MB QUART Car Speaker PVL216 User Manual

www.mbquart.com  
PREMIUM  
PVL216 / PVL268 / PVL269  
Thank you for choosing MB Quart Premium speakers for your car audio sound  
system. With proper installation, you are on the path to experiencing your music in  
a way you only imagined possible. Here at MB Quart, we call this Sound In Every  
Detail.”  
The Premium series speakers have been designed for the enthusiast looking for  
incredible sound and amazing performance. The Premium series speakers feature  
the following:  
- Convertible Coax/Component Capability  
- 40mm Silk Dome Tweeter  
- Gold Plated Speaker Terminals  
- Active Crossover With Variable Tweeter Attenuation  
And Gold Plated Terminals  
- Edge Rolled Steel Basket  
- Spider Woven Tinsel Leads  
- Motor Damping Magnet Cap  
- Progressive Long Travel Spider  
- Progressive Grill  
- High Energy Magnet  
- Polypropylene Cone  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PVL216  
7.24”  
5.61”  
70  
70  
70  
140  
140  
140  
4
4
4
87  
38 - 32,000  
87  
87  
38 - 32,000  
38 - 32,000  
40mm  
16cm  
40mm / 1.58”  
40mm / 1.58”  
16cm / 6.5”  
16cm / 6.5”  
2 X-Overs  
140  
4
70  
70  
140  
4
70  
140  
87  
38 - 32,000  
87  
38 - 32,000  
87  
38 - 32,000  
40mm  
16cm  
40mm  
16cm  
40mm  
16cm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PVL268  
8.05”  
7.36”  
5.81”  
5.11”  
40  
80  
4
40  
80  
40  
80  
4
4
87  
38 - 32,000  
87  
87  
38 - 32,000  
38 - 32,000  
40mm  
5x7” / 6x8”  
40mm / 1.58”  
5x7” / 6x8”  
40mm / 1.58”  
5x7” / 6x8”  
2 X-Overs  
80  
40  
40  
80  
80  
4
40  
4
87  
87  
38 - 32,000  
38 - 32,000  
87  
38 - 32,000  
40mm  
5x7” / 6x8”  
40mm  
5x7” / 6x8”  
40mm  
5x7” / 6x8”  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PVL269  
8.05”  
7.36”  
5.81”  
5.11”  
50  
110  
4
50  
110  
50  
110  
4
4
88  
32 - 32,000  
88  
88  
32 - 32,000  
32 - 32,000  
40mm  
6x9”  
40mm / 1.58”  
6x9”  
40mm / 1.58”  
6x9”  
2 X-Overs  
110  
50  
50  
110  
4
50  
110  
4
88  
88  
32 - 32,000  
32 - 32,000  
88  
32 - 32,000  
40mm  
6x9”  
40mm  
6x9”  
40mm  
6x9”  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREMIUM  
PVL216 / PVL268 / PVL269  
We strongly recommend that you have your new Premium series speakers installed by your authorized  
MB Quart dealer. The installation professionals employed by your dealer have the necessary tools and  
experience to disassemble your vehicle, install your new speakers and reassemble everything properly.  
If you prefer to perform your own installation, it is very important that you read the entire manual first.  
GETTING STARTED:  
- Turn off the audio system.  
- Check clearance on both sides of mounting surface to ensure that there are no obstructions  
(windows, tracks, wiring etc).  
CROSSOVER NETWORK INSTALLATION:  
- Locate a dry location for mounting of your Premium Crossover Networks. DO NOT MOUNT IN DOORS!  
- Remove the cover of the crossover by squeezing either side. This exposes the mounting holes for securing  
the crossover to a flat surface. Prior to pre-drilling pilot holes, ensure that you will not be drilling into wiring,  
gas tanks, fuel lines etc.  
- Once the crossover is mounted, snap the protective cover back in place.  
INPUT  
MID BASS  
VARI-TWEETER  
IN+ IN- WF+ | WF- TW+ | -6dB | -3dB | 0dB  
|
WIRING THE PREMIUM CROSSOVER  
INPUT  
IN+: Connect positive speaker wire from radio or amplifier.  
IN-: Connect negative speaker wire from radio or amplifier.  
MID BASS  
WF+: Provides positive output to midrange speaker.  
WF-: Provides negative output to midrange speaker.  
VARI-TWEETER  
TW+: Provides positive output to tweeter.  
-6dB: Provides negative output to tweeter at -6dB.  
-3dB: Provides negative output to tweeter at -3dB.  
0dB: Provides negative output to tweeter with no manipulation.  
The negative connection under the VARI-TWEETER section allows for varied degrees of tweeter attenuation.  
Only connect to one negative terminal with the understanding that 0dB is no manipulation and the loudest  
selection for tweeter output, -6dB is the quietist selection for tweeter output and -3dB is in the middle.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREMIUM  
PVL216 / PVL268 / PVL269  
Wiring Diagram  
INPUT  
|
MID BASS  
|
VARI-TWEETER  
WF- TW+ | -6dB | -3dB | 0dB  
IN+  
IN- WF+  
SELECTABLE  
CLIP INDICATOR  
AMBER-  
CLIP INDICATOR  
AMBER-  
GREEN-  
PRE CLIP  
SOFT CLIP  
RED-  
HARD CLIP  
GREEN-  
PRE CLIP  
SOFT CLIP  
RED-  
HARD CLIP  
LEVEL  
LEVEL  
9V  
0.2V  
9V  
0.2V  
BASS BOOST  
BASS BOOST  
0dB  
12dB  
0dB  
12dB  
BASS FREQUENCY  
MULTIPLIER  
FREQUENCY  
30Hz  
80Hz  
X15  
X1  
HIGH PASS  
FILTER SLOPE  
6dB  
12dB  
15Hz  
1KHz  
CHANNELS 1&2  
HIGH PASS  
CHANNELS 3&4  
LOW PASS  
(x1) 20Hz  
(x15) 300Hz  
300Hz  
4.5KHz  
40Hz  
4.5KHz  
CROSSOVER  
CROSSOVER  
LP-BP LP-BP HP-FULL  
MONO STEREO  
DUPE  
(3&4)  
HP-FULL  
INPUT MODE  
PROTECT  
POWER  
4CH  
2CH  
-
+
VERY IMPORTANT  
TINSEL TO  
MID BASS  
NO TINSEL  
WIRE  
CONNECT “WF” WIRE FROM  
CROSSOVER TO THE SPADE  
OR SCREW DOWN TERMINAL  
WITH TINSEL WIRE TO  
MID BASS  
IF THE TWEETER IS MOUNTED AS  
A COAXIAL IN THE CENTER OF  
THE MID BASS, CONNECT THE  
WIRE FROM THE TWEETER TO  
THE SCREW CLAMP WITHOUT  
TINSEL WIRE. THEN CONNECT  
“TW” WIRE FROM CROSSOVER  
TO THE SPADE OR SCREW  
(The above illustration shows the positive terminal view.  
The negative terminals are opposite.  
Be sure to identify the tinsel wire for your mid bass.)  
DOWN WITHOUT TINSEL WIRE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREMIUM  
PVL216 / PVL268 / PVL269  
Tweeter Mounting Options Separate From Mid Bass (Component)  
Flush Mount Method  
Top Mounted Method  
Mounting Surface  
Mounting Brackets  
Cup Mounting Screws  
Mounting Bracket Washers  
Mounting Bracket Screws  
Mounting Surface  
Surface Angle Mount Method  
Cup Mounting Screws  
Mounting Surface  
Tweeter Mounting In The Center Of The Mid Bass (Coaxial)  
Guide Pin  
Grille  
Indents  
Tweeter Assembly  
Wires  
Tweeter Post  
Assembly  
Bottom View Of  
Tweeter Assembly  
Tweeter Post  
Guide Pins  
1. Place the tweeter grille onto the  
tweeter assembly to prevent  
damage to the delicate silk dome  
2. Route the red & black tweeter  
wires through the opening in the  
top of the tweeter assembly  
3. Line up the 4 guide pins on the  
tweeter post with the 4 indents  
on the bottom of the tweeter  
assembly  
4. Fasten the tweeter post to the  
tweeter assembly using the  
provided screw and lock washer  
Lock Washer  
Screw  
Phase Plug  
1. Un-screw the phase plug by turning  
counter-clockwise and remove  
2. Route the tweeter wires through the  
center of the speaker until they come  
out the back of the speaker  
3. Screw the tweeter post assembly  
clockwise until snug  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREMIUM  
PVL216 / PVL268 / PVL269  
Speaker, Tweeter and Crossover Placement Options:  
Factory sound systems vary greatly. Some systems have coaxials (tweeter fixed in the center of the midrange) in the  
door, while others have factory component (tweeter is separate from midrange) systems. If your system has the factory  
component offering then you will want to locate your factory tweeter mounting location and compare it to the diagram  
below. Some vehicles already have the tweeter in the ideal location, while others often position the tweeter in the top  
corner of the door pane which is less than ideal. A good rule of thumb is to try and mount the tweeter within 8 inches  
of the midrange woofer for optimal imaging and tonal balance. When selecting an optimal mounting location, ensure  
that you are clear of any obstructions within the door. Cutting or drilling into moving parts or electrical accessory wires  
can be very dangerous and costly.  
Woofers should typically be installed in the factory locations. Simply ensure that the new woofer will not obstruct the  
window or other moving parts in the door.  
The Crossover should NEVER be mounted in the shell of the door. This can damage the crossover through vibration  
and moisture which is NOT covered under warranty. The Crossover can be mounted in a kick panel, under a seat or in  
the trunk as long as the area is not located near any moving parts in the vehicle which could cut or pull the wires  
resulting in a short circuit.  
All wiring to and from the crossover should avoid all moving parts in the vehicle which could potentially damage the  
wiring. Take great care when running wires through the door frame and into the door as wires can easily be cut. A  
rubber grommet should be used on both holes and wire loom should be wrapped around the exposed wires as shown  
in the diagram below.  
Alternate Tweeter  
Location  
Crossover  
Ideal Tweeter  
Location  
Route speaker wires  
through rubber grommet  
between door jam and  
door as shown. Use wire  
Mid Bass  
loom to protect the wires.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
www.mbquart.com  
PREMIUM  
PVL216 / PVL268 / PVL269  
car audio  
PART#U1010  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Tiller rta12 User Manual
Linksys Network Cables EG1032 V3 User Manual
LST Smoke Alarm 2351E User Manual
Makita Cordless Saw BJV140 User Manual
Makita Portable Generator G12000R User Manual
Maytag Dishwasher 6 915513 A User Manual
McCulloch Lawn Mower 96141004402 User Manual
Melissa Hair Dryer 235 019 User Manual
Metabo Plumbing Product TDP 7500 S User Manual
Microsoft Window A2xx User Manual