AUDIO/VIDEO
MULTI-CHANNEL RECEIVER
VSX-D938TX
VSX-D908TX-G
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL STEP SETTING (VSX-D908TX/ D908TX-G
only)
The unit has been factory preset to the channel allocation value for the area in which it is to be sold. If this value
is set incorrectly, the tunes in frequency may be wrong, or sound may be distorted, resulting in an inability to
reproduce reception signals at their proper sound quality. For this reason, be sure to confirm that the values are
set correctly before first using the unit.
FM 100 kHz, AM 10 kHz:
Set to this position for areas with an FM reception step of 100 kHz and AM 10 kHz.
FM 50 kHz, AM 9 kHz:
Set to this position, for areas with an FM reception step of 50 kHz and AM 9 kHz.
NOTE:
When unsure about the channel allocation for your area, consult your dealer for correct information.
To Change Channel Steps
With the power turned OFF, hold the STANDBY/ON button depressed while pressing the FM/AM function
button to turn the power ON.
• Each time the above operation is performed, the channel tuning step will alternate between FM 100 kHz/AM
10 kHz, and FM 50 kHz/AM 9 kHz.
STANDBY/ON
FM/AM
TWO VOLTAGE SELECTOR SWITCHES (VSX-D908TX/
D908TX-G only)
Mains voltages in Saudi Arabia are 127 V and 220 V only.
Never use this m odel w ith the 110 V setting in Saudi Arabia.
Medium-size screwdriver
TWO VOLTAGE SELECTORS
The line voltage selector switches are on the rear panel. Check that
they are set properly before plugging the power cord into the
household wall socket. If the voltage is not properly set or if you
move to an area where the voltage requirements differ, adjust the
220V
110V 120V-127V
110V 220V
240V
selector switches as follows.
120V-127V 240V
1. Use a medium-size screwdriver.
2. First, insert the screwdriver in the groove of the voltage selector
upper, and adjust so that the tip of the groove points to the
voltage value of your area.
3. Next, insert the screwdriver in the groove of the voltage
selector lower and adjust until the voltage is the same as at the
right.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
MPEG (Moving Picture Experts Group) decoder equipped
(VSX-D938TX only)
Playback of DVD and other media recorded in MPEG audio is possible.
The MPEG logo is a registered trademark of Royal Philips Electronics.
Decoding of Dolby Digital, Dolby Pro Logic and DTS (Digital Theater
R
System s)
DTS is the latest and most widely used digital theater system for cinemas throughout the world. The
decoder has been incorporated into this receiver and is able to achieve high sound quality as well as produce
dynamic surround sound effects. Also, there is no need to worry about program formats. When playing
Dolby Digital, Dolby Pro Logic or Dolby Surround software in the 2 (Dolby) Surround and HOME THX
CINEMA modes, decoding switches automatically according to the input signal, all you have to do is enjoy!
“DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc.
Manufactured under licence from Digital Theater Systems, Inc.
Manufactured under license from Dolby Laboratories. “Dolby”, “AC-3”, “Pro Logic”, and double-D
symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. © 1992 - 1997 Dolby
Laboratories, Inc. All rights reserved.
Direct Energy MOS Am plifier
This receiver incorporates 5 independent 110 watt (DIN) built in power amplifiers with high-performance Hex
power MOS FET output transistors. This construction provides improved linearity and accurate reproduction
of each channel for true high fidelity reproduction from even the most demanding Dolby Digital and DTS
program sources.
True Hom e Cinem a w ith THX® Certification
The HOME THX CINEMA surround mode employs special processing to allow you to enjoy movie
soundtracks with the same level of power and realism you experience in well designed movie theaters. You
can enjoy this effect with both Dolby Digital, Dolby Surround and DTS sources.
Manufactured under license from Lucasfilm Ltd. Lucasfilm and THX are trademarks of Lucasfilm Ltd.
Advanced Theater Modes
This mode enhances the sound of either film or music so a more dramatic effect can be achieved. The four
modes are each designed to accentuate specific sound qualities, giving the listener a wide range of
possibilities.
DSP Surround Modes
DSP (Digital Signal Processing) surround mode gives you the capability of transforming your living room into
six different sonic environments when listening to music.
Midnight Listening Mode
Midnight Listening mode allows you to obtain excellent surround sound effects even when listening at low
volumes, something that was previously impossible.
Digital Noise Reduction
Digital Noise Reduction is the latest technology for filtering out unwanted noise. It produces clear, resonant
tones.
Illum inated Rem ote Control of Other Com ponents
The supplied remote control can be used to operate a variety of other components simply by recalling the
appropriate preset codes or by using the learning function to teach the remote control new commands. In
addition, the multi-operation functions allow you to perform a variety of operations automatically.
The Energy-saving Design
This unit is designed to use minimal electricity when power is switched OFF (in Stanby mode). Regarding
the value of the power consumption in standby mode, refer to “Specifications” on pages 86-87.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Before You Start ........................................................................................... 6
Checking the Supplied Accessories ........................................................................ 6
How to Use This Manual .......................................................................................... 6
Opening the Front Panel .......................................................................................... 6
Preparing the Rem ote Control ................................................................................. 7
Connecting Your Equipm ent ....................................................................... 8
Audio Com ponents ................................................................................................... 8
Video Com ponents ................................................................................................... 9
Digital Connections ................................................................................................. 10
External Decoder Input ........................................................................................... 12
Antennas .................................................................................................................. 13
Speakers .................................................................................................................. 14
Connecting Additional Am plifiers ......................................................................... 17
Power Connections (AC OUTLETS) ....................................................................... 17
Displays and Controls ................................................................................ 18
Display ..................................................................................................................... 18
Front Panel (VSX-D938TX) ..................................................................................... 20
Front Panel (VSX-D908TX/D908TX-G) ................................................................... 22
Rem ote Control ....................................................................................................... 24
On Screen Display .................................................................................................. 26
Basic Playback ............................................................................................ 38
Playing Sources with Stereo Sound ...................................................................... 38
Selecting a Sound Mode ........................................................................................ 41
Switching ANALOG/DIGITAL signal input ............................................................ 44
Listening in MIDNIGHT LISTENING m ode ............................................................ 46
96kHz/24bit perform ance ........................................................................................ 47
Listening in LOUDNESS m ode (front panel only) ................................................ 48
Direct playback (front panel only) ......................................................................... 48
Using the Tuner .......................................................................................... 50
Autom atic and Manual Tuning .............................................................................. 50
Direct Access Tuning .............................................................................................. 51
Mem orizing Frequently Used Stations ................................................................. 52
Recalling Mem orized Stations ............................................................................... 53
Setting Up the Rem ote Control to Control Other Com ponents .......................... 54
Rem ote Controlling Other Com ponents ............................................................... 58
Recording from Audio Com ponents ..................................................................... 66
Recording from Digital Audio Com ponents ......................................................... 67
Recording from Video Com ponents ...................................................................... 68
Multi Operations ..................................................................................................... 69
Resetting the Rem ote Control ................................................................................ 74
Dolby Digital ............................................................................................................ 76
MPEG Audio ............................................................................................................ 78
Preset Code List ...................................................................................................... 79
Troubleshooting ...................................................................................................... 84
Specifications .......................................................................................................... 86
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Checking the Supplied Accessories
Please check that you have received all of the following supplied accessories.
FM w ire antenna
AM loop antenna
“AA” IEC LR6 batteries × 2
Rem ote control unit
How to Use This Manual
This manual is for the VSX-D938TX/D908TX/D908TX-G Audio/Video Multi-Channel Receiver.
This manual is divided into two main sections which will tell you how to setup and use the unit :
PREPARATION
First carry out the tasks below in this “Before You Start” section to prepare the remote control, then connect
the receiver to your other components as described in “Connecting Your Equipment” (p.8). Take special care to
connect your digital equipment like DVDs and LDs players properly to be able to take advantage of the receiver’s
surround sound systems.
To learn about a specific button, control, or indicator, see “Displays and Controls” starting on p.18.
SET UP
Performing the tasks in “Surround Sound Set Up” (p.27) is essential to get proper surround sound.
OPERATION
To play some music or soundtrack refer to “Basic Playback” on p.38. “Using the Tuner” (p.50) explains how to
use the radio of this unit. Doing the operations in “Remote Control of Other Components” (p.54) is highly
recommended so you can use this unit’s remote control for all your components. “Using Other Functions”
(p.66) explains the other possibilities of the receiver.
“Techno Tidbits & Problem-solving” (p.76) provides detailed technical information and a troubleshooting guide.
The following marks and symbols are used throughout the manual:
Provides additional information, precautions, and advice.
Indicates a blinking button, indicator, or display.
Indicates a steadily lit button, indicator, or display.
Opening the Front Panel
To open the front panel, push gently on the lower third of the panel with your finger.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Preparing the Rem ote Control
Loading the batteries
Load the batteries into the remote control as shown below. Please use alkaline batteries.
AA drycell batteries
(("AA" IEC LR6) × 2)
1
2
3
When you notice a decrease in the operating range of the remote control, replace all batteries with new ones.
CAUTION!
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following
precautions.
• Never use new and old batteries together.
• Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
• Batteries with the same shape may have different voltages. Do not use different batteries together.
Operating other PIONEER
com ponents
Operating range of rem ote
control unit
Connecting an optional control cord allows you to
operate other PIONEER components simply by
pointing the receiver’s remote control at the remote
sensor on the front panel of the receiver. The
receiver then sends the remote control signals to the
other devices via the CONTROL OUT terminal.
The area in which you can use the remote control to
operate the VSX-D938TX/D908TX/D908TX-G is fairly
large. To use, point the remote control toward the
remote sensor on the front panel of this unit while
within the range shown below.
Remote control may not function properly if:
• There are obstacles between the remote
control and the remote sensor.
• Direct sunlight or fluorescent light is
shining onto the remote sensor.
• The receiver located near a device
emitting infrared rays.
• You can also control PIONEER
components (and those made by other
manufactures) by pointing the receiver’s
remote control directly at the respective
component. This type of operation does
not require control cords. All you have to
do is recall the appropriate preset code
(see P.79 (VSX-D938TX), P.83 (VSX-
D908TX/D908TX-G)).
• Operated simultaneously with another
remote control which uses infrared rays.
• If you use a remote control hooked up via
the CONTROL IN jack with a control cord,
you will not be able to use this unit’s
remote control.
30°
30°
IN
CONTROL
CONTROL
OUT
IN
OUT
7 m
Receiver
PIONEER com ponent
bearing the Î m ark.
To CONTROL IN
term inal of another
PIONEER com ponent
bearing the Î m ark.
Rem ote Control
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Audio Com ponents
To begin set up, connect your audio components to the jacks as shown below. These are all analog connections
and your analog audio components (turntable, cassette deck) use these jacks. Remember that for components
you want to record with you need to hook up four plugs (a set of stereo ins and a set of stereo outs), but for
components that only play (like a turntable) you only need to hook up one set of stereo plugs (two plugs). To use
DTS surround sound features you must hook up your digital components to the digital inputs but it is also a good
idea to hook up your digital components to analog audio jacks. If you want to record to/from digital components
(like an MD) to/from analog components, you must hook up your digital equipment with these analog
connections. See p.10-11 for more on digital connections.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the wall outlet.
NOTE
• Only the VSX-D938TX has a 2 RF IN jack.
• The arrow s indicate the direction of the audio signal.
VSX-D938TX (Singaporean m odel)
R
L
VIDEO
AC OUTLETS
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
/MPEG OUT
PCM/ /DTS IN/MPEG IN
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
F
R
F
L
F
L
S
IN
IN
SWITCHED
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
REC PLAY
REC PLAY
OUTPUT
L
L
L
R
R
R
MD recorder
or Cassette deck
Cassette deck
(w ith REC m onitor)
CD player
Turntable
If your turntable has a
ground wire, connect it to
the SIGNAL GND terminal.
7 Audio cords
Use audio cords (not supplied) to connect the audio components.
R
Connect red plugs to R (right) and white plugs to L (left).
Be sure to insert completely.
L
Cassette deck placem ent
Depending on where the cassette deck is placed, noise may occur during playback of your cassette deck which
is caused by leakage flux from the transformer in the receiver. If you experience noise, move the cassette deck
farther away from the receiver.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Video Com ponents
Connect your video components to the jacks as shown below. Regarding digital video components (like a DVD),
you must use the analog connections pictured on this page for the video signal but in order to use Dolby Digital
you should hook up their audio to a digital input (see the next page). It is also a good idea to hook up your digital
components with analog audio connections as well (see the previous page). To cover all possible laser discs a
DVD/LD player or LD player requires an analog connection (as shown here) and two digital connections (see the
next page).
When connecting your equipment always make sure the power is turned off and the power cord is
disconnected from the wall outlet.
DVD player
(or LD player)
Video deck (2)
Video deck (1)
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
L
L
L
L
L
R
R
R
R
R
VSX-D938TX
(Singaporean
m odel)
R
L
VIDEO
AC OUTLETS
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
/MPEG OUT
PCM/ /DTS IN/MPEG IN
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
F
R
F
L
F
L
S
IN
IN
SWITCHED
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
OUT
MONITOR
TV
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
VIDEO
INPUT
VIDEO
OUTPUT
VIDEO
7 Front
5-CHANNEL EQUAL POWER OUTPUT
VIDEO INPUT
EXTERNAL
DECODER IN DIRECT
S-VIDEO
VIDEO
L
AUDIO
R
PHONES
SPEAKERS
L
Video
cam era
(etc.)
R
VIDEO INPUT
TV
(m onitor)
TV tuner
(or Satellite tuner)
V
L
R
Front video connections are accessed via the front
panel input selector as “VIDEO.”
7 Audio/ Video cords
If your video components have S-video
jacks, you could use S-video cords (not
supplied) to connect them on the back of
the receiver. These jacks are labeled by the
Japanese designation “S2” on the VSX-
D938TX/D908TX/D908TX-G but they are
simply S-video jacks.
Use audio/video cords (not supplied) to connect
the video components and a video cord to
connect the monitor TV.
Connect red
R
plugs to R (right),
L
white plugs to L
(left), and the
yellow plugs to
VIDEO.
Be sure to insert
completely.
VIDEO
However, if you use S-video cords for your
video hook ups you must also hook up your
TV with S-video connections. Conversely, if
you use regular composite video cords for
video hook ups, you should use them for
your TV as well.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Digital Connections
In order to use Dolby Digital/DTS soundtracks and MPEG audio, you need to make digital audio connections. You
can do this by either coaxial or optical connections (you do not need to do both). The quality of these two types
of connections is the same but since some digital components only have one type of digital terminal, it is a
matter of matching like with like (for example, the coaxial out from the component to coaxial in on the receiver).
The VSX-D938TX/D908TX/D908TX-G has two coaxial and two optical inputs for a total of four digital inputs. For
the VSX-D938TX, a DVD/LD player or LD player should be connected to a digital jack and the special AC-3 RF
jack (if the LD has one) as well as a pair of analog jacks (see the previous page). Connect your digital
components as shown below. There is one digital out jack which is marked PCM/2/DTS/MPEG(VSX-D938TX
only) OUT. If you connect this to the optical input on a digital recorder (currently these include MD, DAT and CD-
R) you can make direct digital recordings with this unit.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the wall outlet.
VSX-D938TX (Singaporean m odel)
R
L
VIDEO
AC OUTLETS
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
/MPEG OUT
PCM/ /DTS IN/MPEG IN
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
F
R
F
L
F
L
S
IN
IN
SWITCHED
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
DIGITAL OUT
OPT.
DIGITAL
OUT
DIGITAL
OUT
DIGITAL
IN
DIGITAL
OUT
TV tuner
(or Satellite tuner)
DVD player
CD player
MD recorder
7 Digital audio cords/ Optical cables
Commercially available digital audio coaxial cords (standard video cords can also be used) or optical cables
(not supplied) are used to connect digital components to this receiver.
When you use optical digital input or output terminals, pull off the caps and insert the plugs. Be sure to
insert completely.
Optical cable
Digital audio cord
(or standard video cord)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Exam ple of connection using a DVD/ LD or LD player
VSX-D938TX m odel:
Make sure you connect your DVD/LD or LD players using the AC-3 RF jack. If your player has an AC-3 RF output,
this will ensure you can use all types of laser discs. See p. 37.
VSX-D938TX (Singaporean m odel)
R
L
VIDEO
AC OUTLETS
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
/MPEG OUT
PCM/ /DTS IN/MPEG IN
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
F
R
F
L
F
L
S
IN
IN
SWITCHED
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
RF OUT
(AC-3)(LD)
Be sure to make either a digital coaxial
or digital optical connection (pictured as
DIGITAL jack 1 or DIGITAL jack 3 in this
diagram) as well, but you DO NOT need
to make both. Also, be sure to assign
the jacks to the proper component(s)
with the “Digital-In Select” procedure
(see p.37).
OUTPUT
VIDEO
DIGITAL OUT
PCM (OPT.)
1
2
L
3
R
DVD/ LD player
or LD player
VSX-D908TX/ D908TX-G m odels:
When playing LD recorded in Dolby Digital
To connect a DVD/LD or LD player with its AC-3 RF output, a commercially available RF demodulator (RFD-1) is
required. The RF demodulator changes the RF signal to a digital signal which is then processed by the VSX-
D908TX/D908TX-G models through their digital input jacks. For more details, refer to the instruction manual
supplied with the RFD-1.
VSX-D908TX/ D908TX-G
R
L
VIDEO
AC OUTLETS
DIGITAL
TWO VOLTAGE SELECTORS
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
OUT
PCM/ /DTS IN
TV/
SAT
IN
S
R
S
S
IN
S2
IN
PREOUT
L
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
220V
240V
F
F
L
F
L
S
IN
IN
R
110V 120V-127V
SWITCHED
TOTAL
VCR1
OUT
110V
220V
240V
100W MAX
F
R
S
120V-127V
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
RF OUT
(AC-3)(LD)
OUTPUT
VIDEO
DIGITAL OUT
PCM (OPT.)
Make sure the RF
demodulator
1
L
PCM/
(OPT.)
PCM/
PCM/
(OPT.)
PCM/
2
3
RF IN
(AC-3)(LD)
DIGITAL OUT
DIGITAL IN
digital in switch is
set correctly
R
(optical or coaxial
depending on the
connection).
DVD/ LD player
or LD player
DIGITAL IN
OPTICAL
COAXIAL
RF dem odulator RFD-1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
External Decoder Input
In some cases you may need an external decoder to play special analog or DVD sources. If you find you need an
external decoder hook one up as shown below, but for most people this component is unnecessary. (See p.47)
When connecting your equipment always make sure the power is turned off and the power cord is
disconnected from the wall outlet.
VSX-D938TX (Singaporean m odel)
R
L
VIDEO
AC OUTLETS
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
/MPEG OUT
PCM/ /DTS IN/MPEG IN
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
F
R
F
L
F
L
S
IN
IN
SWITCHED
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
»
»
»
»
SURROUND
OUTPUT
FRONT
OUTPUT
SUB
W OOFER
CENTER
L
R
L
R
Com ponents equipped w ith 5.1
channel analog output jacks
You cannot use the tuner and phono
functions with an external decoder input.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Antennas
Hook up the supplied radio antennas as shown below. When connecting your equipment, always make sure the
power is turned off and the power cord is disconnected from the wall outlet.
AM loop antenna
FM w ire antenna
Connect the FM w ire antenna and fully extend to the “T” shape.
(For best reception, attach horizontally along a w indow fram e, etc.)
(See below )
VSX-D938TX (Singaporean m odel)
R
L
VIDEO
AC OUTLETS
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
/MPEG OUT
PCM/ /DTS IN/MPEG IN
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
FM
F
R
F
L
F
L
S
IN
IN
SWITCHED
ANTENNA
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
FM
P
L
S
L
UNBAL
S
IN
IN
75Ω
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
AM LOOP
ANTENNA
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
7 AM loop antenna
1 Assemble the antenna.
2 Twist exposed wire strands
3 Attach to a wall, etc. (if
desired) and face toward the
direction providing the best
reception.
together and insert.
10 mm
Using external antennas
7 To im prove AM reception
7 To im prove FM reception
Connect a 5~6 meter length of vinyl-coated wire to the AM
antenna terminal in addition to the supplied AM loop
antenna.
Connect an external FM antenna.
For the best possible reception, suspend horizontally
outdoors.
Outdoor antenna
75 Ω coaxial cable
FM
ANTENNA
PAL
FM UNBAL
75Ω
connector
FM UNBAL
75Ω
FM
FM
ANTENNA
UNBAL
75Ω
FM
5~6 m
ANTENNA
Indoor antenna
(Vinyl-coated
w ire)
AM LOOP
ANTENNA
AM LOOP
ANTENNA
GND
GND
AM LOOP
ANTENNA
(Singaporean
m odel only)
(Others)
ground
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Speakers
A full complement of six speakers is shown here but, naturally, everyone’s home set up will vary. Simply
connect the speakers you have in the manner described below. The VSX-D938TX/D908TX/D908TX-G will work
with just two stereo speakers (called “front” speakers in the diagram) but the receiver is designed to be used
with at least three speakers.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left
terminal. Also make sure the positive and negative (+/–) terminals on the receiver match those on the speakers.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the wall outlet.
The VSX-D938TX/D908TX/D908TX-G has two speaker systems, A & B. A is the main system supporting
the full complement of surround sound speakers. If you switch on both A & B speaker systems, only
front speakers and the sub-woofer will be audible. No sound will come from the center or surround
speakers but multi channel sources will be down-mixed to the active speakers so no sound will be lost.
Similarly, if you choose just the B system, you will only hear the front speakers connected to the B
system and multi channel sources will be down-mixed to these two speakers.
Front Speakers (A)
Center Speaker
C
Rear Speakers
SR SL
L
R
VSX-D938TX
(Singaporean
m odel)
R
L
VIDEO
AC OUTLETS
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
PCM/ /DTS IN/MPEG IN
/MPEG OUT
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
F
R
F
L
F
L
S
IN
IN
SWITCHED
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
Pow ered sub w oofer
INPUT
Be sure to com plete all other
connections before connecting
this unit to the AC pow er source.
When using the speaker on your TV as the center speaker, connect the
CENTER PREOUT jack on this unit to the audio input jack on your TV. In this
case, the center speaker show n is unnecessary.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
7 Speaker term inals
1 Twist exposed wire
2 Loosen speaker
terminal and insert
exposed wire.
3 Tighten terminal.
strands together.
10 m m
Speaker im pedance
You can change the speaker impedance to suit the kind of speakers you have in your home system but we
recommend using speakers with an impedance of 8 Ω-16 Ω (the default setting). If you are using 6 Ω-less than
8Ω impedance speakers, you need to change the impedance setting.
w STANDBY/ON
First turn the receiver off, then press the pow er button
w hile holding dow n the SPEAKERS button.
VSX-D938TX
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
Digital S
Choose the impedance setting by pressing the SPEAKERS button again.
STANDBY/ ON
DSP
MODE
STANDBY
STEREO
You can choose the 8 Ω-16 Ω setting or the 6 Ω-8 Ω setting.
/
DTS
THX CINEMA ADVANCED
STANDARD
MPEG
SIGNAL
SELECT
ANALOG SP
VOLUME
A
(This display indicates an 6 Ω-less than
8 Ω impedance setting)
dB
5
-CHANNEL EQUAL POWER OUTPUT
VIDEO INPUT
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDN
S-VIDEO
VIDEO
L
AUDIO
R
PHONES
SPEAKERS
–
BASS
+
–
To check which impedance the amplifier is set to hold down
the SPEAKERS button for 2-3 seconds. You willl get a display
like the one shown below right telling you the speaker
impedance setting.
SPEAKERS
SIGNAL
SELECT
ANALOG SP
SIGNAL
SELECT
ANALOG SP
VOLUME
VOLUME
A
A
dB
dB
or
(This display indicates a 6 Ω-less
than 8 Ω impedance setting)
(This display indicates an 8 Ω-16 Ω
impedance setting)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Speaker placem ent
If you have a multiple speaker arrangement the placement of the speakers is extremely important. To achieve
the best possible surround sound, install your speakers as shown below. Make sure all speakers are installed
securely to prevent accidents and improve sound quality. Be sure to consult your speaker manuals for the best
placement of the speakers. Some speakers are designed to be floor-standing but others benefit greatly from
speakers stands which raise them off the floor.
Front
Left
Front
Right
Center
Sub
Woofer
Surround
Right
Surround
Listening
Position
Left
• Install the left and right front speakers at equal distances from the TV.
• When installing speakers near the TV, we recommend using magnetically shielded speakers to
prevent possible interference such as distortion in the color of the TV screen. If you do not have
magnetically shielded speakers and notice discoloration of the TV screen, place the speakers farther
away from the TV.
• Install the center speaker above or below the TV so that the sound of the center channel is localized
at the TV screen.
CAUTION:
When installing the center speaker on top of the TV, be sure to secure it with tape or some other
suitable means. Otherwise, the speaker may fall from the TV due to external shocks such as
earthquakes, and it may lead to endangering those nearby or damaging the speaker.
• If possible, install the surround speakers slightly above ear level.
• It may be difficult to obtain a cohesive surround effect if the surround speakers are installed farther
away from the listening position than the front and center speakers.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Equipm ent
Connecting Additional Am plifiers
Although the VSX-D938TX/D908TX/D908TX-G has more than sufficient power for any home use, it is possible to
add additional amplifiers to your system. If you want to use separate amplifiers to power your speakers, make
the connections shown below.
When connecting your equipment always make sure the power is turned off and the power cord is
disconnected from the wall outlet for all the eqiuipment.
PIONEER
projection TV
(for center
channel)
Pow ered
sub w oofer
Am plifier
(for center
channel)
Am plifier
(for surround
channels)
Am plifier
(for front
channels)
L-Audio
(MONO)
AUDIO
IN
AUDIO
IN
AUDIO
IN
AUDIO
IN
INPUT
(or)
L
L
L
L
R
R
R
R
VSX-D938TX
(Singaporean
m odel)
AC OUTLETS
R
L
VIDEO
DIGITAL
DVD
/LD
IN
CAUTION:
DO NOT
CONNECT
TV SET OR
MONITOR.
S
IN
1
2
3
4
PCM/ /DTS
/MPEG OUT
PCM/ /DTS IN/MPEG IN
PREOUT
TV/
SAT
IN
S
R
S
L
S
IN
S2
IN
EXTERNAL
DECODER
IN
UNSWITCHED
100W MAX
RF IN
F
F
L
F
L
S
IN
IN
R
SWITCHED
TOTAL 100W MAX
VCR1
OUT
F
R
S
S
W
C
OUT
P
L
S
L
S
IN
IN
A
Y
TAPE2
MONITOR
VCR2
OUT
R
E
C
S
R
S
FR
FL
C
SR
SL
R
L
TO
MONITOR
TV
OUT
P
L
I
N
S
VIDEO
OUT
CD
C
A
Y
OUT
MD/
TAPE1
R
L
R
E
C
S
W
IN
CONTROL
OUT
IN
A
B
FRONT
SPEAKERS
CENTER
SURROUND
SPEAKERS
FRONT
SPEAKERS
SPEAKERS
PHONO
SEE INSTRUCTION MANUAL
Pow er Connections (AC OUTLETS)
[SWITCHED TOTAL 100 W MAX]
Power supplied through these outlets is turned on and off by the receiver’s POWER switch. Total electrical
power consumption of connected equipment should not exceed 100 W.
[UNSWITCHED 100 W MAX]
Power flows continually to this outlet, regardless of whether the receiver is switched ON or OFF. Electrical
power consumption of the connected equipment should not exceed 100 W.
SWITCHED
UNSWITCHED
100W MAX
TOTAL 100W MAX
UNSWITCHED
100W MAX
SWITCHED
TOTAL 100W MAX
AC OUTLETS
Others
Taiw anese m odel only
CAUTION!
• To avoid overheating, fire risk, and possible malfunction do not connect high-wattage appliances such as
heaters, irons, monitors, or TV sets to the AC OUTLETS.
• Remove the power plug from the wall socket to disconnect this unit from the AC power source when not
in regular use, for example, when on vacation.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
Display
All the display information is explained and/or referenced here.
2
3
4 56
7
8
9
0
SIGNAL ATT LOUDNESS MIDNIGHT DSP
SELECT
STEREO
VOLUME
PRO LOGIC
OVER
ANALOG SP AB
H.P
1
DIGITAL
DIGITAL
AC-3 RF MONO STEREO
AUTO TUNED AMFM
dB
MPEG
TAPE 2
AC-3 DTS MPEG
L
C
R
LFE
LS
RS
S
!
@
-
=
~
H.P
SP AB
1 SIGNAL SELECT indicators
3 LOUDNESS indicator (See p.48)
Light to indicate the type of input signal assigned
for the current component (see “Front Panel”, %
(VSX-D938TX), $ (VSX-D908TX/D908TX-G),
SIGNAL SELECT).
ANALOG : Lights when an analog signal is
selected.
DIGITAL : Lights when a digital audio signal is
selected (DVD/LD, CD, MD/TAPE1, TV/SAT,
VCR 1, VCR 2).
Lights when the LOUDNESS mode is on.
4 MIDNIGHT indicator (See p.46)
Lights when the MIDNIGHT LISTENING mode is
on.
5 Radio Frequency/ Function indicator
Displays the function or the frequency of the
current radio station.
AC-3 RF: Lights when an AC-3 RF signal is
selected (DVD/LD, TV/SAT, VCR 1, VCR 2). (VSX-
D938TX only)
AUTO: Lights when the receiver is set to select
the input signal automatically. (DVD/LD, CD, MD/
TAPE 1, TV/SAT, VCR 1, VCR 2). (VSX-D938TX
only)
AC-3 : Lights when a source with Dolby Digital
signals is played.
DTS : Lights when a source with DTS audio
signals is played.
6 DSP indicator (See p.40-41)
Light when a DSP or Advanced Theater mode is
selected.
7 STEREO indicator (See p.40-41)
Lights when a STEREO mode is selected.
8 2 Surround/ dts m ode indicators
2 DIGITAL : When the 2 Surround/dts mode
on the receiver is on, this indicator lights to
indicate playback of a Dolby Digital signal.
However, 2 PRO LOGIC lights during 2 channel
playback of Dolby Digital.
MPEG: Blinks when the MPEG mode is selected,
and lights when a source with MPEG audio
signals is played. (VSX-D938TX only)
2 PRO LOGIC : When the 2 Surround/dts
mode on the receiver is on, this indicator lights
during 2 channel playback. ( Both B or A+B
speaker systems turn off automatically when
headphones are plugged in.)
DTS : Lights when DTS signals are input.
MPEG: Lights when MPEG signals are input.
(Dolby/DTS/MPEG mode is ON). (VSX-D938TX
only)
2 Analog level indicators
OVER : If “ANALOG” is selected in SIGNAL
SELECT, this indicator lights to show that an
excessively strong signal is being processed.
When this occurs, press INPUT ATT on the front
panel to attenuate (lower) the signal. Also, when
“DIGITAL” is selected in SIGNAL SELECT, this
indicator lights to show that a source containing
an excessive amount of information is being
processed. If this occurs, see p. 41.
9 MASTER VOLUME indication
ATT : Lights when INPUT ATT is used to reduce
the level of the input signal (available in ANALOG
mode only).
Displays current level of master volume.
0 TAPE 2 indicator
Lights when the TAPE 2 monitor is on.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
- Program Form at indicator
When a Dolby Digital or DTS signal is input, he
following indicators light to show the channels
being played back.
L : Left front*1*2, C : Center*1, R : Right front*1*2,
LS : Left surround*1, S : Surround (mono)*2,
RS : Right surround*1
*1: Indicates 5.1ch Dolby Digital or DTS playback.
*2: Indicates Dolby Pro Logic playback.
= Tuner indicators
MONO : Lights when the tuner is set to receive
FM broadcasts and when selected MPX mode.
STEREO : Lights when a FM stereo broadcast is
received in the auto stereo mode.
TUNED : Lights when a broadcast is received.
AM/ FM : Light to indicate the current band (FM
or AM).
~ Character display
Displays sound modes, general information, etc.
! Speaker indicators
Light to indicate the current speaker system (see
“Front Panel”, ¡ (VSX-D938TX), + (VSX-
D908TX/D908TX-G), SPEAKERS (A/B)).
SP # A : Lights when speaker system A is
selected.
SP # B : Lights when speaker system B is
selected.
SP # AB : Lights when speaker systems A and B
are both selected.
@ H.P (headphones) indicator
Lights when headphones are connected to the
PHONES jack (speakers A and B turn off
automatically).
# LFE indicator
LFE (Low Frequency Effects) indicator lights to
indicate that the program source contains an LFE
channel. The indicator under the LFE lights during
actual playback of the LFE signals (LFE signals
are not present in all parts of the soundtrack).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
Front Panel (VSX-D938TX)
All the controls on the front panel are explained and/or referenced here. To open the front panel, push gently on
the lower third of the panel.
1 2 3 4 5 6
7
8 9
0
-
=
VSX-D938TX
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
INPUT
SELECTOR
STANDBY/ ON
DSP
TAPE
2
STANDBY
MODE
STEREO
MONITOR
/
DTS
FL
DIMMER
THX CINEMA ADVANCED
STANDARD
MPEG
MASTER
VOLUME
DOWN
UP
~ ! @ # $ %
^
TUNER CONTROL
5 -CHANNEL EQUAL POWER OUTPUT
VIDEO INPUT
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
NR
SIGNAL
SELECT
CLASS
FM/ AM
–
TUNING
+
S-VIDEO
VIDEO
L
AUDIO
R
PHONES
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
MPX
MEMORY
–
STATION
+
£
™
¡
+
_
)
( *
&
1 Main Pow er Sw itch (— OFF, _ ON)
STANDBY/ ON button
7 Display (See page 18)
2
8 Rem ote sensor
Press to switch the receiver ON or into STANDBY
mode.
Point the remote control toward the remote
sensor to operate the receiver.
3 STANDBY indicator
9 TAPE 2 MONITOR button (See p.66)
Lights when the receiver is in STANDBY mode.
(Please note that this receiver consumes a small
amount of power (1.0 W) during the standby
mode.)
Selects the tape deck (MD recorder, etc.)
connected to the TAPE 2 MOINTOR inputs/
outputs. Allows monitoring of a recording as it is
being made.
4 DSP MODE button (See p.40-41)
0 FL DIMMER button (See p.49)
Press repeatedly to select a DSP sound mode.
(HALL 1, HALL 2, JAZZ, DANCE, THEATER 1, or
THEATER 2). Use these modes to produce
surround sound from standard (two channel)
stereo sources and create different listening
environments.
Use to adjust the brightness of the main display.
- INPUT SELECTOR dial
Turn to select a source component. The source
indicators show the current component:
DVD/ LD : DVD player or Laser Disc player.
TV/ SAT : TV tuner or satellite tuner.
CD : Compact Disc player.
5 STEREO button (See p.40-41)
Press to select the STEREO sound mode. In this
mode, sound comes from the front (left and right)
speakers only.
MD/ TAPE 1 : Tape deck or Mini Disc recorder
connected to MD/TAPE 1 inputs/outputs.
TUNER : The built-in tuner.
PHONO : Turntable.
VIDEO : Video camera (etc.) connected to the
VIDEO INPUT on the front panel.
VCR 1 : Video cassette recorder connected to
VCR 1 inputs.
VCR 2 : Video cassette recorder or other
component connected to VCR 2 inputs.
6 2/ DTS buttons (See p. 39, 41 and 76-
78)
THX CINEMA: Press to select the HOME THX
CINEMA sound mode when listening to Dolby
Digital, Dolby Pro Logic or DTS a variety of other
sources.
ADVANCED THEATER : Press to select one of
the four Advanced Theater modes.
STANDARD (MPEG) : Press to select the
STANDARD/MPEG mode.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
= MASTER VOLUME
) INPUT ATT button
Adjusts the overall receiver volume.
Use to lower the input level of an analog signal
that is too powerful, thus causing the receiver to
distort (the overload indicator will light furiously).
~ EXTERNAL DECODER IN (See p.47)
Use to hook up an external component that can
decode other types of signals and input them into
the VSX-D938TX.
_ TREBLE (–/ +) buttons (See p.48)
Use to adjust the high frequencies.
! DIRECT button
+ BASS (–/ +) buttons (See p.48)
Switches DIRECT playback on or off. Use to
bypass the tone controls and channel level for the
most accurate reproduction of a program source.
It will automatically put the receiver in STEREO
mode for the function being used for DIRECT
playback.
Use to adjust low frequencies.
¡ SPEAKERS (A/ B) buttons
A is the primary setting. It plays all speakers
hooked up to the A system. A and B setting only
plays the front speakers of both the A and B
systems and the sub-woofer, multi channel
sources will be down-mixed to these speakers so
no sound will be lost. B setting only plays the
front speakers connected to the B system and
multi channel sources will be down-mixed to
these two speakers.
@ LOUDNESS button (See p.48)
Switches the LOUDNESS mode on or off.
# MIDNIGHT button (See p.46)
Switches the MIDNIGHT LISTENING mode on or
off.
A
B
A+B
OFF
$ DIGITAL NR button (See p.45)
Switches the DIGITAL NR on or off (STEREO
mode only).
™ VIDEO INPUT jacks (See p.9)
% SIGNAL SELECT button (See p.42)
S-VIDEO : Video input for connecting a video
camera (etc.), that has an S-Video out.
VIDEO / AUDIO (L/ R) : Video input for
connecting a video camera, etc. that has standard
video/audio outputs.
Use to select the signal from the digital
components.
SIGNAL SELECT repeatedly to select one of the
following:
ANALOG : To select an analog signal.
DIGITAL : To select a optical or electrical digital
signal.
AC-3 RF: To select an AC-3 RF signal.
AUTO: This is the default. If there are both
analog and digital input signals, the receiver
automatically selects the digital signal.
£ PHONES jack
Connect headphones for private listening (no
sound will be heard through the speakers).
^ TUNER CONTROL button (See p.50-53)
CLASS : Press repeatedly to switch the preset
station classes.
FM/ AM : Press to select the AM or FM band.
TUNING –/ + : Use to manually tune to radio
stations.
& STATION –/ + buttons (See p.52-53)
Use to choose programmed radio stations.
* MEMORY button (See p.52)
Press to start the memorization of a preset
station.
( MPX button (See p.50)
Press to switch between auto stereo and MONO
reception of FM broadcasts. When the broadcast
signal is weak, selecting MONO will improve the
sound quality.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
Front Panel (VSX-D908TX/ D908TX-G)
All the controls on the front panel are explained and/or referenced here. To open the front panel, push gently on
the lower third of the panel.
1
2 3 4 5
6
7 8
9
0
-
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
INPUT
SELECTOR
STANDBY/ ON
TAPE
2
DSP
MODE
STANDBY
STEREO
MONITOR
/
DTS
FL
DIMMER
THX CINEMA ADVANCED
STANDARD
MASTER
VOLUME
DOWN
UP
= ~ ! @ # $
%
TUNER CONTROL
5 -CHANNEL EQUAL POWER OUTPUT
VIDEO INPUT
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
NR
SIGNAL
SELECT
CLASS
FM/ AM
–
TUNING
+
S-VIDEO
VIDEO
L
AUDIO
R
PHONES
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
MPX
MEMORY
–
STATION
+
™
¡
+
_
)
(
* &
^
1
STANDBY/ ON button
6 Display (See p.18)
Press to switch the receiver ON or into STANDBY
mode.
7 Rem ote sensor
Point the remote control toward the remote
sensor to operate the receiver.
2 STANDBY indicator
Lights when the receiver is in STANDBY mode.
(Please note that this receiver consumes a small
amount of power (1.0 W) during the standby
mode.)
8 TAPE 2 MONITOR button (See p.66)
Selects the tape deck (MD recorder, etc.)
connected to the TAPE 2 MOINTOR inputs/
outputs. Allows monitoring of a recording as it is
being made.
3 DSP MODE button (See p.40-41)
Press repeatedly to select a DSP sound mode.
(HALL 1, HALL 2, JAZZ, DANCE, THEATER 1, or
THEATER 2). Use these modes to produce
surround sound from standard (two channel)
stereo sources and create different listening
environments.
9 FL DIMMER button (See p.49)
Use to adjust the brightness of the main display.
0 INPUT SELECTOR dial
Turn to select a source component. The source
indicators show the current component:
DVD/ LD : DVD player or Laser Disc player.
TV/ SAT : TV tuner or satellite tuner.
CD : Compact Disc player.
MD/ TAPE 1 : Tape deck or Mini Disc recorder
connected to MD/TAPE 1 inputs/outputs.
TUNER : The built-in tuner.
4 STEREO button (See p.40-41)
Press to select the STEREO sound mode. In this
mode, sound comes from the front (left and right)
speakers only.
5 2/ DTS buttons (See p. 39, 41 and 76-
78)
PHONO : Turntable.
VIDEO : Video camera (etc.) connected to the
VIDEO INPUT on the front panel.
VCR 1 : Video cassette recorder connected to
VCR 1 inputs.
VCR 2 : Video cassette recorder or other
component connected to VCR 2 inputs.
THX CINEMA: Press to select the HOME THX
CINEMA sound mode when listening to Dolby
Digital, Dolby Pro Logic or DTS a variety of other
sources.
ADVANCED THEATER : Press to select one of
the four Advanced Theater modes.
STANDARD : Press for pure decoding of multi
channel sources.
- MASTER VOLUME
Adjusts the overall receiver volume.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
= EXTERNAL DECODER IN button (See
_ BASS (–/ +) buttons (See p.48)
p.47)
Use to adjust low frequencies.
Use to hook up an external component that can
decode other types of signals and input them into
the VSX-D908TX/D908TX-G.
+ SPEAKERS (A/ B) buttons
A is the primary setting. It plays all speakers
hooked up to the A system. A and B setting only
plays the front speakers of both the A and B
systems and the sub-woofer, multi channel
sources will be down-mixed to these speakers so
no sound will be lost. B setting only plays the
front speakers connected to the B system and
multi channel sources will be down-mixed to
these two speakers.
~ DIRECT button
Switches direct playback on or off. Use to bypass
the tone controls and channel level for the most
accurate reproduction of a program source. It will
automatically put the receiver in STEREO mode
for that function being used for DIRECT playback.
! LOUDNESS button (See p.48)
A
B
A+B
OFF
Switches the LOUDNESS mode on or off.
@ MIDNIGHT MODE button (See p.46)
Switches the MIDNIGHT LISTENING mode on or
off.
¡ VIDEO INPUT jacks (See p.9)
S-VIDEO : Video input for connecting a video
camera (etc.), that has an S-Video out.
VIDEO / AUDIO (L/ R) : Video input for
connecting a video camera, etc. that has standard
video/audio outputs.
# DIGITAL NR button (See p.45)
Switches the DIGITAL NR on or off (STEREO
mode only).
$ SIGNAL SELECT button (See p.42)
™ PHONES jack
Use to select the signal from the digital
components.
SIGNAL SELECT repeatedly to select one of the
following:
Connect headphones for private listening (no
sound will be heard through the speakers)
ANALOG : To select an analog signal.
DIGITAL : To select a optical or electrical digital
signal.
% TUNER CONTROL button (See p.50-53)
CLASS : Press repeatedly to switch the preset
station classes.
FM/ AM : Press to select the AM or FM band.
TUNING –/ + : Use to manually tune to radio
stations.
^ STATION –/ + buttons (See p.52-53)
Use to choose programmed radio stations.
& MEMORY button (See p.52)
Press to start the memorization of a preset
station.
* MPX button (See p.50)
Press to switch between auto stereo and MONO
reception of FM broadcasts. When the broadcast
signal is weak, selecting MONO will improve the
sound quality.
( INPUT ATT button
Use to lower the input level of an analog signal
that is too powerful, thus causing the receiver to
distort (the overload indicator will light furiously).
) TREBLE (–/ +) buttons (See p.48)
Use to adjust the high frequencies.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
Rem ote Control
These pages describe the buttons on the remote
control used to operate the receiver.
1
SOURCE button (See p.58-65)
Use to turn on the power of your other
components after you have recalled or taught the
signals to this remote control.
- =
2 MULTI CONTROL buttons
Use these to select a source and the
corresponding remote operation mode.
For example, pressing TUNER selects the built in
tuner and sets the remote operation to the tuner
functions.
Î
RECEIVER
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
1
2
~
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
3 Com ponent Control buttons
¶
-
3
-
8
+
TUNING
STATION
+
¡
Use to control specific components, like a CD
player or DVD player, after you have programmed
the remote control to do these operations (see
p.58-65) and the remote is put in that operation
mode.
3
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
!
@
7
4 TV CONTROL buttons
The following buttons are used to control the TV
only and can be used no matter what function the
remote control is set to.
TV : Press to turn the power of the TV on/off.
TV FUNC : Press TV FUNC to select the TV for
remote control operation.
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
4
5
#
TV FUNC
TV VOL +/ – : Press to control the volume of the
TV.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
$
%
6
7
5 MENU button
Use to get the various menus for this unit onto
your TV or DTV screen.
SIGNAL
SELECT
^
&
*
(
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
8
9
0
6 EFFECT/ CH SEL +/ – buttons (See p.41)
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
EFFECT : Use these buttons to increase or
decrease the amount of effect applied in a DSP or
Advanced Theater mode. When the amount of
effect is increased in a DSP/Advanced Theater
mode the characteristics of that mode become
stronger and more noticeable. The scale ranges
from 10-90 with 70 as the default setting. First
turn on the DSP/Advanced Theater you want (by
pressing the DSP/Advanced Theater button until
you get the mode) and then increase or decrease
the amount of effect.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
CH SEL : You may want to adjust the channels
when listening to some sound sources. Use this
button to select the channel you want to adjust.
+/ – : Use these buttons to select the amount of
effect in a sound mode and to adjust the channel
level when making surround sound settings.
7 5/ ∞/ 2/ 3/ ENTER buttons
Use to operate the on-screen menu on your TV
screen and enter commands when setting up
surround sound, speakers levels & settings, and
other set up features see p.27-37). Specific use
of these buttons is described in conjunction with
the operations they perform. For more
information, see each individual section.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Displays and Controls
8 SYSTEM SETUP button
^ SIGNAL SELECT button
Use to set up the speaker and sound systems.
For more information, see “Surround Sound
Setup” on p. 26.
Press SIGNAL SELECT repeatedly to select one
of the following:
ANALOG : To select an analog signal.
DIGITAL : To select a digital signal (DVD/LD,
TV/SAT, CD, MD/TAPE 1, VCR 1, VCR 2).
AC-3 RF: To select an AC-3 RF signal (DVD/LD,
TV/SAT, VCR 1, VCR 2). (VSX-D938TX only)
AUTO: This is the default. If there are both
analog and digital input signal, the receiver
automatically selects the best possible signal.
Press the SIGNAL SELECT and REMOTE SETUP
buttons simultaneously to switch from the
SIGNAL SELECT operation to EXTERNAL
DECODER operation.
Then press the button to get the EXTERNAL
DECODER function. To get back to the SIGNAL
SELECT control, press the REMOTE SETUP
button and the SIGNAL SELECT button
simultaneously once again. (VSX-D938TX only)
9 REMOTE SETUP button.
Use to customize the remote control functions
and the remote control itself. (See “Setting Up
the Remote Control to Control Other
Components” on p.54, “Multi Operation” on p.
69.)
To access the EXTERNAL DECODER option,
press the REMOTE SETUP button and the
SIGNAL SELECT button simultaneously.
0 MIDNIGHT button (See p. 46)
Switches the MIDNIGHT LISTENING mode on or
off.
- MULTI OPERATION button
Use this button to start the MULTI OPERATION
mode. See p. 69 for how to program and use the
MULTI OPERATION mode.
& 2/ dts/ MPEG (VSX-D938TX only)
buttons (See p.41)
Press these buttons to put the receiver in the
selected sound mode. For more information on
the modes .
= SYSTEM OFF button
This button turns off components in two ways.
First, when pressed it will turn off all PIONEER
components. Secondly, any component that has
programmed into the MULTI OPERATIONS
settings will also be turned off. (see p.69).
* STEREO/ DIGITAL NR button
STEREO : Press this button to put the receiver
into stereo mode when it is in a different sound
mode. For more information on the sound
modes, see p.41.
DIGITAL NR : Switches the DIGITAL NR on or off
(see p.44).
For exam ple : If you programmed power off in
the SYSTEM OFF settings for your TV and VCR,
pressing the SYSTEM OFF button will turn off
these components even if they are not PIONEER
products.
( DSP button (See p.41)
Press repeatedly to select a DSP sound mode.
~
RECEIVER button
Press to turn power of the receiver on or to
STANDBY (off).
! Num ber buttons
These buttons can perform a variety of different
functions depending on the remote operation
mode. They are most useful for CD and tuner
operations.
@ DISC/ DISPLAY button
These buttons can perform a variety of different
functions depending on the remote operation
mode.
# MASTER VOLUME button
Use to raise or lower the volume of the receiver.
$ MUTE button
Press to mute or restore the volume.
% FUNCTION button
Press to select a source. The button will cycle
through all the possible sources.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
On Screen Display
There are a number of possible ways to hook up the receiver to your video components like a DVD player and
hook up to your receiver to your TV, but some of them will not allow you to use the on-screen display of this
unit. To avoid this one simply needs to follow two rules.
1 Always use the same type of video cords to hook up your video components to the receiver as you use to
hook up the receiver and your TV. For example, if you use composite video cords to hook up your DVD and
the receiver, use composite video cords to hook up the receiver to your TV. If you use S video cords to hook
up your DVD and the receiver, use S video cords to hook up the receiver to your TV.
2 Always make sure your TV is set to the appropriate input channel on your TV (for example, video 1). Your TV
may have a number of input channels and if you do not select the proper one you will not be able to use this
receiver’s on-screen display. If you are unsure how to choose an input channel for your TV, refer to the
manual which came with your TV.
You might, for example, use both composite and S video cords to hook up your video component with this
receiver and then use composite video cords to hook up this receiver to your TV. This arrangement would still
NOT let you see the on screen displays from this receiver on your TV. The best idea is just to use one type of
video cord for all your video component and TV hook ups.
Sw itching video system betw een PAL and NTSC
This receiver is able to use two types of video systems for its OSD (on screen display) and you need to set the
receiver to the type of video system you have, either PAL or NTSC. If you do not match the system on the
receiver with your home system no OSD will appear on your TV. People with multi-system TVs, don’t need to
worry about changing the setting. If necessary, follow the instructions below to switch the type of video
system.
wSTANDBY/ON
1 Put the receiver in STANDBY m ode.
LOUDNESS
VSX-D938TX
2 While holding dow n the LOUDNESS button press the
STANDBY/ ON button. The video system type, either
”PAL“ on ”NTSC,“ appears in the display. It w ill be
show n for about seven seconds and then the receiver
reverts to norm al operating m ode.
Be careful to press the LOUDNESS button and NOT the DIRECT
button, which will accidentally clear all your speaker settings (see
warning p.29-30).
when a PAL system is
selected
SIGNAL
SELECT
VOLUME
SP
A
DIGITAL
dB
when a NTSC system is
selected
SIGNAL
SELECT
VOLUME
SP
A
DIGITAL
dB
When using the PAL setting the OSD does not get displayed in
color.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Setting Up for Surround Sound
To ensure the best possible surround sound, be sure to complete the following set up operations. This is
particularly important when using the DTS, 2 (Dolby) Surround sound and MPEG (VSX-D938TX only) modes.
You only need to make these settings once (unless you change the placement of your current speaker system
or add new speakers, etc.). These set up operations use your TV to display the settings and choices so be sure
your TV and receiver are properly hooked up.
Î
RECEIVER
1 Turn on the receiver and your TV.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
Make sure your TV is set to the receiver.
1
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
2 Press SYSTEM SETUP button.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
The SYSTEM SETUP MENU appears on your TV screen.
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
2
5
8
0
3
1
System Setup
[Speaker Setting]
[Channel Delay]
6
9
4
7
[Channel Level]
+1 0
DISC
DISPLAY
[Crossover Network]
[Bass Peak Level Manager]
[D-Range Control]
[Digital-In Select]
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
A
dB
AUTO
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
2
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
* You can escape from this screen at any time by pressing the
SYSTEM SETUP button again. None of the settings you made will
be entered in this case.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Î
RECEIVER
3 Press the 5 or ∞ arrow buttons to m ove the cursor to
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
the m ode you w ant. Then press ENTER.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
In each mode, the current settings are displayed automatically. We
suggest you adjust all these settings when you first hook up the
receiver. That gets them out of the way and you will not need to
return to this setting mode unless you change your home set up by
adding new speakers (etc.). The sound set up modes explained
here are:
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
Speaker Setting (See p.29-30)
Use to specify the type and number of speakers you connected.
7
+1 0
DISC
DISPLAY
RF ATT
Channel Delay (See p.31)
TV
TV CONTROL
Set up all your speakers for the most realistic surround sound.
Adding a slight delay to some speakers enhances sound separation
and is particularly important for achieving a surround sound effect.
You need to figure out the distance from your listening position to
your speakers to add the proper delay.
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
3
Channel Level (See p.32-33)
Use to balance the volumes of your different speakers.
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
Crossover Netw ork (See p.34)
DIGITAL NR
This feature lets you select which bass frequencies will be sent to
the sub woofer or front speakers.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
Bass Peak Level Manager (See p.35)
Dolby Digital and DTS audio sources include ultra-low bass tones.
Set the bass peak level as needed to prevent the ultra-low bass
tones from distorting the sound from the speakers.
VSX-D938TX
D-Range Control (See p.36)
This feature makes possible excellent surround sound effects
when listening to Dolby Digital sources at low volumes.
Digital-In Select (See p.37)
In order to use your digital components, you must match the
numbered digital input buttons with the numbered digital jacks
used by your digital components.
4 Go on to the next page to continue set up.
To exit the SYSTEM SETUP MENU and on-screen display press
SYSTEM SETUP button again.
After you complete one of the SYSTEM SETUP menus and
return to the basic SYSTEM SETUP screen (shown in the
diagram directly above labeled 4), the receiver automatically
moves the cursor to the next SYSTEM SETUP menu. For
example, if you’ve completed SPEAKER SETTING and returned
to the basic SYSTEM SETUP screen, CHANNEL DELAY will be
selected automatically. You can notice this on your TV screen.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Speaker setting
The following steps show you how to specify the type of speakers you connected. Use the 5¥∞ and 2¥3 arrow
buttons to make a selection within the on-screen menus, and use the ENTER to register the information.
Î
S0 URCE
RECEIVER
1 Select SPEAKER SETTING w ith the 5¥∞ buttons.
MULTI
SYSTEM
OFF
OPERATION
See “Setting Up for Surround Sound” on page 27 if you are unsure
how to do this.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
4
-
8
+
Press ENTER.
TUNING
STATION
+
¡
1
¢
CHANNEL
+
2
5
8
0
3
1
Speaker Setting
6
9
4
[FREE]
[THX]
7
Front
L
[LARGE]
+1 0
DISC
DISPLAY
Center
Surround
Subwoofer
[LARGE]
[LARGE]
[ YES ]
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
[EXIT]
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
2 Select a speaker setting m ode w ith the 2¥3 buttons.
1,2
SIGNAL
SELECT
2/ dts
Press the ∞ button.
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
Speaker Setting
[FREE]
[THX]
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
Front
L
[LARGE]
Center
Surround
Subwoofer
[LARGE]
[LARGE]
[ YES ]
VSX-D938TX
[EXIT]
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Î
S0 URCE
RECEIVER
3 Specify the type of speakers you connected. See the
explanations below for the m eaning of each size.
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
1 Press 2 or 3 to move the cursor to LARGE, SMALL, or NO
(you cannot select NO for the FRONT speakers).
2 Press ∞.
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
4
-
8
+
TUNING
STATION
+
¡
1
¢
CHANNEL
+
3 Repeat 1 and 2 for each speaker.
2
5
8
0
3
1
Depending on your choices the sound w ill be routed
differently, as explained here.
6
9
4
7
+1 0
DISC
DISPLAY
FRONT (default setting is LARGE)
RF ATT
• Select small to send bass frequencies to the sub woofer.
• Select large if your speakers will reproduce bass frequencies
effectively or if you did not connect a sub woofer.
(If you select small for the front speakers the sub woofer will
automatically be switched YES. Also,the center and surround
speakers cannot be set to large if the front speakers are set to
small. In this case, all bass frequencies are sent to the sub
woofer.)
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
3,4
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
CENTER (default setting is LARGE)
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
• Select large if your speaker will reproduce bass frequencies
effectively.
• Select small to send bass frequencies to the other speakers or
sub woofer.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
• If you did not connect a center speaker, deselect it. In this case,
the center channel is output from the front speakers.
VSX-D938TX
SURROUND (default setting is LARGE)
• Select large if your speakers will reproduce bass frequencies
effectively.
• Select small to send bass frequencies to the other speakers or
sub woofer.
• If you did not connect surround speakers, deselect them. In this
case, the sound of the surround channels is output from the front
and center speakers.
SUB WOOFER (default setting is YES)
• Leave it selected if you connected a sub woofer.
• If you did not connect a sub woofer, deselect it. In this case, the
bass frequencies are output from the front or surround speakers.
• Choose the PLUS setting if you want stronger reproduction of
deep bass sounds.
• If you select PLUS the bass frequencies that would normally
come out the front and center speakers are all routed to the sub
woofer.
4 Select EXIT w ith the 5¥∞ buttons and press ENTER to
return to the SYSTEM SETUP MENU.
Next, proceed to CHANNEL DELAY below.
If you w ant to change a setting before proceeding
Simply use the arrow buttons to go back.
If you have a sub woofer and like lots of bass, it may seem logical to select LARGE for your FRONT
speakers and leave the sub woofer selected. This may not, however, yield the best bass results.
Depending on the size and shape of your room, you may actually experience a decrease in the amount
of bass due to what is called “low frequency cancellations.” If you have a sub woofer, listen to the bass
response with the FRONT speakers set to LARGE and SMALL alternatively and let your ears judge
which sounds best.
The safest option in this case is to route all the bass sounds to the sub woofer by selecting SMALL for
the FRONT speakers.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Channel delay
Adding a slight delay to some speakers is necessary to achieve a surround sound effect. You need to figure out
the distance from your listening position to your speakers to add the proper delay. The following steps show you
how to set the delay time for each channel by specifying the distances from your listening position to each
speaker. Once you specify the speaker distances, the receiver calculates the correct delay times automatically.
If continuing from SPEAKER SETTING, go to step 1. If starting fresh, complete steps 1-3 in “Setting Up for
Surround Sound” (p.27) first.
Î
S0 URCE
RECEIVER
1 Select CHANNEL DELAY (if continuing from last set
up, it w ill already be selected).
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
See “Setting Up for Surround Sound” on page 27 if you are unsure
how to do this.
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
Press ENTER.
2
5
8
0
3
1
6
9
4
Channel Delay
7
L
[3.0m]
[3.0m]
[3.0m]
[3.0m]
[3.0m]
[3.0m]
Front
Center
Front
L
+1 0
DISC
DISPLAY
RF ATT
R
R
L
Surround
Surround
Subwoofer
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
[EXIT]
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
1-3
SIGNAL
SELECT
The default setting is 3.0 m.
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
2 Use the 5¥∞ buttons to select a speaker. Specify the
distance from your listening position to each speaker
using the com m ands below .
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
1 Press 2 or 3 to adjust the speaker distance in 0.3 m.
increments from 0.3 to 9.0 m.
2 Use the 5¥∞ buttons to move to the next set of speakers
3 Repeat for each speaker.
VSX-D938TX
NOTE : Sound takes about 1 ms (millisecond) to travel 0.3 m.
3 Select EXIT w ith the 5¥∞ buttons and press ENTER to
return to the SYSTEM SETUP MENU.
Next, proceed to CHANNEL LEVEL below.
If you w ant to change a setting before proceeding
Simply use the arrow buttons to go back.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Channel level
The following steps show you how to balance the sound output level of your speakers. Proper speaker balance
is essential for obtaining high quality surround sound. If continuing from CHANNEL DELAY, go to step 1. If
starting fresh, complete steps 1-3 in “Setting Up for Surround Sound” (p.27) first.
Î
S0 URCE
RECEIVER
1 Select CHANNEL LEVEL (if continuing from CHANNEL
DELAY, it w ill already be selected).
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
See “Setting Up for Surround Sound” on page 27 if you are unsure
how to do this.
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
Press ENTER.
2
5
8
0
3
1
6
9
4
Channel Level
7
Test Tone
[Setting Start
[ AUTO ]
]
+1 0
DISC
DISPLAY
RF ATT
[EXIT]
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
1,2
SIGNAL
SELECT
2 Select aTEST TONE m ode.
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
1 Press 2 or 3 to move the cursor to AUTO or MANU.
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
2 Press ∞ button to select SETTING START.
DIGITAL NR
AUTO (autom atic TEST TONE)
This mode switches the test tone between each speaker
automatically. Use this mode when balancing the speaker levels by
ear.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
The automatic test tone is output in the following order:
VSX-D938TX
FL
CT
SL
FR
SR
SW
MANUAL (m anual TEST TONE)
This mode switches the test tone between each speaker manually.
You can use this mode when you want to balance the speaker
levels by ear at a more leisurely pace.
If your sub woofer has a volume control, set it to the middle
position before proceeding.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Î
S0 URCE
RECEIVER
3 After selecting SETTING START w ith the button press
ENTER. The TEST TONE w ill be output.
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
These settings will be displayed on your TV.
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
Channel Level
2
5
8
0
3
1
Test Tone
[Setting OK
[ AUTO ]
]
6
9
4
Front
Center
Front
L
L
[ 0dB]
[ 0dB]
[ 0dB]
[ 0dB]
[ 0dB]
[ 0dB]
7
+1 0
DISC
DISPLAY
RF ATT
R
Surround
Surround
Subwoofer
R
TV
TV CONTROL
L
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
A
dB
AUTO
3,4
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
It takes a moment for the machine to set itself. MASTER VOLUME
rotates to the reference position (0 dB), and the test tone is output.
DIGITAL NR
To exit before outputting the TEST TONE
Press ENTER.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
To exit w hile outputting the TEST TONE
Press ENTER.
VSX-D938TX
4 Adjust speaker levels so that you hear the test tone at
the sam e volum e from each speaker w hen seated in
your m ain listening position.
NOTE : The volume of the sub woofer tends to sound lower than it
actually is, you may need to raise its level after testing the sound
with actual soundtracks.
In AUTO m ode
It is possible to set
channels levels
1 Press 2 or 3 to adjust the level of the speaker outputting the
TEST TONE.
independently for 2
Surround/dts, STEREO,
EXTERNAL DECODER and
each DSP mode for
listening once purposes
(see p.24 6).
This function is designed
to be used when you want
to change the levels
temporarily to hear one
speaker louder.
In MANU m ode
1 Press 2 or 3 to adjust the level of the first speaker.
2 Press 5¥∞ to switch the TEST TONE to the next speaker.
3 Repeat 1 and 2 for each speaker.
If you are using a Sound Pressure Level (SPL) m eter
Take the readings from your main listening position and adjust the
level of each speaker to 75 dB SPL (C-weighted/slow model).
5 When you have adjusted each speaker level, select
SETTING OK and press ENTER to return to the
previous screen.
You sould return the
settings to their original
state when done.
The MASTER VOLUME will return to its original position.
Next, proceed to CROSSOVER NETWORK below.
If you w ant to change a setting before proceeding.
Simply use the arrow buttons to go back.
6 Select EXIT w ith the 5¥∞ buttons and press ENTER to
return to the SYSTEM SETUP MENU.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Crossover netw ork
The following steps show you how to adjust the crossover network. The crossover network is the frequency at
which the system divides the signal and sends the different parts (high ,mid, low) to different speakers.
Speaking precisely, this setting sets the cutoff point for the bass frequencies rerouted from your SMALL
speakers to your sub woofer or speakers set to LARGE. If continuing from CHANNEL LEVEL go to step 1. If
starting fresh, complete steps 1-3 in “Setting Up for Surround Sound” (p.27) first.
Î
S0 URCE
RECEIVER
1 Select CROSSOVER NETWORK (if continuing from
CHANNEL LEVEL, it w ill already be selected).
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
See “Setting Up for Surround Sound” on page 27 if you are unsure
how to do this.
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
Press ENTER.
CHANNEL
-
+
2
5
8
0
3
1
Crossover Network
6
9
4
Frequency [ 80Hz]
7
+1 0
DISC
DISPLAY
(THX Speaker = 80Hz)
[EXIT]
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
1-3
The default setting is 80 Hz.
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
2 Specify the crossover frequency for your sm all
speakers.
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
Setting speakers to SMALL in “SPEAKER SETTING” sends the
respective channel’s bass frequencies to the sub woofer (or LARGE
speakers). The present function lets you determine which
frequencies will be sent to the sub woofer or LARGE speakers.
1 Press 2 or 3 to move the cursor to 80 Hz, 100 Hz, or
150 Hz.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
2 Press ∞.
80 Hz
Sends bass frequencies below 80 Hz to the sub woofer (or LARGE
speakers).
100 Hz
Sends bass frequencies below 100 Hz to the sub woofer (or
LARGE speakers).
150 Hz
Sends bass frequencies below 150 Hz to the sub woofer (or
LARGE speakers).
As noted on your TV screen the THX setting is 80 Hz. Select this
setting if you have THX approved SMALL speakers.
Experiment with the different settings to see which sounds best to
you.
3 Select EXIT to return to the SYSTEM SETUP MENU.
Next, proceed to BASS PEAK LEVEL MANAGER below.
If you w ant to change a setting before proceeding
Select a new crossover frequency.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Bass peak level m anager
The LFE (Low Frequency Effect) channel in Dolby Digital, DTS and MPEG audio (VSX-D938TX only) program
sources can produce heavily concentrated ultra-low bass tones that may exceed the capabilities of your speaker
system. The following steps show you how to set the peak level for the ultra-low bass (LFE) channel. If
continuing from CROSSOVER NETWORK go to step 1. If starting fresh, complete steps 1-3 in “Setting Up for
Surround Sound” (p.27) first.
Î
S0 URCE
RECEIVER
1 Select BASS PEAK LEVEL MANAGER (if continuing
from CROSSOVER NETWORK it w ill already be
selected).
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
1
3
-
8
+
See “Setting Up for Surround Sound” on page 27 if you are unsure
how to do this.
TUNING
STATION
+
¡
4
¢
CHANNEL
-
+
2
5
8
0
3
1
Press ENTER.
6
9
4
7
Bass Peak Level Manager
+1 0
DISC
DISPLAY
[Setting Start
]
RF ATT
[Setting Cancel]
TV
TV CONTROL
TV VOL
VOLUME
[EXIT]
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
1-4
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
2 Select SETTING START and press ENTER.
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
MASTER VOLUME rotates to MIN (---dB). Then the test tone is
output to the sub woofer or front or surround speakers.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
Bass Peak Manager
[Setting OK
]
VSX-D938TX
Bass Peak Level
[-50]
3 Press and hold the 3 until you hear the test tone from
the sub w oofer and specify the peak LFE level.
Use the 2 or 3 arrows to gradually increase the level of the LFE
channel until the test tone begins to distort. Then go back and
leave the level setting at a point just before that. Press ENTER and
the receiver will remember this bass output level.
To exit before outputting the TEST TONE
Press ENTER.
To exit w hile outputting the TEST TONE
Press ENTER.
4 Press ENTER to return to the previous screen.
This completes the speaker setup.
If you select SETTING CANCEL and press ENTER, no settings
are input to the receiver but the screen remains on the TV. To
escape the screen, you must press EXIT.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
D-range control
This feature makes it possible to enjoy full surround sound effects on Dolby Digital sources even at low
volumes. It does this by compressing the dynamic range. Dynamic range is the difference between the loudest
and the softest sounds in any given signal. Compressing the range plays sounds so the quieter ones are audible
and the louder ones don’t get distorted or become overpowering. This feature only applies to Dolby Digital
sources but the MIDNIGHT LISTENING mode accomplishes the same end for a variety of sources (see p.46). If
continuing from BASS PEAK LEVEL MANAGER, go to step 1. If starting fresh, complete steps 1-3 in “Setting
Up for Surround Sound” (p.27) first.
Î
S0 URCE
RECEIVER
1 Select D-RANGE CONTROL (if continuing from BASS
PEAK LEVEL MANAGER, it w ill already be selected).
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
See “Setting Up for Surround Sound” on page 27 if you are unsure
how to do this.
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
Press ENTER.
2
5
8
0
3
1
6
9
4
Dynamic Range Control
Select Mode [OFF]
7
+1 0
DISC
DISPLAY
RF ATT
(For Dolby Digital)
[EXIT]
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
1-3
SIGNAL
SELECT
• The default setting is OFF.
• If listening at loud volumes, we recommend turning the
Dynamic Range Control OFF.
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
2 Use the 2 or 3 to choose OFF, MID or MAX.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
3 Select EXIT and press ENTER to return to the SYSTEM
SETUP MENU.
VSX-D938TX
If you w ant to change a setting before proceeding
Choose a new DYNAMIC RANGE CONTROL setting.
You may need to experiment with different Dolby Digital sources
before you can use the DYNAMIC RANGE CONTROL setting to
suit your low volume listening needs.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround Sound Set Up
Digital-in select
In order to be able to use your digital equipment properly, you need to assign digital inputs for each of the digital
components you connected. Match the Digital 1-4 setting with the digital jacks1-4 in accordance with what
component is hooked up to each digital jack. Check the digital terminal numbers on the back of the receiver to
make certain what component is in which jack (if necessary, see p.10 for more on digital connections). The last
setting, the AC-3 RF button, is specifically for a DVD/LD or LD player with an AC-3 RF output. If you connected
one of these components match this button to the component. If continuing from BASS PEAK LEVEL
MANAGER, go to step 1. If starting fresh, complete steps 1-3 in “Setting Up for Surround Sound” (p.27) first.
Î
S0 URCE
RECEIVER
1 Select DIGITAL IN SELELCT(If continuing from last set
up, it w ill already be selected).
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
See “Setting Up for Surround Sound” on page 27 if you are unsure
how to do this.
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
Press ENTER.
CHANNEL
-
+
2
5
8
0
3
1
Digital In Select
6
9
4
Digital-1
Digital-2
Digital-3
Digital-4
AC-3 RF
[DVD/LD]
7
[
[
CD
MD
]
]
+1 0
DISC
DISPLAY
RF ATT
[TV/SAT ]
[DVD/LD]
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
[EXIT] L
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
1-3
Only the VSX-D938TX has an AC-3 RF terminal. See the note on
p.11 for other models’ AC-3 RF hook up.
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
2 Choose a DIGITAL IN and assign it an input function.
Use the 2 or 3 to choose the input function that m atches the
com ponent hooked up to that digital term inal.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
The possible choices include: DVD/LD,TV/SAT, CD, MD/TAPE 1,
VCR 1,VCR 2. You cannot assign digital inputs to the TUNER,
VIDEO, PHONO, and TAPE 2/MONITOR functions.
VSX-D938TX
3 Select EXIT and press ENTER to return to the SYSTEM
SETUP MENU.
If you w ant to change a setting before proceeding
Simply use the arrow buttons to go back.
• For the Digital 1-4 setting, you can choose between DVD/LD,
CD, TV/SAT, MD/TAPE 1,VCR 1 and VCR 2 functions.
• For the AC-3 RF setting, you can choose between DVD/LD,
TV/SAT, VCR 1 and VCR 2 functions.
Remember, if you have a DVD/LD or LD player you should
hook it up to the analog and digital jacks in addition to the AC-
3 RF connection described here.
• Once one function (for example DVD/LD) has been assigned
its name disappears from the possibilities on the remaining
buttons because one function cannot be assigned twice.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Playing Sources w ith Stereo Sound
The following instructions show you how to play audio or audio-visual stereo sources with the VSX-D938TX/
D908TX/D908TX-G.
Î
RECEIVER
1 Turn on the pow er of the playback com ponent.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
2
3
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 Press the RECEIVER button to turn
on the receiver.
MULTI CONTROL
STANDBY
indicator
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
Be sure that the standby indicator turns off
on the front panel.
VSX-D938TX
1
4
¢
CHANNEL
-
+
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
2
5
8
0
3
1
STANDBY/ ON
DSP
MODE
STANDBY
STEREO
6
9
4
/
DTS
THX CINEMA ADVANCED
STANDARD
MPEG
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
3 Press MULTI CONTROL buttons or the FUNCTION
button on the rem ote control or turn the INPUT
SELECTOR dial on the front panel to select the source
you w ant to playback.
TV VOL
VOLUME
6
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
The FUNCTION button cycles through the sources in the following
order:
3
4
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
DVD/LD
VCR 2
TV/SAT
VCR 1
CD
MD/TAPE 1
TUNER
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
VIDEO PHONO
DIGITAL NR
4 Press SIGNAL SELECT on the rem ote control or on the
front panel to select the input signal corresponding to
the source com ponent.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
(See “Switching ANALOG/DIGITAL signal input” on p. 40.)
5 Start playback of the com ponent you selected in step
1.
3
2
VSX-D938TX
6 Adjust the volum e by using the MASTER VOLUME
buttons on the rem ote control or the MASTER
VOLUME on the front panel.
If you are not able to get sound from the receiver, the problem
may well lie with the SIGNAL SELECT switch. You need to
make sure the input is set to the appropriate ANALOG or
DIGITAL setting. Refer to page 44 for more on this.
4
6
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Sound Modes
The six sound modes on the VSX-D938TX (The five sound modes on the VSX-D908TX/D908TX-G) are explained
here. These can be turned on from the front panel or from the remote control.
There are four (VSX-D938TX) or three (VSX-D908TX/D908TX-G) cinema modes: STANDARD, MPEG (VSX-
D938TX only), HOME THX CINEMA, and ADVANCED THEATER. These are designed to be used with multi
channel surround sound audio/visual sources (like DVDs and LDs). Intrinsic to home theater, these modes can
deliver realistic and powerful surround sound that recreates the movie theater experience. You may need to
experiment with them to see which settings suit your home system and personal tastes.
The DSP and STEREO modes are designed to be used with music sources but some DSP modes are also suited
for film soundtracks. Again, try different settings with various soundtracks to see which you like.
You must choose one of the three cinema modes or the DSP mode in order to get surround sound. In STEREO
mode, only the front two speakers are used.
STANDARD m ode
This mode is for pure decoding of Dolby Digital, DTS and Dolby Pro Logic. No special effects are added. It is
good for enjoying movies that have been recorded in Dolby Digital, DTS or Surround.
HOME THX CINEMA m ode
THX is a set of technical standards created by Lucasfilm, Ltd. These standards were designed to emulate a film
sound stage and thus reproduce, with the greatest possible accuracy, the soundtrack intended by the
filmmakers.
For more detailed information, see P.78.
MPEG m ode (VSX-D938TX only)
Use this mode to enjoy playback of software recorded in MPEG audio.
ADVANCED THEATER m odes
The Advanced Theater mode is a newly designed system for enhancing movie soundtracks and other audio-
visual sources. It incorporates the use of DTS (Digital Theater System) as well as Dolby Digital into its sound
processing. These functions switch on automatically when the source you are playing is encoded with DTS,
Dolby Pro Logic or Dolby Digital (bearing the
logo). There are four Advanced Theater settings that use
1
DSP (Digital Signal Processing) to create different types of sound environments.
MUSICAL
This mode is primarily for music and adds a spacious feeling to the sound. A long delay time of reflected
sounds, provides resonant tones which emulate a concert hall.
DRAMA (CINEMA)
This mode is designed for movies with a lot of dialog. The elements of dialog are enhanced, making the
characters seem more real. The mode also compresses the dynamic range somewhat so loud sounds do not
overpower softer ones (compare this with the MIDNIGHT LISTENING mode explained on p.46).
ACTION
This mode is designed for action movies, which generally use lots of sound effects. The mode enriches the
sound to make it more realistic and extends the parameters to pick up high and low sound effects.
5-D THEATER
This mode is especially designed to give sound depth to stereo sources. The overall effect builds a dynamic
and broad sound space, allowing two-channel (stereo) signals to faithfully imitate a five speaker sound. The
mode should be used in conjunction with Dolby Pro Logic for sources bearing the 3 mark.
When a Dolby Digital soundtrack is played back, the Dialog Normalization function of the receiver
activates automatically. Dialog Normalization is a Dolby Digital function that establishes the average
dialog level for the program source being played. If the receiver’s level does not match the average
dialog level, first you see “DIAL. NORM” flash in the receiver’s display and next OFFSET + 4 dB (as an
example) will appear. The number +4 dB is the difference between the receiver’s gain structure and the
Dolby Digital average dialog level. To match the average dialog level, subtract or add the OFFSET level.
Fleovreel.xample, if the OFFSET level is +4 dB, the amplifier’s output is 4 dB over the average recorded 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
DSP m odes
The DSP (Digital Signal Processing) modes allow you to transform your living room into a variety of different
sonic environments when playing either two-channel or multi-channel sources.
HALL 1
Simulates the acoustic effects of a large concert hall. Suitable for classical music.
A long delay time of reflected sounds, coupled with reverb effects, let the listener enjoy the dynamic and
rich sounds characteristic of concert halls and powerful orchestral performances.
HALL 2
Simulates the acoustic environment of a very resonant concert hall. Rich reverberation and a full sound
create the impression of a lively performance space.
J AZZ
Simulates the acoustic effects of a jazz club. Reflected sound is virtually below 100 msec so that the listener
can enjoy a live band effect.
DANCE
Simulates the acoustic effects of a dance club. Features a strong bass sound.
Reflected sound delay time is virtually below 50 msec, for the listener to enjoy the the visceral power of
dance music.
THEATER 1
Reproduces theater sound field effects without losing the localization of each channel. Theater effects can
be enjoyed without losing Dolby Digital/ Pro Logic effects when used in combination those formats (with
movies bearing the 3 trademark).
THEATER 2
Simulates the acoustic environment of a theater while maintaining proper localization of each channel.
Stereo m ode
Use the STEREO mode to enjoy standard (two-channel) stereo sound from the front left and right speakers.
This m ode also allow s you to :
• Use the BASS and TREBLE tone controls
• Use DIRECT for truer reproduction of the original recording.
• Use DIGITAL NR.
See display explanations on p.18-19 and front panel explanations on p.20-23 for details on SPEAKERS (A/B),
BASS (–/+) and TREBLE (–/+). See P.45 for DIGITAL NR explanation.
When listening to Dolby Digital or DTS sources, DIGITAL NR do not function even if you select
STEREO.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Selecting a Sound Mode
To ensure the best possible surround sound, be sure to complete the set up procedures described in “Setting
Up for Surround Sound” (starting on page 27) before using the sound modes. This is particularly important when
using the 2 (Dolby) Digital or DTS sources. When using the sound modes, using SPEAKERS A will give the
best results. If you use SPEAKERS B, the sound will be down mixed to the two front B speakers and the
surround sound effect will be lost.
Surrround operation
Î
RECEIVER
1 Select the sound m ode.
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
• For HOME THX CINEMA \ Press THX
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
• For ADVANCED THEATER \ Press ADVANCED THEATER
Each press changes the ADVANCED THEATER mode as follows:
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
MUSICAL
DRAMA
ACTION
CHANNEL
-
+
2
5
8
0
3
1
5-D THEATER
6
9
4
• For STANDARD or MPEG (VSX-D938TX only) \ Press
STANDARD (MPEG (VSX-D938TX only))
Each press changes the STANDARD and MPEG (VSX-D938TX
only) modes as follows:
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
STANDARD
MPEG
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
• For DSP modes \ Press DSP repeatedly
Each press changes the DSP mode as follows:
SIGNAL
SELECT
2/ dts
THX
ADVANCED
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
STANDARD
STEREO
HALL 1
THEATER 2
• For STEREO \ Press STEREO
HALL 2
JAZZ
DANCE
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
THEATER 1
DSP
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
DSP
STEREO
• The effects of ADVANCED THEATER mode can be adjusted
in the range of 10 to 90 by pressing EFFECT –/+. (The default
setting is 70). Also, the effect level can be set in each
ADVANCED THEATER mode by pressing the EFFECT(–/+)
button. 5-D THEATER modes cannot be changed.
• The amount of effect of each DSP mode can be adjusted in
the range of 10 to 90 (the default setting value is 70) by
pressing EFFECT –/+.
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
STANDBY/ ON
DSP
MODE
STANDBY
STEREO
DTS
THX CINEMA ADVANCED
STANDARD
MPEG
5
-CHANNEL EQUAL POWER OUTPUT
VIDEO INPUT
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
SIGNAL
SELECT
NR
S-VIDEO
VIDEO
L
AUDIO
R
PHONES
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
• When a digital input is selected, using some discs with a huge
amount of information may cause the overload indicator to
light up. If the overload indicator is lit in the THX, ADVANCED
THEATER and DSP modes, the signal may be distorting. To
ensure there is no distortion you can switch to the
STANDARD mode.
VSX-D938TX
STANDARD
THX
CINEMA
ADVANCED
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Playing Sources w ith Dolby Digital or DTS Sound
The following instructions show you how to play Dolby Digital, DTS sound MPEG Audio (VSX-D938TX only)
sources with the VSX-D938TX/D908TX/D908TX-G.
Î
RECEIVER
1 Turn on the receiver.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
1
2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 Use the MULTI CONTROL buttons or the FUNCTION
button on the rem ote control, or the INPUT
SELECTOR dial on the front panel to select the
com ponent (DVD/ LD etc.) you w ant to listen to/
w atch.
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
You can only use this remote to control the component if it’s made
by POINEER. For all other makers you need to setup the remote
specifically to control your component (See p. 54).
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
3 Choose a 2 surround/ dts m ode by pressing
ADVANCED THEATER or STANDARD.
TV VOL
VOLUME
6
TV FUNC
(For more details, see “Sound Modes” p. 39-40.)
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
2
4
3
4 Press SIGNAL SELECT on the rem ote control or
SIGNAL SELECT on the front panel to select the input
signal corresponding to the source com ponent (VSX-
D938TX can be set to AUTO, w hile the VSX-D908TX/
D908TX-G should be set to DIGITAL).
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
(See “Switching ANALOG/DIGITAL signal input” on p. 44.)
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
5 Play a source (for exam ple, a DVD player).
VSX-D938TX
6 Adjust the volum e by using the MASTER VOLUME
buttons on the rem ote control or the MASTER
VOLUME on the front panel.
1
3
2
6
We recommend using different modes for different types of
DTS material. For watching movies, the THX or ADVANCED
THEATER setting should provide the best results. For listening
to music, the STANDARD, DIRECT, STEREO, or DSP modes
should serve the listener best.
VSX-D938TX
VSX-908TX and VSX-D908TX-G m odels:
When playing LD recorded in Dolby Digital
4
When connecting a DVD/LD or LD player using the AC-3 RF
output, a commercially available RF demodulator (RFD-1) is
required. The RF demodulator changes the RF signal to a digital
signal which is then processed by the receiver at the digital
input jacks. For more details, refer to the instruction manual
supplied with the RFD-1 (see p.11).
Refer to pages 76-78 for explanations of Dolby Digital, Dolby
Pro Logic, DTS, and MPEG (VSX-D938TX only).
VSX-D938TX m odel:
Make sure you connect your DVD/LD or LD players using the
AC-3 RF jack. If your player has an AC-3 RF output, this will
ensure you can use all LD players. Refer to page 10, 11 and 37.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Using MPEG audio discs (VSX-D938TX only)
The VSX-D938TX can decode a variety of different types of audio formats for DVDs and these include MPEG.
MPEG is a highly sophisticated audio encoding system which some discs use. If the disc you are using has
MPEG audio (it will be marked on the disc) switch the receiver to MPEG using the procedure below. If you try to
play an MPEG audio disc in any mode other than MPEG no sound will be heard.
1
2
If the receiver is not in STANDARD m ode, put it in that
m ode by pressing the STANDARD (MPEG) button.
1
VSX-D938TX
Press the STANDARD (MPEG) button to sw itch into
MPEG m ode. Each press sw itches betw een regular
STANDARD m ode and MPEG m ode.
“MPEG” will light up in the main display to cofirm you are in MPEG
mode. After that a small “MPEG” will appear in the bottom left of
the display window where “AC-3” or “DTS” would appear if you
were in one of those modes. If this “MPEG” display is flashing it
means the MPEG signal is not being receiverd.
Main display
SIGNAL
SELECT
SIGNAL
SELECT
SP
A
DIGITAL
DIGITAL
MPEG
MPEG
MPEG
• If the disc you are using is not an MPEG disc or there is some
other problem, the small “MPEG” display will flash. This will
also happen when the disc is paused.
• You can’t use any other sound mode (ADVANCED,
STANDARD, etc., when using the MPEG mode.
• If you use a disc that is not MPEG when the receiver is in
MPEG mode, no sound will be heard.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Sw itching ANALOG/ DIGITAL signal input
This switch moves the input fed to the receiver between analog, digital and AC-3 RF sources. You need to take
special care to switch to the appropriate input, when necessary. For example, the switch would have to be on
digital to use DOLBY DIGITAL, DTS surround sound and MPEG audio (VSX-D938TX only) but it would have to be
on analog to record from the analog out jacks on the receiver. On the VSX-D938TX, the default setting is AUTO
(which chooses digital when all three are available but foes with whatever is available if it is the only choice), on
the VSX-D908TX/D908TX-G is ANALOG.
Î
RECEIVER
1 Press SIGNAL SELECT on the rem ote control or on the
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
front panel to select the input signal corresponding to
the source com ponent.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
Each press switches the signal in the order below:
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
VSX-D938TX model
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
AUTO
ANALOG
DIGITAL
2
5
8
0
3
1
AC-3 RF
VSX-D908TX/D908TX-G models
6
9
4
7
ANALOG
+1 0
DISC
DISPLAY
RF ATT
DIGITAL
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
2 While SIGNAL SELECT is set to DIGITAL, AC-3 lights
w hen a Dolby Digital signal is input, and DTS lights
w hen a DTS signal is input
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
SIGNAL
SELECT
SIGNAL
SELECT
A
When a Dolby Digital
SP
SIGNAL
SELECT
DIGITAL
DIGITAL
AC-3
2/ dts
SYSTEM
SETUP
signal is input.
AC-3
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
SIGNAL
SELECT
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
SIGNAL
SELECT
SP
A
When a DTS signal is
input.
DIGITAL
DIGITAL
DTS
VSX-D938TX
DTS
VSX-D938TX
VSX-D938TX only
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
SIGNAL
SELECT
SIGNAL
SELECT
STANDBY/ ON
DSP
MODE
STANDBY
STEREO
SP
A
DIGITAL
When MPEG signal
is input.
/
DTS
DIGITAL
THX CINEMA ADVANCED
STANDARD
MPEG
MPEG
MPEG
5
-CHANNEL EQUAL POWER OUTPUT
VIDEO INPUT
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
NR
SIGNAL
SELECT
S-VIDEO
VIDEO
L
AUDIO
R
PHONES
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
• In the AUTO setting (VSX-D938TX only), SIGNAL SELECT
chooses the signal in the following order: AC-3 RF, DIGITAL,
ANALOG.
• If the Digital-In Select (see p.37) choices are set to OFF, the
SIGNAL SELECT will default to ANALOG.
• Because the audio from a karaoke microphone and LD
recorded with analog audio only is not output from the digital
output, set SIGNAL SELECT to “ANALOG”.
SIGNAL SELECT
• This receiver can only play back Dolby Digital, PCM (32kHz,
44kHz, 48kHz, and 96kHz), DTS, or MPEG digital signal
formats. It cannot play back digital singals other than these so
for those formats you will have to play them back in an analog
manner (making sure your equipment is hooked up with
analog connections and setting the SIGNAL SELECT to
“ANALOG.”
• When an LD or CD with DTS is played back with the SIGNAL
SELECT set in “ANALOG,” digital noise caused by playing
back the DTS directly (with no decoding) is output. To prevent
noise, you need to make digital connections (See p. 10, 11)
and set SIGNAL SELECT to “DIGITAL”(VSX-D938TX could
also be set to “AUTO”).
• Some DVD players do not output DTS signals. For more
details, refer to the instruction manual supplied with your
DVD player.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Reducing noise during playback (DIGITAL NR function)
To reduce extraneous noise switch on DIGITAL NR. This noise reduction can only be used in the STEREO mode.
Î
S0 URCE
RECEIVER
1 Press STEREO on the rem ote control or on the front
panel.
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
4
-
8
+
2 Press DIGITAL NR on the rem ote control or on the
front panel.
TUNING
STATION
+
¡
1
¢
CHANNEL
+
2
5
8
0
3
1
Each press switches DIGITAL NR on or off.
6
9
4
SIGNAL
SELECT
STEREO
SIGNAL
SELECT
STEREO
VOLUME
VOLUME
SP
A
SP
A
DIGITAL
DIGITAL
dB
7
dB
j
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
• When DIGITAL NR is on and Dolby Digital, DTS or MPEG
(VSX-D938TX only) signals are input, DIGITAL NR is
automatically switched off.
• In cases described below, noises may not be reduced even if
DIGITAL NR is on.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
· Sudden noise
· Extremely loud noise
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
· Signals that do not contain many high frequencies
• For each source, DIGITAL NR is effective at and above levels
shown below.
MIDNIGHT
DSP
STEREO
1,2
DIGITAL NR
· Cassette tape .................. 20 dB
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
· Video tape ........................ 15 dB
· AM tuner ............... 10 to 15 dB
· FM tuner .................15 to 16 dB
* Depending on the condition of the source, there may not be a
noticeable improvement in the quality of the sound.
VSX-D938TX
1 2
VSX-D938TX
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Listening in MIDNIGHT LISTENING m ode
This feature makes it possible to get excellent surround sound effects even when listening at low volumes. It
can be used with a variety of surround sound sources and plays soundtracks so that the quieter sounds are
audible while the noisier sounds do not become overly loud or distorted. It does this by bringing all the sounds in
a given soundtrack closer together in volume. Compare this feature with the D-Range Control (only for Dolby
Digital sources) on p. 36.
Î
S0 URCE
RECEIVER
Press MIDNIGHT.
MULTI
OPERATION
SYSTEM
OFF
Each press switches MIDNIGHT LISTENING mode on or off.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
SIGNAL
SELECT
ANALOG SP
MIDNIGHT
STEREO
VOLUME
TUNING
STATION
+
¡
A
1
4
¢
dB
CHANNEL
-
+
AUTO
2
5
8
0
3
1
6
9
4
7
+1 0
DISC
DISPLAY
RF ATT
• The effect adjusts itself automatically in accordance with the
volume level.
TV
TV CONTROL
TV VOL
VOLUME
• You cannot use the MIDNIGHT LISTENING mode with the
DIRECT or EXTERNAL DECODER modes.
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
MIDNIGHT
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
MIDNIGHT
VSX-D938TX
DEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
TAPE
2
DSP
MODE
STEREO
MONITOR
/
DTS
FL
DIMMER
ADVANCED
STANDARD
MPEG
TUNER CONTROL
L
POWER OUTPUT
VIDEO INPUT
IDEO
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
SIGNAL
SELECT
NR
CLASS
MPX
FM/ AM
–
TUNING
+
L
AUDIO
R
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
MEMORY
–
STATION
+
DOWN
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
External decoder playback (front panel only)
This feature allows you to connect an external decoder to enjoy certain types of specialized discs.
EXTERNAL DECORDER IN
Press EXTERNAL DECORDER IN.
VSX-D938TX
Each press switches the input between the previous mode and
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
EXTERNAL DECODER.
STANDBY/ ON
DSP
MODE
STANDBY
STEREO
/
DTS
THX CINEMA ADVANCED
STANDARD
MPEG
SIGNAL
SELECT
ANALOG SP
VOLUME
A
dB
TUN
FM/
5
-CHANNEL EQUAL POWER OUTPUT
VIDEO INPUT
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
SIGNAL
SELECT
NR
CLASS
MPX
S-VIDEO
VIDEO
L
AUDIO
R
PHONES
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
MEM
When EXTERNAL DECORDER is selected only the volume level
and channel levels can be set. All of this unit’s other features
(DSP modes. ADVANCED THEATER modes, DIRECT mode,
TONE controls, etc.), as well as the TUNER and PHONO
modes, cannot be used. Also, all speaker settings and other
setup settings have no effect.
96kHz/ 24bit perform ance
This receicver is capable of playing back advanced DVD discs which are recorded in 96 kHz/24 bit format (these
are all stereo discs). The receiver will automatically read the format of the disc and play accordingly (of course
the SIGNAL SELECT will have to set to AUTO (VSX-D938TX only) or DIGITAL to read the DVD soundtrack).
When the receiver plays a 96 kHz/24 bit disc “96kHz” appears in the display. If you try to use one of the
functions or modes mentioned below “96kHz” will light on the display, as shown below, indicating the
procedure is not possible.
SIGNAL
SELECT
STEREO
VOLUME
SP
A
DIGITAL
dB
• When a 96 kHz/24 bit disc is played back, the volume
may be louder than that of a normal disc.
• Some DVD players cannot play 96 kHz/24 bit discs.
Check the manual of your DVD player to make sure.
• During this playback, you cannot use the tone controls,
the DIRECT function, the LOUDNESS function, any of
the sound modes, or any of the effect modes.
• With 96 kHz/24 bit discs, you are able to use 5.1 ch
playback and the TAPE 2 MONITOR.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Listening in LOUDNESS m ode (front panel only)
The LOUDNESS mode allows you to boost the bass in a signal. It is useful for listening to music at low volumes.
LOUDNESS
Press LOUDNESS.
VSX-D938TX
Each press switches LOUDNESS mode on or off.
DEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
TAPE
2
DSP
MODE
STEREO
MONITOR
/
DTS
FL
DIMMER
SIGNAL
SELECT
ANALOG SP
LOUDNESS
STEREO
ADVANCED
STANDARD
MPEG
VOLUME
A
dB
TUNER CONTROL
L
POWER OUTPUT
VIDEO INPUT
IDEO
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
SIGNAL
SELECT
NR
CLASS
MPX
FM/ AM
–
TUNING
+
L
AUDIO
R
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
MEMORY
–
STATION
+
DOWN
You cannot use the LOUDNESS mode with the DIRECT or
EXTERNAL DECODER modes.
Adjusting bass and treble (tone control) (front panel only)
Use BASS (–/+) or TREBLE (–/+) to adjust the low and high frequencies (the receiver must be in STEREO mode).
BASS –/+
Press BASS (–/ +) to adjust the low frequencies.
VSX-D938TX
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
DEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
A
dB
TAPE
2
DSP
MODE
STEREO
MONITOR
/
DTS
FL
DIMMER
ADVANCED
STANDARD
MPEG
TUNER CONTROL
L
POWER OUTPUT
VIDEO INPUT
IDEO
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
SIGNAL
SELECT
NR
CLASS
MPX
FM/ AM
–
TUNING
+
L
AUDIO
R
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
MEMORY
–
STATION
+
Press TREBLE (–/ +) to adjust the high frequencies.
DOWN
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
A
dB
TREBLE –/+
• The tone control can be adjusted in a range of ±6 dB.
• The tone control cannot be adjusted in STANDARD,
ADVANCED THEATER modes as well as DSP, EXTERNAL
DECODER, DIRECT, and 96kHz settings.
Direct playback (front panel only)
DIRECT
Press DIRECT to put the receiver in DIRECT m ode.
This mode will give you the most accurate reproduction of two channels
sources.
VSX-D938TX
DEO MULTI-CHANNEL RECEIVER
Digital Signal Processor
TAPE
2
DSP
MODE
STEREO
MONITOR
/
DTS
FL
DIMMER
ADVANCED
STANDARD
MPEG
None of the tone controls, channel level or other sound modes
can be used.
TUNER CONTROL
L
POWER OUTPUT
VIDEO INPUT
IDEO
EXTERNAL
DECODER IN DIRECT LOUDNESS MIDNIGHT
DIGITAL
SIGNAL
SELECT
NR
CLASS
MPX
FM/ AM
–
TUNING
+
L
AUDIO
R
SPEAKERS
–
BASS
+
–
TREBLE
+
INPUT ATT
MEMORY
–
STATION
+
DOWN
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
Adjusting the brightness of the display (front panel only)
Use the FL DIMMER button to adjust the brightness of the fluorescent display (FL=fluorescent display).
FL DIMMER
Press FL DIMMER.
VSX-D938TX
Four levels of brightness ranging from very dim to very bright can be
Digital Signal Processor
selected. Each press changes the brightness of the display. When
INPUT
SELECTOR
TAPE
2
MONITOR
rotating through the options, the default brightness can also be selected.
FL
DIMMER
MASTER
VOLUME
TUNER CONTROL
DIGITAL
NR
SIGNAL
SELECT
RECT LOUDNESS MIDNIGHT
CLASS
MPX
FM/ AM
–
TUNING
+
Please note: it is a feature of this unit that the fluorescent
display will be brighter for a few seconds after you choose a
function (like DVD/LD, CD, etc.) and then get softer. This will
still happen when you adjust the brightness but the new setting
will be the one the display softens to.
–
BASS
+
–
TREBLE
+
INPUT ATT
MEMORY
–
STATION
+
DOWN
UP
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
Autom atic and Manual Tuning
The following steps show you how to tune in FM and AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. If you already know the exact frequency of the station you desire, see “Direct
Access Tuning” on the following page.
Î
RECEIVER
1 Press TUNER on the rem ote control or turn the INPUT
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
SELECTOR on the front panel.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
On the remote, this selects the TUNER function on the receiver
and sets the remote to the TUNER operation mode.
MULTI CONTROL
MD/
1
2
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
MPX
¶
-
3
-
8
+
TUNING
STATION
+
¡
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
1
4
¢
A
CHANNEL
-
+
dB
3
FM
2
5
8
0
3
1
6
9
4
7
+1 0
DISC
DISPLAY
2 Press BAND on the rem ote control or FM/ AM on the
front panel to select the band (FM or AM).
Each press switches the band: FM j AM
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
4
TV FUNC
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
A
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
dB
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
3 Tune in the station.
MIDNIGHT
DSP
STEREO
DIGITAL NR
For Autom atic Tuning
Press and hold TUNING –/+ for about one second, then release.
The tuner starts searching the selected band and stop automatically
at the first station it locates. Repeat to locate other stations.
For Manual Tuning
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
• To change frequencies one step at a time, press TUNING –/+
repeatedly.
VSX-D938TX
• To change frequencies quickly, hold down TUNING –/+ and
release when you reach the frequency you desire.
2 3 1
VSX-D938TX
4 Adjust the volum e.
MPX m ode
If the TUNED or STEREO indicators do not light when tuning an FM
station, because the station is too far away or the broadcast signal is
weak, press MPX on the remote control or front panel to switch to
MONO reception. This should improve reception enough for you to
enjoy the broadcast.
MPX
4
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
Direct Access Tuning
The following steps show you how to tune directly to a specific frequency using the remote control.
Î
RECEIVER
1 Press TUNER.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
This selects the TUNER function on the receiver and sets the
remote control to the TUNER operation mode.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
1
2
3
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
2 Press BAND on the rem ote control or FM/ AM on the
front panel to select the band (FM or AM).
Each press switches the band : FM j AM
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
4
7
3 Press DIRECT ACCESS to activate the Direct Access
Tuning m ode.
+1 0
DISC
DISPLAY
RF ATT
The cursor blinks in the display on the front panel.
TV
TV CONTROL
TV VOL
VOLUME
SIGNAL
SELECT
ANALOG SP
STEREO
5
VOLUME
TV FUNC
A
dB
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
4 Use the num ber buttons to enter the frequency of the
station you desire.
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
Exam ple:
To tune station 106.00 (FM), press:
1
0
6
0
0
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
VSX-D938TX
A
dB
STEREO
TUNED
To cancel before inputting the frequency
Press DIRECT ACCESS, and enter the frequency again.
5 Adjust the volum e.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
Mem orizing Frequently Used Stations
The following steps show you how to memorize up to 30 radio stations in 3 classes (each holding 10 channels).
When memorizing FM frequencies, the receiver also memorizes the MPX mode (STEREO or MONO).
Using the front panel
1 Tune in the desired station.
3
See “Automatic and Manual Tuning” or “Direct Access Tuning” on
pages 50 and 51.
VSX-D938TX
2 Press MEMORY to activate the m em ory function.
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
A
dB
STEREO
TUNED
2 4
3 Press CLASS repeatedly to select a class num ber.
Each press switches the display:
CLASS A
CLASS B
CLASS C
4 Press STATION –/ + repeatedly to select a channel
(0~9) w ithin the respective class.
The station is memorized automatically after 5 seconds.
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
A
dB
STEREO
TUNED
Repeat steps 1 through 4 to m em orize up to 30 stations.
If you w ant to escape from MEMORY m ode
Press MEMORY again.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
Recalling Mem orized Stations
Using the rem ote control
Î
RECEIVER
1 Press TUNER.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
This selects the TUNER function on the receiver and sets the
remote control to the TUNER operation mode.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
1
3
TUNER
TV CONT
TAPE1
MPX
7
SIGNAL
SELECT
ANALOG SP
STEREO
CLASS
BAND DIRECT ACCESS
VOLUME
¶
-
3
-
8
+
A
dB
2
TUNING
STATION
+
¡
FM
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
7
2 Press CLASS repeatedly to select a class num ber.
+1 0
DISC
DISPLAY
RF ATT
Each press switches the display:
TV
TV CONTROL
CLASS A
CLASS B
CLASS C
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
3 Use the num ber buttons to select the channel you
w ant.
SIGNAL
SELECT
2/ dts
7
To select channel 7, press
To select channel 0, press
.
.
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
0
DIGITAL NR
For exam ple : If 99.50 MHz (FM) was memorized in class A at
channel 7.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
SIGNAL
SELECT
ANALOG SP
STEREO
VOLUME
A
dB
STEREO
TUNED
VSX-D938TX
To skip through each channel in order
Press STATION –/+ repeatedly.
Using the front panel
2
1
1 Select the TUNER function by using INPUT
SELECTOR.
VSX-D938TX
2 Press CLASS repeatedly to select a class num ber.
3 Press STATION –/ + repeatedly to select the channel
you w ant.
3
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
Setting Up the Rem ote Control to Control Other
Com ponents
In addition to controlling the receiver, the supplied remote control can operate your other components (VCR, TV,
LD, CD, etc.) after you program it to do so. In this way, instead of fumbling with many different controls and
buttons, you only need to use one remote control. If your component(s) are listed in the remote control’s
memory, simply follow the steps below. If your component(s) are not listed, or if you want the remote control to
learn additional operations, you can use the learning mode to input the information from the remote controls
supplied with your other components.
Recalling preset codes
The following steps show you how to recall preset codes stored in the remote control. Once a preset code is
recalled and the component assigned, you can use this remote control to easily operate the component.
See “Preset Code List” on p.79-82 (VSX-D938TX), 83 (VSX-D908TX/D908TX-G) for the components and
manufacturers available.
Î
RECEIVER
1 Turn on your TV and the receiver.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
Make sure your TV is set to the appropriate video input (e.g. VIDEO
1).
1
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
2 Press REMOTE SETUP.
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
The REMOTE SETUP menu appears on your TV screen.
2
5
8
0
3
1
3
Select Remote
Setup Mode
6
9
4
7
Remote SETUP+1
Preset Recall
+1 0
DISC
DISPLAY
RF ATT
Remote SETUP+2
Learning
TV
TV CONTROL
TV VOL
VOLUME
Remote SETUP+3
Multi-Operation
Remote SETUP+4
Direct Function
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
You have four set up options:
SIGNAL
SELECT
1 PRESET RECALL
2 LEARNING
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
3 MULTI OPERATION (See p.69)
4 DIRECT FUNCTION (See p.72)
PRESET RECALL and LEARNING are the two modes that teach the
remote control to operate your other components. It is easiest to
start with PRESET RECALL and, if set up is not possible, move on
to the LEARNING mode.
DIGITAL NR
2,3
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
1
3 Press REMOTE SETUP and
at the sam e tim e to
select the PRESET RECALL SETUP m ode.
All the MULTI CONTROL buttons (except the TUNER button) start
to blink.
To cancel the PRESET RECALL SETUP m ode
Press REMOTE SETUP.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
Î
RECEIVER
4 Press MULTI CONTROL for the com ponent you w ant
to control.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
The selected button lights steadily and the first manufacturer (and
preset code(s)) appear on your TV screen.
MULTI CONTROL
MD/
4
5
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
Preset Recall
1
4
¢
CHANNEL
-
+
1Select function
2
5
8
0
3
1
2Select products [5∞23]
3Input ID CODE
6
9
4
6
7
7
2 [TAPE ] 3
Page 1/11
5 [SONY
] ∞
+1 0
DISC
DISPLAY
[
[
801 806
]
]
RF ATT
TV
TV CONTROL
EXIT=Remote setup
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
5 Press 5¥∞ repeatedly to display the nam e of the
com ponent’s m anufacturer.
SIGNAL
SELECT
Most manufacturers have been programmed into the receiver, but
if your component is made by a small or relatively unknown
manufacturer you may not be able to find it.
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
6 Point the rem ote tow ard the com ponent to be
controlled, enter the 3 digit setup code.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
When you enter the setup code, the remote emits a power ON/
OFF signal. If the component turns ON or OFF, you have entered
the proper code.
VSX-D938TX
If the component does not turn ON or OFF and there is more than
one setup code, try inputting another code (starting again from step
4). Some manufacturers use several sets of remote control signals
and the first code may not correspond to your component.
Repeat steps 4 through 6 to assign preset codes for as m any
com ponents as necessary.
If you cannot get your com ponent to respond to any of the
codes you can still program the com ponent into the rem ote
control using the procedure in the next section.
7 Press REMOTE SETUP to exit the PRESET RECALL
SETUP m ode.
The remote control and TV return to their previous operation
modes.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
Learning m ode: Program m ing signals from other rem ote controls
If preset codes are not available for your component(s), or the available preset codes do not operate correctly,
you can use this function to program in signals from the remote control(s) of your other component(s). This
operation can also be used after recalling a preset code to program additional operations not covered in the
preset codes.
Î
RECEIVER
1 Turn on your TV and the receiver.
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
Make sure your TV is set to the appropriate video input (e.g. VIDEO
1).
1
4
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
2 Press REMOTE SETUP.
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
The REMOTE SETUP menu appears on your TV screen.
2
5
8
0
3
1
Select Remote
Setup Mode
3
6
9
4
7
Remote SETUP+1
Preset Recall
+1 0
DISC
DISPLAY
RF ATT
Remote SETUP+2
Learning
TV
TV CONTROL
TV VOL
VOLUME
Remote SETUP+3
Multi-Operation
Remote SETUP+4
Direct Function
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2
3 Press REMOTE SETUP and
at the sam e tim e to
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
select the LEARNING SETUP m ode.
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
2,3
All the MULTI CONTROL buttons (except the TUNER button) start
to blink.
DIGITAL NR
To cancel LEARNING SETUP m ode
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
Press REMOTE SETUP.
Learning Setup
VSX-D938TX
1Place both commanders
pointing at each other.
2Select the item from
the Multi-control
buttons that should be
duplicated. (ex. DVD)
Multi-control button
starts blinking.
EXIT=Remote setup
4 Press MULTI CONTROL for the com ponent you w ant
to control.
Each button can be set to control one of the follow ing
com ponents.
The selected button continues to blink.
Learning Setup
3Press one button that
should be duplicated.
4Multi-Contorol button
lights up.
5Press one button on the
original commander, and
hold 2 to 10 seconds.
6Repeat this process to
duplicate next command.
EXIT=Remote setup
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
Î
RECEIVER
5 Press the button to be program m ed.
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
The MULTI CONTROL button lights steadily.
• The TV POWER, TV FUNC and TV VOL +/– buttons are only
available for learning when programming TV CONTROL
operations.
5
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6 Point the rem ote controls at each other and press the
button on the other rem ote control for the operation
you w ish to program .
6
9
4
7
1 Point the remote controls toward each other.
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
7 cm
TV VOL
VOLUME
TV FUNC
2 Hold down the button on the other remote control
corresponding to the operation you wish to program. Release
when the MULTI CONTROL button on the receiver’s remote
control starts blinking.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
(The MULTI CONTROL button blinks to indicate that the
operation has been learned.)
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
7
To program additional operations for the current com ponent
Repeat steps 5 and 6.
To program operations for another com ponent
Repeat steps 4 through 6.
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
7 Press REMOTE SETUP to exit the LEARNING SETUP
m ode.
VSX-D938TX
The remote control and TV return to their previous operation
modes.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
Rem ote Controlling Other Com ponents
DVD or LD player operations
• The following operations are available from the receiver’s remote control after you program your DVD
or LD player’s preset code, but some operations may need to be learned by the receiver (see “Setting
Up the Remote Control Other Components,” p.54-57).
• To perform these operations, press the DVD/LD button to set the remote to the DVD or LD operation
mode.
• For more information on individual commands, consult the manual that came with the component.
1
SOURCE
Î
S0 URCE
RECEIVER
Press to switch the DVD or LD player on or off.
MULTI
OPERATION
SYSTEM
OFF
1
2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 7
8
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
Press to stop playback.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
3
4
9
0
TUNING
STATION
+
¡
2 ¶ (TOP MENU)
1
4
¢
CHANNEL
-
+
Use to display or close the top menu screen (for
DVD only).
2
5
8
0
3
1
6
9
4
5
6
7
4 1¥¡
+1 0
DISC
DISPLAY
-
=
1 : Hold down for fast reverse playback.
RF ATT
¡ : Hold down for fast forward playback.
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
5 Num ber buttons
Use to select chapters (tracks).
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
6 +10
Use when selecting chapter (track) numbers
higher than 10.
SIGNAL
SELECT
2/ dts
7
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
7 5¥∞¥2¥3¥ENTER
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
5¥∞¥2¥3 : Use to navigate through options on
menu screens and to change settings.
ENTER : Use to implement settings selected
with the cursor buttons or to set items
highlighted in a menu (for DVD only).
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
8 3
Press to start playback.
9 8
Press to pause playback.
0 4¥¢
4 : Press to return to the beginning of the
current chapter (track). Press repeatedly to return
to the beginning of previous chapters (tracks).
¢ : Press to advance to the beginning of the
next chapter (track). Press repeatedly to advance
to the beginning of following chapters (tracks).
- ENTER (SIDE A/ B)
Use to change the LD between sides A and B (for
LD only).
= MENU
Press to call up the menu screen on the DVD.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
VCR and DVD video recorder operations
• The following operations are available from the receiver’s remote control after you program your VCR
or DVD video recorder’s preset code, but some operations may need to be learned by the receiver
(see “Setting Up the Remote Control to Control Components,” p.54-57).
• To perform these operations, press the VCR 1 or VCR 2 button to set the remote to the VCR, DVD
video recorder 2 operation mode.
• For more information on individual commands, consult the manual that came with the component.
1
SOURCE
Î
RECEIVER
S0 URCE
Press to switch the VCR or DVD video recorder
on or off.
MULTI
SYSTEM
OFF
OPERATION
1
2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
8
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
2 7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
3
4
9
0
Press to stop playback.
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
3 ¶
2
5
8
0
3
1
Press to start recording.
6
9
4
5
6
7
4 1¥¡
+1 0
DISC
DISPLAY
-
=
1 : Hold down for fast reverse playback.
RF ATT
¡ : Hold down for fast forward playback.
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
5 Num ber buttons
Use to select channels.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
6 +10
Use when selecting chapter (track) numbers
higher than 10 (for DVD video recorder only).
SIGNAL
SELECT
2/ dts
7
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
7 5¥∞¥2¥3¥ENTER
MIDNIGHT
DSP
STEREO
DIGITAL NR
5¥∞¥2¥3: Use to navigate through options on
menu screens and to change settings.
ENTER: Use to implement settings selected with
the cursor buttons or to set items highlighted in a
menu (for DVD video recorder only).
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
8 3
Press to start playback.
9 8
Press to pause playback.
0 CHANNEL –/ +
Use to change channels on the VCR’s tuner.
- ENTER(TV/ VCR)
Use this button to switch the VCR between its
tuner (for watching videos) and the TV.
Press to stop recording (for DVD video recorder
only).
= MENU
Press to call up the menu screen on the DVD (for
DVD video recorder only).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
CD player operations
• The following operations are available from the receiver’s remote control after you program your CD
player’s preset code, cut some operations may need to be learned by the receiver (see “Setting Up
the Remote Control to Control Other Components,” p.54-57).
• To perform these operations, press the CD button to set the remote control to the CD operation
mode.
• For more information on individual commands, consult the manual that came with the component.
1
SOURCE
Press to switch the CD player on or off.
Î
RECEIVER
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
1
2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 7
7
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
Press to stop playback.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
3
4
8
9
TUNING
STATION
+
¡
1
4
¢
3 ¶
CHANNEL
-
+
2
5
8
0
3
1
Press to start recording (for CD-R only).
6
9
4
5
6
4 1¥¡
7
1 : Hold down for fast reverse playback.
+1 0
DISC
DISPLAY
0
¡ : Hold down for fast forward playback.
RF ATT
TV
TV CONTROL
5 Num ber buttons
TV VOL
VOLUME
TV FUNC
Use to select tracks.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
6 +10
You can also use this button when selecting track
numbers higher than 10.
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
7 3
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
Press to start playback.
DIGITAL NR
8 8
Press to pause playback.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
9 4¥¢
4 : Press to return to the beginning of the
current track. Press repeatedly to return to the
beginning of previous tracks.
VSX-D938TX
¢ : Press to advance to the beginning of the
next track. Press repeatedly to advance to the
beginning of following tracks.
0 DISC
Use to switch between discs with multi disc play.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
MD operations
• The following operations are available from the receiver’s remote control after you program your MD
recorder’s preset code, but some operations may need to be learned by the receiver (see “Setting up
the Remote Control to Control Other Components,” p.54-57).
• To perform these operations, press the MD/TAPE 1 button to set the remote control to the MD
operation mode.
• For more information on individual commands, consult the manual that came with the component.
1
SOURCE
Press to switch the MD player on or off.
Î
RECEIVER
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
1
2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 7
7
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
Press to stop playback or recording.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
3
4
8
9
TUNING
STATION
+
¡
1
4
¢
3 ¶
CHANNEL
-
+
2
5
8
0
3
1
Press to start recording (may put some decks in
REC PAUSE mode).
6
9
4
5
6
7
4 1¥¡
+1 0
DISC
DISPLAY
0
1 : Hold down for fast reverse playback.
RF ATT
¡ : Hold down for fast forward playback.
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
5 Num ber buttons
Use to select tracks.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
6 +10
You can also use this button when selecting track
numbers higher than 10.
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
7 3
MIDNIGHT
DSP
STEREO
DIGITAL NR
Press to start playback.
8 8
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
Press to pause playback.
9 4¥¢
VSX-D938TX
4 : Press to return to the beginning of the
current track. Press repeatedly to return to the
beginning of previous tracks.
¢ : Press to advance to the beginning of the
next track. Press repeatedly to advance to the
beginning of following tracks.
0 DISC (DISP/ CHARA)
Allows you to change the display mode of the
MD.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
STB (Satellite Tuner) operations
• The following operations are available from the receiver’s remote control after you program your
satellite tuner’s (or Cable TV’s) preset code, but some operations may need to be learned by the
receiver (see “Setting Up the Remote Control to Control Other Components,” p.54-57).
• To perform these operations, press the TV/SAT button to set the remote control to the SAT operation
mode.
• For more information on individual commands, consult the manual that came with the component.
1
SOURCE
Press to switch the satellite tuner on or off.
Î
RECEIVER
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
1
2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 ¶¥7¥3¥8¥1 (A/ B/ C/ D/ E)
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
Use to make selections from satellite functions.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
1
4
¢
3 Num ber buttons
CHANNEL
-
+
2
5
8
0
3
1
Use to select satellite channels.
6
9
4
3
4
4 GUIDE
7
Use to turn the program information screen on or
off.
+1 0
DISC
DISPLAY
6
7
RF ATT
TV
TV CONTROL
5 5¥∞¥2¥3¥ENTER
TV VOL
VOLUME
TV FUNC
5¥∞¥2¥3 : Press the button to select items on
the SAT GUIDE screen or SAT MENU screen.
ENTER: Press to activate the selected function.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
6 EXIT
SIGNAL
SELECT
Press to exit the current setting of the SAT.
2/ dts
5
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
7 MENU
MIDNIGHT
DSP
STEREO
DIGITAL NR
Use to turn the main menu on or off.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
STB (DTV) operations
• The following operations are available from the receiver’s remote control after you program your
digital tuner’s preset code, but some operations may need to be learned by the receiver (see “Setting
Up the Remote Control to Control Other Components,” p.54-57).
• To perform these operations, press the TV/SAT button to set the remote control to the SAT operation
mode.
• For more information on individual commands consult the manual that came with the component.
1
SOURCE
Î
S0 URCE
RECEIVER
Press to switch the satellite tuner on or off.
MULTI
OPERATION
SYSTEM
OFF
1
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 DTV MENU
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
Press to select the DTV menu.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
7
8
TUNING
STATION
+
¡
2
3
3 DTV ON/ OFF
1
4
¢
CHANNEL
-
+
Press to switch the DTV mode on or off.
2
5
8
0
3
1
6
9
4
4
5
4 Num ber buttons
7
Use to select satellite channels.
+1 0
DISC
DISPLAY
9
0
RF ATT
5 +10
TV
TV CONTROL
Use to select a specific TV channel.
TV VOL
VOLUME
TV FUNC
6 5¥∞¥2¥3¥ENTER
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
5¥∞¥2¥3 : Press to select or adjust items on the
menu screen.
ENTER : Press to activate the selected function.
SIGNAL
SELECT
2/ dts
6
SYSTEM
SETUP
7 ¶¥7¥3¥8 (BLUE/ GREEN/ RED/ YELLOW)
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
Use to make selections from the DTV menu.
DIGITAL NR
8 CHANNEL –/ +
Use to select a TV channel.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
9 ENTER
Use to select the channel specified with the
number buttons (not all models require this step).
VSX-D938TX
0 MENU
Use to select different menus on a DTV screen.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
TV operations
• The following operations are available from the receiver’s remote control after you program your TV’s
preset code, but some operations may need to be learned by the receiver (see “Setting Up the
Remote Control to Control Other Components,” p.54-57).
• To perform these operations, press the TV/SAT and TV CONT button to set the remote control to the
TV operation mode.
• For more information on individual commands consult the manual that came with the your TV.
1
SOURCE
Press to switch the TV on or off.
Î
RECEIVER
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
1
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
2 DTV MENU
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
Press to select the DTV menu.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
7
8
TUNING
STATION
+
¡
2
3
1
4
¢
3 DTV ON/ OFF
CHANNEL
-
+
2
5
8
0
3
1
Press to switch the DTV mode on or off.
6
9
4
4
5
4 Num ber buttons
7
Use to select a specific TV channel.
+1 0
DISC
DISPLAY
RF ATT
5 +10
TV
TV CONTROL
Use to select a specific TV channel.
TV VOL
VOLUME
TV FUNC
6 5¥∞¥2¥3¥ENTER
9
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
5¥∞¥2¥3 : Press to select or adjust items on the
menu screen.
ENTER : Press to activate the selected function.
SIGNAL
SELECT
2/ dts
6
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
7 ¶¥7¥3¥8¥1 (BLUE/ GREEN/ RED/
YELLOW)
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
Use to make selections from the DTV menu.
8 CHANNEL –/ +
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
Use to select a TV channel.
9 MENU
VSX-D938TX
Use to select different menus on a DTV screen.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control of Other Com ponents
Cassette deck operations
You can use this remote control to control most cassete decks, though with some models the functions may
differ.
• The following operations are available from the receiver’s remote control after you recall a cassette
deck’s preset code, but some operations may need to be learned by the receiver (see “Setting Up the
Remote Control to Controls Other Components,” p.54-57).
• To perform these operations, press the MD/TAPE 1 button to set the remote control to the TAPE
operation mode.
• For more information on individual commands consult the manual that came with the component.
1
SOURCE
Î
RECEIVER
S0 URCE
Press to switch the cassette deck on or off (not
possible with all models).
MULTI
SYSTEM
OFF
OPERATION
1
2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
6
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
2 7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
3
4
7
8
Press to stop playback or recording.
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
3 ¶
2
5
8
0
3
1
5
Press to start recording.
6
9
4
7
4 1¥¡
+1 0
DISC
DISPLAY
1 : Press to rewind the tape.
RF ATT
¡ : Press to fast forward the tape.
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
5 Num ber buttons (1-6)
1: 7 (Press to stop playback or recording.)
2: 3 (Press to start playback of the side of the
cassette which has been loaded as the front.)
3: 8 (Press to pause playback or recording.)
4: 1 (Press to rewind the tape.)
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
5: 2 (Press to start reverse playback.)
6: ¡ (Press to fast forward the tape.)
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
6 3
Press to start playback of the side of the cassette
which has been loaded as the front.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
7 8
VSX-D938TX
Press to pause playback or recording.
8 4
Press to start reverse playback (for auto reverse
decks).
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Recording from Audio Com ponents
The following explanations show you how to record an analog audio signal with the component you connected
to the MD/TAPE 1 or TAPE 2 MONITOR jacks. Note that you cannot record an component that is only
connected digitally. If you want to record from a digital component, it must be connected in an analog manner as
well. If you want to record a digital signal, see the next page.
The receiver’s volume, channel level, tone (BASS, TREBLE, and LOUDNESS), and surround effects
have no effect on the recorded signal and the EXTERNAL DECODER input cannot be recorded.
Î
RECEIVER
1 Select the source com ponent and put the receiver in
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
that function. Rem em ber, SIGNAL SELECT m ust be
set to analog.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
1
TUNER
TV CONT
TAPE1
MPX
7
Press the SIGNAL SELECT button on the remote control (or use the
button on the front panel) and choose ANALOG. Recording
DIGITAL or AC-3 RF (VSX-D938TX only) signals is not possible.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
2 Start recording w ith a TAPE or MD (etc.).
3 Playback the source to be recorded.
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
Record m onitor (TAPE 2 MONITOR)
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
If you connect a cassette deck (etc.) with a record monitor function to
the TAPE 2 MONITOR jacks, you can listen to the sound of the
recording as it is recorded.
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
Press TAPE 2 MONITOR to sw itch betw een the sound of
the recording (TAPE 2 indicator on) and the sound of the
source com ponent (TAPE 2 indicator off).
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Recording from Digital Audio Com ponents
The following explanations show you how to record digital audio. Using this method you can make exact digital
copies of sources like CDs or MDs. The only drawback is that you cannot switch between various recorders at
the touch of a button like you can with analog recordings (see the previous page). If you look on the back of the
VSX-D938TX/D908TX/D908TX-G, you will find a digital out jack which is marked PCM/2/DTS/MPEG (VSX-
D938TX only) OUT (it is to the right of the digital in jacks in the upper left-hand corner). If you connect this to the
optical input on a digital recorder (currently these include MD, DAT, CD-R, and DVD video recorder), you can
make direct digital recordings with this unit. Of course, the digital components you want to record all need to be
connected to the VSX-D938TX/D908TX/D908TX-G with digital inputs as well. See p.10 if you have not made
these connections.
The receiver’s volume, channel level, tone (BASS, TREBLE, and LOUDNESS), and surround effects
have no effect on the recorded signal.
Î
RECEIVER
1 Prepare the source you w ant to record and set the
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
SIGNAL SELECT to digital.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
Press the SIGNAL SELECT button on the remote control (or use the
button on the front panel) and choose DIGITAL.
MULTI CONTROL
MD/
1
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
2 Start recording w ith a CD-R or MD (etc.).
3 Playback the source to be recorded.
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
In some cases, digital recordings have copy guard protections
on them and making a digital copy is not possible. It is still
possible to copy these digital sources if you have hooked them
up with analog connections (in this case, the copies will not be
exact digital reproductions). Refer to the previous page in this
case.
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Recording from Video Com ponents
The following operations show you how to record audio and video to the video tape recorder connected to the
VCR 1 or VCR 2 jacks. Note that all signals coming out of these jacks will be analog and it is not possible to
record DTS soundtracks.
The receiver’s volume, channel level tone (BASS, TREBLE, and LOUDNESS), and surround effects have
no effect on the recorded signal.
Î
RECEIVER
1 First, decide the com ponent you w ould like to record
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
and put the receiver in that function. Set the SIGNAL
SELECT to analog.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
1
TUNER
TV CONT
TAPE1
MPX
7
Press the SIGNAL SELECT button on the remote control (or use the
button on the front panel) and choose analog. Recording DIGITAL
or AC-3 RF (VSX-D938TX only) signals is not possible.
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
2 Start recording w ith VCR 1 or VCR 2(etc.).
3 Playback the source to recorded.
6
9
4
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Multi Operations
Multi operations allow you to tell the receiver and your other components to do a number of things with the
push of just two buttons on the remote control. For example, you can program the unit to turn on your TV, turn
on your DVD player, go into a specific sound mode and start playing the loaded DVD. This feature allows you to
decide which operations you want performed as well as the order in which you want them performed.
The steps below show you how to program a string of up to 5 different operations based on eight possible
components. You do not need to program the power of this unit, or any PIONEER product, to go on, it/they will
do so automatically when the MULTI OPERATION function is used. Also, for some DVD players you will not
need to program a play command. Most DVDs will start to play automatically if their power goes on and a DVD
is loaded.
Be sure to recall or teach the rem ote control com m ands for each com ponent before attem pting
m ulti operations (see “Setting Up the Rem ote Control to Control Other Com ponents,” p. 54).
Î
RECEIVER
1 Turn on your TV and the receiver.
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
Make sure your TV is set to the appropriate video input (for
example, VIDEO 1).
1
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
3,4
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
3
2 Press REMOTE SETUP and
at the sam e tim e to
TUNING
STATION
+
¡
1
4
¢
CHANNEL
select the MULTI OPERATION SETUP m ode.
-
+
2
5
8
0
3
1
The REMOTE SETUP menu appears on your TV screen. The MULTI
CONTROL and the SYSTEM OFF buttons start to blink.
2
6
9
4
7
To cancel MULTI OPERATION SETUP m ode
Press REMOTE SETUP.
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
Multi-operation
TV VOL
VOLUME
TV FUNC
1Select an item from the
Multi-Contorol buttons.
(ex. DVD)
2Select the operation
button. (ex. DVD = MENU)
3First command has been
learned.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
4You can repeat this
proccess for 5 commands.
EXIT=Remote setup
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
2
3 Press FUNCTION that you w ant to use to start the
MULTI OPERATION.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
You can use any MULTI CONTROL button for this procedure. It
does not matter which one you choose but for example purposes
we will use the DVD/LD button.
VSX-D938TX
This MULTI CONTROL button will be used when you want to recall
the MULTI OPERATION commands for use (see the next page:
“Performing multi operations”).
Also, the SYSTEM OFF button will blink. See the next page for
instructions how to use the SYSTEM OFF button.
4 Press MULTI CONTROL for the com ponent w hose
operation you w ant to start MULTI OPERATIONS w ith
(for exam ple, TV CONT button).
The selected button will light steadily.
• Each button can perform various preset multi operations (see
step 5 on the next page).
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Î
RECEIVER
5 Press the operation, for exam ple TV (POWER), you
w ant to input.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
6-2
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
5,6-1
CLASS
BAND DIRECT ACCESS
6 Repeat steps 4 and 5 to input MULTI OPERATIONS for
the com ponents and com m ands you w ant to input.
You can also tell the receiver to go into a specific
sound m ode (THX, ADVANCED, STANDARD,
¶
-
3
-
8
+
TUNING
STATION
+
¡
6-3
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
MIDNIGHT, DSP or STEREO) by inputting that
com m and (for exam ple, see operation 4 below ).
7
+1 0
DISC
DISPLAY
RF ATT
You can repeat this process for up to five com m ands.
TV
TV CONTROL
TV VOL
VOLUME
For exam ple : you could enter the following four operations using
the preceeding steps 4 and 5.
TV FUNC
1 Press TV CONT button and TV (POWER) to turn on your TV(as
explained above).
2 Press DVD/LD then (POWER) to turn on your DVD player (if it
is not a PIONEER product).
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
3 Press DVD/LD then 3 (play) to start playing the DVD player.
4 Press ADVANCED THEATER mode to put receiver in that sound
mode. When you employ MULTI OPERATIONS (see below),
these four tasks will be performed in the same order.
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
6-4
MIDNIGHT
DSP
STEREO
7
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
7 Press REMOTE SETUP to exit the MULTI OPERATION
SETUP m ode.
VSX-D938TX
The remote control and TV return to their previous operation
modes.
Perform ing m ulti operations
Follow the procedures below to perform multi operations which you programmed in the section before this.
Î
S0 URCE
RECEIVER
1
2
1 Press MULTI OPERATION on the rem ote control.
MULTI
SYSTEM
OFF
OPERATION
The MULTI CONTROL buttons start to blink.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
2 Press MULTI CONTROL that has been set up w ith
m ulti operations.
¶
-
3
-
4
-
8
+
TUNING
STATION
+
¡
1
¢
CHANNEL
+
2
5
8
0
3
The power of the main unit goes on and the programmed multi
operations are performed automatically.
1
6
9
4
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
System OFF
The SYSTEM OFF feature allows you to tell the receiver and your other components to stop and turn off with
the push of only one button on the remote control. For example, you can program the unit to stop your DVD,
turn off your TV, turn off your DVD player and turn off the receiver itself. You do not need to program in other
the power for PIONEER components, they will go off automatically in this mode. The receiver itself will go off
automatically as well.
The steps below show you how to program a string of up to 5 different SYSTEM OFF operations based on eight
possible components.
Be sure to recall or teach the rem oto control com m ands for each com ponent before attem pting
m ulti operations (see “Setting Up the Rem ote Control to Control Other Com ponents,” p.54).
3
1 Press REMOTE SETUP and
at the sam e tim e to
1
select the MULTI OPERATION SETUP m ode.
Î
RECEIVER
The REMOTE SETUP menu appears on your TV screen. The MULTI
CONTROL and the SYSTEM OFF buttons start to blink.
To cancel MULTI OPERATION SETUP m ode
Press REMOTE SETUP.
S0 URCE
MULTI
SYSTEM
OFF
OPERATION
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
3
5-1
5-2
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
1
4
¢
2 Press SYSTEM OFF.
CHANNEL
-
+
2
5
8
0
3
1
The SYSTEM OFF button will blink.
1
6
9
4
7
3 Press MULTI CONTROL for the com ponent w hose
operation you w ant to start SYSTEM OFF w ith (for
exam ple, TV CONT button).
+1 0
DISC
DISPLAY
RF ATT
4
TV
TV CONTROL
The selected button will light steadily.
TV VOL
VOLUME
TV FUNC
4 Press the operation, for exam ple TV (POWER), you
w ant to lnput.
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
5 Repeat steps 3 and 4 to input SYSTEM OFF for the
com ponents and com m ands you w ant to input.
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
1
DIGITAL NR
You can repeat this process for up to five com m ands.
For exam ple: You could enter the following two operations using
the proceeding steps 3 and 4.
1 Press TV CONT button and TV (POWER) to turn off your TV
(as explained above).
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
2 Press DVD/LD then (POWER) to turn off your DVD player (if it
is not a PIONEER product).
VSX-D938TX
When you employ SYSTEM OFF (see below), these two tasks
will be performed in the same order.
To exit SYSTEM OFF SETUP m ode
Press REMOTE SETUP.
Using the system off button
This button will turn off the receiver and any component that has programmed into the SYSTEM OFF settings
(see above) as well as turn off all PIONEER components regardless of whether they have been programmed
into SYSTEM OFF. If you use this feature when a DVD is playing, the player will stop the play mode before
switching off.
1
1 Press SYSTEM OFF on the rem ote control.
Î
RECEIVER
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Setting Up the Direct Function
The direct function is designed in case you have an external video source connected to your TV (a video source
that is not going through the VSX-D938TX/D908TX/D908TX-G). For this explanation we will call this the “external
video deck.” You would like to control external video deck with this unit’s remote control so you have assigned
it a function button (for example purposes, the VCR 2 button). Yet, if you put the receiver in VCR 2 mode you
will get no picture on your TV because the external video deck signal is not going through the VSX-D938TX/
D908TX/D908TX-G. To get around this problem, you set the DIRECT FUNCTION for VCR 2 to OFF. Now when
you press VCR 2 function button you can control the external video deck with the remote control but the
receiver does not go into VCR 2 mode.
Î
RECEIVER
4
1 Press REMOTE SETUP and
at the sam e tim e to
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
select the DIRECT FUNCTION m ode.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
The MULTI CONTROL buttons DVD/LD, TV/SAT, VCR 1, VCR 2, CD,
and MD/TAPE 1 start to blink.
MULTI CONTROL
MD/
2
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
Direct Function
CHANNEL
-
+
You can choose whether
the commander sends a
function code or not ,
when you press each
Multi-control button.
1Select function.
2
5
8
0
3
1
3
1
6
9
4
7
+1 0
DISC
DISPLAY
2Input YES or NO.
RF ATT
TRANSMIT
YES =1
TV
TV CONTROL
NO =2
TV VOL
VOLUME
EXIT=Remote setup
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
2 Select a com ponent by pressing its MULTI CONTROL
button.
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
3 Set the DIRECT FUNCTION of each external source to
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
1,4
DIGITAL NR
NO by pressing
2
.
4 Press REMOTE SETUP to exit the DIRECT FUNCTION
m ode.
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
The default setting is all YES. If you have turned a DIRECT
FUNCTION to NO and want to turn it back to YES, follow the
directions above and press
in step 3.
1
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Rem ote back light
This function is useful for using the unit in a dark room.
Î
RECEIVER
1 Press and hold both REMOTE SETUP and
5
.
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
The remote back light strength cycles in the following order:
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
MULTI CONTROL
OFF MID MAX
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
The default setting is MAX.
2
5
8
0
3
1
1
6
9
4
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
1
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Resetting the Rem ote Control
The following operations allow you to erase the settings stored in the remote control.
Erasing the m ulti operations
Î
RECEIVER
1 Press and hold both REMOTE SETUP and
8
for m ore
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
than 3 seconds.
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
The MULTI CONTROL buttons will blink 3 times and all personal
multi operation settings will be erased.
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
1
7
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
1
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Other Functions
Erasing the learned rem ote control com m ands
Î
RECEIVER
1 Press and hold both REMOTE SETUP and
than 3 seconds.
9
for m ore
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
The MULTI CONTROL buttons will blink 3 times and all signals
which have been learned from other remote controls will be
erased.
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
¡
1
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
7
1
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
1
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
Erasing all signals learned and preset codes
Î
RECEIVER
1 Press and hold both REMOTE SETUP and
than 3 seconds.
0
for m ore
S0 URCE
MULTI
OPERATION
SYSTEM
OFF
DVD/ LD
CD
TV/ SAT
VCR1
VCR2
The MULTI CONTROL buttons will blink 3 times and all preset
codes will be erased.
MULTI CONTROL
MD/
TUNER
TV CONT
TAPE1
MPX
7
CLASS
BAND DIRECT ACCESS
¶
-
3
-
8
+
TUNING
STATION
+
1
¡
4
¢
CHANNEL
-
+
2
5
8
0
3
1
6
9
4
7
1
+1 0
DISC
DISPLAY
RF ATT
TV
TV CONTROL
TV VOL
VOLUME
TV FUNC
EFFECT
CH SEL
MENU
ENTER
MUTE
FUNCTION
/
SIGNAL
SELECT
2/ dts
SYSTEM
SETUP
THX
ADVANCED
STANDARD
MPEG
REMOTE
SETUP
MIDNIGHT
DSP
STEREO
1
DIGITAL NR
AV PREPROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VSX-D938TX
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
Dolby Digital
Dolby Digital is a compression format which records
the sound of 6 channels of the theater surround
system (Dolby Digital) on the movie film digital track.
Of the 6 channels, the sub woofer channel is
intended for bass only, and because the frequency
range is smaller than the main channel, it is
expressed as 5.1 channel.
Laser disc form at
Laser discs are now available on the market in large
numbers. This means that the recording of different
format audio signals on the laser disc raises the
important question of compatibility with existing
laser discs. Dolby Digital tracks on Laser discs record
signals using the space of one analog audio channel
so it will maintain compatibility with existing discs
and players.
As shown in the following figure, the digital audio
sounds of Dolby Digital discs can be played back as
currently done. Analog sounds are played back by
using the other channel without the Dolby Digital
signals for monaural audio signals.
Dolby Digital is the name of the Dolby surround
multi-channel digital system that was developed
after the Dolby Surround System and Dolby Pro
Logic Surround System.
5.1 channel digital
surround track
4 channel analog
sound track (Matrix)
Dolby Digital
sound
Analog sound
(Monaural)
Video
Digital
sound
2
4
6
8
10
12
14 MHz
Frequency
Dolby
Digital
encoding
Com parison w ith Dolby Pro Logic
Surround
Dolby Digital for m ovie film s
Dolby Digital is also known as the 5.1 channel
system. It is equipped with 5 channels (front left,
front right, center, surround left, surround right) in
the frequency range from 20 Hz to 20 kHz and an
independent Low Frequency Effect (LFE) channel.
The sub woofer channel is also called Low
Frequency Effect (LFE).
The sub woofer channel can be used as desired to
enjoy strong bass sounds.
The table on the next page shows the comparison
with Dolby Pro Logic Surround effects.
The number of movies made using Dolby Digital
since 1992 has exceeded 300 and continues to
increase. For compact disc players and laser disc
digital sounds, 16 bits are used to sample the original
analog audio waveform and sampling is carried out
44,100 times every second. However, because an
enormous amount of recording signal data is
required for the multi channel system with this
method, AC-3 is used to compress the data.
In reproducing audio signals, the smaller the bit
number used, the lower the sound quality. With AC-
3, drop in auditory sound quality is prevented by
using masking technology and digital filtering
technology based on the human auditory
characteristics.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
DTS
DTS has been adopted as a sound recording format in the latest movie theaters since the release of “JURASSIC
PARK” in 1993, and has a good reputation for high quality sound and dynamic surround effects.
In this system, 6 channels of digital sound are recorded on CD-ROM, rather than on the film. DTS adopts a
simultaneous playback format. With a low rate of compression of sound signals and a high rate of transmittance,
a higher sound quality format is produced. Also, unlike the process of recording digital sounds on film directly,
the only components required are a CD-ROM player as might be used with a personal computer and a DTS
processor, and therefore less investment is required than with other formats. For this reason, the format is
being introduced in more and more movie theaters, and is being adopted in home movie software (DVD, LD)
and music software (5.1 channel CD).
More than 11,000 movie theaters around the world have adopted the DTS format, which is now the most
popular digital format for movie theaters, especially in U.S.A, Europe, and Asia.
DTS
Dolby Pro Logic
Surround
Dolby Digital
6 channels (Max.)
6 channels (Max.)
2 channels
No. of recorded
channels
5.1 channels (Max.)
5.1 channels (Max.)
4 channels
No. of playback
channels
Front Left, Front Right,
Center, Surround Left,
Surround Right, Sub
Woofer
Front Left, Front Right,
Center, Surround
Playback channel
structure
Front Left, Front Right,
Center, Surround Left,
Surround Right, Sub
Woofer
Digital discrete
processing
Analog matrix
processing
Sound processing
Digital discrete
processing
20,000 Hz
7,000 Hz
Rear (Surround) high
frequency playback
limit
20,000 Hz
• 6 completely
independent
channels
Other
• 5.1 completely
independent
channels
• High dynamic range
• Stable position, high
phase characteristics,
and advanced
surround effects
reproduction
• Low compression
rate
(about one-fourth),
high quality sound
• High dynamic range
• Stable position, high
phase characteristics,
and advanced
surround effects
reproduction
• High efficiency
(Compression rate of
about one-tenth)
Warning about DTS test m ode
The VSX-D938TX/D908TX/D908TX-G has a mode for PIONEER repairmen to test the DTS sound quality. You will
never need to access this mode. Rather you should be careful NOT to put the receiver in this mode because
doing so will erase all your setup parameters like speaker settings, delay settings, channel settings, etc.
STANDBY/ON
In STANDBY m ode, holding the DIRECT button and
pressing the STANDBY/ ON button w ill put the receiver in
DTS test m ode. Be careful NOT to do this.
DIRECT
VSX-D938TX
The above described method is similar to choosing either PAL or NTSC
video setting and choosing 8 Ω or 6 Ω setting so be particularly careful
when performing these operations noy to accidentally put the receiver in
DTS test mode.
If you accidentally put the receiver in DTS test mode, repeat the
same procedure (as above) to put the receiver back in a usable
mode. After this you will need to reset your setup parameters
(speaker settings, delay settings, channel settings, etc.).
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
THX
TM
THX is a Lucasfilm, Ltd. program dedicated to
maximum accuracy in movie presentation. Movie
sound tracks are recorded in large movie dubbing
stages using movie theater equipment. For a sound
track to be presented accurately in your home,
special technologies are required. In your home the
room is much smaller and has a bright sound, the
speakers are very different and there are only six of
them, plus, you sit much closer to each one of those
speakers. Because of these differences we often
miss the power and emotion that thrills us in a good
movie. Now Pioneer and THX have teamed up to
bring the full glory of accurate cinema sound to the
comfort and convenience of your home.
Tim bre Matching
: When recording a sound track
it is very important that the surround sounds move
smoothly and seamlessly around the theater. It is
very distracting when sounds seem to jump from
speaker to speaker.
Timbre Matching helps to smooth the movement of
the surround sounds even though you are using only
two speakers.
TM
Bass Peak Level Manager
: Some Dolby Digital
and DTS soundtracks can produce bass peaks that
are undesiable in a home theater environment. The
Bass Peak Level Manager allows you to set the
maximum peak levels appropriate to your system.
(Set this function according to the bass peak level
instructions on page 35.)
Re-Equalization TM : In a theater the room is very
large and dead sounding, you sit a long way back
from the speakers and the speakers themselves are
very specialized. Because a sound track recorded in
this dead sounding space when it is played at home
it sounds overbright. THX Re-Equalization adjusts for
this difference in a very precise way.
TM
Loudspeaker Position Tim e Synchronization
This feature allows you to adjust for the difference in
the distance from each individual loudspeaker to the
listening position. Doing this ensures that all the
speakers operate in precise synchronization
improving the seamless nature of the soundfield.
(Set this function according to the channel delay
instructions on page 31.)
:
TM
Dynam ic Decorrelation
: When a sound track
sends mono sound to the surround speakers it often
seems to be coming come from one side instead of
from all around you as it would in a theater. Dynamic
Decorrelation helps to correct this inaccuracy.
MPEG Audio (VSX-D938TX only)
MPEG is an audio encoding system which delivers high quality audio for music and movies. By removing
frequencies which are out of the human hearing range, the sound is then compressed to enable the
transmission of mono, stereo, or multichannel (5.1 and 7.1) audio in a single bitstream which is why it has
become a standard audio format for DVD an personal computers. The composition and versatility of MPEG audio
also ensures that the presentation of a multichannel soundtrack will sound appropriate on everything from a 7.1
channel surround sound home theater setup to a mono televition set. Above all, MPEG audio is designed to be
compatible with past and future MPEG audio versions, which means that future versions of MPEG audio will be
compatible with decoders currently being produced (the signal is merely reconfigured to fit the number of
channels available in a system).
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
Preset Code List
VSX-D938TX
Device
Manufacturer
Code
Device
Manufacturer
Code
DVD
TOSHIBA
SONY
PANASONIC
JVC
SAMSUNG
SHARP
AKAI
001
002
003
004
005
006
007
009
VCR
CROWN
DAEWOO
DANSAI
DE GRAAF
DECCA
418, 423, 425
418,423
425
406
414, 419
417
410, 414, 419
425
419
410, 414
406, 410, 414, 419
405, 409, 411, 424,
425
410
423
419
DUAL
DUMONT
ELCATECH
FIDELITY
FINLANDIA
FINLUX
RCA
PIONEER
000, 008
LD
DENON
HITACHI
PHILIPS
RADIOLA
SONY
TELEFUNKEN
PIONEER
106
105
104
104
FIRSTLINE
FISHER
FRONTECH
FUNAI
101,103
100
100, 102 (DVD code)
GBC
414
423
411
SAT
PIONEER
PIONEER
200, 202
500
GENERAL
GOLDSTAR
GOODMANS
TUNER
VCR
411, 418, 419, 423,
425
410, 417
410, 414
430
411, 419, 425
425, 426
412, 413, 425, 426
425
PHILIPS
PANASONIC
THOMSON
SONY
JVC
GRUNDIG
414, 428
403, 408
417, 420, 428
416, 417
407, 417, 428
408, 414, 419, 425,
426, 427
GRAETZ
GRANADA
GRANDIENTE
GRANDIN
HCM
HINARI
AKAI
HITACHI
TOSHIBA
401,417
HYPSON
IMPERIAL
INTERFUNK
ITT
ITV
KAISUI
KENDO
KORPEL
LEYCO
LOEWE
LUXOR
M-ELECTRONIC
MANESTH
MARANTZ
MATSUI
MEMOREX
MEMPHIS
METZ
MINERVA
MULTITECH
MURPHY
NBC
NECKERMANN
NESCO
NORDMENDE
OCEANIC
OSAKI
OTTO VERSAND
PALLADIUM
PATHE MARCONI
PENTAX
406, 417, 419
405, 409, 414, 417,
428
407, 409, 414
402
412, 413, 424
410
417, 420, 421
403, 408, 417, 427
401, 410, 417
417
413,419
425
413, 415, 418, 423,
424
423
419
425
411, 414
419
414
401, 410, 417, 428
411, 418
425
401, 424
425
MITSUBISHI
SHARP
ORION
SANYO
FERGUSON
BLAUPUNKT
NOKIA
SELECO
AIWA
425
411, 414
401, 409, 410
419
405, 425
414
412, 413, 424
410, 411, 419
425
403, 427
427
419, 425
419
407, 417
414
AKIBA
ALBA
AMBASSADOR
AMSTRAD
ANITECH
ASA
BAIRD
410, 417, 419, 421
418, 423, 425
420, 422
BASIC LINE
BRANDT
BRANDT
ELECTRONIQUE
BUSH
417
425
417, 428
417, 419
411, 419, 425
414
411, 417, 425
417
413, 415, 418, 424,
425
423
419
425
423
423
CATRON
CGB
CIMLINE
CLATRONIC
CONDOR
406
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
VSX-D938TX
Device
Manufacturer
Code
Device
Manufacturer
Code
VCR
PERDIO
419
414
423
419, 426
414
414
414
417, 428
411, 418, 425
417, 420, 428
412, 424
401, 409
407, 417
414
417, 419
414, 419, 425
414
423
425
410, 411, 427
405
414
423
419
419
419
414, 417, 419
423
TAPE
YAMAHA
PIONEER
811, 816
800, 819
PHONOLA
PORTLAND
PROLINE
PYE
QUELLE
RADIOLA
REX
ROADSTAR
SABA
SAISHO
SALORA
SANSUI
SBR
SCHAUB LORENZ
SCHNEIDER
SEI
SENTRA
SHINTOM
SIEMENS
SINGER
SINUDYNE
SOLAVOX
SUNSTAR
SUNTRONIC
TASHIKO
TATUNG
TEC
TELEAVIA
TELEFUNKEN
TENOSAL
TENSAI
CD
AKAI
ARCAM
ASUKA
AUDIO TON
BUSH
CALIFORNIA
AUDIO LAB
CYRUS
DENON
DUAL
308
312
313
312
305
304
312
309
313, 319
317
302
312
307
313
303
310, 311
322
312
318
323
304, 312
312
304
300
312
308
316
312
320
304
312, 322
312
304
323
312
319
317
FISHER
GOLDSTAR
GRUNDIG
HITACHI
INTERSOUND
JVC
KENWOOD
KODAK
LINN
LUXMAN
M ELECTRONIC
MARANTZ
MATSUI
MCS
MEMOREX
MERIDIAN
MITSUBISHI
NAD
NAIM
ONKYO
PANASONIC
PHILIPS
QUAD
417
417, 420, 422, 428
425
419
410, 417
401, 411, 414, 419,
427
425
425
423
THORN
UNIVERSUM
YAMISHI
YOKAN
YOKO
QUASER
ROADSTAR
ROTEL
SABA
SANYO
PIONEER
400, 404, 407, 431,
(DVD Video
Recorder), 414
SHARP
321
TAPE
AKAI
ARCAM
DENON
FISHER
GRUNDIG
JVC
KENWOOD
LUXMAN
MARNATZ
MEMOREX
MITSUBISHI
NAKAMICHI
ONKYO
823
810
810, 821
813
815
802
804, 807, 816
805
815
819
823
806
808, 812
815
818
809
801, 817
814
803
SONY
301, 316
304, 306
319
319
312
314, 315
300, 325
(CD-Recorder)
TECHNICS
TELEFUNKEN
THOMSON
UNIVERSUM
YAMAHA
PIONEER
TV
PHILIPS
SONY
601, 607, 610, 636
604
601, 632
601, 608, 620, 622
605, 632
612, 614, 631
602
607, 615, 623, 625
601, 606, 610, 612,
620, 621, 633, 637
601, 612, 620, 630
612
GRUNDIG
PANASONIC
TOSHIBA
TELEFUNKEN
SHARP
PHILIPS
SANSUI
SHERWOOD
SONY
TANDBERG
TECHNICS
TOSHIBA
SAMSUNG
HITACHI
SABA
BRANDT
820, 822
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
VSX-D938TX
Device
Manufacturer
Code
Device
Manufacturer
Code
TV
SANYO
611, 624, 627
612, 630, 631
607, 612, 630
603, 620, 631
601, 609
607, 619, 626
607, 629
601
603, 612, 630, 631
607
613
607, 623, 636
TV
FISHER
603, 611, 615, 624
603, 607, 620
601, 620, 625
603
THOMSON
FERGUSON
NOKIA
MITSUBISHI
SCHNEIDER
GOLDSTAR
BLAUPUNKT
NORDMENDE
RADIOLA
JVC
FORMENTI
FRONTECH
FRONTECH/
PROTECH
FUJITSU
FUNAI
GBC
GEC
GELOSO
GENEXXA
GOODMANS
627
617, 625
603, 620
607, 610, 627
603, 623
601, 619
607, 616, 626, 627,
636
DAEWOO
ORION
603, 607, 616, 617
SIEMENS
ACURA
601
623
GORENJE
GPM
615
619
ADMIRAL
AKAI
AKURA
601
603, 611, 620
619
GRAETZ
GRANADA
601, 620
607, 611, 620, 621,
627
ALBA
607, 616, 619, 623
620, 623, 626
623
624
619
607, 612
619, 623
601, 607, 620
615
607
619
618
618
619
GRANDIENTE
GRANDIN
HANSEATIC
HCM
639
618
607, 620
618, 623
607, 619, 623
618
AMSTRAD
ANITECH
ASA
ASUKA
HINARI
AUDIOGONIC
BASIC LINE
BAUR
BEKO
BEON
BLUE SKY
BLUE STAR
BPL
BTC
BUSH
HISAWA
HUANYU
HYPSON
ICE
IMPERIAL
INDIANA
INGELEN
INTERFUNK
INTERVISION
ISUKAI
636
607, 618, 625
625, 626
615, 620
607
601
601, 603, 607, 620
625, 628
619
607, 619, 620, 623,
626, 636
ITC
620
CASCADE
CATHAY
CENTURION
CGB
623
607
607
620
623
607
615
615
623
603
615, 623
620
619
619
607
623
ITT
JEC
KAISUI
KAPSCH
KENDO
KENNEDY
KORPEL
KOYODA
LEYCO
LIESENK&TTER
LUXOR
601, 603, 620
605
618, 619, 623
601
620
603, 620
607
623
607, 617, 625, 627
607
603, 620, 621
601, 623, 624, 633,
635, 636
607, 612, 630
603, 628
628
616, 625
607
607
CIMLINE
CLARIVOX
CLATRONIC
CONDOR
CONTEC
CROSLEY
CROWN
CRYSTAL
CYBERTRON
DAINICHI
DANSAI
DAYTON
DECCA
M ELECTRONIC
M-ELECTRONIC
MAGNADYNE
MAGNAFON
MANESTH
MARANTZ
MARK
607, 627
607, 623
632
DIXI
DUMONT
ELIN
ELITE
ELTA
EMERSON
ERRES
FINLANDIA
FINLUX
607
619
623
620
MATSUI
607, 616, 617, 620,
623, 626, 627
610
607
623
MCMICHAEL
MEDIATOR
MEMOREX
METZ
MINERVA
MULTITECH
NECKERMANN
607
611, 621, 635
603, 607, 624, 627,
632, 633, 635
617, 623
601
601, 632
623, 628
601, 607
FIRSTLINE
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
VSX-D938TX
Device
Manufacturer
Code
Device
Manufacturer
Code
TV
NEI
NIKKAI
607, 620
605, 607, 619, 625,
627
628
601, 603, 620
619, 625, 627
TV
SONOKO
SONOLOR
SONTEC
SOUNDWAVE
STANDARD
STERN
607, 623
601, 611
607
607
619, 623
601
NOBLIKO
OCEANIC
OSAKI
OSO
OSUME
619
627
SUSUMU
SYSLINE
TANDY
TASHIKO
TATUNG
TEC
TELEAVIA
TELETECH
TENSAI
619
607
601, 619, 627
610
607, 627
620
612
623
617, 619
601, 607, 620, 624,
627
618
OTTO VERSAND
PALLADIUM
PANAMA
PATHO CINEMA
PAUSA
601, 603, 607, 620
615
625
620
623
603, 620
603
PHILCO
PHOENIX
PHONOLA
PROFEX
607
THORN
620, 623
607, 620, 623, 625,
628
PROTECH
TOMASHI
TOWADA
620
QUELLE
601, 603, 607, 620,
624, 632
607
ULTRAVOX
UNIVERSUM
603, 620, 628
601, 607, 615, 620,
624, 625, 633, 635
R-LINE
RBM
632
VESTEL
607
REDIFFUSION
REX
603, 620
601, 625
619, 623, 625
616, 623, 625
601, 603, 620, 621
628
VOXSON
WALTHAM
WATSON
WATT RADIO
WHITE
WESTINGHOUSE
YOKO
601
621
607
603, 620, 628
607
ROADSTAR
SAISHO
SALORA
SAMBERS
SBR
SCHAUB
LORENZ
SEG
607, 610
620
607, 620, 625
600, 601, 603, 607,
612, 620, 630
PIONEER
620, 625
603, 617, 628
601, 620
603, 628
603, 616, 617, 628
621
MD
SONY
KENWOOD
SHARP
901
903
902
904
905
906
900, 902
SEI
SELECO
SIAREM
SINUDYNE
SKANTIC
SOLAVOX
TEAC
ONKYO
DENON
PIONEER
601
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
VSX-D908TX/ D908TX-G
Device
Manufacturer
Code
Device
TAPE
CD
Manufacturer
Code
DVD
TOSHIBA
SONY
PANASONIC
001
002
003
004
005
006
007
009
PIONEER
800
SONY
301, 316, 317, 318
304, 326
310, 321, 311
309
302, 319, 313
312, 322
TECHNICS
KENWOOD
DENON
RCA
PHILIPS
YAMAHA
JVC
JVC
SAMSUNG
SHARP
AKAI
RCA
PIONEER
315, 314, 328
303
000, 008
LD
SONY
101
105, 106
103
104
100
107
100
TEAC
305, 306, 327, 324,
325
320, 308, 307
323, 312, 324
313
PANASONIC
KENWOOD
PHILIPS
MITSUBISHI
RCA
ONKYO
MARANTZ
SANYO
OPTIMUS
PIONEER
300
300,329
PIONEER
102 (DVD code)
(CD-Recorder)
SAT
VCR
RCA
SONY
PIONEER
201 (SAT), 203 (SAT)
202 (SAT)
200 (SAT), 204
MD
TV
SONY
KENWOOD
SHARP
901
903
902
904
905
906
900, 902
(Digital Tuner)
TEAC
ONKYO
DENON
PIONEER
RCA
401, 406, 408, 414,
405, 413, 411, 415
403, 404, 417
414, 408, 426, 403
410, 426, 412, 427,
425, 420
ZENITH
MAGNAVOX
FISHER
RCA
601, 610, 615, 616,
617, 618
603, 620
ZENITH
PANASONIC
TOSHIBA
JVC
408, 432, 433
405, 409, 426
428, 430, 429, 408,
414, 431, 407
408, 401, 406, 436,
434
416, 417, 404, 408
409, 420, 421, 422,
423, 424, 408
407
MAGNAVOX
607, 610, 603, 612,
629
601, 608, 607, 610,
617, 602, 628
618
608, 622, 607
604
605, 602, 626, 621
609, 610, 602, 621
606, 610, 624, 625,
618
GE
HITACHI
PANASONIC
SONY
TOSHIBA
MITSUBISHI
HITACHI
SONY
MITSUBISHI
SANYO
SHARP
GOLDSTAR
OPTIMUS
410, 412, 425, 435
402, 418, 419
411, 409
JVC
SHARP
SANYO
613, 623
602, 619, 627
621, 614
408, 432, 433, 402,
418, 419
452
400, 453 (DVD Video
Recorder)
PHILIPS
GOLDSTAR
RADIO
607
GRANDIENTE
PIONEER
610, 623, 621, 602
610, 623, 621, 602
SHACK
GRANDIENTE
PIONEER
635
600
TAPE
SONY
801, 806
803
804, 807
805
TECHNICS
KENWOOD
TEAC
DENON
ONKYO
YAMAHA
JVC
CATV
JERROLD
711, 701, 702, 712,
704, 713, 703, 714,
716,715
705, 706, 708, 709
707, 717, 710
700
810
809, 808
811, 812
802
S.ATLANTA
ZENITH
PIONEER
FISHER
OPTIMUS
813
800
TUNER
PIONEER
500
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate
the other components and electrical appliances being used. If the trouble cannot be rectified even after
exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry
out repair work.
Sym ptom
Cause
Rem edy
The power does not turn ON.
• The power plug is disconnected. • Connect the power plug to the wall
outlet.
• The protection circuit may have
been activated.
• Disconnect the power plug from
the outlet, and insert again.
The unit does not respond when the • Static electricity caused by dry air. • Disconnect the power plug from
buttons are pressed.
the outlet, and insert again.
No sound is output when a function • Improper connections.
is selected.
• Make sure the component is
connected correctly (see p. 8-17).
• Press MUTE on the remote control.
• Adjust MASTER VOLUME.
• Press the TAPE 2 MONITOR
button.
• Sound is muted.
• The volume is turned down.
• The TAPE 2 MONITOR is ON.
• Speakers are turned OFF.
• Press SPEAKERS (A/B) to select
the speakers you connected.
• Set SIGNAL SELECT (see p. 44)
• DIGITAL/ANALOG switch is set
incorrectly.
No image is output when a function • Improper connections.
is selected.
• Make sure the component is
connected correctly (see p. 8, 9).
• Press the correct function button.
• The input source is not properly
selected.
Considerable noise in radio
broadcasts.
• Incorrect frequency.
• Tune in the correct frequency.
• Connect the antenna (see p.13).
• Route AC-3 RF and digital cables
away from the antenna terminals
and wires.
• The antenna is not connected.
• AC-3 RF and/or digital cables are
near the antenna terminals and
wires.
FM broadcasts
• The FM antenna is not fully
extended or is poorly positioned.
• Fully extend the FM wire antenna,
position for best reception, and
secure to a wall.
• Weak radio signals.
• Connect an outdoor FM antenna
(see p.13).
AM broadcasts
• The AM antenna is poorly
positioned.
• Adjust the direction and position for
best reception.
• Weak radio signals.
• Connect an additional internal or
external AM antenna (see p.13).
• Turn off the equipment causing the
noise or move it away from the
receiver.
• Interference caused by other
equipment (fluorescent lamp,
motor, etc.).
• Place the antenna farther away
from the equipment causing the
noise.
Broadcast stations cannot be
selected automatically.
• Weak radio signals.
• Connect an outdoor antenna (see
p.13).
Sub woofer output is very low.
• Settings route signal away from
Sub woofer.
• To get more signal to the sub
woofer set it to PLUS or choose
SMALL for the FRONT speakers.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
Cause Rem edy
Sym ptom
No sound from surround or center
speakers.
• Speaker settings are incorrect.
• See “Speaker setting” on p.29-30
to check the speaker setting.
• The surround and/or center levels • See “Channel level” on p.32 to
are turned down.
• The surround and/or center
speakers are disconnected.
check the speaker levels.
• Connect the speakers (see
p.14,15).
Sound is produced from some
components, but not from digital
components.
• SIGNAL SELECT is set incorrectly. • Set SIGNAL SELECT to “DIGITAL”
or “ANALOG” according to the
type of connections made (see p.
44).
• The digital inputs are assigned
incorrectly, or not at all.
• Set the digital input settings
correctly (see p.10, 37).
No sound is output or a noise is
output when software with DTS is
played back.
• SIGNAL SELECT is set to
“ANALOG”.
• Make digital connections (see p.10-
11) and set SIGNAL SELECT to
“DIGITAL” (see p.44).
• A DVD player not compatible with • Refer to the instruction manual
DTS is used, or the setting of the
DVD player is incorrect.
supplied with the DVD player.
• The digital output level has been • Set the digital volume level of the
turned down on a CD player or
other component equipped with
digital output level adjustment
capability. (The DTS signal has
been altered by the player, and
cannot be read.)
player to full, or to the neutral
position.
The sound is output intermittently
when software with DTS is played
back. The overload indicator is lit.
• Disc being played back has a huge • Use the STANDARD mode to get
amount of information on it. the best results (see p.41).
When a search is performed by a
DTS compatible CD player during
playback, noise is output.
• The search function performed by • This is not a malfunction, but be
the player interferes with the
reading of digital information.
sure to turn the volume down to
prevent the output of loud noise
from your speakers.
Cannot be remote controlled.
• The remote control batteries have • Replace the batteries (see p.7).
worn out.
• Too far away or bad angle of
operation.
• Operate within 7 m, 30° of the
remote sensor on the front panel
(see p.7).
• There is an obstacle between the • Remove the obstacle or operate
receiver and the remote control.
• Strong light such as fluorescent
light is shining onto the unit’s
remote control signal light-receiving
window.
from another position.
• Avoid exposing the remote sensor
on the front panel to direct light.
• A cord is connected to the
CONTROL IN terminal on this unit.
• The IR -Receiver type is
• Connect cord to the correct jack.
• Disconnect the IR Receiver from
the rear panel, and set to the other
IR Receiver type.
mismatched with the setting.
The display is dark.
• The FL DIMMER button is pushed. • Press FL DIMMER on the front
panel repeatedly to return to the
default setting.
If the unit does not operate norm ally due to external effects such as static electricity
Disconnect the power plug from the outlet and insert again to return to normal operating conditions.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
Specifications
VSX-D938TX: (Singapore m odel)
FM Tuner Section
Continuous Power Output (STEREO MODE)
Front ....... 110 W + 110 W (DIN; 1kHz, T.H.D 1% , 8 Ω)
Frequency Range ......................... 87.5 MHz to 108 MHz
Usable Sensitivity ...... Mono: 15.2 dBf, IHF (1.6 µV/75 Ω)
50 dB Quieting Sensitivity ....................... Mono: 20.2 dBf
Stereo: 41.2 dBf
Signal-to-Noise Ratio ................. Mono: 76 dB (at 85 dBf)
Stereo: 72 dB (at 85 dBf)
Distortion ...................................... Stereo: 0.6 % (1 kHz)
Alternate Channel Selectivity ................. 70 dB (400 kHz)
Stereo Separation ...................................... 40 dB (1 kHz)
Frequency Response ............... 30 Hz to 15 kHz (± 1) dB
Antenna Input ....................................... 75 Ω unbalanced
Continuous Power Output (SURROUND MODE)
Front ....... 110 W + 110 W (DIN; 1kHz, T.H.D 1% , 8 Ω)
Center ................... 110 W (DIN; 1kHz, T.H.D 1% , 8 Ω)
Surround ............................................. 110 W + 110 W
(DIN; 1kHz, T.H.D 1% , 8 Ω)
Rated Power Output .............................. 100 W + 100 W
(20Hz–20kHz 0.09% , 8 Ω)
Input (Sensitivity/Impedance)
PHONO MM .............................................. 4.7 mV/47 kΩ
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,
MD/TAPE 1, TAPE 2 .............................. 335 mV/47 kΩ
Frequency Response
AM Tuner Section
Frequency Range ........ 531 kHz to 1,620 kHz(9kHz step)
Sensitivity (IHF, Loop antenna) ......................... 350 µV/m
Selectivity ............................................................... 25 dB
Signal-to-Noise Ratio .............................................. 50 dB
Antenna ...................................................... Loop antenna
PHONO MM ....................... 20 Hz to 20,000 Hz ±0.3 dB
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,
+0
–3
MD/TAPE 1, TAPE 2 ............. 5 Hz to 100,000 Hz dB
Output (Level/Impedance)
Miscellaneous
Power Requirements
Singaporean model ................. 220-230V AC, 50/60Hz
Power Consumption
Singaporean model ........................................... 400 W
Power Consumption in Standby mode .................. 1.0 W
AC Outlet
SWITCHED (×2) ................................ Total 100 W MAX
UNSWITCHED ......................................... 100 W MAX
Dimensions .................. 420 (W) × 173 (H) × 470 (D) mm
Weight (without package) .................................... 16.2 kg
VCR 1 REC, VCR 2 REC, MD/TAPE 1 REC, TAPE 2 REC
......................................................... 335 mV/2.2 kΩ
Tone Control
BASS ................................................... ± 6 dB (100 Hz)
TREBLE ............................................... ± 6 dB (10 kHz)
LOUDNESS .............................. +3 dB (100 Hz/10 kHz)
Signal-to-Noise Ratio [DIN(Continuous power output/50 mW]*
PHONO MM ............................................. 68 dB/61dB
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD, MD/TAPE 1,
TAPE 2 ...................................................... 92 dB/62 dB
VIDEO Section
Input (Sensitivity/Impedance)
Furnished Parts
FM Antenna ................................................................... 1
AM Loop Antenna .......................................................... 1
Dry Cell Batteries (SIZE “AA” (IEC LR6)) ....................... 2
Remote Control Unit ...................................................... 1
Operating Instructions ................................................... 1
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO ....... 1 Vp-p/75 Ω
Output (Level/Impedance)
VCR 1, VCR 2, MONITOR ......................... 1 Vp-p/75 Ω
Frequency Response
VCR 1, VCR 2, MONITOR .... 5 Hz to 100,000 Hz
Signal-to-Noise Ratio .............................................. 65 dB
–3
+0 dB
NOTE:
*
Direct: ON
Specifications and the design are subject to possible
modifications without notice, due to improvements.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Techno Tidbits and Problem -solving
FM Tuner Section
Frequency Range ......................... 87.5 MHz to 108 MHz
Usable Sensitivity ...... Mono: 13.2 dBf, IHF (1.3 µV/75 Ω)
50 dB Quieting Sensitivity ....................... Mono: 20.2 dBf
Stereo: 38.6 dBf
VSX-D938TX (Taiw an m odel)/ D908TX/
D908TX-G:
Continuous Power Output (STEREO MODE)
Front ....... 110 W + 110 W (DIN; 1kHz, T.H.D 1% , 8 Ω)
Signal-to-Noise Ratio ................. Mono: 73 dB (at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Continuous Power Output (SURROUND MODE)
Front ....... 110 W + 110 W (DIN; 1kHz, T.H.D 1% , 8 Ω)
Center ................... 110 W (DIN; 1kHz, T.H.D 1% , 8 Ω)
Surround ............................................. 110 W + 110 W
(DIN; 1kHz, T.H.D 1% , 8 Ω)
Distortion ...................................... Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity ................. 60 dB (400 kHz)
Stereo Separation ...................................... 40 dB (1 kHz)
Frequency Response ............... 30 Hz to 15 kHz (± 1) dB
Antenna Input ....................................... 75 Ω unbalanced
Rated Power Output .............................. 100 W + 100 W
(20 Hz–20 kHz 0.09% , 8 Ω)
Input (Sensitivity/Impedance)
AM Tuner Section
PHONO MM .............................................. 4.7 mV/47 kΩ
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,
MD/TAPE 1, TAPE 2 .............................. 335 mV/47 kΩ
Frequency Response
Frequency Range
VSX-D938TX (Taiwan model) ........................................
531 kHz to 1,620 kHz(9 kHz step)
VSX-D908TX/D908TX-G ...............................................
531 kHz to 1,620 kHz(9 kHz step)
PHONO MM ....................... 20 Hz to 20,000 Hz ±0.3 dB
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD,
530 kHz to 1,700 kHz(10 kHz step)
+0
–3
MD/TAPE 1, TAPE 2 ............. 5 Hz to 100,000 Hz dB
Sensitivity (IHF, Loop antenna) ......................... 350 µV/m
Selectivity ............................................................... 25 dB
Signal-to-Noise Ratio .............................................. 50 dB
Antenna ...................................................... Loop antenna
Output (Level/Impedance)
VCR 1 REC, VCR 2 REC, MD/TAPE 1 REC, TAPE 2 REC
......................................................... 335 mV/2.2 kΩ
Tone Control
BASS ................................................... ± 6 dB (100 Hz)
TREBLE ............................................... ± 6 dB (10 kHz)
LOUDNESS .............................. +3 dB (100 Hz/10 kHz)
Signal-to-Noise Ratio (IHF, short circuited, A network)
PHONO MM ...................................................... 80 dB
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD, MD/TAPE 1,
TAPE 2 ................................................................ 97 dB
Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]
Miscellaneous
Power Requirements
VSX-D938TX (Taiwan model) ......... AC 110 V, 50/60 Hz
VSX-D908TX/D908TX-G ...............................................
AC 110/120-127V/220V/240V (Switchable), 50/60 Hz
Power Consumption ........................................... 1000 W
Power Consumption in Standby mode .................. 1.0 W
AC Outlet
SWITCHED (×2) ................................ Total 100 W MAX
UNSWITCHED ......................................... 100 W MAX
Dimensions .................. 420 (W) × 173 (H) × 470 (D) mm
Weight (without package)
PHONO MM ...................................................... 80 dB
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO, CD, MD/TAPE 1,
TAPE 2 ................................................................ 83 dB
VIDEO Section
Input (Sensitivity/Impedance)
VSX-D938TX (Taiwan model) ............................ 16.2 kg
VSX-D908TX/D908TX-G ................................... 15.2 kg
VCR 1, VCR 2, DVD/LD, TV/SAT, VIDEO ....... 1 Vp-p/75 Ω
Output (Level/Impedance)
VCR 1, VCR 2, MONITOR ......................... 1 Vp-p/75 Ω
Furnished Parts
FM Antenna ................................................................... 1
AM Loop Antenna .......................................................... 1
Dry Cell Batteries (SIZE “AA” (IEC LR6)) ....................... 2
Remote Control Unit ...................................................... 1
Operating Instructions ................................................... 1
Frequency Response
+0
–3
VCR 1, VCR 2, MONITOR .... 5 Hz to 100,000 Hz dB
Signal-to-Noise Ratio .............................................. 65 dB
NOTE:
Specifications and the design are subject to possible
modifications without notice, due to improvements.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Pow er cord CAUTION!
Maintenance of External Surfaces
Handle the power cord by the plug. Do not pull
out the plug by tugging the cord and never
touch the power cord when your hands are
wet as this could cause a short circuit or
electric shock. Do not place the unit, a piece of
furniture, etc., on the power cord, or pinch the
cord. Never m ake a knot in the cord or tie it
with other cords. The power cords should be
routed such that they are not likely to be
stepped on. A dam aged power cord can cause
a fire or give you an electrical shock. Check the
power cord once in a while. When you find it
dam aged, ask your nearest PIONEER
• Use a polishing cloth or dry cloth to wipe
off dust and dirt.
• When the surfaces are dirty, wipe with a
soft cloth dipped in som e neutral cleanser
diluted five or six tim es with water, and
wrung out well, and then wipe again with a
dry cloth. Do not use furniture wax or
cleaners.
• Never use thinners, benzine, insecticide
sprays or other chem icals on or near this
unit, since these will corrode the surfaces.
authorized service center or your dealer for a
replacem ent.
Published by Pioneer Electronic Corporation.
Copyright © 1999 Pioneer Electronic Corporation.
All rights reserved.
PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS [USA] INC. P.O. BOX 1540, Long Beach, California 90801-1540, USA
PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
PIONEER ELECTRONIC [EUROPE] N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: 03-9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. San Lorenzo Num 1009 3er piso Desp. 302 Col. Del Valle, Mexico D.F. C.P. 03100 TEL: 5-688-52-90
Printed in J apan
<ARE7213-A>
<99E00EF0P00>
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Pelco Security Camera AV2100 User Manual
Pelco Security Camera C2910M C User Manual
Philips Battery Charger LR6EB8A User Manual
Philips Cordless Telephone CD4402B User Manual
Pioneer Portable DVD Player AVH X6500DVD User Manual
Plantronics Headphones B235 User Manual
Polaroid Digital Camera HD Professional Action Camera User Manual
Polycom Telephone IP 600 User Manual
Poulan Trimmer 545154719 User Manual
ProForm Home Gym PFB48031 User Manual