RICOH
FAX1700L
Re a d the sa fe ty instruc tio ns o n p a g e i to iv
Op e ra tor’s Ma nua l
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional equipment
PAPER FEED UNIT TYPE 70
A paper feed unit can be added to the base machine.
FAX EXPANSION CARD TYPE 10
A 1-Mbyte memory card can be added.
FAX EXPANSION CARD TYPE 20
A 2-Mbyte memory card can be added.
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Use of control or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure
Shielded interconnect cables must be employed with this
equipment to ensure compliance with the pertinent RF
emission limits governing this device.
In accordance with ISO 7001, this machine uses the following
symbols for the main switch:
means POWER ON
means POWER OFF
WARNING
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the machine.
Operator Safety
This machine is classified as class 1 laser device according to
EN60825. The Facsimile contains a 5-milliwatt, 770-810
nanometer wavelength, AIGaAs laser diode.
Direct (or indirect reflected eye contact with the laser beam
may cause serious eye damage. Safety precautions and
interlock mechanisms have been designed to prevent any
possible laser beam exposure to the operator.
oad from Www.Somanuals.com. All Manuals Search And Dow
SAFETY
Im p orta nt Sa fe ty Instruc tions
All safety messages in the main text of this manual are labeled WARNING or
CAUTION. These mean the following:
WARNING: Important information to alert you to a situation that might cause
serious injury and damage to your property if instructions are not
followed properly.
CAUTION: Important information that tells how to prevent damage to your
equipment or how to avoid a situation that might cause minor injury.
In addition to the warnings and cautions included in the text of this manual,
please read and observe the following safety instructions.
1
2
3
4
Read all of these instructions.
Save these instructions for later use.
Follow all warnings and cautions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
5. Do not use this product near water.
6. Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious damage to the product or injuring the user.
7. Slots and openings in the cabinet and the back or bottom are provided
for ventilation; to ensure reliable operation of the product and to protect
it from overheating, these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not be placed in a
built-in installation unless proper ventilation is provided.
8. This product should be operated from the type of power source
indicated on the marking label. If you are not sure of the type of power
available, consult an authorized sales person or your local power
company.
9. This product is equipped with a 3-wire grounding type plug, a plug having a
third (grounding) pin. This plug will only fit into a grounding-type power
outlet. This is a safety feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet. Do not defeat
the purpose of the grounding type plug. (This does not apply in countries in
which the 2-wire, non-grounded type of plug is used.)
i
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Whe n to Ca ll Your Se rvic e Re p re se nta tive
10. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
11. If an extension cord is used with this product, make sure that the total of
the ampere ratings on the products plugged into the extension cord
does not exceed the extension cord ampere rating. Also, make sure that
the total of all products plugged into the wall outlet does not exceed 15
amperes.
12. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short out parts that could
result in a risk of fire or electric shock. Never spill liquid of any kind on
the product.
13. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks.
Refer all servicing to qualified service personnel.
Whe n to Ca ll Your Se rvic e Re p re se nta tive
WARNING: Do not attempt any maintenance or troubleshooting other than
that mentioned in this manual. This machine contains a laser
beam generator and direct exposure to laser beams can cause
permanent eye damage.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating instructions
are followed. Adjust only those controls that are covered by the
operating instructions since improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a
need for service.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Powe r a nd Ground ing
SAFETY
Powe r a nd Ground ing
Powe r Sup p ly
1. Power requirements: 220-240 V, 50/60 Hz (Only 50Hz is printed on the
rating plate of some machines.)
2. Insert the power plug securely into the wall socket.
3. Make sure that the wall outlet is near the machine and readily
accessible.
4. Do not connect other equipment to the same socket.
5. Do not step on or set anything on the power cord.
6. Do not connect other equipment to the same extension cord.
7. Be sure that the power cord is not in a position where it would trip
someone.
8. The wall outlet must be easily accessible.
Ground ing
Ground the machine and the lightning protection circuit in accordance with
regulations. Do not ground to gas or water pipes, or to a telephone ground
plug. Proper grounding is to the ground terminal of the power outlet. Be sure
that the ground terminal of the power outlet is properly grounded.
The lightning protection circuit for the machine requires the machine to be
properly grounded. If proper grounding is provided, about 90% of lightning
damage can be prevented. For safety, be sure to connect the machine to a
three-prong grounded outlet.
Cold We a the r Powe r-up
Avoid raising the room temperature abruptly when it is below 14°C, or
condensation may form inside the machine.
1. Raise the room temperature to 10°C at less than 20°C per hour.
2. Wait for 30 to 60 minutes.
3. Turn the power on.
4. Do not use the machine near a humidifier.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Thund e rstorm s
Thund e rstorm s
With proper grounding, about 90% of lightning damage can be prevented.
However, if possible, during severe electric storms turn the power switch off
and disconnect the power cord and telephone line cord.
GENERAL
1. Since some parts of the machine are supplied with high voltage, make
sure that you do not attempt any repairs or attempt to access any part of
the machine except those described in this manual.
2. Do not make modifications or replacements other than those mentioned
in this manual.
3. When not using the machine for a long period, disconnect the power
cord.
Ozone
The machine generates ozone during operation. Normally, the ozone level is
safe for operators. However, during a long copy run or while printing a long
message, ozone odor may appear; in such a case, ventilate the room.
Sym b ols & Conve ntions Use d In This Ma nua l
Documents: A document is anything you put on the feed table of your ma-
chine whether your are faxing it or copying it.
Prints:
A print is anything that comes out of the machine: a fax mes-
sage you received or a copy you made.
Procedures: Procedures are described step by step. Perform them in or-
der. When you see an LCD display, it always shows what
comes after performing the step it accompanies. Other illus-
trations accompanying steps help you find the right key or
handle, or show you how to perform the step.
This is a step in a procedure.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Ma c hine La yout
Op e ra tion p a ne l
1- The Receive File indicator lights when a fax
10- Press the Speed Dial key and enter a two digit code
(between 00 & 49) to dial or store individual
numbers (see page 21).
message is stored in memory (see page 14).
2- The Check Display indicator lights to tell you to
read the display.
11- The Pause/Redial key inserts a pause when you
are dialing or storing a fax number. Or, press the key
to redial the last number dialed. (The redial feature
doesn’t work once you’ve started dialing a new
number.)
3- Press the Auto Select key to use Auto Receive
Mode. The indicator lights when you are in this mode.
4- The resolution/Halftone is indicated by these three
indicators and can be changed by the
resolution/Halftone button.
12- Press the On Hook Dial key to dial a phone call
from the keypad without having to lift the phone or
handset off the hook (phone or handset option
needed).
5- When the Memory indicator is on, then memory
transmission is in effect, if it is off, immediate
transmission is in effect. Switch between the two
with the Memory button.
13- Press the Clear key to erase the last character or
digit entered, or use the left and right arrow keys to
move the cursor and then press Clear to erase
whatever is at the cursor.
6- There are ten Quick Dial keys. Use them to store
individual numbers (see page 21) or groups (see
page 23 ). Use the keys to enter characters (see
page 71). Use Quick Dial 09 as a dial option key .
Use Quick Dial 10 as a Group key (see page 25).
14- Press the Stop key to stop a transmission or a
document scanning, to stop a reception or to stop a
long copy run. The machine will finish printing out
the sheet being printed and then stop.
7- The Liquid Crystal Display guides you through tasks
and informs you of the state of the machine.
Messages appear here. The LCD consists of two
20-character lines.
15- Press the Start key to start all tasks.
16- Use the numeric keypad (sometimes called the 10
keys) to dial fax numbers, to enter the numbers of
copies, etc.
8- Use the arrow buttons to navigate through functions,
to accept or reject settings, or to set function options.
9- Press the Function key and enter a two digit code
to access functions 11 to 51. (For functions 61 to 94,
enter 6, the access code on page 64 and the
function number.)
Note: When you attach the sheet to the machine,
make sure the line above "Symbol" is aligned with
the arrow mark on the machine.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Pa rt Na m e s
5
4
3
6
2
1
9
7
8
10
1- The main switch turns your machine on and off.
9- When loading paper, match the paper guide to the
paper size.
2- 10 Quick Dial keys store telephone numbers.
10- The optional paper feed unit holds more paper.
3
The cover release button
4- Incoming faxes and copies are sent to the copy tray.
5- The automatic document feeder (ADF) holds up
to 30 sheets which are fed one at a time. Place your
original documents here.
6- Match the document guide to the size of your
original documents.
7- Scanned documents are stacked on the Document
Tray.
8- The main paper tray holds copy paper.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
If you have not yet installed your fax machine, do so now. See Installation, on
page 75.
This section covers what you’ll most often need to do:
Recommended Types of Document ................................................................. 4
Memory Transmission and Immediate Transmission........................................ 6
Receiving Calls & Fax Messages(Faxes/Phone Calls)..................................... 11
Printing a Message Received & Stored
(Substitute Reception) ...................................................................................... 14
Faxing a Page With Very Fine Detail................................................................. 15
Optional Feature for Transmission .................................................................... 16
Redialing ........................................................................................................... 19
Storing & Editing Fax Numbers (Functions 31 & 32)........................................ 21
Storing & Editing a Group of Fax Numbers (Function 33)................................ 23
Chain Dialing..................................................................................................... 27
Erasing a Stored Message Before It Is Sent
(Functions 21 & 22)........................................................................................... 28
Printing a Stored Message (Function 51)......................................................... 29
Polling Reception (Function 11)........................................................................ 30
Talking Before Sending a Fax(On Hook Dial) ................................................... 31
Sending a Fax using the Handset .................................................................... 31
A Fe w Hints...
Press Clear to erase the last letter or digit that you entered.
Press No to erase the entire name or number and start again.
To enter characters and labels, turn to page 71.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Re c om m e nd e d Typ e s of Doc um e nt
Re c om m e nd e d Typ e s of Doc um e nt
Before you send your document, make sure that it meets the following
requirements.
CAUTION: Documents that do not meet these requirements can cause your
machine to jam or may cause some components of the machine to become
damaged or dirty.
Minimum size
148mm
Maximum size
216mm
208mm
105mm
Scanning direction
600mm
Scanning direction
*The part shaded
maximum scanning width range.
will not be scanned, because it is outside the
Correct Size for the Auto Document Feeder
2
Thickness: 0.05 to 0.2mm (50 to 90g/m paper)
Length and Width: See the above diagram.
If the page is too short, put it inside a document carrier or enlarge it with a
copier.
If the page is too long, divide it into two or more sheets.
Clearly Written
Small faint characters may not be transmitted clearly.
Uniform Page Size
Do not use different sizes of document in the same transmission.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Re c om m e nd e d Typ e s of Doc um e nt
FAXING
Page Condition
Do not place damaged pages in the automatic document feeder.
❐ If your pages are curled or dog eared, flatten them.
❐ If your pages are stuck together, shuffle the stack.
❐ If your pages are folded, torn, or patched together, make copies.
❐ If your pages have binding hiles, trim the edges or make copies.
Originals that contain the following materials should not be placed in the
document feeder.
Note: Copies made with a copier that uses silicone oil may cause a misfeed.
To avoid this, do not scan such copies until five or ten minutes after
copying.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Me m ory Tra nsm ission a nd Im m e d ia te Tra nsm ission
Me m ory Tra nsm ission a nd Im m e d ia te Tra nsm ission
There are two ways to send a fax message.
❐ Immediate Transmission
❐ Memory Transmission
Im m e d ia te Tra nsm ission (Me m o ry ind ic a to r no t lit)
Immediate Transmission is convenient when:
❐ You wish to send a message immediately
❐ You wish to quickly check whether you have successfully connected with the
other party’s fax machine.
❐ Your machine’s memory is getting full
The machine dials immediately after you press Start (or at the specified later
time, if you used a time-delay feature like Send Later). The message is
scanned and transmitted page by page without being stored in memory.
Me m ory Tra nsm ission (Me m o ry ind ic a to r lit)
Memory Transmission is convenient because:
❐ Fax messages can be scanned much more quickly (you can take your document
away from the fax machine without waiting too long).
❐ While your fax message is being sent, another user can operate the machine
(people will not have to wait by the fax machine too long).
❐ You can send the same message to more than one place with the same
operation.
After you press Start, the machine doesn’t dial until all the pages of your fax
message have been stored in the memory.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Me m ory Tra nsm ission a nd Im m e d ia te Tra nsm ission
Me m ory Tra nsm ission
FAXING
Caution: If your document gets stuck while it is being processed, press the
Stop key, and turn to page 55 for instructions on how to safely re-
move the original.
Make sure that the machine is in
standby mode for faxing. The dis-
play should look like this:
1
Fan your document stack (at
most 30 pages: 80g/m ) to make
sure all pages are loose, then
square it.
2
2
All pages in your document must
be one-sided and be of the same
size.
Insert the document face up in
the feeder and adjust the guides
to fit the width of the document.
3
Note: You can dial before you set
the document. Place the docu-
ment after you dial the number
and go to step 7.
The display will look like this:
4
If the memory indicator is not lit,
press the Memory key.
5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Me m ory Tra nsm ission a nd Im m e d ia te Tra nsm ission
Dial the number in one of the fol-
lowing ways.
6
a) Ten Key Pad
b) Quick Dial
c) Speed Dial
d) Group
Example:
Example:
Speed Dial 10
Method 1 *
Quick Dial key 08.
Method 2 **
Quick Dial key 10
and 1 on the ten
key pad.
06
07
Speed Dial
1
0
If you install the handset, you can sent the message manually. Pick up
the handset and dial.
If you want to erase a digit of the phone number, press the Clear key.
If you want to erase the entire number, press the No key.
*: In this example Group Dial is programmed in Quick Dial 08.
**: In this example Quick Dial key 10 is programmed as the Group key, and
Group dial number 1 is programmed.
Programming Quick Dial: see page 21.
Programming Speed Dial: see page 21.
Programming Group Dial: see page 23.
Programming Group key: see page 25.
Note: The maximum destinations you can dial using the ten key pad is 49.
However, this limitation is also subject to memory capacity.
If you enter the wrong number,
press No or Clear and enter
again.
Press Clear to delete one digit.
Press No to delete the whole
number.
Press Yes to enter another num-
ber.
If you have only one destination,
7
press Start.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Me m ory Tra nsm ission a nd Im m e d ia te Tra nsm ission
FAXING
Repeat steps 6 and 7 until all destinations are entered.
8
The machine stores your message and dials the first number (or, if you
selected Send Later, it will return to standby mode and the fax message
will be sent at the time that you selected). Send later: see page 16 .
Press the Start key and wait. The
machine will dial the destination’s
number.
9
If you like to cancel the transmis-
sion, press the Stop key during
communication.
Then press Yes to cancel the
transmission.
If the other party’s line is busy,
your machine will dial again.
If the other party’s fax machine
answers, both machines will con-
nect and yours will send the mes-
sage.
Tip: If your line goes through a local switchboard (a PBX) remember to dial
the exit code. Press the Pause key immediately after the code. If the
number includes a country code, press the Pause key after the coun-
try code, then dial the rest of the number.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Me m ory Tra nsm ission a nd Im m e d ia te Tra nsm ission
Im m e d ia te Tra nsm ission
Make sure that the machine is in
standby mode. The display
should look like this:
1
The memory indicator should go
out. If the memory indicator is lit,
press the Memory key.
2
Place the entire document face
up into the feeder. (No more than
30 pages.)
3
How to set document see page 7.
Note: You can dial before you set
the document. Place the docu-
ment after you dial the number
and go to step 6.
Dial. (See page 8 for how to dial.)
4
Press the Start key
5
The machine dials and connect to the other party. The number that you
dialed and the other party’s RTI or CSI is displayed.
(RTI, CSI: see page 88.)
6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Re c e iving Ca lls & Fa x Me ssa g e s(Fa xe s/ Phone Ca lls)
FAXING
Re c e iving Ca lls & Fa x Me ssa g e s(Fa xe s/ Phone Ca lls)
Ove rvie w
The machine can treat incoming fax messages and telephone calls in three
ways.
❐ Auto mode (Auto Select Lit)
Use this mode if your line is shared by a fax machine and telephone.
When a call comes in, the machine will ring a number of times to give you the
chance to pick up the handset. If you do not pick up and the call is a fax
message, the machine will go into fax mode and start receiving. You can choose
the number of times the machine rings before taking the call by altering the Auto
Ring time (see page 13). Also use this mode if you have a telephone answering
machine connected (see page 13).
❐ Fax mode (Auto Select Lit)
Use this mode if you have a dedicated fax line.
The machine assumes all calls are fax messages. It will ring once to alert you to
an incoming call and then start receiving.
❐ Manual Receive Mode (Auto Select Not Lit)
Use this mode if your line is shared by a fax machine and a telephone but you
wish to answer all calls yourself and decide whether they are fax messages or
telephone calls. You must manually hit the Start key to receive a fax.
The machine will ring continuously until you answer the call, so you have to be
near the machine at all times.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Re c e iving Ca lls & Fa x Me ssa g e s(Fa xe s/ Phone Ca lls)
Auto Mo d e o r Fa x Mo d e (Auto Se le c t Lit)
When the Auto Select indicator is lit, the machine is in one of the automatic
reception modes ( Auto mode or Fax mode). Which mode is active depends on
how you set up your machine. Decide which mode you will use most often and
program it with the following procedure. Then press the Auto Select button
whenever you wish to switch to and from this mode.
Press the Function key and 6, 2,
2, 2, 2, 6, 2 using the ten key pad,
then press the Yes key.
1
Press the key until "
2
" appears.
Press the Yes key.
3
Select the setting you want using
the and the keys.
❐ Select "FAX": Auto Select indicator
shows you are in Fax mode.
4
❐ Select "AUTO": Auto Select indicator
shows you are in Auto Receive mode.
Press the Function key.
5
Ma nua l Re c e ive Mo d e (Auto Se le c t No t Lit)
This mode is active when the Auto Select indicator is NOT lit. Press the Auto
Select key to switch to and from this mode. You have to answer the call yourself
and decide whether it is a fax or a telephone call. The procedure for answering
a call is as follows:
Pick up the handset.
1
Listen to the other end.
2
❐ If you hear a voice, continue your conversation as you would normally.
❐ If you hear a fax tone, remove any documents from the feeder, press the
Start key then replace the handset. The machine will start receiving.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Re c e iving Ca lls & Fa x Me ssa g e s(Fa xe s/ Phone Ca lls)
FAXING
Se tting the Auto Ring Tim e
In Auto mode, the machine rings a number of times to give you the chance to
pick up the handset before taking the call automatically. You can alter the
number of rings by changing the Auto Ring Time.
Press the Function key and 6, 2,
2, 2, 2, 6, 1 using the ten key pad,
then press the Yes key.
1
Press the key until the opposite
display appears.
2
Press the Yes key. The factory
setting will be displayed, either:
❐ Change the number of rings, press the
No key, then press the new number us-
ing the ten key pad.
3
Example 03. Press 0, 3 using the ten
key pad.
❐ Keep these settings, go to step 4.
Press the Yes key, then the
Function key.
4
Whe n you c o nne c t Te le p ho ne Answe ring Ma c hine
When you are in Auto Mode, you can connect the Telephone Answering
Machine.
❐ Plug the answering machine into the TEL jack on your fax machine.
❐ Auto mode ensures that your answering machine has the chance to respond to
incoming telephone calls. If the call happens to be a fax message, the message
will be given to the fax machine automatically.
❐ When you connect the telephone answering machine, the Auto Ring Time must
be set to one ring more than the number of rings that your answering machine
waits before it takes the call. To check this number, have a friend call and do not
answer the phone, count the number of rings that you hear before the answering
machine takes the call.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Printing Re c e ive d Me ssa g e s tha t Ha ve b e e n Store d
(Sub stitute Re c e p tion)
Printing Re c e ive d Me ssa g e s tha t Ha ve b e e n Store d
(Sub stitute Re c e p tion)
If the Receive File indicator is lit, a message was stored in memory using
substitute reception. This could be because the machine ran out of paper or
toner, or because the night timer has turned off the print engine.
NightTimer: Hold any key to print messages received while the Night Timer
(page 43) has turned the heater off. Otherwise, check if any of
the following indicators are lit, and follow instructions.
When ADD PAPER appears in the display, your fax machine is out of
paper. Add paper: see page 48.
When ADD TONER appears in the display, your fax machine is out of
toner. Change the toner cassette: page 50.
-Message appears here-
Or There might be a paper jam (see
page 56) or an open cover.
As soon as the machine is back in working condition, messages stored in
memory will be printed. The Receive File indicator will turn off and the
messages will be erased from memory.
If a message comes in while you are copying, the fax machine will store the
message in memory and the Receive File indicator will light. The message will
be printed as soon as copying is done.
To turn substitute reception off or back on, set bit 0 of user parameter
switch 05. See page 66.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Fa xing a Pa g e With Ve ry Fine De ta il
FAXING
Fa xing a Pa g e With Ve ry Fine De ta il
So that text, diagrams and images stand out clearly in your document, the
machine automatically detects the image density (contrast) and makes a
compensation.
However, if you need to send a document which requires optimum clarity,
select the resolution setting appropriate to your needs.
You can select different settings for each page of your message. Simply
change the settings for page 2 while page 1 is being scanned.
Re solution & Sha d ing
The resolution button gives you control over document quality. The indicators
above the button show the current setting. Choose a setting that matches your
document.
Standard:
Standard quality. Use for most printed or typewritten docu-
ments. This is selected when the other resolution indicators
are not lit.
Detail:
Fine:
High quality. Use for documents with small print or fine de-
tails.
Very high quality. Use this for high quality reproduction.
Halftone:
Use this for optimum quality if your document contains
photographs/diagrams with complex shading patterns or gray
tones. If you choose this setting, resolution will automatically be
Detail.
Important: Faxing at a higher resolution requires more time. Frequent use of
high resolution could cause an increase in your phone bill, espe-
cially for long distance transmissions.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Op tiona l Fe a ture s for Tra nsm ission
Op tiona l Fe a ture s for Tra nsm ission
Se nd La te r
Using this feature, you can delay transmission of your fax message until a
specified time. This allows you to take advantage of off-peak telephone line
charges without having to be by the machine at the time.
CAUTION: If your machine’s memory is full, you will have to send the mes-
sage from the document feeder. This means that anybody remov-
ing your document would automatically cancel the operation.
Proceed as for a usual fax message but don’t press Start.
1
Press once and press Yes.
2
(
is also the Option key).
Enter a sending time that falls
within the following 24 hours.
For example: To send at 11:30,
press 1, 1, 3, and 0 from the key
pad. If you enter the wrong time,
press No and enter again.
3
Press Yes.
4
Use function 21 to erase a stored fax message before it is sent (see page 28).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Op tiona l Fe a ture s for Tra nsm ission
FAXING
Pa g e Count (Im m e d ia te Tra nsm ission only)
When your fax message is printed at the other end, page numbers will be
printed on the top of each page. Using the Page Count feature, you can select
the format in which the page numbers are printed.
If you use Page Count:
Page numbers will be printed in batch-numbering format (for example, p1/3,
p2/3, and p3/3 for a three-page message). This makes it easy for the other
party to see how many pages you sent, and if any are missing. However, you
have to input the number of pages at the keypad before sending.
If you do not use Page Count:
Page numbers will be printed only as a sequence (for example, p1, p2, p3).
This makes it difficult for the other party to tell at a glance whether any pages
are missing (for example, due to a double feed in your machine’s document
feeder).
Note:If you do not select Immediate Transmission, Page Count is automat-
ically switched on, and the pages are counted automatically.
If the numbering with page count appears strange, check that the page
count value matches the number of pages in your document.
Press until the right display ap-
pears.
1
Yes.
2
Example: 10 pages
1 0
3
Yes.
4
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
TTI
Op tiona l Fe a ture s for Tra nsm ission
Normally, the TTI programmed in your machine is printed at the top of each of
the pages you transmit when they are received at the other end. The top of the
image will be overprinted if there is no margin at the top of the transmitted
page.
In some cases, you may wish the other party to receive an unmarked copy of
your original. In this case, you can switch TTI off.
Press until the right display ap-
pears.
1
Press Yes.
2
If you wish to change the TTI set-
ting, press or until the dis-
played setting is correct.
3
Press Yes when you have fin-
ished.
4
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Re d ia ling
FAXING
Re d ia ling
If a message was not transmitted successfully, that does not mean that you
have to enter the telephone number again. In many cases, the machine will
redial the destination automatically. Or, with the Redial key, you can redial with
just a few keystrokes.
Autom a tic Re d ia ling
The machine will automatically redial the other party if any of the following
conditions occurred.
❐ The other party was busy
❐ There was no reply from the other party
❐ The message was rejected by the machine at the other end because of
excessive errors (in this case, redialing will only take place if Memory
Transmission was used)
The number of redials and the redial interval may be adjusted by a service
technician.
During redialing, the number being dialed is displayed as shown on the below.
Using the Re d ia l Ke y
The machine remembers the last telephone number that you input. If you have
to redial this number, just press the Redial key, then press the Start key.
This feature has the following uses.
If the machine is waiting to redial the other party, you do not have to wait for the
redialing interval to expire.
If you wish to send another message to the same address that you just sent
last time, you don’t have to dial the full number again.
Place the message in the feeder, then press the Redial key, then press the
Start key.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Re d ia ling
To send a fax using Redial, do the following:
Make sure that the machine is in
1
standby mode for faxing. The dis-
play should look like this:
Set your document. How to set
the document, see page 7.
2
Press Redial.
3
Press Start.
4
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing & Ed iting Fa x Num b e rs (Func tions 31 & 32)
FAXING
Storing & Ed iting Fa x Num b e rs (Func tions 31 & 32)
Numbers that you often use can be stored in memory. A stored number will
remain in memory even if the power is cut.
You can store numbers in three ways.
Quick Dials
The number is assigned to its own key. To dial that number, just press the key.
You can store up to 10 numbers in this way.
Speed Dials
The number is given a two digit code. To dial the number, press the Speed Dial
key and enter the code. There are 50 Speed Dial codes available numbered 00
to 49.
Groups
If you regularly broadcast messages to the same set of destinations, you can
combine these numbers into a group. Then just select the group and each
number will be dialled in sequence automatically. You can program up to 3
groups with 30 numbers each.
Storing , Ed iting a nd Era sing Quic k Dia ls/ Sp e e d Dia ls
These steps describe how to store or edit telephone number in Quick Dial
keys or Speed Dial codes. You can get a printout of numbers stored. In this
example we will store a new number in Speed Dial 01.
Choose Quick Dial or Speed Dial
programming mode.
❐ Quick Dial: Function 31 Yes
1
❐ Speed Dial: Function 3 2 Yes
Select the Quick Dial key or
Speed Dial code you want either:
❐ Quick Dial: Press the Quick Dial key
2
21
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Storing & Ed iting Fa x Num b e rs (Func tions 31 & 32)
❐ Speed Dial: Input a two digit Speed Dial
code.
e.g. Speed Dial 01: Press 0 1.
❐ If the Speed dial code you select is al-
ready used, press until an open code
appears.
❐ Press then Start to print a list of num-
bers.
Press Yes to accept.
3
4
Enter a new number or edit the
existing number.
To erase an existing number,
press No then Yes and go to step
9.
Press Yes to accept.
5
6
If you wish you can give this num-
ber a name:
❐ Edit the name: Press Yes and go to step
7.
❐ Skip naming: Press No and go to step 9.
Enter or edit the name. (See
page 71).
7
8
9
Press Yes to accept.
❐ Edit another number: Go to step 2
❐ Return to standby mode:
Press Function.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing & Ed iting a Group of Fa x Num b e rs (Func tion 33)
FAXING
Storing & Ed iting a Group of Fa x Num b e rs (Func tion 33)
This section describes how to program or edit a Group. You can also get a
printout of numbers that are already stored. In this example we will program
Group 1 into Quick Dial key 01.
You can store up to three groups numbered 1 to 3.
You can program up to 30 numbers in a Group.
Press Function, 3, 3, Yes .
1
Either:
2
❐ Enter the number of the group you want
to program or edit.
e.g. Group 1: Press 1.
❐ To print a list, press then Start.
Press Yes to accept.
3
4
You have two options:
❐ Edit or program the Quick Dial key for
this group: Press Yes and go to step 5.
❐ Skip the Quick Dial: Press No and go to
step 6.
Then either:
5
❐ Program a new Quick Dial: Press the
Quick Dial key you wish to use for this
group then Yes.
❐ Free up the old Quick Dial: Press No,
then Yes.
If a message like "USED AS.." flashes up, the key is already in use.
Press a different key.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Storing & Ed iting a Group of Fa x Num b e rs (Func tion 33)
If you wish you can give this
group a name:
6
❐ Edit the name: Press Yes and go to step
7.
❐ Skip naming: Press No and go to step 8.
Enter or edit the name then press
Yes.
7
8
Enter a fax number in one of
these ways:
❐ Press a Quick Dial key.
❐ Press the Speed Dial key followed by
two digits.
❐ Enter a number on the keypad.
Press Yes to accept.
9
If ALREADY PROGRAMMED
briefly flashes up on the display,
either:
❐ Press No to keep the number and
choose another number .
❐ Press Yes to erase this number from
the group.
You have two options:
❐ Enter another number: Go back to step
8.
❐ Finish entering numbers in this group:
Press No and go to step 11.
A
B
You may then either:
❐ Work on another group: Go to step 2.
❐ Finish: Press Function.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Era sing Group s
FAXING
Era sing Group s
These steps describe how to erase single numbers from a group.
Press the Function key and 3, 3
using the ten keypad, then press
the Yes key.
1
Enter the group number using the
ten key pad, then press the Yes
key.
2
Press the No key.
3
Press the No key.
4
Press the Yes key.
5
Press the Function key and 3, 3
using the ten keypad, then press
the Yes
6
❐ Delete another number: Go to step 2
❐ Finish: Press Function.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Prog ra m m ing the Group Ke y
Prog ra m m ing the Group Ke y
You can program the 3 groups. However, if there is no room in Quick Dial keys,
this group key is helpful. You have to program the 10 of the Quick Dial key as
the group key. How to transmit using the group key, see page 8.
Press Function 3 1 and Yes.
1
Press the Quick Dial 10.
2
Press Yes.
3
Press Yes.
4
Press Function.
5
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Prog ra m m ing the Dia l Op tion Ke y
FAXING
Prog ra m m ing the Dia l Op tion Ke y
This function of this key depends on the capabilities of the other terminal.
Press Function 3 1 and Yes.
1
Press the Quick Dial 09.
2
Press Yes.
3
Press Yes.
4
Press Function.
5
Dia lling with the Dia l Op tion Ke y.
Set the Document
1
Enter the number
2
Press 09 and Yes.
3
Enter the password
4
Press 09 and Yes.
5
Enter the subaddress
6
Press 09 to enter a space.
7
Note: You can program the password and sub-address in a Quick Dial, Speed
Dial or Group.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Cha in Dia ling
Cha in Dia ling
This feature allows you to compose a telephone number from various parts,
some of which may be stored as Quick Dial Keys or Speed Dial Codes, and
some of which may be input at the keypad.
For example, you can program commonly used area or country codes into
Speed Dial Codes or Quick Dial Keys.
Example: 01133-1-5553333 (From the USA to Paris).
Assume that the following Quick Dial and Speed Dial numbers have already
been programmed.
❐ Quick Dial 01 = 01133 (Overseas to France)
❐ Quick Dial 02 = 1 (Paris)
❐ Speed Dial 10 = 555
The machine ask you to dial
On Hook Dial or Handset Mode:
Press 01, 02, Speed Dial, 1, 0, then 3, 3, 3, 3.
Other:
Press 01, Pause, 02, Pause, Speed Dial, 1, 0, then 3, 3, 3, 3.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Era sing a Store d Me ssa g e Be fore It Is Se nt
(Func tions 21 & 22)
FAXING
Era sing a Store d Me ssa g e Be fore It Is Se nt
(Func tions 21 & 22)
Every time you store a fax message in your machine’s memory, a new file is
created. A file is also created for storing instructions to pick up a fax message
left elsewhere (polling, page 30). Each file is given a number. This number
appears on the memory storage report, Journal and Transmission Result
Report. To see which files are currently in memory, you may print a file list.
To erase a fax message stored in
memory:
Press Function, 2, 1, and Yes
1
To erase instructions to pick up a
message (polling):
Or
Press Function, 2, 2, and Yes
Press to scroll through the files.
You’ll get this.
2
- number or label-
Or: Press to obtain a list of all the files and their number. If you already
know the number of the file to erase, enter it directly from the keypad
and skip to step 4.
Scroll through the files with or .
3
- number or label-
Press Yes.
4
Press Yes again to erase the file.
5
6
Either:
❐ To erase another file, go to step 2.
❐ To finish, press Function.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Printing a Store d Me ssa g e (Func tion 51)
Printing a Store d Me ssa g e (Func tion 51)
If you need to see the contents of any of the files, use this feature.
Press Function, 5, 1, and Yes.
1
Press to scroll through the mes-
sages. You’ll see this.
2
-number or label-
Or: Press to obtain a list of all the files and their number. If you already
know the number of the file to print, enter it directly from the keypad and
skip to step 4.
Scroll through the message files
with or .
3
-number or label-
Press Yes.
4
-number or label-
Press Start to print the message.
5
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling Re c e p tion (Func tion 11)
FAXING
Polling Re c e p tion (Func tion 11)
Use this feature when you wish to pick up a message from another terminal.
Press Function, 1 and 1
1
Press Yes.
2
Dial the number from where you
will pick up the message.
3
-number or label-
You can use Quick Dial keys or
Speed Dial codes.
Press Yes.
4
-number or label-
.Press Start.
5
Note: Another terminal should have the polling feature. You cannot poll
from a machine that has set secure polling with ID number. Ask the
other end to make a polling file without polling ID.
De le ting a Pre se t Polling Re c e p tion (Func tion 22)
Use function 22. For details, see Erasing a Stored Message on page 28.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
FAXING
Ta lking Be fore Se nd ing a Fa x(On Hook Dia l)
Ta lking Be fore Se nd ing a Fa x(On Hook Dia l)
Press the On Hook Dial key.
1
Proceed as for a usual fax message but don’t press Start. (Do not use
the handset).
2
If you hear a voice from the machine’s built-in speaker, pick up the
handset and speak to the other party.
3
If you hear a high-pitched tone instead of a voice, place your fax
message in the auto document feeder, then press Start.
When you are ready to send your fax message, place your message in
the feeder, then ask the other party to press Start.
4
When you hear a high-pitched tone, press Start.
5
Replace the handset.
6
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Se nd ing a Fa x using the Ha nd se t
FAXING
Se nd ing a Fa x using the Ha nd se t
You can send a fax message using the handset. (External Telephone is
required.)
Set the document then pick up the handset.
1
Dial the other party.
2
If you hear a voice, speak to the other party.
3
If you hear a high-pitched tone instead of a voice, press Start.
When you are ready to send your fax message, ask the other party to
press Start.
4
When you hear a high-pitched tone, press Start.
5
Replace the handset.
6
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Ve rifying Com munic a tions, Errors, Counte rs, e tc .
OTHER FEATURES
Other features are listed here that you might find useful but that you will not set
very often.
Verifying Communications, Errors, Counters, etc..............................................
Rejecting Messages From Certain Senders .....................................................37
Saving Energy .................................................................................................42
Printing the Sender’s Identification....................................................................46
Tonal Signals .....................................................................................................46
Copying..............................................................................................................47
Ve rifying Com munic a tions, Errors, Counte rs, e tc .
You can obtain reports from your machine either by having your machine print
them out automatically, or by printing them out yourself.
Autom a tic a lly Printe d Re p orts
Unless otherwise indicated, the automatic printing of these reports can be
turned on or off by changing the bit of the user parameters (see page 64).
Jo urna l (Switc h 03, b it 7)
This report gives details on each communication made by your terminal. It is
automatically output after 35 transmissions and receptions.
File Re se rve Re p o rt (Me m o ry Sto ra g e Re p o rt) (Switc h 03, b it 2)
If you switch this report on, it is printed immediately after you store a document
in memory for Memory Transmission. It gives the file number, the time that it
was stored, and the destinations (including any Group numbers that were
selected).
Powe r Fa ilure Re p o rt (Sta ys o n)
This report is printed if the machine’s power was off for long enough to erase
files from the memory. The report gives details of the files that were lost. With
this information, you may store messages for transmission again, and contact
the senders of any received messages that were lost.
(Note: Phone numbers stored in Quick/Speed/Groups are not lost.)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Ve rifying Com munic a tions, Errors, Counte rs, e tc .
OTHER FEATURES
Co m munic a tio n Re sult Re p o rt (Me m o ry Tra nsm issio n) (Switc h 03, b it 0)
This report is printed out after memory transmission showing whether it was
successful or not. If you have switched this report off, a Communication Failure
Report will be printed only when a communication fails.
Transmission Result Report (Switch 03, bit 5)
This report is printed out after immediate transmission showing whether it was
successful or not.
Communication Result Report (Polling result report) (Switch 03, bit 4)
This report is printed after your machine polls a message from another
machine.
Co m munic a tio n Fa ilure Re p o rt (ON if Tra nsm issio n Re sult Re p o rt is OFF)
This report is printed if a memory transmission failure occurred, after a job is
completed. It is only printed if the Transmission Result Report is switched off,
and event of a communication failure.
Erro r Re p o rt (Turne d o n/ o ff b y a Se rvic e Te c hnic ia n)
This report is printed after each unsuccessful communication. The
communication failure report (above) is printed after a job has been completed.
So while doing a broadcast, the machine may print a number of error reports,
and at the end, it prints a communication failure or transmission result report.
Check it, and retransmit any pages that were not sent. If a particular problem
continues or gets worse, keep the error reports for the service technician.
Printing Pa rt o f the Im a g e o n the Re p o rt (Switc h 04, b it 7)
For reference purposes, the machine prints the first few inches of the fax
message on the following reports.
❐ Transmission Result Report
❐ Memory Storage Report
❐ Communication Failure Report
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Re p ort Form a ts
Ve rifying Com munic a tions, Errors, Counte rs, e tc .
Exa m p le 1. Erro r Re p o rt*
* * * ERROR REPORT (AUG 01 1995 -06:00 ) * * *
TTI XYZ COMPANY
TIME PAGE
FILE
ADDRESS
MODE
RESULT
--------------------------------------------------------------------
Report details appear here
Exa m p le 2. Jo urna l*
* * * JOURNAL (AUG 01 1995 07:00) * * *
TTI
XYZ COMPANY
<TX>
DATE TIME
ADDRESS
MODE
TIME
PAGE RESULT
FILE
--------------------------------------------------------------------
Transmission details appear here
<RX>
DATE TIME
ADDRESS
MODE
TIME
PAGE RESULT
FILE
-------------------------------------------------------------------
Reception details appear here
The Mo d e C o lum n
See the bottom of the Journal for a full listing of symbols on the Journal. On
other reports a code is given, informing the type of communication. These
codes are explained below.
The Re sult Co lum n
OK: Successful communication
E: An error occurred
The Fo o tno te o n the Jo urna l
TX counter: Total number of transmitted pages
RX counter: Total number of received pages
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Ve rifying Com munic a tions, Errors, Counte rs, e tc .
Re p orts You Ca n Printout Yourse lf
OTHER FEATURES
You can print these reports at any time by following the steps below.
Journa l (Func tio n 41)
In addition to the automatic output of this report, which we’ve described earlier,
you can print the Journal at any time.
Press Function, 4, 1 and Yes.
1
Press Start to print out the report.
2
File List (Func tio n 42)
This is a list of memory transmission files still in memory. It gives information
about each stored file, such as the fax numbers, start time, and status.
Press Function, 4, 2 and Yes.
1
Press Start to print out the report.
2
35
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Ve rifying Com munic a tions, Errors, Counte rs, e tc .
Te le p ho ne Num b e r List (Func tio n 43)
You can obtain a list of all the phone numbers stored in the machine. (You can
also obtain a list of stored numbers as you edit them. See the section on storing
numbers, beginning on page 21.
Press Function, 4, and 3.
1
Press Yes.
2
To print all the numbers (Quick Dial, Speed Dial, and Group numbers)
press Start. Then press Function and skip the following steps. Three
lists will come out.
3
Or Press No and you’ll see this:
Either:
4
If you want a Quick Dial list, press
Yes.
If you don’t press No.
Either:
5
If you want a Speed Dial list,
press Yes.
If you don’t press No.
Either:
6
If you want a Group list, press
Yes.
If you don’t press No.
Press Start.
-Message appears here -
7
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Re je c ting Me ssa g e s From Ce rta in Se nd e rs
Counte rs (Func tion 94)
OTHER FEATURES
These counters will help you if you wish to keep a regular check on how many pages your machine
has sent, received, and copied. The machine has the following counters:
TX Counter:
RX Counter:
The number of pages that your machine has sent (transmitted)
The number of pages that your machine has received
Scan Counter: The number of pages that your machine has scanned (including copies)
Print Counter: The number of pages that your machine has printed
(including copies,reports and lists.)
Press Function, 6 , and enter the
access code 2222, then press 9,
4, and Yes.
1
Press Yes to check the SCAN
and PRINT counter.
2
Either:
❐ To finish, press Yes twice.
3
❐ 1) If you have replaced the photoconductor
before REPLACE OPC appears (see page
53) then press Yes to reset the counter.
2) Press Clear.
3) Press Yes.
When you have finished, press Function.
4
Re je c ting Me ssa g e s From Ce rta in Se nd e rs
Re je c ting Me ssa g e s From Se nd e rs Who Don’t Id e ntify The m se lve s
Your fax machine can reject incoming messages lacking an identifier signal. Follow the user
parameter procedure on page 64 to enter these settings.
Switch 05, bit 1 - 0: Accept such messages, 1: Reject such messages
Re je c ting or Ac c e p ting Me ssa g e s from Sp e c ifie d Se nd e rs
This feature is called Authorized Reception. It helps you reject junk fax mail.
It lets you specify which terminals you wish to receive fax messages from; all others will be shut
out.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Re je c ting Me ssa g e s From Ce rta in Se nd e rs
1 - You must specify a list of senders (function 81). See page 39.
2 - You must turn Authorized Reception on (function 62). See page 41.
3 - You must set your machine to accept or reject messages from senders
in that list (user parameters, switch 08, bit 2 and 3; see page 41).
If you accept them, the general public will not have access to your fax machine.
You accept messages only from a group of people you know.
If you reject them, everyone will be able to send you messages except the
people in the list. This is useful to reject the junk fax mail.
You can store up to 30 identifications with this feature. You can program part of
an identification and accept (or reject) messages from all senders whose
identification contains that part. See Wild Cards, page 95.
List of the
Authorized
Senders
Authorized
Reception on/off messages from
(Function 62)
Accept
Result
special
terminals listed
or not listed
(Function 63)
Either
(Function 81)
Empty
On
No messages
are accepted.
Empty/Not
empty
Off
On
Either
Listed
All messages
are accepted.
Not empty
Only messages
from special
terminals are
accepted.
Not empty
On
non-listed
All messages
are accepted
except from
special
terminals.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Re je c ting Me ssa g e s From Ce rta in Se nd e rs
OTHER FEATURES
Cre a ting & Ed iting the List of Authorize d Se nd e rs (Func tion 81)
Cre a ting the List o f Autho rize d Se nd e rs
Press Function, 6 and enter the
access code 2 2 2 2. Then, press
8, 1, and Yes.
1
(At this time, you can print an
Authorized Reception List by
pressing and Start if it has al-
ready been created.)
Press Yes again.
2
Enter the sender’s RTI or CSI.
For example, enter "XYZ COM-
PANY".
3
How to enter characters, see
page 71.
Press Yes.
4
To store this as a wild card, (see
glossary) press Yes, otherwise
press No. The word
will appear briefly. And
you’ll see:
5
Go back to step 3 to enter another RTI or CSI or press Function if you
are done.
6
39
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Re je c ting Me ssa g e s From Ce rta in Se nd e rs
Ed iting the Autho rize d Se nd e rs
Press Function, 6 and enter the
access code 2 2 2 2. Then, press
8, 1, and Yes.
1
Press to scroll the RTI/CSI.
When the RTI/CSI you want to de-
lete appears, press Yes.
2
Edit the RTI/CSI of the special ter-
minal.
and to move the cursor.
3
Clear to delete one character.
No to delete the whole characters.
How to enter characters: p 71.
Press Yes.
4
To store this as a wild card, (see
glossary) press Yes, otherwise
press No. The word
5
will appear briefly.
Press Yes and Function.
6
Era sing the Autho rize d Se nd e rs
Press Function, 6 and enter the
access code 2 2 2 2. Then, press
8, 1, and Yes.
1
Press to scroll the RTI/CSI.
And the RTI/CSI you want to de-
lete appears, press Yes.
2
Press No and Yes.
3
Press Function.
4
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Re je c ting Me ssa g e s From Ce rta in Se nd e rs
OTHER FEATURES
Switc hing Authorize d Re c e p tion On or Off (Func tion 62)
Before you use Authorized Reception, you have to switch the feature on.
Press Function, 6 and enter the
access code 2 2 2 2. Then, press
6, 2, and Yes.
1
Press until the screen is as
shown at right.
2
Press Yes.
3
Press or to change the on or off setting.
4
Press Yes and Function.
5
Ac c e p ting or Re je c ting Me ssa g e s From Se nd e rs in the List
You can choose to accept or reject messages from senders in the list. Follow
the user parameter procedure on page 64 to enter the following settings.
Switch 08, bit 2
You have to set it "1"
Switch 08, bit 3
0: Accept calls from senders in the list of authorized senders.
1: Reject calls from senders in the list of authorized senders.
Hints for Using Authorize d Re c e p tion
You must specify the sender’s identification code (their CSI or RTI, see page
87) which could be a little different from their phone number.
To get the other party’s identification, call and ask for their CSI or RTI code.
Explain that you need the number programmed into their fax machine for
identification purposes. Or, attempt a communication with their fax machine
and print out a transaction confirmation report (function 41, see page 34). Read
the identification under the RTI or CSI heading of the report.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Sa ving Ene rg y
Sa ving Ene rg y
To print a fax message your fax machine uses a heating roller to fuse the image
to the paper. This roller must already be hot when the paper passes under it. To
maintain a temperature high enough to permit proper fusing, electricity is
consumed. This facsimile is equipped with various energy saving modes to
reduce the consumption of electricity while the machine is waiting for a fax
message.
Letting the heating roller cool to room temperature will reduce the amount of
electricity the fax machine consumes. However, the fax machine will not print
incoming messages right away, it will store them in memory and print them out
after the roller warms up.
Letting the heating roller cool halfway reduces the amount of electricity the fax
machine consumes, but not as much as letting it cool to room temperature. On
the other hand, since warming up takes only a short time, incoming fax
messages can be printed right away.
If your fax machine enters saving energy mode, SAVING ENERGY appears on
the display.
The saving energy mode is related to the Night Timer. Refer to the section titled
"Night Timer".
How to sta rt the sa ving e ne rg y m od e
Your machine will enter the saving energy mode when machine is not used for
5 minutes.
If you want to change the five minute period to one or three minutes, or if you
do not want your machine to enter the saving energy mode automatically,
please contact your service representative.
How to e xit the sa ving e ne rg y m od e
Your machine exits from the energy saving mode.
❐ When a fax is received. (If the night timer is on, the message will printed out after
the night timer ends.)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa ving Ene rg y
OTHER FEATURES
You can still send a fax while the machine is in saving energy mode.
You can also carry out some functions (e.g. programming) by first holding down
a key to switch to standby mode.
Whic h sa ving e ne rg y m o d e is b e st fo r yo u?
You have two choices: You can let the roller cool to room temperature or you
can let it cool to the midpoint. To choose which of the two settings you would
prefer, set the user parameter switch.
When you allow the roller to cool to room temperature, energy savings are at a
maximum and printing will take a little longer since the roller will take more time
to come to printing temperature. When you select the midpoint, some energy
savings will still be achieved and printing will occur more rapidly.
Switch 05 bits 6 & 7
Letting the heating roller cool to room temperature: Bit 6 at 0, Bit 7 at 0
Letting the heating roller cool halfway: Bit 6 at 1, Bit 7 at 0
Saving Energy with the Night Timer
You can set sleep time to let the machine go to saving energy condition and set
the wake up time when it returns to standby mode the next morning. During this
Night Timer mode, a fax message received is stored in the memory and will be
printed automatically the next morning after the wake up timer is activated.
As a typical example, you could program the heating element inside the printer
to stay off at night and over the weekend. (You can program different settings
for every day of the week.)
To use the Night Timer, you must:
1. Program the timers for each day of the week.
2. Switch the Night Timer feature on.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Sa ving Ene rg y
Se tting the Tim e r (Func tio n 71)
Caution: While the night timer is active, all incoming calls are refused if the
memory fills up.
Example: For Tuesday, set the Night Timer to switch the heater on at 9 am and
off at 6 pm.
Press Function, 6 and enter ac-
cess code 2 2 2 2. Then, press
7,1 and Yes.
1
Press Yes.
2
Use the and keys to scroll
through the days of the week.
Example: Press twice to go to
Tuesday.
3
Press Yes.
∗
4
5
There are two timers for each day, each with an ON/OFF setting. "ON"
means that the heater will switch on at the time indicated. "OFF" means
that the heater will switch off at the time indicated. To change the ON to
OFF, or the other way round, press ∗ or #. When the ON/OFF display is
correct: Go to step 6.
Press to move the cursor under
the time.
6
7
Input the time(9:00): Press 0, 9,
0, and 0 from the key pad.
∗
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa ving Ene rg y
OTHER FEATURES
Press Yes.
∗
8
SRepeat step 5 to 7 for the second timer (18:00)
9
Tip: If you want the heater on all day, set both timers to ON = 00:00.
If you want the heater off all day, set both timers to OFF = 00:00.
Either press Yes and Function to finish, or go back to step 3 to program
the timer for another day.
A
Switc hing the Nig ht Tim e r On o r Off (Func tio n 62)
The Night Timer feature must be switched on using Function 62.
Press Function, 6 and enter ac-
1
cess code 2 2 2 2 . Then, press 6,
2 and Yes.
Scroll through the list of features
with until the screen is as
shown opposite.
2
Press Yes.
3
Change the on/off setting by
pressing or .
4
Finish: Yes and Function.
5
45
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FEATURES
Printing the Se nd e r’s Id e ntific a tion
Printing the Se nd e r’s Id e ntific a tion
This feature prints at the top of the message, the sender’s identification (the
CSI or RTI, see page 95) that appears on the display.
Tona l Sig na ls
On this model the key on the ten keypad is used as the Tone key. Some
organizations offer you a special service by telephone, which you can access
by transmitting Touch tone or DTMF tones. If your phone service provides only
pulse dialing, or if you are calling over a digital network, the ability to generate
Tonal Signals will allow you to access these services. First, dial the other party
When you are through to the other end, press the Tone key and enter the code
number that is needed to access the required feature at the other terminal. You
do not need to press the Tone key if your machine is set up for dialing in Tone
Dial (DTMF) mode.
Using the Tone Ke y
Make sure that the machine is in standby mode, and that there is no
document in the feeder.
1
Pick up the telephone handset, or press the On Hook Dial key.
2
Dial the remote facility. Do not press the Start key.
3
After your line is connected to the remote facility, do the following:
4
❐ If your telephone line type is DTMF (Tone Dial): Go to step 5.
❐ If your telephone line type is Pulse Dial: Press the on the ten keypad. A dot
appears in the display.
Input the digits that you need to use the remote facility. After you have
finished your business with the remote facility, hang up.
Note: Do not press the Start key.
5
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying
OTHER FEATURES
Copying
If you need to make a copy of something, and there is no copier available, use
your fax machine. Just place your original in the feeder, and press the Copy
key.
Note: When copying, the resolution is fixed as Detail.
Place your original in the feeder
1
Press Copy.
2
If you have the optional lower cas-
sette, you can select the paper
size by pressing .
3
LT=letter LG=legal
The opposite display shows that
you select the Legal size.
Input the number of copies that
you need.
Example: 3 copies, press 3 of the
4
ten key pad.
Note: This machine makes copies in the order P1, P1, P2, P2 (for
example when making 2 copies of a 2 page document).
Press Start.
5
47
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTAINING YOUR MACHINE Loa d ing Pa p e r in the Ma in Pa p e r Tra y
MAINTAINING YOUR MACHINE
Loa d ing Pa p e r in the Ma in Pa p e r Tra y
Caution: Make sure the paper conforms to the specifications on page 72.
Note: If any foreign matter (especially glue) is on the copy paper, print quality
may deteriorate. Make sure the front, back and sides of the copy paper are
completely clean.
Place the paper on the tray, mak-
ing sure it is flush against the rear
and left walls.
1
Slide the paper guide to the left
so it lightly touches the paper.
2
Note: Whenever you change the paper size, set the paper size by Function 34
(see page 82).
Stora g e Cond ition of the Copy Pa p e r
2
❐ 60 to 90 g/m . copy paper is recommended: A4 is the most common.
❐ Do not use damp paper or copies will be defective.
❐ Do not touch copy paper if your fingers are wet or oily; fingerprints may
appear on the copy.
❐ Keep paper in a vinyl bag if it will not be used for a long time.
❐ Store in a cool dry place.
❐ Store flat. Do not stand upright.
❐ The following materials cannot be used in the paper cassettes : Post
cards, tracing paper, OHP sheets, adhesive labels
❐ Do not overload the paper trays.
❐ If multi-sheet feeding occurs or dog-eared copies are made when using
recycled paper in the paper cassette, fan the recycled paper and load it
in the paper cassette again.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Re p la c ing Tone r Ca sse tte
MAINTAINING YOUR MACHINE
Re p la c ing Tone r Ca sse tte
When the Check Display indicator starts to blink and TONER LOW appears in
the display, the toner cassette is almost empty. You will be able to make roughly
100 more copies before you have to replace it with a new cassette. When ADD
TONER appears in the display, it is time to install a new toner cassette.
WARNING:
Do not incinerate waste toner or depleted cassettes. Toner
dust might ignite suddenly if exposed to flames.
Lift the toner cartridge by the handle top.
Do not touch any parts other than those specified in the
procedure.
Caution:
Caution:
Squeeze in the release button on
the left of the machine and open
the cover.
1
2
Lift out the old toner cassette .
Shake the new toner cassette
from side to side before installing
it.
3
4
Put in the new toner cassette.
Make sure it drops in smoothly
and easily.
Close the cover firmly and pull
the copy output tray forward.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTAINING YOUR MACHINE
Re p la c ing Tone r Ca sse tte
Stora g e Cond ition of the Tone r Ca sse tte s
❐ Store in a cool, dark place.
❐ Never store where they may be exposed to heat.
❐ Keep out of the reach of children.
❐ Do not eat toner.
❐ Do not lay heavy objects on toner cassettes.
❐ Do not incinerate toner or toner containers. Toner dust may cause flash-
back when exposed to an open flame.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Re p la c ing the Photoc ond uc tor
MAINTAINING YOUR MACHINE
Re p la c ing the Photoc ond uc tor
The photoconductor receives the print image before it is transferred to paper.
To ensure optimal quality, replace it every 20,000 copies.
If the following display appears, it is time to replace the photoconductor.
To check how many sheets you’ve printed, please refer the section titled
"Counters" (See page 37.)
Caution: Do not expose the photoconductor drum to light for an extended
period.
Caution: Do not open the cover or touch the PC drum : it cannot be re-
paired. Any scratch on the drum would be reproduced on prints.
Caution: Do not touch any parts other than those specified in the proce-
dure.
Caution: Though organic photoconductor drums are safe for the environ-
ment, dispose of used drums according to local regulations.
Squeeze in the release button on
the left of the machine and open
the cover fully back.
1
Lift out the toner cassette.
2
Remove the old photoconductor.
3
51
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTAINING YOUR MACHINE
Re p la c ing the Photoc ond uc tor
Unpack the new photoconductor
and put it into the machine.
The left and right ends are
4
marked "L" and "R" respectively.
Reinstall the toner cassette.
5
Close the cover firmly and pull
the copy tray forward.
6
Caution: Do not expose the new drum to light for an extended period of time.
Do not touch the surface of the drum.
After you replace the photoconductor, reset the counter for photoconductor
inside the machine. If you have replaced the photoconductor before RELACE
OPC appears, see page 37 for how to reset the OPC counter (Function 94).
The display should be as oppo-
site.
7
Press
.
8
9
Press Yes.
The counter resets.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Da ily Ma inte na nc e
MAINTAINING YOUR MACHINE
Da ily Ma inte na nc e
Caution: When wiping or cleaning components, do not use any sort of
cleaning agent or abrasive powder. Use a damp soft cloth to
clean and a dry soft cloth to wipe dry.
Cle a ning the rolle rs
Grasp the center of the operation
panel and pull forward to open it.
Note: It is a good idea to steady
1
[A]
[B]
the machine.
[C]
While holding the panel open, wipe the two center rollers [A] and [B] with
a damp cloth.
To clean the hidden part of the white roller repeat the next 3 steps 5
more times.
2
1) Close the panel. The roller rotates automatically by about 60 °degrees
2) Open the panel and wipe the rollers.
Clean the exposure glass. [C]
Close the panel firmly and pull
the copy output tray forward.
3
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Troub le shooting
If a n Ind ic a tor Lig hts Up on the Op e ra tion Pa ne l
Trouble shooting
Caution: Do not attempt to make any repairs other than those described in
this manual. Removing covers may expose you to dangerous volt-
ages and other risks. Refer all servicing to qualified personnel.
Check the description in the display.
If a n Ind ic a tor Lig hts Up on the Op e ra tion Pa ne l
If COMM. ERROR PRESS STOP KEY appears in the display:
Press Stop.
The Receive File indicator is lit: You’ve received a fax message which is now
stored in the machine. See page 14 for instructions on how to print it out.
The Check Display indicator is lit: Read the message on the LCD display
and check the descriptions listed on page 62.
Othe r Possib le Prob le m s
You want to remove the document in the feeder
Open the document feeder (see page 54), then remove the document.
Caution: Do not pull out the document without opening the auto document
feeder, or you will damage the scanning mechanism.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Cle a ring Doc um e nt Ja m s
Troub le shooting
Cle a ring Doc um e nt Ja m s
If
appears in the display:
Problem: There is a document jammed in the feeder. Remove the jammed
document and repeat the transmission procedure.
Cause: The document may be longer than the maximum limit (see the docu-
ment specifications on page 72).
Grasp the center of the operation
panel and pull forward to open it.
1
If the jammed paper is visible
from the document tray, pull it out
2
from the front of the machine.
If the jammed paper has been fed
right into the machine, hold the
panel open and remove it from in-
side.
Close the panel firmly.
3
Pull the copy output tray forward.
4
Set the document again after
"READY" appears in the display.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Troub le shooting
Cle a ring Copy Ja m s
Cle a ring Copy Ja m s
If
appears in the display, there is a copy jam. .
CAUTION: Do not touch the fusing unit (see the diagram below). It may be
hot.
CAUTION: Do not touch the photoconductor drum (green drum).
CAUTION: Any toner on the paper will not be fixed to the paper. Be careful
not to get your hands or clothing dirty.
CAUTION: Even if you can see the paper from the exit, do not pull it without
opening the cover.
Squeeze in the release button on
the left side of the machine and
open the cover.
1
Carefully pull out the jammed pa-
per from the outside of the ma-
chine. Do not leave any pieces
inside.
2
If the document is very short you
might not be able to see it. In this
case remove the toner cassette
and photoconductor following
steps 2 to 5 on the page 52. Then
remove the jammed paper and re-
install the photoconductor and
toner cassette.
Fusing Unit (white grill)
Close the cover firmly and pull
the copy tray forward.
3
56
Download from Www.Somanuals.com. All Manuals Search And Download.
If Me ssa g e s You Re c e ive Don’t Fit on Your Pa p e r
Troub le shooting
If Me ssa g e s You Re c e ive Don’t Fit on Your Pa p e r
Bre a king Down La rg e Form a t Me ssa g e s
If the incoming document is longer than the paper in your fax machine, the
machine will split it into multiple sheets. The tail end of the message will be
reproduced at the head of the next page. The images overlap each other by
10mm. (You can ask a service technician to turn off the overlap.)
Le ng th Re d uc tion
If the incoming document is too long but still within the limits below, the
machine can reduce it so that it will fit on one page.
Paper size in the cassette
Maximum reducible length
Letter (11")
365.7mm
464.8mm
388.8mm
433.2mm
Legal (14")
A4
F
Com munic a tion p rob le m s
If
appears in the display: Press Stop.
Causes: -A poor line caused the communication to fail.
-The line is busy or noisy. Try to retransmit.
-The other machine is out of order. Ask the other party to check
their machine.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Troub le shooting
Op e ra tiona l Diffic ultie s
Op e ra tiona l Diffic ultie s
Problem
Required Action
STANDBY MODE
Nothing happens when the switch is
turned on.
Check the power cord. Is it properly plugged into
the outlet?
➣
Plug it in firmly
Switch the power on.
Check that the power cord is plugged in.
The machine might be in saving energy mode.
Hold down any key for two seconds.
SET DOC. OR DIAL NO. is not
displayed.
➣
➣
The display does not show the
Ready condition, or the machine
stops during operation.
Does CLEAR ORIGINAL or CLEAR COPY
appear in the display ?
➣
Clear the misfeed. See page 56.
Does ADD PAPER appear in the display?
Load paper into the paper tray. See page 48.
Does CLOSE COVER appear in the display?
Close all covers.
➣
➣
TRANSMISSION
The original is not pulled into the
auto document feeder.
You did not feed the document far enough into
the feeder.
➣
Insert the document into the feeder until it
stops. Retransmit.
Clean the ADF rollers (see page 54).
➣
If the same problem still exists after user
maintenance, contact your service
representative.
The machine cannot dial out.
The telephone line is disconnected.
Check that the line is connected properly.
The telephone line type setting is incorrect.
➣
➣
Check the telephone line type setting
See page 84.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Op e ra tiona l Diffic ultie s
Troub le shooting
Problem
Required Action
The machine cannot dial out from
behind a private switchboard (a
PBX).
The dialed number does not contain an access
code or a pause, or not enough pauses.
➣
Include the access number and a pause
before the telephone number, or add pauses
between the access code and the number,
if necessary.
Frequent original misfeeds
Multifeeds or non feeds
Incorrect positioning of originals
➣
Put the document in the feeder correctly.
Incorrect alignment of originals
Align the edges of the document.
Curled pages
➣
➣
Flatten the document.
Incorrect document type
➣
Use a proper document type. See page 72.
Mixed document types
The pages must all be of the same type.
Static electricity on the originals
Shuffle the document.
Clean the ADF rollers (see page 54).
➣
➣
➣
If the same problem still exists after user
maintenance, contact your service
representative.
Copier silicone oil on the originals
Wait a few minutes, then try again.
More than 30 pages in the feeder
➣
➣
Do not place more than 30 pages in the
automatic document feeder at once.
The document may be longer than the maximum
limit (see page 72).
➣
Make sure that none of your originals exceed
this limit.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Troub le shooting
Op e ra tiona l Diffic ultie s
Problem
Required Action
Transmission cannot take place
The other machine is out of order.
➣
➣
Check the error report.
Ask the other party to check their machine
and correct the fault.
The line is busy or noisy.
➣
Check that the dial tone is sent out.
Try to retransmit.
Documents sent to other fax
terminals arrive blank.
The original must be placed face up in the
document feeder.
➣
Position the original correctly. See page 7.
Consistent difficulty in
communicating with a particular
terminal
There are some bad lines between you and that
other terminal.
➣
Store that terminal’s number as a Quick Dial
Key or Speed Dial Code.
Consistent poor image quality when
communicating with a particular
terminal
Then call a service technician. Inform him of
the nature of the problem and give the
Quick Dial Key or Speed Dial Code that you
stored the number in.
RECEPTION
The telephone keeps ringing and no
fax is printed.
You are in Manual Receive mode.
Change to Auto Select mode (see page 12).
Power is switched off.
Switch the power on.
➣
➣
RECEPTION/COPYING
No printout; the ADD PAPER
appears in the display.
The paper trays are empty.
Add paper (see page 48).
➣
The metal plate in the optional paper feed unit is
not raised up.
➣
Press the buton on the left of the paper feed
unit.
No printout; the CLEAR COPY
appears in the display.
The printer has jammed.
Clear the jam (see page 56).
➣
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Op e ra tiona l Diffic ultie s
Troub le shooting
Problem
Required Action
Copies are blank.
Is the toner cassette installed?
Install the toner cassette.
Is the proper paper in the paper tray?
Use appropriate paper. See page 72.
➣
Copy paper misfeeds occur
frequently.
➣
Is folded, wrinkled, damp, or curled paper in the
paper tray?
➣
Always use dry, undamaged paper.
Is the paper set properly in the paper tray?
➣
Always load paper correctly. See page 48.
Do not load too much paper in the trays.
Are there any pieces of misfed paper or other
foreign objects in the machine?
➣
Make sure that the paper path is
completely clear of paper and other
material after a misfeed.
Are you copying onto recycled paper?
➣
Fan the stack of recycled paper and load
it in the paper tray.
Stripes on copies.
TELEPHONING
The exposure glass for the auto document
feeder is dirty.
➣
Clean the exposure glass (see page 54).
You can’t receive phone calls; the
unit only rings once then goes into
receive mode.
You are in FAX mode.
Change to Manual Receive mode or AUTO
mode.
(see page 12).
The telephone line is not connected.
Connect the line (see page 84).
➣
You can’t receive phone calls; the
unit does not ring.
➣
POLLING
Dialing took place, but polling could
not.
Polling with ID is set in the other terminal.
➣
Contact the person at the other end and
make sure that free polling is available.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Troub le shooting
Disp la ye d Error Me ssa g e s
Disp la ye d Error Me ssa g e s
You cannot use the auto-dialer at the moment. Use the ten-key
pad or the handset.
CHECK AUTO-DIALING
No polling reception operations have been programmed.
There are no messages in memory waiting for transmission.
Incorrect file number. Check the file number and try again.
NO FILE EXISTS
The memory cannot hold any more telephone numbers.
Either: Delete some numbers then try again.
Or: Wait until some of the Send Later or other delayed
transmissions waiting in memory have been carried out, then try
again.
TOO MANY DEST.
This Quick Dial Key has a Group stored in it.
USED AS GROUP
This Quick Dial Key has a telephone number stored in it.
This Quick Dial Key is programmed as Dial Option Key.
This Quick Dial Key is programmed as Group Key
USED AS DIAL
USED AS DIAL OPTION
USED AS GROUP KEY
NOT PROGRAMMED
This Quick Dial Key or Speed Dial Code does not contain a
number.
Either:This number is already included in this Group.
This RTI/CSI has already been stored for use with this feature.
ALREADY PROGRAMMED
PLEASE SET PAUSE
TONER LOW
You must add a pause after your area code when you input your
fax terminal’s own telephone number.
Toner has nearly run out. You can still make copies but must
change the cartridge soon.
The toner cartridge is empty. Install a new cartridge.
The cassette is now empty.
ADD TONER
ADD PAPER
A document is jammed in the feeder.
CLEAR ORIGINAL
CLEAR COPY
CLOSE COVER
Paper is jammed in the printer.
A cover is not closed properly. Check that all covers are closed.
SERVICE CALL
H
Machine is out of order. Contact your service
representative. Be sure to write down the code numbers
and have it handy when you call for service.
CHECK PAPER SIZE
The size of the installed paper does not match the
currently selected paper size.
Set the paper size (see page 82) or install the appropriate
paper.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Ca lling the Se rvic e Sta tion
Troub le shooting
Ca lling the Se rvic e Sta tion
The machine has a feature called Service Report Transmission. Use this
feature when your machine is having problems. The machine will transmit
information about the condition of your machine to your service representative.
A technician will then be able to find out what the problem is before making a
visit. Service Report Transmission is available when the fax number of the
service representative has been programmed.
Se nd ing a Se rvic e Re p ort
When you need to send a service report, do the following.
Function 6 2 2 2 2 7 2 and Yes.
1
Start.
2
If the transmission was not successful, the machine will not redial. You must
repeat the operation. Program your machine’s own telephone number in order
for your service representative to identify the sender of the service report.
(Function 61: see page 88)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL REFERENCE
Ac c e ss Cod e for Func tions 61 to 94
Accessing functions 61 to 94 requires an access code.
The sole purpose of this feature is to keep others from accidentally
misadjusting the machine. This code cannot be changed, so do not rely on it as
a security feature.
The code is 2222
Use r Pa ra m e te rs (func tion 63)
Adjusting your machine sometimes requires that you change special settings
called user parameters. For each user parameter, you must change a bit in a
switch.
bit values
Example:
Switch
3 2 1 0
7 6 5 4
bit
A switch has eight bits. Each bit has a value of 1 or 0, and each bit is numbered
0 to 7 from the right. In the following example we’ll change bit 3 of switch 05 in
the user parameters.
Press Function and 6, enter the
access code 2 2 2 2 then press
6, 3, and Yes. You’ll get:.
1
(You can press to see a list. Oth-
erwise, press Yes.)
Press Yes again and use the
&
2
keys to change switches. For ex-
ample go to switch 05 by press-
ing five times.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Use r Pa ra m e te rs (func tion 63)
TECHNICAL REFERENCE
To change bit 3, press 3 on the
key pad. Bit 3 will change from 1
to 0 or from 0 to 1.
3
(To change bit 0, press 0, to
change bit 1, press 1, and so on.)
Press Yes and Function.
4
Here is a list of all relevant user parameters. Many bit settings have no effect
and are not listed. (Never change these). The settings made at the factory are
underlined.
SW
Digits & Definition
0, 1, 2 and 3
Settings
00
Do not change these settings
4, 5: Default resolution when you
send a message
Bit
4
0
1
0
1
5
0
0
1
1
Standard
Detail
Fine
Halftone
6: Default setting for transmission
7: Clear modes after sending a fax.
Memory: 0
Immediate: 1
01
Off: 0
On: 1
65
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL REFERENCE
Use r Pa ra m e te rs (func tion 63)
SW
Digits & Definition
Settings
03
0: Automatically print memory
transmission reports.
Off: 0
On: 1
2: Automatically print storage
reports for memory transmission.
Off: 0
On: 1
4: Automatically print polling
reception reports.
Off: 0
On: 1
5: Automatically print immediate
transmission reports.
Off: 0
On: 1
7: Automatically print communication
reports.
Off: 0
Yes: 1
04
05
7: Include the first half of the first
page with reports?
Off: 0
On: 1
0: Store incoming faxes when
machine is out of supplies.
Off: 0
On: 1
1: Allow automatic reception from
senders that do not identify
themselves.
Accept (Free): 0
Reject (RTI/CSI): 1
6, 7: Level for the Energy Saving
feature
Bit
6
0
1
7
0
0
Heater off:
Heater half cool:
06
0: Send a header with each page.
4: Batch Transmission
Off: 0
On: 1
Off: 0
On: 1
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Use r Pa ra m e te rs (func tion 63)
TECHNICAL REFERENCE
SW
Digits & Definition
Settings
08
2, 3:
Bits
(Can also use function 62)
2
0
1
3 :
X: Off
0: Receive messages only from
senders whose RTI/CSIs are
programmed.
1
1: Receive messages only from
senders whose RTI/CSIs are
programmed.
10
12
7: Use dithering halftone (SPD) or
standard halftone (STD)?
STD: 0
SPD: 1
2: Faxing & Report Toner Saving Off: 0 On: 1
Note:
If on, contrast will be set to "Normal" automatically, preserving image quality.
This is available when receiving fax messages and printing reports, but not
for copying.
Further, messages sent to you in halftone mode will automatically turn off
toner saving to insure a clear image.
To make sure that the fax quality is acceptable with toner saving on, print a
few reports.
(Note: If the sender is using a machine made by another manufacturer, toner
saving will stay on and this could lower image quality.)
3, 4: Fax reception
density
Bit
3
0
0
1
4
0
1
0
Normal:
Darken:
Lighten:
13
Access to the public telephone line
Bit
0
1
Loop Start
Ground Start
0
0
0
1
(This feature is not available in
France.)
Flash Start
PSTN
1
0
1
0
67
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL REFERENCE
Use r Pa ra m e te rs (func tion 63)
Use r Pa ra m e te r Hints
C ha ng ing yo ur ma c hine ’s d e fa ult se tting s
These are the settings your machine assumes immediately after it is turned on,
after clearing the machine, or after you or the night timer reactivates it. Many of
the user parameters determine your machine’s default settings.
C le a r m o d e s a fte r se nd ing o r lo a d ing a fa x m e ssa g e (Switc h 01, b it 7)
Your machine can either reset itself or keep its settings (for a few minutes) after
it sends a fax message.
Auto ma tic re p o rts
Many types of automatic reports can be switched on or off. See page 32 for
details.
Ac c e p ting m e ssa g e s whe n o ut o f sup p lie s (Switc h 05, b it 0)
This is also called substitute reception. You can accept messages even when
out of toner or paper by storing them in memory. See page 14
.
Sa ving to ne r (Switc h 12, b it 2)
You can reduce the amount of toner used for fax messages and for reports.
Messages sent to you in halftone (e.g. photographs) will switch this feature off
to ensure the best image quality available, but the feature will stay on if the
sender is using a machine made by another manufacturer. To make sure the
fax quality is acceptable, print a few reports (see page 32). If you find that your
fax messages and reports are too light, turn this feature off.
Ad justing the d e nsity fo r fa xe s (Switc h 12, b its 3 & 4)
If your received fax messages are too light or too dark, adjust the printing
density over three levels: Normal, Darken, and Lighten.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Ad justing the Volum e of Va rious Fe a ture s
TECHNICAL REFERENCE
Ad justing the Volum e of Va rious Fe a ture s
(Func tion 92)
You can change the beeper (monitor) volume of the desired feature.
Beeps to signal transmissions.
Beeps to signal receptions.
Beeps to signal on hook dialing.
Beeps when a number is dialed.
Press Function, 6, and enter the
access number 2222. Then press
9, 2.
1
Press Yes.
2
Adjust the transmission monitor
3
volume with
&
and press Yes
when you’re done.
Adjust the reception monitor vol-
4
5
6
7
ume with
&
and press Yes
when you’re done.
Adjust the on hook monitor vol-
ume with
&
and press Yes
when you’re done.
Adjust the dial monitor volume
with
&
and press Yes when
you’re done.
Press Function to return to the ready state.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL REFERENCE
Se le c ting the Disp la y’s La ng ua g e
Se le c ting the Disp la y’s La ng ua g e
(Func tion 93)
If you would rather use another language for messages and displays, follow the
procedure below. The six languages available are: English, German, Italian,
Spanish, French, and Swedish.
Press Function, 6, and enter the
access number 2222. Then press
9, 3, and Yes.
1
Use and to scroll through the
available languages.
2
Press Yes to accept the language displayed, then press Function to
return to the ready state.
3
Counte rs (Func tion 94, se e p a g e 37. )
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Ente ring Cha ra c te rs
TECHNICAL REFERENCE
Ente ring Cha ra c te rs
Use the key pad for entering numbers. Use Quick Dial keys 1 to 8 for entering
letters, the keys to change to another letter, the Yes key to accept a
&
character, and Quick Dial key 10 for spaces and other characters.
If at any time you make a mistake when entering a character or digit, press the
Clear key to erase it. To correct a character or number already entered, use the
and keys to reach the mistake, enter the new character, and press clear to
erase the mistaken character. If you press the No key, whole characters are
erased.
Quick Dial Key
Letters
A --C
D - F
G - I
Quick Dial Key
Letters
P - R
01
02
03
04
05
06
07
08
09
10
S - U
V - Z
J - L
Nothing
M - O
Space & Symbols
Ente ring Sym b ols
Press 10 of the Quick Dial key.
1
2
Press or to scroll symbols.
You can enter the following symbols.
"Space" & $ ! " # $ % & ’ ( ) * + , / : ; < > ? @ [ ¥ ] ^
Press Yes.
3
Ente ring Num b e rs
Enter numbers using the ten key pad.
1
71
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL REFERENCE
Doc um e nt & Pa p e r Sp e c ific a tions
Doc um e nt & Pa p e r Sp e c ific a tions
Documents (Using the Auto Document Feeder)
Length :
Width:
105~600mm
148~216mm
0.05 ~0.2mm (50 to 90 g/m )
2
Thickness :
Doc um e nt Fe e d e r Re q uire m e nts
❐ Do not insert torn, heavily curled, wavy, creased, dog-eared, damp, or otherwise
damaged documents. Make copies of these originals and scan the copies.
❐ Do not insert folded, stapled, clipped, glued, or taped documents, or documents
with a metallic coating. Make copies of these originals and scan the copies.
❐ Do not insert documents on which there is undried ink or correction fluid. Wait for
the document to dry.
❐ If the document has an uneven or slanted edge, do not insert that edge in first.
Paper Requirements
❐ Acceptable sizes are letter, legal, A4 and F4.
When a received fax message is printed, a margin of 4mm on all four sides is left
blank. To avoid loss of information, the sender should make sure their message
does not run over these margins.
❐ Do not print to torn, heavily curled, wavy, creased, dog-eared, damp, or
otherwise damaged paper.
❐ Do not print to folded, stapled, clipped, glued, or taped paper.
❐ Do not print to paper with any kind of coating or printing. Do not print to metallic
paper. Do not print to the reverse side of a print.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Ca p a b ilitie s
TECHNICAL REFERENCE
Ca p a b ilitie s
Func tions Tha t Ca n Be Use d Tog e the r (Dua l Ac c e ss)
Job you wish to carry out at the same time
(Second selection)
Job currently in progress
1.
2.
3.
4.
5.
6.
7.
8.
9.
(First selection)
✔
✖
✖
✔
✖
✖
✖
✖
✖
✖
✔
✖
✔
✖
✖
✔
✖
✖
✖
✖
✖
✔
✖
✔
✖
✖
✖
✖
✔
✖
✔
✖
✖
✖
✖
✖
1. Storing to Memory
✔
✖
✔
✖
✔
✔
✔
✔
2. Printing from Memory
✖
✖
✖
✖
✖
✖
✖
3. Copying
✖
✖
✔
✖
✔
✔
4. Printing an Automatic Report
5. Immediate Transmission
6. Memory Transmission
✖
✖
✖
✖
✖
✖
✖
✖
✖
✖
✖
✖
7. Receiving and Printing a Fax
8. Receiving a Fax to Memory
9. Transmitting a Service Report
✔: Possible, ✖: Not possible
✖
✖
✖
Store d Num b e rs (Long te rm )
❐ 10 Quick Dial keys, each of which can hold an individual number. Any three of
the Quick Dial keys can hold a group of numbers.
❐ 50 individual numbers stored as two-digit Speed Dial codes (see page 21).
❐ Three groups, each of which can hold up to 30 destinations.
❐ 30 CSI or RTI codes (possibly used as wild cards) for authorized reception.
Store d De stina tions
❐ You can send to as many as 30 locations for one job.
❐ Up to 100 destinations can be set at any one time. (Ex: message A to 25
destinations, message B to 50, message C to 24 and finally one immediate
transmission job you’re programming in now. Total: 100)
73
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL REFERENCE
File Stora g e
Sp e c ific a tions
❐ You can have as many as 100 memory transmission files stored in the machine:
This is a theoretical maximum. The actual number of files you can have in your
machine depends on the types of the documents, and how much memory they
consume.
Sp e c ific a tions
Electrical Specifications (Base machine)
Power supply:
220-240 Vac, 50/60 Hz (Only 50Hz
is printed on the rating plate of
some machines.)
Power consumption
Energy saver mode:
Standby mode:
Average 8 W
Average 24W
Average 35W
Average 180W
Average 195W
470W
Transmission:
Reception:
Copying:
Maximum power consumption:
Fax Specifications
Protocol:
G3
Memory Capacity:
Base Machine: 18 pages/A4 size
With 1Mbyte memory: 102 pages
With 2Mbyte memory: 186 pages
Data rate:
14,400/12,000/9600/7200/4800/
2400 bps, automatic fallback.
Transmission time:
6 seconds at 14,400 bps, G3,
without TTI, ECM, MMR- using
memory for a ITU-T #1 test docu-
ment (Slerexe letter) at standard
resolution
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Sp e c ific a tions
TECHNICAL REFERENCE
General Specifications
Fax mode resolution:
(main scan x subscan)
Standard: 8 x 3.85 lines/mm
Detail:
Fine:
8 x 7.7 lines/mm
8 x 15.4 lines/mm
2
Paper cassette capacity:
Auto document feeder capacity:
Paper Size:
150 sheets (80g/m )
30 sheets, face up
Letter, Legal, A4, F4
380 x 341 x 219 mm
Dimensions (W x D x H):
exclusive of trays, handsets, and options
Weight:
7 kg
exclusive of trays, handsets, and options
Optional Lower Paper Cassette
Capacity:
2
250 sheets (80g/m )
Paper Size:
Letter, Legal, A4
75
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Ma c hine Environm e nt
INSTALLATION
Before installing your machine, read the safety instructions at the beginning of
this manual. To install the machine, follow these procedures:
1-Find a suitable location for the machine.
2-Remove all the pieces of tape attached to the machine.
3-Install the photoconductor and toner cassette. (See page 78.)
4-Attach the accessories and load the paper in the paper tray. (See page 79.)
5-Connect the phone line. (See page 84.)
6-Connect the power. (See page 86.)
7-Enter all necessary information and settings in your machine’s memory.
(See page 87.)
Ma c hine Environm e nt
WARNING: When choosing a location for your machine, please follow the
safety instruction given on pages i to iv of this manual.
Loc a tion
For the best possible performance, install your machine in a place which
satisfies the following conditions.
❐ Not exposed to direct sunlight
❐ Well ventilated (air turnover at least three times per hour); to avoid the
build-up of ozone, make sure to locate the machine in a large well-venti-
3
lated room which has an air turnover of more than 30 m /hr per person.
❐ Level
❐ Not subject to vibration
❐ Away from other electronic equipment, to avoid interference
❐ Away from areas containing corrosive gas
❐ Dust-free
❐ Condensation-free
❐ Temperature 15 to 25°C
❐ Humidity 35 to 70% RH (do not install near a humidifier)
❐ Away from heaters and air conditioners, to avoid sudden changes of tem-
perature
❐ Within 5 meters of a three-pin grounded power outlet (220-240 Volts,
50/60 Hz; Only 50Hz is printed on the rating plate of some machines.)
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma c hine Environm e nt
INSTALLATION
❐ Ensure there is clearance around the machine, as indicated in the dia-
gram below.
30cm
10cm
10cm
NOTE: This machine generates a certain amount of ozone. Although the
amount generated is within safety requirements, it is recommended that, to
avoid ozone buildup, you install the machine in a room which is properly
ventilated.
Op e ra ting Pre c a utions
❐ While the machine is in operation, do not turn off the main switch or un-
plug the power cord.
❐ Keep corrosive liquids, such as acid, off the machine.
❐ Do not allow paper clips, staples, or other small metallic objects to fall in-
side the machine.
❐ The fusing unit may be very hot. Be careful when handling it.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Insta lling the Photoc ond uc tor a nd Tone r Ca sse tte
Insta lling the Photoc ond uc tor a nd Tone r Ca sse tte
❐ First of all, remove all the pieces of tape attached with the machine.
Before using the machine, install the photoconductor and toner cassette as
follows:
Squeeze in the release button on
the left of the machine and open
the cover fully back.
1
Put in the photoconductor as
shown. The left and right ends
are marked "L" and "R" respec-
tively.
2
Shake the toner cassette from
side to side before installing it.
3
Put in the toner cassette. Make
sure it sinks right down.
The right end is marked "2".
Close the cover firmly.
4
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Insta lling the Ma in Pa p e r Tra y
INSTALLATION
Insta lling the Ma in Pa p e r Tra y
Slide the paper guide to the mid-
dle.
Caution: Hold the guide at its
1
base to avoid damaging it.
Check you have the cassette the
right way up. Holding the tray at a
slight angle as shown, fit it into
the holes provided.
2
Important: Hold the tray angled
to the the right to avoid damaging
it.
Slide the paper guide back to the
right. And fit the wire as shown
below.
3
Atta c hing the Doc um e nt Tra y
Fit the wire into the holes pro-
vided.
1
79
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Insta lling the Auto Doc um e nt Ta b le
Insta lling the Auto Doc um e nt Ta b le
Fit the document table to the front
of the machine as shown.
Note: For long documents fold
1
out the wire extension.
Insta lling the Copy Tra y
Hold the copy tray so it curves
away from you and fit it into the
holes provided.
1
Slant the left edge in first.
Pull the copy tray forward.
Note: For long paper fold out the
wire extension.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Insta lling the Op tiona l Pa p e r Fe e d Unit
INSTALLATION
Insta lling the Op tiona l Pa p e r Fe e d Unit
Set the drawer in the cassette
and pull it fully out.
1
Set the guide in the slot appropri-
ate to the paper size you wish to
use.
2
To change the paper size, pull
back and lift out the paper size
guide. Then set the guide in the
slot appropriate to the paper size.
Press down the metal plate inside
the drawer.
3
Place the paper in the drawer so
it is flush with the rear wall. Do
not fill up the cassette past the
load limit marker.
4
Load limit
81
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Se tting the Pa p e r Size
half-moon shaped roller
Slide the draw until the paper just
5
6
touches the front and back of the
draw rightly.
Then press the button on the left
of the cassette to raise the metal
plate.
Make sure that the half-moon
shaped roller has its curved edge
on top.
Place the machine onto the paper
feed unit.
Warning: Watch your fingers!
Note: If any foreign matter (especially glue) is on the copy paper, print quality
may deteriorate. Make sure the front, back and sides of the copy paper are
completely clean.
Se tting the Pa p e r Size
Use the following procedure to select which paper size the machine will use for
the printouts. For example if you wish to use Legal size paper, install the Legal
size paper into the feed. After done that, choose "LEGAL" using Function 34 or
key.
Press the Function key and 3, 4,
using the ten keypad, then press
the Yes key.
1
Or
Press the key.
Current paper size appear in the
display. Scroll the paper size us-
ing the key then press Yes.
2
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Se tting the Pa p e r
INSTALLATION
Either:
3
❐ If only one cassette is installed, press
Function to finish.
❐ If you have an optional lower cassette in-
stalled, you will be prompt for the paper
size. Repeat the same procedure in the
second step. And press Function to fin-
ish.
Se tting the Pa p e r
See the section titled "Setting / Adding the paper". See page 48 .
Insta lling the Op tiona l Me m ory Ca rd
Switch off the power before you install the optional memory card.
Open the cover.
1
Insert the card with the side with
the card type (e.g. TYPE 20)
printed on it facing away (facing
right) from the machine.
2
Close the cover firmly and pull
the copy tray forward.
Turn the power back on.
3
83
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Conne c ting the Ma c hine
Conne c ting the Ma c hine
Before using the machine, connect the machine to the telephone line properly.
Then plug in the power cable and switch on.
Make sure the machine is properly connected to the telephone line and the
power outlet, as shown below.
CAUTION
Do not switch on until everything is connected properly.
Program the Telephone Line Type setting (use Function 62; see page 90). If
your telephone normally sends out tones(touch tone) when dialing, use the TT
setting; if it normally sends out pulses (rotary dial), use the DP setting. Also,
make sure that the switch on the handset is set up correctly.
Conne c ting to the Phone Line s
Important: By law in the United States, you must program your phone number
identification (your CSI) into your machine before you can connect
it to the public phone system. See page 87.
[A]
[B]
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Conne c ting to the Phone Line s
INSTALLATION
Connect the phone line cord to the upper fax jack marked Line [A].
1
2
Connect the other end of the line into the phone line jack (on the wall or
on a cable).
Connect the handset (option) or your own telephone to the lower jack
marked Tel [B].
3
4
Connect the other end of the line to the handset or telephone.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Conne c ting the Powe r
Conne c ting the Powe r
IMPORTANT POINTS ABOUT POWER CONNECTION
If you have to use an extension cord, make sure that it is capable of carrying
300V/10A, and that your facsimile terminal is the only piece of equipment
connected to that cord. The supply from the wall outlet must not fluctuate more
than 10 V either side of 230 Vac.
The power cord should not be laid in a place where it might trip somebody.
Do not lay anything on the power cord.
WARNING: The power source must conform to the specifications on page 74.
WARNING: Make sure the power source is properly grounded.
WARNING: Follow the safety instructions given of pages i to iv.
Insert the plug into the wall outlet.
1
Turn on the power.
2
Power Source
220-240 Vac.
50/60Hz (Only 50Hz is printed
on the rating plate of some
machines.)
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Initia l Se tting s & Ad justm e nts
INSTALLATION
Initia l Se tting s & Ad justm e nts
Important: The CSI code (see below) is required by international law. You
cannot legally connect a fax machine to the telephone system if
the CSI code is not programmed. Further, the TTI code and the
date and time of transmission must be included in the header of
all pages faxed to, from, or within the United States.
Before you connect your machine to the telephone system, you must enter a
few settings and make a few adjustments.
Own number: The phone number used by your fax line.
CSI (Called Station Identification, required by international law): This is your fax
machine’s phone number, which must include country and area codes. During
any communication, your CSI appears on their display. (Conversely their CSI
appears on your display.)
RTI (Receive Terminal Identification): This should be your name or company
name, in 20 characters or less. During a communication, if the other party’s fax
machine supports RTI, then this replaces the CSI above. The other party’s
name will appear on your display, and yours on theirs.
TTI (Transmitter Terminal Identification):This should be the same as your RTI or
CSI code. It will be printed on the header of every page you send.
Access number If you select inside line, you must program the number which
proceeds the telephone number.
Line: You must match the fax machine to the type of line you use: a tone line or
a pulse line. Then, you should connect the line to the machine.
Date & Time: Necessary for many functions and required in the USA.
Initia l Se tting s (Func tion 61)
During the course of this procedure you’ll have to enter letters and other
characters.
Use the key pad for entering numbers. Use Quick Dial keys 1 to 8 for entering
letters, the
&
keys to change to another letter, the Clear Key to erase a
letter, Yes key to accept a character, and Quick Dial key 10 for spaces and
other characters. See page 71 for details.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Initia l Se tting s & Ad justm e nts
If these settings have been made before, the messages on the display will not
always match those shown here. The setting already entered will appear along
with the word [
]. In this case, press Yes to change the setting.
Press Function and 6, enter the
access code 2222, then enter 61.
You’ll get this:
1
2
3
4
Press Yes.
Press Yes again.
Enter your phone number.
❐ The format of the number is normally as follows:
International Dial Prefix, Your Country Code, Your Area Code, then you
must add a Pause, followed by your telephone number.
Check the International Dialing Prefix and the Country Code with your lo-
cal telecommunications operator. The example shown is for the USA; the
codes to add are 011 and 1.
Press Yes.
flash on the display and you’ll get
will
5
Press Yes.
6
7
Enter your office, company, or per-
sonal name, or any other appro-
priate identification. (Use the
quick Dial keys. See page 71 for
details.)
Press Yes.
flash on the display and you’ll get:
will
8
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Initia l Se tting s & Ad justm e nts
INSTALLATION
Press Yes. The RTI programmed
in step 7 appears. You should
keep it.
9
If you wish to change it, press
Yes and edit the TTI.
Press No to keep the TTI as is.
You’ll get:
A
Press Yes.
B
Enter your phone number and in-
clude the country and area code,
(but no pauses). Should be the
same as in step 4.
C
Press Yes.
flash on the display and you’ll get:
will
D
Se tting the Ac c e ss Num b e r
Press the Function key and
press the Yes key.
1
Press the key until the screen is
shown opposite.
2
Press the Yes key.
3
Enter the number which you use
to access an outside line.
4
Press the Yes key to store your setting, the press the Function key.
5
89
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Initia l Se tting s & Ad justm e nts
Se tting the Phone Line (Func tion 62)
Press Function and 6, enter the
access code 2, 2, 2, 2, then enter
62. You’ll get this:
1
Press Yes.
2
Press Yes again.
3
Press
&
to set your machine
4
5
for a tone dial line ( ) or a pulse
dial line ( ).
Press Yes.
flash on the display and you’ll get
this.
will
At this point, you could turn on
the Authorized Sender function
(page 37). We will skip this
Press Function.
6
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Initia l Se tting s & Ad justm e nts
INSTALLATION
Se tting the Da te & Tim e (Func tion 91)
Press Function, 6, and enter the
access code 2222. Then enter
9 1.
1
PressYes. A date and time will
appear.
2
Change the date with the ten key-
pad as 09.
3
Change the month using * or # (*
to scroll forward, or # to scroll
backward) on the ten key pad
and press to move the cursor.
4
Type in the year and time at the
keypad as 9 6 1 0 2 5.
5
When the display is correct, press Yes and Function
6
91
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Initia l Se tting s & Ad justm e nts
Da ylig ht Sa ving Tim e
Whenever local custom requires advancing the clock or setting the clock back,
use this feature. You can easily move the clock forwards when daylight saving
time begins, and back when it ends.
When you install the machine for the first time, take care that the setting is
correct before you set the date and time.
Press Function, 6, and enter the
access code 2222. Then enter
6 2 then press Yes.
1
Press until the screen is as
shown opposite, and then press
Yes.
2
Use the and arrows on the
scroll key to switch the feature on
or off. This mode is off if the dis-
play is shown as opposite.
3
To store your setting: Yes
4
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Position of the Laser Label
WARNING: Do not attempt any maintenance or troubleshooting other than that
mentioned in this manual. This machine contains a laser beam generator and
direct exposure to laser beams can cause permanent eye damage.
So, do not remove cover inside the machine, because the laser generator
exists inside the machine as follows.
Download from Www.Somanuals.com. All Manuals Search And Download.
CLASS 1 LASER PRODUCT
IN ACCORDANCE WITH IEC 825
LASER KLASSE 1 nach IEC 825
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE TO USERS (Great Britain)
This model is designed and approved for connection to the following circuits.
British Telecom Public Switched Telephone Network
Hull Public Switched Telephone Network
PABX Extensions
Mercury Communications Limited Public Switched Telephone Network
CONNECTION TO THE PSTN OR A PABX EXTENSION
If there is a line or jack socket already installed you may connect this model using the line lead
supplied. If you require a socket to be fitted, complete the attached form and send it to your
local telephone manager’s office.
IMPORTANT NOTICE
1. The connection to the BT network must be unplugged before the earth is disconnected.
2. The connection to the BT network must not be hard wired.
3. Please ensure that connection to the mains supply (240VAC), is correctly made and that the
power is switched on before use.
4. The apparatus is suitable for direct connection to exclusive lines of Public Switched Telephone
Network, and for connection to compatible PABXs (consult your authorised dealer for the list of
compatible PABXs and for installation thereon), or via an RBS. The definition of an RBS
(Relevant Branch System) for PSTN lines, is given in BS6789 section 6.1, clause 2.4.
5. When idle, this model allows normal use of an associated main telephone, which must be
plugged into the BS6312 compatible connector, provided for telephone line connection. Only
one such connection may be made.
6. The apparatus must be connected to PSTN lines which use loop disconnect or DTMF signalling.
7. The machine is not suitable as an extension to a payphone, for use on shared service lines, or on
1 - 1 carrier systems.
8. The Terminal operates in mode 1 (autodialling).
9. The user is advised to check all numbers stored in the register before making a call.
10. The approval of this terminal for connection to the British Telecom public switched telephone
network is INVALIDATED if the apparatus is subject to any modification in any material way not
authorised by BABT or it is used with, or connected to:
a) Internal software that has not been formally accepted by BABT.
b) External control software or external control apparatus which causes the operation of the
terminal or associated call set-up equipment to contravene the requirements of the approval.
All apparatus connected to this terminal and thereby connected directly to the British Telecom
public switched telephone network must be approved apparatus as defined in Section 22 of the
British Telecommunications Act 1984.
Download from Www.Somanuals.com. All Manuals Search And Download.
11. This apparatus has been approved for the use of the following facilities:
Storage of Telephone Numbers for Retrieval by Predetermined Code
Automatic Call Initiation
Operation in the Absence of Proceed Indication (Although not Detected)
Automatic Dialling Facilities
Auto-Calling Facility
Loudspeaking Facility
Series Connection Facility
Automatic Storage of Last Number Dialled
Tone Detection - Busy Tone
Repeat Attempt Facilities: Multiple (Automatic)
Auto Clear from Call Originating End
Integral Modem
Any other usage will invalidate the approval of the apparatus if as a result it then ceased to
conform to the standard against which approval was granted.
13. Connection to a PBX - it cannot be guaranteed that the apparatus will operate correctly under
all possible conditions connection to compatible PBX’s. Any cases of difficulty should be referred
in the first instance to the supplier of the telephone apparatus.
14. This apparatus provides an off hook detector and switching of the line between the telephone
and modem. The voltage drop introduced by this apparatus into the loop connection between
the main telephone and the network at a current of 40ma d.c. is 0.3 volts.
15. Only apparatus conforming with BS6301 or EN41003 may be connected to the series socket.
Any interconnection between the above socket and other connections, directly or by the way of
other apparatus, may produce hazardous conditions on the BT network. Advice should be
obtained from a competent engineer before any such connection is made.
16. With reference to EN41003 cl 4.1.3 the apparatus is supplied with a connection to the Public
switched telephone network, which is refered to as a TNV circuit. There is also an optional
printer port that may be fitted, which is refered to as a SELV circuit.
Please ensure that the TNV circuit is only connected to another TNV circuit and that the SELV
circuit is only connected to other SELV circuit.
17. The apparatus does not recognise a secondary proceed indication.
18. Although this equipment can use either loop disconnect or DTMF signalling, only the
performance of the DTMF signalling is subject to regulatory requirements for correct operation.
It is therefore strongly recommended that the equipment is set to use DTMF signalling for
access to public or private emergency services. DTMF signalling also provides faster call set up.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fa xing a t a Gla nc e
Op tion ke y
Fan your stack. (At most 30 one sided pages)
?
Sending or picking up a fax
message later (page 16 )
1
Insert the document face up in the feeder.
Setting the number of pages
2
Select Memory (LED on) or Immediate
Transmission (LED off) with the Memory key.
Printing an ID at the top of
your message
3
Dial the number either from the keypad, with
a Quick Dial key (at the left), or with a Speed
Dial code.
4
Press Yes and dial more numbers (if
needed). Finally press the Start key.
Hints
5
❐
❐
Problem? See page 54
❐
Follow the safety
instructions at the
beginning of this manual.
To change the toner
cartridge, see page 50.
❐
Use Quick Dial keys
01 to 08 to enter letters
and Quick Dial key 10
to enter spaces and
symbols.
❐
❐
To add paper, see
page 48.
❐
Use the Yes & No keys
(
&
) to accept or
reject settings.
Use the Function,
,
❐
If your telephone line
uses pulse dialing, see
page 46 for how to
generate tones.
and keys to navigate
through functions and
options.
Func tions: Press the function key followed by one of the numbers below.
11
Picking a document stored elsewhere (page 30)
61*
Initial Settings:
Own telephone number
RTI (a name ID sent to other machines)
TTI (an ID printed on messages you send),
CSI (phone ID sent to other machines).
PSTN accessing code
21
22
Erasing a message stored for transmission (page 28)
Erasing instructions to pick up a document (page 28)
31
32
33
Storing a number in one of the Quick Dial keys at left
(page 21)
(page 87)
62*
63*
Selecting the phone line , turning authorized reception
and the timer on or off.
(page 90)
Storing a number as a two-digit code (page 21)
Storing a group of numbers (page 23)
Setting the paper size (page 82)
Printing and setting user parameters ( bit switch
settings for a variety of functions, page 64).
34
41
71*
81*
Night timer (page 43).
Checking the last 35 communications (prints out a
report, page 34)
Setting the list of specified senders (for authorized
reception, page 37)
42
43
51
Printing a list of all messages and pick-up files stored
in the machine (page 35)
91*
92*
93*
94*
Adjusting the clock (page 91).
Adjust the volume (page 69).
Selecting a different language (page 70).
Counters (page 37).
Printing a list of all the telephone numbers stored in
the fax machine (page 36)
Printing a message stored in the machine (page 29)
*These functions require the access code on page 64.
Download from Www.Somanuals.com. All Manuals Search And Download.
Photocopy this cover and use as a quick reference.
English
Declaration of Conformity
"The Product complies with the requirements of the EMC Directive
89/336/EEC and the Low Voltage Directive 73/23/EEC."
German
Konformitätserklärung
"Das Produkt entspricht den Anforderungen der EMV-Richtlinie 89/336/EWG
und der Niederspannungsrichtlinie 73/23/EWG."
French
Déclaration de conformité
"Le produit remplit toutes les conditions requises par la directive EMC
89/336/ CEE ainsi que la directive faible voltage 73/23/CEE."
Italian
Dichiarazione di conformità
"Il prodotto è conforme ai requisiti della direttiva CEE 89/336 EMC e della
direttiva CEE sulla bassa tensione 73/23."
Spanish
Declaración de conformidad
"Este producto cumple con los requisitos de la Directiva sobre
Compatibilidad Electromagnética 89/336/EEC y con la Directiva sobre
Baja Tensión 73/23/EEC."
Swedish
Försäkran
"Denna produkt överensstämmer med kraven i EMC direktivet 89/336/EEC
och Lågspänningsdirektivet 73/23/EEC."
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPPLIES
CAUTION: Ricoh shall not be responsible for any damage or expense that
may result from the use of parts other than recommended parts.
For good copy quality, Ricoh recommends that use genuine Ricoh toner.
TONER CASSETTES
❐ RICOH TONER CASSETTE TYPE 70 is recommended for the best perform-
ance.
PHOTOCONDUCTOR
❐ RICOH DRUM TYPE 70 is recommended for the best performance.
Overseas Affiliates
Netherlands
RICOH EUROPE B.V.
Groenelaan 3 P.O. Box 114
Bundesrepublik Deutschland
RICOH DEUTSCHLAND GMBH
Mergenthalerallee 38-40
1180 AC-Amstelveen, The Netherlands 65760 Eschborn, Germany
TEL: +31-(0)20-5474111
FAX: +31-(0)20-6418601
TEL: +49-(0)6196-906-0
FAX: +49-(0)6196-45104
United Kingdom
USA
RICOH U.K. LTD.
Ricoh House
1 Plane Tree Crescent, Feltham
Middlesex TW13 7HG, U.K.
TEL: +44-(0)181-751-6611
FAX: +44-(0)181-890-5566
RICOH CORPORATION
5 Dedrick Place,
West Caldwell, NJ
07006
Ricoh Company, Ltd.
15-5, Minami-Aoyama 1-Chome, Minato-ku, Tokyo 107, Japan
Part No. H5288601 Printed in the Netherlands
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
|