R
MT. VERNON PELLET STOVE
ADVANCED ENERGY (AE)
Portland
Oregon USA
Tested and
Listed by
O-T L
Owner’s Manual
Installation and
Operation
C
US
OMNI-Test Laboratories, Inc.
Models:
MTVERNON-AE-MBK
MTVERNON-AE-PMH
MTVERNON-AE-CSB
MTVERNON-AE-CWL
NOTICE
DO NOT DISCARD THIS MANUAL
•
Read, understand and
follow these instruc-
tions for safe installa-
tion and operation.
•
Leave this manual with
party responsible for use
and operation.
• Important operating and
maintenance instruc-
tions included.
WARNING
WARNING
HOT SURFACES!
Please read this entire manual
before installation and use of this
pellet fuel-burning room heater.
Failure to follow these instructions
could result in property damage,
bodily injury or even death.
Glass and other surfaces are
hot during operation AND
cool down.
Hot glass will cause burns.
•
•
•
•
Do not touch glass until it is cooled
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
NEVER allow children to touch glass
Keep children away
CAREFULLY SUPERVISE children in same room as
• Do not overfire - If any external part starts to
glow, you are overfiring. Reduce feed rate.
Overfiring will void your warranty.
fireplace.
•
Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
• Comply with all minimum clearances to com-
bustibles as specified. Failure to comply may
cause house fire.
flammable materials.
•
Keep clothing, furniture, draperies and other flammable
materials away.
CAUTION
CAUTION
Check building codes prior to installation.
•
Installation MUST comply with local, regional, state and national
codes and regulations.
Consult local building, fire officials or authorities having jurisdic-
tion about restrictions, installation inspection, and permits.
Tested and approved for wood pellets, shelled field
corn, wheat and black oil sunflower seeds. Burning
of any other type of fuel voids your warranty.
•
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
TABLE OF CONTENTS
Section 1: Listing and Code Approvals
A. Appliance Certifications ......................4
B. Mobile Home Approved ......................4
C. Glass Specifications............................4
D. Electrical Rating..................................4
E. BTU & Efficiency Specifications..........4
Section 8: Operating Instructions
A. Fuel Size, Material & Storage .............22
B. General Operation Information...........23
C. Before Your First Fire .........................23
D. Starting Your First Fire........................23
E. Fire Characteristics & Flame Height
Adjustment..........................................24
F. Battery Back-Up System.....................24
G. Ignition Cycles ....................................24-25
H. Quick Start Guide ...............................26-27
I. Frequently Asked Questions...............28
Section 2: Getting Started
A. Design, Installation & Location
Considerations....................................5
B. Locating Your Appliance & Chimney..6
C. Wall Control, Thermostat....................6
D. Draft....................................................6
E. Negative Pressure..............................6
F. Fire Safety ..........................................7
Section 9: Troubleshooting ............................29
Section 10: Maintaining & Servicing Appliance
A. Proper Shutdown Procedures.............30
B. Quick Reference Maintenance Chart..30
C. General Maintenance & Cleaning.......31-35
D. High Ash Fuel Content Maintenance ..35
E. Baffle Removal....................................35
F. Convection Blower Replacement........36
G. Combustion Blower Replacement.......37
H. Glass Replacement.............................37
G
Tools & Supplies Needed...................7
H. Inspect Appliance & Components
and Pre-Use Checklist.......................7
Section 3: Dimensions & Clearances
A. Appliance Dimensions ........................8
B. Clearances to Combustibles...............9
C. Hearth Pad Requirements ..................9
Section 4: Vent Information
Section 11: Reference Materials
A. Venting Termination Minimum
A. Component Functions.........................38-39
B. Component Locations.........................40
C. Exploded Drawings.............................41-42
D. Service Parts & Accessories...............43-46
E. Service & Maintenance Log................47-48
F. Homeowner’s Log...............................49
G. Warranty Policy...................................50-51
H. Contact Information.............................52
Requirements......................................10
B. Chimney & Exhaust Connection.........11
C. Equivalent Feet of Pipe.......................11
D. Pipe Selection Chart............................12
Section 5: Venting Systems
A. Alcove .................................................13
B. Through the Wall.................................14
C. Vertical into Class A Chimney.............15
D. Through the Wall & Vertical-Exterior...15
E. Vertical-Interior....................................15
F. Masonry ..............................................16
G. Alternate Masonry...............................16
Section 6: Mobile Home Installation............17
Section 7: Appliance Set-Up
A. Leg Leveling System ..........................18
B. Outside Air Kit.....................................18
C. Top Vent Adapter................................19
D. Rear Vent Adapter ..............................19
E. Log Set Placement..............................20
F. Wall Control Thermostat .....................21
Page 3
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Listing and Code Approvals
1
E. BTU & Efficiency Specifications
A. Appliance Certification
Model
Mt. Vernon Pellet Stove AE
Emissions Rating: EPA Compliance
Laboratory
Report No.
Type
OMNI Test Laboratories, Inc.
061-S-68-6
Solid Fuel Room Heater/Pellet Type
*BTU Output:
Efficiency:
14,620 - 60,200
81.4% - 83.6%
Heating Capacity: 2,400 - 3,800 square feet depend-
Standard
ASTM E1509-04, ULC S627-00 and
ULC/ORD-C1482-M1990 Room Heater
Pellet Fuel Burning type and (UM) 84-
HUD, Mobile Home Approved.
Complies with Part 15 of FCC Rules.
Operation is subject to the following
two conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that
may cause undesired operation.
ing on heating zone
Hopper Capacity: 81 lbs
Fuels:
Pellets, Shelled Field Corn, Wheat
and Black Sunflower Seeds
FCC
Shipping Weight:
429 lbs
*BTU output will vary, depending on the type of fuel you
use in your stove. Consult your Quadra-Fire dealer for
best results.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products,
their specifications and/or price without notice.
B. Mobile Home Approved
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is provided. The structural integrity of
the mobile home floor, ceiling, and walls must be maintained.
The appliance must be properly grounded to the frame of
the mobile home and use only listed pellet vent Class “L” or
“PL” connector pipe. A Quadra-Fire Outside Air Kit must be
installed in a mobile home installation.
C. Glass Specifications
This appliance is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
NOTE: This installation must conform with local codes.
In the absence of local codes you must comply with the
ASTM E1509, ULC S627-00, (UM) 84-HUD and ULC/
ORD-C-1482.
D. Electrical Rating
115 VAC, 60 Hz, Start 5 Amps, Run 1.25 Amps
Page 4
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Getting Started
2
Since pellet exhaust can contain ash, soot or sparks, you
must consider the location of:
A
.
Design, Installation & Location Considerations
1. Appliance Location
OT Check building codes prior to installation.
• Windows
• Air Intakes
•
Installation MUST comply with local, regional, state and
national codes and regulations.
• Air Conditioner
• Overhang, soffits, porch roofs, adjacent walls
• Landscaping, vegetation
•
Consult insurance carrier, local building inspector, fire
officials or authorities having jurisdiction over restrictions,
installation inspection and permits.
When locating vent and venting termination, vent above
roof line when possible.
It is a good idea to plan your installation on paper, using
exact measurements for clearances and floor protection,
before actually beginning the installation
Damaged parts could impair safe
operation. Do NOT install damaged, incomplete or substitute
components.
Consideration must be given to:
T O
If burning shelled field corn, you must use ap-
• Safety, convenience, traffic flow
proved venting specifically designed for corn to prevent corro-
sion or degradation. Follow the instructions from the venting
manufacturer.
• Placement of the chimney and chimney connector.
• If you are not using an existing chimney, place the appli-
ance where there will be a clear passage for a factory-
built listed chimney through the ceiling and roof.
OT
Locating the appliance in a location of
considerable air movement can cause intermittent smoke
spillage from appliance. Do not locate appliance near:
• Installing an optional outside air kit would affect the loca-
tion of the vent termination.
•
•
Frequently open doors
Central heat outlets or returns
Recommended Location
A ove pea
Inside heated space
Recommended Location
A ove pea
Marginal Location
Wind loading possi le
Marginal Location
Below pea
Location NOT recommended
Not the highest point of the roof
Wind loading possi le
Location NOT recommended
Too close to tree
Below ad acent structure
Lower roof line
Avoid outside wall
Recommended
Insulated exterior chase
in cooler climates
Windward
Leeward
Multi-level Roofs
Recommended
NOT recommended
Outside Air Inta e
on windward side
Outside Air Inta e
on leeward side
Figure 5.1
Page 5
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
B. Locating Your Appliance & Chimney
E. Negative Pressure
Negative pressure can
cause spillage of combustion fumes and soot.
Location of the appliance and chimney will affect
performance.
•
Install through the warm airspace enclosed by the building
envelope. This helps to produce more draft, especially
during lighting and die-down of the fire.
Negative pressure results from the imbalance of air avail-
able for the appliance to operate properly. It can be stron-
gest in lower levels of the house.
•
•
Penetrate the highest part of the roof. This minimizes the
effects of wind loading.
Causes include:
•
•
•
Exhaust fans (kitchen, bath, etc.)
Range hoods
Locate termination cap away from trees, adjacent
structures, uneven roof lines and other obstructions.
•
•
Minimize the use of chimney offsets.
Combustion air requirements for furnaces, water heaters
and other combustion appliances
Consider the appliance location relative to floor and ceiling
and attic joists.
•
•
•
•
Clothes dryers
•
Take into consideration the termination requirements on
Page 10.
Location of return-air vents to furnace or air conditioning
Imbalances of the HVAC air handling system
Upper level air leaks such as:
- Recessed lighting
CAUTION
•
•
Do NOT connect this unit to a chimney flue servicing
- Attic hatch
another appliance.
- Duct leaks
Do NOT connect to any air distribution duct or system.
To minimize the effects of negative air pressure:
•
•
•
•
Install the outside air kit with the intake facing prevailing
winds during the heating season
C. Wall Control Thermostat
The wall control’s location will have some affect on the
appliance’s operation.
Ensure adequate outdoor air for all combustion appliances
and exhaust equipment
• When located close to the appliance, it may require a
slightly higher temperature setting to keep the rest of
the house comfortable.
Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the appliance
Avoid installing the appliance near doors, walkways or
small isolated spaces
• When located in an adjacent room or on a different floor
level, you will notice higher temperatures near the ap-
pliance.
•
•
•
Recessed lighting should be a “sealed can” design
Attic hatches weather stripped or sealed
T O
T
Attic mounted duct work and air handler joints and seams
taped or sealed
D. Draft
Draft is the pressure difference needed to vent appliances
successfully. When an appliance is drafting successfully, all
combustion byproducts are exiting the home through the
chimney.
Considerations for successful draft include:
•
•
Preventing negative pressure
Location of appliance and chimney
OT
Hearth & Home Technologies assumes no
responsibility for the improper performance of the chimney
system caused by:
•
•
•
•
Inadequate draft due to environmental conditions
Downdrafts
Tight sealing construction of the structure
Mechanical exhausting devices
Page 6
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
G. Tools And Supplies Needed
F. Fire Safety
To provide reasonable fire safety, the following should be
given serious consideration:
Tools and building supplies normally required
for installation, unless installing into an existing
masonry fireplace:
• Install at least one smoke detector on each floor of your
home.
Reciprocating Saw
Channel Locks
Hammer
Safety Glasses
• Locate smoke detector away from the heating appliance
and close to the sleeping areas.
Framing Square
Electric Drill & Bits (1/4”)
1/4” Self-Tapping Screws
• Follow the smoke detector manufacturer’s placement and
installation instructions and maintain regularly.
Phillips Screwdriver
Tape Measure
Plumb Line
May also need:
Vent Support Straps
Venting Paint
• Conveniently locate a Class A fire extinguisher to contend
with small fires.
Level
Framing Material
Hi-temp Caulking Material
Gloves
•
In the event of a hopper fire:
• Evacute the house immediately.
• Notify fire department.
H. Inspect Appliance & Components and
Pre-Use Check List
WARNING
1.
Place the appliance in a location near the
final installation area and follow the proce-
dures below:
Fire Risk.
•
Do not operate appliance before reading
2.
Open the appliance and remove all the parts
and articles packed inside the Component
Pack.
and understanding operating instructions.
Failure to operate appliance properly may
cause a house fire.
Inspect all the parts and glass for shipping
damage. Contact your dealer if any irregulari-
ties are noticed.
Remove rubber band from ash pan installed for
shipping purposes only.
3.
All safety warnings have been read and fol-
lowed.
This Owner’s Manual has been read.
Floor protection requirements have been met.
Venting is properly installed.
The proper clearances from the appliance and
chimney to combustible materials have been
met.
The masonry chimney is inspected by a profes-
sional and is clean, or the factory built metal
chimney is installed according to the manufac-
turer’s instructions and clearances.
WARNING
4.
5.
6.
7.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
•
•
•
Installation and use of any damaged appliance.
Modification of the appliance.
Installation other than as instructed by Hearth & Home
Technologies.
Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Operating appliance without fully assembling all
components.
Operating appliance without legs attached (if supplied with
unit).
•
•
•
•
8.
9.
The chimney meets the required minimum
height.
Do NOT Overfire
10.
11.
All labels have been removed from the glass
door.
Plated surfaces have been wiped clean, if
applicable.
Or any such action that may cause a fire hazard.
12.
13.
14.
Wall Control Thermostat has been installed.
A power outlet is available nearby.
Agood quality surge protectory is highly recom-
mended to protect the electronics.
Page 7
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Dimensions and Clearances
3
A. Appliance Dimensions
14-1/16 in.
(357mm)
5-13/16 in.
(147mm)
3-13/16 in.
(97mm)
2-9/16 in.
(65mm)
C
L
31-1/6 in.
(788mm)
29-3/6 in.
(741mm)
Figure 8.1 - Top View with Top Vent Adapter and 3 to
6 in (76-152mm) Adapter
Figure 8.2 - Side View with Top Vent Adapter and
3 to 6 in (76-152mm) Offset Adapter.
10-3/8 in.
(264mm)
C
L
Figure 8.3 - Top View
29-1/16 in. (738mm)
26-7/8 in. (683mm)
18-1/2 in. (470mm)
28-1/8 in. (714mm)
32-5/16 in.
(821mm)
C
L
19-9/16 in.
(497mm)
28-7/16 in.
(722mm)
20 in.
(508mm)
Figure 8.4 - Front View
Page 8
Figure 8.5 - Side View
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
C. Hearth Pad Requirements (UL and ULC)
B. Clearances to Combustibles (UL and ULC)
Use a non-combustible floor protector, extending beneath
appliance and to the front, sides and rear as indicated.
Measure front distance “M” from the surface of the glass
A
C
door.
L*
B
C
K
K
Straight Back Against Wall
Inches
Millimeters
51
A
B
Back Wall to Appliance
Side Wall to Appliance
2
6
152
M
Corner Installation
Walls to Appliance
Inches
2
Millimeters
51
Hearth Pad Requirements
Inches
Millimeters
C
K
L*
M
Sides
Back
Front
2
2
6
51
51
152
Installations with:
3 to 3 inch Top Vent Adapter and
3 to 6 inch Offset Adapter Kit
*L Exception for Horizontal Installations:
USA INSTALLATIONS: A non-combustible floor protec-
tion is recommended extending beneath the flue pipe
when installed with horizontal venting or under the Top
Vent Adapter with vertical installation.
G
F
D
G
CANADA INSTALLATIONS:
A
non-combustible floor
protection extending beneath the flue pipe is required
with horizontal venting or under the Top Vent Adapter with
vertical installation.
E
Vertical Installation
Inches
Millimeters
D
E
F
Back Wall to Flue Pipe
3
6
8
76
Side Wall to Appliance
Back Wall to Appliance
152
203
Corner Installation
Inches
3
Millimeters
76
G
Side Wall to Flue Pipe
Alcove Installation
Inches
43
Millimeters
1092
Minimum Alcove Height
Minimum Alcove Side Wall
Minimum Alcove Width
Maximum Alcove Depth
Must extend 2 inches (51mm) beyond each
side of pipe (shaded area)
6
152
40
1016
36
914
WARNING
NOTE:
Fire Risk.
•
Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
Comply with all minimum clearances to
combustibles as specified.
•
•
Illustrations/diagrams are not drawn to scale.
Actual installation may vary due to individual design
preference.
Failure to comply may cause house fire.
Page 9
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Vent Information
4
A. Venting Termination Minimum Requirements
V
N
N
N
Electrical
Service
V
V
Inside Corner
N
V
G
V
A
H
D
P
E
O
L
C
B
FIXED
CLOSED
FIXED
CLOSED
V
OPEN
V
OPEN
B
G
F
M
V
V
I
X
V
A
B
B
J or K
Figure 10.1
V
G
Termination Cap
X
Restricted Area
Air Supply Inlet
Gas Meter
All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below.
A
B
12 in.
Above Finish Grade (the grade surface
must be a non-combustible material
24 in.
Above grass, top of plants, wood or any other com-
bustible
12 in.
48 in. no OAK
Open door or window: below or to the side
12 in.
36 in. no OAK ance
Clearance from any forced air intake of other appli-
B
C
12 in.
6 in.
Open door or window: above
12 in.
15 in.
Clearance horizontally from combustible wall
Permanently closed window: above, below
or to the side
Vented directly through a wall, minimum length of
horizontal pipe
D
18 in.
36 in. no OAK
Vertical clearance to a ventilated soffit
located above the terminal within a hori-
zontal distance of 2 ft from the center-line
of the terminal
6 in. horizontal Minimum horizontal or vertical terminations must
12 in. vertical
protrude from wall
OT
E
F
12 in.
12 in.
12 in.
36 in.
Clearance to unventilated soffit
Clearance to outside corner
Clearance to inside corner
Do NOT Terminate Vent:
•
In any location that will allow flue gases or soot from enter-
ing or staining the building
G
H
Above gas meter/regulator measured from
horizontal center-line of regulator
•
In any location which could create a nuisance or hazard
•
In any enclosed or semi-enclosed area such as a carport,
garage, attic, crawl space, under a sun deck or porch,
narrow walkway
I
36 in. USA
Clearance to service regulator vent outlet
72 in. Canada
J
12 in.
48 in. no OAK
Clearance to non-mechanical air supply
inlet to the building or the combustions air
inlet to any other appliance
•
Closely fenced area, or any location that can build up
a concentration of fumes such as a stairwell, covered
breezeway, etc.
K
L
10 ft horizontal Clearance to mechanical air supply
3 ft vertical
7 ft.
Above paved sidewalk, paved driveway
located on public property
OT
Termination must exhaust above air inlet elevation.
M
N
12 in.
Under an open veranda, porch, deck or
balcony
•
It is recommended that at least 60 inches (1524mm) of
vertical pipe be installed when appliance is vented directly
through a wall. This will create a natural draft, which will
help prevent the possibility of smoke or odor venting into
the home during a power outage.
See Note
below*
Electric service: above, below or to the
side (location must not obstruct or interfere
with access)
O
P
24 in.
12 in.
Adjacent building, fences and protruding
parts of the structure
•
•
It will also keep exhaust from causing a nuisance or hazard
by exposing people or shrubs to high temperatures.
Clearance above roof line for vertical
terminations
The safest and preferred venting method is to extend the
vent vertically through the roof or above the roof.
*NOTE: Consult local building, fire officials or authorities having jurisdic-
tion. Local codes or regulations may require different clearances.
Page 10
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
B. Chimney and Exhaust Connection
WARNING
1. Chimney & Connector: Use 3 or 4 inch (76-102mm)
diameter type "L" or "PL" venting system. It can be vented
vertically or horizontally.
Fire Risk
•
Only LISTED venting components may be
used.
NO OTHER vent components may be used.
2. Mobile Home: Approved for all Listed pellet vent. If using
the 3 inch (76mm) vertical Top Vent Adapter Kit or the 3
to 6 inch (76-152mm) Top Vent OffsetAdapter, use Listed
double wall flue connector. A Quadra-Fire Outside Air Kit
must be used with manufactured home installations.
•
Substitute or damaged vent components may
impair safe operation.
3. Residential: The 3 inch (76mm) vertical Top VentAdapter
Kit and the 3 to 6 inch (76-152mm) Top Vent OffsetAdapter
are tested to use 24 gauge single wall flue connector or
Listed double wall flue connector to Class A Listed metal
chimneys, or masonry chimneys meeting International
Residential Code standards for solid fuel appliances.
WARNING
Vent surfaces get HOT, can cause burns
if touched. Non-combustible shielding or
guards may be required.
4. INSTALL VENT AT CLEARANCES SPECIFIED BY THE
VENT MANUFACTURER.
5. Secure exhaust venting system to the appliance with at
least 3 screws. Also secure all connector pipe joints with
at least 3 screws through each joint.
WARNING
NOTE: All pipe must be welded seam pipe whenever
possible. Seal pipe joints with high temperature silicone
(500°F [260°C] minimum rated only).
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this ap-
pliance. For assistance or additional information consult a
qualified installer, service agency or your dealer.
NOTE: If burning shelled field corn, you must use
approved venting specifically designed for corn. Follow
the instructions from the venting manufacturer.
C. Equivalent Feet of Pipe
The table below can help you calculate the equivalent feet
of pipe which is a method used to determine pellet vent size.
See Figure 11.1.
Example of 3 Elbow-Rear Vent Termination Calculation
Pellet Venting
Component
# of
Feet of Multiplied Equivalent
Components
Equivalent Feet
Elbows
Pipe
By
X
Feet
5
o
2 ft.
90 Elbow or Tee
3
15
o
45 Elbow
X
3
Horizontal Pipe
Vertical Pipe
7
2
X
X
1
0.5
7
1
3 ft.
Total Equivalent Feet
23
2 ft.
Note: This is a generic example and is not
intended to represent any specific fuel type.
2 ft.
Figure 11.1
September 1, 2008
Page 11
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
D. Pipe Selection Chart
WARNING
The chart will help you in determining proper venting size
according to the equivalent feet of pipe calculated in Vent
Termination Calculation Table and the altitude above sea
level of this installation. See Figure 12.1.
Fire Risk.
Do NOT pack insulation or other
combustibles between firestops.
•
ALWAYS maintain specified clearances
around venting and firestop systems.
Locate the calculated equivalent feet of pipe on the vertical
left side of the chart. Move to the right horizontally on the
chart until you reach your altitude above sea level.
•
Install firestops as specified.
Failure to keep insulation or other material
away from vent pipe may cause fire.
If you fall below the diagonal line, 3 or 4 inch (76 to 102mm)
pipe may be used. If it is anywhere above the diagonal line,
a 4 inch (102mm) diameter pipe is required.
The chart reveals that a 90° elbow is 5 times as restrictive
to the flow of exhaust gases under positive pressure as one
foot of horizontal pipe, and a foot of horizontal pipe is twice
as restrictive as a foot of vertical pipe.
30
4 in. (102mm) Diameter Pipe Only
Example 1
20
Equivalent Pipe
Length In Feet
Example 2
10
3 in. or 4 in. (76mm or 102mm) Diameter Pipe
0
1
2
3
4
5
6
7
8
9
10
ALTITUDE IN THOUSANDS OF FEET
Figure 12.1
Example 1: If the equivalent length of pipe is 23 feet with altitude of
8,000 feet you must use 4 inch (102mm) diameter type “L” or “PL”
vent.
Example 2: If the equivalent length of pipe is 12 feet with altitude of
6,000 feet you may use 3 or 4 inch (76 to 102mm) diameter type “L”
or “PL” vent
Page 12
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Venting Systems
5
A. Alcove
A
C
D
B
Figure 13.1
Minimum*
Maximum
Inches Millimeters Inches Millimeters
Height
43
40
n/a
6
1092
1016
n/a
n/a
n/a
36
n/a
n/a
914
n/a
A
B
C
D
Width
Depth
To Side Wall
152
n/a
*All minimums listed are to a combustible surface.
NOTE:
•
Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
Illustrations/diagrams are not drawn to scale.
Actual installation may vary due to individual design
preference.
•
•
Page 13
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
B. Through The Wall
Horizontal termination cap must be a minimum of 6 inches.
(152mm) from the wall. Approved for mobile home installa-
tions. Must use 3 or 4 inch (76-102mm) “L” or “PL” Listed
pellet venting or Listed double wall pipe and a Quadra-Fire
Outside Air Kit in mobile homes.
NOTE:
In Canada, where passage through a wall or partition of
combustible construction is desired, the installation shall
conform to CAN/CSA-B365
2 in.
(51mm)
Straight Out
Horizontal
Termination
Cap
Minimum
Wall
Thimble
6 in.
(152mm)
Minimum
From Glass
6 in.
(152mm)
Minimum
Non-combustible Hearth Pad
Figure 14.1
Illustration shows venting going in both directions.
Choose which one is best for your installation.
45 Degree
6 in. (152mm)
Minimum
6 in. (152mm)
Minimum
Wall
Thimble
2 in. (51mm)
Minimum
2 in.
(51mm)
Minimum
Figure 14.2
Page 14
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
C. Vertical into Existing Class A Chimney
We recommend a minimum of 60 inches
(1524mm) vertical, however above the eave
is preferred.
Rain Cap
All three installations are approved for mobile
home installations. Must use 3 or 4 inch (76
to 102mm) “L” or “PL” Listed pellet venting or
Listed double wall pipe and Quadra-Fire Out-
sideAir Kit in mobile homes. Single wall pipe
is approved for residential installations only.
Flashing
12 in. (305mm) Minimum
Firestop
*NOTE: Clearance to combustibles are for
standard pellet pipe. If pellet pipe manufac-
turer allows reduced clearances to their pipe,
reduced clearances are allowed.
6 in. (152mm) Class A
Chimney Connector
Adapter
Ceiling Support
3 in. (76mm) Min.
3 to 6 in. (76-152mm)
Offset Adapter
6 in.
(152mm)
Min.
3 to 3 in.
(76-76mm)
Top Vent Kit
Clean-out Cover
Non-combustible Hearth Pad
Figure 15.1
E. Vertical - Interior - Typical Installation
D. Through The Wall & Vertical - Exterior
Rain
Cap
Rain Cap
12 in.
(305mm)
minimum
Flashing
12 in.
Flashing
(305mm)
Minimum
Firestop
Support
2 in. (51mm) minimum
Bracket
every 60 in.
(1524mm)
6 in. (152mm)
minimum
Wall Thimble
Tee
3 in. (76mm)Min.
6 in.
(152mm)
Min.
3 in. to 3 in.
(76-76mm)
Top Vent Kit
Clean-out
Cover
Clean-out Cover
Non-combustible Hearth Pad
Non-combustible Hearth Pad
Figure 15.3
Figure 15.2
Page 15
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
WARNING
Fire Risk.
Inspection of Chimney:
•
•
•
Masonry chimney must be in good condition.
Meets minimum standard of NFPA 211
Factory-built chimney must be 6 inch (152mm) UL103 HT.
F. Masonry
Fireclay flue
liner with airspace
Concrete Cap
Flashing
1 in. (25mm) clearance
with firestop
1 in. (25mm) clearance
3 in. (76mm) minimum to
combustible material
6 in. (152mm)
minimum
Sheathing
Clean-out cover
Airtight
Clean-out Door
Non-combustible Hearth Pad
Figure 16.1
G. Alternate Masonry
Fireclay Flue Liner
with airspace
Concrete Cap
Flashing
1 in. (25mm) clearance
with firestop
1 in. (25mm) clearance
2 in. (51mm) minimum to
combustible material
6 in. (152mm)
minimum
Sheathing
Airtight clean-out door
Non-combustible Hearth Pad
Figure 16.2
Page 16
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Mobile Home Installation
6
You must use a Quadra-Fire Outside Air Kit
for installation in a mobile home.
CAUTION
Maintain structural integrity of mobile home:
1. An outside air inlet must be provided for the combustion
air and must remain clear of leaves, debris, ice and/or
snow. It must be unrestricted while the appliance is
in use to prevent room air starvation which causes
smoke spillage. Smoke spillage can also set off smoke
alarms.
•
Floor, wall, ceiling and/or roof.
Do NOT cut through:
•
•
Floor joist, wall, studs or ceiling trusses.
Any supporting material that would affect the structural
integrity.
2. The combustion air duct system must be made of
metal. It must permit zero clearance to combustible
construction and prevent material from dropping into
the inlet or into the area beneath the dwelling and
contain a rodent screen.
Spark Arrestor Cap
3. The appliance must be secured to the mobile home
structure by bolting it to the floor (using lag bolts).
Use the same holes that secured the appliance to the
shipping pallet.
Storm Collar
Roof Flashing
4. The appliance must be grounded with #8 solid copper
grounding wire or equivalent, terminated at each end
with an NEC approved grounding device.
5. Refer to Clearances to Combustibles and floor protec-
tion requirements on page 9 for listings to combustibles
and appropriate chimney systems.
Joist Shield/Firestop
Approved Class L
or PL Pellet Vent
6. Use silicone to create an effective vapor barrier at
the location where the chimney or other component
penetrates to the the exterior of the structure.
7. Follow the chimney manufacturer’s instructions when
installing the vent system for use in a mobile home.
8. Installation shall be in accordance with the Manufactur-
ers Home & Safety Standard (HUD) CFR 3280, Part
24.
Figure 17.1
WARNING
Installation must comply with Manufactured Home and
Safety Standard (HUD), CFR 3280, Part 24.
WARNING
Never install in a sleeping room.
Page 17
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Appliance Set-Up
7
B. Outside Air Kit Instructions
A. Leg Leveling System
1. Thread Allen bolts through nuts until flush. Figure 18.1.
The Allen bolts and nuts are included in the component
pack inside the appliance firebox.
CAUTION
Never draw outside combustion air from:
•
•
Wall, floor or ceiling cavity
Enclosed space such as an attic or garage
2. Slide assembled nuts and bolts into slots on legs with
the nuts on the bottom. Figure 18.2. Use a 5/32 in.
(3.96mm) Allen wrench to adjust legs up and down to
desired level. Figure 18.3.
Included in Kit: 2 wire ties, 1 collar assembly,
1 termination cap assembly, 1 trim ring, fasteners.
NOTE: 3 INCH ALUMINUM FLEX PIPE NOT INCLUDED.
Tools Needed: Phillips head screw driver; wire cutters;
hole saw or jig saw.
1. Measure distance from floor to air vent opening in appli-
ance and mark location on wall.
Use saw to cut opening in wall. Cut a 3-1/2 to 4 inch
(89-102mm) opening on inside wall and a 4 to 4-1/2
inch (102-114mm) opening on outside of house.
Figure 18.1
2. Use wire tie to secure flex pipe to collar assembly.
3. Slide trim ring over flex pipe and run pipe through wall.
4. Attach flex pipe (not supplied) to outside termination
cap with second wire tie.
5. Secure termination cap to outside surface.
6. Secure trim ring to interior wall.
Figure 18.2
Termination Cap
3 inch Aluminum
Flex Pipe
(not included)
Wire
Tie
Trim Ring
Figure 18.3 - Bolt fully extended
Wire Tie
Collar
Figure 18.4
Page 18
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
C. Top Vent Adapter Installation
3 to 3 inch Top Vent Adapter
3 to 6 inch Top Vent Offset Adapter
Installing the Top Vent Adapter
1. Put a layer of high temperature silicone on the
3
inch (76mm) exhaust outlet. Figure 19.1.
Align slot holes on the adapter
to holes on the a k of the nit
2. Slide the top vent adapter onto the rear exhaust
outlet and adjust the assembly to a vertical position
until the top of the flue outlet is centered and is in
a level position. Figure 19.1.
3. Align slot on left of adapter with hole in the back of
the unit and secure with screw. You may drill out the
hole using #26 drill bit provided but only if needed.
Figure 19.2.
4. Install the 5 mounting screws, 3 on the left and 2
on the right.
Figure 19.2
5. Drill 2 holes with #26 drill bit through the rear
exhaust outlet using the 2 holes already in the short
horizontal pipe in the top vent adapter as a guide.
Install the screws. Figure 19.2.
D. Rear Vent and Rear Vent to Top Vent
Adapter Installation
6. Install the vent pipe into the top vent adapter (be
sure to silicone all joints). To use an existing 6
inch (152mm) vent system, install the 3 to 6 in (76-
152mm) offset adapter before installing vent pipe.
7. To clean top vent adapter, open clean-out cover
and remove any debris build-up. Figure 19.2.
Clean-Out Cover
Figure 19.3 - Rear Vent Adapter
3 in. to 6 in.
Offset Adapter
Clean-Out Cover
3 in. to 3 in. Top
Vent Adapter
Drill Hole, 1
on each side
Figure 19.4 - Rear to Top Vent Adapter - 90o
Silicone Rear
Exhaust Outlet
Clean-Out
Cover
1. Put a layer of high temperature silicone on the 3 inch
(76mm) exhaust outlet. Figure 18.1.
Figure 19.1
2. Slide the adapter onto the rear exhaust outlet and
adjust the assembly to the appropriate position.
3. Install the vent pipe into the adapter (be sure to
silicone all joints)
Page 19
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
E. Optional Log Set Placement Instructions
2 PIECE LOG SET INSTALLATION
1. Place the left log as shown. There are 2 indentations in
the bottom of the log to fit over the screw heads in the
firebox. Figures 20.1 and 20.2.
2. Place the right log in front of the 2 screw heads in the
firebox. Figures 20.3 & 20.4.
Right Log
CAUTION
Logs are FRAGILE. Use extreme care when handling or
cleaning logs.
Log rests in front of screws
Figure 20.3
Left Log
Log fits over screws
Figure 20.1
Figure 20.4
Log has indentations on the
bottom to fit over the screw heads.
NOTICE:
Due to the abrasive nature of a pellet appliance fire, the
logs are not covered under warranty. Any placement vari-
ation other than shown here can cause excessive heat
and shall void the appliance warranty.
Figure 20.2
Page 20
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
F. Wall Control Thermostat Installation
1. When mounting the wall control thermostat on the wall,
be sure to follow your thermostat wall control’s instal-
lation instructions carefully.
all Control hermostat ires
Atta h to Center S re
s
reen
hite Red
NOTE: The wall control thermostat should be
mounted on an inside wall and not in direct line
with the appliance convection air.
NOTE: If the wall control thermostat is located too
close to the appliance, you may need to set the
temperature setting slightly higher to maintain the
desired temperature in your home.
volt Po er nlet for
optional atter a k
o shold Po er
Cord nlet
2. There is a 5 screw terminal block located on the back
lower left corner of the appliance directly above the
power cord inlet.
p
The center 3 screws are for the wall control thermostat
wires and the 2 outer screws are mounting screw and
should not have wires attached to them.
The thermostat wires are color coded. The green wire
is on the left, the white in the middle and the red on the
right.
CAUTION
Shock hazard.
•
•
Do NOT remove grounding prong from plug.
Plug directly into properly grounded 3 prong
receptacle.
Route cord away from appliance.
Do NOT route cord under or in front of appliance.
•
•
Figure 21.2
Top
Red Wire
Green Wire
White Wire
Bottom
Figure 21.1 - Back Side of Wall Control with
Cover Off
Page 21
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Operating Instructions
8
2. Other Fuels
CAUTION
This appliance has been tested and approved by Hearth &
Home Technologies for shelled field corn, wheat and black
oil sunflower seeds.
Tested and approved for wood pellets, shelled field
corn, wheat and black oil sunflower seeds. Burning
of any other type of fuel voids your warranty.
When purchasing corn or wheat to burn in your appliance,
read the ingredient label very carefully. Do NOT purchase
fuel that contains any additives such as oils (i.e. soybean
oil) and meals as it will result in poor unit performance. If
you are buying corn or wheat the only ingredient that should
be listed is corn or wheat.
A. Fuel Size, Material and Storage
1. Wood Pellets
Wood pellets are made from sawdust or wood by-products. If
the source material is hardwood, they can have a higher mineral
content, creating more ash. Fuels containing bark will also have
higher ash content.
Shelled field corn must be 15% or less moisture content. The
corn must be clean and free from debris. Never burn corn
straight from the field. Stalk parts, excessive fines and cob
remnants, etc. will clog the auger mechanism. Corn with
excessive grain dust must be screened by sifting with 3/16
inch mesh screening.
Minerals and other non-combustible materials such as sand
will turn into a hard, glass-like substance called a clinker when
heated to the extreme temperatures our firepot reaches. This
is what forms clinkers in the bottom of the firepot. Trees from
different areas will vary in mineral content. That is why some
fuels produce more clinkers than others.
WARNING
Risk of Chemical Poisoning.
•
Do Not burn treated seed corn
Pellets are manufactured in either 1/4 inch or 5/16 inch (6-8mm)
diameter and should be no more than 1-1/2 inches (38mm)
in length. Pellet lengths may even vary by lot from the same
manufacturer which is why the feed rate may need to be adjusted
occasionally. If you burn pellets longer than 1-1/2 inches
(38mm) you may have an inconsistent fuel feed rate and/or
missed ignitions.
• Chemical pesticides are harmful or fatal if
swallowed
• Burning treated seed corn will void your
warranty
Do not burn treated seed corn in your appliance. Seed corn
is treated with chemical pesticides that are harmful or fatal if
swallowed; therefore, seed corn is dangerous to have in the
house, expecially where children can reach it. Burning treated
seed corn in your appliane will void your warranty and will
destroy the exhaust system on the unit.
Pellet fuel quality can greatly fluctuate. The Advanced Energy
(AE) appliance has been designed to burn a wide variety of fuels,
giving you the choice to use the fuel that is most economical in
your region. Premium wood pellets have the lowest ash content,
under 1%. Standard grade pellet, high ash pellets, corn and
other biomass fuels all have higher ash content.
When changing to a different fuel, be sure to empty the hopper
of the previous fuel and vacuum the hopper before you fill it
with the new fuel. Make the appropriate selection on the FUEL
SELECTION screen on the thermostat wall control. The burn
rate, BTU content and heat output will all vary depending on
fuel selected. See Figure 23.3 on page 23.
The higher the ash content, the more often the ash pan will need
to be emptied. Premium wood pellets will produce the least ash
and tends to produce the highest heat output.
Pellets made from hardwoods (i.e. oak) have a higher ash content
than pellets made from softwoods (i.e. pine). The hardwood
pellets may require more air to burn properly so make sure you
have the wall control on the correct setting.
3. Storage
If you are burning a higher ash fuel and your firepot and ash pan
are filling quickly, set the wall control on “Utility Pellet” and the
auto-clean system will empty the firepot more frequently.
Wood pellets should be left in their original sealed bag until
using. This will prevent moisture absorption.
Shelled corn, wheat or sunflower seeds should be stored in
a tight container where it will not absorb moisture from damp
or wet floors. This will also prevent rodents from becoming
a problem.
Always burn dry fuel. Burning fuel with high moisture content
takes heat from the fuel and tends to cool the appliance,
robbing heat from your home. Damp pellet fuel can clog the
feed system.
Do not store any pellet fuel within the clearance requirements
or in an area that would hinder routine cleaning and
maintenance.
We recommend that you buy fuel in multi-ton lots whenever
possible. However, we do recommend trying various brands
before purchasing multi-ton lots to ensure your satisfaction.
Page 22
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
C. Before Your First Fire
1. First, make sure your appliance has been properly
installed and that all safety requirements have been met.
Pay particular attention to the fire protection, venting and
wall control thermostat installation instructions.
B. General Operating Information
See Wall Control Thermostat Manual
for detailed operating instructions.
2. Double check that the ash pan and firebox are empty
and then close the front door.
1. Wall Control Thermostat - Automatic Setting
CAUTION
The appliance is like most modern furnaces; when the
wall control thermostat calls for heat, your appliance will
automatically light and deliver heat. When the room is up to
temperature and the wall control is satisfied the appliance
will shut down.
Tip of thermocouple must be in contact with the inside
end of the thermocouple cover.
Missed ignitions can occur.
In the automatic setting the heat output level is controlled
by the wall control. Select “Automatic” on the AUTO/
MANUAL screen. Figure 23.1.
D. Starting Your First Fire
1. Fuel Selection
To start your first fire, you must select the appropriate fuel on
the FUEL SELECTION screen on the thermostat wall control
to match the fuel you have chosen to burn.
If the proper fuel is not selected your appliance will not operate
properly. For example, if you have selected wood pellets and
you are burning corn, the appliance may not light, may go
out or overfeed. Figure 23.3.
Automatic
Manual
Off
2. Comfort Level Selection
Once your fuel is selected, select the temperature at the
desired setting on the SET COMFORT LEVEL screen.
Figure 23.4.
Figure 23.1
2. Wall Control Thermostat - Manual Setting
3. Automatic or Manual Setting
When you select “Manual” on the AUTO/MANUAL screen
the appliance will still automatically turn on and off
according to the temperature setting. However, you will
be able to manually control the heat output levels. Adjust
the heat output levels by using the HEAT OUTPUT LEVEL
screen.
The automatic setting will control the heat output based on
the comfort level selection. The manual setting allows you
to manually control the heat output settings. See page 24,
Ignition Cycles.
NOTE: See the Wall Control Thermostat manual for
detailed instructions.
FUEL SELECTION
Corn
Utility Pellet
Softwood Pellet
Sunflower Seeds
Medium
Wheat
Hardwood Pellet
Figure 23.2
DONE
SELECT
Figure 23.3
3. Auto-Clean Firepot System
Your appliance is equipped with an automatic firepot
cleaning system that will change the frequency of cleaning
based on the fuel being burned.
The auto-clean system will clean itself immediately on initial
plug in. If there is a power outage, as soon as power is
restored it will automatically clean itself.
Figure 23.4
Page 23
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
E. Fire Characteristics and Flame Height
Adjustment
G. Ignition Cycles
The Advanced Energy engine is controlled by the digital wall
control. The digital display on the wall control will tell you what
your appliance is doing in the upper left corner, above the line
A properly adjusted fire with the heat output on HIGH
has an active flame pattern that extends out of the firepot
approximately 8 inches (203mm).
Every time the thermostat calls for heat, the appliance steps
through five cycles:
If the fire has tall flames with black tails and seems some-
what lazy, the flame height will need to be reduced. If
the fire is not 8 inches (203mm) tall, the flame height will
need to be increased. A medium or low setting will give
a shorter flame.
1. Ignition cycle
2. Soft-start cycle
3. Heating cycle
4. Shut down cycle
5. Cleaning cycle
The flame will rise and fall somewhat. This is normal.
With your appliance in Manual mode and the heat output
level set to HIGH adjust the flame height using the
FLAME HEIGHT ADJUST screen on the thermostat wall
control. Figure 24.1.
The duration and characteristics of these cycles may be differ-
ent with each type of fuel selected.
1. Start-Up
During this cycle:
•
The igniter turns on for 90 seconds to heat up the air in
the firepot
•
•
•
The combustion blower starts
Vacuum switch comes on
Feed motor turns on adding fuel to the firepot and the
appliance waits for the fire to start
The duration of start-up depends on the type and quality of fuel
used. It is normal to see some smoke during the ignition pro-
cess as moisture evaporates and the fuel lights. The smoke
will stop once the fire starts.
Figure 24.1
F. Battery Back-up System (Optional)
The appliance has been designed to operate on an optional
battery back-up system. If you have frequent power
outages in your region, hook the appliance up to a 12 volt
battery and it will automatically switch to battery power in
the event of a power failure. There will be a battery icon
that appears on your wall control to let you know you are
now operating on battery power.
If you are lighting your appliance for the first time the feed tube
is empty and it can take some time to fill it with fuel before you
will see a fire. To speed up this process, put a handful of fuel
in the firepot. You can also do this when you have run your
hopper dry.
2. SS-Low / SS-Med (Slow-Start Low, Slow-Start Medium)
Once you are operating on battery power, you must
manually light the fire in the appliance as it will no longer
automatically light. Use only approved fire starting gel to
start the fire. The high burn rate is no longer available
on battery back-up as each level drops down one level.
Once the fire is lit, the appliance moves into the low soft-start
cycle as it continues to build the fire. In this cycle, more fuel
will be added. As the fire builds, the appliance will change to
medium soft-start mode and the heating cycle begins.
For example; the high burn becomes medium high burn 3. Auto / Man - L, ML, M, MH, H
and so on.
There are two choices in the Automatic / Manual menu of how
We recommend a 12 volt deep cycle battery, (i.e., marine or your appliance will operate.
RV type). If the battery charge falls below 10 volt it can no
longer sustain the appliance operation and the appliance
will shut down. A12 volt battery cable is available through
your local dealer.
In Automatic Mode, the wall control will turn the heat output
level up or down depending on how far the room temperature
is from the desired temperature. The digital display will read
AUTO:M as an example of automatic, medium level.
As the room temperature approaches the desired tempera-
ture, the appliance will turn down to lower settings. When you
change the appliance to Manual, set the heat output setting
from the main screen. The right bottom button will read HEAT
OUTPUT.
CAUTION
• Hook up to battery terminals BEFORE you
plug battery into the appliance.
• Damage to internal electronic components
may occur.
Page 24
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
3. Auto / Man - L, ML, M, MH, H (Cont’d)
You can operate the appliance from any of the 5 levels. On
the lowest level, the appliance will stay on longer, burn less
fuel per hour, but will take longer to bring the home up to
your desired temperature. On the highest setting, the appli-
ance will burn more fuel per hour, but bring your home up to
temperature more quickly.
WARNING
Fire Risk
Do NOT operate appliance:
•
•
With appliance door open.
With Firepot floor open.
Do NOT store fuel:
Regardless of the heat output level, when the home reaches
your set temperature, the appliance will go into the shut
down cycle. In Manual mode heat output does not change.
Turn to OFF to stop operation.
•
•
Closer than required clearances to com-
bustibles to appliance.
Within space required for loading or ash
removal.
4. Shutdown
Once your home has reached your set temperature, the
appliance will stop feeding fuel and allow the fire to dimin-
ish. The convection blower will continue to run until the
appliance cools to appropriate temperature and will go into
the auto-clean cycle.
WARNING
Fire Risk
Keep combustible materials, gasoline
and other flammable vapors and liquids
clear of appliance.
5. Auto-Clean
The firepot auto-clean system will cycle when the appliance
is first plugged in:
•
•
Do NOT store flammable materials in the appliance’s
vicinity.
• When the house reaches temperature and the appli-
ance shuts down.
Do NOT use gasoline, lantern fuel, kerosene, charcoal
lighter fluid or similar liquids to start or “freshen up” a
fire in this heater.
Keep all such liquids well away from the heater while it
is in use.
Combustible materials may ignite.
• At prescribed intervals, depending on the type of fuel
selected.
•
•
If your appliance is running and the auto-clean cycle is initi-
ated, the appliance will revert to shut down cycle.
The floor of the firepot will open and deposit the ash into the
ash pan. It takes approximately 2 minutes to complete the
auto-clean cycle. The floor will then shut, and if the thermo-
stat is still calling for heat, the fire will start again, continuing
the heating process.
During this auto-clean cycle, the convection blower will con-
tinue to run.
Additional Screen Messages:
READY It is telling you that the home is up to temperature
and does not need any heat.
- - - - - The screen will show 5 dashes when the wall
control and the control board are NOT communicating with
each other. Check that the wiring on the thermostat is prop-
erly connected.
MAINTENANCE BURN The maintenance burn is to keep
the system from shutting down when operating on battery
backup. The appliance will not automatically re-light in
manual mode.
OFF The AUTO/MANUAL SETTING screen has been set
to OFF. Set the appliance to OFF when performing periodic
maintenance to prevent an unexpected startup.
Page 25
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
H. Quick Start Guide
NOTICE: Any button pressed will turn on the backlight. Wall control will automati-
cally revert back to the starting screen if there is no activity for 15 seconds; except
for the “CONFIRM FUEL CHANGE” screen.
CHOOSING FUEL TYPE
CHOOSING TEMP UNIT:
°F or °C
ttons
P
R
A
R
A
P
Up
Set at
Set at
Room
Temp
P
R
A
Down
MENU
HEAT OUTPUT
Set at
MENU
Function Buttons
1. At the starting screen, press “MENU”
button once or twice until “MENU”
screen appears.
MENU
Wall Control for Reference
1. At the starting screen, press “MENU”
button once or twice until “MENU”
screen appears.
MENU
TURNING ON APPLIANCE
Set Comfort Level
A to/ an al/ ff
Fuel Type
P
R
A
Set Comfort Level
A to/ an al/ ff
F el pe
ser Settings
Set at
ser Settings
2. Highlight “FUEL TYPE” using the “UP/
DOWN” buttons to the right side of the
display. Press “SELECT”.
MENU
1. At the starting screen, press “MENU”.
2. Highlight “USER SETTINGS” using the
“UP/DOWN” buttons to the right side of
the display. Press “SELECT”.
F
L S
L
C
Set Comfort Level
A to/ an al/ ff
F el pe
Soft ood Pellet
S nflo er Seeds
heat
S
R S
S
ser Settings
ard ood Pellet
emp nits F/C
Flame eight Ad st
emp ifferential
2. Highlight “AUTO/MANUAL/OFF”.
Press “SELECT”.
3. Scroll down and highlight “HARD-
WOOD PELLET” or your fuel type.
4. Now press “SELECT” to choose new
fuel
2. Highlight “TEMP UNITS F/C” using the
“UP/DOWN” buttons to the right side of
the display. Press “SELECT”.
A
/
A
AL S
S
A tomati
an al
ff
C
F R
F
L C
A
Please empt hopper
of old f el t pe and
ens re fire
o
is lean
Please refer to
se tion in man al
DONE
3. Highlight “MANUAL”. Press “SELECT”.
4. Press “DONE” twice or wait 15 seconds
for starting screen to reappear.
5. Press “DONE” to confirm fuel
change.
3. Press the “UP” or “DOWN” button
to set desired temperature unit and
press “SELECT”..
6. Press “DONE” twice or wait 15 sec-
onds for starting screen to reap-
pear.
7. Fill the hopper with fuel, and if the
hopper was completely empty, or has
run out of fuel, throw approximately
1/2 cup of pellets into the firepot.
4. Press “DONE”. Press “DONE” again,
or wait 15 seconds for starting screen
to reappear.
8. Be sure the hopper lid and glass
door are both closed.
Page 26
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
H. Quick Start Guide (Cont’d)
SETTING COMFORT LEVEL
SETTING HEAT OUTPUT
P
1
30 PM
R
A
READ
Set at
Holdat 74
71
MENU
HEAT OUTPUT
MENU
HEAT OUTPUT
1. At the starting screen, press “HEAT
OUTPUT”.
1. Press and hold “UP” or “DOWN” but-
ton to set desired temperature.
NOTE: Set temperature must be 3
degrees higher than room
temperature for appliance to
start.
edi m igh
2. Use the “UP” button to change “HEAT
OUTPUT LEVEL” to ”MEDIUM-HIGH”.
F
3. Press “DONE” or wait 15 seconds for
starting screen to reappear.
2. Press “HOLD TEMP”.
S
C
F
R
L V L
F
L
R
S
3. Press “DONE”.
Page 27
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
I. Frequently Asked Questions
ISSUES
SOLUTIONS
1. Metallic noise
1. Noise is caused by metal expanding and contracting as
it heats up and cools down, similar to the sound pro-
duced by a furnace or heating duct. This noise does not
affect the operation or longevity of your appliance.
2. Ash build-up on glass
3. Glass has turned dirty
2. This is normal. Clean the glass.
3. Excessive build up of ash. The lower burn settings will
produce more ash, the higher burn settings produce
less. The more it burns on low the more frequent clean-
ing of the glass is required.
4. Fire has tall flames with black tails and is lazy
4. The flame height adjustment needs to be reduced or
the firepot needs cleaning. Heat exchanger or exhaust
blower needs cleaning.
5. Excessive smokey start-up
6. Large flame at start-up
5. Either the firepot is dirty or there is too much fuel at
start-up and not enough air.
6. This is normal. Flame will settle down once the fire is
established. Some smoke is normal.
7. Mechanical Noise
7. The floor of the firepot in the auto-clean system may
make some noise as it scrapes the ash into the ash
pan.
CAUTION
Odors and vapors released during initial operation.
•
•
Curing of high temperature paint.
Open windows for air circulation.
Odors may be irritating to sensitive individuals.
Page 28
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
With proper installation, operation, and maintenance your appliance will provide years of
trouble-free service. If you do experience a problem, this troubleshooting guide will assist
a qualified service person in the diagnosis of a problem and the corrective action to be
taken. This troubleshooting guide can only be used by a qualified service technician.
Troubleshooting
9
Possible Cause
Corrective Action
Error Message
Bad wall control or control board
3 wires have loose connections or installed
wrong
Replace wall control or control board
Check connections
LOW BATTERY
Battery supply on battery backup is drained
Recharge battery
BAD TC DROP TUBE
Drop tube thermocouple is broken or leads are Check connections
reversed
(TC = Thermocouple)
Replace thermocouple
BAD TC FIREPOT
Firepot thermocouple is broken or leads are
reversed
Check connections
(TC = Thermocouple)
Replace thermocouple
SNAP DISC TRIPPED
Overheat sensor (snap disc) has tripped
Vacuum switch is bad
Unplug the appliance and then manually
reset snap disc
Check connections. Bypass vacuum
with jumper wire, if runs, switch is bad.
Replace switch
VACUUM SW ERROR
(SW = Switch)
Check vacuum hose
Vacuum hose is plugged/disconnected
COMB BLOWER JAMMED Combustion blower is blocked/jammed
Remove blockage
Replace blower if necessary
Must uplug the appliance to clear the
error
AUGER JAMMED
MISSED IGNITION
Auger jammed, feed motor bad
Pull the feed system and inspect
Clear jam. Press Retry
Igniter bad or poor harness connection
Out of fuel or fuel is bridging in hopper
Check connections, if OK replace igniter
Break up bridging pellets
Refill hopper
Faulty firepot thermocouple connection has
shorted.
Replace the thermocouple and then
press Retry
MIN FIREPOT TEMP
Out of fuel
Refill hopper
Add handful of pellets to firepot
Press Retry
MAX DROP TUBE TEMP
CONV BLOWER JAMMED
Wrong fuel table setting
Confim setting matches burning fuel
Adjust flame height
Flame height set too high
Convection blower blocked/jammed
Remove blockage
Replace blower if necessary
Must uplug the appliance to clear the
error
CHECK ASHPAN
Auto-clean jammed
If ashpan is empty, check for a jam. Use
a screw driver and firmly push in the
firepot floor holes and flex spring and
push toward home to release jam.
Auto-clean switch is bad
Replace switch
Linkage has become disconnected
Reconnect linkage
Hopper lid open while you refill the hopper
Fill hopper between cycle
Adjust or replace switch
Switch is out of adjustment (auger will not
function)
SCREEN GOES BLANK
Static discharge or nearby lightening or
Electric fast transients at the input mains
Unplug the power to the appliance and
plug it back in
Page 29
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Maintaining & Servicing Your Appliance
10
A. Proper Shutdown Procedure
CAUTION
1. Set the wall control thermostat to “OFF” on AUTOMATIC/
MANUAL SETTING screen and let the appliance com-
pletely cool. Figure 30.1. The exhaust blower must be
off before you can unplug the appliance before servic-
ing.
Shock and Smoke Hazard
• Proper Shutdown Procedure must be followed.
• Smoke spillage into room can occur if appliance
is not cool before unplugging.
• Risk of shock if appliance not unplugged before
servicing appliance.
2. Smoke spillage into the room can occur if the appliance
is not cool before unplugging.
3. There is a risk of shock if the appliance is not unplugged
before servicing the appliance.
.
Automatic
Manual
Off
Figure 30.1
B. Quick Reference Maintenance Chart
Cleaning or Inspection
Frequency
Daily Weekly Every 2 Monthly Yearly
Weeks
Ash Pan - Burning Pellets
Every 5 bags of fuel
Every 1 bag of fuel
OR
OR
X
Ash Pan - Burning Alternate Fuels
Ash Removal from Firebox
X
More frequently depending on the OR
fuel type or ash build-up
X
Auto-Clean Inspection
Blower, Combustion (Exhaust)
Blower, Convection
More frequently depending on the OR
fuel type
X
X
X
More frequently depending on the OR
fuel type
More frequently depending on the OR
fuel type
Door Latch Inspection
Prior to heating season
OR
OR
OR
OR
OR
X
Firebox - Prepare for Non-Burn Season At end of heating season
X
Firepot - Burning Pellets
Firepot - Burning Alternate Fuels
Glass
Every 3 bags
Every 1 bag
X
X
X
When clear view of firepot
becomes obscured
Heat Exchanger & Drop Tube
Hopper
Every 1 ton of fuel
OR
X
Every 1 ton of fuel or when chang- OR
ing fuel types
X
Top Vent Adapter
Venting System
More frequently depending on the OR
fuel type or ash build-up
X
X
More frequently depending on the OR
fuel type
Page 30
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
C. General Maintenance and Cleaning
3. Cleaning Ash Pan
•
Frequency:
1. Types of Fuel
Wood Pellet Fuel: Weekly or every 5 bags of fuel
Alternate Fuel: Daily
Depending on the type of fuel you are burning will dictate how
often the firepot cleans itself. If the fuel you are burning has
a high dirt or ash content or you are burning other biomass
fuels, it may be necessary to do a more thorough cleaning
during the burn season.
•
By: Homeowner
Locate the ash pan underneath the firepot. Slide the
ash pan straight out. Empty into a non-combustible
container and re-install ash pan. When replacing ash
pan push it back until it catches on the 2 side latches.
See Disposal of Ashes below.
The auto-clean firepot system will routinely clean the
firepot, at shutdown when the wall control is satisfied or the
predetermined amount of burn time has elapsed.
4. Ash Removal from Firebox
A clinker is formed when dirt, ash or a non-burnable
substance is heated to 2000°F (1093°C) and becomes glass-
like. Clinkers filling the ash pan will have to be cleaned out
more often than ash. Excessive clinkers will eventually jam
the auto-clean system and generate an error. Figure 31.1.
•
Frequency: Weekly or more frequently depending on
fuel type or ash build-up.
By: Homeowner
•
There must not be any hot ashes in the firebox during
cleaning so allow the appliance to completely cool.
Frequent cleaning of the ash in the firebox with a vacuum
cleaner will help slow down the build-up of ash in the
exhaust blower and vent system.
WARNING
Disposal of Ashes
•
Ashes should be placed in metal container
with tight fitting lid.
Clinker
•
Ashes should be retained in closed container
until all cinders have thoroughly cooled.
Figure 31.1 - Large Clinker
2. Auto-Clean System Inspection
5. Disposal of Ashes
•
Frequency: Monthly or more frequently depending
•
•
Frequency: As needed
By: Homeowner
on fuel type
•
By: Homeowner
Ashes should be placed in a metal container with a
tight-fitting lid. The closed container of ashes should
be placed on a non-combustible floor or on the ground,
well away from all combustible materials, pending final
disposal.
a. The appliance must be in complete shutdown,
completely cool and the exhaust blower off.
b. Inspect the auto-clean springs for any degradation or
deformation. As the springs heat up and cool down
they can lose tension.
If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the
closed container until all cinders have been thoroughly
cooled.
If there is a gap showing above the firepot floor it means
the springs have lost their tension and can not keep
the floor in the proper position.
This will cause ignition problems and fuel falling into
the ash pan. Replace them if that occurs.
c. Inspect the holes in the firepot floor for any debris.
They must be kept clear. If you are burning corn, the
holes have a tendency to fill with particles which will
need to be removed.
Page 31
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
d. A Micro Cleaning Kit can be purchased at your local
hardware store as an accessory for a shop vacuum.
Figure 32.2. Assemble the crevice tool. Figure 32.3.
6. Cleaning Firepot with Firepot Clean-Out Tool
•
Frequency:
Softwood Pellets: Weekly or every 5 bags
Hardwood Pellets: Weekly or every 3 bags
Alternate Pellets: Daily or every 1 bag
By: Homeowner
•
a. The appliance must be in complete shutdown,
completely cool and the exhaust blower off.
b. It may be necessary to use your firepot clean-out tool
to chip away material that has built up on the sides of
the firepot and to push out any clinkers. Larger clinkers
may have to be removed from the top of the firepot.
Corn clinkers can be especially difficult to break up. If
the clinker adheres to the sides of the firepot, you will
need to manually clean the firepot.
Figure 32.2
c. After cleaning the firepot and inspecting the holes,
turn off the power and then restore the power. The
auto- clean system will then clean itself.
d. The firepot floor plate must be fully closed when
finished.
Figure 32.3
se the crevice tool to finish cleaning the heat
exchanger fins. It is critical that the 2 exhaust exits
at the back of the firebox floor (left and right) be
thoroughly cleaned. Figure 33.4. There are several
ways this can done.
e.
U
7. Cleaning Heat Exchanger & Drop Tube
•
•
Frequency: Monthly or every 1 ton of fuel
By: Homeowner
a. The appliance must be in complete shutdown,
completely cool and the exhaust blower off.
1. Use the crevice tool.
2. Attach a hose 1/2 inch (12.7mm) in diameter and
approximately 2 feet (607mm) in length to your
vacuum hose.
3. Use a bottle brush and push the ash down to the
bottom. Remove the exhaust blower and then
vacuum out the ash. Figures 33.1-4 on page 33.
b. It is necessary to remove the baffle to gain access
to the heat exchanger. Follow instructions for baffle
removal on page 35.
c. Vacuum the ash from the heat exchanger with an
upholstery brush to remove the majority of the ash.
Be sure to vacuum the back of the baffle also. Inspect
the drop tube and remove any residue build-up in the
drop tube. Figure 323.1.
exhaust exits left and right side must
e thoroughly cleaned. Each exit is
approximately 4 inches wide, 1 inch
across and 3 inches deep.
Figure 32.1
Figure 32.4
Page 32
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
f. Removing the Combustion (Exhaust) Blower
Set lo er on top of ho sing
o not dis onne t the ires
1. The combustion blower is mounted in the bottom
right rear of the appliance. Figure 33.1.
2. Use an 11/32 nut driver to loosen all six nuts, but do
not remove. Rotate the blower and remove from the
housing. Figure 33.2.
3. Set the blower on the top of the housing. You do not
need to disconnect the wires. Figure 33.3.
4. Vacuum out the exhaust area. Figure 33.4.
Figure 33.3
Va
m o t the e ha st area
Figure 33.4
Combustion Blower
Figure 33.1
Loosen all n ts
t do
Remove
Figure 33.2
Page 33
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
8. Cleaning the Hopper
11. Cleaning Convection Blower - Requires No
Lubrication
•
Frequency: Monthly, every 1 ton of fuel or when
changing fuel types.
By: Homeowner
•
•
•
Frequency: Yearly or as needed
By: Qualified Service Technician
Task: Contact your local dealer.
•
After burning approximately 1 ton of fuel you will need
to clean the hopper to prevent sawdust and/or fines
build-up. A combination of sawdust/fines and pellets
on the auger reduces the amount of fuel supply to the
firepot. This can result in nuisance shut downs and
mis-starts.
12. Door Latch Inspection
•
•
•
Frequency: Prior to heating season
By: Homeowner
Task:
a. The appliance must be in complete shutdown and
cool and the exhaust blower off
The door latch is non-adjustable but the gasketing between
the glass and firebox should be inspected periodically to
make sure there is a good seal. If the gasket is frayed or
damaged, replace with a new one.
b. Empty the hopper of any remaining pellets.
c. Vacuum the hopper and feed tube.
13. Soot and Fly Ash: Formation & Need for Removal
in Exhaust Venting System.
9. Cleaning the Glass
•
Frequency: Yearly or more frequently depending on
fuel type or ash build-up
•
•
Frequency: When clear view of the firepot is obscured
By: Homeowner
•
By: Qualified Service Technician/Homeowner
a. Appliance must be completely cool before cleaning
glass.
The products of combustion will contain small particles
of fly ash. The fly ash will collect in the exhaust venting
system and restrict the flow of the flue gases.
b. Use a damp paper towel or any non-abrasive glass
cleaner. Wipe off with dry towel.
At start-up if there is incomplete combustion, or if there
is a shutdown or incorrect operation of the appliance it
will lead to some soot formation. This will collect in the
exhaust venting system.
WARNING
Handle glass doors with care.
The venting system may need to be cleaned at least
once a year or more often depending upon the quality
of your fuel or if there is a lot of horizontal pipe sec-
tions. Ash will build up more quickly in the horizontal
sections.
•
•
•
Inspect the gasket to ensure it is undamaged.
Do NOT strike, slam or scratch glass.
Do NOT operate appliance with glass door
removed, cracked, broken or scratched.
14. Cleaning the Top Vent Adapter (if installed)
•
Frequency: Yearly or more frequently depending on
fuel type or ash build-up
By: Homeowner
CAUTION
•
Handle glass assembly with care.
a. The appliance must be in complete shutdown,
completely cool and the exhaust blower off.
When cleaning glass door:
b. Open the clean-out cover. Figure 34.1.
•
Avoid striking, scratching or slamming
glass.
c. Sweep out any ash build-up.
NOTE: There are heavy duty vacuum cleaners specifically
designed for solid fuel appliance cleaning.
•
•
•
Do NOT clean glass when hot.
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white film.
Refer to maintenance instructions.
10. Cleaning Exhaust Blower - Requires No
Lubrication
•
•
•
Frequency: Yearly or as needed
By: Qualified Service Technician
Task: Contact your local dealer.
Clean-Out Cover
Figure 34.1
Page 34
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
E. Baffle Removal
15. Preparing Firebox for Non-Burn Season
•
•
Frequency: At the end of heating season
By: Homeowner
WARNING
Cast iron is a very heavy material. The baffle is
made of cast iron and therefore is heavy and awk-
ward at times to maneuver. Clear and prepare
your work area before you begin.
a. The appliance must be in complete shutdown and
allow the appliance to completely cool down.
b. Remove all ash from the firebox and vacuum thor-
oughly.
c. Paint all exposed steel, including cast-iron. Use
the Touch-Up paint supplied with the appliance or
purchase paint from your local dealer. You must
use a high-temperature paint made specificially for
heating appliances.
a. The appliance must be in complete shutdown, com-
pletely cool and the exhaust blower off.
b. Open door.
c. The baffle is located at the top inside of firebox.
D. High Ash Fuel Content Maintenance
d. Remove baffle by placing a flat head screw driver into
the slot of the latches located in the upper corners and
push down. The bottom of the latch will fall forward off
of the post. Lift the baffle up and then out toward you.
Figure 35.2.
•
Frequency: When the ash exceeds more than half
way up the firepot.
By: Homeowner
•
If the ash build-up exceeds the half way point in the firepot
before it automatically cleans, then the firepot is not being
cleaned often enough.
e. To replace the baffle, place the 2 locating ears behind
the bottom edge and tilt the baffle up and into place.
f. The baffle must be centered in the firebox before latch-
ing it in place. If it is not centered the latch is trapped
between the baffle and side of the firebox instead of
latching properly.
Another symptom is if clinkers are adhering to the sides
of the firepot. Double check the wall control to ensure the
proper setting has been selected for the fuel you are burning.
If that is correct, change the setting to “Utility Pellet”.
g. The bottom of the latches will fit over the posts. Push
the top of the latch forward to lock latch into place.
WARNING
Fire and Smoke Risk.
• High ash fuels or lack of maintenance
can cause firepot to overfill. Follow
proper shutdown procedure if ash buildup
exceeds half way point in firepot.
Baffle
• Failure to do so could result in smoking,
sooting and possible hopper fires.
Pellets a k
in Feed
p
e
Latches
Locating ears - 1 on
each side. Fit behind
bottom edge.
Insert flat head screw driver into “V”
section and push down and the bottom
of the latch will fall forward off of post
Firepot verfills
Figure 35.2
Ash
ild p in Fire o
Figure 35.1
Page 35
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
F. Convection Blower Replacement
1. Follow the proper shut down procedures as outlined on
page 30, Section 10.A.
2. Remove the left and right side panels by removing the 4
screws using a Phillips head screw driver. Figure 36.1.
3. Depress the tab on the left side and snap out the power
supply. You do not need to disconnect any wires.
Figure 36.1.
ot h
Lat h
4. Remove the 2 screws at the bottom of the back panel so
there will be room to remove the blower. Figure 36.1
5. Reach behind the blower and release the latch by push-
ing the top of the latch towards the blower. Figure 36.2.
Figure 36.2
6. Rock the top of the blower slightly and lift up. The
blower will pass around the control board and out the
left side of the appliance.
7. Disconnect the wire harness from the bottom of the
blower by depressing the tabs on the sides of the con-
nector and then pulling to remove. Figure 36.1.
8. Re-connect wire harness to the new blower.
9. Install replacement blower by placing the bottom flange
into the opening first then rotate blower up into posi-
tion.
Lat h ngaged
10. When the blower is properly positioned the latch will engage
the notch to hold the blower in place. Figure 36.3.
11. Re-secure the back panel, snap the power supply back
in and re-secure the side panel(s).
Figure 36.3
Remove
Right Side
Panel
epress a and
Snap t Po er
S ppl
Remove
Left Side
Panel
Remove
Screws
Disconnect Wire Harness
from Bottom of Blower
Figure 36.1
Page 36
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
H. Glass Replacement
G. Combustion (Exhaust) Blower
Replacement
1. Follow the proper shut down procedures as outlined on
WARNING
Glass is 5mm thick high temperature heat-re-
sistant ceramic glass.
page 30, Section 10.A.
•
2. Remove the right side panel by removing the 4 screws
using a Phillips head screw driver. Figure 37.1.
•
•
DO NOT REPLACE with any other material.
3. It is not necessary or recommended to remove the
housing to replace or service the combustion blower.
You only need to remove the motor and impeller.
Alternate material may shatter and cause
injury.
4. Disconnect the wire from the control board connection
points #1 and #8. Depress the tab on the connector to
disconnect the wire (similar to a telephone connector).
See Figure 39.1 on page 39 for the locations of #1
and #8.
a. Swing open the face and remove the door from the
appliance by lifting the door off of the hinge pins and
lay on a flat surface face down.
b. Using a Phillips head screw driver, remove 4 screws,
2 on the top and 2 on the bottom. Remove metal
bracket and then remove the glass. Figure 37.2.
5. Using an 11/32 socket or nut driver, remove the (6)
8x32 nuts securing the motor and impeller to the hous-
ing.
c. Replace with new glass with gasket.
6. Holding the black plastic body of the motor, rotate the
impeller counter-clockwise until blades line up with
opening in the housing and remove motor and impel-
ler.
d. Re-attach metal bracket with 4 screws.
e. Re-install door over hinge pins and close face.
7. If the gasket between housing and motor is damaged it
will have to be replaced. A gasket is included with the
replacement blower.
8. Re-install in reverse order.
Remove 4 screws
Metal Bracket
Glass with Gasket
Figure 37.2
Remove
Side
Panel
Remove (6) Nuts
Figure 37.1
Page 37
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Reference Materials
11
When describing the location of a component,
it is always AS YOU FACE THE FRONT OF
THE APPLIANCE.
A. Component Functions
1. Auto-Clean Motor
ꢀ
The auto-clean motor is located under and behind the
firepot on the left side, inside the convection air chamber.
It automatically opens and closes the firepot floor so ashes
can fall into the ash pan.
9. Firepot
The firepot is made of high quality ductile iron. The floor of
the firepot automatically opens for cleaning and is operated
by the auto-clean firepot system. The floor needs to return
to a completely closed position or the appliance will not
operate properly.
2. Auto-Clean Switch
The auto-clean switch is located on top of the auto-clean
motor. It communicates to the control board when the firepot
floor is open and when the auto-clean system has completed
its cycle and is back in the home (closed) position.
10. Fuses
There are three fuses. Two fuses are located on the inside
of the control board. One fuse is AC and operates the
igniter and the other fuse is DC and operates all of the
other components. The third fuse is located in the power
supply. A fuse will blow should a short occur and shut off
power to the appliance. The fuses can only be replaced by
an authorized dealer.
3. 12 Volt Battery Back-Up Cable
This is an optional accessory. It will plug into the appliance
at the rear of the appliance. An icon will display on the
wall control when the appliance has lost main power and is
running on battery back-up.
4. Combustion (Exhaust) Blower
11. Heat Exchanger
The combustion (exhaust) blower is mounted in the bottom
right rear of appliance. The blower is designed to pull the
exhaust from the appliance and push it out through the
venting system.
The heat exchanger is located behind the baffle and it
transfers heat from the exhaust system into the convection
air chamber. Remove the cast iron baffle to access the heat
exchanger.
5. Control Board
12. Hopper Lid Switch
The control board is located on the lower left side of appliance.
It controls the functioning of the appliance and communicates
with the wall control. The control board can only be opened
by an authorized dealer.
The hopper lid switch is located on the right side inside the
hopper. It senses whether the hopper lid is open and displays
an icon on the wall control and will turn off the feed motor.
13. Igniter (Heating Element)
6. Convection Blower
The igniter is mounted on the base of the firepot. Combustion
air travels over the red hot igniter creating super heated air
that ignites the pellets or other fuels.
The convection blower is mounted at the bottom left rear of
the appliance. The convection blower pushes heated air
through the heat exchange system into the room.
14. Low Fuel Indicator
7. Door Switch
The low fuel indicator is attached to the left side of the hopper.
It senses the amount of fuel in the hopper and will display
an icon on the wall control.
The door switch is mounted on the right side of the firebox
behind the door handle. It senses when the door is open
and will display an icon on the wall control, and will turn off
the auto-clean system and feed motor for safety.
15. Optical Switch for the Auger
The optical switch is located on top of the feed system and
communicates to the wall control that the auger is spinning
or if it has stopped.
8. Feed System
The feed system is located on the right side of the appliance
and can be removed as an entire assembly. The assembly
includes the feed motor, mounting bracket, bearing and feed
spring (auger). The hollow feed spring (auger) pulls pellets
up the feed tube from the hopper area and drops them down
the feed chute into the firepot.
16. Power Receptacle
The power receptacle is located on the lower rear of the
appliance. Check the wall receptacle for 120 volt, 60 Hz
(standard current). Make sure the outlet is grounded and
has the correct polarity. A good quality surge protector is
hightly recommended to protect the electronics.
Page 38
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
17. Power Supply
21. Vacuum Switch
The power supply is located at the rear of the appliance. It
converts 120 volt AC current to 15 volt DC current to power
the appliance.
The vacuum switch is located on the right side of the
appliance under the feed motor behind right side panel and
connects to the drop tube with a hose. This switch turns
the feed system on when vacuum is present in the firebox.
The vacuum switch is a safety device to shut off the feed
motor if the exhaust or the heat exchanger system is dirty,
plugged or if the firebox door is open.
18. Overheat Sensor (Snap Disc)
The overheat sensor is mounted on the back of the drop tube in
the center of the appliance and has a reset button. To access
it remove the right side panel. If the fire tries to burn back
into the feed system or push exhaust up the feed tube, this
sensor will shut the stove down, however the wall control will
still display messages. This sensor must be manually re-set.
Disconnect power before resetting.
22. Wall Control
The appliance is designed to run on a custom designed 3.3
volt DC thermostat wall control. It will not operate on any
other wall control. Refer to the instructions supplied with
the thermostat wall control.
19. Thermocouple - Firepot
This thermocouple is located on top of the firepot inside
the thermocouple cover (ceramic protection tube). The
thermocouple sends a millivolt signal to the control board
telling the control board there is a fire in the firepot.
23. Wiring Schematic for Control Board
See Figure 39.1 below.
24. Wiring Schematic for Power Supply
See Figure 39.2 below.
20. Thermocouple - Drop Tube
This thermocouple is located on the bottom of the drop
tube on the right side and attached with a wing nut. It turns
the convection blower on and off, varies the speed of the
convection blower and will shut down appliance if internal
heat exceeds set temperature.
Fuse 15A 250V
(need to remove
cover)
n/a
6
13 12
11
10
9
5
8
7
4
3
2
Fuse 15A 120V,
under the cover
14
1
120V AC out to
Control Board
15V DC out to
Control Board
120V AC in
Figure 39.2
Fuse 15A 120V,
under the cover
15
16
17
Figure 39.1
#
Description
#
Description
#
Description
1
2
3
4
5
Combustion Blower
Auto-Clean System
Feed/Auger Motors
7
8
9
Thermostat Wall Control
12 Igniter
Combustion Blower (feedback)
Firepot Thermocouple
13 AC Power In for Igniter
14 Convection Blower Power
15 Overheat Sensor (Snap Disc)
16 DC Power In from Power Supply
17 12 Volt Battery Back-up
Hopper/Door Switches
10 Drop Tube Thermocouple
n/a Not Used
Auger/Auto-Clean/Vacuum
Switches
11 Convection Blower (feedback)
6
Low Fuel
Page 39
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
B. Component Locations
LEFT SIDE
Heat Exchanger,
Front & Back
Low Fuel
Indicator
Drob Tube
Power
Supply
Baffle
Convection
Blower
Ash Pan
Firepot
Control Board
Feed Motor
Thermocouple and
Thermocouple Cover
Figure 40.1
Figure 40.2
RIGHT SIDE
Vacuum
Switch
Overheat
Sensor
Wing Nut - Securing
Overheat Sensor in
place
Combustion
Blower
Figure 40.3
Page 40
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
C. Exploded Drawings
Item
Description
Magnet & Bracket Assembly
Latch, Door Assembly
Glass Assembly
Glass Retainer
Hinge, Female
Part Number
7034-008
7034-039
7034-007
7034-136
450-2910
7034-026
7034-185
1
2
3
4
5
6
7
5
Door Frame Assembly
Door Air Deflector
4
6
3
7
2
1
Glass Size: 21 in. w x 14 in. h.
Figure 41.1 - Door, Glass & Door Latch Assembly
Item
Description
10 Auto-Clean Link Arm
11 Auto-Clean Plow
Part Number
7034-176
7034-024
SRV7034-152
7000-299/4
7000-374/10
7034-153
17
Auto-Clean Motor Arm Assembled
18
19
22
20
12 Auto-Clean Rail
16
13 Spring, Auto-Clean, Qty: 4
14 Clip, Hitch Pin 3/32, Qty: 10
15 Firepot Bottom
16 Heating Element (Igniter) 18” SRV7000-226
21
23
17 Thermocouple
18 Clip, Half
SRV7000-334
7000-321
25
24
19 Thermocouple Cover
20 Firepot Assembly
21 Gasket, Firepot
22 Auto-Clean Motor/ Arm Assy
23 Auto-Clean Lever
24 Gasket, Auto-Clean
25 Auto-Clean Motor Mount
26 Bearing
SRV7034-186
SRV7034-010
7034-190
7034-020
7034-158
26
27
28
29
30
31
15
7034-165
not sold sep.
14
13
32
7000-333
not sold sep.
27 Crank Arm
12
10
not sold sep.
28 Spacer
11
29 Auto-Clean Cam Switch
SRV7034-187
30 Switch, Micro, Normally Open 7000-327
Figure 41.2 - Firepot, Igniter & Auto-Clean System
31 Motor 12 Volt
7000-300
7034-188
32 Auto-Clean Motor Grommet
Page 41
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Figure 42.1
Item
35 Ash Lip
36 Door, Cast, Right
37 Door Assembly
38 Ash Pan Assembly
39 Gasket, Ash Door
40 Gasket, (Rope) Door
41 Switch, Magnetic
42 Bracket, Latch
Description
Item
49
50
51
52
53
54
55
56
Description
Exhaust Transition
Gasket, Blower, Convection
Detent Pin 3/16
Blower, Convection
Power Supply
Item
63
64
65
66
67
68
69
70
71
72
73
Description
Shroud, Left
Top, Cast
Side Mount, Left
Hinge, Male, Door
Latch, Baffle
Baffle
Feed Motor
Switch, Optical Assembly
Bracket, Feed Motor
Sensor, Overheat (Snap Disc)
Gasket, Feed Motor
Feed Spring Assembly
Shroud, Rear
Front, Cast
Door, Cast, Left
Clip Receiver
Ash Pan Door
Intake Shield
43 Vacuum Switch
57
58
59
60
61
62
44 Side Mount, Right
45 Side, Cast. Left & Right
46 Shroud, Right
47 Blower, Combustion (Exhaust)
48 Control Board
Hopper Top
Hopper Lid
Page 42
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
D. Service Parts and Accessories
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on the Quadra-
correct service parts.
Item No.
Accessories
Part No.
12VCORD-AE
SCR-7005
LOGS-60-AE
OAK-3
12 Volt Power Cord
Firescreen
Log Set, 2 pieces
Outside Air Kit
Rear Vent to Top Vent, Short, 90 degrees with Clean-Out
Rear Vent Adapter with Clean-Out
811-0610
811-0620
Top Vent Adapter, 3 to 3 inch Offset
811-0720
Top Vent Adapter, 3 to 6 inch Offset
812-3570
Top Vent Adapter
TPVNT-3
Warming Shelves with Brackets, Matte Black (pair)
Warming Shelves with Bracket, Porcelain Mahogany (pair)
Warming Shelves with Bracket, Powder Coat, Sienna Bronze (pair)
Warming Shelves with Bracket, Powder Coat, Willow (pair)
844-9780
844-9810
WSLG-CSB
WSLG-CWL
Item No.
Service Parts
Part No.
35
35
35
35
38
72
Ash Lip, Matte Black
7005-111MBK
7005-111PMH
7005-111CSB
7005-111CWL
7034-013
Ash Lip, Porcelain, Mahogany
Ash Lip, Powder Coat, Sienna Bronze
Ash Lip, Powder Coat, Willow
Ash Pan Assembly
Ash Pan Door
7034-133
Auto-Clean Bottom Assembly
Auto-Clean Lever
Auto-Clean Link Arm
Auto-Clean Motor Arm Assembly
Auto-Clean Motor Grommet
Auto-Clean Plow
Auto-Clean Rail
Auto-Clean Switch Cam
Baffle
Bearing for Auto-Clean System, Qty: 1
Blower, Combustion (Exhaust) with Gasket
Blower, Convection
7034-021
7034-158
7034-176
7034-020
7034-188
7034-024
SRV7034-152
SRV7034-187
SRV7034-148
7000-333
23
10
22
32
11
12
29
68
26
47
52
7034-033
SRV7000-260
7036-145
Bracket, Catch
Bracket, Control Board
Bracket, Door Switch
7034-212
7034-215
56
Bracket, Feed Motor
7034-143
Bracket, Hopper Switch
7034-216
Page 43
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Item No.
Service Parts
Part No.
7034-014
42
Bracket, Latch Assembly
Bracket, Overheat Sensor (Snap Disc)
Bracket, Vacuum Switch
Clip, Half, for Auto Clean System
Clip, Hitch Pin 3/32, Qty: 10
Clip, Receiver, Black
7034-150
7034-211
7000-321
7000-374/10
704-832
18
14
71
Clip, Wire, Qty: 10
7000-400/10
7034-037
Component Pack, Mahogany (includes owner’s manual, warranty card, quick start
guide, heat exchanger 7 exhaust cleaning instructions, DVD “How To”, wall control &
harness, power cord, (4) leveling nuts & bolts, firepot clean-out tool, touch-up paint
and label “If Fireplace Altered”)
Component Pack, Matte Black, (see above for contents)
Component Pack, Sienna Bronze, (see above for contents)
Component Pack, Willow, includes, (see above for contents)
Control Board
Detent Pin for Convection Blower
Door Assembly
7034-034
7034-035
7034-036
SRV7000-456
7000-376
48
51
37
6
7034-006
7034-026
Door Frame Assembly
7
Door, Air Deflector
7034-185
2
Door Latch Assembly
7034-039
70
70
70
70
36
36
36
36
Door, Left, Matte Black
7005-110MBK
7005-110PMH
7005-110CSB
7005-110CWL
7005-109MBK
7005-109PMH
7005-109CSB
7005-109CWL
7000-393
Door, Left, Porcelain Mahogany
Door, Left, Powder Coat, Sienna Bronze
Door, Left, Powder Coat, Willow
Door, Right, Matte Black
Door, Right, Porcelain, Mahogany
Door, Right, Powder Coat, Sienna Bronze
Door, Right, Powder Coat, Willow
Elbow, Catch
49
54
Exhaust Transition Assembly
Face Plate, located behind Ash Removal Door
Feed Motor, DC Current
Feed Motor & Spring Assembly
Feed Spring Only
7034-139
7034-124
SRV7000-313
7034-004
SRV7001-046
SRV7034-010
7034-153
59
20
15
Firepot Assembly
Firepot Bottom
Firepot Clean-Out Tool
414-1140
Firepot Riser Clamp Assembly
Firepot Riser Assembly
Front, Matte Black
Front, Porcelain, Mahogany
Front, Powder Coat, Sienna Bronze
Front, Powder Coat, Willow
Gasket, (Rope), Ash Door
7034-012
SRV7034-002
7005-108MBK
7005-108PMH
7005-108CSB
7005-108CWL
SRV7034-178
SRV7034-177
69
69
69
69
39
40
Gasket, (Rope), Door
Page 44
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Item No.
Service Parts
Part No.
7034-165
7000-329
24
50
Gasket, Auto-Clean
Gasket, Blower, Convection
Gasket, Blower, Combustion, goes between blower housing and stove
Gasket, Blower, Combustion, goes between blower housing and motor
Gasket, Exhaust
SRV7000-332
SRV7000-423
7034-109
Gasket, Extruded Edge, 10 ft, Hopper
Gasket, Extruded, 10 ft, Hopper Lid
Gasket, Feed Motor
7000-319/10
7000-320/10
7034-144
58
21
Gasket, Firepot
7034-190
Gasket, Glass, 1/8” x 1-1/4”, 10 ft.
Glass Assembly, Door
Glass Retainer
7000-377/10
7034-007
7034-136
3
4
16
Heating Element, 18” (Igniter)
Heating Element, 18” (Igniter), Qty: 10
Hinge Arm, Left, Hopper Lid
Hinge Arm, Right, Hopper Lid
Hinge, Female, Door
SRV7000-226
7000-226/10
7034-161
7034-160
450-2910
5
66
Hinge, Male, Door
7034-138
Hinge Pin, Hopper Lid, Qty: 1
Hinge Retainer, Hopper Lid
Hopper Lid, Matte Black
Hopper Lid, Porcelain, Mahogany
Hopper Lid, Powder Coat, Sienna Bronze
Hopper Lid, Powder Coat, Willow
Hopper Top
7034-159
7034-163
62
62
62
62
61
73
67
7034-157MBK
7034-157PMH
7034-157CSB
7034-157CWL
7034-169
Intake Shield
Latch, Baffle
7034-224
7034-149
Log, Front, Left
7034-227
Log, Front, Right
7034-226
Magnet, Round
Magnet & Bracket Assembly
Motor, Gear, Auto-Clean
SRV7000-140
7034-008
7000-300
1
31
Paint, Touch-Up, Matte Black
Paint, Touch-Up, Porcelain Mahogany
Paint, Touch-Up, Powder Coat, Sienna Bronze
Paint, Touch-Up, Powder Coat, Willow
Paint, (1) 12 oz can, Powder Coat, Willow
Paint, (1) 12 oz can, Powder Coat, Sienna Bronze
Power Cord
7000-304
855-1450
TOUCHUP-CSB
TOUCHUP-CWL
PAINT1-CWL/CTO
PAINT1-CSB/CES
812-1180
53
Power Supply Assembly
SRV7000-324
Rivet, Button head, Gold
Qty 1: 72171
Qty 2: 844-5750
Rivnut Repair Kit, 1/4-20
Screw 1/4-20 x 3/8”, Qty: 24
Screw 1/4-20 x 5/8”, Qty: 24
RIVNUT-REPAIR
7000-401/24
7000-398/24
Page 45
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Item No.
Service Parts
Part No.
57
Sensor, Overheat (Snap Disc)
Sensor, Fuel Level
230-1290
7000-380
60
63
46
65
44
45
45
45
45
13
41
30
55
17
19
Shroud, Rear
Shroud, Left
Shroud, Right
Side Mount, Left
Side Mount, Right
Side, Matte Black
Side, Porcelain, Mahogany
Side, Powder Coat, Sienna Bronze
Side, Powder Coat, Willow
Spring, for Auto-Clean, Qty: 4
Switch, Magnetic
Switch, Micro, Normally Open
Switch, Optical Assembly
Thermocouple, Firepot
Thermocouple Cover
Thermocouple Ring Mount
Thermostat Wire, 3 Conductor
Top, Matte Black
7034-170
7034-172
7034-171
7034-128
7034-126
7005-107MBK
7005-107PMH
7005-107CSB
7005-107CWL
7000-299/4
7000-375
7000-327
7034-038
SRV7000-334
SRV7034-186
SRV7000-381
7000-409
7034-155MBK
7034-155PMH
7034-155CSB
7034-155CWL
7000-373
64
64
64
64
Top, Porcelain, Mahogany
Top, Powder Coat, Sienna Bronze
Top, Powder Coat, Willow
Vacuum Hose
43
Vacuum Switch
SRV7000-166
SRV7000-451
SRV7034-191
7034-202
Wall Control, Thermostat, Programmable
Wire Harness, Auger, Auto Clean, Vacuum Switch
Wire Harness, Battery Back-up
Wire Harness, Convection Blower
Wire Harness, Door, Hopper
Wire Harness, Igniter (Heating Element)
Wire Harness, Overheat Sensor
7034-219
SRV7034-192
SRV7034-199
7034-193
Wire Harness, Power Out, AC Current
Wire Harness, Power Out, DC Current
Wire Harness, Power (Supply) Receptacle
Wire Harness, Thermostat
7034-220
7034-221
SRV7034-233
SRV7034-200
Appliances
Mt. Vernon AE, Matte Black
Mt. Vernon, AE Porcelain, Mahogany
Mt. Vernon, AE, Powder Coat, Sienna Bronze
Mt. Vernon, AE, Powder Coat, Willow
Part No.
MTVERNON-AE-MBK
MTVERNON-AE-PMH
MTVERNON-AE-CSB
MTVERNON-AE-CWL
Page 46
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
E. Service And Maintenance Log
Date of Service
Performed By
Description of Service
Page 47
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
E. Service And Maintenance Log (Cont’d)
Date of Service
Performed By
Description of Service
Page 48
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
F. Homeowner’s Notes
Page 49
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
G. Warranty Policy
Hearth & Home Technologies LIMITED WARRANTY
Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood,
pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or
Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
HHT Manufactured Appliances and Venting
EPA
Warranty Period
Parts Labor
Components Covered
Gas
X
Wood
X
Pellet
X
Electric
X
Venting
X
Wood
All Parts and Material Except
as covered by Conditions,
Exclusion, and Limitations
listed
1 Year
X
Igniters, Electronic Compo-
nents, and Glass
Blowers
X
X
X
X
2 years
3 years
X
X
X
Molded Refractory Panels
X
X
Firepots
5 years
3 years
3 years
X
X
Castings & Baffles
Firebox, HHT Chimney, Termi-
nation & Heat Exchanger
7 years
X
X
X
X
10
1 year
1 year
X
years
Burners, Logs & Refractory
Limited
Lifetime
X
X
Firebox & Heat Exchanger
All Replacement Parts
90 Days
X
X
X
See Conditions, Exclusions, and limitations.
CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY
9-01-08
ꢀ
This warranty applies to the original owner and is transferable up to two years from date of purchase to the new
homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance
remains in its original place of installation.
ꢀ
ꢀ
ꢀ
The maximum amount recoverable under this warranty is limited to the purchase price of the product.
In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.
Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the
home is not covered under this warranty.
ꢀ
This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing,
glass gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or
corrosion on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered
by this warranty.
ꢀ
Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to
this noise are not covered by this warranty.
4021-645A 09-01-08
Page 50
7034-106E
September 1, 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
R
Mt. Vernon Pellet Stove (AE)
Hearth & Home Technologies LIMITED WARRANTY (Cont’d)
ꢀ
HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or main-
tenance of the appliance not in accordance with the installation instructions; operating instructions and the listing
agent identification label furnished with the appliance; (2) installation which does not comply with local building codes;
(3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environ-
mental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure or handling
devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than those specified
in the operating instructions; (6) installation or use of components not supplied with the appliance or any other compo-
nents not expressly authorized and approved by HHT; and/or (7) modification of the appliance not expressly autho-
rized and approved by HHT in writing.
ꢀ
ꢀ
This warranty does not apply to non-HHT venting components, hearth components or other accessories used in con-
junction with the installation of this product.
This warranty is void if the appliance has been over-fired or operated in atmospheres contaminated by chlorine,
fluorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or
there is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
ꢀ
HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship
during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the
defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.
ꢀ
ꢀ
Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not
apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF
THE WARRANTY SPECIFIED ABOVE.
This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all war-
ranties currently in existence.
If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide neces-
sary parts or components, contact the nearest authorized HHT dealer or supplier.
4021-645A 09-01-08
Page 51
September 1, 2008
7034-106E
Download from Www.Somanuals.com. All Manuals Search And Download.
R
O T
T
O
T O :
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
visit our web site at www.quadrafire.com
NOTICE
DO NOT DISCARD THIS MANUAL
•
Read, understand and
follow these instruc-
tions for safe installa-
tion and operation.
•
Leave this manual with
party responsible for use
and operation.
• Important operating and
maintenance instruc-
tions included.
We recommend that you record the following pertinent
information for your MT. VERNON PELLET STOVE (AE)
Date purchased/installed:
Serial Number:
Location on appliance:
Dealer phone:
Dealership purchased from:
Notes:
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534,
5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407,
5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099,
6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579,
6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441,
6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264,
2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
7034-106E
September 1, 2008
Page 52
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Quadra Fire Indoor Fireplace CB1200I User Guide
Razor Motorcycle 15130760 User Guide
RCA Telephone 2 9398 User Guide
Rosewill Work Light RSL 113 User Guide
Samsung Cell Phone 4G LTE SMARTPHONE User Guide
Samsung Digital Photo Frame 700T User Guide
Samsung Microwave Oven CM1020B User Guide
Samsung Oven BT620FQST User Guide
Seagate Computer Drive 100686584 User Guide
Sekonic Camera Accessories 57 User Guide