J693
Operator’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright Information:
CG Triumvirate is a trademark of Agfa Corporation.
CG Times based upon Times New Roman under license from the Monotype Corporation.
Firmware (Software) Agreement
The enclosed Firmware (Software) resident in the Printer is owned by Licensor or its
suppliers and is licensed for used only on a single printer in the user’s Trade or Business.
The User agrees not to, and not to authorize or permit any other person or party to
duplicate, or copy the Firmware or the information contained in the non-volatile or
programmable memory. The firmware (Software) is protected by applicable copyright
laws and Licensor retains all rights not expressly granted. In no event will Licensor or its
suppliers be liable for any damages or loss, including direct, incidental, economic,
special, or consequential damages, arising out of the use or inability to use the Firmware
(Software).
Information in this document is subject to change without notice and does not represent a
commitment on the part of Pitney Bowes. No part of this manual may be reproduced or
transmitted in any form or by any means, for any purpose other than the purchaser's
personal use, without the expressed written permission of Pitney Bowes.
All rights reserved. Printed in the United States of America.
Part Number: 88-2271-01
J693 - SV60824
Revision: B
Download from Www.Somanuals.com. All Manuals Search And Download.
Agency Compliance and Approvals:
UL1950 Information Technology Equipment
C22.2 No. 950-M93
C
US
Listed
EN60950
For 230 Volt Operation (Europe): Use a cord set, marked "HAR," consisting
of a min H05VV-F cord which has a minimum 0.75 square mm diameter
conductors, provided with an IEC 320 receptacle and a male plug for the
country of installation rated 6A, 250V
Für 230 Volt (Europa): Benützen Sie ein Kabel, das mit "HAR" markiert ist,
bestehend mindestens aus einem H05VV-F Kabel, das mindestens 0,75
Quadratmillimeter Drahtdurchmesser hat; sowie eine IEC320 Steckdose und
einen für das Land geeigneten Stecker, 6A, 250 Volt.
As an Energy Star Partner, the manufacturer has determined that this product
meets the Energy Star guidelines for energy efficiency.
The manufacturer declares under sole responsibility that this product conforms
to the following standards or other normative documents:
EMC: EN 55022 (1993) Class B
EN 50024 (1998)
EN 45501 (1992)
Safety: This product complies with the requirements of EN 60950/All:1997
Gost-R
FCC: This device complies with FCC CFR 47 Part 15 Class A.
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions in this manual, it may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions:
This printer has been carefully designed to give you many years of safe, reliable
performance. As with all electrical equipment, there are some basic precautions
you should take to avoid hurting yourself or damaging the printer:
Before using the printer, carefully read all the installation and operating
instructions.
Observe all warning instruction labels on the printer.
Install the printer on a flat, firm, solid surface.
To protect your printer from overheating, make sure all openings on the
printer are not blocked.
Do not place the printer on or near a heat source.
Do not use your printer near water, or spill liquid into it.
Ensure that your power source matches the rating listed of your printer. If
unsure, check with your dealer or local Utility provider.
Do not place the power cord where it will be stepped on. If the power cord
becomes damaged or frayed, replace it immediately.
Do not insert anything into the ventilation slots and openings on the printer.
Use a qualified, trained service technician should the printer ever need repair.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Overview
1.0 About this Printer...............................................................1
1.0.1 Standard Features .................................................2
Getting Started
2.0 Inspection...........................................................................3
Setting Up the Printer
3.0 Installing the Printer ..........................................................5
3.0.1 Communications Interfacing................................6
3.1 Loading Media...................................................................7
3.3 Loading Ribbon ...............................................................10
Using the Front Panel
4.0 Operating the Front Panel................................................13
4.0.1 Ready Mode: Normal Operation........................13
4.0.2 Menu Mode: Configuration................................14
4.0.3 Quick Test Mode: Print Test Labels ..................15
4.0.4 Indicator Lights ..................................................16
4.0.5 LCD (Display)....................................................16
4.0.6 Resetting the Printer...........................................17
4.1 Navigating the Menu System...........................................18
4.1.1 Media Settings....................................................20
4.1.2 Print Control.......................................................21
4.1.3 Printer Options ...................................................22
4.1.4 System Settings ..................................................24
4.1.5 Communications ................................................28
4.1.6 Diagnostics.........................................................30
4.2 Understanding the Display Messages..............................31
4.2.1 The User Prompts and Condition Messages ......31
i
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Printing from the Quick Test Mode.................................34
4.3.1 Print Quality Label.............................................34
4.3.2 Configuration Label ...........................................35
4.3.3 Quick Ribbon Test Label ...................................36
4.3.4 Dot Test Pattern Label........................................37
4.3.5 Validation Label.................................................38
4.3.6 User Defined Label ............................................38
Adjusting and Maintaining the Printer
5.0 Media Sensor Adjustment................................................39
5.1 Positioning Calibration....................................................41
5.2 Media Sensor Calibration ................................................41
5.2.1 Standard Calibration...........................................41
5.2.2 Advanced Entry Calibration...............................47
5.3 Printhead Adjustments.....................................................53
5.3.1 Burn Line Adjustment........................................53
5.4 Printhead Replacement ....................................................55
5.5 Cleaning Schedule ...........................................................56
5.5.1 Cleaning the Printhead .......................................57
5.5.2 Cleaning the Platen Roller..................................58
5.5.3 Cleaning Interior and Exterior Surfaces.............59
5.6 Updating the Application Program..................................59
5.6.1 Updating from the Ready Mode.........................60
5.6.2 Updating from the Download Mode ..................61
5.6.3 Application Update Problems ............................62
5.7 Updating the Boot Loader Program.................................63
Troubleshooting
6.0 Troubleshooting Tips.......................................................65
6.1 Fault and Warning Messages...........................................69
6.2 Hex Dump Mode .............................................................74
Specifications
7.0 Printer Specifications.......................................................75
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
ASCII Control Code Chart......................................................77
Appendix B
Available Fonts and Bar Codes...............................................79
Appendix C
Module Assignments...............................................................87
Print Resolutions and Maximum Widths ................................87
Speed Settings and Defaults....................................................88
Appendix D
Menu System Multi-Language Support..................................89
Glossary of Terms
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
1.0 About this Printer
Congratulations on your purchase of a new J693 printer. The J693, hereafter
referred to as ‘the printer’, blends the rugged durability of cast-frame
construction with other innovative design features to redefine the standard in
industrial thermal printers.
The printer incorporates highly specialized
electronics, including a powerful
32-bit processor and up to 8
megabytes of on-board
memory. Control and program
changes can be made smoothly,
with most functions accessible
through either the front panel
or labeling software program.
The user-friendly printing
concept is taken a step further
with its quick-load media
design, easily added application
upgrades, and modularly installed
options.
This manual provides all the information necessary to operate the printer on a
daily basis. To print labels or tags simply refer to the instructions included with
the software you have chosen to create the labels. If you wish to write a custom
program, a copy of the Programmer’s Manual is included on the Accessories
CD.
To meet all of your printing needs this unit is easily configurable. The following
subsections list the standard and optional features, including the requirements to
upgrade the printer.
J693
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0.1
Standard Features
To meet all of your printing needs this unit is easily configurable. This section
lists the available standard and optional hardware features.
This printer offers the following standard features:
Printing
203 Dots Per Inch
Thermal Transfer Printing
On-Demand and Batch Printing
Rotating Label Hub
Simple Label Loading
Label Tear Bar
Peel and Present Mechanism
Internal Label Rewinder
Interfaces
RS-232 Serial Interface
IEEE 1284 Compliant Parallel Interface
Memory
1MB Flash Programmable Downloadable Memory
8MB SDRAM
Operational
2 X 20 Character, Liquid Crystal Display (LCD)
EFIGS (English, French, Italian, German, and Spanish) display
languages
AGFA Scalable font engine with CG Triumvirate Scaleable and CG
Triumvirate Bold Condensed Font
Printhead Resistance Verification
2
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
2.0 Inspection
After removing the printer from the packaging material, check the contents of
the package. In addition to this manual, the following items should be included:
Printer
Power Cord
Accessories CD
Serial or interface cable
Label roll
Rewinder Clasp
J693
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ
3.0 Installing the Printer
This section explains how to connect and load the printer with media and
ribbon.
Note: When connecting the AC Power Cord or data cables to the printer,
ensure the Power On/Off Switch is in the ‘Off’ position.
Connect the AC power cord to the receptacle located on the back of the printer,
then plug the cord into a properly grounded outlet.
J693
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0.1 Communications Interfacing
Using a data detection process, the interface selection occurs automatically in
the printer. At power-up, the printer begins monitoring the interface ports for
activity. When the host transmits data, the printer port detecting this data is set
‘active’ and remains active as long as data flow continues. Once the received
data flow stops and the Host Timeout Value (see Section 4.1.5) is exceeded, the
detection process will be repeated; in addition, should the data flow stop before
a complete label format is received, the format will be ignored and must be sent
to the printer again.
Note: To change an active port immediately, cycle the printer power ‘On’
and ‘Off’.
Serial Port:
The serial port interface supports RS-232C and, if equipped, RS-422
communications. The following list of printer serial port settings are menu
selectable and must be set to match the host computer serial port settings; see
Section 4.1.5.
•
•
•
•
•
Baud Rate (communication speed)
Word Length
Word Parity
Number of Stop Bits
Handshaking Protocol
In addition to these settings, the serial interface cable must a have specific pin
configuration (pin-out) for proper data exchange (contact your salesperson for
ordering information).
6
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Loading Media
The following procedures explain the preliminary label loading steps.
Raise the Access Cover.
Rotate the Printhead Latch
forward to raise the printhead.
Slide the Label Guide out away from the frame and then lower it to the
down position.
Note: In this left-justified printer, always place the labels against the
backstop when loading.
Pull outward on the Roller Bracket and allow it to swing down.
Load labels and advance approximately 20 inches of labels from the front
of the printer. Remove the labels from the entire length, leaving only the
backing material.
J693
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Route the backing material through the Roller Bracket as shown. Then
raise the Roller Bracket up to its latched position.
8
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Route the Label Backing back to, and around the Rewind Hub, as shown.
Insert the leading edge of the Label Backing into the Slot on the Rewind
Hub and then insert the Label Retainer into the Slot on the Rewind Hub.
Rotate the Rewind Hub to remove the slack in the Label Backing. Be sure
the printhead latch is down and in the locked position.
)
After finishing, close the Access Cover and then push and hold the FEED
key for four seconds to secure the backing material and calibrate the label
TOF.
Label Backing Removal:
Grasp the used backing on the Rewind Hub, and while gently pulling out on
the hub, compress the hub and pull off the backing.
J693
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Loading Ribbon
Note: Always use ribbon slightly wider than the label backing material;
this helps protect against printhead wear. Use only Pitney Bowes
ribbons and labels.
To produce an image on the label, thermal transfer labels requires ribbon.
Ribbon types are available with the ‘ink’ layer on the outside (coating side out)
or with the ‘ink’ layer on the inside (coating side in). These types cannot be
interchanged in the printer. Arrows on the Ribbon Supply Hub are used to
indicate the correct direction of ribbon travel (see the next page for examples).
To load a ribbon:
Raise the Access Cover.
Rotate the Printhead Latch
forward to raise the printhead.
10
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Mount the ribbon so that it is dispensed in the appropriate direction for the
ribbon type.
Slide the ribbon on completely to rest against the flange.
Route the ribbon under the Ribbon Roller then out the front of the printer.
Continue routing the ribbon up to and around the Ribbon Take-Up Hub, as
shown. Wind the ribbon around several times in a clockwise direction to
secure it in place.
Lower the printhead and rotate the Printhead Latch back to the locked
position. Close the Access Cover.
With the printer ‘On’ press and hold the FEED button for three seconds to
position the labels for printing; see Section 5.2 for details.
Ribbon routing path
Ribbon Removal:
Pull the empty core from the Ribbon Supply Hub and discard it. Next, grasp
the used ribbon on the Ribbon Take-Up Hub, while gently pulling out on the
hub, compress the hub to pull off the used ribbon.
J693
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢃ
4.0 Operating the Front Panel
The front panel is equipped with five keys, 3 indicator lights and a Liquid
Crystal Display (LCD). The key functions differ depending upon the selected
mode of the printer. The selectable modes are Ready, Menu and Quick Test.
4.0.1
Ready Mode: Normal Operation (Ready Light ‘On’)
The PAUSE key temporarily suspends printing.
Pressing again returns the printer to normal
operation.
The FEED key advances one label, and clears any
corrected faults.
Pressing and holding for 4 seconds will reset the
expected label length for gap and reflective modes.
The CANCEL key ‘pauses’ the printer and then
prompts for confirmation. If yes, the current job is
cancelled. The printer remains paused.
Pressing and holding for 4 seconds will reset the
printer and clear temporary host settings (soft
reset).
The MENU key toggles between the Ready and
Menu Modes.
In the Ready mode, pressing and holding 4 seconds
will change the display contrast.
The TEST key enters (or exits) the Quick Test
Menu.
J693
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0.2
Menu Mode: Configuration (Ready Light ‘Flashing’)
The DOWN ARROW key scrolls to the previous
menu item on the same menu level. It also,
decrements numerical values in most menu
selections.
The UP ARROW key scrolls to the next menu
item. It also increments numerical values in most
menu selections.
The ENTER key selects the function or displayed
value (selection is indicated with an ‘*’ or ‘ ’ for
bootables which require
a
reset to become
effective). It also moves between selections in
multiple parameter fields.
The ESCAPE key moves to the previous menu
level, and finally back to the READY mode.
14
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0.3
Quick Test Mode: Print Test Labels
The DOWN ARROW key scrolls to the previous
test function.
The UP ARROW key scrolls to the next test
function.
The ENTER key will change the selected test
label quantity of 2, 100, 1000, or 9999 (except the
‘Configuration Label’, this quantity is always
one). Holding down the key scrolls quantities.
The ESCAPE key will exit the Quick Test Mode
without printing.
The TEST key will print the selected test label at
the selected quantity.
During test label printing, this key can also
perform as a cancel key (the printer will prompt
for confirmation before cancellation occurs).
Notes: The test functions are disabled while processing data from
communications interfaces until the Host Timeout value expires.
J693
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0.4
Indicator Lights
‘On’ indicates READY Mode.
‘Slow Flashing’ indicates Menu Mode.
‘Fast Flashing’ indicates data is being received
and processed.
‘On’ indicates a ‘Paused’ state.
‘Slow Flashing’ indicates a Warning.
‘Fast Flashing’ indicates a Fault.
See Section 6.1 for a list of the display messages.
4.0.5
LCD (Display)
Liquid Crystal Display
The display provides several types of information:
• Following a brief power-up sequence, the
READY message.
• The time and date, if the printer has received it
from one of the following: the host, the front
panel setting, or the Time and Date option.
• A label counter during a batch print job.
• Any prompt, condition, downloading, warning,
or fault message.
• The Menu System when in the Menu Mode.
16
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0.6
Resetting the Printer
Depending upon the method used, there are three reset levels possible:
4.0.6.1
Soft Reset
To reset the printer and clear any temporary host settings:
With the printer ‘On’, press and hold the CANCEL key for approximately
four seconds.
4.0.6.2
Level 1 Reset
To return the printer to the factory default settings:
Turn ‘Off’ the printer.
Press and hold the PAUSE and CANCEL keys while turning ‘On’ the
printer; continue to depress the keys until the ‘SYSTEM RESET’ message
flashes.
Note: This reset can also be executed using the menu system: System
Settings/Set Factory Defaults. See Section 4.1 for a listing of the
factory default settings.
4.0.6.3
Level 2 Reset
To return the printer to the factory default settings, and clear all the calibration
and adjustment parameters:
Turn ‘Off’ the printer.
Press and hold the PAUSE, FEED, and CANCEL keys while turning ‘On’
the printer; continue to depress the keys until the ‘SYSTEM RESET’
message flashes.
Note: After executing a Level 2 Reset, both Ribbon and Media
Calibrations must be performed; see Sections 5.1 and 5.2. See
Section 4.1 for a listing of the factory default settings.
J693
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Navigating the Menu System
Printer operation can be controlled through the user interface, allowing the
operator access to these six menu system branches:
•
•
•
•
•
•
Media Settings
Print Control
Printer Options
System Settings
Communications
Diagnostics
While in the menu system, the current selection will be indicated with the ‘*’
symbol next to the displayed item on the LCD, and selections designated with
the ‘§’ symbol will require a printer reset before becoming effective. Changes
made can be saved so that, in the event that power is lost or removed, the new
settings will be retained. A reset will be automatically invoked when exiting the
menu system and answering ‘Yes’ to the ‘Save Changes’ prompt.
The same functional commands from the host computer may, in some cases,
override the printer’s menu settings. In addition, as a security feature for the
prevention of accidental or unauthorized changes, the menu system has a
password protection feature.
Note: In the following subsections, the factory default settings are denoted
with the ‘ ’ symbol. Selections denoted with the ‘♦’ symbol can only
be changed through the menu system - all other selections can be
overridden by host software commands. Consult the Programmer’s
Manual for specific information.
(Continued next page)
18
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
From Ready Mode, press the
key to enter the Menu Mode. Depending
upon the configuration of the printer, the following is a list of the possible Enter
and Exit Prompts.
MENU MODE
Enter/Exit Prompt Description:
You are attempting to enter the Menu Mode.
Security has been enabled and now the
correct user-definable password is required
for access the Menu Mode functions.
ENTER PASSWORD
0 0 0 0
You are now entering the Menu Mode. Host
commands have affected the configuration
of the printer. Pressing ENTER will save
these changes; otherwise, the printer will
revert to previously saved settings.
KEEP HOST CHANGES?
ENTER = YES
You are now exiting the Menu Mode, but
have made changes to the printer’s settings.
Pressing ENTER will reconfigure your
printer according to these changes;
otherwise, the printer will revert to
previously saved settings.
SAVE CHANGES?
ENTER = YES
Note: While in the Menu Mode, the printer will stop processing new DPL
(or bitmapped) data.
J693
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.1
Media Settings
MEDIA TYPE
DIRECT THERMAL
THERMAL TRANSFER
Selects a print method.
For use with heat sensitive media.
For use with media requiring a ribbon to
create an image.
SENSOR TYPE
Selects the top-of-form (TOF) sensing
method for the media.
The printer recognizes the TOF by sensing
gaps in the media.
GAP
No TOF sensing. The user must use the
LABEL LENGTH setting to determine TOF.
The printer recognizes the TOF by sensing
reflective (black) marks on the underside of
media.
CONTINUOUS
REFLECTIVE
LABEL LENGTH
04.00in (0-99.99)
For use with continuous media. Label length
is used to determine the TOF when ‘Sensor
Type-Continuous’ is selected.
MAXIMUM LABEL LENGTH Sets the maximum length between TOF
16.00in (0-99.99)
marks (gap or black stripe). If this limit is
exceeded, a top of form fault is declared.
Adjusts the printer to sense your media.
SENSOR CALIBRATION ♦
The user follows steps to allow the printer to
calculate the empty, gap or mark, and paper
values to set the media sensor.
PERFORM CALIBRATION
Note: Firmware versions 3.04 and
greater – After successful completion,
these parameters are automatically stored
for future sessions.
The user directly inputs the best values to
adjust the media sensor.
Sets threshold values for the media sensor
parameters. Entry for paper, gap/mark, and
empty thresholds.
ADVANCED ENTRY
SENSOR LEVELS
SENSOR GAIN
Observe A/D reading and set SENSOR
GAIN. Adjusts the sensitivity of the sensor
for custom label stock.
20
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.2
Print Control
HEAT
10 (0-30)
Controls the printhead ‘burn-time’; see Section
2.1.1 for more on print quality control.
PRINT SPEED
FEED SPEED
Controls the rate of label movement during the
printing process; see Appendix C.
Controls the rate of label movement between
printing areas; see Appendix C.
REVERSE SPEED
Controls the rate of label movement during
backup positioning for start of print, cutting or
present distance; see Appendix C.
ROW OFFSET
00.00in (0-99.99)
Shifts the vertical start of print position. This is
the user setting for row adjustment.
COLUMN OFFSET
00.00 in (0-99.99)
Shifts the horizontal, left-justified start of print
position to the right. Does not shift label width.
LABEL WIDTH
Sets the maximum limit for the printable surface
width. Images or data beyond this limit will not
print; see Appendix C.
PRESENT DISTANCE
0.72 in (0-4.00)
Specifies an additional amount to advance the
label after printing. When the next label format
is received, the printer backfeeds to the start
position. Only the last label of the batch will be
presented if the present sensor is not enabled.
CUSTOM ADJUSTMENTS These factory adjustments independently
change listed parameters, compensating for
slight mechanical differences sometimes evident
when multiple printers share the label formats.
Controls the printhead strobe time to fine-tune
the HEAT setting.
♦
DARKNESS
XX
(1-64)
Shifts the vertical start of print position
upward in dots to fine-tune the ROW OFFSET
setting; see Appendix C.
ROW ADJUST
XXX DOTS (0-128)
Note: A Positioning Calibration must be
performed before this parameter takes effect;
see Section 5.1.
Shifts both the horizontal start of print position
and the LABEL WIDTH termination point to
the right in dots to fine-tune the COLUMN
OFFSET setting; see Appendix C.
COLUMN ADJUST
XXX DOTS (0-128)
Adjusts the label stopping position in dots to
fine-tune the PRESENT DISTANCE setting;
see Appendix C.
PRESENT ADJUST
XXX DOTS (0-128)
J693
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.3
Printer Options
MODULES
The physical presence of the respective memory
module must be detected to show the module
function selections for that module in the menu
system.
Prints a label directory of all available
modules, the available space on these modules,
the files present, and the type of module and
files.
PRINT DIRECTORY
The user may select from a list of available
files for sample printing.
PRINT FILE
The user may select from a list of available
modules for formatting – all data will be
erased.
FORMAT MODULE
The user may select from a list of available
files for deleting. Bytes will NOT be retrieved
until the module that contained the deleted file
is packed.
DELETE FILE
Packing the module removes files marked as
deleted and defragments existing file structures
to recover space.
PACK MODULE
PRESENT SENSOR
Used for on-demand label dispensing, where a
printed label blocking the sensor will inhibit
further printing until removed. The physical
presence of the Present Sensor must be
detected to show the ENABLE/DISABLE
selections in the menu system.
Enables the sensor for on-demand printing.
Disables the sensor.
ENABLED
DISABLED
No sensor is detected.
NOT INSTALLED
CUTTER
Physical presence of a cutter must be detected
to show the ENABLE/DISABLE selections in
the menu system.
Enables the cutter for label cutting.
Disables the cutter.
ENABLED
DISABLED
No cutter is detected.
NOT INSTALLED
(Continued next page)
22
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Options (continued)
GPIO PORT
The physical presence of the optional GPIO
port must be detected to show the selections in
the menu system.
Instructs the printer to update the output
GPIO
signals and to wait for the Start of Print Signal
to print a label.
ENABLED
DISABLED
Yes
No
Defines the operation of the printer’s End of
Print signal as sent to the applicator. This
signal indicates that the printer has completed
the print cycle.
END OF PRINT
LOW STATUS
HIGH STATUS
LOW PULSE
A steady Low (0 VDC) during the print cycle.
A steady High (5 VDC) during the print cycle.
A Low Pulse (0 VDC for 30 ms) at the end of
print.
HIGH PULSE
DISABLED
A High Pulse (5 VDC for 30 ms) at the end of
print.
No indication.
J693
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.4
System Settings
INTERNAL MODULE
1024 KB
Sets the number of 1K blocks allocated for
the internal RAM ‘D’ module. Available
memory dependent upon model; see
Appendix C.
DEFAULT MODULE
D
Sets the default module used to store files
when no module is specified; see Appendix C.
SCALEABLE FONT
CACHE
0312 KB
Sets the number of 1K blocks allocated for
the scaleable font engine. Available memory
dependent upon model; see Appendix C.
SYMBOL SET
Selects the code page used to print single
byte fonts unless otherwise specified in DPL,
see the Programmer’s Manual.
61 selectable sets, see the Programmer’s
Manual.
PC_850
MULTILINGUAL
TIME AND DATE
Allows the user to set Time and Date.
MEDIA COUNTERS
Internal record of inches printed and time in
use.
Shows the number of inches printed and
number of hours the printer has been
powered ‘On’ since being set at the factory.
Not resettable by the user.
ABSOLUTE COUNTER
The number of operational hours and inches
printed from the date last reset. User may
reset.
RESETTABLE
COUNTER
Resets the resettable counters to zero.
RESET COUNTER
PRINT CONFIGURATION Prints the effective configuration of the
system. In addition, if settings were changed
that require a reset to become effective, this
will be indicated with the ‘§’ symbol.
A ‘•’ symbol next to the printed item
indicates that it was changed via the host but
not saved in non-volatile memory.
(Continued next page)
24
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
System Settings (continued)
CONFIGURATION LEVEL
To upgrade the application (resident
software) of the printer, the hardware and
software compatibility levels must match for
the update to be accepted. This information is
displayed here and can also be found printed
on the configuration label.
Each printer has a unique KEY number in the
following form:
PRINTER KEY
vvvv-wwxx-yyyyyy-zzz
where:
vvvv – represents the model number of the
application loaded
wwxx – represents the configuration level
ww represents the main board
hardware compatibility
level
xx represents the software
compatibility level (see
below)
yyyyyy – is a manufacturing date code
zzz – is a unique time stamp
The application version may only be updated
with a configuration level of equal or lesser
value than the software level; however, the
printer’s software compatibility level can be
increased by purchasing and entering the
proper upgrade code here.
UPGRADE PRINTER
CODE
(Continued next page)
J693
25
Download from Www.Somanuals.com. All Manuals Search And Download.
System Settings (continued)
SET FACTORY DEFAULTS Parameters in this menu listing with the ‘
’
symbol are the designated defaults.
Overwrite the current settings with the
factory default settings.
SET FACTORY
DEFAULTS
Note:
The
printer
will
reset
automatically. All menu settings will be
restored except CUSTOM ADJUSTMENTS
and the media and ribbon calibration
parameters.
FORMAT ATTRIBUTES
Affects the manner in which overlapping
text and graphics are treated as the label is
printed. Consult the Programmer’s Manual
for details.
Intersecting text strings, images, and bar
codes will not be printed. (An odd number
of overlapping objects will print.)
TRANSPARENT
Intersecting text strings, images, and bar
codes print on top of one another.
XOR
Interacting text strings, images, and bar
codes are obliterated by those formatted
last. Each character cell is treated as
opaque.
OPAQUE
Instructs the printer whether it can pre-
image the label format.
IMAGING MODE ♦
Note: This selection can affect the
accuracy of time-stamped labels and label
throughput.
The printer images multiple labels as
memory permits, achieving the fastest
throughput; however if time-stamping, the
time will reflect the moment the label is
imaged rather than when actually printed.
The printer images the next label only after
the previous label has been successfully
printed; this single processing provides
more accurate time-stamps with a minor
cost to label throughput.
MULTIPLE LABEL
SINGLE LABEL
(Continued next page)
26
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
System Settings (continued)
PAUSE MODE
When enabled, PAUSE MODE suspends
printing between each label until the
PAUSE key is pressed.
Printer requires operator to press the
PAUSE key after each label.
Printer completes label batch without
pausing between labels.
ENABLED
DISABLED
Provides the user with the ability to
password protect all printer settings made
through the operator panel.
Enable or disable the menu system’s
security feature.
SECURITY ♦
SELECT SECURITY
ENABLED
DISABLED
Password protected.
No protection.
Modify the password required to access the
menu system when security is enabled.
MODIFY PASSWORD
UNITS OF MEASURE
Selects the measurement system in which
the system’s settings are represented in the
menu system and on configuration labels.
Metric standard: Lengths in millimeters;
Counters in centimeters.
METRIC
Inch standard: Lengths and Counters in
inches.
IMPERIAL
DPI EMULATION
Allows users to print files intended for a
Prodigy Plus® and Allegro® printers.
Formats emulated for 200 DPI printing.
Standard 203 DPI printing.
200 DOTS PER INCH
203 DOTS PER INCH
ALLEGRO EMULATION
Allows users to print files intended for an
Allegro® printer.
Row calculation is reduced to 195 DPI,
shrinking the label length.
ENABLED
Standard 203 DPI formatting.
DISABLED
Selects the language in which the menu
system messages and configuration label
are shown. Only languages that are resident
will be available.
MENU LANGUAGE ♦
English
ENGLISH
…
User defined, downloaded language(s).
J693
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.5
Communications
Controls Serial Port A communications
settings.
SERIAL PORT A♦
Determines the serial communication rate.
BAUD RATE
38400
28800
19200
9600
9600 bits per second
4800
2400
Sets the flow control (handshaking) method.
Uses both handshaking methods.
XON/XOFF
CTS/DTR
No flow control is used.
Sets Word parity
PROTOCOL
BOTH
SOFTWARE
HARDWARE
NONE
PARITY
NONE
ODD
No parity
Odd parity
EVEN
Even parity
Sets Word length
DATA BITS
7
8
Seven bit Word length
Eight bit Word length
Sets the number of stop bits
One stop bit
STOP BITS
1
2
Two stop bits
Same as Serial Port A, for optional wireless
connection. If not installed, this displays
“NOT INSTALLED” when accessed.
SERIAL PORT B♦
Controls Parallel Port A communications
settings.
PARALLEL PORT A♦
Determines if messages are sent from the
printer to the host via the parallel port.
PORT DIRECTION
UNI-DIRECTIONAL
BI-DIRECTIONAL
One-way printer communication.
Enables
IEEE
1284
back-channel
operation.
Same as Parallel Port A, for optional
Ethernet connection. If not installed, this
displays “NOT INSTALLED” when
accessed.
PARALLEL PORT B♦
(Continued next page)
28
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Communications (continued)
HOST SETTINGS
Settings which affect all communications
with a host.
The number of seconds a communications
port must be idle before the printer may
process data from a different port. This
value is also used to “timeout” an image /
label download.
HOST TIMEOUT
10 SEC
(1-60)
Allows the operator to change the prefix
of the commands interpreted by the
printer.
CONTROL CODES ♦
STANDARD CODES
ALTERNATE CODES
ALTERNATE CODES 2
ALTERNATE CODES 3
Hex 01 = SOH command; Hex 02 = STX
command; Hex 0D = CR
Hex 5E = SOH command; Hex 7E = STX
command; Hex 0D = CR
Hex 5E = SOH command; Hex 7E = STX
command; Hex 7C = CR
Hex 5E = SOH command; Hex 23 = STX
command; Hex 0D = CR
Returns a Hex 1E, [RS], after each label
successfully prints, and a Hex 1F, [US],
after each batch of labels is printed.
Feedback characters are sent to the host.
No feedback characters are sent.
FEEDBACK MODE
ENABLED
DISABLED
J693
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.6
Diagnostics
HEX DUMP MODE
Most commonly used mode for trouble
shooting. Prints data and instructions
received from the host rather than
interpreting them (see Section 6.2).
Prints raw ASCII data received from the
host rather than executing the
commands.
Executes and prints label formats
(normal operating mode).
ENABLE
DISABLE
OPTIONS TESTING
Tests currently installed options
Performs a functional test of the Present
Sensor circuitry.
TEST PRESENT SENSOR
Performs
a
functional test of the
TEST CUTTER
optional cutter mechanism and circuitry.
PERFORM TEST
1 TIME
The cutter will cycle 1, 10 or 100 times
(user selects). The results of each
attempt will be displayed.
TEST
Tests the optional GPIO port, when
installed.
Performs a functional test of the GPIO
input circuitry.
Performs a functional test of the GPIO
output circuitry.
MONITOR GPIO INPUT
MONITOR GPIO OUTPUT
SENSOR READINGS
All Analog Sensor readings displayed
Live sensor values may be viewed. View
is toggled with forward and reverse
keys. Maximum values are shown here:
thermistor sensor, transmissive (gap)
media sensor (TRAN is replaced with
REFL when SENSOR TYPE is set to
reflective), ribbon motion sensor, 24 volt
power supply sensor.
THR TRAN RIBM 24V->
255 255 255 255
present sensor, head down, printhead
ranking resistor.
<- PS HD RANK
255 255 255
RIBBON SENSOR LIMITS
Displays ribbon sensor ADC low and
high values. A Level 2 reset is required
to change these values.
Approximate default values are shown
here (actual values will vary).
RIBBON ADC LOW HIGH
070 104
30
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Understanding the Display Messages
The printer generates and displays four different types of information (if not in
the menu system or Quick Test Mode):
User Prompts and Condition Messages
Application Update Messages (see Section 5.6)
Fault Messages (see Section 6.1)
Warning Messages (see Section 6.1)
4.2.1
The User Prompts and Condition Messages
User Prompts indicate a required user operation. When outside the menu system,
Condition Messages indicate a current printer operation or state.
User Prompts and Condition Messages:
Displayed Message
Description
Condition(s)
The printer is trying
to clear a fault
condition.
Occurs when the FEED
key is pressed after the
correction of a fault.
A calibrated feed
operation is being
performed.
The FEED key was pressed
and held four seconds, or
during a label feed when
the TOF was expected but
the media sensor did not
detect one.
The CANCEL or
TEST key was
pressed during a
batch job.
The current print batch will
be cancelled if ENTER is
pressed; the remaining
labels will not be printed.
Security protection is You are attempting to enter
enabled on the
printer. Provide the
Menu Mode; however, a
password entry is required
correct user-definable for access.
password to proceed.
(Continued next page)
J693
31
Download from Www.Somanuals.com. All Manuals Search And Download.
User Prompts and Condition Messages (continued):
Displayed Message
Description
You are now
entering the Menu
Mode and existing
host changes have
affected the menu
settings.
Condition(s)
Pressing ENTER will save
these host changes to the
menu; otherwise, the
printer will revert to
previously saved settings.
The printer is paused The printer is in a paused
or offline.
condition.
The print job is
being processed.
Batch status indication,
updated with each label
printed.
Note: If the printer is
powered off while labels
remain to be printed,
printing will resume upon
power up.
Normal operating mode.
The printer is ready to
receive and process label
formats.
READY Mode.
A label blocks the Present
Sensor; remove it to
continue printing.
The Present Sensor
option is enabled and
a printed label is
awaiting removal.
(Continued next page)
32
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
User Prompts and Condition Messages (continued):
Displayed Message Description
You are now exiting Menu changes have
Condition(s)
the menu, but have affected the configuration
made changes to the of the printer.
settings of the
Note: If changes have
printer. Pressing
‘ENTER’ will save
these changes; if not,
the printer will revert
to previously saved
settings.
been made that require a
printer reset, the printer
will automatically invoke
that reset.
Normal power-up /
soft reset condition.
Follows the ‘SYSTEM
RESET IN PROGRESS’
message after a reset or
power-up.
Normal power-up /
soft reset condition.
Occurs when the user
resets the printer via the
host or Front Panel.
Printer calibration
not set.
Perform calibration. See
Section 5.2.
J693
33
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Printing from the Quick Test Mode
This section explains the functions of the resident Quick Tests, accessible by
pressing the
key on the Front Panel.
Notes: With the exception of the Configuration Label, all Quick Test labels
require 4-inch (102mm) wide media to capture all format
information. When using less than full width media, change the
Label Width setting to the width of the material to avoid printing on
the platen (see Section 4.1.2).
During any Quick Test Label run, pressing the
key will stop printing.
key or the
4.3.1
Print Quality Label
The Print Quality Label provides an indication of overall print quality at a
selected heat and speed setting. Consisting of fence and ladder type compliant
bar codes, assorted font sizes and graphic fill patterns, its format can be used to
ensure conformance, as well as visual aesthetics. To print a Print Quality Label:
Press the
Use the
key.
key to
scroll to ‘Print Quality
Label’.
Use the
key to
select a quantity; see Section
4.0.3.
Press the
key to
start printing.
34
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3.2
Configuration Label
Notes: To print all Configuration Label information, the media cannot be less
than 2 inches wide (51mm) and the Label Width setting must match
the width of the media being used (see Section 4.1.2).
The Configuration Label content can vary with the application version
and model of the printer.
The Configuration Label provides valuable printer database information, as
detailed in Section 4.1. To print a Configuration Label:
Press the
Use the
key.
key to scroll
to ‘Print Configuration’.
Press the
key to
start printing.
J693
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3.3
Quick Ribbon Test Label
The Ribbon Test Label features a compliant picket-fence bar code that can be
used to verify ribbon and print quality functions. To print a Ribbon Test Label:
Press the
Use the
Use the
Press the
key.
key to scroll to ‘Ribbon Test Label’.
key to select a quantity; see Section 4.0.3.
key to start printing.
36
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3.4 Dot Test Pattern Label
The Dot Test Pattern Label tests the printhead to determine the condition of each
thermal element. Pattern examples are shown below. To print a Dot Test Pattern
Label:
Press the
Use the
key.
key to scroll to ‘Dot Test Pattern’.
Use the
key to select a quantity; see Section 4.0.3.
key to start printing.
Press the
Good Test Pattern Label:
Even pattern consistency
indicates the printhead is
operating normally.
Faulty Test Pattern Label:
Streaks can indicate a dirty
or faulty printhead. See
Section 5.5 for cleaning
instructions.
J693
37
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3.5
Validation Label
The Validation Label is another useful tool for evaluating print quality. To
generate a Validation Label:
Press the
Use the
Use the
Press the
key.
key to scroll to ‘Validation Label’.
key to select a quantity; see Section 4.0.3.
key to start printing.
4.3.6
User Defined Label
The User Defined Label will reprint the last label printed (unless the printer was
powered-off between the printing of the last label and the request to print a user
defined label). This label is recalled from the print buffer and can be any of the
Quick Test labels, a label format from the host, or a label format recalled from a
memory module.
38
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
)
The correct hardware adjustments, regular maintenance, and calibrations
found in this section will help ensure continued peak printer performance.
5.0 Media Sensor Adjustment
The laterally adjustable Media Sensor detects the presence of media and the top-
of-form of all media types except continuous stock, which is set through
programming. For proper detection, the Sensor Eye Mark should be positioned
as noted in the table below. If messages such as ‘Out Of Stock’ or ‘Top of Form
Fault’ appear, the sensor position may need adjustment.
Media Type*
Sensor Type
Sensor Eye Mark Position
Standard die-cut
Gap
Near the middle of the label
*See Section 7 for an explanation of the media requirements.
To adjust the Media Sensor position:
With the printer powered ‘On’, media loaded, and the access cover open,
rotate the Printhead Latch forward to raise the printhead.
Pass the media through the Media Sensor then position the Sensor Eye
Mark over the label’s TOF mark (see drawing next page) by grasping and
moving the Slide Tab ‘in’ or ‘out’.
Lower the printhead by rotating the Printhead Latch to the locked position.
Close the Access Cover.
(Continued next page)
J693
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the Media Settings menu and verify that the correct ‘Sensor Type’ is
selected; see Section 4.1.1.
Exit the menu and return to READY mode.
Press and hold the FEED key until 2-3 labels are advanced (approximately
4 seconds) to set the TOF; see Section 5.1. If ‘Uncalibrated’, ‘Top of Form
Fault’, or ‘Position Error’ is displayed go to Section 5.2.
Note: Start of print position changes can be made using the Print
Control/Row Adjust or Row Offset (see Section 4.1.2).
40
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 Positioning Calibration
The Positioning Calibration sets the printer’s TOF, calculates the label length,
and calibrates the ribbon sensor on printers equipped with the thermal transfer
option. Perform this procedure for:
Die-cut and reflective media –
•
•
•
•
After changing media.
After a Media Sensor Calibration.
When a ‘Position Fault’ message is displayed.
When a ‘Ribbon Fault’ message is displayed while ribbon is installed.
Continuous media –
When a ‘Ribbon Fault’ message appears while ribbon is installed.
•
To perform a Positioning Calibration:
With media and ribbon (for thermal transfer equipped models) loaded, press and
hold the FEED key for approximately 4 seconds or until 2-3 labels advance.
Upon completion, the ‘Ready’ message will be displayed.
Notes: If ‘Uncalibrated’ is displayed, first calibrate the Media Sensor; see
Section 5.2.
If a ‘Ribbon Fault’ is displayed, first perform a Level 2 reset before
calibrating; see Section 4.0.6. (Ribbon Calibration must be performed
with a ribbon installed and with the printer configured for the thermal
transfer printing; see Section 4.1.1.)
5.2 Media Sensor Calibration
Media Sensor calibration should be performed during initial printer setup, if
switching media types, or if an ‘Uncalibrated’ message is displayed. To ensure
that each label is detected correctly and reliably, two different methods are
available to calibrate the printer: Standard and Advanced Entry.
5.2.1
Standard Calibration
The first calibration method is appropriate for most media types. The printhead
is raised for visual access to the media. Sensor readings are displayed to provide
an indication of the sensor’s best position over the media, a position that
becomes critical when using reflective or notched stock with a small TOF mark.
(Continued next page)
J693
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Three Media Sensor readings are required:
Empty:
Mark or Gap: Only the backing material, notch, or reflective mark in the sensor.
Paper: The label (with the backing material attached) in the sensor.
Nothing in the sensor.
To perform a Standard Calibration:
Step
Operator Action
Displayed Message
Comment
Wait until
Turn ‘On’ the printer.
1
‘Ready’ is
displayed.
2
See Section
4.0.2 for
details.
Press the
Menu Mode.
key to enter
Raise the printhead for
visual access to the Media
Sensor and load label
media.
3
4
5
Press the
enter the Media Settings
menu.
key to
See Section
4.1.1 for
details.
Press the
key.
See Section
4.1.1 for
details.
Press the
the
to the desired sensor type
key. Use
key to scroll
See Section
4.1.1 for
details.
and press the
to enable the selection.
key
The enabled
selection will
be indicated
with an *.
(Continued next page)
42
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Press the key. Use
the key to scroll
to ‘Sensor Calibration’.
Displayed Message
Comment
6
See Section
4.1.1 for
details.
Press the
key to
abort this
procedure.
7
8
Press the
Press the
key.
key.
See Section
4.1.1 for
details.
Sets the
Ensure no label media is in
the Media Sensor then press
any key.
parameter for
the ‘out of
stock’
condition.
‘yyy’ is a
numerical value
representing the
current sensor
reading.
(Continued next page)
J693
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Displayed Message
Comment
Sets the
parameter for
the ‘gap’ or
9
Proceed according to the
media type:
-OR-
Die-cut stock: remove
approximately six inches
of label material from the
backing (liner) and place
the backing under the
Sensor Eye Mark.
‘mark’ value.
‘yyy’ is a
numerical value
representing the
current sensor
reading.
Notched stock: place the
notched area in the sensor
and adjust the Sensor Eye
Mark over the notch.
If the ‘Sensor
Type’ is set to
‘Continuous’,
this step is
Reflective media: place
the black mark (face
down) in the sensor and
adjust the Sensor Eye
Mark over the black
mark.
skipped, going
directly into
Step 10.
Press any key to continue.
Note: After the Media Sensor has been adjusted, do not readjust
the position.
(Continued next page)
44
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Displayed Message
Comment
10 Place the label (and
backing) under the Sensor
Eye Mark.
Calculates the
parameter
settings for the
‘Paper’ value.
Press any key to continue.
‘yyy’ is a
numerical value
representing the
current sensor
reading.
11 Depending upon the
‘Sensor Type’ selection,
observe the display for the
calibration message.
See
‘Calibration
Problems’
(listed below)
for other
possible
-OR-
-OR-
messages.
12 Exit upon successful
calibration: press the
key to back out
After saving the
settings, press
and hold the
FEED key,
approximately
4 seconds, to
calibrate the
label position.
of the menu tree, when
prompted to save the
settings press the
key to return to the Main
Menu.
J693
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Calibration Problems: If problems occur during calibration, one of the
following messages will be displayed. The ‘Comment’ column addresses the
most likely cause and the corrective action to be taken (if any) for each situation.
Displayed Message
Action
Comment
Press any key. The printer measured only a small
difference between the ‘empty’ and
‘gap’ readings. Transparent
backing or notched type media
typically gives this indication. In
this case, there may be a slight
delay in the ‘Out of Stock’
indication, after the media supply is
emptied.
Or:
Displayed Message
Action
Comment
Press any key. Only a small difference or no
change in low sensor readings was
detected. Ensure that nothing is
stuck in the media sensor. Retry
calibration. If the problem persists,
perform the ‘Advanced Entry
Calibration’; see Section 5.2.2. If in
reflective mode – REFLECTIVE
MODE will be displayed instead of
GAP MODE.
Or:
Displayed Message
Action
Comment
Press any key. Consistently high readings were
received which could indicate a
faulty sensor. Ensure that no labels
are stuck in the media sensor. Retry
calibration. If the problem persists,
call for service.
When in reflective mode –
REFLECTIVE MODE will be
displayed instead of GAP MODE.
46
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.2
Advanced Entry Calibration
The second calibration method is the Advanced Entry Calibration. This method
overrides all previous calibration settings and should be used only when the
Standard Calibration method has failed. The procedure has two parts:
1) Sensor Gain: Different algorithms are used for sampling, to produce
different measurements for the media.
2) Sensor Levels: At a selected gain, values are directly input for ‘Paper’,
‘Mark’ or ‘Gap’, and ‘Empty’ variables.
To perform an Advanced Entry Calibration:
Step
Operator Action
Displayed Message
Comment
1
Turn ‘On’ the printer.
2
See Section
4.0.2 for
details.
Press the
Menu Mode.
key to enter
Raise the printhead
assembly for visual access
to the Media Sensor and
media.
3
Press the
enter the Media Settings
menu.
key to
See Section
4.1.1 for
details.
4
5
Press the
key.
See Section
4.1.1 for
details.
Press the
the
the desired sensor type and
press the key to
enable the selection.
key. Use
key to scroll to
See Section
4.1.1 for
details.
The enabled
selection will
be indicated
with an *.
(Continued next page)
J693
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Displayed Message
Comment
Press the
Use the
scroll to ‘Sensor
Calibration’.
key.
key to
6
See Section
4.1.1 for
details.
Press the
Press the
key.
key to
abort this
procedure.
Use the
scroll to ‘Advanced Entry’.
Press the
key to
7
8
9
See Section
4.1.1 for
details.
key.
Press the
key.
See Section
4.1.1.
Place the label under the
Sensor Eye Mark and lower
the printhead.
Ensure that an
unmarked label
area (without
pre-printing) is
in the Media
Sensor.
-OR-
Using the
increment the Gain
Number. Press the
key
key to select the new setting
and then record the sensor
reading (the ‘yyy’ value).
Repeat this process for each
of the 16 Gain Numbers.
These are the Label Values.
(Continued next page)
48
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Displayed Message
Comment
‘yyy’ is a
numerical value
representing the
current sensor
reading.
10 Proceed according to media
type:
Die-cut stock: remove
approximately six inches
of label material from the
backing and place the
backing under the Sensor
Eye Mark. Lower the
printhead.
-OR-
Notched stock: place the
notched area in the sensor
and adjust the Sensor Eye
Mark over the notch.
Lower the printhead.
Reflective stock: place
the black mark (face
down) in the sensor and
adjust the Sensor Eye
Mark over the mark.
Lower the printhead.
Note:
After the
Media
Sensor has
been
adjusted, do
not readjust
the position.
Using the
increment the Gain
Number. Press the
key to select the new setting
and then record the sensor
reading (the ‘yyy’ value).
key
Repeat this process for each
of the 16 Gain Numbers,
recording each value.
These are the TOF Values.
(Continued next page)
J693
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Displayed Message
Comment
‘yyy’ is a
numerical value
representing the
current sensor
reading.
11 Using the Gain Number
data collected from Steps 9
and 10, subtract each Label
Value from the TOF Value.
From the resulting list of
Difference Values, select
the largest number. Its
-OR-
Both sensor
readings must
be above 20.
associated Gain Number is
the best selection for the
media. See the example
from below.
Gain Number
Label Value
255
TOF Value
254
240
213
182
150
119
88
Difference Value
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
1
11
28
49
69
93
112
131
146
147
139
130
121
111
102
98
251
241
231
219
212
200
189
178
167
156
146
136
126
116
112
58
32
20
17
16
15
15
14
14
Example from the data compiled in the table above: Gain Algorithm
Number 8 should be used because it has the highest difference value
(146) where both the Label Value and the TOF Value is above 20.
(Continued next page)
50
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Displayed Message
Comment
Using the
key,
select the Gain Number as
determined in Step 11.
12
When enabled,
the selection
will be
indicated with
an *.
Press the
enable the entry.
key to
-OR-
13 Using the ‘Gain Number’
set in Step 12, complete the
following steps:
‘yyy’ is a
numerical value
representing the
current sensor
reading.
-OR-
Place the label under the
Media Sensor. Record
the sensor reading and
label it “P” (paper).
Place the backing, mark,
or notch under the Media
Sensor. Record the
sensor reading and label
it “G” or “M” (gap or
mark respectively).
Remove all media.
Record the sensor
reading and label it “E”.
Press the
then press the
key. And
key.
14
(Continued next page)
J693
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Step
Operator Action
Displayed Message
Comment
Press the
key.
15
Using the
or the
key set the ‘Paper’
level to the value
determined in the previous
step. Press the
to set the entry and advance
the menu.
key
-OR-
Repeat for the ‘Mark’ or
‘Gap’ and ‘Empty’ levels.
Press the
back out of the menu and
then press the
to save the settings and
return to the Main Menu
and Ready Mode.
key to
16
From Ready
Mode, press
and hold the
FEED key,
approximately
4 seconds, to
calibrate the
label position.
key
52
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Printhead Adjustments
5.3.1
Burn Line Adjustment
The Burn Line is the row of thermal elements extending the length of the
printhead. At the factory, the printhead has been adjusted to meet strict print and
bar code compliance requirements with 6.5-mil (.0065″) media, enabling the
printer to accommodate a majority of media types.
Depending upon the equipped printing option, the printhead alignment is
slightly different. Thermal transfer models have the Burn Line positioned
slightly forward of the Platen Roller vertex to allow the liquefied wax/ink to
separate easily from the ribbon base-film and adhere to the label while still hot.
Direct thermal models have the Burn Line positioned over the vertex for the
more efficient heat transfer.
When media with a different thickness or rigidity is used (e.g., heavy tag stock),
an adjustment may be needed if the print quality has been adversely affected.
Generally, thicker media requires a slight forward adjustment of the printhead
and thinner media requires a slight backward adjustment to compensate for the
resulting change in the Burn Line to vertex relationship.
To adjust the Burn Line of the printhead:
With the printer loaded with media (and ribbon, if thermal transfer
printing), lower and rotate the Printhead Latch to the locked position.
Loosen the two Locking Screws.
Turn the Adjustment Screws counter-clockwise until the Burn Line is past
the Platen Roller vertex. Print a Validation Label from the Quick Test
menu. The label should look light and uneven.
Tighten the Locking Screws just until they are ‘snug’– tight enough to
remove any play in the printhead assembly, yet loose enough to allow the
Adjustment Screws to move the printhead.
(Continued next page)
J693
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn each Adjustment Screws clockwise about ¼ a turn (or 1/8 a turn for
finer adjustments). Print another Validation Label and examine the print
quality. Repeat this step until labels with even print contrast (darkness) and
acceptable print quality are produced.
Tighten the Locking Screws. Print a final Quick Test label to verify the
adjustment.
Note: When the Locking Screws are ‘snug’, turning the Adjustment Screws
counter-clockwise will not move the printhead outward. If you have
adjusted the printhead too far inward, restart the entire procedure.
54
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 Printhead Replacement
Notes: The printhead is fragile; use extreme care when handling and never
use a sharp object on the printhead surface.
If you have any questions or concerns regarding this procedure,
contact a qualified technician.
Locating pins eliminate the need for an alignment following the installation of a
new printhead. To replace the printhead:
Touch a metal part of the printer’s frame to discharge any static electricity
that may be present on your body.
Turn ‘Off’ and unplug the printer. Open the Access Cover, rotate the
Printhead Latch forward and raise the printhead. Remove the ribbon, if
installed.
Lower and rotate the
Printhead Latch to the locked
position.
Loosen the Printhead
Mounting Thumbscrew (it
will remain captive in the
assembly). Rotate the
Printhead Latch forward to
the unlocked position.
Raise the assembly and while carefully holding the Printhead, disconnect
the two Cables and then remove the Printhead.
While carefully holding the
new Printhead, reconnect
both Cables.
Position the Printhead onto
the Locating Pins in the
Printhead Assembly and
secure in place with the
Printhead Mounting Screw.
(Do not over-tighten this
screw.)
Clean the Printhead; see
Section 5.6.1.
Reload ribbon, if removed. Lower and rotate the Printhead Latch to the
locked position. Plug in and turn ‘On’ the printer.
J693
55
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5 Cleaning Schedule
A clean printer operates efficiently. The following list of cleaning items and
table below provides the recommended schedule and technique for cleaning the
various parts of your printer safely and effectively.
•
•
•
•
•
•
Isopropyl alcohol
Cotton swabs
A clean, lint-free cloth
Soft-bristle brush
Soapy water/mild detergent
Compressed air
For your continued safety and to avoid damage, always turn ‘Off’
and unplug the printer before cleaning.
Isopropyl alcohol is a flammable liquid; always take proper
precautions when using this solvent.
CAUTION
Recommended Cleaning Schedule
Area
Method
Interval
Printhead Using a cotton swab dampened with isopropyl
alcohol, clean the printhead from end to end,
removing all build-up. See Section 5.5.1.
Clean after
each roll or
box of labels,
or after each
roll of ribbon.
WARNING! Before cleaning, allow the
printhead to cool.
Platen
Roller
Using a cotton swab dampened with isopropyl
alcohol, rotate the platen and remove all build-
up. See Section 5.5.2.
Clean after
each roll or
box of labels,
or after each
roll of ribbon.
Media
Compressed air / soft-bristle brush and isopropyl As needed,
Path / Tear alcohol. Remove all build-up along the path that based on a
Plate
the ribbon and paper follow through the printer. weekly visual
inspection.
Media
Sensor
Compressed air, isopropyl alcohol if needed.
Remove all build-up.
Monthly or as
needed.
Interior
Soft-brush or compressed air. Remove all build- As needed.
up. See Section 5.5.3.
Exterior Mild detergent. Remove all build-up. See As needed.
Section 5.5.3.
56
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5.1
Cleaning the Printhead
When print quality begins to decline (indicated by symptoms including non-
compliant bar codes, print dropouts, and streaking), the typical cause is debris
build-up on the printhead (see Section 4.3.4). Furthermore, if this build-up is not
removed it may lead to premature element failures, greatly reducing the life of
the printhead. To clean the printhead:
Turn ‘Off’ and unplug the printer.
Open the access cover. Unlock the Printhead Latch and raise the Printhead
Assembly. Move media and ribbon away as necessary.
Gently wipe away all surface build-up on the Printhead (see below) using a
cotton swab moistened, not soaked, with isopropyl alcohol. Allow the
printhead to dry.
Re-install ribbon and media, if removed. Lower and rotate the Printhead
Latch to the locked position.
Close the cover. Plug in and turn ‘On’ the printer. Feed several labels to
normalize tracking.
NEVER use a sharp object to clean the Printhead.
CAUTION
J693
57
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5.2
Cleaning the Platen Roller
A platen roller contaminated with grit, label adhesive, or ink can cause a decline
in print quality and, in extreme cases, cause labels to stick and wrap around the
roller. To clean the platen roller:
Turn ‘Off’ and unplug the printer.
Open the access cover. Unlock the Printhead Latch and raise the Printhead
Assembly. Remove media and ribbon.
Using a Cotton Swab dampened with isopropyl alcohol, clean the Platen
Roller; manually rotate the roller and repeat, cleaning the entire surface.
Allow the Platen Roller to dry.
Replace ribbon and media.
Lower the Printhead Assembly and lock the Printhead Latch.
Close the access cover. Plug in and turn ‘On’ the printer. Feed several labels
to normalize tracking.
NEVER use a sharp object to clean the Platen Roller.
CAUTION
58
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.5.3
Cleaning Interior and Exterior Surfaces
Interior Surfaces: During operation, dust particles from the media build-up
inside the printer. Then, as the media is pulled through the printer, the particles
can become attached and cause voids on the printed labels. To prevent this, turn
‘Off’ and unplug the printer. Remove all media. Using a soft bristle brush or
compressed air, clean out the interior of the printer.
Exterior Surfaces: The outer surfaces of the printer should be cleaned using a
general-purpose cleanser. Never use abrasive cleansers or solvents. To clean,
turn ‘Off’ and unplug the printer. Using a soft cloth or sponge dampened with
the cleanser, wipe the exterior surfaces until clean.
5.6 Updating the Application Program
The printer stores its application program in Flash memory on the Main PCB. A
feature is included that allows updates to this program through any printer
interface port. Updates can be found on our web site. There are two modes in
which the firmware of the printer can be updated: (1) the Ready Mode, or (2) the
Download Mode.
Should an error occur during the file download (see Section
5.6.3), the update is aborted. If this process did not reach ‘Erasing
Flash’ or ‘ Updating Software’, the previous program is left intact;
otherwise, a successful download must be completed before the
printer is operable.
WARNING
Note: After updating from 2.xx to 3.xx firmware for the first time, you must
also download the EFIGS menu language file and copy 832296.01C
(or most current version) to lpt1: /b (the DOS Copy command requires
the /b parameter because this file contains binary code).
Before beginning an update, identify the current version of the printer’s
application program by printing a Configuration Label (see Section 4.3.2).
Compare that version string to those filenames available from our web site and
then download the desired file onto your computer’s hard drive.
Proceed with the printer update accordingly:
If the current application version is 2.091 or greater, refer to Section 5.6.1
or Section 5.6.2.
If the current application version is 2.08 or less, start with Section 5.6.2.
J693
59
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6.1
Updating from the Ready Mode
Update Procedure for Application Version 2.091 or greater
Step Displayed Message Operator Action
Comment(s)
Using the DOS
copy command
As an example, this would be
entered as: copy
1.
(where ‘filename’ 4212tb10_0304.zs lpt1:
is the program to
be loaded and
‘lpt1’ is the
selected interface
port), enter the
following:
(where ‘lpt1’ is the host
computer’s port; however,
this selection can differ to
include a serial or other port,
as the printer is equipped).
The Ready Indicator will
copy filename lpt1: flash while the data is
received.
No action required. The new application program
is being stored and verified.
2.
3.
No action required. The printer has reset
automatically and is now
displaying the new firmware
version.
No action required. The new application is now
running.
4.
Note: If ‘Uncalibrated’ or
‘Position Fault’ is displayed,
the printer will have to be
calibrated (see Section
5.2).
60
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6.2
Updating from the Download Mode
Required Update Procedure for Application Version 2.08 or earlier*
Step Displayed Message
Operator Action
Comment(s)
Press and hold the The Boot Loader version
PAUSE and TEST is displayed.
1.
keys while turning
‘On’ the printer to
enter the Download
Mode.
Note: This information
will vary with the printer
model and Boot Loader
version.
Using the DOS
copy command,
The printer is ready to
accept the new application
2.
copy the filename version.
to the printer (see
Step 2 in Section
5.6.1).
Note: The parallel port
(LPT1) must be used to
write to the printer.
No action required. The printer is receiving
the new image (program).
3.
4.
No action required. The program has been
received and verified; now
Flash memory is cleared
of the previous
application.
No action required. The new program is being
written into Flash memory.
Upon completion, the
5.
printer will automatically
reset, starting the new
application; however,
before continuing, the
printer must be re-
calibrated; see Section 5.2.
*This can also be used as an alternate download method for all other version levels.
J693
61
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6.3 Application Update Problems
Note: If experiencing trouble when attempting to download the file to the
printer, try the following alternate methods:
1) Use the download procedure in Section 5.6.2.
2) Windows users – try restarting the computer in MS-DOS mode.
3) Use a Windows Driver – ‘Send File to Printer Function’.
The following is list of possible update error messages:
Application Update Error Messages
Displayed Message
Descriptions / Causes / Solutions
The printer detected an error during the
decompression and transfer of file data from
cache storage into the Flash memory. Confirm the
version and retry the download; however, if the
problem continues call for service.
The printer could not successfully erase Flash
memory. The possible cause is defective Flash
memory. Try the download again; however, if the
problem continues call for service.
The printer could not successfully write the
program into Flash memory. A possible cause is
defective Flash memory. Try the download again;
however, if the problem continues call for service.
Application Firmware downloaded was not
compatible with the printer’s Main PCB (i.e.,
firmware used was for a different model and not
supported by this boot loader version). See
Section 4.1.4 – Configuration Level.
The printer detected an error in the download. The
possible causes include:
• An invalid or corrupted file was downloading;
try saving the file to the host and then download
again.
• Communications error. Recheck cabling and
port setting.
Reserved for future use. If this message is
consistent, call for service.
62
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
5.7 Updating the Boot Loader Program
The printer stores the Boot Loader Program in Flash memory on the Main PCB.
A feature allows updates to this program via the printer’s interface port. Updates
can be found on our web site.
If power is lost while “Upgrading Software” is displayed, the
printer will become non-functional and must be returned to the
factory for programming or the main board replaced.
WARNING
Note: Only printers with an Application Version of 2.09 or greater can
update the Boot Loader Program.
Before beginning the Boot Loader update, identify the printer’s current version.
Print a Configuration Label (see Section 4.3.2) and compare that version string
to those available from our web site. Download the desired version onto your
computer’s hard drive. To update the Boot Loader Program:
Boot Loader Update Procedure
Step Displayed Message Operator Action
Comment(s)
Using the DOS
copy command
As an example, this would be
entered as: copy
1.
(where ‘filename’ boottb99_0209.bs lpt1: (where
is the program to
be loaded and
‘lpt1’ is the
‘lpt1’ is the host computer’s
output port; however, your
selection can differ to include
selected interface a serial or other port, as the
port), enter the
following:
printer is equipped).
The Ready Indicator will flash
copy filename lpt1: while the data is received.
No action required. The new application program
is being stored and verified.
2.
No action required. The printer has reset
automatically.
3.
4.
No action required. The new application is now
running.
Note: If ‘Uncalibrated’ or
‘Position Fault’ is displayed,
the printer will have to be
calibrated (see Section
5.2).
J693
63
Download from Www.Somanuals.com. All Manuals Search And Download.
64
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
6.0 Troubleshooting Tips
If a problem arises with the printer, the information in this section will help you
resolve it. Use this guide as a starting point in troubleshooting. If you have
questions, or if problems persist, contact a qualified service technician or a
Technical Support Representative. The following are problems that will not
necessarily generate a message (see Section 6.1 for Fault and Warning
Messages).
If experiencing this problem…
Try this solution…
Cannot communicate through
the parallel port:
Be sure the parallel cable is connected and is
the correct type for the application. Try
setting the ‘Parallel Port Direction’ to Uni-
Directional; some host computers are not bi-
directional compatible. See Section 4.1.5.
Display is blank, but the
READY indicator is ‘On’:
The display contrast may set too low. Press
and hold the MENU key for 10 seconds or
until the display reappears.
Erratic printing (strange
characters instead of label
formats print):
• The printer may be in ‘hex dump mode’;
see Section 6.2. Enter the Diagnostics
menu and disable this mode; see Section
4.1.6. Exit the menu, save changes and
return to the ‘READY’ mode.
• If using the serial port for communicating,
check both the host and printer port
configuration; the printer may be set for 8
data bits while the host is set for 7 bits (or
vice versa).
(Continued next page)
J693
65
Download from Www.Somanuals.com. All Manuals Search And Download.
If experiencing this problem…
Try this solution…
Intellifont will not print:
Intellifont format is Little/Big Endian
specific. The printer uses Big Endian. Refer
to your font supplier for information.
Light print on the right side
(facing the printer) of the
label:
• The Printhead Leveling Cam may be
incorrectly adjusted; see Section 5.3.1.
• The Platen Roller may be dirty or worn;
see Section 5.5.2.
Missing information in the
printed label:
• Check the label format for character
placement outside the dimensions of the
label; all row/column values must allow
enough space for the height/length of the
characters and bar codes to be printed
within the format size.
• The available memory may have been
exceeded by the memory requirement of
the label format. Try reducing the memory
allocated to either the internal module or
scaleable font caches; see System
Settings/Memory Settings – Section 4.1.4.
Missing print on left or right Information may be formatted outside the
side of the label:
label dimensions. Check your software
program label size or check the values in the
menu for Print Control / Column Offset and
Print Control
/
Custom Adjustments
/
Column Offset; see Section 4.1.2.
(Continued next page)
66
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
If experiencing this problem…
Try this solution…
No power (all indicator lights
are ‘Off”):
• Verify that the AC power cord has been
made at both the outlet and the printer;
also, ensure the power switch is ‘On’.
• Verify that the AC outlet is functioning, or
try moving the printer to another AC
circuit.
• The AC cord may be damaged; replace it.
• The power switch may be defective or the
line fuse blown; call for service.
Nothing is printing (labels
advance normally, but no
image is printed):
Begin by examining the used ribbon for an
image.
If an image is on the used ribbon:
Verify that the ribbon was properly loaded
per Section 3.3.
If it was properly loaded, the wrong ribbon
coating configuration was used. Clean the
printhead (see Section 5.5.1). Use only
Pitney Bowes ribbons.
If no image is on the used ribbon:
• Run any Quick Test label; see Section 4.3.
If an image printed, then check the
protocol and port settings for both the
printer and host. These must match.
• The heat setting may be too low. Make an
adjustment in the software program or
through the Front Panel.
• The media/ribbon combination may be
incorrect. Contact a Media Representative.
• The printhead or printhead cable(s) may be
loose; power ‘Off’ and reconnect; see
Section 5.4 for locations.
(Continued next page)
J693
67
Download from Www.Somanuals.com. All Manuals Search And Download.
If experiencing this problem…
Try this solution…
Nothing happens when trying
to print using a software
program:
• Ensure that the printer is at READY.
• Observe the Front Panel, if the READY
light does not flash as you send the format
check the protocol and port settings
between the printer and host.
• Ensure the I/O cable meets the
requirements found in Section 3.0.1.
Poor print quality:
• The printhead may need cleaning; see
Section 5.5.1.
• Adjust these settings through the Front
Panel or by host commands, Heat, Print
Speed and Darkness; see Sections 2.1.1
and 4.1.2.
• The media/ribbon combination may not be
compatible; see Section 2.1.
• The Printhead Leveling Cam may be
incorrectly adjusted; see Section 5.3.1.
• The Platen Roller may be dirty or worn;
see Section 5.5.2.
• The Printhead Burn Line may need
adjusting; see Section 5.3.2.
Skips labels when printing:
• The printer may need calibration; see
Section 5.1 and 5.2.
• The Media Sensor may be slightly out of
position; readjust the position; see Section
5.0.
• The label format may be too close (within
1/8″ of the edge) to the start of the next
label. Try reducing or moving the format
slightly.
Unable to print rotated text:
• The characters may be formatted outside
the label dimensions. Ensure the
row/column values provide enough room
for the height of the characters or bar code
to be printed. See the Programmer’s
Manual for details.
68
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1 Fault and Warning Messages
When the printer detects a problem or the potential for a problem, a message is
displayed and the Error Indicator (see Section 4.0.4) will be illuminated. There
are two types of indications:
•
•
Fault Indication – the indicator ‘fast flashes’ with message.
Warning Indication – the indicator ‘slow flashes’ with message.
The Fault and Warning Messages are listed in the following two tables,
including a brief description of each and possible solution(s).
Note: After the printer enters a fault condition, the fault must be corrected
and then FEED key must be pressed to clear the condition.
Fault Messages:
Displayed Message
Description
Possible Solution(s)
The printer has
Try cycling the printer power
detected an analog ‘Off’ and ‘On’. If the fault
to digital circuit
converter failure.
does not clear, call for
service.
The printer has
detected a Direct
Memory Access
failure.
Try cycling the printer power
‘Off’ and ‘On’. If the fault
does not clear, call for
service.
(Continued next page)
J693
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault Messages (continued):
Displayed Message
Description
Possible Solution(s)
The printer cannot 1) Reload media.
detect media.
2) Ensure that the labels are
passing through the Media
Sensor.
3) Readjust the Media Sensor
over the TOF mark; see
Section 5.0.
4) Calibrate the printer; see
Section 5.2.
The printer has
Press and hold the FEED key
determined that the for 4 seconds; see Section 5.1.
media is not
Calibration may also be
correctly
needed. See Section 5.2.
positioned to print.
The printer has
Try cycling the printer power
detected a problem ‘Off’ and ‘On’. If the fault
in the print logic.
does not clear, call for
service.
The system has
detected a RAM
failure.
Try cycling the printer
power ‘Off’ and ‘On’. If the
fault does not clear, call for
service.
(Continued next page)
70
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault Messages (continued):
Displayed Message
Description
Possible Solution(s)
The ribbon sensor 1) Ensure that ribbon is
detects no or only
sporadic ribbon
supply hub
movement; or the
sensor values may
have changed.
correctly loaded with the
printhead locked down.
2) Check the ribbon supply
and ribbon take up hubs for
obstructions that may be
stopping movement.
3) Ensure that the ribbon
supply core fits snugly on
the ribbon supply hub.
Note: The
ribbon sensor
calibration will
only take effect
after a Level 2
reset has cleared
the previously set
values; see
4) Ensure that the media and
paper combination is
correct.
5) Perform a Level 2 Reset
(Section 4.0.6) and then a
Positioning Calibration
(Section 5.1).
Section 4.0.6.
The printer has
Try cycling the printer power
detected a problem ‘Off’ and ‘On’. If the fault
applying the
printhead heat
strobe.
does not clear, call for
service.
The printer has
Turn ‘Off’ the printer until
shutdown to allow cool to prevent permanent
the printhead
temperature to
cool.
damage due to an excessive
printhead temperature.
(Continued next page)
J693
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault Messages (continued):
Displayed Message
Description
Possible Solution(s)
If media is moving:
The printer could
not find the TOF
mark within the
maximum label
length setting or it
found a TOF in an
unexpected place.
1) Press the FEED key. It
may be necessary to re-
calibrate the printer; see
Section 5.2.
2) The Media Sensor may be
out of position. Readjust its
position; see Section 5.0.
3) The media may not be
properly loaded. Reload
media and ensure that the
Media Guide is positioned
properly; see Section 3.1.
4) The label may be longer
than the default value for
maximum length. Check
the Media Settings /
Maximum Label Length;
see Section 4.1.1.
5) The Media Sensor may be
obstructed. Check and
carefully remove any
obstruction (labels, paper
dust, adhesive, etc).
If media is not moving:
The printhead may not be
latched; close and lock the
printhead.
The printer has
detected a drop in
the 24-volt power
supply.
Try cycling the printer power
‘Off’ and ‘On’. If the fault
does not clear, call for
service.
72
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning Messages:
Displayed Message
Description
Action
The printer has
detected burned-
out printhead
elements.
Replace the printhead when
print quality becomes
unacceptable or if the
printed bar codes are non-
compliant.
The printer missed Readjust the media sensor
detecting a label
gap.
and recalibrate.
Power has been
removed and
shutdown is in
progress.
The printer power switch
was turned ‘Off’, the line
fuse has blown, or AC line
voltage has been lost.
The host has
pending
configuration
changes that will
To save changes, send a
host reset command (in
DPL) or to discard changes
perform a front panel reset;
not take effect until see Section 4.0.6.
a ‘host reset
command’ is
issued.
The printer has
detected a low
operating voltage.
A possible low or
fluctuating line voltage
level. Try moving the
printer to another outlet. If
this condition persists call
for service.
Ribbon will soon
need replacement.
Replace ribbon when
needed.
The printer was
unable to save
settings in
If the condition persists,
possible faulty Main PCB.
Call for service.
permanent
memory.
(Continued next page)
J693
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning Messages (continued):
Displayed Message
Description
Action
A high printhead
temperature has
been detected.
Allow printhead to cool.
The previous
warning condition
has been corrected.
No further action is
necessary.
6.2 Hex Dump Mode
The hex dump mode is a useful tool for diagnosing problems, including
communication and DPL syntax errors, allowing a comparison of input strings
(sent by host) to output data (received by printer). To decode this information,
the Programmer’s Manual is an essential reference. This output can be used for
debugging the label format. And by repeatedly sending a format, this mode can
uncover handshaking problems (if they exist). Handshaking problems are
identified by sections of missing data in the character string.
To begin, go to the Diagnostics menu and enable Hex Dump Mode; see Section
4.1.6. Exit the menu, save changes and returning to the ‘READY’ mode. Now
all data sent to the printer will now be output in hexadecimal code, along with
the printable ASCII equivalents.
The figure below is a sample Hex Dump Label. After sending a label format to
the printer, the hex code output will be immediate. As a final note, many
software programs use bit mapping to construct the label, making diagnosis
difficult. Contact a Technical Support Representative with any questions.
Note: To exit the hex dump mode, re-enter the Diagnostics Menu and disable
the Hex Dump Mode, exit the menu, then save the changes to return to
the ‘READY’ mode.
74
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂ
7.0 Printer Specifications
Bar Codes
(See the Programmer’s Manual for details. See Appendix B for visual samples.)
Code 39, Interleaved 2 of 5, Code 128 (subsets A, B and C), Codabar,
LOGMARS, UPC-A, UPC-E, UPC 2 & 5 digit addendums, EAN-8, EAN-13,
EAN 2 & 5 digit addendums, UPC Random Weight, Code 93, Plessey,
Universal Shipping Container Symbology, Code 128 MOD 43, Postnet,
USS/EAN-128 Random Weight, Telepen, UPS MaxiCode (modes 2 & 3),
PDF417, Data Matrix and QR Code.
Fonts
9 Bit-Mapped Fonts, rotatable 0, 90, 180, 270 degrees
CG Triumvirate Scalable Font
CG Triumvirate Condensed Bold Scalable Font
Communications
Interfaces:
EIA RS-232/DB-25 Serial, and IEEE 1284
Compliant Parallel
Serial Data Rates:
Handshaking:
Parity:
2400, 4800, 9600, 19.2K, and 38.4K baud.
Xon/Xoff; CTS/DTR
Even, Odd, or None
1 or 2
Stop Bits:
Data Bits:
7 or 8
Electrical
Input Voltage:
90 – 132 or 180 – 264 VAC @ 47–63 Hz, auto-
ranging.
Power Consumption:
Grounding:
Typical Operating: 90 Watts / Standby: 10 Watts
Unit must be connected to a properly grounded
receptacle.
J693
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental Requirements
Operating Temperature:
Storage Temperature:
Humidity:
32° F – 100° F (0° C to 38° C)
0° F −140° F (-17° C to 60° C)
10% − 95% non-condensing
Non-conducting, non-corrosive
Dust:
Electromagnetic Radiation: Moderate RF fields can be tolerated
Mechanical
Height:
Width:
Depth:
Weight:
12.70" (322.6mm)
12.62" (320.6mm)
18.60" (472.5cm)
45 lbs. (20.5 kg)
Printing Specifications
Printing Type:
Direct Thermal or optional Thermal Transfer
Print Speed:
2 – 8 IPS (50.8 – 203.2 mmps)
203 DPI (8 dots/mm)
Printhead Resolution:
Nominal Dot Size:
.0043" x .0052" (.109mm x .132mm)
Printhead Protection
Type:
Thermistor Sensor. Temporary shutdown of
printing occurs upon over-temperature detection;
printing resumes automatically after cool-down.
SDRAM Memory:
Flash Memory:
8 MB
1 MB
Maximum Print Width:
Print Length Range:
Print Justification:
4.09" (103.9 mm)
.25" – 99" (6.35mm – 2514.6mm)
Left
76
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
$
ASCII Control Code Chart
Char
NUL
SOH
STX
EXT
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
Esc
FS
GS
RS
Dec
0
1
2
3
4
5
6
7
Hex
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
Char
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Hex
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
Char
@
A
B
C
D
E
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Hex
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
Char
Dec
96
97
98
99
Hex
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Ctrl @
Ctrl A
Ctrl B
Ctrl C
Ctrl D
Ctrl E
Ctrl F
Ctrl G
Ctrl H
Ctrl I
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
!
“
#
$
%
&
‘
(
)
*
+
,
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
8
9
Ctrl J
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Ctrl K
Ctrl L
Ctrl M
Ctrl N
Ctrl O
Ctrl P
Ctrl Q
Ctrl R
Ctrl S
Ctrl T
Ctrl U
Ctrl V
Ctrl W
Ctrl X
Ctrl Y
Ctrl Z
Ctrl [
-
.
/
0
1
2
3
4
5
6
7
8
9
:
s
t
T
U
V
W
X
Y
Z
[
\
]
^
u
v
w
x
y
z
{
|
;
Ctrl \
Ctrl ]
Ctrl ^
Ctrl _
<
=
>
?
}
~
US
_
(Continued next page)
J693
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Char
Dec
128
129
130
131
132
133
134
Hex
80
81
82
83
84
85
86
Char
á
í
ó
ú
ñ
Ñ
a
Dec
160
161
162
163
164
165
166
Hex
A0
A1
A2
A3
A4
A5
A6
Char
Dec
192
193
194
195
196
197
198
Hex
C0
C1
C2
C3
C4
C5
C6
Char
Ó
ß
Ô
Ò
õ
Õ
µ
Dec
224
Hex
E0
E1
E2
E3
E4
E5
E6
Ç
ü
é
â
ä
à
å
225
226
227
228
229
230
ã
ç
ê
è
è
ï
î
ì
Ä
Å
135
136
137
138
139
140
141
142
143
87
88
89
8A
8B
8C
8D
8E
8F
°
¿
®
167
168
169
170
171
172
173
174
175
A7
A8
A9
AA
AB
AC
AD
AE
AF
Ã
199
200
201
202
203
204
205
206
207
C7
C8
C9
CA
CB
CC
CD
CE
CF
p
p
231
232
233
234
235
236
237
238
239
E7
E8
E9
EA
EB
EC
ED
EE
EF
Ú
Û
Ù
´y
´Y
1/2
1/4
¡
–
É
Æ
Æ
144
145
146
90
91
92
176
177
178
B0
B1
B2
Ò
D
Ê
208
209
210
D0
D1
D2
240
241
242
F0
F1
F2
±
2
3
ô
147
93
179
B3
Ë
È
211
D3
3/4
243
F3
ö
ò
û
ù
ÿ
148
149
150
151
152
153
94
95
96
97
98
99
´
180
181
182
183
184
185
B4
B5
B6
B7
B8
B9
212
213
214
215
216
217
D4
D5
D6
D7
D8
D9
244
245
246
247
248
249
F4
F5
F6
F7
F8
F9
Á
Â
À
©
1
Í
Î
Ï
÷
¸
°
¨
Ö
Ü
Ø
£
Ø
x
154
155
156
157
158
159
9A
9B
9C
9D
9E
9F
186
187
188
189
190
191
BA
BB
BC
BD
BE
BF
218
219
220
221
222
223
DA
DB
DC
DD
DE
DF
·
250
251
252
253
254
255
FA
FB
FC
FD
FE
FF
»
¢
¥
Ì
ƒ
78
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
%
Available Fonts and Bar Codes
All character fonts and bar codes available with the printer are described in this
section. Each font and bar code has a name associated with it for use in
programming. Human-readable fonts have numeric names, while bar code fonts
have alpha names. Consult the Programmer's Manual for detailed information.
Fonts
Fonts 0 through 8 use the slash zero (Ø) convention for distinguishing between
the number zero and the letter O. The slash can be removed with the ‘Z’ label-
formatting command. These fonts are non-proportional (monospaced): each
character takes the same amount of space for printing.
The Triumvirate font number 9 is a proportional font: each character will take
up a different amount of space when printed.
Font
Valid ASCII Characters
0
1
2
3
32-127
32-168, 171, 172, 225
32-168, 171, 172, 225
32, 35-38, 40-58, 65-90, 128, 142-144, 146, 153, 154,
156, 157, 165, 168, 225
4
5
6
32, 35-38, 40-58, 65-90, 128, 142-144, 146, 153, 154,
156, 157, 165, 168, 225
32, 35-38, 40-58, 65-90, 128, 142-144, 146, 153, 154,
156, 157, 165, 168, 225
32, 35-38, 40-58, 65-90, 128, 142-144, 146, 153, 154,
156, 157, 165, 168, 225
7
8
9
32-126
32, 48-57, 60, 62, 67, 69, 78, 83, 84, 88, 90
32-126, 128-169, 171-173, 181-184, 189, 190, 198, 199, 208-216, 222, 224-
237, 241, 243, 246-250
J693
79
Download from Www.Somanuals.com. All Manuals Search And Download.
The table below lists the font sizes; the numbers indicate the number of dots.
Font
Height
7
13
18
27
36
52
64
32
Width
5
Spacing
Font 0
Font 1
Font 2
Font 3
Font 4
Font 5
Font 6
Font 7
Font 8
1
2
2
2
3
3
4
5
5
7
10
14
18
18
32
15
15
28
Font 0: 96-character alphanumeric,
Font 1: 145-character upper and
lower case alphanumeric
with descenders and
ascenders.
upper and lower case.
Font 2: 138-character alphanumeric, Font 3: 62-character alphanumeric,
upper and lower case. uppercase.
80
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Font 4: 62-character alphanumeric,
Font 5: 62-character alphanumeric,
uppercase.
uppercase.
Font 6: 62-character alphanumeric, uppercase.
J693
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Font 7: OCR-A, size I.
Font 8: OCR-B, size III.
Font 9: Internal Triumvirate font. The number in the bar code height field
sets the point sizes. Larger point sizes can be obtained by increasing
the height and width multipliers.
82
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar Code Summary Data
Bar Code fonts have alpha names (left column in the table below). Uppercase
alpha names will print barcodes with human-readable interpretations. Lowercase
alpha names will print barcodes only. The table is followed by visual samples.
Bar
Code
ID
Valid ASCII Characters,
Length Checksum decimal value
Type
Code 3 of 9
representation
A
Varies
11
No
32, 36, 37, 42, 43, 45-57,
65-90
48-57 Numeric only.
Option V used in the 6th &
7th position
B
UPC-A
Yes
C
D
E
F
UPC-E
6
Yes
No
48-57 Numeric only
48-57 Numeric only
Interleaved 2 of 5 (I 2 of 5) Varies
Code 128
EAN-13
Varies
12
M-103 32-127
Yes
48-57 Numeric only. Option
V used in the 7th & 8th
position
G
H
EAN-8
HBIC
7
Yes
M-43
48-57 Numeric only
32, 36-39, 42, 43, 45-57, 65-
90
Varies
I
J
Codabar
Varies
Varies
No
M-10
36, 43, 45-58, 65-68
48-57 Numeric only
Interleaved 2 of 5 with a
modulo 10 checksum
Plessey
K
L
Up to
14
M-10
M-10
48-57 Numeric only. Option
+ is Last Character for
Second M-11 Checksum
48-57 Numeric only
Interleaved 2 of 5 with a
modulo 10 checksum &
shipping bearer bars
2 digit UPC addendum
5 digit UPC addendum
Code 93
13
M
N
O
p
Q
R
2
5
Yes
Yes
No
Yes
Yes
Yes
48-57 Numeric only
48-57 Numeric only
35-38, 42-58, 65-90, 97-122
48-57 Numeric only
48-57 Numeric only
48-57 Numeric only
Varies
Varies
19
Postnet
UCC/EAN Code 128
UCC/EAN Code 128
K-Mart NON EDI barcode
UCC/EAN Code 128
Random Weight
Telepen
18
S
34 +
Yes
48-57 Numeric only
T
U
v
Varies
84
1
Yes
Yes
No
Alphanumeric
Alphanumeric
A, B, C, D
UPS MaxiCode
FIM
z
PDF-417
Varies
Varies
Varies
Varies
Yes
Yes
Yes
Yes
All
W1c DataMatrix
W1d QR Code – Auto format
W1D QR Code – Manual format
All 8-bit values
Alphanumeric
Single byte or Kanji double
byte
J693
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar Code A: Code 3 of 9
Bar Code B: UPC-A
Bar Code D: Interleaved 2 of 5
Bar Code C: UPC-E
Bar Code E: Code 128
Bar Code F: EAN-13
Bar Code H: Health Industry Bar
Code (HBIC)
Bar Code G: EAN-8
Bar Code I: Codabar
Bar Code J: Interleaved 2 of 5
w/module 10 checksum
84
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar Code K: Plessey
Bar Code L: Interleaved 2 of 5
w/module 10 checksum and
shipping bearer bars
Bar Code M: 2 Digit UPC addendum
Bar Code N: 5 Digit UPC addendum
Bar Code p: Postnet
Bar Code O: Code 93
Bar Code Q: UCC/EAN Code 128
Bar Code R: UCC/EAN Code 128
KMART NON EDI
J693
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar Code S: UCC/EAN Code 128 Random Weight
Bar Code T: Telepen
Bar Code u: UPS MaxiCode
Bar Code v: FIM
Bar Code z: PDF-417
Bar Code W1c: DataMatrix
Bar Code W1d: QR Code
86
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
&
Module Assignments
Memory Module
Designator Module Size Volatile*
Location / Use
A
B
Future Option
Future Option
1024 KB
N/A
N/A
Yes
N/A
N/A
Main PCB SDRAM – user
addressable for graphics, fonts, and
label formats
D
(default size)
F
4 MB
No
Optional Flash Card – user
addressable for graphics, fonts, and
label formats
Y
Z
64 KB
4 MB
No
No
Main PCB Flash – reserved for
EFIGS
Optional Flash Card – reserved for
ILPC
*When power is removed from the printer, stored data will be lost.
Print Resolutions and Maximum Widths
Resolutions and Widths
Maximum Print
Width
Factory Default
Model Printhead Resolution
Setting
Inches Millimeters
J693
203 dots/inch
(8 dots/mm)
4.09
103.9
4.10
J693
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Settings and Defaults
Consult the Programmer's Manual for detailed information.
J693
Speed Range
Default Setting
Function
IPS
MMPS
IPS
6.0
6.0
4.0
MMPS
152.4
152.4
101.6
2-8
2-10
2-4
50.8 – 203.2
50.8 – 203.2
50.8 – 101.6
Print
Feed
Reverse
88
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
'
Menu System Multi-Language Support
This printer provides the user with the ability to download new menu system
languages and/or replace the provided translations. A Microsoft
Excel
Spreadsheet defines the menu dictionary – the user adds a new language column
or modifies an existing column in the spreadsheet, clicks on the ‘Generate DPL
file(s)’ radio button and sends the generated DPL file(s) to the printer.
Here are the highlights and restrictions of the feature:
•
•
•
•
•
The printer can register up to 10 different display languages, including
EFIGS.
The EFIGS languages and any additional languages are stored on Module
Y: a 64KB Flash Module located on the Main PCB.
It is okay to download menu files generated for a lesser firmware revision to
new firmware – any messages that are not defined are displayed in English.
For the procedures below, the printer will accept the menu downloads from
any available port.
The language creation programs support Windows 95, Windows 98,
Windows NT, and Windows 2000.
Required Software
J693 Application Version 3.0 or
greater*
Comment
Must reside in the target printer. (See
Section 4.3.2 for details.)
Must be purchased by user.
Program used during the process to
create DPL file.
Microsoft Excel 97
Img2dl.exe**
Gemmsgxls.xls**
Menu Dictionary
*These software files and programs are available on our web site.
**Pitney Bowes recommends that the Img2dl.exe and Gemmsgxls.xls files reside in the
same directory.
J693
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a Menu Language:
1) Invoke Excel and open the gemmsglst.xls file. Excel opens the file and the
following screen appears.
2) Click the “Enable Macro” box and the following appears.
(Continued next page)
90
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Click On Column J and enter your new language, or modify an existing one.
Tips:
A) Message Size – When entering new messages, reference the ‘MAX’
column: this is the maximum number of characters allowed for this
field. Warnings are displayed when the number of characters is
exceeded or when trying to modify the MAX value. Beware that
“cutting” and “pasting” fields could defeat this warning system.
B) Two Line Messages – Some of the message are displayed as two lines.
These are indicated in the comment fields.
C) Comments – This field can be modified with no effect.
4) When editing has been completed, highlight all of the columns you desire to
create (more than one language may be selected) by pressing the letter
above the column.
5) Press the Generate DPL File(s) radio button. A
file will be generated for each of the selected
columns and Excel will provide confirmation.
(Example: small.ls)
(Continued next page)
J693
91
Download from Www.Somanuals.com. All Manuals Search And Download.
6) Download the generated files to the printer – one method is the DOS copy
command:
copy small.ls lpt1: /b
7) Reset the printer by pressing and holding the CANCEL key for
approximately four seconds.
8) Verify the operation by printing a Configuration Label (see Section 4.3.2).
The new font selection will be printed on the label under SYSTEM
INFORMATION / OPTIONAL LANGUAGES or select the new language
in the SYSTEM SETTINGS / MENU LANGUAGE in the printer’s menu.
This is the only method to determine whether the download was successful.
If the menu system displays the new language selection, but all displayed
messages remain in English an error has occurred. Re-check the process.
Contact Technical Support if problems continue and be prepared to provide
the Gemmsglst.xls and the DPL download file you have created. Other
possible error messages are as follows:
Menu Language Error Message
Description
Please select the entire column(s) After pressing the Generate DPL
or the desired language(s), by File(s) radio button, the languages
clicking on the column letter(s)
to convert were not correctly
selected.
Message text may not exceed The entered message exceeds the
MAX=xx designated characters for number of characters specified in
this MID
column C. You may not modify
this number.
Advance File Handling Information
The standard printer leaves the factory with EFIGS loaded into module Y.
At this point, Module Y is LOCKED and will only accept additional
Language Downloads.
After downloading a language update, Module Y is left UNLOCKED until
the printer is reset or power is cycled. In this state, Module Y will accept
font, image and label format downloads. The module will also honor the
Clear Module request. Therefore, following an update it is recommended
that a reset be performed to lock the module; otherwise, a software package
may ‘Clear All Modules’ thus destroying the new menu language(s).
Module Y can be UNLOCKED by sending this DPL string: <STX>KpY0.
(Continued next page)
92
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
To restore the factory generated EFIGS image, download the file
*832296.01A to the printer. This file is located on our web site. The letter at
the end of the file name (e.g., A) specifies the revision. The latest revision
will be available on the FTP site.
Downloading the same language twice will automatically delete the first
occurrence, but will not free the memory space. Use the Pack Module
feature (see Section 4.1.3) or reload the FIGS file to free the space.
Deletion of the selected language will set the printer to English.
The total number of languages that the printer can now accept is limited to
10, but this number is dependent upon the size of each language translation.
The translation size will vary with the number of messages that are
translated for that particular language. Current complete language files are
about 7,000 bytes each but with product growth, the total number of
languages is expected to drop to seven.
J693
93
Download from Www.Somanuals.com. All Manuals Search And Download.
94
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
alphanumeric Consisting of alphabetic, numeric, punctuation and
other symbols.
backing material The silicon-coated paper carrier material to which
labels with adhesive backing are affixed. Also referred to as
“liner”.
bar code A representation of alphanumeric information in a pattern of
machine-readable marks. The basic categories are divided into
one-dimensional (UPC, Code 39, Postnet, etc.) and two-
dimensional barcodes (Data Matrix, MaxiCode, PDF417, etc.).
boot loader The resident program that loads the application from
Flash memory, decompresses it into the SRAM, and starts
operations.
calibration The process through which sensor readings are entered into
the printer for correct sensor function (e.g., detection of a given
media) and TOF positioning.
character set The entire complement of alphanumeric symbols
contained in a given font.
checksum An alphanumeric error detection method used in many bar
code symbologies for informational security.
continuous media An uninterrupted roll or box of label or tag stock
media that contains no gap, notch, or mark to separate individual
labels or tags.
core diameter The inside diameter measurement of the cardboard core
at the center of a ribbon or media roll.
cutter A mechanical device (e.g., rotary or guillotine) used to cut labels
or tags following printing.
defaults The functional setting values returned following a factory
reset of the printer.
J693
95
Download from Www.Somanuals.com. All Manuals Search And Download.
diagnostics Programs used to locate and diagnose hardware problems.
die-cut media Media that has been cut into a pattern using a press,
where the excess paper is removed leaving individual labels,
with gaps between them, attached to a backing material.
direct thermal The printing method that uses a heat sensitive media
and only the heat of the thermal printhead to create an image on
the label.
direct thermal media Media coated with special chemicals that react
and darken with the application of heat.
DPI (dots per inch) A measurement of print resolution, rated in the
number of thermal elements contained in one inch of the
printhead. Also referred to as “resolution”.
DPL (Datamax Programming Language) programming commands
used specifically for control of and label production in the
printer. A complete listing of commands can be found in the
Programmer’s Manual.
EFIGS English, French, Italian, German, Spanish, and other multi-
language support as programmed for the printer’s menu system
and configuration label.
fan-fold Media that is folded and stacked.
feed speed The speed at which the media moves under the printhead in
non-printed areas and between labels.
Flash memory Non-volatile memory (does not require printer power to
maintain data) that can be erased and reprogrammed, used to
hold the printer’s operating program.
font A set of alphanumeric characters that share a particular typeface.
gap A space between die-cut or notched labels used to sense the top-of-
form.
IPS (inches per second) Imperial measurement of printer speeds.
label A paper or synthetic printing material, typically with a pressure
sensitive adhesive backing.
96
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
label length The distance from the top of the label to the bottom of the
label as it exits the printer.
label repeat The distance from the top of one label to the top of the
next label.
label tracking Undesirable lateral (side to side) movement of the
media as it travels under the printhead.
label width The left to right measurement of the label as it exits the
printer.
media Generalized term for all types of printing stocks, including: roll
fed, continuous, die-cut, and fanfold.
media hub Device in the printer used to support roll media.
media sensor An electronic device equipped with photosensors to
detect media and the top-of-form on die-cut, notched or
reflective media.
MMPS (millimeters per second) Metric measurement of printer
speeds.
notched stock Media, typically tag stock, with holes or notches in the
material that is used to signal the top-of-form. The printer must
be set to ‘gap’ to use this media type.
perforation small cuts extending through the label and backing
material to facilitate their separation. Also referred to as “perf”.
print speed The speed at which the media moves under the printhead
during the printing process.
reflective media Media imprinted with carbon-based black marks on
the underside of the material, which is used to signal the top-of-
form when the ‘reflective’ sensor is enabled.
registration Repeatable top to bottom alignment of printed labels.
reverse speed The backward rate of media motion into the printer
during tear-off, peel and present and cutting modes for
positioning the label at the start of print position.
J693
97
Download from Www.Somanuals.com. All Manuals Search And Download.
ribbon An extruded polyester tape with several layers of material, one
of which is ink-like, used to produce an image on the label. Also
referred to as “foil”.
ribbon wrinkle An undesirable overlapping of the ribbon during the
printing process that leads to voids on the printed label.
Typically caused by an improper printhead leveling cam
adjustment.
roll media A form of media that is wound upon a cardboard core.
start of print The position on the label where the printing actually
begins.
tag stock A heavy paper or synthetic printing material, typically
featuring a notch or black mark and without an adhesive
backing.
thermal transfer The printing method that creates an image by
transferring ink from a ribbon onto the media using the heat
from the thermal printhead.
TOF (top-of-form) The start of a new label.
void An undesirable blank space in a printed image.
98
J693
Download from Www.Somanuals.com. All Manuals Search And Download.
J693
99
Download from Www.Somanuals.com. All Manuals Search And Download.
|