HOMEOWNER'S CARE AND
OPERATION INSTRUCTIONS
OASIS SERIES
43" Wood Burning Outdoor Fireplaces
P/N 875,019M REV. B 03/2007
MODELS
LSO-43
LSO-43-H
The information contained in this manual applies to all model fireplaces
identified on this page. This information will help you obtain safe and
dependable service from your Lennox fireplace system. Keep this docu-
ment in a safe place for future reference.
Before you start your first fire, read this Care and Operations Manual
carefully to be sure you understand your fireplace system completely.
Failure to follow these suggestions could result in hazardous operation or
fireplace malfunction, creating a serious potential for personal injury and/
or property damage.
If you have any questions regarding the safe use or operation of your
fireplace, contact your local Lennox Dealer or your contractor/builder.
WARNING: EXERCISE CAUTION WHEN OPERATING YOUR
OUTDOOR FIREPLACE. DO NOT BURN LARGE FIRES.
ATMOSPHERIC CHANGES MAY CAUSE UNEXPECTED
GUSTS OF WIND. FLAMES AND ASHES MAY BE BLOWN
OUT OF THE FIREPLACE. KEEP THE SCREEN CURTAINS
CLOSED AT ALL TIMES.
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
OTL Report No. 116-F-01-2
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Be a knowledgeable wood buyer. There is a
difference in cord sizes. A standard cord stack
of logs is 4 ft. high by 8 ft. long by 4 ft. deep or
the equivalent of this cubic footage, (Figure 1 ).
SOFTWOOD VS HARDWOOD
WARNING: THIS FIREPLACE HAS NOT
BEENTESTEDWITHANUNVENTEDGAS
LOG SET. TO REDUCE THE RISK OF
FIRE OR INJURY, DO NOT INSTALL AN
UNVENTED GAS LOG SET INTO THIS
FIREPLACE.
Softwoods contain about 15 percent highly
flammableresinwhichgeneratescreosotesoot
in the chimney flue. Burning softwood exclu-
sively may not be as desirable nor as safe as
burning denser hardwoods. Many experienced
fire-builders use small amounts of softwood
kindling and newspaper in conjunction with
startingafirewithsplithardwoodlogs.Hereare
some guidelines to remember:
Standard
Cord of
Wood
8'
Prior to installing any gas log set, refer to the
fireplace installation instructions for verifica-
tion of mantle heights and placement of
combustiblematerialsaroundthefireboxopen-
ing. Ventedgaslogsetsdonothaverestrictions
placed upon their BTU rating.
4'
1. Softwoodsproducefastwarmingandshorter
fires. Hardwoods burn less vigorously, have
shorter flames and produce steady, glowing
coals.
4'
Wood Fuel Pointers
2. As a general rule, denser woods contain
morepotentialheatperpound.Mostsoftwoods
offer moderate heat value per pound.
Wood is a wonderful renewable fuel source.
Normally it burns clean, leaving only a mini-
mum of waste ash, provides comforting heat
and can provide a variety of aromas and visual
images.
Figure 1
A face cord is the same height and length as a
standard cord but the depth is only the length
of the logs (12, 18 or 24 inches). A face cord
can contain as little as 25% of the wood found
in a standard cord.
3. Differentwoodsvarywidelyinflameheights,
flame intensities, smoke characteristics and in
sparking. Most hardwoods do not spark.
You will want to know which woods are best for
use. Sometimes you may want a quick, short
fire to offset a morning chill. Soft woods are
preferable in this case. Other times you would
want more slow burning and a uniform heat
output. Hardwoods are preferable for this use.
4. Most freshly cut “green” wood will not burn
well and will smoke. Green wood can be from
10 to 40 percent less efficient than air-dried
seasoned wood.
If you buy by the ton, remember that wood
becomes lighter as it dries. When buying green
or wet wood, ask for some extra poundage to
allow for the extra water you will be getting.
5. Moisture and resin found inside unseasoned
wood cells will build up pressure under heat
and explode as sparks.
The amount of heat available from the logs will
be about equal on a weight basis. However,
logs are generally not weighed so the amount
of heat will depend on:
9. When comparing woods of the same mois-
ture content and same species, we find most
woods have approximately the same heating
potential per pound.
6. Most wood needs to be seasoned 9 to 12
months to reduce the moisture content and
produce good steady fires. When moisture
content is reduced from 60 to 20%, the gain in
heat potential is nearly 7%.
1. The type of wood used.
2. How dry it is.
3. How many logs you put in.
4. The size of the logs.
However, most wood is sold by volume, not by
weight. To determine the best heating source,
look at the density of various wood types.
(Density is the weight for a given size.) The
higher the density, the more potential heat
output. A standard cord has a volume of 128
cubic feet. This figure also includes the air
space between and around the wood. The ac-
tual volume in a standard cord is between 60
and 100 cubic feet; depending on how tightly
the wood is packed.
7. Proper storage of wood, especially during
seasoning, is essential. We recommend that
you:
The last statement means that one big log
weighing 10 pounds has as much heating po-
tential as 10 pounds of twigs. However, air
cannot get at the solid log to feed the fire so the
solid log will burn slowly. While you would get
the same amount of heat out of either fire, the
smaller the pieces of wood and the more air
space around them, the faster the fire will burn.
a. Never store wood on the ground. This will
causerottingandinsectinfiltration.Raisewood
on flat rock or scrap wood.
b. Stack wood loosely to allow air circulation.
Assumingthatyouarecomparingtwostandard
cords of different species but the same volume
and moisture content, the denser species will
providemoreBTU’s.Thetableofwoodspecies/
densities reveals more helpful guidelines.
DISPOSAL OF ASHES
c. Store wood where it will not be excessively
exposed to weather, such as under a tarp or
under a roof.
Ashes should be placed in a metal container
with a tight fitting lid. The closed container of
ashes should be placed on a noncombustible
floor or on the ground, well away from all
combustible materials, pending final disposal.
If the ashes are to be disposed of by burial in
soilorotherwiselocallydispersed, theyshould
be retained in the closed container until all
cinders have thoroughly cooled.
d. Do not stack wood directly against the walls
of your home.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Periodical inspection and cleaning may be
required. See Figure 2 and follow the instruc-
tions below for removal and installation:
HARDWOODS
DENSITY
Alser, Red
Ash
Aspen
Basswood, American
Beech, American
Birch
.41
1. With a flat screw driver, press on the re-
tainer bracket and pull the strainer downwards
to release.
.49-.60
.38-.39
.37
.64
.55-.65
.38
2. Clean or discard the strainer if damaged.
Butternut
Cherry, Black
Chestnut, American
Cottonwood
Elm
Hackberry
Hickory, Pecan
Hickory, True
Honey locust
Locust, Black
Magnolia
.50
.43
3. Reinstall or replace the flue strainer.
.34-.40
.60.63
.53
.60.66
.69-.75
.66 (est.)
.69
.48-.50
.48-.63
.59-.67
.64-.88
.42
Flue Strainer
Fireplace Air Inlet
Must Be Free Of
Any Obstructions
Maple
Oak, Red
Oak, White
Poplar
Figure 3
Retainer Bracket
REFRACTORIES
Sassafras
.42
Sweet gum
Sycamore, American
Tanoak
Tupelo
Walnut, Black
Willow, Black
.52
.49
.64 (est.)
.50
.55
All fireboxes contain a furnace refractory floor,
sides and back. These refractories are rein-
forcedwithsteel,butcanbebrokenbyimproper
use. Dropping logs on the bottom refractory
and building fires directly against the refracto-
ries can cause premature burnout of these
components. It may easily be repaired or re-
placedatcostsfarbelowrepairandmaintenance
for masonry fireplaces.
Figure 2
REINSTALLING OR REPLACING THE FLUE
STRAINER (P/N LB-101309)
.39
1. Hang the retaining brackets on the outer-
most screws inside the firebox at the back,
near the flue inlet.
SOFTWOODS
DENSITY
Bald cypress
Cedar
Douglas Fir
Fir
Hemlock
Larch, Western
Pine
Redwood
Spruce
.46
.31-.47
.46-.50
.32-.43
.40-.45
.52
.39-.59
.35-.40
.35-.41
.53
2. Place one side of the flue strainer, wedged
between the front screws and the top, inside
the firebox.
Proper care and “burn-in” of the firebox will
prolong the period of enjoyment without exten-
sive maintenance. For the first few uses, build
small fires – not roaring infernos. The materials
used in the refractories contain and absorb mois-
ture. It is important to “cure” the refractories by
building only modest fires. Under normal usage,
itisexpectedthathairlinecrackswillappearinthe
refractory surface. These hairline cracks do not
affect the safe operation of the fireplace.
3. With the aid of a flat screw driver, push
upwardsontheoppositeendofthefluestrainer
against the retainer brackets, (one at a time)
until it snaps to its locking position.
Tamarack
AIR INLET
DAMPER
This appliance requires the installation of an
air inlet for proper operation.
Note: This appliance does not have a damper.
A flue strainer has been provided to prevent
any debris from entering into the chimney.
STARTING A FIRE
The fireplace draws air into the chimney and
firebox chambers through the air inlet to cool
the firebox during operation.
Note: Caution must be observed when operat-
ing this fireplace under windy conditions. Do
Not burn large fires, as flames may be drawn
outofthefirebox. Ifthisoccurs, closetheglass
doorsimmediately. Ifnotequippedwithdoors,
extinguish the fire or keep it to a minimum if
safe. The screens must be closed at all times
whileinoperation,exceptwhenfeedingthefire.
FLUE STRAINER
The flue strainer is a wire cloth attached to the
flue entrance to prevent debris from entering
the chimney.
It is important to inspect the air inlet and free
it from any obstruction before operating the
fireplace (see Figure 3 ).
WARNING: DO NOT OPERATE THE FIRE-
PLACE UNLESS A COMPLETE AIR INLET
SYSTEM HAS BEEN INSTALLED.
1. To start a fire in the fireplace properly, first
check that the flue strainer is clear and the air
inlet is unobstructed.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. The grate in the firebox should be centered
on or over the bottom hearth so your fire can
breath properly. Crumble and twist plenty of
newspapers UNDER the grate and criss-cross
some small dry kindling sticks on top of the
paper or on the bottom of the grate.
IMPORTANT: Thelacquer coatingonthepol-
ished brass glass doors and trim pieces can
be damaged or removed causing corrosion
and/or tarnish. Do not remove the protective
lacquer coating from plated polished doors
and trim. To help protect the finish; use a
non-acidic wax and avoid the over-spray of
acidic/alkali based glass cleaners on the
brass pieces. Please understand that the
heat of the fire will cause the protective
lacquer finish to slightly change to a light
caramel color. Do not be alarmed as this is
a normal occurrence.
Care and Cleaning of Your Glass Doors
Never clean the glass when the doors are hot.
Do not use ammonia or ammonia based glass
or household cleaner to clean the glass or the
door frame. An ammonia based cleaner will
damage the finish of the glass door.
3. Build a pyramid of three split logs (split will
start much faster). Arrange the uneven wood to
provide plenty of air space between.
Cleantheglassdoorsbywipingwithadamptowel
followed by a clean dry towel to remove streaks.
4. When lighting your fire, a little smoke may
escape – more likely if the chimney is cold. To
correct this, hold a lighted newspaper up inside
the firebox near the chimney opening. This will
turn around any downdraft and clear the flue of
cold air. As your log fire burns below, the
updraft will improve as the chimney heats up.
Remove stubborn stains from the glass with a
mild soap solution and a towel dampened with
clean water. Dry with a clean dry towel.
MAINTENANCE GUIDELINES
• The fire must always be confined within the
boundaries of the fuel grate.
Your fireplace is designed to operate trouble-
free with minimum maintenance. However, like
any fine appliance, it deserves and requires
some housekeeping attention.
• The fireplace screens must always be closed
whenever the fireplace is being used.
5. Now, light the paper at both sides of the
firebox.
• Never slam the glass door since it could cause
the glass to break.
Your fireplace will perform better – and cer-
tainly look more attractive to family and friends
– if it is cleaned before each use. Before the first
seasonal use in Autumn and after the last fire in
Spring, it is important to inspect the fireplace
system carefully. We recommend at least two
complete fireplace inspections a year.
6. Close the screens to prevent the escape of
sparks and embers.
• Do not build excessively large or hot fires —
scorching or discoloring of the plated brass
trim may occur.
GLASS DOOR OPERATING SAFETY
PRECAUTIONS AND INSTRUCTIONS
These fireplaces may be equipped with glass
doors. Refer to the end of this document for a
listing of the glass doors approved for use with
these fireplaces.
•Extremetemperaturechangescancauseglass
breakage—donotbuildahotfireandclosethe
glass doors if the doors are cold.
Before Each Use
1. Clean the firebox of excessive ashes. Some
owners prefer to leave a small layer to insulate
the cold refractory below the grate which helps
fire starting.
•Ifthetemperedglasspanebecomesscratched
or chipped, it creates a weakness in the glass
whichcancausetheglasstobreakwhenheated.
Replace the pane of glass by contacting your
nearest dealer.
WARNING: IF YOUR FIREPLACE IS
EQUIPPED WITH GLASS DOORS, IT
SHOULDBEOPERATEDWITHTHEDOORS
FULLY OPEN OR FULLY CLOSED. IF THE
DOORSARELEFTPARTIALLYOPEN, GAS
AND FLAMES MAY BE DRAWN OUT OF
THEOPENING, CREATINGRISKSOFBOTH
FIRE AND SMOKE. SEE FIGURE 4 FOR
PROPER OPERATING CONDITIONS.
This fireplace has a factory supplied grate at-
tached, it is permissible to remove the grate for
cleaning; however, the grate must be re-at-
tached to the fireplace before the next burn.
CAUTION: GLASS AND METAL FRAMES
GET HOT — ALWAYS USE HANDLES TO
OPEN AND CLOSE THE DOORS.
2. Keep the fireplace screens clean so combus-
tion air flows freely.
WARNING: BE AWARE THAT SAFETY
GLASS IS UNPREDICTABLE WHEN HOT
ANDMAYBREAK, EXPELLINGHOTGLASS
INTO THE ROOM. ADVISE ALL FAMILY
MEMBERS TO REMAIN WELL AWAY
FROM THE FIREPLACE WHEN OPERAT-
ING WITH DOORS CLOSED TO AVOID
ANY POSSIBLE PERSONAL INJURY.
3. Spot check the brick-like refractory for small
cracks. Heat from the fire expands it slightly.
When it cools, it contracts.
Refractories should be replaced when:
1. The crack opens more than ¹⁄₄" (19 mm).
IMPORTANT: Plated polished brass glass
doors may have a plastic covering over all
brass pieces for protection during shipping
and handling. The plastic covering should be
removedbeforeinstallationoftheglassdoors.
Under the plastic covering is a protective
lacquercoatingwhichshouldnotberemoved.
In some instances, if it is removed, irrevers-
ible damage to the brass finish could occur.
Refertothefollowingforspecificinformation
on plated polished brass.
2. Pitting in the surface is extensive and pits
become deeper than ³⁄₁₆" (4.76 mm).
Glass Doors
Fully Open or
Fully Closed
3. Any piece of refractory larger than 2" (51 mm)
in radius and ³⁄₁₆" deep becomes dislodged.
(Bi-Fold Doors)
Figure 4
If conditions 1, 2 or 3 occur, the refractory
should be replaced.
CAUTION: IF A SMOKING CONDITION EX-
ISTS, GLASSDOORSSHOULDBECLOSED
DURING FIREPLACE OPERATION.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TWICE A YEAR CHECK-UP
CLEANOUT PANEL (DOOR SUPPORT
FRAME)
CREOSOTE FORMATION AND REMOVAL
Normally, twice a year, you should inspect
your fireplace following this list:
When wood is burned slowly, it produces tar
and other organic vapors, which combine with
expelled moisture to form creosote. The creo-
sote vapors condense in the relatively cool
chimney flue of a slow-burning fire. As a
result, creosote residue accumulates on the
flue lining. When ignited, this creosote makes
an extremely hot fire.
The Cleanout Panel provides an outlet for
water that may enter the fireplace during rain-
ing or melting snow. Therefore it is important
to keep it clear from ashes and debris.
1. Inspect the opening in your chimney top
and remove any debris that could clog it. The
cap is usually held in place by four (4) screws,
which remove easily for checking or cleaning
the full length of the flue from above. Remove
the chimney top while wearing gloves to guard
against any sharp metal edges.
Remove the Cleanout Panel by removing the
screw at each end and lift (see Figure 5 ).
Check inside and clean if necessary.
The chimney should be inspected at least
twice yearly during the heating season to de-
termine if a creosote build-up has occurred.
Make sure the area is free of any debris and
reattach the panel with the screws previously
removed.
2. Inspect the entire flue from the top down for
obstructions such as birds nests, leaves, etc.
This may be done by using a flexible handled
chimney cleaning brush. If the chimney con-
tainsoffset/returnelbows;asoftbrushcleaning
from the top down to any elbow and then from
the firebox up to the offset/return section is the
proper method. The beam from a powerful
flashlight will help in this inspection, (removal
of the flue strainer may be needed).
If creosote has accumulated, it should be
removed to reduce the risk of a chimney fire.
Note: The hearth area can be vacuum cleaned.
Larger debris must be removed manually. It is
recommended to clean the hearth area while
the cleanout panel is removed to make sure
that no ashes will fill the cleanout panel area
upon reattachment.
Ifcreosotebuild-upisfound,donotusechemi-
cal chimney cleaners that are poured on a hot
fire. The chemical cleaners can be dangerous
and generally only work on the flue section
nearest the fire, leaving the rest of the flue
unaffected. It is best to take the time to clean
the flue as previously described or have the
chimney professionally cleaned by a qualified
chimney sweep.
3. Look up from inside the fireplace to see if
any obstructions are in the lower flue area. If
present, shut the glass doors (if installed) to
seal the firebox and contain any soot that
might fall.
TROUBLESHOOTING
Screw
If your fireplace does not have glass doors
installed, a damp sheet covering the fireplace
opening and sealed with masking tape will do.
Then clean the flue from the top down (if an
offset system, clean per Step 2) using a proper
size chimney brush with flexible pole sections.
Don’t open the doors or remove the sheet until
all soot has settled. Vacuum, don’t sweep.
Cleanout Panel
Screw
Note: "Smoke Free" operation is not warranted
nor are we responsible for inadequate system
draft, general construction conditions, inad-
equate chimney heights, adverse wind condi-
tions and/or unusual environmental factors or
conditions beyond our control.
Figure 5
Stainless Steel Outdoor Weather Cover
(P/N H0321)
If you do experience a problem, here are sev-
eral things to check:
An optional Stainless Steel Outdoor Weather
Cover can be purchased to provide additional
protection against leaves and other objects
that wind can carry which can accumulate
inside your fireplace or damage your fireplace
Glass Doors. Complete instructions for use
are provided with the cover.
Note: Removal of the flue strainer may be
requiredtoclearany obstructionsinsidetheflue.
1. Remember – always check to ensure that
the flue strainer and air inlet are clear from
obstructions before lighting a fire!
4. Check the metal flashing and seals around
your chimney. Seal any cracks or loose nail-
head openings to prevent roof leaks.
2. Is your fire too far forward? Move it toward
the back with your poker. Keep the fire well
within the confines of your fuel grate.
WARNING: CONTINUED OVERFIRING
CAN PERMANENTLY DAMAGE YOUR
FIREPLACE SYSTEM. SOME EXAMPLES
OF OVERFIRING ARE:
5. Clean the firebox thoroughly by using a soft
brush or equivalent.
3. Keep your fire up on the grate and the refrac-
tory below free of excessive ashes. The fire
needs plenty of air movement around the logs.
6. Check outside air inlet and free from any
obstructions.
• BURNING QUANTITIES OF SCRAP
LUMBER, PINE BRANCHES, PAPER OR
CARDBOARD BOXES WHICH EXCEED
THEVOLUMEOFTHENORMALLOGFIRE.
7. Exposed stainless steel face may be cleaned
with a solution of baking soda and water:
4. Is a breeze or wind blowing? This can cause
negative pressure and an unwanted downdraft
– and smoking.
Mix a tablespoon of baking soda in a cup of
water and spray on the exposed stainless steel
face. Wipe with a clean cloth.
• USE OF ARTIFICIAL WAX BASE LOGS,
TRASH OR OTHER CHEMICALS OR
CHEMICALLYTREATEDCOMBUSTIBLES.
5. Is your wood fuel too wet or unseasoned?
Or does it contain some chemical substance
that causes sputtering, smoking and toxic
fumes?
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Figure 6 illustrates the correct height of
yourchimneytop. Itisunlikelythatyourinstal-
lation does not adhere to the installation
instructions. However, if not correct, you
could experience an unusual downdraft. Usu-
ally,thebestsolutionistoincreasethechimney
height. This may also be necessary if nearby
trees, adjoining roof lines or a hill is causing a
downdraft condition.
7. Remember, your fireplace has been de-
signed as a decorative, supplemental heating
device only, it is not intended for heating
purposes.
ACCESSORY COMPONENTS
Less than
10' (3m) To
Roof Peak
10' (3m)
FTF10-CT1
Bi-Fold Doors
H0329
43LBFOD-BS
2' (610mm)
Min.
3'
3'
(914mm)
2' (610mm)
(914mm)
Bi-Fold Doors
Min.
Min.
Min.
Your fireplace can be fitted with beautiful bi-
fold doors. These doors are easily fitted to the
fireplace opening. Model LBFOD-BS doors
have the striking look of brushed steel.
To ensure warranty and to prevent a potential
fire hazard, do not use any other doors on
these appliances.
Figure 6
WARRANTY
This fireplace is covered by a limited warranty detailed separately from this document.
Retain this manual. File it with your other documents for future reference.
PRODUCT REFERENCE INFORMATION
We recommend that you record the following important information about your fireplace. Please
contact your Lennox dealer for any questions or concerns. For the number of your nearest Lennox
dealer, please call 1-800-9-LENNOX
Your Fireplace's Model Number _______________________________________
Your Fireplace's Serial Number ________________________________________
The Date On Which Your Fireplace Was Installed __________________________
Your Dealer's Name_________________________________________________
Outdoor Weather Cover
H0321
43L-ODC
When ordering repair parts, always give the
following information:
REPLACEMENT PARTS
Stainless Steel Outdoor Weather Cover
A complete parts list is found at the end of this
manual. Use only parts supplied from the
manufacturer.
Your fireplace can be fitted with an attractive
Stainless Steel Outdoor Weather Cover. This
cover is easily fitted to the fireplace opening.
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
Normally, all parts should be ordered through
your Lennox dealer. Parts will be shipped at
prevailing prices at time of order.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
LSO-43
Part No. Qty.
LSO-43H
No.
DESCRIPTION
Part No. Qty.
Fireplace Assembly
H0303
35M0901
LB-101301
16M31
1
2
2
1
–
1
–
1
–
1
1
1
1
1
1
1
1
2
H0304
35M0901
LB-101301
–
1
2
2
–
1
–
1
–
1
1
1
1
1
1
1
1
1
2
1.
2.
3.
Firescreen
Rod, Screen
Refractory, Side, Right (Traditional)
Refractory, Side, Right (Herringbone)
Refractory, Side, Left (Traditional)
Refractory, Side, Left (Herringbone)
Refractory, Rear (Traditional)
Refractory, Rear (Herringbone)
Refractory Base
–
16M39
4.
5.
16M31
–
–
16M40
16M34
–
–
16M42
6.
7.
16M36
16M44
Grate
LB-97144
LB-97044
LB-97045A
LB-97045B
LB-97037
LB-97046
LB-101309
LB-101340
LB-97144
LB-97044
LB-9704A
LB97045B
LB-97037
LB-97046
LB-101309
LB-101340
8.
Frame, Front Lower
9.
Frame, Side L.H.
10.
11.
12.
13.
14.
Frame, Side R.H.
Frame, Door Support (Cleanout Panel)
Frame, Top
Flue Strainer
Retainer Bracket (Flue Strainer)
14
12
13
5
4
9
10
1
8
3
2
11
6
7
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Lennox reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2002 by LENNOX
1110 West Taft Avenue
Orange, CA 92865
P/N 875,019M REV. B 03/2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|