Engine Cold Weather Kit
Assembly Instructions
Treker 4210/4410ST, 4200/4400ST & 4200/4400NT
Manual No. 701-075M
Tools Required (All Trekers)
• 1/2” Open-end or box-end wrench
• 1/2” Socket and driver
• Straight blade screwdriver
Instructions for Your Vehicle
Before You Start
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
These optional assembly instructions contain only
information required to assemble the Engine Cold
Weather Kit to the Trekers. A detailed Operator’s Manual
was supplied with the Treker. Refer to the Operator’s
Manual for additional specific information especially
information relating to safety concerns. Also included in
the Operator’s Manual is important information on
operation, adjustment, troubleshooting, and
These assembly instructions apply to the Engine
Cold Weather Kit for the following options listed below:
701-074A
701-074A
701-073A
Treker 4210/4410 ST Series
Treker 4200/4400 ST Series
Treker 4200/4400 NT Series
maintenance for this attachment (some manual sections
do not apply to all options).
For a detailed parts list of each assembly kit, see the
bottom of the first page of instructions pertaining to your
vehicle. Use the list as a checklist to inventory parts
received. Please contact your local Land Pride dealer for
any missing hardware.
A separate Parts Manual for replacement parts can be
purchased from your dealer or available free of charge at
handy when placing an order.
Manual Part Numbers:
Further Assistance
• Operator’s Manual (All Series). . . . . . . . . .700-108M
• Parts Manual (4200/4400 NT/ST Series). . 700-108P
• Parts Manual (4210/4410 ST Series) . . . . 700-109P
Your dealer wants you to be satisfied with your new
Engine Cold Weather Kit. If for any reason you do not
understand any part of this manual or are not satisfied
with the service received, the following actions are
suggested:
General Information
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
The Engine Cold Weather Kits listed above are designed
to prevent or eliminate effects of carburetor icing on the
20hp Honda engine used on the Land Pride Trekers.
Carburetor icing may occur at temperatures of
45 degrees Fahrenheit and lower. Typical symptoms will
be loss of power, hard starting, engine backfiring, plug
fouling, gas in the oil or engine stalling. Application of this
kit will force warm air directly into the air intake filter
reducing or eliminating the icing condition and its related
symptoms. Vehicles being started at freezing
temperatures should be allowed an engine and oil warm-
up period of approximately 4-5 minutes prior to full
vehicle operation. When outdoor temperatures are
consistently above 45 degrees Fahrenheit this kit
must be removed or a noticeable power loss will
occur. If plugs have fouled and the dipstick indicates gas
in the oil and an oil overfill condition, the oil and filter must
be changed. Do not overfill with oil or plug fouling will
likely reoccur.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
© Copyright 2005 Printed
11/23/05
■
Manual No. 701-075M
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Assembly Instructions for 4200/4400 ST Trekers
5. Obtain flexible aluminum tube and, taking care not to
deform it, expand the tube to approximately 14”.
Install one end on the heat gathering shield and the
other end on the canister air intake tube.
Assembly Instructions for
4200/4400 ST Trekers
Engine Cold Weather Kit No. 701-074A
General Information
Be sure to read all instructions and safety precautions on
page 1 before installing the Engine Cold Weather Kit.
6. Secure in place with the stainless steel hose clamps
as illustrated.
7. Reinstall the lower access cover to the air intake
canister.
8. Tighten driver’s side canister bolt.
Installation Instructions
Refer to Figure 4:
Air Intake Tube
Before Rotation
1. Release retaining clips two places on bottom of air
cleaner canister and remove air cleaner access
cover.
Driver’s Side
Canister Bolt
NOTE: It is not necessary to disconnect engine
snorkel.
Engine
Snorkel
214547
Figure 5
Air Filter
Intake Tube
Rotated
Engine
Snorkel Hose
SSHose
Clamp
AirCleaner
Canister
Retaining Clip
Access Cover
Flexible
Aluminum Tube
21455
Figure 4
SS Hose
Clamp
Refer to Figure 5:
Muffler Clamp
Flat Bar
2. Loosen driver’s side canister bolt and rotate canister
until air intake tube is facing diagonally toward left
front corner of the engine.
Engine Exhaust
Manifold
Refer to Figure 6:
3. Install heat gathering shield over the engine exhaust
manifold at the 90 degree bend as shown.
Heat
Gathering
Shield
21453
4. Secure with muffler clamp, flat bar, and two nuts.
Figure 6
Treker 4200/4400 ST Series Engine Cold Weather Kit Part No. 701-074A
Qty.
Part No.
Part Description
1
1
1
1
2
701-075M
700-204H
700-267D
700-272D
800-259C
MANUAL - ENGINE COLD WEATHER KIT
HEAT GATHERING SHIELD
MUFFLER CLAMP FLAT BAR
2" FLEXIBLE ALUMINUM TUBE 18.0" LG
HOSE CLAMP WRM DRV#36SS (1.81-2.75)
11/23/05
■
Manual No. 701-075M
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Assembly Instructions for 4200/4400 NT Trekers
5. Obtain flexible aluminum tube and, taking care not to
deform it, expand the tube to approximately 40”.
Install one end on the heat gathering shield and the
other end on the canister air intake tube.
Assembly Instructions for
4200/4400 NT Trekers
Engine Cold Weather Kit No. 701-073A
6. Secure in place with the stainless steel hose clamps
as illustrated.
General Information
Be sure to read all instructions and safety precautions on
page 1 before installing the Engine Cold Weather Kit.
Engine Exhaust
Manifold
Flexible
Aluminum Tube
Muffler Clamp
Installation Instructions
Refer to Figure 1:
Flat Bar
1. Loosen the stainless steel Hose Clamps securing
the rubber air intake hose.
2. Remove rubber air intake hose and save for later
reinstallation when warmer weather prevails.
!
CAUTION!
Caution: Make sure the flexible aluminum tube does not come
into contact with battery terminals. If necessary, secure the
aluminum air intake tube safely away from the battery with a
plastic tie strap.
Heat
Gathering
Shield
SS Hose
Clamp
3. Install heat gathering shield over the engine exhaust
manifold at the 90 degree bend as shown.
21457
4. Secure with muffler clamp, flat bar, and two nuts.
Figure 2
Canister Air
Intake Tube
Flexible
Aluminum Tube
SS Hose
Clamp
SS Hose
Clamp
Battery
Terminals
AirCleaner
Canister
Rubber Air
Intake Hose
AirCleaner
Canister
21127
21456
Figure 1
Figure 3
Treker 4200/4400 NT Series Engine Cold Weather Kit Part No. 701-073A
Qty.
Part No.
Part Description
1
1
1
1
2
701-075M
700-204H
700-267D
700-271D
800-259C
MANUAL - ENGINE COLD WEATHER KIT
HEAT GATHERING SHIELD
MUFFLER CLAMP FLAT BAR
2" FLEXIBLE ALUMINUM TUBE 36.0" LG
HOSE CLAMP WRM DRV#36SS (1.81-2.75)
Manual No. 701-075M
Download from Www.Somanuals.com. All Manuals Search And Download.
■
11/23/05
4
|