in conveying the object

code work.

The requirement to provide Installation

Information does not include a requirement to

continue to provide support service, warranty,

or updates for a work that has been modiﬁed

or installed by the recipient, or for the User

Product in which it has been modiﬁed or

installed. Access to a network may be

A “User Product” is either (1) a “consumer

product”, which means any tangible personal

property which is normally used for personal,

family, or household purposes, or (2) anything

designed or sold for incorporation into a

dwelling. In determining whether a product is

a consumer product, doubtful cases shall be

denied when the modiﬁcation itself materially

and adversely affects the operation of the

network or violates the rules and protocols for

communication across the network.

Download from Www.Somanuals.com. All Manuals Search And Download.

Corresponding Source conveyed, and

Installation Information provided, in accord

with this section must be in a format

that is publicly documented (and with an

implementation available to the public in

source code form), and must require no

special password or key for unpacking,

reading or copying.

reasonable ways as different from the

original version; or

. d) Limiting the use for publicity purposes

of names of licensors or authors of the

material; or

. e) Declining to grant rights under trademark

law for use of some trade names,

trademarks, or service marks; or

7. Additional Terms.

. f) Requiring indemniﬁcation of licensors and

authors of that material by anyone who

conveys the material (or modiﬁed versions

of it) with contractual assumptions of

liability to the recipient, for any liability that

these contractual assumptions directly

impose on those licensors and authors.

“Additional permissions” are terms that

supplement the terms of this License by

making exceptions from one or more of its

conditions. Additional permissions that are

applicable to the entire Program shall be

treated as though they were included in this

License, to the extent that they are valid under

applicable law. If additional permissions apply

only to part of the Program, that part may be

used separately under those permissions,

but the entire Program remains governed by

this License without regard to the additional

permissions.

All other non-permissive additional terms

are considered “further restrictions” within

the meaning of section 10. If the Program

as you received it, or any part of it, contains

a notice stating that it is governed by this

License along with a term that is a further

restriction, you may remove that term. If a

license document contains a further restriction

but permits relicensing or conveying under

this License, you may add to a covered work

material governed by the terms of that license

document, provided that the further restriction

does not survive such relicensing or conveying.

When you convey a copy of a covered work,

you may at your option remove any additional

permissions from that copy, or from any part

of it. (Additional permissions may be written

to require their own removal in certain cases

when you modify the work.) You may place

additional permissions on material, added by

you to a covered work, for which you have or

can give appropriate copyright permission.

If you add terms to a covered work in accord

with this section, you must place, in the

relevant source ﬁles, a statement of the

additional terms that apply to those ﬁles, or a

notice indicating where to ﬁnd the applicable

terms.

Notwithstanding any other provision of this

License, for material you add to a covered

work, you may (if authorized by the copyright

holders of that material) supplement the terms

of this License with terms:

Additional terms, permissive or non-

permissive, may be stated in the form of

a separately written license, or stated as

exceptions; the above requirements apply

either way.

. a) Disclaiming warranty or limiting liability

differently from the terms of sections 15

and 16 of this License; or

. b) Requiring preservation of speciﬁed

reasonable legal notices or author

attributions in that material or in the

Appropriate Legal Notices displayed by

works containing it; or

8. Termination.

You may not propagate or modify a covered

work except as expressly provided under this

License. Any attempt otherwise to propagate

or modify it is void, and will automatically

terminate your rights under this License

(including any patent licenses granted under

the third paragraph of section 11).

. c) Prohibiting misrepresentation of the origin

of that material, or requiring that modiﬁed

versions of such material be marked in

Download from Www.Somanuals.com. All Manuals Search And Download.

However, if you cease all violation of this

License, then your license from a particular

unless and until the copyright holder explicitly

and ﬁnally terminates your license, and (b)

permanently, if the copyright holder fails to

notify you of the violation by some reasonable

means prior to 60 days after the cessation.

An “entity transaction” is a transaction

transferring control of an organization, or

substantially all assets of one, or subdividing

an organization, or merging organizations.

If propagation of a covered work results

from an entity transaction, each party to that

transaction who receives a copy of the work

also receives whatever licenses to the work

the party's predecessor in interest had or

could give under the previous paragraph, plus

a right to possession of the Corresponding

Source of the work from the predecessor in

interest, if the predecessor has it or can get it

with reasonable efforts.

Moreover, your license from a particular

if the copyright holder notiﬁes you of the

violation by some reasonable means, this

is the ﬁrst time you have received notice of

violation of this License (for any work) from

that copyright holder, and you cure the

violation prior to 30 days after your receipt of

the notice.

You may not impose any further restrictions on

the exercise of the rights granted or afﬁrmed

under this License. For example, you may not

impose a license fee, royalty, or other charge

for exercise of rights granted under this License,

and you may not initiate litigation (including a

cross-claim or counterclaim in a lawsuit) alleging

that any patent claim is infringed by making,

using, selling, offering for sale, or importing the

Program or any portion of it.

Termination of your rights under this section

does not terminate the licenses of parties

who have received copies or rights from you

under this License. If your rights have been

terminated and not permanently reinstated,

you do not qualify to receive new licenses for

the same material under section 10.

11. patents.

9. Acceptance Not Required for having

Copies.

A “contributor” is a copyright holder who

authorizes use under this License of the

Program or a work on which the Program is

based. The work thus licensed is called the

contributor's “contributor version”.

You are not required to accept this License

in order to receive or run a copy of the

Program. Ancillary propagation of a covered

work occurring solely as a consequence of

using peer-to-peer transmission to receive a

copy likewise does not require acceptance.

However, nothing other than this License

grants you permission to propagate or modify

any covered work. These actions infringe

Therefore, by modifying or propagating a

covered work, you indicate your acceptance

of this License to do so.

A contributor's “essential patent claims” are

all patent claims owned or controlled by the

contributor, whether already acquired or

hereafter acquired, that would be infringed by

some manner, permitted by this License, of

making, using, or selling its contributor version,

but do not include claims that would be infringed

only as a consequence of further modiﬁcation

of the contributor version. For purposes of this

deﬁnition, “control” includes the right to grant

patent sublicenses in a manner consistent with

the requirements of this License.

10. Automatic Licensing of downstream

Recipients.

Each time you convey a covered work, the

recipient automatically receives a license

from the original licensors, to run, modify

and propagate that work, subject to this

License. You are not responsible for enforcing

compliance by third parties with this License.

Each contributor grants you a non-exclusive,

worldwide, royalty-free patent license under

the contributor's essential patent claims, to

make, use, sell, offer for sale, import and

otherwise run, modify and propagate the

contents of its contributor version.

Download from Www.Somanuals.com. All Manuals Search And Download.

In the following three paragraphs, a “patent

license” is any express agreement or

software, under which you make payment to

the third party based on the extent of your

activity of conveying the work, and under

which the third party grants, to any of the

parties who would receive the covered work

from you, a discriminatory patent license (a) in

connection with copies of the covered work

conveyed by you (or copies made from those

copies), or (b) primarily for and in connection

with speciﬁc products or compilations that

contain the covered work, unless you entered

into that arrangement, or that patent license

was granted, prior to 28 March 2007.

commitment, however denominated, not

to enforce a patent (such as an express

permission to practice a patent or covenant

not to sue for patent infringement). To “grant”

such a patent license to a party means to

make such an agreement or commitment not

to enforce a patent against the party.

If you convey a covered work, knowingly

relying on a patent license, and the

Corresponding Source of the work is not

available for anyone to copy, free of charge

and under the terms of this License, through

a publicly available network server or other

readily accessible means, then you must

either (1) cause the Corresponding Source

to be so available, or (2) arrange to deprive

yourself of the beneﬁt of the patent license

for this particular work, or (3) arrange, in a

manner consistent with the requirements of

this License, to extend the patent license to

downstream recipients. “Knowingly relying”

means you have actual knowledge that, but

for the patent license, your conveying the

covered work in a country, or your recipient's

use of the covered work in a country, would

infringe one or more identiﬁable patents in that

country that you have reason to believe are

Nothing in this License shall be construed

as excluding or limiting any implied license

or other defenses to infringement that may

otherwise be available to you under applicable

patent law.

12. No Surrender of others' Freedom.

If conditions are imposed on you (whether

by court order, agreement or otherwise) that

contradict the conditions of this License, they

do not excuse you from the conditions of

this License. If you cannot convey a covered

work so as to satisfy simultaneously your

obligations under this License and any other

pertinent obligations, then as a consequence

you may not convey it at all. For example, if

you agree to terms that obligate you to collect

a royalty for further conveying from those

to whom you convey the Program, the only

way you could satisfy both those terms and

this License would be to refrain entirely from

conveying the Program.

valid.

If, pursuant to or in connection with a single

transaction or arrangement, you convey, or

propagate by procuring conveyance of, a

covered work, and grant a patent license to

some of the parties receiving the covered

work authorizing them to use, propagate,

modify or convey a speciﬁc copy of the

covered work, then the patent license you

grant is automatically extended to all

recipients of the covered work and works

based on it.

13. Use with the GNU Affero General

public License.

Notwithstanding any other provision of

this License, you have permission to link

or combine any covered work with a work

licensed under version 3 of the GNU Affero

General Public License into a single combined

work, and to convey the resulting work.

The terms of this License will continue to

apply to the part which is the covered work,

but the special requirements of the GNU

Affero General Public License, section 13,

concerning interaction through a network will

apply to the combination as such.

A patent license is “discriminatory” if it does

not include within the scope of its coverage,

prohibits the exercise of, or is conditioned

on the non-exercise of one or more of the

rights that are speciﬁcally granted under this

License. You may not convey a covered work

if you are a party to an arrangement with a

third party that is in the business of distributing

Download from Www.Somanuals.com. All Manuals Search And Download.

14. Revised versions of this License.

16. Limitation of Liability.

The Free Software Foundation may publish

revised and/or new versions of the GNU

General Public License from time to time.

Such new versions will be similar in spirit to

the present version, but may differ in detail to

address new problems or concerns.

IN NO EVENT UNLESS REQUIRED BY

APPLICABLE LAW OR AGREED TO IN

WRITING WILL ANY COPYRIGHT HOLDER,

OR ANY OTHER PARTY WHO MODIFIES

AND/OR CONVEYS THE PROGRAM

AS PERMITTED ABOVE, BE LIABLE TO

YOU FOR DAMAGES, INCLUDING ANY

GENERAL, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARISING OUT

OF THE USE OR INABILITY TO USE THE

PROGRAM (INCLUDING BUT NOT LIMITED

TO LOSS OF DATA OR DATA BEING

RENDERED INACCURATE OR LOSSES

SUSTAINED BY YOU OR THIRD PARTIES

OR A FAILURE OF THE PROGRAM TO

OPERATE WITH ANY OTHER PROGRAMS),

EVEN IF SUCH HOLDER OR OTHER PARTY

HAS BEEN ADVISED OF THE POSSIBILITY

OF SUCH DAMAGES.

Each version is given a distinguishing version

number. If the Program speciﬁes that a certain

numbered version of the GNU General Public

License “or any later version” applies to it, you

have the option of following the terms and

conditions either of that numbered version

or of any later version published by the Free

Software Foundation. If the Program does

not specify a version number of the GNU

General Public License, you may choose any

version ever published by the Free Software

Foundation.

If the Program speciﬁes that a proxy can

decide which future versions of the GNU

General Public License can be used, that

proxy's public statement of acceptance of a

version permanently authorizes you to choose

that version for the Program.

17. Interpretation of Sections 15 and 16.

If the disclaimer of warranty and limitation of

liability provided above cannot be given local

legal effect according to their terms, reviewing

courts shall apply local law that most closely

approximates an absolute waiver of all civil

liability in connection with the Program, unless a

warranty or assumption of liability accompanies

a copy of the Program in return for a fee.

Later license versions may give you additional

or different permissions. However, no

additional obligations are imposed on any

author or copyright holder as a result of your

choosing to follow a later version.

END OF TERMS AND CONDITIONS

15. disclaimer of Warranty.

GNU LeSSeR GeNeRAL pUBLIC

THERE IS NO WARRANTY FOR THE

PROGRAM, TO THE EXTENT PERMITTED

BY APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING THE

PARTIES PROVIDE THE PROGRAM

LICeNSe

Version 2.1, February 1999

Foundation, Inc.

“AS IS” WITHOUT WARRANTY OF

51 Franklin Street, Fifth Floor, Boston,

MA 02110-1301 USA

ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF

Everyone is permitted to copy and

MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. THE ENTIRE RISK

AS TO THE QUALITY AND PERFORMANCE

OF THE PROGRAM IS WITH YOU. SHOULD

THE PROGRAM PROVE DEFECTIVE, YOU

ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

distribute verbatim copies of this license

document, but changing it is not allowed.

[This is the ﬁrst released version of the

Lesser GPL. It also counts as the successor

of the GNU Library Public License, version

2, hence the version number 2.1.]

Download from Www.Somanuals.com. All Manuals Search And Download.

We protect your rights with a two-step

method : (1)we copyright the library, and

(2)we offer you this license, which gives you

legal permission to copy, distribute and/or

modify the library.

preamble

The licenses for most software are designed

to take away your freedom to share and

change it. By contrast, the GNU General

Public Licenses are intended to guarantee

your freedom to share and change free

software--to make sure the software is free

for all its users.

To protect each distributor, we want to

make it very clear that there is no warranty

for the free library. Also, if the library is

modiﬁed by someone else and passed

on, the recipients should know that what

they have is not the original version,so

that the original author's reputation will

not be affected by problems that might be

introduced by others.

This license, the Lesser General Public

License, applies to some specially

designated software packages--typically

libraries--of the Free Software Foundation

and other authors who decide to use it.You

can use it too, but we suggest you ﬁrst

think carefully about whether this license or

the ordinary General Public License is the

better strategy to use in any particular case,

based on the explanations below.

Finally, software patents pose a constant

threat to the existence of any free program.

We wish to make sure that a company

cannot effectively restrict the users of a free

program by obtaining a restrictive license

from a patent holder.

When we speak of free software, we are

referring to freedom of use, not price.

Our General Public Licenses are designed

to make sure that you have the freedom

to distribute copies of free software (and

charge for this service if you wish) ; that

you receive source code or can get it if you

want it ; that you can change the software

and use pieces of it in new free programs ;

and that you are informed that you can do

these things.

Therefore, we insist that any patent license

obtained for a version of the library must

be consistent with the full freedom of use

speciﬁed in this license.

Most GNU software, including some

libraries, is covered by the ordinary GNU

General Public License. This license, the

GNU Lesser General Public License,

applies to certain designated libraries, and

is quite different from the ordinary General

Public License. We use this license for

certain libraries in order to permit linking

those libraries into non-free programs.

To protect your rights, we need to make

restrictions that forbid distributors to deny

you these rights or to ask you to surrender

these rights. These restrictions translate to

certain responsibilities for you if you distribute

copies of the library or if you modify it.

When a program is linked with a library,

whether statically or using a shared library,

the combination of the two is legally

speaking a combined work, a derivative of

the original library. The ordinary General

Public License therefore permits such

linking only if the entire combination ﬁts its

criteria of freedom.

For example, if you distribute copies of the

library, whether gratis or for a fee, you must

give the recipients all the rights that we

gave you. You must make sure that they,

too, receive or can get the source code.

If you link other code with the library, you

must provide complete object ﬁles to the

recipients, so that they can relink them with

the library after making changes to the library

and recompiling it. And you must show them

these terms so they know their rights.

The Lesser General Public License permits

more lax criteria for linking other code with

the library.

Download from Www.Somanuals.com. All Manuals Search And Download.

We call this license the "Lesser" General

Public License because it does Less

to protect the user's freedom than the

ordinary General Public License. It also

provides other free software developers

Less of an advantage over competing non-

free programs.

TeRmS ANd CoNdITIoNS FoR

CopyING, dISTRIBUTIoN ANd

modIFICATIoN

0. This License Agreement applies to any

software library or other program which

contains a notice placed by the copyright

holder or other authorized party saying

it may be distributed under the terms of

this Lesser General Public License (also

called "this License"). Each licensee is

addressed as "you".

These disadvantages are the reason we

use the ordinary General Public License for

many libraries. However, the Lesser license

provides advantages in certain special

circumstances.

A "library" means a collection of software

functions and/or data prepared so as to

be conveniently linked with application

programs (which use some of those

functions and data)to form executables.

For example, on rare occasions, there may

be a special need to encourage the widest

possible use of a certain library, so that it

becomes a de-facto standard. To achieve

this, non-free programs must be allowed to

use the library. A more frequent case is that

a free library does the same job as widely

used non-free libraries. In this case, there

is little to gain by limiting the free library to

free software only, so we use the Lesser

General Public License.

The "Library", below, refers to any such

software library or work which has been

distributed under these terms. A "work

based on the Library" means either the

Library or any derivative work under

containing the Library or a portion of

it,either verbatim or with modiﬁcations

and/or translated straightforwardly into

another language. (Hereinafter, translation

is included without limitation in the term

"modiﬁcation".)

In other cases,permission to use a

particular library in non-free programs

enables a greater number of people to use

a large body of free software. For example,

permission to use the GNU C Library in

non-free programs enables many more

people to use the whole GNU operating

system, as well as its variant, the GNU/

Linux operating system.

"Source code" for a work means the

preferred form of the work for making

modiﬁcations to it.

Although the Lesser General Public License

is Less protective of the users' freedom, it

does ensure that the user of a program that

is linked with the Library has the freedom

and the wherewithal to run that program

using a modiﬁed version of the Library.

For a library, complete source code

means all the source code for all modules

it contains, plus any associated interface

deﬁnition ﬁles, plus the scripts used to

control compilation and installation of the

library.

The precise terms and conditions for

copying, distribution and modiﬁcation

follow. Pay close attention to the difference

between a "work based on the library" and

a "work that uses the library". The former

contains code derived from the library,

whereas the latter must be combined with

the library in order to run.

Activities other than copying, distribution

and modiﬁcation are not covered by this

License ; they are outside its scope. The act

of running a program using the Library is not

restricted, and output from such a program

is covered only if its contents constitute a

work based on the Library (independent of

the use of the Library in a tool for writing it).

Download from Www.Somanuals.com. All Manuals Search And Download.

Whether that is true depends on what the

Library does and what the program that

uses the Library does.

(For example, a function in a library to

compute square roots has a purpose

that is entirely well-deﬁned independent

of the application. Therefore,Subsection

2d requires that any application-supplied

function or table used by this function must

be optional : if the application does not

supply it, the square root function must still

compute square roots.)

1. You may copy and distribute verbatim

copies of the Library's complete source

code as you receive it, in any medium,

provided that you conspicuously and

appropriately publish on each copy

an appropriate copyright notice and

disclaimer of warranty ; keep intact all

the notices that refer to this License and

to the absence of any warranty ; and

distribute a copy of this License along

with the Library.

These requirements apply to the modiﬁed

work as a whole. If identiﬁable sections of that

work are not derived from the Library, and

can be reasonably considered independent

and separate works in themselves, then this

License, and its terms, do not apply to those

sections when you distribute them as separate

works. But when you distribute the same

sections as part of a whole which is a work

based on the Library, the distribution of the

whole must be on the terms of this License,

whose permissions for other licensees extend

to the entire whole, and thus to each and

every part regardless of who wrote it. Thus, it

is not the intent of this section to claim rights

or contest your rights to work written entirely

by you ; rather, the intent is to exercise the

right to control the distribution of derivative or

collective works based on the Library.

You may charge a fee for the physical act

of transferring a copy, and you may at

your option offer warranty protection in

exchange for a fee.

2. You may modify your copy or copies

of the Library or any portion of it, thus

forming a work based on the Library, and

copy and distribute such modiﬁcations

or work under the terms of Section 1

above, provided that you also meet all of

these conditions :

ꢀ

a)The modiﬁed work must itself be a

software library.

ꢀ

b)You must cause the ﬁles modiﬁed to

In addition, mere aggregation of another

work not based on the Library with the

Library (or with a work based on the

Library)on a volume of a storage or

carry prominent notices stating that

you changed the ﬁles and the date of

any change.

distribution medium does not bring the

other work under the scope of this License.

ꢀ

c)You must cause the whole of the work

to be licensed at no charge to all third

parties under the terms of this License.

3. You may opt to apply the terms of the

ordinary GNU General Public License

instead of this License to a given

ꢀ

d)If a facility in the modiﬁed Library refers

to a function or a table of data to be

supplied by an application program

that uses the facility, other than as

an argument passed when the facility

is invoked, then you must make a

good faith effort to ensure that, in the

event an application does not supply

such function or table, the facility still

operates, and performs whatever part

of its purpose remains meaningful.

copy of the Library. To do this, you

must alter all the notices that refer to

this License, so that they refer to the

ordinary GNU General Public License,

version 2, instead of to this License. (If

a newer version than version 2 of the

ordinary GNU General Public License

has appeared, then you can specify that

version instead if you wish.) Do not make

any other change in these notices.

Download from Www.Somanuals.com. All Manuals Search And Download.

Once this change is made in a given copy,

it isirreversible for that copy, so the ordinary

GNU General Public License applies to all

subsequent copies and derivative works

made from that copy.

Library, the object code for the work may

be a derivative work of the Library even

though the source code is not. Whether

this is true is especially signiﬁcant if the

work can be linked without the Library, or if

the work is itself a library.

This option is useful when you wish to

copy part of the code of the Library into a

program that is not a library.

The threshold for this to be true is not

precisely deﬁned by law.

4. You may copy and distribute the Library

(or a portion or derivative of it, under

Section 2) in object code or executable

form under the terms of Sections 1 and

2 above provided that you accompany

it with the complete corresponding

machine-readable source code,

If such an object ﬁle uses only numerical

parameters, data structure layouts

and accessors, and small macros and

small inline functions (ten lines or less in

length), then the use of the object ﬁle is

unrestricted, regardless of whether it is

legally a derivative work. (Executables

containing this object code plus portions

of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the

Library, you may distribute the object code

for the work under the terms of Section.

which must be distributed under the

terms of Sections 1 and 2 above on a

medium customarily used for software

interchange.

If distribution of object code is made by

offering access to copy from a designated

place, then offering equivalent access to

copy the source code from the same place

satisﬁes the requirement to distribute the

source code, even though third parties are

not compelled to copy the source along

with the object code.

Any executables containing that work also

fall under Section 6, whether or not they are

linked directly with the Library itself.

6. As an exception to the Sections above,

you may also combine or link a "work

that uses the Library" with the Library

to produce a work containing portions

of the Library, and distribute that work

under terms of your choice,provided

that the terms permit modiﬁcation of the

work for the customer's own use and

reverse engineering for debugging such

modiﬁcations.

5. A program that contains no derivative

of any portion of the Library, but is

designed to work with the Library by

being compiled or linked with it, is called

a "work that uses the Library". Such a

work, in isolation, is not a derivative work

of the Library, and therefore falls outside

the scope of this License.

You must give prominent notice with each

copy of the work that the Library is used

in it and that the Library and its use are

covered by this License. You must supply

a copy of this License. If the work during

execution displays copyright notices, you

must include the copyright notice for the

Library among them, as well as a reference

directing the user to the copy of this

License. Also, you must do one of these

things :

However, linking a "work that uses the

Library" with the Library creates an

executable that is a derivative of the Library

(because it contains portions of the Library),

rather than a "work that uses the library".

The executable is therefore covered by this

License.

Section 6 states terms for distribution of

such executables.

ꢀ

a)Accompany the work with the

When a "work that uses the Library" uses

material from a header ﬁle that is part of the

complete corresponding machine-

Download from Www.Somanuals.com. All Manuals Search And Download.

readable source code for the Library

including whatever changes were used

in the work (which must be distributed

under Sections 1 and 2 above) ; and,

if the work is an executable linked with

the Library, with the complete machine-

readable "work that uses the Library",

as object code and/or source code,

so that the user can modify the Library

and then relink to produce a modiﬁed

executable containing the modiﬁed

Library. (It is understood that the user

who changes the contents of deﬁnitions

ﬁles in the Library will not necessarily

be able to recompile the application to

use the modiﬁed deﬁnitions.)

from it. However, as a special exception,

the materials to be distributed need not

include anything that is normally distributed

(in either source or binary form)with the

major components (compiler, kernel, and

so on) of the operating system on which the

executable runs, unless that component itself

accompanies the executable. It may happen

that this requirement contradicts the license

restrictions of other proprietary libraries that

do not normally accompany the operating

system. Such a contradiction means you

cannot use both them and the Library

together in an executable that you distribute.

7. You may place library facilities that are

a work based on the Library side-by-

side in a single library together with

other library facilities not covered by this

License, and distribute such a combined

library, provided that the separate

distribution of the work based on the

Library and of the other library facilities is

otherwise permitted, and provided that

you do these two things :

ꢀ

b)Use a suitable shared library

mechanism for linking with the Library.

A suitable mechanism is one that

(1)uses at run time a copy of the library

already present on the user's computer

system, rather than copying library

functions into the executable, and

(2)will operate properly with a modiﬁed

version of the library, if the user installs

one,as long as the modiﬁed version is

interface-compatible with the version

that the work was made with.

ꢀ

a)Accompany the combined library with

a copy of the same work based on the

Library, uncombined with any other

library facilities. This must be distributed

under the terms of the Sections above.

ꢀ

c)Accompany the work with a written

offer, valid for at least three years,

to give the same user the materials

speciﬁed in Subsection 6a, above,

for a charge no more than the cost

ofperforming this distribution.

ꢀ

b)Give prominent notice with the

combined library of the fact that part

of it is a work based on the Library,

and explaining where to ﬁnd the

accompanying uncombined form of the

same work.

ꢀ

d)If distribution of the work is made

by offering access to copy from a

designated place, offer equivalent

access to copy the above speciﬁed

materials from the same place.

8. You may not copy, modify, sublicense,

link with, or distribute the Library except

as expressly provided under this License.

Any attempt otherwise to copy, modify,

sublicense, link with, or distribute the

Library is void, and will automatically

terminate your rights under this License.

However, parties who have received

copies, or rights, from you under this

License will not have their licenses

terminated so long as such parties

remain in full compliance.

e)Verify that the user has already received

a copy of these materials or that you

have already sent this user a copy.

For an executable, the required form of

the "work that uses the Library" must

include any data and utility programs

needed for reproducing the executable

Download from Www.Somanuals.com. All Manuals Search And Download.

9. You are not required to accept this

License, since you have not signed it.

However, nothing else grants you

is intended to apply, and the section

as a whole is intended to apply in other

circumstances.

permission to modify or distribute the

Library or its derivative works.

It is not the purpose of this section to

induce you to infringe any patents or other

property right claims or to contest validity of

any such claims ; this section has the sole

purpose of protecting the integrity of the

free software distribution system which is

implemented by public license practices.

These actions are prohibited by law if you

do not accept this License. Therefore,

by modifying or distributing the Library

(or any work based on the Library), you

indicate your acceptance of this License

to do so, and all its terms and conditions

for copying, distributing or modifying the

Library or works based on it.

Many people have made generous

contributions to the wide range of software

distributed through that system in reliance

on consistent application of that system;it

is up to the author/donor to decide if he or

she is willing to distribute software through

any other system and a licensee cannot

impose that choice.

10.Each time you redistribute the Library

(or any work based on the Library), the

recipient automatically receives a license

from the original licensor to copy,

distribute, link with or modify the Library

subject to these terms and conditions.

You may not impose any further

This section is intended to make thoroughly

clear what is believed to be a consequence

of the rest of this License.

restrictions on the recipients’ exercise

of the rights granted herein.You are not

responsible for enforcing compliance by

third parties with this License.

12.If the distribution and/or use of the

Library is restricted in certain countries

either by patents or by copyrighted

interfaces, the original copyright

holder who places the Library under

this License may add an explicit

geographical distribution limitation

excluding those countries, so that

distribution is permitted only in or

among countries not thus excluded.In

such case, this License incorporates the

limitation as if written in the body of this

License.

11.If,as a consequence of a court judgment

or allegation of patent infringement or for

any other reason (not limited to patent

issues), conditions are imposed on you

(whether by court order, agreement or

otherwise)that contradict the conditions

of this License, they do not excuse you

from the conditions of this License. If

you cannot distribute so as to satisfy

simultaneously your obligations under

this License and any other pertinent

obligations, then as a consequence you

may not distribute the Library at all.

For example, if a patent license would

not permit royalty-free redistribution

of the Library by all those who receive

copies directly or indirectly through you,

then the only way you could satisfy both

it and this License would be to refrain

entirely from distribution of the Library.

13.The Free Software Foundation may

publish revised and/or new versions of

the Lesser General Public License from

time to time. Such new versions will be

similar in spirit to the present version,

but may differ in detail to address new

problems or concerns.

Each version is given a distinguishing

version number. If the Library speciﬁes

a version number of this License which

applies to it and "any later version", you

have the option of following the terms and

If any portion of this section is held invalid

or unenforceable under any particular

circumstance, the balance of the section

Download from Www.Somanuals.com. All Manuals Search And Download.

conditions either of that version or of any

later version published by the Free Software

Foundation. If the Library does not specify

a license version number, you may choose

any version ever published by the Free

Software Foundation.

YOU FOR DAMAGES, INCLUDING ANY

GENERAL, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARISING

OUT OF THE USE OR INABILITY TO

USE THE LIBRARY (INCLUDING BUT

NOT LIMITED TO LOSS OF DATA OR

DATA BEING RENDERED INACCURATE

OR LOSSES SUSTAINED BY YOU OR

THIRD PARTIES OR A FAILURE OF

THE LIBRARY TO OPERATE WITH ANY

OTHER SOFTWARE), EVEN IF SUCH

HOLDER OR OTHER PARTY HAS

BEEN ADVISED OF THE POSSIBILITY

OF SUCH DAMAGES.

14.If you wish to incorporate parts of the

Library into other free programs whose

distribution conditions are incompatible

with these, write to the author to ask

for permission. For software which

is copyrighted by the Free Software

Foundation, write to the Free Software

Foundation ; we sometimes make

eNd oF TeRmS ANd CoNdITIoNS

exceptions for this. Our decision will be

guided by the two goals of preserving

the free status of all derivatives of our

free software and of promoting the

sharing and reuse of software generally.

how to Apply These Terms to your

New Libraries

If you develop a new library, and you want

it to be of the greatest possible use to

the public, we recommend making it free

software that everyone can redistribute

and change. You can do so by permitting

redistribution under these terms (or,

alternatively, under the terms of the ordinary

General Public License).

No WARRANTy

15.BECAUSE THE LIBRARY IS LICENSED

FREE OF CHARGE, THERE IS NO

WARRANTY FOR THE LIBRARY,

TO THE EXTENT PERMITTED BY

APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING

THE COPYRIGHT HOLDERS AND/

OR OTHER PARTIES PROVIDE THE

LIBRARY "ASIS" WITHOUT WARRANTY

OF ANYKIND, EITHER EXPRESSED

OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE.THE

ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE LIBRARY IS

WITH YOU. SHOULD THE LIBRARY

PROVE DEFECTIVE, YOU ASSUME THE

COST OF ALL NECESSARY SERVICING,

REPAIR OR CORRECTION.

To apply these terms, attach the following

notices to the library. It is safest to attach

them to the start of each source ﬁle to most

effectively convey the exclusion of warranty

; and each ﬁle should have at least the

"copyright" line and a pointer to where the

full notice is found.

One line to give the library's name and an

idea of what it does.

This library is free software ; you can

redistribute it and/or modify it under the

terms of the GNU Lesser General Public

License as published by the Free Software

Foundation ; either version 2.1 of the

License, or (at your option)any later version.

16.IN NO EVENT UNLESS REQUIRED BY

APPLICABLE LAW OR AGREED TO

IN WRITING WILL ANY COPYRIGHT

HOLDER, OR ANY OTHER PARTY

WHO MAY MODIFY AND/OR

This library is distributed in the hope

REDISTRIBUTE THE LIBRARY AS

PERMITTED ABOVE, BE LIABLE TO

that it will be useful, but WITHOUT ANY

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY ; without even the implied

warranty of MERCHANTABILITY or

FITNESS FOR A PARTICULAR PURPOSE.

See the GNU Lesser General Public

License for more details.

display the following acknowledgment :

"This product includes software

developed by the OpenSSL Project for

use in the OpenSSLToolkit. (http://www.

openssl.org/)"

4. The names "OpenSSL Toolkit" and

"OpenSSL Project" must not be used to

endorse or promote products derived

from this software without prior written

permission. For written permission, please

contact [email protected].

You should have received a copy of the

GNU Lesser General Public License along

with this library ; if not, write to the Free

Software Foundation, Inc.,51 Franklin Street,

Fifth Floor, Boston, MA 02110-1301 USA

Also add information on how to contact you

5. Products derived from this software

may not be called "OpenSSL" nor

may "OpenSSL" appear in their names

without prior written permission of the

OpenSSL Project.

by electronic and paper mail.

You should also get your employer (if you

work as a programmer)or your school, if

any, to sign a "copyright disclaimer" for the

library,if necessary. Here is a sample ; alter

the names:

6. Redistributions of any form whatsoever

must retain the following acknowledgment:

"This product includes software developed

by the OpenSSL Project for use in the

OpenSSL Toolkit (http://www.openssl.

org/)"

Yoyodyne, Inc., hereby disclaims all

library for tweaking knobs)written

by James Random Hacker.

signature of Ty Coon, 1 April 1990

Ty Coon, President of Vice

THIS SOFTWARE IS PROVIDED BY

THE OpenSSL PROJECT “AS IS

” AND ANY EXPRESSED OR IMPLIED

WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED

openSSL LICeNSe

WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN

Redistribution and use in source and

binary forms, with or without modiﬁcation,

are permitted provided that the following

conditions are met :

NO EVENT SHALL THE OpenSSL

PROJECT OR ITS CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES ; LOSS OF USE,DATA,OR

PROFITS ; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR

TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT

OF THE USE OF THIS SOFTWARE, EVEN

IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

1. Redistributions of source code must

retain the above copyright notice, this

list of conditions and the following

disclaimer.

2. Redistributions in binary form must

reproduce the above copyright notice,

this list of conditions and the following

disclaimer in the documentation

and/or other materials provided with the

distribution.

3. All advertising materials mentioning

features or use of this software must

Download from Www.Somanuals.com. All Manuals Search And Download.

This product includes cryptographic

software written by Eric Young (eay@

cryptsoft.com).

and/or other materials provided with the

distribution.

3. All advertising materials mentioning

features or use of this software must

display the following acknowledgement :

"This product includes cryptographic

software written by Eric Young (eay@

cryptsoft.com)" The word 'cryptographic'

can be left out if the rouines from the

library being used are not cryptographic

related :-).

This product includes software written by

Tim Hudson ([email protected]).

original SSLeay License

This package is an SSL implementation

writtenby Eric Young ([email protected]).

The implementation was written so as to

conform with Netscapes SSL.

4. If you include any Windows speciﬁc code

(or a derivative thereof)from the apps

directory (application code) you must

include an acknowledgement :

This library is free for commercial and

noncommercial use as long as the following

conditions are aheared to. The following

conditions apply to all code found in this

distribution, be it the RC4, RSA, lhash,

DES, etc.,code ; not just the SSL code.

"This product includes software written

by Tim Hudson ([email protected])"

THIS SOFTWARE IS PROVIDED

BY ERIC YOUNG “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO,

THE IMPLIED WARRANTIES OF

The SSL documentation included with

this distribution is covered by the same

Tim Hudson ([email protected]).

MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL

THE AUTHOR OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES ; LOSS OF USE, DATA, OR

PROFITS ; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR

TORT (INCLUDING NEGLIGENCE OR

OTHERWISE)ARISING IN ANY WAY OUT

OF THE USE OF THIS SOFTWARE, EVEN

IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

such any Copyright notices in the code are

not to be removed.

If this package is used in a product,Eric

Young should be given attribution as the

author of the parts of the library used.

This can be in the form of a textual

message at program startup or in

documentation (online or textual) provided

with the package.

Redistribution and use in source and

binary forms, with or without modiﬁcation,

are permitted provided that the following

conditions are met :

1. Redistributions of source code must

retain the copyright notice, this list of

conditions and the following disclaimer.

The licence and distribution terms for any

publically available version or derivative of

this code cannot be changed.i.e.this code

cannot simply be copied and put under

another distribution licence [including the

GNU Public Licence.]

2. Redistributions in binary form must

reproduce the above copyright notice,

this list of conditions and the following

disclaimer in the documentation

Download from Www.Somanuals.com. All Manuals Search And Download.

(Waste Electrical & Electronic Equipment)

Correct Disposal of This Product

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger,

headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent

possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other

types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government ofﬁce, for

details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and

its electronic accessories should not be mixed with other commercial wastes for disposal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Q Logic Network Router 59244 00 A User Guide
RCA Flat Panel Television 32LA30RQ User Guide
RCA Microwave Oven RMW1163 User Guide
RedMax Blower EBZ5000Q User Guide
ReliOn Blood Pressure Monitor UA 787REL User Guide
Rival Rice Cooker RC100 User Guide
Samsung Digital Camera EC ST66ZZBPRUS User Guide
Samsung Refrigerator DA99 01220J User Guide
Sanyo CRT Television DS27820 User Guide
Schumacher Power Supply PID 200 User Guide