Poulan Snow Blower 428558 User Manual

IMPORTANT MANUAL  
Do Not Throw Away  
OWNER'S MANUAL  
MODEL NUMBER:  
WARNING:  
Read the Owner's Manual and  
follow all Warnings and Safety  
Instructions. Failure to do so  
can result in serious injury.  
961940009  
SNOW THROWER  
Always Wear Eye Protection During Operation  
428558 Rev.3 08.31.09 SR  
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Whencleaning,repairingorinspectingthesnowthrower,  
stop the engine and make certain the collector/impel-  
ler and all moving parts have stopped. Disconnect  
the spark plug wire and keep the wire away from the  
plug to prevent someone from accidentally starting the  
engine.  
7. Do not run the engine indoors, except when starting  
the engine and for transporting the snow thrower in or  
out of the building. Open the outside doors; exhaust  
fumes are dangerous.  
Clearing a Clogged Discharge Chute  
Handcontactwiththerotatingimpellerinsidethedischarge  
chute is the most common cause of injury associated with  
snow throwers. Never use your hand to clean out the dis-  
charge chute. To clear the chute:  
1. SHUT THE ENGINE OFF!  
2. Wait 10 seconds to be sure the impeller blades have  
stopped rotating.  
3. Always use a clean-out tool, not your hands.  
8. Exercise extreme caution when operating on slopes.  
Maintenance and Storage  
1. Check shear bolts and other bolts at frequent intervals  
for proper tightness to be sure the equipment is in safe  
working condition.  
2. Never store the machine with fuel in the fuel tank  
inside a building where ignition sources are present  
such as hot water heaters, space heaters, or clothes  
dryers. Allow the engine to cool before storing in any  
enclosure.  
3. Always refer to operator’s manual for important details  
if the snow thrower is to be stored for an extended  
period.  
9. Neveroperatethesnowthrowerwithoutproperguards,  
and other safety protective devices in place and work-  
ing.  
10. Never direct the discharge toward people or areas  
where property damage can occur. Keep children and  
others away.  
11. Do not overload the machine capacity by attempting  
to clear snow at too fast a rate.  
12. Never operate the machine at high transport speeds  
on slippery surfaces. Look behind and use care when  
operating in reverse.  
13. Disengage power to the collector/impeller when snow  
thrower is transported or not in use.  
14. Use only attachments and accessories approved by  
the manufacturer of the snow thrower (such as wheel  
weights, counterweights, or cabs).  
4. Maintain or replace safety and instruction labels, as  
necessary.  
5. Run the machine a few minutes after throwing snow  
to prevent freeze-up of the collector/impeller.  
15. Never operate the snow thrower without good visibility  
or light. Always be sure of your footing, and keep a firm  
hold on the handles. Walk; never run.  
16. Never touch a hot engine or muffler.  
CONGRATULATIONS on your purchase of a new snow  
thrower. It has been designed, engineered and manu-  
factured to give best possible dependability and perfor-  
mance.  
PRODUCT SPECIFICATIONS  
Gasoline Capacity 0.5 Gallons (1,9 Liters)  
and Type:  
Unleaded Regular only  
Should you experience any problem you cannot easily  
remedy, please contact your nearest authorized service  
center. We have competent, well-trained technicians and  
the proper tools to service or repair this unit.  
Oil Type  
(API SG–SL):  
SAE 30 (above 50°F)  
SAE 5W-30 or 10W-30 (32° to 50°F)  
SAE 5W-30 (below 32°F)  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your snow thrower  
properly. Always observe the “SAFETY RULES”.  
Oil Capacity:  
20 Ounces (0,57 Liters)  
Spark Plug:  
Gap:  
Champion RN9YC  
0.030" (0,762 mm)  
SERIAL NUMBER: ___________________________  
DATE OF PURCHASE: _______________________  
CUSTOMER RESPONSIBILITIES  
THEMODELANDSERIALNUMBERSWILLBEFOUND  
ONADECALATTACHEDTOTHEREAROFTHESNOW  
THROWER HOUSING.  
Read and observe the safety rules.  
Follow a regular schedule in maintaining, caring for  
and using your snow thrower.  
YOUSHOULDRECORDBOTHSERIALNUMBERAND  
DATE OF PURCHASE AND KEEP IN A SAFE PLACE  
FOR FUTURE REFERENCE.  
Follow the instructions under “Maintenance” and “Stor-  
age” sections of this owner’s manual.  
TABLE OF CONTENTS  
SAFETY RULES ........................................................ 2-3  
MAINTENANCE..................................................... 14-15  
SERVICE AND ADJUSTMENTS........................... 16-18  
STORAGE................................................................... 19  
TROUBLESHOOTING................................................ 20  
REPAIR PARTS ..................................................... 22-39  
WARRANTY...............................................BACK PAGE  
PRODUCT SPECIFICATIONS...................................... 3  
CUSTOMER RESPONSIBILITIES................................ 3  
ASSEMBLY / PRE-OPERATION ............................... 5-7  
OPERATION ............................................................ 8-13  
MAINTENANCE SCHEDULE ..................................... 14  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS PACKED SEPARATELY IN CARTON  
(1) POWER CORD  
(1) MULTI-  
(198563)  
WRENCH  
(180684)  
(3) RETAINER  
SPRINGS  
(169675)  
(2) LOCKNUTS  
(2) SHEAR BOLTS 1/4-20 x 1-3/4  
1/4-20  
(192090)  
(2) FLAT WASHERS  
(73800400)  
(2) CARRIAGE BOLTS  
3/8-16 x 2.25  
SAFTEY  
IGNITION KEY(S)  
(422663)  
(1) LOCKNUT 3/8  
(73800600)  
(1) WASHER 3/8  
(19131316)  
(2) HANDLE KNOBS  
(1) LOCKNUT (1) CARRIAGE BOLT  
(1) LOCKNUT  
1/4-20  
(1) SHOULDER  
BOLT 1/4-20  
(179829)  
(1) SPRING  
(184505)  
5/16-18  
5/16-18 x 5/8  
(72250505)  
(751153)  
(191730)  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
Read these instructions and this manual in its entirety before you attempt to assemble or operate your new  
snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly,  
operation and maintenance of the product.  
Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping  
purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts  
bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened  
securely. Use the correct tools as necessary to ensure proper tightness.  
REMOVE SNOW THROWER FROM CARTON  
SPEED  
1. Remove all accessible loose parts and parts boxes  
CONTROL  
from carton.  
ROD  
2. Cut down all four corners of carton and lay panels flat.  
PLASTIC TIE  
3. Removethetwo(2)screwssecuringtheaugerhousing  
to the pallet.  
UPPER  
HANDLE  
4. Removeallpackingmaterialsexceptplastictieholding  
speed control rod to lower handle.  
5. Remove the two (2) plastic ties securing the upper  
handle to the pallet.  
6. Remove snow thrower from carton and check carton  
thoroughly for additional loose parts.  
HANDLE  
KNOB  
LOWER  
HANDLE  
HOW TO SET UP YOUR SNOW THROWER  
TOOL BOX (See Fig. 10)  
A toolbox is provided on your snow thrower. The toolbox is  
located on top of the belt cover. Store the extra shear bolts,  
nuts and multi-wrench provided in parts bag in the toolbox.  
NOTE: The multi-wrench may be used for assembly of the  
chuterotatorheadtosnowthrowerandmakingadjustments  
to the skid plates.  
UNFOLD UPPER HANDLE  
1. Raise upper handle to the operating position and  
tighten handle knobs securely. Additional carriage  
bolts, washers and handle knobs are in bag of parts.  
Use to secure upper handle to lower handle. Install  
in lower holes in handles.  
FIG. 1  
SPEED CONTROL ROD  
RETAINER  
SPRING  
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)  
1. Remove plastic tie securing rod to lower handle.  
2. Insert rod into speed control bracket and secure with  
retainer spring.  
SPEED  
CONTROL  
BRACKET  
SPEED  
CONTROL  
LEVER  
FIG. 2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
INSTALL TRACTION DRIVE CONTROL ROD  
(See Figs. 3 and 4)  
The traction drive control rod is installed on the snow  
thrower.  
1. Remove plastic tie securing rod to lower handle.  
2. With top end of rod positioned under left side of control  
panel, pushroddownandinserttopendofrodintohole  
in drive control bracket. Secure with retainer spring.  
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)  
1. Retrieve vinyl sleeve and spring from bag of parts and  
retrieve the auger control rod from carton chute tray.  
Slide straight rod end through the small hole in the  
vinyl sleeve. Hook spring in hole in rod end.  
2. Hook end of spring into control arm with loop opening  
up as shown. (See Fig. 5)  
3. With top end of rod positioned under right side of  
control panel, push down on rod and insert end of rod  
intoholeinaugercontrolbracket. Securewithretainer  
spring.  
PLASTIC TIE  
TRACTION DRIVE  
CONTROL ROD  
AUGER  
CONTROL  
ROD  
VINYL  
SLEEVE  
VINYL  
SLEEVE  
CONTROL  
ARM  
LOOP  
OPENING  
UP  
FIG. 3  
FIG. 5  
TRACTION DRIVE  
CONTROL LEVER  
RETAINER  
SPRING  
AUGER CONTROL ROD  
AUGER  
CONTROL  
LEVER  
RETAINER  
SPRING  
TRACTION  
DRIVE  
CONTROL  
ROD  
DRIVE  
CONTROL  
BRACKET  
AUGER  
CONTROL  
BRACKET  
FIG. 4  
FIG. 6  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
INSTALL DISCHARGE CHUTE / CHUTE ROTATER  
HEAD (See Fig. 7)  
INSTALL CHUTE DEFLECTOR REMOTE CONTROL  
(See Figs. 8 and 9)  
1. Install remote cable bracket to discharge chute with  
5/16-18 carriage bolt and 5/16-18 locknut as shown.  
Tighten securely.  
2. Install remote cable eyelet to chute deflector with  
1/4-20 shoulder bolt and 1/4-20 locknut as shown.  
Tighten nut securely. Eyelet will be loose on shoulder  
bolt.  
NOTE: The multi-wrench provided in your parts bag may  
be used to install the chute rotater head.  
1. Place discharge chute assembly on top of chute base  
with discharge opening toward front of snow thrower.  
2. Positionchuterotaterheadoverchutebracket. Ifneces-  
sary,rotatechuteassemblytoalignsquareandpinonun-  
dersideofchuterotaterheadwithholesinchutebracket.  
3. With chute rotater head and chute bracket aligned,  
position chute rotater head on pin and threaded stud  
of mounting bracket.  
4. Install 3/8 washer and locknut on threaded stud and  
tighten securely.  
3. Install spring hooks between hex nuts on chute rotater  
head and into hole in chute deflector as shown.  
SPRING  
1/4-20  
CHUTE  
SHOULDER  
DEFLECTOR  
BOLT  
HOOK  
BETWEEN  
HEX NUTS  
ON CHUTE  
ROTATER  
HEAD  
CHUTE  
ROTATER  
HEAD  
3/8 LOCKNUT  
3/8 WASHER  
1/4-20  
LOCKNUT  
5/16-18  
CARRIAGE  
BOLT  
CABLE  
EYELET  
REMOTE  
CABLE  
BRACKET  
PIN  
THREADED  
STUD  
5/16-18  
LOCKNUT  
FIG. 8  
ROTATER HEAD  
MOUNTING  
ALIGN BEFORE  
TIGHTENING LOCKNUT  
CHUTE  
BRACKET  
BRACKET  
FIG. 7  
CHUTE DEFLECTOR  
CONTROL LEVER  
FIG. 9  
CHECK TIRE PRESSURE  
Thetiresonyoursnowthrowerwereoverinflatedatthefac-  
tory for shipping purposes. Correct and equal tire pressure  
is important for best snow throwing performance.  
Reduce tire pressure to 14-17 PSI.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR SNOW THROWER  
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare  
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save  
this manual for future reference.  
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand  
their meaning.  
PRIMER  
DANGER  
OR WARNING  
READ AND FOLLOW ALL SAFETY INFORMATION  
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.  
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
FORWARD REVERSE  
IGNITION KEY.  
INSERT TO START  
AND RUN,  
PULL OUT TO STOP.  
DISENGAGED  
ENGAGED  
SNOW  
TRACTION  
DISCHARGE  
DRIVE CONTROL  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
MUFFLER  
ELECTRIC  
START  
AUGER  
DISCHARGE CHUTE CONTROL LEVER  
CONTROL  
LEVER  
BUTTON  
DEFLECTOR  
REMOTE  
CONTROL  
LEVER  
TRACTION  
DRIVE  
CONTROL  
LEVER  
DRIVE SPEED  
CONTROL LEVER  
GASOLINE  
FILLER CAP  
POWER  
CORD  
PLUG  
CHUTE  
DEFLECTOR  
CHOKE  
CON-  
TROL  
SAFETY  
IGNITION  
KEY  
LH TURN  
TRIGGER  
ON / OFF  
SWITCH  
DISCHARGE  
CHUTE  
PRIMER  
FUEL SHUT-OFF VALVE  
LIGHT  
RECOIL (AUXILIARY) STARTER HANDLE  
HANDLE  
KNOB  
CLEAN-OUT TOOL  
MUFFLER  
TOOLBOX  
NOTE: ITEMS ABOVE  
ARE SHOWN IN  
THEIR TYPICAL  
LOCATION ON THE  
ENGINE. ACTUAL  
LOCATION MAY VARY  
WITH THE ENGINE  
ON YOUR UNIT.  
SKID PLATE  
AUGERS  
FIG. 10  
MEETS A.N.S.I. SAFETY REQUIREMENTS  
Our snow throwers conform to the standards of the American National Standards Institute.  
Toolbox - used to store spare shear bolts, locknuts and  
wrench.  
Drive speed control lever - used to select forward or  
reverse motion and speed of snow thrower.  
Safety ignition key - must be inserted for the engine to  
start and run. Remove when snow thrower is not in use.  
Traction drive control lever - used to engage power-pro-  
pelled forward or reverse motion of snow thrower.  
Electric start button - used for starting the engine.  
Auger control lever - used to engage auger motion (throw  
snow).  
Recoil(auxiliary)starterhandle-usedforstartingengine.  
Discharge chute control lever - used to change the di-  
rection the snow is thrown.  
Primer - pumps additional fuel from the carburetor to the  
cylinder for use when starting a cold engine.  
Deflector remote control lever - used to change the  
distance the snow is thrown.  
Choke Control - used for starting a cold engine.  
ON / OFF switch - used to STOP the engine.  
Skid plate - used to adjust height of scraper bar from the  
ground.  
LH and RH turn triggers - used to steer the snow thrower.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO CONTROL SNOW DISCHARGE (See Fig. 13)  
The operation of any snow thrower can result  
in foreign objects thrown into the eyes, which  
canresultinsevereeyedamage. Alwayswear  
WARNING: Snow throwers have ex-  
posed rotating parts, which can cause  
severe injury from contact, or from ma-  
terial thrown from the discharge chute.  
Keep the area of operation clear of all  
persons, small children and pets at all  
times including startup.  
safety glasses or eye shields while operating  
your snow thrower or performing any adjust-  
ments or repairs. We recommend standard safety glasses  
or a wide vision safety mask worn over spectacles.  
HOW TO USE YOUR SNOW THROWER  
Know how to operate all controls before adding fuel or  
WARNING:Ifthedischargechuteorau-  
ger become clogged, shut-off engine  
andwaitforallmovingpartstostop.Use  
the clean-out tool, NOT YOUR HANDS,  
to unclog the chute and/or auger.  
attempting to start the engine.  
STOPPING  
TRACTION DRIVE  
Release traction drive control lever to stop the forward  
or reverse movement of the snow thrower.  
TheDIRECTIONinwhichsnowistobethrowniscontrolled  
by the discharge chute control lever.  
AUGER  
Tochangethedischargechuteposition,pressdownward  
on discharge chute control lever and move lever left  
or right until chute is in desired position. Be sure lever  
springs back and locks into desired position.  
Release the auger control lever to stop throwing snow.  
ENGINE  
1. Move ON / OFF switch to “OFF” position.  
2. Remove (do not turn) safety ignition key to prevent  
unauthorized use.  
The DISTANCE that snow is thrown is controlled by the  
position of the chute deflector. Set the deflector low to  
throw snow a short distance; set the deflector higher to  
throw snow farther.  
NOTE: Never use choke to stop engine.  
TO USE FUEL SHUT-OFF VALVE (See Fig. 11)  
Press downward on chute deflector control lever and  
moveleverforwardtolowerthedeflectoranddecrease  
the distance. Move lever back to raise the deflector  
and increase the distance. Be sure lever springs back  
and locks into desired position.  
The fuel shut-off valve is located beneath the fuel tank on  
the engine. Always operate the snow thrower with the fuel  
shut-off valve in the OPEN position.  
DISCHARGE CHUTE  
CONTROL LEVER  
OFF  
OPEN  
FIG. 11  
CHUTE DEFLECTOR  
REMOTE CONTROL LEVER  
TO USE CHOKE CONTROL (See Fig. 12)  
FIG. 13  
The choke control is located on the engine. Use the choke  
control whenever you are starting a cold engine. Do not  
use to start a warm engine.  
TO THROW SNOW (See Fig. 14)  
The auger rotation is controlled by the auger control lever  
located on the right side handle.  
To engage choke, rotate lever to “FULLposition.  
Squeeze auger control lever to handle to engage the  
auger and throw snow.  
Release the auger control lever to stop throwing snow.  
FULL  
OFF  
AUGER  
CONTROL  
LEVER  
FIG. 12  
FIG. 14  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO MOVE FORWARD AND BACKWARD (See Fig. 16)  
USING THE CLEAN-OUT TOOL (See Fig. 15)  
SELF-PROPELLING, forward and reverse movement of  
the snow thrower, is controlled by the traction drive control  
lever located on the left side handle.  
In certain snow conditions, the discharge chute may be-  
come clogged with ice and snow. Use the clean-out tool  
to dislodge this blockage.  
Squeezetractiondrivecontrollevertohandletoengage  
the drive system.  
Release traction drive control lever to stop the forward  
or reverse movement of the snow thrower.  
When cleaning, repairing, or inspecting, make  
certain all controls are disengaged and the au-  
ger/impellerandallmovingpartshavestopped.  
Disconnect the spark plug wire and keep the  
wire away from the spark plug to prevent ac-  
cidental starting.  
SPEED and DIRECTION are controlled by the drive speed  
control lever.  
Press downward on the speed control lever and move  
lever to desired position BEFORE engaging the trac-  
tion drive control lever. Be sure lever springs back and  
locks into desired position.  
Releasetheaugercontrolleverandshutofftheengine.  
Removetheclean-outtoolfromit'smountingclip. Grasp  
the tool firmly by the handle and push and twist the tool  
into the discharge chute to dislodge the blockage.  
CAUTION: Do not move speed control lever  
when traction drive control lever is engaged.  
Damage to the snow thrower can result.  
Afterthepackedsnowhasbeendislodged,returntheclean-  
out tool to it's mounting clip by pushing it into the clip.  
Makesurethedischargechuteispointedinasafedirec-  
tion(novehicles,buildings,people,orotherobjectsare  
in the direction of discharge) before restarting engine.  
Restart the engine, then squeeze the auger control  
lever to the handle to clear snow from the auger hous-  
ing and the discharge chute.  
Slower speeds are for heavier snow and faster speeds  
are for light snow and transporting the snow thrower. It  
is recommended that you use a slower speed until you  
are familiar with the operation of the snow thrower.  
NOTE: When both traction drive and auger control levers  
are engaged, the traction drive control lever will lock the  
auger control lever in the engaged position. This will allow  
you to release your right hand from the handle and adjust  
the discharge chute direction without interrupting the snow  
throwing process.  
DISCHARGE CHUTE  
TRACTION DRIVE  
CONTROL LEVER  
CLEAN-OUT  
TOOL  
MOUNTING  
CLIP  
DRIVE SPEED  
CONTROL LEVER  
FIG. 15  
FIG. 16  
POWER STEERING OPERATION (See Fig. 17)  
Steering triggers are used to assist in steering your snow  
thrower. The triggers are located on the underside of each  
handle. Whenatriggerissqueezed, itdisengagesthedrive  
wheel on that side of snow thrower and allows it to turn in  
that direction.  
To turn left – squeeze left side trigger.  
To turn right – squeeze right side trigger.  
LH TURN  
TRIGGER  
RH TURN  
TRIGGER  
FIG. 17  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
BEFORE STARTING THE ENGINE  
TO ADJUST SKID PLATES (See Fig. 18)  
NOTE: The wrench provided in your parts bag may be  
CHECK ENGINE OIL LEVEL (See Fig. 19)  
The engine on your snow thrower has been shipped, from  
the factory, already filled with oil.  
used to adjust the skid plates.  
Skid plates are located on each side of the auger housing  
and adjust the clearance between the scraper bar and the  
ground surface. Adjust skid plates evenly to proper height  
for current surface conditions. For removal of snow in  
normal conditions, such as a paved driveway or sidewalk,  
place skid plates in the highest position (lowest scraper  
clearance) to give a 1/8" clearance between the scraper  
bar and the ground. Use a middle position if the surface  
to be cleared is uneven.  
1. Check engine oil with snow thrower on level ground.  
2. Remove oil fill cap/dipstick and wipe clean, reinsert  
the dipstick and screw tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULLmark on dipstick is reached. Do not overfill.  
To change engine oil, see “TO CHANGE ENGINE OIL”  
in the Maintenance section of this manual.  
NOTE: It is not recommended to operate the snow thrower  
overgravelorrockysurfaces.Objectssuchasgravel,rocks  
or other debris, can easily be picked up and thrown by the  
impeller, which can cause serious personal injury, property  
damage or damage to the snow thrower.  
ADD GASOLINE (See Fig. 19)  
Fill fuel tank to bottom of tank filler neck. Do not over-  
fill. Use fresh, clean, regular unleaded gasoline with  
a minimum of 87 octane. Do not mix oil with gasoline.  
Purchase fuel in quantities that can be used within 30  
days to assure fuel freshness.  
If snow thrower must be operated over gravel surface,  
use extra caution and be sure skid plates are adjusted  
to lowest (highest scraper clearance) position.  
WARNING: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
1. Shut off engine and wait for all moving parts to stop.  
2. Adjust skid plates by loosening the 1/2" hex nuts, then  
moving skid plate to desired position. Be sure both  
plates are adjusted evenly. Tighten securely.  
CAUTION: Alcohol blended fuels (called gaso-  
hol or using ethanol or methanol) can attract  
moisture which leads to separation and forma-  
tion of acids during storage. Acidic gas can  
damage the fuel system of an engine while in  
storage. To avoid engine problems, the fuel  
system should be emptied before storage of  
30 days or longer. Drain the gas tank, start  
the engine and let it run until the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. SeeStorageInstructionsforadditional  
information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent  
damage may occur.  
HIGH POSITION  
(LOW GROUND  
CLEARANCE)  
AUGER  
HOUSING  
SCRAPER BAR  
HEX  
SKID PLATE  
NUTS  
LOW POSITION (HIGH GROUND CLEARANCE)  
FIG. 18  
RECOIL (AUXILIARY)  
STARTER HANDLE  
ON / OFF  
SWITCH  
SCRAPER BAR (See Fig. 18)  
The scraper bar is not adjustable, but is reversible. After  
considerable use it may become worn. When it has worn  
almost to the edge of the housing, it can be reversed,  
providing additional service before requiring replacement.  
Replace a damaged or worn scraper bar.  
GASOLINE  
FILLER CAP  
ENGINE OIL FILL  
CAP / DIPSTICK  
CHOKE  
CON-  
TROL  
STARTER  
BUTTON  
SAFETY  
IGNITION  
KEY  
PRIMER  
POWER  
CORD  
PLUG  
FUEL SHUT-OFF VALVE  
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.  
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.  
FIG. 19  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO START ENGINE  
Be sure fuel shut-off valve is in the “OPEN” position.  
6. Whentheenginestarts,releasetherecoilstarterhandle  
and slowly move the choke control to the “OFF” posi-  
tion.  
Your snow thrower engine is equipped with both a 120 Volt  
A.C. electric starter and a recoil starter. The electric starter  
is equipped with a three-wire power cord and plug and is  
designed to operate on 120 Volt A.C. household current.  
Allow the engine to warm up for a few minutes. Engine will  
not develop full power until it has reached normal operat-  
ing temperature.  
WARM START - RECOIL STARTER  
Be sure your house is a 120 Volt A.C. three-wire  
grounded system. If you are uncertain, consult a  
licensed electrician.  
Follow the steps above, keeping the choke in the “OFF”  
position. DO NOT push the primer.  
BEFORE STOPPING  
Run the engine for a few minutes to help dry off any mois-  
ture on the engine.  
WARNING: Do not use the electric  
starter if your house is not a 120 Volt  
A.C.three-wiregroundedsystem. Seri-  
ous personal injury or damage to your  
snow thrower could result.  
IF RECOIL STARTER HAS FROZEN  
If the recoil starter has frozen and will not turn the engine,  
proceed as follows:  
COLD START - ELECTRIC STARTER  
1. Grasp the recoil starter handle and slowly pull as much  
rope out of the starter as possible.  
2. Release the recoil starter handle and let it snap back  
against the starter.  
1. Insert safety ignition key (tied to recoil start cord) into  
ignition slot until it clicks. DO NOT turn the key. Keep  
the extra safety ignition key in a safe place.  
2. Place ON / OFF switch in “ON” position.  
3. Move choke control to “FULLposition.  
4. Connect the power cord to the engine.  
If the engine still fails to start, repeat the above steps or  
use the electric starter.  
5. Plug the other end of the power cord into a three-hole  
grounded 120 Volt A.C. receptacle.  
SNOW THROWING TIPS  
Go slower in deep, freezing or heavy wet snow. Use  
the drive speed control, NOT the ON / OFF switch, to  
adjust speed.  
NOTE: Do not use primer when starting engine with the  
electric starter.  
6. Push starter button until engine starts.  
It is easier and more efficient to remove snow imme-  
diately after it falls.  
The best time to remove snow is the early morning. At  
this time the snow is usually dry and has not been ex-  
posed to the direct sun and warming temperatures.  
Slightly overlap each successive path to ensure all  
snow will be removed.  
Throw snow downwind whenever possible.  
IMPORTANT: Do not crank engine more than five continu-  
ous seconds between each time you try to start. Wait 5 to  
10 seconds between each attempt.  
7. When the engine starts, release the starter button and  
slowly move the choke control to the “OFF” position.  
8. Disconnect the power cord from the receptacle first,  
then from the engine.  
Allow the engine to warm up for a few minutes. Engine will  
not develop full power until it has reached normal operat-  
ing temperature.  
Adjust the skid plates to proper height for current snow  
conditions. See “TO ADJUST SKID PLATES” in this  
section of this manual.  
For extremely heavy snow, reduce the width of snow  
removal by overlapping previous path and moving  
slowly.  
Keep engine clean and clear of snow during use. This  
will help air flow and extend engine life.  
Aftersnow-throwingiscompleted,allowenginetorunfor  
a few minutes to melt snow and ice off the engine.  
Clean the entire snow thrower thoroughly after each  
use and wipe dry so it is ready for next use.  
WARM START - ELECTRIC STARTER  
Follow the steps above, keeping the choke control in the  
“OFF” position.  
COLD START - RECOIL STARTER  
1. Insert safety ignition key (tied to recoil start cord) into  
ignition slot until it clicks. DO NOT turn the key. Keep  
the extra safety ignition key in a safe place.  
2. Place ON / OFF switch in “ON” position.  
3. Rotate choke control to “FULLposition.  
WARNING: Do not operate snow  
thrower if weather conditions impair  
visibility. Throwing snow during a  
heavy, windysnowstormcanblindyou  
andbehazardoustothesafeoperation  
of the snow thrower.  
4. Push the primer four (4) times if the temperature is  
below 15°F, or two (2) times if temperature is between  
15° and 50°F. If temperature is above 50°F, priming is  
not necessary.  
NOTE: Over priming may cause flooding, preventing the  
engine from starting. If you do flood the engine, wait a few  
minutes before attempting to start and DO NOT push the  
primer.  
5. Pull recoil starter handle quickly. Do not allow starter  
rope to snap back.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
GENERAL RECOMMENDATIONS  
LUBRICATION CHART  
SAE 5W-30 Motor Oil  
The warranty on this snow thrower does not cover items  
that have been subjected to operator abuse or negligence.  
To receive full value from the warranty, operator must  
maintain snow thrower as instructed in this manual. Some  
adjustments will need to be made periodically to properly  
maintain your snow thrower.  
See “ENGINE” in  
Maintenance section  
General  
Purpose  
Grease  
All adjustments in the Service and Adjustments section of  
this manual should be checked at least once each season.  
Once a year, you should replace the spark plug and  
check belts for wear. A new spark plug will help your  
engine run better and last longer.  
Pivot points  
Follow the maintenance schedule in this manual.  
NOTE: Use only Original Equipment Manufacturer (OEM)  
parts to service this unit. Failure to do so can cause the unit  
to malfunction and pose a risk of injury to the operator.  
BEFORE EACH USE  
1. Check engine oil level.  
2. Check for loose fasteners.  
3. Checkcontrolstobesuretheyarefunctioningproperly.  
LUBRICATION  
Keep your snow thrower well lubricated  
(See “LUBRICATION CHART”).  
Engine  
oil  
Auger  
grease fittings  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
SNOW THROWER  
Checkthecrankcaseoillevelbeforestartingtheengineand  
after each five (5) hours of continuous use. Tighten oil fill  
cap / dipstick securely each time you check the oil level.  
Alwaysobservesafetyruleswhenperformingmaintenance.  
TIRES  
TO CHANGE ENGINE OIL  
Maintain proper air pressure in both tires  
(14–17 P.S.I.).  
Keep tires free of gasoline / oil, which can harm rubber.  
Determine temperature range anticipated before next oil  
change.AlloilmustmeetAPIserviceclassificationSG–SL.  
Be sure snow thrower is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
NOTE:Tosealtirepuncturesandpreventflattiresduetoslow  
leaks, tire sealant may be purchased from your local parts  
dealer. Tire sealant also prevents tire dry rot and corrosion.  
NOTE: The left side wheel may be removed from snow  
thrower for easier access to the oil drain plug and place-  
ment of a suitable container. The unit tilted, resting on the  
frame with the left wheel removed, will help drain any oil  
trapped inside the engine. (See “TO REMOVE WHEELS”  
in the Service and Adjustments section of this manual).  
1. Remove safety ignition key and disconnect spark plug  
wire from spark plug. Place wire where it cannot come  
in contact with spark plug.  
V-BELTS  
Check V-belts for deterioration and wear after every 50  
hours of operation and replace if necessary. The belts  
are not adjustable. Replace belts if they begin to slip from  
wear. (See “TO REMOVE BELT COVER” in the Service  
and Adjustments section of this manual).  
TheV-beltsonyoursnowthrowerareofspecialconstruction  
andshouldbereplacedbyoriginalequipmentmanufacturer  
(OEM) belts available from your dealer. Using other than  
OEMbeltscancausepersonalinjury/damagetothethrower.  
2. Clean area around drain plug.  
3. Remove drain plug and drain oil in a suitable container.  
4. Install drain plug and tighten securely.  
5. Wipe off any spilled oil from snow thrower and engine.  
6. Install left wheel (if removed for draining oil). Be sure to  
install klick pin into proper hole in wheel axle (See “TO  
REMOVE WHEELS” in the Service and Adjustments  
section of this manual).  
7. Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine.  
8. Refill engine with oil through oil dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCTSPECIFICATIONSsectionofthismanual.  
9. Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil at “FULLline on dipstick.  
AUGER GEAR CASE  
Thegearcasewasfilledwithlubricanttotheproperlevel  
at the factory. The only time the lubricant needs atten-  
tion is if service has been performed on the gear case.  
If lubricant is required, use only Ronex ED #1 grease.  
TRACTION DRIVE SYSTEM  
DO NOT lubricate the drive components inside the snow  
thrower. The sprockets, hex shafts, drive disc and friction  
wheel require no lubrication. The bearings and bushings  
are lifetime lubricated and require no maintenance.  
CAUTION:Anylubricatingoftheabovecompo-  
nents can cause contamination of the friction  
wheel and damage to the drive system of your  
snow thrower.  
10. Wipe off any spilled oil.  
ENGINE  
See engine manual.  
MUFFLER  
Inspect and replace corroded muffler as it could create a  
fire hazard and/or damage.  
LUBRICATION  
Use only high quality detergent oil rated with API service  
classification SG–SL. Select the oil's SAE viscosity grade  
according to your expected operating temperature.  
SPARK PLUG  
Replacesparkplugatthebeginningofeachseasonorafter  
every100hoursofoperation,whicheveroccursfirst. Spark  
plug type and gap setting are shown in the “PRODUCT  
SPECIFICATIONS” section of this manual.  
CLEANING  
IMPORTANT: For best performance, keep snow thrower  
housing free of any dirt or trash. Clean the outside of your  
snow thrower after each use.  
WARNING: Removesafetyignitionkey  
and disconnect spark plug wire from  
spark plug. Place wire where it cannot  
come in contact with spark plug.  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improve starting in cold weather, these multi-viscosity oils  
will result in increased oil consumption when used above  
32°F. Check your engine oil level more frequently to avoid  
possible engine damage from running low on oil.  
Keepfinishedsurfaces/wheelsfreeofgasoline,oil,etc.  
We do not recommend using a garden hose to clean  
yoursnowthrowerunlesstheelectricalsystem,muffler  
and carburetor are covered to keep water out. Water  
in engine can result in shortened engine life.  
Changetheoilafterevery25hoursofoperationoratleastonce  
ayearifthesnowthrowerisnotusedfor25hoursinoneyear.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
To replace the capscrew/shear bolts:  
1. Disengage all controls and move throttle control to  
STOP position. Wait for all moving parts to stop.  
2. Remove safety ignition key and disconnect spark plug  
wire from spark plug. Place wire where it cannot come  
in contact with spark plug.  
WARNING: To avoid serious injury, before  
performing any service or adjustments:  
1. Be sure the on/off switch is in the  
OFF position.  
2. Remove safety ignition key.  
3. Align holes in impeller hub with holes in impeller shaft  
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear  
bolts. Install 1/4-20 locknuts and tighten securely.  
3. Make sure the augers and all moving  
parts have completely stopped.  
4. Disconnect spark plug wire from  
spark plug and place wire where it  
cannot come in contact with plug.  
CAUTION: Do not substitute. Use only original  
equipment capscrew/shear bolts as supplied  
with your snow thrower.  
SNOW THROWER  
TO ADJUST SNOW THROWER HEIGHT  
4. Insertsafetyignitionkeyandreconnectsparkplugwire  
to spark plug.  
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”  
in the Operation section of this manual.  
1/4-20  
LOCKNUT  
1/4-20 x 1-5/8  
CAPSCREW /  
SHEAR BOLT  
1/4-20 x 2  
SHOULDER /  
SHEAR BOLT  
CHUTE DEFLECTOR  
The chute deflector, attached to the top of the discharge  
chute, is provided to direct discharging snow away from  
the operator. If the deflector becomes damaged, it should  
be replaced.  
IMPELLER HUB  
IMPELLER  
SHAFT  
WARNING: To avoid serious injury,  
never operate your snow thrower with  
the deflector removed or damaged.  
Tochangedirectionand/ordistancesnowisdischarged,  
see “TO CONTROL SNOW DISCHARGE” in the Op-  
eration section of this manual.  
AUGER  
HUB  
SHEAR BOLTS (See Fig. 20)  
AUGER SHEAR BOLTS  
1/4-20  
Both right and left-hand augers are secured to the auger  
shaftwithaspacer, shearboltandhexnut. Shouldaforeign  
object or ice become lodged in the augers, the shear bolts  
are designed to break, preventing damage to any other  
components. If one or both augers do not turn when auger  
control lever is engaged, check to see if one or both of the  
bolts have sheared. To replace the shear bolts:  
LOCKNUT  
AUGER HUB  
FIG. 20  
AUGER SHAFT  
TO REMOVE BELT COVER (See Fig. 21)  
1. Remove the two (2) screws securing belt cover to  
frame.  
2. Remove belt cover.  
1. Disengage all controls and move throttle control to  
STOP position. Wait for all moving parts to stop.  
2. Remove safety ignition key and disconnect spark plug  
wire from spark plug. Place wire where it cannot come  
in contact with spark plug.  
3. Align hole in auger hub with hole in auger shaft and  
install a new 1/4-20 x 2" shear bolt. Install 1/4-20  
lock nut and tighten securely.  
Replace belt cover by installing cover and screws and  
tighten securely.  
BELT  
COVER  
CAUTION: Do not substitute. Use only original  
equipment shear bolts as supplied with your  
snow thrower.  
4. Insertsafetyignitionkeyandreconnectsparkplugwire  
to spark plug.  
IMPELLER SHEAR BOLTS  
The impeller is secured to the impeller shaft with two (2)  
capscrew/shearboltsandhexnuts. Shouldaforeignobject  
or ice become lodged in the impeller, the capscrews are  
designed to break, preventing damage to any other com-  
ponents. If impeller does not turn when auger control lever  
is engaged, check to see if the capscrews have sheared.  
FRAME  
SCREWS  
FIG. 21  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE BELTS (See Fig. 22)  
8. RELIEVE TENSION ON TRACTION DRIVE BELT  
IDLER and remove traction drive belt from around  
pulleys.  
The auger and traction drive belts are not adjustable. If  
the belts are damaged or begin to slip from wear, they  
should be replaced. It is recommended that the belt(s) be  
replaced by a service center/department.  
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into  
the square hole in idler arm and rotate ratchet clockwise  
to relieve tension.  
9. With tension relieved on idler, install new traction drive  
belt around pulleys and inside belt keepers.  
10. Install clutch rod in swing plate; secure with hairpin.  
11. Placeaugerbeltaroundandinsidethegrooveofauger  
pulley only.  
12. While your assistant slowly raises handles to rejoin  
the auger housing and frame assembly, pull up on the  
auger belt and squeeze sides together above pulley  
so belt is fully seated in groove of pulley.  
13. Move idler arm so it does not hit impeller pulley as you  
bring snow thrower completely together and check  
carefully for proper routing of belts. If auger belt has  
becomedislodgedfromthepulley(bycatchingtheidler  
arm bracket while bringing snow thrower together),  
separate the snow thrower and repeat step 12. Belt  
must be fully seated in pulley groove when bringing  
the snow thrower together.  
NOTE: It is recommended that both the auger and traction  
drive belt be replaced at the same time.  
The V-belts on your snow thrower are of special construc-  
tion and should be replaced by original equipment manu-  
facturer (OEM) belts available from your nearest service  
center/department. Using other than OEM belts can cause  
personal injury or damage to the snow thrower.  
WARNING: Belt replacement requires  
separation of the snow thrower. While  
separating the auger housing from the  
frame assembly, it is important that  
an assistant stand in the operating  
position and hold the snow thrower  
handles. Serious personal injury and/  
or damage to the unit could occur if  
the snow thrower should fall during  
the belt changing process.  
FRAME  
ASSEMBLY  
AUGER  
HOUSING  
14. Install the two (2) hex bolts and tighten securely.  
15. INSTALLENGINEPULLEY-Placebeltinpulleygroove  
and slide pulley on crankshaft. Install flat washer, bolt  
and tighten securely (41-47 N-m torque). Make sure  
belt is inside belt keeper.  
16. INSTALL BELT COVER and two (2) screws. Tighten  
securely.  
17. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-  
CHARGE CHUTE / CHUTE ROTATER HEAD” in the  
Assembly / Pre-Operation section of this manual.  
HANDLES  
1. REMOVE GASOLINE FROM FUEL TANK - Drain  
gasoline from fuel tank into a suitable container, out-  
doors, away from fire or flame. Wipe up any spilled  
gasoline.  
BELT KEEPER  
TRACTION DRIVE BELT  
ENGINE  
2. REMOVE DISCHARGE CHUTE - Loosen locknut  
securing chute rotator head to mounting bracket only  
enough to allow chute rotator head to be raised and  
discharge chute to be removed from snow thrower.  
3. REMOVE BELT COVER - See “TO REMOVE BELT  
COVER” in this section of this manual.  
4. REMOVEENGINEPULLEY-Removebolt,flatwasher  
securingpulleytoenginecrankshaft. Removeoutside  
(auger) pulley only from crankshaft.  
5. SEPARATE SNOW THROWER - With your assistant  
standing in the operating position holding the handles,  
remove the two (2) bolts holding the auger housing  
and frame together.  
FLAT WASHER  
PULLEY  
BOLT  
AUGER  
BELT  
IDLER ARM  
SQUARE  
HOLE  
CLUTCHING  
IDLER ARM  
BRACKET  
AUGER  
HOUSING  
FRAME  
AUGER PULLEY  
BOLTS  
WARNING: As the last bolt is removed,  
haveyourassistantcarefullylowerthe  
handles down to the ground.  
6. REMOVE HAIRPIN FROM CLUTCH ROD and re-  
move clutch rod from swing plate. Tip swing plate  
forward.  
7. REMOVE AUGER BELT from around pulley.  
FIG. 22  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REMOVE WHEELS (See Fig. 23)  
TO ADJUST CABLE TENSION (See Fig. 24)  
Remove the klik pin and remove wheel from axle.  
Adjust cable tension by turning the adjuster turn buckle,  
located on the right hand cable. Grasp the long section  
tightly and turn the short section to lengthen the adjuster.  
Adjust until cable is snug.  
IMPORTANT: When installing wheel, be sure to use the  
axle hole closest to the end of the shaft – do not use the  
hole in the wheel hub (if equipped). Inner hole in axle and  
holeinwheelhubarenotusedforyourmodelsnowthrower.  
KLIK PIN (INSTALL  
IN OUTER HOLE  
OF AXLE ONLY)  
OUTER HOLE  
ADJUSTER TURN  
BUCKLE  
AXLE  
WHEEL  
WHEEL HUB  
FIG. 23  
FIG. 24  
NOTE: To seal punctures or prevent flat tires due to slow  
leaks, tire sealant may be purchased from your local parts  
dealer. Tire sealant also prevents tire dry rot and corrosion.  
ENGINE  
See engine manual.  
CARBURETOR  
Your carburetor is not adjustable. Engine performance  
should not be affected at altitudes up to 7,000 feet (2,134  
meters). If your engine does not operate properly due to  
suspected carburetor problems, take your snow thrower  
to a qualified service center.  
ENGINE SPEED  
Never tamper with the engine governor, which is factory set  
for proper engine speed. Overspeeding the engine above  
the factory high speed setting can be dangerous and will  
void the warranty. If you think the engine-governed high  
speed needs adjusting, contact a qualified service center,  
which has proper equipment and experience to make any  
necessary adjustments.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your snow thrower for storage at  
Empty the fuel tank by starting the engine and letting  
it run until the fuel lines and carburetor are empty.  
the end of the season or if the unit will not be used for 30  
days or more.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
Use fresh fuel next season.  
WARNING: Never store the snow  
throwerwithgasolineinthetankinside  
a building where fumes may reach an  
open flame, spark or pilot light as on a  
furnace, water heater, clothes dryer or  
gasappliance. Allowtheenginetocool  
before storing in any enclosure.  
NOTE: Fuel stabilizer is an acceptable alternative in min-  
imizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not drain the  
gas tank and carburetor if using fuel stabilizer.  
SNOW THROWER  
When snow thrower is to be stored for a period of time,  
clean it thoroughly, remove all dirt, grease, leaves, etc.  
Store in a clean, dry area.  
1. Clean entire snow thrower (See “CLEANING” in the  
Maintenance section of this manual).  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean engine  
oil. (See “ENGINE” in the Maintenance section of this  
manual).  
CYLINDER  
1. Remove spark plug.  
2. Pour one ounce (29 ml) of oil through spark plug hole  
into cylinder.  
3. Pullrecoilstarterhandleslowlyafewtimestodistribute  
oil.  
4. Replace with new spark plug.  
2. Inspect and replace belts, if necessary (See “TO RE-  
PLACEBELTSintheServiceandAdjustmentssection  
of this manual).  
3. Lubricate as shown in the Maintenance section of this  
manual.  
4. Besurethatallnuts,bolts,screws,andpinsaresecurely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
5. Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
OTHER  
Remove safety ignition key; store it in a safe place.  
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
ENGINE  
See engine manual.  
If possible, store your snow thrower indoors and cover  
it to protect it from dust and dirt.  
Cover your snow thrower with a suitable protective  
cover that does not retain moisture. Do not use plastic.  
Plastic cannot breathe, which allows condensation to  
form and will cause your snow thrower to rust.  
FUEL SYSTEM  
IMPORTANT: It is important to prevent gum deposits from  
forming in essential fuel system parts such as carburetor,  
fuel hose, or tank during storage. Also, alcohol blended  
fuels (called gasohol or using ethanol or methanol) can  
attract moisture which leads to separation and formation  
of acids during storage. Acidic gas can damage the fuel  
system of an engine while in storage.  
IMPORTANT: Never cover snow thrower while engine/ex-  
haust area is still warm.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
See appropriate section in manual unless directed to an authorized service center/department.  
PROBLEM  
CAUSE  
CORRECTION  
Does not start  
1. Fuel shut-off valve (if so  
equipped) in OFF position.  
2. Safety ignition key  
is not inserted.  
1. Turn fuel shut-off valve to OPEN position.  
2. Insert safety ignition key.  
3. Out of fuel.  
4. ON/OFF switch is OFF.  
3. Fill fuel tank with fresh, clean gasoline.  
4. ON/OFF switch to ON position.  
5. Choke in OFF position.  
6. Primer not depressed.  
7. Engine is flooded.  
8. Spark plug wire is  
disconnected.  
9. Bad spark plug.  
10. Stale fuel.  
5. Move to FULL position.  
6. Prime as instructed in the Operation section of this manual.  
7. Wait a few minutes before restarting, DO NOT prime.  
8. Connect wire to spark plug.  
9. Replace spark plug.  
10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
11. Water in fuel.  
Loss of power  
1. Spark plug wire loose.  
2. Throwing too much snow.  
3. Fuel tank cap is covered  
with ice or snow.  
1. Reconnect spark plug wire.  
2. Reduce speed and width of swath.  
3. Remove ice and snow on and around fuel tank cap.  
4. Dirty or clogged muffler.  
4. Clean or replace muffler.  
Engine idles or  
runs roughly  
1. Choke is in FULL position.  
2. Blockage in fuel line.  
3. Stale fuel.  
4. Water in fuel.  
5. Carburetor is in need of  
adjustment or overhaul.  
1. Move choke to OFF position.  
2. Clean fuel line.  
3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.  
5. Contact an authorized service center/department.  
Excessive  
vibration  
1. Loose parts or damaged  
augers or impeller.  
1. Tighten all fasteners. Replace damaged parts. If vibration  
remains, contact an authorized service center/department.  
Recoil starter  
is hard to pull  
1. Frozen recoil starter.  
1. See “IF RECOIL STARTER HAS FROZEN”  
in the Operation section of this manual.  
Loss of traction 1. Drive belt is worn.  
1. Check / replace drive belt.  
2. Check / reinstall drive belt.  
drive / slowing  
of drive speed  
2. Drive belt is off of pulley.  
3. Friction drive wheel is worn. 3. Contact an authorized service center/department.  
Loss of snow  
discharge or  
slowing of  
1. Auger belt is off of pulley.  
2. Auger belt is worn.  
3. Clogged discharge chute.  
1. Check / reinstall auger belt.  
2. Check / replace auger belt.  
3. Clean snow chute.  
4. Remove debris or foreign object from augers / impeller.  
snow discharge 4. Augers / impeller jammed.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
AUGER HOUSING / IMPELLER ASSEMBLY  
1
3 (5x)  
4 (5x)  
KEY  
PART  
NO.  
NO.  
DESCRIPTION  
AUGER HOUSING  
SCRAPPER BAR  
CARRIAGE BOLT 5/1618 X .625  
NUT 5/1618  
2
1
2
3
4
404930X428  
404933X479  
72270505  
155377  
01.07.003-A  
2
KEY  
PART  
NO.  
1
NO.  
DESCRIPTION  
1
2
420497X479  
420498X479  
AUGER ASSEMBLY 30 LH  
AUGER ASSEMBLY 30 RH  
01.07.019-A  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
AUGER HOUSING / IMPELLER ASSEMBLY  
5
11  
6
11  
7
15  
16  
14  
12  
8
11  
4
13  
17  
12  
3
10  
11  
1
37  
9
9
2
9
37  
33  
32  
34  
30  
31  
31  
26  
36  
29  
20  
27  
21  
22  
28  
23  
23  
25  
24  
35  
22  
21  
2
(EXPLODED)  
18  
19  
01.07.026-C  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
AUGER HOUSING / IMPELLER ASSEMBLY  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
7
8
175321X479  
427148  
188909  
427146  
175322  
178675X008  
192199  
405400  
73800400  
74780426  
427942  
163183  
427145  
427154  
73900600  
180355  
194189  
407760  
427302  
427345  
407770  
407762  
174697  
407763  
407764  
189282  
407758  
174683  
427147  
7836M  
IMPELLER  
GEARBOX ASSEMBLY  
BEARING  
IMPELLER PULLEY  
DISCHARGE BASE  
CORNER BRACKET  
CLEAN OUT TOOL  
TOOL CLIP  
NUT 1/4-20  
SCREW 1/4-20 X .625  
NUT 5/16-18  
SCREW 5/16-18 X .625  
IMPELLER HUB  
IMPELLER SLEEVE  
NUT 3/8-16  
CARRIAGE BOLT  
SCREW 13-16 X .625  
PLUG  
GEARBOX COVER RH  
GASKET  
SEAL  
BEARING  
THRUST WASHER 1.00  
WORM GEAR  
AUGER SHAFT  
SQUARE KEY  
BEARING  
THRUST WASHER  
IMPELLER SHAFT  
ROLL PIN  
THRUST WASHER  
THRUST BEARING  
BEARING  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
174681  
174684  
407769  
407768  
407767  
427317  
192090  
O-RING  
SCREW 5/16-18 X .750  
GEARBOX COVER LH  
SHEAR BOLT  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
AUGER HOUSING / IMPELLER ASSEMBLY  
3
4
2
4
KEY  
PART  
NO.  
NO.  
DESCRIPTION  
1
2
3
4
174762X479  
178777X479  
72270506  
751153  
SKID PLATE LH  
SKID PLATE RH  
CARRIAGE BOLT 5/1618 X .75  
NUT 5/1618  
01.11.001-A  
1
3
2
3
1
1
2
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
420478  
411939  
179582  
AUGER BEARING  
BEARING PLUG  
SCREW 5/1618 X 1.00  
3
01.07.024-B  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
CONTROL PANEL / DISCHARGE CHUTE  
5
7
15  
3
16  
*14  
*11  
2
4
10  
6
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
6
1
2
3
4
420315X428  
178633X428  
420673  
CHUTE WELDMENT  
DEFLECTOR WELDMENT  
DEFLECTOR CONTROL ASSEMBLY  
DEFLECTOR SEAL  
*13  
1
*12  
420325  
5
6
414280  
128415  
KNOB BLACK  
POP RIVET  
7
8
9
*10  
*11  
*12  
*13  
*14  
15  
16  
17501010  
419821  
419822X004  
179829  
191730  
72250505  
751153  
184505  
420679  
420672  
SCREW 10-24 X .625  
CHUTE SNOW SHIELD  
SHIELD RETAINER STRAP  
SHOULDER BOLT 1/4-20 X .375  
NUT 1/4-20  
CARRIAGE BOLT 3/8-16 X .625  
NUT 5/16-18  
DEFLECTOR SPRING  
(SERVICE PART) DEFLECTOR CONTROL  
(SERVICE PART) DEFLECTOR CABLE BLK  
6
9
8
01.09.015-A  
NOTE:  
1. ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.  
2. ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
CONTROL PANEL / DISCHARGE CHUTE  
2
2
1
*3  
*7  
*6  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
*3  
*4  
*5  
*6  
*7  
428272  
17501010  
420678  
405932  
420675  
428273  
428310  
LEVER/CABLE ROTATOR ASSEMBLY  
SCREW 10-24 X .625  
ROTATOR HEAD  
ROTATOR PIVOT BRACKET  
PULLEY PIVOT  
CABLE ASSEMBLY ADJUSTABLE  
CABLE ASSEMBLY HEAT SHIELD  
*4  
01.09.010-A  
*5  
NOTES:  
1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.  
2
01.15.009-A  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
421249  
74041024  
STEER CABLE  
SCREW 1024 X 1.50  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
HANDLES  
SNOW THROWER - MODEL 961940009 (96194000900)  
3
KEY  
NO.  
PART  
NO.  
3
DESCRIPTION  
1
2
3
4
419798X479  
419799X479  
74780524  
751153  
LOOP HANDLE LH  
LOOP HANDLE RH  
SCREW 5/1618 X 1.50  
NUT 5/1618  
4
4
4
1
3
4
3
2
01.08.004-B  
4
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
412675X004  
414572  
178831  
169675  
17060410  
421252X004  
INTERLOCK SPRING  
INTERLOCK CAM  
TORSION SPRING  
RETAINER  
SCREW 1/420 X .625  
INTERLOCK STOP  
3
2
5
1
01.08.007-B  
6
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
HANDLES  
10  
2
11  
7
4
8
9
9
5
7
6
1
12  
3
13  
8
13  
14  
14  
01.08.002-F  
12  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
7
412683X479  
424517X479  
424516X479  
426917X008  
426918X008  
412677  
CONTROL PANEL  
CONTROL LEVER LH  
CONTROL LEVER RH  
TRACTION ROD ARM  
IMPELLER ROD ARM  
INTERLOCK ROD  
SPACER  
421613  
8
9
10  
11  
12  
13  
14  
169675  
17060410  
414280  
414281  
178899  
19131316  
72120618  
RETAINER  
SCREW 1/4-20 X .62  
KNOB BLACK  
KNOB RED  
HANDLE KNOB  
WASHER 3/8  
CARRIAGE BOLT 3/8-16 X 2.25  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
HANDLES  
SNOW THROWER - MODEL 961940009 (96194000900)  
2
10  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
10  
180480  
405740  
180445  
187716  
180447  
178669  
180926  
72270505  
155377  
169675  
IMPELLER ROD  
TRACTION ROD  
SHIFTER ROD TOP  
SHIFTER ROD BOTTOM  
SPRING SLEEVE  
IMPELLER SPRING  
TRACTION SPRING  
CARRIAGE BOLT 5/16-18 X .75  
NUT 5/16-18  
10  
1
3
8
RETAINER  
9
4
5
7
10  
5
6
01.12.001-E  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
HANDLES  
SNOW THROWER - MODEL 961940009 (96194000900)  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
4
419797X479  
418313X479  
428867  
LOWER TUBE  
PIVOT SUPPORT  
BOLT 5/16-18 X .750  
SCREW 3/8-16 X 1.00  
17000616  
2
4
3
4
4
01.05.004-C  
4
7
4
5
3
2
KEY  
PART  
NO.  
NO.  
DESCRIPTION  
1
2
3
4
5
6
7
182906  
178668  
180927  
184471  
175262  
178770  
183784  
CONSOLE PANEL  
HEADLIGHT BEZEL  
FLOOD HEADLIGHT  
SHOULDER SCREW 1024 X .625  
SCREW 1024 X 1.25  
WIRE HARNESS  
1
4
5
6
01.10.007-B  
BULB  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
DRIVE  
6
7
1b  
4
8
3
1b  
7
1a  
2
3
5
KEY  
PART  
NO.  
NO.  
DESCRIPTION  
AXLE ASSEMBLY (assy of 1a,1b)  
AXLE SHAFT  
ROLL PIN 3/16 X 1.50  
SPROCKET  
THRUST WASHER  
BEARING  
SCREW 5/1618 X .625  
SCREW 5/1618 X .500  
KLIK PIN 1/4 X 1.50  
SQUARE KEY  
4
1
404923  
404307  
9465M1  
402691  
174697  
179830  
146315  
17490508  
155443  
189282  
01.03.002-A  
6
1a  
1b  
2
3
4
5
6
7
8
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
DRIVE  
SNOW THROWER - MODEL 961940009 (96194000900)  
42 EXPLODED  
46  
2
45  
48  
16  
14  
51  
17  
1
18  
47  
49  
15  
15  
50  
9
12  
11  
20  
22  
11  
53  
13  
24  
9
19  
9
23  
10  
11  
53  
52  
4
34  
8
53  
7
21  
6
24  
5
33  
23  
31  
53  
3
33  
38  
30  
29  
32  
28  
26  
53  
35  
27  
24  
26  
36  
4
23  
37  
42  
44  
43  
39  
53  
25  
24  
41  
40  
01.02.013-A  
39  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
DRIVE  
SNOW THROWER - MODEL 961940009 (96194000900)  
KEY  
NO.  
PART  
NO.  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
DESCRIPTION  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
179831  
175344  
178613  
74760514  
12000012  
402187  
401619  
417234  
401984X479  
180135  
402652  
428288  
184471  
410877  
413429X479  
402689  
414557  
178828  
402504X008  
401820  
198791  
402393  
17541008  
402511  
418894X479  
132010  
428867  
RUBBER RING  
BEARING  
WHEEL HUB  
SCREW 5/16-18-.875  
RETAINER RING  
SPROCKET SHAFT  
CHAIN  
SPROCKET WELDMENT  
SHIFTER BRACKET  
SPRING  
PLATE PIVOT ROD  
E-RING .375  
SHOULDER SCREW  
BOTTOM PAN  
SPRING BRACKET  
DRIVE PLATE ASSEMBLY  
IDLER SPRING  
IDLER SPRING  
PULLEY SHAFT  
DRIVE PLATE  
1
198875  
SPEED SELECTOR  
ASSEMBLY  
SCREW 10-24 X .625  
END PLATE  
SCREW 5/16-18 X .50  
WASHER  
CONTROL ARM  
CLEVIS PIN  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
17501010  
402685X428  
17490508  
57079  
405485  
198580  
403097X004  
402881  
403096 X004 SHIFTER BRACKET  
SHIFTER PLATE  
SHOULDER BOLT  
191730  
NUT 1/4-20  
402856X004  
416717X004  
187101  
700279  
427542  
402568  
169675  
401732  
402310  
12000036  
402878  
751153  
408981  
73930500  
198176X479  
CLUTCH PLATE  
CLUTCH BRACKET  
SHIFTER LINK  
RETAINER  
CONTROL SHAFT  
CLUTCH ROD  
RETAINER  
SHIFTER YOKE  
PIVOT ROD  
RETAINER  
RETURN SPRING  
NUT 5/16-18  
BEARING  
NUT 5/16-18  
RUBBER WHEEL PLATE  
BEARING  
PULLEY HALF  
SCREW 10-24 X .50  
SPACER BEARING  
SWING PLATE  
NUT 3/8-16  
SCREW 5/16-18 X .750  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
CHASSIS / ENGINE / PULLEYS  
2
3
2
3
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
- -  
1
2
428173  
418694X428  
150406  
COMPLETE LCT ENGINE  
FRAME  
BOLT 3/8-16  
1
01.00.034-A  
3
428867  
SCREW 5/16-18 X .750  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
427963X428  
ENGINE MOUNTING PLATE  
01.01.004-A  
1
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
418601  
17490408  
COVER ASSEMBLY  
SCREW 1/4-20 X .50  
2
01.21.014-B  
2
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
CHASSIS / ENGINE / PULLEYS  
27  
23  
22  
13  
21  
20  
25  
24  
13  
21  
19  
26  
15  
18  
11  
17  
12  
16  
13  
14  
7
5
9
6
4
1
3
10  
2
8
01.21.020-A  
KEY  
NO.  
PART  
NO.  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
DESCRIPTION  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
74780520  
851084  
19132005  
425934  
SCREW 5/16-18 X 1.25  
SCREW 3/8-24 X 1 .375  
WASHER  
PULLEY ENG IMPELLER  
PULLEY ENG TRACTION  
SCREW 5/16-24 X 1.00  
LOCKWASHER 5/16  
BELT GUIDE  
LOCKWASHER 5/16  
IDLER BUSHING  
WASHER  
SCREW 5/16-24 X 1.25  
SCREW 3/8-16 X .750  
1
2
3
4
5
6
7
8
419888  
427304  
423723X479  
180523  
423990X479  
426589  
74780524  
424297  
751153  
428867  
427576  
IMPELLER BELT  
TRACTION BELT  
IDLER ARM BRACKET  
IDLER PULLEY  
IDLER BRACKET  
NUT 5/16-18  
SCREW 5/16-18 X 1.50  
SHOULDER BOLT 5/16-18 X .50  
NUT 5/16-18 LOCK  
SCREW 5/16-18 X .625  
TRACTION IDLER BRACKET  
TRACTION PULLEY  
WASHER  
425933  
74610516  
10040500  
155452  
11050500  
175331  
19112206  
74610520  
74760608  
9
10  
11  
12  
13  
14  
180522  
59289  
73800500  
NUT 5/16-18  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
WHEELS  
SNOW THROWER - MODEL 961940009 (96194000900)  
2
2
3
17  
1
4
23  
20  
16  
15  
19  
22  
5
6
7
17  
21  
18  
18  
24  
8
9
16  
10  
20  
23  
22  
11  
12  
21  
14  
19  
14  
13  
13  
11  
10  
12  
9
8
2
7
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
6
5
4
3
1
2
3
4
5
6
7
8
405161  
184471  
12000045  
192126  
182466  
187622  
194941  
179139  
189282  
194940  
174697  
193506X479  
179148X479  
17490508  
194943X008  
194944X008  
181847  
17600406  
405077  
700279  
85179  
193885  
182015  
194939X008  
COVER  
SHOULDER SCREW  
RETAINER RING  
WHEEL DRIVER  
RETAINER RING  
WHEEL LOBE  
CLUTCH SLIDE  
SPRING  
1
01.15.001-A  
2
9
SQUARE KEY  
AXLE LOBE  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
THRUST WASHER  
STEERING YOKE  
STEERING BRACKET  
SCREW 5/1618 X .50  
PIVOT BRACKET  
BELLCRANK  
BELLCRANK PIN  
SCREW 1/420 X .375  
STEERING LINK  
RETAINER  
RETAINER  
SPRING  
LEVER PIN  
PIVOT BRACKET  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
WHEELS  
SNOW THROWER - MODEL 961940009 (96194000900)  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
192092X421  
192093X421  
WHEEL 16 X 4.80 X LH  
WHEEL 16 X 4.80 X RH  
1
2
01.06.005-A  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
2
3
410293  
410294  
17060410  
CABLE BRACKET LH  
CABLE BRACKET RH  
SCREW 1/420 X .625  
3
1
2
01.15.003-A  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
BAG OF PARTS  
4
KEY  
NO.  
PART  
NO.  
6
DESCRIPTION  
5
1
2
198563  
169675  
POWER CORD  
8
RETAINER PIN  
WRENCH  
REMOTE SPRING  
SHOULDER BOLT 1/4-20  
LOCKNUT 1/4-20  
7
3
4
5
6
180684X008  
184505  
179829  
3
191730  
10  
9
7
8
9
10  
11  
12  
72250505  
751153  
73800600  
19131316  
192090  
CARRIAGE BOLT 5/16-18 X 5/8  
LOCKNUT 5/16-18  
LOCKNUT 3/8-16  
WASHER 3/8  
SHEAR BOLT 1/4-20 X 1-13/16  
LOCKNUT 1/4-20  
2
73800400  
12  
1
01.14.003-B  
11  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
422663  
SAFETY IGNITION KEY  
1
01.14.009-A  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL 961940009 (96194000900)  
DECALS  
1
4
12  
9
6
10  
11  
1
3
KEY PART  
NO. NO.  
DESCRIPTION  
1
3
4
6
9
181037  
181035  
181042  
181033  
415475  
DECAL, DANGER  
DECAL, DANGER, DEFLECTOR  
DECAL, DANGER  
DECAL, INSTRUCTION  
DECAL, SPEED CONTROL  
DECAL, REMOTE DEFLECTOR CONTROL  
DECAL, LH TRIGGER  
10 183730  
11 415399  
12 415398  
DECAL, RH TRIGGER  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects  
in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer pur-  
chaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part  
which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations  
and exclusions.  
1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-  
facturer's warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the  
purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by  
the purchaser unless such return is requested by the manufacturer.  
3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date  
of original purchase.  
4. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained  
in accordance with the instructions furnished. This Warranty does not apply to any product which has been sub-  
jected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the  
product.  
5. Exclusions: Excluded from this Warranty are belts, shear pins, normal wear, normal adjustments, standard hard-  
ware and normal maintenance.  
6. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.  
Should you have any unanswered questions concerning this Warranty, please contact:  
In Canada contact:  
HOP  
Poulan, Customer Service Department  
Customer Service Department  
5855 Terry Fox Way  
1030 Stevens Creek Road  
Mississauga, Ontario  
Augusta, GA 30907 USA  
L5V 3E4  
giving the complete mfg. ID#, serial number and date of purchase of your product and the name and address of the  
authorized dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED  
WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-  
RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied  
Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific  
legal rights, and you may have other rights which vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Petsafe Pet Fence In Ground Fence Kit User Manual
Philips CD Player AZ302S User Manual
Philips Portable DVD Player DVD951 User Manual
Philips Stereo System DCM3020 User Manual
Philips Vacuum Cleaner BP300 User Manual
Pioneer MP3 Player DEH P670MP User Manual
Polycom Telephone IP 300 User Manual
Procom Network Router Nav6 User Manual
PYLE Audio Computer Monitor PLD7HB User Manual
PYLE Audio Projector PRJSD188 User Manual