Contents
7.1ch Home Theater System
Others...........................................93
HT-S6200
AV Receiver (HT-R670)
Speaker Package (HTP-670)
Front Speakers (SKF-670)
Center Speaker (SKC-670)
Surround Speakers (SKR-670)
Surround Back Speakers (SKB-670)
Powered Subwoofer (SKW-770)
Dock for iPod (UP-A1)
Instruction Manual
Thank you for purchasing an Onkyo 7.1ch Home
Theater System. Please read this manual thoroughly
before making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new 7.1ch Home Theater Sys-
tem.
Please retain this manual for future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal
without the permission of the copyright holder.
For U.S. models
FCC Information for User
CAUTION:
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild
detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive
cloths, thinners, alcohol, or other chemical solvents,
because they may damage the finish or remove the
panel lettering.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING
SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
For North American model
Pressing the [ON/STANDBY] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
For Canadian Models
5. Preventing Hearing Loss
Caution
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine, fire or
the like.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
8. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Precautions
Package Contents
Make sure you have the following items:
Placement
• The subwoofer cabinet is made out of wood and is
therefore sensitive to extreme temperatures and
humidity, do not put it in locations subject to direct
sunlight or in humid places, such as near an air condi-
tioner, humidifier, bathroom, or kitchen.
AV receiver HT-R670
• Do not put water or other liquids close to the speakers.
If liquid is spilled over the speakers, the drive units
may be damaged.
• Speakers should only be placed on sturdy, flat surfaces
that are free from vibration. Putting them on uneven or
unstable surfaces, where they may fall and cause dam-
age, will affect the sound quality.
HT-R670
• Subwoofer is designed to be used in the upright verti-
cal position only. Do not use it in the horizontal or
tilted position.
• If the unit is used near a turntable, CD player or DVD/
BD player, howling or slipping of sound may occur.
To prevent this, move the unit away from the turntable,
CD player or DVD/BD player, otherwise lower the
unit’s output level.
Remote controller and two batteries (AA/R6)
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive
devices and as such are likely to suffer discoloration or
picture distortion when conventional speakers are placed
nearby. In such situations, try moving the speakers away
from your TV or monitor. If discoloration should occur,
turn off your TV or monitor, wait 15 to 30 minutes, and
then turn it back on again. This normally activates the
degaussing function, which neutralizes the magnetic
field, thereby removing any discoloration effects. Note
that discoloration can also be caused by a magnet or
demagnetizing tool that’s too close to your TV or moni-
tor.
Speaker setup microphone
Indoor FM antenna
Input Signal Warning
AM loop antenna
The speakers can handle the specified input power when
used for normal music reproduction. If any of the
following signals are fed to them, even if the input power
is within the specified rating, excessive current may flow
in the speaker coils, causing burning or wire breakage:
1. Interstation noise from an untuned FM radio.
2. Sound from fast-forwarding a cassette tape.
3. High-pitched sounds generated by an oscillator,
electronic musical instrument, and so on.
*
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the
same regardless of color.
4. Amplifier oscillation.
5. Special test tones from audio test CDs and so on.
6. Thumps and clicks caused by connecting or discon-
necting audio cables (always turn off your amplifier
before connecting or disconnecting cables).
7. Microphone feedback.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents—Continued
Speaker Package HTP-670
Front speakers
(SKF-670)
28 rubber stoppers
*
Center speaker
(SKC-670)
Power-plug adapter (SKW-770)
Only supplied in certain countries. Use this adapter if
your AC outlet does not match with the plug on the AV
receiver’s power cord (adapter varies from country to
country).
Surround speakers
(SKR-670)
*How to mount the AC plug:
Surround back
speakers
(SKB-670)
Powered Subwoofer
(SKW-770)
Dock for iPod UP-A1
(Red)
(White)
(Green)
Speaker cable for front speakers and center speaker
Front speakers 11 ft (3.5 m)
Center speaker 10 ft (3.0 m)
*
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the
same regardless of color.
(Blue)
(Gray)
(Brown)
(Tan)
Speaker cables for surround and surround back
speakers 26 ft (8 m)
RCA cable for subwoofer connection 10 ft (3 m)
4 floor pads for the subwoofer
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Front, Center, Surround, Surround Back speakers
Remote Controller ...................................................16
Installing the Batteries .........................................16
Aiming the Remote Controller..............................16
About the UP-A1 series Dock ..............................57
Compatible iPod/iPhone models..........................57
Using the Listening Modes
Connection
Speaker Setup .....................................................68
Audio Adjust.........................................................71
Using the Audio Settings......................................73
Connecting Both Audio & Video ..........................26
Connecting Components with HDMI....................27
Connecting a VCR or DVR for Recording............32
Connecting a Camcorder,
Connecting a Cassette, CDR,
Controlling a TV ...................................................86
Controlling a DVD Player, or DVD Recorder .......87
Controlling a VCR or PVR....................................88
Controlling an RI Dock.........................................91
Controlling a Cassette Recorder..........................92
MiniDisc, or DAT Recorder ...............................36
Connecting an RI Dock........................................37
Turning On & First Time Setup
HDMI Input Setup ................................................41
Component Video Input Setup.............................42
Digital Input Setup ...............................................43
Speaker Settings .................................................44
Changing the Input Display..................................45
Audyssey 2EQ™ Room Correction and
Others
Troubleshooting.......................................................93
Specifications...........................................................97
*
To reset the AV receiver to its factory defaults, turn it on and,
while holding down the [VCR/DVR] button, press the [ON/
STANDBY] button (see page 93).
Speaker Setup ..................................................46
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Miscellaneous
AV Receiver HT-R670
• 40 AM/FM Presets
*6
Amplifier
• Audyssey Dynamic EQ™ for Loudness Correction
*6
• Audyssey 2EQ™ to Correct Room Acoustic
• 130 Watts/Channel @ 6 ohms
Problems
• 160 Watts/Channel @ 6 ohms (JEITA)
• WRAT-Wide Range Amplifier Technology
• High-Current Low-Impedance Drive
• Optimum Gain Volume Circuitry
• H.C.P.S. (High Current Power Supply) Massive High
Power Transformer
*6
• Audyssey Dynamic Volume to Maintain Optimal
Listening Level and Dynamic Range
• Crossover Adjustment
(40/50/60/70/80/90/100/120/150/200 Hz)
• A/V Sync Control Function (up to 100 ms in 10 ms
Steps)
• Theater Dimensional Virtual Surround Function
• Compatible with RI Dock for iPod
*7
Processing
*
*1
*2
• Dolby TrueHD and DTS -HD Master Audio
Decoding
• Dolby Pro Logic IIz (with “Front High” Direction
• Preprogrammed u-Compatible Remote
*1
Speaker Package HTP-670
Mode)
SKF-670 L/R 2-Way Front Speakers
• 4" (10 cm) cone woofer
• 1" (2.5 cm) Balanced dome tweeter
• Max. input power:130 W
• Pure Audio Mode (Asian models)
• Direct Mode
• Music Optimizer for Compressed Music
*3
• CinemaFILTER
• Gloss Finished
• Non-Scaling Configuration
• 6-ohm impedance
• Color-coded speaker terminals and speaker cable
• A-Form Listening Mode Memory
• 192 kHz/24-bit D/A Converters
• Powerful and Highly Accurate 32-bit DSP Processing
SKC-670 2-Way Center Speaker
• 4" (10 cm) cone woofer
Connections
• 1" (2.5 cm) Balanced dome tweeter
• Max. input power:130 W
• Gloss Finished
• 6-ohm impedance
• Color-coded speaker terminals and speaker cable
*4
• 4 HDMI Inputs and 1 Output (ver.1.3a to Support
Deep Color, x.v. Color*, Lip Sync, DTS-HD Master
Audio, DTS-HD High Resolution Audio, Dolby
TrueHD, Dolby Digital Plus, DSD and Multichannel
PCM)
SKR-670 L/R Full-Range Surround Speakers
• Onkyo
for System Control
SKB-670 L/R Full-Range Surround Back Speakers
• 3-1/4" (8 cm) Full-Range Speaker
• Max. input power:130 W
• HDTV-Ready Component Video Switching
(2 Inputs/1 Output)
• Front “Portable” Input for iPod* and MP3 Players
• Universal Port for the Dock for the iPod* /
HD Radio™ Dock (North American models)
• Gloss Finished
• 6-ohm impedance
• Color-coded speaker terminals and speaker cable
*5
• 4 Digital Inputs (2 Optical/2 Coaxial)
• Color-Coded Banana Plug Speaker Posts
• Powered Zone 2 and Zone 2 Line Out
• Subwoofer Pre Out
SKW-770 Bass Reflex Powered Subwoofer
• 10" (25 cm) cone
• Output Level Control
• Max. power:290 W
• Bi-Amp Capability for Music and Movie Sound
Effects
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Features—Continued
Dock for iPod UP-A1
• Easily links all iPhone, iPod Touch (1G, 2G), iPod
Classic, iPod (4G, 5G), iPod nano (1G, 2G, 3G, 4G),
iPod mini with Onkyo A/V Systems
*1
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
*2.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;
7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS is a registered
trademark and the DTS logos, Symbol, DTS-HD and DTS-HD
Master Audio are trademarks of DTS, Inc.
©1996-2008 DTS, Inc. All Rights Reserved.
*3 Music Optimizer™ is a trademark of Onkyo Corporation.
*4
HDMI, the HDMI logo and High Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC.
*5 HD Radio™ and the HD Radio Ready logo are proprietary
trademarks of iBiquity Digital Corporation.
To receive HD Radio broadcasts, you must install an Onkyo
UP-HT1 HD Radio tuner module (sold separately).
*6.
Manufactured under license from Audyssey Laboratories. U.S.
and foreign patents pending. Audyssey 2EQ™,
Audyssey Dynamic Volume™ and Audyssey Dynamic EQ™
are trademarks of Audyssey Laboratories.
*7
Theater-Dimensional is a trademark of Onkyo Corporation.
*
iPod is trademark of Apple Inc., registered in the U.S. and other
countries.
*
*
iPhone is trademark of Apple Inc.
“Made for iPod” means that an electronic accessory has been
designed to connect specifically to iPod and has been certified
by the developer to meet Apple performance standards.
“Works with iPhone” means that an electronic accessory has
been designed to connect specifically to iPhone and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
“x.v.Color” is a trademark of Sony Corporation.
*
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Multiroom Capability
You can use two speaker systems with this AV receiver—a surround-sound speaker system (up to 7.1 channels) in
your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it. And, you can select a
different audio source for each room.
Main Room: In your main listening room, you can enjoy up to 7.1-channel playback (see page 18).
You can enjoy the various listening modes such as Dolby and DTS (see pages 61–67).
* While Powered Zone 2 is being used, playback is reduced to 5.1-channels (see page 80).
Zone 2: In your Zone 2 room, you can enjoy 2-channel stereo playback (see page 80).
* The listening modes cannot be used with Zone 2.
Main Room
Front high left and right
speakers (Optional)
Surround back left and right
speakers
Front left and
right speakers
*
*
When you connect the front high left and
right speakers, preparate it separately.
*
While Powered Zone 2 is
being used, nothing is output
by these speakers
While Powered Zone 2 is being used,
nothing is output by these speakers
(page 81).
(page 81).
*
Front high and surround
back speakers produce no
sound at the same time.
*
Front high and surround back speakers
produce no sound at the same time.
Center speaker
Subwoofer
Surround left and right speakers
Zone 2 Room
Left and right
stereo speakers
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels
Front Panel
North American models
a b c d e
f g hijklmn o p
q
r s
u
v
w
Asian models
t
The actual front panel has various logos printed on it. They are not shown here for clarity.
The page numbers in parentheses show where you can find the main explanation for each item.
[–] & [+] buttons (50, 83)
Used to adjust the tone (bass and treble) and the
a ON/STANDBY button (40)
level of Zone 2.
b STANDBY indicator (40)
TONE button (50)
Used to select either bass or treble.
Lights up when the AV receiver is on Standby and
flashes while a signal is being received from the
remote controller.
e Remote-control sensor (16)
Receives control signals from the remote controller.
c ZONE 2 indicator (82)
Flashes when Zone 2 is being set. Lights up when
Zone 2 is on.
f Display
See “Display” on page 11.
d ZONE 2 LEVEL/TONE LEVEL buttons
ZONE 2 and OFF buttons (82)
The [ZONE 2] button is used to turn on the output
of Zone 2.
g MOVIE/TV button (61)
Selects the listening modes intended for use with
movies and TV.
h MUSIC button (61)
Selects the listening modes intended for use with
music.
The [OFF] button is used to turn off the output of
Zone 2.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels—Continued
For detailed information, see the pages in parentheses.
i GAME button (61)
q MASTER VOLUME control (49)
Sets the volume of the AV receiver to Min, 1
through 79, or Max.
Selects the listening modes intended for use with
video games.
j DIMMER button (51)
r PHONES jack (51)
Adjusts the display brightness.
This 1/4-inch phone jack is for connecting a
standard pair of stereo headphones for private
listening.
k MEMORY button (56)
Used when storing or deleting radio presets.
s MUSIC OPTIMIZER button (52)
(North American models)
l TUNING MODE button (54)
Selects the Auto or Manual tuning mode for AM
and FM radio.
Turns the Music Optimizer on or off.
t PURE AUDIO button and indicator (61)
(Asian models)
m DISPLAY button (50)
Displays various information about the currently
selected input source.
Selects the Pure Audio listening mode. The
indicator lights up when this mode is selected.
Pressing this button again selects the previous
listening mode.
n SETUP button
Opens and closes the setup menus.
buttons
u Input selector buttons (49)
Select the following input sources: DVD/BD,
VCR/DVR, CBL/SAT, AUX, TV/TAPE, TUNER,
CD, PORT.
When AM or FM is selected, the TUNING [q]/[w]
buttons are used for radio tuning, and the PRESET
[e]/[r] buttons are used to select radio presets (see
pages 54, 56). With the setup menus, they work as
arrow buttons and are used to select and set items.
The [ENTER] button is also used with the setup
menus.
v AUX INPUT (34, 60)
on. There are input jacks for composite video and
analog audio.
PORTABLE (34):
Used to connect a portable Audio Player.
p RETURN button
Selects the previously displayed setup menu.
w SETUP MIC (46)
The Audyssey 2EQ™ Room Correction and
Speaker Setup microphone connects here.
Display
a b
c
d
e
f
g
For detailed information, see the pages in parentheses.
TUNED (54):
a SLEEP indicator (51)
Lights up when tuned to a radio station.
Lights up when the Sleep function has been set.
e Message area
b MUTING indicator (51)
Displays various information.
Flashes while the AV receiver is muted.
f Audio input indicators
c Listening mode and format indicators (61)
Show the selected listening mode and audio input
signal format.
Indicate the type of audio input that’s selected as the
audio source: PCM, MULTI CH, or HDMI.
g Audyssey indicator (47, 70)
d Tuning indicators (54)
Flashes during Audyssey 2EQ™ Room Correction
and Speaker Setup. Lights up when the “Equalizer
Settings” is set to “Audyssey”.
FM STEREO (54):
Lights up when tuned to a stereo FM station.
AUTO (54):
Lights up when Auto Tuning mode is selected for
AM or FM radio. Goes off when Manual Tuning
mode is selected.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels—Continued
Rear Panel
a b
c d e
f
g h
i
j
k l
m n o
p
q
r
a DIGITAL IN COAXIAL 1 and 2
e HDMI IN 1–4 and OUT
HDMI (High Definition Multimedia Interface)
connections carry digital audio and digital video.
with an HDMI output, such as a DVD/BD player,
DVD/BD recorder, or DVR (digital video recorder).
They’re assignable, which means you can assign
each one to an input selector to suit your setup. See
“HDMI Input Setup” on page 41.
connecting components with a coaxial digital audio
output, such as a CD player or DVD/BD player.
They’re assignable, which means you can assign
each one to an input selector to suit your setup. See
“Digital Input Setup” on page 43.
b DIGITAL IN OPTICAL 1 and 2
components with an optical digital audio output,
such as a CD player or DVD/BD player. They’re
assignable, which means you can assign each one to
an input selector to suit your setup. See “Digital
Input Setup” on page 43.
The HDMI outputs are for connecting a TV or
projector with an HDMI input.
f AM and FM ANTENNA
The AM push terminals are for connecting an AM
antenna. The FM jack is for connecting an FM
antenna.
c COMPONENT VIDEO IN 1 and 2
These RCA component video inputs are for
output, such as a DVD/BD player, DVD/BD
recorder, or DVR (digital video recorder). They’re
assignable, which means you can assign each one to
an input selector to suit your setup. See
g MONITOR OUT
The composite video jack should be connected to a
video input on your TV or projector.
h UNIVERSAL PORT
This jack is for connecting the component with the
Universal Port connector such as UP-A1 series
Dock.
“Component Video Input Setup” on page 42.
d COMPONENT VIDEO OUT
This RCA component video output is for
connecting a TV or projector with a component
video input.
i FRONT L/R, CENTER, SURR L/R, and SURR
BACK L/R SPEAKERS
These terminal posts are for connecting the front
L/R, center, surround L/R, and surround back L/R
speakers.
The FRONT L/R and SURR BACK L/R terminal
posts can be used with front speakers and surround
Speakers. See “Bi-amping the Front Speakers” on
page 22.
The SURR BACK L/R terminals can be used to
connect the front high L/R speakers. See “Speaker
Settings” on page 44.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels—Continued
j u REMOTE CONTROL
This u (Remote Interactive) jack can be
connected to the u jack on another u-capable
Onkyo component for remote and system control.
To use u, you must make an analog audio
connection (RCA) between the AV receiver and the
other component, even if they are connected
digitally.
k CD IN
This analog audio input is for connecting a CD
player’s analog audio output.
l TV/TAPE IN/OUT
These analog audio input and output jacks are for
connecting a recorder with an analog audio input
and output, such as a cassette deck, MD recorder,
etc.
m CBL/SAT IN
A cable or satellite receiver can be connected here.
There is composite video input jack for connecting
the video signal, and there are analog audio input
jacks for connecting the audio signal.
n VCR/DVR IN/OUT
A video component, such as a VCR or DVR, can be
connected here for recording and playback. There is
composite video input and output jack for
connecting the video signal, and there are analog
audio input jacks for connecting the audio signal.
o DVD/BD IN
This input is for connecting a DVD/BD player.
There is composite video input jack for connecting
the video signal.
p ZONE 2 LINE OUT L/R
These analog audio outputs can be connected to the
line inputs on amplifiers in Zone 2.
q SUBWOOFER PRE OUT
This analog audio output can be connected to a
powered subwoofer.
r FRONT HIGH L/R speakers
L/R speakers.
The FRONT HIGH L/R terminal can be used with
front high speakers respectively, or used to connect
the speakers in Zone 2.
See “Connecting Zone 2” on page 80.
See pages 19–39 for hookup information.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Package
Subwoofer (SKW-770)
For detailed information, see the pages in parentheses.
■ Front
a STANDBY/ON indicator
Red:
Blue:
Subwoofer in standby mode
Subwoofer on
With the Auto Standby function, the SKW-770
automatically turns on when an input signal is
detected in Standby mode. When there’s no input
signal for a while, the SKW-770 automatically
enters Standby mode.
b POWER switch (Asian models)
Press this switch to the ON position to turn on the
power. Press it to the OFF position to turn off the
power.
c OUTPUT LEVEL control (49)
This control is used to adjust the volume of the
subwoofer.
a
■ Rear
d LINE INPUT (20)
This RCA input should be connected to the
subwoofer pre out on the AV receiver with supplied
RCA cable.
POWER
ON
SKW-770
Note:
b
Asian models
The Auto Standby function turns the subwoofer on when
the input signal exceeds a certain level. If the Auto
Standby function does not work reliably, try slightly
increasing or decreasing the subwoofer output level on
the AV receiver (page 70).
OFF
c
d
To AC outlet
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Package—Continued
Front, Center, Surround, Surround Back speakers
(SKF-670, SKC-670, SKR-670, SKB-670)
■ Rear
SKF-670
SKR-670/SKB-670
SKC-670
a
b
a
b
a
a
a Keyhole slots
These keyhole slots can be used to wall-mount the
speaker. See page 21 for mounting instructions.
b Speaker terminals
These push terminals are for connecting the speaker
to the HT-R670 with the supplied speaker cables.
The supplied speaker cables are color-coded for
easy identification. Simply connect each cable to
the same-colored positive speaker terminal.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
Installing the Batteries
Aiming the Remote Controller
When using the remote controller, point it toward the AV
receiver’s remote control sensor, as shown below.
To open the battery compartment, press
the small lever and remove the cover.
1
Remote control sensor
AV receiver
30°
30°
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
2
Approx. 16 ft.
(5 m)
Notes:
• The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct
sunlight or inverter-type fluorescent lights. Keep this
in mind when installing.
• If another remote controller of the same type is used in
the same room, or the AV receiver is installed close to
equipment that uses infrared rays, the remote
controller may not work reliably.
• Don’t put anything on top of the remote controller,
such as a book or magazine, because a button may be
pressed continuously, thereby draining the batteries.
• The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
Replace the cover and push it shut.
3
• The remote controller will not work if there’s an
obstacle between it and the AV receiver’s remote
control sensor.
• When the remote control codes have been registered
and you want to operate another component (page 84),
or when you want to operate an Onkyo component
without u connection, point the remote controller at
the other component to use it.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as
possible to prevent damage from leakage or corrosion.
• When you want to operate an Onkyo component with
u connection or an
-compatible compo-
nent connected via HDMI (pages 86, 87), point the
remote controller at the AV receiver’s remote control
sensor.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
Controlling the AV receiver
d SETUP button
Used to change settings.
To control the AV receiver, press the [RECEIVER]
button to select Receiver mode.
e LISTENING MODE buttons (61)
You can also use the remote controller to control
your DVD/BD player, CD player, and other
components. See page 84 for more details.
Used to select the listening modes.
f DIMMER button (51)
Adjusts the display brightness.
g DISPLAY button (50)
Displays information about the current input source.
h MUTING button (51)
Mutes or unmutes the AV receiver.
g
a
b
3
i VOL [q]/[w] button (49)
Adjusts the volume of the AV receiver regardless of
the currently selected remote controller mode.
TUNER
j RETURN button
*
h
i
4
settings.
RECEIVER
k AUDIO button (73)
Used to change audio settings.
When the “AudioTVOut” setting is set to “On”
(page 78), this button is disabled.
c
d
1
l SLEEP button (51)
Used with the Sleep function.
j
k
■ Controlling the tuner
To control the AV receiver’s tuner, press the [TUNER]
(or [RECEIVER]) button.
You can select AM or FM by pressing the [TUNER]
button repeatedly.
e
f
1 Arrow [q]/[w] buttons
Used to tune into radio stations.
5
2 D.TUN button (55)
Selects the Direct tuning mode.
l
2
3 DISPLAY button (55)
preset number, and so on.
4 CH +/– button (56)
Selects radio presets.
5 Number buttons (55)
tuning mode. Also you can select a preset directly.
For detailed information, see the pages in parentheses.
*
To control component, you must first enter remote
control code.
For details on entering a remote control code for a
different component, see page 84.
a ON/STANDBY button (40)
Sets the AV receiver to On or Standby.
b REMOTE MODE/INPUT SELECTOR buttons
(49, 58, 86–92)
Note:
Selects the remote controller modes and the input
sources.
An Onkyo cassette recorder connected via u can also
be controlled in Receiver mode (see page 92).
c Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to select and adjust settings.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
About Home Theater
Enjoying Home Theater
Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your
own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring Dolby Digital or DTS.
With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.
Front left and right speakers
These output the overall sound. Their role in a home theater is to provide a solid
anchor for the sound image. They should be positioned facing the listener at about
ear level, and equidistant from the TV. Angle them inward so as to create a triangle,
with the listener at the apex.
Front high left and right speakers (Optional)
These speakers are necessary to enjoy Dolby Pro Logic IIz Height,
etc. They enhance significantly the spatial experience.
Surround back left and right
speakers
Position them at least 3.3 ft (100 cm) above the front left and right
These speakers are necessary to
speakers (and as high as possible). Although it is acceptable to
enjoy Dolby Digital EX, DTS-ES
place left and right at an angle slightly wider than the front left and
Matrix, DTS-ES Discrete, etc. They
right speakers. Ideally they should be positioned directly above the
enhance the realism of surround
front left and right speakers. Front high and surround back
sound and improve sound
speakers produce no sound at the same time. When you connect
localization behind the listener.
the front high left and right speakers, preparate it separately.
Position them behind the listener
about 2–3 ft (60–100 cm) above ear
level.
Center speaker
Front high and surround back
This speaker enhances the
speakers produce no sound at the
front left and right speakers,
making sound movements
same time.
distinct and providing a full
sound image. In movies it’s
used mainly for dialog.
Position it close to your TV
facing forward at about ear
level, or at the same height as
the front left and right speakers.
Subwoofer
The subwoofer handles the bass
sounds of the LFE (Low-Frequency
Effects) channel. The volume and
quality of the bass output from your
subwoofer will depend on its position,
the shape of your listening room, and
your listening position. In general, a
good bass sound can be obtained by
installing the subwoofer in a front corner,
or at one-third the width of the wall, as
shown.
Tip: To find the best position for your
subwoofer, while playing a movie or
some music with good bass, experiment
by placing your subwoofer at various
positions within the room, and choose
the one that provides the most satisfying
results.
Surround left and right speakers
These speakers are used for precise sound positioning and
to add realistic ambience.
Position them at the sides of the listener, or slightly behind,
about 2–3 ft (60–100 cm) above ear level. Ideally they
should be equidistant from the listener.
Corner
position
1/3 of wall
position
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver
Speaker Connection Precautions
Connecting Your Speakers
Read the following before connecting your speakers:
• North American models: You can connect speakers
with an impedance of between 6 and 16 ohms. If you
use speakers with a lower impedance, and use the
amplifier at high volume levels for a long period of
time, the built-in amp protection circuit may be
activated.
impedance of between 4 and 16 ohms. If the
impedance of any of the connected speakers is 4 ohms
or more, but less than 6 ohms, be sure to set the
minimum speaker impedance to “4 ohms” (see
page 44). If you use speakers with a lower impedance,
and use the amplifier at high volume levels for a long
period of time, the built-in amp protection circuit may
be activated.
Speaker Configuration
For 7.1-channel surround-sound playback, you need
seven speakers and a powered subwoofer.
The following table shows which channels you should
use based on the number of speakers you have.
Number of speakers:
Front left
2
3
4
5
6
7
7
8
9
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Front right
Center
Surround left
✓
✓
Surround right
Surround back*1
Surround back left
Surround back right
Front high left
Front high right
✓
✓
✓
✓
✓
✓
• Disconnect the power cord from the wall outlet before
making any connections.
✓
✓
✓
✓
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. Connect
positive (+) terminals to only positive (+) terminals,
and negative (–) terminals to only negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
• Unnecessarily long or very thin speaker cables may
affect the sound quality and should be avoided.
*1 If you’re using only one surround back speaker, connect it to the
power amplifier’s left terminals.
No matter how many speakers you use, a powered
subwoofer is recommended for a powerful and solid
bass.
To get the best from your surround-sound system, you
must set the speaker settings. You can do this
automatically (see page 46) or manually (see page 68).
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
Notes:
• Front high and surround back speakers produce no
sound at the same time.
• When you connect the front high left and right
speakers, preparate it separately.
• Don’t connect more than one
cable to each speaker
terminal. Doing so may
damage the AV receiver.
• Don’t connect a speaker to several terminals.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Push terminals
Connecting the Speaker Cables
Terminal posts
Strip 3/8"-1/2"
3/8"-1/2" (10-12 mm)
1
(10-12 mm) of insulation
from the ends of the
speaker cables, and twist
the bare wires tightly, as
shown.
Strip 1/2"-5/8" (12-
15 mm) of insulation
from the ends of the
speaker cables. (Supplied
speaker cables are already
stripped.)
1/2"-5/8" (12-15 mm)
1
2
While pressing the lever, insert
the wire into the hole, and then
release the lever.
Make sure that the terminals are
gripping the bare wires, not the
insulation.
2
Unscrew the terminal. Fully insert the bare wire,
making sure that it’s touching the threaded shaft
in the center. Screw the terminal tight.
The following illustration shows which speaker should be connected to each pair of terminals for up to 7.1-channel
playback.
If you’re using only one surround back speaker, connect it to the power amplifier’s left terminals.
Blue
Surround
back left
speaker
Surround
back right
speaker
Surround
left
speaker
Surround
right
speaker
Brown
Gray
Tan
Green
Front high
left speaker right speaker
(Optional) (Optional)
Front high
Center
speaker
Front left
speaker
Front right
speaker
Powered
Subwoofer
White
Red
Notes:
• The speakers are configured by using the “Speaker Settings” on page 44 and “Speaker Setup” on page 68.
• When you connect the front high left and right speakers, preparate it sepalately.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Caution:
Wall Mounting
A mounting screw’s ability to support a speaker depends
on how well it’s anchored to the wall. If you have hollow
walls, screw each mounting screw into a stud. If there are
no studs, or the walls are solid, use suitable wall anchors.
Use screws with a head diameter of 5/16" (8 mm) or less
and a shank diameter of 5/32" (4 mm) or less. With
hollow walls, use a cable/pipe detector to check for any
power cables or water pipes before making any holes.
The speakers can easily be wall mounted by using the
keyhole slots.
To mount the front or surround speakers vertically, use
the keyhole slot shown to hang each speaker on a screw
that’s securely screwed into the wall.
Front speakers (SKF-670)
Surround speakers/Surround back speakers
(SKR-670/SKB-670)
Leave a gap of between 5/32"
(4 mm) and 5/16" (8 mm)
Wall
between the wall and the base
of the screw head, as shown.
(We recommend that you
consult a home installation
professional.)
5/32" – 5/16"
(4 mm) – (8 mm)
Keyhole slot for wall
mounting
Rubber
stoppers
Using the Rubber Stoppers for a
More Stable Platform
We recommend using the provided rubber stoppers to
achieve the best possible sound from your speakers. The
rubber stoppers prevent the speakers from moving,
providing a more stable platform.
To mount the center speaker horizontally, use the two
keyhole slots shown to hang each speaker on two screws
that are securely screwed into the wall.
Center speaker (SKC-670)
Rubber stoppers
Keyhole slot for wall mounting
3/8"
Bottom of the
SKF-670
(10 mm)
SKR-670
SKB-670
Rubber
stoppers
6-15/32" (164 mm)
Bottom of the
SKC-670
3-1/8"
(80 mm)
Tip:
If the center speaker is tilted, loosen the screw on the
declined side to move upward so that the speaker could
be adjusted vertically.
Using the Floor Pads for Subwoofer
If the subwoofer is placed on a hard floor (wood, vinyl,
tile, etc.) and playback is very loud, the subwoofer’s feet
may damage the flooring. To prevent this, place the
supplied pads underneath the subwoofer’s feet. The pads
also provide a stable base for the subwoofer.
Pad
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Bi-amping Speaker Hookup
Bi-amping the Front Speakers
The FRONT L/R and SURR BACK L/R terminal posts
can be used with front speakers and surround back
speakers respectively, or bi-amped to provide separate
tweeter and woofer feeds for front speakers, providing
improved bass and treble performance.
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• For bi-amping, the FRONT L/R terminal posts
connect to the front speakers’ woofer terminals. And
front speakers’ tweeter terminals.
Connect the AV receiver’s FRONT R positive (+)
1
terminal to the right speaker’s positive (+) woofer
(low) terminal. And connect the AV receiver’s
FRONT R negative (–) terminal to the right
speaker’s negative (–) woofer (low) terminal.
Connect the AV receiver’s SURR BACK R
2
positive (+) terminal to the right speaker’s positive
(+) tweeter (high) terminal. And connect the AV
receiver’s SURR BACK R negative (–) terminal
to the right speaker’s negative (–) tweeter (high)
terminal.
• Once you’ve completed the bi-amping connections
shown below and turned on the AV receiver, you must
set the “Sp Type” setting to “Bi-Amp” to enable bi-
amping (see page 44).
Connect the AV receiver’s FRONT L positive (+)
3
terminal to the left speaker’s positive (+) woofer
(low) terminal. And connect the AV receiver’s
FRONT L negative (–) terminal to the left
speaker’s negative (–) woofer (low) terminal.
Important:
• When making the bi-amping connections, be sure
to remove the jumper bars that link the speakers’
tweeter (high) and woofer (low) terminals.
• Bi-amping can only be used with speakers that support
bi-amping. Refer to your speaker manual.
Connect the AV receiver’s SURR BACK L
4
positive (+) terminal to the left speaker’s positive
(+) tweeter (high) terminal. And connect the AV
receiver’s SURR BACK L negative (–) terminal to
the left speaker’s negative (–) tweeter (high)
terminal.
FRONT SPEAKERS
L
L
Tweeter (high)
Woofer (low)
Left speaker
(Optional)
R
R
Tweeter (high)
Woofer (low)
Right speaker
(Optional)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available
outdoor FM antenna instead (see page 24).
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The AV receiver won’t pick up any radio signals without
any antenna connected, so you must connect the antenna
to use the tuner.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
AM ANTENNA push terminals
1
FM ANTENNA jack
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
Connecting the Indoor FM Antenna
2
The supplied indoor FM antenna is for indoor use only.
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around.)
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Attach the FM antenna, as shown.
1
■ North American models
Insert the plug fully
into the jack.
Push
Insert wire
Release
■ Asian models
Insert the plug fully
into the jack.
Once your AV receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from
your AV receiver, TV, speaker cables, and power
cords.
Once your AV receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
Use thumbtacks or something similar to
fix the FM antenna into position.
2
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a
commercially available outdoor AM antenna (see
page 24).
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available
outdoor FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from
possible noise sources, such as neon signs, busy roads,
etc.
Outdoor AM antennas work best when installed
horizontally outside, but good results can sometimes be
obtained indoors by mounting horizontally above a
window. Note that the AM loop antenna should be left
connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock
hazards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If
circumstances demand it, use a TV/FM antenna splitter,
as shown.
TV/FM antenna splitter
To AV receiver
To TV (or VCR)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
AV Connection Color Coding
About AV Connections
RCA-type AV connections are usually color coded: red,
white, and yellow. Use red plugs to connect right-
channel audio inputs and outputs (typically labeled “R”).
Use white plugs to connect left-channel audio inputs and
outputs (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
• Before making any AV connections, read the manuals
supplied with your other AV components.
• Don’t connect the power cord until you’ve completed
and double-checked all AV connections.
Optical Digital Jacks
Analog audio
Left (white)
Right (red)
Left (white)
Right (red)
The AV receiver’s optical digital jacks have shutter-type
covers that open when an optical plug is inserted and
close when it’s removed. Push plugs in all the way.
Composite video
(Yellow)
(Yellow)
Right!
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
• Push plugs in all the way to make
good connections (loose
connections can cause noise or
malfunctions).
• To prevent interference, keep
audio and video cables away from
power cords and speaker cables.
Wrong!
AV Cables and Jacks
Video / Audio
Cable
Jack
Description
HDMI connections can carry uncompressed
standard- or high-definition digital video and audio
and offer the best picture and sound quality.
HDMI
HDMI
Video
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the best
picture quality. (Some TV manufacturers label their
component video jacks slightly differently.)
Y
Y
PB/CB
PR/CR
Y
Component
video cable
PB/CB
PR/CR
C
B/PB
C
R/PR
Composite video is commonly used on TVs, VCRs,
and other video equipment.
Composite
video cable
V
Audio
This offers the best sound quality and allows you to
enjoy Dolby Digital and DTS. The audio quality is
the same as for coaxial.
OPTICAL
Optical digital
audio cable
This offers the best sound quality and allows you to
enjoy Dolby Digital and DTS. The audio quality is
the same as for optical.
Coaxialdigital
audio cable
COAXIAL
This cable carries analog audio. It’s the most
common connection format for analog audio and
can be found on virtually all AV components.
L
Analog audio
cable (RCA)
R
This cable carries analog audio.
Stereo mini
plug cable
Note: The AV receiver does not support SCART connections.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting Both Audio & Video
By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you
can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver.
: Signal Flow
Video
Video
Audio
Audio
TV, projector,
etc.
DVD player, etc.
Speakers (see page 20 for hookup details)
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your other components. Use the following sections as a guide.
Video Signal Flow Chart
Video Connection Formats
DVD player, etc.
Video equipment can be connected to the AV
receiver by using any one of the following
video connection formats: composite video,
component video, or HDMI, the latter offering
the best picture quality.
When choosing a connection format, bear in
mind that the AV receiver doesn’t convert
between formats, so only outputs of the same
format as the input will output the signal.
Composite
Component
HDMI
IN
AV receiver
MONITOR OUT
Composite
Component
HDMI
TV, projector, etc.
Audio Signal Flow Chart
DVD player, etc.
Audio Connection Formats
Audio equipment can be connected to the AV
receiver by using any of the following audio
HDMI.
Analog
Optical
Coaxial
HDMI
IN
When you connect audio equipment to an
HDMI, OPTICAL, or COAXIAL input, you
must assign that input to an input selector (see
pages 41 and 43).
AV receiver
OUT
Analog
HDMI
*1 Depends on the “AudioTVOut” setting (see page 78)
and Digital Input Setup (see page 43).
And, the audio signal can be output only when the input
video signal is from HDMI IN.
Do not connect the optical or coaxial audio cable when
you want to output the analog audio signal.
TV, projector, etc.
If signals are present at more than one input, the inputs will be selected automatically in the following order of priority:
HDMI, digital, analog.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting Components with HDMI
About HDMI
Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital
interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now,
several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can
carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital
audio, or multichannel PCM).
*1
The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface) , so TVs and displays
with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and
displays, resulting in no picture.)
The AV receiver uses HDCP (High-bandwidth Digital Content Protection), so only HDCP-compatible components will
display a picture.
The AV receiver’s HDMI interface is based on the following standard:
Deep Color, x.v. Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD,
Dolby Digital Plus, DSD and Multichannel PCM
Supported Audio Formats
• 2-channel linear PCM (16/20/24 bit/32–192 kHz)
• Multichannel linear PCM (7.1 ch, 32–192 kHz)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio)
Your DVD player must be able to output these formats from its HDMI OUT.
■ Onkyo
, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo
components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over
HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, opera-
tion with components other than
-compatible components cannot be guaranteed.
• Set “HDMI Ctrl” to “On” (page 79).
• See “Controlling a TV” (page 86) and “Controlling a DVD Player, or DVD Recorder” (page 87) for operation.
Note:
Do not connect the
-compatible component more than the following number to the HDMI input terminal so
that the linked operations work properly.
• DVD/BD player is up to three.
• DVD/BD recorder is up to three.
• Cable/Satellite Set-top box is up to four.
Do not connect the AV receiver to the other AV receiver /AV amplifier via HDMI.
When the
-compatible component more than the above-mentioned is connected, the linked operations are not
guaranteed.
About Copyright Protection
*2
The AV receiver supports HDCP (High-bandwidth Digital Content Protection) , a copy-protection system for digital
video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.
*3
*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG in 1999.
*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to
protect video content and requires a HDCP-compatible device to display the encrypted video.
*3 DDWG (Digital Display Working Group): Led by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open
industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance PCs and
digital displays.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Making HDMI Connections
Step 1:
Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD/BD player, TV,
projector, and so on.
Step 2:
Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 41).
■ Video Signals
Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.
■ Audio Signals
Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV
receiver. Normally, they are not output by the HDMI OUT, unless the “AudioTVOut” setting is set to “On” (see
page 78).
To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the “AudioTVOut”
setting to “On” (see page 78), and set your DVD player’s HDMI audio output setting to PCM.
Hint!
HDMI
OUT
HDMI
IN
TV
DVD/BD player
HDMI
ASSIGNABLE
Notes:
• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can
be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need
to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In
addition, video signals from a PC are not supported.
• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be
seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV
power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound
may be cut off.
• When the “AudioTVOut” setting is set to “On” (see page 78), or “TV Ctrl” is set to “On” (see page 79) and you’re
listening through your TV’s speakers, if you turn up the AV receiver volume control, the sound will be output by the
AV receiver’s speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s
settings, or turn down the AV receiver’s volume.
• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the
picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected
component’s instruction manual for details.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a TV or Projector
Step 1: Video Connection
Choose a video connection that matches your TV ( or ), and then make the connection.
A
B
Step 2: Audio Connection
Choose an audio connection that matches your TV (
,
, or ), and then make the connection.
a
b
c
• With connection , you can listen to and record audio from your TV or listen in Zone 2.
a
• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or
b
c
a
b
a
and .)
c
Connection
AV receiver
COMPONENT VIDEO OUT
MONITOR OUT V
Signal flow
TV
⇒
⇒
⇐
⇐
⇐
Component video input
Composite video input
Analog audio L/R output
Digital coaxial output
Digital optical output
A
B
a
TV/TAPE IN L/R
DIGITAL IN COAXIAL 2 (CBL/SAT)
DIGITAL IN OPTICAL 1 (TV/TAPE)
b
c
c
B
b
a
A
L
R
OPTICAL
OUT
COAXIAL
OUT
Y
P
B
P
R
AUDIO
OUT
VIDEO
IN
COMPONENT VIDEO IN
Connect one or the other
TV, projector,
etc.
Connection must be assigned
b
(see page 43)
If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver
Hint!
to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see pages 31 and
33).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a DVD/BD Player
Step 1: Video Connection
Choose a video connection that matches your DVD/BD player ( or ), and then make the connection.
A
B
You must connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your DVD/BD player (
,
, or ), and then make the connection.
a
b
c
• With connection , you can listen to and record audio from a DVD or listen in Zone 2.
a
• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or
b
c
a
b
a
and .)
c
• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the main
left and right outputs for connection
.
a
Connection
AV receiver
COMPONENT VIDEO IN 1 (DVD/BD)
DVD/BD IN V
Signal flow
DVD/BD player
⇐
⇐
⇐
⇐
⇐
Component video output
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
A
B
a
DVD/BD IN L/R
DIGITAL IN COAXIAL 1 (DVD/BD)
DIGITAL IN OPTICAL 1 (TV/TAPE)
b
c
c
B
b
a
A
L
R
OPTICAL
OUT
COAXIAL
OUT
Y
P
B
P
R
AUDIO
OUT
VIDEO
OUT
COMPONENT VIDEO OUT
Connect one or the other
Connection must be
assigned (see page 43)
c
DVD/BD player
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a VCR or DVR for Playback
With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV
receiver, useful if your TV has no audio outputs.
Hint!
Step 1: Video Connection
Choose a video connection that matches your VCR or DVR ( or ), and then make the connection. You must
A
B
connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your VCR or DVR (
,
, or ), and then make the connection.
a
b
c
• With connection , you can listen to the VCR or DVR even in Zone 2.
a
• To enjoy Dolby Digital and DTS, use connection or . (To listen in Zone 2 as well, use and , or and .)
b
c
a
b
a
c
Connection
AV receiver
Signal flow
VCR or DVR
COMPONENT VIDEO IN 1 (DVD/BD)
VCR/DVR IN V
⇐
⇐
⇐
⇐
⇐
Component video output
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
A
B
a
VCR/DVR IN L/R
DIGITAL IN COAXIAL 1 (DVD/BD)
DIGITAL IN OPTICAL 1 (TV/TAPE)
b
c
c
b
B
a
A
Connection
must be
A
assigned
(see page 42)
L
R
OPTICAL
OUT
COAXIAL
OUT
Y
PB
PR
AUDIO
OUT
VIDEO
OUT
COMPONENT VIDEO OUT
Connect one or the other
Connection must be
,
b
c
assigned (see page 43)
VCR, DVR
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a VCR or DVR for Recording
Step 1: Video Connection
Make the video connection
.
A
The video source to be recorded must be connected to the AV receiver via the same type of connection.
Step 2: Audio Connection
Make the audio connection
.
a
Connection
AV receiver
Signal flow
VCR or DVR
Composite video input
Audio L/R input
VCR/DVR OUT V
VCR/DVR OUT L/R
⇒
⇒
A
a
A
a
L
R
AUDIO
IN
VIDEO
IN
VCR, DVR
Notes:
• The AV receiver must be turned on for recording. Recording is not possible while it’s on Standby.
• If you want to record directly from your TV or another video source without going through the AV receiver, connect
the audio and video outputs from your TV or other video component directly to the recording VCR/DVR’s audio and
video inputs. See the manuals supplied with your TV or VCR/DVR for details.
• Video signals connected to composite video inputs can only be recorded via composite video outputs. If your
TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs
via the AV receiver, which is useful if your TV has no audio outputs.
Hint!
Step 1: Video Connection
Choose a video connection that matches the video source ( or ), and then make the connection.
A
B
You must connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches the video source (
,
, or ), and then make the connection.
a
b
c
• With connection , you can listen to and record audio from the video source or listen in Zone 2.
a
• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or
b
c
a
b
a
and .)
c
Connection
AV receiver
Signal flow
Video source
COMPONENT VIDEO IN 2 (CBL/SAT)
CBL/SAT IN V
⇐
⇐
⇐
⇐
⇐
Component video output
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
A
B
a
CBL/SAT IN L/R
DIGITAL IN COAXIAL 2 (CBL/SAT)
DIGITAL IN OPTICAL 1 (TV/TAPE)
b
c
c
B
b
a
A
L
R
OPTICAL
OUT
COAXIAL
OUT
Y
P
B
P
R
AUDIO
OUT
VIDEO
OUT
COMPONENT VIDEO OUT
Connect one or the other
Connection must be
c
assigned (see page 43)
Satellite, cable, set-top box, etc.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a Camcorder, Game Console, or Other Device
Step 1: Make the video connection
Step 2: Make the audio connection
.
.
A
a
a
AUX INPUT
L
AUDIO
R
L
AUDIO
OUT
R
Camcorder,
game console,
etc.
A
AUX INPUT
VIDEO
VIDEO OUT
Connection
AV receiver
Signal flow
Camcorder or console
Composite video output
Analog audio L/R output
AUX INPUT VIDEO
⇐
⇐
A
a
AUX INPUT L-AUDIO-R
Connecting a Portable Audio player
Step 1: Make the audio connection
.
a
Portable
Audio Player
AUX INPUT
PORTABLE
AUDIO LINE OUT
a
Connection
a
AV receiver
AUX INPUT PORTABLE
Signal flow
Portable Audio Player
⇐
Analog audio Line output
Note:
When it is connected at the same time as AUX INPUT AUDIO L/R terminal, the input of PORTABLE is given priority
to and outputted.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a CD Player or Turntable
■ CD Player or Turntable (MM) with Built-in Phono Preamp
Step 1:
Choose a connection that matches your CD player (
,
, or ).
a
b
c
Use connection for a turntable with a built-in phono preamp.
a
L
R
c
AUDIO
OUTPUT
Connect one
or the other
b
a
Connection
must be
assigned
b
a
(see page 43)
L
R
Turntable (MM) with
built-in phono preamp
COAXIAL
OUT
OPTICAL
OUT
AUDIO
OUT
CD player
• With connection , you can listen to and record audio from the CD player or listen in Zone 2.
a
• To connect the CD player digitally, use connection or . (To record or listen in Zone 2 as well, use and , or
b
c
a
b
and .)
a
c
Connection
AV receiver
CD IN L/R
Signal flow
CD or turntable
⇐
⇐
⇐
Analog audio L/R output
Digital coaxial output
Digital optical output
a
b
c
DIGITAL IN COAXIAL 2 (CBL/SAT)
DIGITAL IN OPTICAL 2 (CD)
■ Turntable (MM) with no Phono Preamp
■ Turntable with an MC (Moving Coil) Cartridge
An MC head amp and phono preamp are necessary to
connect a turntable with an MC (Moving Coil) cartridge.
Built-in
A phono preamp is necessary to connect a turntable that
doesn’t have a phono preamp built-in.
AUDIO
INPUT
AUDIO
AUDIO
OUTPUT
OUTPUT
IN
L
L
AUDIO
L
L
OUTPUT
IN
Phono preamp
R
R
L
L
R
R
Phono
preamp
CD
R
R
CD
MC head amp or
MC transformer
AUDIO
OUTPUT
AUDIO
INPUT
AUDIO
OUTPUT
AUDIO
INPUT
L
L
L
L
R
R
R
R
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
Step 1:
Choose a connection that matches your recorder (
,
, or ), and then make the connection.
a
b
c
a
a
c
b
Connect one or the other
These connections must be
assigned (see page 43)
L
R
L
R
OPTICAL
OUT
COAXIAL
OUT
AUDIO
IN
AUDIO
OUT
Cassette, CDR, MD, etc.
• With connection , you can play and record or listen in Zone 2.
a
• To connect the recorder digitally for playback, use connections and , or and
.
a
b
a
c
Connection
a
AV receiver
Signal flow
Cassette, CDR, MD, or DAT recorder
TV/TAPE IN L/R
TV/TAPE OUT L/R
⇐
⇒
Analog audio L/R output
Analog audio L/R input
DIGITAL IN COAXIAL 2 (CBL/SAT)
DIGITAL IN OPTICAL 1 (TV/TAPE)
⇐
⇐
Digital coaxial output
Digital optical output
b
c
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting an RI Dock
■ If Your iPod or iPhone Don’t Support Video:
Connect your RI Dock’s audio output jacks to the
AV receiver’s TV/TAPE IN L/R jacks.
Not all iPod models output video.
For information about which iPod models are
supported by the RI Dock, see the RI Dock’s
instruction manual.
IN
L
■ If Your iPod or iPhone Supports Video:
Connect your RI Dock’s audio output jacks to the
AV receiver’s CBL/SAT IN or VCR/DVR IN L/R
jacks, and connect its video output jack to the AV
receiver’s CBL/SAT IN or VCR/DVR IN V jacks.
R
TV/TAPE
CBL/SAT
VCR/DVR
V
V
IN
IN
IN
IN
L
L
R
R
CBL/SAT
VCR/DVR
Connect one
or the other
Notes:
• Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (see
page 85).
• Connect the RI Dock to the AV receiver with an u cable (see page 39).
• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.
• Set the AV receiver’s Input Display to “DOCK” (see page 45).
• See the RI Dock’s instruction manual for more information.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting a Dock with the Universal Port connector
Notes:
• While your iPod or iPhone is seated in the Dock, its battery will be charged when the AV receiver is set to On or
Standby.
• When UP-A1 series Dock that seated iPod or iPhone is connected, the power consumption on standby mode slightly
increases.
• Make a connection with the MONITOR OUT V when you watch videos on the TV (see page 29).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AV receiver—Continued
Connecting Onkyo u Components
Step 1: Make sure that each Onkyo component is connected to the AV receiver with an analog audio cable (RCA).
Step 2: Make the necessary u connections (see illustration below).
Step 3: If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 45).
With u (Remote Interactive), you can use the following special functions:
■ Auto Power On/Standby
When you start playback on a component connected via u, if the AV receiver is on Standby, it will automatically
turn on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all
components connected via u will also go on Standby.
■ Direct Change
When playback is started on a component connected via u, the AV receiver automatically selects that component
as the input source.
■ Remote Control
You can use the AV receiver’s remote controller to control your other u-capable Onkyo components. You must
enter the appropriate remote control code first (see page 85). And remember to point the remote controller at the AV
receiver and not the other component.
Notes:
IN
• Use only u cables for u connections. u cables
L
are supplied with Onkyo players (DVD, CD, etc.).
R
• Some components have two u jacks. You can
CD
connect either one to the AV receiver. The other jack
is for connecting additional u-capable
components.
• Connect only Onkyo components to u jacks.
Connecting other manufacturer’s components may
cause a malfunction.
e.g., CD player
• Some components may not support all u functions.
R
L
Refer to the manuals supplied with your other Onkyo
components.
ANALOG
AUDIO OUT
e.g., DVD player
• While Zone 2 is on, the Auto Power On/Standby and
Direct Change u functions do not work.
R
L
ANALOG
AUDIO OUT
Connecting the Power Cord
• Before connecting the power cord, connect all your speakers and AV components.
• Plug the end of the power cord into a suitable wall outlet.
• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On the AV receiver
ON/STANDBY
ON/STANDBY
RECEIVER
STANDBY indicator
Turning On and Standby
Remote
controller
On the AV receiver, press the [ON/STANDBY] button.
AV receiver
On the remote controller, press the [RECEIVER] button, followed by the
[ON/STANDBY] button.
The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
or
To turn the AV receiver off, press the [ON/STANDBY] button, or press the remote
controller’s [ON/STANDBY] button. The AV receiver will enter Standby mode. To
prevent any loud surprises the next time you turn on the AV receiver, turn down the
volume before you turn it off.
Up and Running in a Few Easy Steps
To get your system up and running with the minimum of fuss, here’s a few pointers to help you configure the AV
receiver before you use it for the very first time. These settings only need to be made once.
■ Do the 2EQ Room Correction and Speaker Setup—this is
essential!
Y
■ Did you connect a component to an HDMI input,
component video input, or digital audio input?
If you did, see “HDMI Input Setup” on page 41, “Component Video
respectively.
HDMI
COAXIAL
OPTICAL
PB
PR
■ Did you connect a UP-A1 series Dock?
If you did, see “Connecting a Dock with the Universal Port
connector” on page 38.
UP-A1 series Dock
40
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup
This section explains the settings that you need to make before using the AV receiver for the very first time.
HDMI Input Setup
Use the Up and Down [q]/[w]
3
buttons to select “1-1. HDMI”,
and then press [ENTER].
If you connect a video component to an HDMI IN, you
must assign that input to an input selector. For example,
if you connect your DVD player to HDMI IN1, you must
assign HDMI IN1 to the DVD/BD input selector.
Input selector
DVD/BD
VCR/DVR
CBL/SAT
AUX
Default assignment
HDMI1
HDMI2
HDMI3
- - - - -
Use the Up and Down [q]/[w]
buttons to select an input
selector, and use the Left and
Right [e]/[r] buttons to select:
HDMI1: Select if the video
component is connected to
HDMI IN 1.
4
TV/TAPE
CD
- - - - -
- - - - -
PORT
- - - - -
HDMI2: Select if the video
component is connected to
HDMI IN 2.
HDMI3: Select if the video
component is connected to
HDMI IN 3.
HDMI4: Select if the video
component is connected to
HDMI IN 4.
RECEIVER
qwer
ENTER
SETUP
- - - - -: Select if you’re not using the
HDMI OUT.
Press the [SETUP] button.
Setup closes.
5
Press the [RECEIVER] button,
followed by the [SETUP] button.
1
2
Notes:
input selector.
• When an HDMI IN is assigned to an input selector as
explained here, the digital audio input for that input
selector is automatically set to the same HDMI IN.
See “Digital Input Setup” on page 43.
• If you connect an input component (such as UP-A1
series Dock that seated iPod or iPhone) to the
UNIVERSAL PORT jack, you cannot assign any
input to PORT selector.
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
Use the Up and Down [q]/[w]
buttons to select “1. Input
Assign”, and then press
[ENTER].
• Do not assign the component connected with the
HDMI input to the TV/TAPE selector when you set
“TV Ctrl” setting to “On” (see page 79). Otherwise,
appropriate CEC (Consumer Electronics Control)
operation is not guaranteed.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Component Video Input Setup
Use the Up and Down [q]/[w]
buttons to select
3
4
If you connect a video component to a COMPONENT
VIDEO IN, you must assign that input to an input
selector. For example, if you connect your DVD player
to COMPONENT VIDEO IN 2, you must assign
COMPONENT VIDEO IN 2 to the DVD/BD input
selector.
“1-2. Component”, and then
press [ENTER].
Input selector
DVD/BD
VCR/DVR
CBL/SAT
AUX
Default assignment
IN1
- - - - -
IN2
Use the Up and Down [q]/[w]
buttons to select an input
selector, and use the Left and
Right [e]/[r] buttons to select:
IN1: Select if the video component
is connected to
- - - - -
- - - - -
- - - - -
- - - - -
TV/TAPE
CD
PORT
COMPONENT VIDEO IN 1.
IN2: Select if the video component
is connected to
COMPONENT VIDEO IN 2.
- - - - -: Select if you’re not using the
COMPONENT VIDEO
RECEIVER
OUT.
Press the [SETUP] button.
Setup closes.
5
qwer
ENTER
SETUP
Notes:
• If you connect an input component (such as UP-A1
series Dock that seated iPod or iPhone) to the
UNIVERSAL PORT jack, you cannot assign any
input to PORT selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
Press the [RECEIVER] button,
followed by the [SETUP] button.
1
2
Use the Up and Down [q]/[w]
buttons to select “1. Input
Assign”, and then press
[ENTER].
42
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Digital Input Setup
Use the Up and Down [q]/[w]
buttons to select “1-3. Digital”,
and then press [ENTER].
3
4
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example,
if you connect your CD player to OPTICAL IN 1, you
must assign OPTICAL IN 1 to the CD input selector.
These are the default assignments.
Input selector
DVD/BD
VCR/DVR
CBL/SAT
AUX
Default assignment
COAX1
- - - - -
Use the Up and Down [
q
]/[
w
]
COAX2
- - - - -
buttons to select an input selector,
and then use the Left and Right
TV/TAPE
CD
OPT1
[
e
]/[
r
] buttons to select:
COAX1:Select if the component is
connected to DIGITAL IN
COAXIAL 1.
OPT2
PORT
- - - - -
COAX2:Select if the component is
connected to DIGITAL IN
COAXIAL 2.
OPT1: Select if the component is
connected to DIGITAL IN
OPTICAL 1.
RECEIVER
OPT2: Select if the component is
connected to DIGITAL IN
OPTICAL 2.
- - - - -: Select if the component is
connected to an analog input.
qwer
ENTER
SETUP
Notes:
• Press the [ENTER] button when you
do not use the signal of audio from
*
displayed like “COAX1 ”.
*
Press the [RECEIVER] button,
followed by the [SETUP] button.
• For the input selector that you want to
listen the analog audio, set to “- - - - -”
in the Digital Audio Input setting and
HDMI Input setting (see page 41).
1
2
Press the [SETUP] button.
Setup closes.
5
Use the Up and Down [q]/[w]
buttons to select “1. Input
Assign”, and then press
[ENTER].
Notes:
• When an HDMI IN is assigned to an input selector in
“HDMI Input Setup” on page 41, this input
assignment is automatically set to the same HDMI IN.
And in addition to the usual inputs (e.g., COAX1,
COAX2, etc.), you can also select HDMI inputs.
• If you connect an input component (such as UP-A1
series Dock that seated iPod or iPhone) to the
UNIVERSAL PORT jack, you cannot assign any input
to PORT selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Speaker Settings
(Asian models) Use the Up and
Down [q]/[w] buttons to select
“Impedance”, and use the Left
and Right [e]/[r] buttons to
select:
4
5
6
If you change these settings, you must run the
Audyssey 2EQ™ Room Correction and Speaker Setup
again (see page 46).
4 ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Speaker Impedance to 4 ohms.
6 ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
North American models do not support speakers with
an impedance of less than 6 ohms.
To use bi-amping, you must change the Speaker Type
setting. For hookup information, see page 22.
Notes:
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the
volume.
Use the Up and Down [q]/[w]
buttons to select “Sp Type”, and
use the Left and Right [e]/[r]
buttons to select:
Normal: Select this if you’ve
connectedyourfrontspeakers
normally.
Press the [RECEIVER] button,
followed by the [SETUP] button.
1
Bi-Amp:Select this if you’ve
connectedyourfrontspeakers
for bi-amped operation.
Note:
Powered Zone2 cannot be used if “Sp
Type” is set to “Bi-Amp”.
Use the Up and Down [q]/[w]
2
Use the Up and Down [q]/[w] but-
tons to select “SB/FH”, and then
use the Left and Right [e]/[r]
buttons to select:
buttons to select “2. Speaker
Setup”, and then press [ENTER].
FrontHigh:
Select this if you’ve con-
nected your front high speak-
ers to the SURR BACK L/R
terminal posts.
SurrBack:
Select this if you’ve con-
nected your surround back
L/R terminal posts.
Use the Up and Down [q]/[w]
3
buttons to select “2-1. Sp
Settings”, and then press
[ENTER].
Note:
If the “Sp Type” setting is set to “Bi-
Amp”, or Powered Zone 2 is set to “Not
Act” (page 81), this setting cannot be
selected.
Press the [SETUP] button.
Setup closes.
7
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Changing the Input Display
If you connect an u-capable Onkyo RI Dock to the
TV/TAPE IN, CBL/SAT IN or VCR/DVR IN jacks, for
u to work properly, you must change this setting.
This setting can only be changed on the AV receiver.
VCR/DVR CBL/SAT TV/TAPE
Press the [TV/TAPE], [CBL/SAT]
1
or [VCR/DVR] input selector
button so that “TV/TAPE”,
“CBL/SAT” or “VCR/DVR”
appears on the display.
or
or
Press and hold down the
2
[TV/TAPE], [CBL/SAT] or
[VCR/DVR] input selector button
(about 3 seconds) to change the
setting.
Repeat this step to select DOCK.
For the TV/TAPE input selector, the
or
setting changes in this order:
TV/TAPE → MD → CDR
→
DOCK
For the CBL/SAT input selector, the
or
For the VCR/DVR input selector, the
setting changes in this order:
VCR/DVR ↔ DOCK
See “Controlling Other Components”
on pages 90, 91
Note:
DOCK can be selected for the TV/TAPE, CBL/SAT or
VCR/DVR input selector, but not at the same time.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Measurement Positions
Audyssey 2EQ™ Room Correction
and Speaker Setup
To create a listening environment in which several
people can enjoy your home theater simultaneously,
Audyssey 2EQ takes measurements at three positions
within the listening area.
With the supplied calibrated microphone,
Audyssey 2EQ automatically determines the number of
speakers connected, their size for purposes of bass
management, optimum crossover frequencies to the
subwoofer (if present), and distances from the primary
listening position. Audyssey 2EQ then removes the
distortion caused by room acoustics by capturing room
frequency and time domain. The result is clear, well-
balanced sound for everyone. Enabling Audyssey 2EQ
allows you to also use Audyssey Dynamic EQ™, which
maintains the proper octave-to-octave balance at any
volume level (see page 72).
a First measurement point
Also referred to as the Main Listening Position this
refers to the most central position where one would
normally sit within the listening environment. 2EQ
uses the measurements from this position to
calculate speaker distance, level, polarity, and the
optimum crossover value for the subwoofer.
b Second measurement point
The right side of the listening area.
c Third measurement point
Before using this function, connect and position all of
your speakers.
If Audyssey Dynamic EQ is set to “On”,
The left side of the listening area.
The distances between points a and b and points a
and c must be at least 1 meter.
From the examples below, choose the listening area that
best matches yours and place the microphone
accordingly when prompted.
Audyssey Dynamic Volume™ becomes available.
About Audyssey Dynamic EQ
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased by
taking into account human perception and room
acoustics. Dynamic EQ selects the correct frequency
response and surround levels moment-by-moment at
any user-selected volume setting. The result is bass
response, tonal balance, and surround impression that
remain constant despite changes in volume. Dynamic
EQ combines information from incoming source
levels with actual output sound levels in the room, a
prerequisite for delivering a loudness correction
solution. Audyssey Dynamic EQ works in tandem
with Audyssey 2EQ to provide well-balanced sound
for every listener at any volume level.
TV
TV
TV
TV
TV
TV
TV
TV
TV
About Audyssey Dynamic Volume
Audyssey Dynamic Volume solves the problem of
large variations in volume level between television
programs, commercials, and between the soft and loud
passages of movies. Dynamic Volume looks at the
preferred volume setting by the user and then monitors
how the volume of program material is being
perceived by listeners in real time to decide whether an
adjustment is needed. Whenever necessary, Dynamic
Volume makes the necessary rapid or gradual
adjustments to maintain the desired playback volume
level while optimizing the dynamic range.
:
:
Listening area
Listening position
Audyssey Dynamic EQ is integrated into Dynamic
Volume so that as the playback volume is adjusted
automatically, the perceived bass response, tonal
balance, surround impression, and dialog clarity
remain the same whether watching movies, flipping
between television channels, or changing from stereo
to surround sound content.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Notes:
Using Audyssey 2EQ™
• Before starting Audyssey 2EQ™ Room Correction
and Speaker Setup, arrange the room and connect the
speakers as you would for enjoying movies. Changes
to the room after auto setup requires you run the auto
setup again, as room EQ characteristics may have
changed.
• When starting the room correction and speaker setup,
do not stand between the speakers and microphone,
and avoid obstacles blocking the path between
speakers and microphone. This will produce
inaccurate results.
• Position the microphone at ear height of a seated
listener with the microphone tip pointed directly at the
ceiling using a tripod. Do not hold the microphone in
your hand during measurements as this will produce
innacurate results.
Notes:
• (Asian models) If any of your speakers is 4 ohms,
change the Speaker Impedance setting before
running the Audyssey 2EQ Room Correction and
speaker setup (see page 44).
• If the AV receiver is muted, it will be unmuted
automatically when the Audyssey 2EQ Room
Correction and Speaker Setup starts.
• Room correction and speaker setup cannot be
performed while a pair of headphones is connected.
• It takes about 10 minutes to complete the room
correction and speaker setup for three positions.
Total measurement time varies depending on the
number of speakers.
• Do not connect or disconnect any speakers during
room correction and speaker setup.
• Make the room as quiet as possible. Background noise
can disrupt the room measurements. Close windows,
silence cell phones, televisions, radios, air
conditioners, fluorescent lights, home appliances,
light dimmers, or other devices.
ON/STANDBY
• Cell phones should be turned off or placed away from
all audio electronics during the measurement process
as Radio Frequency Interference (RFI) may cause
measurement disruptions (even if the cell phone is not
in use).
Speaker setup microphone
SETUP MIC
Press [ENTER].
The room calibration and speaker setup starts.
3
Test tones are played through each speaker as
Audyssey 2EQ Room Correction and Speaker
Setup runs. This process takes a few minutes.
Please refrain from talking during measure-
ments and do not stand between speakers and
the microphone.
ENTER
Turn on the AV receiver.
Note:
1
You can cancel the Room Correction and
Speaker Setup at any point in this procedure
simply by disconnecting the setup microphone.
Set the speaker setup
microphone at the Main Listening
2
Position
a
(page 46), and
When the following display appears,
4
connect it to the SETUP MIC jack.
move the speaker setup microphone to
measurement point b (page 46), and
then press [ENTER].
Audyssey indicator
The speaker setting menu appears.
If you change these settings, refer to
steps 5–6 on “Speaker Settings”
(page 44) or step 5 on “Setting the
Powered Zone 2” (page 81).
Audyssey 2EQ performs more measurements.
This takes a few minutes.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
• The right surround back speaker has been detected but
the left surround back speaker hasn’t.
When the following display appears,
5
move the speaker setup microphone to
measurement point c (page 46), and
then press [ENTER].
❏ Write Error
This message appears if saving fails.
❏ Mismatch Error
™
Audyssey 2EQ performs more
measurements.
This takes a few minutes.
When the measurements are complete, the
results are calculated and saved automatically.
This message appears if a speaker that was detected
during the 1st measurement is not detected during the
2nd or 3rd measurements. If this message appears, check
your speaker connections, and then try again.
To Retry the Room Correction and
Speaker Setup
When the room correction and speaker
setup is complete, disconnect the
speaker setup microphone.
6
Press the [ENTER] button.
Make sure speakers that cannot be
detected are connected properly.
Notes:
Changing the Speaker Settings Manually
• When the room correction and speaker setup is
complete, the Equalizer Settings (page 70) will be set
to “Audyssey” and the “Dynamic EQ” (page 72) will
be set to “On”.
• You can cancel the Room Correction and Speaker
Setup at any point in this procedure simply by
disconnecting the setup microphone.
If you wish to make changes to the settings found during
the automatic speaker setup, follow the directions on
pages 68–70.
Using a Powered Subwoofer
low-frequency sound and its position is usually low
down, it may not be detected by the Audyssey 2EQ
Room Correction and Speaker Setup. When
“Subwoofer” is set to “No” in the “2-2.Sp Config
(Speaker Configuration)” (page 68), increase the
subwoofer’s volume, select its highest crossover
frequency, and then try running the Audyssey 2EQ
Room Correction and Speaker Setup again. Note that if
the volume is set too high and the sound distorts, it may
not be detected, so use an appropriate volume level.
Error Messages
While the room correction and speaker setup is in
progress, one of the following error messages may
appear:
❏ Ambient noise is too high
This message appears if there’s too much background
noise and the measurements cannot be performed
properly. Remove the source of the noise and try again.
❏ Speaker Detect Errors
This message appears if one of the speaker-related errors
below occurs.
• One of the front speakers has not been detected.
• One of the surround speakers has not been detected.
• The surround back speakers have been detected but
the surround speakers haven’t.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Basic AV receiver Operation
Subwoofer’s
rear panel
INPUT
SELECTOR
MASTER VOLUME
RECEIVER
OUTPUT
LEVEL
control
VOL q, w
MAX
OUTPUT LEVEL
MIN
Input selector
Use the AV receiver’s input selector buttons to select an input source.
1
To select an input source with the remote controller, press its
[RECEIVER] button, and then use its INPUT SELECTOR buttons.
Remote
controller
AV receiver
Start playback on the source component.
To watch a BD, DVD, or other video source, on your TV, select the video input that’s
connected to the AV receiver’s COMPONENT VIDEO OUT, HDMI OUT, or
MONITOR OUT.
On some DVD players, you may need to change the digital or HDMI audio output
settings.
2
3
To adjust the volume, use the MASTER VOLUME control or the remote
controller’s VOL [q]/[w] button.
Remote
controller
AV receiver
Since the AV receiver is designed for home theaters, it has a wide volume range for
precise adjustment. The volume can be set to Min, 1 through 79, or Max.
To set the level of the subwoofer, use the OUTPUT LEVEL control.
Because our ears are less sensitive to very low bass sounds, there’s a temptation to set
the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to
what you think is the optimal level, and then back it off slightly.
MASTER VOLUME
Select a listening mode and enjoy!
See “Using the Listening Modes” on page 61.
4
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations—Continued
This section explains functions that can be used with any
input source.
■ Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
■ Treble
DISPLAY
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
Press
[RECEIVER]
first
MUTING
Displaying Source Information
You can display various information about the current
input source as follows.
Press the [RECEIVER] button,
and then press the [DISPLAY]
button repeatedly to cycle
through the available
information.
Note:
This procedure can also be performed on the AV receiver
by using its [DISPLAY] button.
DIMMER
SLEEP
The following information can typically be displayed:
Input source &
volume*1
Signal format*2
or sampling
frequency
MUSIC OPTIMIZER DIMMER DISPLAY
Input source &
listening mode
*1 When AM or FM radio is used, the band, preset number, and
frequency are displayed.
*2 If the input signal is analog, or AM or FM radio is selected, no
format information is displayed. If the input signal is PCM, the
sampling frequency is displayed. If the input signal is digital but
not PCM, the signal format is displayed. Information is
displayed for about 3 seconds, then the previous display
reappears.
PHONES TONE [–]/[+]
Adjusting the Bass & Treble
You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio listening mode is
selected.
AV receiver
Press the [TONE] button
repeatedly to select either
“Bass” or “Treble”.
Use the TONE [–]/[+] buttons to
adjust.
Tip:
This procedure can also be performed
on the remote controller by using
[AUDIO] button (see page 73).
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations—Continued
Setting the Display Brightness
Using the Sleep Timer
You can adjust the brightness of the display.
With the sleep timer, you can set the AV receiver so that
it turns off automatically after a specified period.
Press the [RECEIVER] button,
and then press the remote
Remote
controller
Press the [RECEIVER] button,
and then press the remote
controller’s [SLEEP] button
repeatedly to select the required
sleep time.
controller’s [DIMMER] button
repeatedly to select: dim,
dimmer, or normal brightness.
You can also use the AV receiver’s
[DIMMER] button.
You can set the sleep time from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set, as shown. The specified sleep time
appears on the display for about 5
seconds, then the previous display
reappears.
AV receiver
SLEEP indicator
Muting the AV receiver
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
To check the remaining sleep time, press the [SLEEP]
button. Note that if you press the [SLEEP] button while
the sleep time is being displayed, you’ll shorten the sleep
time by 10 minutes.
You can temporarily mute the output of the AV receiver.
Press the [RECEIVER] button,
and then press the remote
controller’s [MUTING] button.
The output is muted and the MUTING
indicator flashes on the display.
Using Headphones
For private listening, you can connect a pair of stereo
headphones (1/4-inch phone plug) to the AV receiver’s
PHONES jack.
To unmute the AV receiver, press the remote
controller’s [MUTING] button again, or adjust the
volume. The output is unmuted and the MUTING
indicator goes off.
Muting is cancelled when the AV receiver is set to
Standby.
Notes:
• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the PHONES
jack, the speakers are turned off. (The Powered Zone 2
speakers are not turned off.)
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it was already set to Pure
Audio, Mono, Stereo, or Direct, in which case it stays
the same. (Pure Audio listening mode is not available
for North American models.)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations—Continued
Using the Music Optimizer
The Music Optimizer function enhances the sound
quality of compressed music files. Use it with music files
that use “lossy” compression, such as MP3.
RECEIVER
(North American models) To turn
the Music Optimizer “On” or
“Off”, use the AV receiver’s
[MUSIC OPTIMIZER] button .
The setting is stored individually for
each input selector.
e, r
AUDIO
On: Music Optimizer on.
Press the [RECEIVER] button,
and then press and hold [AUDIO]
button for about 8 seconds.
1
2
Tip:
This procedure can also be performed
on the remote controller by using
[AUDIO] button (see page 74).
Note:
The Music Optimizer function only works with PCM
digital audio input signals with a sampling rate below
48 kHz and analog audio input signals. The Music
Optimizer is disabled when the Direct or Pure Audio
listening mode is selected.
While “Auto” is displayed (about
3 seconds), use the Left and
Right [e]/[r] buttons to select:
PCM, DTS, or Auto.
Specifying the Digital Signal Format
PCM:
The following table shows the display indicator for each
digital signal format.
Only 2-channel PCM format input
signals will be heard. If the input
signal is not PCM, the PCM
indicator will flash and there will be
no sound.
Format
Dolby Digital
DTS
Display
DTS:
Only DTS format input signals will
be heard. If the input signal is not
DTS, the DTS indicator will flash
and there will be no sound.
PCM
PCM
Normally, the AV receiver detects the format of digital
input signals automatically. However, if you experience
either of the following issues when playing PCM or DTS
sources, you can specify the signal format manually.
• If the beginnings of tracks from a PCM source are cut
off, try the PCM setting.
Auto (default):
The format is detected
automatically. If no digital input
signal is present, the corresponding
analog input is used instead.
• If noise is produced when fast forwarding or
rewinding a DTS CD, try the DTS setting.
• The setting is stored individually for each input
selector.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio
AM/FM Frequency Step Setup
Use the Up and Down [q]/[w]
buttons to select “FM/AM” (North
American models) or “AM Freq”
(Asian models).
4
5
(North American models)
RECEIVER
(Asian models)
qwer
ENTER
SETUP
Use the Left and Right [e]/[r]
buttons to select:
(North American models)
200k/10k:
For AM/FM tuning to work properly, you must specify
the AM/FM frequency step used in your area. Note that
when this setting is changed, all radio presets are
deleted.
Select if 200 k/10 k steps are
used in your area.
50k/9k: Select if 50 k/9 k steps are
used in your area.
Press the [RECEIVER] button,
followed by the [SETUP] button.
(Asian models)
10kHz: Select if 10 kHz steps are
used in your area.
1
9kHz: Select if 9 kHz steps are used
in your area.
Press the [SETUP] button.
Setup closes.
6
Use the Up and Down [q]/[w]
2
buttons to select
“7. HardwareSetup”, and then
press [ENTER].
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Use the Up and Down [q]/[w]
3
buttons to select “7-2. Tuner”,
and then press [ENTER].
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
■ Manual Tuning Mode
Using the Tuner
With the built-in tuner, you can enjoy AM and FM radio
stations and store your favorite stations as presets for
easy selection.
Press the [TUNING MODE]
button so that the AUTO indicator
disappears from the display.
1
TUNER q TUNING w
Press and hold the TUNING Up or
Down [q]/[w] button.
2
The frequency stops changing when
you release the button.
Press the button repeatedly to change
the frequency one step at a time.
TUNING MODE
Listening to the Radio
This model changes FM/AM frequency in 200 k/10 k (or
50 k/9 k) Hz steps.
In Manual Tuning mode, FM stations will be in mono.
Use the [TUNER] input selector
button to select “AM” or “FM”.
In this example, FM has been selected.
Tuning into Weak FM Stereo Stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Band
Frequency
Note:
(Actual display depends on country.)
You can also use the remote controller’s Up and Down
[q]/[w] buttons to tune the radio.
Tuning into AM/FM Radio Stations
■ Auto Tuning Mode
Press the [TUNING MODE]
button so that the AUTO indicator
appears on the display.
1
Press the TUNING Up or Down
2
[q]/[w] button.
Searching stops when a station is
found.
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator also appears.
FM STEREO
AUTO
TUNED
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
■ Tuning into Stations by Frequency
You can tune into AM and FM stations directly by
entering the appropriate frequency.
Displaying AM/FM Radio Information
DISPLAY
TUNER
Press the [DISPLAY] button to
display the available information.
Band
Frequency
Preset #
Number
buttons
D.TUN
Listening mode
Press the [TUNER] button
1
repeatedly to select “AM” or
“FM”, followed by the [D.TUN]
button.
(Actual display depends on country.)
Within 8 seconds, use the
2
number buttons to enter the
frequency of the radio station.
For example, to tune to 87.5 (FM),
press 8, 7, 5.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Selecting Presets
Presetting AM/FM Stations
ePRESETr
MEMORY
ePRESETr
You can store a combination of up to 40 of your favorite
AM and FM radio stations.
Tune into the AM or FM station
you want to store as a preset.
1
CH +/–
Press the [MEMORY] button.
The preset number flashes.
2
While the preset number is
3
flashing (about 8 seconds), use
the PRESET [e]/[r] buttons to
select a preset from 1 through 40.
Number
buttons
Press the [MEMORY] button
4
again to store the station.
The station is stored and the preset
number stops flashing.
Repeat this procedure for all of your
favorite stations.
AV receiver
To select a preset, use the
PRESET [e]/[r] buttons or the
remote controller’s CH [+/–]
button.
Deleting Presets
MEMORY
or
Remote
controller
TUNING MODE
Select the preset that you want to
delete.
or
1
You can also use the remote
controller’s number buttons to
select a preset directly.
See the next section.
While holding down the
[MEMORY] button, press the
[TUNING MODE] button.
2
The preset is deleted and its number
disappears from the display.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
UP-A1 series Dock for iPod/iPhone
■ Adjusting the Adapter
About the UP-A1 series Dock
The adapter needs to be adjusted to match your
particular iPod or iPhone. If there’s a gap between the
back of your iPod or iPhone and the adapter, turn the
adapter counterclockwise to close the gap. Turning the
adapter counterclockwise moves it forward. Turning it
clockwise moves it backward.
With the UP-A1 series Dock, you can easily play the
music, photo, or movie stored on your Apple iPod or
iPhone through the AV receiver and enjoy great sound.
You can use the AV receiver’s remote controller to
operate your iPod or iPhone.
For the latest information on the Dock, see the Onkyo
Web site at: www.onkyo.com
Forward
Adapter
Backward
Notes:
• Make sure that the output level of the AV receiver is
set to minimum.
• To prevent damage to the dock connector, don’t twist
your iPod or iPhone when inserting or removing it,
and be careful not to knock over the dock while your
iPod or iPhone is inserted.
Dock connector
Compatible iPod/iPhone models
• Do not take off your iPod or iPhone from the Dock
when you play back the music, photo, or movie stored
on your iPod or iPhone.
• Don’t use the UP-A1 with any other iPod or iPhone
accessories, such as FM transmitters and
microphones, because they may cause a malfunction.
• It is recommended that you update your iPod or
iPhone software before using it with this unit. The
updater for the iPod or iPhone software is available at
the Apple website.
■ Made for:
• All iPhone models
• iPod touch (2nd generation)
• iPod touch (1st generation)
• iPod classic
• iPod (5th generation)
• iPod (4th generation)
• iPod nano (4th generation)
• iPod nano (3rd generation)
• iPod nano (2nd generation)
• iPod nano (1st generation)
• iPod mini
Function Overview
■ Basic Operation
Note:
Note:
The AV receiver may take several seconds to startup, so
you might not hear the first few seconds of the first song.
Before using the UP-A1 series Dock, update your iPod
or iPhone with the latest software, available from the
Apple Web site.
• Auto Power On Function
If you start iPod or iPhone playback while the AV
receiver is on Standby, the AV receiver will
automatically turn on and select your iPod or iPhone
as the input source. Then, your iPod or iPhone will
start playback.
Putting Your iPod/iPhone in the Dock
1. Turn on the AV receiver, and select the [PORT]
selector.
2. Align your iPod or iPhone with the Dock
connector, and carefully place your iPod or iPhone
in the slot, as shown.
• Direct Change Function
If you start iPod or iPhone playback while listening
to another input source, the AV receiver will
automatically select your iPod or iPhone as the input
source.
Remove case
before inserting
• Using the AV receiver’s Remote Controller
You can use the AV receiver’s remote controller to
control basic iPod or iPhone functions.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
UP-A1 series Dock for iPod/iPhone—Continued
Operating Notes:
Controlling iPod/iPhone
• Before selecting a different input source, stop iPod or
iPhone playback to prevent the AV receiver from
selecting the iPod or iPhone input source by mistake.
• If any accessories are connected to your iPod or
iPhone, the AV receiver may not be able to select the
input source properly.
• While your iPod or iPhone is in the UP-A1 series
Dock, its volume control has no effect. If you adjust
your iPod or iPhone models volume control while it’s
in the UP-A1 series Dock, make sure it’s not set too
high before you reconnect your headphones.
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
Dock, you can control your iPod or iPhone in the Dock
The [PORT] button is preprogrammed with the remote
control code for controlling a Dock with Universal Port
connector.
For details on entering a remote control code,
see page 84.
When Using a Dock with Universal Port connector:
• Connect the Dock to the UNIVERSAL PORT jack.
• See to the Dock’s instruction manual for more infor-
mation.
■ Using Your iPod or iPhone models Alarm
Clock
You can use your iPod or iPhone models Alarm Clock
function to automatically turn on your iPod or iPhone
and the AV receiver at a specified time. The AV
receiver’s input source will automatically be set to the
[PORT] selector.
You can control your iPod or iPhone when “PORT” is
selected as the input source.
Press [PORT] button first
Notes:
• To use this function, your iPod or iPhone must be in
the UP-A1 series Dock, and the UP-A1 series Dock
must be connected to the AV receiver.
• When you use this function, be sure to set the AV
receiver’s volume control to a suitable level.
• The AV receiver may take several seconds to startup,
so you might not hear the first few seconds of the first
song.
f
g
h
■ Charging Your iPod or iPhone models
Battery
The UP-A1 series Dock charges your iPod or iPhone
models battery while your iPod or iPhone is in the UP-
A1 series Dock and connected to the UNIVERSAL
PORT jacks on the AV receiver. While your iPod or
iPhone is seated in the UP-A1 series Dock, its battery
will be charged when the AV receiver is set to “On” or
“Standby”.
i
a
j
k
b
c
d
l
m
n
Note:
When UP-A1 series Dock that seated iPod or iPhone is
connected, the power consumption on standby mode
slightly increases.
e
o
Note:
For detailed operation of the iPod or iPhone, please refer
to the instruction manual.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
UP-A1 series Dock for iPod/iPhone—Continued
Status messages
a Arrow [q]/[w] and ENTER buttons
Used to navigate menus and select items.
❏ The AV receiver is checking the connection
b Previous [7] button
Restarts the current song. Press it twice to select the
previous song.
with the dock
c Rewind [5] button
Press and hold to rewind.
d Pause [3] button
❏ The AV receiver do not support the
Pauses playback.
connected dock
e REPEAT button
Used with the repeat function.
f MUTING button (51)
Mutes or unmutes the AV receiver.
❏ UP-A1 series Dock is connected
g ALBUM +/– button
Selects the next or previous album.
h VOL [q]/[w] button (49)
Adjusts the volume of the AV receiver.
Your iPod or iPhone is properly stationed in a UP-A1
series Dock connected to the UNIVERSAL PORT jack
of this unit, and the connection between your iPod or
iPhone and this unit is complete.
When connection is confirmed, “UP-A1” is displayed
for about 8 seconds.
i PLAYLIST [e]/[r] buttons
Selects the previous or next playlist on the iPod or
iPhone.
j RETURN button
Exits the menu or returns to the previous menu.
❏ Dock is not connected
k Play [1] button
Starts playback. If the component is off, it will turn
on automatically.
l Next [6] button
Your iPod or iPhone was removed from a UP-A1 series
Dock connected to the UNIVERSAL PORT jack of this
unit.
Selects the next song.
m Fast Forward [4] button
Press and hold to fast forward.
n Stop [2] button
Note:
Stops playback and displays a menu.
When the status message is not displayed on the AV
receiver’s display, check the connection to your iPod or
iPhone.
o RANDOM button
Used with the shuffle function.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
This section explains how to record the input source and
how to record audio and video from separate sources.
Recording from Different AV Sources
You can overdub audio onto your video recordings by
simultaneously recording audio and video from two
separate sources. This is possible because only the audio
source is switched when an audio-only input source,
such as TV/TAPE, TUNER, or CD, is selected, the video
source remains the same.
In the following example, audio from the CD player
connected to the CD IN and video from the camcorder
connected to the AUX INPUT VIDEO jack are recorded
by the VCR connected to the VCR/DVR OUT jacks.
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• Sources connected to a digital input cannot be
recorded. Only analog inputs can be recorded.
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
• While the Pure Audio listening mode is selected, the
VCR/DVR OUT V jack don’t output video signal, so
select another mode when recording.
Recording the Input Source
Audio sources can be recorded to a recorder (e.g.,
cassette deck, CDR, MD) connected to the TV/TAPE
OUT jack. Video sources can be recorded to a video
recorder (e.g., VCR, DVR) connected to the VCR/DVR
OUT jacks. See pages 25 to 39 for hookup information.
Camcorder
video signal
audio signal
Use the input selector buttons to
select the source that you want
to record.
1
AV receiver
See “Which Connections Should I
Use?” on page 26 to see which signals
can be output and recorded.
You can watch the source while
recording it. The AV receiver’s
MASTER VOLUME control has no
Remote
controller
effect on recording.
CD player
VCR
Prepare the camcorder and CD player for
playback.
1
On your recorder, start
recording.
2
Prepare the VCR for recording.
2
3
4
On the source component, start
playback.
3
Press the [AUX] input selector button.
Note:
Press the [CD] input selector button.
This selects the CD player as the audio source but
leaves the camcorder as the video source.
If you select a different input source during recording,
that input source will be recorded instead.
Start recording on the VCR, then start
playback on the camcorder and CD player.
Video from the camcorder and audio from the CD
player are recorded by the VCR.
5
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting with the Remote Controller
Selecting Listening Modes
For a description of each listening mode, see “About the
Listening Modes” on page 66.
• The Dolby Digital and DTS listening modes can
only be selected if your DVD player is
HDMI).
STEREO
MOVIE/TV
MUSIC
GAME
• The listening modes you can select depends on
the format of the input signal. To check the
format, see “Displaying Source Information”
on page 50.
• While a pair of headphones is connected, you
can only select the Pure Audio, Mono, Direct,
or Stereo listening mode.
Press the [RECEIVER] button,
and then press the LISTENING
MODE button repeatedly to
select the listening mode.
Selecting on the AV receiver
MUSIC
■ LISTENING MODE buttons
[MOVIE/TV] button
This button selects the listening modes intended for
use with movies and TV.
GAME
MOVIE/TV
PURE AUDIO
[MUSIC] button
This button selects the listening modes intended for
use with music.
■ [PURE AUDIO] button
(Asian models)
This button selects the Pure Audio listening mode.
When this mode is selected, the AV receiver’s
display is turned off and only the HDMI outputs
output video signals. Pressing this button again will
select the previous listening mode.
[GAME] button
This button selects the listening modes intended for
use with video games.
[STEREO] button
This button selects the Stereo listening mode and All
Channel Stereo listening mode.
■ LISTENING MODE buttons
[MOVIE/TV] button
This button selects the listening modes intended for
use with movies and TV.
[MUSIC] button
This button selects the listening modes intended for
use with music.
[GAME] button
This button selects the listening modes intended for
use with video games.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
Listening Modes Available for Each Source Format
The Speaker layout illustration shows which
speakers are set to active in the “Sp Config”
setting (see page 68).
Front high
L Speaker
Front high
R Speaker
FHL
FL
FHR
FR
Front R
Speaker
Front L Speaker
C
The LISTENING MODE button illustration
shows that listening modes can be selected.
Center Speaker
Subwoofer
SW
Surround R
Speaker
SL
SR
Surround L
Speaker
Surround back
R Speaker
Surround back
L Speaker
SBL
SBR
: active in the speaker settings
C
C
:
non-active in the speaker settings
Mono/Multiplex Sources
✔: Available Listening Modes
Speaker layout
FHL
FHR
FHL
FL
FHR
FHL
FHR
FR
FHL
FL
FHR
FR
FL
C
FR
C
FR
FL
C
C
Listening Mode
Button
SW
SW
SW
SW
SL
SR
SL
SR
SL
SR
SL
SR
SBL
SBR
SBL
SBR
SBL
SBR
SBL
SBR
Pure Audio*1
Direct
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Stereo
Mono
*2
Orchestra
Unplugged
Studio-Mix
TV Logic
✔
✔
✔
✔
✔
✔
✔
✔
*2
*2
*2
*2
*2
*2
*2
Game-RPG
Game-Action
Game-Rock
Game-Sports
*2
*2
AllChStereo
✔
✔
✔
✔
FullMono
✔
✔
✔
✔
T-D (Theater-
Dimensional)
✔
✔
Notes:
*1 Pure Audio listening mode is not available for North American models.
*2 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 74.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192 kHz.
• The listening modes cannot be selected with some source formats.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
Stereo Source
✔: Available Listening Modes
Speaker layout
FHL
FL
FHR
FR
FHL
FL
FHR
FHL
FHR
FR
FHL
FL
FHR
FR
C
C
FR
FL
C
C
Listening Mode
Button
SW
SW
SW
SW
SL
SR
SL
SR
SL
SR
SL
SR
SBL
SBR
SBL
SBR
SBL
SBR
SBL
SBR
Pure Audio*1
Direct
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Stereo
Mono
PLII/PLIIx
Movie*3
PLII/PLIIx
Music*3
PLII/PLIIx
Game*3
✔
✔
✔
✔
✔ (Surround Back)
✔ (Surround Back)
✔ (Surround Back)
✔
✔
✔ (Front High)
✔ (Surround Back)
✔ (Surround Back)
PLIIz Height
Neo:6 Cinema
Neo:6 Music
Orchestra
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
*2
✔
*2
Unplugged
Studio-Mix
TV Logic
✔
*2
✔
*2
✔
*2
Game-RPG
Game-Action
Game-Rock
Game-Sports
✔
*2
✔
*2
✔
*2
✔
*2
AllChStereo
FullMono
✔
✔
✔
*2
✔
✔
✔
✔
✔
T-D (Theater-
Dimensional)
✔
✔
Notes:
*1 Pure Audio listening mode is not available for North American models.
*2 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 74.
*3 If there are no surround back speakers or Powered Zone 2 is being used, Dolby Pro Logic II is used.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192 kHz.
• The listening modes cannot be selected with some source formats.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
5.1 channel Sources
✔: Available Listening Modes
Speaker layout
FHL
FL
FHR
FR
FHL
FL
FHR
FHL
FHR
FR
FHL
FL
FHR
FR
C
C
FR
FL
C
C
Listening Mode
Button
SW
SW
SW
SW
SL
SR
SL
SR
SL
SR
SL
SR
SBL
SBR
SBL
SBR
SBL
SBR
SBL
SBR
Pure Audio*1
Direct
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Stereo
Mono
DolbyDigital/
DolbyDigital
Plus/TrueHD/
Multichannel/
DTS/DTS-HD
High Resolution
Audio/DTS-HD
Master Audio/
DTS Express/
✔
✔
✔
*3
DSD
Neo:6
✔ (Surround Back)
✔ (Surround Back)
✔ (Surround Back)
✔ (Front High)
PLIIx Movie
PLIIx Music
PLIIz Height
DolbyEX
✔ (Surround Back)
*2
Orchestra
✔
✔
✔
✔
✔
✔
✔
✔
✔
*2
Unplugged
Studio-Mix
TV Logic
✔
*2
✔
*2
✔
*2
Game-RPG
Game-Action
Game-Rock
Game-Sports
✔
*2
✔
*2
✔
*2
✔
*2
AllChStereo
✔
✔
✔
*2
FullMono
✔
✔
✔
✔
✔
T-D (Theater-
Dimensional)
✔
✔
Notes:
*1 Pure Audio listening mode is not available for North American models.
*2 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 74.
*3 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound
according to the player. In that case, set the output setting on the player side to PCM.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192 kHz.
• The listening modes cannot be selected with some source formats.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
7.1 channel Sources
✔: Available Listening Modes
Speaker layout
FHL
FL
FHR
FR
FHL
FL
FHR
FHL
FHR
FR
FHL
FL
FHR
FR
C
C
FR
FL
C
C
Listening Mode
Button
SW
SW
SW
SW
SL
SR
SL
SR
SL
SR
SL
SR
SBL
SBR
SBL
SBR
SBL
SBR
SBL
SBR
*3
✔
Pure Audio*1
Direct
✔
✔
✔
✔
✔
✔
(Surround Back)
*3
✔
(Surround Back)
Stereo
Mono
✔
✔
✔
✔
✔
✔
✔
✔
Multichannel/D
olbyDigital
Plus/TrueHD/
DTS-HD High
Resolution
*3
✔
✔
✔
(Surround Back)
Audio/DTS-HD
Master Audio
PLIIz Height
Orchestra
✔ (Front High)
*2
✔
✔
✔
✔
✔
✔
✔
✔
✔
*2
Unplugged
Studio-Mix
TV Logic
✔
*2
✔
*2
✔
*2
Game-RPG
Game-Action
Game-Rock
Game-Sports
✔
*2
✔
*2
✔
*2
✔
*2
AllChStereo
FullMono
✔
✔
✔
*2
✔
✔
✔
✔
✔
T-D (Theater-
Dimensional)
✔
✔
DTS-ES Discrete/Matrix Sources
DTS-ES
Discrete
DTS-ES Matrix
✔ (Surround Back)
Notes:
*1 Pure Audio listening mode is not available for North American models.
*2 Which Front high speakers or Surround back speakers outputs the sound is switched by the “SpLayout” setting on page 74.
*3 When the input source contains the encoded front high channel, front high speakers output the sound.
• Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192 kHz.
• The listening modes cannot be selected with some source formats.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
Dolby Digital
About the Listening Modes
Use this mode with DVDs that bear the Dolby Digital
logo, and Dolby Digital TV broadcasts. This is the most
common digital surround-sound format, and it’ll put you
right in the middle of the action, just like being in a
movie theater or concert hall.
The AV receiver’s listening modes can transform your
listening room into a movie theater or concert hall, with
high fidelity and stunning surround sound.
Pure Audio
In this mode, the display and video circuitry are turned
off, minimizing possible noise sources for the ultimate in
high-fidelity reproduction. (As the video circuitry is
turned off, only video signals input through HDMI IN
can be output.)
5.1-channel source + Dolby EX
These modes expand 5.1-channel sources for 6.1/7.1-
channel playback. They’re especially suited to Dolby EX
soundtracks that include a matrix-encoded surround
back channel. The additional channel adds an extra
dimension and provides an enveloping surround sound
experience, perfect for rotating and fly-by sound effects.
Direct
In this mode, audio from the input source is output
directly with minimal processing, providing high-
fidelity reproduction. All of the source’s audio channels
are output as they are.
Dolby Digital Plus
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest
multichannel audio format from Dolby. It supports up to
7.1 channels with 48 kHz sampling rate.
Stereo
Sound is output by the front left and right speakers and
subwoofer.
Dolby TrueHD
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc
formats, this new Dolby format offers up to 7.1 discrete
channels of digital audio with 48/96 kHz, up to 5.1-
channels with 192 kHz sampling rate.
Mono
Use this mode when watching an old movie with a mono
soundtrack, or use it with the foreign language
soundtracks recorded in the left and right channels of
some movies. It can also be used with DVDs or other
sources containing multiplexed audio, such as karaoke
DVDs.
5.1-channel source + Dolby PLIIx Music
These modes use the Dolby Pro Logic IIx Music mode
to expand 5.1-channel sources for 6.1/7.1-channel
playback.
Multichannel
This mode is for use with PCM multichannel sources.
5.1-channel source + Dolby PLIIx Movie
These modes use the Dolby Pro Logic IIx Movie mode
to expand 5.1-channel sources for 7.1-channel playback.
Dolby Pro Logic IIx
Dolby Pro Logic II
Dolby Pro Logic IIx expands any 2-channel source for
7.1-channel playback. It provides a very natural and
seamless surround-sound experience that fully envelops
the listener. As well as music and movies, video games
can also benefit from the dramatic spatial effects and
vivid imaging. If you’re not using any surround back
speakers, Dolby Pro Logic II will be used instead of
Dolby Pro Logic IIx.
DTS
The DTS digital surround-sound format supports up to
5.1 discrete channels and uses less compression for high-
fidelity reproduction. Use it with DVDs and CDs that
bear the DTS logo.
DTS 96/24
This mode is for use with DTS 96/24 sources. This is
high-resolution DTS with a 96 kHz sampling rate and
24-bit resolution, providing superior fidelity. Use it with
DVDs that bear the DTS 96/24 logo.
•
Dolby PLIIx Movie
Use this mode with any stereo or Dolby Surround
(Pro Logic) movie (e.g., TV, DVD, VHS).
DTS-ES Discrete
•
Dolby PLIIx Music
This mode is for use with DTS-ES Discrete soundtracks,
which use a discrete surround back channel for true
6.1/7.1-channel playback. The seven totally separate
audio channels provide better spatial imaging and 360-
degree sound localization, perfect for sounds that pan
across the surround channels. Use it with DVDs that bear
the DTS-ES logo, especially those with a DTS-ES
Discrete soundtrack.
Use this mode with any stereo or Dolby Surround
(Pro Logic) music source (e.g., CD, radio, cassette,
TV, VHS, DVD).
•
Dolby PLIIx Game
Use this mode with video games, especially those
that bear the Dolby Pro Logic II logo.
Dolby Pro Logic IIz Height
Dolby Pro Logic IIz Height is designed to more
effectively use existing program material when height
channel speaker outputs are present. Dolby Pro Logic
IIz Height can be used to upmix a variety of sources
from movies and music, but are particularly well-suited
to upmix game content.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
DTS-ES Matrix
Onkyo Original DSP Modes
This mode is for use with DTS-ES Matrix soundtracks,
which use a matrix-encoded back-channel for 6.1/7.1-
channel playback. Use it with DVDs that bear the DTS-
ES logo, especially those with a DTS-ES Matrix
soundtrack.
Orchestra
Suitable for classical or operatic music, this mode
emphasizes the surround channels in order to widen the
stereo image, and simulates the natural reverberation of
a large hall.
DTS Neo:6
Unplugged
This mode expands any 2-channel source for up to 7.1-
channel playback. It uses seven full-bandwidth channels
of matrix decoding for matrix-encoded material,
providing a very natural and seamless surround sound
experience that fully envelops the listener.
Suitable for acoustic instruments, vocals, and jazz, this
mode emphasizes the front stereo image, giving the
impression of being right in front of the stage.
Studio-Mix
Suitable for rock or pop music, listening to music in this
mode creates a lively sound field with a powerful
acoustic image, like being at a club or rock concert.
•
Neo:6 Cinema
Use this mode with any stereo movie (e.g., TV,
DVD, VHS).
TV Logic
•
Neo:6 Music
This mode adds realistic acoustics to TV shows
produced in a TV studio, surround effects to the entire
sound, and clarity to voices.
Use this mode with any stereo music source (e.g.,
CD, radio, cassette, TV, VHS, DVD).
5.1-channel source + Neo:6
This mode uses Neo:6 to expand 5.1-channel sources for
6.1/7.1-channel playback.
Game-RPG
Use this mode when playing role playing game discs.
Game-Action
Use this mode when playing action game discs.
DTS-HD High Resolution Audio
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest
multichannel audio format from DTS. It supports up to
7.1 channels with 96 kHz sampling rate.
Game-Rock
Use this mode when playing rock game discs.
Game-Sports
DTS-HD Master Audio
Use this mode when playing sports game discs.
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc
formats, this new DTS format offers up to 7.1 discrete
channels of digital audio with 48/96 kHz, up to 5.1-
channels with 192 kHz sampling rate.
All Ch Stereo
Ideal for background music, this mode fills the entire
listening area with stereo sound from the front, surround,
and surround back speakers.
Full Mono
DTS Express
In this mode, all speakers output the same sound in
mono, so the sound you hear is the same regardless of
where you are within the listening room.
This format supports up to 5.1 channels and a lower
sampling rate of 48 kHz. Applications include
interactive audio and commentary encoding for HD
DVD Sub Audio and Blu-ray Secondary Audio. Also
broadcast and media servers.
T-D (Theater-Dimensional)
With this mode you can enjoy a virtual surround sound
even with only two or three speakers. This works by
controlling how sounds reach the listener’s left and right
ears. Good results may not be possible if there’s too
much reverb, so we recommend that you use this mode
in an environment with little or no natural reverb.
DSD
DSD stands for Direct Stream Digital and is the format
used to store digital audio on Super Audio CDs (SACD).
This mode can be used with SACDs that feature
multichannel audio.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup
Common Procedures in Setup Menu
Remote
indicator
Press the [RECEIVER] button followed by
the [SETUP] button.
1
2
Use the Up and Down [q]/[w] buttons to
select main menu, and then press
[ENTER].
RECEIVER
qwer
Use the Up and Down [q]/[w] buttons to
select the function, and then press the
[ENTER] button.
3
4
ENTER
SETUP
Use the Up and Down [q]/[w] button to
select item, and then use the Left and
Right [e]/[r] buttons to set them.
Number
Buttons
When you’ve finished, press the [SETUP]
5
button.
Setup closes.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Speaker Setup
This section explains how to check the speaker settings and how to set them manually, which is useful if you change a
Some of the speaker settings are set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function
(see page 46).
2-1. Sp Settings
See “Speaker Settings” on page 44.
2-2. Sp Config (Speaker Configuration)
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify
“FullBand” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good
sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be
output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover
frequencies.
Subwoofer
Yes: Select if a subwoofer is connected (default).
No: Select if no subwoofer is connected.
*1
FullBand, 40 Hz to 100 Hz (default), 120 Hz, 150 Hz, 200 Hz
Front
*2
FullBand, 40 Hz to 100 Hz, 120 Hz, 150 Hz, 200 Hz
None: Select if no speaker is connected.
Center
*2
Surr
*2*3*5*6
FrontH
SurrBk
*3*4*5*7
*8
1ch: Select if only one surround back L speaker is connected.
2ch: Select if two (left and right) surround back speakers are connected (default).
SurrBack ch
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
LPFofLFE
80 Hz, 90 Hz, 100 Hz (default), 120 Hz
(Low-Pass Filter for the LFE Channel)
This setting is not set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function
(see page 46).
With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
*9
DoubleBass
This setting is not set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function
(see page 46).
With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and
center to the subwoofer.
On: Double Bass function on (default).
Notes:
*2 If the “Front” setting is set to anything other than “FullBand”, “FullBand” cannot be selected here.
*3 If the “Surr” setting is set to “None”, this setting cannot be selected.
*4 If the “Surr” setting is set to anything other than “FullBand”, “FullBand” cannot be selected here.
*5 If the “Sp Type” setting is set to “Bi-Amp” (page 44), or Powered Zone 2 is being used (page 81), this setting cannot be selected.
*6 If the “SB/FH” setting is set to “SurrBack” (page 44), this setting cannot be selected.
*7 If the “SB/FH” setting is set to “FrontHigh” (page 44), this setting cannot be selected.
*8 If the “SurrBk” Setting is set to “None” (page 68), this setting cannot be selected.
*9 This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “FullBand”.
2-3. Sp Distance (Speaker Distance)
These settings are set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 46).
With these settings, you can specify the distance from each speaker to the listening position.
Measure and make a note of the distance from each speaker to the listening position.
Notes:
• Speakers that you set to “No” or “None” in the “2-2. Sp Config (Speaker Configuration)” (page 68) cannot be
selected.
• The speaker distance setting cannot be changed while a pair of headphones is connected.
• The Center, Subwoofer and Front High distances can be set up to 5 ft. (1.5 m) more or less than the Left distance.
For example, if the Left distance is set to 20 ft. (6 m), the Center, Subwoofer, Front High Left and Front High Right
distances can be set between 15 and 25 ft. (4.5 and 7.5 m).
• The Surround and Surround Back distances can be set up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the Left
distance. For example, if the Left distance is set to 20 ft. (6 m), the Surr Right, Surr Left, Surr Back R, and Surr Back
L distances can be set between 5 and 25 ft. (1.5 and 7.5 m).
Unit
feet: Distances can be set in feet. Range: 1 to 30 feet in 1-foot steps.
meters: Distances can be set in meters. Range: 0.3 to 9 meters in 0.3-meter steps.
Left, FrontH L, Center, FrontH R, Right, Surr R, SurrBk R,
SurrBk L, Surr L, Subwfr
Specify the distance from the each speaker to your listening position.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4. Level Cal (Speaker Levels Calibration)
These settings are set automatically by the Audyssey 2EQ™ Room Correction and Speaker Setup function
(see page 46).
You can set the volume level of each speaker so that all speakers can be heard equally at the listening position. A pink
noise test tone is output by the front left speaker.
Notes:
• Speakers that you set to “No” or “None” in the “2-2. Sp Config (Speaker Configuration)” (page 68) do not output
the test tone.
• The speaker levels cannot be adjusted while a pair of headphones is connected or the AV receiver is muted.
Left, FrontH L, Center, FrontH R, Right, Surr R, SurrBk R,
SurrBk L, Surr L, Subwfr
The levels can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).
2-5. Equalizer (Equalizer Settings)
These settings are set automatically by the Audyssey 2EQ Room Correction and Speaker Setup function (see page 46).
Here you can adjust the tone of individual speakers. To set the volume of individual speakers, see page 68.
Notes:
• You can select: “63Hz”, “250Hz”, “1000Hz”, “4000Hz”, or “16000Hz”. And for the subwoofer, “25Hz”, “40Hz”,
“63Hz”, “100Hz”, or “160Hz”.
• While the Direct or Pure Audio listening mode is selected, the equalizer settings have no effect.
• The equalizer setting cannot be changed while a pair of headphones is connected.
EQ
Manual: You can adjust the equalizer for each speaker manually. If you select “Manual”,
continue with this procedure.
Select a frequency
Use the Down [w] button to select “Ch”, and then use the Left and
1
Right [e]/[r] buttons to select a speaker.
Use the Up and Down [q]/[w] buttons to select a frequency. Use
2
the Left and Right [e]/[r] buttons to adjust the level at that
frequency.
The volume at each frequency can be adjusted from –6 to +6 dB in 1 dB steps.
Tip:
Low frequencies (e.g., 63 Hz) affect bass sounds; high frequencies (e.g.,
16000 Hz) affect treble sounds.
Use the Up [q] button to select “Ch”, and then use the Left and
Configuration)” (page 68) cannot be selected.
3
Right [e]/[r] buttons to select another speaker.
Repeat steps 1 and 2 for each speaker.
Audyssey: The tone for each speaker is set automatically by the Audyssey 2EQ Room
Correction and Speaker Setup function. Be sure to select this setting after having
performed the Audyssey 2EQ Room Correction and Speaker Setup. “Dynamic EQ”
and “Dyn Vol” become available (page 72).
Off: Tone off, response flat.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Audio Adjust
With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.
3. Audio Adjust
3-1. Mux/Mono (Multiplex/Mono)
Input (Mux)
Main: The main channel is output (default).
Sub: The sub channel is output.
M/S: Both the main and sub channels are output.
This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or
languages with multiplex sources, multilingual TV broadcasts, and so on.
Input (Mono)
L+R: Both the left and right channels are output (default).
L: Only the left channel is output.
R: Only the right channel is output.
This setting determines which channel is output when the Mono listening mode is used with a stereo source.
3-2. Dolby
These settings apply to only 2-channel stereo sources.
If you’re not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx.
Panorama
On: Panorama function on.
Off: Panorama function off (default).
With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music
listening mode.
Dimension
–3 to +3 (default: 0)
With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music
listening mode. Higher settings move the sound field backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve
the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move
it backward.
Center Width
0 to 7 (default: 3)
With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output by only
the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front
left and right speakers to create a phantom center.) This setting controls the front left, right, and center mix,
allowing you to adjust the weight of the center channel sound.
Dolby EX
Dolby EX
Auto: If the source signal contains a Dolby EX flag, the Dolby EX listening mode is
used.
Manual: You can select any available listening mode (default).
This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround
back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD
only.
Notes:
• If the “SurrBack” Setting is set to “None”, this setting cannot be selected (see page 68).
• If the “FrontH” setting is set to other than “None”, this setting is fixed at “Manual” (see page 68).
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
3-3. DTS
Neo:6 Music
Center Image
0 to 5 (default: 2)
The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With
this setting, you can specify by how much the front left and right channel output is attenuated in order to create
the center channel.
Setting a value [0] in the middle is set to hear a sound. Sound is spread in left and right (the outside) so that the
set value is made big. Please adjust by liking.
3-4. Audyssey
When the room correction and speaker setup is complete, the “2-5. Equalizer (Equalizer Settings)” (page 70) will
be set to “Audyssey” and the “Dynamic EQ” will be set to “On”.
Dynamic EQ
Off: Audyssey Dynamic EQ off (default).
On: Audyssey Dynamic EQ on.
With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into
account human perception and room acoustics. It does so by selecting the correct frequency response and
surround volume levels moment-by-moment so that the content sounds the way it was created at any volume
level--not just at reference level.
Dyn Vol (Dynamic Volume)
Off: Audyssey Dynamic Volume™ off.
Light: Light Compression Mode becomes active (see page 46).
Medium: Medium Compression Mode becomes active (see page 46).
Heavy: Heavy Compression Mode becomes active. This setting affects volume the most,
causing all sounds to be of equal loudness.
Note:
After the automatic speaker setting is completed, even if Equalizer Setting is set besides “Audyssey”, when
Dynamic EQ is set to “On”, Equalizer Settings is set to “Audyssey”.
When Dynamic Volume is set to effective, Equalizer Setting is set to “Audyssey” and Dynamic EQ is set to
“On”. When Dynamic EQ is set to “Off”, Dynamic Volume becomes “Off” automatically.
3-5. T-D (Theater-Dimensional)
LstnAngl (Listening Angle)
Wide: Select if the listening angle is 40 degrees (default).
Narrow: Select if the listening angle is 20 degrees.
With this setting, you can optimize the Theater- Dimensional listening
Front left
speaker
Front right
speaker
mode by specifying the angle of the front left and right speakers relative
to the listening position. Ideally, the front left and right speakers should
be equidistant from the listening position and at an angle close to one of
the two available settings.
20°/40°
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Using the Audio Settings
You can change various audio settings by pressing the [AUDIO] button.
Note:
When the “AudioTVOut” setting is set to “On” (page 78), the [AUDIO] button is disabled.
Press the [RECEIVER] button followed by
the [AUDIO] button.
1
2
3
Use the Up and Down [q]/[w] buttons to
RECEIVER
select an item.
Use the Left and Right [e]/[r] buttons to
change the setting.
qwer
Repeat this step for the other settings.
AUDIO
Tone Control Settings
You can adjust the bass and treble for the front speakers, except when the Direct or Pure Audio listening mode is
selected.
Notes:
• To bypass the bass and treble tone circuits, select the Direct or Pure Audio listening mode.
• This procedure can also be performed on the AV receiver by using its [TONE], [–], and [+] buttons.
Bass
–10 dB to +10 dB in 2 dB steps (default: 0 dB)
–10 dB to +10 dB in 2 dB steps (default: 0 dB)
Treble
Late Night Function
With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear
quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want
to disturb anyone.
Late Night
For Dolby Digital and Dolby Digital Plus sources, the options are:
Off: Late Night function off (default).
Low: Small reduction in dynamic range.
High: Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
Auto: The Late Night function is set to “On” or “Off” automatically (default).
Off: Late Night function off.
On: Late Night function on.
Notes:
• The effect of the Late Night function depends on the material that you are playing and the intention of the original
sound designer, and with some material there will be little or no effect when you select the different options.
• The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby
TrueHD.
• The Late Night function is set to Off when the AV receiver is set to Standby. For Dolby TrueHD sources, it will be
set to Auto.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
CinemaFILTER
With the CinemaFILTER, you can soften overly bright movie soundtracks, which are typically mixed for
reproduction in a movie theater.
CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Digital
Plus, TrueHD, Dolby Pro Logic IIx Movie, Dolby Pro Logic II Movie, Multichannel, DTS, DTS-ES, DTS Neo:6
Cinema, DTS 96/24, Neo:6, DTS-HD High Resolution, DTS-HD Master and DTS Express.
Cinema Fltr
Off: CinemaFILTER off (default).
On: CinemaFILTER on.
Note:
The CinemaFILTER may not work when used with certain input sources.
Audyssey Dynamic Volume™
Dyn Vol
See “Dyn Vol” of “Audio Adjust” on page 72.
Music Optimizer
The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that
use “lossy” compression, such as MP3.
M.Optimizer
Off: Music Optimizer off (default).
On: Music Optimizer on.
Note:
The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and
analog audio input signals. The Music Optimizer is disabled when the Direct or Pure Audio listening mode is selected.
Speaker Layout
You can select the priority of the use of SurrBack speakers or FrontHigh speakers.
SpLayout
SurrBk: The sound from surround back speakers is output by priority.
FrontH: The sound from front high speakers is output by priority.
Notes:
• If the “Sp Type” setting is set to “Bi-Amp” (page 44) or Powered Zone 2 is being used, this setting cannot be
selected.
• When the listening mode that doesn’t correspond to the switch of the speakers is used, the setting cannot be selected.
• This setting can also be selected on the remote controller by using [GUIDE/TOP MENU] button.
Speaker Levels
You can adjust the volume of each speaker while listening to an input source.
These temporary adjustments are cancelled when the AV receiver is set to Standby.
Subwfr (Subwoofer)
–15 dB to +12 dB (default: 0 dB)
Center
Notes:
–12 dB to +12 dB (default: 0 dB)
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to “No” or “None” in the “2-2. Sp Config (Speaker Configuration)” cannot be adjusted
(see page 68).
A/V Sync
When using progressive scanning on your DVD player, you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the audio signals.
A/V Sync
Notes:
0 ms to 100 ms in 10 ms steps
• A/V Sync is disabled when the Pure Audio listening mode is selected, or when the Direct listening mode is
used with an analog input source.
• The setting is stored individually for each input selector.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
A/PCM: With this setting, you can specify the
listening mode to be used when an analog (CD,
TV, LD, VHS, MD, turntable, radio, cassette,
cable, satellite, etc.) or PCM digital (CD, DVD,
etc.) audio signal is played.
Dolby: With this setting, you can specify the
listening mode to be used when a Dolby Digital or
Dolby Digital Plus format digital audio signal is
played (DVD, etc.).
DTS: With this setting, you can specify the
listening mode to be used when a DTS or DTS-
HD High Resolution format digital audio signal is
played (DVD, LD, CD, etc.).
Assigning Listening Modes to Input
Sources
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes
during playback, but the mode specified here will be
resumed once the AV receiver has been set to Standby.
Press the [RECEIVER] button followed by
the [SETUP] button.
1
DF2ch: Specifies the default listening mode for
2-channel (2/0) stereo sources in a digital format,
such as Dolby Digital or DTS.
Use the Up and Down [q]/[w] buttons to
2
select “5. ListeningMode”, and then press
[ENTER].
Mono: With this setting, you can specify the
listening mode to be used when a mono digital
audio signal is played (DVD, etc.).
MCH P: Specifies the default listening mode for
multichannel PCM sources input via a HDMI IN,
such as DVD-Audio.
Use the Up and Down [q]/[w] buttons to
3
select the input source that you want to
set, and then press [ENTER].
For TUNER input selector only “Anlg (Analog)”
will be available.
True: Specifies the default listening mode for
Dolby TrueHD sources, such as Blu-ray or HD
DVD (input via HDMI).
MSTR: Specifies the default listening mode for
DTS-HD Master Audio sources, such as Blu-ray
or HD DVD (input via HDMI).
Use the Up and Down [q]/[w] buttons to
4
select the signal format that you want to
[e]/[r] buttons to select a listening
mode.
Only listening modes that can be used with each
input signal format can be selected (see pages 62-
65).
DSD: Specifies the default listening mode for
DSD multichannel sources, such as SACD.
The Last Valid option means that the listening
mode selected last will be used.
When you’ve finished, press the [SETUP]
button.
5
Setup closes.
Notes:
• If you connect an input component (such as UP-A1
series Dock that seated iPod or iPhone) to the UNI-
VERSAL PORT jack, you can assign only “Anlg
(Analog)” listening mode to PORT input selector.
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
IntelliVolume
Source Setup
With IntelliVolume, you can set the input level for each
input selector individually. This is useful if one of your
source components is louder or quieter than the others.
Use the Left and Right [e]/[r] buttons to set the level.
If a component is noticeably louder than the others, use
the Left [e] button to reduce its input level. If it’s notice-
ably quieter, use the Right [r] button to increase its
input level. The input level can be adjusted from −12 dB
to +12 dB in 1 dB steps.
This section explains items on the “Source Setup” menu.
Items can be set individually for each input selector.
Press the input selector buttons to select
an input source, and then press the
[RECEIVER] button.
1
Press the [SETUP] button.
2
Note:
Use the Up and Down [q]/[w] buttons to
IntelliVolume does not apply for Zone 2.
3
select “4. Source Setup”, and then press
[ENTER].
A/V Sync
When using your DVD player’s progressive scanning
function, you may find that the picture and sound are out
of sync. With the A/V Sync setting, you can correct this
by applying a delay to the audio signal.
Use the Up and Down [q]/[w] buttons to
4
select an item, and then press [ENTER].
Use the Left and Right [e]/[r] buttons to
5
change it.
The delay can be set from 0 to 100 milliseconds (msec)
in 10 millisecond steps.
The “Source Setup” menu items are explained
below.
Use the Left and Right [e]/[r] buttons to set the delay.
To view the TV picture while setting the delay.
When you’ve finished, press the [SETUP]
button.
Setup closes.
6
If HDMI Lip Sync is “enabled” (see page 79), and your
TV or display supports HDMI Lip Sync, the displayed
delay time will be the A/V Sync delay time. The HDMI
Lip Sync delay time is displayed underneath in
parentheses.
Note:
A/V Sync is disabled when the Pure Audio listening
mode is selected, or when the Direct listening mode is
used with an analog input source.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Volume Setup
Miscellaneous (Volume) Setup
This section explains the items on the “Miscellaneous”
menu.
■ MaxVolume
With this setting, you can limit the maximum volume.
The Maximum Volume range is “Off”, 79 to 30.
Press the [RECEIVER] button followed by
the [SETUP] button.
1
■ POnVol
With this preference, you can specify the volume setting
to be used each time the AV receiver is turned on.
The range is “Last”, “Min”, 1 to 79 or “Max”.
To use the same volume level that was used when the AV
receiver was turned off, select “Last”.
The “POnVol” cannot be set higher than the “Max
Volume” setting.
Use the Up and Down [q]/[w] buttons to
2
select “6. Miscellaneous”, and then press
[ENTER].
Press the [ENTER] button.
3
Use the Up and Down [q]/[w] buttons to
4
select an item, and use the Left and Right
[e]/[r] buttons to change it.
■ HP Level
With this preference, you can specify the headphone
volume relative to the main volume. This is useful if
there’s a volume difference between your speakers and
your headphones. The headphones level can be set from
–12 dB to +12 dB.
The items are explained below.
When you’ve finished, press the [SETUP]
5
button.
Setup closes.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Tuner
Hardware Setup
This section explains items on the “Hardware Setup”
menu.
■ FM/AM (North American models)
See “AM/FM Frequency Step Setup” on page 53.
Press the [RECEIVER] button followed by
the [SETUP] button.
■ AM Freq (Asian models)
See “AM/FM Frequency Step Setup” on page 53.
1
Use the Up and Down [q]/[w] buttons to
2
HDMI
select “7. HardwareSetup”, and then
press [ENTER].
■ AudioTVOut
Use the Up and Down [q]/[w] buttons to
This preference determines whether audio received at
the HDMI IN is output by the HDMI OUT. You may
want to turn this preference on if your TV is connected
to the HDMI OUT and you want to listen to the audio
from a component that’s connected to an HDMI IN,
through your TV’s speakers. Normally, this should be set
to “Off”.
3
select an item, and then press [ENTER].
Use the Up and Down [q]/[w] buttons to
4
select an item, and use the Left and Right
[e]/[r] buttons to change it.
The items are explained below.
When you’ve finished, press the
5
Off: HDMI audio is not output (default).
[SETUP] button.
Setup closes.
On: HDMI audio is output.
Notes:
• If “On” is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
• If “On” is selected, “TV Sp On” appears on the Dis-
play by pressing the [DISPLAY] button.
• When “TV Ctrl” is set to “On”, this setting is fixed to
“Auto”.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Remote ID
• With some TVs and input signals, no sound may be
output even when this setting is set to “On”.
• When the “AudioTVOut” setting is set to “On”, or
“TV Ctrl” is set to “On” and you’re listening through
your TV’s speakers (see page 28), if you turn up the
AV receiver’s volume control, the sound will be output
by the AV receiver’s front left and right speakers. To
stop the AV receiver’s speakers producing sound,
change the settings, change your TV’s settings, or turn
down the AV receiver’s volume.
■ Remote ID
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To
differentiate the AV receiver from the other components,
you can change its remote ID from 1, the default, to 2 or
3.
Note:
If you do change the AV receiver’s remote ID, be sure to
change the remote controller to the same ID (see below),
otherwise, you won’t be able to control it with the remote
controller.
Changing the Remote Controller’s ID
While holding down the [RECEIVER]
1
button, press and hold down the [SETUP]
button until the Remote Indicator lights up
(about 3 seconds).
Use the number buttons to enter ID 1, 2, or
3.
2
The Remote Indicator flashes twice.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
■ LipSync
AV receiver, the name of the DVD player is displayed
on the AV receiver.
• Set to “Off” when a connected piece of equipment is
not compatible or it is unclear whether the equipment
is compatible or not.
• If movement is unnatural when set to “On”, change the
setting to “Off”.
• Refer to the connected component’s instruction
manual for details.
The AV receiver can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Disable: HDMI lip sync disabled (default).
Enable: HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the A/V Sync screen
(see page 76).
Power Ctrl
To link the power functions of
-compatible
components connected via HDMI, select “On”.
This setting is set to “On” automatically when the above
“HDMI Ctrl” is set to “On” first time.
■ xvColor
If your HDMI source and HDMI-compatible TV both
support the “x.v.Color,” you can enable “xvColor” on the
AV receiver with this setting.
Off: Power Control disabled.
On: Power Control enabled.
Notes:
• The “Power Ctrl” setting can be set only when the
above “HDMI Ctrl” setting is set to “On”.
Disable: “x.v.Color” disabled (default).
Enable: “x.v.Color” enabled.
Notes:
• If the color is unnatural when “xvColor” is set to
“Enable”, change the setting to “Disable”.
• Refer to the connected component’s instruction
manual for details.
• HDMI power control only works with
-
compatible components that support it and may not
work properly with some components due to their
settings or compatibility.
• When set to “On”, power consumption will increase.
• When set to “On”, regardless of whether the AV
receiver is On or on Standby, both audio and video
received by an HDMI input will be output by the
HDMI OUT for playback on the TV or other
component that’s connected to the HDMI OUT.
• Refer to the connected component’s instruction
manual for details.
■ HDMI Ctrl
This function allows
-compatible components
connected via HDMI to be controlled with the AV
receiver.
Off:
On:
disabled (default).
enabled.
TV Ctrl
Notes:
Set to “On” when you want to control the AV receiver
•
, which stands for Remote Interactive over
from an
HDMI.
-compatible TV that is connected to
HDMI, is the name of the system control function
found on Onkyo components. The AV receiver can be
used with CEC (Consumer Electronics Control),
which allows system control over HDMI and is part of
the HDMI standard. CEC provides interoperability
between various components, however, operation with
Off: TV Control disabled.
On: TV Control enabled.
Notes:
• Do not assign the component connected with the
HDMI input to the TV/TAPE selector when you set
“TV Control” setting to “On”. Otherwise, appropriate
CEC (Consumer Electronics Control) operation is not
guaranteed.
• Set to “Off” when the TV is not compatible or when it
is unclear whether the TV is compatible or not.
• The “TV Ctrl” setting can be set only when the above
“HDMI Ctrl” and “Power Ctrl” settings are both set to
“On”.
components other than
-compatible
components cannot be guaranteed.
When set to “On” and close the menu, the name of
connected
-compatible components and
“RIHD On” are displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the
component, it is displayed as “Player*” or
“Recorder*”, etc (“*” means the number of two or
more component).
• Refer to the connected component’s instruction
manual for details.
When set to “Off” and close the menu, “RIHD Off”
are displayed on the AV receiver.
76
Note:
“Disconnect” → “RIHD Off”
After changing the settings of the “HDMI Ctrl”,
“Power Ctrl”, or “TV Ctrl”, turn off the power to all
connected pieces of equipment and then turn them
on again. Refer to the User’s Manuals for all
connected pieces of equipment.
• When an
-compatible component is con-
nected to the AV receiver via the HDMI cable, the
name of the connected component is displayed on the
AV receiver display. For example, while you are
watching TV broadcasting, if you operate a DVD
player (being powered on) by the remote control of the
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Zone 2
In addition to your main listening room, you can also enjoy playback in the other room, or as we call Zone 2. And, you
can select a different source for each room.
Connecting Your Zone 2 Speakers to an
Amp in Zone 2
Connecting Zone 2
Connecting Your Zone 2 Speakers Directly
to the AV receiver
This setup allows 7.1-channel playback in your main
listening room and 2-channel stereo playback in Zone 2,
with a different source in each room.
This setup allows 5.1-channel playback in your main
room and 2-channel stereo playback in Zone 2, with a
different source in each room. This is called Powered
receiver. Note that when Powered Zone 2 is turned off,
you can enjoy 7.1-channel playback in your main room.
Hookup
• Use an RCA audio cable to connect the AV receiver’s
ZONE 2 LINE OUT L/R jacks to an analog audio
input on your Zone 2 amp.
• Connect your Zone 2 speakers to the speaker
terminals on your Zone 2 amp.
To use this setup, you must set the “Powered Zone 2”
setting to “Act” (see page 81).
Main room
TV
Hookup
Connect your Zone 2 speakers to the AV receiver’s
ZONE 2 SPEAKERS L/R speaker terminals.
Main room
AV receiver
TV
ZONE 2
LINE OUT
L
R
AV receiver
Zone 2
IN
R
L
Receiver/
integrated amp
Zone 2
Note:
The Zone 2 volume must be set on the Zone 2 amp.
L
R
Notes:
• With this setup, the Zone 2 volume is controlled by the
AV receiver.
• “Powered Zone 2” cannot be used if “Sp Type” is set
to “Bi-Amp” (page 44).
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Zone 2—Continued
Setting the Powered Zone 2
Use the Up and Down [q]/[w]
buttons to select “2-1. Sp
Settings”, and then press
[ENTER].
3
If you’ve connected your Zone 2 speakers to the AV
receiver, as explained in “Connecting Your Zone 2
Speakers Directly to the AV receiver” on page 80, you
must set the “PwrdZ2” (Powered Zone 2) setting to
“Act” (Activated).
RECEIVER
Use the Up and Down [q]/[w]
4
5
buttons to select “PwrdZ2”.
qwer
ENTER
SETUP
Use the Left and Right [e]/[r]
buttons to select:
NotAct: ZONE 2 SPEAKERS L/R
speaker terminals not
activated (Powered Zone 2
disabled).
Act: ZONE 2 SPEAKERS L/R
speaker terminals activated
(Powered Zone 2 enabled).
Press the [RECEIVER] button,
followed by the [SETUP] button.
1
Press the [SETUP] button.
Setup closes.
6
Notes:
• When “Act” is selected and Zone 2 turned on, the
Zone 2 speakers connected to the ZONE 2
SPEAKERS L/R speaker terminals output sound, but
the surround back speakers connected to the SURR
BACK L/R speaker terminals do not. When “Act” is
selected and Zone 2 turned off, the surround back
speakers output sound as normal.
Use the Up and Down [q]/[w]
2
buttons to select “2. Speaker
Setup”, and then press [ENTER].
• When the “Powered Zone 2” setting is set to “Act” and
the input selector of Zone 2 is selected, power con-
sumption on standby mode slightly increases.
• “Powered Zone 2” cannot be used if “Sp Type” is set
to “Bi-Amp” (page 44).
• This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Zone 2—Continued
Controlling Zone 2 with the Remote
Controller
Using Zone 2
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust
the volume for Zone 2.
ZONE2
ON/STANDBY
Controlling Zone 2 from the AV receiver
INPUT
SELECTOR
ZONE 2
OFF
Note:
To control Zone 2, you must press the remote
controller’s [ZONE 2] button first.
ZONE 2 indicator Input selector
Press the [ZONE 2] button, then
point the remote controller at the
AV receiver and press the
[ON/STANDBY] button.
Zone 2 turns on and ZONE 2 indicator
lights up.
1
To turn on Zone 2 and select an
input source, press the [ZONE 2]
button followed by an input
1
selector button within 8 seconds.
Zone 2 turns on and ZONE 2 indicator
lights up.
To select the same source as that of the
main room, press the [ZONE 2] button
repeatedly until “Z2 Sel: Source”
appears.
To select an input source for
Zone 2, press the [ZONE 2]
button, followed by an INPUT
SELECTOR button.
2
To select AM or FM press the
[TUNER] input selector button
repeatedly.
To select AM or FM press the
[TUNER] INPUT SELECTOR button
repeatedly.
Note:
You cannot select different AM or FM
radio stations for your main room,
Zone 2. The same AM/FM radio station
will be heard in each room.
Note:
You cannot select different AM or FM
radio stations for your main room,
Zone 2. The same AM/FM radio station
will be heard in each room.
To turn off Zone 2, press the
ZONE 2 [OFF] button.
2
To turn off Zone 2, press the
[ZONE 2] button, followed by the
[ON/STANDBY] button.
3
Notes:
• Only analog input sources are output by Zone 2.
Digital input sources are not output. If no sound is
heard when an input source is selected, check to make
sure it’s connected to an analog input.
• While Zone 2 is on, the Auto Power On/Standby and
Direct Change u functions do not work.
• While Powered Zone 2 is being used, listening modes
that require surround back or front high speakers
(6.1/7.1), such as Dolby Digital EX, DTS-ES and
Dolby Pro Logic IIz Height are unavailable.
• When the “Powered Zone 2” setting is set to “Act” and
the input selector of Zone 2 is selected, power
consumption on standby mode slightly increases.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Zone 2—Continued
Adjusting the Volume of Zones
On the remote controller, press
the [ZONE 2] button, and then
Remote
controller
use the VOL [q]/[w] button.
On the AV receiver, press the
[ZONE 2] button (the ZONE 2
indicator and Zone 2 selector on
the display flashes) and then use
the [–]/[+] buttons within 8
seconds.
AV receiver
Muting Zones
On the remote controller, press
the [ZONE 2] button, and then
press the [MUTING] button.
Remote
controller
To unmute a zone, on the remote
controller, press the [ZONE 2]
button, and then press the
[MUTING] button again.
Note:
Zones can also be unmuted by adjusting the volume.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components
You can control your DVD player, CD player, and other
components with the AV receiver’s remote controller.
To control another component, you must first enter that
component’s remote control code to a REMOTE MODE
button.
Look up the component’s remote
control code in the separate
Remote Control Codes list.
1
The codes are organized by category.
This section explains how to enter remote control codes
and how to control your other components.
While holding down the REMOTE
MODE button to which you want
to enter a code, press and hold
down the [DISPLAY] button until
the Remote indicator lights up
(about 3 seconds).
2
Preprogrammed Remote Control
Codes
The following REMOTE MODE buttons are
preprogrammed with remote control codes for
enter a remote control code to control these components.
For details on controlling these components, see the
pages indicated.
Notes:
• Remote control codes cannot be
entered for the [RECEIVER] and
[ZONE 2] buttons.
• Only TV remote control codes can be
entered for the [TV] button.
• Apart from the [RECEIVER], [TV],
control codes from any category can
be entered for the REMOTE MODE
buttons. However, these buttons also
work as input selector buttons
(page 49), so choose a REMOTE
MODE button that corresponds with
the input to which you connect your
component. For example, if you
connect your CD player to the CD
input, choose the [CD] button when
entering its remote control code.
Onkyo DVD/BD player (page 87)
Onkyo CD player (page 90)
(3 seconds)
Onkyo cassette recorder with u (page 92)
Onkyo Dock (pages 58, 91)
Entering Remote Control Codes
You’ll need to enter a code for each component that you
want to control.
Remote
indicator
DISPLAY
Within 30 seconds, use the
number buttons to enter the 5-
digit remote control code.
The Remote indicator flashes twice.
If the remote control code is not entered
successfully, the Remote indicator will
flash once slowly.
REMOTE
MODE
3
RECEIVER
Note:
The remote control codes provided are correct at the time
of printing but subject to change.
Number
buttons
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Note:
Remote Control Codes for Onkyo
If you connect an u-capable Onkyo RI Dock to the
Components Connected via u
TV/TAPE IN, CBL/SAT IN or VCR/DVR IN jacks, for
u to work properly, you must set the Input Display
accordingly (see page 45).
Onkyo components that are connected via u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
Resetting REMOTE MODE Buttons
You can reset a REMOTE MODE button to its default
remote control code.
Make sure the Onkyo component is
1
connected with an u cable and an
analog audio cable (RCA).
See page 39 for details.
While holding down the REMOTE
1
MODE button that you want to
reset, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3
seconds).
Enter the appropriate remote control code
to the REMOTE MODE button.
2
• [DVD/BD] button
31612: Onkyo DVD player with u
• [CD] button
71327: Onkyo CD player with u
• [TV/TAPE] button
42157: Onkyo cassette recorder with u
(default)
• [PORT] button
(3 seconds)
82351: Onkyo Dock
• [TUNER] button
Within 30 seconds, press the
2
51805: To control the AV receiver’s tuner
(default)
REMOTE MODE button again.
The Remote indicator flashes twice,
indicating that the button has been
reset.
See the previous page for how to enter remote
control codes.
Each of the REMOTE MODE buttons
is preprogrammed with a remote
control code. When a button is reset, its
preprogrammed code is restored.
Press the REMOTE MODE button, point
the remote controller at the AV receiver,
and operate the component.
3
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via u, use
the following remote control codes:
Resetting the Remote Controller
You can reset the remote controller to its default settings.
• [DVD/BD] button
30627: Onkyo DVD player without u (default)
While holding down the
1
• [CD] button
[RECEIVER] button, press and
hold down the [AUDIO] button
until the Remote indicator lights
up (about 3 seconds).
71817: Onkyo CD player without u (default)
• [TV] button
11807: Onkyo TV (default)
If you want to control an Onkyo component by pointing
the remote controller directly at it, use the following
remote control codes:
32900: Onkyo BD player
32901: Onkyo HD-DVD player
70868: Onkyo MD player
71323: Onkyo CD recorder
82990: Onkyo RI Dock
(3 seconds)
Within 30 seconds, press the
2
[RECEIVER] button again.
The Remote indicator flashes twice,
indicating that the remote controller
has been reset.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a TV
a ON/STANDBY, TV [9] buttons
with the remote control code for your TV (TV/DVD
combination or TV/VCR combination), you can control
your TV with the following buttons.
Set the TV to On or Standby.
b TV VOL [q]/[w] button
Adjust the TV’s volume.
For details on entering a remote control code for a
different component, see page 84.
c TV [INPUT] button
Selects the TV’s external inputs.
The [TV] button is preprogrammed with the remote
control code for controlling a TV that supports the
d GUIDE button
Displays the program guide.
*1
. The TV must be able to receive remote
e Arrow [q]/[w]/[e]/[r] and ENTER buttons
control commands via
and be connected to the
Used to navigate menus and select items.
AV receiver via HDMI. If controlling your TV via
doesn’t work very well, program your TV’s
remote control code into the [TV] button and use the TV
remote mode to control your TV.
f SETUP button
Displays a menu.
g Playback buttons*
Play [1], Pause [3], Stop [2], Fast Reverse
[5], Fast forward [4], Previous [7], and
Next [6].
Press [TV] button first
These buttons works for combination devices.
h SEARCH, REPEAT, RANDOM, and PLAY
MODE buttons*
j
a
Function as colored buttons.
i Number buttons
TV
Enter numbers. 0 button enters 11 on some
components. +10 button* works as “--/---” button or
+10.
k
l
a
b
c
d
j DISPLAY button
Displays information.
k MUTING button
m
Mutes the TV.
e
f
l CH +/– button
Select channels on the TV.
n
o
m PREV CH button
Selects the previous or last channel.
n RETURN button
g
h
Exits the TV’s setup menu.
o AUDIO button*
Selects foreign language soundtracks and audio
formats (e.g., Dolby Digital or DTS).
p CLR button
i
Cancels functions and clears entered numbers, or
enters 12.
Notes:
p
• With some components, certain buttons may not work
as expected, and some may not work at all.
• Buttons marked with an asterisk (*) are not supported
by the
function.
*1 The
supported by the AV receiver is the
CEC system control function of the HDMI standard.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a DVD Player, or DVD Recorder
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your DVD
player (Blu-ray, HD DVD, or TV/DVD combination),
you can control your player with the following buttons.
a ON/STANDBY button
Sets the DVD player to On or Standby.
b TV [9] button
Set the TV to On or Standby.
The [DVD/BD] button is preprogrammed with the
remote control code for controlling an Onkyo DVD
player.
c TV [INPUT] button
Selects the TV’s external inputs.
d TV VOL [q]/[w] button
For details on entering a remote control code for a
different component, see page 84.
Adjust the TV’s volume.
e TOP MENU button
Displays a DVD’s top menu or a DVD’s title.
The [DVD/BD] buttons are preprogrammed with the
remote control code for controlling a component that
f Arrow [q]/[w]/[e]/[r] and ENTER buttons
*1
supports the
. The component must be able to
and be
connected to the AV receiver via HDMI. If controlling
your component via doesn’t work very well,
Used to navigate menus and select items.
receive remote control commands via
g SETUP button
Used to access the DVD player’s settings.
h Playback buttons
program your component’s remote control code into the
[DVD/BD] button and use the TV remote mode to
control your component.
Play [1], Pause [3], Stop [2], Fast Reverse
[5], Fast forward [4], Previous [7], and
Next [6].
i REPEAT button
Press the appropriate
REMOTE MODE button first
Used with the repeat playback function.
j SEARCH button*
Used to search title, chapter, and track numbers, and
to search times for locating specific points.
l
a
k Number buttons
Used to enter title, chapter, and track numbers, and
to enter times for locating specific points. The [+10]
m
n
l DISPLAY button
b
c
d
e
Displays information about the current disc, title,
chapter, or track, including elapsed time, remaining
time, total time, and so on.
o
m MUTING button (51)
p
Mutes or unmutes the AV receiver.
f
g
n DISC +/–, CH +/– button
Selects discs on a DVD changer. Selects TV
channels on a component with a built-in tuner.
q
r
o VOL [q]/[w] button (49)
Adjusts the volume of the AV receiver.
p MENU button
h
Displays a DVD’s menu.
q RETURN button
s
t
i
j
Exits the DVD player’s setup menu or returns to the
previous menu.
r AUDIO button*
Selects foreign language soundtracks and audio
formats (e.g., Dolby Digital or DTS).
k
s RANDOM button*
u
Used with the random playback function.
t PLAY MODE button*
Selects play modes on components with selectable
play modes.
*1 The
supported by the AV receiver is the
CEC system control function of the HDMI standard.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
and [PLAY MODE] buttons will work as colored or A,
u CLR button
B, C, D buttons. In this case, these buttons cannot be
used to set repeat playback, random playback, or
select play modes.
Cancels functions and clears entered numbers.
Notes:
• If you enter the remote control code for a HD DVD or
Blu-ray player that has A, B, C, and D or colored
buttons, the [SEARCH], [REPEAT], [RANDOM],
• Buttons marked with an asterisk (*) are not supported
by the
function.
Controlling a VCR or PVR
By pressing the REMOTE MODE button that’s been
(TV/VCR, PVR, DBS/PVR combination or cable/PVR
combination), you can control your video recorder with
the following buttons.
a ON/STANDBY button
Set the video recorder to On or Standby.
b TV [9] button
Set the TV to On or Standby.
c TV [INPUT] button
For details on entering a remote control code for a
different component, see page 84.
Selects the TV’s external inputs.
d TV VOL [q]/[w] button
Adjust the TV’s volume.
Press the appropriate
REMOTE MODE button first
e GUIDE button
Displays the program guide or navigation list.
f Arrow [q]/[w]/[e]/[r] and ENTER buttons
Used to navigate menus and select items.
a
j
g SETUP button
Displays the video recorders setup menu.
VCR
/
DVR
h Previous [7] button
k
l
Previous or instant replay function.
i Number buttons
b
c
d
e
Enter numbers. The [0] button enters 11 on some
components. The [+10] button works as a +10
button or “--/---” button.
m
n
j DISPLAY button
Displays information.
f
g
k MUTING button (51)
o
Mutes or unmutes the AV receiver.
l CH +/– button
Selects TV channels on the video recorder.
h
p
q
m VOL [q]/[w] button (49)
Adjusts the volume of the AV receiver.
n PREV CH button
Selects the previous channel.
o RETURN button
Exits the menu or returns to the previous menu.
i
p Next [6] button
Next or advance function.
r
q Playback buttons
Play [1], Pause [3], Stop [2], Rewind [5],
and Fast forward [4].
r CLR button
Cancels functions or enters the number 12.
Note:
With some components, certain buttons may not work as
expected, and some may not work at all.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a Satellite Receiver or Cable Receiver
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
satellite receiver, cable receiver, or DVD recorder
(DBS/PVR combination or cable/PVR combination),
you can control your player with the following buttons.
a ON/STANDBY button
Set the component to On or Standby.
b GUIDE button
Displays the onscreen program guide.
c Arrow [q]/[w]/[e]/[r] and ENTER buttons
For details on entering a remote control code for a
different component, see page 84.
Used to navigate menus and select items.
d SETUP button
Displays the setup menu.
e SEARCH, REPEAT, RANDOM, and PLAY
MODE buttons
Press the appropriate
REMOTE MODE button first
Function as colored buttons.
f Number buttons
g
Enter numbers. The [+10] button works as a +10
a
button or “--/---” button.
CBL/SAT
g DISPLAY button
Displays information.
h
i
h MUTING button (51)
Mutes or unmutes the AV receiver.
j
i CH +/– button
Selects satellite/cable channels.
j VOL [q]/[w] button (49)
k
b
c
d
Adjusts the volume of the AV receiver.
k PREV CH button
Selects the previous channel.
l
m
l RETURN button
Exits the menu.
m AUDIO button
n
Selects foreign language soundtracks and audio
formats (e.g., Dolby Digital or DTS).
n Playback buttons
e
f
Play [1], Pause [3], Stop [2], Fast Reverse
[5], Fast forward [4], Previous [7], and
Next [6].
o CLR button
Cancels functions and clears entered numbers.
Note:
o
With some components, certain buttons may not work as
expected, and some may not work at all.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a CD Player
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your CD
player, you can control your player with the following
buttons.
a ON/STANDBY button
Set the component to On or Standby.
b Arrow [q]/[w]/[e]/[r] and ENTER buttons*
Used to navigate menus and select items.
The [CD] button is preprogrammed with the remote
control code for controlling an Onkyo CD player.
c SETUP button*
Used to access the Onkyo CD player’s settings.
For details on entering a remote control code for a
different component, see page 84.
d Playback buttons
Play [1], Pause [3], Stop [2], Fast Reverse
[5], Fast forward [4], Previous [7], and
Next [6].
Press the appropriate
REMOTE MODE button first
e REPEAT button
Used with the repeat playback function.
f SEARCH button*
Used to locate specific points.
h
a
g Number buttons
CD
Used to enter track numbers and times for locating
specific points. The [+10] button works as a +10
button or “--/---” button.
i
j
h DISPLAY button
Displays information about the current disc or track,
including elapsed time, remaining time, total time,
and so on.
k
i MUTING button (51)
Mutes or unmutes the AV receiver.
b
c
j DISC +/– button
Selects discs on a CD changer.
k VOL [q]/[w] button (49)
Adjusts the volume of the AV receiver.
l RANDOM button
d
Used with the random playback function.
m PLAY MODE button*
Selects play modes on components with selectable
play modes.
l
m
e
f
n CLR button
Cancels functions and clears entered numbers.
g
Notes:
• Buttons marked with an asterisk (*) are not supported
by the RI control.
n
• With some components, certain buttons may not work
as expected, and some may not work at all.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling an RI Dock
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
Dock, you can control your iPod in the Dock with the
following buttons.
• Your iPod may not respond the first time you press this but-
ton, in which case you should press it again. This is because
the remote controller transmits the On and Standby com-
mands alternately, so if your iPod is already on, it will
remain on when the remote controller transmits an On com-
mand. Similarly, if your iPod is already off, it will remain
off when the remote controller transmits an Off command.
For some RI docks, the “ON/STANDBY” button may
u).
b TOP MENU button
In this case, make an u connection and enter a remote
control code 82351 (with u).
Works as a Mode button when used with a DS-A2
RI Dock.
For details on entering a remote control code,
see page 84.
c Arrow [q]/[w] and ENTER buttons
Used to navigate menus and select items.
When Using an RI Dock:
• Connect the RI Dock to the TV/TAPE IN, VCR/DVR
IN, or CBL/SAT IN L/R jacks.
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• Set the AV receiver’s Input Display to “DOCK”
(see page 45).
d Previous [7] button
Restarts the current song. Press it twice to select the
previous song.
e Rewind [5] button
Press and hold to rewind.
f Pause [3] button
• See to the Dock’s instruction manual for more information.
Pauses playback.
Press the appropriate
REMOTE MODE button first
g REPEAT button
Used with the repeat function.
h DISPLAY button
Turns on the backlight for 30 seconds.
a
h
i MUTING button (51)
Mutes or unmutes the AV receiver.
j ALBUM +/– button
i
j
Selects the next or previous album.
k VOL [q]/[w] button (49)
Adjusts the volume of the AV receiver.
k
l
m
l MENU button
Exits the menu.
b
c
m PLAYLIST [e]/[r] button
Selects the previous or next playlist on the iPod.
n Play [1] button
Starts playback. If the component is off, it will turn
on automatically.
n
o
o Next [6] button
d
e
f
Selects the next song.
p
q
r
s
p Fast Forward [4] button
Press and hold to fast forward.
q Stop [2] button
Stops playback and displays a menu.
g
r PLAY MODE button
Selects play modes on components with selectable
play modes.
Works as a Resume button when used with a DS-A2
RI Dock.
s RANDOM button
Used with the shuffle function.
a ON/STANDBY button
Turns the iPod on or off.
Notes:
Note:
With some components, certain buttons may not work as
expected, and some may not work at all.
• This button does not turn the Onkyo DS-A2 or DS-
A2X RI Dock on or off.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a Cassette Recorder
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
cassette recorder, you can control your cassette recorder
with the following buttons.
On twin cassette decks, only Deck B can be controlled.
a ON/STANDBY button
Turns the cassette recorder on or off.
b Previous and Next [7]/[6] buttons
The Previous [7] button selects the previous
track. During playback it selects the beginning of
the current track. The Next [6] button selects the
next track.
The [TV/TAPE] button is preprogrammed with the
remote control code for controlling an Onkyo cassette
recorder when used with an u connection.
For details on entering a remote control code for a
different component, see page 84.
Depending on how they were recorded, the Previous
and Next [7]/[6] buttons may not work
properly with some cassette tapes.
Press the appropriate
REMOTE MODE button first
c Rewind and Fast Forward [5]/[4]
buttons
The Rewind [5] button starts rewind. The Fast
Forward [4] button starts fast forward.
a
d Reverse Play [t] button
Starts reverse playback.
TV/TAPE
e Play [1] button
f
Starts playback.
f MUTING button (51)
g
Mutes or unmutes the AV receiver.
g VOL [q]/[w] button (49)
Adjusts the volume of the AV receiver.
h Stop [2] button
Stops playback.
Notes:
• With some components, certain buttons may not work
as expected, and some may not work at all.
• An Onkyo cassette recorder connected via u can
also be controlled in Receiver mode.
b
b
c
d
c
h
e
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.
designed for home theater enjoyment and has a wide
volume range for precise adjustment.
press the remote controller’s [MUTING] button to
unmute the AV receiver (page 51).
• While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers
(page 51).
• Check the digital audio output settings on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
• With some DVD-Video discs, you need to select an
audio format from a menu or with the [AUDIO] button
on your DVD player’s remote controller.
If you can’t resolve the issue yourself, try resetting
the AV receiver before contacting your Onkyo
dealer.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VCR/DVR]
button, press the [ON/STANDBY] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
you must connect one between it and the AV receiver.
connect an MC head amp, or an MC transformer and
a phono preamp.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
• Check the speaker settings (pages 68–70).
• If the digital signal format is set to PCM or DTS, set it
to “Auto” (page 52).
• If there’s no sound from a DVD player connected to an
HDMI IN, check the DVD player’s output settings,
and be sure to select a compatible audio format.
Power
Can’t turn on the AV receiver
• Make sure that the power cord is plugged into the wall
outlet properly.
• Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it back in again.
Only the front speakers produce sound
• When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer produce sound.
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 68).
The AV receiver turns off as soon as it’s turned
on
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet
immediately. Disconnect all speaker cables and input
sources, and leave the AV receiver with its power cord
disconnected for 1 hour. After that, reconnect the
power cord and set the volume to maximum. If the AV
receiver stays on, set the volume to minimum,
disconnect the power cord, and reconnect your
speakers and input sources. If the AV receiver turns off
when you set the volume to maximum, disconnect the
power cord, and contact your Onkyo dealer.
Only the center speaker produces sound
Logic IIx Music listening mode with a mono source,
such as an AM radio station or mono TV program, the
sound will be concentrated in the center speaker.
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 68).
The center speaker produces no sound
• When the Stereo or Mono listening mode is selected,
the center speaker produces no sound (page 66).
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 68).
Audio
There’s no sound or it’s very quiet
HDMI input, make sure that input is assigned to an
input selector (page 41).
• To listen to an audio source that’s connected to an
OPTICAL or COAXIAL input, make sure that input is
assigned to an input selector (page 43).
• Make sure that all audio connecting plugs are pushed
in all the way (page 25).
• Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with the
metal part of each speaker terminal (page 19).
• Make sure that the speaker cables are not shorting.
The surround speakers produce no sound
• When the T-D (Theater-Dimensional), Stereo or
speakers produce no sound.
mode, not much sound may be produced by the
surround speakers. Try another listening mode
(page 61).
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 68).
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
The front high speakers or surround back
speakers produce no sound
• An audio cable may be picking up interference. Try
repositioning your cables.
• Depending on the current listening mode, no sound
back speakers. Try another listening mode (page 61).
• Not much sound may be produced by the front high
speakers or surround back speakers with some sources.
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 68).
• While Powered Zone 2 is being used, playback in the
main room is reduced to 5.1-channels and the front
high speakers or surround back speakers produce no
sound (page 80).
The Late Night function doesn’t work
• Make sure that the source is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD (page 73).
About DTS signals
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.
• When DTS program material ends and the DTS
bitstream stops, the AV receiver remains in DTS
listening mode and the DTS indicator remains on. This
is to prevent noise when you use the pause, fast
forward, or fast reverse function on your player. If you
switch your player from DTS to PCM, as the AV
receiver does not switch formats immediately, you may
not hear anything, in which case you should stop your
player for about 3 seconds, and then resume playback.
• With some CD players, you won’t be able to playback
DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t
recognize it as a genuine DTS signal. In such cases,
you may hear noise.
The subwoofer produces no sound
• If the source material contains no audio in the LFE
channel, the subwoofer produces no sound.
• Check the “2-2. Sp Config (Speaker Configuration)”
(page 68).
The Zone 2 speakers produce no sound
• The Zone 2 speakers only output sources that are
connected to an analog input. Check to see if the
source component is connected to an analog input.
• “Powered Zone 2” cannot be used if “Sp Type” is set
to “Bi-Amp” (page 44).
There’s no sound with a certain signal format
• Check the digital audio output setting on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
• With some DVD-Video discs, you need to select an
audio format from a menu or with the [AUDIO] button
on your DVD player’s remote controller.
The beginning of audio received by an HDMI IN
can’t be heard
• Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio
Can’t get 6.1- or 7.1-channel playback
Video
• While Powered Zone 2 is being used, playback in the
main room is reduced to 5.1-channels and the
surround back speakers produce no sound (page 80).
There’s no picture
• Make sure that all video connecting plugs are pushed
in all the way (page 25).
• Make sure that each video component is properly
connected.
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
• While the Pure Audio listening mode is selected, the
video circuitry is turned off and only the HDMI OUT
outputs video signals.
• The AV receiver does not convert between formats, so
component video input, your TV must be connected to
the component video output (page 26).
• If the video source is connected to an HDMI input,
your TV must be connected to the HDMI OUT
(page 26).
Can’t select the Pure Audio listening mode
• The Pure Audio listening mode cannot be selected
while Zone 2 is on.
• The Pure Audio listening mode is not available on the
North American models.
The volume cannot be set to 79
• Check to see if a maximum volume has been set
(page 77).
adjusted to high positive values (page 70), then the
Note that the individual speaker volume levels are set
automatically after the Audyssey 2EQ™ Room Cor-
rection and Speaker Setup function has been com-
pleted (page 46).
• When the levels of each speaker have been adjusted
(page 70), the maximum possible volume may be
reduced.
There’s no picture from a source connected to
an HDMI IN
• Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not supported (page 28).
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on can degrade audio
performance, so don’t use them.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
• If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that your TV does not
support the current video resolution and you need to
select another resolution on your DVD player.
Dock for iPod or iPhone
There’s no sound
• Make sure your iPod or iPhone is playing.
• Make sure your iPod or iPhone is inserted properly in
the Dock.
Tuner
• Make sure the UP-A1 series Dock is connected to the
UNIVERSAL PORT jack on the AV receiver.
• Make sure the AV receiver is turned on, the correct
input source is selected, and the volume is turned up.
• Make sure the plugs are pushed in all the way.
• Try resetting your iPod or iPhone.
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
light up
• Relocate your antenna.
• Move the AV receiver away from your TV or
computer.
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
There’s no video
• Make sure that your iPod or iPhone’s TV OUT setting
is set to On.
• Make sure the correct input is selected on your TV or
the AV receiver.
• Some versions of the iPod or iPhone do not output
video.
The AV receiver’s remote controller doesn’t
control your iPod or iPhone
• Make sure your iPod or iPhone is properly inserted in
the Dock. If your iPod or iPhone is in a case, it may
not connect properly to the Dock. Always remove
your iPod or iPhone from the case before inserting it
into the Dock.
• The iPod or iPhone cannot be operated while it’s
displaying the Apple logo.
• Make sure you’ve selected the right remote mode.
• When you use the AV receiver’s remote controller,
point it toward your amp.
Remote Controller
The remote controller doesn’t work
correct polarity (page 16).
away from the AV receiver and there’s no obstruction
remote control sensor (page 16).
• Make sure you’ve selected the correct remote
controller mode (pages 17 and 86–92).
• Make sure you’ve entered the correct remote control
code (page 84).
• If you still can’t control your iPod or iPhone, start
playback by pressing your iPod or iPhone’s Play
button. Remote operation should then be possible.
• Try resetting your iPod or iPhone.
Can’t control other components
• Make sure you’ve selected the correct remote
controller mode (pages 17 and 86–92).
• If you’ve connected an u-capable Onkyo RI Dock to
the TV/TAPE IN, CBL/SAT IN or VCR/DVR IN
jacks, for the remote controller to work properly, you
must set the Input Display to “DOCK” (page 45).
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
work as expected, and some may not work at all.
• To control an Onkyo component that’s connected via
u, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 85).
• Depending on your iPod or iPhone, some buttons may
not work as expected.
The AV receiver unexpectedly selects your iPod
or iPhone as the input source
• Always pause iPod or iPhone playback before
selecting a different input source. If playback is not
paused, the Direct Change function may select your
iPod or iPhone as the input source by mistake during
the transition between tracks.
• To control an Onkyo component that’s not connected
via u, or another manufacturer’s component, point
the remote controller at that component. Be sure to
enter the appropriate remote control code first
(page 84).
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
Recording
Can’t record
• On your recorder, make sure the correct input is
settings.
selected.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
• To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TV/TAPE IN to TV/TAPE
OUT or VCR/DVR IN to VCR/DVR OUT).
• When the Pure Audio listening mode is selected,
video recording is not possible because no video
signals are output. Select another listening mode.
2. Use the Left and Right [e]/[r] buttons to change
the setting.
3. Press the input selector button for the input source
that you want to set when you’ve finished.
• Video Attenuation
Others
This setting can be made for the DVD/BD,
VCR/DVR, CBL/SAT, or AUX input.
If you have a games console connected to the
composite video input, and the picture isn’t very
clear, you can attenuate the gain.
The sound changes when I connect my
headphones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio, in which case it stays the
same. (Pure Audio listening mode is not available for
North American models.)
Video ATT:0: (default).
Video ATT:2: Gain is reduced by 2 dB.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least 5 seconds, and then plug it back
in again.
How do I change the language of a multiplex
source
• On the “Audio Adjust” menu, change the “Input
The u functions don’t work
• To use u, you must make an u connection and an
analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally (page 39).
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
this unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
• While Zone 2 is selected, the u functions don’t
work.
The AV receiver’s display doesn’t work
• The display is turned off when the Pure Audio
listening mode is selected. Select another listening
mode.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to Standby.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
HT-R670
Amplifier Section
General
Rated Output Power
North American:
Power Supply
North American:
Asian:
Power Consumption
North American:
Asian:
AC 120 V, 60Hz
AC 220 V – 240V, 50/60 Hz
130 watts minimum continuous power
per channel, 6 ohms, at 1 kHz with a
maximum total harmonic distortion of
4.9 A
470W
1%
Asian:
Dimensions (W × H × D)
7 ch × 130 W at 6 ohms, 1kHz (IEC)
Maximum Output Power
Dynamic Power
435 × 151.5 × 329 mm
Asian:
(17-1/8" × 5-15/16"× 12-15/16")
7 ch × 160 W at 6 ohms, 1kHz (JEITA)
180 W (3Ω, Front)
160 W (4Ω, Front)
100 W (8Ω, Front)
Weight
North American:
8.9 kg
19.6 lbs.
9.7 kg
Asian:
THD (Total Harmonic Distortion)
0.08% (1 kHz 1 W)
60 (Front, 1 kHz, 8Ω)
Input Sensitivity and Impedance
200 mV/ 47 kΩ (LINE)
Output Level and Impedance
200 mV/ 2.2 kΩ (REC OUT)
21.4 lbs.
Damping Factor
■ Video Inputs
HDMI
Component
Composite
IN 1, IN 2, IN 3, IN 4
IN 1, IN 2
DVD/BD, CBL/SAT, VCR/DVR, AUX
Frequency Response
Tone Control
5 Hz–100 kHz/ +1 dB–3 dB (Direct mode)
10 dB, 50 Hz (BASS)
10 dB, 20 kHz (TREBLE)
106 dB (LINE, IHF-A)
North American:
■ Video Outputs
HDMI
Component
Composite
OUT
OUT
Signal to Noise Ratio
Speaker Impedance
VCR/DVR (REC OUT),
MONITOR OUT
6Ω–16Ω
Asian:
4Ω–16Ω
■ Audio Inputs
Digital Inputs
COAXIAL:2
OPTICAL :2
Video Section
Analog Inputs
DVD/BD, VCR/DVR, CBL/SAT,
TV/TAPE, CD, AUX (PORTABLE)
Input Sensitivity/Output Level and Impedance
1 Vp-p /75Ω (Component Y)
■ Audio Outputs
0.7 Vp-p /75Ω (Component Pb/Cb, Pr/Cr)
1 Vp-p /75Ω (Composite)
Analog Outputs
Subwoofer Pre Output
Speaker Outputs
VCR/DVR, TV/TAPE, ZONE 2
1
Main (L, R, C, SL, SR, SBL, SBR)
+ ZONE2 /Front High (L, R)
Component Video Frequency Response
5 Hz – 50 MHz, –3 dB
Phones
1
Tuner Section
■ Control Terminal
FM Tuning Frequency Range
North American:
MIC
Yes
87.5 MHz – 107.9 MHz
Asian:
87.5 MHz – 108.0 MHz
AM Tuning Frequency Range
Specifications and features are subject to change without
notice.
North American:
530 kHz – 1710 kHz
Asian:
522/530 kHz – 1611/1710 kHz
Preset Channel
40
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications—Continued
■ Surround/Surround Back Speaker
HTP-670
(SKR-670/SKB-670)
■ Powered Subwoofer (SKW-770)
Type:
Impedance:
Maximum input power: 130 W
Sensitivity:
Frequency response:
Cabinet capacity:
Dimensions
(W × H × D):
Full-Range closed box
6 Ω
Type:
Input sensitivity/Impedance:
140 mV/20 kΩ
Maximum output power:290 W (Dynamic power)
Bass-reflex
80 dB/W/m
70 Hz–20 kHz
2.1 L (0.074 cubic feet)
Frequency response:
Cabinet capacity:
Dimensions
25 Hz–150 Hz
37 L (1.3 cubic feet)
120 × 231 × 122 mm
(4-3/4" × 9-1/8" × 4-13/16")
(incl. grille and projection)
0.8 kg (1.8 lbs.)
8 cm (3-1/4") Cone Speaker
Spring type color coded
2
(W × H × D):
275 × 507 × 411 mm
(10-13/16" × 19-15/16" × 16-3/16")
Weight:
Weight:
Drivers unit:
Power supply
11.6 kg (25.6 lbs.)
25 cm (10") Cone Woofer
North American:
AC 120 V, 60 Hz
Asian:
Drivers unit:
Terminal:
Keyhole slot:
Grille:
Fixed
AC 220 V – 240V, 50/60 Hz
North American:
163 W
Asian:
137 W
Power consumption
Other:
UP-A1
Dimensions
(W × H × D):
Auto Standby function
83 × 33 × 74 mm
(3-1/4" × 1-5/16" × 2-15/16")
■ Front Speaker (SKF-670)
Weight:
170 g (6 ounces)
Type:
2 Way closed box
Impedance:
Maximum input power: 130 W
6 Ω
Sensitivity:
81 dB/W/m
Frequency response:
Crossover frequency:
Cabinet capacity:
Dimensions
60 Hz–50 kHz
4 kHz
2.1 L (0.074 cubic feet)
Specifications and features are subject to change without
notice.
(W × H × D):
120 × 231× 122 mm
(4-3/4" × 9-1/8" × 4-13/16")
(incl. grille and projection)
1.1 kg (2.4 lbs.)
Weight:
Drivers unit:
10 cm (4") Cone woofer
2.5 cm (1") Balanced dome
Spring type color coded
2
Terminal:
Keyhole slot:
Grille:
Fixed
■ Center Speaker (SKC-670)
Type:
2 Way closed box
Impedance:
Maximum input power: 130 W
6 Ω
Sensitivity:
81 dB/W/m
Frequency response:
Crossover frequency:
Cabinet capacity:
Dimensions
60 Hz–50 kHz
4 kHz
2.1 L (0.074 cubic feet)
(W × H × D):
231× 121× 128 mm
(9-1/8" × 4-3/4" × 5-1/16")
(incl. grille and projection)
1.1 kg (2.4 lbs.)
Weight:
Drivers unit:
10 cm (4") Cone woofer
2.5 cm (1") Balanced dome
Spring type color coded
2
Terminal:
Keyhole slot:
Grille:
Fixed
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
Y0905-1
SN 29344937
(C) Copyright 2009 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 9 3 7 *
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miele Ventilation Hood 09 968 440 User Manual
Miele Washer W 820 User Manual
NEC Computer Monitor NLT 15 User Manual
NEC Projector pa500x User Manual
Nikon Camera Flash SL 1 User Manual
Nikon Microscope Magnifier 44100 User Manual
Niles Audio Washer PHD42 User Manual
Nilfisk Advance America Vacuum Cleaner GD 910 User Manual
Panasonic CRT Television CT 27D20U User Manual
Panasonic Network Card 2SC4835G User Manual