Index
Main Page
Safety Precautions
Using the Drive
Notational
Installation
While Operating
Other
Using the CD-R/RW Drive
Storing and Cleaning Your Discs
Upgrading the Firmware Flash Memory
System Requirements
Introduction
Troubleshooting
Front
Rear
Solving Recording Problems
Caution with errors
Solving Technical Problems
Setup
Specifications
Installing the CD-R/RW Drive
Connecting the Cables
Installing the CD Record Utility
Installing the Device Driver
Setting Up the Device Driver
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Installation
Place the drive on a level surface.
-
Failure to do so may cause the device to fall onto a hard surface,
resulting in damage or malfunction.
Do not place the drive in direct sunlight.
Avoid low- or high-temperature environments.
Avoid high-humidity environments.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
While Operating
Handle with caution to prevent damage from external shock.
Do not drop the drive, and protect it fromsevere shocks.
- It can damage the drive or cause it to malfunction.
Do not move the drive while in operation and do not attempt to open
the disc tray byforce.
Make sure to close all working programs before attempting to open the
tray and always usethe open/close button.
- Do not insert a pin into the emergency opening while in operation.
Do not use cracked, distorted or damaged discs.
- In particular, a disc with a crack on the inner tracks may break while in
use.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Other
Never allow food particles or foreign substances to enter the drive
casing.
To protect against the risk of fire, do ot spill such liquids as
alcohol and benzene on the drive.
Do not disassemble, attempt to repair or modify the device
without express approval as directed in the manual.
Arbitrary removal of the bezel may cause the disc to pop out
during operation.
-
- To reduce the risk of damage, electric shock, and fire,
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Front
1. Headphone Connector
Connector for stereo headphones with a 3.6 mm stereo mini-jack.
2. Headphone volume control
This headphone volume control adjusts the volume for your headphones. You can only use the
headphone jack and volume control when you have installed the required software utilities. For example,
the Microsoft Windows Media player can be used.
3. Emergency eject hole
if the compartment does not open when you press the Eject button, power off the computer, insert a pin or
unfolded paper clip in the hole and push firmly
4. LED
Indicator Light. (GREEN: Read, RED: Record)
5. Eject button
6. Disc compartment
the compartment opens and closes automatically when you press the Eject button
Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Rear
1. Digital output terminal
You can connect a sound card or MPEG card which support Digital output terminal to your drive using this
two-pin terminal.
2. Sound output terminal
You can connect a sound card to your drive using this four-pin terminal.
This function is not covered in detail in this guide. Refer to the documentation supplied with your sound
card.
3. Master/slave select terminal
Usually, this is a pre-set configuration as illustrated below.
Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it in the correct
position.
4. Interface terminal
This input/output interface terminal is used to connect the 40-pin flat cable from the IDE interface to the
CD-R/RW drive.
5. Power terminal
The power terminal is a four-conductor male plug.
(A : +5V DC)
(B : +12V DC)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Installing the CD-R/RW Drive
To install your CD-R/RW Drive in the PC, proceed as follows.
Make sure that the PC is powered off and disconnected from any power source.
If necessary, attach a horizontal bracket to both sides of the drive.
Remove the cover from a free expansion slot and install the CD-R/RW drive, as shown in the illustration.
Connecting the Cables
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Connecting the power cable
The 4-pin power cable from the internal power unit of your computer must be connected to the power
terminal on the rear of the CD-R/RW drive.
+5V DC
Ground
Ground
+12V DC
1
2
3
4
Cut Side
A -
An improperly connected power cable may cause trouble. Check the direction of the power connector
Note:
and the incline side of the CD-R/RW drive before connecting.
Connecting the E-IDE cable
Insert the IDE cable (40-pin), which is connected to the hard disk to the interface terminal.
(Place the red line of the cable close to the Pin 1.)
When using one E-IDE cable
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the CD-R/RW
drive.
a
b
c
: Slave Drive (Choose the SL Jumper)
: Hard Drive
: MainBoard
When using two E-IDE cable
If there is only one CD-R/RW drive, select MA (Master).
a
c
e
: Master Drive (Choose the MA Jumper)
: MainBoard
b
d
: Hard Drive
: Primary 1
: Secondly 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
If there is two CD-R/RW drive, select MA (Master) / SL (Slave).
a
c
e
: Master Drive (Choose the MA Jumper) b : Slave Drive (Choose the SL Jumper)
: Hard Drive
: Primary 1
d
f
: MainBoard
: Secondly 1
Installing a jumper on the master/slave select terminal
Connect a jumper to the rear side of the CD-R/RW.
If the jumper is connected to MA (Master), it will work in the Master mode.
If the jumper is connected to SL (Slave), it will work in the Slave mode.
If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal
CSEL. (In general, connection to MA is recommended.)
Connecting the audio cable from a sound card
Connect the 4-pin audio cable between the sound output terminal on the CD-R/RW drive and the audio
input terminal on the sound card.
For clearer sound, use a digital output terminal.(Available only for the CAID that supports digital output)
This may not be available for general sound cards.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Installing the CD Record Utility
To record data on a CD-R or CD-RW disc in the CD-R/RW drive, you must first install the CD record utility. For
compatibility reasons, you are recommended to uninstall any existing software of the same type before
installing this utility.
Insert the disc supplied with the CD-R/RW drive in the drive.
Follow the instructions displayed on the screen to install the utility.
Refer to the separate utility documentation for further details.
Store the utility disc in a safe place.
Installing the Device Driver
No additional device driver is needed for Windows 98/2000/ME/XP/NT4.0, as the default Windows device
driver is used. You can check that the CD-R/RW drive has been correctly detected by Windows. To do so,
proceed as follows.
Double-click on the
Double-click on the
Double-click on the
Click on the Device
icon on your desktop.
folder.
My Computer
Control Panel
icon.
System
tab.
Manager
Expand the CD-ROM branch.
The
- *** device name is displayed.
SAMSUNG CD-R/RW SW
The SAMSUNG device driver enables discs in the CD-R/RW drive to be read but not recorded in an MS-DOS
environment; the driver is located in the D driver folder on the CD record utility disc.
Setting Up the Device Driver
Automatic Setup
The device driver is located in the Ddriver folder of the CD Record Utility disc which is provided in the
package.
Insert the
disc into the CD-ROM drive and open the
folder.
Ddriver
CD Record Utility
Run the
file in the
folder.
Ddriver
CDSETUP.EXE
When Setup is successfully completed, click
Reboot the computer.
button or press the
key.
Enter
OK
Manual Setup
Make the
directory.
C:\SAMSUNG
Copy the files from the diskette to the
directory.
C:\SAMSUNG
To do so, type
after the
prompt and press [
entry.
].
Enter
COPY D:\Ddriver * . * C:\SAMSUNG
C:\
Edit the
Add the
file.
CONFIG.SYS
DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000/V
Edit the
Add the
file.
AUTOEXEC.BAT
C:\SAMSUNG\MSCDEX/D:SSCD000
entry.
Reboot the computer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Drive
Using the CD-R/RW Drive
To play audio or video CDs in your CD-R/RW drive, proceed as follows.
Push the power button and boot the computer.
After booting the computer, open the disc compartment by pressing the Eject button.
Insert the disc (CD) with the label on the disc facing upwards and close the disc compartment by
pressing the Eject button. The indicator light comes on.
Play the disc (CD).
Playing Audio CDs
Run the CD player supplied with Windows or your sound card.
You can listen to the CD by connecting headphones to the appropriate connector.
If you have installed the appropriate player, such as Microsoft Windows Media Player, you can adjust the
volume using the headphone volume control on the drive front panel.
If you select digital playback in all versions of Windows Media Player, sounds cannot be output to the headphone jack of the product.
Storing and Cleaning Your Discs
To ensure a long service life for your discs and drive, follow the pre-cautions below when storing and cleaning
your discs.
Do not place a disc in direct sunlight.
Store a disc vertically in a well-ventilated and stable location.
Do not write or attach a label on a disc.
Do not drop a disc or place heavy objects on it.
Do not touch the surface of a disc; hold it by the edges.
To clean a disc, polish lightly from the inside of the disc to the outside with a soft cotton cloth.
Do not leave the disc compartment open when you are not using it.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Drive
Upgrading the Firmware Flash Memory
The product firmware can be upgraded by downloading the updated file from the following Web site:
System Requirements
Before you install the CD-R/RW drive, we strongly recommend that you check that your setup meets the
system requirements listed below.
Item
Description
Intel Pentium II 400MHz(or higher), 64 MB of RAM (or higher) with an 80pin IDE
interface for Ultra DMA.
Computer
Disk space
700 MB minimum
Windows version
Windows 98/2000/ME/XP/NT4.0 (or higher)
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any problems recording via your CD-R/RW drive, follow the appropriate instructions below for the
source that you are using.
Hard Drive
Check whether the source file is corrupted.
Optimize the hard disk by using the Windows defragmenter feature:
START / PROGRAMS / ACCESSORIES / SYSTEM TOOLS / DISC DEFRAGMENTER
Decompress the hard disk if it is compressed.
Make sure that the space available on the hard disk is at least twice the size of the largest file to be
recorded on the disc.
If you wish to record more than 1000 small files:
z
z
z
First create an image file and copy the image file to the disc
Choose the low record speed
Compress small files and then record them
Network Drive
Copy the network drive contents to the hard disk and then from the hard disk to the CD-R/RW drive.
CD-ROM Drive
Clean the source CD, if necessary.
Create an image file and then copy the image file to the CD-R/RW drive.
Check the CD-ROM drive record speed.
There are two recording methods :
z
z
Low-speed (file by file)
High-speed (transfer of an image file from the hard disk
If the transfer speed of the CD-ROM drive is slower than the record speed, reduce the record speed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Caution with errors
Caution with errors
Every CD-R or CD-RW drive records data by applying recording laser onto a CD.
If the CD is damaged or recording data is not possible, you need to remove the following causes of the error
before using the CD.
It is recommended to set a CD-R or CD-RW drive as follows.
Do not work on a multi-tasking environment and remove screen savers.
If you work on a multi-tasking environment while the CD-RW drive is recording/deleting data, Buffer
Under-Run may occur.
Do not allow any external access to the Host PC while recording data.
If another user accesses your printer through a network while you are recording data, errors may occur.
Remove the Auto-Run function of the CD.
If you insert a CD that has the Auto-Run function to a drive connected to a PC while recording/deleting
data, this may cause errors.
How to cancel (select) the Auto-Run function
Cancel (Select) the Auto-Run function in
[Start > Setting > Control Panel System > Device Manager > CD-ROM Setting]
Use image files when you record many small files.
If you use a lot of small size files for recording, this may reduce the transaction rate of the PC. Although
Justlink function is often run, the recording quality may become low.
If you copy a CD from another, you do not require making available space in the hard disk. However,
when you use image files, you need to copy them on the hard disk first and then copy to a CD. In this
case, you need to ensure maximum 700MB of available space in the hard disk for reliable recording
process.
Use an E-IDE cable, which has the specified length (46cm).
Using E-IDE cables longer than 46cm may cause errors during data transaction.
Use only one recording software program.
To install a software program for recording, uninstall any other types or versions of recording software
programs first and then reboot the computer.
Make sure you use the recording software CD (Nero Burning Rom / Roxio Easy CD Creator) provided by
us. Using our software program with others may cause errors in recording.
Term Description
What is Buffer Under-Run?
Every CD-R or CD-RW drive records the data that the Host PC wants to record until the data flow ends.
However, if the buffer becomes empty temporarily, this may cause errors in recording data.
What is Auto-Run?
If inserting a CD into a drive, the operating system executes the Autorun.inf file of the CD automatically.
What is Justlink?
This function is to check the buffer to see if there are data while recording.
If the buffer is empty, it waits at the address and then restarts recording after the buffer is full. You can
avoid Buffer Under-Run problems by applying the above-mentioned principle.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Recommended Disc Types
RITEK , TAIYO YUDEN , MCC , ACER , SKC , BEALL , MPO , CMC , PRODISK , MAXELL , FUJI ,
MCI , POSTECH , TDK , GIGA , PLASMON
CD-R
CD-RW : RICOH , RITEK , MCC , PRODISK , SKC , CMC, ACER
(1X - 4X)
CD-RW
H/S-RW : RICOH , CMC , RITEK , ACER , PRODISK , SKC
(10X / 12X / 16X)
General DMA Installation Guide Windows 98/Me
Important!
Please read the entire DMA installation guide before installing your CD-R/RW drive.
About DMA Installation
For stable writing performance at high speeds, Installation of DMA transfer mode for E-IDE/ATAPI
interface is strongly recommended. We recommend DMA mode for fast writing.
DMA Setting
Before you install your CD-R/RW drive, we recommend to set DMA to enabled on your PC system. See
the following procedure to set DMA transfer mode in windows oprerating system.
(Windows 98/ME)
Click on START
Select your CD-R/RW drive
Click on the Properties button
Click on the Settings tab
Check the DMA checkbox to enables DMA.
Click OK
+
+
+
+
+
+
+
+
+
+
+
Click on Settings
Select Control Panel
Select the System Icon
Select the Device Manager panel
in System Properties
Restart your PC
Expand the CD-ROM icon
+
Windows 2000/XP
Select the DMA mode by selecting
[Start > Setting > Control Panel > System > Device Manager > IDEATA/ATAPI Controller >
Default/Assistant IDE Channel Advanced Information]
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Meaning / Solution
Check that the power, audio and IDE cables are correctly connected
to the computer.
The CD-R/RW drive is not
detected by the computer.
After installing the CD-R/RW
drive, the PC gets slower.
Change the IDE cable and reconnect it to the computer.
Preferably, connect a second IDE cable to the CD-R/RW drive in
master mode.
Check the position of the jumper in the master/slave select terminal.
Reinstall the device driver or update it with the latest version by
downloading it from the Samsung Web site.
The CD-R/RW drive is not
recognized by MS-DOS.
-
-
Http://samsung-ODD.com
Http://samsung.com
This case may occur when there is a Windows installation problem;
reinstall Windows.
The CD-R/RW drive is not
detected by Windows.
Check whether the audio cable is correctly connected to the sound
output terminal on the CD-R/RW drive and the sound card CD-IN
terminal.
No sound is heard from an
audio CD.
Check that the sound card is operational.
Adjust the volume control.
Run the CD player supplied with Windows or your sound card.
You can listen to the CD by connecting headphones to the
appropriate connector.
If you have installed the appropriate player, such as Microsoft
Windows Media Player, you can adjust the volume using the
headphone volume control on the drive front panel.
If you select DIGITAL at CD Audio Play in Media Player of Windows
ME/XP, the earphone does not appear in the Digital Mode.
Check whether the CD is of good quality and clean it, if necessary.
Check that the power cable is correctly connected.
A CD is not read or is read
too slowly.
The disc compartment will
not open.
Power off and disconnect the PC.
Insert a pin or unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
Adjust the size of the replay screen.
When the MPEG software
plays a Video CD, the pictures
are not regular and the running
speed is too slow.
After checking the display resolution, adjust it, if necessary.
The computer may not recognize the disc if you start playback too
quickly after inserting the disc. Open and close the disc
compartment and try again.
The Disc is not in message is
displayed even though a disc
has been inserted.
Clean the disc and try again.
The interface mode of the sound card is AT-BUS.
You must therefore connect the CD-R/RW drive to the IDE port on
the PC mother board, rather than to the sound card, or install an E-
IDE compatible sound card.
The CD-R/RW drive is not
detected after it is connected to
a sound card.
Right-click the mouse on TRAY ICON (right side of the menu bar at
the bottom of the monitor) and then select "Eject" to take the CD
out.
IN CD has the Formatted
Disc Eject function.
Select the drive where the disc is inserted from Windows Explorer.
Right-click the mouse and select "Eject" to take the CD out.
This seems to occur when you select the recording function as the
system selects "Image Recorder" instead of SW-248.
In this case, select a recorder from the menu items at the upper part
of NERO or Easy CD Creator and then select SW-248 from the
Recorder Selection window.
When recording NERO or Easy
CD Creator,
it will be recorded not on a
CD but a form of image file.
When installing the recording software, try not to install the software
before the ROM drive as this makes the Image Recorder selected.
Use the firmware automatic upgrade function available at the ODD
service website to download
The Recorder cannot
recognize the disc.
the newest firmware and then reinstall the recording software which
is included in the bundle.
-
-
Http://samsung-ODD.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
continually strives to improve its products. Both the design specifications and these user
SAMSUNG
instructions are thus subject to change without notice.
Technical Specifications
SW-248B
ITEM
CD-RW
Disc types
supported
in read mode
CD-DA(Audio), CD-ROM, CD-ROM XA, CD-Plus, CD-Extra,
Photo-CD(Single, Multi-session), Video CD ready, Enhanced CD,
CD-I/FMV, CD-R, CD-RW, CD-TEXT
DISC
Erasing disc types CD-RW
Disc diameter
120 mm or 80 mm
Data transfer rate Recording CD-R:
DRIVE
7200 KB/sec. (48X),
6000 KB/sec. (40X),
4800 KB/sec. (32X),
3600 KB/sec. (24X),
2400 KB/sec. (16X),
1800 KB/sec. (12X),
1200 KB/sec. (8X),
600 KB/sec. (4X),
PERFORMANCE
CD-RW:
,
2400 KB/sec. (16X),
1800 KB/sec. (12X),
1200 KB/sec. (8X),
600 KB/sec. (4X),
Reading
CD-R:
CAV 48X
CD-RW:
CAV 40X
PIO Mode 4:16.6MB/sec
Multiword DMA mode 2 : 16.6MB/sec
UDMA mode 2 : 33.3MB/sec
Access time
(Random)
110ms
Data Buffer
8MB
Laser
Semiconductor laser
Slide mechanism
Spindle motor
Load mechanism
Stepping motor
Brushless motor
Tray. DC motor (Soft Eject). Horizontal/Vertical.
-12
-9
ERROR RATE
Mode 1: 1 block/10 , Mode 2: 1 block/10
Eject button
Indicator
Auto eject or Auto inject
FRONT PANEL
Play / Read (GREEN) Record (RED), Operation LED
Headphone output Stereo mini-jack (Ø 3.6 mm) 0.65 ± 20% (vrms) 33 ohm
Volume control
Required power
Dial type
+5 VDC: 1.5 A (RMS), +12 VDC: 1.5 A (RMS)
REAR PANEL
Interface connector ATAPI BUS (E-IDE)
Audio output
Jumper block
Operations
Storage
Line out 0.75V ± 20% (vrms) : 47Kohm
Molex 70203 or other compatible models
Temperature: 5~45°C Humidity: 10~80%
Temperature: -25~60°C Humidity: 10~90%
148.2 (W) x 42 (H) x 184 (D) mm (including bezel)
770 g
OPERATING
ENVIRONMENT
Dimensions
Net weight
MTBF
GENERAL
125,000 POH(Duty 20%)
RELIABILITY
"Design and specifications are subject to change without prior notice."
Download from Www.Somanuals.com. All Manuals Search And Download.
|