OPERATOR’S MANUAL
MITER SAW UTILITY VEHICLE
AC9944
Your miter saw utility vehicle has been engineered and manufactured to our high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
WHEN HAULING THE WORKSTAND IN A VEHICLE,
securely tie it down to prevent movement and possible
damage.
Safe operation of this accessory requires that you read and
understand this operator’s manual, the operator’s manual
for the miter saw, and all labels affixed to the tool.
NEVER put the workstand where operators or
bystanders are forced to stand with any part of their
body inline with the path of the saw blade.
READ ALL INSTRUCTIONS
KNOWYOURACCESSORY.Readtheoperator’smanual
carefully. Learn the product’s applications and limitations
as well as the specific potential hazards related to this
product.
NEVER STAND ON WORKSTAND. Serious injury could
occur if the stand tips or you accidentally hit the cutting
tool. Do not store any items above or near the stand
where anyone might climb on the stand to reach them.
MAXIMUM WEIGHT OF POWER TOOL MUST NOT
EXCEED 100 POUNDS.
MAXIMUM WEIGHT OF SAW AND WORKPIECE
MUST NOT EXCEED 200 POUNDS.
ALWAYS MOUNT MITER SAW so the workpiece is
positioned in-line with the roller assemblies.
CHECK TO MAKE SURE WORKSTAND DOES NOT
KEEP THE WORK AREA CLEAN. Cluttered work areas
and work benches invite accidents. DO NOT leave tools
or pieces of wood on the saw while operating.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses; they are NOT safety glasses.
DO NOT USE THIS PRODUCT WITH OTHER
EQUIPMENT or for other purposes.
ALWAYS DISCONNECT THE SAW FROM THE POWER
SUPPLY BEFORE ASSEMBLING THIS KIT. Make sure
the switch is off when reconnecting the saw to a power
supply.
ROCK, SLIDE OR MOVE PRIOR TO USE.
PUT THE WORKSTAND ON A FIRM LEVEL SURFACE
where there is plenty of room to handle and properly
support the workpiece.
ALWAYS move mounted saw to the wheeled end of
stand prior to transporting or taking down unit and
ensure saw mounting brackets are securely locked.
SAVE THESE INSTRUCTIONS. Refer to them frequently
and use them to instruct other users. If you loan someone
this product, also loan these instructions.
BEFORE MAKING A CUT, BE SURE ALL
ADJUSTMENTS ARE SECURE.
ALWAYS GET HELP IF YOU NEED TO LIFT THE
WORKSTAND. When lifting, hold the workstand close
to your body. Bend your knees so you can lift with your
legs, not your back.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
Do not expose to rain or use in damp locations.
Wet Conditions Alert
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
The following signal words and meanings are intended to explain the levels of risk associated with this
product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION:
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
WORK
SUPPORT
WORK STOP
QUICK RELEASE
SAW MOUNTING
BRACKETS
WORK
SUPPORT BRACKET
LIFT ASSIST
HANDLE
EXTENSION
ARM
LEG
SUPPORT
TRANSPORT
HANDLE
SUPPORT
LEG
Fig. 1
TOOLS NEEDED
The following tools (not included) are needed for assembly:
SCREWDRIVER
ADJUSTABLE WRENCH(S)
Fig. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS
The following items are included with your miter saw workstand:
Workstand Assembly
Quick Release Saw Mounting Brackets (2)
Work Supports (2)
LOCK NUTS (4)
WORK
SUPPORTS (2)
Work Support Brackets (2)
Adjustment Knobs (4)
End Caps (2)
Wheels (2)
Hex Bolts, M10 (2)
Washers, 24 x 13 x 2 (2)
Washers, 20 x 10.5 x 1.5 (2)
Lock Nuts, M10 (2)
SPRING
WASHERS (8)
ADJUSTMENT
KNOBS (4)
WORK
HEX BOLTS (4)
SUPPORT
BRACKETS (2)
Leg Supports (2)
Hex Bolts, M6 x 48 (4)
Spring Washers, 16 x 6.5 x 1.5 (8)
Lock Nuts, M6 (4)
QUICK RELEASE
SAW MOUNTING
BRACKETS (2)
LEG
SUPPORTS (2)
Transport Handle
Screws, M6 x 38 (3)
Spring Washers, 16 x 6.5 x 1.5 (3)
Lock Nuts, M6 (3)
Hex Bolts, M6 (2)
Flat Washers, 16 x 6.5 x 1.5 (2)
Plastic Washers, 19 x 6.8 x 2 (2)
Lock Nuts, M6 x 55 (2)
Blister Packs - Saw Mounting Hardware
(Not Shown) (2)
WORKSTAND
ASSEMBLY
Operator’s Manual (Not Shown)
LOCK NUTS (2)
FLAT
WASHERS (2)
PLASTIC
WASHERS (2)
WHEELS (2)
WASHERS (2)
HEX
BOLTS (2)
HEX BOLTS (2)
LOCK NUTS (2)
SPRING
WASHERS (3)
TRANSPORT
HANDLE
LOCK NUTS (3)
WASHERS (2)
END CAPS (2)
WASHERS (3)
SCREWS (3)
Fig. 3
WARNING:
The use of attachments or accessories not listed in this manual might be hazardous and could cause serious
personal injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACKING
This product requires assembly.
RAISE
LEGS
LEG SET
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Inspect the product carefully to make sure no breakage
RELEASE
LEGS
or damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
LOCK
LEGS
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Failure to
heed this warning could result in serious personal
injury.
LOCK
KNOB
Fig. 4
WHEEL
RAISE WHEEL
LEGS AND LOCK
INTO POSITION
ROTATE
RELEASE LEVER
WARNING:
LIFT ASSIST
HANDLE
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
3
CABLE
TIE
4
1
WARNING:
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
2
HOLD WHEEL LEG
SET FIRMLY
PREPARING THE WORKSTAND FOR
ASSEMBLY
See Figures 4 - 5.
SPRING LOADED
WHEEL LEG SET
With workstand out of box and packaging removed, place
Fig. 5
unit upside down on ground.
Pull lock knob on leg set and raise legs until locked into
Pull up on lock mechanism release lever and carefully
open position.
raise wheel legs.
Rotate lift assist handle to operational position.
Continue to raise wheel leg set until locked into
While holding spring loaded wheel leg set firmly, cut cable
position.
tie.
CAUTION:
Wheel legs are spring loaded. Hold wheel legs
to prevent from snapping up when releasing lock
mechanism release lever. Failure to do so may
result in possible injury.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
SECURING THE LIFT ASSIST HANDLE
See Figures 5 - 6.
WASHER
Insert hex bolt into hole on each side of handle but do
HEX BOLT
not insert through stand table.
LOCK NUT
Insert plastic washer between handle and stand table onto
the bolt. Push bolt through the hole in the stand table.
Place a washer and lock nut over each bolt and secure.
Do not overtighten.
ATTACHING THE LEG SUPPORTS
See Figure 7.
PLASTIC
WASHER
Insert leg support into wheel leg set with foot peddle side
facing down toward lift assist handle. Align the two holes
in the leg support with the holes in the assembly.
Place a spring washer over the hex bolt and insert up
through each leg hole.
LIFT ASSIST
HANDLE
Place a spring washer and lock nut over end of each bolt
and secure.
HEX BOLT
Fig. 6
Repeat on other side.
WHEEL LEG
SET
LEG SUPPORT
LOCK
NUT
SPRING
WASHER
SPRING
WASHER
HEX BOLT
Fig. 7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
ATTACHING THE TRANSPORT HANDLE
See Figure 8.
TRANSPORT
HANDLE
Align transport handle ends with holes in stand table end
caps and insert.
Place a spring washer over the screw and insert screw
through each hole of the handle and leg support
bracket.
Place a washer and lock nut over the end of each screw
and secure.
ATTACHING THE WHEELS
See Figure 9.
Insert bolt through wheel leg set.
Place washer and then wheel over bolt.
Place washer and lock nut over end of bolt and secure.
Do not overtighten.
LOCK NUT
SPRING
WASHER
SCREW
WASHER
Fig. 8
END CAP
WASHER
Place end cap over lock nut.
WHEEL
Repeat on other side.
After wheels are installed and all previous assembly
procedures have been followed, workstand may be turned
over to rest on its legs.
WASHER
NOTE: The workstand is heavy. Get help when needed.
HEX BOLT
INSTALLING THE WORK SUPPORTS
See Figure 10.
LOCK NUT
The work supports support the workpiece during cutting
operations.
To install the work supports:
LEG
Loosen lock lever and slide extension arm out for
ASSEMBLY
accessibility.
Position work support bracket so that the work support
shaft is positioned in the center of the stand table.
Fig. 9
Align large square hole in work support bracket with end
of extension arm and slide bracket over rail.
Insert the work support in shaft of bracket.
Insert adjustment knob through knob hole in shaft of
bracket and tighten to secure into position.
WORK
Insert adjustment knob through knob hole on top of
SUPPORT
ADJUSTMENT
KNOB
bracket and tighten to secure into position.
Repeat on the other side.
SHAFT
Ensure workstand is stable and can be opened and
locked.
WORK
SUPPORT
BRACKET
EXTENSION
ARM
LOCK LEVER
TIGHTEN
LOOSEN
Fig. 10
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
WARNING:
HEX NUT
The saw mounting brackets are designed to fit
snugly over the table edges with locking levers in
the open position. With the locking levers in the
lowered (locked) position, you should not be able
to slide the saw mounting bracket assembly along
the table edges or remove the bracket assembly
from the table edges. If the saw mounting brackets
will not fit over the edges, or if the brackets can
be removed from the edges when the levers are
locked, remove bracket assembly immediately
and adjust bracket adjustment screw. See the
Maintenance section of this manual. Failure to heed
this warning may result in serious personal injury.
LOCK
WASHER
FLAT WASHER
35
40
45
SAW ARM
SLIDING
ADJUSTMENT
PLATE
ATTACHING SAW TO THE MOUNTING
BRACKETS
See Figures 11 - 12.
STABLE
CARRIAGE
BOLT
SUPPORT
Always position the saw to achieve maximum balance and
stability. All four corners of the saw must be bolted to the
mounting brackets before use. Make sure bolts do not
extend above the table of the miter saw.
CARRIAGE BOLT
LOADING SLOTS
SAW
MOUNTING BRACKET
Fig. 11
NOTE: Four additional 1-1/2 in. bolts have been provided
for use when securing a sliding miter saw to the mounting
brackets.
NOTE: Ensure that mounting brackets can be clamped
securely onto stand before mounting saw. If locking lever on
saw mounting bracket cannot easily be pushed down into
the closed position, the adjustment screw is too tight. Do
not force locking lever into the closed position. Loosen the
adjustment screw. Refer to the Maintenance section later in
this manual for mounting bracket adjustment.
HEX NUT
LOCK
WASHER
FLAT WASHER
35
45
40
If the saw has mounting holes that line up with the slots
in the saw mounting brackets:
Disconnect the saw from power supply and lock the saw
arm in the down position.
Place a 2 x 4 or similar type of stable support underneath
the saw to raise the saw and allow access to the saw’s
mounting feet.
MOUNTING
SURFACE
HEX BOLT
Feed a carriage bolt up through each side of the bracket
SAW
MOUNTING
BRACKET
and adjustment plate.
Align bolts in the two sliding adjustment plates on the
saw mounting bracket with the saw mounting holes.
CARRIAGE BOLT
Fig. 12
Place the saw mounting bracket underneath the raised
side of the saw, and insert bolts through mounting holes
in saw.
Disconnect the saw from power supply and lock saw arm
in the down position.
Loosely secure in place using a flat washer, lock washer,
and hex nut.
Mount the saw to a mounting surface at least 1/2 in.
thick using 5/16 hex head bolts, washers, and nuts (not
included).
Repeat procedure to attach second bracket to saw.
After making sure both brackets are parallel to each other,
Drill holes in the mounting surface to match the sliding
lightly tighten all four nuts to hold in position.
adjustment plates in the saw mounting brackets.
If the saw has holes that do not line up with the sliding
adjustment plates in the saw mounting brackets:
Proceed with installation as previously described.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
NOTE: Continue to hold the saw and bracket assembly
with one hand until both levers are securely locked.
MOUNTING THE MITER SAW TO THE
WORKSTAND
See Figures 13 - 14.
Check position and adjust, if necessary, to make sure the
weight of the saw is evenly balanced over the edges.
Use the handles located at the rear of the saw mounting
brackets to aid in installing or removing saw and bracket
assembly.
Ensure the saw is fully seated and locked in position, then
securely tighten the four nuts holding the saw to the saw
mounting brackets.
Lift the saw and bracket assembly, allowing the assembly
to tilt slightly toward your body.
While still tilted toward you, hook the front clamp of the
saw and bracket assembly onto the front edge of the
table.
WARNING:
The saw mounting brackets are designed to fit
snugly over the table edges with locking levers in
the open position. With the locking levers in the
lowered (locked) position, you should not be able
to slide the saw mounting bracket assembly along
the table edges or remove the bracket assembly
from the table edges. If the saw mounting brackets
will not fit over the edges, or if the brackets can
be removed from the edges when the levers are
locked, remove bracket assembly immediately
and adjust bracket adjustment screw. See the
Maintenance section of this manual. Failure to heed
this warning may result in serious personal injury.
WARNING:
To avoid serious personal injury, make sure the
curved front edge of the mounting brackets are
securely seated over the front edge of table before
seating the other end of the brackets. Failure to
do so could cause you to lose control of the saw
and bracket assembly, which could cause serious
personal injury.
Lower the saw and bracket assembly to allow the rear
clamp of the bracket to seat fully over the rear table
edge.
Lock the brackets in position by lowering the locking
levers.
35
40
45
35
40
45
HANDLES
PUSH DOWN AND
BACK TO LOCK
LOCKING LEVER
Fig. 13
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
LOCKING LEVER
To remove saw from workstand:
RELEASE BUTTON
Push locking lever release buttons and raise the locking
levers to unlock the saw mounting brackets assembly.
PUSH IN AND
LIFT TO UNLOCK
Grasp the handles on either side of the assembly and lift
away from the rear edge of the table to disengage.
With the assembly tilted slightly toward you, lift the front
part of the assembly to disengage from the front edge of
the table.
LIFT TO
RELEASE LEVER
CAUTION:
LOCKING LEVER
Do not mount miter saw to workstand before
ensuring workstand can be opened and locked
securely. Failure to do so may result in possible
injury and damage to the tool.
OPENING THE WORKSTAND
See Figures 15 - 16.
SETUP:
NOTE: If saw is mounted, ensure that saw is in folding
30
45
40
35
transportation position. See figure 17.
From the upright position, pull the lock knob and lift legs
up until the spring pin locks into place.
WARNING:
Fig. 14
To reduce the risk of injury, make sure leg set is
secured in the notch by the lock knob. Failure to
latch may cause workstand to fall in use.
SETUP
INST
AL
LA
TION
INST
AL
E
FOLD DOWN
PLI VERS
L
E
DOBLEZ ABA
J
BA
S
O
Slowly lower workstand until the legs rest on the
ground.
E
N
S
U
R
A
E
T
-
AS
L
“
W
A
VER
E
N
H
E
E
A
E
TR
OU
VE
L
I
TISSEM
D
”
À
L
A
O
F
S
M
É
ÊM
Stand at wheel end of workstand and grasp the lift assist
handle. Push down on lock mechanism release lever and
lift workstand into raised position.
E
N
S
T
EL
E
EX
TR
ÉM
IT
A
E
NT
EX
N
TR
D
EM
O
É
B
E
DE
DU
F
O
PO
RT
L
B
AN
CO
S
UP
R
E
CO
F
ADVE
IN
RR
O
L
OU
ES
PO
Q
UE
D
ND
L
ES
IE
NT
R
G
/
R
TENC
E
A
T
LA
ES
R
A
S
A
VA
N
S
RU
ED
AS
NT
D
E
P
O
IA
IN
G
AN
TE
PL
IE
R/
TR
AN
R
S
T
DE
DE
SP
LE
GA
R/
TR
AN
SP
SP
OR
TE
R
OR
T
A
R
Miter
NOTE: The workstand is heavy. Get help when needed.
WARNING:
To avoid serious personal injury when lifting, bend
your knees so you can lift with your legs, not your
back.
LOCK MECHANISM RELEASE LEVER
Fig. 15
CAUTION:
Do not lift by any part of the miter saw that is
attached to the workstand. Failure to heed this
warning may result in possible injury and damage
the tool.
Step on leg support while lifting table up by lift assist
handle. Thewheelsshouldmovefurtherunderworkstand
until unit is locked into place.
Ensure workstand is locked into position before use.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
CLOSING AND MOVING THE WORKSTAND
See Figures 15 - 17.
SETUP
INSTALLATION
INSTALE
FOLD DOWN
PLI VERS LE BAS
DOBLEZ ABAJO
NOTE: The workstand is heavy. Get help when needed.
If a miter saw is assembled on the stand, make sure
to place the blade 90° to the table (if applicable), miter
the blade to the right as far as it will go, place the blade
in the “locked down” position, and lock all knobs and
levers.
NOTE: If a sliding compound miter saw is mounted on the
stand, it may be necessary to slide the power head/blade
assembly forward and lock in place when going through
doorways or other narrow openings.
Remove any workpieces, clamps, or other accessories
from saw.
FOLD DOWN:
Move miter saw to wheel end of workstand and secure
per the instructions in this manual. See figure 17.
Make sure extension arms and support legs are retracted
into position behind transport handle and lift assist
handle.
While securely gripping lift assist handle, push down lock
mechanism release lever to release wheel leg set.
Slowly push stand down to the ground in one controlled
movement.
CAUTION:
Leg supports will move toward you when stand is
being lowered. Be aware of their position to avoid
possible injury.
SECURELY GRIP AND HOLD ASSIST HANDLE FIRMLY WHEN SETTING UP OR FOLDING DOWN STAND
SERREZ BIEN ET TENEZ FERMEMENT LA POIGNÉE AUXILIAIRE QUAND VOUS OUVREZ OU PLIEZ LE SUPPORT
SUJETE Y SOSTENGA EL MANGO DE APOYO FIRMEMENTE Y EN FORMA SEGURA AL DESPLEGAR O PLEGAR EL BANCO
Fig. 16
Use transport handles to lift stand into upright position.
Make sure the stand will remain upright on its own.
CAUTION:
If the stand will not remain upright, store in the
horizontal position.
Pull the lock knob and push leg set in under workstand
until they lock into place.
AVERTISSEMENT
ADVERTENCIA
The workstand can be moved by pulling or pushing. To
keep the stand from tipping over, pulling the stand is the
preferred method when moving over a door threshold,
crack, or up stairs.
ENSURE TOOL IS AT “WHEEL END” OF STAND BEFORE FOLDING/ TRANSPORTING
ASSUREZ-VOUS QUE L’OUTIL SE TROUVE À LA MÊME EXTRÉMITÉ DU SUPPORT QUE LES ROUES AVANT DE PLIER/TRANSPORTER
ASEGÚRESE DE QUE LA HERRAMIENTA ESTÉ EN EL EXTREMO DEL BANCO CORRESPONDIENTE A LAS RUEDAS ANTES DE DESPLEGAR/TRANSPORTAR
Fig. 17
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
EXTENSION ARM
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating products. Failure to do
so could result in objects being thrown into your
eyes resulting in possible serious injury.
ADJUST IN - OUT
EXTENSION
ARM LOCKING
LEVER
TIGHTEN
WARNING:
LOOSEN
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal
injury.
Fig. 18
LATCH ON
PULL LEG
UNDERSIDE
EXTENSION OUTWARD
HINGE
POINT
APPLICATIONS
You may use this product for the purpose listed below:
RELEASE
BUTTON
To provide a stable, secure work surface for a miter
saw
USING THE EXTENSION ARMS AND
SUPPORT LEGS
See Figures 18 - 19.
PULL
LEG DOWN
Use the extension arms when working with larger workpieces.
Both extension arms may be adjusted to provide maximum
workpiece support.
EXTENSION
ARM
To extend the extension arms:
Loosen the extension arm locking lever.
Extend the extension arm to the desired position.
Tighten the extension arm locking lever.
To extend the support legs:
SUPPORT LEG
Press latch at end of extension arm and pull leg outward
from arm until hinge is fully exposed. The leg will bend
at hinge and face in a downward position.
Press and hold latch in middle of support leg. Extend
adjustment leg completely to the ground.
ADJUSTMENT
LEG
EXTENSION
ARM LOCKING
LEVER
To retract extension arms and support legs:
Press and hold latch in middle of support leg to release
adjustment leg. Push adjustment leg into support leg until
it locks into place.
Push release button on hinge and rotate support leg into
horizontal position. Push support leg into extension arm
until locked into position.
LATCH
Unlock the extension arm locking lever.
Push extension arm fully into stand for storage.
Lock the extension arm locking lever.
ADJUST LEG
EXTENSION UNTIL STABLE
Fig. 19
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
To adjust the work support:
USING THE WORK SUPPORT
See Figure 20.
Loosen the work support height adjustment knob.
Adjust the work support to the desired position.
Tighten the work support height adjustment knob.
Lower extension arm support leg.
Rest the workpiece on top of the work support to support
the workpiece during cutting operations.
NOTE: More than one work support can be used on an
extension arm at a time when extra support is necessary.
Always lower extension arm support legs when using work
supports.
To adjust work support distance:
Loosen the work support distance adjustment knob.
Slide the work support to the desired position along the
Rest the workpiece on the work support work stop whenever
you need to make repetitive cuts of the same size.
extension arm.
Tighten the work support distance adjustment knob.
NOTE: To avoid a greater risk of binding or pinching, do
not use both work support at the same time when using the
work stop feature.
Lower extension arm support leg.
WORK SUPPORT
ADJUST WORK
SUPPORT UP AND DOWN
DISTANCE
ADJUSTMENT KNOB
ADJUST
WORK SUPPORT
IN AND OUT
WORK STOP
30
45
40
35
HEIGHT
ADJUSTMENT KNOB
EXTENSION ARM
SUPPORT LEG
Fig. 20
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
LOCK MECHANISM HINGE
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Periodically check all fasteners for tightness. Retighten as
necessary.
CLEANING AND LUBRICATING
See Figures 21 - 22.
Fig. 21
Clean and lubricate the lock mechanism hinge.
SPRING CYLINDER SHAFT
Lubricate the spring cylinder shaft.
Fig. 22
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WRENCH
SAW
MOUNTING
BRACKET
WARNING:
The saw mounting brackets are designed to fit
snugly over the table edges with locking levers in
the open position. With the locking levers in the
lowered (locked) position, you should not be able
to slide the saw mounting bracket assembly along
the table edges or remove the bracket assembly
from the table edges. If the saw mounting brackets
will not fit over the edges, or if the brackets can
be removed from the edges when the levers are
locked, remove bracket assembly immediately and
adjust bracket adjustment screw. Failure to heed
this warning may result in serious personal injury.
SAW MOUNTING BRACKET ADJUSTMENT
See Figure 23.
SCREWDRIVER
If the saw and bracket assembly can slide over the table
edges or be removed from the table edges when the levers
are locked, the bracket adjustment screws need to be
tightened. If the saw and bracket assembly will not fit over
both table edges, the bracket adjustment screw needs to
be loosened.
NUT
BRACKET
ADJUSTMENT
SCREW
SCREWDRIVER
ACCESS HOLE
NOTE: The saw should be removed from the mounting
brackets before attempting to tighten or loosen the bracket
adjustment screws.
Fig. 23
To adjust:
Use a wrench to slightly loosen the nut.
Turn the screw with a phillips screwdriver. Rotate
clockwise if the bracket assembly needs to be tightened
or counterclockwise if the assembly needs to be
loosened.
NOTE: If locking lever on saw mounting bracket cannot
easily be pushed down into the closed position, the
adjustment screw is too tight. Do not force locking lever
into the closed position. Loosen the adjustment screw.
Install the bracket on the front table edge then lower
bracket to allow the rear clamp of the bracket to seat
fully over the rear table edge.
NOTE: The mounting bracket should fit snugly over the
table edges when in the open position.
When the correct position is achieved, wrench-tighten
the nut to secure.
Repeat with the second mounting bracket.
To purchase additional saw mounting bracket assemblies
(part no. 900510802), call RIDGID customer service at
1-866-539-1710.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
18
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting
warranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at
retail and may not be transferred. This warranty only covers
defects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than
an authorized service center for RIDGID® branded hand
held and stationary power tools. Consumable accessories
provided with the tool such as, but not limited to, blades,
bits and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied
warranties, including warranties of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE, are disclaimed.
Any implied warranties, including warranties of merchant-
ability or fitness for a particular purpose, that cannot be
disclaimed under state law are limited to three years from the
date of purchase. One World Technologies, Inc. and RIDGID,
Inc. are not responsible for direct, indirect, incidental or
consequential damages. Some states do not allow
limitations on how long an implied warranty lasts and/or
do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state
to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and
normal wear items such as brushes, chucks, motors, switch-
es, cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service cen-
ter nearest you by calling (toll free) 1-866-539-1710 or by
logging on to the RIDGID® website at www.ridgid.com.
When requesting warranty service, you must present the
original dated sales receipt. The authorized service center will
repair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
MITER SAW UTILITY VEHICLE
AC9944
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this product is found on a plate attached to the bottom of the
table. Please record the serial number in the space provided below. When ordering
repair parts, always give the following information:
AC9944
Model No.
Serial No.
987000-043
1-11-07 (REV:01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|