21-1703 A
Mini Mobile CB Radio
Thank you for purchasing your Mini Mobile CB Radio from RadioShack.
Please read this user’s guide before installing, setting up and using your new
product.
What’s Included
CB Radio
3mm Self-tapping Screw (2)
Spring Washer (2 big + 4 small)
Plain Washer (2 big + 4 small)
Nut (2 big + 2 small)
Microphone
Holder
Mounting Bracket
5mm Machine Screw (2)
3mm Machine Screw (2)
5mm Self-tapping Screw (2)
Mounting Knob (2)
Rubber Washer (2)
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Features
Push to Talk (PTT)
Microphone
Product Features
Channel Display
Shows the current
channel.
CHANNEL
Rotate to select
frequency.
VOLUME
OUT CH9 CH19
Switch to move between standard
frequencies and emergency channels.
Rotate to increase or
decrease the speaker
volume.
TX / RX
SQUELCH
Rotate to adjust the amount of
background noise.
Shows when the radio
is transmitting (TX), or
receiving (RX).
Other Features
Full Legal Power – gives you the greatest available range.
Automatic Noise Limiter – reduces impulse-type noises while receiving.
External Speaker Jack – provides a connection for an external speaker.
Phase-Locked Loop (PLL) Frequency Synthesizer – provides highly accurate and
stable tuning.
Two Built-In Ceramic Filters – ensure superior channel selectivity and freedom
from adjacent channel interference.
Automatic Modulation Control – prevents the transmitter signal from over-
modulating and distorting.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Setup
Attaching the Microphone Holder
You can attach the microphone holder to either side of the transceiver or to
another location in your vehicle.
To attach the holder to either side of the transceiver, secure the holder to the
side using the supplied 3mm self-tapping screws, and spring washers.
Holder
Spring washer
3mm self-tapping
screw
To attach the holder to another location in the vehicle, such as the dashboard,
follow these steps.
1. Using the holder as a template, mark the positions for the mounting screw
holes at the desired location.
2. At each marked position, drill a hole slightly smaller than the supplied
mounting screws.
3. Attach the holder at the mounting location using the supplied 3mm
machine screws, spring washers, plain washers, and nuts.
Note: If you cannot reach behind the mounting surface to attach the nuts on
the machine screws, use the supplied 3mm plain washers and self-tapping
screws.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Mounting the Transceiver
Cautions:
•
•
•
If you use this CB in a vehicle, mount it securely to avoid damage to the CB
or vehicle, or injury to anyone in the vehicle during sudden starts or stops.
Do not mount the CB where it could damage or interfere with the
operation of any passive restraint safety device (an airbag or seat belt).
Be careful not to drill into objects behind the mounting surface.
If you are mounting the CB in a vehicle, choose a location where:
•
•
•
•
You can easily reach the CB.
Wires and cables are clear of the vehicle’s pedals or other moving parts.
The CB is not directly in front of heating vents.
All wires and cables can reach their connection points.
The most common mounting location for this CB is under the vehicle’s
dashboard. However, if you plan to use the CB as a base station, you can place it
on a desk, shelf, or table (see “Using the Transceiver” on p.8).
To mount the CB under your dashboard:
1. Using the supplied mounting bracket as a template, mark the positions for
the screw holes on the mounting surface.
2. At each marked location, drill a hole slightly smaller than the supplied
mounting screws.
3. Mount the bracket to the mounting surface with the supplied 5mm machine
screws, spring washers, plain washers, and nuts.
4. Attach the CB to the bracket using the supplied rubber washers and
mounting knobs.
Note: If you cannot reach behind the mounting surface to attach the nuts on
the machine screws, use the 5mm self-tapping screws and plain washers to
secure the bracket.
Mounting bracket
Mounting knob
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Connecting an Antenna
There are many different types of CB radio antennas for mobile CBs. Each type
has its own benefits, so choose the one that best meets your needs.
Note: If you are using this CB as a base station, see “Using the Transceiver” on p.8.
Once you choose an antenna, follow its mounting instructions. Then route the
cable to the transceiver and connect the cable to the ANTENNA jack on the
back of the transceiver.
For the antenna’s best performance, you should mount the antenna:
•
•
•
as high as possible on the vehicle
as far as possible from sources of electrical noise
vertically
EXT SPEAKER jack
ANTENNA jack
To take advantage of your CB’s maximum range, you can adjust the antenna’s
standing wave ratio (SWR) using an SWR meter (not supplied).
Follow the instructions supplied with the SWR meter and antenna to adjust your
antenna’s SWR to the lowest possible value. SWR values of 2.0:1 are generally
acceptable, with readings of 1.5:1 or lower being more desirable.
Cautions:
•
Avoid routing the cable next to sharp edges or moving parts, which might
damage the cable.
•
•
Do not run the cable next to power cables or other CB antenna cables.
Do not run the cable through the engine compartment or other areas that
produce extreme heat.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Connecting the Microphone
1. Press the tab on the side of the supplied microphone’s plug and insert the
plug into the MIC jack on the front of the transceiver. Be sure the tab is
aligned with the jack’s notch.
Notch
Tab
2. Slide the microphone onto the microphone holder.
To disconnect the microphone from the transceiver, press the tab on the side of
the plug. Then pull out the plug.
Caution: To avoid damaging the microphone, never pull on the microphone
cable.
Connecting an External Speaker
Your transceiver also can be connected to an external CB speaker (not supplied).
Note: When you connect an external speaker, the CB’s internal speaker
disconnects.
The external speaker you use with the transceiver should have an impedance of
8 ohms and be able to handle 3 to 10 watts of power. The speaker cable must
have a 1/8 -inch (3.5mm) plug. Your local RadioShack store carries a variety of
speakers and cables to meet your needs.
To connect the external speaker to the transceiver, insert the speaker cable’s
plug into the EXT SPEAKER jack on the back of the CB.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Using Vehicle Battery Power
To connect the transceiver to the vehicle battery power:
1. Connect the red wire (with the inline fuse holder) on the back of the
transceiver to a point in your vehicle’s fuse
block that has power only when the ignition is
in the ACC (accessory) or ON position.
2. Connect the black wire to a metal part of the
vehicle’s frame (chassis ground).
Caution: Do not connect the black wire to a
Negative (–)
black wire
non-metallic (plastic) part, or to any part
insulated from the vehicle’s chassis by a non-
metallic part.
Positive (+)
red wire
Using the Transceiver
Although this transceiver is designed mainly for mobile use, you can also use
it as a base station with an AC power source. For base station installation, you
need these items (not supplied):
•
•
•
a 13.8V DC power supply that can supply at least 1.5 amps
base station antenna
coaxial antenna cable and connector
Warning: Use extreme caution when you install or remove a base station CB
antenna. If the antenna starts to fall, let it go! It could contact overhead power
lines. If the antenna touches a power line, contact with the antenna, mast, cable,
or guy wires can cause electrocution and death. Call the power company to
remove the antenna. Do not attempt to do so yourself!
Follow these steps to install the CB as a base station.
1. Mount the base station antenna as described in its owner’s manual.
2. Connect the antenna to the ANTENNA jack on the back of the CB.
3. Connect the transceiver’s black power wire to the negative (–) terminal on
the DC power supply.
4. Connect the transceiver’s red wire to the positive (+) terminal on the DC
power supply.
5. Connect the DC power supply to a standard AC outlet.
Caution: Most 13.8V DC power supplies plug into a standard AC outlet to
produce DC power. Before connecting your CB to a 13.8V DC power supply,
read and follow the instructions included with the power supply.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
Receiving Transmissions and Adjusting SQUELCH
1. Rotate SQUELCH fully counterclockwise.
2. Rotate VOLUME clockwise until it clicks to turn on the transceiver. The
channel display lights and the channel appears, and the RX indicator lights.
3. Set OUT CH9 CH19 to OUT if you want to select a channel other than an
emergency channel.
4. Rotate the channel selector until the display shows the desired channel.
5. Adjust VOLUME to a comfortable listening level.
6. To cut out background noise between transmissions, wait until there is no
signal, then slowly rotate SQUELCH clockwise until the background noise
stops.
7. To turn off the CB, rotate VOLUME counterclockwise until it clicks. The
display and indicators turn off.
Note: To receive very weak signals, turn SQUELCH counterclockwise. You will
hear noise between transmissions, but you will also hear weak transmissions
(those not strong enough to break through a higher squelch setting).
Transmitting
Follow steps 1 – 5 in “Receiving Transmissions and Adjusting SQUELCH”.
To transmit, hold down PUSH TO TALK (PTT) on the microphone and speak. The
TX indicator lights. Release PUSH TO TALK when you finish transmitting. The TX
indicator turns off.
To turn off the CB, rotate VOLUME counterclockwise until it clicks. The display
and RX indicator turn off.
Selecting the Emergency Channel
Important: Channel 9 is reserved for motorist assistance and for reporting
emergency information about accidents, hazardous road conditions, and so
on. Always give emergency messages priority on Channel 9. To select the
emergency Channel 9, set OUT CH9 CH19 to CH9. The selected channel
number flashes on the display.
Channel 19 is used by truck drivers for general communication purposes. To
select this channel, set OUT CH9 CH19 to CH19.
To select another channel, set OUT CH9 CH19 to OUT. The previously selected
channel number appears on the display.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operational Hints
Common Uses for CB Radios
•
Warn of traffic tie-ups ahead.
•
Help truck drivers and delivery personnel learn road and traffic conditions
and get assistance in locating destinations.
•
•
•
•
•
•
•
Provide fast help in the event of emergency or breakdown.
Help construction crews coordinate the activities of different work crews.
Assist communication between security officers.
Provide weather and road information.
Contact friends or other CB users on road trips.
Keep in touch with your office or home.
Bring more fun for camping, fishing, and other sports; help locate a friend
or find out what’s cooking back at camp.
Transmission Courtesy
•
Wait for a pause in someone else’s transmission before you ask for a break.
•
If you do not receive an answer to your call after a second attempt, sign off
and wait several minutes before trying again.
•
•
Do not hold down PTT when you are not talking. (This is called dead
keying.)
Assist callers with directions, information about road conditions, and any
other reasonable request.
Using Common 10-Codes
Citizen’s band operators and users have largely adopted the 10 codes for
standard questions and answers. These codes permit faster communication and
better intelligibility in noisy areas.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
This table lists codes adopted by the Associated Public Safety Communications
Officers (APCO)
Code
10-1
10-2
10-3
10-4
Meaning
Code
10-17
10-18
10-19
10-20
10-21
10-22
10-23
10-24
10-25
10-26
10-30
10-31
10-33
Meaning
Your signal is bad.
Your signal is good.
Stop transmitting.
En route.
Urgent.
Contact ___.
Message was received and
understood.
What is your location?
Call ___ by telephone.
Cancel last message.
___ arrived at the scene.
___ assignment complete.
Meet ___.
10-5
Relay information to ___.
I am busy. OR Are you busy?
Out of Service.
10-6
10-7
10-8
In Service.
10-9
Repeat last message.
Negative (NO).
Estimated time of arrival is ___.
Use caution.
10-10
10-11
10-12
10-13
___ in service.
Pick up.
Stand by.
Emergency traffic. Clear the
channel.
Report road / weather
conditions.
10-34
10-41
10-62
What time is it?
10-14
10-15
10-16
Information.
Switch to channel ___.
___ cannot understand.
Message delivered.
Reply to message.
Maximum Range
The maximum range and quality of CB transmissions vary depending on the
following conditions:
•
•
the type and quality of antenna used
the height of the antenna’s mounting location—the higher the antenna,
the better the signal’s range
•
•
•
•
the surrounding terrain—mountains and tall buildings limit the range
weather conditions
the number of nearby CBs operating on the same channel
standing wave ratio (SWR) between the antenna and the CB.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Troubleshooting
If your CB is not working as it should, follow these suggestions to see if you can
eliminate the problem. If you cannot, take the CB to your local RadioShack store
for assistance.
Symptom
Check/Try
CB has trouble receiving.
Turn the transceiver power on. See “Operation” on p. 9.
Secure connections (antenna, microphone).
Adjust squelch.
Radio may not be on an operating channel. Switch
to an active channel.
PUSH TO TALK may be held down. Release PTT.
Adjust the volume.
CB has trouble transmitting.
Turn the transceiver power on.
Secure connections (antenna, microphone).
Check for corrosion in connections. Clean and
tighten connections.
Radio may not be on an operating channel. Switch
to an active channel.
PUSH TO TALK is not firmly pressed down. Press
PTT completely.
The CB does not work at all.
Secure connections.
The fuse may need replacing. See “Replacing the
Fuse” on p. 13.
Channels cannot be selected.
Set OUT CH9 CH19 to OUT.
PUSH TO TALK is held down. Release PTT.
Reducing Noise
Because the CB itself is fairly quiet, most noise you hear is probably from an
external source in your vehicle such as the alternator, another CB, or spark plugs.
The transceiver uses an ANL (Automatic Noise Limiter) circuit to reduce noise.
However, if possible, try to eliminate the noise by finding its source.
You can determine the noise’s source by turning off the engine and operating
the CB with your vehicle’s ignition set to ACC. If the noise is reduced, the
problem is in your vehicle’s ignition or electrical system. Here are a few hints to
help you reduce or eliminate such noise.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
•
•
•
•
•
Make all CB power and antenna wires as short as possible.
Route the power wires away from the antenna wires.
Be sure that the chassis ground connection is secure.
Replace old ignition wires with new, high-voltage, noise suppression wires.
Install noise suppressors on your spark plugs, or install new spark plugs
that have built-in noise suppressors.
•
If problems persist, check your vehicle’s alternator/generator and regulator
gauges. You can reduce the noise from these sources by using bypass
capacitors at the various output voltage points.
Your local RadioShack store has a wide selection of noise suppression
accessories.
Care and Service
Keep the CB dry; if it gets wet, wipe it dry immediately. Use and store the CB
only in normal temperature environments. Handle the CB carefully; do not
drop it. Keep the CB away from dust and dirt, and wipe it with a damp cloth
occasionally to keep it looking new.
If your CB is not performing as it should, take it to your local RadioShack store
for assistance. To locate your nearest RadioShack, use the store locator feature
(843-7422) and follow the menu options. Modifying or tampering with the CB’s
internal components can cause a malfunction and might invalidate its warranty
and void your FCC authorization to operate it.
Replacing the Fuse
The CB’s 2-amp in-line fuse helps protect your CB from power surges and short
circuits. When replacement is required, use a 2-amp, slow-blow glass fuse (not
supplied).
1. Make sure the power source and CB are both off.
2. Hold the fuse holder by both ends, push the ends
Fuse
together, twist one end, and pull them apart.
3. Remove the old fuse and inspect its condition. If it is
blown, insert a new one of the same type and rating.
Fuse holder
If it is not blown, reinsert it.
4. Push the fuse holder ends together and twist one
end.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Specifications
Receiver
Frequency coverage ............... all 40 CB channels (class D) 26.965 - 27.405 MHz
Sensitivity for 10 dB S/N ................................................................................ 0.6 μV
Tight squelch limit ............................................................................. 350 - 2820 μV
Overall audio fidelity for 450 - 2500 Hz ......................................................... -6 dB
Maximum audio output power ................................................................... 6 watts
Cross modulation ........................................................................................... 50 dB
Transmitter
Frequency coverage ............... all 40 CB channels (class D) 26.965 - 27.405 MHz
Frequency tolerance ................................................................................ 1300 Hz
Carrier power at no modulation ................................................................. 4 watts
Spurious emission ......................................................................................... -67 dB
Current drain at no modulation ............................................................... 1300 mA
Modulation frequency response for 450 – 2500 Hz ..................................... -6 dB
Microphone sensitivity for 50% modulation .................................................. 2 mV
General
Power requirements .................................................. 13.8V DC, negative ground
Dimensions (H×W×D) .................... 13/8 × 4¼ × 57/8 inches (35 × 108 × 150 mm)
Weight ............................................................................................ 1 lb 6 oz (640 g)
Included accessories .............................. microphone hanger, mounting bracket
Specifications are typical, individual units might vary. Specifications are subject
to change and improvement without notice.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
RF Emissions
WARNING! The Federal Communications Commission has adopted a safety
standard for human exposure to radio frequency electromagnetic energy
emitted by FCC regulated transmitters. It is up to the user to properly operate
this radio transmitter to ensure safe operation. Please adhere to the following:
Never allow children to operate the radio without adult supervision and the
knowledge of these guidelines. Avoid touching the antenna when transmitting.
Do not use the radio with a damaged antenna. Please contact your local
RadioShack store for a suitable replacement. Use only the supplied accessories
to comply with FCC RF exposure requirements. For more information about RF
The Federal Communications Commission (FCC) does not require you to have
a license to operate this CB. However, the FCC does require that you read and
know Part 95 of FCC Rules. These rules apply to the operation of a Class D CB.
We have provided a copy of these regulations with your CB.
Do not open your CB to make any internal adjustments. Any internal
adjustments can be made only by an authorized service technician.
Unauthorized internal adjustments and/or modifications can lead to illegal
operation as defined by Part 95 of FCC rules. Such illegal operation can lead to
very serious consequences.
Your CB might cause TV or radio interference even when it is operating
properly. To determine whether your CB is causing the interference, turn off
your CB. If the interference goes away, your CB is causing it. Try to eliminate the
interference by either moving your CB away from the receiver or contacting your
local RadioShack store for help. If you cannot eliminate the interference, the
FCC requires that you stop using your CB.
If you cannot eliminate the interference, contact your local RadioShack store for
help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
This product is warranted by RadioShack against manufacturing defects in material and
workmanship under normal use for one (1) year from the date of purchase from RadioShack
company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED
WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE
NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH
RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR
PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option,
unless otherwise provided by law: (a) correct the defect by product repair without charge for parts
and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the
property of RadioShack. New or reconditioned parts and products may be used in the performance
of warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after
the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation
or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102
12/99
Protect the environment by recycling used electronics.
21-1703 A
©2008. RadioShack Corporation.
All rights reserved. RadioShack and RadioShack.com
are trademarks used by RadioShack Corporation.
P/N: AO0309AAA1
06A08
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|