PLD35MU
Instruction Manual
ANG
USB
DVD/VCD/CD/MP3/USB/MMC
1
2
INT
3
RPT
BND
_
UP
DN
CLK
EQ
3.8 " TFT
SEL
+
APS
AUX
MU
RDM
5
-10
6
+10
4
MODE
REL
PWR
P/N
BAND
EQ
MU
MODE
MENU
SEL
0K
SETUP
+
Fully Compatible to These
1
2
4
8
3
7
-10
+10
5
6
Formats of Files: DVD,VCD,
JPEG,MP4,MP3,WMA,CD.
CLK
SLOW_FWD
LOC
9
0/10
10+
APS
ST
SEARCH
ZOOM
A-B
INT
RPT
RDM
AUDIO
TITLE/PBC
SUBTITLE
PROG
OSD
LOUD
STEP
DISC/USB/CARD/RADIO
4 IN 1 CAR AUDIO SYSTEM
Remark: Any information subject to change without further notice
Contents
1. Before Operation...........................................................................................3
1.1 Glossary................................................................................................ 3
1.2 Precautions............................................................................................3
1.3 Maintenance and Cleaning of Discs..........................................................4
1.4 Battery Information of the Remote Control.................................................4
1.5 The Remote Control Description...............................................................5
1.6 Description of the Face of the Front Panel.................................................6
1.7 Description of the Unit Chassis Facet After removing the Front Panel..........6
1.8 Description of the Unit Chassis Facet After Sliding Down the Front Panel.....6
1.9 Description of the Rear Cabinet....................... ........................................7
1.10 Description of the Wires Harmness..........................................................7
1.11 Unit Installation......................................................................................8
7. Specification
General Specification
Power Supply Requirement..................................................DC 12V
Maximum Power Output...................4 x 80W(measured at DC 14.4 V)
Dimensions(w x h x d)...........................................178 x 50 x 167mm
DVD Deck Specification
2. Common Operation........................................................................................9
3. Radio Operation..........................................................................................10
Format....................................DVD/VCD/JPEG/MP4/MP3/WMA/CD
Video System..................................PAL/PAL-M/PAL-N/NTSC/AUTO
Audio System..............................................................24 bit/96KHz
Loading System.......................................................... Auto Loading
Mounting Angle.................................................................0 to +/-30
4. Basic Disc, USB or MMC/SD Operation..........................................................11
4.1 Begin Playback......................................................................................11
4.2 Pause Playback.....................................................................................12
4.3 Stop Playback .......................................................................................12
4.4 Select Chapter/Track with the UP/DN or the >>|/|<< Buttons......................12
4.5 Select Chapter/Track with the Number Buttons.........................................12
4.6 Select Chapter/Track with the Root/PBC Menu.........................................12
4.7 Terminate the Playback..........................................................................13
Video Specification
Video Type...................................................................16:9 and 4:3
Video Output level......................................Composite:1.0± 0.2Vp-p
Load impedance: 75 ohms
5. Advanced Disc, USB or MMC/SD Operation...................................................13
5.1 Playback with Speed..............................................................................13
5.2 Playback with Slow Speed......................................................................13
5.3 Playback with Still Frame.......................................................................14
5.4 Playback Repeatedly.............................................................................14
5.4.1 One/All Repeat...................................................................................14
5.4.2 A-B Repeat.........................................................................................14
5.5 Playback in Scan Mode..........................................................................15
5.6 Playback from a specified Chapter/Track or a Specified Time....................15
5.7 Playback in Random..............................................................................15
5.8 Playback in Different Angle.....................................................................15
5.9 Playback in Zoom Mode.........................................................................15
5.10 Change the Caption Language..............................................................16
5.11 Change the Audio Language.................................................................16
5.12 Change the Video Signal System..........................................................16
5.13 Look over the Playback Status..............................................................16
5.14 Program Playback...............................................................................17
5.15 Playback the Picture CD in JPEG Format...............................................17
5.16 Mp4 OPERATION................................................................................18
5.17 ESP and ID3 Function..........................................................................18
5.18 USB and MMC/SD Reader Operation.....................................................18
5.19 The DVD System Menu Setup Operation................................................18
5.20 The Parental Control............................................................................22
5.21 The Region Code.................................................................................23
Horizontal Resolution................................................................500
Audio Specification
Audio Output(Analog audio)..........................................2.0+0-1.0 Vrms
Frequency Response.............................20Hz ~ 20KHz(at 1KHz 0 dB)
S/N Ratio(Audio).............................................≥90dB(at 1KHz 0 dB)
Separation..............................................................................50dB
Radio Specification
FM Section
Frequency range..............................................87.5MHz - 107.9MHz
Usable sensitivity......................................................................3uV
I.F Frequency....................................................................10.7MHz
AM Section
6. The Trouble Shooting...................................................................................24
7. Specification...............................................................................................25
Frequency..........................................................530KHz - 1710KHz
6. The Trouble Shooting
1. Before Operation
1.1 Glossary
Please read the user’s manual carefully before using the DVD player. If you have any troubles
in using this player, try to solve the problems by the suggestions mentioned below. If you can
not remove the trouble after using all the suggestions, please contact the company or the
technical service center authorized by us. For the sake of your safety, please do not open the
cover and repair the player by yourself, if that, it may cause electric shock.
PBC (playback control)
It is a kind of signal(menu) recorded in the disc with SVCD or VCD2.0
format used for the playback control. For the discs contained PBC, It can
playback interactive software with the menu displayed on monitor screen.
If the disc contain still images, it can playback high definition of still image.
NO PICTURE, SOUND AND INDICATION
*
*
*
*
Ensure that the power switch is on.
Ensure that the wall inlet is ok.
Ensure that the power cord is not damaged or the fuse is not blown.
Ensure that the power plug is connected to the inlet tightly.
NO SOUND BUT HAVE PICTURE
Title
*
*
*
*
*
Ensure that the player’s audio output has a good connection with monitor’s audio input.
Check whether the audio connector is damaged.
Check whether you have turned down the volume.
Ensure that you have set the right AUDIO setup of the player.
Generally, the title is the important part of DVD disc. for example, the
theme part of movie is title 1, the part described how to make movie is title
2, the cast is title 3, etc. Every title contain a serial number that is easy to
look up.
Ensure that the audio is not under mute.
NO PICTURE BUT HAVE SOUND
Chapter
*
*
*
*
Ensure that the player’s video output has a good connection with monitor’s video input.
Ensure that you have turned your monitor to the AV input channel connecting to your player.
Check whether the video connector is damaged.
A title can be divided into several blocks, so that every block can be operated
as a unit, the unit is called chapter. The chapter contain a unit at least.
Ensure that you have set the right VIDEO settings of the player.
Track
BLACK AND WHITE PICTURE OR SCREEN ROLLING
Ensure that you have set the right TV SYSTEM (e.g. PAL, NTSC) setting.
*
It is the biggest component of VCD. Generally, every song of karaoke disc
is a track.
FLAWS OF PICTURE OR SOUND
*
*
*
*
Check whether the setting of AUDIO is right.
Check whether the disc is scratched or stained.
Check whether the AV connector and the output terminal is stained.
Check whether there is condensation inside the Lens. If so, leave the player off for an hour
or so, then try again.
PROTECTIVE CASE
1.2 Precautions
Safety
*
Check whether the installation angle is less than 30°.
DISPLAY NO DISC OR BAD DISC
FRONT PANEL
*
*
*
*
*
*
Ensure that you have put the disc on the tray.
Check whether the disc is put in the reverse side.
Check whether the disc is distorted.
Check whether the disc is stained or scratched badly.
Ensure that the disc format is compatible to the player.
Ensure that the temperature inside the car is not too high. If so, cool off till the ambient
temperature returns to normal.
1. Power Source: The unit should be connected to power supply only of
the type described in the operating instructions or as marked on the unit.
2. The unit is designed for negative terminal of the battery which is
connected to the vehicle metal. Please confirm it before installation.
3. Do not allow the speaker wires to be shorted together when the unit is
switched on. Otherwise it may overload or burn out the power amplifier.
4. Do not install the detachable panel before connecting the wire.
5. The protective case is to safely keep the front panel(see the photo).
*
Replace another disc to insert it into the disc compartment.
REMOTE CONTROL IS INSENSITIVE OR DOES NOT WORK
*
Check the batteries of remote control and make sure that they are to be powerful and
good conductivity.
*
*
Direct the remote control to the IR sensor of the player.
Check whether there are some obstacles between the remote control and IR sensor.
Environment
1. Do not use this unit when water and moisture is near it.
2. If moisture forms inside the Lens, it may not operate properly. To correct
this problem, wait about one hour for the moisture to evaporate.
3. If the car interior is extremely hot, do not use the player until the car has
been driven for a while to cool off the interior.
SOME FUNCTION BUTTONS DO NOT WORK
*
*
*
Turn off the power, then turn on again.
Reset the unit to zero, then turn on again.
Remove the front panel from the unit, then install it again and then turn on again.
THE RADIO DOES NOT WORK
Check whether the antenna cable is connected firmly. Or manually tune for a station.
*
1.3 Maintenance and Cleaning of Discs
Disc Maintenance
5.21 The Region Code
Q: Not begin to playback but to display REGION ERROR after inserting disc into
disc compartment. Why ?
1. To keep the disc clean, handle the disc by its edge, do not touch the disc
surface of the play side.
2. Do not stick paper or tape on the disc. If there is glue (or analog) on the
disc surface, must wipe it up before using.
3. Do not expose the disc to direct sunlight, or nearby heat sources such as
caliduct, or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
A: Because the DVD player and disc has respective region code. If the region codes
of them are not match with each other, the DVD player can not play the disc.
4. Put the disc inside disc case to keep temperature after finishing playback.
Appendix: The region code of DVD:
Disc Cleaning
The Motion Picture Association of America (MPAA) divided the world into 6
regions, and named every region a code, namely region code. The region codes
and the countries or areas represented by the region codes as follows:
1. Before playing, wipe the disc with a clean lint. wipe the disc outwards from
the disc center.
2. Do not use petrel, thinner. commercially cleaner or anti-static spray can
damage the unit.
Region 1: America, Canada, East-Pacific Inlands;
Region 2: Japan, West Europe, North Europe, Egypt, South Africa, Middle East;
Region 3: South-east Asian countries include Taiwan, Hong Kong, South Korea,
Thailand, indonesia, etc.;
Region 4: Australia, New Zealand, Central South America, South Pacific Inlands;
Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe, North
Korea, North Africa, North-west Asia etc.;
+
side up
B
A
Region 6: China mainland.
Fig.1
Fig.2
Fig.3
Basically, when a DVD movie disc for the version of region 6 was decided not to
issue, we need to purchase another DVD player that can play the DVD movie disc
for the version of non-region 6. In order to view this disc, viewer who does not have
the non-region 6 DVD player facilities will have to spend extra sum of money to buy
it. The problems caused from the area code inconsistency between the disc and the
DVD player has pushed for the production of Unlock-Version DVD player facilities,
and some DVD disc sets allow user to modify the area codes for a limited number of
times. But note that only the discs produced by the 8 biggest filmmaking companies
of America restrict so, they are not one of original DVD format. That is to say, the
DVD movie discs not produced by the 8 biggest filmmaking companies of America
were not restricted by the rule of region code. Generally, they are called
FreeRegionCode discs or Full Region discs. The 8 biggest filmmaking companies
of America are as follows:
1.4 Battery Information of the Remote Control
Replace Battery in the Remote Control:
1.Before using the remote control for the first time, pull the insulating
sheet out of the remote control as the direction indicated by the
arrow.(see fig.1)
2.Press the movable block hold as the direction indicated by the A arrow
(See fig.2), then pull the battery holder out of the remote control as
the direction indicated by the B arrow(see fig.2).
3.Replace the old battery by a new battery with (+) polarity side upward.
(See fig.3).
4.Insert the battery holder to the original position in remote control.
(See fig.3).
Note about the Battery of the Remote Control:
1.Improper use of battery may cause overheating or explosion. so that
Result in injury or fire .
2.Battery leakage may cause damage to the remote control(Battery
Life: 6 months with normal use in normal room temperature).
3.Do not short the battery.
1. WarnerBros;
2. Columbia;
3. 20thCenturyFOX;
4. Paramount;
5. Universal;
6. UA(UnitedArtist);
7. MGM(MetroDogwynMayer);
8. WaltDisney
4.Do not throw the battery into the fire.
5.To avoid the risk of accident, keep the battery out of reach of children.
1.5 The Remote Control Description
5.20 The Parental Control
3
27
1
35
1. TILT BUTTON
2. MENU BUTTON
3. POWER BUTTON
4. ^ BUTTON
Q:After inserting DVD disc into disc compartment, it will appear a dialogue window
that ask me input a password of 4 digit. Why ?
PWR
P/N
EQ
BAND
4
14
A:This is because that the disc movie you are playing was rated with the Parental
Control, and the current rating level of DVD player is lower than one of current
disc. You must input right password and enter it to entry Parental Control setup
menu and then set a equal or higher rating level than one of current disc. So that
you can playback the disc.
2
MU
MODE
MENU
29
32
9
33
SEL
0K
6
8
5. >>| BUTTON
34
13
SETUP
+
6. > BUTTON
5
7
!
NOTE
31
30
7. |<< BUTTON
8. v BUTTON
10
11
12
1
2
+10
4
8
3
7
*
For the factory preset password of the DVD player, please refer to the relative
content of PASSWORD setup menu for details.
-10
5
6
9. SEL BUTTON
10. PLAY/PAUSE BUTTON
*
For the rating level setup of Parental Control of the DVD player, please refer to
the relative content of LOCK setup menu for details.
CLK
SLOW_FWD
LOC
0/10
10+
9
24
28
16
15
ST
SEARCH
APS
21
22
18
17
11. NUMBER(0~10,+10
-10) BUTTONS
12. 10+ BUTTON
ZOOM
A-B
INT
RPT
RDM
Accessories: Parental Control
26
25
23
AUDIO
TITLE/PBC
SUBTITLE
19
20
The Parental Control function of a DVD player can control the playback of movie
rated level in a disc. Can set the DVD player(include software player in PC) to be a
certain rating level with SETUP MENU on monitor screen. If the rating level set in the
disc is higher than one set in the DVD player, the DVD player can not playback the
disc. Sometimes the Parental Control sequences in some discs are different from
each other. The rating level setup can be protected by the password. Therein, if you
select Unlock item, the Parental Control function will be invalid, the content of disc
will be played totally.
13. SETUP BUTTON
14. MODE BUTTON
PROG
STEP
OSD
LOUD
15. APS BUTTON
28. LOC/SLOW-FWD BUTTON
16. SEARCH BUTTON
17. RDM BUTTON
18. RPT BUTTON
29. MUTE BUTTON
30. STOP BUTTON
31. VOLUME- BUTTON
32. < BUTTON
The disc movie can be designed as that the DVD player will playback the different
version of content of a same movie according to the different rating level set by
Parental Control. Depend on the DVD feature of seamless switching described above,
the scenes that are not fitting for children will be cleared or replaced by the other
fitting scene automatically.
19. SUBTITLE BUTTON
20. TITLE/PBC BUTTON
21. ANGLE/ST BUTTON
22. ZOOM BUTTON
23. AUDIO BUTTON
24. CLK BUTTON
All rating levels of Parental Control are as follows:
33. OK BUTTON
Unlock
34. VOLUME+ BUTTON
35. BAND AND P/N BUTTON
36. PROG BUTTON
37. OSD BUTTON
1
2
3
4
5
6
7
8
Kid Safe
G
PG
PG 13
PG R
R
NC 17
Adult
25. A-B BUTTON
38. LOUD BUTTON
39. STEP BUTTON
26. INT BUTTON
27. EQ BUTTON
1.6 Description of the Face of the Front Panel
HUE
22
9
10
13
8
11
12
14
6
5
2
7
It is for adjusting the hue of the video output.
SATURATION
It is for adjusting the saturation of the video output.
SHARPNESS
ANG
USB
DVD/VCD/CD/MP3/USB/MMC
3
RPT
1
2
INT
It is for adjusting the sharpness of the video output.
BND
_
UP
DN
CLK
EQ
3.8 " TFT
SEL
5.19.5 SPEAKER SETUP
+
APS
AUX
SPEAKER SETUP
DOWNMIX
MU
RDM
4
5
-10
6
+10
MODE
REL
EXIT SETUP
19
20
15
21
16
3
18
1
4
17
DOWNMIX
1. POWER/MUTE BUTTON
2. ANG(i.e. TILT) BUTTON
3. RELEASE BUTTON
4. MODE BUTTON
5. AUX IN SOCKET
6. SEL BUTTON
8. IR REMOTE SENSOR
9. BAND BUTTON
10. UP and DN BUTTONS
11. EJECT BUTTON
12. 1/PLAY/PAUSE BUTTON
13. 2/INT BUTTON
16. 5/-10 BUTTON
17. 6/+10 BUTTON
18. USB SOCKET
19. RESET BUTTON
20. APS BUTTON
21. EQ BUTTON
22. CLK BUTTON
It is for selecting your desired sound effect when there is not central speaker
and sub-woofer. There are 3 mode: LT/RT, STEREO, VSS.
LT/RT: When playing a disc with PRO LOGIC Dolby stereo effect, choose the
item, so it will output audio signal with vivid theatre effect.
AND VOL KNOB
14. 3/RPT BUTTON
STEREO: If you choose the item, when outputting audio signal with 5.1 channels,
it will output the left and right channels of signal ; when outputting audio signal
with 2 channels, it will output the common 2 channels of stereo signal.
VSS: If you choose the item, when playing a disc recorded with 5.1 channels,
the main channel speakers can output audio signal with VSS effect.
7. SMALL MONITOR
15. 4/RDM BUTTON
1.7 Description of the Unit Chassis Facet After removing the Front Panel
26 PIN FEMALE CONNECTOR
5.l9.6 DIGITAL SETUP
DIGITAL SETUP
OP MODE
DYNAMIC RANGE
DUAL MONO
EXIT SETUP
TAMPON-PICK
OP MODE
26 PIN FEMALE CONNECTOR: when there is some dirt on the connector,
It is for selecting audio output mode
please wipe it away from the connector.
LINE OUT: It can linearly compress the audio signal. So the volume level is lower.
You should select the item at night.
RF REMOD: It can make the volume level higher. You should select it at daylight.
DYNAMIC RANGE
1.8 Description of the Unit Chassis Facet After Sliding Down the Front Panel
After selecting the compression mode of LINE OUT, set the item, so you can
adjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peak
value of the audio signal is the minimum; if you set it to be OFF, the Peak-to-
Peak value is the maximum.
DUAL MONO
It is for selecting a desired audio output mode for the left and right ways of signal.
It is mainly for Karaoke of Ac3. There are 4 modes in all as follows:
STEREO, MONO L, MONO R, MIX MONO.
LED indicators
* The LED indicators light all the time, they can help you operate during darkness.
5.19.2 LANGUAGE SETUP
1.9 Description of the Rear Cabinet
LANGUAGE SETUP
Fixing Screw Bolt
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
Reversal line Orange
Parking Line Brown
MENU LANG
EXIT SETUP
OSD LANGUAGE
This item is for selecting the language of the SYSTEM MENU and all operating
prompt interface displayed during playback.
AUDIO LANG
YELLOW
YELLOW
GRAY
GRAY
WIRING CONNECTING SOCKET
VIDEO OUT
This item is for selecting a audio language.
SUBTITLE LANG
Note: 1. after connecting the Parking Line, the video on the small monitor of the front panel will be display only after braking the car.
2. Use the clip end of a Ground Line provided by manufacturer to connect the Fixing Screw Bolt, use another end of the Ground
Line to connect the negative pole of the power source. Otherwise, the video on screen maybe flashes.
This item is for selecting a subtitle language.
MENU LANG
This item is for selecting a disc menu language.
Connecting the parking brake line to the parking brake system built in the car
Parking brake
5.l9.3 AUDIO SETUP
AUDIO SETUP
Parking brake line(light blue)
AUDIO OUT
KEY
Parking brake switch
(inside the car)
To metallic body or chassis of the car
EXIT SETUP
AUDIO OUT
there is only ANALOG mode, i.e. SPDIF/OFF, not optional.
KEY
It is for selecting your desired basic music tone(from low to high).
1.10 Description of Wires Harmness
WIRING CONNECTING SOCKET
WIRING CONNECTING PLUG
5.l9.4 VIDEO SETUP
VIDEO SETUP
YELLOW
WOOFER LINE OUT(optional)
GREEN
MEMORY B+
FUSED
FILTER
BOX 1A
& 10 A
BRIGHTNESS
CONTRAST
HUE
SATURATION
SHARPNESS
BLACK(GND)
RED
RED R
FUSES
IGNITION SWITCH
RCA LINE OUT
WHITE L
FRONT
BLUE AUTO ANT
WHITE
GRAY
FRONT
WHITE / BLACK
GREEN
GRAY / BLACK
VIOLET
RIGHT
SP
LEFT
SP
EXIT SETUP
REAR
BRIGHTNESS
REAR
VIOLET / BLACK
GREEN / BLACK
It is for adjusting the brightness of the video output.
CONTRAST
It is for adjusting the contrast of the video output.
NOTES:
1. Only speakers with 4 ohms impedance may be used.
2. Ensure that the blue auto antenna cable does not make contact
with any ground connection.
For the DVD System Menu, there are 6 setup pages in all. They display as follows:
5
.19.1 SYSTEM SETUP
1.11 UNIT INSTALLATION
SYSTEM SETUP
TV SYSTEM
TV TYPE
INSTALLATION INSTRUCTIONS
PASSWORD
RATING
DEFAULT
TO BOOST UP THE CAPABILITY OF
ANTI-JAMMING, PLEASE FIX THE
METAL STRAP ON THE METAL
CONNECTED TO THE BOTTOM
BRACKET OF THE CAR.
SELECT THE PROPER FIXER
FOR FIXING THE SLIDING
METAL HOUSING.
EXIT SETUP
METAL STRAP
TV SYSTEM
This product supports output of various TV system, including PAL, PAL-M, PAL-N,
NTSC and AUTO.
If your TV set has only NTSC or PAL system, the screen will blink and become
colorless when a wrong TV system is selected. In this case, press the N/P button
to switch the right TV system to match the TV color system.
TV TYPE
UNIT CHASSIS
DASH BOARD
PLASTIC TRIM OUT
FRONT PANEL
SLIDING METAL HOUSING
The setup item is for matching TV screen size.
4:3 PS: Choose the item when connecting a TV set with 4:3 screen. When playing
the pictures with 16:9 size, the left and right parts of the video will be cut out,
and display in full screen.
4:3 LB: Choose the item when connecting a TV set with 4:3 screen. When playing
the pictures with 16:9 size, the top and bottom parts of the TV screen will be
turned into a black square respectively.
TO DRAW THE CHASSIS OUT OF THE
SLIDING METAL HOUSING, INSERT
THE LEFT AND RIGHT KEY PLATES
INTO THE RIGHT POSITION OF THE
2 SIDES OF CHASSIS.
16:9: Choose the item when connecting a TV set with 16:9 wide screen.
PASSWORD
This setup item is for locking or unlocking the rating level of the Parental Control.
The defaulted state is locked. The defaulted password is 0000.
You can set a new password that you like: Select the PASSWORD item and then
press the > button to enter it, then input the original password 0000, and then
press the OK button to unlock it. Press the > button to enter it again, then input
a new password that you like and then press the OK button to make it effective.
Before the other persons see the Manual, you should get the password in mind
and cut out the part of PASSWORD in the Manual.
NOTE
REMOVE THE DECK TRANSPORT
SCREWS BEFORE INSTALLING IT.
RATING
The item is for setting a new rating level of the Parental Control.
1. Select the PASSWORD item and then press the > button to enter it, then input
the password mentioned above, and then press the OK button to unlock the
setting of the rating level of the Parental Control.
2. Select the RATING item and then press the > button to enter it, then use the
direction buttons to select your desired rating level, then press the OK button
to confirm.
TO INSTALL THE FRONT PANEL
BACK INTO THE PANEL HOUSING,
FIRSTLY INSTALL THE LEFT SIDE
BACK INTO THE RIGHT POSITION,
THEN PUSH THE RIGHT SIDE BACK
TO THE PANEL HOUSING TILL IT
CLIP INTO THE POSITION.
3. Select the PASSWORD item again and then press the > button to enter it, then
input the password, and then press the OK button to lock the new setting of
the rating level of the Parental Control.
DEFAULT
This item is for making all setup items change back to original status.
3. During JPEG playback, press one of the >/</^/v buttons to change the angle of
viewing picture that is displaying as follows:
2. Common Operation
>: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHT
During JPEG playback, press the PROG button to change the mode of refresh picture.
During JPEG playback, press the STOP button to stop playing and return to the root
menu.
During JPEG playback, the following buttons are not available: SLOW-FWD,
SUBTITLE, TITLE, ANGLE, STEP, SEARCH, INT and A-B.
1. To turn on/off the unit
Under power off mode, press the POWER button to turn on the unit.
Under power on mode, long press the POWER button on the front panel or
briefly press the POWER button on the remote control to turn off the unit.
2. To select function mode
*
*
In JPEG mode,the other operations are same as ones in MP3/WMA mode.
Press the MODE button to select TUNER, DISC(After inserting a disc), USB
(After inserting a USB storage), Card(After inserting a MMC or SD card) or
AUX mode.
5.16 MP4 Operation
3. To adjust sound level
1. The root menu is displayed on monitor when beginning to switch on DISC mode, then
it will automatically play the first file.
Rotate the VOL knob on the front panel or press or hold the + or - button on
the remote control to directly adjust the volume level.
4. To mute sound
During playback, press the STOP button to stop playing and return to the root menu.
2. When displaying the root menu, press the direction buttons to select your desired
FOLDER or file, then press the OK or PLAY button to open the FOLDER, or play the
selected file.
Press the MUTE button on the remote control to turn on/off MUTE mode.
Briefly pressing the POWER button on the front panel also can turn on/off
MUTE mode.
When displaying the root menu, you can also use the number buttons to select the
serial number of the file and play the file.
In MUTE mode, the MUTE mode can be released by pressing the following
buttons: MUTE, EJECT, VOL or +/-, SEL, POWER(on the front panel), MODE.
5. To display and adjust the clock time
*
*
The ANGLE, PROG, RDM, INT and TITLE/PBC button are not valid.
The other functions are same as ones in DVD disc; but the RPT function is same as
one in MP3/WMA.
Press the CLK button to display clock time on the small monitor of the front
panel.
5.17 ESP and ID3 Function
Then long press the CLK button to change the color of the hour of the clock,
then rotate the VOL knob on the front panel or press the + or - button on the
remote control to adjust the hour; and then briefly press the SEL button to
change the color of the minute of the clock, then rotate the VOL knob on the
front panel or press the + or - button on the remote control to adjust the
minute.
There is ESP function for all formats of discs.
In MP3/WMA mode, during playback, the information of the file name, folder name,
song s title, artist and album will be scrolling on the LCD display. As long as the
current playing MP3 music contains relevant ID3 tag information in version 1.0/2.0
format, the 3 items underlined above will be scrolling on the LCD display; otherwise,
they will not.
6. To select a preset EQ mode
Press the EQ button to select the preset music equalizer curves: POP, ROCK,
CLAS, FLAT . The sound effect will be changed.
7. To remove the front panel
Press the RELEASE button on the front panel to detach the front panel from
the unit, then you can remove the front panel.
8. To select a optimal angle of the front panel
5.18 USB and MMC/SD Reader Operation
Power on the DVD player, then insert the USB storage or MMC/SD Card, and then the
monitor will display the root menu of the USB storage or MMC/SD Card.
All the operations are same as ones of the corresponding format.
When you want to insert a Card, need to tilt the front panel to an appropriate degree;
When you want to pull out the Card, firstly push it, and then pull it out.
Press the TILT button repeatedly to select a optimal angle as follows:
-->ANGLE0-->ANGLE1-->ANGLE2--> ANGLE3--> ANGLE4-->
9. To turn on/off LOUD mode
Card socket
SD/MMC
Press the LOUD button on the remote control to turn on/off LOUD mode.
When turning on LOUD mode, it will enhance bass level immediately when
the bass is not enough.
The top side of the front panel
10.To reset the unit
5.19 The DVD System Menu Setup Operation
1. Press the SETUP button on the remote control to access the DVD System Menu on
the monitor.
2. There are 6 setup pages in all for the System Menu. Press the > or < button to select
an desired setup page.
3. Press the ^ or v button to select an setup item in the selected setup page.
4. Press the > button to enter the setup item. Then press the v or ^ button to select a
desired mode of the setup item, finally press the OK button to confirm it.
Press the RESET button to rehabilitate the distorted program to zero when
the display is wrong or the function buttons are not effective.
11.To adjust the sound equalizer curves
To adjust the sound equalizer curves, briefly and repeatedly press the SEL
button to select the sound equalizer curves of VOL, BAS(without preset EQ),
TRE (without preset EQ), BAL, FAD, then rotate the VOL knob on the front
panel or press the + or - button to adjust level.
*
Press the < button to return to the upper level.
*
Press the SETUP button again or use the direction buttons to highlight the item of the
EXIT SETUP and then press the OK button to exit the System Menu.
5.14 Program Playback
3. Radio Operation
It allows you to enter the order in which you want some chapters/tracks in
DVD/VCD/MP3/WMA/CD disc to play.
1 During playback, press the PROG button to enter a program interface as
follows:
1. BAND BUTTON
In RADIO mode, press the BAND button on the remote control or on the front panel to
select your desired radio band of FM1, FM2, FM3, AM1 and AM2, and the word means which
band is selected will be displayed on the small monitor of the front panel.
for DVD discs
for VCD/MP3/WMA/CD discs
PROG
PROG
T
C
T
C
T
C
T
C
1__:__ 5__:__ 9 __:__13 __:__
2__:__ 6__:__ 10__:__14__:__
3__:__ 7__:__ 11__:__15__:__
4__:__ 8__:__ 12__:__16__:__
1____ 5 ____ 9____ 13 ____
2____ 6 ____ 10____ 14 ____
3____ 7 ____ 11____ 15 ____
4____ 8 ____ 12____ 16 ____
2. TUNE/SEEK UP/DOWN BUTTONS
In RADIO mode:
1) Long press the UP/DN button on the front panel or the >>|/ |<< button on the remote control
to automatically search up/down for a available station from the current frequency.
2) Briefly press the UP/DN button on the front panel or the >>| / |<< button on the remote control
to manually search up or down with step by step for your desired station from the current
frequency.
Play
Clear
Play
Clear
2 Use the direction buttons to move cursor onto the desired place for inputting
the sequence number.
3. APS BUTTON
3 Use the number button to input desired sequence number of title/chapter/
track with desired sequence.
4 Use the direction button to move cursor onto Play item, then press the OK
button to play the programmed titles/chapters/tracks in programmed order;
only pressing the PLAY button also can play the programmed titles/chapters
/tracks in programmed order.
In RADIO mode:
1) When long pressing the APS button, the radio searches from the lowest frequency and checks
the signal strength level until 1 cycle search is finished. And then the 6 strongest stations are
preset to the corresponding preset number memory bank. The AS operation is implemented in
the each bank of the selected band. When the AS operation is finished, it will resume broad-
casting on the M1.(It can store 3x6 stations for FM and 2x6 stations for AM in all)
2) When briefly pressing the APS button , the radio searches for each preset station from the M1.
When the field strength level is more than the threshold level of the stop level, the radio is holding
at that preset number for few seconds with releasing mute, and then searches again. After finishing
a circle of searching, it will stop searching on the M1.
*
*
*
*
To exit program playback, firstly press the STOP button, then press the PLAY
button to enter sequence playback; or press the PROG button twice again.
To remove the all programmed sequence numbers, move the cursor onto
Clear item, then press the OK button.
To change the programmed sequence, move the cursor onto the item you
want to change, input the desired sequence number.
NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.
In AM band, AM1, AM2 is checked one at a time.
During VCD playback, if it is in PBC ON mode, at the same time of entering
the state of program playback, it turns off PBC mode.
4. PRESET STATION [ 1-6 ] BUTTONS
In RADIO mode:
1) To memorize the current frequency on the current band, long press any one of the six preset
buttons (1-6) .
5.15 Playback the Picture CD in JPEG Format
2) To recall the preset memory on the current band, press one of the preset buttons [1-6] .
1. The root menu is displayed on the monitor when beginning to switch on DISC
mode. At the time, it plays MP3/WMA file.(the TITLE or MENU button is not
available).
5. STEREO/MONO BUTTON
Press the ST button on the remote control to select the STEREO or MONO sound mode for
FM band.
In the root menu, the left file sort icon is for MP3/WMA file; the middle file sort
icon is for JPEG file; the right file sort icon is for VIDEO file. If one of these 3
file sort does not exist, you can not move cursor onto the file sort icon.
2. When displaying the root menu, press the direction buttons to select your
desired FOLDER, file or file sort icon, then press the OK or PLAY button to
open the FOLDER, or play the selected file, or play only this sort of file.
When displaying the root menu, you can also use the number buttons to
select the serial number of the file and play the file.
6. LOC BUTTON
1) In RADIO mode, when the signal of the distance radio station are very weak and the receiving
effect is bad during tuning, check whether there is the word LOC on LCD. If there is the word
LOC on LCD, press this button to turn off the LOC function, then tune again for the distance
radio station;
2) In RADIO mode, when the signal of the local radio station are too strong to lead that the
interference to the receiving effect during tuning, press this button to turn on the LOC function
to display the word LOC on LCD, then tune again for the local radio station.
When you select a JPEG file sort icon, press the ^ or > button to select the
first JPEG file, then press the v button to select the desired JPEG file, finally
press the OK or PLAY/PAUSE button to display the JPEG picture in full screen
from the selected JPEG picture.
ZOOMx2,ZOOMx3,ZOOMx4,ZOOMx1/2,ZOOMx1/3,ZOOMx1/4,ZOOM OFF.
Press one of the ^/v/>/< buttons to select the area you want to enlarge.
4. Basic Disc, USB or MMC/SD Operation
4.1 Begin playback
5.10 Change the Caption Language
In the state of DVD disc playing, press the SUBTITLE button repeatedly to
select the language of the caption or turn off the caption.(depend on the
disc used.)
1. Press the POWER button briefly to turn on the DVD player.
After turning on the DVD player, please turn on the monitor, and ensure that
the video output of the monitor is the video input from the DVD player
connected with the monitor.
In the state of VCD/MP3/WMA/CD disc playing, the button is not available.
?
Common Question
5.11 Change the Audio Language
Q: There is not anything is displayed on TV screen when the DVD player is
turned on. How to solve the problem?
1. In the state of DVD disc playing, press the AUDIO button repeatedly
on the IR remote control to select the desired language type.
(depend on the disc used)
2. In the state of VCD disc playing, press the AUDIO button repeatedly to
select the sound mode of the MONO L, MONO R, and Stereo, no language
function.
A: Ensure that the TV was set to right video input(not TV channel); for
example, if you make VIDEO1 INPUT of TV and DVD player connected
with each other, then you need set TV to VIDEO1.
2. Press the EJECT button to slide down the front panel.
3. In the state of CD/WMA/MP3 disc playing, the AUDIO button is invalid.
3. Insert a disc into the Disc Compartment(Label surface up), then the
front panel will slide back to the previous angle.
5.12 Change the Video Signal System
During playback of DVD/VCD disc, press the BAND(P/N) button on the front
panel or on the remote control repeatedly to change the VIDEO SIGNAL
SYSTEM mode as follows:
--> PAL--> PAL-M --> PAL-N --> NTSC --> AUTO -->
! NOTE
5.13 Look over the Playback Status
1. For some discs that are seriously scratched or poor manufacturing or
recording quality, it may not play.
1. In the state of DVD disc playing, press the OSD button repeatedly on the
remote control to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing title, the
serial number of the playing chapter, the elapsed time of the playing chapter,
the remained time of the playing chapter, the elapsed time of the playing title,
the remained time of the playing title, etc.
2. If the player can not read disc under normal condition, please try to
eject and reload the disc again.
3. Remark:
2. In the state of VCD/CD disc playing, press the OSD button repeatedly on the
remote control to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track, the
elapsted time of the disc, the remained time of the disc.
1) In addition to normal CD and DVD, this unit supports to play CD-R,
CD-R/W, DVD-R and DVD-R/W as well; however, depending on the
conditions of the recording equipment, recording program or the disc
itself, some CD-R, CD-R/W, DVD-R or DVD-R/W may not play.
3. In the state of MP3/WMA disc playing, press the OSD button repeatedly on
the remote control to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track.
2) When dealing with CD-R, CD-R/W, DVD-R or DVD-R/W recording,
too high recording speed may result in poor signal quality and therefore,
it is recommendable to select as lower as possible recording speed.
5.5 Playback in Scan Mode
4.2 Pause Playback
1. In the state of VCD(PBC OFF)/CD disc playing, press the INT button to play
the previous 10 seconds part of each track on the disc. Press the INT button
again to resume normal playback.
In the state of DVD/VCD/CD/MP3/WMA disc playing, press the PAUSE
button on IR remote control to pause the playback, press the PLAY
button to resume normal playback.
2. In the state of DVD/MP3/WMA disc playing, the INT button is not available.
5.6 Playback from a specified chapter/track or a specified time
4.3 Stop Playback
In the state of DVD/VCD/MP3/WMA/CD disc playing, press the STOP button
once to pause the playback, then press the PLAY button to resume the normal
playback; press the STOP button twice to full stop the playback, then press
the PLAY button to start playback from the beginning of the first chapter/track.
1. In the state of DVD disc playing, press the SEARCH button to display a
interface and highlight the title item, then use the number buttons to input
the serial number of the title; use the direction buttons to highlight the chapter
item, then use the number buttons to input the serial number of the chapter;
you can still use the direction buttons to highlight the time item, then use the
number buttons to input the desired time to start playback; finally press the
OK or PLAY button to play the selected chapter or play from the selected time.
4.4 Select Chapter/Track with the UP/DN or the >>| / |<< Button
Press the UP/DN button on the front panel or the >>| / |<< button on the
remote control during playback to select the next or last chapter/track to
playback.
2. In the state of VCD/MP3/WMA/CD disc playing, press the SEARCH button to
display a interface and highlight the track item, then use the number buttons
to input the serial number of the track; you can still use the direction buttons
to highlight the time item, then use the number buttons to input the desired
time to start playback; finally press the OK or PLAY button to play the selected
track or play from the selected time.
Note: Press the UP/DN or the >>|/|<< button multiple times to advance
multiple chapters/tracks forward or backward.
4.5 Select Chapter/Track with the Number Buttons
In the state of DVD/VCD(PBC OFF)/MP3/WMA/CD disc playing, press one
of the 1~9 and the 0/10 number buttons to directly select and play the 1st to
10th track/chapter (the 0/10 button is used as the 10 button).
If you want to play the track/chapter that s serial number is bigger than 10,
use the 10+, 1~9 and 0/10 button. For example 1, to play the 13th track/
chapter, firstly press the 10+ button once, then press the 3 button. For
example 2, to play the 34th track/chapter, firstly press the 10+ button for 3
times, then press the 4 button.(the 0/10 button is used as the 0 button)
Note: long pressing the +10 or -10 button can play the next 10 or last 10
chapter/track(only for MP3/WMA).
5.7 Playback in Random
In the state of DVD/VCD(PBC OFF)/MP3/WMA/CD disc playing, press the
RDM button to switch between RANDOM (ON)/RANDOM OFF. When in
RANDOM (ON) mode, it will play in random.
5.8 Playback in Different Angle
4.6 Select Chapter/Track with the Root/PBC Menu (If the disc includes the
root/PBC menu)
1. In the state of VCD/MP3/WMA/CD disc playing, the ANGLE button on the
IR remote control is not available.
In the state of DVD disc playing
2. In the state of DVD disc playing, press the ANGLE button repeatedly on
the IR remote control to view in different angle.(This function is only
for the DVD discs with ANGLE function)
1. Press the TITLE button on the remote control to display the title list.
2. Press the direction buttons to select your desired title, and then press the OK
or PLAY button to open the root menu of the selected title.
3. Press the direction buttons to select your desired chapter, finally press the
OK or PLAY button to play the selected chapter.
5.9 Playback in Zoom Mode
During playback, pressing the MENU button can directly display the root
menu of the title that is playing.
In DVD/VCD mode, during playback, press the ZOOM button continuously
to enlarge a certain area of the images on the screen with these multiples:
During slow forward, press the PLAY button to resume normal playback.
The function is only for video.
In VCD mode
1. When starting to turn on the PBC function, it will play from the beginning of
the disc till it display the PBC menu on monitor screen if the disc include the
PBC menu.
5.3 Playback with still frame
2. Press the number buttons to select your desired track to play.
If the unit is currently running DVD/VCD disc, press the STEP button
consecutively to display the still frame forward with step by step.
In MP3/WMA mode
1. The root menu is displayed on the monitor screen all the time(and the TITLE
Press the PLAY button to resume normal playback.
or MENU button is not available).
2. Press the direction buttons to select your desired FOLDER, then press the
OK or PLAY button to open the FOLDER, and then press the direction buttons
to select your desired file, finally press the OK button to play the selected file.
5.4 Playback Repeatedly
5.4.1 ONE/ALL Repeat
In CD mode, the TITLE, PBC, MENU buttons are disabled.
1. In the mode of DVD disc playback:
Press the RPT button to select RPT CHAPTER, RPT TITLE and RPT
ALL.
4.7 Terminate the Playback
1. Press the EJECT button to slide down the front panel, then the disc in the disc
compartment will come out automatically. and then remove the disc away.
2. In the mode of VCD(PBC OFF)/CD disc playback:
press the RPT button to select RPT 1, RPT ALL.
When it is in the state of PBC ON, during VCD disc playing, the RPT
button are not available.
2. Long press the POWER button on the front panel or briefly press the POWER
button on the remote control to turn off the DVD player.
3. In the mode of MP3/WMA disc playback:
Press the RPT button to select RPT 1, RPT DIR, RPT ALL.
5. Advanced Disc, USB or MMC/SD Operation
5.1 Playback with Speed
5.4.2 A-B Repeat
During normal playback, long press the UP/DN button on the front panel or
the >>|/|<< button on the remote control continuously to fast forwards
or backwards at the following speeds: x2, x4, x8, x16, x20, normal.
Press the A-B button if you want to repeat a specific segment on a disc
that you define:
1. Press the A-B button at a point (A) where you want it to be the start point
of the repeat segment. Press the A-B button again at a point (B) where you
want it to be the terminal point of the repeat segment. Then it will play the
segment repeatedly.
During speed playback, press the PLAY button to resume normal playback.
5.2 Playback with Slow Speed
2. To cancel the A-B repeat mode and resume normal playback, press the A-B
During playback , press the SLOW_FWD button to execute the Slow
Forward function.
button for the third time.
Note:
With each consecutive pressing of the SLOW_FWD button, the playback
speed decreases. The speed levels in Slow Forward as follows:
x1/2,x1/3,x1/4,x1/5,x1/6,x1/7,normal.
During VCD/MP3/WMA/CD playback, points A and B must be within the
same track.
During DVD playback, points A and B can be selected from different chapters.
|