14" Wood Cutting Band Saw
(Model 28-248)
(Model 28-475X)
PART NO. 426-02-651-0055 - 06-10-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Download from Www.Somanuals.com. All Manuals Search And Download.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1.
2.
FOR YOUR OWN SAFETY, READ THE INSTRUCT-
13. USE RECOMMENDED ACCESSORIES. The use
of accessories and attachments not recom-
mended by Delta may cause damage to the
machine or injury to the user.
TION MANUAL BEFORE OPERATING THE
MACHINE. Learning the machine’s application,
limitations, and specific hazards will greatly
minimize the possibility of accidents and injury.
USE CERTIFIED SAFETY EQUIPMENT. Eye
protection equipment should comply with ANSI
Z87.1 standards, hearing equipment should
comply with ANSI S3.19 standards, and dust mask
protection should comply with MSHA/NIOSH
certified respirator standards. Splinters, air-borne
debris, and dust can cause irritation, injury, and/or
illness.
DRESS PROPERLY. Do not wear tie, gloves, or
loose clothing. Remove watch, rings, and other
jewelry. Roll up your sleeves. Clothing or jewelry
caught in moving parts can cause injury.
DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp
or wet locations or in rain can cause shock or
electrocution. Keep your work area well-lit to
prevent tripping or placing arms, hands, and
fingers in danger.
14. USE THE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating.
See the Extension Cord Chart for the correct size
depending on the cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.
15. SECURE THE WORKPIECE. Use clamps or a vise to
hold the workpiece when practical. Loss of control
of a workpiece can cause injury.
16. FEED THE WORKPIECE AGAINST THE DIRECTION
OF THE ROTATION OF THE BLADE, CUTTER, OR
ABRASIVE SURFACE. Feeding it from the other
direction will cause the workpiece to be thrown out
a high speed.
3.
4.
5.
6.
MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating
and changing accessories. Poorly maintained tools and
machines can further damage the tool or machine and/or
cause injury.
CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, and any other conditions
that may affect its operation. A guard or any other
part that is damaged should be properly repaired
or replaced. Damaged parts can cause further
damage to the machine and/or injury.
KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
KEEP CHILDREN AND VISITORS AWAY. Your shop is
a potentially dangerous environment. Children and visitors
can be injured.
REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of
a power failure, move the switch to the “OFF”
position. An accidental start-up can cause injury.
17. DON’T FORCE THE WORKPIECE ON THE
MACHINE. Damage to the machine and/or injury
may result.
18. DON’T OVERREACH. Loss of balance can make
you fall into a working machine, causing injury.
19. NEVER STAND ON THE MACHINE. Injury could occur if
the tool tips, or if you accidentally contact the cutting tool.
20. NEVER LEAVE THE MACHINE RUNNING UNATTEN-
DED. TURN THE POWER OFF. Don’t leave the machine
until it comes to a complete stop. A child or visitor could
be injured.
21. TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs. An
accidental start-up can cause injury.
22. MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental
start-up of a machine by a child or visitor could
cause injury.
23. STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION. A moment of inattention while
operating power tools may result in injury.
7.
8.
9.
10. USE THE GUARDS. Check to see that all guards
are in place, secured, and working correctly to
prevent injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high
speed, causing injury.
12. USE THE RIGHT MACHINE. Don’t force a
machine or an attachment to do a job for which it
was not designed. Damage to the machine and/or
injury may result.
24. THE DUST GENERATED by certain woods and
wood products can be injurious to your health.
Always operate machinery in well-ventilated areas,
and provide for proper dust removal. Use wood
dust collection systems whenever possible.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY RULES
FOR BAND SAWS
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1. DO NOT OPERATE THIS MACHINE UNTIL it is
15. TURN THE MACHINE “OFF” to back out of an
assembled and installed according to the
uncompleted or jammed cut.
instructions.
16. MAKE “RELIEF” CUTS prior to cutting long curves.
2. OBTAIN ADVICE from your supervisor,
instructor, or another qualified person if you are
not familiar with the operation of this tool.
17. TURN THE MACHINE “OFF” and wait for the blade
to stop prior to cleaning the blade area, removing
debris near the blade, removing or securing
workpiece, or changing the angle of the table. A
coasting blade can be dangerous.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections.
4. USE THE GUARDS WHENEVER POSSIBLE. Check
to see that they are in place, properly adjusted,
secured, and working correctly.
18. NEVER PERFORM LAYOUT, ASSEMBLY, or set-
up work on the table/work area when the machine is
running.
19. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs.
5. USE PROPER BLADE SIZE and type.
6. ADJUST THE UPPER BLADE GUIDE so that it is
about 1/8" above the workpiece.
7. PROPERLY ADJUST the blade tension, tracking,
20. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK
THE SWITCH IN THE “OFF” POSITION to prevent
unauthorized use.
blade guides, and blade support bearings.
8. KEEP ARMS, HANDS, AND FINGERS away from
the blade.
9. AVOID AWKWARD OPERATIONS and hand
positions where a sudden slip could cause a hand
to move into the blade.
21. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute,
1300 Sumner Avenue, Cleveland, OH 44115-2851
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please
refer to the American National Standards Institute
ANSI 01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor OSHA
1910.213 Regulations.
10. NEVER START THE MACHINE before clearing the
table of all objects (tools, scrap pieces, etc.).
11. NEVER START THE MACHINE with the workpiece
against the blade.
12. HOLD WORKPIECE FIRMLY against the table. DO
NOT attempt to saw a workpiece that does not have
a flat surface against the table.
13. HOLD WORKPIECE FIRMLY and feed into blade at
a moderate speed.
14. NEVER REACH UNDER THE TABLE while the
machine is running.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-
prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the
same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
MOTOR SPECIFICATIONS
Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
1. All grounded, cord-connected machines:
2. Grounded, cord-connected machines intended for use
on a supply circuit having a nominal rating less than 150
volts:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect
this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal
screw.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-
grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. A.
Repair or replace damaged or worn cord immediately.
GROUNDED OUTLET BOX
GROUNDED OUTLET BOX
GROUNDING
MEANS
CURRENT
CARRYING
PRONGS
ADAPTER
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. A
Fig. B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Grounded, cord-connected machines intended for
use on a supply circuit having a nominal rating between
150 - 250 volts, inclusive:
CURRENT
CARRYING
PRONGS
GROUNDED OUTLET BOX
If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. C, the
machine will have a grounding plug that looks like the
plug illustrated in Fig. C. Make sure the machine is
connected to an outlet having the same configuration as
the plug. No adapter is available or should be used with
this machine. If the machine must be re-connected for
use on a different type of electric circuit, the re-
connection should be made by qualified service
personnel; and after re-connection, the machine should
comply with all local codes and ordinances.
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. C
IN ALL CASES, MAKE CERTAIN
THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE HAVE A
Q U A L I F I E D E L E C T R I C I A N C H E C K T H E
RECEPTACLE.
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct
gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
Total Length
of Cord in Feet
Gauge of
Extension Cord
Ampere
Rating
Total Length
of Cord in Feet
Gauge of
Extension Cord
Volts
Volts
0-6
0-6
0-6
0-6
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
16 AWG
14 AWG
0-6
0-6
0-6
0-6
240
240
240
240
up to 50
50-100
100-200
200-300
18 AWG
16 AWG
16 AWG
14 AWG
6-10
6-10
6-10
6-10
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
14 AWG
12 AWG
6-10
6-10
6-10
6-10
240
240
240
240
up to 50
50-100
100-200
200-300
18 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
120
120
120
120
up to 25
25-50
50-100
100-150
16 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
240
240
240
240
up to 50
50-100
100-200
200-300
16 AWG
16 AWG
14 AWG
12 AWG
12-16
12-16
12-16
120
120
120
up to 25
25-50
14 AWG
12 AWG
12-16
12-16
12-16
240
240
240
up to 50
50-100
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. D
Fig. D
FUNCTIONAL DESCRIPTION
FOREWORD
Delta Models 28-248 and the 28-475X are 14" wood cutting band saws. The band saws have a quick tensioning blade
mechanism for ease with changing blades and applying tension to the blade. The Delta Models 28-248 and 28-475X
have large 16"x16" cast iron tables that can be tilted 45 degrees to the right and 8 degrees to the left. The band saws
also come with a 4" O.D. dust port for connecting the band saws to a dust collector.
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION
MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT
DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE INTENDED TO
ILLUSTRATE TECHNIQUE ONLY.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
1. Remove the cardboard box from around the packing
skid (A) Fig. 2.
2. Remove the two bolts (B) Fig. 2, with a 3/8" wrench,
that attach the motor to the packing skid (A)
A
B
Fig. 2
3. Remove the bolts that attach the stand (C) Fig. 3,
and the saw (D) to the the packing skid (A) with a 1/2"
wrench.
D
C
A
Fig. 3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BAND SAW PARTS
6
7
8
A
2
1
9
10
11
14
12
13
24
25
19
15
16
3
20
21
22
23
27
4
17
18
5
26
28
Fig. 4
Fig. 5
15. 5/16-18x1½" Hex Head Screw (4)
16. 5/16-18x3/4" Carriage Head Bolt (16)
1. Saw
2. Stand
17. #10-24x1/2" Socket Head Cap Screw (8)
18. #10-32x1/2" Pan Head Screw (4)
19. 5/16" Flat Washer (4)
20. 7/16" Jam Nut (2)
21. 7/16" Locknut (2)
3. Dust Chute
4. Top Plate
5. Stand Door
6. Motor and key (A)
7. Table
22. 5/16-18 Hex Nut (20)
23. #10-32 Hex Nut (4)
24. Table Handle (2)
8. Belt
9. On/Off Switch
10 Motor Bracket (2)
11. Dust Spout
12. Blade
25. Hinge Catch (2)
26. Door Latch
27. Hinge (2)
13. Table Insert
14. Motor Pulley
28. Cord Bushing
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL
THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE
INSTRUCTION MANUAL.
MOTOR BRACKET
TO STAND
1. Place the stand base on its side as shown in Fig. 6.
E
2. Align the two holes in the motor bracket (A) Fig. 7,
with the two holes in the stand. NOTE: ATTACH
MOTOR BRACKETS TO HOLES #1 AND 3 IN FRONT
STAND FLANGE (D) FIG. 6, AND HOLES #2 AND 4 IN
BACK STAND FLANGE (E).
5
4
4
3
3
2
1
2
1
D
NOTE: MAKE SURE THE SLOTS (C) FIG. 7, IN THE
MOTOR BRACKET (A), ARE POSITIONED CLOSER
TO THE OPENING OF THE STAND (D) THAN THE
BACK PANEL (E) OF THE STAND.
Fig. 6
Fig. 7
Fig. 8
Fig. 9
3. Insert a 5/16-18x3/4" carriage head bolt through the
hole in the motor bracket (A) Fig. 7, and the hole in the
stand.
E
C
A
C
A
4. Thread a 5/16-18 hex nut onto the screw and tighten
securely.
D
5. Repeat this process for the remaining hole in the
motor bracket.
6. Attach the other motor bracket to the stand in the
same manner.
MOTOR TO
MOTOR BRACKET
1. Place the motor (A) Fig. 8, on the motor brackets (B).
Align the holes in the motor with the holes on the motor
bracket.
A
B
B
2. Insert a 5/16-18x3/4" carriage head bolt through the
hole in the motor bracket and the hole in the motor.
3. Thread a 5/16-18 hex nut on to the screw. NOTE:
DO NOT COMPLETELY TIGHTEN THE BOLT AND
NUT AT THIS TIME.
4. Repeat this process for the three remaining holes in
the motor and motor bracket.
5. Place stand on its base as shown in Fig. 9.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP PLATE TO STAND
1. Place the top plate (A) Fig. 10, on the top of the
stand (B).
A
B
2. Align the six square holes on the top plate (A) Fig.
10, with the six square holes in the stand (B).
3. Align the two square holes on the side of the plate
(A) Fig. 10, with the two square holes on the side of the
stand (B).
4. Insert a 5/16-18x3/4" carriage head bolt through the
top plate and the stand. Thread a 5/16-18 hex nut on to
screw.
Fig. 10
A
5. Repeat this process for the five remaining holes in
the top of the plate and stand, and the two holes in the
side of the top plate and the stand. Make sure the door
opening is at least 13" wide before tightening the
screws.
DUST CHUTE
1. Insert the dust chute from inside the stand through
the opening (A) Fig. 11, in the top of the stand.
NOTE: MAKE SURE THE TAB (B) FIG. 12, IN THE
DUST CHUTE, ENGAGES THE CUTOUT (C) IN THE
TOP OF THE STAND.
Fig. 11
B
C
2. Align the two slotted holes (D) Fig. 13, in the bottom
of the dust chute with the two holes (E) Fig. 14, in the
stand.
Fig. 12
E
D
Fig. 13
Fig. 14
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BAND SAW USED WITH A DUST
COLLECTOR
B
B
A
3. If you are going to use your band saw with a dust
collector, attach the dust port as follows:
A. Align the four holes in the dust port (A) Fig. 15,
with the four holes in the side of the stand.
B. Insert a #10-32x1/2" pan head screw through
the two holes in the dust port (B) Fig. 15, and
stand. Thread a #10-32 hex nut onto the screw,
and tighten securely.
C
C
Fig. 15
C. Repeat this process for the two remaining
holes (C) in the dust port, stand, and dust chute.
NOTE: THE DUST CHUTE WILL ONLY BE
ATTACHED WITH THE TWO BOTTOM HOLES
(C) IN THE DUST PORT.
BAND SAW USED WITHOUT A
DUST COLLECTOR
3. If you are not going to use a dust collector with your
band saw proceed as follows:
A
A. Insert a #10-32x1/2" pan head screw through
hole (A) Fig. 16, in the stand and dust chute.
Thread a #10-32 hex nut onto the screw, and
tighten securely.
Fig. 16
B. Repeat this process for the remaining holes in
the stand. NOTE: THE DUST CHUTE WILL
ONLY BE ATTACHED WITH THE TWO
BOTTOM HOLES IN THE STAND.
STAND DOOR TO STAND
1. Align the two holes in the hinge catch (A) Fig. 17,
with the two holes on the stand. NOTE: MAKE SURE
THE HINGE CATCH (A) IS POINTED UP AS SHOWN
IN FIG. 17.
A
Fig. 17
2. Insert a #10-24x1/2" socket head cap screw
through the hole in the stand, (from the inside of the
stand), and thread the screw into the hinge catch.
Repeat this process for the remaining hole in the stand
and hinge catch. NOTE: DO NOT COMPLETELY
TIGHTEN THE SCREWS AT THIS TIME.
3. Attach the other hinge catch in the same manner.
4. Make sure the two hinge catches are aligned with
each other by using a straight edge as shown in Fig18.
5. Tighten the four screws securely, that attach the
hinge catches to the stand.
Fig. 18
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Align the two holes in the hinge (C) Fig. 19, with the
two holes in the stand door (D). MAKE SURE THAT THE
HINGE OPENING IS POINTING DOWN.
C
7. Insert a #10-24x1/2" socket head cap screw through
the hole in the door, and thread the screw into the hole
in the hinge. Repeat this process for the remaining hole
in the door and the hinge. NOTE: DO NOT
COMPLETELY TIGHTEN THE SCREWS AT THIS
TIME.
D
8. Repeat this process for the remaining hinge.
Fig. 19
9. Make sure the two hinges are aligned with each
other by using a straight edge as shown in Fig. 20.
10. Tighten the four screws securely, that attach the
hinges to the door.
Fig. 20
C
11. Slide the two hinges (C) Fig. 21, on the door, over
the two hinge catches (A) on the stand.
A
C
A
Fig. 21
12. Insert the door latch (F) Fig. 22, from the outside,
through the hole in the door.
13. Push down on the door latch to snap the latch in
place.
14. To open or shut the door, slide the latch away from
the cabinet and pull or push the door.
F
Fig. 22
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SAW TO STAND
A
THE BAND SAW IS VERY HEAVY. USE A
HELPER WHEN ATTACHING THE SAW TO THE
STAND.
1. Place the band saw on top of the stand as shown in
Fig. 23. NOTE: MAKE SURE THE PULLEY (A) FIG. 23,
IS ON THE SIDE OF THE STAND WITH THE BELT
OPENING (B).
B
C
2. Align the four holes in the saw with the four holes in
the top of the stand.
Fig. 23
3. Place a 5/16" flat washer onto a 5/16-18x1½" hex
head screw. Insert the screw through the hole (C) in the
saw and the stand.
4. Thread a 5/16-18 hex nut onto the screw.
5. Repeat this process for the three remaining holes in
the saw and the stand and tighten securely.
A
MOTOR PULLEY
D
B
1. Remove the pulley key (A) Fig. 5, that is taped to the
motor.
C
Fig. 24
2. Place the pulley key (A) Fig. 24, in the slot (B) on the
motor shaft.
3. Align the slot in the motor pulley (C) Fig. 24, with the
key (A), on the motor shaft.
4. Slide the motor pulley (C) Fig. 24, on to the motor
shaft, and tighten set screw (D) Fig. 24, on the pulley
against the key (A) on the motor shaft.
A
BELT TO SAW AND MOTOR
PULLEY
1. Place the belt over the saw pulley (A) Fig. 25.
Fig. 25
2. Lift the motor and place the other end of the belt
around the motor pulley (B) Fig. 26.
3. Check the alignment of the motor and saw pulley
with a straight edge (C) Fig. 26. Adjust the position of the
motor pulley, until the motor pulley and saw pulley are
aligned.
C
4. Push down on the motor so that there is
approximately a 1/4" deflection when pushing in on the
center of the belt.
B
5. Tighten the four bolts that hold the motor to the
motor bracket.
Fig. 26
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE TO SAW
C
1. Align the two table studs (A) Fig. 27, in the bottom of
the table, with the two holes in the trunnion assemblies
(B). Place table on trunnion assemblies. NOTE: MAKE
SURE THE SLOT (C) FIG. 27, IN THE TABLE IS
FACING AWAY FROM THE ARM (D).
D
A
A
B
B
2. Thread a 7/16" jam nut (C) Fig. 28 onto each table
stud and tighten securely.
Fig. 27
C
C
Fig. 28
3. Place the table handle (H) on each stud as shown in
Fig. 29. NOTE: MAKE SURE THE TABLE HANDLES
ARE POSITIONED AS SHOWN IN FIG. 29, SO THAT
THE TABLE CAN BE TIGHTENED AND LOOSENED.
H
H
Fig. 29
4. Thread a 7/16" locknut (D) Fig. 30, onto each stud.
Tighten each locknut up to the table handle and then
loosen each locknut a 1/2 of turn.
D
D
Fig. 30
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BLADE TO SAW
B
D
THE 14" BAND SAW USES 93½"
LENGTH BLADES.
E
1. Remove the table pin (A) Fig. 31 from the table.
2. Open the two wheel guard doors (B) Fig. 31, and the
blade guard door (C).
A
C
B
3. Make sure the quick tension lever (D) Fig. 31, is
positioned to the right of the machine, to relieve tension
as shown.
Fig. 31
4. NOTE: CHECK BLADE TO BE SURE TEETH WILL
POINT DOWN TOWARD TABLE WHEN INSTALLED.
IF NOT, TURN BLADE INSIDE OUT. Slide the band saw
blade, (teeth facing out), through the slot (E) Fig. 31, in
the band saw table.
D
5. Place the blade around the two wheel assemblies
(A) Fig. 32.
A
6. Replace the table pin (A) Fig. 31.
7. Close the two wheel guard doors (B) Fig. 31, and the
blade guard door (C).
8. Move the quick tension lever (D) Fig. 32, to the left
position to put tension on the blade as shown.
9. See the section “OPERATING CONTROLS AND
ADJUSTMENTS” to adjust blade tension and tracking.
Fig. 32
TABLE INSERT
Place table insert (A) Fig. 33, in opening of table. NOTE:
A tab (B) is provided on insert that engages with notch
(C) in table opening.
C
B
A
Fig. 33
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ON / OFF SWITCH
TO STAND
B
A
1. Remove the two outer hex nuts and lock washers (A)
Fig. 34 from the two screws extending out from the back
of the switch box (B).
A
Fig. 34
2. Insert two screws (C) Fig. 35, located on back of
switch box, into two holes (D) located in the band saw
arm.
D
C
Fig. 35
3. Use the two nuts and lockwashers (L) Fig. 36,
removed in STEP 1, to fasten the switch box to the
bandsaw arm.
4. Remove the screw and cable clamp (E) Fig. 37 from
the lower arm of the band saw.
L
5. Insert the switch cord and power cord (F) Fig. 37
into the clamp (E) (removed in STEP 4), and fasten to the
bandsaw.
Fig. 36
6. Insert the cord bushing into hole (G) Fig. 38, on the
top of the band saw stand.
F
G
E
Fig. 37
Fig. 38
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Insert the switch cord (H) Fig. 39, through the hole in
the cord bushing (G).
H
G
Fig. 39
8. Insert the pronged motor plug (J) Fig. 40, into the
receptacle (H) of switch cord.
MAKE SURE THAT THE MOTOR PLUG
(J) FIG. 40 AND THE SWITCH CORD (H)
ARE ROUTED BEHIND THE DUST
CHUTE (K). IF THE BAND SAW IS
BEING USED WITH THE ACCESSORY
HEIGHT ATTACHMENT THE THE CORD
HAS TO BE ROUTED IN FRONT OF THE
DUST CHUTE.
J
H
K
Fig. 40
OPERATING CONTROLS AND ADJUSTMENTS
STARTING AND
STOPPING SAW
The power switch is located on the left side of the
machine. To turn the machine “ON”, push the green
start button (A) Fig. 41. To turn the machine “OFF”, push
the red stop button (B).
A
B
Fig. 41
LOCKING SWITCH IN THE
“OFF” POSITION
IMPORTANT: When the tool is not in use, the switch
should be locked in the “OFF” position to prevent
unauthorized use, using a padlock (C) Fig. 42 with a
3/16" diameter shackle.
C
Fig. 42
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TILTING THE TABLE
DISCONNECT MACHINE FROM POWER
SOURCE.
D
1. The table on the band saw can be tilted 45 degrees
to the right and 8 degrees to the left. To tilt the table to
the right, loosen the two clamp handles (A) Fig. 43, tilt
the table to the desired angle as shown on the scale (D)
Figs. 43 and 44, and tighten two locking handles (A) Fig.
43.
A
A
Fig. 43
2. To tilt the table to the left, loosen the two locking
handles (A) Fig. 43, and tilt the table to the right until the
table stops (B) Fig. 44 can be accessed. Rotate the table
stop (B) Fig. 44, and tilt the table to the left. Tighten the
two locking handles (A) Fig. 43.
B
D
Fig. 44
ADJUSTING THE
TABLE STOPS
To adjust the 90 degree stop
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Loosen the table clamp handles (A) Fig. 43, and tilt
the table to the right.
B
F
2. Rotate the stop (B) Fig. 45 out of the way.
3. Place a square (G) Fig. 46, on the table and set
blade square to table.
4. Clamp table handles (A) Fig. 43.
Fig. 45
5. Rotate the stop (B) Fig. 45, until the tallest screw is
under the table skirt.
G
6. Turn the screw up or down until the screw touches
the table skirt.
7. Set pointer (J) Fig. 47 to “0” by loosening screw (K)
Fig. 47, and move pointer (J) to the “0” degree mark, and
tighten screw (K).
Fig. 46
18
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the adjustable stops:
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Loosen the two clamp handles (A) Fig. 43.
J
2. Tilt the table to the right, and turn the stop until
either stop screw (M) or (N) Fig. 48, is under the table
skirt.
K
3. Tilt the table to the left until it rests on the selected
stop screw (M) or (N) Fig. 48.
Fig. 47
4. The angle can be set by turning the stop screw and
checking the angle on the side of the scale with pointer
(J) Fig. 47.
5. Adjust the other stop screw in the same manner.
M
N
ADJUSTING BLADE
TENSION
DISCONNECT MACHINE FROM POWER
SOURCE.
Fig. 48
The band saw is equipped with a blade tension handle
(A) Fig. 49. To apply tension, move the tension handle (A)
to the left as shown. To release the blade tension, move
the tension lever lock (B) Fig. 49 up, and move the
tension handle (A) to the right as shown in Fig. 50.
A
B
To adjust the blade tension proceed as follows:
1. Push up on the blade tension lever lock (B) Fig. 49,
move the blade tension handle to the right, to remove
the blade tension.
2. The blade tension lever can be set for each of these
blade widths 3/4", 1/2", 3/8", 1/4", and 1/8".
Fig. 49
3. Make sure the blade tension lever is rotated to the
right as far as possible. Pull out on the blade tension
handle (A) Fig. 50, and turn the the tension lever until the
appropriate width of the blade is shown on the top of the
blade tension lever scale (C) and then release the blade
tension lever handle so that the handle is contacting the
hub (D).
C
A
4. Move the blade tension lever to the left until the lever
lock (B) Fig. 49 engages the blade tension lever handle
(A).
D
Fig. 50
19
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The band saw blade tension can be fined tune by
turning adjustment nut (N) Fig. 51, while the blade is
tensioned.
B
6. A series of graduations is located on the back of the
upper wheel slide bracket (T) Fig. 51. These graduations
indicate the proper tension for various widths of blades.
C
T
NOTE: THESE GRADUATIONS ARE CORRECT FOR
AVERAGE WORK, AND WILL NOT BE AFFECTED BY
REBRAZING OF THE SAW BLADE.
N
WHEN CUTTING THIN PIECES, 3/4" OR
LESS, SET THE BLADE TENSION BELOW THE
MAXIMUM SETTING FOR BLADE WIDTH, TO
EXTEND BLADE LIFE.
Fig. 51
OVER-STRAINING IS A COMMON CAUSE
OF BLADE BREAKAGE AND OTHER UNSATISFACTORY
BLADE PERFORMANCE. RELEASE THE TENSION
WHEN THE TOOL IS NOT IN USE.
A
TRACKING THE BLADE
DISCONNECT MACHINE FROM POWER
SOURCE.
BEFORE TRACKING THE BLADE,
MAKE SURE THAT THE BLADE GUIDES AND BLADE
SUPPORT BEARINGS ARE CLEAR OF THE BLADE.
After applying tension to the blade, rotate the wheels
slowly forward by hand and observe the blade’s
movement. The blade (A) Fig. 52 should travel in the
center of the upper tire. If the blade creeps toward the
front edge, loosen the wing nut (B) Fig. 51, and turn the
thumb screw (C) clockwise. This action draws the blade
toward the center of the tire. If the blade creeps toward
the back edge, turn the thumb screw in the opposite
direction. Adjust the thumb screw (C) Fig. 51 only a
fraction of a turn each time.
Fig. 52
NEVER TRACK THE BLADE WHILE
THE TOOL IS RUNNING.
After the blade is tracking in the center of the tires,
tighten the wing nut (B) Fig. 51.
VERTICAL ADJUSTMENT OF
THE UPPER BLADE GUIDE
ASSEMBLY
B
DISCONNECT MACHINE FROM POWER
SOURCE.
Adjust the blade guides and bearings according to the
following instructions.
Set the upper blade guide assembly (A) Fig. 53 as close
as possible to the top surface of the workpiece. Loosen
the lock knob (B) and move the guide assembly (A) to
the desired position.
A
Fig. 53
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE UPPER
BLADE GUIDES AND BLADE
SUPPORT BEARING
Adjust the upper blade guides and blade support
bearings ONLY AFTER the blade has the correct tension
and is tracking properly. To adjust, do the following:
DISCONNECT MACHINE FROM POWER
SOURCE
B
C
1. Make sure that the bottom blade guides and support
bearings are not touching the blade.
A
2. Check the upper blade guide assembly. The blade
guides (A) Fig. 54 should be parallel to the blade. To
adjust, loosen the screw (B) and rotate the complete
guide assembly (C). When the blade guides are parallel
with the blade, tighten the screw (B).
Fig. 54
3. Adjust the guides (A) Fig. 55 so that the front edge of
the guides are just behind the “gullets” of the saw teeth.
The complete guide block bracket can be moved in or
out by loosening the thumb screw (C) and turning the
knurled knob (D) Fig. 55. When the guides (A) are set
properly, tighten thumb screw (C).
4. Two set screws (B) Fig. 55 hold the upper blade
guides (A) in place. Loosen the set screws (B) to move
the guides (A). Place them as close as possible to the
side of the blade. (Be careful not to pinch the blade).
Tighten the screws (B).
F
5. When the blade guide wears to a point that it cannot
be adjusted close to the blade, loosen screw (B) Fig. 55
and reverse the blade guides (A) Fig. 55.
G
H
B
E
6. The upper blade support bearing (E) Fig. 55 prevents
damage to the set in the saw teeth by keeping the blade
from being pushed too far toward the back. The support
bearing (E) should be set 1/64" behind the blade by
loosening the thumb screw (F) and turning the knurled
knob (G) to move the support bearing (E) in or out.
C
D
A
B
A
Fig. 55
7. Adjust the blade support bearing (E) so that the back
edge of the blade overlaps the outside diameter of the
ball bearing by about 1/16". The bearing (E) is set on an
eccentric. To change the position, remove the screw (H)
and bearing (E) Fig. 55. Loosen the thumb screw (F),
back out the knurled knob from the set screw. Remove
the hex shaft from the hole, and rotate it to move the
eccentric for the bearing.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING LOWER BLADE
GUIDES AND BLADE SUPPORT
BEARING
B
E
A
A
B
Adjust the lower blade guides and blade support bearing
after the upper guides and bearing have been adjusted.
C
DISCONNECT MACHINE FROM POWER
SOURCE.
D
1. Adjust the front edge of the guide blocks (B) Fig. 56
so that they are just behind the “gullets” of the saw
teeth. Turn the knurled knob (C) Fig. 56 to make this
adjustment. Check the support bearing (D) Fig. 56. It
should not be touching the back of the blade.
Fig. 56
2. Loosen the two screws (A) Fig. 56. Move the guides
(B) as close as possible to the side of the blade, being
careful not to pinch the blade. Tighten screws (A).
3. Turn the other knurled knob (E) to adjust the lower
blade support bearing (D) Fig. 56 so that it is about 1/64"
behind the back of the blade.
OPERATIONS
Before starting the machine, insure that all adjustments are properly made and the guards are in place. Turn the upper
wheel by hand to make sure that everything is correct BEFORE turning on the power.
Keep the top blade guide (and guard) within 1/8" of the work piece at all times. Do not force the material
against the blade. Light pressure on the work piece will produce a smoother cut, and prevent excess friction, and
heating of the blade.
KEEP THE SAW BLADE SHARP. Very little forward pressure is required for normal cutting. Keep the workpiece
moving at a slow and consistent rate against the blade to ensure a smooth and accurate cut.
Avoid twisting the blade, by trying not to turn sharp corners. Remember, you must saw around corners.
CUTTING CURVES
When cutting curves, turn the stock carefully so that the blade follows without twisting. If a curve is so abrupt that it is
necessary to repeatedly back up and cut a new kerf, a narrower blade, a blade with more set, or additional relief cuts
Fig. 57, may be necessary to allow the blade to cut more efficiently. The more set a blade has, the easier it will allow
the stock to be turned, but the cut is usually rougher.
When withdrawing the piece being cut, changing the cut, or for any other reason, be careful not to accidentally draw
the blade off the wheels. In most cases, it is easier and safer to turn the stock and saw out through the waste material,
rather than try to withdraw the stock from the blade.
Fig. 57
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
In spite of how well a band saw is maintained, problems can occur. The following troubleshooting
guide will help you solve the more common problems:
Trouble: SAW WILL NOT START.
Probable Cause
Remedy
1. Switch cord / motor cord not plugged in.
2. Fuse blown or motor reset tripped.
3. Cord damaged.
1. Plug in switch cord / motor cord.
2. Replace fuse or push motor reset button.
3. Have cord replaced.
Trouble: BREAKER OR MOTOR KICKS OUT FREQUENTLY.
Probable Cause
Remedy
1. Extension cord too light or too long.
2. Feeding stock too fast.
1. Replace with adequate size cord.
2. Feed stock more slowly.
3. Clean or replace blade.
4. Contact an electrician.
3. Blade in poor condition (dull, warped, gummed).
4. Low voltage supply.
Trouble: BAND SAW VIBRATES EXCESSIVELY.
Probable Cause
Remedy
1. Machine not mounted securely to stand.
2. Stand on uneven surface.
3. Worn belt.
1. Tighten all mounting hardware.
2. Reposition on flat level surface.
3. Replace belt.
4. Pulley not aligned.
4. Adjust motor pulley.
5. Tighten all mounting hardware.
5. Motor not fastened securely.
Trouble: BAND SAW DOES NOT COME UP TO SPEED.
Probable Cause
Remedy
1. Low voltage due to improper extension cord size.
2. Low voltage.
1. Replace with adequate size cord.
2. Contact an electrician.
3. Rewire motor for correct voltage.
3. Motor wired for incorrect voltage.
Trouble: BLADES BREAK.
Probable Cause
Remedy
1. Blade not tensioned properly.
2. Blade guides improperly adjusted.
3. Blade support bearing improperly adjusted.
4. Blade wheel tracking adjustment improperly set.
5. Bad weld on blade.
1. Adjust blade tension.
2. Check and adjust blade guides.
3. Adjust blade support bearing.
4. Check and adjust blade tracking.
5. Replace the blade.
6. Worn tires.
6. Replace tires.
7. Forcing wide blade around short radius.
8. Dull blade or insufficient set.
9. Upper blade guide set too high.
7. Change to a narrower blade.
8. Replace blade.
9. Set upper blade guide within 1/8" of workpiece.
10. Continuous running of machine when not actually
cutting.
10. Turn off machine when not performing cutting
operation.
(continued on next page)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble: BLADE WILL NOT TRACK.
Probable Cause
Remedy
1. Blade too loose
1. Adjust tension
2. Upper wheel not properly adjusted.
3. Improperly adjusted blade support bearing.
2. Adjust upper wheel.
3. Adjust blade support bearing.
Trouble: CUT DOES NOT AGREE WITH SETTING ON THE TILT SCALE.
Probable Cause
Remedy
1. Pointer out of adjustment
1. Adjust pointer.
Trouble: BLADE WILL NOT STAY ON WHEEL.
Probable Cause
Remedy
1. Blade not tensioned properly.
2. Blade guides improperly adjusted.
3. Blade support bearing improperly adjusted.
4. Blade wheel not tracking properly.
5. Bad weld on blade.
1. Adjust blade tension.
2. Check and adjust blade guides.
3. Adjust blade support bearing.
4. Check and adjust blade tracking.
5. Replace the blade.
6. Worn tires.
6. Replace tires.
Trouble: BAND SAW MAKES UNSATISFACTORY CUTS.
Probable Cause
Remedy
1. Blade not tensioned properly.
2. Blade guides improperly adjusted.
3. Blade support bearing improperly set.
4. Blade wheel not tracking properly.
5. Bad weld on blade.
1. Adjust blade tension.
2. Check and adjust blade guides.
3. Adjust blade support bearing.
4. Check and adjust blade tracking.
5. Replace the blade.
6. Worn tires.
6. Replace tires.
7. Incorrect blade for work being done.
8. Dull blade or insufficient set.
9. Upper blade guide set too high.
7. Change the blade.
8. Replace blade.
9. Set upper blade guide within 1/8" of work piece.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
BAND SAW BLADES
A band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can
obtain long use from a band saw blade if you use it properly. Be sure you use blades of the proper
thickness, width and temper for the various types of material and cuts.
Always use the widest blade possible. Use narrow blades only for sawing small, abrupt curves
and for fine, delicate work. This will save blades and will produce better cuts. For cutting wood
and similar materials, Delta offers blades in widths of 1/8", 1/4", 3/8", 1/2", and 3/4".
Any one of a number of conditions may cause a band saw blade to break. Blade breakage is, in
some cases, unavoidable, being the natural result of the peculiar stresses to which blades are
subjected. Blades will break often due to avoidable causes, such as the lack of care to the blade
or the blade not being properly adjusted to the band saw. The most common causes of blade
breakage are:
(1) faulty alignments and adjustments of the guides.
(2) forcing or twisting a wide blade around a curve of short radius.
(3) feeding the work piece too fast into the blade.
(4) dullness of the teeth, or absence of sufficient set.
(5) improperly tensioned blade.
(6) top guide set too high above the work piece being cut.
(7) using a blade with a lumpy or improperly finished braze or weld.
(8) continuous running of the saw blade when not cutting.
Use blades that are 93½" in length on this machine.
Always use a sharp blade. Keep it free from gum and pitch. Clean frequently with a stiff fiber
brush.
Narrow blades are used for cutting small circles or curves while the wider blades are best suited
for straight cutting such as ripping.
A new blade, in most cases, will perform better and last longer than a re-sharpened blade.
Insure that the blade guides are adjusted properly.
Do not force or twist the blade around a curve or a very short radius.
Feed the workpiece through the blade at a consistent rate, allow the blade to do the cutting – do
not feed the work piece too fast.
Do not apply excessive tension to the blade. The tension is only necessary to drive the blade
without slipping on the wheels. Narrow blades require less tension than wider blades.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or
for the name of your nearest supplier.
Since accessories other than those offered by Delta have not been tested with this
product, use of such accessories could be hazardous. For safest operation, only Delta
recommended accessories should be used with this product.
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted
defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by
anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for
incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether
of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta Machinery are Available at These Locations
•
Delta)
Cleveland 44125
ARIZONA
MINNESOTA
ILLINOIS
Minneapolis 55429
8001 Sweet Valley Drive
Unit #19
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
Phone: (216) 447-9030
Fax: (216) 447-3097
Phone: (602) 437-1200
Fax: (602) 437-2200
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MISSOURI
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
MARYLAND
St. Louis 63119
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
COLORADO
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
Houston 77055
Phone: (954) 321-6635
Fax: (954) 321-6638
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
OHIO
WASHINGTON
MICHIGAN
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Fax: (248) 597-5004
Phone: (404) 608-0006
Fax: (404) 608-1123
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
QUÉBEC
MANITOBA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1515 ave.
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
1447, Begin
505 Southgate Drive
Guelph, Ontario
N1H 6M7
St-Laurent, (Montréal),
Québec
V5A 4T8
H4R 1V8
Phone: (519) 836-2840
Fax: (519) 767-4131
Phone: (604) 420-0102
Fax: (604) 420-3522
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE·
DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,
BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series
2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®,
JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET
CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®,
Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-
LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®,
STAIR EASE®, The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL
SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®,
UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER
SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other
countries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y
también pueden estar registradas en otros países.
Printed in U.S.A.
PC-0403-149
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Philips Flat Panel Television 14PT1345 58 User Manual
Philips Flat Panel Television PFL5XX7H 12 User Manual
Philips Food Warmer SCF615 10 User Manual
Philips Fryer HD6105 User Manual
Philips TV Cables SWA2510 User Manual
Philips Washer SBD6000 User Manual
Pioneer CD Player DEH P250 User Manual
Polycom Wireless Office Headset VVX 500 User Manual
Porter Cable Air Compressor C7501 User Manual
Poulan Chainsaw 1980 02 User Manual