HD225
HDTV Projector
Users Manual v1.1
Download from Www.Somanuals.com. All Manuals Search And Download.
3
TABLE OF CONTENTS
Introduction
5
Positioning the projector
Video connections
6
7
Connecting a video device
Displaying a video image
Connecting a computer
Shutting down the projector
Troubleshooting your setup
Using the keypad buttons
Using the remote control
Using the audio
Customizing the projector
Optimizing video images
Using the menus
Picture menu
Settings menu
7
9
10
11
11
15
15
16
16
17
17
18
21
23
23
23
25
25
26
26
Maintenance
Cleaning the lens
Replacing the projection lamp
Cleaning the dust filters
Using the security lock
Red LED behavior and projector errors
Projected image size
If you are experienced in setting up presentation systems, use the included Quick Set Up card.
For complete details on connecting and operating the projector, refer to this User’s Guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Important Operating Considerations for Safety
• Place the projector in a horizontal position
with no greater than 8-degrees forward or
backwards tilt.
• Locate the projector in a well-ventilated
area without any obstructions to intake or
exhaust vents. Do not place the projector on
a tablecloth or other soft covering that may
block the vents.
• Locate the projector at least 4' (1.2 m) away
from any heating or cooling vents.
• Use only Knoll-approved ceiling mounts.
The minimum distance between the ceiling
and a ceiling-mounted projector is 11.8”/30
cm.
• Use only the power cord provided. A surge-
protected power strip is recommended.
• Refer to this manual for proper startup and
shutdown procedures.
• In the unlikely event of the lamp rupturing, discard any edible items placed in the surrounding
area and thoroughly clean the area along all sides of the projector.
•Wash hands after cleaning the area and handling the ruptured lamp. This product has a lamp
that contains a very small amount of mercury. Dispose of it as required by local, state or federal
Follow these instructions to help ensure image quality and lamp life over the life of the projector.
Failure to follow these instructions may affect the warranty. For complete details of the warranty,
see the Warranty section at the end of this User's Guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Introduction
Your new Knoll HD225 projector from
Knoll Systems is specifically designed
for home cinema applications. It has
native 1280x720 resolution. The
projector is easy to connect, easy-to-
use, and easy to maintain.
*The lens cap tether ships in the Documentation Pack. Attach it to the lens cap and
the projector if desired.
Connector Panel
The projector provides two computer and
four video connectors:
• one M1-D/A (HD, DVI, and computer)
• one VESA (HD, HD component, and
computer)
• one S-video
• one composite RCA
• one component video
It also has an RS-232 serial connector for
serial control. The Command Line
Interface (CLI) specifications and
commands are on our website.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
A 3.5mm mini-jack trigger provides 12-
volt current. This provides a constant
output while the projector is on. For
example, if you connect your projection
screen to the trigger, when you turn on
the projector the screen will move down;
when you turn the projector off, the
screen will return to the storage position.
You must turn the trigger on in the
System menu, see page 21.
Positioning the projector
There are a number of factors to consider when determining where to set up
the projector, including the size and
shape of your screen, the location of
your power outlets, and the distance
between the projector and the rest of
your equipment. Here are some
general guidelines.
1 Position the projector on a flat
surface at a right angle to the screen.
The projector must be within 10 feet
(3 m) of your power source. To
ensure adequate cable access, place
the projector at least six inches
(0.15m) from a wall or other objects.
Place the projector at least 5.6 feet
(1.7 m) from the projection screen.
If you install the projector on the
ceiling, refer to the installation guide
that comes with the Ceiling Mount Kit
for more information. To turn
the image upside down, see page 21.
Knoll recommends use of an
authorized Knoll ceiling mount. The
Ceiling Mount Kit is sold separately.
2 Position the projector the desired
distance from the screen.
The distance from the lens of the projector to the screen, the zoom setting, and the video format
determines the size of the projected image. For more information about projected image sizes,
see page 26.
The image exits the projector at a given angle. This image offset is 105%. This means that if you
have an image 10’ high, the bottom of the image will be 0.5’ above the center of the lens.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Video connections
You can connect VCRs,
DVD players, camcorders,
digital cameras, video
games, HDTV receivers,
and TV tuners to the
projector. (You cannot
directly connect the coaxial
cable that enters your
house from a cable or
satellite company; the
signal must pass through a
tuner first. Examples of
tuners are digital cable
boxes, VCRs, digital video
recorders, and satellite TV
boxes.
Basically, any device that
can change channels is
considered a tuner.) If there
is more than one output,
select the highest quality
one. DVI, Component video
and RGB (M1, HD15) have
the best quality, followed by
S-video, and then
composite video.
Input signal Connector
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Connecting a video device
If your video device has more than one output, select the highest quality one. DVI video has the
best quality, followed by component video, S-video, and then composite video. If the video device
uses component cable connectors, plug the cable’s green connectors into the green component-
out connector on the video device and into the green component connector (labeled “Y”
Component 3) on the
projector. Plug the component
cable’s blue connectors into the
blue component-out connector
on the video device and into the
blue component connector
(labeled “Pb”) on the projector.
Plug the component cable’s
red connectors into the red
component-out connector on
the video device and into the
red component connector
(labeled “Pr”) on the projector.
If you are using RGB input, plug
the additional connector into the
Video 5 connector and turn on
the RGB Video option in the
Sources menu. See page 21. If
the video device uses a round,
four-prong S-video connector,
plug the S-video cable into the
S-video connector on the video
device and into the S-video 4 connector on the projector. Connect the red and white audio
connectors from the A/V cable to your source and Audio In connector on the projector, if desired.
If the video device uses a
yellow composite video
connector, plug the A/V
cable’s yellow connector into
the video-out connector on the
video device. Plug the other
yellow connector into the yellow Video 5 connector on the projector. Connect the red and white
audio connectors from the A/V cable to your source and the projector. If the video device uses a
DVI connector, plug the computer cable into the video-out connector on the video device. Plug
the other connector into the DVI 2 connector on the projector. If the video device uses a VESA
connector, plug a VESA cable into the video-out connector on the video device. Plug the other
connector into the VESA 1 connector on the projector.
Connecting the power cable
Connect the power cable to the
connector on the back of the
projector and to your electrical
outlet. The Power button on the
keypad lights up and the LED on the keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector.
on projector
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Displaying a video
image
Remove the lens cap.
Press the Power button on
the top of the projector or
the remote.
The fans start to run. When
the lamp comes on, the
startup screen is displayed.
It can take a minute for the
image to achieve full
brightness.
? No startup screen? Get help on page 11.
Plug in and turn on the video
device.
The video device’s image should appear on the projection screen. If it doesn’t, press the Source
button on the keypad or remote.
Adjust the height of the
projector by pressing the
release button to extend
the elevator foot. Rotate the
leveling foot, if necessary.
Position the projector the desired
distance from the screen at a 90-degree
angle to the screen. See 26 for a table
listing screen sizes and distances to the
screen.
Adjust the zoom or focus rings by
rotating them until the desired
image size and focus are produced.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
If the image is not square, adjust the vertical keystone using the buttons on the keypad.
Press the upper Keystone button
to reduce the upper part of the
image, and press the lower
Keystone button to reduce the
lower part. You can also adjust
the horizontal keystone via the
menus, or set the projector
to automatically adjust the vertical keystone. See page 17 .
Adjust the volume in the Audio menu.
Adjust the Contrast, Brightness, Color,
or Tint in the Picture menu.
See page 18 for help with the menus.
Connecting a computer
Connect either a VESA cable or M1 cable into
the appropriate connector on the projector
(Vesa 1 or DVI 2). Connect the other end to
the video port on your computer. If you are
using a desktop computer, you first need to
disconnect the monitor cable from the
computer’s video port.
Connect the black power cable to the
connector on the back of the projector and to
your electrical outlet. The Power LED on the
projector’s keypad turns solid green.
NOTE: Always use the power cable that
shipped with the projector.
You can control the projector from an LCD
control panel or computer by connecting an
RS-232 cable to the projector’s Serial control
connector.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Shutting down the projector
The projector automatically blanks the
screen after no active source is
detected for 30 minutes. This blank
screen helps preserve the life of the
projector.
The image returns when an active source
is detected or a remote or keypad button
is pressed.
Screen Save
You can make the blank screen appear
after five minutes by turning on
Screen Save in the Settings>System
menu. See page 22. There are six time
options for the Screen Save feature.
They range from five minutes to 30
minutes with five-minute intervals.
Power Save
The projector also has a Power Save
feature that automatically turns the lamp
off after no signals have been detected
for five minutes. After three additional
minutes with no signal, the projector
powers down. If an active signal is
received before the projector powers down, the image is displayed. You must press the Power
button to display an image after 30 minutes have passed. When Power Save is enabled, Screen
Save is disabled. See page 22.
Turning off the projector
To turn off the projector, press the Power button. You can cancel the shutdown by pressing the
power button again within 3 seconds. The lamp turns off and the LED blinks green for one minute
while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights green
and the fans stop. Unplug the power cable to completely power off the projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Still having problems?
If you still need assistance, visit our website or call us. See the inside of the back cover for
support contact information. This product is backed by a limited warranty. When sending the
projector in for repair, we recommend shipping the unit in its original packing material, or having a
professional packaging company pack the unit. Please insure your shipment for its full value.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Using the keypad buttons
Most buttons are described in
detail in other sections, but here
is an overview of their
functions:
power–turns the projector on
(page 9) and off (page 11).
menu–opens the on-screen
menus (page 17).
select–confirms choices made in the menus (page 17).
up/down arrows–navigates to and adjusts settings in the menus (page 17).
auto image–resets the projector to the source.
presets–cycles through the available preset settings (page 19).
keystone–vertical keystone adjusts the squareness of the image (page 18).
brightness–adjusts intensity of the image (page 18).
resize–changes the aspect ratio (page 18).
source–changes the active source (page 9).
Using the remote control
The remote uses two provided AAA batteries. They are easily installed
by sliding the cover off the remote’s
back, aligning the + and - ends of the
batteries, sliding them into place, and
then replacing the cover.
To operate, point the remote at the
projection screen or at the projector
(not at the video device or computer).
The range of optimum operation is up
to 30 feet (9.14m).
Press the remote’s Menu button to
open the projector’s menu system.
Use the arrow buttons to navigate, and
the Select button to select features
and adjust values in the menus. See
page 15 for more info on the menus.
The remote also has:
• Power button to turn the projector on and off (see page 11 for shutdown info)
• Backlight button to light the remote’s buttons in the dark
• Brightness and Contrast buttons to adjust the image
• Blank button to display a blank screen instead of the current image (to change the color of the
blank screen, see page 21)
Download from Www.Somanuals.com. All Manuals Search And Download.
16
• Source buttons to switch among sources (to assign a particular source to a source button, see
page 21) and a source toggle
• Resize button to change the Aspect Ratio (see page 18)
• Auto Image button to resynchronize the projector to the source
• Preset button to restore stored settings (see page 19)
• Overscan button to remove noise in a video image (page 19)
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are not dead.
• Make sure you’re pointing the remote at the projector or the screen, not at the video device or
the computer, and ensure you are within the remote range of 30 feet (9.14m).
Using the audio
To play sound from the projector,
connect your source to the
Audio In connector on the
projector.
To adjust the volume, mute or
turn off the projector’s chime, use
the Audio menu (see page 16).
Troubleshooting audio
If there is no sound, check the following:
• Make sure the audio cables are
connected.
• Make sure mute isn’t active in
the Audio menu.
• Make sure the volume is turned
up enough.
• Adjust the audio source.
• If playing a video, make sure the
playback has not been paused.
Customizing the projector
You can customize the projector for your specific setup and needs. See page 21 to page 23 for
details on these features.
• For rear projection, turn Rear mode on in the Settings>System menu.
• For ceiling mounted projection, turn Ceiling mode on in the Settings> System menu.
• Turn on Automatic Vertical Keystone adjustments.
• Specify which source the projector checks first for active video during power-up.
• Turn the projector’s display messages on and off.
• Turn on power saving features.
• Specify blank screen colors and startup logos.
• Specify the menu language.
• Control your projector using RS232 commands. See page 5.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Optimizing video images
After the video device is connected properly and the image is on the screen, you can optimize the
image using the onscreen menus. For general information on using the menus, see page 17.
• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu. See page 18.
• Change the Aspect ratio. Aspect ratio is the ratio of the image width to image height. TV
screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9.
Choose the option that best fits your input source. See page 18.
• Select a Sharpness setting. See page 20.
• Select a different Color Temperature or use the Color Control to adjust the gain and offset of the
red, green, and blue color. See page 20.
• Select a specific Gamma or Color Space. See pages 19 and 20.
• Turn Overscan on to remove noise
around the video image. See page 19.
Using the menus
To open the menus, press the Menu
button on the keypad or remote. (The
menus automatically close after 60
seconds, if no buttons are pressed.) The
Main menu appears. Use the arrow
buttons to move up and down to highlight
the desired submenu, then press the
Select button.
To change a menu setting, highlight it,
press Select, then use the up and
down arrow buttons to adjust the value,
select an option using radio buttons,
or turn the feature on or off using check
boxes. Press Select to confirm your
changes. Use the arrows to navigate to
another setting. When your adjustments
are complete, navigate to Exit, then
press Select to go to the previous menu;
press the Menu button at any time to
close the menus.
Dots appear before the menu name. The
number of dots indicate the menu’s level,
ranging from one (the Main menu) to four
(the most nested menus).
The menus are grouped by usage:
• The Picture menu provides image adjustments.
• The Settings menu provides set-up type adjustments that are not changed often.
• The About menu provides a read-only display of information about the projector and source.
Certain menu items may be grayed out until a particular source is connected. For example,
Sharpness is only available for video sources and will be hidden when a computer source is
active. Other menu items may be grayed out when they are not available. For example,
Brightness is grayed out until an image is active.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Picture menu
To adjust the following six
settings, highlight the setting,
press Select, use the up and
down arrows to adjust the
values, then press select to
confirm the changes.
Vertical Keystone: adjusts the
image vertically and makes a
squarer image. You can also
adjust vertical keystone from the
keypad. If you want the projector
to automatically adjust the
vertical keystone, check the Auto
Vertical check box.
Horizontal Keystone: adjusts
the image horizontally and
makes a squarer image.
Contrast: controls the degree of
difference between the lightest
and darkest parts of the picture
and changes the amount of black
and white in the image.
Brightness: changes the
intensity of the image.
Color: (video and component
sources only) adjusts a video
image from black and white to
fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the image.
Aspect Ratio: aspect ratio is the ratio of the image width to image height. TV screens are usually
1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9. The default is16:9.
Native: this mode bypasses the internal scaler, displaying the image with no resizing. Since the
native resolution is 1280x720 and 4x3 video images are approximately 640x480, 4x3 images will
always be smaller than the display and will be centered in the display. Computer images
1024x768 or smaller will also be centered in the display. If a 16x9 video source or a 1280x1024
or larger computer source is viewed, it will display up to 1280 pixels and 720 lines from the center
of the input.
16:9: the default is 16:9,
which preserves the 16:9
aspect ratio and is designed
to be used with content that
is enhanced for widescreen
TVs.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
4:3: resizes the image
from its original version
to fit a standard 4:3
aspect ratio screen. If
you have a 4:3 source
on a 16:9 screen, the
image is placed in a
16:9 space, so black
bars appear at the
sides of the image.
Letterbox text: preserves
the 16:9 aspect ratio and
maximizes readability of
the text.
Letterbox: preserves the
16:9 aspect ratio. If you
have a 16:9 source and
screen, the image fills the
screen. If your source is
letterboxed, the image is expanded to fill the screen.
Natural Wide: this
mode stretches a 4:3
image to fill the entire
16:9 screen. The center
two-thirds of the image
is unchanged; the
edges of the image are
stretched.
Presets: You can customize the settings for each source and save
them as a preset. There are three user-definable presets. To set a
preset for the current source, adjust the image; then choose Save
User 1, 2, or 3. You can recall these settings in the future by
selecting the appropriate user presets.
Gamma: Gamma tables contain preset intensity configurations
optimized for the input source. You can select a gamma table that has
been specifically tuned for film, presentation, or photography.
NOTE: Your viewing preferences may vary. Cycle through the gamma
options and pick the one you like the best.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Overscan: (video sources only) removes noise around the
video image.
Advanced settings
Sharpness: (video sources only) changes the clarity of
the edges of a video image. Select a sharpness setting.
Color Space: This option applies to computer sources. It allows you to
select a color space that has
been specifically tuned for the
video input. When Auto is
selected, the projector
automatically determines the
standard. To choose a different
setting, turn off Auto, then
choose RGB for computer
sources, choose either
SMPTE240, REC709 or
REC601 for component
sources.
Color Temperature: changes the relative warmth of the colors.
Color Control: allows you to individually adjust the gain
(intensity of the color), the offset (the amount of black in the
color), and the gamma of the red, green, and blue colors.
The following four options are for computer and component
sources only.
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer
source.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Settings menu
Audio: allows adjustments to the volume and mute, and turns the
projector’s startup Chime on and off.
Sources: allows you to assign a particular input to a specific source
key on the remote. Also allows selection of a default Startup Source
and enables or disables Autosource and RGB Video.
Sources>Startup Source: this determines
which source the projector checks for first
for active video during power-up.
Sources>Autosource: When Autosource
is not checked, the projector defaults to the
source selected in Startup Source. If no
source is found, a blank screen displays.
When Autosource is checked, Startup
Source determines which source the
projector defaults to at power-up. If no
signal is present, the projector checks the
sources in order until a source is found or
until power-down.
Sources>RGB Video: check this box if you are using a DVD player with RGB output.
System>Rear: reverses the image so you can project from behind a translucent screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
Auto Ceiling: automatically senses when the projector is inverted and turns the image upside
down. This is “On” by default.
Auto Power: When Auto Power is
checked, the projector
automatically goes into the startup
state after the projector is powered
on. This allows control of ceiling
mounted projectors with a wall
power switch.
Display Messages: displays
status messages (such as
“Searching” or “Mute”) in the
lower-left corner of the screen.
Power Save: automatically turns
the lamp off after no signals are detected for five minutes. After three additional minutes with no
signal, the projector powers down. If an active signal is received before the projector powers
down, the image will be displayed.
Screen Trigger: turns on the 12-volt DC output switch on the connector panel.
Backlight: allows you to turn off the backlighting on the keypad.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Sleep Timer: allows you to force the projector to automatically shutoff after
4 hours.
Screen Save: automatically blanks the screen with a black color
after no signals are detected for a preset number of minutes. The
image returns when an active source is detected or a remote or
keypad button is pressed. Screen Save is disabled when Power
Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue
screen instead of the default screen at startup and when no source
is detected. It also allows you to capture and display a custom
startup screen.
To capture a custom logo, display the image you want to capture on your computer, highlight
Capture New, then press Select twice. When complete, the projector confirms the capture.
The next time you start the projector, the custom logo you captured displays.
Blank Screen: determines what color is displayed when you
press the Blank button on the remote.
PiP: (Picture in Picture) allows you to overlay a smaller
window showing the video source on top of the larger computer
source window. You must have both a computer and video source
connected to use PIP. You can’t show a computer image in the
smaller PiP window, only a video image. You can select a small,
medium, or large window. You can also move the PiP window on
the screen using the PiP Position X and Y options in the menu.
Press the up and down arrows to change the position.
Language: allows you to select a language for the onscreen
display of menus and messages.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their
default after displaying a confirmation dialog box.
Lamp Reset: resets the lamp hours counter in the About menu to
zero. Do this only after changing the lamp. It displays a confirmation
dialog box.
Service Info: provides information about the projector’s software version and the active source.
Service Code: only used by authorized service personnel.
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens
cleaner to a soft, dry cloth.
Avoid using an excessive amount of
cleaner, and don’t apply the
cleaner directly to the lens. Abrasive
cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the
lens in a circular motion. If you
don’t intend to use the projector
immediately, replace the lens cap.
Replacing the projection lamp
The lamp hour timer in the
About menu counts the number
of hours the lamp has been in
use. When the lamp timer
reaches the estimated total lamp
life, the LED on the projector’s
keypad blinks red (indicating a
lamp error, see page 26) and a
dialog box appears each time the
projector is turned on.
You can order new lamp
modules from your dealer.
1 Turn off the projector and
unplug the power cable.
2 Wait 60 minutes to allow the projector
to cool thoroughly.
3 Turn the projector upside down and
remove the lamp door by loosening
the captive screw and then prying the
lamp door out.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
4 Remove the two screws on the lamp
module.
WARNINGS:
• To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass portion of the lamp module. Fingerprints can obscure projection
sharpness.
• Be extremely careful when removing the lamp housing. In the unlikely event that the lamp
ruptures, small glass fragments may be generated. The lamp module is designed to contain most
of these fragments, but use caution when removing it. Before replacing the lamp, clean the lamp
compartment and dispose of cleaning materials. Wash hands after lamp replacement. This
product has a lamp, which contains a very small amount of mercury. Dispose of it as required by
5 Carefully remove the lamp
module by grasping and lifting
the metal bail wire. Dispose of
the lamp in an environmentally
proper manner.
6 Install the new lamp module,
making sure that it is properly
seated (model SP17).
7 Replace the two screws.
8 Replace the lamp door and tighten the screw.
9 Plug in the power cable then press the Power
button to turn the projector back on.
10 Reset the lamp hour timer by navigating to
the Settings>Service menu and selecting
Lamp Reset.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Cleaning the dust filters
In dirty or dusty environments, the
dust filters can become clogged,
causing high temperatures inside the
lamp module. These high
temperatures can impact lamp
performance and operating life.
Routine maintenance to remove dust
and dirt from the filters lowers the
lamp operating temperature and
prolongs lamp life. To maximize lamp
life you will need to clean the filters
every 250 hours. Lamp filter
maintenance may need to occur more
often than 250 hours depending on
your installation/use environment.
There are two filters, one mesh filter attached to the dust filter door and one
metal grid filter adjacent to the lamp door.
1 Turn off the projector and unplug the power cable.
2 Wait 60 minutes to allow the projector to cool thoroughly.
WARNING: To avoid burns, allow the projector to cool for at least 60
minutes before you clean or replace the dust filter.
3 Turn the projector upside down and remove the lamp door. See page 23.
4 Remove the dust filter door.
5 Clean the filter using a vacuum set on low
power.
6 Replace the dust filter door and the lamp door.
7 Vacuum the non-removable metal grid filter
adjacent to the lamp door.
Using the security lock
The projector has a security lock for use with
a cable lock system. Refer to the information
that came with the lock for instructions on
how to use it.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Red LED behavior and projector errors
If the projector is not functioning properly and the red LED is blinking, consult Table 2 to
determine a possible cause. There are two-second pauses between the blinking cycles.
Table 3:
Red LED Behavior
Explanation
One (1) blink
The lamp won’t strike after five attempts. Check the
lamp and lamp door installations for loose connectors.
Two (2) blinks
The lamp counter hours have exceeded lamp life hours.
Replace the lamp and reset the lamp hours counter.
Three (3) blinks
The projector has shut down the lamp. Turn the
projector off and wait one minute, then turn the
on. If the lamp does not turn on, replace the lamp.
Contact Technical Support for repair if replacing the
lamp does not solve the problem.
Four (4) blinks
Five (5) blinks
A fan has failed. Contact Technical Support for repair.
The projector is overheating. Check for a blocked air
vent. Contact Technical Support for repair if clearing
The air vent does not solve the problem.
Projected image size
Table 4:
Image sizes
Distance to
Minimum
Maximum
Minimum
Maximum
screen (feet/m)
Diagonal (feet/m)
throw ratio 1.72
Diagonal (feet/m)
throw ratio 1.44
Horizontal
(feet/m)
Horizontal
(feet/m)
throw ratio 1.98
throw ratio 1.98
5/1.5
10/3
2.9/0.9
5.8/1.8
3.5/1.1
6.9/2.1
2.6/0.8
5.1/1.5
3.1/0.9
6.0/1.8
15/4.6
20/6.1
30/9.1
32.8/10
8.7/2.6
10.4/3.2
13.8/4.2
20.6/6.3
22.6/6.9
7.6/2.3
9.0/2.8
11.6/3.5
17.3/5.3
18.9/5.8
10.1/3.1
15.1/4.6
16.5/5.0
12.0/3.7
18.0/5.5
19.7/6.0
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Limited Warranty
Knoll Systems, Inc. (“Knoll”) warrants that each HD225 (“the Product”) sold hereunder will conform to and
function in accordance with the written specifications of Knoll. Said limited warranty shall apply only to the
first person or entity that purchases the Product for personal or business use and not for the purpose of
distribution or resale. Said warranty shall continue for a period of two (2) years from the date of such
purchase. The standard limited warranty excludes the lamps in projectors after 90 days or 500 hours and the
accessories after one year. Knoll does not warrant that the Product will meet the specific requirements of the
first person or entity that purchases the Product for personal or business use. Knoll’ liability for the breach of
the foregoing limited warranty is limited to the repair or replacement of the Product or refund of the purchase
price of the Product, at Knoll’ sole option. Replacement Product may be re-furbished in “like-new” condition,
at Knoll’ sole discretion. To exercise the Purchaser’s rights under the foregoing warranty, the Product must
be returned at the Purchaser’s sole cost and expense, to Knoll or to any authorized Knoll service center
provided, and the Product must be accompanied by a written letter explaining the problem and which
includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the
Product. When sending your unit in for repair, please ship your unit in its original packing material or a Knoll
approved ATA Shipping Case, or have a professional packaging company pack the unit. Please insure your
shipment for its full value. A return authorization number, issued by the Knoll customer service department,
must also be clearly displayed on the outside of the shipping carton containing the Product.
Note: Remanufactured Products are exempt from the foregoing Limited Warranty. Please refer to the
Remanufactured Product Warranty for applicable warranty information.
WARRANTY LIMITATION AND EXCLUSION
Knoll shall have no further obligation under the foregoing limited warranty if the Product has been damaged
due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications,
tampering, alterations, or service other than by Knoll or its authorized agents, causes other than from
ordinary use or failure to properly use the Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE
FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN
INSTRUMENT SIGNED BY KNOLL. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT KNOLL’ LIABILITY WHETHER IN CONTRACT, IN TORT,
UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF
THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES
SHALL KNOLL BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT
IS A CONSIDERATION IN LIMITING KNOLL’ LIABILITY. NO ACTION, REGARDLESS OF FORM,
ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT BY PUR-
CHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHT WHICH VARIES
FROM STATE TO STATE.
Copyright 2004 Knoll Systems. All Rights Reserved.
Knoll Systems
11791 Machrina Way #210
Richmond, BC V7A 4V3
Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|