32
"
TFT LCD TV
NLT-32W
32inch
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Service
Never remove the back cover of the TV, this can expose you to high voltage and
other hazards. If the TV does not operate properly, unplug it and call your nearest
NEC Service Centre.
Connect the antenna cable to the connection marked Ant. (on the rear). For best
reception, use an outdoor antenna.
Location
Position your TV so that no bright light or sunlight will shine directly on the screen. Do
not expose the TV to vibration, moisture, dust or heat. Also ensure that the TV is
placed in a position that allows a free flow of air. Do not cover the ventilation
openings on the back cover. You can install the TV on a wall or place it on a table-top
or similar flat surface. Mounted the TV securely to eliminate the risk of injury from the
TV falling.
Cleaning
Unplug the TV before cleaning the face of the LCD Screen. Dust the TV by wiping the
screen and cabinet with a soft, clean cloth. If the screen requires additional cleaning,
use a clean, damp cloth. Do not use liquid or aerosol cleaners.
Image Persistence
Avoid displaying fixed pattern in the monitor for long period of time to avoid image
persistence.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before operating the set, please read this manual carefully.
Warnings
Contents
2~3
4
Supplied Accessories
Controls
5
6~8
6
7~8
9
9
9
9
9
Controller of panel
Remote controller
Basic Operation
Turning the TV On and Off
Programme selection
Volume adjustment
Q.View
Sound mute function
On screen Language selection
On Screen Menus and Displays
Setting up TV Programme
Auto Programme
Manual Programme
Programme Edit
Picture Control
Manual picture control
Auto picture control
Sound Control
Other functions
Clock
9
9
10
11~13
11
12
13
14
14
14
15~16
17~18
17
Blue Back
17
Sleep timer
Auto Sleep
17
18
Childlock
Radio
18
18
ARC
Radio Control
18
19
Other functions
Teletext
20
21~22
21
Text On/Off
TOP text
FLOF text
21
21
Special Teletext function
External Equipment Connection
Antenna connection
COMPONENT Input
DTV Input
22
23~24
23
23
23
24
A/V Input
A/V Output
S-VIDEO Input
24
24
Headphone jack
Connecting the PC as a monitor
Product specification
Troubleshooting
NEC Service Centres
24
25~28
29
30
31
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
L Make Sure the following accessories are provided with Product.
1. AC Cord
3. Batteries (type AAA)
2. Remote controller
5. PC IN cable
4. Owner’s manual
32
"
TFT LCD TV
NLT-32W
32inch
6. PC Audio IN cable
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
1. ON/OFF Switches TV set on or off.
2. MENU
Displays a menu.
3. + PR - (Programme Up/Down)
Selects a programme or a menu item.
4. + VOL - (Volume Up/Down)
Adjusts the volume./ Adjusts menu settings.
5. TV/AV Selects TV, COMPONENT, VIDEO, S-VIDEO, RADIO(Only when the set is
Radio On.), PC Analog, PC Digital or DTV mode./ Clears the menu from the screen.
6. Power Indicator
Illuminates in red when the TV is in standby mode./ Illuminates in green when the
TV is switched on. Illuminates in amber when the power save mode in PC mode.
(It's possible when the connected computer has a built in power management system
called PowerSaver. This system saves energy by switching the set into a low-power
mode when it has not been used for a certain amount of time.)
7. Remote control sensor
Accepts the IR signal of remote controller.
1
2
3
4
6
9
10
8
7
1. PC DIGITAL IN (DVI-I)
2. H/P (Headphone out)
Connect a headphone to this socket.
5
3. PC AUDIO IN
Connect the audio cable from the PC to the PC AUDIO IN of the set.
4. PC ANALOG IN (D-SUB)
5. COMPONENT IN
6. DTV IN
7. AV-IN
8. AV-OUT
9. S-VIDEO IN
Connect the output of the S -VIDEO on the VCR to the S-VIDEO input.
Connect the audio outputs of the S-VIDEO on the VCR to the Audio IN (L(MONO), R).
10. Ant. (Antenna input)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
All the functions can be controlled with the remote controller. Some functions can
also be adjusted with the buttons on the side panel of the set.
Remote controller
Before you use the remote controller, please install the batteries.
1. POWER
Turns the TV on from standby or off to standby mode.
2. MUTE
Turns the sound on and off.
3. NUMBER buttons
Selects programme numbers.
4. TV/AV
Selects TV, COMPONENT, VIDEO, S-VIDEO,
RADIO(Only when the set is Radio On.),
PC Analog, PC Digital or DTV mode.
5. MENU
Displays a main menu.
6. LIST
Displays the programme list menu.
7. I/II
Selects the language during dual language broadcast.
Selects the sound output.
8. SLEEP
Sets the sleep timer.
9. Q.VIEW
Returns to the previously viewed programme.
10. PRxy (Programme Up/Down)
Selects next programme or a menu item.
11. OK
Accepts your selection or displays the current mode.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
12. VOLÏq (Volume Up/Down)
Adjusts the sound level. Adjusts menu settings.
13. TV/PC
Selects TV or PC mode directly.
14. PSM (Picture Status Memory)
Recalls your preferred picture setting
15. SSM (Sound Status Memory)
Recalls your preferred sound setting
16. ARC
You can watch TV in various picture formats; Auto,
16:9, 14:9, 4:3, 16:9 Zoom, 14:9 Zoom, 4:3 Zoom.
Repeatedly press the ARC button to select your
desired picture format.
Note. 16:9 and 4:3 in PC mode are available.
17. TELETEXT buttons
These buttons are used for Teletext.
For further details, see the ‘Teletext’ section.
Battery installation
uInserting batteries
1. Remove the battery cover by pulling it
upward in the direction shown by the arrow.
2. Insert the batteries with correct polarity
( "+" to "+", and "-" to "-" ).
3. Replace the battery compartment cover.
→
→
* Install two high-quality 1.5V "AAA" alkaline batteries. Don't mix old batteries with
new batteries.
* Remove batteries when you won't use the remote controller for a long time. Liquid
leakage from old batteries may cause operation failure.
uNotes for using remote controller
• Make sure there are no objects between the remote controller and its sensor.
• Don't place the remote control near a heater or in damp place. Strong impact to the
remote control may cause operation failure.
• Signal from the remote control may be disturbed by sun light or other bright light. In
this case, darken the room or move the TV.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning the TV On and Off
Standby Setup: The AC power cord must be set up and
connected to have the TV in standby mode ready to be turned
on. Press the ON/OFF button on the side panel of the TV to go
into standby mode.
1. If the TV is in standby mode, press the POWER button
on the remote controller or the TV itself to turn the TV on.
2. Press the Power button again on the remote controller or
the ON/OFF button the TV itself to turn the TV off.
Note : If the TV is on and the POWER button is pressed to turn
the TV off, the TV goes into standby mode.
Programme selection
You can select a Programme number with the PRxy button
or NUMBER buttons.
Volume adjustment
Press the VOLÏq button to adjust the sound level.
Quick view
Press the Q.VIEW button to view the last Programme you were
watching.
Sound mute function
Press the MUTE( ) button. The sound is switched off and the
mute display
appears.
To cancel mute mode, press the MUTE( ) button again,
VOLÏq or SSM button.
On screen menu language selection
The menu can be displayed on the screen in desired
language. First, select your language.
1. Press the MENU button.
Language
English
Deutsch
Français
Español
Italiano
Nederlands
Portugues
2. Select the Setup menu, Then press VOLÏq.
3. Select the Language menu, then press VOLÏq.
4. Press the PRxy button to select your desired
language.
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
5. Press the TV/AV button.
All the on screen displays will appear in the selected
language.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Menus and Displays
1. Press the MENU button to display main menu.
Equalizer
2. Press the PRxy button to select menus-Picture,
Flat
Music
Movie
Speech
Sound, Special, Setup.
3. Adjust each menu with the VOLÏq button.
4. Press the MENU button to return to preceding
User
menu.
0.1 0.5 1.5ꢀ 5.0ꢀ10KHz
5. Press the TV/AV button to finish adjusting menu.
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
Picture
Menu
Picture
Sound
Special
Setup
q
q
q
q
Contrast
Brightness
Colour
90
75
75
60
Clock
Clock
Off Time
On Time
On Programme
--:--
Sharpness
--:-- Off
--:-- Off
1
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Adjustꢀ:ꢀ◀▶
Positionꢀ:▲▼
Nextꢀ:◀▶
Exitꢀ:ꢀTV/AV
Positionꢀ:▲▼
Adjustꢀ:ꢀ◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
Auto Programme
System
BG
Sound
Start
Equalizer
Balance
AVL
▶
0
Off
Surround
Sound Mode
Off
MONO
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
Adjustꢀ:ꢀ◀▶
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Nextꢀ:◀▶
Manual Programme
Programme
1
69
Channel
Table
System
V/UHF
BG
Search
Memorize
Name
▶▶▶
-----
Special
Positionꢀ:▲▼
Adjustꢀ:ꢀ◀▶
Clock
▶
Off
Off
Off
Off
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
Blue Back
Auto Sleep
Childlock
Radio
Programme Edit
P00-----
P05-----
P06-----
P07-----
P08-----
P09-----
■Name
■Skip
ARC
16:9
P01-----
P02-----
P03-----
P04-----
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Nextꢀ:◀▶
■Delete
■Move
Positionꢀ:▲▼◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Setup
Language
Auto Programme
▶
English
Manual Programme
Programme Edit
Language
▶
▶
▶
Deutsch
Français
Español
Italiano
Nederlands
Portugues
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Nextꢀ:◀▶
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up TV Programme
Once you have preset the programmes, you will be able to
use the PRxy or NUMBER buttons to scan the
Auto Programme
programmes you programmed.
Programmes can be tuned using automatic or manual
modes.
System
Start
BG
Auto Programme
All programmes that can be received are stored by this
method. It is recommended that you use Auto programme
during installation of this set.
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
Adjustꢀ:ꢀ◀▶
1. Press the MENU button.
2. Select the Setup menu, then press VOLÏq.
3. Select the Auto Programme menu,
then press VOLÏq.
4. Press the PRxy button to select System.
5. Select a TV system with the VOLÏq button;
BG : (Germany/Asia/M.East/Africa/Australia)
I
: (UK/Hong Kong/South Africa)
DK : (CIS/China/East Europe)
: (USA, Korea, Philippines)
M
6. Select Start, then press VOLÏq to start Auto
Programme.
7. Press the MENU button to stop Auto programme
8. Press the TV/AV button to return to normal TV
viewing.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up TV Programme
Manual Programme
Manual Programme
Manual Programme lets you manually tune and arrange
the programmes in whatever order you desire. Also you
can assign a programme name with 5 characters to each
programme number.
Programme
Channel
Table
1
69
V/UHF
BG
▶▶▶
System
Search
Memorize
Name
1. Press the MENU button.
-----
2. Select the Setup menu, then press VOLÏq.
3. Select Manual Programme menu, then press VOLÏq.
4. Select a programme with the VOLÏq button or
number buttons.
Positionꢀ:▲▼
Adjustꢀ:ꢀ◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
5. Press the PRxy button to select Channel menu.
6. Press the VOLÏq button or directly number buttons
to select a Channel.
7. Press the PRxy button to select the Table menu.
8. Press the VOLÏq button to select V/UHF or Cable
as required.
9. Select a TV system with the VOLÏq button.
BG : (Germany/Asia/M.East/Africa/Australia)
I
: (UK/Hong Kong/South Africa)
DK : (CIS/China/East Europe)
: (USA, Korea, Philippines)
M
10. Press the PRxy button to select Search menu.
When you press the VOLÏq buttons, the TV changes
programmes in sequence.
You will see all the programmes that the TV has
memorized. You will not see programmes that were
either erased or not memorized.
11. Press the PRxy button to select Memorize menu.
12. Press the VOLÏq button to store it.
13. Press the MENU button to return to prior menu.
14. Press the TV/AV button to return to normal TV
viewing.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up TV Programme
Programme Edit
Programme Edit
This function enables you to delete or skip the stored
programmes.
P00-----
P01-----
P02-----
P03-----
P04-----
P05-----
P06-----
P07-----
P08-----
P09-----
■Name
■Skip
Also you can move some programmes to other
programme numbers or insert a blank programme data into
the selected programme number.
1. Press the MENU button.
2. Select the Setup menu, then press VOLÏq.
3. Press the PRxy button select Programme Edit menu, then press VOLÏq.
4. Select the programme name to edit with the PRxy and VOLÏq button.
■Delete
■Move
Positionꢀ:▲▼◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Deleting a programme
1. Select a programme to be deleted with the PRxy or VOLÏq button.
2. Press the RED button once. The selected programme is deleted, all the
following programme is shifted up one position.
Naming a programme
1. Select a programme to be named with the PRxy or VOLÏq button.
2. Press the GREEN button. Then it display as below.
Edit Name
▲
Station
P01
-----
▼
Adjustꢀ:ꢀ▲▼◀▶
Confirm:ꢀOKꢀꢀ
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
3. Press the PRxy button repeatedly to edit programme name.
You can use the numeric 0 to 9, the alphabet A to z(capital
and small letters.) a blank and -. With the VOLÏq button,
you can select in the opposite direction.
4. Press the OK button to store it.
5. Press the MENU button to return to prior menu.
6. Press the TV/AV button to return to normal TV viewing.
Moving a programme
1. Select a programme to be moved with the PRxy or
VOLÏq button.
2. Press the YELLOW button.
3. Move the programme to desired programme number with
the PRxy or VOLÏq button.
4. Press the YELLOW button again to release this function.
Skipping a programme number
1. Select a programme number to be skipped with the PRxy
or VOLÏq button.
2. Press the CYAN button. The skipped programme turns to blue.
3. Press the CYAN button again to release the skipped programme.
Note: When a programme number is skipped it means that you will be unable to
select it using the PRxy button during normal TV viewing. If you want to
select the skipped programme, directly enter the programme number with the
NUMBER buttons or select it in the Programme Edit.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Control
You can adjust picture Contrast, Brightness, Colour, Sharpness and Tint(only in
NTSC mode) to the levels you prefer.
Picture
Manual Picture Control
Contrast
Brightness
Colour
90
75
75
60
1. Press the MENU button.
2. Select the Picture menu, then press VOLÏq.
3. Press the PRxy button select a picture item.
4. Press the VOLÏq button to adjust the picture
condition as you want.
Sharpness
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Adjustꢀ:ꢀ◀▶
5. Press the TV/AV button to store for the picture User.
Selected Item
Contrast
Setting Change
More darkness VOLÏ 0~100 qVOL More light
Less bright VOLÏ 0~100 qVOL More bright
Lower color intensity VOLÏ 0~100 qVOL Higher color intensity
Brightness
Colour
Sharpness
Tint*
Soft picture VOLÏ 0~100 qVOL Sharp picture
More purple VOLÏ -50~50 qVOL More green
Auto Picture Control
*The Picture options - Dynamic, Standard, Mild and Game
are programmed for good picture reproduction
at the factory and cannot be changed.
PSM (Picture Status Memory)
1. Press the PSM button.
2. Press the PSM button repeatedly to select [PSM].
Each press of the button changes the screen display as
below.
Dynamic → Standard → Mild → Game → User
• Dynamic : Vivid Picture Appearance
• Standard : Standard Picture Appearance
• Mild : Softer Picture Appearance
• Game : External Video Game Picture Setup
• User : Manual Picture Setup
Note. In PC mode, PSM function isn’t available.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Control
You can select your preferred sound setting; Flat, Music,
Movie or Speech. You can also adjust the sound
frequency of equalizer, balance. If you switch AVL to on,
the set automatically keeps on an equal volume level even
if you change programmes.
Sound
Equalizer
Balance
AVL
Surround
Sound Mode
▶
0
Off
Off
MONO
1. Press the MENU button.
2. Select the Sound menu, then press VOLÏq.
3. Press the PRxy button to select the desired
sound item; Equalizer, Balance, AVL, Surround or
Sound Mode.
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Nextꢀ:◀▶
4. Press the VOLÏq button to make desired
adjustment.
5. Press the VOLÏq button in Equalizer to set the
Equalizer.
Equalizer
Flat
Music
Movie
Speech
User
0.1 0.5 1.5ꢀ 5.0ꢀ10KHz
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
6. Press the PRxy button to select your preferred
setting ; Flat, Music, Movie, Speech or User.
To set the Equalizer User.
a. Select User by pressing the PRxy button.
b. Select a sound band by pressing the VOLÏq
button.
c. Make appropriate sound level with the PRxy
button.
d. Press the MENU button to return to preceding
menu.
7. Press the PRxy button to the Balance menu.
8. Select the Balance menu with the VOLÏq button
and adjust the balance of speaker.
9. Select the AVL(Automatic Volume Leveler) menu
ON or OFF.
10.Select the Surround menu On or Off.
11.Select the Sound Mode menu.
If the sound quality is poor while you are watching a programme broadcast in
Stereo, select MONO with the VOLÏq button. Press the VOLÏq button to
switch between MONO and STEREO.(Please note that it works only when the
broadcast is done in stereo).
If a programme is received in two language(dual language), you can switch to
DUALⅠ or DUALⅡ by pressing the VOLÏq button repeatedly.
DUALⅠ sends the primary broadcast language to the loudspeakers.
DUALⅡ sends the secondary broadcast language to the loudspeakers.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Control
Auto Sound Control
* The sound Flat, Music, Movie and Speech are
programmed for good sound reproduction at the factory
and cannot be changed.
SSM (Sound Status Memory)
1. Press the SSM button.
2. Press the SSM button repeatedly to select.
Each press of the button changes the screen display
as below.
Flat → Music → Movie → Speech → User
• Choose Flat for the standard factory settings.
• Choose Music when watching music video or
concerts.
• Choose Movie when watching movies.
• Choose Speech when watching a show that is
mostly dialogue.
• Choose User to recall your personalized settings.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Other functions
You can control other functions; Clock, Blue Back, Auto
Sleep, Childlock, Radio and ARC menu.
Special
Clock
▶
Off
Off
Off
Off
Blue Back
Auto Sleep
Childlock
Radio
Clock
Setting the clock is necessary in order to use the various
timer features of the TV. You can set automatic TV On or
Off time.
ARC
16:9
Positionꢀ:▲▼
Nextꢀ:◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
1. Press the MENU button.
2. Press the PRxy button to select the Special menu.
Then press the VOLÏq button.
3. Press the VOLÏq button to select Clock menu.
Clock
Clock
--:--
Off Time
On Time
On Programme
--:-- Off
--:-- Off
1
Positionꢀ:▲▼
Adjustꢀ:ꢀ◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
4. Setting the clock
Press VOLÏq, to select hour & minutes. Press PRxy to
select the number between 00:00 …23:59) (Hours:Minutes)
After setting the time, press VOLÏquntil the red letters
disappear.
5. OFF time
Select the OFF time by pressing PRxy. Press VOLÏq, to
select hour/minutes. Press PRxy to select the number
between 00:00 …23:59) (Hours:Minutes).
Select ON/OFF, to turn the OFF TIME On/Off
After setting the OFF time, press VOLÏq until the red
letters disappear..
6. ON TIME
Select the ON time by pressing PRxy. Press VOLÏq, to
select hour & minutes. Press PRxy to select the number
between 00:00 …23:59) (Hours:Minutes) .
Select ON/OFF, to turn the ON TIME On/Off
After setting the ON time, press VOLÏq until the red letters
disappear.
7. ON Programme
Select the ON Programme by pressing PRxy. Press
VOLÏq to change the programme number. This programme
number will be the first programme displayed after setting
the ON TIME.
8. Press the TV/AV button to return to normal TV viewing.
Note. The present time must be set for using the Clock function.
Blue Back
If no signal is being received or the signal is very weak, a blue screen automatically
replaces the noisy picture background.
If you wish to continue viewing the poor picture, you must select the Blue Back
Off.(Pressing the VOLÏq button will alternate between “On” and “Off”.)
SLEEP TIMER
Set the timer for the TV to turn off at the preset time automatically.
Press the SLEEP button on the remote control.
The number on the screen changes from
0-> 15->30->60->0
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Other functions
Auto Sleep
If you select Auto Sleep On the set will automatically switch
itself to standby mode approximately ten minutes after a TV
Channel stops broadcasting.
1. Press the MENU button.
2. Select the Special menu, then press VOLÏq.
3. Press the PRxy button to select Auto Sleep.
4. Press the VOLÏq button to select On.
5. Press the TV/AV button to return to normal TV viewing.
Childlock
Childlock menu is necessary in order to disable the buttons
on the side panel of the set. Especially it is useful to prevent
unauthorized viewing.
1. Press the PRxy button to select Childlock.
2. Press the VOLÏq button repeatedly to select On or Off.
* When the setting is Childlock On, the buttons on the side
panel of the set is disabled except ON/OFF button.
* When the setting is Childlock Off, the buttons on the side
panel of the set is enabled.
Radio
You can listen to radio with the set.
1. Press the MENU button.
2. Press the PRxy button to select the Special menu.
Then press the VOLÏq button.
3. Press the PRxy button to select Radio.
4. Press the VOLÏq button to select Radio On or Off.
Note. When the setting is On, you can adjust radio function in radio mode. (see page 20)
ARC (Aspect Ratio Control)
You can watch TV in various picture formats; Auto, 16:9, 14:9, 4:3, 16:9 Zoom, 14:9
Zoom, 4:3 Zoom.
Repeatedly press the ARC button to select your desired picture format.
Auto When your set receives the wide screen signal, it will change automatically the picture
format that has been sent.
16:9 You can enjoy the cinema or general TV programme through the 16:9 mode.
The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and
right so that the screen 16:9 is full.
14:9 You can enjoy the picture format of 14:9 or general TV programme through the 14:9 mode.
The screen 14:9 is viewed just like that the screen 4:3 is magnified to the upper/lower
and left/right.
4:3 This picture format is 4 to 3 of general TV.
16:9 Zoom Magnifies the size of the picture on screen 16:9.
14:9 Zoom Magnifies the size of the picture on screen 14:9.
4:3 Zoom Magnifies the size of the picture on screen 4:3.
Note. In Zoom mode, you can adjust the position of the picture with PRxy button.
(It’s possible when the ARC information is displayed on screen.)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Control
This function is possible only when the set is in Radio mode.(Radio mode is displayed
when the Setting for special menu is radio On.)
Radio Setup
1. Use TV/AV button on remote controller to select
Mode
Auto
87.5 MHz
1
Frequency
Programme
Memorize
Delete
Radio mode.
2. Press the MENU button to set Radio Setup menu.
3. Press the VOLÏq button repeatedly to select
Mode Auto or Manual.
Auto Programme
Off Time
Edit Name
Name
▶
Off
▶
--------
* When the Radio Setup Mode is Auto, only the
Positionꢀ:▲▼
Nextꢀ:◀▶
Exitꢀ:ꢀTV/AV
programmes stored in memory are selected.
*
When the Radio Setup Mode is Manual, all frequencies
are selected.
4. Press the PRxy button select Frequency.
Then press the VOLÏq button repeatedly to tune in the
desired station manually. If you press the VOLÏq button
continually above 2 seconds, It automatically changes
present frequency into next frequency.
5. Press the PRxy button to select Programme.
Then press the VOLÏq button repeatedly to select programme.
6. Press the PRxy button to select memorize. If you want
to memorize this radio setup, press the VOLÏq button.
7. Press the PRxy button to select Delete. Select Off
with the VOLÏq button to delete the station.
8. Press the PRxy button to select Auto Programme.
9. Press the VOLÏq button
Radio Auto Programme
repeatedly to automatically
scans and tunes to the next
available station.
Start
10. Press the PRxy button to
select Off Time. Then press the
VOLÏq button repeatedly to
Startꢀ:◀▶
select Off, 5, 10, 30(minutes).
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
The on-screen displays disappear
after time selected.(when you
select Off, the on-screen displays
will not disappear.)
Radio Name Edit
▲
Station
P01
--------
The displays identifies the
status of radio settings.
11. Press the PRxy button to
select Edit Name.
▼
Adjustꢀ:ꢀ▲▼◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
Confirm:ꢀOKꢀꢀ
Then press the VOLÏq
button to edit radio name.
12. You can assign a radio name with 8 characters.
Press the PRxy button repeatedly. You can use the
numeric 0 to 9, the alphabet A to z(capital and small letters.) and a blank.
With the VOLÏq button, you can select in the opposite direction.
13. Press the MENU button to return to prior menu.
14. Press the TV/AV button to exit. Then the radio setting condition is displayed.
Note. You can listen to the radio while you are at PC mode. Simply go to the PC mode,
and then press MENU, select the SOUND menu, and then change the INPUT
item to the RADIO.
Please ensure that the antenna is connected and the RADIO selection
is ON at the SPECIAL menu.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Other functions
Calling the programme list
You can check the programmes stored in the memory
by displaying the programme LIST.
Programme List
P00 -----
P01 -----
P02 -----
P03 -----
P04 -----
P05 -----
P06 -----
P07 -----
P08 -----
P09 -----
Displaying programme list
1. Press the LIST button to display the
Programme list menu.
Positionꢀ:▲▼◀▶
Confirmꢀ:ꢀOKꢀꢀ
Exitꢀ:ꢀTV/AV
The programme list appears on the screen.
One programme list contains ten programmes as right.
Note :
a. You may find some blue programmes.
They have been set up to be skipped by auto
programming or in the programme edit mode.
b. Some programmes with the channel number shown
in the programme
list indicate there is no station name assigned.
Selecting a programme in the programme list
Select a programme with the PRxy or VOLÏq button.
Then press the OK button.
The set switches to the chosen programme number.
Paging through a programme list
There are 10 programme table pages in which contain
100 programmes.
Pressing the PRxy or VOLÏq button repeatedly turns
the pages.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TELETEXT
TEXT On/Off
Press the TEXT/MIX button to switch to TELETEXT.
The initial page or last selected page appears on the screen.
The first page number indicates your selection,
while the second shows the current page displayed.
1. Press TEXT/MIX button once, displays the Teletext pages.
If you press the TEXT/MIX button twice, the teletext
pages and the TV picture are concurrently displayed
on both sides of the screen.
2. Press TEXT/MIX button once more, displays the
Teletext pages superimposed on the TV picture.
3. Press the TEXT/MIX button to switch off Teletext
once more, Text mode is off, and TV mode appears.
If you press the TEXT/MIX button displays are changed as below.
TEXT → MIX → Double window TEXT → TV mode
TOP text
The user guide displays four fields-red, green, yellow and
blue at the bottom of the screen. The yellow field denotes
the next group and the blue field indicates the next block.
Group/block/page selection
1. With the BLUE button you can progress from block to block.
2. Use the YELLOW button to proceed to the next
group with automatic overflow to the next block.
3. With the GREEN button you can proceed to the
next existing page with automatic overflow to the next group.
Alternatively the PRx button can be used.
4. The RED button permits to return to previous selection. Alternatively the PRy
button can be used.
FLOF text
The Teletext pages are colour coded along the bottom of the screen and are selected by
pressing the corresponding coloured button.
Page selection
1. Press the INDEX button to select the index page.
2. You can select the pages, which are colour coded along the bottom line with the
same coloured buttons.
3. The VOLÏq button can be used to select the preceding or following page.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TELETEXT
Special TELETEXT functions
MENU
Functions
Changes Teletext mode
Only Teletext mode, text mode superimposed on the
TV picture, TV mode
TEXT/MIX
Selects double height text.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of
the page.
SIZE
Press this button again to return to the normal display.
Stops the automatic page change, which will occur if a
Teletext page consists of 2 or more sub pages. The
number of sub pages and the sub page displayed is,
usually, shown on the screen below the time. When
this button is pressed the stop symbol is displayed at
the top left-hand corner of the screen and the
automatic page change is inhibited. To continue press
this button again.
HOLD
Return to index page
INDEX
Displays the TV picture on the screen while waiting for
the new Teletext page. The display will appear at the
top left hand corner of the screen. When the updated
page is available then display will change to the page
number.
UPDATE
Press this button to view the updated Teletext page.
When viewing a TV programme, press this button to
display the time at the top right hand corner of the
screen. Press this button again to remove the display.
The time will only be displayed at the channel that
broadcast the teletext. In Teletext mode press this
button to select and hold or change a four-digit sub
page number. This is displayed along the bottom of the
screen. Press this button again to exit this function.
TIME
Press this button to display the concealed information,
such as solutions of riddles or puzzles.
Press this button again to remove the information from
the display.
REVEAL
22
Download from Www.Somanuals.com. All Manuals Search And Download.
External Equipment Connection
You can connect additional equipment, such as VCRs, camcorders etc. to your set.
Examples are shown below.
Note. When connecting to other equipment, please ensure you turn the main switch
OFF to prevent any damage to the equipment.
Antenna connection
1. Connect RF out on the VCR to the
Antenna input on the rear of the TV.
2. Connect the antenna cable to the
antenna in jack on the VCR.
3. Use the TV/AV button to select TV mode.
4. Press the PLAY button on the VCR.
COMPONENT INPUT
1. device to the COMPONENT on the TV.
2. Use the TV/AV button to select
COMPONENT mode.
3. Press the PLAY button on the DVD.
DTV Input
1. Connect the DTV video
output sockets(Y,Pb, Pr)
of the DTV set top
box to the DTV
Input sockets of the set.
2. Connect the audio cable from the
DTV set top box to the Audio
Input sockets of the set.
3. Press the TV/AV button to select DTV mode.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
External Equipment Connection
Note.When connecting to other equipment, please ensure you turn the main switch
OFF to prevent any damage to the equipment.
A/V INPUT
1. Connect the A/V out jacks on of the VCR to
A/V-In jacks on the TV.
2. Press the TV/AV button to select VIDEO mode.
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If you have a mono VCR, connect the audio
cable from the VCR to the L(MONO) socket of the set.
A/V OUT
1. Connect the Audio outputs(L, R) of the TV to Audio-IN(L, R) of another displayer or
the amplifier system
- If you connect the amplifier system, you can also play the TV sound through
the stereo amplifier system.
2. Connect the Video output of the TV to Video IN of another displayer.
S-VIDEO input
If using an S-VIDEO source, the picture quality
will be improved over a video source.
1. Connect the S-VIDEO output of a VCR
to the S-VIDEO input on the TV.
2. Connect the audio cables from the
S-VIDEO VCR to the L (MONO) R inputs
on the TV.
3. Select S-VIDEO mode by pressing the
TV/AV button repeatedly.
4. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Headphone jack
Insert the headphone plug to the headphone jack on the TV. You can listen to sound
through the headphone; no sound from the speaker on the TV. To adjust the
headphone volume, use the( )Volume menu in the Sound menu.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the PC as a monitor
This function is possible only when the set is in PC mode.
Use the TV/AV button on remote controller.
MENU
Picture
Sound
H/V Position
Auto
q
q
q
Picture adjustment
You can adjust picture Contrast, Brightness,
Temperature, Clock, Phase and ARC as you prefer.
1. Press the TV/AV button to select the PC mode.
2. Press the MENU button.
Reset
1024 x 768 60Hz
Positionꢀ:▲▼
Nextꢀ:◀▶
Exitꢀ:ꢀTV/AV
3. Select the Picture, then press VOLÏq.
4. Press the PRxy button to select the desired
picture item.
5. Press the VOLÏq button to make appropriate
adjustments.
Picture
Contrast
Brightness
Temperature
Clock
60
80
6. Press the TV/AV button to exit menu.
9300K
50
Phase
ARC
34
16:9
Contrast
This function is to adjust picture to light/dark.
Positionꢀ:▲▼
Adjustꢀ:ꢀ◀▶
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Brightness
This function is to adjust brightness of picture.
Temperature
Temperature is a measure of the warmth of the image
color.
Clock
This function is to minimize any vertical bars or stripes
visible on the screen background. And the horizontal
screen size will also change.
Note : This mediation range is different according to
the supported resolution.
Phase
This function allows you to remove any horizontal
noise and clear or sharpen the image of characters.
ARC (Aspect Ratio Control)
Selects a screen mode.-4:3 or 16:9
* 4:3 mode : Sets the picture to 4:3 normal mode.
* 16:9 mode : Sets the picture to 16:9 wide mode.
4 : 3
16 : 9
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the PC as a monitor
Sound adjustment
1. Press the MENU button.
Sound
2. Select the Sound menu, then press VOLÏq.
Equalizer
Balance
AVL
Surround
Sound Mode
Input
q
0
Off
Off
L+R
PC
3. Press the PRxy button to select the desired
sound item; Equalizer, Balance, AVL, Surround or
Sound Mode.
4. Press the VOLÏq button to make desired adjustment.
5. Press the VOLÏq button in Equalizer to set the
Equalizer.
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀꢀExitꢀ:ꢀTV/AV
Nextꢀ:◀▶
6. Press the PRxy button to select your preferred
setting ; Flat, Music, Movie, Speech or User.
To set the Equalizer User.
Equalizer
Flat
Music
Movie
Speech
User
a. Select User by pressing the PRxy button.
b. Select a sound band by pressing the VOLÏq
button.
0.1 0.5 1.5ꢀ 5.0ꢀ10KHz
c. Make appropriate sound level with the PRxy
button.
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
d. Press the MENU button to return to preceding
menu.
7. Press the PRxy button to the Balance menu.
8. Select the Balance menu with the VOLÏq button and adjust the balance of speaker.
9. Select the AVL(Automatic Volume Leveler) menu ON or OFF.
10. Select the Surround menu ON or OFF.
11. Select the Sound Mode with PRxy button.
12. Press the VOLÏq button to select sound mode – L+R, L+L, R+R.
L+R : Audio signal from audio L input is sent to left loudspeaker and audio signal
from audio R input is sent to right loudspeaker.
L+L : Audio signal from audio L input is sent to left and right loudspeakers.
R+R : Audio signal from audio R input is sent to left and right loudspeakers.
13. Select the Input with PRxy button.
14. Press the VOLÏq button to select Input – PC, Radio.
In PIP mode, you can select PC or PIP Input.
Note:
a. When selecting radio mode, sound mode alternates between MONO and
STEREO according to the received signal.
b. In PC mode, radio mode supports only Auto.
c. In PC mode, radio control function is on an equality with Radio function in
the front.(See page 20)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the PC as a monitor
Position Adjustment
This function is to adjust picture to left/right and up/down
H/V Position
as you prefer.
1. Press the MENU button.
H-Position
V-Position
50
50
2. Select the H/V Position menu.
3. Press the PRxy button to select the desired
position item.
Positionꢀ:▲▼
Backꢀ:ꢀMENUꢀꢀꢀꢀꢀꢀꢀꢀ Exitꢀ:ꢀTV/AV
Adjustꢀ:ꢀ◀▶
4. Press the VOLÏq button to adjust horizontal
position and vertical position.
5. Press the TV/AV button to exit menu
Auto
This function is for the automatic adjustment of the screen position, clock and
clock phase. The displayed image will disappear for a few seconds while the
Auto-configuration is in process.
Note: Some signal from some graphics boards may not function properly.
If the results are unsatisfactory, adjust your monitor’s position, clock and clock
phase manually.
Reset
This function allows you to return to the good picture reproduction programmed
at the factory and cannot be changed.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the PC as a monitor
PC ANALOG(D-SUB) INPUT
1. Connect the PC ANALOG IN cable (D sub jack) from the monitor output socket
of the PC to the PC/DTV input socket of the set.
2. Connect the PC Audio IN cable from the PC to the PC Audio IN of the set.
3. Press the TV/AV or TV/PC button
to select PC ANALOG IN mode.
4. Switch on the PC, and the
PC screen appears on the set.
The set can be operated as the PC monitor.
DVI (Digital Visual Interface) INPUT
1. Connect the DVI of PC to the DVI input on the TV.
2. Select PC-Digital mode by pressing the TV/AV button repeatedly. (When
DVI source is connected, TV/AV mode converts PC to DVI mode.)
Resolution
Horizontal
Vertical
Mode
Resolution
frequency(KHz)
frequency(Hz)
640 x 480
640 x 480
640 x 480
720 x 400
31.5 KHz
37.9 KHz
37.5 KHz
31.4 KHz
60 Hz
72 Hz
75 Hz
70 Hz
VGA
800 x 600
800 x 600
800 x 600
800 x 600
35.1 KHz
37.9 KHz
48.1 KHz
46.9 KHz
56 Hz
60 Hz
72 Hz
75 Hz
SVGA
XGA
1024 x 768
1024 x 768
1024 x 768
48.4 KHz
56.5 KHz
60.0 KHz
60 Hz
70 Hz
75 Hz
1280 x 768
1280 x 768
47.4 KHz
47.8 KHz
60Hz RB
60 Hz
WXGA
DTV
720 x 576p
1280 x 720p
1920 x 1080i
31.2 KHz
37.5 KHz
28.1 KHz
50 Hz
50 Hz
50 Hz
Note:
a. If the set is cold, there may be a small “flicker” when the set is switched on.
This is normal, there is nothing wrong with the set.
b. Some dot defects may appear on the screen, like Red, Green or Blue spots.
However, this will have no impact or effect on the monitor performance.
c. The resolution which is not supported will appear at the resolution which gets near
to the resolution which is supported
* The standard of the resolution which gets near : H/V sync.
d. When resolutions are displayed that are not native to the panel resolution, text may
appear choppy or lines may appear to be bold or thicker than others.
To minimise, choose a resolution similar to the panel
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
Model
NLT-32W
Horizontal size 960(960) mm Thickness 109(222) mm
Main body
(With stand)
Height
513(565.5) mm Weight
17.6(19.3) kg
Television system
Television programme
LCD Panel
PAL-BG, I, DK / SECAM-BG, DK, / NTSC-M
VHF: 0~12 UHF :21~69 Cable : S1~S41
32" WIDE TFT LCD panel
WXGA (1366 x 768)
Resolution
Power consumption
150W
Stand by Power consumption Below 3W
External antenna impedance 75Ω
Audio output
10W + 10W
External input ports
• PC Digital IN • A/V IN • A/V OUT
• HEADPHONE OUT
• PC/DVI-AUDIO IN
• PC Analog IN
• COMPONENT IN • DTV IN
• S-VIDEO IN • ANTENNA IN
AC Input
100-240Va.c. 50/60Hz
19.3 kg
Net Weight
Gross Weight
25.43 kg
Note.
a. Although LCD panel uses highly precise technology, it may display blank pixels, dark spots,
or lightning pixels on the screen. This is normal and not an indication of a defect
b. Technical specifications are subject to change without notice
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check item
• Insert the AC power cord plug securely in AC power
outlet.
• Make sure the set is not in the standby mode
(The POWER/Standby indicator is red.)
No picture on screen and no sound
from speakers
• Check the brightness setting of the display.
• Lamp may have malfunction.
No picture/No picture from AV
terminal
• Check the sound setting.
• Make sure the sound is not muted.
• Make sure a pair of headphones is not connected.
• Make sure the connectors of the optional speaker
system are securely inserted.
Picture is displayed, but no sound
from the speakers.
• Make sure COLOR and CONTRAST settings.
Picture is too light
Picture is too dark.
• Make sure BRIGHTNESS setting is not set too low.
• Lamp may have malfunction.
• Change the batteries.
• Make sure the infrared transmitter window is not
receiving strong light such as light from fluorescent
lamps.
Remote control does not work.
•The reception may be weak.
• The state of the broadcast may also be bad.
• Make sure the antenna is facing the right direction.
• Make sure the outside antenna is not disconnected.
The picture is not sharp.
The picture moves.
• Make sure the antenna is facing the right direction.
• There may be reflected electric waves from
mountains or buildings.
The picture is doubled or tripled.
The picture is spotted.
• There may be interference from automobiles, trains,
high voltage lines, neon lights, etc.
• There may be interference between the antenna cable
and power cable. Try positioning them further apart.
• Is the unit receiving interference from other devices?
Transmission antennas of radio broadcasting stations
and transmission antennas of amateur radios and
cellular phones may also cause interference.
• Use the unit as far apart as possible from devices
that may cause possible interference.
There are stripes on the screen or
colors fade.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
NEC Australia Pty. Ltd.
ABN 86 001 217 527
Home Electronics Group
NEC Service Centres
New South Wales
Sydney
184 Milperra Rd, Revesby 2212
131-632
131-632
Newcastle 120 Parry Street, Newcastle West 2302
Victoria
Melbourne Unit1/6, Garden Road, Clayton, 3168
131-632
Queensland
Brisbane
Unit 4/305 Montague Road, West End, 4101
131-632
131-632
Southport Shop 1, 48 Ferry Road, Southport 4215
South Adelaide
Adelaide
84A Richmond Rd, Keswick, 5053
131-632
131-632
Western Australia
Perth 45 Sarich Court, Osbome Park 6017
For Service in outer areas, please contact your NEC retailer for the
address of the nearest Authorised NEC Service Centre
NEC Australia Pty. Ltd.
Home Electronics Group
244 Beecroft Road EPPING 2121
Tel:131-632
Fax:(02) 9877 2353
31
Download from Www.Somanuals.com. All Manuals Search And Download.
500-011H050729
Download from Www.Somanuals.com. All Manuals Search And Download.
|