ETS Installation Guide
For ETS8PS, ETS16PS, ETS16PR, and ETS32PR
Multiport Device Servers
Part Number 900-401
Revision A April 2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Disclaimer and Revisions
This product has been designed to comply with the limits for a Class A digital
device pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against such interference when operating in a
commercial environment. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with this
guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
interference in which case the user, at his or her own expense, will be
required to take whatever measures may be required to correct the
interference.
Changes or modifications to this device not explicitly approved by Lantronix
will void the user's authority to operate this device.
Cet appareil doit se soumettre avec la section 15 des statuts et règlements
de FCC. Le fonctionnement est subjecté aux conditions suivantes:
(1)Cet appareil ne doit pas causer une interférence malfaisante.
(2) Cet appareil doît accepter n'importé quelle interférence reìue qui peut
causer une opération indésirable.
The information in this guide may change without notice. The manufacturer assumes
no responsibility for any errors that may appear in this guide.
Date Rev. Comments
4/05
A
Initial Document
ETS Installation Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
ETS Installation Guide
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
ETS Installation Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
6
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1: Introduction
The Lantronix ETS (ETS8PS, ETS16PS, ETS16PR, and ETS32PR) is a multi-port
device server providing shared network access to terminals, devices, console ports,
and printers for a variety of network protocols and operating systems. The ETS
supports the TCP/IP, IPX (NetWare), Local Area Transport (LAT), AppleTalk
(EtherTalk), and Microsoft LAN Manager protocols.
Note: In this manual, all ETS servers will be referred to as “the ETS” unless
a distinction needs to be made between models.
The ETS stores its executable software in Flash (rewritable) ROM, meaning that it
does not have to download software from a host each time it boots. Software must
only be downloaded when a new software version becomes available. See
Supported Serial Protocols
All ETS models support the RS-232/423 serial protocol.
RS-232
The RS-232 line interface standard is a single-ended peer-to-peer interface. Today's
personal computers typically have at least one RS-232 serial port. It is the most
common serial protocol used today.
RS-232 is used for connecting devices across short distances at speeds up to 230.4
kb/s. Faster speeds require shorter cabling to ensure error-free communication. The
maximum cable length at a given speed is determined by many factors, including the
immediate electrical environment and the quality of cable used, but is usually less
than 15 meters at high speeds.
RS-423
All of the ETS models support the RS-423 line interface standard. RS-423 devices
are interoperable with RS-232 devices. That is, RS-232 ports can receive data
reliably from RS-423 ports and vice-versa.
The main difference between RS-423 and RS-232 is that RS-423 employs lower
voltage signaling and differential receivers. RS-423 still uses single-ended
transmitters for compatibility with RS-232 receivers.
RS-423 is generally rated at higher speeds over longer cabling runs than RS-232.
Maximum data rates of 230.4 kb/s are possible on ETS-PR models, and 115.2 kb/s is
the maximum on ETS-P models.
ETS Installation Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
How to Use This Manual
2:Installation
Explains how to physically install the ETS.
3:Getting Started
4:Using the ETS
Explains the minimum configuration needed.
Explains some of the ways that you can use your ETS.
5:Printing on the ETS
6:NetWare Configuration
7:LAT Configuration
Chapters 5 through 9 cover protocol-specific setup
needed to install print queues and otherwise use the
ETS.
8:AppleTalk Configuration
9:DLC Configuration for LAN Manager
A:Contact Information
B:Troubleshooting
Appendices A through F provide supplementary
information.
C: Pinouts
D:Updating Software
E:Specifications
F:Frequently-Used Commands
G:Compliance and Warranty Information
Read chapters 2 through 4 in order, then proceed to the protocol-specific chapter that
relates to your network. Refer to F:Frequently-Used Commands as needed. The
Device Server Reference Manual, located on the CD-ROM and web site, provides
additional information about configuring and using your ETS.
8
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Installation
This chapter describes the various ETS models and shows how to install them into a
basic network configuration. The ETSPS models will be explained first. For ETSPR
descriptions and installation instructions, skip to ETSPR Product Descriptions.
ETSP Product Descriptions
ETSPS Front Panels
The front panel of all ETSP models has a Test/Reset button (called Reset on the
ETS8PS and ETS16PS), seven LEDs, and a power switch. Pressing the Reset
button for 5 seconds while the unit powers up will flush the NVR (factory reset).
ETS8PS/ETS16PS LEDs
The seven LEDs are explained in the following table.
Table 2-1. ETS8PS/ETS16PS LED Functionality
LED
PWR
LNK
Function
Lights to indicate the ETS has power
Lights to indicate a functional 10BASE-T
network link
POL
OK
Lights to indicate a swapped 10BASE-T cable
Blinks to indicate that the ETS is functioning
properly
NET
RCV
Blinks to indicate Ethernet activity
Blinks periodically to indicate serial characters
entering the ETS
XMT
Blinks periodically to indicate serial characters
exiting the ETS
ETS8PS Back Panel
The back panel of the ETS8PS has a power plug, an AUI Ethernet port, an RJ45
10BASE-T Ethernet port, and eight RJ45 serial ports.
ETS Installation Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Figure 2-1. ETS8PS and ETS16PS Back Panels
ETS16PS Back Panel
The back panel of the ETS16PS has a power plug, an AUI Ethernet port, a 10BASE-
T Ethernet port, and 16 RJ45 serial ports.
Figure 2-2. ETS16PS Back Panel
Installing the ETSP
The following two diagrams show properly-installed ETSP servers.
Figure 2-3. Sample ETS8P/ETS16PS Network Layout (ETS8PS shown)
10
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
To install the ETS, complete the following steps in order. Refer to the numbers in the
previous figure.
1. Select a location for the ETS.
When choosing a location, keep in mind the environmental restrictions discussed
in E:Specifications.
2. Connect one or more serial devices to the ETS.
Note: The default serial port settings are 9600 baud, 8 bit characters, no
parity, 1 stop bit, and Xon-Xoff flow control. See C:Pinouts for
information on what kinds of device attachments the ETS supports.
3. It is recommended to connect a terminal to the ETS console port (port 1). This
will enable you to receive diagnostic and initial configuration messages.
4. Connect an Ethernet cable to either the 10BASE-T port (shown) or a transceiver
connected to the AUI port.
Note: The ETS will boot without a valid Ethernet connection, but it will
pause to print a message (seen on the console port) asking if you want
to stop at the Boot> prompt. If you do not respond to this message, it will
wait for 10 seconds and then finish booting.
5. Attach one end of the power cable to the ETS and plug the other end into an
electrical outlet.
6. Flip the power switch to turn the unit ON. The ETS will go through two steps to
begin normal operation:
a) It runs through a set of power-up diagnostics for approximately 12 seconds.
The LEDs show varying patterns corresponding to the tests being run.
b) It tries to obtain TCP/IP configuration information via DHCP, BOOTP, and
RARP. This may take as long as 15 seconds if no hosts answer the requests.
During this step, the OK LED blinks approximately 3 times per second and
the NET LED blinks occasionally.
7. Install EZWebCon on your 32-bit Windows PC computer. The EZWebCon
software is located on the distribution CD-ROM. Alternatively, download it from
ETSPR Product Descriptions
ETS16PR Front Panel
The ETS16PR has 16 RJ45 serial ports, a Reset button, an AUI Ethernet port, an
RJ45 Ethernet port for 10/100BASE-T, several LEDs, and a power switch.
Figure 2-4. ETS16PR Front Panel
Note: The first RJ45 port is also the serial console port. Use it as a method for the
initial setup or troubleshooting.
ETS Installation Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
ETS32PR Front Panel
The ETS32PR has 32 RJ45 serial ports, a Reset button, an AUI Ethernet port, an
RJ45 Ethernet port for 10/100BASE-T, several status LEDs, and a power switch.
Figure 2-5. ETS32PR Front Panel
Note: The first RJ45 port is also the serial console port. Use it as a method
for the initial setup or troubleshooting.
ETSPR LEDs
Each ETSPR has a total of 37 LEDs. Each serial port has one (ETS32PR) or two
(ETS16PR) corresponding LEDs that indicate receive and transmit activity, and there
are five status LEDs on the right side of the case.
Table 2-2. ETSPR Port LED Functionality
LED
activity
ok
Function
Blinks to indicate Ethernet activity
Blinks to indicate that the ETS is functioning
properly
100
Lights to indicate a 100BASE-T rather than
10BASE-T Ethernet link
link
Lights to indicate a functional Ethernet
network link
power
Lights to indicate the ETS has power
Installing the ETSPR
The following diagram shows a properly-installed ETS16PR. Installation will generally
be the same for all ETSPR models, the only difference being the number of serial
ports available. See ETSPR Product Descriptions on page 11 for more information.
12
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Figure 2-6. Sample ETSPR Network Layout (ETS16PR shown)
To install the ETS, complete the following steps in order:
1. Attach the two rack mount brackets to your ETS and attach your bracketed ETS
to your rack. The brackets should go on both front corners or both rear corners.
(This is only necessary if you would like to mount the unit on a rack.)
Figure 2-7. Rack Mount Bracket Installation
2. Connect one or more serial devices to the ETS.
Note: The default serial port settings are 9600 baud, 8 bit characters, no
parity, 1 stop bit, and Xon-Xoff flow control. See C:Pinouts for
information on what kinds of device attachments the ETS supports.
3. It is recommended to connect a terminal to the ETS console port (port 1). This
will enable you to receive diagnostic and initial configuration messages.
4. Connect an Ethernet cable to either the 10BASE-T port (shown) or a transceiver
connected to the AUI port.
Note: The ETS will boot without a valid Ethernet connection, but it will
pause to print a message (seen on the console port) asking if you want
to stop at the Boot> prompt. If you do not respond to this message, it will
wait for 10 seconds and then finish booting.
5. Attach one end of the power cable to the ETS and plug the other end into an
electrical outlet.
6. Flip the power switch to turn the unit ON. The ETS will go through two steps to
begin normal operation:
ETS Installation Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
a) It runs through a set of power-up diagnostics for approximately 12 seconds.
The LEDs show varying patterns corresponding to the tests being run.
b) It tries to obtain TCP/IP configuration information via DHCP, BOOTP, and
RARP. This may take as long as 15 seconds if no hosts answer the requests.
During this step, the OK LED blinks approximately 3 times per second and
the NET LED blinks occasionally.
7. Install EZWebCon on your 32-bit Windows PC computer. The EZWebCon
software is located on the distribution CD-ROM. Alternatively, download it from
14
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
It is important to consider the following points before logging into and configuring the
ETS:
‹
You must configure the ETS IP address before any TCP/IP functionality is
available. You cannot use the ThinWeb Manager until you have configured
an IP address.
‹
‹
Changing any server, service, or port setting requires privileged user status.
The default privileged password is system.
The login password is required for remote console logins. The default login
username is access. The login password is not required by default.
Note: If you would like to change either the privileged or login password, either use
EZWebCon or refer to the Device Server Reference Manual located on the CD-ROM.
Configuration Methods
EZWebCon
The EZWebCon configuration software is the recommended way to configure the
ETS. EZWebCon’s graphical user interface guides first time users through the initial
configuration process and allows experienced users to update any configurable
parameters.
EZWebCon requires a Java Virtual Machine (JVM) on the client. Lantronix provides
JVM installers for Solaris and 32-bit Windows users, as well as source code and
instructions for compiling it for other systems.
The EZWebCon software is located on the distribution CD-ROM. All instructions for
installing EZWebCon are provided in the README file. For assistance once
EZWebCon is running, refer to the EZWebCon on-line help.
Note: EZWebCon is also available from the Lantronix website and FTP server. See
D:Updating Software for more information.
Using a Web Browser (ETSPR models)
The ThinWeb Manager web browser interface allows you to log into and configure
your ETS using a standard web browser with JavaScript enabled. Simply type the
ETS IP address or resolvable text name into the browser’s URL/Location field (for
example, http://111.222.333.444).
Figure 3-1. Sample Web Browser Login
ETS Installation Guide
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Once you have connected to the ETS, you will see the Lantronix ThinWeb Manager
interface. Use the left-hand menu to navigate to subpages where you can configure
important settings as well as view statistics and other server information.
Note: Do not use the ThinWeb Manager until the IP is configured. See TCP/IP
Configuration.
Figure 3-2. ThinWeb Manager Interface
MENU
Incoming Logins
Incoming logins made via EZWebCon can be used to configure the ETS. Incoming
LAT and TCP/IP logins can also be used.
Incoming Telnet is only possible if your ETS has an IP address configured. Incoming
Telnet is enabled by default to allow TCP/IP connections. To change this setting, use
the Define Server Incoming command described in the Command Reference
chapter of the Device Server Reference Manual located on the CD-ROM.
Incoming logins do not prompt for a login password, so you may wish to disable them
for security reasons. If it is undesirable to disable incoming logins, the ETS can be
configured to prompt for a password with the Define Server Incoming Password
Enabled command.
Console Terminal
To configure the ETS via a console terminal, attach a terminal to the serial console
port (port 1) and press the Return key. You will see a Local> prompt at which you
can enter configuration commands.
TCP/IP Configuration
The EZWebCon configuration software is the easiest way to configure the ETS. The
following sections cover IP address configuration methods for TCP/IP hosts.
The ETS IP address must be configured before any TCP/IP functionality is available.
Use one of the following methods to set the IP address: EZWebCon; a directed Ping
packet; a BOOTP, DHCP, or RARP reply; or commands entered via the command
line interface on a terminal console.
Using EZWebCon
Use the following steps to assign an IP address using the EZWebCon Expert Shell.
1. From the Action menu, select Assign IP Address.
2. Enter or change the IP-related settings:
a) For Ethernet Address, enter the number that appears on the bottom label of
your ETS.
16
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
b) For IP Address, enter the desired IP address to use for this ETS. The IP
address should be on the same subnet as the PC running EZWebCon.
c) For Subnet Mask, change the values provided only if you wish to use a mask
other than the default. The default value should be correct in most cases.
d) For Loadhost, enter the IP address of the loadhost where you intend to store
your operating code.
3. Click OK.
4. Reboot the ETS. EZWebCon will let you know whether the configuration was
successful.
Note: If you have an older version of EZWebCon, refer to the ReadMe that was
included with it.
Using a Directed Ping Packet
The ARP/ping method is available under UNIX and Windows-based systems. If the
ETS has no IP address, it will set its address from the first directed IP packet it
receives.
On a UNIX host, create an entry in the host’s ARP table and substitute the intended
IP address and the hardware address of the ETS, then ping the ETS. This process
typically requires superuser privileges. The IP address should be on the same subnet
as the PC running EZWebCon.
Figure 3-3. ARP and Ping on UNIX
# arp -s 192.0.1.228 00:80:a3:xx:xx:xx
% ping 192.0.1.228
In order for the ARP command to work on Windows 95, the ARP table on the PC
must have at least one IP address defined other than its own. If the ARP table is
empty, the command will return an error message. Type ARP -A at the DOS
command prompt to verify that there is at least one entry in the ARP table.
Figure 3-4. ARP and Ping on Windows
C:\ ARP -S 192.0.1.228 00-80-A3-XX-XX-XX
C:\ PING 192.0.1.228
Note: There should be replies from the IP address if the ARP command
worked.
When the ETS receives the ping packet, it will notice that its IP address is not set and
will send out broadcasts to see if another node is using the specified address. If no
duplicate is found, the ETS will use the IP address and will respond to the ping
packet.
The ETS will not save the learned IP address permanently; this procedure is intended
as a temporary measure to enable EZWebCon to establish communication and allow
an administrator to Telnet into the ETS. Once logged in, the administrator can enter
the Define Server IPaddress command to make the address permanent.
Figure 3-5. Configuring Permanent IP Address
% telnet 192.0.1.228
Trying 192.0.1.228
Lantronix ETSx Version n.n/n (yymmdd)
ETS Installation Guide
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Type Help at the ‘Local_>’ prompt for assistance.
Enter Username> gopher
Local> SET PRIVILEGED
Password> system (not echoed)
Local>> DEFINE SERVER IPADDRESS 192.0.1.228
Local>> DEFINE SERVER SUBNET MASK 255.255.255.0
Any host wishing to access the ETS will have to be told the ETS’ IP address. This is
typically configured in the UNIX file /etc/hosts or via a nameserver. Refer to the host’s
documentation for additional information.
Using a BOOTP, DHCP, or RARP Reply
At boot time a host-based DHCP, BOOTP, or RARP server can respond to an ETS
request for an available IP address. For information about configuring the DHCP,
BOOTP, or RARP server, see your host documentation.
Using the Command Line Interface
1. Connect to the serial port (Port_1) using a console terminal or a terminal
emulation program, and press Enter. The serial port settings are 9600 baud, 8
bits, 1 stop bit, no parity.
2. Become the privileged user.
Figure 3-6. Becoming the Privileged User
Local> SET PRIVILEGED
Password> system (not echoed)
Local>>
3. Enter the new IP address.
Figure 3-7. Configuring the IP Address
Local>> define server ipaddress 192.0.1.201
Local>> DEFINE SERVER SUBNET MASK 255.255.255.0
For additional command line reference (for use with Telnet or a terminal console),
see the ETS Reference Manual available for download from
Was the Installation Successful?
If the ETS appears to be working and the unit is connected to the network, there are
a couple of ways to confirm that the unit is visible to network hosts:
‹
‹
If the ETS has an IP address, ping it from a TCP/IP host.
If the ETS has an IP address, use EZWebCon to log into it.
When you are satisfied that the ETS is working properly, proceed to 3:Getting
Started. If the ETS does not boot properly, see B:Troubleshooting.
18
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Using the ETS
The sections in this chapter show how to use the ETS in a variety of applications.
For detailed instructions on how to set up the ETS as a console server, see Console
Server Example.
For instructions on how to use the ETS in serial tunnel mode, see Serial Tunnel
Example on page 23.
For information about using the ETS with the Lantronix Comm Port Redirector, see
Comm Port Redirector on page 24.
Keep in mind that you must reboot the ETS after issuing a Define command. The
command will take effect when the ETS reboots. The one exception is that Define
Port commands take effect when a port is logged out.
Console Server Example
When you use the ETS as a console server, you can remotely manage devices and
equipment from anywhere on the network.
Figure 4-1. Console Server
To use the ETS as a console server, you must connect the ETS serial ports to the
serial console/management ports of other equipment such as UNIX servers, PBX
switches, routers, network switches, or other similar devices.
Once you have completed the connections, you can establish a Telnet connection to
the ETS IP address and socket number of the desired port. The ETS serial ports
allow two types of socket connections: Telnet IAC interpretation at socket 200x, and
raw TCP connections at socket 300x, where x is the port number. For example, to
open a Telnet connection to port 4 of an ETS at IP address 192.0.1.168, you would
issue the command “Telnet 192.0.1.168 2004” from your system prompt. In a
Windows environment, use a space instead of a colon in the command syntax.
ETS Installation Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the ETS
In addition to direct Telnet connections, you can use the ETS’ built-in menu feature.
The ETS menu allows you to connect to the IP address of the ETS and be greeted
with a menu with which to connect to each attached serial device. Menu choices are
an easy way to let users access often-used hosts and services without needing to
know any ETS command syntax, the IP addresses of the non-local devices, or the
socket numbers involved.
Figure 4-2. Sample Menu
Define the Menus
To give your menu a name, use a Define Menu Title command.
Figure 4-3. Menu Title
Local>> DEFINE MENU TITLE “Lantronix Console Server:”
Create menus entries with the Define Menu command. (To temporarily test menu
entries without making them permanent, you may choose to use the Set Menu
command.) Users type the number of the command they wish to execute and press
Enter.
The basic syntax of the Define Menu command includes:
‹
‹
‹
a menu item number
a menu item name
a command that is executed when the user chooses that menu item.
Figure 4-4. Generic Menu Command
Local>> DEFINE MENU n “Name” “command”
NOTE: You must enclose both the menu item and the command in their own
sets of quotation marks.
There are three types of menu entries.
‹
‹
‹
Those that connect users to devices on the network (see Figure 4-5)
Those that connect users to devices attached to the ETS (see Figure 4-6)
Those that function locally on the ETS (see Figure 4-7)
To allow users to connect to a device on the network from a terminal connected to
the ETS, use a Telnet command.
Figure 4-5. Menu Entries for network Connections
Local>> DEFINE MENU 1 “Cisco Router” “telnet 192.0.1.250;kill”
Local>> DEFINE MENU 2 “Sun Server” “telnet 192.0.1.251;kill”
To allow users to connect from the network to a device connected to the ETS (or
from one ETS port to another) add a Connect Local command.
20
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the ETS
Figure 4-6. Menu Entries for manipulating the ETS
Local>> DEFINE MENU 3 “HPUX Server” “connect local port_3”
Local>> DEFINE MENU 4 “Linux Server” “connect local port_4”
Local>> DEFINE MENU 5 “PBX Switch” “connect local port_5”
To allow users to access a local service on the ETS, add a general ETS command.
Figure 4-7. Menu Entries for manipulating the ETS
Local>> DEFINE MENU 6 “ETS Prompt” “exit”
Local>> DEFINE MENU 7 “Logout” “logout”
NOTE: The Exit command only works in menu mode. It allows users to
return to the Local> prompt on the ETS on which the menu was configured.
It is helpful to include this command in your menus until you have full tested
them – otherwise there is no way for users on menu mode ports to return to
the Local> prompt.
To review the menu that you have just created, type List Menu at the Local>
prompt. The menu created by the previous commands would look like this:
Figure 4-8. New Menu
Local_1>> show menu
Title for the menu is "Lantronix Console Server"
1: Cisco Router --> "telnet 192.0.1.250;kill"
2: Sun Server --> "telnet 192.0.1.251;kill"
3: HPUX Server --> "connect local port_3"
4: Linux Server --> "connect local port_4"
5: PBX Switch --> "connect local port_5"
6: ETS Prompt --> "exit"
7: Logout --> "logout"
Enable Menu Mode
You must enable menu mode for all ports on which you wish the menu system to
work. Ports 2-4 will be used for the examples in this section.
Figure 4-9. Enabling Menu Mode
Local>> DEFINE PORT 2-4 MENU ENABLED
Local>> LOGOUT PORT 2-4
Note: If you want incoming logins from the network to be able to use the
menu, you must enable menu mode on port 0.
Users who Telnet into the ETS would see the menu rather than the Local> prompt.
Note: Administrators can bypass the menu and get to the ETS command line by
forming a Telnet connection to port 7000.
Configure Switches
Switches allow users to move around within open sessions and return to the ETS
Local> prompt if needed. Configure a local switch to return to the local prompt.
Also, configure backward and forward switches if you intend to allow serial port users
to hold multiple sessions to remote servers. You must set switches for all of the ports
for which menu mode is enabled (see Define the Menus on page 20).
Any key may be used for a switch, provided that the chosen keys do not interfere with
the sessions. To use a control key, type a carat (^).
ETS Installation Guide
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the ETS
Figure 4-10. Configuring Switches
Local>> DEFINE PORT 2-4 LOCAL SWITCH ^X
Local>> DEFINE PORT 2-4 FORWARD SWITCH ^F
Local>> DEFINE PORT 2-4 BACKWARD SWITCH ^B
Local>> DEFINE PORT 2-4 BREAK LOCAL
Note: Define Port Break Local allows the ETS to recognize the switches you
just configured.
To check switch configurations, enter the Show/List Port command and specify the
ports that are used for menu mode.
Figure 4-11. Show Port Screen
Using Menus
When you log into a port with menu mode enabled, you will be presented with an
initial login screen.
Figure 4-12. Login Screen
Lantronix ETSxx Version B3.6/3 (000410)
Type HELP at the 'Local_10> ' prompt for
assistance.
Username>
1. Enter your user name (in this case, Bob) and press Enter.
Figure 4-13. Login Screen, part 2
Username> Bob
Press <CR> to continue...
2. As instructed, press the Return key once more to see the actual menu.
Figure 4-14. Login Menu
3. Type the number of the desired option and press Enter. For example, to connect
to the Linux server, press 4 and then press Enter.
22
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the ETS
4. To return to the menu from your Linux session, press the configured Local Switch
key. In this case, the Local Switch is Ctrl-X (see Figure 4-10).
Note: Switch keys only work within sessions. They do not work from the menu
screen - you must enter a menu number to go to a session from the menu screen.
Serial Tunnel Example
Two ETS device servers can be connected to emulate a direct serial connection
across a LAN or WAN. Servers connected in this way can pass data only—they will
not be able to pass status signals (DSR/DTR, CTS/RTS, etc.) or preserve timing
between characters. The basic network configuration for this virtual serial line is
shown in Figure 4-15.
Figure 4-15. Back-to-Back ETS Connections
TCP Configuration
Assuming the ETS serial port parameters have been configured properly, the ETS
device servers in Figure 4-15 are configured as follows:
ETS_A
Local>> DEFINE PORT 2 DEDICATED TELNET 192.168.5.10:3001T
Local>> DEFINE PORT 2 AUTOSTART ENABLED
ETS_B
Local>> DEFINE PORT 3 ACCESS REMOTE
Local>> DEFINE PORT 3 DEDICATED NONE
Local>> DEFINE PORT 3 AUTOSTART DISABLED
Note: If the ETS device servers are on different IP subnets, configure the
default gateway on each unit with the Change Gateway command.
The above commands create a raw (8-bit clean) TCP connection between ETS_A
port 2 and ETS_B port 3 once the units have been power-cycled. The commands for
ETS_A ensure that it will automatically connect to ETS_B each time it is booted. The
commands for ETS_B ensure that it is always available to accept connections from
ETS_A. Once this connection is made, data is able to travel in both directions.
Note: You must log out the ETS ports after configuring them so that the commands
can take effect.
ETS Installation Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the ETS
UDP Configuration
When the UDP protocol is used, there is no connection; each ETS must be told
explicitly which hosts it is allowed to accept packets from. Each ETS would have to
be configured to both send packets to and accept packets from the other ETS.
ETS_A
Local>> DEFINE PORT 2 DEDICATED TELNET 192.168.5.10:4096U
Local>> DEFINE PORT 2 AUTOSTART ENABLED
Local>> DEFINE PORT 2 ACCESS DYNAMIC
ETS_B
Local>> DEFINE PORT 3 DEDICATED TELNET 192.168.5.2:4096U
Local>> DEFINE PORT 3 AUTOSTART ENABLED
Local>> DEFINE PORT 3 ACCESS DYNAMIC
Note: For further information on applicable environment strings, refer to the
ETS Reference Manual.
Setting up dedicated hosts ensures that the units will always talk to each other.
Enabling Autostart for both units enables one ETS to send data to the other ETS
without having to wait for a serial carriage return to start the session. ETS_B knows
exactly which other ETS to accept connections from. Finally, when Autostart is
enabled, the access mode must be either Local or Dynamic (Dynamic is more
flexible).
Multi-port Serial Tunnel Configuration
You can create serial tunnels for any available ports on the ETS. Each serial tunnel
must point from one ETS port to one different serial device port (such as a serial port
on an ETS, MSS, or UDS server).
Comm Port Redirector
The Lantronix Comm Port Redirector application allows PCs to share modems and
other serial devices connected to an ETS using Microsoft Windows or DOS
communication applications. The Redirector intercepts communications to specified
Comm ports and sends them over an IP network connection to the ETS serial port.
This enables the PC to use the ETS serial port as if it were one of the PC Comm
ports. Using their existing communications software, PC users dial out to a remote
host through a modem connected to the ETS.
The Comm Port Redirector software and installation instructions are included on the
24
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5: Printing on the ETS
The EZWebCon configuration software is the easiest method for ETS configuration.
The following sections cover print configuration methods for TCP/IP hosts.
Note: Printing directly to a port is the easiest method for printing to the ETS.
If you would like instructions for printing to a service, see the Device Server
Reference Manual located on the CD-ROM.
LPR Printing
The ETS provides several major methods of printing via TCP/IP such as TCP/IP
socket printing and Berkeley remote LPR and RTEL host software.
Two parameters must be configured for LPR printing:
1. The IP address or host name of the ETS.
2. The remote output queue (the name of the service on the ETS).
In addition, there are a few important things to note about LPR printing:
‹
Windows for Workgroups, Windows 95, and Windows 98 do not support LPR
directly; however, Lantronix has provided a peer-to-peer printing solution on
the distribution CD-ROM.
‹
Because of the way the LPR protocol is typically implemented on the host,
the processing options and banner page are sent after the job data itself. The
ETS will print a banner page at the end of a job, and cannot support most of
the LPR options. If it is necessary to have the banner page at the beginning
of the printout, install and use the RTEL software. If banners are not needed,
they can be disabled.
‹
‹
‹
The ETS cannot print multiple copies of the print job when using the “-#n” lpr
option.
If two print queues on the host refer to two services on the same ETS, they
must use separate spooling directories.
No special purpose input or output filters can be used when printing via LPR.
If this functionality is necessary, use the named pipe interface program in the
RTEL print queue configuration software.
Services
With few exceptions, you must create a service before you can configure print
queues on the ETS. A service is a resource accessible to network hosts. A Lantronix
service is also known as a remote printer name or remote queue name on many
operating systems.
LPR on Windows 2000, XP, and 2003
Two methods of printing to the Lantronix ETS devices are supported by Windows
2000, XP and 2003.
ETS Installation Guide
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
‹
Creating a Standard TCP/IP port allows communication through a RAW
Telnet port. This is supported by default.
‹
Creating a LPR port allowing jobs to be submitted to a “Service” offered by
the ETS. Services are the basic method allowing the ETS to provide a
queuing mechanism to a network host. (See the ETS Reference Manual for
in-depth instructions on creating queues.)
To enable LPR support, install Print Services for UNIX:
1. From the Windows’ Start Menu, select Settings Æ Control Panel.
2. Select Add/Remove Programs.
3. Select Add/Remove Windows Components.
4. Select Other Network File and Print Services.
To initiate either of the print methods, follow these steps:
1. From the Windows’ Start Menu, select Settings Æ Printers and Faxes (or
Printers).
2. Select Add Printer.
3. Select Local Printer attached to this computer. De-select Automatically
detect and install my Plug and Play printer. Click Next.
4. In the Select a Printer Port dialog box, select Standard TCP/IP Port from the
Create a new port drop-down menu. Click Next.
26
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
5. In the Add Port dialog box, enter the IP address of the ETS in the Printer Name
or IP Address field. Enter a user-friendly name in the Port Name field.
(Windows uses this as the display name for this printer configuration).
ETS Installation Guide
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
6. In the Additional Information required dialog box, select Custom as the Device
Type. Click Settings.
7. If configuring the printer to use a Standard TCP/IP port, select RAW. Identify the
appropriate ETS port to use in the Port Number field.
28
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
Note: Lantronix uses the following convention to identify the TCP ports on
the ETS: 3000 + port number. For example: Port 1 = 3001, Port 2 = 3002,
Port 3 = 3003 etc.
8. If configuring the printer to use a LPR port, select LPR. Identify the appropriate
ETS service to use in the Queue Name field.
To determine the services running on the ETS do the following:
Access the ETS Local>prompt (via telnet or a terminal console).
Type SET PRIV and enter the privileged user password (default password is
SYSTEM) .
Type SHOW SERVICES LOCAL.
To configure a service, use the following commands from the privileged user
prompt on the ETS:
Local>> DEFINE SERVICE (ETS_HPLaserjet) port
(x) enable
(substitute your own values for the entries in parentheses)
Local>> INITIALIZE DELAY 0
After the reboot use the following command to display the status of the newly defined
service:
Local>> SHOW SERVICE (ETS_HPLaserjet) CHAR
9. Click OK. Click Next.
10. Identify the Manufacturer and Model of the print device used. Provide the
appropriate driver if prompted.
ETS Installation Guide
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
11. Click Next. Click Finish.
LPR on Windows NT 3.5.1 (and later)
This section assumes that TCP/IP, Simple TCP/IP, and Microsoft TCP/IP printing
have been installed on the Windows NT host.
1. In the Control Panel, double-click the Printers icon.
2. Double-click the Add Printer icon.
3. In the window that appears, choose My computer and click Next.
4. Select the Add Port button and click Next.
30
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
5. Select LPR Port.
Note: If LPR Port is not an option, open the Network Control Panel and add
“Microsoft TCP/IP Printing” to the List of services.
6. Enter the name or IP address of your ETS on the first line, and enter the name of
your ETS print service on the second line.
7. Select the manufacturer and printer type.
8. Enter the queue name.
ETS Installation Guide
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
9. If applicable, choose Shared and select the type of operating system that the
printer will be working with. (First confirm that the print queue is working).
10. Test the printer by choosing Yes and clicking Finish.
LPR on Windows 95/98
Lantronix provides a utility to enable LPR printing on Windows 95/98. To request this
utility, contact Lantronix Technical Support and ask for “ltxlpr.exe”.
1. Install the file ltxlpr.exe. Once installation is complete, a ReadMe file will open
automatically.
2. Follow the directions in the ReadMe file to configure LPR on your PC.
LPR on UNIX Hosts
The Berkeley remote printing system is supported on many machines, and is simple
to configure. This section describes how to configure LPR print queues on generic
UNIX hosts such as SUN hosts. There are slight variations in LPR configuration for
AIX, HP, and SCO hosts, as will be explained in the following sections.
1. Install a print queue on your host by adding the ETS name and IP address to the
/etc/hosts file:
32
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
Figure 5-1. Adding /etc/hosts Entry
xxx.xxx.xxx.xxx ETS_xxxxxx
2. Add the host print queue to the /etc/printcap file. The punctuation shown in
Figure 5-7 is required, and no extra spaces should be added.
Figure 5-2. Adding /etc/printcap Entry
ets_prt|Printer on LAB ETS:\
:rm=ETS_xxxxxx:\
:rp=ETS_xxxxxx_TEXT:\
:sd=/usr/spool/lpd/ets_prt:
This will create a host queue named ets_prt. The rm parameter is the name of the
ETS in the host's address file, the rp parameter is the name of the service as it
exists on the ETS, and the sd parameter specifies the name of a directory used to
hold temporary spooling files.
3. Create a world-writable spooling directory using the mkdir command.
Figure 5-3. Creating Spooling Directory
# mkdir /usr/spool/lpd/ets_prt
# chmod 777 /usr/spool/lpd/ets_prt
4. If desired, use the mx option to allow unlimited size files to be printed and the sh
option to prevent header pages from being generated. See the host's
documentation or man pages for more information on the format of the printcap
file and how to create the spool directory.
5. Print to the queue using normal lpr commands:
Figure 5-4. Printing to Queue
% lpr –P ets_prt /etc/hosts
LPR on AIX Hosts
The System Management Interface Tool (SMIT) allows you to enable LPD printing
and create print queues. LPR has only been tested on AIX versions 3.2 and higher.
To create a print queue:
1. At the host prompt, type smit.
2. Choose Print Spooling.
3. Choose Manage Print Server and Start the Print Server Subsystem (lpd
daemon).
4. In the Start the Print Server Subsystem dialog box, type both in the first field.
5. The message “The lpd subsystem has been started” will appear. Click Done.
To add a print queue:
1. From the main window, choose Print Spooling.
2. Choose Manage Print Server and Manage Print Queues.
3. Choose Add a print queue.
ETS Installation Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
4. From the dialog box that appears, choose remote.
5. From the next dialog box, choose Remote Printing.
6. The Add a Standard Remote Print Queue dialog box will appear. Enter the
following information.
‹
‹
‹
‹
‹
The name of the print queue,
The name of the ETS unit,
The name of the ETS service,
The type of print spooler on the remote server, and
A description of the printer on the remote server.
7. A dialog box will appear: “Added print queue ets_prt”. Click Done.
Note: If you are unable to use SMIT, see the Device Server Reference
Manual on the CD-ROM for UNIX commands used to set up print queues.
8. Print to the queue using normal lp syntax.
Figure 5-5. Printing to Queue
% lp -dets_prt filename
LPR on HP Hosts
The System Administration Manager (SAM) allows you to create print queues.
Note: If you are unable to use SAM, the Device Server Reference Manual
located on the CD-ROM describes UNIX commands that can be used to set
up print queues.
To create a print queue:
1. At the HP prompt, type sam.
2. From the main application window, choose Printers and Plotters.
3. In the Printers and Plotters window, choose Printers/Plotters.
4. In the pull-down menu, select Remote Printer/Plotter from the Actions menu.
5. The Add Remote Printer window will appear. SAM will prompt you for:
‹
‹
‹
‹
‹
The printer name (the name of the print queue),
The remote system name (the ETS name),
The remote printer name (the ETS service),
The remote cancel model, and
The remote status model.
LPR on SCO UNIX Hosts
LPR is supported in SCO V3.2 release 4 with TCP/IP Version 1.2 and greater.
To configure a print queue using LPR, issue the mkdev rlp command. This will install
the Berkeley remote printing files and executable programs.
Note: The mkdev rlp command should only be issued once, or serious
problems will occur. If this happens, contact SCO technical support.
You can print to this queue using normal lp syntax once the remote printer is set up.
To create a remote printer:
1. Issue the rlpconf command.
34
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
2. Answer the questions that follow.
Figure 5-6. Configuring Remote Printer
Remote Printing Configuration
Enter information for remote printers or local
printers accepting remote printing requests
Please enter the printer name (q to quit):
backupprinter
Is printer backupprinter a remote printer or a
local printer? (r/l) r
Please enter the name of the remote host that
backupprinter is attached to: ETS_xxxxxx
The backupprinter is connected to host ETS_xxxxxx.
Is this correct? (y/n) y
Would you like this to be the sys.default printer?
(y/n) y
Make sure your hostname appears in ETS_PRT’s
/etc/hosts.equivor or /etc/hosts:lpd file.
Make sure backupprinter appears in /etc/printcap
(in BSD format).
Make sure backupprinter has a spool directory on
ETS_PRT.
Putting the printer in printer description file and
creating spool directory... done
Updating LP information... done
In the example, the printer name is your ETS service name, and the remote host
name is the name of your ETS as it is listed in your hosts file.
During initial configuration, the queue name must be the same as the remote printer
name. However, you may change the queue name later by manually editing the
printcap file.
RTEL Functionality
If the LPR method of printing is not adequate for an application (for example, if you
need banners before jobs, or more flexibility), configure the Lantronix-supplied RTEL
software on the host. After installing the software configuring the connections to the
ETS, you can use normal UNIX print commands and queue utilities such as lpc and
lpstat.
Note: RTEL binaries are provided for many systems. Source code is also
provided for use on non-supported systems. Download it from
To print to the ETS using special formatting or using third-party software packages,
you may have to create print pipes on the host. The RTEL software provides this
functionality by providing a UNIX named-pipe interface.
To recreate the RTEL source files:
1. Copy the file RTEL_SRC.TAR in binary mode from the distribution CD-ROM to
the UNIX host.
2. Untar the archive.
3. See the README files in the created directories that describe the contents of the
RTEL distribution and man pages that describe the actual software functionality.
ETS Installation Guide
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing on the ETS
Unix Host Troubleshooting
Table 5-1. TCP Troubleshooting
Area to Check
Explanation
The ETS IP address
Telnet to the ETS using the name in the host file
and name are entered and verify that the ETS name is resolvable and
in the host file.
that the ETS is reachable via the network.
Jobs that appear in
the host queue reach
the ETS
From within the LPC administrative utility, enter
these commands to clear and reset the host
queue:
abort queue
clear queue
enable queue
start queue
36
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6: NetWare Configuration
The EZWebCon configuration software is the easiest way to configure the ETS. The
following sections cover print configuration methods for NetWare hosts.
Note: The ETS needs an IP address before you can use EZWebCon. See
TCP/IP Configuration on page 16 for instructions.
This chapter explains creating NDS print queues with NetWare Administrator and
with the PCONSOLE Quick Setup option. To create NDS print queues, you must be
running NetWare version 4.x with NDS capabilities.
If you are running NetWare versions 2.x, 3.x, or version 4.x with bindery emulation,
you may configure bindery print queues using QINST (bindery only) or PCONSOLE.
For more information, see the NetWare chapter of the Device Server Reference
Manual located on the CD-ROM.
NDPS Printing
Lantronix Terminal and Print Servers support Novell's NDPS for printing using the
Novell NDPS Gateway. For instruction on setting up NDPS, refer to your Novell
documentation. Lantronix also provides information on setting up NDPS in our FAQs
on our support web site (http://www.lantronix.com/support).
NDS Print Queues
Obtain an NDS License
If you wish to create NDS print queues, you must read and complete an NDS
registration form via one of the following methods:
‹
Using a forms-capable Internet browser, navigate to the Lantronix World
and find the Novell NDS Registration link.
‹
‹
form that can be completed and returned to Lantronix.
If you don’t have Internet access, contact a Lantronix technical support
representative for assistance. Contact information is provided in A:Contact
Information.
Configure your ETS
1. License NDS on your ETS using the string obtained from Lantronix.
Figure 6-1. Licensing NDS
Local>> DEFINE PROTOCOL NETWARE DSLICENSE licensestring
2. Define the directory service tree in which the ETS is located.
ETS Installation Guide
37
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare Configuration
Figure 6-2. Defining Directory Service Tree
Local>> DEFINE PROTOCOL NETWARE DSTREE foodco
Note: For an explanation of the structure of the NetWare Directory Service
tree, see your host documentation.
3. Define the directory service context in which the ETS is located.
Figure 6-3. Defining Directory Service Context
Local>> DEFINE PROTOCOL NETWARE DSCONTEXT
ou=kiwi.ou=exotic.o=fruit
4. Enter the List Protocol NetWare Access command to ensure that at least one
of the file servers in the directory service tree is in the access list.
5. If desired file server is not in the access list, add it.
Figure 6-4. Defining Access List
Local>> DEFINE PROTOCOL NETWARE ACCESS fileserver
6. Reboot the ETS.
Figure 6-5. Rebooting
Local>> INITIALIZE DELAY 0
NetWare Administrator Quick Setup Print Queues
The NetWare Administrator management utility allows you to manage network
resources, such as queue-based print services, in a tree structure. You can either
use the Quick Setup option or individually create printing-related objects.
Note: NetWare Administrator can be used for both NDS and bindery print
queues.
To create a print queue with the Quick Setup option:
1. Start the NetWare Administrator.
2. In the Directory Tree windows, select the context in which to install the printer.
3. From the Menu Bar, select Tools: Print Services Quick Setup.
4. In the Print Server Name field, enter the name of your ETS (viewable by entering
the Show Server command at the Local> prompt).
5. In the Printer Name field, enter the name of the desired print service configured
on your ETS. For example, ETS_xxxxxx.
6. In the Print Queue Name field, enter the name of the print queue to create. The
name should be meaningful to you; it will not affect ETS configuration.
7. Click Create.
8. Reboot the ETS.
PCONSOLE Print Queues
1. Log in as Admin on the file server you will be changing.
2. At the prompt, type PCONSOLE to start the utility.
For example, if your file server is mapped to the F: drive, you would use the F:
prompt.
38
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare Configuration
3. From the main menu, choose Quick Set-Up.
4. When prompted by PCONSOLE, enter the information with which to configure
the print queue.
‹
‹
‹
‹
The print server name (ETS_xxxxxx),
The new printer name (service name, such as ETS_xxxxxx),
The new print queue name, and
The print queue volume (the name of the file server from which the printer
receives print requests).
‹
The remaining fields can be left in their default settings.
5. Press the F10 key to save the print queue information.
6. Reboot the ETS.
NetWare Host Troubleshooting
Table 6-1. NetWare Host Troubleshooting (Bindery Mode)
Area to Check
Explanation
The print server
names in
Use PCONSOLE to check.
PCONSOLE match
the ETS name and its
service name
The ETS NetWare
access table
Use the Show Protocols NetWare Access
command. Scanning too many file servers can
cause a delay between jobs. Configure the
access list to only scan for jobs on the file servers
of interest.
Table 6-2. NetWare Host Troubleshooting (NDS)
Area to Check
Explanation
The ETS NetWare
access table
Use the Show Protocols NetWare Access
command. By default, only local file servers are
scanned for queues.
The ETS login
The passwords must match or the ETS will not
be able to log into the file servers to scan for
jobs.
password and the
queue password on
the file server
The ETS has
successfully attached
to the queue
Type NETSTAT at the Local> prompt. This will
display information about fileservers, printers,
and queues that the ETS has found. If a queue is
in JobPoll, the ETS has successfully attached to
the queue.
ETS Installation Guide
39
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare Configuration
Area to Check
Explanation
The DSTree,
DSContext, and
Type Show Protocol NetWare NDS. This
command shows the tree and the context that
you have configured, a failure code, and an NDS
error code for each server.
DSLicense
DSTree is the directory service tree on which the
ETS is located. DSContext is the context where
the ETS is located; it must match the context on
the file server (The DSContext must be of the
following form: ou=fruit.o=exotic). DSLicensed
should be yes.
Printer and queue
changes have
propagated through
the NDS tree
It may take a few minutes for the changes to
propagate. If the ETS doesn’t attach, reboot the
ETS.
Table 6-3. NDS Errors from the File Server
Code
Meaning
Remedy
0xfffffda7
Object could not be
found in the given
context
Check the ETS server name, DScontext,
and DStree to ensure the printer server is
set up correctly with PCONSOLE.
0xfffffda5
0xfffffd69
Requested attribute
could not be found
Use PCONSOLE to ensure that the ETS
has associated printers and the printers
have associated queues.
DS Database is
locked
An administrator is probably updating the
database. Wait a few minutes and issue
the Set Protocol NetWare Reset
command.
0xfffffd63
0xfffffd54
Invalid password
The password for the print server object
under PCONSOLE must match the ETS
login password. If the login password on
the ETS is left as the default (access),
there should be no password for the print
server object.
Secure NCP
violation
Turn down the NCP packet signature
level so that it is not required.
Table 6-4. NDS Errors from the File Server
Bit
Meaning
Remedy
1
Server out of
memory
Turn the ETS off, wait a few seconds, and
turn it back on. Disable unused protocols
and/or remove fileservers without print
queues from the NetWare access list.
2, 3
4
Unexpected
response from file
server
Report the problem to Lantronix
Technical Support.
No printers found for Ensure that there are printers for the
the ETS
ETS, and the printer names match the
service names on the ETS.
5
6
No printer queue
found
Ensure that the printers have associated
queues.
Login failed
Ensure there is a print server object
configured with the same name as the
ETS.
40
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare Configuration
Bit
Meaning
Remedy
7
Authentication failed Ensure the ETS login password is the
same as the print server object password.
If the ETS is using the default password
(access), there should be no print server
object password.
ETS Installation Guide
41
Download from Www.Somanuals.com. All Manuals Search And Download.
7: LAT Configuration
The EZWebCon configuration software is the easiest way to configure the ETS. The
following sections cover print configuration methods for LAT hosts.
Note: The ETS needs an IP address before you can use EZWebCon. .
To use LAT you must obtain a LAT license from your dealer or Lantronix and use the
Set/Define Protocol LAT License command on your ETS. LAT print queues can be
created by printing to a port or printing to a service. Printing directly to a port requires
no ETS configuration.
Printing Directly to a Port
1. Create a LAT application port that references the ETS port.
Figure 7-1. Creating LAT Application Port
$ RUN SYS$SYSTEM:LATCP
LATCP> CREATE PORT LTAnnn/APPLICATION
LATCP> SET PORT LTAnnn/NODE=ETS_xxxxxx/PORT=Port_n
LATCP> EXIT
2. Create and start a print queue that uses the LAT application port.
Figure 7-2. Creating and Starting Print Queue
$
INITIALIZE/QUEUE/START/ON=LTAnnn:/PROCESSOR=LATSYM
/RETAIN=ERROR queue_name
3. Add the commands to the SYS$MANAGER:LAT$STARTUP.COM file so the
required LAT devices will be recreated after each host reboot.
Note: LAT terminal device characteristics may have to be changed to correctly print
certain files. See your VMS documentation for more information.
4. Print to the queue.
Figure 7-3. Printing to Queue
$ PRINT/QUEUE=queue_name filename.txt
LAT Host Troubleshooting
By default, the LAT error message codes on the host are not translated into text error
messages. If a LAT job fails and appears in the queue with an eight-digit hex result
code, the code can be translated by issuing the following commands:
ETS Installation Guide
42
Download from Www.Somanuals.com. All Manuals Search And Download.
LAT Configuration
Figure 7-4. Translating LAT Error Codes
$ SHOW QUEUE/FULL/ALL queue_name
(note the error code nnnnnnnn)
$ SET MESSAGE SYS$MESSAGE:NETWRKMSG.EXE
$ EXIT %Xnnnnnnnn
Table 7-1. Troubleshooting LAT Configurations Using a Port
Area to Check
Explanation
The specified node
name matches the
ETS node name
Use the Show Server command to verify.
The specified port
name matches the
port’s name
Use the List Port 1 command to verify.
Table 7-2. Troubleshooting LAT configurations Using a Service
Area to Check Explanation
The unit is licensed for LAT To use LAT you must obtain a LAT license
from your dealer or from Lantronix. Then
enter the Define Protocol LAT License
string command on your ETS.
The specified node name
matches the ETS node
name
Use the Show Server command.
The service name used
matches the configured
service name
Use the Show Service Local Characteristics
command.
The service is available
Use the Show Service Local Characteristics
command from a network login. If the
service rating is zero, the serial port is in
use.
The LAT characteristic has
been enabled on the
service
Use the Show Service Local Characteristics
command from a network login.
The LAT symbiont is
specified as the queue
process on the VMS host
Use the VMS command Show Queue/Full
queue_name to see the queue
characteristics.
For DCPS: there is a
bidirectional path to the
printer and the printer is
locked into PostScript
mode
Lock the printer in PostScript mode and
issue the Test Service PostScript Count n
command. This command sends a job to
the printer and waits for the response.
ETS Installation Guide
43
Download from Www.Somanuals.com. All Manuals Search And Download.
8: AppleTalk Configuration
The EZWebCon configuration software is the easiest way to configure the ETS. The
following sections cover print configuration methods for AppleTalk hosts.
Note: The ETS needs an IP address before you can use EZWebCon.
Note: Macintoshes that do not support EtherTalk will need either an Ethernet
card or a LocalTalk-to-EtherTalk router to use the ETS.
Bitronics
Printing from a Macintosh is only possible with a PostScript printer and bi-directional
communication between the ETS and that printer. The ETS supports the Bitronics
interface, an extension to the standard Centronics interface. Printers that support
Bitronics allow bi-directional communication. To enable Bitronics on an ETS port, use
the Define Port 2 Bitronics Enabled command.
Note: MacOS 8.1 can also print via LPD. See the Device Server Reference
Manual located on the CD-ROM and web site for configuration instructions.
Macintosh Services
Before attempting to print from a Macintosh, ensure that AppleTalk and PostScript
are both enabled on at least one service. Once a PostScript AppleTalk service is
configured, the service will appear in the Chooser as a LaserWriter in the same zone
as the ETS. Select the service in the Chooser and complete the appropriate setup
options. Then close the Chooser window and print a test page of text to the
Macintosh service.
AppleTalk Zones
If there is a router on the network, the ETS will appear in the default zone specified
by the router. To change the default zone use the Define Protocol AppleTalk Zone
command.
If the ETS is attached to a network without an AppleTalk router, all AppleTalk devices
(including the ETS) will appear in the default zone in the Chooser.
Note: If no router is present on the network, the ETS will not accept
AppleTalk print jobs for 60 seconds after booting.
ETS Installation Guide
44
Download from Www.Somanuals.com. All Manuals Search And Download.
AppleTalk Configuration
AppleTalk Host Troubleshooting
Table 8-1. AppleTalk Host Troubleshooting
Area to Check Explanation
The printer is available to
be selected in the Chooser
Make sure the printer is in the right zone.
Bidirectional
communication
Lock the printer in PostScript mode and
issue the Test Service PostScript Count n
command. This sends a job to the printer
and waits for the response.
ETS Installation Guide
45
Download from Www.Somanuals.com. All Manuals Search And Download.
9: DLC Configuration for LAN Manager
The EZWebCon configuration software is the easiest way to configure the ETS. This
chapter explains DLC/Digital Network Port configuration for Windows NT 4.x hosts.
Note: The Server needs an IP address before you can use EZWebCon.
Printing using an LPD client is the preferred method for sending print jobs to the ETS.
Windows 95 does not support DLC printing (see 5:Printing on the ETS for more
information).
DLC Configuration
ETS Configuration
To use the DLC protocol, you must have one service with the DLC characteristic
enabled.
Note: The DLC characteristic may be associated with only one service on a
given ETS.
Figure 9-1. Enabling DLC
Local>> DEFINE SERVICE ETS_xxxxxx DLC ENABLED
Host Configuration
To send print jobs from a Windows NT host to the ETS, add the ETS as a Windows
NT printer.
1. Double-click the Printers icon in the Control Panel.
2. Double-click the Add Printer icon.
3. In the window that appears, select My Computer and click Next.
4. Select the Add Port button.
5. Select Hewlett-Packard Network Port and click New Port.
6. If Hewlett-Packard port is not one of the available options, you must install DLC
printing from your Windows NT system disks. DLC is not installed by default.
7. Enter the ETS hardware address. It is printed on the ETS bottom label.
8. Select Job-based.
9. Select the manufacturer and printer type.
10. Enter the queue name.
11. If applicable, choose Shared and select the operating system the printer will be
working with. (First confirm that the print queue is working.)
12. Test the printer.
ETS Installation Guide
46
Download from Www.Somanuals.com. All Manuals Search And Download.
A: Contact Information
If you are experiencing an error that is not described in this book, or if you are unable
to fix the error, you may:
‹
To check our online knowledge base or send a question to Technical
Email us at [email protected].
Call us at:
‹
‹
(800) 422-7044 Domestic
(949) 453-7198 International
(949) 450-7226 Fax
Our phone lines are open from 6:00AM - 5:30 PM Pacific Time Monday through
Friday excluding holidays.
Technical Support Europe, Middle East, and Africa
Phone: +49 (0) 89 31787 817
Firmware downloads, FAQs, and the most up-to-date documentation are available at:
When you report a problem, please provide the following information:
‹
‹
‹
‹
‹
‹
‹
‹
Your name, and your company name, address, and phone number
Lantronix ETS model number
Lantronix ETS serial number
Software version (use the Show Server command to display)
Network configuration, including the information from a Netstat command
Description of the problem
Debug report (stack dump), if applicable
Status of the unit when the problem occurred (please try to include
information on user and network activity at the time of the problem).
ETS Installation Guide
47
Download from Www.Somanuals.com. All Manuals Search And Download.
B: Troubleshooting
This appendix discusses how to diagnose and fix errors quickly yourself without
having to contact a dealer or Lantronix. It will help to connect a terminal to the serial
port while diagnosing an error to view any summary messages that are displayed.
When troubleshooting, always ensure that the physical connections (power cable,
network cable, and serial cable) are secure.
Note: Some unexplained errors may be caused by duplicate IP addresses on
the network. Make sure that your ETS IP address is unique.
Power-up Troubleshooting
Table B-1. Error Messages
Diagnosis/Remedy
Message
Power-up diagnostic failure Note which LED is blinking and its color,
(hardware failure)
then contact your dealer or Lantronix
Technical Support.
Network Error: The ACT
LED will blink yellow 2-3
times per second
A. Make sure the Ethernet network cable is
properly connected and reboot the ETS.
B. If option A fails to resolve the problem,
reload Flash ROM. Refer to D:Updating
Software.
Problem situations and error messages are listed in Table B-2. If you cannot find an
explanation for your problem, try to match it to one of the other errors.
Table B-2. Error Messages
Problem/Message
Error
Remedy
The ETS is connected to
The unit or its power supply Contact your dealer or Lantronix
a power source, but there is damaged.
is no LED activity.
Technical Support for a
replacement.
The ETS is unable to
complete power-up
diagnostics.
This generally indicates a
Note the blinking LED and its color,
then contact your dealer or
Lantronix Technical Support. The
ETS will not be operational until the
fault is fixed.
hardware fault. One of the
LEDs will be solid red for
three seconds, followed by
one second of another
color.
The ETS completes its
power-up and boot
procedures, but there’s
no noticeable serial
activity.
There is a problem with the Check the terminal setup and the
serial connection or the set- physical connections, including the
up of the serial device.
cable pinouts (see C:Pinouts). Try
another serial device or cable, or
cycle power on the ETS.
ETS Installation Guide
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem/Message
Error
Remedy
A rapidly-blinking OK LED
may signal boot failure.
Reboot the unit. When the ETS is
running normally, the OK LED
blinks every two seconds.
The terminal shows a
Boot> prompt rather than
a Local> prompt.
The ETS is not connected
properly to the Ethernet.
Ensure that the ETS is firmly
connected to a functional and
properly-terminated network node.
The ETS Ethernet address
is invalid.
The ETS Ethernet address is
located on the bottom of the unit.
Use the Set Hardware command to
set the correct address, then
reboot. See Entering Commands at
the Boot Prompt on page 50.
Init Noboot command was
entered.
See Entering Commands at the
Boot Prompt on page 50.
The ETS passes power-
up diagnostics, but
attempts to download
new Flash ROM code
from a network host.
If the OK LED blinks
rapidly, the Flash ROM
code may be corrupt.
Reboot the unit. If you get the same
message, you will need to reload
Flash ROM. Refer to D:Updating
Software.
If you did not request a
TFTP boot, the flash ROM
code is corrupt. The unit
will remain in boot mode.
DHCP Troubleshooting
Table B-3. DHCP Troubleshooting
Diagnosis/Remedy
Area to Check
DHCP is enabled on the
ETS
Use the Set Server DHCP Enabled
command. If you manually enter an IP
address, DHCP is automatically disabled.
Make sure the DHCP
server is operational.
Check to see that the DHCP server is on
and is functioning correctly.
The ETS gets its IP
address from the DHCP
server
Refer to the DHCP Manager on your DHCP
server for information about addresses in
use. If the DHCP server doesn’t list your
ETS IP address, there may be a problem.
BOOTP Troubleshooting
If the BOOTP request is failing and you have configured your host to respond to the
request, check these areas:
Table B-4. BOOTP Troubleshooting
Area to Check
Explanation
BOOTP is in your system’s
/etc/services file
BOOTP must be an uncommented line in
/etc/services.
ETS Installation Guide
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Area to Check
Explanation
The ETS is in the
loadhost’s
The ETS must be in this file for the host to
answer a BOOTP or TFTP request.
/etc/hosts file
The download file is in the
correct directory and is
world-readable
The download file must be in the correct
directory and world-readable. Specify the
complete pathname for the download file in
the BOOTP configuration file, or add a
default pathname to the download filename.
The ETS and host are in
the same IP network
Some hosts will not allow BOOTP replies
across IP networks. Either use a host
running a different operating system or put
the ETS in the same IP network as the host.
RARP Troubleshooting
Table B-5. RARP Troubleshooting
Area to Check
Explanation
The ETS name and
hardware address in the
host’s /etc/ethers file
The ETS name and hardware address must
be in this file for the host to answer a RARP
request.
The ETS name and IP
address in the /etc/hosts
file
The ETS name and IP address must be in
this file for the host to answer a RARP
request.
The operating system
Many operating systems do not start a
RARP server at boot time. Check the host’s
RARPD documentation for details, or use
the ps command to see if there is a RARPD
process running.
Entering Commands at the Boot Prompt
If the Boot> prompt appears on the serial console instead of the Local> prompt, one
of two things may be wrong. Either the ETS does not have enough information to
boot, or the network or flash boot has failed. If pressing the Return key does not
display a prompt, press any other key. The Boot> prompt should appear.
If the ETS does not have enough information to boot, or the network or flash boot has
failed, it will print a message to the console and wait ten seconds for serial port
activity. If it detects no serial port activity, it will continue booting provided the flash is
good. However, if the user presses a key during that time period, the ETS will display
the Boot> prompt.
Note: If you see the message “Will attempt another download in x minutes,” press
any key for the Boot> prompt.
A series of commands called Boot Configuration Program (BCP) commands can be
entered at the Boot> prompt to configure the ETS. These commands are a subset of
the entire ETS command set. For example, a typical TCP/IP configuration might use
the following commands:
50
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Figure B-1. BCP Command Examples
Boot> SET IPADDRESS 192.0.1.229
Boot> SET SOFTWARE /tftpboot/ETS*.SYS
Boot> SET LOADHOST 192.0.1.188
Boot> SET SECONDARY 192.0.1.22
Boot> FLASH
% Initialization begins in 5 seconds.....
These commands set the Server’s address, the software loadfile, and the loadhost’s
IP address (as well as that of a backup loadhost). The server then reboots using the
Flash command and will attempt to load the file ETS*.SYS from the host at
192.0.1.188.
Flush NVR
This command is used to restore the ETS’
non-volatile RAM to its factory default
settings. It will reset everything that is
configurable on the server, including the
unit’s IP address.
Flash
This command will force the ETS to
download new operational code and reload
it into Flash ROM. This is necessary when a
new version of software is released and you
wish to upgrade your unit. If the server
cannot download the file, the code in Flash
ROM will still be usable.
Help
Displays a one-page summary of available
commands and what they do.
Init 451
Reboots the ETS after it has been
configured. If the ETS can find and load the
specified software loadfile, it will restart itself
with full functionality. If the loadfile is not
found, the server will attempt to reload
continuously. If there is an error, or if the
console’s Return key is pressed, the ETS
will re-enter the Boot Configuration
Program.
SET BOOTP {Enabled, Disabled}
SET DHCP {Enabled, Disabled}
SET Hardware xx-xx-xx
Enables or disables the sending of BOOTP
queries during the boot sequence. It is
enabled by default.
Enables or disables the sending of DHCP
queries during the boot sequence. It is
enabled by default.
Specifies the last three numbers of the
server’s Ethernet address. The first three
numbers will be supplied automatically.
The Ethernet address should have been set
at the factory. Setting an incorrect address
could cause serious network problems.
SET IPAddress ip_address
SET Loadhost ip_address
Specifies this server’s IP address. Uses the
standard numeric format.
Specifies the host to attempt to load the file
from. The IP address should be in standard
numeric format (no text names are allowed).
ETS Installation Guide
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
SET RARP {Enabled, Disabled}
Enables or disables the sending of RARP
queries during the boot sequence. It is
enabled by default.
SET Secondary ip_address
SET Software filename
Specifies a backup loadhost. The IP address
should be in standard numeric format (no
text names are allowed). The backup
loadhost will be queried if the primary host
cannot load the server.
Specifies the name of the file to load. The
ETS will automatically add .SYS to the
filename you specify. Note that all protocols
must have a filename specified (either the
default or set by the user). For more
information, see D:Updating Software.
TCP/IP users must use the Software option
to specify the loadhost, the loadfile, and their
own network address.
TFTP users can specify a complete path
name (up to 31 characters) if the file is
located in a directory other than the default.
The case of the filename must match that of
the filename loaded onto the host computer.
Show Server
Use this command when issuing other
commands to view the current ETS setup.
52
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
C: Pinouts
Ethernet Connector
Figure C-1. RJ45 Ethernet Connector
RJ45 Serial Connectors
ETS servers are RS-423 compliant, and are thus limited by the equipment at the
remote end of the serial line. If the port is connected to an RS-232 device, it is
subject to RS-232 limits: 15m (50 ft.) in length at 9600 baud, and to 2m (6 ft.) at
115.2K baud, although longer lengths will generally work.
Figure C-2. RJ45 Serial Connector
RJ45 to DB25
If you are connecting an RJ45 port to a DTE device (such as a terminal) that has a
DB25 connector, you will need to use an RJ45-DTE DB25 adapter. To connect an
RJ45 port to a DB25 connector on a DCE device, you will need an RJ45-DCE DB25
adapter. The pinout information for both connections is shown in Figure C-3.
Note: For a full list of adapters, see
ETS Installation Guide
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Pinouts
Figure C-3. Pinouts of RJ45-DB25 Connections
The arrows in Figure C-3 represent the direction of the signal. The pinouts assume
that the 8-conductor cable connecting the ETS and the adapter block is a swapped/
rolled serial cable. Both the transmit and receive ground signals on the ETS
connector are wired to the signal ground on a DB25 adapter.
Figure C-4. RJ45 to DCE DB25 Adapter
You can use a crimper block to connect both transmit and receive grounds from the
RJ45 cable to the single signal ground on the DB25. The connector internally
“splices” the two wires together and provides one wire into the DB25 connector as
shown below.
54
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Pinouts
Figure C-5. Wire Splicer
To splice the wires, cut off the end of the wire that does not extend through the
connector and insert both wires into the connector. Make sure that the wire that does
not extend through the connector is in as far as possible to ensure a solid
connection. Make sure that the wire that does extend through the connector extends
far enough on the other side to be inserted in to the DB25 connector. Carefully
squeeze the connector using a pair of pliers to make sure it is fully latched.
RJ45 to DB9
Figure C-6. RJ45-DTE DB9 Adapter
The arrows in Figure C-6 represent the direction of the signal. The pinouts assume
that the 8-conductor cable connecting the ETS and the adapter block is a
swapped\rolled serial cable. Both the transmit and receive ground signals on the ETS
connector are wired to the signal ground on a DB9 adapter.
The information about crimping the RJ45 ground wires in RJ45 to DB25 applies to
the DB9 connector as well.
ETS Installation Guide
55
Download from Www.Somanuals.com. All Manuals Search And Download.
D: Updating Software
Choosing the Right Software File
Lantronix intends to provide multiple software files for the ETS models. Each
software file will contain the core ETS operating code for that particular model.
Table D-1. Available ETS Software
Software File Name
Models Supported
ETS.SYS
Old, do not use this
file
ETSP.SYS
ETS8P, ETS16PS
ETS16PR
ETS16PR.SYS
ETS32PR.SYS
ETS32PR
Obtaining Software
Current software files (ETS*.SYS) are available on the distribution CD. You can
obtain software updates and release notes for the ETS from the Lantronix World
Internet (ftp.lantronix.com).
Via the Web
The latest version of ETS*.SYS can be downloaded from the Lantronix Web site:
Note: As a result of Netscape Navigator’s configuration, it may try to open
the file as an ASCII text file. To avoid this, hold down the shift key when
choosing the software file.
Via FTP
The ETS software resides on the Lantronix FTP server (ftp.lantronix.com). Most of
these files are binary data, so the binary option must be used to transfer the files. All
released files are in the pub directory. Always download the README file in the pub
directory before downloading anything else; it contains a list of available software
files.
To log into the FTP server, enter a username of anonymous and enter your full email
address as the password. The following text will be displayed:
ETS Installation Guide
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Updating Software
Figure D-1. Sample FTP Login
230-Welcome to the Lantronix FTP Server.
230-
230-IMPORTANT: Please get the README file before
proceeding.
230-IMPORTANT: Set BINARY mode before
transferring executables.
220-
230-Direct questions to [email protected] or
800-422-7044 (US)
230-
230 Guest login ok, access restrictions apply.
Remote system type is [your type will be
displayed here].
ftp>
Reloading Software
The ETS stores software in Flash ROM to control the initialization process, operation,
and command processing. The contents of Flash ROM can be updated by
downloading a new version of the operational software via NetWare, TCP/IP, or
MOP. Regardless of which protocol is used to update Flash ROM, the following
points are important:
‹
‹
‹
‹
‹
The Flash ROM software file name, ETS*.SYS, should not be changed.
The download file should be world-readable on the host.
There is a sixteen character length limit for the path name.
There is a twelve character limit for the filename.
Define commands must be used because Set configurations are cleared
when the ETS boots. Use the List Server Boot command to check settings
before rebooting.
Note: It is important to check ETS settings before using the Initialize Reload
command to ensure that you are reloading the correct software file.
Reloading Sequence
If DHCP, BOOTP, or RARP is enabled on the ETS, the ETS will request assistance
from a DHCP, BOOTP, or RARP server before starting the download attempts. The
ETS will then try TFTP, NetWare, and MOP booting (in that order) provided that it
has enough information to try each download method.
Downloading and rewriting the Flash ROM will take approximately two minutes from
the time the Initialize command is issued. If the download file cannot be found or
accessed, the ETS can be rebooted with the code still in Flash ROM. The OK/ACT
LED will blink quickly while the ETS is booting (and reloading code) and then slowly
when it returns to normal operation.
Note: If you experience problems reloading Flash ROM, refer to
Troubleshooting Flash ROM Updates on page 59.
TCP/IP
Before the ETS downloads the new software, it will send DHCP, BOOTP, and/or
RARP queries (all are enabled by default). Next, the ETS will attempt to download
the ETS*.SYS file using TFTP (Trivial File Transfer Protocol).
Note: EZWebCon can also be used to reload software.
If a host provides DHCP, BOOTP, or RARP support, it can be used to set the ETS IP
address (all methods) and loadhost information (BOOTP and RARP only).
ETS Installation Guide
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Updating Software
Some BOOTP and TFTP implementations require a specific directory for the
ETS*.SYS file. See your host’s documentation for instructions.
To manually configure the ETS IP parameters for software reload, use the following
commands.
Figure D-2. Configuring TCP/IP Reload
Local> SET PRIVILEGED
Password> SYSTEM (not echoed)
Local>> DEFINE SERVER IPADDRESS nnn.nnn.nnn.nnn
Local>> DEFINE SERVER SOFTWARE
“/tftpboot/ETS*.SYS”
Local>> DEFINE SERVER LOADHOST nnn.nnn.nnn.nnn
Local>> LIST SERVER BOOT
Local>> INITIALIZE RELOAD
Note: For instructions on how to log into the ETS to enter these commands, see
the Getting Started chapter.
The path and filename are case-sensitive and must be enclosed in quotation marks.
When attempting to boot across an IP router, you must configure the router to proxy-
ARP for the ETS, or use the bootgateway feature. For more information, see
Set/Define Bootgateway in the Commands chapter of the Device Server Reference
Manual located on the CD-ROM.
NetWare
The ETS*.SYS file should be placed in the login directory on the NetWare file server.
The ETS cannot actually log into the file server (since it knows no
username/password); it can only access files in the login directory itself. On the ETS,
specify the file server name, filename, and path.
Figure D-3. Configuring NetWare Reload
Local> SET PRIVILEGED
Password> SYSTEM (not echoed)
Local>> DEFINE SERVER NETWARE LOADHOST
fileserver
Local>> DEFINE SERVER SOFTWARE
SYS:\LOGIN\ETS*.SYS
Local>> INITIALIZE RELOAD
MOP
The ETS*.SYS filename is the only parameter that the ETS needs to reload via MOP.
Make sure the service characteristic is enabled on the host's Ethernet circuit, copy
the ETS*.SYS file to the MOM$LOAD directory, and reload the ETS using the
Initialize Reload command. Be sure to use binary mode for the file transfer.
58
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Updating Software
Troubleshooting Flash ROM Updates
Many of the problems that occur when updating the Flash ROM can be solved by
completing the following steps:
Table D-2. Flash ROM Troubleshooting
Area to Check
Explanation
NetWare
Ensure the file is in the login directory. Since the ETS
cannot actually log into the file server, it has very
limited access to the server directories.
TFTP
Check the file and directory permissions.
Ensure the loadhost name and address are specified
correctly and that their case matches that of the
filenames on the host system.
Ensure the file and pathnames are enclosed in quotes
to preserve case.
Ensure that TFTP is enabled on the host; several
major UNIX vendors ship their systems with TFTP
disabled by default.
MOP
The Ethernet circuit must have the service
characteristic enabled.
Ensure that the MOM$LOAD search path includes the
directory containing the ETS*.SYS file.
ETS Installation Guide
59
Download from Www.Somanuals.com. All Manuals Search And Download.
E: Specifications
Power Information
Power Requirements
Voltage:
95 - 250 Volts AC, 3-wire single phase, auto-ranging
Frequency:
47-63 Hz
Operating Current:
Power Consumption:
Fuse Rating:
300 mA @ 120 V
40 Watts (maximum)
1.6A, 250 Volts
Power Supply Cord
Cord type:
3 conductors, 1.0 mm2 minimum conductor size
(approximately 18 AWG)
Rated for:
250 Volts AC, 10 Amps
3.0 meters
Length:
Environmental Limitations
Temperature
Operating range:
5° to 50° C (41° to 122° F)
-40° to 66° C (-40° to 151° F)
20° C (36° F)
Storage range:
Max temp. change/hr:
Rapid temperature changes may affect operation. Therefore, do not operate the ETS
near heating or cooling devices, large windows, or doors that open to the outdoors.
Altitude
Operating maximum:
2.4 km (8,000 ft)
9.1 km (30,000 ft)
Storage maximum:
If operating the ETS above 2.4 km (8000 ft.), decrease the operating temperature
rating by 1° F for each 1000 ft.
Relative Humidity
Operating range:
10% to 90% noncondensing, 40% to 60%
recommended
Storage range:
10% to 90% noncondensing
ETS Installation Guide
60
Download from Www.Somanuals.com. All Manuals Search And Download.
F: Frequently-Used Commands
This appendix lists some of the most frequently-used commands of the Multiport
Device Server command set. More information about the command set, including
additional options, can be found in the Device Server Reference Manual located on
the CD-ROM and available for download from
Conventions
Please note the following before continuing:
‹
‹
‹
Commands are divided into Server (general), Port, and Protocol sections.
Within each section, commands are listed alphabetically.
Commands may require privileged user status. Enter Set Privileged, then
enter the privileged password when prompted.
When you enter a Define (or Purge) command, you must reboot the ETS for
the command to take effect. Alternately, you can issue several Set
commands and then a Save command to make the Set commands take
effect without rebooting.
‹
‹
When the abbreviated syntax “{EN/DIS}” is shown, you must choose either
Enabled or Disabled to complete the command.
When 2 is shown as the port number, enter a single port number, a list of
port numbers separated by commas, a range of port numbers separated by
dashes, or the word all.
Server Commands
Table F-1. Frequently-used Server Commands
Command
Option(s)
Description
CONNECT option
servicename
LOCAL num
RLOGIN host
Makes a connection to a LAT service.
Makes a connection to the specified local port.
Makes an Rlogin connection to the specified
host (text name or numeric IP address).
TCP host
Makes a raw TCP connection to the specified
host (text name or numeric IP address).
TELNET host
Makes a Telnet connection to the specified host
(text name or numeric IP address).
DEFINE SERVER BOOTP {EN/DIS}
DEFINE SERVER DHCP {EN/DIS}
Enables or disables querying for a BOOTP host
at system boot time.
Enables or disables querying for a DHCP host
at system boot time.
ETS Installation Guide
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently-Used Commands
Command
Option(s)
Description
DEFINE SERVER GATEWAY ipaddr
Specifies the host to be used as a TCP/IP
gateway to forward packets between networks.
Enter an IP address.
DEFINE SERVER
INCOMING option
BOTH
Enables incoming LAT and Telnet connections.
Enables only incoming LAT connections.
Disables incoming connections.
LAT
NONE
TELNET
PASSWORD
Enables only incoming Telnet connections.
Causes the ETS to prompt for a password for all
incoming connections.
NOPASSWORD
Allows connections to be established without
prompting for a password.
DEFINE SERVER IPADDRESS ipaddr
DEFINE SERVER LOADHOST ipaddr
Sets the ETS’ network IP address.
Specifies the TCP/IP host from which the ETS
requests its run-time code.
DEFINE SERVER LOGIN PASSWORD
Sets a new password that will be required
before incoming logins are accepted. You will be
prompted for the new password (up to 6
alphanumeric characters, case-insensitive).
DEFINE SERVER NAME “newname”
Specifies a new name for the ETS. Names are
restricted in length; generally a name of 11 or
fewer characters is permissible. Enclose value
in quotes to maintain case sensitivity.
DEFINE SERVER NETWARE
LOADHOST server
Specifies the NetWare host from which the ETS
requests its run-time code. Enter a file server
name of up to 11 characters.
DEFINE SERVER PRIVILEGED
PASSWORD
Sets a new password that will be required for
privileged user status. You will be prompted for
the new password (up to 6 alphanumeric
characters, case-insensitive).
DEFINE SERVER RARP {EN/DIS}
Enables or disables querying for a RARP host at
system boot time.
DEFINE SERVER SOFTWARE
“filename”
Specifies the name or path (TCP) of the
software download file. The filename can be up
to 11 characters, and the pathname can be up
to 26. The ETS will add a “.SYS” extension.
DEFINE SERVER SUBNET MASK
ipmask
Specifies the subnet mask to be used for the
ETS. The ipmask must be in n.n.n.n format.
HELP option
<nothing>
<keyword>
Displays a list of top-level (general) Help topics.
Displays information about the keyword(s)
entered. Multiple keywords must be specified in
the order they occur in a command.
DEFINE SERVICE “name” PORT num
Creates a new service and associates it with the
specified port.
DEFINE SERVICE
“name” option
APPLETALK
{EN/DIS}
Toggles whether the named service can be
used to service networks running the specified
protocol. RTEL applies to TCP/IP networks.
LANMAN
{EN/DIS}
LAT {EN/DIS}
NETWARE
{EN/DIS}
62
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently-Used Commands
Command
Option(s)
Description
RTEL {EN/DIS}
DLC {EN/DIS}
DEFINE SERVICE
“name” option
Specifies which service will handle print
requests from DLC hosts. DLC can be enabled
on one service per ETS.
BANNER
{EN/DIS}
When Enabled, causes the ETS to print a
banner page before jobs.
BINARY {EN/DIS} When Enabled, the ETS will not process data
passed through the service. This characteristic
should be enabled when printing PCL data.
EOJ string
Causes the ETS to send an end-of-job string to
the attached device after every job. Enter an
end string or the word none.
FORMFEED
{EN/DIS}
When Enabled, causes the ETS to append a
formfeed to the end of LPR print jobs.
POSTSCRIPT
{EN/DIS}
When Enabled, causes the ETS to assume the
attached device is a PostScript device and act
accordingly.
PSCONVERT
{EN/DIS}
When Enabled, causes the ETS to place a
PostScript wrapper around each job.
SOJ string
Causes the ETS to send a start-of-job string to
the attached device before every job. Enter a
start string or the word none.
DEFINE SERVICE
“name” option
TCPPORT string
Specifies a raw TCP listener socket for the
service. Enter a socket number (4000 to 4999)
or the word none.
TELNETPORT
string
Specifies a TCP listener socket for the service.
Unlike TCPport, this option performs Telnet IAC
interpretation on the data stream. Enter a socket
number (4000 to 4999) or the word none.
INITIALIZE option
DELAY num
Schedules a reboot after num minutes. Enter a
value from 0 to 120.
CANCEL
FACTORY
NOBOOT
Cancels an impending initialization.
Reboots the ETS to its factory default settings.
Forces the ETS to stop in Boot Configuration
Mode rather than fully rebooting.
RELOAD
<nothing>
Forces the ETS to download new operational
code and reprogram its flash-ROM.
LOGOUT option
Logs out the current port (the port that issued
the command).
PORT num
LOCAL
Logs out the specified port.
PURGE SERVICE
option
Removes the definitions of all local services.
Removes the definition of the specified service.
“service”
SET PRIVILEGED
Enters privileged mode, provided the user
enters the proper privileged password when
prompted.
{SHOW/MONITOR} QUEUE
Displays the status of ETS queues once (Show)
or continually every three seconds (Monitor).
{SHOW/MONITOR} <nothing>
SERVER
Displays ETS information once (Show) or
continually every three seconds (Monitor).
ETS Installation Guide
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently-Used Commands
Command
Option(s)
COUNTERS
Description
Displays characteristics related to the various
counters kept by the ETS.
{SHOW/MONITOR} <nothing>
SERVICE option
Displays characteristics about all configured
services once (Show) or continually every three
seconds (Monitor).
“service”
Displays only characteristics related to the
named service.
ZERO COUNTERS ALL
Zeroes all port, node, and server counters.
Zeroes port counters for the specified port.
option
PORT num
Port Commands
In the following commands, “2” can be a single port number, a list of port numbers
separated by commas, a range of port numbers separated by dashes, or the word all.
Table F-2. Frequently-used Port Commands
Command
Option(s)
Description
DEFINE PORT 2
ACCESS option
DYNAMIC
The port can initiate and receive connection
requests.
LOCAL
The port can initiate connection requests, and
local logins are permitted.
NONE
The port is unusable.
REMOTE
The port can receive host-initiated connection
requests.
DEFINE PORT 2 CHARACTER size
Toggles the port between 7-bit and 8-bit
characters (the default). Enter either 7 or 8.
DEFINE PORT 2 DSRLOGOUT
{EN/DIS}
When Enabled, the port will be logged out
automatically whenever DSR is de-asserted.
DEFINE PORT 2 DTRWAIT {EN/DIS}
When Enabled, the ETS will not assert DTR on
the port when it is idle (no user logins or
connections).
DEFINE PORT 2
FLOW option
CTS
Specifies CTS/RTS (hardware) flow control.
{EN/DIS}
Activates or deactivates the currently-configured
flow-control method.
NONE
XON
Removes the current flow control settings.
Specifies XON/XOFF (software) flow control.
DEFINE PORT 2 NAME “newname”
Enter a name of up to 16 alphanumeric
characters for the specified port.
DEFINE PORT 2
PARITY option
parity
Enter even, odd, mark, or space. Specifying
mark or space will change the character size to
7 bits.
NONE
Specifies that no parity will be used (the
default).
DEFINE PORT 2 SPEED baudnum
Sets the port’s baud rate. Acceptable baudnum
values range from 300 to 230000 baud.
64
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently-Used Commands
Command
Option(s)
Description
{SHOW/MONITOR} PORT 2
Displays the port’s configuration characteristics
once (Show) or continually every three seconds
(Monitor). Counters and Status keywords can be
added.
TEST PORT 2
option
COUNT rows
WIDTH cols
Sends an ASCII data stream to the port for the
specified number of rows and/or columns.
POSTSCRIPT
Sends a PostScript test page to the port.
Protocol Commands
In the following table, PROTO is an abbreviation for the optional keyword
PROTOCOL.
Table F-3. Frequently-used Protocol Commands
Command
Option(s)
Description
DEFINE PROTO
APPLETALK option
{EN/DIS}
Enables or Disables the AppleTalk protocol for
the ETS.
ZONE newzone
Places the ETS in a zone other than the default.
DEFINE PROTO IP
option
{EN/DIS}
Enables or Disables the TCP/IP protocol for the
ETS.
GATEWAY ipaddr
See DEFINE SERVER GATEWAY ipaddr.
See DEFINE SERVER IPADDRESS ipaddr.
IPADDRESS
ipaddr
LOADHOST ipaddr See DEFINE SERVER LOADHOST ipaddr.
NAMESERVER
ipaddr
Specifies the IP address of the host that will
resolve text host names into their numeric
equivalents for TCP/IP connection attempts.
DEFINE PROTO
LANMAN option
{EN/DIS}
Enables or Disables the LAN Manager protocol
for the ETS.
DEFINE PROTO LAT {EN/DIS}
option
Enables or Disables the LAT protocol for the
ETS.
LICENSE string
Enables LAT on multi-port ETS device servers.
Enter the license string obtained from Lantronix.
DEFINE PROTO
NETWARE option
{EN/DIS}
Enables or Disables the NetWare (IPX) protocol
for the ETS.
DSCONTEXT
string
Configures the NetWare Directory Services
context in which the ETS is located. For more
information about NDS contexts, see your NDS
documentation.
DSLICENSE string Configures the NetWare Directory Services
license needed to enable NDS on your ETS.
Enter the license string obtained from Lantronix.
DSTREE string
Configures the NetWare Directory Services tree
in which the ETS is located. For more
information about NDS trees, see your NDS
documentation.
DEFINE PROTO
NATIVE
Configures the ETS to use the “native mode”
frame format.
ETS Installation Guide
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently-Used Commands
Command
Option(s)
Description
NETWARE
ETHER_II
Configures the ETS to use Ethernet v2 frame
format.
ENCAPSULATION
option {EN/DIS}
802_2
Configures the ETS to use 802.2 frame format
with NetWare SAPs.
SNAP
Configures the ETS to use 802.2 frame format
with SNAP SAPs.
DEFINE PROTO NETWARE LOADHOST
server
See DEFINE SERVER NETWARE LOADHOST
server.
PURGE
ALL
Removes the entire IP security table.
IPSECURITY option
ipaddress
Removes entries from the IP security table that
are related to the specified IP address.
PURGE PROTO
NETWARE ACCESS
option
ALL
Removes all entries from the NetWare access
list.
server
Removes entries from the NetWare access list
that are related to the specified file server.
{SHOW/MONITOR} PROTO protocolname
Displays operating characteristics of the
specified protocol.
66
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
G: Compliance and Warranty Information
Declaration of Conformity
(according to ISO/IEC Guide 22 and EN 45014)
Manufacturer’s Name & Address:
Lantronix
15353 Barranca Parkway, Irvine, CA 92618 USA
Declares that the product:
Product Name:
Terminal Server
Model Name/Number:
ETS8PS
ETS16PS
ETS16PR
ETS32PR
Conforms to the following standards or other normative documents:
Safety:
EN 60950:1988 + A1, A2
Electromagnetic Emissions:
EN55022: 1998 (CISPR 22, Class A: 1993, A1 1995,
A2: 1996)
IEC 1000-3-2/A14: 2000
IEC 1000-3-3: 1994
Electromagnetic Immunity:
EN55024: 1998 Information Technology Equipment
Immunity Characteristics
IEC 6100-4-2: 1995 Electro-Static Discharge Test
IEC 6100-4-3: 1996 Radiated Immunity Field Test
IEC 6100-4-4: 1995 Electrical Fast Transient Test
IEC 6100-4-5: 1995 Power Supply Surge Test
IEC 6100-4-6: 1996 Conducted Immunity Test
IEC 6100-4-8: 1993 Magnetic Field Test
IEC 6100-4-11: 1994 Voltage Dips & Interrupts Test
(L.V.D. Directive 73/23/EEC)
Supplementary Information:
The product complies with the requirements of the
Low Voltage Directive 72/23/EEC and the EMC
Directive 89/336/EEC.
Manufacturer’s Contact:
Director of Quality Assurance, Lantronix
15353 Barranca Parkway, Irvine, CA 92618 USA
Tel: 949-453-3990
Fax: 949-453-3995
ETS Installation Guide
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance and Warranty Information
Warranty
Lantronix warrants each Lantronix product to be free from defects in material and
workmanship for a period of ONE YEAR. During this period, if a customer is unable
to resolve a product problem with Lantronix Technical Support, a Return Material
Authorization (RMA) will be issued. Following receipt of a RMA number, the customer
shall return the product to Lantronix, freight prepaid. Upon verification of warranty,
Lantronix will -- at its option -- repair or replace the product and return it to the
customer freight prepaid. If the product is not under warranty, the customer may have
Lantronix repair the unit on a fee basis or return it. No services are handled at the
customer's site under this warranty. This warranty is voided if the customer uses the
product in an unauthorized or improper way, or in an environment for which it was not
designed.
Lantronix warrants the media containing its software product to be free from defects
and warrants that the software will operate substantially according to Lantronix
specifications for a period of 60 DAYS after the date of shipment. The customer will
ship defective media to Lantronix. Lantronix will ship the replacement media to the
customer.
In no event will Lantronix be responsible to the user in contract, in tort (including
negligence), strict liability or otherwise for any special, indirect, incidental or
consequential damage or loss of equipment, plant or power system, cost of capital,
loss of profits or revenues, cost of replacement power, additional expenses in the use
of existing software, hardware, equipment or facilities, or claims against the user by
its employees or customers resulting from the use of the information,
recommendations, descriptions and safety notations supplied by Lantronix. Lantronix
liability is limited (at its election) to:
‹
Refund of buyer's purchase price for such affected products (without
interest).
‹
Repair or replacement of such products, provided that the buyer follows the
above procedures.
There are no understandings, agreements, representations or warranties, expressed
or implied, including warranties of merchantability or fitness for a particular purpose,
other than those specifically set out above or by any existing contract between the
parties. Any such contract states the entire obligation of Lantronix. The contents of
this document shall not become part of or modify any prior or existing agreement,
commitment or relationship.
For details on the Lantronix warranty replacement policy, go to our web site at
68
ETS Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|