27” (69 cm) Wide
LAUNDRY CENTER
Washer -
Dryer
Use and Care Guide
CENTRO DE LAVANDERÍA
de 27" (69 cm) de ancho
Lavadora - Secadora
Manual de Uso y Cuidado
P/N 134809700A (0703)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS LAUNDRY CENTERS:
Do not use or mix liquid chlorine
bleach with other household chemicals such as
toilet cleaners, rust removers, acid or products
containingammonia.Thesemixturescanproduce
dangerous fumes which can cause serious injury
or death.
Do not under any
circumstances cut,
remove, or bypass
Groundingtype
wall receptacle
thegroundingprong
from this plug
Power supply
cord with
3-prong
grounding plug
CORRECT
Use this way ONLY
Avoid fire hazard or electrical shock. Do not use an adaptor plug or extension cord or remove
grounding prong from electrical power cord. Failure to follow this warning can cause serious injury, fire
or death.
Important Safety Instructions
Read all instructions before using this laundry center.
You can be killed or seriously injured if you don't follow these Important Safety
Instructions:
• To reduce the risk of fire, electrical shock, or injury to persons when using this laundry center, comply with
the basic warnings listed below.
• Failure to comply with these warnings could result in serious personal injuries.
Prevent Fire
• Do not wash or dry items that have been previously cleaned in, soaked in, or spotted with gasoline, cleaning
solvents,kerosene,waxes,etc.Donotstoretheseitemsonornearthedryer. Thesesubstancesgiveoffvapors
that could ignite or explode.
• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a load to catch fire.
• Do not put oily or greasy rags or clothing on top of the laundry center. These substances give off vapors that
could ignite the materials.
• Donotaddgasoline,cleaningsolvents,orotherflammableorexplosivesubstancestothewashwater.These
substances give off vapors that could ignite or explode.
• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for
2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a
period, before using the washer, turn on all hot water faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen gas. Hydrogen gas is flammable; do not smoke or use
an open flame during this time.
• To prevent fire, do not use heat to dry items containing plastic, foam rubber or similarly textured rubber-like
materials, or items containing feathers or down. Use Air Fluff (No Heat) only.
• Cleanthedryerlintscreenbeforeoraftereachload.Theinteriorofthedryer,lintscreenhousingandexhaust
ductshouldbecleanedapproximatelyevery18monthsbyqualifiedservicepersonnel. Anexcessiveamount
of lint build-up in these areas could result in inefficient drying and possible fire. See Care and Cleaning.
• Do not operate the dryer if the lint screen is blocked, damaged or missing. Fire hazard, overheating and
damage to fabrics can occur. If your dryer has a drying rack, always replace the lint screen when finished
using the drying rack.
• Keep area around the exhaust opening and surrounding areas free from the accumulation of lint, dust and
dirt.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions Con't
• Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw rugs against the front or
back of the laundry center.
• Do not spray any type of aerosol into, on or near laundry center at any time.
• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the
fabric softener or product.
• Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or damage
to the rubber or plastic parts of the laundry center.
Protect Children
• Do not allow children to play on or in the laundry center. Close supervision of children is necessary when
thelaundrycenterisused nearchildren.Aschildrengrow,teachthemtheproper,safeuseofallappliances.
• Destroy the carton, plastic bag and other packing materials after the laundry center is unpacked. Children
might use them for play. Cartons covered with rugs, bedspreads or plastic sheets can become airtight
chambers.
• Keep laundry products out of children's reach. To prevent personal injury, observe all warnings on product
labels.
• Before the laundry center is removed from service or discarded, remove the washer lid and dryer door to
prevent accidental entrapment.
• Failure to comply with these warnings could result in serious personal injuries.
Prevent Injury
• To prevent shock hazard and assure stability during operation, the laundry center must be installed and
electrically grounded by a qualified service person in accordance with local codes. Installation instructions
are packed in the laundry center for the installer's reference. Refer to INSTALLATION INSTRUCTIONS for
detailed grounding procedures. If the laundry center is moved to a new location, have it checked and
reinstalled by a qualified service person.
• Topreventpersonalinjuryordamagetothelaundrycenter,theelectricalpowercordofagaslaundrycenter
must be plugged into a properly grounded system. Never ground the laundry center to a gas pipe.
Do not use an extension cord or an adaptor plug.
• Follow package directions when using laundry products. Incorrect usage can produce poisonous gas--
resulting in serious injury or death.
- Do not combine laundry products for use in 1 load unless specified on the label.
- Do not mix chlorine bleach with ammonia or acids such as vinegar.
• To prevent serious personal injury and damage to the laundry center:
- All repairs and servicing must be performed by an authorized servicer unless specifically
recommended in this Owner's Guide. Use only authorized factory parts.
- Do not tamper with controls.
- Do not install or store the laundry center where it will be exposed to the weather.
• ALWAYS disconnect the laundry center from the electrical supply before attempting any service or
cleaning. Failure to do so can result in electrical shock or injury.
• Do not use any type spray cleanser when cleaning dryer interior. Hazardous fumes or electrical shock could
occur.
• Topreventinjury,donotreachintothewasherwhilepartsaremoving. Beforeloading,unloadingoradding
items, push in the cycle selector knob and allow the tub to coast to a complete stop before reaching inside.
• To prevent injury, do not reach into the dryer if the drum is moving. Wait until the dryer has stopped
completely before reaching into the drum.
• A thermal limiter switch automatically turns off the dryer motor in the unlikely event of an overheated
situation(electricdryersonly). Aservicetechnicianmustreplacethethermallimiterswitchaftercorrecting
the fault.
• The washer is equipped with an electrical overload protector. The motor will stop if it becomes overheated
The washer will automatically restart after a cool down period of up to 30 minutes, if the washer has not
been manually turned off during this time.
• Failure to comply with these warnings could result in serious personal injuries.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Procedures
• Follow the guidelines below for preparing the wash load.
• Read the Washer Operating Instructions for operating your specific
model.
• Always read and follow fabric care and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons,
read Important Safety Instructions before operating this washer.
1. Sort laundry into loads that can be washed together.
Sort items by recommended water temperatures, wash time, and agitate/
spin speeds.
•
Separate white, light, and colorfast items from dark and noncolorfast
items.
Separateitemswhichshedlintfromitemswhichattractlint.Permanent
press, synthetic, knit and corduroy items will pick up lint from towels,
rugs and chenille bedspreads.
•
Sort laundry into loads that can be
washed together.
•
•
Separate heavily soiled items from lightly soiled items.
Separate lacy, sheer and loosely knit items from sturdy items.
2. Prepare items for washing.
•
•
•
Empty pockets.
Brush off lint and dirt. Shake out rugs and beach towels.
Close zippers, fasten hooks, tie strings and sashes, and remove
nonwashable trims and ornaments.
•
Remove pins, decorative buttons, belt buckles, and other objects
which could be damaged. This also helps protect other items in the
wash load.
•
•
Mend rips and tears to prevent further damage during washing.
Place delicate items such as bras, shoulder pads, hosiery, and belts in
a mesh bag to prevent tangling during the wash cycle.
Turn knit items inside out to prevent pilling.
Empty pockets.
•
3. Pretreat stains and heavy soil.
See Stain Removal for details.
4. Add a measured amount of detergent to the wash tub before
adding the laundry load.
Follow detergent manufacturer's directions. The amount required depends
on type of detergent, load size and soil level, and water hardness.
Place delicate items in a mesh bag.
5. If desired, add liquid bleach to Bleach Dispenser (some models).
• Before adding the wash load, add liquid bleach to bleach dispenser
located in left front corner under the lid:
•
•
•
3/4 cup (180 ml) for small loads
1 cup (240 ml) for large loads
1-1/4 cups (300 ml) for extra-large loads.
• Then add 1 cup (240 ml) water to flush the dispenser.
• Do not use powdered bleach in the bleach dispenser.
For models without a bleach dispenser, dilute the recommended
amount of liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash
water after a few minutes of agitation. Do not pour bleach directly on
wash load.
Bleach Dispenser (some models)
5
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Procedures con't
6. Add laundry load to washer.
• Dry load level should not be higher than the top of agitator vanes.
Do not overload the washer.
• Do not put items on top of agitator or wrap them around it. Load items
evenly.
• Combine large and small items in a load. Load large items first. Large
items should not be more than half the total wash load.
• When washing a single heavy item, add 1 or 2 towels to balance the
load.
Do not load items above
top of agitator vanes in wash tub.
7. If desired, add liquid fabric softener to Fabric Softener Dispenser
(available on some models).
For models with a built-in dispenser (see picture to the left):
1. Add liquid softener to the dispenser, following fabric softener label
directions.
2. Add water to bring liquid level to fill line on dispenser cap.
3. Remove the dispenser from the agitator after each use. Rinse both
cap and cup with warm water. Replace dispenser in the agitator.
Built-In Fabric Softener Dispenser
(some models)
NOTE: To separate cap from cup, put thumb into dispenser and push
against side of cup (see picture to the left). After cleaning, push cap and
cup firmly together. Replace dispenser by lining up the ribs and grooves
and snapping it into position. If fabric softener builds up in or around the
dispenser, clean the area with hot water.
DO NOT REMOVE SERVICE CAP FOUND INSIDE THE AGITATOR
POST.
For models without a fabric softener dispenser, follow fabric softener
label directions. Add diluted fabric softener to the final rinse. Do not pour
fabric softener directly on the wash load.
Built-In Fabric Softener Dispenser
(some models)
8. Select cycle and settings according to type, size, and soil level of
each load
See Operating Instructions for your specific model controls.
9. Start the washer.
DO NOT REMOVE
SERVICE CAP
FOUND INSIDE
THE AGITATOR
POST.
Close the washer lid and pull out the cycle selector knob. The washer will
not agitate or spin with the lid open.
• To stop the washer, push in the cycle selector knob.
• To change a cycle, push in the cycle selector knob. Turn it clockwise
to the desired setting. Pull out the knob to restart the washer.
10. Remove items when the cycle is completed.
For your safety, the lid locks when the tub is spinning. It will remain locked
for 2-3 minutes after the tub stops spinning.
•
To open the lid during a spin, push in the cycle selector knob and wait
about 2-3 minutes for the lid lock to release. Do not force open the
locked lid.
Place washed items in automatic dryer, line dry, or dry flat as directed by
fabric care label. Excess wrinkling, color transfer or odors may develop in
items left in the washer after the cycle has ended.
To avoid serious personal injury, do not operate washer if safety
lid lock is missing or damaged.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safe Stain Removal Procedures
To reduce the risk of fire, electrical shock, or serious injury to persons
Stain Removal
or property, comply with the basic warnings listed in Important Safety Instructions
and those listed below.
•
•
Read and comply with all instructions on stain removal products.
Keep products in their original labeled containers and out of children's
reach.
•
•
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine
bleach. Dangerous fumes may result.
•
Never wash items which have been previously cleaned in, washed in,
soaked in or spotted with gasoline, dry cleaning solvents or other flammable
or explosive substances because they give off vapors that could ignite or
explode.
Do not combine stain removal products.
•
Never use highly flammable solvents, such as gasoline, inside the home.
Vapors can explode on contact with flames or sparks.
For successful stain removal:
•
•
Remove stains promptly.
Determine the kind of stain, then follow recommended treatment in the
stain removal chart on the next page.
•
To pretreat stains, use a prewash product, liquid detergent, or a paste made
from granular detergent and water.
•
•
•
•
Use cold water on unknown stains because hot water can set stains.
Check care label instructions for treatments to avoid on specific fabrics.
Check for colorfastness by testing stain remover on an inside seam.
Rinse and wash items after stain removal.
Follow fabric care label instructions.
STAIN
TREATMENT
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
Adhesive tape, chewing gum,
rubber cement
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.
Baby formula, dairy products,
egg
Pretreat stain. Wash using cold water and bleach safe for fabric.
Beverages (coffee, tea,
soda,juice, alcoholic beverages)
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Blood
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is
absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable
dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Candle wax, crayon
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Chocolate
Collar or cuff soil, cosmetics
Dye transfer on white fabric
Grass
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse thoroughly. Wash
using hottest water safe for fabric.
Grease, oil, tar (butter, fats,
salad dressing, cooking oils,
car grease, motor oils)
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Ink
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly
mildewed fabrics may be permanently damaged.
Mildew, scorch
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Mud
Mustard, tomato
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL
BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly before washing.
Paint, varnish
Perspiration
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for
fabric.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
Rust, brown or yellow
discoloration
LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric. Pretreat
with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area.
Wash using bleach safe for fabric.
Shoe polish
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
Urine, vomit, mucus, feces
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Washing Problems
Manywashingproblemsinvolvepoorsoilandstainremoval,residuesoflintandscum,andfabricdamage.Forsatisfactorywashing
results, follow these suggestions provided by The Soap and Detergent Association.
SOLUTIONS
PROBLEM
PREVENTIVE MEASURES
•Add detergent before wash load. Then
start washer.
•Add fabric softener to dispenser (available
on some models).
•Dilute fabric softener with water.
POSSIBLE CAUSES
•Detergent or liquid fabric softener
did not dissolve or disperse.
•If caused by detergent, mix 1 cup (240
ml) white vinegar with 1 quart (.95 L)
water in a plastic container. Soak item 1
hour. Rinse.
•If caused by fabric softener, rub stains
with bar soap. Wash.
Blue stains
•Sort items by soil level and color.
•Use correct amount of detergent, hottest
water and bleach safe for fabric
•Use correct amount of detergent and
hottest water safe for fabric.
•Do not pour liquid fabric softener
directly on fabric. See package directions
or Washing Procedures for proper
diluting.
•Rewash with correct amount of
detergent and hottest water safe for
fabric. Add bleach safe for fabric.
•Treat with prewash stain remover or
liquid detergent.
•Increase detergent and water
temperature. Rewash.
•Rub fabric softener stains with bar soap.
•Not enough detergent.
•Wash water temperature too
low.
Discoloration,
graying
•Incorrect sorting.
•Not enough detergent.
•Undiluted liquid fabric softener
poured directly on fabric.
Greasy, oily stains
•Never pour chlorine bleach directly on
fabric.
•Check condition of items before washing.
See Washing Procedures for preparing
and loading the wash load.
•May be irreversible if rips, tears and
seams cannot be mended.
•Incorrect use of chlorine bleach.
•Unfastened zippers, hooks,
buckles.
•Rips, tears and broken threads.
•Overloading the washer.
•Degradation of fabric.
Holes, tears, or
snags
•See Washing Procedures for sorting and
preparing the wash load.
•Do not overload washer.
•Use correct amount of detergent, water
temperature and water level.
•Reduce load size. Rewash using correct
water temperature, water level, and
amount of detergent.
•Add nonprecipitating water conditioner
to wash water.
•Add liquid fabric softener to final rinse.
•Dry load in dryer.
•Remove lint with lint brush or roller.
•Incorrect sorting.
•Tissues left in pocket.
•Overloading the washer.
•Not enough detergent.
•Undissolved detergent has left
residue.
Lint
•Static cling is attracting lint.
•Load washed too long
•Use fabric softener in the washer to
lubricate fibers.
•When ironing, use spray starch or fabric
finish on collars and cuffs.
•Use a lint brush or shaver to remove
pills.
•Pilling is normal with synthetic and
permanent press fabrics. This is
due to abrasion from normal
wear.
Pilling
(Fibers break off,
ball up and cling to
fabric)
•Turn items inside out to reduce abrasion.
•Increase water temperature using hottest
water safe for fabric.
•Do not overload washer.
•Use liquid detergent or use
nonprecipitating water conditioner with
nonphosphate granular detergent.
•Reduce load size.
•Add dissolved detergent to tub . Rewash
load.
•Mix 1 cup (240 ml) white vinegar to 1
gallon (3.8 L) warm water in plastic
container. Soak item. Rinse and rewash.
•Undissolved detergent.
•Some nonphosphate granular
detergents can combine with
hard water minerals to form a
residue.
Residue or powder
on dark items;
Stiff, harsh fabrics.
•Do not overload washer.
•Remove items from washer as soon as
cycle is completed.
•Reduce load size.
•Rinse in cold water with liquid fabric
softener.
•Overloading the washer.
Wrinkling
•Use liquid fabric softener.
•Wash synthetics frequently hot water
and correct water level.
•Soak in detergent booster or product
containing enzymes.
•Wash in hot water using full permanent
press cycle. Increase detergent.
•Add bleach safe for fabric or, treat with
color remover.
•Agitation time too short.
•Wash water temperature too
low.
Yellow buildup of
body soil on
synthetic fabrics
•Not enough detergent.
•Use nonprecipitating water softener.
•Before washing, run hot water for a few
minutes to clear lines.
•Drain water heater occasionally.
•For an ongoing problem, install an iron
filter in your water supply system.
•To restore discolored load of whites, use
rust remover safe for fabric.
Do not use chlorine bleach to remove
rust stains. It may intensify
discoloration.
•Iron or manganese in water
supply, water pipes, or water
heater.
Yellow or brown
rust stains
8
Download from Www.Somanuals.com. All Manuals Search And Download.
• Follow the guidelines below for preparing the load for drying.
Drying Procedures
• Read the Dryer Operating Instructions for operating your specific model.
• Always read and follow fabric care labels and laundry product labels.
Toreducetheriskoffire, electricalshock, orseriousinjurytopersons
orproperty,complywiththebasicwarningslistedin ImportantSafetyInstructions
and those listed below.
1. Prepare items for drying.
•
Dry items of similar fabric, weight and construction in the same load.
•
Separate dark items from light-colored items. Separate items that shed lint
from those that attract lint. If an item sheds lint, turn it inside out.
•
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum
finish.Closezippers,fastenhooksandVelcro®-likefasteners.Tiestringsand
sashes to prevent snagging and tangling.
•
•
If possible, turn pockets inside out for even drying.
Follow fabric care label instructions.
Check for stains which may not have been removed in washing. Dryer heat
may permanently set some stains. Repeat stain removal process before
drying.
•
Place small items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
3. Load the dryer.
•
•
•
•
•
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble
freely for even drying and less wrinkling. Do not overload dryer.
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall
and medium sized items.
For delicate or very small loads, add 2 lint-free towels for better drying, less
wrinkling, and to prevent grease stains caused by fabric softener sheets.
Place small items in a mesh bag.
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,
and a build-up of static electricity, which can produce more lint.
If desired, add a dryer fabric softener sheet.
4. Close the dryer door and set dryer controls (some models).
See Dryer Operating Instructions card for your specific model controls.
5. Select cycle and settings according to type of load, level of
dryness and/or options desired.
6. Start the dryer.
•
Turn Start control clockwise to ON. Hold for 1-2 seconds and release.
•
Toaddorremoveitemswhenthedryerisrunning,openthedoor.Thedryer
will always stop when the door is opened.
•
Allow the drum to come to a complete stop before reaching inside.
Fill dryer drum 1/3 to 1/2 full.
7. When the cycle ends, remove items immediately and hang
or fold. If load is removed before the cycle ends, turn cycle selector to OFF.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cycle Signal Control (some models)
Features
WhentheCycleSignalControlisON, asignalwillsoundattheendofeachcycleand
during the Press Saver setting (some models). The volume is adjustable on some
models.
Drum Light (some models)
Adrumlightwillcomeonwheneverthedoorisopenedtoilluminatethedryerdrum
during loading and unloading. Closing the door turns off the light.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1. Open the dryer door and remove the lint screen.
2. Insertdryingrackintothedryerdrum. Placethefrontbarunderthelipofthelint
screen opening.
3. Place items to be dried on top of rack. Weight should not exceed 10 lbs. Leave
space between items, but do not let items hang over the sides or through the
grids. Do not tumble other items when using the drying rack.
4. Selectatimeddrysettingbestsuitedforitemsbeingdried. UseonlytheAirFluff
(noheat)temperaturesettingforitemscontainingplastic,foamrubber,rubber-
like materials, feathers or down.
5. When items are dry, remove the rack and replace the lint screen. If lint screen
isnotinplace,tumblingitemscouldentertheexhaustsystemandcausedamage
to the dryer.
Use the drying rack to dry items which should
not be tumbled.
Common Drying
Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PREVENTIVEMEASURES
•Add a few bath towels to small loads for proper
tumbling.
•Some "silk-like" fabrics should be air dried.
•Use proper drying temperature.
•Place fabric softener sheet on top of load before
starting the dryer.
PROBLEM
Greasy, oily
stains
POSSIBLECAUSES
SOLUTIONS
•Fabric softener sheet.
•Rub fabric softener stains with bar
soap.
Rinse and rewash.
•Do not overload dryer.
•Use fabric softener in washer or dryer to reduce
static electricity.
•Remove items when they are slightly damp to
avoid overdrying.
•Check that lint screen is clean and in place.
• Overloading.
• Overdrying causes static
electricity.
•Lint screen not clean when
cycle began.
•Lint is attached to "pills."
•Reduce load size and rewash using
liquid fabric softener in the final rinse.
•Or, add a fabric softener sheet and
tumble without heat.
Lint
•Use lint brush or roller to remove lint.
•Use fabric softener to lubricate fibers.
•When ironing, use spray starch or fabric finish on
collars and cuffs.
•Pilling is normal with
synthetic and permanent
press fabrics. This is due to
abrasion from normal
wear.
•Use a lint brush or shaver to remove
pills.
Pilling
(Fibers break off,
ball up and cling
to fabric.)
•Turn items inside out to reduce abrasion.
•Follow fabric care label directions.
•If shrinking is a concern, check load often.
•Remove items while slightly damp.
•Block knits into shape.
•Overdrying.
•Irreversible condition.
Shrinking
Wrinkling
•Lay flat to complete drying.
•Overloading.
•Leaving items in dryer after
cycle ends.
•Reduce load size and tumble at
medium or low heat for 5-10 minutes.
•Remove items immediately. Hang or
fold.
•Do not overload dryer.
•Remove items as soon as cycle ends.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To reduce risk of fire or serious injury to persons or property, comply
with the basic warnings listed in Important Safety Instructions and those listed
below.
Care and Cleaning
•
Beforecleaningthewasherordryerinterior,unplugtheelectricalpowercord
to avoid electrical shock hazards.
•
Do not use any type spray cleanser when cleaning dryer interior. Hazardous
fumes or electrical shock could occur.
Inside the Washer
•
•
•
•
Removeitemsfromthewasherassoonasthecycleends.Excesswrinkling,color
transfer, and odors may develop in items left in the washer.
Dry the washer top, the area around the lid opening, and the underside of the
lid. These areas should always be dry before the lid is closed.
Beforecleaningthewasherinterior,unplugtheelectricalpowercordtoavoid
electrical shock hazards.
When extremely soiled items have been washed, a dirty residue may remain on
the tub. Remove this by wiping the tub with a nonabrasive household cleanser.
Rinsethoroughlywithwater.
Clean lint screen after every load.
•
The agitator or tub may become stained from fabric dye. Clean these parts with
a nonabrasive household cleanser. This prevents dye transfer to future loads.
Inside the Dryer
•
Clean the dryer lint screen after every load. Lint build-up in the screen restricts
air flow, which causes longer drying times. The screen is located at the bottom
ofthedooropening.Removebypullingstraightup.Removethelintandreplace
the screen.
•
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added
fabric softener sheets. To remove this build-up, wash the lint screen in warm,
soapy water. Dry thoroughly and replace. Do not operate the dryer without the
lint screen in place.
Wash lint screen occasionally.
•
•
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith
a damp cloth and a mild liquid household cleanser. Remove cleanser residue
before drying the next load.
Use care with laundry
products. They can damage finish on
the laundry center.
Every 18 months a Sears or other qualified service dealer should clean the
dryer cabinet interior and exhaust duct. These areas can collect lint and dust
overtime. Anexcessiveamountoflintbuild-upcouldresultininefficientdrying
and possible fire hazard.
Outside
•
When laundering is completed, wipe cabinet with a damp cloth. Turn water
faucets off to prevent pressure build-up in the hoses.
•
Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasivecleansers.Ifthecabinetbecomesstained,cleanwithdilutedchlorine
bleach [1/2 cup (120 ml) in 1 quart (.95 L) water]. Rinse several times with clear
water.
•
Remove glue residue from tape or labels with a mixture of warm water and mild
detergent. Or, touch residue with the sticky side of the tape or label.
•
Beforemovingthelaundrycenter,placeastripofcardboardorthinfiberboard
under the front leveling legs to prevent floor damage.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WinterizingInstructions
Ifthelaundrycenterisstoredinanareawherefreezingcanoccurormovedinfreezing
temperatures,followthesewinterizinginstructionstopreventdamagetothelaundry
center:
FollowWinterizing
Instructions for cold
weather care.
1. Turn off water supply faucets.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1 gallon nontoxic recreational vehicle (RV) antifreeze to empty wash tub.
Close lid.
5. Set cycle selector knob at a spin setting. Pull out knob and let washer spin for 1
minute to drain out all water. Not all of the RV antifreeze will be expelled.
6. Push in knob, unplug electrical power cord, dry tub interior, and close lid.
7. Store washer in an upright position.
8. To remove antifreeze from washer after storage, run empty washer through a
complete cycle using detergent. Do not add wash load.
Avoid Service Checklist
Before calling for service, review this list. It may save both time and expense. The list includes common concerns that are not the
result of defective workmanship or materials in this laundry center.
SOLUTION
OCCURRENCE
POSSIBLE CAUSE
WASHER - NOISE
"Clunking" or gear sounds.
This is normal.
A certain amount of "clunking" or gear
sounds are normal in a heavy-duty
washer.
Rattling and clanking noise.
Stop washer and check tub. If noise continues after
washer is restarted, objects may be in pump. Call Sears
or other qualified service dealer.
Foreign objects such as coins or safety
pins may be in tub or pump.
To prevent unnecessary noise and damage to tub,
fasten fasteners and turn items inside out.
Belt buckles and metal fasteners are
hitting wash tub.
Squealing sound or hot
rubber odor.
Do not overload washer. Stop washer and reduce load.
Washer is overloaded.
Thumping sound.
This is usually normal. If sound continues, washer is
probably out of balance. Stop washer and redistribute
wash load.
Heavy wash loads may produce a
thumping sound.
Move laundry center so it rests firmly on solid floor.
Additional floor bracing may be needed. Adjust leveling
legs. See INSTALLATION INSTRUCTIONS for details.
Laundry center is not resting on a solid,
firm floor.
Vibrating noise.
See INSTALLATION INSTRUCTIONS for removing
shipping bolt and block.
Shipping bolt and block have not been
removed during installation.
Stop washer and rearrange wash load.
Wash load unevenly distributed in tub.
WASHER - OPERATING
Washer does not start.
Close washer lid
Washer lid is open
Make sure plug fits tightly in wall outlet.
Electrical power cord may not be plugged
in or connection may be loose.
Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If problem is a circuit overload, have it
corrected by a qualified electrician. If problem is a
power outage, call local electric company.
Housefuseblown, circuitbreakertripped,
or a power outage has occurred.
Turn on water supply faucets.
Water supply faucets are not turned on.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
WASHER - OPERATING
(continued)
Move indicator clockwise slightly. Pull out knob.
Washer does not start
(continued).
Cycle selector is not in correct position.
Motor is overheated.
Washer motor will stop if it becomes overheated. It will
automatically restart after a cool down period of up to
30 minutes (if washer has not been manually turned
off).
Close lid completely. Safety lid lock must not be broken.
Washer won't spin.
Residue left in tub.
Lid is not completely closed.
Heavily soiled items.
Wipe tub with a nonabrasive household cleanser, then
rinse. Shake or brush excess dirt and sand from items
before washing.
WASHER - WATER
Do not overload washer. See Washing Procedures.
Rearrange load to allow proper spinning.
Straighten drain hose.
Wash load too wet after Washer is overloaded.
spin.
Load is out of balance.
Drain hose is kinked.
Check another faucet in the house. Wait until water
supply and pressure increase.
Water does not enter Water supply is not adequate in area.
washer or it enters slowly.
Fully open hot and cold faucets.
Water supply faucets are not completely open.
Water is being used elsewhere in the house.
Water pressure must be at least 30 psi (260 kPa). Avoid
running water elsewhere while washer is filling.
Straighten hoses.
Water inlet hoses are kinked.
Do not overload washer. When control is set at highest
fill level, dry load level should not be higher than top row
of circular holes in wash tub.
Water level does not cover Washer is overloaded.
load.
Measure hot water temperature at nearby faucet with
candy or meat thermometer. Water temperature should
be at least 120°F (49°C). Adjust water heater as
necessary.
Warm or hot water is not Hot water heater is set too low or is a
hot enough.
distance from laundry center.
Avoid using hot water elsewhere before or during
washer use. There may not be enough hot water
available for proper cleaning. If problem persists, your
hot water system may be unable to support more than
1 use at a time.
Hot water is being used elsewhere in
the house.
See Operating Instructions for your washer
To conserve energy, the temperature of
the hot wash is regulated.
Clean and straighten the drain hose.
Water in washer does not Drain hose is kinked or clogged.
drain or drains slowly.
Check and tighten hose connections. Install rubber
sealing washers provided.
Water leaks.
Loose fill hose connection at faucet or
washer.
Unclog drain pipes. Contact plumber if necessary.
Use less detergent.
House drain pipes are clogged.
Oversudsing.
Connect hot water hose to hot water faucet and cold
water hose to cold water faucet.
Incorrect wash and rinse Hot and cold water hoses are connected
temperatures. to wrong supply faucets.
Standpipe must be a minimum of 33" (83.82 cm) high
to prevent siphoning. See INSTALLATION
INSTRUCTIONS.
Water is entering washer Drain hose standpipe is incorrect height.
but tub does not fill.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OCCURRENCE
DRYER
POSSIBLE CAUSE
SOLUTION
Electrical power cord is not securely
plugged in or plug may be loose.
Make sure the plug fits tightly in wall outlet.
Dryer does not start.
House fuse blown or circuit breaker
tripped.
Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded and the dryer
is on a separate circuit.
Thermal limiter tripped.
Call a Sears or other qualified service dealer for
replacement.
There are 2 house fuses in the dryer
circuit. If 1 of the 2 fuses is blown, the
drum may turn but the heater will not
operate.
Replace fuse.
Dryer runs but won't
heat.
Gas supply valve is not open (gas models).
Check to make sure supply valve is open. See
INSTALLATION INSTRUCTIONS for procedure.
Dryer does not have enough air supply to
support the burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has
been a utility interruption of natural gas
(gas models).
Refill or replace tank.
Dryer should heat when utility service is restored.
Lint screen is clogged with lint.
Make sure all lint has been removed from the dryer lint
screen before starting each cycle.
Drying cycle takes too
long, outsideofthedryer
feels too hot or smells
hot.
Exhaust duct requirements have not been
met.
Exhaust duct must be at least 4 inches in diameter and
made of rigid or flexible metal.
When in place, the duct must have no more than two
90° bends and must not exceed length listed in
INSTALLATION INSTRUCTIONS.
Electric dryer is connected to a 208 volt
circuit.
Drying time will be 20% longer than drying on a 240 volt
circuit.
Drying procedures have not been
followed.
See Drying Procedures.
Outside exhaust hood or exhaust duct
may be clogged or restricted.
Clean out any obstruction.
High humidity.
Use a dehumidifier near the dryer.
Do not overload. See Drying Procedures.
Remove items as soon as cycle ends.
See Drying Procedures.
Excessive wrinkling.
Dryer is overloaded.
Items left in dryer too long.
Insufficient sorting of items.
Drying temperature too high.
Follow fabric care label instructions.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Kenmore Appliance Warranty
One Year Limited Warranty
When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due
to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME®
(1-800-469-4663)toarrangeforfreerepair.
If this appliance is used for other than private family purposes, this warranty applies for only 90 days from the date of
purchase.
This warranty covers only defects in material and workmanship. Sears will NOT pay for:
1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product installation, operation or maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with
the product.
5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.
6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.
Disclaimer of implied warranties; limitation of remedies
Customer’s sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied
warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest
period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not
allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties
of merchantability or fitness, so these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United States and Canada.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8
Master Protection Agreement
Congratulations on making a smart purchase. Your new Kenmore® appliance is designed and manufactured for years of
dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That’s when
having a Master Protection Agreement can save you money and aggravation.
The Master Protection Agreement also helps extend the life of your new appliance. Here’s what’s included in the Agreement:
√
Parts and labor needed to help keep products operating prop-erly under normal use, not just defects. Our coverage
goes well beyond the product warranty. No deductibles, no functional failure excluded from
coverage— real protection.
√
Expert service by a force of more than 10,000 authorized Sears service technicians, which means someone you can
trust will be working on your product.
√
√
Unlimited service calls and nationwide service, as often as you want us, whenever you want us.
“No-lemon” guarantee – replacement of your covered product if four or more product failures occur within twelve
months.
√
√
√
Product replacement if your covered product can’t be fixed.
Annual Preventive Maintenance Check at your request – no extra charge.
Fast help by phone – we call it Rapid Resolution – phone sup-port from a Sears representative on all products. Think of
us as a “talking owner’s manual.”
√
√
Power surge protection against electrical damage due to power fluctuations.
$250 Food Loss Protection annually for any food spoilage that is the result of mechanical failure of any covered
refrigerator or freezer.
√
√
Rental reimbursement if repair of your covered product takes longer than promised.
10% discount off the regular price of any non-covered repair service and related installed parts.
Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day
or night, or schedule a service appointment online.
The Master Protection Agreement is a risk free purchase. If you cancel for any reason during the product warranty period, we will
provide a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Master Protection
Agreement today!
Some limitations and exclusions apply.
For prices and additional information,
call 1-800-827-6655 in the U.S.A. or Canada
call 1-800-4-MY-HOME®.
Sears Installation Service
For Sears guaranteed professional installation of home
appliances and items like garage door openers and water
heaters, in the U.S.A. call 1-800-4-MY-HOME®
Download from Www.Somanuals.com. All Manuals Search And Download.
|