43-1032.fm Page 1 Tuesday, August 17, 1999 9:41 AM
Cat. No. 43-1032
OWNER’S MANUAL
Please read before using this equipment.
ET-532
10-Channel Cordless
Telephone with LCD Display
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 3 Tuesday, August 17, 1999 9:41 AM
This telephone has been tested and
found to comply with all applicable UL
and FCC standards.
Warning: To prevent fire or shock haz-
ard, do not expose this product to rain
or moisture.
Your ET-532 operates on standard ra-
dio frequencies, as allocated by the
FCC. Therefore, it is possible for other
radio units operating on similar fre-
quencies, within a certain area, to in-
advertently intercept your conversa-
tions and/or cause interference on
your cordless telephone. This lack of
privacy can occur with any cordless
telephone.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
For your records, we urge you to
record the serial number of your phone
in the space below. The serial number
is located on the bottom panel of the
base.
This symbol is intended to inform
you that important operating and
maintenance instructions are in-
cluded in the literature accompany-
ing this product.
Serial Number ______________
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 4 Tuesday, August 17, 1999 9:41 AM
READ THIS BEFORE
INSTALLATION
FCC STATEMENT
This telephone complies with Part 68
of FCC Rules. You must, upon re-
quest, provide the FCC registration
number and the REN to your phone
company. These numbers are located
on the bottom of your phone’s base.
We have designed your telephone to
conform to federal regulations, and
you can connect it to most telephone
lines. However, each device that you
connect to the phone line draws power
from the phone line. We refer to this
power draw as the device’s ringer
equivalence number, or REN. The
REN is shown on the bottom of your
phone’s base.
Note: You must not connect your
phone to any of the following:
• Coin-operated systems
• Party-line systems
If you are using more than one phone
or other device on the line, add up all
the RENs. If the total is more than five,
your phone might not ring. In rural ar-
eas, a total REN of three might impair
ringer operation. If ringer operation is
impaired, remove a device from the
line.
• Most electronic key phone sys-
tems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 5 Tuesday, August 17, 1999 9:41 AM
CONTENTS
Installation ............................................................................................................ 6
Selecting a Location ........................................................................................ 6
Installing the Phone ........................................................................................ 6
Preparation ........................................................................................................... 7
Installing the Battery ....................................................................................... 7
Charging the Battery ....................................................................................... 7
Setting the Dialing Mode ................................................................................. 8
Operation .............................................................................................................. 9
Making/Answering a Call ................................................................................ 9
Using the Handset at the Base ................................................................. 9
Using the Handset Away from the Base ................................................... 9
Reducing Interference ................................................................................... 10
Using Redial .................................................................................................. 10
Using Flash ................................................................................................... 10
Using Tone Services on a Pulse Line ........................................................... 11
Using Page ................................................................................................... 11
Memory Dialing ............................................................................................. 11
Storing a Number in Memory .................................................................. 12
Entering a Pause in a Memory Number ................................................. 13
Dialing a Stored Number ........................................................................ 13
Chain Dialing .......................................................................................... 14
Testing Stored Emergency Numbers ...................................................... 14
Troubleshooting ................................................................................................ 15
Care and Maintenance ...................................................................................... 17
Replacing the Battery .................................................................................... 18
The FCC Wants You to Know ....................................................................... 18
Lightning ....................................................................................................... 19
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 6 Tuesday, August 17, 1999 9:41 AM
INSTALLATION
SELECTING A LOCATION
INSTALLING THE PHONE
Select a location for the telephone that
meets these requirements:
Follow these steps to install the base
on a desk, shelf, or table.
• Near an AC outlet
• Near a telephone line jack
• Out of the way of normal activities
• Away from electrical machinery,
electrical appliances, and metal
walls or filing cabinets
• Away from wireless intercoms,
alarms, and room monitors
1. Plug one end of the supplied mod-
ular cord into the phone jack on
the back of the base.
The base’s location affects the phone’s
range. If you have a choice of several
locations, try each one to see which
provides the best performance.
2. Plug the modular cord’s other end
into a modular phone line jack.
3. Insert the supplied AC adapter’s
barrel plug into the DC 12V jack on
the back of the base.
If the phone line jack is not a modular
jack, you must update the wiring your-
self, using jacks and adapters avail-
able at your local Radio Shack store.
Or, you can let the phone company up-
date the wiring for you.
4. Plug the adapter into a standard
AC outlet.
For the best reception, fully extend the
base’s antenna and place it in a verti-
cal position.
Notes:
• The phone company will charge
you for the installation of the nec-
essary jacks.
Caution:
You must use a 120V AC/
12V DC adapter that delivers at least
200 milliamps. Its center tip must be
positive, and its plug must correctly fit
the phone’s DC 12V jack. The supplied
adapter meets these requirements.
Using an adapter that does not meet
these requirements could damage the
phone or the adapter.
• The USOC number of the jack to
be installed is RJ11C.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 7 Tuesday, August 17, 1999 9:41 AM
PREPARATION
INSTALLING THE
BATTERY
CHARGING THE
BATTERY
Before you use your phone for the first
time, you must install and charge the
battery.
When you install a new battery, set
POWER to OFF. Then place the hand-
set on the cradle so the CHARGE/
TALK indicator lights and let the bat-
tery charge for about 15 hours.
To install the battery, slide off the bat-
tery compartment cover on the back of
the handset, connect the battery’s plug
to the pins inside the compartment,
and place the battery inside the com-
partment.
When
on the handset lights, re-
charge the battery. To avoid damage
to the battery, always recharge the
handset before battery power grows
too weak to light
.
Replace the cover, then follow the in-
structions under “Charging the Bat-
tery.”
Notes:
• You can set POWER to ON while
the battery charges.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 8 Tuesday, August 17, 1999 9:41 AM
• If the CHARGE/TALK indicator
does not light when you place the
handset on the cradle, be sure the
battery is connected to the pins
inside the battery compartment
and the AC adapter is securely
connected to the base. Also,
check the charging contacts on
the handset and base. If the con-
tacts are dirty or tarnished, gently
clean them with a pencil eraser.
SETTING THE DIALING
MODE
Set TONE/PULSE on the back of the
base for the type of service you have.
If you are not sure which type you
have, do this test.
1. Set TONE/PULSE to TONE.
• About once a month, fully dis-
charge the battery by keeping the
handset off the cradle until
flashes, then return the
2. Lift the handset and listen for a
dial tone.
3. Press any number other than 0.
handset to the cradle and fully
recharge the battery. If you do not
fully discharge and recharge the
battery periodically, it loses its
ability to fully recharge.
4. If the dial tone stops, you have
touch-tone service.
If the dial tone continues, you have
pulse service. Set TONE/PULSE to
PULSE.
• The first time you use your phone
after installing a new battery, the
handset might not work and might
sound an error tone when you
press TALK. This might also occur
when you recharge a battery that
has been completely discharged.
If this happens, be sure the hand-
set is turned on, then return the
handset to the cradle for 5 sec-
onds. This resets the security
access code.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 9 Tuesday, August 17, 1999 9:41 AM
OPERATION
Your ET-532’s LCD display shows
telephone numbers as you dial them or
when you recall them from memory. It
shows the current channel number and
lets you know when battery power is
growing weak or the phone is out of
range of the base. The display also
shows indicators when you pres
FLASH or PAUSE, or when you switch
from tone to pulse dialing.
To make a call, lift the handset from
the base and press TALK so the key-
pad and the CHARGE/TALK indicator
on the base light.
Note: CH
and the currently used
channel number appear on the display.
This number might change when you
return the handset to the base.
MAKING/ANSWERING
A CALL
You can use your cordless telephone
in two ways: at the base or away from
the base.
To disconnect a call, replace the hand-
set on the base.
Using the Handset
Away from the Base
Using the Handset
at the Base
To make or answer a call, set POWER
to ON and press TALK. The keypad
and CHARGE/TALK indicator light.
You can use the handset at the base
like a regular corded telephone. Just
set POWER to ON and place the hand-
set in the cradle.
To disconnect a call, press TALK so
the keypad light and the CHARGE/
TALK indicator turn off.
Notes:
• CHand the currently used channel
number appear on the display.
• To conserve battery power, you
can turn off the handset’s power
when you are not making or
answering a call.
To answer a call, just lift the handset
from the base.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 10 Tuesday, August 17, 1999 9:41 AM
• You can make or answer a call on
a phone on the same line as the
cordless phone, even if the hand-
set is away from the base.
• RANGE appears when the dis-
tance from the handset to the
base is out of the phone’s range.
• The keypad lights on the handset
turn off if no button is pressed for
more than 13 seconds.
The redial memory holds up to 80 dig-
its in the tone mode or 81 digits in the
pulse mode. The redial memory also
holds pause entries (see “Entering a
Pause” under “Memory Dialing”).
REDUCING
INTERFERENCE
CH
To reduce interference, press
to
switch to the next channel (10 chan-
nels in all) until you receive the best re-
ception. CH and the channel number
appear on the display.
RE-
Note: We recommend you not use
DIAL
to dial numbers that include a
tone (*) entry (see “Using Tone Servic-
es on a Pulse Line”).
USING FLASH
FLASH
Use
on the handset to perform
the switchhook operation for special
services, such as call waiting.
USING REDIAL
To quickly redial the last number you
dialed, simply lift the handset from the
TALK
base and press
CHARGE/TALK indicator lights, and
REDIAL
again so the
then press
. The redialed num-
ber appears on the display.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 11 Tuesday, August 17, 1999 9:41 AM
For example, if you have call waiting,
press FLASH to take an incoming call
without disconnecting the current call.
FLASH appears. Press FLASH again
to return to the first call.
We recommend you not use RE-
DIAL to dial numbers that include a
tone (*) entry.
Note:
USING PAGE
Notes:
The PAGE feature allows someone at
the base to page you at the handset. It
also helps you find the handset if you
misplaced it.
• If you do not have special phone
services, pressing FLASH might
disconnect the current call.
• The redial memory does not store
a
FLASH entry or any digits
With the handset’s power on, the
handset beeps four sets of two beeps
when you press PAGE on the base.
The TALK key on the handset flashes,
and the channel number and INT ap-
pear on the display.
entered after you press FLASH.
USING TONE SERVICES
ON A PULSE LINE
Some special services, such as bank
by phone, require tone signals. If you
have pulse service, you can still use
these special tone services by follow-
ing these steps.
1. Set TONE/PULSE on the base to
PULSE.
2. Dial the service’s main number.
The handset will not beep during
Note:
a call.
3. When the service answers, press
* on the keypad. Aappears on the
display. Then dial the additional
numbers. The phone sends these
numbers as tone signals.
MEMORY DIALING
You can store up to 30 phone numbers
for quick and easy dialing. Each stored
number can be up to 16 digits long.
4. When you complete the call, place
the handset on the cradle or press
TALK to disconnect the call. The
phone automatically resets to the
pulse mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 12 Tuesday, August 17, 1999 9:41 AM
Notes:
2. Enter the phone number you want
to store. The number appears on
the display.
TONE/PULSE
PULSE
is set to
• If
and you want to use tone dialing
for a memory number, you must
store the tone entry along with the
number.
• To keep your accounts secure, we
recommend you do NOT store
your personal access code for
services such as bank-by-phone
in a memory location.
Notes:
Storing a Number in Memory
• The phone does not dial the
number at this point.
1. With the handset’s power on,
MEMORY
. The keypad lights
press
• If you enter a wrong digit, press
and MEMappears on the display.
FLASH/DEL
to delete the last
entered digit.
• If you enter more than 16 digits,
the phone buzzes and the dis-
play turns off. To dial a number
with more than 16 digits, see
“Chain Dialing.”
MEMORY
3. Press
again.
Note: While you are storing a
number in memory, if you do not
press any button on the keypad
within about 9 seconds, the key-
pad light turns off and a buzz
4. Enter the two-digit memory loca-
01, 02 ..... 30
tion number (
) where
you want to store the number. The
index number appears, and a long
beep sounds. The phone number
is now stored in the memory.
MEMORY
sounds. You must press
again so the keypad lights before
you can store the telephone num-
ber.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 13 Tuesday, August 17, 1999 9:41 AM
5. Pull out the memory index card at
the bottom of the base. Write the
person’s or company’s name and
index number on the sheet in pen-
cil (in case you want to change it
later).
Note: If a buzz sounds, you did not
successfully clear the memory loca-
tion. Try the process again.
Entering a Pause
in a Memory Number
In some telephone systems, you must
dial an access code (9, for example)
and wait for a second dial tone before
you can dial an outside number. If your
phone is connected to one of these
systems, you might want to enter a
pause at the appropriate point when
you store a phone number in memory.
6. Repeat Steps 2-5 to store other
telephone numbers.
At the appropriate place in the number,
PAUSE
press
to enter a 2-second
Notes:
pause. Pappears. For a longer pause,
• If you receive a call while you are
storing a number in memory,
PAUSE
press
again.
TALK
press
to answer the call.
PAUSE
it of memory.
Note: Each
entry uses one dig-
After the call, begin again at Step
1 to store the number.
• To change a phone number stored
in memory, simply store a new
phone number in that location.
Dialing a Stored Number
There are two ways to dial a stored
number.
• To clear a memory location so no
number is stored there, press
Method 1
MEMORY
twice, then press the
1. Lift the handset from the cradle
location number. A long beep
sounds. The phone number is
now cleared from the memory.
TALK
and press
so the keypad
key light.
TALK
and
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 14 Tuesday, August 17, 1999 9:41 AM
2. When you hear a dial tone, press
MEMORY, then press the number
buttons for the correct memory
location. The stored number
appears on the display, and the
phone dials the stored number.
or bank-by-phone), store the service’s
main phone number in one memory lo-
cation and numbers for additional in-
formation in other memory locations.
To chain dial memory numbers, follow
these steps.
1. With the handset’s power on,
press MEMORY and the memory-
location number for the service’s
main number. The numbers
appear.
2. Wait for the service to answer.
If you use pulse dialing to
Note:
dial the service, be sure you have
stored a * (tone) entry in the next
memory location used to send the
additional information.
Method 2
1. Lift the handset from the cradle
and press TALK so the keypad
and TALK key light.
3. Press MEMORY and the numbers
for the memory location where the
additional information is stored.
The numbers appear.
2. Press SCROLL s/t to search for
the desired stored number. The
selected number appears on the
display.
4. To disconnect the call, press TALK
so the TALK key does not light.
Testing Stored
Emergency Numbers
If you store an emergency service’s
number (police department, fire de-
partment, ambulance) and you want to
test the stored number, make the test
call during the late evening or early
morning to avoid peak demand peri-
ods. Remain on the line to explain the
reason for your call.
3. Press ENTER. The phone dials the
stored number.
Chain Dialing
When storing numbers for special ser-
vices (such as alternate long distance
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 15 Tuesday, August 17, 1999 9:41 AM
TROUBLESHOOTING
We do not expect you to have any
problems with your telephone, but if
you do, the following suggestions
might help. If you still have problems,
check other phones on the same line
to see if they work properly. If they do
and the problem does not seem to be
with your phone service, take your
phone to your local Radio Shack store
for assistance.
• Keep the handset away from inter-
ference sources such as comput-
ers, remote control toys, wireless
microphones, wireless alarm sys-
tems, wireless intercoms and
room monitors, fluorescent lights,
and electrical appliances. If the
interference is severe, turn off the
interfering device.
• Press CH to switch to another
channel.
Problem: The handset does not work.
Solutions:
Problem: The handset’s range de-
creases.
• Be sure POWER is set to ON.
• Move handset closer to the base.
Solutions:
• Fully extend the base’s antenna
vertically.
• Be sure the phone line cord and
AC adapter are correctly and
securely connected.
• Return the handset to the cradle,
and recharge the battery.
• Be sure the battery is charged.
• Be sure the antenna is not touch-
ing a metal surface.
• Fully extend the base’s antenna
vertically.
• Return the handset to the cradle
for 10 seconds, then try again.
Problem: Receiver sound flutters or
fades.
Solutions:
Problem: Volume drops or you hear
unusual sounds.
• Be sure the battery is charged.
Solution: Someone has picked up an-
other phone on the same line. Hang up
the other phone.
• Fully extend the base’s antenna
vertically.
• Move handset closer to the base.
Problem: Call is noisy.
Solutions:
• Do not place the base near appli-
ances or large metal objects.
• Hang up and redial the number.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 16 Tuesday, August 17, 1999 9:41 AM
Problem: Can make calls, but tele-
phone does not ring.
Solution:
• Telephone company may be using
unusual ringing methods. Your
telephone is designed for stan-
dard straight line bridged ringing.
POWER
ON
.
• Be sure
is set to
Problem: Can receive calls, but can-
not make calls.
Solution:
TONE/PULSE
• Set
correctly for the
type of service you have (see
“Setting the Dialing Mode”).
• Check with the phone company to
see if service is out in your area.
Problem: You cannot answer/make a
call and the handset sounds an error
tone when you lift it from the base or
TALK
press
.
Solution: The phone might be receiv-
ing interference from another RF sig-
nal; or, if the handset is away from the
base during a long period of AC power
failure, the phone might loss its access
protection code. Return the handset to
the base for 5 seconds.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 17 Tuesday, August 17, 1999 9:41 AM
CARE AND MAINTENANCE
Your ET-532 10-Channel Cordless Telephone with LCD Display is an example of
superior design and craftsmanship. The following suggestions will help you care for
your phones so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids can
contain minerals that corrode the electronic circuits.
Handle the phone gently and carefully. Dropping it can damage cir-
cuit boards and cases and cause the phone to work improperly.
Use and store the phone only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices and
distort or melt plastic parts.
Keep the phone away from dust and dirt which can cause premature
wear of parts.
Wipe the phone with a damp cloth occasionally to keep it looking
CLEANER
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean your phone.
Modifying or tampering with the phone’s internal components can cause a malfunc-
tion and might invalidate its warranty and void your FCC authorization to operate it.
If your phone is not performing as it should, take it to your local Radio Shack store
for assistance. If the trouble is affecting the phone lines, the phone company might
ask you to disconnect your phone until you have resolved the problem.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 18 Tuesday, August 17, 1999 9:41 AM
Important: Your telephone contains a
rechargeable nickel cadmium battery.
At the end of the battery’s useful life, it
must be recycled or disposed of prop-
erly. Contact your local, county, or
state hazardous waste management
authorities for information on recycling
or disposal programs in your area.
Some options that might be available
are: municipal curb-side collection,
drop off boxes at retailers, recycling
collection centers, and mail back pro-
grams.
REPLACING THE
BATTERY
If you follow the instructions in “Charg-
ing the Battery,” the supplied battery
should last for about a year. When the
battery loses its ability to fully charge,
order a 3.6 volt, 300 milliamp battery
with a connector that fits the connector
in the battery compartment. You can
order a replacement battery through
your local Radio Shack store.
Install the new battery as described
below, then charge the battery (see
“Charging the Battery”).
THE FCC WANTS YOU
TO KNOW
1. Slide off the battery compartment
cover and loosen the plastic strap
securing the battery. Then remove
the old battery.
In the unlikely event that your phone
causes problems on the phone line,
the phone company can temporarily
discontinue your service. If this hap-
pens, the phone company attempts to
notify you in advance. If advance no-
tice is not practical, the phone compa-
ny notifies you as soon as possible and
advises you of your right to file a com-
plaint with the FCC.
2. Insert the new battery in the com-
partment and secure it with the
plastic strap. Then connect the
battery’s plug to the pins inside
the compartment.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect
the operation of the phone. The phone
company notifies you of these changes
in advance, so you can take the neces-
sary steps to prevent interruption of
your phone service.
3. Replace the battery compartment
cover.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 19 Tuesday, August 17, 1999 9:41 AM
Your phone might cause TV or radio
interference even when it is operating
properly.
LIGHTNING
Your phone has built-in protection cir-
cuits to reduce the risk of damage from
surges in phone line current. These
protection circuits meet or exceed FCC
requirements. However, lightning strik-
ing the phone lines can damage your
phone.
To determine whether your phone is
causing the interference, turn off your
phone. If the interference goes away,
your phone is causing the interference.
Try to eliminate the interference by:
• Moving your phone away from the
receiver
Lighting damage is not common. Nev-
ertheless, if you live an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of
damage.
• Connecting your phone to an AC
outlet that is on a different electri-
cal circuit from the receiver
• Contacting your local Radio
Shack store for help
If you cannot eliminate the interfer-
ence, the FCC requires that you stop
using your phone.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1032.fm Page 20 Tuesday, August 17, 1999 9:41 AM
RADIO SHACK LIMITED WARRANTY
This telephone product is warranted against manufacturing defects in material and
workmanship for one (1) year from the date of purchase from Radio Shack company
owned stores and authorized Radio Shack franchisees and dealers. Within this period
bring your Radio Shack sales slip as proof-of-purchase date to any Radio Shack
store.
This warranty does not cover damage or failure caused by or attributable to Acts of
God, abuse, misuse, improper or abnormal usage, faulty installation, improper mainte-
nance, lightning or other incidence of excess voltage, or any repairs other than those
provided by a Radio Shack Authorized Service Facility, or transportation costs. Radio
Shack is not responsible or liable for indirect, special, or consequential damages
arising out of or in connection with the use or performance of the product or
other damages with respect to loss of property, loss of revenue or profit, or costs
of removal, installation or reinstallation.
EXCEPT AS PROVIDED HEREIN, RADIO SHACK MAKES NO EXPRESS WARRAN-
TIES AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURA-
TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states
do not allow the limitation or exclusion of incidental or consequential damages and
some states do not allow limitation or exclusion of implied warranties; therefore, the
aforesaid limitation(s) or exclusion(s) may not apply to the purchaser. There will be
charges rendered for repairs to the product made after the expiration of the aforesaid
one (1) year warranty period.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
We Service What We Sell
9/94
RADIO SHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102
7A5
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|