V.NETWORKS
READ ME FIRST
VN-C11
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
This READ ME FIRST is made from 100 % recycled paper.
Model No.
Serial No.
VN-C11
LWT0105-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Due to design modifications, data given in this
instruction book are subject to possible change
without prior notice.
FOR USA AND CANADA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCETHE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSETHIS APPLIANCETO RAIN
OR MOISTURE.
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK. DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE.REFER
SERVICING
TO
QUALIFIED SERVICE PERSONNEL.
AVERTISSEMENT:
The lightning flash wish arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the pres-
ence of uninsulated "dangerous volt-
age" within the product's enclosure that
may be of sufficient magnitude to con-
stitute a risk of electric shock to per-
sons.
POUR EVITER LES RISQUES
D’INCENDIE OU D’ELECTRO-
CUTION, NE PAS EXPOSER
L’APPAREIL A L’HUMIDITE OU A LA
PLUIE.
The exclamation point within an equi-
lateral triangle is intended to alert the
user to the presence of important op-
erating and maintenance (servicing)
instructions in the literature accompa-
nying the appliance.
INFORMATION (FOR CANADA)
RENSEIGNEMENT (POUR CANADA)
This Class A digital apparatus complies with
Canadian ICES-003.
Information for USA
This device complies with part 15 of the FCC Rules.
Changes or modifications not approved by JVC could
void the user’s authority to operate the equipment.
Cet appareil numérique de la Class A est
conforme á la norme NMB-003 du Canada.
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own
expense.
Information for Europe
Warning:
This is a class A product. In a domestic environment
this product may cause radio interference in which
case the user may be required to take adequate
measures.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Thank you for purchasing this product.
(These instructions are for VN-C11U.)
Before beginning to operate this unit, please read the instruction manual carefully in
order to make sure that the best possible performance is obtained.
Contents
Contents................................................................................................. 4
Introduction
Features ................................................................................................. 5
Items Included ........................................................................................5
Required Operating Environment........................................................... 6
Upgrading the Application ......................................................................6
Operating Precautions ........................................................................... 7
Controls, Connectors and Indicators...................................................... 8
Connection Examples .......................................................................... 10
Preparations
Preparation Procedure ......................................................................... 11
Step 1 Connection and Installation
Attaching a Lens ................................................................................12
Connecting the Power Cord ............................................................... 13
Connecting a LAN Cable ................................................................... 14
Installing the Camera ......................................................................... 15
Step 2 Setting the Network
Installing the Software ....................................................................... 16
Setting the PC’s IP Address for Windows XP .................................... 17
Setting the PC’s IP Address for Windows 2000 ................................. 19
Setting the IP Address for VN-C11 with V.Networks Setup Tool ........ 21
Registering the Connected Camera with V.Networks Controller ................... 23
Step 3 Adjusting the Camera
Back-focus Adjustment ...................................................................... 24
Step 4 Setting with V.Networks Controller
Starting Up V.Networks Controller ..................................................... 25
Function Settings with V.Networks Controller .................................... 26
Operations
Step 5 Operations with V.Networks Controller
Operations with V.Networks Controller .............................................. 27
Step 6 Operations with a Web Browser
Required Operating Environment ...................................................... 28
Access Authorization ......................................................................... 29
Starting Up the Web Browser ............................................................ 30
Specifications ..................................................................................... 31
Others
External Dimensions ......................................................................... 31
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Features
• VN-C11 uses a 1/3-inch CCD with 380,000 pixels, enabling monitoring of high quality images.
• For the compression method, in addition to the standard JPEG, VN-C11 supports MPEG4 for a
wide range of bit rates. (With MPEG4, up to 4 clients can be connected at one time.)
• Equipped with an image recording function by motion detection and alarm input.
• VN-C11 has a design similar to other CCTV monitoring cameras, allowing peripheral equipment
for such cameras to be also used for VN-C11.
• With a built-in Web server, VN-C11 supports Internet Explorer and Netscape.
• Multicast function. (Only for JPEG)
Items Included
CD-ROM
(The PDF instruction manual inside) Read Me First Warranty Card Service Information Card
How to Use This Manual
Characters and Symbols used in this Manual
Caution
Operational points special attention should be paid to, because of, for example,
danger involved.
Note
Functional or operational tips.
☞
Pages or items to refer to.
❈ In no case, shall JVC be held liable for any loss or damage to the customer or for any claim
from any third party arising from using this software.
For the purpose of improving the product, the software specifications are subject to change
without prior notice.
The product names that appear in this document are brand names or registered trademarks
of each relevant company. Marks and symbols such as ™, ® and © do not appear in this
document.
To see the content of the PDF instruction manual inside the supplied CD-ROM,
it is required that the Adobe Acrobat Reader is installed in the PC.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Introduction
Required Operating Environment
PC Specifications
OS
: Windows 2000 (Service Pack 1 or higher)
Windows XP Home Edition
Windows XP Professional
CPU
: Pentium III 500 MHz or higher (1 GHz or higher recommended)
Memory Capacity
Hard Disk Space
Display/Video Card
: 128 MB or more
: 20 MB or more
: 1024 X 768 pixels or more, True Color (24 bits or 32 bits)
LAN Specifications
• 10 BASE-T/100 BASE-TX network connected with IEEE802.3 hubs.
Note
The PC specifications above are only for a reference purpose. They are not meant to guaran-
tee a smooth operation of the application software. Depending on the usage of the PC, there
may be cases where problems occur even if the PC satisfies the technical requirements.
Caution
If the OS specifications of the PC to be used are higher, they precede those described above.
Upgrading the Application
For information on upgrading the application, visit the following website.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Precautions
● VN-C11 designed for indoor use. For outdoor use, prepare a proper housing to cover and protect
the camera.
● The product should not be installed or used in the following locations.
• Locations subject to rain or water.
• Locations with hot air or oil vapors such as in kitchens, etc.
• Locations where the allowed ambient temperature (0 °C to 40 °C) is exceeded.
• Locations exposed to X-ray radiation or where strong electrical or magnetic waves are gener-
ated.
• Locations where corrosive gas is generated.
• Locations with vibrations.
• Locations with excessive dust.
● If VN-C11 and the cables connected to VN-C11 are installed at a location where strong electrical
or magnetic waves are generated, near a radio, TV set, transformer, motor etc., the quality of
image and color may be affected.
● If a high-intensity object (such as a lamp) is shot, the image on the screen may have vertical lines
(smear) or blur (blooming) at its periphery.This is a characteristic of the CCD, and is not a defect.
● Clean the unit with the power turned off. Use a soft cloth like cotton flannel to wipe out dirt. Do not
use paint thinner or benzine as a cleaning agent as this may cause melting or tarnishing of the
unit surface. If dirt is persistent, use a cloth soaked with water-diluted mild detergent and then
wipe it with a dry cloth.
● Because the cable holders of the terminals could come loose, perform cable connection carefully
and securely.
● Insufficient dissipation of heat from the unit may cause damage. Use the unit at a well-ventilated
location. In particular, do not block the unit’s cooling-fan ventilation opening.
● In a narrowband environment, for example, of dial-up connection, smooth running of MPEG4
images cannot be obtained. This is due to the product design, therefore not a defect.
● When this product is installed in an NAT environment, MPEG4 images cannot be viewed. This is
due to the product design, therefore not a defect. (This product uses a network protocol called
RTP for transmitting MPEG4 images. Generally, an NAT router cannot carry out NAT translation
of RTP packets properly.)
● Certain hubs and switches equipped with SNMP functions have a broadcast or multicast control
function. If the function is enabled, multicast images created by this product may not be viewed
properly.
● To save electricity, turn off the power to the system when not in use.
● As local recording images are saved to the volatile memory of the product, the images are
deleted if the power is turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Introduction
Controls, Connectors and Indicators
(Front, top and side views)
2
1
3
4
5
8
7
6
1 Lens mount
5 Screw hole (1/4-20UNC)
For attaching the camera to
a fixer or a pan/tilt unit. The
screw length must not ex-
ceed 7 mm. If a longer screw
is used, the internal parts of
the camera may be dam-
aged.
The mount for attaching a lens. Either a C-
mount or a CS-mount lens can be used.
2 Back-focus adjustment ring
MAX.
7 mm
The ring for adjusting back-focus and chang-
ing the mount method. For adjusting back-fo-
cus or changing the mount method, loosen
the back-focus locking screw (3) by turning it
counterclockwise and, after the operation, fix 6 Fall-preventive holes
it by turning it clockwise. At the factory, VN-
C11 is optimized for attaching a CS mount
lens.
For installing the camera securely, use these
holes to prevent it from falling off.
7 Screws for the bracket (x 2: M2.6 X 6 mm)
Screws of the length of 6 mm should be used.
A longer screw may damage the internal parts.
3 [BF LOCK] locking screw
This serves to fix the back focus-adjustment
ring.
8 [MAC address]
4 Bracket for camera mounting.
Physical address unique to the unit. Cannot
be changed.
At the factory, the bracket is attached on the
bottom of the camera. According to the instal-
lation condition, this can be attached at the
top. Use the screws (7) for attaching the
bracket to the camera.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls, Connectors and Indicators (continued)
(Side and rear views)
9
#
$ %
!
0
1
2
OUT COM
G
2
1
ALARM
PUSH
RESET
IRIS
@
POWER MONITOR OUT
10BASE-T/100BASE-TX
DO NOT CONNECT TO THE
TELEPHONE NETWORK
For USA
&
^
9 Ventilation opening
# [DC 12 V/AC 24 V] Power terminal
For the internal cooling fan. Install the cam-
era in a way that does not cover the opening.
For connecting to a DC 12V or AC 24V, 50 Hz/
60 Hz, power source. (☞ Page 13)
0 [RESET] button
$ [ALARM INPUT] terminals
Press this button to reset VN-C11. If this but-
ton is held down for 2 seconds or longer, the
values set with [V.Networks Setup Tool] re-
turn to those set at the factory, and VN-C11
restarts.
For connecting with an external alarm equip-
ment.
% [ALARM OUTPUT] terminals
For connecting with an external alarm equip-
ment.
! [IRIS] terminal
For connecting with a DC IRIS lens.
(A video iris lens cannot be connected.)
^ [10 BASE-T/100 BASE-TX]
For network connection with a LAN cable.
(☞ Page 14)
@ [POWER] indicator
This indicator starts blinking when the power
is turned on. When the camera is ready for
network connection, this becomes steady on.
If the indicator blinks while the camera is in
use, check the camera and/or the network
equipment.
& [MONITOR OUT] terminal
For connecting to monitor TV when deciding
camera angles.
Caution
For angle adjustment only, problems such
as noise may occur if connected with a
switcher.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Preparations
Connection Examples
LAN Connection
VN-C11
MAC address
BF LOCK
LAN
VN-C11
MAC address
PC
BF LOCK
Network Connection
VN-C11
MAC address
BF LOCK
VN-C11
MAC address
BF LOCK
LAN
INTERNET
FTP Server
PC
Images are automatically
PC
updated at a regular interval.
Peer-to-Peer Connection
VN-C11
MAC address
BF LOCK
PC
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation Procedure
Set the camera in the following procedure.
Step 1 Connection and Installation
Attach a lens and connect the power cable, a LAN cable and an alarm etc.
Then, install the camera to a fixer, etc. Fix a wire securely for preventing the
camera from falling off.
☞ Page 12
After installing the camera, connect the MONITOR OUT terminal located on
the rear panel to the monitor TV and adjust the camera angle.
(For back-focus adjustment, ☞ Page 24)
Step 2 Setting the Network
Install the software [V.Networks Controller], and set the network for the PC
and VN-C11. Also perform the setting with [V.Networks Setup Tool] and regis-
tration of the connected camera with [V.Networks Controller].
☞ Page 16
❈ If multiple PCs are in use, first turn on the power for one PC and proceed to Other
Settings with V.Networks Setup Tool. Only then, turn on the power to a second PC
and go on to Other Settings with V.Networks Setup Tool. Repeat the procedure for
other PCs. Refer to the PDF instruction manual inside the supplied CD-ROM.
Step 3 Adjusting the Camera
Adjust the back-focus while checking images.
☞ Page 24
Step 4 Setting with V.Networks Controller
Set image quality and alarm, etc. by using [V.Networks Controller] which has
been installed.
☞ Page 25
Step 5 Operations with V.Networks Controller
Now the camera is ready for recording and playback, etc. with [V.Networks
Controller].
☞ Page 27
☞ Page 28
Step 6 Operations with a Web Browser
The camera is ready for Web operations.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Preparations (Step 1 Connection and Installation)
Attaching a Lens
Attach a lens in the following procedure.
1. Before attaching a lens, check the mount
method of the lens.
VN-C11 is set for CS-mount at the factory. For
attaching a C-mount lens, loosen the back-
focus locking screw using a screwdriver and
turn the back-focus adjustment ring to change
the mount method accordingly with a finger
or a pointed tool like a screwdriver.
To attach a lens, observe the length shown
as (a). Do not use a lens with a length longer
than (a) as it may cause damage to the inter-
nal parts of the camera and proper lens at-
(a)
F
tachment would not be possible.
Lens
Flange-back distance (b) Length (a)
(b)
C-mount lens
CS-mount lens
17.526mm
12.5mm
10 mm max.
5.5 mm max.
2.
RESET
IRIS
2. Attach the lens to the camera securely by turn-
ing it clockwise.
3.
1
3
4
3. In the case of a DC IRIS lens, connect the
lens cable to the socket while examining the
pin arrangement.
2
4-Pin Plug
DC IRIS Lens
Lens
(Without a built-in EE amplifier)
Pin No.
1
2
3
4
Damping d
Damping e
Driving e
3
1
Driving d
4
2
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Cord
Connect the camera to DC 12 V or AC 24 V.
The power indicator is lit when the power is turned
on.
To
Power
Power Cord
• Do not connect the power cord to DC 12 V and
AC 24 V at the same time.
• Use a lug plate to securely connect the power
cord to the power terminals and avoid
misconnection or loose connection.
• For DC 12 V connection, ensure that the
polarities, positive and negative, are correctly
oriented.
1
2
OUT COM
G
2
1
ALARM
• For DC 12 V connection, the ripple voltage
should not exceed 50 mV.
PUSH
Power
indicator
lamp
Length: 30 m maximum
UL1007, UL1015 or equivalent
AWG #20 or equivalent, or higher
POWER MONITOR OUT
10BASE-T/100BASE-TX
DO NOT CONNECT TO THE
TELEPHONE NETWORK
For USA
WARNING
Connect with the appropriate power-supply voltage.The rated voltage for VN-C11 is DC 12 V
or AC 24 V, 50 Hz/60 Hz. If a voltage exceeding the rating is supplied, malfunction, or in the
worst case, fuming or fire, may be caused.
For AC 24 V, ensure that the primary side is insulated with the secondary one.
For a system with multiple VN-C11s
In a system where more than one VN-C11 are used, turn on the power for a VN-C11 first and
proceed the setting to Other Settings with V.Networks Setup Tool. Only then turn on the power for a
second one and go on to Other Settings with V.Networks Setup Tool. Repeat the procedure for the
other cameras. Refer to the PDF instruction manual inside the supplied CD-ROM.
Note
The IP address of VN-C11 is set to “198.168.0.2” at the factory. Proper access cannot be
established due to IP address redundancy if the power is turned on for multiple cameras at
one time under a single LAN environment. Do not turn on the power for multiple cameras
at the same time. If an IP address redundancy occurred, ensure that only one VN-C11 exists
on a single LAN environment and wait for some time (at least 10 minutes). Or turn off the
power once for all network equipment and turn it on again for proper access to VN-C11.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Preparations (Step 1 Connection and Installation)
Connecting a LAN Cable
Connect the camera to a hub or a PC by using a LAN cable.
• For hub connection
Use a straight cable.
OUT COM
G
2
1
• For PC connection
Use a cross-over cable.
ALARM
PUSH
Caution
POWER MONITOR OUT
10BASE-T/100BASE-TX
There are a few types of LAN board for
which a cross-over cable cannot be used.
Check the specifications of the LAN board
to be used before performing connection.
DO NOT CONNECT TO THE
TELEPHONE NETWORK
For USA
Note
For 100 BASE-TX, use a CAT-5 cable.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Camera
Fall-Preventive wire
For attaching the camera to a fixer or a rotating platform, use the screw hole of the
mounting bracket.
Camera mounting
screw hole
Camera-mounting bracket
Caution
● The length of the screw for
mounting the camera must
not exceed 7 mm. Do not
use a longer screw as it
may damage the internal
parts of the camera.
MAX.
7 mm
● In the factory setting, the
bracket is attached on the
top of the camera. For attaching it at the
bottom, remove the two screws fixing the
bracket.
Fall-preventive holes Screws for the bracket
[x 2: M2.6 x 6 mm]
Securing wire
M2.6 x 4 mm
Caution
For fixing the bracket, screws of the length
of 6 mm should be used. Do not use a
longer screw as it may damage the internal
parts of the camera.
4 mm
2 mm
[Fall Prevention]
WARNING
• Special care is required if the camera is installed on a wall or ceiling. You should not attempt
to install it by yourself as it may cause injury or an accident. This installation work should be
carried out only by qualified and experienced personnel.
• When the camera is attached to a fixer or a pan/tilt unit, use the holes for fall prevention to
secure it.
• To prevent the camera from falling off, secure it to a secure and stable structure such as a
ceiling slab or a channel by using a wire.
• Ensure that the length, strength, routing and material (insulation) of the securing wire to be
used are appropriate.
• To attach the securing wire, use the black screw on the top side of the camera.
• For fixing the wire, a screw of M2.6 X 4mm should be used. Do not use a longer screw as it
may damage the internal parts of the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Preparations (Step 2 Setting the Network)
Installing the Software
For operatingVN-C11, install the software from the CD-ROM, which is supplied with
~~~~~~~~~~~~~~~
the camera in the following procedure.
Installing V.Networks Controller
1. Select [Setup.exe] found in the [JVC] folder.
2. Proceed by following the instructions shown on the screen.
3. If the installation is successfully executed, the [V.Networks] icon is created in [Programs] of the
Windows [Start] menu.
[V.Networks Controller] is displayed in [V.Networks].
Installing V.Networks Setup Tool
1. Open the [JVC] folder and then the “setup” folder inside. Select [Setup.exe].
2. Proceed by following the instructions shown on the screen.
3. If the installation is successfully executed, the [V.Networks] icon is created in [Programs] of the
Windows [Start] menu.
[vn-c11u Setup Tool] is displayed in [V.Networks].
Installing DirectX 8.1 and Codec
[DirectX 8.1] and ISO MPEG4 Codec are required for viewing MPEG4 images with VN-C11. If the
version currently installed in the PC is older, install the version 8.1 by following the procedure below.
Installing Codec
Select [WMPCD8.exe] and install Codec by following the instructions shown on the screen.
Installing DirectX 8.1
1. Click [Start] and select [Run]. And enter [dxdiag] in the box and click [OK].
2. If the version is older, select [DX81NTeng.exe] and follow the instructions on the screen.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the PC’s IP Address for Windows XP
After attaching the camera, proceed to set the IP address of the PC by which the
camera is operated.
With Windows XP, follow the procedure below to set the IP address.
(For Windows 2000, ☞ Page 19)
Note
Under a DHCP environment and also if the IP address to be allotted to [V.Networks] is already
known, skip Setting the PC’s IP Address.
1.Click
.
• Right-click [My Network] and select [Properties].
2.Select the network connected to the PC by which VN-C11 is operated.
• Right-click to select [Properties].
Ensure that [Client for Microsoft Networks]
is selected
.
Note
If either [Client for Microsoft Networks]
or [Internet Protocol (TCP/IP)] is not
displayed, select [Install ...].
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Preparations (Step 2 Setting the Network)
Setting the PC’s IP Address for Windows XP (continued)
3. Select [Internet Protocol (TCP/IP)] and click [Properties].
Select [Internet Protocol (TCP/IP)].
Click [Properties].
4. Select [Use the following IP address] to set [IP Address] and [Subnet Mask] and then click
.
Select [Use the following IP address].
Set [IP Address] to “192.168.0.3.”
Note
● Before changing the IP address,
note down the original address.
● Do not use the same IP address
elsewhere in this network environ-
ment.
Set [Subnet Mask] to an appropriate value
according to the operating environment.
Ask the network administrator if necessary.
Click
.
5. Click
18
in [Local Area Connection Properties].
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the PC’s IP Address for Windows 2000
After attaching the camera, proceed to set the IP address of the PC by which the
camera is operated.
With Windows 2000, follow the procedure below to set the IP address.
1. Click
.
Select [Settings] and click [Control Panel].
2. Double-click [Network and Dial-up Co...].
3. Double-click [Local Area Connection].
Select [Internet Protocol (TCP/IP)].
Click [Properties].
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Preparations (Step 2 Setting the Network)
Setting the PC’s IP Address for Windows 2000 (continued)
4. Click [IP Address] in [TCP/IP properties].
Select [Use the following IP Address].
Set the IP address to “192.168.0.3.”
Set [Subnet mask] to an appropriate value
according to the operating environment. Ask
the network administrator if necessary.
5. Click
.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the IP Address for VN-C11 with V.Networks Setup Tool
Set the IP address for VN-C11 by using the installed [V.Networks Setup Tool].
(With this [V.Networks Setup tool] onlyVN-C11, not other models, can be connected.)
Caution
● After the power for VN-C11 is turned on, there will be about 20 seconds until VN-C11 be-
comes ready to be connected with the PC. This is not a defect.
● At the factory, DHCP is set enabled for VN-C11.
● About the DHCP function
JVC does not recommend operatingVN-C11 with this function enabled because a different
IP address may be assigned upon the renewal of the leasing contract. The DHCP function
of VN-C11 is designed for simplifying the installation and setting procedures.
Note
For connecting VN-C11 with the factory settings, either one of the environments described
below is required.
● Environment where no DHCP server exists.
● Environment where a DHCP server exists, which clearly defines the allotted IP address and
MAC address.
1. Select [Start], [Programs], [V.NETWORKS] and then
[V.Networks Setup Tool].
[vn-c11u Setup Tool] to start up
Enter the IP address of the camera to be
connected to [Connection IP Address].
The IP address is set to 192.168.0.2 at
the factory.
Click
.
Note
Click [Search] to see the IP address of the connected camera.
The [V.Networks Search] screen is dis-
played.
To start search, click [Search].
[V.Networks IP Address List] is dis-
played.
● [TimeOut] is for setting the time for searching (0 to 30 seconds).
If no IP address is displayed by searching, change the value to a longer one and then search
again.
● If [V.Networks] on LAN has a different subnet from that of the PC, connection cannot be
established even if the IP address of the camera can be searched and found. Reconnect the
camera after changing the IP address of the PC accordingly.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Preparations (Step 2 Setting the Network)
Setting the IP Address for VN-C11 with V.Networks Setup Tool (continued)
2. Confirm the settings.
Select whether to use DHCP.
Note
● With DHCP selected, the IP ad-
dress of the DHCP server etc. can
be checked.
Change the IP address to the one alloted,
or approved, by the network administrator.
Set the subnet mask to an appropriate
value according to the operating environ-
ment.Ask the network administrator if nec-
essary.
Click
.
[V.Networks ID] works as an identifica-
tion code set to VN-C11. Only alphanu-
meric characters can be used. This ID
does not directly affect the operation by
the user. Normally, the ID should be set
as “CAM00001,” “CAM00002” etc.
(0 to 8 characters)
For other settings, refer to the PDF
instruction manual inside the supplied
CD-ROM.
3. Click
.
Click
to update the values.
Note
A new IP address becomes effective
when VN-C11 is automatically reset.
4. Start up [V.Networks Controller]. (☞Page 23)
Note
In a system where more than one VN-C11 are used, turn on the power for a VN-C11 first and
proceed the setting to Other Settings with V.Networks Setup Tool. Only then turn on the power
for a second one and go on to Other Settings with V.Networks Setup Tool. Repeat the proce-
dure for the other cameras. Refer to the PDF instruction manual inside the supplied CD-ROM.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering the Connected Camera with V.Networks Controller
The connected camera can be registered with the installed [V.Networks Controller].
1. Select [Start], [Programs], [V.NETWORKS] and then
up [V.Networks Controller].
[V.Networks Controller] to start
Select [File] and [New].
2. [New] is displayed.
Enter 198.168.0.2 in [IP Address].
Note
In a DHCP environment, enter the IP
address allotted by the DHCP server.
Enter [V.Network Name], a name under which
the camera is registered. Use a name that is
easy to remember, such as the installation
location or number. (1 to 40 characters)
Recording files of the name given in
saved in a designated folder here.
are
You can set whether VN-C11 automatically
starts recording upon connection.
Note
For connecting VN-C11 with the factory settings, either one of the environments described
below is required.
• Environment where no DHCP server exists.
• Environment where a DHCP server, which clearly defines the IP address and MAC address
allotted to VN-C11, exists.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Preparations (Step 3 Adjusting the Camera)
Back-focus Adjustment
At the factory, back-focus is set at the point for the widest range of use for
CS-mount. However, it is necessary to readjust back focus if a zoom or C-mount
lens is used or if focus cannot be attained using the focus ring of the lens. To
adjust, follow the procedures described below.
In order to adjust back-focus appropriately, use the iris adjustment function and an ND filter to re-
lease the lens iris before proceeding with the adjustment. (An ND filter acts to reduce the overall
amount of light entering the lens equally over all wavelengths.)
Connect the MONITOR OUT terminal on the rear panel to the monitorTV.To adjust,
follow the procedures described below.
<For a fixed-focus lens>
Back focus
adjustment ring
If focus cannot be attained using the focus ring of
the lens, adjust the back-focus as follows.
1. Loosen the back-focus lock screw by turning
it counterclockwise with a Phillips screwdriver.
2. Aim the camera at the object or a spot of detail
somewhere away from the object while
checking the image on the PC screen.
3. Turn the focus ring to .
Tighten
Loosen
4. Turn the back-focus adjustment ring to
optimize the focus.
5. Tighten the back-focus lock screw securely by
turning it clockwise.
Back focus locking
screw (M2.6)
Lens focus ring
<For a zoom lens>
If the image gets out of focus when zoomed in/
out, adjust the camera as follows:
1. Loosen the back-focus locking screw by
turning it counterclockwise with a Phillips
screwdriver.
2. Aim the camera at the object or a spot of detail
somewhere away from the object while
checking the image on the PC screen.
3. Zoom in the lens and adjust the focus by
turning the focus ring.
4. Zoom out the lens and adjust the focus by
turning the focus ring.
5. Repeat steps 3 and 4 a few times.
6. Tighten the back-focus locking screw securely
by turning it clockwise.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations (Step 4 Setting with V.Networks Controller)
Starting Up V.Networks Controller
With the installed Controller, camera images can be monitored. The settings for
recording, replay and frame rate etc. can also be performed.
1. Select [Start], [Programs], [V.NETWORKS] and then
up [V.Networks Controller].
[V.Networks Controller] to start
In the pull down menu, select the camera
to connect.
Caution
After the power for VN-C11 is turned
on, there will be about 20 seconds until
VN-C11 becomes ready to be con-
nected with the PC. This is not a de-
fect.
Live images from the camera are dis-
played.
Note
• If a password has been set, enter the correct password.
• This [Controller] can be connected to VN-C1, VN-C2, VN-C3, VN-C30 (only for JPEG), VN-
A1, VN-C10 and VN-C11.
• In the MPEG4 mode, up to 4 clients can be connected at one time. If 5 or more clients are
connected, the message “The VN-C11U has not start the Streaming Service.” appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Operations (Step 4 Setting with V.Networks Controller)
Function Settings with V.Networks Controller
With [V.Networks Controller], settings for image size, alarm etc. can be performed.
1 2 3 4
1 File
3 Setting
New
: Creates a new file if
the camera is con-
nected for the first
time.
Quality
: Sets the compression
rate and image qual-
ity.
Framerate
: Sets the number of
frames transmitted
per second.
Delete
: Deletes a file.
Motion Detect Standby : For selecting the
camera for which
Alarm Reg
Alarm
:
If this is selected
alarm operation will
be enabled.
,
motion detection is
enabled.
Exit
: Exits “Controller.”
: Alarm actions for
each alarm can be
set individually.
2 View
Image Size
: Sets the image dis-
play size.
JPEG : 640x480
320x240
160x120
MPEG4 : 320x240
160x120
Time Stamp
Property
: Sets display of the
date and time of file
saving.
:
Changes information
on cameras not cur-
rently connected.
Upside Down
: Displays the image
inversely. This func-
tion is used in the
case that the camera
is inversely installed.
(Not available for
MPEG4)
4 Help
About
:
For checking the ver-
sion of [V.Networks
Controller].
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations (Step 5 Operations with V.Networks Controller)
Operations with V.Networks Controller
[V.Networks Controller] can be used to select the camera, record and playback the
camera images etc.
(The Controller screens are identical with those for otherV.Networks models. Certain
functions are not available for VN-C11.)
1
6
Not available for VN-C11.
2 3 4
5
1 Camera
4 REC
Displays the name of the connected camera.
When this is selected, recording starts. The
It is also possible to select the camera using
recorded files are saved under the name
shown in 1. During recording, the display
[Recording in progress] appears in 1. The
display [REC] will also appear on the displayed
image.
the
pull down menu.
2 PLAY
Select the file saved in 4 and replay. Select
this button too for replaying a recorded file with
an alarm activated.
5 SNAPSHOT
Saves only one frame of the image being
displayed.
3 STOP
Stops recording.
6 SIZE
Reduces the size of the [V.Networks Controller]
screen. (See below.)
Reduced screen
1
Camera
Press here to enlarge.
For details, refer to the PDF instruction manual inside the supplied CD-ROM.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Operations (Step 6 Operations with a Web Browser)
It is possible to view still/moving images and perform various settings via not only
the provided [Controller] software but via a Web browser as well.
However, note that MPEG4 files cannot be viewed with a browser. Also, the browser
does not support the image inversion function.
Required Operating Environment
The following environment is required for viewing and operating VN-C11 with a Web browser.
It is necessary for the PC to satisfy the technical requirements described in this
instruction manual (☞ Page 6).
The PC must also satisfy the following Web browser conditions:
• A Web browser compatible with JavaScript and frame, that is, Netscape Ver. 4.x or Internet
Explorer Vers. 4.x, 5.x and 6.x.
• For the recommended CPU performance and required memory capacity, refer to theWeb browser
in use.
For smooth display of large-screen moving images, specifications much better than those rec-
ommended are necessary.
Images from the camera will not be displayed properly in the 256-color mode.
• For Internet Explorer, an environment where Java can be properly run (Microsoft VM) is re-
quired.
LAN Environment
• VN-C11 can work as a web server that uses HTTP. Access linkage using a host name is pos-
sible if the environment supports DNS (Domain Name System).
• A direct connection of VN-C11 to a PC is possible using a cross-over cable. (Though rare,
certain LAN boards do not allow the use of a cross-over cable. Be sure to check your LAN
board.)
Note
Web page images
Web page images shown in this document refer to Web page data within VN-C11, including
images captured by the VN-C11 camera and displayed by a Web browser.
Depending on the type and settings of the Web browser, the page format and character fonts
of the displayed Web pages may vary. Should the page contents fail to be displayed in total, try
resizing the window, etc.
The illustrations in this manual are obtained from Internet Explorer display screens.
For Internet Explorer
• After the password has been changed, the password authentication window may ask for the
password twice. In this case, enter the same password twice.
For Netscape Navigator
• When a moving image from VN-C11 is displayed, the page content cannot be updated by
changing the window size. In this case, click the [Update] button on the Netscape window to
update the page display.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Access Authorization
The structure of URLs within the VN-C11 is as shown below.
Security level
<User>
<Operator>
<Administrator>
Top page
(index-e.html)
(still-e.html)
Still image page
Moving image page (java-e.html)
Still image URL (still.jpg)
Serverpush moving image
URL (push.jpg)
Configuration page (javaconfig-e.html)
Configuration menus
Image Quality Configuration (configimage-e.html)
View Configuration (viewconfig-e.html)
Alarm Configuration (alarm-e.html)
FTP Configuration (ftp-e.html)
Java moving image URL
(mjpeg.class)
Other Configurations (config-e.html)
This page is intended for linkages to other VN-C11 web pages.
Verifying access authorization
If passwords are set, the [User Name and Password] request window appears (for access
authorization).
User name is not used.
Enter any one of the three passwords that have
been set.
Click
.
Note
• It is recommended that you register the URL (Uniform Resource Locator).
• For speedy display of the VN-C11 web pages on your web browser, it is recommended that
you register the URL information during the access test using the set IP address or DNS
host name.
• For this purpose, use the [Favorites] function of Internet Explorer or, in the case of Netscape,
[Bookmarks].While the VN-C11 web page is displayed in the browser, use the [Add] function
to bookmark the page.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Operations (Step 6 Operations with a Web Browser)
Starting Up the Web Browser
Start up the web browser. Specify the factory-set web page address of VN-C11.
(With the factory-set IP address entered, the web browser displays the VN-C11 top
page.)
Note
If a proxy server is set for accessing the Internet, there are cases in which the IP address
cannot be directly specified. In this case, change the proxy setting so that the address can be
entered.
1. Start up the Web browser.
Note
In this instruction manual, the [Top page] and the [Home page] are defined as follows:
Top page
: The “/index-e.html” page
Home page : The specified page displayed when the default page function is enabled.When
the function is not enabled, the [Top page] is displayed.
2. The VN-C11 top page appears.
VN-C11 still image
The image taken in at the point when brows-
ing starts is displayed.
Buttons linking to other web pages.
(Click to jump to these pages.)
Caution
If the image mode of VN-C11 is MPEG4, the blue screen appears.
For details, refer to the PDF instruction manual inside the supplied CD-ROM.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Specifications
LAN standard
IEEE802.3, IEEE802.3u
Communication protocol
TCP/IP, UDP, HTTP, FTP, ICMP, ARP, RTP, RTSP, DHCP,
NTP
Monitor output
Image pickup device
Available pixels
Composite video x 1 (75 Ω, 1 Vp-p)
1/3 type IT CCD
Approx. 380,000 pixels (768 (H) x 494 (V))
50 dB (50 %, AGC OFF, Compression rate: 1)
2.5 lx (50 %, F1.2, AGC ON)
JPEG, MPEG4
640 x 480, 320 x 240, 160 x 120
640 x 480 not available for MPEG4
C/CS mount
Non-voltage “A” contact input. NPN open collector input.
Low level, latch/momentary (500 ms minimum)
Low level circuit current: 0.6 mA
High level impressed voltage: 3.3 V
NPN open collector output (allowable impressed voltage:
12 V, allowable input current: 300 mA)
RJ-45 (Category 5)
Video S/N ratio
Minimum required illumination
Image compression
Output image format
Lens mount
Alarm input
Alarm output
Network interfaces
10BASE-T/100BASE-TX (Auto-Negotiation)
8 MB
DC 12 V or AC 24 V, 50 Hz/60 Hz
1.2 A max.
0 °C to 40 °C
Approx. 560 g
Internal memory
Power supply voltage
Power consumption
Operating temperature
Mass
External Dimensions
U1-32
(Unit: mm)
148
138
70
MAC address
BF LOCK
42
71
1/4 – 20UNC
41
● Design and specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
VICTOR COMPANY OF JAPAN, LIMITED
® is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.
® is a registered trademark in Japan, the U.S.A., the U.K. and many other countries.
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
Printed in Japan
LWT0105-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
|