Pelco Security Camera C401M C User Manual

C401M-C (12/99)  
EH1000  
Ceiling Enclosure  
®
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
3500 Pelco Way,  
Clovis, CA 93612-5699  
USA  
1. Installation and servicing should only be done by qualified service personnel and conform  
to all local codes.  
In North America & Canada:  
Tel (800) 289-9100  
FAX (800) 289-9150  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclo-  
sure, it is designed for indoor use only and it must not be installed where exposed to rain  
and moisture.  
International Customers:  
Tel +1 (559) 292-1981  
FAX +1 (559) 348-1120  
3. Only use replacement parts recommended by Pelco.  
The product and/or manual may bear the following marks:  
This symbol indicates that danger-  
ous voltage constituting a risk of  
electric shock is present within  
C A U T I O N :  
this unit.  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there  
are important operating and main-  
tenance instructions in the litera-  
ture accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation  
and operation.  
DESCRIPTION  
The EH1000 low-profile ceiling enclosure for 2/3-inch format cameras is designed to be mounted  
in fixed or dropped ceilings. The upper section mounted above the ceiling is constructed of alu-  
minum to meet most fire code requirements for installation in open plenum ceilings.  
The EH1000 is engineered for ease of installation and service. The lower section is hinged to  
provide convenient access for adjusting camera and lens. The upper section has generous  
interior dimensions which allow additional camera angle adjustments to be made.  
The EH1000 is equipped with a tamper-resistant lock for security protection. Cable entry is  
through conduit knockouts.  
INSTALLATION  
To mount the EH1000 directly into a fixed or dropped ceiling, perform the following steps:  
1. Determine the location and direction of the enclosure to be mounted. Ideally, the enclo-  
sure cutout should be parallel and adjacent, or perpendicular, to any ceiling structure.  
Avoid cutting into any ceiling structural members.  
2. Open the cover of the enclosure to expose the mounting holes in the flange.  
3. Remove any appropriate knockouts.  
4. Insert the enclosure into the opening and secure with the appropriate fasteners.  
5. Mount the camera and lens onto the adjustable mounting bracket. Adjust the position of  
the camera and lens to clear the enclosure cover when closed. Tighten the mounting  
bracket fasteners.  
NOTE: The camera mounting  
bracket is reversible, to accom-  
modate various camera and lens  
combinations.  
6. Route the appropriate cables into the enclosure. Make all necessary electrical connec-  
tions.  
7. Close and lock the cover.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 1. E1003 Ceiling Mounting Plate Installation  
17.10  
(43.43)  
9.70  
(24.64)  
10.50  
(26.67)  
4.56  
(11.58)  
15.00 (38.1)  
MAX. CAMERA LENGTH  
20.06  
(50.95)  
12.56  
(31.90)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;  
ALL OTHERS ARE IN INCHES.  
Figure 2. EH1000 Dimensions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY AND RETURN INFORMATION  
WARRANTY  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Pelco will repair or replace, without charge, any merchandise proved defective in material  
or workmanship for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
• Five years on FT/FR8000 Series fiber optic products.  
• Three years on Genex® Series products (multiplexers, server, and keyboard).  
• Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera  
models, which have a five-year warranty.  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
Method of return shipment shall be the same or equal to the method by which the item  
was received by Pelco.  
RETURNS  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
In order to expedite parts returned to the factory for repair or credit, please call the factory  
at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if  
returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
• Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and Endura™ Series distributed network-based video products.months on DX  
Series digital video recorders, NVR300 Series network video recorders, EnduraSeries  
distributed network-based video products, and TW3000 Series twisted pair transmission  
products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods  
to:  
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Service Department  
Pelco  
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or  
accident are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting  
from the specific use or application made of the Products. Pelco’s liability for any claim,  
whether based on breach of contract, negligence, infringement of any rights of any party  
or product liability, relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special, incidental or  
consequential damages (including loss of use, loss of profit and claims of third parties)  
however caused, whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also  
have additional rights, which are subject to variation from state to state.  
REVISION HISTORY  
Manual # Date  
Comments  
C401M  
8/87  
2/90  
Original version.  
C401M-A  
Manual revised to incorporate new manual style, UL information, and additional mounting plate installation information and  
dimension diagram.  
C401M-B  
C401M-C  
6/95  
12/99  
Noted camera mounting bracket is reversible. Put into new format.  
Revised to new format. Removed Figures 1 and 2.  
® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.  
™ Endura and ExSite are trademarks of Pelco.  
® Lucite is a registered trademark of Lucite  
© Copyright 1999, Pelco. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pentax VCR PV C78A User Manual
Petsafe Pet Fence UL 275 User Manual
Philips Bottle Warmer SCF613 20 User Manual
Philips CRT Television 14HT3154N User Manual
Philips Headphones SHE2643 User Manual
Philips Portable Speaker SBA220 00 User Manual
Philips Welding System TS2519C User Manual
Pioneer Stereo Receiver AVM P9000 User Manual
Planar Car Video System PL1911M User Manual
Pride Mobility Wheelchair INFMANU1206 User Manual