®
ROCK MONITOR SPEAKER
RM10
OWNER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER CONNECTIONS
CONNECTION TIPS
When Two RM10’s
Are Used
center post is visible under
the collar. Insert the bare end
RIGHT
LEFT
of the wire through this hole;
then screw the collar down
until the connection is tight.
The hole in the center of each
collar is intended for use with
banana-type connectors. To
comply with European CE
certification, these holes are
blocked with plastic inserts at
the point of manufacture. To
use banana-type connectors
requires the removal of the
inserts. Do not remove these
inserts if you are using the
product in an area covered by
the European CE certification.
Speakers and electronics
have corresponding positive
(+) and negative (–) terminals.
It is important to connect both
speakers identically: positive
(+) on the speaker to positive
(+) on the amplifier and nega-
tive (–) on the speaker to neg-
ative (–) on the amplifier.
Wiring “out of phase” results
in thin sound, weak bass and
a poor stereo image when
two speakers are used.
–
+
–
+
–
+
–
+
LEFT
RIGHT
Receiver or Amplifier Speaker Outputs
When One RM10 Is
Used
–
+
To use the binding-post
–
+
speaker terminals, unscrew
the colored collar until the
pass-through hole in the
Receiver or Amplifier
Speaker Outputs
TRIM CONTROLS
The RM10 monitor is equipped
with left and right high-fre-
quency trim controls that con-
trol the tweeters in the left
and right side panels of each
RM10 speaker. The trim con-
trols enable you to compen-
sate for various room condi-
driver. Turning the knob clock-
wise decreases the driver’s
level. Adjust the trim controls
so that the vocals are loud
enough to be intelligible with-
out being so loud as to be
harsh or distorted.
tions and vocal styles. Begin
by turning the knobs in the
center of each control as far
counterclockwise as they will
go. This is the normal level of
the associated high-frequency
TROUBLESHOOTING
If there is no sound
off as volume is
increased:
• Turn off all electronics
from any of the
and switch the speaker in
question with one of the other
speakers that is working cor-
rectly. Turn everything back
on and determine whether the
problem has followed the
speaker, or has remained in
the same channel. If the prob-
lem is in the same channel,
the source of the problem is
most likely with your receiver/
amplifier, and you should
consult the owner’s manual
for that product for further
information. If the problem
has followed the speaker,
consult your dealer for further
assistance or, if that is not
for further information.
speakers:
• Check all wires and connec-
tions between receiver/
amplifier and speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
• Check that receiver/ampli-
fier is on and that a source is
playing.
• Review proper operation of
your receiver/amplifier.
If there is no sound
coming from one
speaker:
• Check the “Balance” control
on your receiver/amplifier.
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers. Make sure
no wires are touching other
wires or terminals and creat-
ing a short circuit.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
If there is no (or low)
bass output:
• Make sure the polarities
(+ and –) of the left and right
“Speaker Inputs” are con-
nected properly.
• Consider adding a powered
subwoofer to your system.
If the system plays at
low volumes but shuts
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
RM10
3-Speaker, 2-way 10" (250mm) vocal monitor
Description
Maximum Recommended Amplifier Power*
Power Handling (Continuous/Peak)
Nominal Impedance
175W
50W/400W
8 Ohms
Sensitivity (2.83V/1m)
92dB
Frequency Response (–3dB)
Crossover Frequency
40Hz – 20kHz
1,700Hz
High-Frequency Transducers
Low-Frequency Transducer
Dual 3" (75mm) cones with high-temperature voice coils
10" (250mm) Cone with high-temperature
voice coil, shielded
™
Baffle
Low diffraction, IsoPower
™
Ports
Dual FreeFlow flared
™
™
Network
Straight-Line Signal Path (SSP )
with left and right high-frequency trim controls
Terminals
Gold-plated, 5-way binding posts
13-3/16" x 20-7/8" x 9-5/8" (335mm x 530mm x 245mm)
29.7 lb/13.5kg
Dimensions (H x W x D)
Weight per Speaker
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau du Loir
France
declare in own responsibility that the product described in
this owner’s manual is in compliance with technical stan-
dards:
STEAL THE SHOW.
EN 61000-6-3:2001
EN 61000-6-1:2001
GO PRO™
.
Laurent Rault
Harman Consumer Group International
Chateau du Loir, France 10/05
™
PRO SOUND COMES HOME
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 USA
8500 Balboa Boulevard, Northridge, CA 91329 USA
2, route de Tours, 72500 Chateau du Loir, France
*
The maximum recommended amplifier power rating will ensure
proper system headroom to allow for occasional peaks. We do
not recommend sustained operation at these maximum power
levels.
© 2005 Harman International Industries, Incorporated. All rights reserved.
JBL and Harman International are trademarks of Harman International Industries,
Incorporated, registered in the United States and/or other countries.
Part No. PRE1986
All features and specifications are subject to change without
notice. All dimensions include grilles.
Download from Www.Somanuals.com. All Manuals Search And Download.
|