MODELS: 9270-02-01
GX270 HONDA
9270-03-01
EX270 SUBARU
9390-02-01
GX390 HONDA
9400-03-01
EX400 SUBARU
9570-04-01
570 VANGUARD
Owners Manual and Safety Instructions for
OPTIMAX BLOWER
Download from Www.Somanuals.com. All Manuals Search And Download.
LITTLE
WONDER
BLOWER
IMPORTANT MESSAGE
On behalf of everyone at Little Wonder, we would like to thank you for your purchase of a Little Wonder Gasoline
Powered Optimax Blower. This professional blower was designed to the highest standards to ensure you many
hours of uninterrupted service.
This manual provides the information necessary for safe and efficient operation and service. For your safety, it
is critically important that you read and understand this entire manual before operating your blower.
LITTLE WONDER
SCHILLER GROUNDS CARE, INC.
1028 STREET ROAD, P.O. BOX 38
SOUTHAMPTON, PA 18966
TABLE OF CONTENTS
FIGURES
PAGE
SAFETY.........................................................................................................................................................4-8
SET UP INSTRUCTIONS............................................................................................................................9-10
CONTROLS.................................................................................................................................................... 11
OPERATION / MAINTENANCE .....................................................................................................................12
ADJUSTMENTS.............................................................................................................................................13
STORAGE / TORQUE SPECIFICATIONS.....................................................................................................14
INTAKE GUARD ASSY ....................................... FIGURE 1 .........................................................................15
ENGINE ASSY .................................................... FIGURE 2 .........................................................................16
HOUSING ASSY ................................................. FIGURE 3 .........................................................................17
WARRANTY............................................................................................................................... BACK COVER
MANY USES:
The extreme versatility offered by Little Wonder’s line of blowers makes them ideally suited for a wide variety
of jobs; blowing leaves, grass clippings, thatch, blowing tennis courts dry, cleaning large driveways, stadiums,
parking lots and other hard surfaces, precleaning roofs before repair and countless other jobs.
This Operator’s Manual is part of the machine. Suppliers of both new and second-
hand machines must make sure that this manual is provided with the machine.
4-2011
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
LITTLE
WONDER
BLOWER
This symbol means:
NOTICE !!!
ATTENTION!
BECOME ALERT!
Unauthorized modifications may present extreme
safety hazards to operators and bystanders and
could also result in product damage.
Your safety and the safety of others is involved.
Schiller Grounds Care, Inc. strongly warns against,
rejects and disclaims any modifications, add-on
accessories or product alterations that are not
designed,developed,testedandapprovedbySchiller
Grounds Care, Inc. Engineering Department. Any
Schiller Grounds Care, Inc. product that is altered,
modified or changed in any manner not specifically
authorized after original manufacture-including the
additionof“after-market”accessoriesorcomponent
parts not specifically approved by Schiller Grounds
Care, Inc.-will result in the Schiller Grounds Care,
Inc. Warranty being voided.
Signal word definitions:
The signal words below are used to identify levels
of hazard seriousness. These words appear in this
manual and on the safety labels attached to Schiller
Grounds Care, Inc. machines. For your safety and
the safety of others, read and follow the information
given with these signal words and/or the symbol
shown above.
DANGER indicates an imminently hazardous
situation which, if not avoided, WILL result in death
or serious injury.
Any and all liability for personal injury and/or
property damage caused by any unauthorized
modifications, add-on accessories or products not
approved by Schiller Grounds Care, Inc. will be
considered the responsibility of the individual(s) or
company designing and/or making such changes.
Schiller Grounds Care, Inc. will vigorously pursue
full indemnification and costs from any party
responsibleforsuchunauthorizedpost-manufacture
modifications and/or accessories should personal
injury and/or property damage result.
WARNING indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
CAUTIONindicatesapotentiallyhazardoussituation
which,ifnotavoided,MAY resultinminorormoderate
injury. It may also be used to alert against unsafe
practices or property damage.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, MAY result in property damage.
MODEL NUMBER: This number appears on
sales literature, technical manuals and price lists.
Schiller Grounds Care, Inc.
1028 Street Road
SERIAL NUMBER: This number appears only
on your unit. It contains the model number fol-
lowed consecutively by the serial number. Use
this number when ordering parts or seeking war-
ranty information.
Southampton, PA 18966 U.S.A
Phone: 215-357-5110
Fax:
215-357-8045
MODEL NUMBER
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
LITTLE
WONDER
BLOWER
MACHINE PREPARATION
Operator preparation and training
SITE PREPARATION AND CIRCUMSTANCES
Read the Operation & Safety
Manual
–
Evaluate the terrain to determine how to safely
perform the job. Only use accessories and
attachments approved by the manufacturer.
–
If an operator or mechanic
cannot read English, it is
the owner's responsibility
to explain this material to
them. If any portion of
this material is unclear,
contact your factory
–
Be sure the area is clear of pets and people,
especially young children. Never assume they
will remain where you last saw them. Stop the
machine if any enter the area.
representative for clarification.
–
Become familiar with the safe operation of the
equipment, operator controls and safety signs.
Be prepared to stop the engine quickly in an
emergency. Do not operate or allow another
person to operate this machine if there are any
questions about safety.
MULTIPLE OPERATORS
–
Keep a safe distance between operators when
working together.
MACHINE PREPARATION
–
Do not tamper with or defeat safety devices.
Keep guards, shields and interlock safety devices
in place and in proper working condition. They
are for your protection.
–
–
All operators and mechanics should be trained.
The owner is responsible for training the users.
Wear appropriate clothing, including safety
goggles or safety glasses with side shields when
operating. Wear substantial footwear. Do not
operate barefoot or wearing open sandals. Long
hair, loose clothing or jewelry may get tangled in
moving parts.
–
–
Keep all fasteners such as nuts, bolts and pins
well secured.
Verify that machine and attachments, if any, are
in good operating condition.
–
_
–
–
Wear appropriate hearing protection.
Wear dust mask to avoid breathing dust.
Wear safety glasses.
Never allow children, unskilled or improperly
trained people to operate this equipment. Local
regulations can restrict the age of the operator.
–
–
–
Keep warning labels and this operator's manual
legible and intact. Replacement labels and
manuals are available from the factory.
Do not operate machine while under the
influence of drugs or alcohol, or any other
condition of impairment.
The owner/user can prevent and is responsible
for accidents or injuries occurring to themselves,
other people or property.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
LITTLE
WONDER
BLOWER
OPERATING SAFELY
INTERRUPTING OPERATION
IN GENERAL
-
Before leaving the operator's position:
–
–
–
Use extra care when loading or unloading the
machine into a trailer or truck.
- Park on level ground.
- Shut off the engine.
Do not run the engine in an enclosed area where
dangerous carbon monoxide fumes can collect.
-
Stop the engine, and wait until the fan stops
moving:
- before refueling;
Never leave a running machine unattended.
Always stop engine when leaving the operator
position.
-
Stop the engine, and disconnect the spark plug
wire(s):
- before clearing blockages;
- before checking, cleaning or working on the
machine;
- if the machine begins to vibrate abnormally:
shut off machine immediately. Inspect
and have repairs made as needed before
restarting;
–
Do not blow towards people, cars, windows, or
other items which could be injured or damaged
by the blown debris.
–
Keep hands away from the blower air intake and
outlet.
STARTING
–
Start according to instructions in this manual or
on the machine.
- except for repairs or adjustments as specifically
noted, such as for carburetor adjustment,
where the engine must be running. Keep
hands and feet clear of moving parts in these
circumstances.
–
Do not change engine governor settings or
overspeed the engine. Operating the engine
at excessive speed can increase the hazard of
personal injury.
-
Allow the fan to come to a complete stop when
stopping operation to clear blockages, unclog,
inspect the machine, do maintenance or repair.
OPERATING ON SLOPES
-
Reduce the throttle setting during engine shut-
down and, if the engine is provided with a shut-
off valve, turn the fuel off at the conclusion of
operation.
USEEXTRACAREWHENOPERATINGONSLOPES.
EVALUATE THE RISKS INVOLVED BEFORE OPER-
ATING ON A SLOPE
.
-
Slopes are a major factor related to slip and fall
accidents that sometimes lead to severe injury or
death. All slopes require extra caution.
-
Do not operate on slopes if uneasy or uncertain.
Ultimate responsibility for safe operation on slopes
rests with the operator.
-
Do not operate on steep slopes. Poor footing could
cause a slip and fall accident.
-
Keep all movement on slopes slow and gradual.
-
Do not operate near drop-offs, ditches or embank-
ments. You could lose your footing or balance.
-
Do not turn on slopes unless necessary, and then
turn slowly and downhill when possible.
-
-
Be sure of your footing on slopes.
Watch for holes, ruts, bumps, rocks and other hid-
den objects. Uneven terrain could cause a slip and
fall accident. Tall grass can hide objects.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
LITTLE
WONDER
BLOWER
MAINTENANCE SAFETY
In general
-
When refueling or checking fuel level:
- Stop the engine and allow to cool;
- Do not smoke;
- Refuel outdoors only;
- Use a funnel;
-
Maintain machine according to manufacturer's
schedule and instructions for maximum safety
and best results.
- Do not overfill;
-
-
Park machine on level ground.
- If fuel is spilled, do not attempt to start the
engine until the spill is cleaned up and vapors
have cleared.
Never allow untrained personnel to service ma-
chine.
- Replace caps on fuel containers and tanks
securely.
-
Guards should only be removed by a qualified
technician for maintenance or service.
Sparks from static electricity can start fires or
cause explosions. Flowing fuel can generate static
electricity. To prevent static electricity sparks:
-
Adjust or repair only after the engine has been
stopped and the fan has stopped moving.
-
Disconnect spark plug wire(s) before doing any
maintenance.
-
Keep containers electrically grounded. Do not fill
containers in a vehicle or on a truck or trailer bed
with a plastic liner. Fill containers on the ground
away from the vehicle.
-
Replace parts if worn, damaged or faulty.
For best results, always replace with parts
recommended by the manufacturer.
-
When practical, remove petrol (gasoline)
powered equipment from the truck or trailer
and refuel it on the ground. If equipment must
be refueled on the truck or trailer, refuel from
a portable container rather than a dispenser
nozzle.
-
Do not dismantle the machine without releasing
or restraining forces which may cause parts to
move suddenly.
-
-
Provide adequate support, e.g. jack stands for
lifted machine or parts if working beneath.
-
-
Keep the dispenser nozzle in contact with the rim
of the fuel tank or container opening until fueling
is complete. Do not use a nozzle lock-open
device.
Do not put hands or feet near or under rotating
parts.
-
-
-
Clean up spilled oil or fuel thoroughly.
Replace faulty mufflers.
If fuel is spilled on clothing change it immediately.
To reduce fire hazards, keep the engine, muf-
fler, and fuel storage area free of grass, leaves,
debris buildup or grease.
STORAGE SAFETY
-
-
-
Stop the engine and allow to cool before storing.
Drain the fuel tank outdoors only.
Fans
Do not straighten or weld fans. Replace dam-
aged or failed fans..
Store fuel in an approved container in a cool, dry
place.
Fuel
-
-
Keep the machine and fuel containers in a locked
storage place to prevent tampering and to keep
children from playing with them.
WARNING
-
-
Gasoline (petrol)) and die-
sel fuels are flammable;
gasoline (petrol) vapors
are explosive. Use extra
care when handling.
Do not store the machine or fuel container near an
open flame, spark, or appliance, such as a water
heater, or a pilot light.
Store only in containers
specifically designed for
fuel.
-
-
Keep petrol (gasoline) storage area free of grass,
leaves and excessive grease to reduce fire haz-
ard.
Clean grass and debris from cutting units, drives,
mufflers and engine to help prevent fires.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
LITTLE
WONDER
BLOWER
SAFETY DECALS
An important part of the safety system incorporated in this blower are the warning labels found on the blower.
Replace labels if damaged or illegible.
ADVERTENCIA
Antes de comenzar:
WARNING
-Lea y entienda el manual del
operador y las etiquetas.
-Pide que alguien lea y explique el
manual y las etiquetas a usted si
usted no lee Inglés.
BEFORE STARTING:
-Use protección ocular y auditiva.
-Read and understand Operator
-No haga funcionar sin los
manual and labels.
-Wear hearing and eye protection.
protectores en su lugar.
-Pare el motor antes de dar servicio
-Replace labels and Operator
-La gente a más durante la
manual if lost or damaged.
operación.
4165977
DANGER
Fan blades can cut/crush.
-Keep hands and feet away.
-Stop engine and remove spark plug
wire before servicing.
D
-Do not operate without guards in
E
place.
F
L
E
C
WARNING
T
O
R
Thrown objects
-Keep bystanders away.
-Do not blow toward people or pets.
-Do not blow toward items that may
4165913
be damaged by flying debris.
4165913 USED ON REMOTE
HORIZONTAL DEFLECTOR MODELS
ONLY
4165975
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SET-UP INSTRUCTIONS
LITTLE
WONDER
BLOWER
SET-UP INSTRUCTIONS
1. Open box. Remove upper handle and cardboard
insert.
2. Lay box down with blower housing up. Use lower
handle to roll unit out of the box.
3. Locate hardware package.
4. Install upper handle to lower handle with (4) 3/8-16
x 1-34 carriage bolts and (4) 3/8-16 flanged nylon
insert nuts from the hardware package. Tighten the
nuts securely but not so much as to crush the tube.
(Figure 1)
FIGURE 1
5. Route the throttle cable in front of lower handle
crossbar. Install to the left side of the upper handle
with (2) 10-32 x ½ thread forming screws from the
hardware package. (Figure 2)
6. Ensure the center link of the chain is on the center
tooth of the deflector sprocket before connecting the
deflector cable. (Figure 5)
FIGURE 2
FIGURE 5
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SET-UP INSTRUCTIONS
LITTLE
WONDER
BLOWER
SET-UP INSTRUCTIONS (continued)
7. Route the deflector cable above the axle and in
front of the lower handle cross bar. Remove one of
the nuts and the boot from the end of the deflector
cable and install the cable through the key slot into
the bracket on the upper handle. Reconnect the
clevis from the control lever and install over the end
of the cable. Reconnect the clevis to the control
lever with a ¼ x 5/8 clevis pin and hairpin cotter.
(Note: The deflector can be moved and held in
place with the locking knob to help connect the
clevis fitting to the control lever. Move the control
lever to the rear to more easily connect the cable.
Loosen the knob so the deflector moves freely after
the clevis is connected. (Figure 3)
8. Move the deflector control lever to the rear of the
slot. Adjust the jam nuts on the cable fitting so
the deflector is completely closed. Lock the nuts
against the bracket when the adjustment is correct.
FIGURE 3
9. Secure the throttle and deflector cables to the
handle tubes with cable ties from the hardware
package. Trim off excess. (Figure 4)
10.
Fill the engine with oil to the level indicated
on the dipstick. Fill the fuel tank with clean, fresh
regular grade unleaded gasoline.
FIGURE 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
LITTLE
WONDER
BLOWER
(BLOWER SHOWN WITH SUBARU EX40 ENGINE.
OTHER ENGINES ARE SIMILAR.)
SWITCH (A)
Move to the “OFF” position to stop the engine.
Move to the “ON” position before starting engine.
THROTTLE (B)
Controls engine speed and the amount of air
being blown.
CHOKE (C)
Move to the “CHOKE” position to apply the
choke. Move to the “RUN” position to remove
the choke.
FUEL SHUT OFF (D)
Move to the “OFF” position to shut off the fuel
whenever transporting the machine by trailer
or truck or during storage. Move to the “ON”
position before starting the engine.
REMOTE HORIZONTAL DEFLECTOR LEVER (E)
Move the lever forward to direct the flow of air
down. Move the lever back to direct the flow of
air up.
LOCKING KNOB (F)
Tighten the knob to lock the horizontal deflector
in the desired position. Loosen to allow the
deflector to be rotated with remote horizontal
deflector lever.
VERTICAL DEFLECTOR (G)
Rotate the deflector to direct air discharge
forward or to the side.
HORIZONTAL DEFLECTOR (H)
Directs air flow. Controlled by Remote Horizontal
Deflector Lever E. May be locked in place with
knob F.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION / MAINTENANCE
LITTLE
WONDER
BLOWER
BEFORE STARTING THE ENGINE
1. Read the Operator Manual and Engine Manual.
Become familiar with the controls, how each func-
tions, and what it operates.
MAINTENANCE INSTRUCTIONS
Stop engine and remove the spark plug wire before
performing any maintenance.
2. Check the engine oil level and add if necessary.
Keep blower air intake clear of debris for best
performance.
3 Fill the fuel tank with good quality, clean, unleaded
regular gasoline (petrol). Use a funnel to avoid
spilling.
Clear air discharge area of any debris accumulation.
Ensure machine has been shut off and fan is no
longer moving before clearing.
OPERATING INSTRUCTIONS
Air flow can be directed to the side or front by the
two-position vertical deflector. The front discharge
position is used to remove debris from along walls,
fences, etc. The side discharge position is used to
form windrows or piles. The horizontal deflector
directs air downward to “chisel” under wet, heavy
leaves and litter. Air velocity is regulated by the
throttle setting.
Keep all hardware tight.
Check oil level daily. Top off as needed.
Change engine oil after the first 5 hours of operation.
Then change as recommended by the engine
manufacturer.
1. Remove drain plug and drain oil while engine is
warm.
To reduce windrowing or to blow over an obstacle,
point deflector upward.
2. Replace drain plug, remove fill plug and
fill with new oil. See engine manual for oil
specifications.
To avoid blowing in an area, close deflector and
reduce throttle setting.
3. Start and run engine for 30 seconds. Stop
engine.
Slight changes in deflector position will have a big
effect on air flow. Experiment until you find the best
position for your needs.
4. Wait 30 seconds, then re-check oil level.
When clearing a yard or parking lot, a little time spent
planning how to blow it off can greatly reduce the
total clearing time.
5. Top off if necessary. See engine manual for
details.
To stop the engine, move the throttle control to the
slow position and switch the engine off.
Stop the engine when moving from work site to work
site. This will save fuel and prevent inadvertently
blowing debris where you don’t want to.
NOTE: When transporting the machine by truck or
trailer, close the fuel valve. This avoids the possibil-
ity of flooding should any dirt get under the carbure-
tor float needle. Leaving the valve open can allow
severe flooding which may ruin the engine by diluting
the oil.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
LITTLE
WONDER
BLOWER
DEFLECTOR LEVER
DEFLECTOR CHAIN
If the deflector door moves from the set position dur-
ing operation, tighten the deflector lever pivot bolt just
enough to keep the deflector in place. DO NOT over
tighten, the handle tube could crush.
The sprocket needs to be installed on the deflec-
tor as shown. The chain consists of 2 master links,
6 roller links, and 5 pin links. The middle pin link
should be over the center tooth of the sprocket.
(Figure 2)
If large amounts of adjustment are required, the
chain can be moved one pitch on the sprocket to
gain 1/2” of adjustment.
HORIZONTAL DEFLECTOR
Adjust the jam nuts on the cable conduit so the deflec-
tor door is completely closed when the deflector lever is
moved all the way forward. (Figure 1)
FIGURE 1
FIGURE 2
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE / TORQUE SPECIFICATIONS
LITTLE
WONDER
BLOWER
STORAGE
To put the equipment into service after an extended
period of storage.
To prevent possible explosion or ignition of vaporized
fuel, do not store equipment with fuel in tank or
carburetor in an enclosure with open flame (for example,
a furnace or water heater pilot).
1. Check for loose parts and tighten if necessary.
2. Fill the fuel tank and then check the engine oil
Before the equipment is put into storage for any
period exceeding 30 days.
level.
3. Start the engine and check for fuel leaks. Repair
1. Drain all fuel from the fuel tank and fuel lines.
any leaks before operating the unit.
2. Start the engine and run until all the fuel is used
from the carburetor float bowl and the engine
stops.
3. While the engine is still warm, drain the crankcase
oil and replace with the proper weight oil
corresponding to the season the equipment will be
next used.
4. Remove the spark plug and squirt a small amount
of engine oil into the cylinder. Slowly pull the
starter a few times to distribute oil in the cylinder
and reinstall the spark plug.
5. Top off if necessary. See engine manual for
details.
TORQUE SPECIFICATIONS
Min. Torque
Ft-lbs (In-lbs)
Max. Torque
Ft-lbs (In-lbs)
Location
Description
P/N
Housing to engine face
BLT-W LF 5/16-24 x 1-3/8
BLT 5/16-18 X 1-1/2
910517
22
19
28
25
Engine to deck
64262-009
BLT-HEX 7/16-20 x 1-3/4 GR8
(USED ON 9270 MODELS)
64123-253
64123-127
64123-267
Fan to Crankshaft
50
30
30
90
50
50
BLT-HEX 3/8-24X1-3/4 GR8
(USED ON 9390 AND 9400
MODELS)
BLT-HEX 3/8-24 X 2.5 GR 8
(USED ON 9570 MODELS)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
INTAKE GUARD ASSY
LITTLE
WONDER
BLOWER
FIGURE 1
2
1
4
7
9
10
4
8
3
11
5
6
7
9
11
10
8
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
4166183
4165218.7
64123-54
64268-02
64229-02
LABEL-INTAKE GUARD
ASSY-GUARD INTAKE
BLT-HEX 5/16-18X.75
NUT-FL NYLON LOCK 5/16-18
NUT 5/16-18
1
1
4
6
4
1
1
4165926.10
64123-253
INTAKE PANEL-CENTER
BLT-HEX 7/16-20 x 1-3/4 GR8
(USED ON 9270 MODELS)
BLT-HEX 3/8-24X1-3/4 GR8
(USED ON 9390 AND 9400 MODELS)
BLT-HEX 3/8-24 X 2.5 GR 8
(USED ON 9570 MODELS
64123-127
64123-267
8
4166730
4166731
4166722
WLDMT-FAN 7 BLADE 2.75
(USED ON 9270 MODELS)
WLDMT-FAN 9 BL
1
(USED ON 9390 AND 9400 MODELS)
WLDMT-FAN, 9BL 3.25
(USED ON 9570 MODELS
9
10
64164-13
4163427
KEY 1/4 X 2 SQ
PLUG-FAN 7/16 X 1
1
1
(USED ON 9270 MODELS)
PLUG-FAN 3/8 X 1.0
(USED ON 9390 AND 9400 MODELS)
PLUG-FAN 18 VAN
4163424
4166437
(USED ON 9570 MODELS)
11
4165169
4165170
SPACER-FAN .53
(USED ON 9270, 9390, & 9400 MODELS)
SPACER-FAN 1.24
1
(USED ON 9570 MODEL)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE ASSY
LITTLE
WONDER
BLOWER
FIGURE 2
4
6
25 23
28
24
5
27
32
24
23
10
31
8
26
33
7
16
9
8
16
16
19
21
16
3
9
15
30
19
29
16
18
19
11
17
1
16
20
12
12
2
20
14
13
11
1
22
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
64229-02
64141-6
4166074
LOCKNUT-NYL 5/16-18
NUT 5/16-18
ENG-HONDA GX270
6
4
1
8
9
4164632
64123-283
GRIP-1-1/4 X 14
2
2
1
2
2
2
1
1
6
1
1
6
4
4
4
1
2
1
1
2
1
4
4
1
1
1
BLT-HEX 1/4-20X1.75
CABLE-PRE DEFLECTOR
WHEEL-4.10/3.50 X 6
SNAP RING.625
SPACER-PDR MTL 35X1.0X.25
AXLE
10 4166615
11 4164204
(USED ON 9270-02 MODEL)
ENG-SUBARU EX27
(USED ON 9270-03 MODEL)
ENG-HONDA GX390
(USED ON 9390 MODEL)
ENG-SUBARU EX40
(USED ON 9400 MODEL)
4165990
4166075
4165993
4166420
1
1
1
1
12 64144-36
13 4164192-01
14 4164178
15 4164591.10
16 64163-55
17 4164588.7
18 4165895.10
19 64123-61
20 4164204-01
21 64268-02
22 64262-009
23 64229-01
24 4165854
25 4165855.7
26 4166457
27 64139-26
28 64188-65
29 64268-03
30 64018-5
HANDLE-LOWER
WASHER-5/16 FLAT
DECK-ENGINE,BLR LG
BRACE-LOWER HANDLE
BLT-HEX 5/16-18X1-3/4
BEARING-WHL
NUT-FL NYLON LOCK 5/16-18
BLT-FLGHD 5/16-18X1-1/2
NUT-NYLON LOCK 1/4-20
WASHER- UHMW PE
WASHER-ANTIROTATION
CLEVIS-CABLE
BLT-WLF 10-32 X 5/8
PIN CLEVIS 1/4X.62
NUT-FL NYLON LOCK 3/8-16
BLT-CRG 3/8-16X1-3/4
BLT-HEX 1/4-20X2-1/2
S-BRACKET,DEFLECTOR
COTTER-HAIRPIN .08X1.19
ENG-ENGINE-VANGUARD 18
(USED ON 9570 MODEL)
4
5
4166778
S-LEVER W/ GRIP
(INCLUDES ITEM 6)
1
4166170-01
CABLE-THROTTLE
(USED ON HONDA ENGINES)
1
1
1
4166170-02
(USED ON SUBARU ENGINES)
4166170-03
CABLE-THROTTLE
CABLE-THROTTLE
(USED ON VANGUARD ENGINES)
6
7
4165987
4166779
GRIP-GRIP-1/4X1X5 LEVER
S-HANDLE UPPER W/ GRIPS
(INCLUDES ITEM 8 QTY 2)
1
1
31 64123-98
32 4166780
33 64168-2
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOUSING ASSEMBLY
LITTLE
WONDER
BLOWER
FIGURE 3
35
36
3
2
18
5
21
37
9
15
20
1
19
20
4
16
17
13
14
23
28
12
8
22
11
29
32
30
33
26
6
24
7
34
25
27
8
31
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
64141-6
4166329
4166187
4165975
910517
64151-31
910130
8-18
NUT 5/16-18
S-HOUSING LG BLOWER
LABEL-BLOWER SIDE
LABEL-WARNING/DANGER
BLT-WLF 5/16-24 X 1-3/8
LOCKNUT-10-32
SPRING-DEFLECTOR
RING-RETAINING
LABEL-READ MANUAL
LABEL-LB400S, 9400 MODEL
LABEL-LB570V, 9570 MODEL
LABEL-LB270H, 9270-02 MODEL
LABEL-LB270S, 9270-03 MODEL
LABEL-LB390H, 9390 MODEL
3
1
1
1
4
2
1
3
1
1
18 4164205
19 900404
20 900405
WHEEL-4.10/3.50X4
SLEEVE-WHEEL
SPACER-FRT WHL BRKT
BEARING-WHEEL
BEARING-FL PLASTIC .31 ID
SPACER-ENG HOUSING
BLT-HEX 1/4-20 X 2-1/4
WSHR .328X.75X14 GA
PIVOT-DEFLECTOR,OUTER
LINK-MASTER #43
CABLE-PUSH,POST DFLCTR
CABLE-PUSH,PRE-DFLCTR
BEARING-SLEEVE
PIVOT-DEFLECTOR,INNER
KNOB-1/4 FEMALE
NUT-NYLON LOCK 1/4-20
CHAIN-DEFLECTOR
LABEL-SCROLL UPPER
LABEL-SCROLL MIDDLE
LABEL-SCROLL LOWER
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
21 4164204-01
22 38304-06
23 4166181
24 64123-288
25 64163-55
26 4166175
27 4165192
28 4166614
29 4166615
30 4166324
31 4166176
32 4166195
33 64229-01
34 4166618
35 4166184
36 4166185
37 4166186
4165977
10* 4166193
4166194
4166190
4166191
4166192
11
4166182.17 DEFLECTOR-SIDE
1
2
1
1
1
1
1
12 64197-008
13 910123.10
14 910132
15 64229-03
16 64123-252
17 4165178.7
BLT-TDFM 10-32X1/2
DEFLECTOR-INT
HANDLE-DEFLECTOR
NUT-NYLON LOCK 3/8-16
BLT-HEX 3/8-16 X 5-1/2
BRKT-FRT WHL
*NOT ILLUSTRATED
17
Download from Www.Somanuals.com. All Manuals Search And Download.
5 YEAR LIMITED SERVICE & WARRANTY POLICY
FOR GASOLINE POWERED
OPTIMAX BLOWERS
All Little Wonder Gasoline Powered OptiMax blowers are guaranteed against defects in
material and workmanship, under normal usage, for a period of FIVE YEARS from the
date of purchase, under the following terms:
Any Little Wonder Gasoline powered OptiMax blower or part found to be defective
within the warranty period is to be returned to any registered Little Wonder dealer.
Engines for all gasoline powered products are warranted separately by the engine
manufacturer. Therefore, there are no warranties made, expressed or implied, for
engines for gasoline power products by Little Wonder.
Transportation charges for parts and units submitted for replacement under this warranty
must be borne by the purchaser.
THIS WARRANTY covers manufacturing defects only and does not cover defects
resulting from misuse, abuse, negligence, improper handling, care or maintenance,
normal wear and tear or non-observance of operating, maintenance or installation
instructions, or accident, or if the product has been repaired or altered outside our factory
or authorized repair facility in any respect which affects its condition.
Little Wonder’s liability is limited to repair or replacement of the defective product or
part at our sole discretion. All other liabilities, in particular, liability for damages, including
without limitation consequential, special or incidental damages are excluded.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. NO EMPLOYEE, REPRESENTATIVE
OR DEALER IS AUTHORIZED TO CHANGE THIS WARRANTY IN ANY WAY OR TO
GRANT ANY OTHER WARRANTY..
LITTLE WONDER®
SCHILLER GROUNDS CARE, INC.
1028 STREET ROAD, P.O. BOX 38
SOUTHAMPTON, PA 18966
PHONE 877-596-6337 • FAX 215-357-8045
Specifications, descriptions, and illustrative material in this literature are as accurate as known
at the time of publication, but are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|