INSTRUCTION MANUAL
VSE-6300 SERIES
6-inch Fixed In-Ceiling Dome Housings
About this manual
Before installing and using this unit, please read
this manual carefully. Be sure to keep it available for
later reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
SICHERHEITSVORKEHRUNGEN: Aus Platzgründen kann
diese Warnung auf der Unterseite des Gerätes angebracht sein.
PRECAUCIONES DE SEGURIDAD: Debido a limitaciones de
espacio, esta etiqueta puede aparecer en la parte inferior de la unidad.
PRECAUCION: PARA REDUCIR EL RIESGO DE CHOQUE
ELÉCTRICO, FAVOR NO ABRIR LA CUBIERTA. ESTE EQUIPO NO
CONSTA DE PIEZAS O PARTES QUE REQUIEREN SERVICIO O
MANTENIMIENTO. PARA REPARACIONES FAVOR REFERIRSE A
UN TÉCNICO CALIFICADO.
VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU VERMEI-
DEN, ABDECKUNG NICHT ENTFERNEN. WARTUNGEN ALLER
ART QUALIFIZIERTEM PERSONAL ÜBERLASSEN.
Das Blitzsymbol im gleichseitigen Dreieck soll den Benutzer auf
nicht isolierte "Hochspannung" im Gehäuse aufmerksam machen,
die eventuell stark genug ist, um einen elektrischen Schlag zu
verursachen.
El símbolo representado por un relámpago con punta de flecha den-
tro de un triángulo equilátero, se muestra con el objetivo de alertar
al usuario que existen "voltages peligrosos" sin aislamiento, dentro
de la cubierta de la unidad. Dichos voltages pueden ser de tal mag-
nitud que constituyen un riesgo de choque eléctrico a personas.
Das Ausrufezeichen im gleichseitigen Dreieck soll den Benutzer
auf wichtige Bedienungs- und Wartungsanleitungen in der dem
Gerät beigefügten Literatur aufmerksam machen.
El símbolo de exclamación dentro de un triángulo equilátero, se
muestra con el objetivo de alertar al ususario de que instrucciones
de operación y mantenimiento importantes acompañan al equipo.
CONTENTS
1
2
3
4
5
6
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
DIMENSIONAL OUTLINE . . . . . . . . . . . . . . . . . . . .6
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1
UNPACKING
3
DESCRIPTION:
Unpack carefully.This equipment should be handled with care.
6-Inch Fixed Dome Housings
Check to ensure that the following items are included for the
applicable modules ordered:
MODEL NUMBER: VSE-6300 Series
•
•
•
VSE-6300 Series 6-Inch Fixed Dome Housing.
Hardware Kit.
Template Tool.
HIGHLIGHTS:
• For 1/4-inch, 1/3-inch, and 1/2-inch CCD Cameras
• For Fixed Camera In-ceiling Installations
• Plenum Ceiling Applications
• 360º AdjustableViewing Direction
• Concealed Camera Position
If an item appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper. If any items are
missing, contact Sanyo.
The shipping carton is the safest container in which the unit
may be transported. Save it for possible future use.
• Quick Latch Mount for Sheet Rock and Drop Ceilings
• Durable Aluminum Back Box with Conduit Access
• Domed and Flat WindowVersions
• Optional Integrated Camera/Lens Combinations (OnePak™)
• Attractive/Discreet Design
2
SERVICE
If the unit ever needs repair service or parts, the customer
should contact Sanyo Technical Support 1-(888)-66SANYO.
• Perfect for Casino, Business, and Retail Applications
• Dust Resistant
• Easy Installation
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL SPECIFICATIONS
4. Install box into pre-cut tile with the bottom flange, then
press against the tile. Position the round section of the
box in the direction that the camera will be aimed. See
Figure 1.
Model Number
Window Type
Trim Ring Color
Dome, Smoked
Dome, Smoked
Flat, Smoked
Black
VSE-6300DSB
VSE-6300DSW
VSE-6300FSB
VSE-6300FSW
White
Black
Flat, Smoked
White
Model Number
Maximum Camera and Lens
Weight
7.5 L x 3.0 W x 3.0 H in
(190 x 76 x 76 mm)
~2 lbs. (0.9 kg)
~2 lbs. (0.9 kg)
~2 lbs. (0.9 kg)
~2 lbs. (0.9 kg)
VSE-6300DSB
VSE-6300DSW
VSE-6300FSB
VSE-6300FSW
7.5 L x 3.0 W x 3.0 H in
(190 x 76 x 76 mm)
5.2L x 3.0W x 3.0H in
(132 x 76 x 76mm)
5.2L x 3.0W x 3.0H in
(132 x 76 x 76mm)
Figure 1
5. Pull the drawstring tight (away from the screw) and lock
into groove. DO NOT CUT DRAWSTRING Push the
excess string through the hole provided. As an option, a
screwdriver may be used to turn screws and lock ceiling
clamps in place.
Note: A right angle BNC is recommended
Camera Mounting:
A two-arm camera support bracket, adjustable forward and
backward, is included with each unit.
6. Reinstall tile in grid.
Window: Lightly tinted acrylic.
7. Fasten support wire (not provided) to structural framing,
masonry, or concrete above the unit. Connect the other
end to the eyebolt in the top of the box. Draw wire tight
and twist securely.
Construction: Housing is constructed of aluminum. The
lower domed window has a silk-screened window with a
lightly tinted viewing area. The lower flat window is lightly
tinted with no silk screened areas.
8. Run the electrical cable into the housing through the con-
duit as required by applicable codes.
4
INSTALLATION
Attention: Installation should be performed by quali-
fied service personnel only, in accordance with the
National Electrical Code or applicable local codes.
Refer to applicable installation section.
9. Complete the electrical connections.
10. Adjust camera bracket to proper angle and mount camera
to camera bracket. See Figure 2.
4.1 Suspended Ceiling Mounting
CAUTION:These units must be properly and
securely mounted to a supporting structure capable
of sustaining the unit weight. Use care when selecting
mounting hardware (not supplied) for installation
The mounting surface and unit's weight should be
carefully considered.
Mount the unit in a suspended ceiling grid using the existing
ceiling tile as follows:
1. Remove tile at desired location
2. Move adjacent tiles for access as required.
Figure 2
3. Cut a 172 mm (6.75 in) diameter hole in the center of the
tile. Use two pencils (or a pencil and a nail) with the tem-
plate tool provided to draw the circle.
11. Assemble dome in the trim ring by lining the slots in the
dome with tabs in the trim ring. Push one side of the
dome under the tab; the other side should clear the other
tab. Turn the dome to secure it.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Attach the dome/trim ring by lining up the dots on the
box and the trim ring. Push on one side of the trim ring
near the the flat section of the box, then push on the
other side of the trim ring until it snaps into place. Listen
for a distinct click to ensure ring is securely in place. See
Figure 3.
4. Pull the drawstring tight (away from the screw) and lock
into the groove. DO NOT CUT DRAWSTRING
Push the excess string through the hole provided. As an
option, a screwdriver may be used to turn screws and
lock ceiling clamps in place.
5. Complete the electrical connections.
6. Adjust camera bracket to proper angle and mount cam-
era to camera bracket. See Figure 5.
Figure 3
13. Adjust the dome so that the viewing slot is in the proper
position.
14. Replace any previously removed adjacent tiles.
Figure 5
4.2 Hard Ceiling Mounting
Mount the unit in a hard ceiling, e.g. dry wall etc. as follows.
Be sure the ceiling will support the weight of the housing and
camera.
7. Assemble dome in the trim ring by lining the slots in the
dome with tabs in the trim ring. Push one side of the
dome under the tab; the other side should clear the other
tab. Now turn the dome to secure it.
1. Cut a 172 mm (6.75 in) diameter hole in the ceiling. Use
two pencils (or a pencil and a nail) with the template tool
provided to draw the circle.
8. Attach the dome/trim ring by lining up the dots on the
box and the trim ring. Push on one side of the trim ring
near the the flat section of the box, then push on the
other side of the trim ring until it snaps into place. Listen
for a distinct click to ensure ring is securely in place. See
Figure 6.
2. Run the electrical cable into the housing through the con-
duit and the hole in ceiling as required by the applicable
codes.
3. Install box into pre-cut hole with the bottom flange press-
ing against the ceiling. Position the round section of the
box in the direction that the camera will be aimed. See
Figure 4.
Figure 6
9. Adjust the dome so that the viewing slot is in the proper
position
Figure 4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5
MAINTENANCE
No special maintenance is required.
If internal wiping is necessary, use only microwave type paper
towels, or equivalent soft paper towels. Roll a section into a
tightly wound tube, tear tube in half, and wet the fuzzy torn
end with a solution of isopropyl alcohol diluted with water.
While holding the dome with its opening facing down, wipe
the interior using a circular motion spiraling in toward the
center. Use a new paper towel for each two passes.
To clean the exterior of the dome, use any nonabrasive clean-
ing cloth and cleaning agent that is safe for use on acrylic
plastic. Liquid or spray cleaner/wax suitable for use on fine
furniture is acceptable.
6
DIMENSIONAL OUTLINE
mm
inches
Figure 8
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SANYO INDUSTRIALVIDEO
HOUSINGS OR INTEGRATED CAMERA/LENS/HOUSING PACKAGES
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s
expense, unless specifically stated otherwise in this warranty.The names and addresses of Authorized Sanyo Service Centers may be obtained
by calling the toll-free number listed below.
For product operation, authorized service center referral, service assistance or problem resolution, call
CUSTOMER INFORMATION 1- 800- 421- 5013
Weekdays 8: 30 AM – 5: 00 PM PacificTime
For accessories and/ or parts, call
PARTS ORDER INFORMATION 1- 800- 726- 9662
Weekdays 8: 30 AM – 5: 00 PM PacificTime
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA,
EXCLUDING ALL U. S.TERRITORIES AND PROTECTORATES.THISWARRANTY APPLIES ONLYTOTHE ORIGINAL RETAIL PURCHASER
OR END USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE
AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in
materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product or any of its parts which fail
to conform to this warranty.The warranty period commences on the date the product was first purchased or rented at retail.
LABOR
PARTS
3YEARS
3YEARS
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer- operated controls as explained in the appropriate model’s instruction manual,
or (B) the repair of any product whose serial number has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any
malfunction,defect or failure caused by or resulting from unauthorized service or parts,improper maintenance,operation contrary to furnished
instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,
flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other express warranties and SFC does not assume or authorize any party to assume for it any other obligation
or liability.
SFC DISCLAIMS ALL OTHERWARRANTIES EXPRESS OR IMPLIED,WITH REGARDTOTHIS PRODUCT (INCLUDINGTHEWARRANTIES
OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS
OBLIGATIONS UNDERTHISWARRANTY DUETO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND
DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER,ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR OWN-
ERSHIP OFTHIS PRODUCT INCLUDINGWARRANTOR’S NEGLIGENCE,ORALLEGED DAMAGED OR DEFECTIIVE GOODS,WHETHER
SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
ATTENTION
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.
Model No _____________________________________________ Serial No. __________________________________________
(Located on back or bottom side of unit.)
Date of Purchase ______________________________________ Purchase Price ______________________________________
Where Purchased ___________________________________________________________________________________________
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Sanyo Fisher Company
SecurityVideo Division
21605 Plummer Street
Chatsworth, CA 91311
Tel: (818) 998-7322
Fax: (818) 717-2716
Technical Support: (888) 66SANYO
100 0008 001 SAN 6/02
Printed in USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|