INSTRUCTION MANUAL
MID POWER VHF APCO P25 TRANSCEIVER
TK-5710
HIGH POWER VHF APCO P25 TRANSCEIVER
TK-5710H
© B62-1816-10 (K)
09 08 07 06 05 04 03 02 01
Download from Www.Somanuals.com. All Manuals Search And Download.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer for technical assistance.
PRECAUTIONS
Observe the following precautions to prevent fire, personal injury, and transceiver
damage.
•
•
•
Do not attempt to configure the transceiver while driving; it is too dangerous.
Do not disassemble or modify the transceiver for any reason.
Do not expose the transceiver to long periods of direct sunlight, nor place it near
heating appliances.
•
•
•
If an abnormal odor or smoke is detected coming from the transceiver, switch the
transceiver power off immediately, and contact your KENWOOD dealer.
Use of the transceiver while you are driving may be against traffic laws. Please check
and observe the vehicle regulations in your area.
Do not use options not specified by KENWOOD.
◆
The transceiver operates in 12 V negative ground systems only! Check the battery polarity and
voltage of the vehicle before installing the transceiver.
◆
◆
Use only a KENWOOD optional DC power cable.
Do not cut and/or remove the fuse holder on the DC power cable.
For passenger safety, install the transceiver securely using an optional mounting bracket and screw
set so the transceiver will not break loose in the event of a collision.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
UNPACKING AND CHECKING EQUIPMENT ................................... 1
SUPPLIED ACCESSORIES ..................................................................... 1
PREPARATION .................................................................................. 2
TOOLS REQUIRED .............................................................................. 2
POWER CABLE CONNECTION ............................................................... 2
INSTALLING THE TRANSCEIVER .............................................................. 3
GETTING ACQUAINTED ................................................................... 4
KCH-14 (BASIC CONTROL PANEL) ..................................................... 4
KCH-14 DISPLAY ............................................................................. 5
KCH-15 (FULL-FEATURED CONTROL PANEL) ....................................... 6
KCH-15 DISPLAY ............................................................................. 7
TK-5710 REAR PANEL...................................................................... 8
TK-5710H REAR PANEL ................................................................... 8
PROGRAMMABLE FUNCTIONS ...................................................... 9
BASIC OPERATIONS .......................................................................11
SWITCHING POWER ON/ OFF........................................................... 11
ADJUSTING THE VOLUME ................................................................... 11
SELECTING A ZONE AND CHANNEL ...................................................... 12
TRANSMITTING ................................................................................. 12
RECEIVING ...................................................................................... 13
SCAN ................................................................................................ 14
TEMPORARY CHANNEL LOCKOUT ........................................................ 14
PRIORITY SCAN ............................................................................... 15
SCAN REVERT ................................................................................. 15
SCAN PROGRAMMING ....................................................................... 16
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION........... 17
KEY FUNCTIONS............................................................................... 17
SELCALL (SELECTIVE CALLING) ......................................................... 18
STATUS MESSAGE ............................................................................ 18
SHORT MESSAGES ........................................................................... 20
LONG MESSAGES ............................................................................. 20
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
DTMF (DUAL TONE MULTIE FREQUENCY) CALLS .................... 21
MAKING A DTMF CALL.................................................................... 21
AUTODIAL ....................................................................................... 21
STUN CODE .................................................................................... 21
EMERGENCY CALLS...................................................................... 22
SCRAMBLER (FM)/ ENCRYPTION (APCO)................................... 23
SECURE (ENCRYPTED) TRANSMISSION ................................................. 23
SELECTING THE SCRAMBLER CODE (FM) ............................................ 23
SELECTING THE ENCRYPTION KEY (APCO) ........................................ 23
DELETING THE ENCRYPTION KEY ........................................................ 24
PASSWORD PROTECTION ................................................................... 24
SIGNALING ...................................................................................... 25
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) ................................. 25
OPTION SIGNALING........................................................................... 26
CLOCK ............................................................................................. 27
CLOCK ADJUSTMENT ........................................................................ 27
ADVANCED OPERATIONS ............................................................. 28
BACKGROUND OPERATIONS ....................................................... 33
TIME-OUT TIMER (TOT) ................................................................... 33
COMPANDER .................................................................................... 33
PTT ID.......................................................................................... 33
BUSY CHANNEL LOCKOUT (BCL) ...................................................... 34
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT ................... 35
VOICE RECORDER ............................................................................ 35
VOICE GUIDE .................................................................................. 36
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorized
KENWOOD service facility, or the factory.
Carefully unpack the transceiver. We recommend that you identify the items
listed in the following table before discarding the packing material. If any items
are missing or have been damaged during shipment, file a claim with the carrier
immediately.
SUPPLIED ACCESSORIES
Item
Part Number
E37-0733-XX
N99-0365-XX
B62-1816-XX
Quantity
Short plug
1
1
1
Hex-headed screw with washer
Instruction manual
Short plug
Hex-headed screw
with washer
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Various electronic equipment in your vehicle may malfunction if they are not properly protected from
the radio frequency energy which is present while transmitting. Electronic fuel injection, anti-skid
braking, and cruise control systems are typical examples of equipment that may malfunction. If your
vehicle contains such equipment, consult the dealer for the make of vehicle and enlist his/her aid in
determining if they will perform normally while transmitting.
Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized
KENWOOD service facility, or the factory.
TOOLS REQUIRED
Note: Before installing the transceiver, always check how far the mounting screws will extend below
the mounting surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts.
The following tools are required for installing the transceiver:
•
•
1/4 inch (6 mm) or larger electric drill
5/32 inch (4.2 mm) drill bit for the self-tapping screws used to mount the optional
mounting bracket
•
Circle cutters
POWER CABLE CONNECTION
◆
The transceiver operates in 12 V negative ground systems only! Check the battery polarity and
voltage of the vehicle before installing the transceiver.
◆
◆
Use only a KENWOOD optional DC power cable.
Do not cut and/or remove the fuse holder on the DC power cable.
1 Check for an existing hole, conveniently located in the firewall, where a power
cable can be passed through. If no hole exists, use a circle cutter to drill the
firewall, then install a rubber grommet.
2 Run the two power cable leads through the firewall and into the engine
compartment, from the passenger compartment.
3 Connect the red lead to the positive (+) battery terminal and the black lead to
the negative (–) battery terminal.
•
Locate the fuse as close to the battery as possible.
4 Coil and secure the surplus cable with a retaining band.
•
Be sure to leave enough slack in the cables so the transceiver can be removed for
servicing while keeping the power applied.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE TRANSCEIVER
For passenger safety, install the transceiver securely using an optional mounting bracket and screw
set so the transceiver will not break loose in the event of a collision.
1 Mark the position of the holes in the dash by using the mounting bracket as a
template. Drill the holes, then attach the mounting bracket using self-tapping
screws.
•
Be sure to mount the transceiver in a location where the controls are within easy
reach of the user and where there is sufficient space at the rear of the transceiver
for cable connections.
2 Connect the antenna and power cable to the transceiver.
3 Slide the transceiver into the mounting bracket and secure it using
hex-headed screws.
4 Mount a microphone hanger in a location where it will be within easy reach of
the user yet not interfere with the safe operation of the vehicle.
When replacing the fuse in the DC power cable, be sure to replace it with a fuse of the same value.
Never replace a fuse with a fuse that has a higher value.
Microphone
hanger
Hex-headed
screws
Microphone
Power input
connector
Short
plug
Mounting
bracket
Antenna
connector
Fuse
DC power
cable
Hex-headed
screw
12 V vehicle
battery
Black (–) cable
Fuse holder
Ground lead
(commercially available)
Red (+) cable
* The TK-5710 is shown in the above diagram.
Note: The items above shown in gray are optional accessories.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
GETTING ACQUAINTED
KCH-14 (BASIC CONTROL PANEL)
q
w e
r
t
POWER
GRP
TX BUSY
VOL
CH
y
u
i
o
!
q Power switch
Press to switch the transceiver ON. Press and hold for approximately
1 second to switch the transceiver OFF.
w GRP key
Press to increase the zone number. Also press to increase setting adjustments.
e GRP key
Press to decrease the zone number. Also press to decrease setting adjustments.
r Display
Refer to page 5.
t Speaker
Internal speaker.
y TX and BUSY indicators
The TX indicator lights red while transmitting. The BUSY indicator lights
green while receiving.
u Microphone jack
Insert the microphone plug into this jack.
i VOL (Volume) control
Rotate clockwise to increase the volume level. Rotate counterclockwise to
decrease the volume level.
o CH (Channel) control
Rotate clockwise to increase the channel number. Rotate counterclockwise
to decrease the channel number. Your dealer can also enable the CH control
to be used when making setting adjustments, as an optional method for using
the GRP
and GRP
keys.
! PF 1 ~ PF 5 (Programmable Function) keys
Press to activate their programmable functions {page 9}.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
KCH-14 DISPLAY
Indicator
Description
Displays the operating zone and channel numbers or zone and
channel names. Also displays various text messages
depending on the function being used.
Displays the operating zone and channel numbers. Also
displays OST list numbers and various characters depending
on the function being used.
Appears when a received call is using optional signaling.
Appears when Monitor function is active and when the
transceiver squelch is open.
Appears when you are using Scan mode.
Appears when the external speaker function is activated.
Appears when the Scrambler or Encryption function is
activated.
Appears when the AUX A function has been activated.
Appears when the AUX B function has been activated.
Appears when using the Operator Selectable Tone function.
Appears when there is a message stored in the transceiver
memory. Flashes when a new message has arrived.
Appears when the selected channel is added to the scanning
sequence.
Appears when the AUX C function has been activated.
Appears when the Auto Recording function on the VGS-1
option is activated.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
KCH-15 (FULL-FEATURED CONTROL PANEL)
q
w e
r
t y
u
POWER
MON
SCN
GRP
TX BUSY
VOL
CH
i
o
!
!
!
q Power switch
Press to switch the transceiver ON. Press and hold for approximately
1 second to switch the transceiver OFF.
w GRP key
Press to increase the zone number. Also press to increase setting adjustments.
e GRP key
Press to decrease the zone number. Also press to decrease setting adjustments.
r Display
Refer to page 7.
t MON (Monitor) key
Press to activate the Monitor function. Press and hold to turn the squelch off
{page 30}.
y SCN (Scan) key
Press to activate the Scan function {page 14}.
u Programmable Function keys
Press to activate their programmable functions {page 9}.
i TX and BUSY indicators
The TX indicator lights red while transmitting. The BUSY indicator lights
green while receiving.
o Microphone jack
Insert the microphone plug into this jack.
! VOL (Volume) control
Rotate clockwise to increase the volume level. Rotate counterclockwise to
decrease the volume level.
! CH (Channel) control
Rotate clockwise to increase the channel number. Rotate counterclockwise
to decrease the channel number. Your dealer can also enable the CH control
to be used when making setting adjustments, as an optional method for using
the GRP
and GRP
keys.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
! PF 1 ~ PF 5 (Programmable Function) keys
Press to activate their programmable functions {page 9}.
KCH-15 DISPLAY
Indicator
Description
Displays the operating zone and channel numbers or zone and
channel names. Also displays various text messages
depending on the function being used.
Displays the operating zone and channel numbers. Also
displays OST list numbers and various characters depending
on the function being used.
Appears when a received call is using optional signaling.
Appears when Monitor function is active and when the
transceiver squelch is open.
Appears when you are using Scan mode.
Appears when the external speaker function is activated.
Appears when the Scrambler or Encryption function is
activated.
Appears when the AUX A function has been activated.
Appears when the AUX B function has been activated.
Appears when the AUX C function has been activated.
Appears when using the Operator Selectable Tone function.
Appears when the selected channel is added to the scanning
sequence.
Appears when there is a message stored in the transceiver
memory. Flashes when a new message has arrived.
Appears when the Auto Recording function on the VGS-1
option is activated.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TK-5710 REAR PANEL
External accessory
connector (D-sub 25 pin)
Antenna connector
External accessory
connector (9-pin)
Power input
connector
TK-5710H REAR PANEL
External accessory
connector (D-sub 25 pin)
Antenna connector
External accessory
connector (9-pin)
Power input
connector
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMABLE FUNCTIONS
The PF (Programmable Function) keys can be programmed with the functions
listed below. Please contact your dealer for further details on these functions.
Conventional FM: Channels set up for Conventional FM
Operation
Conventional APCO: Channels set up for Conventional
APCO Operation
✓ : Available
• : Mixed Mode only
N/A: Not Available
Conventional Conventional Reference
Programmable Function
FM
✓
APCO
N/A
N/A
✓
Page
28
2-tone
Autodial
21, 28
28
✓
AUX A
✓
AUX B
28
✓
✓
AUX C
28
✓
✓
Call Response
Channel Down
Channel Recall
Channel Select 1
Channel Up
Clock
N/A
✓
28
✓
12, 28
28
✓
✓
✓
12, 28
12, 28
27, 29
29
✓
✓
✓
✓
✓
✓
Direct Channel 1 ~ 5
Display Character
Emergency 2
External Speaker
Function
✓
✓
29
✓
✓
22, 29
29
✓
✓
✓
✓
29
✓
✓
Home Channel
Horn Alert
29
✓
✓
29
✓
✓
Individual
N/A
✓
13, 29
30
✓
Intercom
✓
Key Delete
LCD Brightness
N/A
✓
24, 30
30
✓
✓
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventional Conventional Reference
Programmable Function
FM
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
•
APCO
✓
✓
•
Page
30
Monitor
None
30
Operator Selectable Tone
OST Down
25, 30
30
•
OST Up
•
30
Playback
31, 36
31
✓
✓
✓
✓
✓
✓
✓
•
Public Address
Scan
14, 31
14, 31
16, 31
23, 31
23, 31
18, 31
18, 31
32
Scan Delete
Scan Program
Scrambler/ Encryption
Scrambler/ Encryption Code
Selcall
Selcall + Status
Speaker 1 – 2 Mute
Squelch Level
Status
•
✓
•
32
•
18, 32
32
Tactical Group
Talk Around
Talkgroup
✓
✓
✓
✓
✓
✓
✓
32
12, 32
32
Tone
✓
✓
✓
✓
Zone Down
Zone Select 1
12, 32
12, 32
12, 32
Zone Up
1 Channel Select and Zone Select can be programmed only on the CH control.
2 Emergency can be programmed only on the PF 5 key (the fifth key from the left, after the CH control).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
SWITCHING POWER ON/ OFF
Press the switch to switch the transceiver ON.
•
•
A beep sounds and the display momentarily lights up.
If the Transceiver Password function is programmed, “PASSWORD” appears on the
display. You must enter the password to unlock the transceiver. Refer to “Transceiver
Password”, below.
Press and hold the switch for approximately 1 second to switch the transceiver
OFF.
■ TRANSCEIVER PASSWORD
To enter the password:
1 Rotate the CH control to select a digit.
2 Press the GRP
digit.
key to accept the entered digit and move to the next
3 Repeat steps 1 and 2 to enter the entire password.
•
•
The password can contain a maximum of 6 digits.
Press the PF 3 key (the third key from the left, after the CH control) to delete an
incorrectly entered character. Press and hold the PF 3 key to delete all
characters.
4 Press the PF 2 key (the second key from the left, after the CH control) to
confirm the password.
•
If you enter an incorrect password, an error tone sounds and the transceiver
remains locked.
To enter the password using a DTMF keypad:
1 Press the DTMF keys corresponding to the password digits.
•
•
The password can contain a maximum of 6 digits.
Press the PF 3 (the third key from the left, after the CH control) or DTMF # key
to delete an incorrectly entered character. Press and hold the PF 3 or DTMF #
key to delete all characters.
2 Press the PF 2 or DTMF key to confirm the password.
•
If you enter an incorrect password, an error tone sounds and the transceiver
remains locked.
ADJUSTING THE VOLUME
Rotate the VOL control clockwise to increase the volume and counterclockwise
to decrease the volume.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING A ZONE AND CHANNEL
Select the desired zone using the GRP
group of channels.
and
keys. Each zone contains a
Select the desired channel using the CH control. Each channel is programmed
with settings for transmitting and receiving.
•
If programmed by your dealer, the transceiver will announce the zone and channel
numbers as you change them.
Names can be programmed for zones and personalities. Your dealer can set the
zone name to a length of 0 to 14 digits. To fit on the display, personality names
will shorten appropriately. (KCH-14 models display only 12 digits). For example,
if the channel name is “–CHANNEL1–” and the zone name is “KENWOOD”, and
your dealer sets the zone name to 4-digits, the following display will appear:
KCH-14 (12-digit display):
KCH-15 (14-digit display):
KENW–CHANNEL
KENW–CHANNEL1–
TRANSMITTING
1 Select the desired zone and channel using the GRP
CH control.
and
keys and the
2 Press (or press and hold) the key programmed as Monitor to check whether
or not the channel is free.
•
If the channel is busy, wait until it becomes free.
3 Press the microphone PTT switch and speak into the microphone. Release
the PTT switch to receive.
•
•
The TX indicator lights red while transmitting. The BUSY indicator lights green
while receiving a signal. This indicator can be disabled by your dealer.
For best sound quality at the receiving station, hold the microphone approximately
1.5 inches (3 ~ 4 cm) from your mouth.
■ MAKING GROUP CALLS (APCO)
Channels programmed for APCO operation already have a Group ID
assigned. For these channels, you do not need to perform steps 1 to 3,
below. Otherwise, if a key has been programmed with Talkgroup, you can
select a group ID from the list to make a call to those parties.
1 Press the key programmed as Talkgroup.
2 Press the GRP
and
ID/name from the list that has been pre-entered into your transceiver.
keys or rotate the CH control to select a group
•
The target group ID/name appears on the display.
3 Press the PF 1 key (the first key from the left, after the CH control) to
accept the group ID/name.
4 Press and hold the microphone PTT switch to make the call.
•
Speak into the transceiver as you would during a normal transmission.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
■ MAKING INDIVIDUAL CALLS (APCO)
If a key has been programmed with Individual, you can make calls to
specified persons.
1 Press the key programmed as Individual.
2 Press the GRP
from the list that has been pre-entered into your transceiver.
and
keys or rotate the CH control to select a unit ID
•
•
Alternatively, you can directly enter a unit ID by using a DTMF keypad.
The target unit ID/name appears on the display.
3 Press and hold the microphone PTT switch to make the call.
•
Speak into the transceiver as you would during a normal transmission.
RECEIVING
1 Select the desired zone and channel using the GRP
CH control.
and
keys and the
2 When you hear a caller’s voice, readjust the volume as necessary.
•
If signaling has been programmed on the selected channel, you will hear a call only
if the signal tone matches the tone set up on your transceiver.
Note: Signaling allows your transceiver to code your calls. This will prevent you from listening to
unwanted calls. It does not make calls private, it only prevents them from being heard by
transceivers set with a different signaling code. Refer to “SIGNALING” on page 25 for details.
■ RECEIVING GROUP CALLS (APCO)
When you receive a call on your group channel and the received group ID
matches the ID set up on your transceiver, you can hear the caller’s voice.
Readjust the volume as necessary.
■ RECEIVING INDIVIDUAL CALLS (APCO)
When you receive an individual call, a ringing tone will sound and the display
will show the caller’s ID. To respond to the call, press and hold the
microphone PTT switch and speak into the transceiver as you would during a
normal transmission.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SCAN
Scan is useful for monitoring signals on the transceiver channels. While
scanning, the transceiver checks for a signal on each channel and only stops on
a channel if a signal is present.
To begin scanning, press the key programmed as Scan.
•
•
The
(KCH-14) or
(KCH-15) icon appears on the display.
The channel add indicator (KCH-14:
appear on the display when the selected channel is added to the scan sequence.
/ KCH-15:
) will
•
•
The channels included in the scan list are scanned.
When a signal is detected on a channel, Scan pauses on that channel. The
transceiver will remain on the busy channel until the signal is no longer present. When
the signal “drops out”, the transceiver will remain on the channel momentarily before
Scan resumes. This delay time is programmed by your dealer. If a signal is received
during the delay time, the transceiver will remain on the same channel.
To stop scanning, press the Scan key again.
Note:
◆
If the currently selected channel is not added to the scanning sequence, Scan will not function
when pressing the key programmed as Scan. Be sure that the selected channel is added to the
scanning sequence before operating Scan.
◆
In order for Scan to function, there must be at least 2 channels added to the scanning sequence.
If there are less channels than this, Scan will not operate.
TEMPORARY CHANNEL LOCKOUT
If a key is programmed with the Scan Delete function, each channel can be
locked out of the scan sequence manually.
During scan, you can temporarily remove specific channels from the scanning
sequence by selecting them and pressing the Scan Delete key.
•
•
The channel add indicator (KCH-14:
longer appears on the display for that channel.
/ KCH-15:
) no
The channel is no longer scanned. However, when scanning is ended and restarted,
the channels will reset and the channel will again be in the scanning sequence.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PRIORITY SCAN
A Priority channel must be programmed in order for Priority Scan to function.
When using a single Priority channel, the transceiver will automatically change to
the Priority channel when a call is received on it, even if a call is being received
on a normal channel.
When using dual Priority channels, Priority channel 1 is given precedence over
Priority channel 2. So, if a call is received on Priority channel 1 while a call is
already on Priority channel 2, the transceiver will automatically change to Priority
channel 1.
•
“P1” appears on the sub-display when the displayed channel is Priority channel 1, “P2”
appears when the displayed channel is Priority channel 2, and “PP” appears when the
displayed channel is both Priority channel 1 and Priority channel 2.
SCAN REVERT
The Scan Revert channel is the channel selected when you press the PTT switch
to transmit during Scan. Your dealer can program 1 of 6 types of Scan Revert
channels on your transceiver:
•
Selected: The last zone and channel selected are assigned as the new revert zone
and channel.
•
Selected + Talkback: If the zone and channel have been changed during Scan, the
newly selected zone and channel are assigned as the new revert zone and channel.
The transceiver “talks back” on the current receive channel.
•
•
Priority 1: If your dealer has programmed a Priority 1 channel, this channel is the
revert zone and channel.
Priority 1 + Talkback: If your dealer has programmed a Priority 1 channel, this
channel is the revert zone and channel. The transceiver “talks back” on the current
receive channel.
•
•
Priority 2: If your dealer has programmed a Priority 2 channel, this channel is the
revert zone and channel.
Priority 2 + Talkback: If your dealer has programmed a Priority 2 channel, this
channel is the revert zone and channel. The transceiver “talks back” on the current
receive channel.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SCAN PROGRAMMING
Using the key programmed as Scan Program, you are able to reprogram your
scan list.
1 Press the key programmed as Scan Program.
•
The
(KCH-14 ) or
(KCH-15) icon appears on the display and blinks.
2 Press the GRP
and
and channel you will add to or remove from the Scan list.
keys or rotate the CH control to select the zone
•
Press the PF 4 key (the forth key from the left, after the CH control) to toggle
between Zone Select and Channel Select.
3 Press the PF 2 key (the second key from the left, after the CH control) to add
or remove the selected zone or channel to/ from the scan list.
•
The channel add indicator (KCH-14:
appear on the display when the selected channel is added to the scan sequence.
/ KCH-15:
) will
If the Priority channel has been set as Operator Selectable by your dealer, you
are able to reprogram the Priority mode as well.
1 Press the key programmed as Scan Program.
•
The
(KCH-14) or
(KCH-15) icon appears on the display and blinks.
2 Press the GRP
and channel you will add to or remove from the Scan list.
and
keys or rotate the CH control to select the zone
•
Press the PF 4 key (the forth key from the left, after the CH control) to toggle
between Zone Select and Channel Select.
3 Press the PF 3 key (the third key from the left, after the CH control).
4 Press the PF 4 key (the forth key from the left, after the CH control) to toggle
the selected channel between Priority mode and Normal mode.
•
“P1”, “P2”, or “PP” appears on the sub-display when Priority mode is
selected.
5 Press the PF 3 key again to set the new channel setting.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION
FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol owned
by KENWOOD Corporation. FleetSync enables a variety of paging functions on
your transceiver, some of which depend on dealer programming.
Note: This function is available only in Conventional FM Operation.
KEY FUNCTIONS
Key
Function
Selcall or
Press to change the transceiver mode as shown in the
Selcall + Status diagram below.
Rotate to select an ID from the pre-programmed ID list or
Status list.
CH control
PTT switch or
PF4 key
Press to initiate a call.
Keypad 0 ~ 9
Use the DTMF keypad to enter Selcall or Status numbers.
Press to exit Selcall or Status mode.
PF1 or
DTMF key
Normal Operating Mode
Press Selcall or Selcall + Status
Receive a
new message
Hold Selcall, Status
or receive a Selcall
or Selcall + Status
Press
any key
Press PF1
Selcall Mode 1
Stack Mode
New Message
Display Mode
Press PF2
Status Mode 2
Press
PF1 or
1 Depending on how your dealer programmed the transceiver, Selcall mode may be skipped or the
transceiver may exit Selcall mode automatically (as shown by the dash arrow).
2 After entering Selcall mode by pressing the Selcall + Status key, you can enter Status mode by
pressing the PF2 key.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SELCALL (SELECTIVE CALLING)
A Selcall is a voice call to a particular station or to a group of stations.
■ TRANSMITTING
1 Select your desired zone and channel.
2 Press the key programmed as Selcall or Selcall + Status to enter Selcall
mode.
3 Press the GRP and
the station you want to call.
keys or rotate the CH control to select the ID of
•
Alternatively, you can enter a station ID using a DTMF keypad.
4 Press the microphone PTT switch and begin your conversation.
•
Alternatively, you can press the PF 4 key to page the selected station, rather
than making a voice call.
■ RECEIVING
An alert tone will sound, the transceiver will automatically enter Selcall mode,
and the calling station’s ID will appear when a Selcall is received.
To respond to the call, press the microphone PTT switch and speak into the
microphone.
■ IDENTIFICATION CODES
An ID code is a combination of a 3-digit Fleet number and a 4-digit ID
number. Each transceiver must have its own Fleet and ID number.
•
•
•
•
•
Enter a Fleet number (100 ~ 349) to make a group call.
Enter an ID number (1000 ~ 4999) to make an individual call in your fleet.
Enter a Fleet number make a call to all units in the selected fleet (Fleet call).
Enter an ID number to make a call to the selected ID in all fleets (Supervisor call).
Select “ALL” Fleet and “ALL” ID to make a call to all units (Broadcast call).
Note: The ID range may be limited by programming.
STATUS MESSAGE
You can send and receive 2-digit Status messages which may be decided in your
talk group. Messages can contain up to 16 alphanumeric characters. Status
messages range from 10 to 99 (80 ~ 99 are reserved for special messages).
A maximum of 15 received messages can be stored in the Stack memory of your
transceiver. These saved messages can be reviewed after reception.
Depending on your dealer settings, when the Stack memory is full, either the
oldest message will be erased when a new message is received or the new
message will not be stored in the Stack memory.
•
The (KCH-14) or
stored in the Stack memory.
(KCH-15) icon appears when a message is
18
Download from Www.Somanuals.com. All Manuals Search And Download.
■ TRANSMITTING
1 Select your desired zone and channel.
2 Press the key programmed as Status to enter Status mode or
Selcall + Status to enter Selcall mode.
•
When using the Status key to enter Status mode, the target Fleet/ ID is fixed
and cannot be selected. Skip to step 5 to continue.
3 In Selcall mode, press the GRP
to select the ID of the station you want to call.
and
keys or rotate the CH control
•
Alternatively, you can enter a station ID using a DTMF keypad.
4 Press the PF 2 key (the second key from the left, after the CH control), to
enter Status mode.
5 Press the GRP
status ID you want to transmit.
and
keys or rotate the CH control to select the
•
Alternatively, you can enter a station ID using a DTMF keypad.
6 Press the microphone PTT switch or the PF 4 key to initiate the Status
call.
•
“<COMPLETE>” is displayed when the call has been successfully transmitted.
■ RECEIVING
The
ID or text message will appear when a Status call is received.
(KCH-14) or
(KCH-15) icon will flash and a calling
Press any key to return to normal operation.
■ REVIEWING MESSAGES IN THE STACK MEMORY
1 Press and hold the key programmed as Selcall, Status, or
Selcall + Status for 1 second to enter Stack mode.
•
The last received message is displayed with the message number.
2 Press the GRP
desired message.
and
keys or rotate the CH control to select the
3 Press the PF 1 key to return to normal operation.
•
To delete the selected message, press the PF 3 or DTMF # key. To confirm the
deletion, press the PF 2 or DTMF key.
•
To delete all messages, press and hold the PF 3 or DTMF # key for 1 second.
To confirm the deletion, press the PF 2 or DTMF key.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SHORT MESSAGES
To send a short message, you must connect the transceiver to a PC. Ask your
dealer for details.
•
•
Short messages can contain a maximum of 48 characters.
Received short messages are displayed the same as Status messages and are stored
in the same stack memory. A combined maximum of 15 Status calls and short
messages can be stored in the stack memory.
LONG MESSAGES
To send and receive long messages, you must connect the transceiver to a PC.
Ask your dealer for details.
•
Long messages can contain a maximum of 4096 characters.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DTMF (DUAL TONE MULTI FREQUENCY) CALLS
Note: DTMF calls can be made only in Conventional FM Operation.
MAKING A DTMF CALL
■ MANUAL DIALING
Note: To make a DTMF call using manual dialing, you must use an optional microphone with a
DTMF keypad.
1 Press and hold the microphone PTT switch.
2 Enter the desired digits using the DTMF keypad.
•
If you release the PTT switch, transmit mode will end even if the complete
number has not been sent.
■ STORE & SEND
1 Enter the desired digits using the DTMF keypad.
•
•
The digits appear on the display as you enter them.
You can enter up to 31 digits before transmitting.
2 After entering the complete number, press the microphone PTT switch to
transmit.
Note: If you switch the power OFF before transmitting the number, the number will be cleared.
■ KEYPAD AUTO PTT
If your dealer has activated the Keypad Auto PTT function, simply press the
keys on the keypad to make the call.
•
The DTMF code will be sent automatically when you press a key.
AUTODIAL
Autodial allows you to quickly call DTMF numbers that have been programmed
onto your transceiver.
1 Press the key programmed as Autodial.
•
“CODE?” or the first entry in the Autodial list appears on the display.
2 Press the GRP
appropriate DTMF number (01 ~ 32) to select your desired Autodial list number.
and
keys, rotate the CH control, or enter the
3 Press the microphone PTT switch or the PF 4 key to make the call.
STUN CODE
This function is used when a transceiver is stolen or lost. When the transceiver
receives a call containing a stun code, either transmit mode will be disabled, or
both receive mode and transmit mode will be disabled. The stun code is
cancelled when the transceiver receives a call with a revive code.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EMERGENCY CALLS
If your transceiver has been programmed with the Emergency function, you can
make emergency calls.
Note: Emergency can be programmed only on the PF 5 key (the fifth key from the left, after the CH
control).
1 Press and hold the key programmed as Emergency.
•
Depending on the delay time programmed into your transceiver, the length of time
you must hold the Emergency key will vary.
•
When the transceiver enters Emergency mode, the transceiver will change to the
Emergency channel and begin transmitting based on how the transceiver is set up
by your dealer. Transmit periods are also set by your dealer.
2 To exit Emergency mode, press and hold the Emergency key again.
•
If the Emergency mode completes the preset number of cycles, Emergency mode
will automatically end and the transceiver will return to the channel that was in use
before Emergency mode was entered.
Note:
◆
◆
Your dealer can set a beginning of transmit and end of transmit tone for the transceiver.
Your dealer can set the transceiver to emit tones and received signals as normal or mute the
speaker during Emergency operation.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SCRAMBLER (FM)/ ENCRYPTION (APCO)
Note:
◆
The Scrambler function can be used only in Conventional FM Operation. Additionally, the Voice
Scrambler board must be installed before this function can be activated.
◆
Ask your dealer for details concerning the Voice Scrambler board and the Encryption DES/AES
settings.
SECURE (ENCRYPTED) TRANSMISSION
Press the key programmed as Scrambler/ Encryption to switch the transceiver
to secure (encrypted) transmission.
•
•
The
(KCH-14) or
(KCH-15) icon appears on the display.
Pressing the microphone PTT switch after the Scrambler or Encryption function has
been turned ON encrypts the transmitted signal.
•
Each group member must activate their respective Scrambler/ Encryption functions to
descramble the received signals.
SELECTING THE SCRAMBLER CODE (FM)
1 Press the key programmed as Scrambler/ Encryption Code or press and
hold the key programmed as Scrambler/ Encryption for 1 second, to enter
Code Selection mode.
2 Press the GRP
and
decrease the Scrambler code.
keys or rotate the CH control to increase or
•
•
There are 16 available Scrambler codes (1 ~ 16).
Each group member must use the same code in order for the transceivers to
descramble the received signals.
3 Press the PF 1, PF 2, or PF 3 key (the first, second, or third key from the left,
after the CH control) to exit Code Selection mode.
SELECTING THE ENCRYPTION KEY (APCO)
1 Press the key programmed as Scrambler/ Encryption Code or press and
hold the key programmed as Scrambler/ Encryption for 1 second, to enter
Key Selection mode.
2 Press the GRP
Encryption key.
and
keys or rotate the CH control to select the new
•
•
There are 16 available Encryption keys (1 ~ 16).
Each group member must select a code that is in each member’s key list in order
for the transceivers to descramble the received signals.
3 Press the PF 1, PF 2, or PF 3 key (the first, second, or third key from the left,
after the CH control) to exit Key Selection mode.
Note: To return the transceiver to the default programmed Encryption key, select “PRESET”.
However, if you delete the Encryption key {page 24}, it will not be recovered.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DELETING THE ENCRYPTION KEY
1 Press the key programmed as Key Delete to enter Encryption Key Delete
mode.
2 Select the current Encryption key using the GRP
control .
and
keys or the CH
3 Press the PF 3 key (the third key from the left, after the CH control) to delete
the Encryption key.
4 Press the PF 1 or PF 2 key (the first or second key from the left, after the CH
control) to exit Encryption Key Delete mode.
Note: To delete all Encryption keys (when more than one key has been set up), select “ALL”.
PASSWORD PROTECTION
If the transceiver is password protected, entering an incorrect password
successively 15 times will automatically delete all the Encryption keys.
•
Turning the transceiver power OFF and the ON again will not reset the number of
attempts for entering an incorrect password.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SIGNALING
Note: Signaling can be used only in Conventional FM Operation.
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT)
Your dealer may have programmed QT or DQT signaling on your transceiver
channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to
ignore (not hear) calls from other parties who are using the same channel.
When a channel is set up with a QT tone or DQT code, squelch will only open
when a call containing a matching tone or code is received. Likewise, signals
that you transmit will only be heard by parties whose QT/ DQT signaling matches
your transceiver.
If a call containing a different tone or code is made on the same channel you are
using, squelch will not open and you will not hear the call. Although it may seem
like you have your own private channel while using QT/ DQT, other parties can
still hear your calls if they set up their transceiver with the same tone or code.
■ OPERATOR SELECTABLE TONE (OST)
If a key has been programmed with Operator Selectable Tone, you can
reprogram the QT tone or DQT code on each of your channels.
1 Select your desired zone and channel.
2 Press and hold the key programmed as Operator Selectable Tone for
1 second.
•
The (KCH-14) or (KCH-15) icon appears on the display when this
function is activated.
3 Press the GRP
and
keys, rotate the CH control, or enter the list
number directly using a DTMF keypad to select your desired tone or code
from 1 to 40.
4 Press the PF 1 or DTMF key to exit OST Selection mode.
•
OST is activated after seleting a list number and exiting OST Selection mode.
After selecting and setting up your desired tone or code, press the Operator
Selectable Tone key to toggle the OST function ON and OFF.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL SIGNALING
Your dealer may also program several types of option signaling for your
transceiver channels.
■ 2-TONE SIGNALING
2-tone Signaling opens the squelch only when your transceiver receives a call
containing matching 2 tones.
Refer to “2-tone” on page 28.
■ DTMF SIGNALING
DTMF Signaling opens the squelch only when the transceiver receives a call
containing a matching DTMF code.
Refer to “DTMF (DUAL TONE MULTI FREQUENCY) CALLS” on page 21.
■ FleetSync SIGNALING
Refer to “SELCALL (SELECTIVE CALLING)” on page 17.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOCK
If activated by your dealer, your transceiver can track the time with its built-in
clock. The time will display momentarily when the transceiver power is turned
ON. Additionally, you can view the clock any time by pressing the key
programmed as Clock.
CLOCK ADJUSTMENT
To set the time:
1 With the transceiver power OFF, press and hold the PF 4 key (the forth key
from the left, after the CH control) while turning the transceiver power ON.
•
The current time setting appears.
2 Press the GRP and
decrease the year setting.
keys or rotate the CH control to increase or
KCH-14 Display:
KCH-15 Display:
3 Press the PF 2 key (the second key from the left, after the CH control) to set
the year.
•
The transceiver cycles to the month setting.
4 Repeat steps 2 and 3 to set the month, day, hour, and minute.
5 Press the PF 2 key (the second key from the left, after the CH control) to
return to the year setting, after setting the minute.
6 Turn the transceiver power OFF and then back ON to return to normal
operation.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED OPERATIONS
Your transceiver operations vary according to the functions that your dealer has
programmed onto the transceiver keys. Following is brief overview of the
programmable functions. Refer to those functions which have been programmed
onto your transceiver.
•
2-tone
Press this key to display the list of 2-tone codes that has been pre-stored in
your transceiver memory. While viewing the 2-tone list, press the GRP
and keys or rotate the CH control to select your desired code, then press
the PTT switch to make the call.
•
Autodial
Press this key to quickly call a DTMF number that has been pre-stored in your
transceiver memory. While viewing the Autodial list, press the GRP
keys or rotate the CH control to select your desired code, then press the
and
PTT switch to make the call. Refer to “AUTODIAL” on page 21 for details.
•
•
•
AUX A
Press this key to activate the Auxiliary A port on the transceiver. When
activated, the (KCH-14) or (KCH-15) icon appears on the display.
AUX B
Press this key to activate the Auxiliary B port on the transceiver. When
activated, the (KCH-14) or (KCH-15) icon appears on the display.
AUX C
Press this key to activate the Auxiliary C port on the transceiver. When
(KCH-14) or (KCH-15) icon appears on the
activated, the
display.
•
•
Call Response
Press this key to respond to an Individual call.
Channel Down
Press this key to decrease the channel number. Press and hold this key to
cycle down through the channel numbers. If programmed by your dealer,
when the lowest channel number is reached, the transceiver will “roll-over” to
the highest channel number and continue cycling down.
•
•
Channel Recall
Press this key during Scan to return to the last called zone and channel.
Channel Select
Using the CH control, turn clockwise to increase the channel number and
counterclockwise to decrease the channel number.
•
Channel Up
Press this key to increase the channel number. Press and hold this key to
cycle up through the channel numbers. If programmed by your dealer, when
the highest channel number is reached, the transceiver will “roll-over” to the
lowest channel number and continue cycling up.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Clock
Press this key to display the current time.
Direct Channel 1 ~ 5
Press one of the five Direct Channel keys to jump to a frequently used zone
and channel. The zones and channels are programmed by your dealer.
If activated by your dealer, you can set your own Direct Channels. First,
select your desired zone and channel, then press and hold the Direct
Channel 1 ~ Direct Channel 5 key for 3 seconds to set your selected zone
and channel as that Direct Channel.
•
•
Display Character
Press this key to switch the display between the zone and channel number
and the zone and channel name (if names have been programmed).
Emergency
Press and hold this key to enter Emergency mode. This key is set up with a
delay time to avoid accidentally entering Emergency mode. The length of
time you must hold the key before entering Emergency mode depends on the
key setup. Refer to “EMERGENCY CALLS” on page 22 for details.
•
External Speaker
Press this key to switch the speaker from the transceiver’s built-in speaker to
an optional external speaker. When pressed, all messages and tones will
sound from the optional external speaker that is attached to the transceiver,
rather than from the transceiver’s built-in speaker. When using an external
speaker, the
(KCH-14) or
(KCH-15) icon appears on the display.
•
•
Function
Press this key to activate the second function of the programmable keys.
“FNC” appears on the sub-display when this key is pressed. Press a
programmable key to activate its secondary function.
Home Channel
Press this key to jump to your home zone and channel. Your home zone and
channel is programmed by your dealer.
If activated by your dealer, you can set your own Home Channel. First, select
your desired zone and channel, then press and hold the Home Channel key
for 3 seconds to set your selected zone and channel as the Home Channel.
•
•
Horn Alert
Press this key to toggle the Horn Alert function ON and OFF. “HORN ALERT”
appears on the display when Horn Alert is activated. When a call is received
that has a correct DTMF code or 2-tone signaling, Horn Alert causes the
vehicle horn or some other external alert to sound.
Individual
Press this key to activate the Individual Call function. When activated, you
must select the ID of the person you want to call before the call can be made.
Refer to “MAKING INDIVIDUAL CALLS” on page 13 for details.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Intercom
Press this key to toggle the Intercom function ON and OFF. “INTERCOM”
appears on the display when Intercom is activated. To use the Intercom
function, your dealer must first install a dual-head (microphone and speaker)
system. When making a call, your voice will be transmitted over the speaker
system.
•
•
Key Delete
Press this key to enter Encryption Key Delete mode. While in Encryption Key
Delete mode, you can select the key you want to delete. Refer to “DELETING
THE ENCRYPTION KEY” on page 24 for details.
LCD Brightness
Press this key to change the brightness level of the LCD. Each time this key
is pressed, the brightness levels cycle as follows:
High Medium Low Off
•
Monitor
Press this key to turn the transceiver signaling off. This will allow you to listen
to all calls that are received on your selected channel. While monitor is
activated, the
Press the Monitor key again to turn the transceiver signaling back on.
(KCH-14) or
(KCH-15) icon appears on the display.
Press and hold this key for 2 seconds to turn the transceiver squelch off. This
will allow you to better hear weak signals on your selected channel, as well as
background noise. While squelch is off, the
icon appears on the display. Press the Monitor key again to turn the
(KCH-14) or
(KCH-15)
transceiver squelch back on.
•
•
None
No function has been programmed on the key.
Operator Selectable Tone
Press and hold this key for 1 second to enter Tone Selection mode. When
activated, the
(KCH-14) or (KCH-15) icon appears on the display.
and keys, use the CH
control, or enter a number using a DTMF keypad to select your desired tone
When in Tone Selection mode, press the GRP
or code. Press the PF 1, PF 2, or DTMF key to complete the selection.
To toggle the OST function ON and OFF, press the Operator Selectable
Tone key. Refer to “QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT)” on page 25 for
details.
•
•
OST Down
Press this key to decrease the Operator Selectable Tone number of your
selected channel. (This key functions similar to the Operator Selectable Tone
key.)
OST Up
Press this key to increase the Operator Selectable Tone number of your
selected channel. (This key functions similar to the Operator Selectable Tone
key.)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Playback
Press this key to enter Playback mode. While in Playback mode, select the
desired memory channel to play back. Refer to “PLAYBACK” on page 36 for
details. Press and hold this key for 1 second to start recording a voice memo.
Refer to “VOICE MEMOS” on page 35 for details.
Public Address
Press this key to toggle the Public Address function ON and OFF. “PUBLIC
ADRS” appears on the display when Public Address is activated. To use the
Public Address system, your dealer must first install an external speaker.
This function causes all audio input via the microphone to be amplified and
output from the external speaker. Adjust the volume level as necessary when
using the Public Address system
•
•
•
•
Scan
Press this key to scan your transceiver channels for a signal. While scanning,
the
key again to quit scan. Refer to “SCAN” on page 14 for details.
(KCH-14) or
(KCH-15) icon appears on the display. Press this
Scan Delete
Press this key during scan operation to temporarily delete a channel from the
scanning sequence. The channel settings are returned to normal when scan
is ended. Refer to “TEMPORARY CHANNEL LOCKOUT” on page 14 for details.
Scan Program
Press this key to access the scan list. You can set each transceiver channel
to be added to or removed from your scan list. Refer to “SCAN PROGRAMMING”
on page 16 for details.
Scrambler/ Encryption
Press this key to activate or deactivate the Scrambler/ Encryption function.
When activated, the transceiver encrypts your voice so that anybody listening
to your conversation will not be able to understand what you are saying.
Press and hold this key for 1 second to enter Scrambler Code/ Encryption
Key Selection mode. Refer to “SCRAMBLER (FM)/ ENCRYPTION (APCO)”
on page 23 for details.
•
Scrambler/ Encryption Code
Press this key to enter Scrambler Code/ Encryption Key Selection mode.
After entering Scrambler Code/ Encryption Key Selection mode, press the
GRP
and
keys or rotate the CH control to change your Scrambler
code/ Encryption key from 1 to 16. Refer to “SCRAMBLER (FM)/
ENCRYPTION (APCO)” on page 23 for details.
•
•
Selcall
Press this key to enter Selcall mode. Press and hold this key to enter Stack
mode. Refer to “FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION”
on page 17 for details.
Selcall + Status
Press this key to enter Selcall mode. Press this key again to enter Status
mode. Press and hold this key to enter Stack mode. Refer to “FleetSync:
ALPHANUMERIC 2-WAY PAGING FUNCTION” on page 17 for details.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Speaker 1 – 2 Mute
Press this key to mute the secondary speaker when using a dual-head
system. The Head 1 speaker will mute when pressing this key from the Head
2 unit, and the Head 2 speaker will mute when pressing this key from the
Head 1 unit.
Squelch Level
Press this key to adjust the transceiver squelch level. When adjusting the
squelch level, use the the GRP
and decrease the squelch level.
and
keys or the CH control to increase
The squelch level can be adjusted from 0 (open) to 9 (tight). The default
setting is 5.
•
•
•
Status
Press this key to enter Status mode. Press and hold this key to enter Stack
mode. Refer to “FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION”
on page 17 for details.
Tactical Group
Press and hold this key for 1 second to register the selected channel as a
Tactical Group channel. Press and hold this key for 3 seconds to register all
channels within the current zone as Tactical Group channels.
Talk Around
Press this key to toggle Talk Around ON and OFF. When activated, “TA”
appears on the sub-display.
While using Talk Around, you free up the repeater and communicate directly
to other transceivers that are within range. If the other party is too far away,
you must continue to use the repeater to engage in communication.
•
•
Talkgroup
Press this key to select the Group ID list. You can then select the ID of the
group you want to call. Refer to “MAKING GROUP CALLS” on page 12 for details.
Tone
Press this key to turn the transceiver audible tones off. When active, you will
no longer hear tones from the transceiver. Press this key again to turn the
audible tones back on.
•
Zone Down
Press this key to decrease the zone number. Press and hold this key to cycle
down through the zone numbers. If programmed by your dealer, when the
lowest zone number is reached, the transceiver will “roll-over” to the highest
zone number and continue cycling down.
•
•
Zone Select
Using the CH control, turn clockwise to increase the zone number and
counterclockwise to decrease the zone number.
Zone Up
Press this key to increase the zone number. Press and hold this key to cycle
up through the zone numbers. If programmed by your dealer, when the
highest zone number is reached, the transceiver will “roll-over” to the lowest
zone number and continue cycling up.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
BACKGROUND OPERATIONS
Your dealer can activate a variety of transceiver functions to perform without any
additional operation on your part.
TIME-OUT TIMER (TOT)
The Time-out Timer is used to prevent any caller from using a channel for an
extended period of time.
If you continuously transmit for a period of time that exceeds the programmed
time, the transceiver will stop transmitting and an alert tone will sound. To stop
the tone, release the microphone PTT switch. Your dealer can program the TOT
time in the range of 15 seconds to 20 minutes.
If programmed by your dealer, a pre-alert tone will sound before the timer
expires. Also, if programmed by your dealer, you may have to wait for a short
duration before you can continue to transmit. If you press the microphone PTT
switch before the timer has been reset, an alert tone will sound and the
transceiver will not enter transmit mode.
COMPANDER
The compander is programmed only for specific (analog) channels. If it has
been programmed by your dealer, transmitted signals are compressed before
being sent and received signals are expanded when they arrive.
•
Your dealer must set the compander for both the transmit side and the receive side in
order for the compander to operate.
This background feature allows higher clarity of signals, avoiding excessive
noise and interference. This feature is not used on digital channels, as they are
not susceptible to noise and interference.
PTT ID
PTT ID is a unique transceiver ID code which is sent each time the microphone
PTT switch is pressed.
Note: PTT ID can be made only in FM Operation.
If Beginning of Transmit is set, the ID signal is transmitted when you press the
microphone PTT switch.
If End of Transmit is set, the ID signal is transmitted when you release the
microphone PTT switch.
If both are set, the ID signal is transmitted when you press and release the
microphone PTT switch.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
BUSY CHANNEL LOCKOUT (BCL)
If set up by your dealer, you will be unable to transmit on a conventional channel
if it is already in use. Under these circumstances, use a different channel or wait
until the channel becomes free.
However, if BCL Override has also been programmed, you can transmit overtop
of the current signal:
1 Press and hold the microphone PTT switch.
•
If the channel is already in use, a warning tone will sound.
2 Release the microphone PTT switch, then press and hold the microphone
PTT switch again within half a second.
3 Speak into the transceiver as you would during a normal transmission.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT
When using the optional VGS-1 voice guide & storage unit, you gain access to
the voice recorder and voice announcement functions. Ask your dealer for
details.
VOICE RECORDER
The voice recorder provides you with an auto recorder to record your
conversations and a voice memo function to create voice memos.
The voice recorder can store a combined maximum of 300 seconds (5 minutes)
of recordings in blocks of up to 30 seconds each.
■ AUTO RECORDING
If activated, the auto recording will continuously record all transmitted and
received signals. The recording storage area retains 30 seconds of
recording, so all transmitted and received signals are simultaneously
recorded and erased, leaving only the last 30 seconds of recording in
memory.
•
The auto recording indicator (KCH-14:
appears when this function is activated.
/ KCH-15:
)
■ VOICE MEMOS
To record a voice memo, for later playback:
1 Press and hold the key programmed as Playback for 1 second.
•
The duration of recording memory will appear on the display and begin
counting down.
2 Speak into the microphone to record your voice memo.
•
Pressing the microphone PTT switch at this time will transmit your message as
well as record it. Do not press the microphone PTT switch if you do not want to
transmit your message.
3 Press the PF 2, PF 4, or DTMF key to end the recording at any time and
store it into the transceiver memory.
•
•
•
Press the PF 1 key to cancel the recording at any time. The recording is not
stored to memory in this case.
If the memory becomes full, recording will stop automatically and store the
voice memo to memory.
“WRITING” appears on the display while the recording is being stored to
memory.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
■ PLAYBACK
To play back a recorded conversation, memo, or message:
1 Press the key programmed as Playback to enter Playback mode.
•
If the last action on your transceiver was to auto record your conversation,
“STORE?” will appear on the display, otherwise a memory channel with the
time of the recording will appear. To store the conversation record in the next
available memory channel, press the PF 4 key. To skip to the stored memory
channels, press the PF 2 or DTMF key. To skip back 5 seconds, press the
GRP
key. To skip ahead 5 seconds, press the GRP
key.
2 Press the GRP
memory channel you want to play back.
and
keys or rotate the CH control to select the
•
•
“AR” represents conversation records.
“VM” represents voice memos.
3 The transceiver will announce the channel, then the recording will
automatically play back.
•
•
When the entire recording has been played, “END OF MSG” (end of message)
is displayed.
To delete the selected recording, press the PF 3 or DTMF # key. To clear all
the recorded data, press and hold the PF 3 or DTMF # key. A confirmation
message will appear on the display. Press the PF 2 or DTMF key to delete
the recording(s) or the PF 3 or DTMF # key to cancel.
VOICE GUIDE
When changing the zone, channel, or operation mode, an audio voice will
announce the new zone, channel, or mode, after it has been selected. (Voice
Annunciation can be activated or deactivated by your dealer.)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|