DVD / HDD VIDEO RECORDER &
VIDEO CASSETTE RECORDER
DR-MX1S
CABLE/DBS
TV
DVD
STANDBY/ON
DVD
TV/
VHS
TIMER
VIDEO TV/CBL/DBS
VHS
HDD
DVD
TV VOLUME
CH
CANCEL
LIVE
AUX
MEMO/MARK
EDIT
DUBBING
PROGRAM
TV MUTING
TOP MENU
MENU
NAVIGATION
RETURN
ENTER
PREVIOUS
SLOW
NEXT
SLOW
PLAY/SELECT
CLEAR
STOP/
REC
PAUSE
JUMP
REC MODE
REMAIN
DISPLAY
ON SCREEN
SET UP
RAM/RW
For Customer Use:
Enter below the Model No. and
Serial No. which are located on the
rear of cabinet. Retain this
INSTRUCTIONS
information for future reference.
Model No.
Serial No.
LPT0975-001C
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
EN
3
ANTENNA INSTALLATION INSTRUCTIONS
Important product safety
instructions
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product,
be sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Electrical energy can perform many useful functions. But improper
use can result in potential electrical shock or fire hazards. This
product has been engineered and manufactured to assure your
personal safety. In order not to defeat the built-in safeguards,
observe the following basic rules for its installation, use and
servicing.
2. Lightning
ATTENTION:
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning
and power-line surges.
Follow and obey all warnings and instructions marked on your product
and its operating instructions. For your safety, please read all the safety
and operating instructions before you operate this product and keep
this booklet for future reference.
3. Power Lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them
might be fatal.
INSTALLATION
1. Grounding or Polarization
(A)Your product may be equipped with a polarized alternating-
current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a
safety feature.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
(B)Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source indicated
on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power
company. If your product is intended to operate from battery
power, or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered.
● Do not block the openings by placing the product on a bed, sofa, rug
or other similar surface.
● Do not place the product in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
4
EN
USE
SERVICING
1. Servicing
1. Accessories
To avoid personal injury:
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
● Do not place this product on an unstable cart, stand, tripod, bracket,
or table. It may fall, causing serious injury to a child or adult, and
serious damage to the product.
● Use only with a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with the product.
● Use a mounting accessory recommended by the manufacturer and
follow the manufacturer’s instructions for any mounting of the
product.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore
the product to its normal operation.
● Do not try to roll a cart with small casters across thresholds or deep-
pile carpets.
2. Product and Cart Combination
A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
3. Water and Moisture
Do not use this product near water—for
example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet
basement, or near a swimming pool and
the like.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
3. Replacement Parts
4. Object and Liquid Entry
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock or other hazards.
Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the product.
5. Attachments
Do not use attachments not recommended by the manufacturer of
this product as they may cause hazards.
4. Safety Check
service technician to perform safety checks to determine that the
product is in safe operating condition.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
● All major sections and subsections are listed in the Table Of
Contents on page 6. Use this when searching for information on a
specific procedure or feature.
7. Heat
The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
● The Index on pages 12 – 15 illustrates the controls and connections
on the front and rear panel, the front display panel and the remote
control.
● The list of terms on page 97 lists frequently-used terms, and the
number of the page on which they are used or explained in the
manual.
● The ੬ mark signals a reference to another page for instructions or
related information.
major section.
BEFORE YOU INSTALL YOUR NEW UNIT . . .
. . . please read the sections/literature listed below.
● “Cautions” on page 2
● “Important product safety instructions” on pages 3 – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
EN
5
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
Declaration of Conformity
Model Number:
Trade Name:
DR-MX1S
JVC
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, remote control or disc/cassette.
1. DO NOT place the unit —
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
— in an environment prone to extreme temperatures or
humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are
generated.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
— on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions—just as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
● Manufactured under licence from Dolby Laboratories. “Dolby” and
double-D symbol are trademarks of Dolby Laboratories.
● “DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems, Inc.
● VCR Plus+, C3 and PlusCode are registered trademarks of Gemstar
Development Corporation.
ATTENTION:
To mobile phone users:
Using a mobile phone in the vicinity of the unit may cause picture
vibration on the TV screen or change the screen to a blue back
display.
The VCR Plus+ system is manufactured under license from Gemstar
Development Corporation.
● DSSTM is an official trademark of DIRECTV, Inc., a unit of GM
Hughes Electronics. DISH NetworkTM is a trademark of Echostar
Communications Corporation.
On placing the unit:
● This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is intended for home
and other limited viewing users only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
Some TVs or other appliances generate strong magnetic fields.
Do not place such appliances on top of the unit as it may cause
picture disturbance.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
6
EN
SAFETY FIRST
2
About Discs....................................................................................7
INDEX
INITIAL SETTINGS
Plug & Play Set ............................................................................20
Language .....................................................................................21
EDITING
Monitor Set...................................................................................26
REMOTE CONTROL
78
BASIC OPERATIONS ON DVD DECK
27
Playback Features .......................................................................28
SYSTEM CONNECTIONS
80
Tray Lock (DVD Deck Only) ........................................................ 85
BASIC OPERATIONS ON HDD DECK
Format A Disc (DVD Deck Only) ................................................. 87
Finalize A Disc (DVD Deck Only) ................................................ 88
BASIC OPERATIONS ON VHS DECK
Basic Recording...........................................................................53
APPENDIX
LIST OF TERMS
97
TIMER RECORDING ON HDD/DVD DECK
55
WARRANTY (Only in U.S.A.)
FOR SERVICING (Only in U.S.A.)
98
3
VCR Plus+ C ® Timer Programming ...........................................55
Manual Timer Programming.........................................................57
Automatic Satellite Program Recording
100
(HDD Deck Only)......................................................................59
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
7
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0.
About Discs
Recordable/Playable Discs
You can use discs with the following logos for recording and
playback.
When a DVD-R/RW disc (Video mode) is finalized (੬ pg. 88), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
When a DVD-RW disc (VR mode) is finalized (੬ pg. 88), it can be
played back on a standard DVD player compatible with the VR
mode of DVD-RW discs.
Before finalizing —
— it is possible to record on unrecorded areas of the disc, edit the
disc title and program titles, and delete programs.
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalized.
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
DVD-RAM
DVD-RW
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0/2x speed
Ver. 2.1/1x – 2x speed
12 cm: 4.7 GB/9.4 GB
Ver. 1.1/1x – 2x speed (Video
mode/VR mode)
After finalizing —
After a DVD-R/RW disc (Video mode) has been finalized, it is
possible to play back the recorded programs (video and/or audio)
on a standard DVD video player as a DVD VIDEO disc.
● Edited titles are displayed as the
“DVD menu” in video mode.
● It is impossible to record, edit or
delete the data either in video
mode or in VR mode.
● Either in video mode or in VR
mode, although the disc can be
played back on DVD players from
DVD-R
12 cm: 4.7 GB
8 cm: 1.4 GB
Ver. 2.0/1x – 4x speed (Video
mode)
● The above table is based on the information as of February 2004.
● Recording and playback may not be performed depending on the
characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible with this
unit.
other manufacturers, sometimes it
may not be possible to play back
depending on the disc and recording conditions.
● It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
● It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy once programs can
only be recorded onto DVD-RW discs formatted in VR mode.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0 or 2.1.
NOTE:
The following may result if you play back a DVD-R disc recorded on
another unit.
● It is impossible to record on DVD-RAM discs which do not conform to
this standard. If you use a disc formatted under a different standard
version, format it on this unit before use.
● It may not be possible to record, play back, edit or dub a DVD-RAM
disc even if it conforms to the standard if it was recorded or edited on
the devices from other manufacturers or on a PC, or if it has far too
many titles, or if there is very little available capacity remaining on the
disc.
● The disc does not play.
● A mosaic pattern (block noise) appears on the screen.
● Video or audio may be dropped out.
● The unit stops during playback.
● DVD-RAM discs recorded on this unit cannot be played back on an
incompatible DVD player.
● It is possible to record copy-once programs of digital broadcasts only
onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs are not
compatible).
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
8
EN
Discs For Playback Only
Unplayable Discs
You can use discs with the following logos for playback only.
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
DVD VIDEO
Video CD/Super Video CD
(example of region code
indications)
● CD-ROM discs (including PHOTO-CD and CD-G)
● Discs recorded in Packet Write (UDF) format
● 1.3-GB double density CDs (DDCD)
● High density CDs (HDCD)
The following discs also cannot be played back.
● Discs of a region number other than “1”
● DVD-RAM (2.6 GB/5.2 GB)
● DVD-RAM (TYPE1)
Audio CD
CD-DA files
CD-R
CD-DA/JPEG/
MP3 files
Region Number
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is “1”. Only discs whose
region number includes “1” or “ALL” can be played back such as
shown below.
CD-RW
CD-DA/JPEG/
MP3 files
CD-ROM
JPEG/MP3 files
● Playback may not be performed depending on the characteristics
and condition of the disc used.
● DTS Audio CDs can also be played back (An optional DTS decoder
is required).
Examples of DVD VIDEO labels which can be played back
using this unit.
● MP3 and JPEG discs can be played back on this unit only when they
have been recorded in the ISO9660 or Joliet format and finalized.
● JPEG files that can be played back on this unit must conform to JFIF/
Baseline process, and the maximum resolution of a JPEG file is
2,812 x 2,112 pixels.
● CD-R/RW discs recorded in music CD format need to be finalized to
play back on this unit.
● Operation and audio quality of this unit are not guaranteed for discs
that do not conform to the Compact Disc specification (CD-DA).
Before you play back a CD, check for the CD logo and read the notes
on the package to confirm that it conforms to the Compact Disc
specification.
Marks of discs in this instruction manual
Allows operation with a
DVD-RAM disc.
Allows operation with a
Video CD/Super Video
CD (SVCD) disc.
Allows operation with a
DVD-R disc.
Allows operation with
an Audio CD disc.
● Depending on the intentions of the author of the software, recording
conditions of DVD discs and Video CD/SVCD discs may be
restricted. Since this unit plays back discs according to the intentions
of the author of the software as indicated on the disc, some functions
may not operate as commanded.
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
● When switching from the first layer to the second layer of double-
layered DVD VIDEO discs, the image and sound may be
momentarily distorted. This is not a malfunction.
● DVD-AUDIO discs compatible with DVD video players can be played.
● Super Audio CDs (SACD) compatible with conventional CD players
can be played.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
9
Audio CD/Video CD/SVCD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD/
SVCD discs.
However, some discs are not divided into tracks.
Recording Medium And Format
DVD-RAM
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
● While recording, it is possible not only to start playback of a program
currently being recorded, but also to watch another program
previously recorded.
Audio CD or Video CD/SVCD
Track 1
Track 2
Track 3
Track 4
DVD-RW (VR mode)
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organized as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (੬ pg. 69)
DVD-RW (Video mode)
File structure of a disc before starting the MP3/JPEG
Navigation
● Can be played back on other DVD players.
● New recording can be performed by erasing all the data on a disc
once played back.
DVD-R
● Can be played back on other DVD players.
● Suitable when keeping a recorded disc for a long time.
File Structure Of Discs
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
Directory
MP3 file
JPEG file
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
When you record a program on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes from monaural to stereo
due to commercial breaks, etc. It is also possible to insert chapter
marks at desired locations during playback. (੬ pg. 29)
When you record a program on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes due to commercial breaks,
etc. It is also possible to insert chapter marks at desired locations
during either recording or playback. Once the disc has been
finalized, these chapter marks are deleted and new chapter marks
are assigned automatically approximately every 5 minutes.
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
Title 1
Title 2
● This unit can recognize up to 9 hierarchies including directories and
files.
Chapter 1 Chapter 2 Chapter 3
Chapter 1 Chapter 2 Chapter 3
Also, it can recognize up to 250 files in each group, and up to 99
groups on a disc.
● In Video mode, even before finalizing, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programs and/or titles.
NOTES:
● Video CD/SVCD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and played
back according to the instructions on the screen while navigating through
the hierarchies. It is also possible to playback recorded tracks
consecutively without activating the PBC function even when playing a
PBC-compatible disc. (੬ pg. 31)
● After finalizing, it is impossible to perform editing operations.
● Regarding the contents recorded on discs
Some files may not be played back depending on the file types and other
factors.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
10
DVD VIDEO Marks
Placing A Disc
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc
may not include a mark even for a function it supports.
Opening the disc tray
Press x to open the disc tray.
Marks related to video
Number of subtitles
Number of angles
VHS/HDD/DVD
SELECT
DVD
–
DV IN
DISPLAY VHS TIMER
REC MODE
Recorded under the
standard 4:3 aspect
ratio
Screen includes black
bands at the top and
the bottom of image
which has a standard
4:3 aspect ratio (letter
box)
● Pressing the button again closes the disc tray.
● Use the button to open and close the disc tray.
● Do not block the disc tray with your hand while it is opening or closing
as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc on the
disc tray.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Video playback is in Wide video mode (16:9) on
wide televisions, but in letter box on televisions
with standard 4:3 aspect ratio.
Video playback is in Wide video mode (16:9) on
wide televisions, but pan and scan is used on
televisions with standard 4:3 aspect ratio (either
the left or right side of the image is cut-out).
Discs without cartridges
Marks related to audio
Number of audio tracks
Disc tray
Dolby Digital mark
It has been developed by Dolby Laboratories as
a digital surround system.
Place the disc on the disc tray with the label side facing up. Since
disc size changes depending on the disc to be played back, be
sure to correctly align the disc with the grooves for its size. If the
disc is not in its groove, it may be scratched or otherwise
damaged. To insert an 8 cm disc, place it according to the inner
groove.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect an
amplifier with a built-in DTS decoder to the
DIGITAL OUT connector of the unit.
DVD-RAM discs contained in cartridges
Double-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with “Side A” facing down, programs are recorded on the side A.
Single-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
11
Care And Handling Of Discs
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched and dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirt when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
12
Front View
D
A
B
C
E
F G H I J
VHS/HDD/DVD
STANDBY/ ON
S-VIDEO
SELECT
VHS
–
HDD
–
DVD
–
VIDEO (MONO)L–AUDIO–R
DV IN
CH
DISPLAY VHS TIMER
REC MODE
HDD/DVD
F–1
HDD/DVD
KL
M
O
P Q R S T V W X
U
A Eject Button (x) (VHS) ੬ pg. 50
B Cassette Loading Slot
੬ pg. 75
M Video/Audio Input Connectors
VHS Recording Lamp (7) ੬ pg. 53
D HDD Lamp (HDD) ੬ pg. 21, 44
E Open/Close Button (x) ੬ pg. 10
F VHS/HDD/DVD Select Button (VHS/HDD/DVD
N Channel Buttons (CH +/–) ੬ pg. 41, 44, 52, 53
O Front Display Panel ੬ pg. 14
R Display Button (DISPLAY) ੬ pg. 30, 42
T Recording Mode Button (REC MODE) ੬ pg. 41, 44, 53
mode.
H Disc Tray
I Reverse Search Button (3) (HDD &DVD deck)
੬ pg. 28, 35
Rewind Button (3) (VHS deck) ੬ pg. 50, 51
J Forward Search Button (5) (HDD &DVD deck)
੬ pg. 28, 35
V Record Button (7) ੬ pg. 41, 44
W Pause Button (9) ੬ pg. 27, 46
X DV Input connector [DV IN (i*)] (HDD & DVD deck only)
੬ pg. 74
*
i (i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof. The i logo is used for products compliant with the
i.Link standard.
Fast Forward Button (5) (VHS deck) ੬ pg. 50, 51
K STANDBY/ON Button (1)
To access covered connectors, pull
and open the connector cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
13
Rear View
G
H
A B
C
D E F
HDD/DVD
S-VIDEO
HDD/DVD
S-VIDEO
DIGITAL
COMPONENT
PCM/
AUDIO OUT VIDEO OUT
STREAM
HDD/DVD
VHS
VIDEO
Y
OPTICAL
IN
VIDEO
VIDEO
PB
VHS/HDD
/DVD
L
AUDIO
R
L
AUDIO
R
L
COAXIAL
CABLE
BOX
AUDIO
R
PR
OUT
ANT. LOOP OUT
VHF/UHF
TV OUT
OUTPUT INPUT L-1
HDD/DVD
OUTPUT
I
J K
A Region Number Label ੬ pg. 8
B AC Power Cord ੬ pg. 19
E Component Video Output Connectors [COMPONENT
● This component video output enables you to watch the images
Progressive Scan” (੬ pg. 52).
Do not remove it.
F S-video/Video/Audio Output Connectors [S-VIDEO/
● Install the unit so as not to block the area around the fan.
● The cooling fan on the rear of the unit may be activated even if
the unit is turned off in the following cases;
੬ pg. 19
DVD deck only) ੬ pg. 76
H Antenna Input Connectors [VHF/UHF IN] ੬ pg. 19
I Video/Audio Input Connectors [VIDEO/AUDIO INPUT
L1] ੬ pg. 76
J Video/Audio Output Connectors [VIDEO/AUDIO
OUTPUT] ੬ pg. 76
(੬ pg. 59)
— when “AUTO CLOCK” is set to “ON” (੬ pg. 22)
(Set “AUTO CLOCK” to “OFF” if you mind the noise of the fan.)
D Digital Audio Output Connectors
[DIGITAL AUDIO OUT (OPTICAL/COAXIAL)] (HDD &
DVD deck only) ੬ pg. 77, 80
K Cable Box Control Connector [CABLE BOX] ੬ pg. 24
L Antenna Output Connectors [VHF/UHF OUT] ੬ pg. 19
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
14
Front Display Panel
K
L
A
B
C DEF
G
H I
J
LPCM
FR
XP SP LP EP
VR +
-
RW VCD
VHS HDD DVD
-
M
N O
P
Q
R
S
T
A Video Indicator (
) ੬ pg. 42, 45, 53
H Channel/Recording Mode Indicator
Indicates the channel received. Or the recording mode (SP, EP) of
the VHS deck.
Lights when VIDEO mode is selected by pressing TV/VIDEO. Lights
off when TV mode is selected.
B Disc Type Indicator
I Track/Chapter Indicator (TRK/CHAP)
“TRK” or “CHAP” lights depending on a disc loaded while the 3rd
and 4th digits from the left of the Multi Display (Q) indicate the
numbers explained below.
When a disc is loaded, the type of the disc is indicated.
Disc Status Indicator
When a disc is running, the disc marks rotate.
During High-Speed Search: Rotate faster than normal playback.
During Slow Motion:
While recording:
“TRK”:
Total number of tracks or track number being played
back are displayed on the Multi Display.
Rotate slower than normal playback.
Inner red ring lights in the same way
as normal playback. During Instant
Timer Recording (ITR), inner red ring
slowly blinks.
recording or playing back.
Disc marks all light.
Multi Display.
J Simulated Surround Effect Indicator (3D) ੬ pg. 38
Lights when a simulated surround effect is set to “3D-ON” on the
on-screen bar.
While paused:
K Random/Program Playback Mode Indicator (RND/
PRGM) ੬ pg. 39
While stopped:
While resume stopped:
No disc on the disc tray:
Disc marks all blink.
Disc marks all light out.
Disc marks all light out.
“RND”:
Lights when Random Playback mode is set.
“PRGM”: Lights when Program Playback mode is set.
Select Repeat Playback mode on the on-screen bar.
VR Mode Indicator (VR) ੬ pg. 87
Lights when a DVD-RW disc is formatted in VR mode.
C Linear PCM Indicator (LPCM)
“
“
“
”:
1”:
Whole disc is played back repeatedly.
A–B”: The selected part (A–B) is played back repeatedly.
Lights when “XP MODE REC AUDIO” is set to “LINEAR PCM”
(੬ pg. 82) for recording with HDD, DVD-RAM, DVD-R and
DVD-RW discs, and when Linear PCM audio is played.
No display: Repeat Playback mode is off.
M VHS Indicator ੬ pg. 42
D Cassette Loaded Mark (
)
Lights when VHS mode has been selected, during recording or
when tapes recorded in VHS format are played back.
No display: Indicates that interlace mode is engaged.
Indicates the present of a cassette in the VHS deck.
Lights when a cassette is loaded into the VHS deck. Blinks when
the end of the tape has been reached during timer recording, or
when the unit is in timer recording standby mode with a cassette
without record safety tab inserted.
:
Indicates that progressive mode is engaged.
lights when video output mode is in progressive
(Example)
mode.
E VHS Timer Indicator (
)
Lights when the VHS deck is in the timer recording standby mode or
when timer recording is in progress.
O Automatic Satellite Program Recording Indicator
੬ pg. 59
Blinks rapidly when VHS TIMER is pressed under the following
conditions:
● Clock is not set.
● Timer programming has not been set.
● Cassette is not loaded.
● Timer recording standby mode with a cassette without safety tab
inserted.
Lights when the HDD deck is in the Auto Satellite Program
Recording standby mode.
P Group/Title Number Display
Q Track/Chapter Number Display
R Remaining Time/Elapsed Time Indicator ੬ pg. 30, 42
Lights when remaining time of HDD, DVD-RAM, DVD-R and
DVD-RW discs is displayed, and lights out when elapsed time is
displayed.
The right 6 digits of the Multi Display (S) indicate elapsed or
remaining time of each track.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
S Remaining Time/Elapsed Time Display ੬ pg. 30, 42
● Tape end is reached during time recording.
F Recording Mode Indicator (XP/SP/LP/EP/FR) ੬ pg. 41
Blinks when recording mode is being set.
While “FR” is blinking, the left 3 digits of the Multi Display (P Q)
indicate setting values ranging from “60” to “480”. After the value
has been set, only “FR” lights.
G Group/Title Indicator (GRP/TITLE)
“GRP” or “TITLE” lights depending on a disc loaded while the left 2
digits of the Multi Display (P) indicate the numbers explained
below.
T Multi Display
Displays clock, received channel, elapsed time, and remaining time.
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
“GRP”:
Total number of groups or group number being played
back are displayed on the Multi Display.
“TITLE”: Total number of titles or title number being played back
are displayed on the Multi Display.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
15
P Jump Button (JUMP +/–) ੬ pg. 49
Remote Control
Q Recording Mode Button (REC MODE) ੬ pg. 41, 44
Remain Button (REMAIN) ੬ pg. 30, 42
T Subtitle Button (SUBTITLE) ੬ pg. 30
U TV/CABLE/DBS/DVD switch ੬ pg. 21
CABLE/DBS
TV DVD
U
V
STANDBY/ON
A
TV/
VHS
TIMER
DVD
TV/CBL/DBS
VIDEO
B
C
D
W
X
VHS
HDD
DVD
੬ pg. 78
TV VOLUME
X DVD Button* ੬ pg. 27
Y
E
CH
a Memo Button (MEMO) ੬ pg. 64, 67
Mark Button (MARK) ੬ pg. 29
c Edit Button (EDIT) ੬ pg. 64
Z
a
CANCEL
LIVE
AUX
MEMO/MARK
EDIT
F
G
H
I
J
K
DUBBING
PROGRAM
e Enter Button (ENTER) ੬ pg. 21
Next Button (NEXT) ੬ pg. 31
੬ pg. 28, 48
i Play Button (4) ੬ pg. 27, 46
b
c
d
TV MUTING
TOP MENU
MENU
NAVIGATION
RETURN
ENTER
e
f
g
L
PREVIOUS
SLOW
NEXT
SLOW
M
N
O
P
PLAY/SELECT
h
Select Button (SELECT) ੬ pg. 69
j Pause Button (9) ੬ pg. 27, 46
k Stop Button (8) ੬ pg. 27, 46
i
j
k
l
m
n
CLEAR
STOP/
REC
PAUSE
JUMP
l Skip Search Button (
) ੬ pg. 29, 48
REC MODE
REMAIN
DISPLAY
ON SCREEN
SET UP
n One Touch Replay Button (
) ੬ pg. 48
Q
R
p Automatic Satellite Program Recording Button (REC
LINK) ੬ pg. 59
q Progressive Scan Button (PROGRESSIVE SCAN)
੬ pg. 83
r Angle Button (ANGLE) (DVD deck only) ੬ pg. 30
Live Check Button (LIVE CHECK) ੬ pg. 35, 48
o
REC LINK
p
PROGRESSIVE
AUDIO
SUBTITLE
S
T
r
How To Use
Before use, insert two AA size batteries into the remote control
with the polarity ( and ) matched correctly as indicated on
the battery compartment or on the lid.
C VHS Button* ੬ pg. 50
The remote control can operate most of your unit’s functions, as
well as basic functions of TV sets of JVC and other brands.
(੬ pg. 78)
● Point the remote control toward the receiving window.
● The maximum operating distance of the remote control is about
8 m.
D HDD Button* ੬ pg. 44
E Number Keys ੬ pg. 23, 41, 44
NOTE:
G Auxiliary Button (AUX)
H Live Button (LIVE) ੬ pg. 35, 48
I Dubbing Button (DUBBING) ੬ pg. 70
TV Muting Button (TV MUTING) ੬ pg. 78
K rt w e Buttons ੬ pg. 21
If the remote control doesn’t work properly, remove its batteries, wait
a short time, replace the batteries and then try again.
L Menu Button (MENU) ੬ pg. 28
Previous Button (PREVIOUS) ੬ pg. 31
N Reverse Search Button (3) (HDD & DVD deck)
੬ pg. 28, 48
Rewind Button (3) (VHS deck) ੬ pg. 50
Reverse Slow Button (SLOW –) ੬ pg. 29
O Record Button (7) ੬ pg. 41, 44
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
16
When pressing REC MODE
(Appears for eight seconds.)
On-Screen Display (DVD deck)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN twice.
RAM
FR360
7: 00
XP
SP
LP
EP
FR480
10: 00
20: 00
28: 00
36: 00
When playing back a recorded title
A Disc type
B Current recording speed
C Remaining disc time for each recording speed
D Recording speed
TITLE99 CHAPTER999 T. REMAIN6:59:59
01:16:48
12
XP
FISHING WORLD
A Playback title number
B Playback chapter number
C Disc remaining time
D Current status (playback)
E Audio mode
F Current received (recording) channel position number
(On playback background)
When pressing 7 during recording
ITR
2 : 30
A Recording time for Instant Timer Recording (ITR) mode
G Bar meter
H Name of title (or play list) currently being played back
I Current playback point
J Recorded mode
K Live Memory mode (recording)
When recording
TITLE99 CHAPTER999 T. REMAIN6:59:59
11:35 AM
RAM
12
FR360
A Recording point
B Current status (recording)
C Current time
D Recording channel number
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
17
When recording
On-Screen Display (HDD deck)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN twice.
11:00
FR360
12:00
1:00
11:35AM
11:33AM
12
STEREO
A Live Memory Recording point
B Live Memory Recording mode
When playing back a recorded title
When pressing REC MODE
(Appears for eight seconds.)
0:00
1:00
2:00
01:16:48
STEREO
12
004 FISHING WORLD
FR360
FR360
A Title start
B Current playback point
C Title end
D Time scale (This title is an hour and a half long.)
E Play mode
7: 00
10: 00
20: 00
28: 00
36: 00
XP
SP
LP
EP
FR480
F Elapsed playing time
G Current received (recording) channel position number
(On playback background)
H Recorded title (or play list) number currently being played back
I Name of title currently being played back
J Audio mode
A HDD capacity graph
B Current recording speed
C Remaining HDD time for each recording speed
D Recording speed
When pressing 7 during recording
K Live Memory mode (recording)
When watching a program on air
ITR
2 : 30
A Recording time for Instant Timer Recording (ITR) mode
11:00
12:00
1:00
11:35AM
12
STEREO
ON AIR
A Possible start point from where Live Memory Playback can be
performed
B Possible start point from where Live Memory Recording can be
performed
(Received channel has changed at this point.)
C Currently viewed point
D Time scale
E Current time
F Current received channel position number
When using Live Memory playback
11:00
12:00
1:00
11:35AM
11:35AM
12
STEREO
A Time scale for Temporary Recording
B Current Temporary Recording point
C Current time
D Current playback channel position number
E Time scale for Live Memory Playback
F Current playback point
G Live Memory playback mode
H Current playback time
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
18
On-Screen Display (DV Dubbing)
On-Screen Display (VHS deck)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN again.
When capturing images from the external DV
equipment
0:00
FR360 00:00:00. 00
12bit
1:00
2:00
DV
HDD
GR-DV3500
L - R
00:00:00. 00
L
DV
JVC
GR-DV3500
SOUND1
K
A
J
B
I
A Recording speed
B HDD capacity graph
C HDD time counter
D Recording time scale
E HDD mode
H
C
D
F Remote control mode
E
F
G Connected DV equipment mode
H Connected DV equipment model information
I Input channel
G
J Sound mode
K Sound input bit-rate*
A Operation Mode Indicators
* Indicates the sound bit-rate of the connected DV equipment
L Connected DV equipment information*
C Tape Position Indicator
* Maker name and model name, etc. may not appear depending on the
connected equipment.
The tape position indicator
appears on the TV screen when
you press 3 or 5 from the
Stop mode or perform an Index
Search. (੬ pg. 51) The position
of “ ” in relation to “0”
M Time counter for the connected DV equipment
N Sound monitor mode
1
2
DV
DV
(Beginning) or “+” (End) shows
you where you are on the tape.
NOTE:
O Remote control switch
P Auto capture button
Q Sound monitor switch
End
Depending on the type of tape
being used, the tape position
Beginning
indicator may not appear correctly.
D Index number ੬ pg. 51
E Tape Remaining Time Indicator ੬ pg. 54
F Counter Display
179 :59 :59
G Audio Mode Display ੬ pg. 52
H SAP Indicator ੬ pg. 54
I Stereo Program Indicator ੬ pg. 54
J Day/Clock Display
R Elapsed recording time
K Channel Position Number/Auxiliary Input Indicator (L-1
or F-1)
L “Cassette Loaded” Mark
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
19
● Connect the unit’s [ANT. LOOP OUT] connector to the antenna input
connector on another video unit.
8 AV Connection
To connect to a TV with AV input connectors —
A Perform A – B in “RF Connection”.
VIDEO OUTPUT] connectors on the rear panel of the unit and
the TV’s audio/video input connectors.
Basic Connections
Antenna or Cable
Coaxial cable
8 S-Video Connection (HDD & DVD deck only)
To connect to TV’s S-VIDEO input and AUDIO input
connectors —
Flat feeder
A Perform A – B in “RF Connection”.
Matching transformer
(not supplied)
B Connect the unit’s [S-VIDEO OUTPUT] connector to the TV’s
S-VIDEO input connector.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
● If your TV is not stereo-capable, use the unit’s [AUDIO OUTPUT]
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
RF cable ( not supplied)
Antenna splitter
(not supplied)
RF cable
(not
RF cable (not supplied)
AC outlet
supplied)
8 Component Video Connection
To connect to TV’s component video input connectors —
A Perform A – B in “RF Connection”.
B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
connectors to the TV’s component video input connectors.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
To [VHF/
UHF IN]
(VHS)
AC power cord
To [VHF/UHF IN]
(HDD/DVD)
● You can obtain high-quality component video pictures.
● If your TV is not stereo-capable, use the unit’s [AUDIO OUTPUT]
reproduction.
● By using the component video connection, you can view the images
to “Scan Mode Set” (੬ pg. 83).
.
Back of unit
To
[COMPONENT
VIDEO OUT
(Y/PB/PR)]
To [S-VIDEO
OUTPUT]
To [TV
OUT]
To [AUDIO/
VIDEO
OUTPUT]
● You can also watch the images on the VHS deck in Progressive scan
mode via the component video output, refer to “VHS Progressive
Scan” (੬ pg. 52).
Audio/video
cable
S-Video cable
(not supplied
)
(
supplied)
Component
video cable
(not supplied
4 Plug the end of the AC power cord into an AC outlet. This unit
performs Plug & Play Set automatically. (੬ pg. 20)
RF cable
(supplied)
)
● The clock and tuner channels will automatically be set when the
antenna is connected and when the AC power cord is first connected
to an AC outlet. (If “AUTO” and the channel indicator are displayed
on the front display panel before the unit is powered on, the clock and
tuner channels are being set automatically. Wait for the time to be
displayed on the front display panel before turning on the unit.)
● “LOADING” blinks on the front display panel when the AC plug of the
AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
To S-VIDEO
input connector
To audio/
video input
connectors
TV
To 75 ohm
terminal
To component video
input connectors
5 Set the video channel. The video channel is the channel on
which you can watch the picture from the unit on the TV when only
using RF connection.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
With RF Connection
Set the video channel to “3 CH” or “4 CH”. To set the video
channel, perform steps A – C below:
● The video channel is preset to “3 CH”. Set to “4 CH” if the Channel 3
is used for broadcasting in your area.
1 Make sure the package contains all of the accessories listed in
“SPECIFICATIONS” on page 93.
2 Place the unit on a stable, horizontal surface.
With AV Connection
Set the video channel to “– CH” (off). To set the video channel,
perform steps A – C below:
3 Connect the unit to a TV depending on the TV and cables you
use.
8 RF Connection
To connect to a TV with NO AV input connectors —
A Disconnect the TV antenna from the TV.
B Connect the TV antenna cable to the [VHF/UHF IN] connectors
on the rear panel of the unit via antenna splitter.
C Connect the supplied RF cable between the [TV OUT]
connector on the rear panel of the unit and the TV’s antenna
terminal.
With S-Video/Component Video Connection (HDD & DVD deck
only)
Set the video channel to “– CH” (off). To set the video channel,
perform steps A – C below:
How To Set The Video Channel
A Make sure that there is no cassette in the unit.
B Press 1 to turn off the unit, then press 8 on the unit for more
than 5 seconds. “3 CH” appears on the front display panel.
C Press CH +/– on the remote control to select “3 CH”, “4 CH” or
“– CH” (off), then press ENTER.
NOTES:
● If you do not use antenna splitter, connect the TV antenna cable to
[VHF/UHF IN] (HDD/DVD) connector. However, it is not possible to
record the TV program on the VCR deck.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
20
1 Connect the antenna cable to the unit. (੬ pg. 19) Then connect
the AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels will be set automatically.
● “LOADING” blinks on the front display panel when the AC plug of the
AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
Plug & Play Set
Auto Clock Set/Auto Tuner Set
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date can be set automatically by the clock setting
We call this TV channel the “host channel” and it is a PBS channel
in your area.
NOTES:
● Auto Clock Set is performed first.
channels that are receivable by your unit. During Auto Channel Set,
the channel numbers are displayed as they are scanned and set.
● When Plug & Play setting has been completed successfully, the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform “Clock Set” (੬ pg. 22) and
“Tuner Set” (੬ pg. 23). If, however, you want to add or delete
channels, refer to “Manual Channel Set” (੬ pg. 23).
ATTENTION:
● If you use a cable box, Plug&Play will not function; set the clock
and tuner channels separately. (੬ pg. 22 – 23)
● Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If this
function is taking a considerable amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
During Auto Clock Set
“AUTO” blinks.
VHS/HDD/DVD
STANDBY/ ON
SELECT
VRS
–
HDD
–
DVD
–
SO
HDD/DV
VIDEO (MONO)L–AUDIO–R
DV IN
CH
DISPLAY VHS TIMER
REC MODE
F–1
During Auto Channel Set
The channel numbers are displayed and “AUTO” blinks as they
are scanned and set.
INFORMATION
adjusted automatically by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
PBS channel clock setting data. (This automatic clock adjustment
can only be performed when the unit is turned off. The clock will be
adjusted just on these hours — on the time displayed on the front
display panel, not on the actual real time.) The default setting of
“AUTO CLOCK” is “ON”. (੬ pg. 22)
Plug&Play Completed
The current time is displayed.
● If an incorrect clock time or “– –:– –” appears on the front display
panel, see “What to do if Plug & Play setting failed” (੬ pg. 20).
● If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you may
be receiving the clock setting data of a PBS channel from an
adjacent time zone, or an incorrect PBS channel from a cable TV
system. In this case, perform “Semiauto Clock Set” (੬ pg. 22) or
may not be connected to the unit or there may not be a Host PBS
signal available in your area. Ensure that the antenna cable is
connected correctly. Then turn on and off the unit; the Plug & Play
setting will be automatically reactivated. If Plug & Play setting is
not performed though the antenna cable is connected correctly,
perform “Manual Clock Set” (੬ pg. 22) and “Auto Channel Set”
(੬ pg. 23) or “Manual Channel Set” (੬ pg. 23).
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
21
On-screen Language Set
This unit offers you the choice to view on-screen messages in 3
different languages.
Language
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “FUNCTION SET UP”, then press t.
4 Press w e to select “DISPLAY
CABLE/DBS
TV
DVD
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
SET”, then press t.
REC/PLAY SET UP
DISPLAY SET
VIDEO IN/OUT
HDD
DVD
SUPERIMPOSE
BLUE BACK
DIMMER
AUTO
5 Press rt to select “ON
SCREEN LANGUAGE”, then
press ENTER.
ON
BRIGHT
OFF
POWER SAVE
ON SCREEN LANGUAGE
ENGLISH
6 Press rt to select your
desired language, then press
ENTER.
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
7 Press SET UP to complete the setting.
ENTER
rtwe
Menu/Audio/Subtitle Language Set (DVD deck only)
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
● The procedure shows how to set “MENU LANGUAGE” as an
example.
SET UP
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “DVD VIDEO SET UP”, then press t.
4 Press w e to select
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
DISC SET UP
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LOCK
“LANGUAGE SET”, then press
ENTER.
ENGLISH
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
LANGUAGE”, then press ENTER.
6 Press rt to select your
desired language, then press
ENTER.
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
● See “Language Code List”
(੬ pg. 94).
7 Press SET UP to complete the setting.
NOTE:
When the selected language is not available on the disc, the disc’s
default menu language is played back.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
22
NOTE:
Clock Set
If an incorrect time is displayed by the Plug & Play function, you may be
receiving the clock setting data of a PBS channel from an adjacent time
zone or from an incorrect PBS channel from a cable TV system. If you
selected “AUTO” for the host channel in step 6, be sure to select the
correct time zone manually.
Perform clock setting only if the clock has not been set correctly by
the Plug&Play setting.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
9 Press SET UP to complete the setting.
IMPORTANT:
Turn off the unit after performing Semiauto Clock. “AUTO” will
appear on the front display panel while the clock is being set. The
current clock time will appear automatically when the clock setting is
complete.
CABLE/DBS
TV
DVD
HDD
DVD
Auto Daylight Saving Time
This function enables automatic adjustment of the unit’s clock at
the start and end of Daylight Saving Time.
With Auto DST activated, —
— on the first Sunday of April at 2:00 AM, the clock is adjusted
to 3:00 AM.
— on the last Sunday of October at 2:00 AM, the clock is
adjusted to 1:00 AM.
ENTER
rtwe
NOTE:
Timer recording may not function correctly at the time Daylight
Saving Time is adjusted.
Manual Clock Set
SET UP
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “CLOCK
CLOCK SET
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
SET”, then press t.
TUNER SET
STB SET
Semiauto Clock Set
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually.
AUTO CLOCK
HOST CH
ON
AUTO
AUTO
AUTO
D. S. T.
TIME ZONE
NOTE:
SET UP
EXIT
ENTER
SELECT
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
The time set previously will be erased when “AUTO CLOCK”, “HOST
CH”, “D.S.T.” or “TIME ZONE” setting is changed.
5 Press rt to select “AUTO
CLOCK”, then press ENTER.
Press rt to select “OFF”, then
press ENTER.
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
TUNER SET
STB SET
CLOCK SET
the unit.
AUTO CLOCK
TIME
OFF
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “CLOCK
CLOCK SET
- - : - -
1/1(THU)
2004
DATE
6 Press rt to select “TIME”,
then press ENTER. Press rt
until the desired time appears,
then press ENTER to start clock.
● Set the date and year in the same
way.
YEAR
D. S. T.
ON
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
SET UP
EXIT
ENTER
SELECT
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SET”, then press t.
TUNER SET
STB SET
AUTO CLOCK
HOST CH
ON
5 Press rt to select “AUTO
CLOCK [CATV]”, then press
ENTER. Press rt to select “ON”,
then press ENTER.
AUTO
AUTO
AUTO
D. S. T.
TIME ZONE
● Holding rt changes the time in 30-minutes interval, or changes the
date in 15-days interval.
SET UP
EXIT
ENTER
SELECT
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
6 Press rt to select “HOST
7 Press rt to select “D.S.T.”, then press ENTER. Press rt to
CH”, then press ENTER.
select the desired setting, then press ENTER.
Press rt to select “AUTO” or the
ON: Adjustment will be made by the built-in clock itself.
OFF: Select when Daylight Saving Time does not apply to you.
8 Press SET UP to complete the setting.
desired PBS channel number, then press ENTER.
NOTE:
Some PBS channels do not transmit clock setting data.
7 Press rt to select “D.S.T.”, then press ENTER. Press rt to
select the desired setting, then press ENTER.
AUTO: Select if you want to adjust your unit’s clock automatically
by the incoming signal from the host channel. Be sure to select
the correct time zone manually in step 8.
ON: Adjustment will be made by the built-in clock itself.
OFF: Select when Daylight Saving Time does not apply to you.
8 Press rt to select “TIME ZONE”, then press ENTER. Press
rt to select “AUTO” or the desired time zone, then press ENTER.
● Each time you press rt, the time zone changes as follows:
{AUTO{ATLANTIC{EASTERN{CENTRAL{
MOUNTAIN{PACIFIC{ALASKA{HAWAII{
(back to the beginning)
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
23
Manual Channel Set
You can add the channels you want or delete the channels you do
not want manually.
Tuner Set
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press ENTER.
4 Press w e to select “TUNER SET”, then press t.
CABLE/DBS
TV
DVD
HDD
0-9
5 Press rt w e to select “MANUAL CH SET”, then press
DVD
ENTER.
6 Add or skip the desired channels.
INITIAL SET UP > MANUAL CH SET
To add channels
BAND
CH
CATV
1
A Press rt to select “CH”, then
press ENTER.
ADD/SKIP
ADD
B Press the number keys to enter
a channel number you want to
add, then press ENTER.
C Press rt to select “ADD/SKIP”,
then press ENTER.
RETURN
ENTER
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
rtwe
SELECT
D Press rt to select “ADD”, then press ENTER.
E Repeat B – D to add other channels.
To skip channels
A Press rt to select “CH”, then press ENTER.
B Press rt to select a channel number you want to skip, then
press ENTER.
SET UP
C Press rt to select “ADD/SKIP”, then press ENTER.
D Press rt to select “SKIP”, then press ENTER.
E Repeat B – D to skip other channels.
7 Press SET UP to complete the setting.
INFORMATION
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be displayed on
the right side of “BAND” on the Tuner Set screen.
Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “TUNER
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
TUNER SET
STB SET
CLOCK SET
SET”, then press t.
AUTO CH SET
MANUAL CH SET
GUIDE CH SET
11
12
13
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
5 Press rt w e to select
“AUTO CH SET”, then press
ENTER. You can automatically
set the receivable channels in
your area in the order of their
frequencies.
INITIAL SET UP > AUTO CH SET
AUTO CHANNEL SET SCANNING
CANCEL
● When Auto Channel Set is
complete, “SCAN COMPLETED”
appears on the TV screen.
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
● If the scan was unsuccessful, “SCAN COMPLETED–NO SIGNAL–”
appears on screen. Check the connections and start again.
6 Press SET UP to complete the setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
24
If your cable box or DBS receiver does not have audio/video
output connectors
Connect the RF output connector on the cable box or DBS receiver to the
[VHF/UHF IN] (HDD/DVD) connector on the rear of your unit.
Cable Box and/or DBS Receiver Control
Setting (HDD & DVD Deck only)
If your cable box or DBS receiver has audio/video output
Connect the audio/video output connectors on the cable box or
DBS receiver to the [AUDIO/VIDEO INPUT] connectors on the rear
of the unit.
● If both a cable box and a DBS receiver are used, it is recommended
that you connect the DBS receiver to your unit’s [AUDIO/VIDEO
INPUT] connectors and the cable box to your unit’s [VHF/UHF IN]
(HDD/DVD) connector.
The following procedure is required if you receive your TV
satellite channels through DBS (Direct Broadcast Satellite)
receiver. The Controller allows the unit to automatically switch the
cable box and/or DBS receiver’s channels during timer recording.
NOTES:
3
● The Controller is effective for “VCR Plus+ C ® Timer Programming”
(੬ pg. 55), or “Manual Timer Programming” (੬ pg. 57).
● When connecting your cable box, refer to its instruction manual.
4 Connect the Controller to the [CABLE BOX] connector on the
rear panel.
Installing Controller
1 If both a cable box and a DBS receiver are used, position the
Controller so its signal reaches the receiving windows of both the
cable box and DBS receiver.
Setting Brand And Channel
After installation, set the cable box and/or DBS receiver’s brand and
channels correctly; otherwise, the Controller cannot work correctly.
2 Fix securely using the adhesive strip attached on the back of the
● Turn on the unit.
Controller.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Cable box or DBS
receiver
CABLE/DBS
TV
DVD
HDD
DVD
Your unit
Controller
(suggested locations)
ENTER
rtwe
3 Connect the controller to the unit.
a
Cable box or DBS receiver
SET UP
To RF output
To Audio/video
output
Transmitter
Controller
or
1 Turn on the cable box and/or DBS receiver.
To [VHF/UHF IN]
(HDD/DVD)
To [AUDIO/
VIDEO INPUT]
2 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
3 Press SET UP to access the Main Menu screen.
4 Press w e to select “INITIAL SET UP”, then press t.
5 Press w e to select “STB SET”, then press t.
6 Press rt to select “CABLE
Your unit
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
SET UP” or “DBS SET UP”, then
TUNER SET
STB SET
CLOCK SET
CABLE
BOX
press ENTER.
CABLE SET UP
DBS SET UP
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
7 Press rt to select “CABLE
BOX OUTPUT CHANNEL” or “DBS
RECEIVER OUTPUT CHANNEL”,
then press ENTER.
INITIAL SET UP > CABLE SET UP
CABLE BOX OUTPUT CHANNEL
BRAND
OFF
1
RETURN
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
25
8 Select the output channel.
8 For cable box
Your selection depends on how the cable box and/or DBS receiver
is connected to your unit.
If the cable box’s channel changes to 9, setting is complete.
Press ENTER and “CABLE BOX
INITIAL SET UP > CABLE SET UP
● If the cable box or DBS receiver is connected to your unit’s
[VHF/UHF IN] (HDD/DVD) connector on the rear panel, press rt
to select the channel number representing the cable box’s output
(CH2 – CH9), then press ENTER.
● If the cable box or DBS receiver is connected to your unit’s
[VIDEO/AUDIO ((MONO) L/R)] input connectors on the front
panel, press rt to select “F-1”, then press ENTER.
● If the cable box or DBS receiver is connected to your unit’s
[AUDIO/VIDEO INPUT] connectors on the rear panel, press rt
to select “L-1”, then press ENTER.
CONTROL IS ON” appears on the
the screen in step 6 appears.
DID YOUR CABLE BOX CHANGE TO CHANNEL 09?
If the cable box’s channel does
not change to 9;
A Press w e to select “NO”, then
press ENTER.
B Repeat steps 9 – 10 until the cable box’s channel changes to 9
by entering another code.
YES
N O
SET UP
EXIT
ENTER
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
SELECT
C If the channel does not change after going through all the code
numbers listed for your model of cable box, then try all the other
numbers.
● If you do not use a cable box or DBS receiver, press rt to select
“OFF”, then press ENTER.
9 Press rt to select “BRAND”, then press ENTER. Press rt to
8 For DBS receiver
select the brand code from the following list, then press ENTER.
If the DBS receiver’s channel
INITIAL SET UP > DBS SET UP
10Press rt to select “RETURN”, then press ENTER.
changes to the channel listed
CABLE BOX BRAND
CODE
complete.
Press ENTER and “DBS
DID YOUR DBS BOX CHANGE TO CHANNEL 100?
ARCHER
1, 5, 17
1, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
2, 8
YES
N O
RECEIVER CONTROL IS ON”
appears on the screen for about 5
seconds, then press ENTER. The
screen in step 6 appears.
CABLETENNA
CABLEVIEW
CITIZEN
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
CURTIS
JVC
ECHOSTAR
]
]
100
100
SONY
RCA
]
]
205
205
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
1, 17
15, 16, 17, 21, 25
15
1, 4, 6, 11, 12, 15, 28
10, 18, 23
15
If the DBS receiver’s channel does not change as shown
above;
A Press w e to select “NO”, then press ENTER.
B Repeat steps 9 – 10.
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
1, 4, 6, 11, 12, 15, 28
2, 8
7, 20
13, 14
15, 16, 17, 21, 25
13, 14
NOTES:
● The Controller may not work with all types of cable box or DBS
receiver.
● If your cable box does not respond to any code between 1 and 28,
you cannot use the Controller to change cable box channels. In this
case, make sure to leave the cable box turned on and tuned to the
proper channel before the scheduled start time of timer recording.
Contact your cable company about the possibility of exchanging your
current cable box with the one compatible with your unit.
● If your DBS receiver does not respond to the code, you cannot use
the Controller to change satellite channels. In this case, make sure to
leave the DBS receiver turned on and tuned to the proper channel
before the scheduled start time of timer recording.
● The unit can only change the cable box or satellite channel through
the Controller during timer recording.
● If your cable box and/or DBS receiver cannot be operated with a
remote control (because it has no receiving window), you cannot use
the Controller to change its channels. Make sure to leave the cable
box and/or DBS receiver turned on and tuned to the proper channel
before the scheduled start time of timer recording.
RCA
REGAL
10, 18, 23
1, 16, 17
5, 16, 24
2, 8
7, 20
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
5, 16, 17, 24, 25
13, 14
5, 15, 16, 17, 21, 24, 25
5, 16, 24
SPRUCER
STARGATE
TELEVIEW
TOCOM
1, 4, 16
UNIKA
1, 17
16, 17, 25
3, 9, 22
UNIVERSAL
VIDEOWAY
ZENITH
3, 9, 22
● If the unit’s memory backup expires because of a power failure, set
the cable box and/or DBS receiver output channels and brands
again.
● For customers in U.S.A.: If you are unable to set the Controller,
contact JVC toll free at 1-800-252-5722.
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
51
51
41
40
RCA (DSS)
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
26
1 Press DVD so that the DVD lamp lights up on the unit.
Monitor Set
2 Press SET UP to access the Main Menu screen.
● You cannot set the monitor type during recording or playback.
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
3 Press w e to select “FUNCTION SET UP”, then press t.
4 Press w e to select “VIDEO IN/
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
OUT”, then press t.
REC/PLAY SET UP
DISPLAY SET
VIDEO IN/OUT
MONITOR TYPE
F-1 INPUT
4:3LB
VEDIO
VEDIO
5 Press rt to select “MONITOR
TYPE”, then press ENTER.
L-1 INPUT
6 Press rt to select the desired
option, then press ENTER.
CABLE/DBS
TV
DVD
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
7 Press SET UP to complete the
SELECT
setting.
DVD
* The boldface settings below indicate the settings at your
purchase.
8 MONITOR TYPE — 4:3LB / 4:3PS / 16:9 AUTO / 16:9 FIX
4:3LB (Letter Box conversion): Select this when the aspect ratio of
your TV is 4:3 (conventional TV). While viewing a wide screen
picture, the black bars appear on the top and the bottom of the
screen.
ENTER
rtwe
4:3PS (Pan&Scan): Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide screen picture, the
black bars do not appear; however, the left and right edges of the
pictures will not be shown on the screen.
16:9 AUTO (Wide television conversion): Select this when the
aspect ratio of your TV is 16:9 (wide TV).
SET UP
16:9 FIX (Wide television conversion): Select this when the aspect
ratio of your TV is fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal correctly when
playing back a picture whose aspect ratio is 4:3.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.
There are two styles to display the image, “Pan&Scan” (PS) and
“Letter Box” (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
● The picture will be shown in the “4:3LB” mode
depending on the disc even if the “4:3PS” mode
is selected.
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
27
To play back an MP3/JPEG disc, see “Playback With MP3/WMA/
JPEG Navigation” (੬ pg. 69).
Basic Playback
1 Load a disc.
● For details, refer to “Placing A Disc” (੬ pg. 10).
● Pressing 4 also closes the disc tray.
● Playback begins automatically if an auto-playback DVD disc is
loaded.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD
on the remote so that the DVD lamp lights up on the unit.
3 Press 4 to start playback.
● If you load a DVD disc whose region code does not match the unit,
“REGION CODE ERROR” appears on the TV screen. For details,
VHS/HDD/DVD
x
SELECT
4
appears on the TV screen, refer to “Parental Lock” (੬ pg. 40).
menu display may appear on the TV screen after starting playback.
In this case, select an item which you want to play back from the
menu. Otherwise, the playback cannot go forward. Refer to
“Playback Control (PBC) Function” (੬ pg. 31) or “Locating A Desired
Scene Using The DVD Menu” (੬ pg. 28).
8
9
CABLE/DBS
TV DVD
● The Library Database Navigation also enables you to search and
select the desired titles. (੬ pg. 64)
DVD
4 Press 9 to pause playback.
● To resume normal playback, press 4.
5 Press 8 to stop playback.
● When a recordable disc is played, playback stops and a program
received with the unit’s tuner resumes on the TV screen.
● When a playback-only disc is played, playback stops and the still
● If x is pressed during playback, playback stops, then the disc tray
opens.
ENTER
NOTES:
● When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
ENTER. (੬ pg. 64)
4
8
9
● It is not possible to playback the DVD disc recorded in 96 kHz on
DVD during recording or Live Memory Playback on HDD.
ATTENTION:
● It takes approximately 30 seconds to read a disc depending on the
type and condition of the disc since this unit is multi-disc
compatible (DVD-RAM, DVD-RW, DVD-R). It may even take
several minutes when a disc is dirty, scratched or warped.
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations cannot
be performed while playback is stopped.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
28
Locating The Start Point Of The Item Or Skip The Item
Playback Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
Press 2 or 6 during playback.
● Pressing 6 locates the start point of the item or skips the item in
the forward direction, then resumes playback.
● Pressing 2 locates the start point of the item or skips the item in
the reverse direction, then resumes playback.
CABLE/DBS
TV
DVD
When a DVD-RAM/RW/R disc is played
Current program
DVD
0-9
MARK
Previous
program
Next
program
News
Drama
Movie
TOP MENU
ENTER
rtwe
6
Reverse
● : marked points (੬ pg. 29)
Forward
MENU
2
4
Example:
5/SLOW +
9
3/SLOW
-
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
To locate the beginning of the previous item, press 2 three
times.
8
When a DVD VIDEO, Audio CD or Video CD/SVCD disc is
played
Playback point
Locating A Desired Scene Using The DVD Menu
Scene 2
(Chapter 2)
or
Scene 3
(Chapter 3)
or
Scene 4
(Chapter 4)
or
DVD VIDEO discs may have top menu and disc menu.
Track 2
Track 3
Track 4
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Reverse
Forward
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
Disc menu
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
High-Speed Search
Press MENU to access the disc menu.
1 Press TOP MENU or MENU to
access the DVD menu.
2 Press rt w e to select a
desired title, then press ENTER.
Playback starts.
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
● Each press of the button increases the search speed for each
direction.
desired item using the number
keys depending on the menu
● To resume normal playback, press 4.
display.
Example:
For Audio CD
NOTE:
You can perform 4 levels of speed search with 5 and 3.
(Audio is active also during high-speed search.) You cannot
perform slow motion for each direction.
When “X” appears on the TV screen
in step 1, the disc does not have a top menu or disc menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
29
NOTES:
Still Picture/Frame-By-Frame Playback
● “DISC RESUME” setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other
types of discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”. (੬ pg. 82)
● If you stop the playback of a disc for which a resume point has
already been memorized, the memory will be updated with the new
resume point.
● After the unit has memorized the resume points for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorized point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) to activate frame-by-
frame playback.
● Each press of SLOW – (3) or SLOW + (5) advances/reverses
the still picture frame by frame.
● Frame-by-frame playback for reverse direction cannot be performed
with Video CD/SVCD discs.
● To resume normal playback, press 4.
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CD/SVCDs.
● When “RESUME” is changed to “ON” or “OFF” (੬ pg. 82), resume
points of the discs memorized with “RESUME” set to “DISC
RESUME” will be cleared.
Slow Motion
● Resume points are memorized for each side of a double-sided disc.
● When you switch to HDD during CD playback, playback stops. The
Resume Function doesn’t work when you switch to DVD thereafter to
playback the disc.
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) for 2 or more seconds.
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
Marking Positions To Play Back Again Later
● Slow motion for reverse direction cannot be performed with Video
CD/SVCD discs.
Skip Search
It is possible to mark positions (up to 999 points) where you want
to play back once again later, and start playback from a marked
position. Marking onto DVD-RAM/RW (VR mode only) discs when
recording is helpful to locate a start point when you play back the
discs later.
During playback, press
● Each press initiates an approximately 30-second period of fast-
.
motion playback. Normal playback resumes automatically.
To mark positions:
During playback, press MARK at
positions you want to mark.
● “MARK” appears on the TV screen.
You can easily locate the marked
positions using 2 or 6 when you
play back the disc.
Resume Function
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set “RESUME” to “ON” or “DISC RESUME”. (੬ pg. 82)
To delete the marked positions:
While paused, press 2 or 6 to
locate a marked position you want to
delete, then press MARK.
● Crossed “MARK” appears on the TV
screen, and the marked position is
deleted.
● The unit enters Resume Stop mode and memorizes the position
where you have stopped playback as a resume point. (The inside of
the disc status indicator on the front display panel blinks while
memorizing.)
● The unit retains a memory of the resume points of the last 30 discs
played back, even though they have been ejected if “RESUME” is set
to “DISC RESUME”. (੬ pg. 82)
NOTES:
recording, a mark signal is automatically recorded.
● Titles will be divided into “chapters” at the marked points according to
the disc types as follows:
● To clear the resume points:
(The inside of the disc status indicator stops blinking and lights.)
When “RESUME” is set to “ON”:
• Press 1 to turn off the unit.
• Press x to take out the disc.
• Press 8 in stop mode.
DVD-R/RW (Video mode): After finalizing, titles are divided into
“chapters” at the marked points that are marked automatically
approximately every 5 minutes during recording before finalizing.
(੬ pg. 88)
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
When “RESUME” is set to “DISC RESUME”:
• Set “RESUME” to “OFF”. (੬ pg. 82)
DVD-RW (VR mode): After finalizing, titles are divided into “chapters”
at the marked points that are marked at the desired locations during
playback before finalizing. (੬ pg. 88)
DVD-RAM: Titles are divided into “chapters” at the marked points that
are marked at the desired locations during playback.
DVD VIDEO: Creating of marked points are not permitted.
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
2 Press 4 in stop mode to resume playback. The unit starts
playback from the resume point.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
30
Angle Selection
CABLE/DBS
TV DVD
DVD
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains “multi-angle” parts, where the same scene was shot from
different angles.
0-9
If the disc contains “multi-angle” parts, “
” appears on the TV
screen at the beginning of the “multi-angle” part.
1 Press ANGLE during playback.
The angle selection display
appears on the TV screen.
ENTER
rtwe
When 3 scene angles are
contained.
MENU
RETURN
NEXT
2 Press ANGLE or w e to select
your desired angle.
PREVIOUS
● Each time you press ANGLE or
w e, the angle changes.
4
8
● When “X” appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit angle
selection.
● To clear the angle selection display, press ENTER. In addition, the
angle selection display disappears automatically if no operation is
done for 10 seconds.
REMAIN
DISPLAY
SET UP
ANGLE
AUDIO
SUBTITLE
Subtitle Selection
Checking The Time Information
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
“
” appears on the TV screen at the beginning of the part where
You can check time information of a disc on the front display panel
and the TV screen.
Each press of DISPLAY changes the display as follows:
more than one subtitle language are recorded.
1 Press SUBTITLE during
ENGLISH
playback. The subtitle selection
display appears on the TV screen.
8 DVD-RAM/DVD-R/DVD-RW
During recording
Clock time (front display panel only) ] Current title elapsed time
] Disc remaining time* ] (back to the beginning)
* only discs before finalizing
● Clock time is displayed only when a recordable disc is recorded.
During playback
Each title elapsed time ] Current title elapsed time ]
Disc remaining time* ] (back to the beginning)
* only discs before finalizing
When 3 subtitle languages are
contained.
● Each time you press SUBTITLE,
the subtitle display is switched on
and off.
2 Press w e to select your desired language.
● To clear the subtitle selection display, press ENTER.
NOTES:
● When “X” appears on the TV screen, no subtitle language is
recorded.
● When the subtitle language won’t be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
In stop mode or during playback
● It is possible to check disc remaining time according to recording
modes also by pressing REMAIN.
● In FR mode, it is possible to set recording time in detail. While the
recording mode and the disc remaining time are displayed by
pressing REMAIN, press rt to select “FR”, then press w e to
select the desired recording time. (੬ pg. 43)
● It is not possible to switch the recording mode during playback or
while recording.
8 Video CD/SVCD/Audio CD
During playback
Current track elapsed time ] Current track remaining time ]
Total elapsed time ] Total remaining time ] (back to the
beginning)
In stop mode
0:00 ] Playback time of track 1 ] 0:00 ] Total length of a disc ]
(back to the beginning)
NOTE:
When a PBC-compatible Video CD/SVCD disc is loaded, deactivate
the PBC function. (੬ pg. 31)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
31
program
Audio Language/Sound Selection
When the unit is connected with a digital audio device using an
optional optical cable and “DIGITAL AUDIO OUT” is set to “DOLBY
DIGITAL/PCM”, it is not possible to switch the audio channel of a
bilingual program recorded on a DVD-RAM or DVD-RW (VR
mode) disc. (੬ pg. 80) In this case, perform the following steps
using the remote control to switch “DIGITAL AUDIO OUT” from
“DOLBY DIGITAL/PCM” to “PCM ONLY”.
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD/SVCD discs, you can switch the audio channel to
choose Karaoke either with or without the vocal.
B Press w e to select “DVD VIDEO SET UP”, then press t.
C Press w e to select “AUDIO OUTPUT”, then press t.
D Press rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
1 Press AUDIO during playback.
The Audio Language/Sound
selection display appears.
When 3 audio languages are
contained.
2 Press AUDIO or w e to select
your desired audio language/
E Press rt to select “PCM ONLY”, then press ENTER.
sound.
(੬ pg. 81)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
● Each time you press AUDIO or w e, the audio language/sound
changes.
● To clear the Audio Language/Sound selection display, press ENTER.
NOTES:
Playback Control (PBC) Function
● When “X” appears on the TV screen, no audio language is recorded.
● When the audio language won’t be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
● Pressing AUDIO to select the audio language/sound is only possible
during playback. It is not possible to select by pressing AUDIO in
stop mode. However, you can select the desired audio language/
sound from the setup menu while in stop mode.
Some Video CD/SVCD discs support the PBC function. PBC is an
abbreviation of “Play Back Control”. A Video CD/SVCD disc
recorded with PBC has its own menus, such as a list of the songs
on the disc. You can locate a specific scene by using the menu.
1 Press 4 in stop mode. The PBC menu appears.
Audio Channel Selection
2 Press the number keys to enter the number of the desired
scene. The unit starts playback of the selected item.
● “PBC” appears on the front display panel.
● When “NEXT” or “PREVIOUS” appears on the TV screen:
Pressing NEXT (6) advances to the next page.
Pressing PREVIOUS (2) returns to the previous page.
● You can return to the menu by pressing RETURN.
● The method of the operation is different depending on the disc.
When watching bilingual programs or playing discs on which you
recorded bilingual or stereo programs, you can choose the desired
audio channel.
● When “SUPERIMPOSE” is set to “AUTO”, you can confirm on the TV
screen the audio channel you have chosen. (੬ pg. 82)
● Each time you press AUDIO, the audio channel
changes.
NOTES:
● If you want to playback a PBC-compatible Video CD/SVCD disc
without activating the PBC function, start playback in stop mode by
using the number keys, instead of the 4 button, to choose the track,
then press ENTER.
TRACK
● To activate the PBC function when a PBC-compatible Video CD/
SVCD disc is being played back without the PBC function, press TOP
MENU, or press 8 then press 4.
USE
On-Screen Display
For stereo discs
For audio of left channel
For audio of right channel
NOTE:
It is not possible for DVD-R/DVD-RW (Video mode) disc playback to
switch the audio channel. The audio channel is played back as set in
“VIDEO MODE RECORDING AUDIO” setting. (੬ pg. 82)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
32
Recording/playback Status Display
Live Memory Playback
CABLE/DBS
TV
DVD
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
This unit records pictures onto the DVD-RAM discs, instead of
video tapes, then plays back the pictures recorded on the discs.
This makes it possible to achieve high-speed writing and read-out
that has not been possible with conventional VCRs, enabling
recording and playback simultaneously.
LIVE
High-speed spin
Recording
(High-speed writing)
Playback
(High-speed read-out)
ON SCREEN
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display.
Image figure of DVD-RAM disc
It is called “Live Memory Playback” to start playback of the
program being recorded, with a time-lag between a recording point
and a playback point, as shown in the figure below.
Press ON SCREEN. The current status is superimposed on the TV
screen.
Current playback point
(Live Memory Playback)
Current recording position
Bar meter display
Recording start point
(Recording point)
Playback
continues
Recording
continues
0
30 min.
1 hour
Currently elapsed recording time
Not only can this unit play back a program previously recorded
while recording or timer recording another program, but the unit
also allows you to play back from the beginning of a program while
continuing to record the same program.
Superimpose display
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
33
Overview Of Live Memory Playback
You can play back a program you are recording from the beginning while continuing to record or timer record onto a DVD-RAM disc. This
is called “Live Memory Playback”.
(Recording screen)
(Live Memory Playback screen)
To start Live Memory Playback,
press 4 to play back from the
beginning OR press
reverse-skip a little
to
To stop Live Memory
Playback, press 8
Checking the
picture currently
being recorded
To clear, press
LIVE CHECK
To display, press
LIVE CHECK
To stop recording,
press 8 OR LIVE
(Playback and Live Check screen)
To stop Live Memory Playback,
Recording
stops
press 8
Live Memory Playback
picture
Recording
picture
CABLE/DBS
NOTES:
TV
DVD
● Live Memory Playback could be performed approximately 30
seconds after recording has started.
● Although high-speed search up to approximately 30 seconds before
the current recording point is possible during Live Memory
Playback, once the current recording point is reached, the unit
resumes normal playback and maintains a delay of approximately
● When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
● When using Live Memory Playback during timer recording, playback
is automatically stopped just before recording starts, and then
recording starts when the time arrives for the next timer-program.
NAVIGATION
Press NAVIGATION to display Library
Database DVD Navi menu, then choose a
program to play back. (੬ pg. 63)
Press 8 to display the program being recorded, then perform ITR
settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (੬ pg. 74, “DV Dubbing (HDD & DVD Deck
Only)”)
● When LIVE CHECK is pressed to display the picture currently being
recorded, the picture size may not be correct.
ON SCREEN
LIVE CHECK
Pressing LIVE CHECK during Live Memory
Playback allows you to check the picture
currently being recorded.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
34
Display During Live Memory Playback
During recording, you can watch at your will what was previously recorded or is currently being recorded. It is possible to perform freely
normal playback operations (forward/reverse high-speed search and variable-speed search) within the range of the red or blue bar on the
TV screen.
When Live Memory Playback reaches the point of 30 seconds before the current recording point by forward high-speed search or other
operations, the unit returns to normal playback.
The superimpose display appears by pressing ON SCREEN. (੬ pg. 16)
The Live Check picture is displayed on the bottom right corner by pressing LIVE CHECK.
Recording counter display
(remaining time)
Recording mark
Disc used
Recording channel
Live Memory Playback mark
Recording mark
Recording mode
Bar meter (see below)
Live Check picture
This unit displays the current recording/playback status by the bar meter.
(Example of bar meter display)
Capacity of a disc
Recorded
Not recorded
While stopped
Total length of the program being played
Current playback position
During playback
Capacity of a disc
Remaining capacity when recording started
Current recording position
While recording
Capacity of a disc
Current playback position
Recording start position
Current recording position
Live Memory Playback
Capacity of a disc
Recording start position
Current recording position
Current playback position
Live Memory Playback of
another program
Total length of the program being played back
Blue (recorded part)
Green (playing part)
Black (unrecorded or unplayed part)
Orange (recording part)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
35
G 8
● Pressing once during Live Memory Playback or Live Memory
Buttons To Be Used During Live Memory Playback
Recording returns to the screen on air.
● Turn on the unit.
● Pressing twice during recording stops recording and returns to the
screen on air.
H 9
Pressing once pauses playback (still picture playback). Pressing
repeatedly advances the still picture frame by frame.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
I JUMP –
CABLE/DBS
jumps back for the selected time interval and resumes playback.
(੬ pg. 49, “Jump Search”)
TV
DVD
DVD
J JUMP +
Each press of the button during playback or Live Memory Playback
jumps forward for the selected time interval and resumes playback.
(੬ pg. 49, “Jump Search”)
K
Pressing once skips forward for approximately 30 seconds and
resumes playback.
A
B
Pressing repeatedly skips forward continuously as many times as
pressed.
It is useful when skipping over unwanted sections.
L
Pressing once skips back for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
It is useful when watching sports programs, etc.
M LIVE CHECK
Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
Pressing successively clears the Live Check window and displays
only the picture currently being played back.
You can check, for example, if the program you are recording has
already finished.
C
E
G
D
F
H
I
J
K
L
M
A LIVE
Returns to on air program screen. When a confirmation message
appears by pressing this button during timer programming or title
editing, etc., follow the instruction to return to the previous screen.
B NAVIGATION
Displays Library Database Navigation menu. You can choose a
title to play back.
C 2
● Pressing once skips back to the beginning of the chapter being
played back.
● Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
To Play Back From The Beginning Of The Program
While Recording
You can play back a program you are recording from the beginning
while continuing to record or timer record onto a DVD-RAM disc.
Press 4. Live Memory Playback starts from the beginning of the
program being recorded.
● Pressing 2 or 6 allows you to locate the desired scenes.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed.
D 6
● Pressing once skips forward to the beginning of the next chapter
being played back.
● Pressing down for 2 or more seconds during playback advances
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
To Move Back The Playback Position Slightly While
Recording (One Touch Replay Function)
You can move back the playback position while continuing to
record or timer record onto a DVD-RAM disc.
Press
.
● Each press skips back for approximately 7 seconds and resumes
Available only when paused
playback.
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed.
E 3
● Pressing while paused skips back for approximately 7 seconds and
resumes pause.
● Each press of the button during playback advances the playback
speed in 5 steps in the reverse direction.
Available only when paused
● Each press of the button reverses the still picture frame by frame.
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed. Then, each press of the button reverses
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
To Watch A Program Previously Recorded While
Recording
You can play back a program you recorded previously while
recording.
1 Press 4 during recording. Live Memory Playback starts.
F 5
2 Press 2 or 6 to locate the beginning of the desired
● Each press of the button during playback advances the playback
speed in 4 steps in the forward direction.
Available only when paused
program.
NOTE:
● Each press of the button advances the still picture frame by frame.
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed. Then, each press of the button advances
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
To stop playback, press 8. The program being recorded is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
36
B Select this for Repeat Playback. (੬ pg. 37)
C Select this for A-B Repeat Playback. (੬ pg. 37)
D Select this for search function. (੬ pg. 37)
(੬ pg. 38)
H Select this to switch picture source type. (੬ pg. 39)
I Current status area for the selected item.
J Select this for Program Playback. (੬ pg. 39)
K Select this for Random Playback. (੬ pg. 39)
L Select this to control the switching interval of the slide show.
(੬ pg. 39)
Using The On-screen Bar
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
ATTENTION:
The on-screen bar can also be used for the HDD deck.
Be sure to clear Library Database Navigation screen by pressing
NAVIGATION.
NOTE:
Although examples of the on-screen bar are provided here only for 3
types of discs, the on-screen bar will be displayed for whichever disc
indicated in the left column.
CABLE/DBS
TV
DVD
Basic Operation On The On-screen Bar
Example: When selecting Picture Control function of DVD
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar. The item
currently selected is highlighted and pointed by H.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
NAVIGATION
ENTER
CLEAR
DVD-
rtwe
VIDEO
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
ON SCREEN
DVD-
VIDEO
3 Press rt to select the desired option, then press ENTER.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
DVD-
How To Access The On-screen Bar
VIDEO
NORMAL
CINEMA
SHARP
SOFT
1 Press ON SCREEN twice whenever a disc is loaded.
Contents of the on-screen bar during playback
DVD VIDEO
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
To clear the on-screen bar
Press ON SCREEN.
DVD-
NOTE:
VIDEO
See the corresponding pages for details on each menu item.
Video CD/SVCD
TRACK 99
EACH 0:00
CINEMA
VCD
JPEG disc
GROUP 99 TRACK 99
5 SEC.
JPEG
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
37
To clear the on-screen bar
Press ON SCREEN.
Repeat Playback
To cancel A-B Repeat Playback
Press w e to select “
”, then press ENTER.
NOTES:
You can repeat playback as you like according to the type of disc.
● A-B Repeat Playback may not work properly depending on the type
of disc being used.
● The subtitles recorded around the A-B point may not appear.
● When the end of the item is reached before the end point is set, the
on-screen bar disappears from the TV screen. In such a case, repeat
the procedure from step 1.
● The point B must be set at least 3 seconds after the point A.
● When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99 CHAPTER 99 EACH 0:00
3D-ON CINEMA AUTO
DVD-
VIDEO
● “
Playback.
● “
” cannot be selected during Program and Random
3 Press rt repeatedly to select the desired Repeat mode, then
press ENTER.
” cannot be selected while stopped.
DVD-RAM/RW/R
Locating The Beginning Of A Desired Selection
OFF: Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
TITLE REPEAT: The current title is played back repeatedly.
DVD VIDEO
OFF: Repeat playback is not performed.
TITLE REPEAT: The current title is played back repeatedly.
CHAPTER REPEAT: The current chapter is played back repeatedly.
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER.
Audio CD/Video CD/SVCD/JPEG/MP3
OFF: Repeat playback is not performed.
3 Press rt to select the desired item, then press ENTER.
ALL REPEAT: The whole disc is played back repeatedly.
GROUP REPEAT*: The current group is played back repeatedly.
● Skip this step for Video CD/SVCD and Audio CD.
For DVD-RAM/RW/R, DVD VIDEO
SEARCH” is selectable only while stopped.)
TRACK REPEAT*: The current track is played back repeatedly.
discs.
* “TRACK REPEAT” cannot be selected for JPEG discs.
For JPEG, MP3
“GROUP SEARCH” or “TRACK SEARCH” is selectable.
To clear the on-screen bar
Press ON SCREEN.
For Video CD/SVCD, Audio CD
“TRACK” is selectable.
To cancel Repeat Playback
Repeat the above procedure from step 1, select “OFF” in step 3,
then press ENTER.
GROUP 99
CHAPTER 99
EACH 179:59
5
CINEMA
NOTES:
DVD-
● Repeat Playback is not possible for a Video CD/SVCD with PBC
VIDEO
function.
TITLE SEARCH
CHAPTER SEARCH
● Repeat Playback may not work properly depending on the type of the
disc being used.
4 Press the number keys to enter the desired item number, then
A-B Repeat Playback
press ENTER.
● Playback starts from the selected section.
Examples:
A To select track 5, press the number key “5”.
B To select track 15, press the number key “1” and “5”.
C To select track 25, press the number key “2”, then “5”.
You can repeat the desired part.
During playback
If you have specified a wrong selection
Press RETURN on the remote control unit and repeat the above
procedures from step 2.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”.
To clear the on-screen bar
Press ON SCREEN.
3 Press ENTER at the beginning of the desired part you want to
repeat (point A). The elapsed playing time of the point A appears.
NOTES:
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
● When “X” is displayed on the TV screen in step 4, the chapter you
have selected is not contained in the disc, or chapter search does not
work on the disc.
DVD-
VIDEO
● Before you press ENTER, playback may start automatically when
you enter the section’s number depending on the disc.
● This function is not possible for a Video CD/SVCD with PBC function.
A
1 : 25 : 58
B
:
:
4 Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
● The selected part of the disc (between point A and B) is played
repeatedly.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
DVD-
VIDEO
A
1 : 25 : 58
B
1 : 40 : 00
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
38
Simulated Surround Effect
CABLE/DBS
TV DVD
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your
2-channel stereo system.
0-9
1 Press ON SCREEN twice to access the on-screen bar.
CANCEL
2 Press w e to select “
”, then press ENTER.
● “3D-ON” appears above the selected item and Simulated Surround
Effect is activated.
● Each time you press ENTER, “3D-ON” appears and disappears
ENTER
rtwe
6
alternately.
2
TITLE 99
DVD-
CHAPTER 99
EACH 0:00
3D-ON CINEMA AUTO
4
CLEAR
VIDEO
ON SCREEN
To clear the on-screen bar
Press ON SCREEN.
To cancel the simulated surround effect
Press ENTER to clear “3D-ON” from the screen.
NOTES:
● Simulated Surround Effect works correctly only when playing back a
title recorded in multichannels.
● Simulated Surround Effect does not affect the DVD VIDEO bitstream
signal from the [DIGITAL AUDIO OUT] connectors.
● When Simulated Surround Effect is activated, the settings of
“ANALOG AUDIO OUT” and “D. RANGE CONTROL” are disabled.
(੬ pg. 81)
Time Search
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a program (DVD-RAM,
DVD-R, DVD-RW, DVD VIDEO and HDD) or a disc (Video CD/
SVCD and Audio CD).
Adjusting The Picture Quality
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”, then press ENTER. The pop-up
You can obtain optimal picture quality by selecting an appropriate
picture mode.
window appears under the selected item.
TITLE 99 CHAPTER 99 EACH 0:00
CINEMA AUTO
1 Press ON SCREEN twice to access the on-screen bar.
DVD-
2 Press w e to select “
”, then press ENTER. The pop-up
VIDEO
window appears under the selected item.
TITLE 99 CHAPTER 99 EACH 0:00
CINEMA AUTO
3 Press the number keys to enter the time, then press ENTER.
Playback starts from the specified time.
Example:
DVD-
VIDEO
To play back from a point 12 (minutes): 50 (seconds) elapsed.
3 Press rt to select the desired option, then press ENTER.
NORMAL: Normally select this option.
Press 1
Press 5
Press 2
Press 0
CINEMA: Suitable for a movie disc, etc.
SHARP: Clearer, sharper-edged picture when viewing images with
lots of flat, same-colored surfaces such as cartoons.
SOFT: Select this option when too much noise appears.
To clear the on-screen bar
Press ON SCREEN.
If you have specified a wrong selection,
Press RETURN on the remote control unit and repeat the above
procedures from step 2.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When “X” is displayed on the TV screen in step 3, you have selected
a point that exceeds the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is not
possible to use the Time Search function. In such cases, “X” is
displayed on the TV screen as well.
● This function is not possible for a Video CD/SVCD with PBC function.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
39
4 Press 4. Playback starts in the programmed order.
Setting The Progressive Mode
● When all of the programmed tracks have been played back, Program
Playback stops, but the programmed information remains.
● To add tracks to the end of the program, perform steps 1 through 3.
● During Program Playback, pressing 6 skips to the next selection
of the program. Pressing 2 returns to the beginning of the current
selection.
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
To clear the on-screen bar and the contents of the program
Press ON SCREEN.
1 Set the unit to the progressive scan mode. (੬ pg. 83)
2 Press ON SCREEN twice to access the on-screen bar.
To cancel Program Playback
Press w e to select “PRGM”, then press ENTER.
3 Press w e to select “
”, then press ENTER. The pop-up
NOTE:
window appears under the selected item.
TITLE 99 CHAPTER 99 EACH 0:00
3D-ON CINEMA AUTO
Program Playback is not possible depending on the type of disc.
Random Playback
DVD-
VIDEO
4 Press rt to select the desired option, then press ENTER.
AUTO: This mode automatically detects film and video content for
progressive playback. When film content is found, flag detection
is used to invoke playback of film data in full screen. When video
content is found, pictures from multiple fields are used to detect
sections with movement, and then this movement undergoes
advanced image processing for output of sharp, detailed
progressive images without any reduction in image quality where
movement occurs. Normally, operation in this mode is
recommended.
You can play back all the tracks on the disc in random order.
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “RND”, then press ENTER. Playback starts
in random order.
TRACK 99
EACH 0:00
CINEMA
VCD
FILM: Suitable for playing back a progressive scanned film source
disc.
VIDEO: Suitable for playing back a video source disc. The outlines
on the played back pictures will be soft.
To clear the on-screen bar
Press ON SCREEN.
To clear the on-screen bar
Press ON SCREEN.
To cancel Random Playback
Perform steps 1 and 2.
NOTE:
Program Playback
The same track will not be played back more than once during Random
Playback.
Select The Switching Interval Of The Slide Show
You can program up to 30 tracks (Video CD/SVCD or Audio CD) to
play back in the desired order.
While stopped
You can control the switching interval of the slide show.
1 Press ON SCREEN twice to access the on-screen bar.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “PRGM”, then press ENTER. The program
table appears under on-screen bar.
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
TRACK 99
EACH 0:00
GROUP 99 TRACK 99
CINEMA
VCD
5 SEC.
JPEG
3 Press the number keys to
enter the track numbers in the
desired order.
3 Press rt to select the desired option, then press ENTER.
● Each time you press rt, the interval changes as follows:
5 SEC. { 10 SEC. { 15 SEC. { 20 SEC. { 25 SEC. {
30 SEC. { (Back to the beginning)
Examples:
A To select track 5, press the
number key “5” and ENTER.
B To select track 15, press the
number key “1” and “5”.
To clear the on-screen bar
Press ON SCREEN.
NOTE:
C To select track 25, press the number key “2” and “5”.
JPEG files are played back as a slide show. It may take more time to
display an image with larger file size.
If you have specified a wrong selection
Press CANCEL (&). The last selection is erased.
Or press CLEAR (8). The whole selection is erased.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
40
9 Press the number keys to enter the same password as in
step 6 above, then press ENTER.
Parental Lock
10Press SET UP to complete the setting.
NOTE:
This function restricts playback of DVD VIDEO discs which contain
violent (and other) scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the
parental lock feature, such scenes which you do not want to let
children view can be cut or replaced by other scenes.
To Change The Settings
You can change the Parental Lock settings later.
1 Perform steps 1 to 3 of “To Set Parental Lock For The First
Time” to access the “PARENTAL LOCK” screen before continuing.
● Turn on the unit.
To change the level
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
3 Press rt to select the desired level, then press ENTER.
CABLE/DBS
4 Press rt to select “COUNTRY CODE”, then press ENTER.
TV
DVD
5 Press rt to select your country code, then press ENTER.
● See “Country/Area Code List for Parental Lock” (੬ pg. 95).
DVD
6 Press the number keys to enter the same password as in
step 6 of “To Set Parental Lock For The First Time”, then press
ENTER.
0-9
7 Press SET UP to complete the setting.
NOTE:
If you forget your password, enter “8888” in step 6.
ENTER
rtwe
To Temporarily Release Parental Lock
When you set the Parental Lock level strictly, some discs may not
be played back at all. When you insert such a disc and try to play it
back, the confirmation screen appears on the TV screen, asking
you whether you want Parental Lock to be temporarily released or
not.
SET UP
1 Load a disc.
● If the disc is rated higher than the selected level, the confirmation
screen appears.
2 Press w e to select “YES”, then press ENTER.
● If you select “NO”, you cannot play back that disc.
3 Press the number keys to enter the same password as in
step 6 of “To Set Parental Lock For The First Time”, then press
ENTER.
● When you enter the correct password, the Parental Lock is released
and the unit starts playback.
To Set Parental Lock For The First Time
While stopped
● If you enter a wrong password, “ENTRY ERROR” appears on the TV
screen. Enter the correct password.
● If you have successively entered wrong password three times,
“ENTRY ERROR CAN NOT CHANGE PASSWORD” appears on the
TV screen. In such a case, press ENTER. The disc will stop. Then
play back the disc again, and try the procedure again from step 1.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “DVD VIDEO SET UP”, then press t.
3 Press w e to select
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
DISC SET UP
“PARENTAL LOCK”, then press
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LOCK
t.
PARENTAL LEVEL
COUNTRY CODE
NONE
US
NOTE:
If you forget your password, enter “8888” in step 3.
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
4 Press rt to select
“PARENTAL LEVEL”, then press
ENTER.
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
LANGUAGE SET AUDIO OUTPUT PARENTAL LOCK
INITIAL SET UP
DISC SET UP
PARENTAL LEVEL
COUNTRY CODE
NONE
US
5 Press rt to select the desired
level, then press ENTER.
● The smaller the value of level is,
the more restrictive the Parental
Lock level becomes.
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
● Select “NONE” to cancel the
restriction.
then press ENTER.
● If you made a mistake, enter a correct number again.
7 Press rt to select “COUNTRY CODE”, then press ENTER.
8 Press rt to select your country code, then press ENTER.
● If you do not need to change your country code, jump to 10.
● See “Country/Area Code List for Parental Lock” (੬ pg. 95)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
41
7 Press 8 twice to stop recording.
Basic Recording
recording.
NOTES:
● It is recommended to format a DVD-RAM disc before use if you use
the disc on this unit for the first time.
● When using a brand-new DVD-RW disc, format the disc either in VR
mode or in Video mode. (੬ pg. 87)
on other DVD players. Perform “Finalize A Disc (DVD Deck Only)”
(੬ pg. 88).
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● You can record up to 99 programs and 999 play lists on each disc.
● Some programs can only be recorded one time.
● When recording is started, an index of the first part of recording is
automatically recorded. (੬ pg. 63) To record satellite programs,
refer to page 59. To delete the index, refer to page 65.
● Recording sometimes may stop or cannot be performed even if there
is enough available capacity remaining on the disc.
● It is not possible to record on both DVD and HDD simultaneously.
ATTENTION:
It is not possible to record programs on a DVD-R disc which has
already been finalized.
VHS/HDD/DVD
SELECT
4 9
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
7
8
CH +/
REC
MODE
CABLE/DBS
TV DVD
The recording modes for a 4.7 GB disc are set as follows:
DVD
Recording
mode
Recording amount
(approx.)
Maximum recording
time (approx.)
0-9
XP
10 Mbps
1 hour
CH+/-
SP
LP
EP
5 Mbps
2 hours
2.5 Mbps
1.6 Mbps
4 hours
ENTER
6 hours
FR60–FR360 The amount varies
1 – 6 hours
(੬ pg. 43)
depending on the
selected time.
4
FR420
7 hours
8 hours
7
8
9
FR480
REC MODE
● For details on FR mode, refer to “Free Rate Function” (੬ pg. 43)
1 Load a recordable disc.
● For details, refer to “Placing A Disc” (੬ pg. 10).
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD
on the remote so that the DVD lamp lights up on the unit.
3 Press CH +/– or the number keys to select the channel you
wish to record.
4 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
●
Each time you press REC MODE, the recording mode changes as follows:
XP ] SP ] LP ] EP ] FR60–FR360* ] FR420, FR480 ] (Back
to the beginning)
* The value is selectable from 1 to 6 hours in 5-minutes interval by
pressing w e repeatedly after selecting “FR60–FR360”. To change the
value in 30-minutes interval, press and hold w e.
● For details on the recording mode, see the right column.
5 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control.
● The DVD recording lamp lights up on the unit.
6 Press 7 and 9 on the remote control simultaneously to pause
recording.
● To resume recording, press 7 and 4 simultaneously.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
42
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
Recording Features
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
● Turn on the unit.
● On the front display panel, “0:30” appears.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD on
the remote so that the DVD lamp lights up on the unit.
extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the 7 button on the unit.
● When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit automatically performs “Relief
Recording” (੬ pg. 57).
VHS/HDD/DVD
SELECT
While recording is going on, you can watch another program on
the TV by using the TV’s tuner.
7
DISPLAY
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (੬ pg. 78)
CABLE/DBS
TV
DVD
1 During recording, press TV/VIDEO to select TV mode if your
unit is connected to the TV via the RF connection.
● VHS mode is disengaged, and the VIDEO indicator on the front
display panel lights off .
TV / VIDEO
DVD
VIDEO indicator lights off.
CH+/-
● The program received on the TV’s tuner is displayed on the TV
screen.
2 Slide the TV/CABLE/DBS/DVD switch to TV.
3 Press CH +/– repeatedly to select the desired channel.
Elapsed Recording Time And Disc Remaining Time
Indication
REMAIN
DISPLAY
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of disc
remaining times for all recording modes appears on the TV screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
43
NOTES:
● You can program this unit to timer-record, regardless of the disc
Free Rate Function
To record the entire program, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the program to be recorded and either the remaining
minutes).
remaining time. When the disc remaining time is not enough, the unit
performs “Relief Recording” (੬ pg. 57). To avoid this, make sure of
the disc remaining time before setting timer programming.
mode on a 120-minute disc, the disc remaining time would be 30
minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP
mode, 180 minutes in EP mode, and 240 minutes in FR480 mode.
Timer-recording will not complete beyond these remaining times.
● The maximum recording time of FR (JUST) mode is the same as the
recording time of FR480 mode. When timer programming a long
program in FR (JUST) mode on a disc whose remaining time is short,
it is recommended to check the disc remaining time in FR480 mode
to see if the remaining time is enough for the program.
● Even if more than one program are timer programmed in FR (JUST)
mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature may
leave a slight non-recorded section at the end of the disc.
disc where the unit switches the mode.
8 To record the entire program within the actual remaining
disc space (DVD deck only)
● Note that this function is available only for timer programming
recording (੬ pg. 55, 57) and dubbing from HDD to DVD (੬ pg. 70).
recording time
Select “FR60–FR360”, “FR420” or “FR480” in a recording mode
selection procedure. (੬ pg. 41, 44, 55, 57)
8 To record a 25-min. long daily program five times just on
the same DVD disc for example
Perform “VCR Plus+ C ® Timer Programming” (੬ pg. 55)
3
procedure. Be sure to set the recording mode to “FR125” and set
Weekly/Daily Rec Function to “MON–FRI” in step 8 to fit the total
recording time to the whole disc space.
Second Audio Recording
A: 1st
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set “2ND
AUDIO RECORD” to “ON”. (੬ pg. 82)
B: 2nd
C: 3rd
D: 4th
E: 5th
Blank
NOTE:
When the channel is changed on the unit;
● The “MONO” indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
● Both “MONO” and “SAP” indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
When the same program is recorded in SP mode instead of in
“FR125”, the 5th program cannot be recorded.
A: 1st
B: 2nd
C: 3rd
Blank
D: 4th
E: Blank (20 min.)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
44
Pause recording on HDD deck
It is not possible to pause recording. Pressing 9 initiates Live
Memory Playback.
Basic Recording
However, it is still possible to pause recording only when recording
the channels of external sources (“L-1”, “F-1”, and “DV”). While
holding 7, press 9 on the remote. To resume recording, while
holding 7, press 4 on the remote.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
No operation can be made with the buttons on the unit.
ATTENTION:
Recording Mode
The HDD on the unit requires approximately 20 seconds to start up
after the unit has been turned on, during which no operation can be
made.
MPEG2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
VHS/HDD/DVD
HDD Lamp
SELECT
Recording
mode
Recording amount
(approx.)
Maximum recording
time (approx.)
XP
SP
LP
EP
10 Mbps
18 hours
7
8
CH +/
5 Mbps
35 hours
CABLE/DBS
TV DVD
2.5 Mbps
1.6 Mbps
70 hours
105 hours
18 – 105 hours
HDD
FR60–FR360
(੬ pg. 43)
The amount varies
depending on the
selected time.
0-9
FR480
147 hours
CH+/-
● For details on FR mode, refer to “Free Rate Function” (੬ pg. 43)
NOTE:
The maximum recording time stated in the above table are the
approximate time under unused condition.
4
8
7
9
REC MODE
1 Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
2 Press CH +/– or the number keys to select the channel you
wish to record.
3 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes as
follows:
XP ] SP ] LP ] EP ] FR60–FR360* ] FR420, FR480 ]
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5 minutes interval by
pressing w e repeatedly after selecting “FR60–FR360”. To change the
value in 30 minutes interval, press and hold w e.
● For details on the recording mode, see the right column.
4 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control.
● The HDD recording lamp lights up on the unit.
5 Press 8 twice to stop recording.
● Pressing 8 once displays the confirmation message to stop
recording. Press 8 again to terminate recording.
NOTES:
● Continuous recording for over 48 hours is not possible.
● It is not possible to record on both DVD and HDD simultaneously.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
45
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
Recording Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
VHS/HDD/DVD
HDD Lamp
SELECT
NOTES:
● You can only perform ITR using the 7 button on the unit.
● When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit is automatically shut off.
While recording is going on, you can watch another program on
the TV by using the TV’s tuner.
7
CH +/
DISPLAY
CABLE/DBS
TV DVD
NOTE:
It is required that the remote control is set to be able to operate the TV
TV / VIDEO
HDD
in advance. (੬ pg. 78)
1 During recording, press TV/VIDEO to select TV mode if your
unit is connected to the TV via the RF connection.
● VHS mode is disengaged, and the VIDEO indicator on the front
display panel lights off.
CH+/-
VIDEO indicator lights off.
● The program received on the TV’s tuner is displayed on the TV
screen.
2 Slide the TV/CABLE/DBS/DVD switch to TV.
3 Press CH +/– repeatedly to select the desired channel.
REMAIN
DISPLAY
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
● You can also check the disc remaining time by pressing REMAIN
remaining times for all recording modes appears on the TV screen.
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set “2ND
AUDIO RECORD” to “ON”. (੬ pg. 82)
NOTE:
When the channel is changed on the unit;
● The “MONO” indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
● Both “MONO” and “SAP” indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
46
Basic Playback
Playback Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD so that the HDD lamp lights up on the unit.
VHS/HDD/DVD
SELECT
4
CABLE/DBS
TV
DVD
HDD
8
9
CABLE/DBS
TV DVD
HDD
4
3/SLOW
-
5/SLOW +
9
ENTER
4
8
9
High-Speed Search
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press 4.
Still Picture/Frame-By-Frame Playback
ATTENTION:
● It may take a few seconds to start playback. This is not a
malfunction.
1 Press 9 to pause during playback.
● Forward/reverse high-speed search and other operations cannot
be performed while playback is stopped.
2 Press SLOW – (3) or SLOW + (5) to activate frame-by-
frame playback.
● Each press of SLOW – (3) or SLOW + (5) advances/reverses
the still picture frame by frame.
● To resume normal playback, press 4.
1 Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
2 Press 4 to start playback.
Slow Motion
1 Press 9 to pause during playback.
● The Library Database Navigation also enables you to search and
select the desired programs. (੬ pg. 64)
2 Press SLOW – (3) or SLOW + (5) for 2 or more seconds.
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
● To resume normal playback, press 4.
4 Press 8 to stop playback.
NOTE:
When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
ENTER. (੬ pg. 64)
Skip Search
During playback, press
.
● Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
47
Recording/playback Status Display
Live Memory Playback
CABLE/DBS
TV DVD
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD so that the HDD lamp lights up on the unit.
This unit records pictures onto the hard disc, instead of video
tapes, then plays back the pictures recorded on the disc. This
makes it possible to achieve high-speed writing and read-out that
has not been possible with conventional VCRs, enabling recording
and playback simultaneously.
LIVE
NAVIGATION
Press NAVIGATION to display Library Database
Navigation menu, then choose a program to play
back. (੬ pg. 63)
High-speed spin
Recording
Playback
(High-speed writing)
(High-speed read-out)
8
ON SCREEN
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display. The current status is
superimposed on the TV screen. (੬ pg. 17, “When
using Live Memory playback”)
Image figure of the hard disc
It is called “Live Memory Playback” to start playback of the
program being recorded, with a time-lag between a recording point
and a playback point, as shown in the figure below.
Current playback point
(Live Memory Playback)
NOTES:
● Live Memory Playback could be performed approximately 30
Current recording position
seconds after recording has started.
Recording start point
(Recording point)
● Although high-speed search up to approximately 30 seconds before
the current recording point is possible during Live Memory Playback,
once the current recording point is reached, the unit resumes normal
playback and maintains a delay of approximately 30 seconds so that
recording and playback can continue.
● When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
Playback
continues
Recording
continues
0
30 min.
1 hour
Currently elapsed recording time
● When using Live Memory Playback during timer recording, playback
is automatically stopped just before recording starts, and then
recording starts when the time arrives for the next timer-program.
Press 8 to display the program being recorded, then perform ITR
settings.
Not only can this unit play back a program previously recorded
while recording or timer recording another program, but the unit
also allows you to play back from the beginning of a program while
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (੬ pg. 74, “DV Dubbing (HDD & DVD Deck
Only)”)
recorded, the picture size may not be correct.
Temporary recording for Live Memory
This unit automatically records the channel being received, within
the specified range of time, to the reserved space on the hard disc.
The time range can be set for 30 minutes, 1 hour, and 3 hours.
(੬ pg. 82)
NOTE:
● Press 7 or LIVE to stop Live Memory Playback.
Previous temporary recordings will be overwritten since the unit is
always recording the channel being received. Thus, it is not possible to
play back TV programs recorded beyond the specified range of time
since they are already overwritten. To avoid this in order to save titles,
perform normal recording (੬ pg. 44), timer recording (੬ pg. 55, 57),
or Live Memory Recording (੬ pg. 49).
● Live Memory Playback cannot be performed even if the “LIVE
MEMORY” in “HDD SET UP” is set to other than “OFF”, as temporary
recording on HDD stops during recording on DVD.
About limitation on temporary recording
The temporary recording for Live Memory is canceled in the
● When the power is turned off
occurred
● When normal recording, timer recording, Live Memory Recording,
or Automatic Satellite Program Recording (੬ pg. 59) is performed
● When the “LIVE MEMORY” setting is changed (੬ pg. 82)
● When tuner channel setting is performed (੬ pg. 23)
● When dubbing is performed by pressing DUBBING (੬ pg. 70)
● When “DV” is selected by pressing CH +/– (੬ pg. 74)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
48
F 5
● Each press of the button during playback advances the playback
speed in 4 steps in the forward direction.
Buttons To Be Used During Live Memory Playback
● Turn on the unit.
Available only when paused
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD so that the HDD lamp lights up on the unit.
● Each press of the button advances the still picture frame by frame.
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed. Then, each press of the button advances
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
CABLE/DBS
G 8
● Pressing once during Live Memory Playback or Live Memory
Recording returns to the screen on air.
TV
DVD
HDD
● Pressing twice during recording stops recording and returns to the
screen on air.
H 9
Pressing once pauses playback (still picture playback). Pressing
repeatedly advances the still picture frame by frame.
A
I JUMP –
B
D
jumps back for the selected time interval and resumes playback.
(੬ pg. 49, “Jump Search”)
C
J JUMP +
Each press of the button during playback or Live Memory Playback
jumps forward for the selected time interval and resumes playback.
(੬ pg. 49, “Jump Search”)
E
G
F
H
I
J
K
L
K
Pressing once skips forward for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips forward continuously as many times as
pressed.
M
It is useful when skipping over unwanted sections.
L
Pressing once skips back for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
It is useful when watching sports programs, etc.
A LIVE
Returns to on air program screen. When a confirmation message
appears by pressing this button during timer programming or title
editing, etc., follow the instruction to return to the previous screen.
B NAVIGATION
Displays Library Database Navigation menu. You can choose a
title to play back.
C 2
● Pressing once skips back to the beginning of the chapter being
played back.
● Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
M LIVE CHECK
Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
Pressing successively clears the Live Check window and displays
only the picture currently being played back.
You can check, for example, if the program you are recording has
already finished.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed.
D 6
● Pressing once skips forward to the beginning of the next chapter
being played back.
● Pressing down for 2 or more seconds during playback advances
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed.
E 3
● Each press of the button during playback advances the playback
speed in 5 steps in the reverse direction.
Available only when paused
● Each press of the button reverses the still picture frame by frame.
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed. Then, each press of the button reverses
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON HDD DECK
EN
49
To Play Back The Previous Part Of The Channel
Currently Recording or Watching
You can play back the previous part of the channel you are
recording or watching (temporarily recorded on the background)
from the desired point. (੬ pg. 47, “Temporary recording for Live
Memory”)
1.5x Speed Search
You can play back a title quickly. (This feature can also be
performed with normal playback.)
1.5x speed search cannot be performed during recording on HDD
or DVD.
1 Press 3 to locate the point to start 1.5x speed search from.
2 Press 4 to resume playback.
1 Press 2 or 3 to locate the point to start playback from.
● Each press of 3 increases the reverse search speed.
3 Press 5 once.
● Pressing ON SCREEN displays “+X1.5” on the top right corner of the
2 Press 4 to start Live Memory Playback.
screen.
NOTE:
● The on-air screen resumes.
When the unit is connected with a digital audio device using an optional
optical cable, set “DIGITAL AUDIO OUT” to “PCM ONLY”. (੬ pg. 31)
NOTES:
● You can use various playback features during Live Memory
Playback. (੬ pg. 46)
Jump Search
● If you have started actual recording by pressing 7, pressing 8 in
step 3 only resumes the on-air screen. To stop actual recording,
press 8 again.
You can locate a scene ahead or behind the current one by
jumping scenes according to selected time intervals (੬ pg. 82)
during playback (or Live Memory Playback). This feature is also
available during recording (or Live Memory Recording) or when
watching a TV received program.
To Record From The Previous Part Of The Channel
Currently Watching (Live Memory Recording)
You can start recording from the previous part of the channel you
are currently watching (temporarily recorded on the background).
(੬ pg. 47, “Temporary recording for Live Memory”)
Press JUMP – or JUMP +.
● To advance forward or back, press JUMP – or JUMP + repeatedly
within 5 seconds of each press to continue jump.
● When you cannot advance any further (beginning or end of program
reached), the message “UNABLE TO GO BACK ANY MORE”
appears on the screen and the on-air screen resumes. In such a
case, press 2, 3 or 8.
1 Press 2 or 3 to locate the point to start recording from.
● Each press of 3 increases the reverse search speed.
2 Press 7 on the unit to start Live Memory Recording. Or while
holding 7, press 4 on the remote control.
Example 1:
Playback search when jump interval is set to 30 MIN jumps
3 Press 8 to stop Live Memory Recording.
Time counter
0 min
● The on-air screen resumes.
40 min
1 h 15 min
30 min
1 h
NOTES:
● You cannot use Live Memory Recording for channels other than the
channel you are currently watching.
● Recording speed is automatically set to SP mode when Live Memory
Recording is started.
● Temporarily recorded data prior to the beginning of Live Memory
Recording is erased when Live Memory Recording started.
Beginning of program
Current scene
End of program
To Move Back The Playback Position Slightly While
Recording (One Touch Replay Function)
You can move back the playback position while continuing to
record or timer record.
Example 2:
Recording search when jump interval is set to 15 MIN jumps
Clock time
9:00
9:40
9:45
10:15
Press
.
9:15
9:30
10:00
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds and
resumes pause.
To Resume Playback Of A TV Broadcast From The
Paused Point
Beginning of program
Current scene
End of program
You can resume playback of a TV broadcast you were recording or
watching from the point you have paused.
1 Press 9 to pause a TV broadcast.
● Recording continues when recording.
2 Press 4 to start Live Memory Playback.
● Playback resumes from the paused position.
3 Press 8 to resume the on-air screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON VHS DECK
EN
50
1 Load a cassette. Make sure the window side is up, the rear label
side is facing you and the arrow on the front of the cassette is
pointed toward the unit.
● Do not apply too much pressure when inserting.
● If the record safety tab has been removed, playback begins
automatically.
Basic Playback
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● The unit’s power comes on automatically and the counter is reset to
0:00:00.
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS
VHS/HDD/DVD
on the remote so that the VHS lamp lights up on the unit.
SELECT
4
5
3 Find the program start point. If the tape is advanced past the
start point, press 3. To go forward, press 5.
4 Press 4 to start playback.
5 Press 8 to stop playback.
● To eject the cassette, press x (VHS).
3
8
x
Clean the video heads using a dry cleaning cassette -
TCL-3F - when:
CABLE/DBS
TV DVD
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
● “USE CLEANING CASSETTE” appears on the screen (only with
“SUPERIMPOSE” set to “AUTO”). (੬ pg. 84)
VHS
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
Usable cassettes
4
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T-90
3
8
5
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be played on this
unit. Simply place the recorded cassette into a VHS Cassette
Adapter and it can be used just like any full-sized VHS
cassette.
** This unit can record on regular VHS and Super VHS
cassettes.
However, it will record regular VHS signals only.
• S-VHS recording is not possible with this unit.
● This unit is equipped with SQPB (S-VHS QUASI PLAYBACK) that
lets you watch tapes recorded in the S-VHS format and the SP
mode with regular VHS resolution.
• SQPB does not deliver Super VHS resolution.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON VHS DECK
EN
51
High-Speed Search
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
● Each press of the button increases the search speed for each
direction.
When pressing 5:
(SP): +5x{+7x
(EP): +11x{+21x
When pressing 3:
Playback Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS on
the remote so that the VHS lamp lights up on the unit.
Once 3 is pressed, reverse search starts in –1x normal playback
speed. After this process, each press of 3 changes the search
speed between –5x and –7x in SP mode, –11x and –21x in EP mode.
(SP): –1x]–5x{–7x
CABLE/DBS
TV
DVD
(EP): –1x]–11x{–21x
● To resume normal playback, press 4.
VHS
1
DVD
Quick Rewind A Little
During playback (or Live Memory Playback), press
CH+/-
. The unit
rewinds the picture a little (about 7 seconds) and resumes
playback.
● If the button is pressed repeatedly, the unit rewinds the pictures
continuously and resumes playback.
6
Skip Search
During playback, press
sections.
2
3
4
5
1 to 6 times to skip over unwanted
9
8
● Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
● To resume normal playback, press 4.
REC MODE
Index Search
AUDIO
PROGRESSIVE
SCAN
Your unit automatically marks
index codes at the beginning of
each recording. This function
gives you quick access to any one
of the 9 index codes in either
direction.
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of color.
● you cannot hear the sound.
NOTE:
Before starting, make sure the unit is
in the Stop mode.
Press 2 or 6 to activate Index Search. “INDEX –1” or “INDEX 1” is
displayed on the TV screen and search begins in the corresponding
direction.
● To access index codes 2 through 9, press 2 or 6 repeatedly
until the correct index number is displayed.
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
● If there is vertical jitter, press CH +/– to correct the picture.
2 Press 9 to activate frame-by-frame playback.
● To resume normal playback, press 4.
Example:
To locate the beginning of B from the current position, press 2
twice.
To locate the beginning of D from the current position, press 6
once.
Slow Motion
1 Press 9 to pause during playback.
Current position
2 Press and hold 9 for 2 seconds, then release. Press 9 and
release again to return to still picture.
● The speed changes for each direction by pressing 3 and 5
repeatedly.
● To resume normal playback, press 4.
NOTE:
During slow motion playback, some noise may appear on the TV
screen. Press CH + or – to eliminate the noises.
Index number
● When the specified index code is located, playback begins
automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON VHS DECK
EN
52
Next Function Memory
The Next Function Memory “tells” the unit what to do after
rewinding. Before continuing, make sure the unit is in the Stop
mode.
Soundtrack Selection
Your unit is capable of recording three soundtracks (HI-FI L, HI-FI
R and NORM) and will play back the one you select.
During Playback
For Automatic Start Of Playback
Press 3, then press 4 within 2 seconds.
Pressing AUDIO changes the soundtrack as follows:
TRACK
USE
Repeat Playback
Your unit can automatically play back the whole tape 100 times
repeatedly.
On-Screen Display
HI-FI
Hi-Fi sound is played back
HI-FI L
Sound on the left Hi-Fi channel is
played back
1 Press 4 to start playback.
2 Press and hold 4 for over 5 seconds, then release.
HI-FI R
NORM
Sound on the right Hi-Fi channel is
played back
●
lights up on the front display panel.
● After playing back a tape 100 times, the unit stops automatically.
Sound on the normal track is played
back
3 Press 8 at any time to stop Repeat Playback.
● Pressing 4, 3, 5 or 9 also stops Repeat Playback.
NORM
HI-FI
Both sounds on the Hi-Fi track and
normal track are mixed and played
Manual Tracking
Your unit is equipped with automatic tracking control. During
playback, you can override this and adjust the tracking manually by
pressing the CH buttons.
NOTES:
● “HI-FI” should normally be selected. In this mode, Hi-Fi stereo tapes
are played back in stereo, and the normal audio track is played back
automatically for tapes with only normal audio.
● “SUPERIMPOSE” must be set to “AUTO” or the on-screen displays
will not appear. (੬ pg. 84)
VHS Progressive Scan
You can watch the images on VHS deck in the Progressive scan
mode via component video.
1 During playback, press CH + or – on the unit simultaneously to
activate manual tracking.
2 Press CH + or – to adjust the tracking manually.
● To return to automatic tracking, press CH + or – simultaneously or
eject and insert the tape again.
ATTENTION:
Your TV needs to be compatible with Progressive and to have
Component video input connectors.
NOTE:
When a new tape is inserted, the unit enters the automatic tracking
mode automatically.
1 Set the Progressive-compatible TV to the component input
mode.
2 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
3 Press PROGRESSIVE SCAN for 3 or more seconds.
● The video output indicator
lights up on the front display panel.
4 Press VHS so that the VHS lamp lights up on the unit, then
press PROGRESSIVE SCAN.
● “COMP OFF” is displayed on the front display panel. It will be
displayed for 5 seconds.
5 Press PROGRESSIVE SCAN again within 5 seconds.
● “COMP ON” is displayed on the front display panel.
[COMPONENT VIDEO OUT (Y/P /P )] connectors.
B
R
NOTES:
● Be sure to engage the HDD or DVD deck in stop mode.
● To disengage the VHS Progressive Scan mode, perform steps 4 and
5 to switch to “COMP OFF”.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON VHS DECK
EN
53
Basic Recording
Recording Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS on
the remote so that the VHS lamp lights up on the unit.
VHS/HDD/DVD
SELECT
4 9
7
VHS/HDD/DVD
7
8
CH +/
VHS
REC
MODE
SELECT
CABLE/DBS
CABLE/DBS
TV DVD
TV
DVD
TV/VIDEO
VHS
0-9
CH+/-
CANCEL
CH+/-
4
9
7
8
DISPLAY
REC MODE
While recording is going on, you can watch another program on
the TV by using the TV’s tuner.
1 Load a cassette with the record safety tab intact.
● The unit’s power comes on automatically and the counter is reset to
0:00:00.
NOTE:
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS
It is required that the remote control is set to be able to operate the TV
on the remote so that the VHS lamp lights up on the unit.
in advance. (੬ pg. 78)
3 Press CH +/– or the number keys to select the channel you
1 During recording, press TV/VIDEO to select TV mode if your
unit is connected to the TV via the RF connection.
● VHS mode is disengaged, and the VIDEO indicator on the front
display panel lights off.
wish to record.
4 Press REC MODE repeatedly to set the recording mode.
5 Press 7 on the unit to start recording. Or while holding 7, press
VIDEO indicator lights off.
4 on the remote control.
● The VHS recording lamp lights up on the unit.
6 Press 9 to pause recording.
● You can select channel during the Record Pause mode.
● To resume recording, press 4.
7 Press 8 to stop recording.
● The program received on the TV’s tuner is displayed on the TV
screen.
● The VHS recording lamp lights off on the unit.
2 Slide the TV/CABLE/DBS/DVD switch to TV.
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording or timer recording (੬ pg. 54, 60, 61), the recording will
resume automatically when power is restored to the unit unless the
unit’s memory backup has expired.
3 Press CH +/– repeatedly to select the desired channel.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON VHS DECK
EN
54
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set “2ND
AUDIO RECORD” to “ON”. (੬ pg. 85)
1 Press 7 on the unit to start recording.
NOTE:
2 Press 7 again to engage the ITR mode.
When the channel is changed on the unit;
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● The “SAP” indicator appears on the screen for about 5 seconds if the
program is a SAP broadcast.
● Both indicators appear when a stereo program is accompanied by
SAP sound.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the 7 button on the unit.
● When the end of the tape is reached during timer recording or Instant
Timer Recording, the cassette is automatically ejected and the unit is
shut off.
Accidental erasure prevention
To prevent accidental recording on
a recorded cassette, remove its
safety tab. To record on it later,
cover the hole with adhesive tape.
● During Instant Timer Recording, any other timer programmed
recording won’t start even if their start time has come. In such a case,
the timer programmed recording starts (if the end time of the timer
programmed recording is set after the end of Instant Timer
Recording) after the Instant Timer Recording finishes.
Elapsed Recording Time Indication
1 Press DISPLAY until a counter reading appears on the front
display panel.
Record safety tab
2 Press CANCEL to reset the counter before starting recording or
playback.
● The counter is reset to “0:00:00” and shows the exact elapsed time
as the tape runs. You can check the exact time of a recording or
playback.
Tape Remaining Time
1 Press DISPLAY until the time remaining on the tape appears.
● By pressing the DISPLAY button, you can change display to show
the clock time, counter reading or tape remaining time.
NOTES:
● When you press DISPLAY, the on-screen display appears on the TV
screen for 5 seconds, then the displays other than the counter
disappears. To clear the counter display, press DISPLAY.
● Depending on the type of tape being used, the tape remaining time
reading may not appear right away, or is not correct.
“– –:– –” may sometimes appear, or the display may blink on
occasion.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
55
7 The PlusCode number you entered and the matching timer-
VCR Plus+ C3® Timer Programming
recording information are displayed on the TV screen. Check the
program data.
● To cancel this setting, press RETURN.
You can program this unit to timer-record as many as
32 programs.
IMPORTANT:
With the VCR Plus+ system, timer programming is greatly
simplified because each TV program has a corresponding code
number which your unit is able to recognize.
Make sure the channel position number you wish to record is
You can use the remote control to enter the PlusCode number.
8 Press rt to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “INPUT TITLE” (੬ pg. 64, “Modify Title Name”)
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● “CATEGORY” (੬ pg. 65, “Modify Category”)
● “WEEKLY/DAILY” (੬ pg. 56, “Weekly/Daily Recording”)
● “REC MODE” (੬ pg. 41, “Recording Mode”)
CABLE/DBS
9 Press rt to select “OK”, then press ENTER to access the
TV
DVD
Program Confirmation screen.
10Press w e to select “EXIT”, then press ENTER to complete
timer programming.
● To program another timer, press w e to select “CONTINUE”, then
press ENTER.
0 – 9
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 58.
PROGRAM
ENTER
NOTES:
● There may be cases that the VCR Plus+ Timer Programming
function prolongs the stop time of the programming.
● When two successive programs are recorded on a DVD-RW disc
with the VCR Plus+ Timer Programming function, the beginning of
the second one may be left off the recording.
RETURN
● If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programmed.
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the VCR Plus+ program screen in step 7. When this
happens, set the correct Guide Channel number for that station.
1 Load a recordable disc if recording to DVD.
Cable Box and DBS Receiver Users
2 Press PROGRAM to access the program top screen.
To timer-record a satellite broadcast using the VCR Plus+
system:
3 Press rtw e to select “VCR Plus+ PR.”, then press ENTER.
● When “PROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS” appears on the TV screen, you need to cancel some of
the reserved programs. (੬ pg. 58)
A Perform “Cable Box and/or DBS Receiver Control Setting
(HDD & DVD Deck only)” (੬ pg. 24).
B Perform “VCR Plus+ C3® Timer Programming” (੬ pg. 55).
C Leave the cable box or DBS receiver’s power on.
4 Press the number keys to
1
23 PROGRAM
>
VCR PLUS+ (1/2)
enter the VCR Plus+ number of a
program you wish to record.
OR
Press rtw e to select the
desired number key on the
screen, then press ENTER.
Repeat to enter all required
numbers.
PLUS CODE NO.
1 2 3 4
1
4
7
DELETE
2
5
8
0
3
6
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [PROGRAM]
TO EXIT
9
DELETE ALL
RECORD TO
DVD
CONFIRM
PROGRAM
EXIT
ENTER
SELECT
● If you have made a mistake, press rtw e to select “DELETE” or
“DELETE ALL’, then press ENTER and input the correct number
before you press ENTER again.
5 Press rt to select “RECORD TO”, then press ENTER. Press
rt to select the desired recording deck, then press ENTER.
6 Press rtw e to select “CONFIRM”, then press ENTER.
● If the number you entered is invalid, “PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY” appears on the TV
screen. Input a valid PlusCode number.
● If “GUIDE PROGRAM IS NOT SET SET GUIDE PROGRAM THEN
RETRY” appears on the TV screen, set Guide Channel Numbers
manually. (੬ pg. 86)
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
56
Weekly/Daily Recording
You can record programs with one of the following weekly/daily
timer settings.
For the HDD deck
When you select a mode other than ONCE, the space on the hard
disk drive is saved for new recordings by overwriting previous
recordings. To prevent loss of a needed recording, backup
programs you wish to save by dubbing them to DVD discs before
overwriting previous recordings. Or save the title of weekly/daily
programs to avoid overwriting of a previous week/day. (੬ pg. 58)
ONCE (One Time Recording)
In this mode a program will not be automatically overwritten.
WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program recorded
last week is automatically deleted and overwritten by the new
program. Save the title of each program you wish to save, then the
recorded program is saved and will not be overwritten by the new
program.
This week’s drama
Overwritten
Last week’s drama
MON–SUN (FOR A WEEK)/ MON–SAT (FOR A WEEK)/ MON–FRI
(FOR A WEEK) (Daily Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program recorded
on the same day last week is automatically deleted and overwritten
by the new program. Save the title of each program you wish to
save, then the recorded program is saved and will not be
overwritten by the new program.
This
week
MON TUE WED THU FRI
Overwritten
Last
MON TUE WED THU FRI
week
MON–SUN (OVERWRITE)/ MON–SAT (OVERWRITE)/ MON–FRI
(OVERWRITE) (Daily Recording/Daily Overwrite)
When the set daily program is broadcast, yesterday’s program is
automatically deleted and overwritten by the new program. Save
the title of each program you wish to save, then the recorded
program is saved and will not be overwritten by the new program.
Tuesday’s program
Overwritten
Monday’s program
For the DVD deck
ONCE (One Time Recording)
WEEKLY (Weekly Recording)
MON–SUN/ MON–SAT/ MON–FRI (Daily Recording)
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
57
8 Press rt to select “SOURCE”, then press ENTER. Press rt
to select the desired source, then press ENTER.
● To select the desired source, the respective settings must be set,
Manual Timer Programming
You can program this unit to timer-record as many as
32 programs.
9 Press rt to select “CH”, then press ENTER. Press rt to
If you do not know the VCR Plus+ number for the program you
wish to record, use the following procedure to set your unit to
timer-record the program.
select the desired channel.
10Press rt to select “CONFIRM”, then press ENTER.
11Set the other recording options as required.
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Refer to step 8 in “VCR Plus+ C3® Timer Programming” (੬ pg. 55).
12Press rt to select “OK”,
2
PROGRAM
>
CALENDAR PROG. (3/3)
then press ENTER to access the
01/08/03 WED 10:30PM
GARDENING
-
11:00PM DBS 100
[EDUCATION] FR360
1:00
28:00
Program Confirmation screen.
INPUT TITLE
CATEGORY
GARDENING
EDUCATION
SELECT WITH [
]
then press ENTER to complete
timer programming.
● To program another timer, press
w e to select “CONTINUE”, then
press ENTER.
THEN PRESS [ENTER]
CABLE/DBS
PRESS [PROGRAM]
TO EXIT
WEEKLY/DAILY
REC MODE
MON-FRI (FOR A WEEK)
FR360
TV
DVD
PROGRAM
EXIT
ENTER
O K
SELECT
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 58.
NOTES:
● When two successive programs are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
PROGRAM
ENTER
rtwe
Cable Box and DBS Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Cable Box and/or DBS Receiver Control Setting
(HDD & DVD Deck only)” (੬ pg. 24).
B Perform “Manual Timer Programming” (੬ pg. 57).
C Leave the cable box or DBS receiver’s power on.
Relief Recording
When a program that is set for the DVD deck cannot be
recorded properly, the program is recorded to the HDD deck
instead in XP mode.
● If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining capacity
of the DVD disc lasts.
1 Load a recordable disc if recording to DVD.
2 Press PROGRAM to access the program top screen.
3 Press rtw e to select “CALENDAR PR.”, then press ENTER.
● When “PROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS” appears on the TV screen, you need to cancel some of
the reserved programs. (੬ pg. 58)
● If “JUST” is selected for the recording mode, the current recording
mode for the DVD deck is applied.
4 Press rtw e to select the desired date, then press ENTER.
5 Press rt to select “RECORD
2
PROGRAM CALENDAR PROG. (2/3)
>
Source Selection
TO”, then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
01/08/03 WED 10:30PM
-
11:00PM DBS 100
[MISC.
To select the desired source (TV, CATV, DBS or AUX), the
respective settings must be set as follows:
and the “BAND” setting on the “MANUAL CH SET” set to “TV”
(੬ pg. 23).
]
XP
RECORD TO
START
STOP
HDD
SELECT WITH [
]
THEN PRESS [ENTER]
10:30PM
11:00PM
DBS
PRESS [PROGRAM]
TO EXIT
SOURCE
CH
6 Press rt to select “START”,
then press ENTER. Press rt to
set the desired start time, then
press ENTER.
100
PROGRAM
EXIT
ENTER
O K
SELECT
“CATV”: The “CABLE BOX OUTPUT CHANNEL” setting on the
“CABLE SET UP” screen must be set to other than “OFF”
(੬ pg. 24), or the “BAND” setting on the “MANUAL CH SET”
set to “CATV” (੬ pg. 23).
“DBS”: The “DBS SET UP” setting on the “STB SET” screen
must be set to other than “OFF” (੬ pg. 24).
“AUX”: Always selectable.
● Each press of rt increases/decreases the start time in 1-minute
interval.
● To increase/decrease the start time in 30-minutes interval, press and
hold rt.
7 Press rt to select “STOP”, then press ENTER. Press rt to
set the desired stop time, then press ENTER.
● Each press of rt increases/decreases the stop time in 1-minute
interval.
● To increase/decrease the stop time in 30-minutes interval, press and
hold rt.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
58
When Programs Overlap Each Other
CABLE/DBS
TV
DVD
If “PROGRAM OVERLAPPED” appears, you have other programs
overlapping the program you have just made.
Confirm with the arrow on “MODIFY”, then press ENTER. Program
Overlap list appears.
Example: Five programs
overlap each other.
2
PROGRAM
>
CALENDAR PROG. (OVERLAP)
01/08/03 WED 10:30PM
GARDENING
-
12:00AM DBS 100
[EDUCATION] FR360
5 PROGRAM OVERLAPPED
1 Confirm the overlapping
programs. Overlapping programs
appear on the TV screen.
SELECT PROGRAM TO MODIFY
SELECT WITH [
]
PROGRAM
THEN PRESS [ENTER]
10:30PM- DBS 100
PRESS [PROGRAM]
TO EXIT
D
W
D
9:00PM-
9:30PM- DBS 210
10:00PM- TV 63
11:00PM- CATV
L-1
ENTER
rtwe
NOTE:
PROGRAM
EXIT
ENTER
4
If you do not mind this overlap,
press PROGRAM to finish the timer
program setting. The program with
SELECT
the lower program number will be recorded and the other one will not
be recorded correctly. If no changes are made for approximately 1
minute, the unit will return to the normal screen.
2 Press rt to select the desired program to be canceled or
changed, then press ENTER.
3 Perform “Cancel And Change Programs” (refer to left column).
NOTE:
When any overlaps remain after deletion and modification of programs,
Program Overlap list remains showing the conflicting programs. In such
a case, repeat the procedure above until the conflict is solved.
Check Programs
To check the whole list of programs
1 Press PROGRAM to access the program top screen.
2 Press rtw e to select “PROGRAM LIST”, then press ENTER.
● The details of a selected program appear on the top of the screen.
● The daily program of a title is listed as one program.
To check the list of programs by date
1 Press PROGRAM to access the program top screen.
ENTER.
3 Press rt to select the desired date, then press ENTER.
Cancel And Change Programs
● Repeat steps in “Check Programs” to select a program before
proceeding.
To cancel the program
To modify the program settings
1 Press rtw e to select “MODIFY”, then press ENTER.
2 Change the settings of the desired recording options as
required.
● Refer to steps 4 – 13 in “Manual Timer Programming” (੬ pg. 57).
To skip the weekly/daily programs to the next week/day
It is easy to temporarily cancel weekly/daily programs of a week/
day.
1 Press rtw e to select “PROGRAM SKIP”, then press ENTER.
2 Press w e to select “SKIP”, then press ENTER.
To save the titles of weekly/daily programs (HDD Deck Only)
Use this function to avoid overwriting titles of weekly/daily
programs of a previous week/day.
1 Press rtw e to select “TITLE SAVE”, then press ENTER.
2 Press w e to select “SAVE”, then press ENTER.
NOTE:
This function is available only when the remaining capacity of the hard
disc is sufficient.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON HDD/DVD DECK
EN
59
● Make sure the DBS receiver is connected to the unit’s [S-VIDEO/
VIDEO/AUDIO INPUT L-1] connectors.
● Program the timer on the DBS receiver.
Automatic Satellite Program Recording
(HDD Deck Only)
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Press HDD on the remote to choose the recording deck. You
can also press VHS/HDD/DVD SELECT on the unit repeatedly to
select the recording deck.
This function allows you to automatically record a satellite program
which is timer-programmed on your external DBS receiver.
Connect a DBS receiver to the unit’s [S-VIDEO/VIDEO/AUDIO
INPUT L-1] connectors and program the timer on the DBS
receiver. The unit starts or stops recording by the signals input
from the DBS receiver. After recording, the unit’s power shuts off
automatically.
2 Press REC MODE repeatedly to set the recording mode.
3 Press and hold REC LINK for about 2 seconds to engage the
Automatic Satellite Program Recording mode. “ ” and “R-LK”
appear on the front display panel.
● You can also connect the cable box if it has a timer.
NOTES:
press REC LINK.
ATTENTION:
● Be sure not to turn on the DBS receiver before the program is
executed; otherwise, the unit will start recording when the DBS
receiver’s power is turned on.
● If the unit’s power is off, it is not possible to engage the Automatic
Satellite Program Recording mode.
● In step 3, if “ ” blinks quickly on the front display panel even though
your DBS receiver’s power is off, Automatic Satellite Program
Recording will not work properly with that DBS receiver*. If this is the
case, perform “Manual Timer Programming” (੬ pg. 57) to
timer-record a satellite program.
* Some DBS receivers output signals even if the power is off. Automatic
Satellite Program Recording is not possible with those DBS receivers.
● “ ” blinks on the front display panel while Automatic Satellite
Program Recording is in progress.
● If you have connected another appliance other than a DBS
receiver to the [S-VIDEO/VIDEO/AUDIO INPUT L-1] connectors,
be sure not to engage the Automatic Satellite Program Recording
mode; otherwise, the unit will start recording when the connected
appliance’s power is turned on.
● Automatic Satellite Program Recording and timer-recording cannot
be done at the same time.
VHS/HDD/DVD
SELECT
● For timer programming of the DBS receiver, refer to the instruction
manual of the DBS receiver.
● Automatic Satellite Program Recording is not possible if your DBS
receiver does not have a timer.
● Pressing the unit’s 1 button while Automatic Satellite Program
Recording is in progress turns off the unit’s power and disengages
the Automatic Satellite Program Recording mode.
● If there are more than one satellite programs you wish to record with
Automatic Satellite Program Recording, it is not possible to set
different recording modes for each program.
● Depending on the type of DBS receiver, the unit may not record a
slight portion of the beginning of the program or may record slightly
longer than the actual length of the program.
REC MODE
CABLE/DBS
TV
DVD
HDD
● If you engage the Automatic Satellite Program Recording mode when
the DBS receiver’s power is on, the unit will not start Automatic
Satellite Program Recording even though “ ” blinks on the front
display panel. When the DBS receiver shuts off once and is turned
back on again, the unit starts recording.
● You can also record a program from your cable system in the same
way if the system has a timer.
REC MODE
REC LINK
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON VHS DECK
EN
60
7 Press REC MODE to select the desired recording mode.
VCR Plus+® Timer Programming
8 Press ENTER to complete timer programming.
● To program another timer, repeat steps 3-8.
● If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears
on the TV screen, see page 62.
You can program this unit to timer-record as many as 8 programs.
With the VCR Plus+ system, timer programming is greatly
simplified because each TV program has a corresponding code
number which your unit is able to recognize.
9 Press VHS TIMER to engage the unit’s timer mode. The VHS
recording lamp lights up on the unit and the HDD or DVD deck is
automatically selected. When the HDD or DVD deck is in timer
standby mode, the unit is automatically turned off.
You can use the remote control to enter the PlusCode number.
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● To disengage the timer mode, press VHS TIMER again.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
happens, set the correct Guide Channel number for that station.
CABLE/DBS
TV
DVD
VHS TIMER
VHS
(੬ pg. 86, “Changing VCR Plus+® Setting”)
0-9
NOTES:
● To Timer-Record Weekly Or Daily Serials:
— in step 6, press number key “9” for weekly serials or number key
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
you try to program the unit to record a ninth, “PROGRAM FULL”
appears on the TV screen and “FULL” appears on the front display
panel. To record the extra program, you must first cancel any
unnecessary programs. (੬ pg. 62)
CANCEL
PROGRAM
ENTER
rt
● To record the programs received by cable box or DBS receiver,
record on the HDD or the DVD discs. For details, refer to “VCR Plus+
C3® Timer Programming” (੬ pg. 55).
REC MODE
1 Load a cassette with the record safety tab intact.
2 Press VHS so that the VHS lamp lights up on the unit.
3 Press PROGRAM to access the
PROGRAM
Program screen.
VCR PLUS+ PRGM
PROGRAM / CONFIRM
4 Press rt to select “VCR
PLUS+ PRGM”, then press
ENTER.
R,T THEN (ENTER)
(PROGRAM) TO END
5 Press the number keys to enter
PLUSCODE NO.
the PlusCode number of a program
you wish to record, then press
ENTER.
● If you have made a mistake, press
CANCEL and input the correct
number before you press ENTER.
● If the number you entered is invalid,
“ERROR” appears on the TV
PRESS NUMBER KEY (0–9)
PRESS (PROGRAM) TO END
VCR PLUS+ SYSTEM
screen and “Err” appears on the front display panel.
Press CANCEL and input a valid PlusCode number.
6 The PlusCode number you
PROGRAM 1
entered and the matching timer-
recording information are displayed
on the TV screen. Check the
program data.
(PLUSCODE NO. 12345678)
START
12:00 AM
DATE
STOP
1:00 AM
CH SP/EP
1/ 30/04
15
SP
● To cancel this setting, press
PROGRAM.
R/T, REC MODE), THEN (ENTER)
(PROGRAM) TO END
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “Changing VCR Plus+® Setting” (੬ pg. 86) and
set the Guide Channel number correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON VHS DECK
EN
61
7 Press w e to select “STOP”, then press rt to set the desired
stop time.
Manual Timer Programming
● Each press of rt increases/decreases the stop time in 1-minute
interval.
● To increase/decrease the stop time in 30-minutes interval, press and
hold rt.
You can program this unit to timer-record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to timer-
record the program.
8 Press w e to select “DATE”, then press rt to set the desired
date.
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● The current date appears on the TV screen. The date you enter
appears in its place.
9 Press w e to select “CH”, then press rt to select the desired
channel.
10 Press REC MODE to select the desired recording mode. Or
press w e to select “SP/EP”, then press rt to select the desired
recording mode.
CABLE/DBS
TV
DVD
VHS TIMER
VHS
12 Press PROGRAM to complete timer programming.
“PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears. If “PROGRAM NOT
COMPLETED PROGRAM OVERLAP” appears on the TV screen,
see page 62.
0-9
PROGRAM
● To program another timer, repeat steps 3 - 12.
13Press VHS TIMER to engage the unit’s timer mode. The VHS
automatically selected. When the HDD or DVD deck is in timer
standby mode, the unit is automatically turned off.
rtwe
ENTER
● To disengage the timer mode, press VHS TIMER again.
NOTES:
● To Timer-Record Weekly Or Daily Serials:
weekly serials or number key “8” for daily serials (Monday - Friday).
Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
● You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, “PROGRAM FULL”
first cancel any unnecessary programs. (੬ pg. 62)
● In case of a power failure after programming, the unit’s memory
backup keeps your selections for approximately 5 seconds.
● Programs that start after midnight must have the next day’s date.
● To record the programs received by cable box or DBS receiver,
record on the HDD or the DVD discs. For details, refer to “Manual
Timer Programming” (੬ pg. 57).
REC MODE
1 Load a cassette with the record safety tab intact.
2 Press VHS so that the VHS lamp lights up on the unit.
3 Press PROGRAM to access the Program screen.
4 Press rt to select “PROGRAM/
PROGRAM
CONFIRM”, then press ENTER
VCR PLUS+ PRGM
PROGRAM / CONFIRM
access the Program Check screen.
R,T THEN (ENTER)
(PROGRAM) TO END
5 Press rt to select the blank
PR START STOP CH DATE
number, then press ENTER. The
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
program screen appears.
11:30P
1:00 125 12/25
(PROGRAM) TO END
6 Press w e to select “START”,
then press rt to set the desired
start time.
● Each press of rt increases/
decreases the start time in 1-minute
interval.
● To increase/decrease the start time in
30-minutes interval, press and hold
rt.
PROGRAM 4
START
– –:– –AM
DATE
STOP
– –:– –AM
CH SP/EP
– – – SP
– –/– –/– –
PRESS (RTYU, 8=DAILY
9=WEEKLY), THEN (ENTER)
(PROGRAM) TO END
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING ON VHS DECK
EN
62
When Programs Overlap Each Other
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program you
have just made.
CABLE/DBS
TV DVD
VHS TIMER
VHS
1
The Program Check screen appears and conflicting programs will
start blinking.
PR START STOP CH DATE
CANCEL
ENTER
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
PROGRAM
11:30P
1:00 125 12/25
9:00P 10:00 10 12/24
rtwe
(
)](ENTER) (PROGRAM) : END
Example: Program 1 (you have just made) and Program 4
overlap each other.
1 Confirm the overlapping programs. Overlapping programs blink
on the TV screen.
2 Press rt to select the program to modify, then press ENTER
or e.
● You can only select one of the overlapping programs.
NOTE:
If you do not mind this overlap, press PROGRAM to finish the timer
program setting. The program with the lower program number will be
recorded and the other one will not be recorded correctly. If no changes
are made for approximately 1 minute, the unit will return to the normal
screen.
Check, Cancel And Change Programs
1 When the VHS recording lamp (7) lights up on the unit
Press VHS TIMER, then press DVD (1).
3 Press rt to select the desired program to be canceled or
When the VHS lamp does not light up on the unit
Press VHS so that the VHS lamp lights up on the unit.
changed.
To cancel the program
Press CANCEL.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
2 Press PROGRAM to access the
PR START STOP CH DATE
Program screen.
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
11:30P
3 Press rt to select “PROGRAM/
CONFIRM”, then press ENTER to
access the Program Check screen.
1:00 125 12/25
To change the program setting
Press ENTER, then go to step 4.
4 Change the program setting.
(PROGRAM) TO END
● Refer to steps 6 - 11 in “Manual Timer Programming” (੬ pg. 61).
5 Press PROGRAM to access the Program screen, then press
rt to select “PROGRAM/CONFIRM” to check if the conflict has
been settled.
Program check screen appears.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
4 Press rt to select the program,
then press ENTER. The program
screen appears.
PROGRAM 4
START
8:00AM
DATE
STOP
10:00AM
CH SP/EP
12/24/04
FRI
12
SP
To cancel a program
Press CANCEL.
PRESS (CANCEL) TO CANCEL
PRESS (ENTER) TO CONFIRM
(PROGRAM) TO END
NOTE:
When any overlaps remain after deletion and modification of programs,
Program Check screen remains showing the conflicting programs. In
such a case, repeat the procedure above until the conflict is solved.
5 Change the settings of the desired recording options as
required.
● Refer to steps 6 - 11 in “Manual Timer Programming” (੬ pg. 61).
6 Press PROGRAM to complete timer correction. The previous
screen resumes.
7 Press VHS TIMER.
● The VHS recording lamp lights up on the unit and the HDD or DVD
deck is automatically selected. When the HDD or DVD deck is in
timer standby mode, the unit is automatically turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
63
Using Library Database Navigation system, you can easily modify
registered information, edit the title or play list, as well as search
for the beginning of each title.
Library Database Navigation
About registration of information
The following information is automatically registered for each title
when ordinary recording or timer recording is performed, then
stored in an area specified on the unit.
● index* (reduced pictures to show program titles)
● program title*
● category*
● date and time
● channel
● recording mode
The Library Database Navigation enables you to search and select
the desired titles recorded on the HDD deck and the DVD deck
very easily.
You can record up to 99 titles on a disc.
Each time a title is recorded, the information of the title is
registered for the Library Database Navigation automatically.
So, you can confirm the information of the titles recorded with the
Library Database Navigation screen. And, you can also select one
of the titles recorded using the Library Database Navigation.
● length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database
Navigation system.
The following screen appears as the Library Database Navigation
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing rt w e on
the remote control.
The limitations of registration
You can register information up to 99 titles for the DVD deck and
200 titles for the HDD deck.
When the amount of information is at the limits of registration, you
cannot record new titles any more. In this case, you need to delete
old titles to register new one. (੬ pg. 65)
NAVIGATION > ORIGINAL
0026 [FISH WORLD
]
143 MIN
A
25/12/03 THU 10:00
FROG WORLD
-
10:15
PR.
3
D
E
[HOBBY] EP
NOTES:
SELECT WITH [
]
THEN PRESS [ENTER]
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
PRESS [NAVIGATION]
TO EXIT
B
C
NAVIGATION
EXIT
ENTER
● When you move the title recorded on HDD to DVD, the icon will be
SELECT
changed to
.
F
G
● Sound of received channel may be interrupted while the Library
Database Navigation screen is displayed.
● The order of index which are displayed by pressing DUBBING differs
from the images displayed by pressing NAVIGATION or EDIT.
● You cannot perform timer recording during editing of thumbnail
images or play lists by pressing EDIT. Press EDIT to clear the Editing
screen before performing timer recording.
A Playback screen
(Indicates currently received TV program.)
B Guidance for operations
C Scroll bar
(Appears when there are over nine registered titles (or play
lists). The scroll bar only indicates that there are more titles (or
play lists) hidden off the current screen display. To show hidden
titles (or play lists), press rt w e repeatedly.)
D Recording information for the title indicated by the arrow
E Index list
(Thumbnail still of each title)
Thumbnail still is not to be played back.
F Index
:
:
:
Indicates no index is registered.
Indicates title in standby for timer recording.
Indicates no title is registered.
G Icons
(Indicate the record condition of each title.)
The Icons and their meanings
This title is write-protected.
This title was recorded with timer recording.
This title is Weekly Recording/Weekly Overwrite.
This title is Daily Recording/Daily Overwrite.
This title is Daily Recording/Weekly Overwrite.
This title has not been played back.
W
D
D
NEW
This title is copy-protected.
This title can only be recorded once (copy-once
title).
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
64
Scan For Beginning Of Title
Modify Original Information
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to scan.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to modify.
CABLE/DBS
TV
DVD
HDD
DVD
ATTENTION:
● It is not possible to modify discs recorded on DVD units from other
manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
CANCEL
ENTER
MEMO
NAVIGATION
rtwe
Modify Index
1 Press EDIT. The Editing screen appears.
4
9
2 (DVD deck only) Press rt w e to select “MODIFY” under
8
“ORIGINAL/PLAY LIST”, then press ENTER.
3 Press rt w e to select “MODIFY” under “ORIGINAL”, then
press ENTER.
4 Press rt w e to select one title you want to modify, then press
ENTER.
5 Press w e to select “INDEX”.
6 Search for the picture from the
EDITING > MODIFY INDEX
12/26/02 THU 10:00AM
FROG WORLD
-
10:15AM
TV
3
S
title by pressing the appropriate
buttons (3, 4, 5, or 9). The
pictures of the title appear on the
left window.
[OTHERS] SP
INDEX
You can scan the beginning of the title easily with the Library
Database Navigation.
1 Press NAVIGATION. The Library Database Navigation screen
PROG.
1
0 : 01 : 03
appears.
7 Confirm the arrow is on
SELECT IMAGE TO REPLACE WITH
ON REMOTE
RETURN
“REPLACE”, then press ENTER
to register new index. New index
appears on the right window.
REPLACE
2 Press rt w e to select “ORIGINAL”, then press ENTER.
3 Press rt w e to select the
NAVIGATION > ORIGINAL
0026 [FISH WORLD
12/26/02 THU 10:00AM
FROG WORLD
]
143 MIN
TV
[HOBBY] EP
index (small pictures) of the
desired title, then press ENTER.
● When you want the plural titles to
be played back continuously,
-
10:15AM
3
S
to the previous screen.
SELECT WITH [
THEN PRESS [ENTER]
]
8 Press EDIT to return to the normal screen.
PRESS [NAVIGATION]
TO EXIT
press MEMO after selecting the
desired title. The numbers of the
playback order appear on the
index. You can select up to 8 titles.
● When you want to correct the
Modify Title Name
NAVIGATION
EXIT
ENTER
SELECT
1 Perform steps 1 – 4 of “Modify Index” (੬ pg. 64) before
continuing.
order, move the arrow to the desired index and press MEMO. The
number disappears and the unit re-numbers the other programs
automatically.
2 Press rt w e to select “NAME”, then press ENTER.
3 Press rt w e to select the
A
BC EDITING > MODIFY NAME
0026 [FISH WORLD
12/26/02 THU 10:00AM
FROG WORLD
]
64 MIN
desired letter or command, then
press ENTER. Repeat this
process to complete the name.
● To correct a letter, press rt w e
to select “DELETE”, then press
ENTER.
● When you want to cancel the order, press CANCEL (&).
-
10:15AM
TV
3
S
[HOBBY] XP
F ROG
W
OR L D
4 Press w e to select
NAVIGATION > ORIGINAL
SELECT WITH [
THEN PRESS [ENTER]
]
A
G
M
S
B
H
N
T
C
I
D
J
E
K
F
L
R
X
a
g
b
c
i
d
j
e
k
f
l
1
4
7
0
*
2
5
8
+
/
3
6
9
-
“BEGINNING”, then press ENTER.
12/26/02 THU
10:00AM 10:15AM TV
SP
h
n
t
S
-
3
PRESS [EDIT]
TO EXIT
O
U
P
V
Q
W
m
s
o
u
p
v
q
w
r
x
● To resume playback from the point
where playback was previously
stopped, press w e to select
“RESUME”, then press ENTER.
● To repeat playback of a selected
title, press w e to select
FROG WORLD
[HOBBY]
Y
Z
y
z
=
SELECT WITH [
THEN PRESS [ENTER]
]
!
'
"
#
)
$
,
%
.
&
:
;
\
<
]
>
^
?
_
@
`
[
{
|
}
~
(
EDIT
EXIT
ENTER
SELECT HOW TO PLAY BACK
PRESS [NAVIGATION]
TO EXIT
CANCEL
DELETE
SAVE
BEGINNING
RESUME
REPEAT
● You can enter the letters up to 64.
SELECT
4 Press rt w e to select
NAVIGATION
EXIT
ENTER
“SAVE”, then press ENTER.
SELECT
“REPEAT”, then press ENTER.
5 Press EDIT to return to the normal screen.
5 Press 9 to pause playback.
● To resume normal playback, press 4.
6 Press 8 to stop playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
65
Modify Category
Delete Unwanted Part Of The Title (DVD deck only)
You can delete unwanted part of the title.
1 Perform steps 1 – 4 of “Modify Index” (੬ pg. 64) before
continuing.
1 Perform steps 1 – 3 of “Modify Index” (੬ pg. 64) before
continuing.
2 Press rt w e to select “CATEGORY”, then press ENTER.
2 Press rt w e to select “DEL SCENE”, then press ENTER.
3 Press rt w e to select the
EDITING > MODIFY CATEGORY
0026 [FISH WORLD
12/26/02 THU 10:00AM
FROG WORLD
]
64 MIN
desired category, then press
3 Press rt w e to select one title whose unwanted part you
S
-
10:15AM
TV
3
[HOBBY] XP
ENTER.
want to delete, then press ENTER.
MOVIE
MUSIC
DRAMA
SELECT WITH [
]
4 Press EDIT to return to the
THEN PRESS [ENTER]
4 The playback pictures appear in the window on the screen. The
ANIMATION
NEWS
SPORTS
DOCUMENTARY
EDUCATION
PRESS [EDIT]
TO EXIT
normal screen.
elapsed playing time starts counting with the arrow on “IN”.
WEATHER
5 Find the point where you want
EDITING > ORIGINAL/DELETE SCENE
EDIT
EXIT
ENTER
HOBBY
ENTERTAINMENT ART
12/22/02 SUN 5:30AM
RALLY CAR
-
8:00AM
TV 12
S
the deletion to begin, then press
ENTER with the arrow on “IN”.
The edit-in time is fixed and the
elapsed playing time starts
counting again.
SELECT
[OTHERS] SP
IN
0 : 05 :15
Protect Title (DVD deck only)
OUT
0 : 06 :15
You can protect titles to prevent accidental erasure of the
important titles.
PROG.
1
0 : 01 : 03
SELECT IMAGE TO REPLACE WITH
ON REMOTE
6 Find the point where you want
the deletion to end, then press
ENTER with the arrow on “OUT”.
The edit-out time is fixed.
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
IN OUT
PREVIEW
OK
1 Perform steps 1 – 3 of “Modify Index” (੬ pg. 64) before
continuing.
2 Press rt w e to select “PROTECT”, then press ENTER.
3 Press rt w e to select a title you want to protect, then press
ENTER.
4 Press w e to select “PROTECT”, then press ENTER. “
appears.
● To cancel the protection, repeat 3 – 4 again. In step 4, select
“CANCEL PROTECT”, then press ENTER.
”
the edited title.
8 Press w e to select “OK”, then press ENTER.
● If you do not want to delete the scene, press EDIT or RETURN.
To modify the points
A Press EDIT or RETURN.
B Repeat steps 4 – 8 as necessary.
5 Press EDIT to return to the normal screen.
NOTE:
All the titles on a disc will be deleted once the disc is formatted even if
they are protected titles. (੬ pg. 65)
9 Press w e to select “DELETE”, then press ENTER. The
selected scene is deleted.
● To cancel the deletion, press w e to select “CANCEL”, then press
ENTER.
Delete Title
You cannot record any more with Library Database Navigation
once the registered titles on the disc reach 99 titles for the DVD
deck and 200 titles for the HDD deck. Deleting unnecessary titles
after dubbing or other operations can increase remaining time and
available recording capacity. (For DVD-R discs, although it is
possible to delete recorded titles, available recording capacity
does not increase.) The deleted title is never resumed. Play lists
and title information in the unit’s library are also deleted.
10Press EDIT to return to the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● Available recording capacity may not match the deleted part after
deletion.
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “DELETE” under “ORIGINAL”, then
press ENTER.
3 Press rt w e to select one title you want to delete, then press
ENTER.
4 Press w e to select “DELETE”, then press ENTER.
● When you cancel the deletion, select “CANCEL”, then press ENTER.
5 Press EDIT to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
66
Divide Title (HDD deck only)
Modify Play List Information
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “DIVIDE”, then press ENTER.
3 Press rt w e to select a title to divide, then press ENTER.
4 Press 4, and press 3 or 5 to locate a point to divide, then
press 9.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to modify.
5 Confirm the arrow is on “DIVIDE”, then press ENTER at the
dividing point.
● The first picture (start) of the newly created title appears in the
bottom right window.
6 Press w e to select “PREVIEW”, then press ENTER.
● The first several seconds of the newly created title is played back,
then the playback pauses at the dividing point.
● To undo the division, press w e to select “RETRY”, then press
ENTER. Repeat the above procedure to locate another point to
divide.
ATTENTION:
● It is not possible to modify discs recorded on DVD units from other
manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
7 Press w e to select “OK”, then press ENTER.
8 Press EDIT to return to the normal screen.
CABLE/DBS
TV
DVD
NOTE:
There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
HDD
DVD
Modify Chapter
You can create and delete chapter marks in titles.
CANCEL
ENTER
MEMO
1 Perform steps 1 – 4 of “Modify Index” (੬ pg. 64) before
EDIT
continuing.
NAVIGATION
2 Press rt w e to select “CHAPTER”, then press ENTER.
rtwe
3 Confirm the arrow is on
EDITING > MODIFY CHAPTER
“MARK”, then press ENTER at
6
4
5
CHAPTER 03/10
2
3
positions you want to mark.
● The newly created chapter is
0 : 07 : 01
displayed.
● To undo the marking, press w e
9
8
01 00 : 00 : 00
02 00 : 05 : 30
03 00 : 07 : 00
04 00 : 30 : 00
to select “RETRY”, then press
ENTER. Repeat the above
procedure to locate another point
to mark.
MARK
ERASE
RETRY
RETURN
4 Press 4, and press 3 or 5 to select one chapter you want
to delete, then press 9.
5 Press w e to select “ERASE”, then press ENTER.
● The selected chapter is deleted.
● To undo the deletion, press w e to select “RETRY”, then press
ENTER. Repeat the above procedure to locate another point to
delete.
Play List
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a disc (which allows video data to be
instantly read no matter where it is on the disc), a play list includes
information such as the timer counter for the playback start point
and end point, indexes for checking the contents of recorded data,
category information, and more. Playback according to a play list
you have created allows you to enjoy various combinations of
video images from a single title.
6 Press EDIT to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
67
Create Play List
Add scenes
1 Press EDIT. The Editing screen appears.
1 Perform steps 1 – 4 in “Edit Scenes” (੬ pg. 67) before
continuing.
2 (DVD deck only) Press rt w e to select “MODIFY” under
“ORIGINAL/PLAY LIST”, then press ENTER.
2 Press rt w e to select “SEL. TITLE”, then press ENTER.
3 Perform steps 4 – 10 in “Create Play List” (੬ pg. 67).
3 Press rt w e to select “CREATE”, then press ENTER.
4 Press rt w e to select a title that includes scenes to be
Move Scenes
included in a play list, then press ENTER.
5 The playback pictures appear in the window on the screen. The
1 Perform steps 1 – 4 of “Edit Scenes” (੬ pg. 67) before
elapsed playing time starts counting with the arrow on “IN/OUT”.
continuing.
6 Find the point where you want
EDITING > PLAY LIST/CREATE
TOTAL
00 : 00 : 00
PAGE 1 / 1
3 Press rt to select a scene to move, then press ENTER.
SCENE
the created play list to begin, then
press ENTER with the arrow on
“IN/OUT”. The edit-in time is fixed
and the elapsed playing time
starts counting again.
1
2
3
4
5
6
7
8
PRO.
1
4 Press rt to select another scene to which the scene is to be
PRO.
1
0 : 00 :15
moved, then press ENTER.
ENTER.
IN
TO
IN/OUT
SEL. TITLE
MODIFY
DELETE
MOVE
PREVIEW
OK
7 Find the point where you want
the created play list to end, then
press ENTER with the arrow on
“IN/OUT”. The edit-out time is fixed.
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
RETRY
5 Perform steps 8 – 10 in “Create Play List” (੬ pg. 67).
Delete Scenes
1 Perform steps 1 – 4 of “Create Play List” (੬ pg. 67) before
● The edit-out point must come after the edit-in point.
continuing.
2 Press rt w e to select “DELETE”, then press ENTER.
3 Press rt to select a scene to delete, then press ENTER.
4 Perform steps 8 – 10 in “Create Play List” (੬ pg. 67).
preview the play list.
9 Press rt w e to select “OK”, then press ENTER. The play list
is created.
To modify the points
A Press w e to select “MODIFY”, then press ENTER.
B Repeat steps 5 – 9 as necessary.
Play Back Play List
1 Press NAVIGATION. The Library Database Navigation screen
appears.
normal screen.
2 Press rt w e to select “PLAY LIST”, then press ENTER.
3 Press rt w e to select the
NOTES:
NAVIGATION > PLAY LIST
0026 [FISH WORLD
026 CREATED 26/12/03 FRI
TEDDY BEAR 25/12
]
143 MIN
index (small pictures) of the
desired play list, then press
ENTER.
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● The title, index and category of the play list can be modified in the
same way as “ORIGINAL”. (੬ pg. 64)
[MOVIE]
003
001
004
007
002
005
008
SELECT WITH [
THEN PRESS [ENTER]
]
● When you want the plural play lists
to be played back continuously,
press MEMO after selecting the
desired play lists. The numbers of
the playback order appear on the
006
009
PRESS [NAVIGATION]
TO EXIT
● You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest edition,
etc.
NAVIGATION
EXIT
ENTER
SELECT
index. You can select up to 30 play lists.
Edit Scenes
● When you want to correct the order, move the arrow to the desired
index and press MEMO. The number disappears and the unit re-
numbers the other play lists automatically.
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
● When you want to cancel the order, press CANCEL (&).
“ORIGINAL/PLAY LIST”, then press ENTER.
4 Press w e to select “BEGINNING”, then press ENTER. The
press ENTER.
playback starts.
5 Press 9 to pause playback.
4 Press rt w e to select a play list to modify, then press
● To resume normal playback, press 4.
ENTER.
6 Press 8 to stop playback.
5 Press rt w e to select “SCENE”, then press ENTER.
6 Press rt w e to select “MODIFY”, then press ENTER.
7 Press rt w e to select a scene to modify, then press ENTER.
8 Perform steps 5 – 10 in “Create Play List” (੬ pg. 67).
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
68
Delete Play List
Modify Library Information
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
“ORIGINAL/PLAY LIST”, then press ENTER.
3 Press rt w e to select “DELETE” under “PLAY LIST”, then
press ENTER.
Title information can be registered in the unit’s memory for up to
600 DVD discs, 2,000 titles. It is helpful when finding a desired title
(or play list) by sorting according to the sort options registered
during (or after) recording.
4 Press rt w e to select one play list you want to delete, then
press ENTER.
5 Press w e to select “DELETE”, then press ENTER.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● When you cancel the deletion, select “CANCEL”, then press ENTER.
6 Press EDIT to return to the normal screen.
NOTE:
information are not affected at all.
CABLE/DBS
TV
DVD
HDD
Modify Index
DVD
A Perform steps 1 – 4 of “Edit Scenes” (੬ pg. 67) before
continuing.
B Perform steps 5 – 8 of “Modify Index” (੬ pg. 64).
Modify Play List Name
A Perform steps 1 – 4 of “Edit Scenes” (੬ pg. 67) before
continuing.
B Perform steps 2 – 5 of “Modify Title Name” (੬ pg. 64).
NAVIGATION
ENTER
rtwe
Modify Category
A Perform steps 1 – 4 of “Edit Scenes” (੬ pg. 67) before
continuing.
B Perform steps 2 – 4 of “Modify Category” (੬ pg. 65).
Scan For Title From Library
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press rt w e to select the
NAVIGATION
appropriate sort button to sort the
DVD NAVIGATION
information, then press ENTER.
“DATE” : Sort by date
ORIGINAL
PLAY LIST.
SELECT WITH [
]
THEN PRESS [ENTER]
“DISC No.” : Sort by disc number
“CATEGORY” : Sort by category
“NAME” : Sort by name
● “DATE” and “DISC No.” are
available for the DVD deck only.
PRESS [NAVIGATION]
TO EXIT
DVD LIBRARY
DATE
DISC No.
NAME
NAVIGATION
EXIT
ENTER
A
CATEGORY
SELECT
3 Press rt w e to select the desired title, then press ENTER.
● Playback begins automatically after the selected title is located.
NOTE:
If a disc registered in the library is recorded or modified on DVD units
from other manufacturers, it may become impossible to operate
properly.
Register Disc
When a disc that is not registered in the library is loaded, a
message appears confirming if the disc should be registered. If
registering, perform the following procedure.
1 Press w e to select “REGISTER”, then press ENTER to confirm
the registration.
2 Press NAVIGATION to return to the normal screen.
NOTES:
● It is not possible to register discs formatted on devices other than
JVC’s DVD recorders.
● It is not possible to register discs recorded on devices other than
JVC’s DVD recorders.
● It is not possible to register discs when “SAVE AS LIBRARY” is set to
“OFF”. (੬ pg. 82)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION ON HDD/DVD DECK
EN
69
Locating The Desired Group And Tracks
Playback With MP3/WMA/JPEG
Navigation
1 Load a disc.
2 Press NAVIGATION.
3 Press rt w e to select “ORIGINAL”, then press ENTER.
4 Press rt to select the desired
NAVIGATION > ORIGINAL
group, then press ENTER.
GROUP
:
001/100
TRACK
:
001/100
0 : 07 : 01
IT’S SHOWTIME ! ! /B’z
● A list of files in the selected group
appears.
This unit can play back discs that MP3/WMA sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/WMA/JPEG Navigation enables you to search and select
the desired files recorded on CD-R/RW or CD-ROM discs very
easily.
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
003. SEXY GUY/GOMAKI
CLUB
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
006. REASON/ASAMI
FOREIGN GROUP
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
5 Press rt to select the desired
item, then press ENTER. The unit
starts playback from the selected
item.
● The unit stops when all items in
the selected group are played
back.
NAVIGATION > ORIGINAL
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD to select the DVD deck.
GROUP
:
001/100
TRACK
:
001/100
0 : 07 : 01
IT’S SHOWTIME ! ! /B’z
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
003. SEXY GUY/GOMAKI
CLUB
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
006. REASON/ASAMI
FOREIGN GROUP
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
NOTES:
● If you press SELECT(4) instead
NAVIGATION > ORIGINAL
GROUP
:
001/100
TRACK
:
001/100
0 : 07 : 01
IT’S SHOWTIME ! ! /B’z
of ENTER in step 4, the unit starts playback from the first file of the
group.
● JPEG files are played back as a slide show at the set intervals.
(੬ pg. 39)
● If a file name includes any 2-byte character, the unit may not show
the file name correctly.
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
003. SEXY GUY/GOMAKI
CLUB
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
006. REASON/ASAMI
FOREIGN GROUP
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
● The order of the groups and items shown in steps 4 and 5 may differ
from the order shown on your PC.
A Selected group number/total number of groups on the disc
B Selected file number/total number of files in the group that
contains the selected file
C Elapsed time (MP3 only)
D Name of the selected file
E Group name
F Selected file
NOTE:
If there are more than 100 files, the rest of the files are not
displayed. In this case, press ON SCREEN to display them on the
TV screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
70
6 Press w e to select “EXECUTE”, then press ENTER. The
dubbing screen appears for 5 seconds. To display the dubbing
screen again, press ON SCREEN.
EXECUTE: Select this to continue the dubbing operations.
CANCEL: Select this to cancel dubbing operation.
Dubbing
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
NOTES:
● Play lists are dubbed as programs.
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list.
● During dubbing, it is not possible to play back on HDD or DVD, or to
set timer programming.
CABLE/DBS
TV
DVD
HDD
VHS
DVD
Just Dubbing (From HDD To DVD)
By using Just Dubbing function, when dubbing all selected original
recordings and/or play lists, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the selected recordings and/or play lists to be dubbed
and the available disc space.
MARK
DUBBING
ENTER
rtwe
4
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]DVD”, then press ENTER.
4 Press rtw e to select “JUST”, then press ENTER.
7
8
9
ON SCREEN
5 Perform steps 5 – 6 of “High Speed Dubbing (From HDD To
DVD)”.
NOTES:
● Play lists are dubbed as programs.
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list. However, the
lower transfer rate cannot be dubbed in the higher transfer rate.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to “About Disc Remaining Display” (੬ pg. 73).
● During dubbing, it is not possible to play back on HDD or DVD, or to
set timer programming.
AUDIO
NOTES:
● It is not possible to dub simultaneously when timer programming is
set. Select either dubbing or timer programming.
● The order of the index which are displayed by pressing DUBBING
differs from the images displayed by pressing NAVIGATION or EDIT.
High Speed Dubbing (From HDD To DVD)
It is possible to dub the original recordings and/or play lists on the
HDD deck to DVD discs. The dubbing is performed in high speed,
keeping the original transfer rate.
It is possible to perform dubbing in the desired transfer rate.
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]DVD”, then press ENTER.
4 Press rtw e to select “MANUAL”, then press ENTER.
NOTES:
● After accessing the Dubbing Menu screen, it is not possible to take
out a disc.
● It is not possible to dub copy-once titles in Video mode.
● When dubbing a copy-once title, the data will be moved from HDD to
DVD upon completing dubbing.
● When you cancel dubbing a copy-once title during dubbing, the
original recording on the HDD deck remains and the title copied to a
DVD disc is deleted.
● It is not possible to dub play lists which contain copy-once titles.
● It is not possible to dub the following programs to DVD-R/RW disc
(Video mode):
● which contains more than one audio language.
● which is on the play list.
5 Perform step 5 of “High Speed Dubbing (From HDD To DVD)”.
The Manual Dubbing screen appears.
6 Press rt to select “REC MODE”, then press ENTER. Press
rt to select the desired option, then press ENTER.
7 Press rt to select “CONFIRM”, then press ENTER. The
confirmation screen appears.
8 Press w e to select “EXECUTE”, then press ENTER. The
dubbing screen appears for 5 seconds. To display the dubbing
screen again, press ON SCREEN.
EXECUTE: Select this to continue the dubbing operations.
● which is edited (also Live Memory Recording).
● which is recorded in LP mode or FP155-FP240 mode.
● Recording may not be performed in the highest speed depending on
the characteristics of the disc used.
CANCEL: Select this to cancel dubbing operation.
NOTES:
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list. However, the
lower transfer rate cannot be dubbed in the higher transfer rate.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to “About Disc Remaining Display” (੬ pg. 73).
● During dubbing, it is not possible to play back on HDD or DVD, or to
set timer programming.
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]DVD”, then press ENTER.
5 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to “About Disc Remaining Display” (੬ pg. 73).
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
71
Dubbing From HDD To VHS
It is possible to perform dubbing from the HDD deck to the VHS
deck.
Dubbing From DVD To VHS
It is possible to perform dubbing from the DVD deck to the VHS
deck.
1 Load a cassette with the record safety tab intact.
1 Load the disc you want to dub onto the DVD deck, and a
cassette with the record safety tab intact to the VHS deck.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]VHS”, then press ENTER.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “DVD ]VHS”, then press ENTER.
4 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
4 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
● You can select up to 8 original recordings and/or play lists.
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
7 Press t to select “CONFIRM”, then press ENTER.
7 Press t to select “CONFIRM”, then press ENTER.
8 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
8 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
9 While holding 7, press 9 so that the VHS deck enters the
record pause mode.
9 While holding 7, press 9 so that the VHS deck enters the
record pause mode.
10 Press HDD so that the HDD lamp lights up on the unit.
The dubbing screen will appear.
10 Press DVD so that the DVD lamp lights up on the unit.
The dubbing screen will appear.
11 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
11 Press w e to select “EXECUTE”, then press ENTER to
● To cancel the dubbing, press the 8 then w e to select “CANCEL”
and press ENTER to confirm.
confirm.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
Original Dubbing (From DVD To HDD)
It is possible to dub the original recordings on DVD discs to the
HDD deck.
NOTES:
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub Video CDs/SVCDs or Audio CDs.
● When dubbing is in progress, only 8 is functional.
1 Load a disc you want to dub.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “DVD ]HDD”, then press ENTER.
4 Press rtw e to select “TITLE”, then press ENTER.
5 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
6 Press w e to select “EXECUTE”, then press ENTER to start
dubbing.
EXECUTE: Select this to continue the dubbing operations.
CANCEL: Select this to cancel dubbing operation.
7 Press w e to select “EXECUTE”, then press ENTER for
confirmation. The dubbing screen appears for 5 seconds.
NOTES:
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub pre-recorded DVD VIDEO discs.
● It is not possible to dub Video CDs/SVCDs or Audio CDs.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
72
10 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
Dubbing From VHS To HDD
(Dubbing An Entire Cassette)
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the VHS deck to the HDD deck using
the “ENTIRE” dubbing.
NOTES:
“AUTO” after dubbing is completed.
1 Load the cassette you want to dub.
● The program information at the VHS deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the HDD
deck will enter into pause mode. Dubbing will resume once recorded
portion is detected.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
● Set “PICTURE CONTROL” to “EDIT” (੬ pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (੬ pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
completed.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]HDD”, then press ENTER.
4 Press w e to select “ENTIRE”, then press ENTER.
● When dubbing is in progress, only 8 is functional.
Dubbing From VHS To DVD
(Dubbing An Entire Cassette)
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the VHS deck to the DVD deck using
the “ENTIRE” dubbing.
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
1 Load the cassette you want to dub.
● Set “PICTURE CONTROL” to “EDIT” (੬ pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (੬ pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
completed.
7 Press t to select “CONFIRM”, then press ENTER.
8 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]DVD”, then press ENTER.
4 Press w e to select “ENTIRE”, then press ENTER.
● If the tape is not rewind, the unit will start dubbing after automatically
rewinding the tape to the beginning.
● Upon completing dubbing, the tape will automatically be rewind.
NOTES:
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
“AUTO” after dubbing is completed.
● The program information at the VHS deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the HDD
deck will enter into pause mode. Dubbing will resume once recorded
portion is detected.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
7 Press t to select “CONFIRM”, then press ENTER.
8 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● When dubbing is in progress, only 8 is functional.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
● If the tape is not rewind, the unit will start dubbing after automatically
rewinding the tape to the beginning.
Dubbing From VHS To HDD
(Dubbing A Program From Cassette)
● Upon completing dubbing, the tape will automatically be rewind.
It is possible to dub a single title (program) of a cassette from the
VHS deck to the HDD deck using the “1 PROG.” dubbing.
NOTES:
“AUTO” after dubbing is completed.
1 Load the cassette you want to dub.
● Set “PICTURE CONTROL” to “EDIT” (੬ pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (੬ pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
completed.
● The program information at the VHS deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the DVD
deck will enter into pause mode. Dubbing will resume once recorded
portion is detected.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]HDD”, then press ENTER.
4 Press w e to select “1 PROG.”, then press ENTER.
● When dubbing is in progress, only 8 is functional.
5 After pressing r and ENTER, press rt to select the recording
mode, then press ENTER.
6 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
7 Press AUDIO to select the playback sound.
8 Press 4 to locate the point from where you want to start
dubbing, then press 9.
VHS deck enters the record pause mode.
9 Press HDD so that the HDD lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
73
About Disc Remaining Display
When dubbing from HDD to DVD, the unit displays the time
information for dubbing by bar meter. By comparing the disc
remaining time and the necessary time for dubbing of the selected
items, it is possible to check if the dubbing can be performed
completely or not.
Dubbing From VHS To DVD
(Dubbing A Program From Cassette)
It is possible to dub a single title (program) of a cassette from the
VHS deck to the DVD deck using the “1 PROG.” dubbing.
1 Load the cassette you want to dub.
● Set “PICTURE CONTROL” to “EDIT” (੬ pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (੬ pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
completed.
When performing the High Speed Dubbing
Capacity of a disc
Remaining capacity
21%
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]DVD”, then press ENTER.
4 Press w e to select “1 PROG.”, then press ENTER.
Dark green: Length of already recorded item
Light green: Length of selected item
Yellow: Length of the item now being selected by arrow
Red: Excess over the capacity
5 After pressing r and ENTER, press rt to select the recording
mode, then press ENTER.
6 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
When performing the Just Dubbing
TOTAL 105MIN
7 Press AUDIO to select the playback sound.
8 Press 4 to locate the point from where you want to start
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The total time of a loaded disc is displayed on the right of the bar
meter.
dubbing, then press 9.
VHS deck enters the record pause mode.
9 Press DVD so that the DVD lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
When performing the Manual Dubbing
10 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
MAX FR240
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The available highest transfer rate is displayed on the right of the bar
meter.
NOTES:
● “SUPERIMPOSE” is automatically set to “OFF”. It will return to
“AUTO” after dubbing is completed.
● The program information at the VHS deck will not be dubbed.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
NOTE:
The bar meter moves up and down regularly, but this is not a
malfunction.
● When dubbing is in progress, only 8 is functional.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
74
1 Connect a camcorder or DV equipment to the [DV IN] connector
on the unit’s front panel.
DV Dubbing (HDD & DVD Deck Only)
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
on the remote so that the HDD lamp lights up on the unit.
3 Press CH +/– to set the channel to “DV”.
4 Press ON SCREEN.
● The on-screen display for DV dubbing appears.
NOTES:
5 Press w e to select
, then press ENTER to display
● Use the DV cable VC-VDV 204U for connection.
● When you connect a PC to the DV IN connector, we do not assure
the normal operation of this unit.
the remote icon (facing to the right) for the DV equipment.
6 Press REC MODE repeatedly to set the recording mode.
7 Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9.
Your unit
● To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
● To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
● To change the playback direction, press 3 or 5.
8 Press w e to select
, then press ENTER repeatedly
until the desired sound track appears on the TV screen.
To [DV IN]
AUDIO 1: Select this to record the original stereo sound played
back on the connected DV equipment.
AUDIO 2: Select this to record the dubbed stereo sound played
back on the connected DV equipment.
MIX: Select this to record the sound of both “AUDIO 1” and
“AUDIO 2”.
● Note that this selection is not available when the source program is
recorded in 16BIT (48 kHz) mode.
Camcorder
DV cable
(VC-VDV 204U)
(not supplied)
9 Press w e to select
, then press ENTER. The
dubbing starts.
● Playback on the external DV equipment and recording on the unit
should start simultaneously.
● To pause dubbing, press w e to select
, then press
DV connector
DV equipment
ENTER. Both the unit and the external DV equipment pause
dubbing. Pressing 9 on the unit also works the same way.
10 Press w e to select
, then press ENTER. Then
, then press ENTER.
press 8. The DV equipment stops.
11 Press w e to select
12 Press 8 twice on the remote control to stop dubbing.
The following on-screen display for DV dubbing appears when
● Both the unit and the external DV equipment stop dubbing.
ON SCREEN is pressed while the channel has been set to “DV”.
NOTES:
● Dubbing copyright guarded programs is not possible.
● Original DV information such as the recording date and time are not
recorded.
0:00
FR360 00:00:00. 00
12bit
DV JVC
1:00
2:00
GR-DV3500
00:00:00. 00
DV
HDD
L
–
R
GR-DV3500
SOUND1
● The superimposed indication during the operation or dubbing is not
recorded.
● If the dubbing is paused while the channel is set to “DV”, you cannot
switch channels.
1
2
DV
DV
When you dub from DV equipment other than a
camcorder
A
B
C
A Remote control switch
To switch between the devices operable by the remote control
unit. The unit is operable when the remote icon (
displayed faces to the left, while the DV device is operable
when the remote icon is facing to the right.
A Perform step 1 to 4.
B Locate the point from where you want to start dubbing, then
stop on the DV equipment.
)
● If you pause the DV equipment in this step, a few second’s still
picture will be recorded at the beginning of the recorded program.
C Set the input mode to “DV INPUT” on the DV equipment.
● If you select an input mode other than “DV INPUT”, unwanted
pictures may be recorded at the beginning of the recorded
program.
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the
unit (such as in camera mode), proceed with normal recording
(੬ pg. 41, 44).
* Preroll editing refers to the playback after the DV tape is slightly
rewind. (For DV devices that do not support the –1 speed, the
rewinding time may be longer.)
D Perform step 9 to 12.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press w e to select
.
Locate the point where you want to restart dubbing by pressing 4,
5, or 3, then press 8.
C Sound monitor switch
For selecting the desired sound format for recording. It is not
selectable during dubbing.
Press w e to select
dubbing.
, then press ENTER to restart
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
75
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Make connections.
Edit From A Camcorder
You can use a camcorder as the source player and your unit as the
recording deck.
A If the camcorder has no S-VIDEO output connector:
— connect the camcorder’s AUDIO/VIDEO OUT connectors to the
unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front
panel.
A If the camcorder has no S-VIDEO output connector:
● When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
B If the camcorder has an S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input connectors
on the front panel.
2 Press VHS/HDD/DVD SELECT on the unit repeatedly to select
Recorder
To [VIDEO/AUDIO
((MONO) L/R)] input
the recording deck.
3 Press CH +/– to select “F-1”.
● Set “FRONT AUX F-1” to “VIDEO” for the VIDEO input connector, or
“S-VIDEO” for the S-VIDEO input connector, depending on the
connector being used. (੬ pg. 83)
Audio/video cable
(not supplied)
4 Press REC MODE repeatedly to set the recording mode.
5 Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
6 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control. The dubbing starts.
7 Press 8 on the unit, then stop playback on the camcorder.
NOTES:
AUDIO/VIDEO OUT
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating procedure.
● The quality of dubbed picture becomes poorer than that of the
original.
Player
B If the camcorder has an S-VIDEO output connector (HDD
& DVD deck only):
To
[S-VIDEO]
input
Recorder
To [AUDIO] input
S-video cable
(not supplied)
Audio cable
(not supplied)
S-VIDEO OUT
AUDIO OUT
Player
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
76
Slide the TV/CABLE/DBS/DVD switch to DVD.
Edit To Or From Another Recorder
1 Make connections.
You can use your unit as the source player or as the recording
deck.
A When recording on HDD or DVD deck
1.If another recorder has no S-VIDEO connector, connect the unit’s
[AUDIO/VIDEO INPUT] connectors to the audio/video output
connectors on another recorder.
NOTE:
When using another recorder as the recording deck, refer to its
instruction manual.
2.If another recorder has S-VIDEO connector, connect the
[AUDIO INPUT] and [S-VIDEO INPUT] connectors to the audio and
S-video output connectors on another recorder.
● If connecting a unit with an S-VIDEO connector, it is recommended to
use an optional S-Video cable to minimize picture degradation while
editing.
A When recording on HDD or DVD deck
Your unit
B When recording on VHS deck
1.Connect the unit’s [AUDIO/VIDEO INPUT] connectors to the audio/
video output connectors on another recorder.
Recorder
2 Press VHS/HDD/DVD SELECT on the unit repeatedly to select
TV receiver
the recording deck.
3 Press CH +/– to select “L-1” when using this unit as the
recording deck.
For HDD/DVD deck
● Set “REAR AUX L-1” to “VIDEO” for the VIDEO input connector, or
“S-VIDEO” for the S-VIDEO input connector, depending on the
connector being used. (੬ pg. 83)
4 Press REC MODE repeatedly to set the recording mode.
5 Engage the Play mode of the source player.
6 Engage the Record mode of the recording deck.
Another recorder
7 Stop recording on the recording deck, then stop playback on the
source player.
NOTES:
Player
● All necessary cables can be obtained from your dealer.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting. (੬ pg. 82)
B When recording on VHS deck
Your unit
.
Recorder
TV receiver
Another recorder
Player
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
77
1 Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
Digital Audio Dubbing
2 Place a disc on the unit and load an MD on the connected digital
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
audio device.
3 Select the audio to be dubbed.
However, it is not possible to dub copy-protected discs.
4 Start playback slightly before the actual point from where you
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
wish to start dubbing.
5 Press 9 to pause playback.
Example: Dubbing to an MD
Recorder
6 Select the input mode on the connected digital audio device.
7 Press 4 to start playback on the unit.
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press 8 to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where you
intend editing to start, and where it actually starts.
Digital audio device
(MD deck, etc.)
Coaxial cable
(not supplied)
Optical cable
(not supplied)
To [DIGITAL AUDIO
OUT (OPTICAL)]
To [DIGITAL
AUDIO OUT
(COAXIAL)]
Player
.
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
EN
78
Remote Control Functions
Remote Control 1/2/3/4 Code Switching
CABLE/DBS
TV DVD
TV /VIDEO
1
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of four codes
(1, 2, 3 or 4). The remote control is preset to send 3 code signals
because your unit is initially set to respond to 3 code signals. You
can easily modify your unit to respond to 1, 2 or 4 code signals.
TV VOLUME +/–
CH +/–
0 – 9
TV MUTING
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ENTER
1
4
SET UP
CABLE/DBS
TV
DVD
1 – 4
TV Multi-Brand Remote Control
Your remote control can operate the basic functions of your TV set.
In addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
ENTER
● Turn off the TV using its remote control.
● Slide the TV/CABLE/DBS/DVD switch to TV.
IMPORTANT:
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with your
8
SET UP
● Keep pressing SET UP down during step 1.
1 Enter your TV’s brand code using the number keys, then press
ENTER.
2 Press 1 on the unit’s remote control to turn on the TV and try
operations (੬ step 3).
● Once you have set the remote control to operate the TV, you do not
have to repeat this step until you replace your remote control’s
batteries.
● Some brands of TVs have more than one code. If the TV does not
function with one code, try entering another.
● Keep pressing SET UP down during step 1.
1 Press the number key “1” for 1, “2” for 2, “3” for 3 or “4” for 4
3 Press the corresponding buttons to operate the TV: 1, TV/
VIDEO, CH +/–, TV VOLUME +/–, TV MUTING, number keys.
● For some brands of TVs, you must press ENTER after having
pressed the number keys.
to change the remote control code, then press ENTER.
2 Press 1 on the unit to turn off the unit.
off. The code currently set appears on the front display panel.
BRAND NAME
CODE
4 Press 8 on the remote control to change the unit’s code. The
code currently set on the remote control blinks on the front display
panel for approximately 5 seconds, and is applied to the unit.
JVC
01, 03
10
02
03
04, 11
05
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
NOTE:
When “POWER SAVE” is set to “ON” (੬ pg. 83), it is not possible to
change the remote code.
SHARP
SONY
06
07
SAMSUNG
SANYO
SEARS
12
13
13
TOSHIBA
ZENITH
08
09
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
EN
79
Cable Box Or DBS Receiver Multi-Brand Remote
Control
box or DBS (Direct Broadcast Satellite) receiver set. In addition to
JVC cable boxes or DBS receivers, other manufacturer’s cable
boxes or DBS receivers can also be controlled.
CABLE BOX BRAND
CODE
ARCHER
01, 05, 17
01, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
02
01, 17
15, 16, 17, 21, 25
15
01, 04, 06, 11, 12, 15, 28
10, 18, 23
15
01, 04, 06, 11, 12, 15, 28
02
07
13, 14
15, 16, 17, 21, 25
13, 14
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
● Keep pressing SET UP down during step 1.
1 Enter your cable box or DBS receiver’s brand code using the
JASCO
number keys, then press ENTER.
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
2 Press 1 on the unit’s remote control to turn on the cable box or
DBS receiver and try operations (੬ step 3).
● Once you have set the remote control to operate the cable box or
DBS receiver, you do not have to repeat this step until you replace
your remote control’s batteries.
● Some brands of cable box or DBS receiver have more than one
code. If the cable box or DBS receiver does not function with one
code, try entering another.
10, 18, 23
01, 16, 17
05, 16, 24
02
3 Press the corresponding buttons to operate the cable box or
DBS receiver: 1, CH +/–, number keys.
07
● For some brands of cable box, you must press ENTER after having
pressed the number keys.
SL MARX
05, 16, 17, 24, 25
13, 14
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
SPRUCER
STARGATE
TELEVIEW
TOCOM
IMPORTANT:
It may not work with your cable box, or in some instances, may have
limited function capability.
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
16, 17, 25
03, 09, 22
03, 09, 22
NOTES:
● You must set the brand for your remote control and for your
Controller (੬ pg. 24) separately. The list of brands that can be
controlled by your remote control is different from the list of brands
that can be controlled by your controller.
● It’s not possible to operate a cable box or DBS receiver that is not
equipped with a receiving window.
● It’s not possible to set the remote control for both your cable box and
a DBS receiver at the same time. You can only set the remote control
to operate one of these units at a time.
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
51
51
41
40
RCA (DSS)
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM CONNECTIONS
EN
80
1 Connect the unit and a Dolby Digital Decoder or an amplifier
optional coaxial cable.
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
NOTES:
● For Dolby Digital sound, set “DIGITAL AUDIO OUT” to “DOLBY
DIGITAL/PCM”. (੬ pg. 81)
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
● For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/PCM”.
(੬ pg. 81)
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards to its
Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to the
speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely affect
the playback picture.
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO input
Optical cable
(not supplied)
Coaxial cable
(not supplied)
To [DIGITAL
AUDIO OUT
(COAXIAL)]
To [DIGITAL AUDIO
OUT (OPTICAL)]
.
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
81
* The boldface settings below indicate the settings at your purchase.
Mode Set
AUDIO OUTPUT
(HDD & DVD Deck Only)
8 DIGITAL AUDIO OUT — DOLBY DIGITAL/PCM / STREAM/
PCM / PCM ONLY
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Set to the appropriate mode according to the type of the device
connected to [DIGITAL AUDIO OUTPUT] connector.
DOLBY DIGITAL/PCM: Select this when you connect the digital
input connector of a Dolby Digital Decoder or an amplifier with a
built-in Dolby Digital Decoder.
CABLE/DBS
TV
DVD
STREAM/PCM: Select this when you connect the digital input
connector of an amplifier with a built-in DTS, Dolby Digital, or
MPEG multichannel decoder.
HDD
DVD
PCM ONLY: Select this when you connect the linear PCM digital
input of other audio equipment (amplifier, MD or DAT deck, etc.).
NOTES:
● This setting also functions when HDD is active.
● If you watch or play back a title which contains multiple audio
languages, select “PCM ONLY” in advance and choose main or sub
audio with AUDIO.
ENTER
rtwe
8 ANALOG AUDIO OUT — STEREO / DOLBY SURROUND
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO: Select this when listening to conventional two-channel
stereo audio with the unit’s [AUDIO OUTPUT] connectors
connected to a stereo amplifier/receiver or TV set, or in case you
want to record the audio from a DVD VIDEO disc to a Mini Disc,
etc.
SET UP
DOLBY SURROUND: Select this when listening to multichannel
surround audio with the unit’s [AUDIO OUTPUT] connectors
connected to an amplifier/receiver with a built-in surround
decoder or a surround decoder.
AUDIO
Various modes of this unit are categorized into menus nested in 2
modes, find the desired mode in the menu (for details on each
menu, see pages 81 through 82), then follow the procedure below.
MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a program
encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
enjoy wide dynamic range program.
DVD VIDEO SET UP
PARENTAL LOCK (੬ pg. 40)
HDD/DVD SET UP
FUNCTION SET UP
INITIAL SET UP
HDD SET UP (੬ pg. 82)
DVD SET UP (੬ pg. 82)
speaker(s).
NOTES:
DISPLAY SET (੬ pg. 82)
VIDEO IN/OUT (੬ pg. 26, 83)
● This function has no effect on programs other than that recorded in
Dolby Digital format.
● This function does not work when Simulated Surround Effect is
activated. (੬ pg. 38)
● The effect of “NORMAL” and “WIDE RANGE” may not be different
depending on discs.
TUNER SET (੬ pg. 23)
STB SET (੬ pg. 24)
CLOCK SET (੬ pg. 22)
8 OUTPUT LEVEL — STANDARD / LOW
You can lower the output level of analog audio to accommodate
the unit to the connected A/V equipment.
STANDARD: Normally select this setting.
LOW: The output level of analog audio is lowered.
● The procedure below shows how to set the desired option of the
“2ND AUDIO REC” mode as an example.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “FUNCTION SET UP”, then press t.
4 Press w e to select “REC/PLAY
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
SET UP”, then press t.
REC/PLAY SET UP
DISPLAY SET
VIDEO IN/OUT
XP MODE REC AUDIO
DOLBY DIGITAL
5 Press rt to select “2ND
2ND AUDIO REC
JUMP TIME
OFF
AUDIO REC”, then press ENTER.
15MIN
6 Press rt to select the desired
option, then press ENTER.
SET UP
EXIT
ENTER
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
7 Press SET UP to complete the
SELECT
setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
82
DISC PLAY SET UP
REC/PLAY SET UP
8 RESUME — OFF / ON / DISC RESUME
When this function is set to “ON” or “DISC RESUME”, you can use
the resume function. (੬ pg. 29)
OFF: You cannot use the resume function.
ON: You can start playback from the resume point of the placed
disc.
DISC RESUME: The unit retains a memory of the resume points of
the last 30 discs played back, even though they have been
ejected.
8 XP MODE REC AUDIO — DOLBY DIGITAL / LINEAR PCM
You can select the audio format when you record a title in XP
mode. When this function is set to “LINEAR PCM”, you can obtain
a high-quality audio sound.
DOLBY DIGITAL: To record in Dolby Digital format.
LINEAR PCM: To record in Linear PCM format.
8 2ND AUDIO RECORD — OFF / ON
When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
NOTE:
“DISC RESUME” setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other types
of discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”.
recorded.
HDD SET UP
NOTE:
When the channel is changed on the unit;
8 LIVE MEMORY — OFF / 30 MIN / 1 HR / 3 HR
When this function is set to “30 MIN”, “1 HR” or “3 HR”, you can
apply the selected time length to “Temporary recording for Live
Memory” (੬ pg. 47).
● The “MONO” indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
● Both “MONO” and “SAP” indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
DVD SET UP
8 SAVE AS LIBRARY — OFF / ON
When this function is set to “ON”, the recording information is
automatically stored in the library. For details, refer to “Modify
Library Information” (੬ pg. 68).
8 JUMP TIME — 15 MIN / 30 MIN / 1 HR
You can locate a scene ahead of or behind the currently viewed
one by jumping a selected time interval during playback (or Live
Memory Playback) or recording (or Live Memory Recording). For
details, refer to “Jump Search” (੬ pg. 49)
8 CONTINUOUS PLAY — OFF / ON
When this function is set to “ON”, multiple titles on a disc are
played back continuously one after another.
DISPLAY SET
8 VIDEO MODE RECORDING ASPECT — PRIORITIZE 4:3 /
8 SUPERIMPOSE — OFF / AUTO
When this function is set to “AUTO”, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (੬ pg. 21)
OFF: To turn off superimposed indications.
AUTO: To superimpose operational indications for approximately
five seconds just after the corresponding operation.
PRIORITIZE 16:9
This is the setting for the aspect ratio used when you dub titles to
DVD discs in video mode. If the titles you want to dub are recorded
in both 16:9 and 4:3, you must select one aspect ratio.
PRIORITIZE 4:3: If you select “PRIORITIZE 4:3”, even a title
recorded in 16:9 is dubbed in 4:3.
PRIORITIZE 16:9: If you select “PRIORITIZE 16:9”, even a title
recorded in 4:3 is dubbed in 16:9.
NOTES:
● Even when “SUPERIMPOSE” is set to “OFF”, you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting. (੬ pg. 76)
● When you select “AUTO”, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8 VIDEO MODE RECORDING AUDIO — MAIN / SUB
This is the setting for the audio channel to be selected when
dubbing titles to DVD discs in video mode. Select either one of the
two settings if the titles to be dubbed have two audio channels.
MAIN: Select this to dub the main channel.
SUB: Select this to dub the sub channel.
8 MP3 & WMA / JPEG — MP3 & WMA / JPEG
You can select files to play back, when both MP3&WMA files and
JPEG files are recorded on a disc.
MP3 & WMA: Select this to play back MP3/WMA files.
JPEG: Select this to play back JPEG files.
8 BLUE BACK — OFF / ON
When this function is set to “ON”, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
83
Scan Mode Set
8 DIMMER — BRIGHT / DIMMED
You can change the brightness of the front display panel.
BRIGHT: Normally select this.
If you connect the unit and TV with Component Video Connection
(੬ pg. 19), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction
of higher-quality images.
DIMMED: To dim the front display panel. (Blue lamp on the front
display panel is turned off.)
8 POWER SAVE — OFF / ON
When this function is set to “ON”, you can reduce the power
consumption while the unit is turned off.
— the front display panel will be turned off.
● Power Save does not work when —
— the unit is in the Timer mode.
8 Interlaced scan
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of the
second half of the picture in-between lines of the first half of the picture.
8 Progressive scan
Progressive scan displays all the horizontal lines of a picture at one time,
as a single frame. This system can convert the interlaced video from DVD
into progressive format for connection to a progressive display. It
dramatically increases the vertical resolution.
— the unit’s power is turned off after timer-recording or Instant Timer
Recording.
— the Automatic Satellite Program Recording mode is engaged.
(੬ pg. 59)
● It takes some time for the unit to complete initialization after you turn
on the unit power, with “WAKE UP” blinking on the front display
panel.
ATTENTION:
Your TV needs to be compatible with Progressive.
8 ON SCREEN LANGUAGE
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
This unit offers you the choice to view on-screen messages in 3
different languages.
For details, refer to “On-screen Language Set” (੬ pg. 21).
CABLE/DBS
VIDEO IN/OUT
TV
DVD
8 MONITOR TYPE — 4:3LB / 4:3PS / 16:9 AUTO / 16:9 FIX
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
For details, refer to “Monitor Set” (੬ pg. 26).
HDD
DVD
8 FRONT AUX F-1 — VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (F-1)
being used on the front panel.
VIDEO: To use the [VIDEO] input connector on the front panel.
S-VIDEO: To use the [S-VIDEO] input connector on the front panel.
1
2
Press HDD or DVD so that the HDD or DVD lamp lights up on the unit.
Press PROGRESSIVE SCAN for 3 or more seconds.
8 REAR AUX L-1 — VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (L-1)
being used on the rear panel.
●
●
Video output indicator ( ) lights on the front display panel if Progressive
scan mode has been established. ( pg. 14)
੬
Each press of PROGRESSIVE SCAN for 3 or more seconds switches the
scan mode.
VIDEO: To use the [VIDEO INPUT] connector on the rear panel.
S-VIDEO: To use the [S-VIDEO INPUT] connector on the rear
panel.
.
NOTES:
● Interlaced scan mode is the setting at your purchase.
● Interlaced scan mode might be suitable depending on video material.
● Scan mode cannot be set while menu screen is displayed.
● When the Progressive scan mode is engaged, no video signal is
output from [S-VIDEO OUTPUT] connector and [VIDEO/AUDIO
OUTPUT] connectors.
Watch the images on VHS deck in the Progressive scan
mode via component video
1
2
Set the Progressive-compatible TV to the component input mode.
Press HDD or DVD so that the HDD or DVD lamp lights up on the
unit.
3
Press PROGRESSIVE SCAN for 3 or more seconds.
●
The video output indicator
lights up on the front display panel.
4
Press VHS so that the VHS lamp lights up on the unit, then press
PROGRESSIVE SCAN
.
●
“COMP OFF” is displayed on the front display panel. It will be displayed for
5 seconds.
5
Press PROGRESSIVE SCAN again within 5 seconds.
●
●
The VHS progressive scan image will then be outputted from the
[COMPONENT VIDEO OUT (Y/P /P )] connectors.
B
R
NOTES:
● Be sure to engage the HDD or DVD deck in stop mode.
● To disengage the VHS Progressive Scan mode, perform steps 4
and 5 to switch to “COMP OFF”.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
84
* The boldface settings below indicate the settings at your purchase.
Mode Set
(VHS Deck Only)
FUNCTION
8 PICTURE CONTROL — NORM / EDIT / SOFT / SHARP
This feature helps you to adjust the playback picture quality
according to your preference. Normally select “NORM”.
NORM: Picture quality is adjusted automatically.
EDIT: Minimizes picture degradation during editing (recording and
playback).
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
SOFT: Reduces image coarseness when viewing overplayed tapes
containing a lot of noise.
TV
DVD
SHARP: Clearer, sharper-edged picture when viewing images with
lots of flat, same-colored surfaces such as cartoons.
VHS
NOTES:
● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will
not change until you select another mode.
you finish dubbing the tapes.
8 SUPERIMPOSE — AUTO / OFF
When this function is set to “AUTO”, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (੬ pg. 21)
rtwe
ENTER
NOTES:
● Even when “SUPERIMPOSE” is set to “OFF”, you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting.
SET UP
● During playback, the operation mode indicators may be disturbed
depending on the type of tape being used.
8 AUTO SP]EP TIMER — ON / OFF
When this function is set to “ON”, the unit automatically switches to
EP mode to allow complete recording if there is not enough tape to
record the entire program while timer-recording in SP mode.
You can change various mode settings on the Function Set
screen.
To change the settings of these modes, find the desired mode in
the menu (for details on each menu, see pages 84 through 85),
then follow the procedure below.
For Example:
Recording a program of 140 minutes in length onto a 120-minute
tape.
1 Press VHS so that the VHS lamp lights up on the unit.
2 Press SET UP to access the
FUNCTION
Approximately 30 minutes
EP mode
Approximately 110 minutes
SP mode
Function Set screen.
PICTURE CONTROL
SUPERIMPOSE
NORM
AUTO
OFF
3 Press rt to select the item you
want to change, then press ENTER
or e to select the desired mode.
AUTO SP EP TIMER
VIDEO STABILIZER
BLUE BACK
OFF
Total 140 minutes
ON
OFF
2ND AUDIO RECORD
Make sure you set this function to “ON”, before the timer-recording
starts.
4 Press SET UP to complete the
(
,
) THEN (ENTER)
setting.
(SET UP) TO END
NOTES:
● If you have programmed the unit to timer-record 2 or more programs,
the second program and those thereafter may not fit on the tape if
you set “AUTO SP]EP TIMER” to “ON”. In this case, make sure the
mode is not engaged, then set the tape speed manually during timer
programming.
● In order to ensure that the recording fits on the tape, this feature may
leave a slight non-recorded section at the end of the tape.
● There may be some noise and sound disturbance at the point on the
tape where the unit switches from SP to EP mode.
● The Auto SP]EP Timer feature is not available during ITR (Instant
Timer Recording), and the feature will not work properly on the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
85
Tray Lock (DVD Deck Only)
8 VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct
vertical vibration in the picture when playing back unstable
recordings made on another recorder.
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
● Turn off the unit.
NOTES:
● When you finish viewing a tape, be sure to set this function to “OFF”.
● Regardless of the setting, this function has no effect during recording
and during special effects playback.
x
8
● The on-screen display may jitter vertically when this function is set to
“ON”.
● To watch recordings with close-caption, set this function to “OFF”.
8 BLUE BACK — ON / OFF
When this function is set to “ON”, the TV screen becomes all blue
when receiving a channel not in use.
To lock tray
While the unit is turned off, press and hold 8, then press x on the
unit. “LOCK” appears on the front display panel and the disc tray is
locked.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
To unlock tray
While the unit is turned off, press and hold 8, then press x on the
unit. “UNLOCK” appears on the front display panel.
8 2ND AUDIO RECORD — ON / OFF
When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
When this function is set to “OFF”, the SAP audio cannot be
recorded.
NOTE:
When the channel is changed on the unit;
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
86
®
Guide Channel Number Set
Changing VCR Plus+ Setting
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
The VCR Plus+ programming system assigns a VCR Plus+ guide
channel to the TV channels and the cable channels. These guide
channel numbers are also called the VCR Plus+ channel codes.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station.
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “TUNER
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
To ensure that VCR Plus+ timer recording operates correctly, it is
necessary to set the “VCR Plus+ Guide Channel” for each station.
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, perform the following steps to
set the correct guide channel number.
SET”, then press t.
TUNER SET
STB SET
CLOCK SET
AUTO CH SET
MANUAL CH SET
5 Press rt w e to select “GUIDE
CH SET”, then press ENTER.
GUIDE CH SET
11
12
13
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
NOTES:
SELECT
● In many instances, the VCR Plus+ guide channel numbers for cable
and broadcast TV stations DO NOT match the channel number on
which it is received by your unit or cable box. Check your TV listing,
or contact your cable supplier for details.
6 Press rt to select “GUIDE
CH”, then press ENTER.
11
2
13
INITIAL SET UP > GUIDE CH SET
GUIDE CH
CABLE CH
1
- -
7 Press rt to select the Guide
Channel number for the desired
station as shown in the TV listings.
Then press ENTER.
● If you receive your channels with a
cable box and if you have properly
set your Controller, “CABLE CH”
● Many TV stations can be viewed on cable. Check your TV listing, or
contact your cable supplier for details.
RETURN
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
SET UP
EXIT
ENTER
SELECT WITH [
PRESS [SET UP] TO EXIT
] THEN PRESS [ENTER]
SELECT
appears in place of “DVD CH”. If not, perform “Cable Box and/or DBS
Receiver Control Setting (HDD & DVD Deck only)” (੬ pg. 24).
CABLE/DBS
TV
DVD
Guide Channel Number’s broadcast is received by the unit or the
DBS receiver. Then press ENTER.
● To timer-record a satellite program with the VCR Plus+ system, you
need to install the provided Satellite Controller and perform the
procedure described in “Cable Box and/or DBS Receiver Control
Setting (HDD & DVD Deck only)” (੬ pg. 24).
● Repeat steps 6 – 8 as necessary.
9 Press SET UP to complete the setting.
ENTER
rtwe
Guide Channel Number
“Guide Channel (GUIDE CH) Number” refers to the assigned TV
station numbers, according to broadcast area, for the VCR Plus+
timer recording. The Guide Channel Numbers can be found in
most TV listings.
SET UP
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
87
Format A DVD-RAM Disc
Format A Disc (DVD Deck Only)
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “HDD/DVD SET UP”, then press t.
4 Press w e to select “DISC SET
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want to
delete all recordings and data on the disc.
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
UP”, then press t.
HDD SET UP
DVD SET UP
DISC SET UP
FINALIZE
Video
CANC. FINALIZ.
5 Press rt w e to select
“FORMAT”, then press ENTER.
Press w e to select “OK”, then
press ENTER.
ATTENTION:
FORMAT
● When a disc is formatted, all recordings and data are erased. It is
impossible to restore them.
SET UP
EXIT
ENTER
● Never turn off the unit or disconnect the AC power cord while
“NOW FORMATTING...” is displayed on the TV screen.
SELECT WITH [
] THEN PRESS [ENTER]
6 Press w e to select “OK”, then
PRESS [SET UP] TO EXIT
SELECT
press ENTER.
Format A DVD-RW Disc
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Load a DVD-RAM/RW disc to format.
1 Perform steps 1 to 4 of “Format A DVD-RAM Disc” as above
before continuing.
2 Press rt w e to select “FORMAT”, then press ENTER. Press
w e to choose “VR MODE” or “VIDEO MODE”, then press ENTER
when “DISC WILL BE FORMATTED” appears on the TV screen.
“VR MODE”: To be chosen when you want to record, erase, or edit
data on the disc repeatedly.
CABLE/DBS
TV
DVD
“VIDEO MODE”: To be chosen when you want to erase all the data
on the disc once played back to record new data, or play back the
disc on other DVD players.
3 Press w e to select “OK”, then press ENTER.
NOTES:
● It is impossible to format Version 1.0 DVD-RW discs in Video mode.
● It is impossible to format DVD-R discs.
● All the titles on a disc will be deleted once the disc is formatted even
if they are protected titles. (੬ pg. 65)
ENTER
rtwe
SET UP
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
88
Finalize A DVD-R/RW Disc
Finalize A Disc (DVD Deck Only)
1 Perform steps 1 to 4 of “Format A DVD-RAM Disc” (੬ pg. 87)
before continuing.
2 Press rt w e to select “FINALIZE”, then press ENTER.
● For DVD-R/RW (Video mode) discs, the background selection screen
will appear. Press rt w e to select the desired background from a
selection of 18 backgrounds.
Finalizing DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalized in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Title names input in the Library Database Navigation are
registered as title names in the DVD menu. (੬ pg. 64)
3 Press w e to select “OK”, then press ENTER.
4 Press w e to select “OK”, then press ENTER.
5 Press SET UP to return to the normal screen.
● Menu screen is cleared.
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
● Once a DVD-RW (VR mode) disc has been finalized, it can be played
on DVD players compatible with VR mode.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Load a DVD-R/RW disc to finalize.
Cancel The Finalization Of A DVD-RW Disc
CABLE/DBS
TV
DVD
1 Load a DVD-RW disc to cancel the disc finalization, and perform
steps 1 to 4 of “Format A DVD-RAM Disc” (੬ pg. 87) before
continuing.
2 Press rt w e to select “CANC. FINALIZ.”, then press ENTER.
3 Press w e to select “EXECUTE”, then press ENTER.
4 Press SET UP to return to the normal screen.
● When the disc finalization is canceled, the mode in which the disc
was formatted is restored, making the disc recordable. (੬ pg. 9, 87)
ENTER
rtwe
SET UP
Before finalizing
● It is possible to record on a blank space.
● It is possible to enter title names. (੬ pg. 64)
● It is possible to delete titles. (੬ pg. 65)
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
title is deleted from a DVD-R disc.
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalized.
After finalizing (For DVD-R/RW (Video mode) discs)
● Video and audio that have been recorded by then are recorded in
discs as DVD VIDEO discs.
● Although DVD-R/RW discs finalized on this unit become playable on
DVD players compatible with DVD-R/RW discs, some discs still may
not play, for which JVC cannot take responsibility.
● Marked points marked before finalizing will be deleted, and titles will
be divided automatically into “chapters” approximately every 5
minutes. (੬ pg. 29)
● Depending on the DVD players and DVD-R/RW discs used, and on
the conditions of recording, it may not be possible to play back the
discs. In this case, play back the discs on this unit.
● Additional recordings become impossible.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
89
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Playback (DVD Deck)
The DVD deck cannot be operated.
● The DVD deck is not selected.
]Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD
on the remote so that the DVD lamp lights up on the unit.
Initializing (DVD Deck Only)
Malfunction occurs on the unit.
Images do not appear on the TV screen.
]Press 1 to turn off the unit, press and hold 1, then press 8
for two seconds or more.
● The TV receiver’s channel selector is not set to the video
channel or AV mode.
]If you are using the RF connection, set the TV receiver to the
video channel.
General
]If you are using the AV, S-VIDEO or Component Video
connection, set the TV to its AV mode.
● The unit’s video channel has not been correctly set.
]Perform the video channel set. (੬ pg. 19)
● When interlace scanned program is played back, progressive
scan mode is selected.
No power is supplied to the unit.
● The AC power plug is disconnected from the AC outlet.
]Connect the AC power plug to the AC outlet securely.
(੬ pg. 19)
The remote control does not work properly.
]Press and hold PROGRESSIVE SCAN until
the front display panel. (੬ pg. 83)
disappears from
]Remove the batteries, wait for 5 minutes or more, then load the
butteries again.
Playback does not start or stop immediately after playback is
started by pressing
On the front display panel, “NO DISC” appears.
● The setting of the remote control code is inappropriate.
]Set the same remote control code (1, 2, 3, or 4) on both the unit
and the remote control. (੬ pg. 78)
.
● The batteries are discharged.
]Replace the dead batteries with new ones.
]Place the disc on the disc tray with the playback surface facing
down. (੬ pg. 10)
● A disc not being compatible with the unit is loaded.
]Load a playable disc on the unit. (੬ pg. 7)
● A dirty disc is loaded.
Dubbing from the external equipment is not possible.
● The source (another video recorder, camcorder) has not been
properly connected.
● All necessary power switches have not been turned on.
]Confirm that all units’ power switches are turned on.
● The setting of the input channel position is inappropriate.
]Select the input channel position (“F-1” or “L-1”) that
equipment. (੬ pg. 76)
]Clean the disc. (੬ pg. 11)
● Defective disc is loaded.
]Replace the warped or scratched disc with a normal one.
Images are blurred or distorted when you start High-Speed
Search.
]Images are blurred or distorted at the point where the playback
speed changes and this is not a malfunction of the unit.
The on-screen display superimposed on the program played
back/received on this unit is recorded when you dub the program
to an external recording equipment.
Playback does not start.
]Playback does not start for approximately 30 seconds after
]Set “SUPERIMPOSE” to “OFF”. (੬ pg. 82)
The unit does not operate.
Playback does not start when you select a title or a chapter.
● There are cases when the operation is prohibited on the disc.
● The Parental Lock is engaged and the disc is rated higher than
the set level.
● Lightning or static electricity may cause malfunction of the unit.
]Press 1 to turn the power off, then press the button again to
turn the power on.
]Release the Parental Lock temporarily or change the set level.
Playback (HDD Deck)
The remote control of a JVC TV will not operate the unit.
● The setting of the remote control code is inappropriate.
]To operate the unit using a JVC TV remote control, set the
remote control code of the unit to “1” (Default: “3”). (੬ pg. 78)
The HDD deck cannot be operated.
● The HDD deck is not selected.
]Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
90
Playback (VHS Deck)
Recording (HDD Deck)
The VHS deck cannot be operated.
TV broadcasts cannot be recorded.
● The VHS deck is not selected.
]Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS
on the remote so that the VHS lamp lights up on the unit.
● “L-1” or “F-1” has been selected as the input mode.
]Set to the desired channel.
Camcorder recording is not possible.
The tape will not rewind or fast-forward.
● The camcorder has not been properly connected.
]Confirm that the camcorder is properly connected.
● The input mode is not correct.
● The tape is already fully rewound or fast-forwarded.
]Check the cassette.
]Set the input mode to “F-1”. (੬ pg. 75)
The playback picture does not appear while the tape is running.
Recording (VHS Deck)
● The TV receiver’s channel selector is not set to the video
channel.
]If you are using the RF connection, set the TV receiver to the
video channel.
]If you are using the AV connection, the TV receiver is not set to
the AV mode.
During recording, the tape does not run. The VHS recording lamp
lights up on the unit.
● The unit is in the Record Pause mode.
Press 4 to resume recording.
● The unit’s video channel has not been correctly set.
]Perform the video channel set. (੬ pg. 19)
Recording cannot be done.
● There is no cassette loaded, or the cassette loaded has had its
record safety tab removed.
]Insert a cassette, or using adhesive tape, cover the hole where
the tab was removed.
Noise appears during visual search.
● This is normal.
Noise appears during normal playback.
TV broadcasts cannot be recorded.
● The automatic tracking mode is engaged.
]Try manual tracking. (੬ pg. 52)
● “L-1” or “F-1” has been selected as the input mode.
]Set to the desired channel.
The playback picture is blurred or interrupted while TV
broadcasts are clear or “USE CLEANING CASSETTE” message
appears on the screen.
Camcorder recording is not possible.
● The camcorder has not been properly connected.
]Confirm that the camcorder is properly connected.
● The input mode is not correct.
● The video heads may be dirty.
]Use a dry cleaning cassette TCL-3F, or consult your JVC dealer.
]Set the input mode to “F-1”.
Breaks are noticeable in Hi-Fi soundtrack.
The tape is automatically rewound, then the unit is shut off.
● The automatic tracking mode is engaged.
]Try manual tracking. (੬ pg. 52)
● The end of the tape was reached during recording.
]The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
The desired program cannot be recorded.
Timer Recording (HDD & DVD Deck)
● The channel position does not correspond to that in the
receiving area.
Timer programming cannot be made.
]Set the correct channel position for the receiving broadcast.
(੬ pg. 23)
● Date and time is not correct.
]Set date and time correctly. (੬ pg. 22)
● Timer recording is in progress.
Recording cannot be made.
]Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
● No disc or a disc not being compatible with the unit is loaded.
]Load a recordable disc on the unit. (੬ pg. 7)
● The disc loaded is not formatted.
]Format the disc. (੬ pg. 87)
]Recording cannot be made on finalized discs. Load a recordable
disc on the unit.
recorded.
]Clear unnecessary titles on the disc or load a blank disc.
(੬ pg. 65)
● The DVD-RAM disc loaded has had its protect tab slid to the
protect position.
Timer programming recording does not start.
● Date and time is not correct.
]Set date and time correctly. (੬ pg. 22)
VCR Plus+ Timer Programming cannot be made.
● Date and time set on the unit is not correct.
]Set date and time correctly. (੬ pg. 22)
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(੬ pg. 23)
]Release the protect tab. (੬ pg. 10)
The VCR Plus+ system does not timer-record properly.
● The unit’s channel positions have been set incorrectly.
®
]Refer to “Changing VCR Plus+ Setting” (੬ pg. 86) and
reperform the procedure.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
91
Automatic Satellite Program Recording does not start.
The VCR Plus+ system does not timer-record properly.
]Connect the DBS receiver to the [VIDEO/AUDIO INPUT L1]
connectors properly. (੬ pg. 59)
● The unit’s channel positions have been set incorrectly.
]Refer to “Changing VCR Plus+ Setting” (੬ pg. 86) and
reperform the procedure.
®
On the front display panel, “– –:– –” appears.
Other Problems
● Power failure occurred.
The image of the TV broadcast appears distorted on the TV
screen.
“PROGRAM FULL” appears on the TV screen during timer
programming.
For RF/AV/S-video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
● 32 programs have already been timer programmed.
]Clear unnecessary programs on the unit, then try timer
programming again. (੬ pg. 58)
Video output indicator ( ) lights off on the front display panel.
For component video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights up on the front display panel.
cleared.
Whistling or howling is heard from the TV during camcorder
recording.
● The PC’s data recorded on a DVD-RAM drive cannot be cleared
on this unit.
]Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (੬ pg. 11, 87)
● The camcorder’s microphone is too close to the TV.
]Position the camcorder so its microphone is away from the TV.
● The TV’s volume is too high.
]Turn the TV’s volume down.
Timer Recording (VHS Deck)
When scanning channels, some of them are skipped over.
Timer programming cannot be made.
● Those channels have been designated to be skipped.
]If you need the skipped channels, restore them. (੬ pg. 23)
● Date and time is not correct.
]Set date and time correctly. (੬ pg. 22)
● The timer is not engaged.
]Press VHS TIMER and confirm that the VHS timer indicator
lights up on the front panel display.
● Timer recording is in progress.
The channel cannot be changed.
● Recording or Live Memory recording* is in progress.
]Press 9 to pause the recording, change channels, then press 4
to resume recording.
]Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
Channel settings that were made manually seem to have
changed or disappeared.
Timer programming recording does not start.
● Date and time is not correct.
]Set date and time correctly. (੬ pg. 22)
● The timer is not engaged.
]Press VHS TIMER and confirm that the VHS timer indicator
lights up on the front panel display.
● After the manual settings were made, Auto Channel Set was
performed.
]Perform “Manual Clock Set” (੬ pg. 22).
the clock is incorrect.
The VHS recording lamp on the unit won’t stop blinking.
● The clock setting data received from the host channel is
incorrect.
]Select a different host channel during “Semiauto Clock Set”
(੬ pg. 22), or perform “Manual Clock Set” (੬ pg. 22).
● The timer is engaged but there’s no cassette loaded.
]Load a cassette with the record safety tab intact.
● The loaded cassette has had its record safety tab removed.
]Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
Malfunction occurs and the unit cannot be power off.
]Reset the unit by disconnecting the AC power plug from the AC
The tape is automatically ejected, then the unit is shut off.
outlet and connect again.
● The end of the tape was reached during timer recording.
]The program may not have been recorded in its entirety.
Next time make sure you have enough time on the tape to
record the entire program.
● The end of the tape was reached during Instant Timer
Recording.
time make sure you have enough time on the tape to record the
entire program.
VCR Plus+ Timer Programming cannot be made.
● Date and time set on the unit is not correct.
]Set date and time correctly. (੬ pg. 22)
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(੬ pg. 23)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
92
CAN NOT FINALIZE THIS DISC
● Finalizing is not complete since the disc may be dirty or
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC?
CAN NOT CANCEL FINALIZATION
OF THIS DISC
● A disc that is not registered in the library has been inserted.
Register the disc as necessary. (੬ pg. 68)
● Canceling disc finalization is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry.
(੬ pg. 11, 88)
INSERT DISC XXXX
● Appears when a title that has been selected in the library is not
contained in the loaded disc.
PRESS [STOP] AGAIN TO STOP RECORDING
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
● During Live Memory playback, 8 has been pressed. (੬ pg. 48)
TIMER RECORDING COMPLETED
● The number of titles exceeds 99.
● The number of play lists exceeds 999.
● Timer recording has finished during Live Memory playback.
PLAYBACK WILL STOP
SET CLOCK BEFORE TIMER PROGRAMMING
THEN TIMER RECORDING WILL START
● To set the timer program, the clock must be set in advance.
(੬ pg. 22)
● Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
PROGRAM FULL
DELETE UNWANTED TIMER PROGRAMS
COPY PROHIBITED
CAN NOT RECORD
programs. To program more, you need to cancel a timer
program already set. (੬ pg. 58)
● An attempt has been made to record copy-protected contents.
● An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
DISC NOT LOADED
COPY PROHIBITED
CAN NOT PLAY
loaded upside down. (੬ pg. 10)
● The unit has detected invalid contents at the start or in the
middle of playback.
DISC NOT RECORDABLE
INSERT RECORDABLE DISC
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY
AND POWERED ON
● When a playback-only disc or a finalized disc is loaded, 7 has
been pressed. (੬ pg. 7)
● An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
● Check the connection. (੬ pg. 74)
PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY
● An invalid PlusCode number has been input. (੬ pg. 55)
GUIDE CHANNEL IS NOT SET
SET GUIDE CHANNEL THEN RETRY
● To set the timer program using the VCR Plus+ system, the
Guide Channel Number must be set in advance. (੬ pg. 86)
CAN NOT SET VCR PLUS TIMER PROGRAMMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
● Appears when you tried to input a PlusCode number during
timer recording or instant timer recording.
REGION CODE ERROR
CHECK DISC
● A disc loaded cannot be played back on this unit since the
(੬ pg. 8)
UNREADABLE DISC
CHECK DISC
(੬ pg. 8)
COULD NOT FORMAT THE DISC
CHECK THE DISC
● Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (੬ pg. 11, 87)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
EN
93
GENERAL
VIDEO/AUDIO (VHS Deck)
Signal system
NTSC color signal and EIA monochrome signal, 525 lines/60 fields
Recording system
DA4 (Double Azimuth) head helical scan system
Format
VHS NTSC standard
Power requirement
AC 120 Vd, 60 Hz
Power consumption
Power on: 49 W
Power off: 16.2 W
Temperature
Operating: 5°C to 35°C (41°F to 95°F)
Storage: –20°C to 60°C (–4°F to 140°F)
Operating position
Maximum recording time
(SP): 210 min. with ST-210 video cassette
(EP): 630 min. with ST-210 video cassette
Signal-to-noise ratio
Horizontal only
Dimensions (WxHxD)
435 mm x 96 mm x 383 mm (17-3/16" x 3-4/5" x 15-1/13")
Weight
6.7 kg (14.8 lbs)
Input/Output
Video input: 0.5 – 2.0 Vp-p, 75 C (pin jack)
Audio input:
45 dB
Horizontal resolution
230 lines
Frequency range
(Normal audio): 70 Hz to 10,000 Hz
(Hi-Fi audio): 20 Hz to 20,000 Hz
–8 dB, 50 kC (pin jack)
Corresponding to mono (left)
Audio output: –8 dB, 1 kC (pin jack)
RCA connectors:
Specifications shown are for SP mode unless otherwise specified.
TUNER/TIMER
IN x 3, OUT x 2
Tuning system
Frequency synthesized tuner
Channel coverage
VHF: Channels 2 – 13
UHF: Channels 14 – 69
CATV: 113 Channels
Input/Output (HDD & DVD Deck Only)
S-video input:
Y: 0.8 – 1.2 Vp-p, 75 C
C: 0.2 – 0.4 Vp-p, 75 C
S-video output:
Y: 1.0 Vp-p, 75 C
C: 0.3 Vp-p, 75 C
i.Link: 4-pin for DV input
Component video output:
Y: 1.0 Vp-p, 75 C
RF output
Channel 3 or 4 (Switchable; preset to Channel 3 when shipped)
75 C, unbalanced
Memory backup time
Approx. 60 minutes
CB/CR, PB/PR: 0.7 Vp-p, 75 C
Corresponding to copy protection
Cable Box: R3.5mm
ACCESSORIES
Provided accessories
RF cable x 1,
Digital audio output:
Optical: –18 dBm, 660 nm
Coaxial: 0.7 Vp-p, 75 C
Corresponding to Dolby Digital and DTS Digital Surround
Bit stream
Audio/Video cable,
Satellite Controller,
Infrared remote control unit,
“AA” battery x 2
Selectable in digital audio output setting menu
E.& O.E. Design and specifications subject to change without
notice.
VIDEO/AUDIO (DVD Deck)
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP): Approx. 1 hour
(SP): Approx. 2 hours
(LP): Approx. 4 hours
ATTENTION:
This unit contains microcomputers. External electronic noise or
interference could cause malfunctioning. In such cases, switch the
unit off and unplug the AC power cord. Then plug it in again and turn
the unit on. Take out the disc. After checking the disc, operate the
unit as usual.
(EP): Approx. 6 hours
(FR): Approx. 1 hour – 8 hours
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression system
MPEG2 (CBR/VBR)
VIDEO/AUDIO (HDD Deck)
Video recording compression system
MPEG2 (VBR)
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Recording time
Maximum 147 hours (with 80 GB HDD)
(XP): Approx. 18 hours
(SP): Approx. 35 hours
(LP): Approx. 70 hours
(EP): Approx. 105 hours
(FR): Approx. 18 – 147 hours
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
EN
94
Language Code List
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
Afar
IK
Inupiak
RN
RO
RU
RW
SA
SD
SG
SH
SI
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Abkhazian
Afrikaans
Ameharic
Arabic
IN
Indonesian
Icelandic
Hebrew
IS
IW
JI
Yiddish
Assamese
Aymara
Azerbaijani
Bashkir
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
Javanese
Georgian
Kazakh
Sangho
Serbo-Croatian
Singhalese
Slovak
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Byelorussian
Bulgarian
Bihari
SK
SL
Slovenian
Samoan
Shona
SM
SN
SO
SQ
SR
SS
ST
SU
SW
TA
Bislama
Bengali, Bangla
Tibetan
BN
BO
BR
CA
CO
CS
CY
DZ
EL
EO
ET
EU
FA
Somali
Kirghiz
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Breton
Latin
Catalan
Corsican
Czech
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Welsh
LV
Bhutani
Greek
MG
MI
TE
TG
TH
TI
Telugu
Esperanto
Estonian
Basque
Persian
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
OC
OM
OR
PA
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
TK
TL
FJ
Fiji
FO
FY
GA
GD
GL
GN
GU
HA
HI
Faroese
Frisian
Malay (MAY)
Maltese
TN
TO
TR
TS
TT
Irish
Burmese
Nauru
Turkish
Tsonga
Tatar
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Nepali
Occitan
TW
UK
UR
UZ
VI
Twi
(Afan) Oromo
Oriya
Ukrainian
Urdu
Hindi
Panjabi
Uzbek
HR
HU
HY
IA
Croatian
Hungarian
Armenian
Interlingua
Interlingue
PL
PS
PT
QU
RM
Polish
Vietnamese
Volapuk
Wolof
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
VO
WO
XH
YO
ZU
Xhosa
IE
Yoruba
Zulu
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
EN
95
Country/Area Code List for Parental Lock
AD
AE
AF
AG
AI
Andorra
CK
Cook Islands
Chile
GN
GP
GQ
GR
GS
Guinea
United Arab Emirates
Afghanistan
CL
Guadeloupe
CM
CN
CO
Cameroon
China
Equatorial Guinea
Greece
Antigua and Barbuda
Anguilla
Colombia
South Georgia and the South
Sandwich Islands
AL
Albania
CR
CU
CV
CX
CY
CZ
Costa Rica
Cuba
GT
GU
GW
GY
HK
HM
Guatemala
Guam
AM
AN
AO
AQ
AR
Armenia
Netherlands Antilles
Angola
Cape Verde
Christmas Island
Cyprus
Guinea-Bissau
Guyana
Antarctica
Argentina
Hong Kong
Czech Republic
Heard Island and McDonald
Islands
AS
AT
American Samoa
Austria
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
ER
ES
ET
FI
Germany
Djibouti
HN
HR
HT
HU
ID
Honduras
Croatia
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
Australia
Denmark
Dominica
Dominican Republic
Algeria
Haiti
Aruba
Hungary
Azerbaijan
Bosnia and Herzegovina
Barbados
Indonesia
IE
Ireland
Ecuador
IL
Israel
Bangladesh
Belgium
Estonia
IN
India
Egypt
IO
IQ
IR
British Indian Ocean Territory
Burkina Faso
Bulgaria
Western Sahara
Eritrea
Iraq
Iran (Islamic Republic of)
Bahrain
Spain
IS
Iceland
Italy
Burundi
Ethiopia
IT
BJ
Benin
Finland
JM
JO
JP
KE
Jamaica
Jordan
Japan
Kenya
BM
BN
BO
Bermuda
FJ
Fiji
Brunei Darussalam
Bolivia
FK
FM
Falkland Islands (Malvinas)
Micronesia
(Federated States of)
BR
BS
BT
BV
BW
BY
Brazil
FO
FR
FX
GA
GB
GD
Faroe Islands
France
KG
KH
KI
Kyrgyzstan
Cambodia
Bahamas
Bhutan
France, Metropolitan
Gabon
Kiribati
Bouvet Island
Botswana
Belarus
KM
KN
KP
Comoros
United Kingdom
Grenada
Saint Kitts and Nevis
Korea, Democratic People’s
Republic of
BZ
CA
CC
CF
CG
Belize
GE
GF
GH
GI
Georgia
KR
KW
KY
KZ
LA
Korea, Republic of
Kuwait
Canada
French Guiana
Ghana
Cocos (Keeling) Islands
Central African Republic
Congo
Cayman Islands
Kazakhstan
Gibraltar
GL
Greenland
Lao People’s Democratic
Republic
CH
CI
Switzerland
Côte d’Ivoire
GM
Gambia
LB
Lebanon
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
EN
96
LC
LI
Saint Lucia
NU
NZ
OM
PA
Niue
SZ
TC
TD
TF
TG
TH
TJ
Swaziland
Liechtenstein
Sri Lanka
New Zealand
Oman
Turks and Caicos Islands
Chad
LK
LR
LS
Liberia
Panama
French Southern Territories
Togo
Lesotho
PE
PF
PG
PH
PK
PL
Peru
LT
Lithuania
French Polynesia
Papua New Guinea
Philippines
Pakistan
Thailand
LU
LV
Luxembourg
Latvia
Tajikistan
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UM
Tokelau
LY
Libyan Arab Jamahiriya
Morocco
Turkmenistan
Tunisia
MA
MC
MD
MG
MH
ML
MM
MN
MO
MP
MQ
Poland
Monaco
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
Saint Pierre and Miquelon
Pitcairn
Tonga
Moldova, Republic of
Madagascar
Marshall Islands
Mali
East Timor
Turkey
Puerto Rico
Portugal
Trinidad and Tobago
Tuvalu
Palau
Myanmar
Paraguay
Taiwan
Mongolia
Qatar
Tanzania, United Republic of
Ukraine
Macau
Réunion
Northern Mariana Islands
Martinique
Romania
Uganda
Russian Federation
United States Minor Outlying
Islands
MR
MS
MT
MU
MV
Mauritania
Montserrat
Malta
RW
SA
SB
SC
SD
Rwanda
US
UY
UZ
VA
VC
United States
Saudi Arabia
Solomon Islands
Seychelles
Sudan
Uruguay
Uzbekistan
Mauritius
Maldives
Vatican City State (Holy See)
Saint Vincent and the
Grenadines
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
Malawi
SE
SG
SH
SI
Sweden
VE
VG
VI
Venezuela
Mexico
Singapore
Virgin Islands (British)
Virgin Islands (U.S.)
Viet Nam
Malaysia
Mozambique
Namibia
Saint Helena
Slovenia
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
SJ
Svalbard and Jan Mayen
Slovakia
Vanuatu
New Caledonia
Niger
SK
SL
SM
SN
SO
SR
ST
SV
SY
Wallis and Futuna Islands
Samoa
Sierra Leone
San Marino
Norfolk Island
Nigeria
Yemen
Senegal
Mayotte
Nicaragua
Netherlands
Norway
Somalia
Yugoslavia
South Africa
Zambia
NL
Suriname
NO
NP
NR
Sao Tome and Principe
El Salvador
Nepal
Zaire
Nauru
Syrian Arab Republic
Zimbabwe
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF TERMS
EN
97
A
O
A-B Repeat Playback ................................................ 37
Accidental erasure prevention .................................... 54
Adjusting The Picture Quality ..................................... 38
Angle Selection ........................................................ 30
Audio Channel Selection ........................................... 31
Audio Language/Sound Selection ............................... 31
Auto Channel Set ..................................................... 23
Auto Daylight Saving Time ........................................ 22
P
Pan&Scan ................................................................ 26
Play List ................................................................... 66
Program Playback .................................................... 39
Progressive scan ...................................................... 83
C
Cancel And Change Programs ..............................58, 62
Check Programs ..................................................58, 62
Country/Area Code List for Parental Lock .................... 95
R
D
Random Playback ..................................................... 39
Recordable/playable discs ........................................... 7
Recording Mode ................................................. 41, 44
Region Number .......................................................... 8
Resume Function ..................................................... 29
Disc menu ............................................................... 28
Discs For Playback Only ............................................. 8
DVD menu ............................................................... 28
E
Elapsed Recording Time Indication ................. 42, 45, 54
F
File Structure Of Discs ................................................ 9
SAP .............................................................43, 45, 54
Simulated Surround Effect ......................................... 38
Slow Motion ..................................................29, 46, 51
Soundtrack Selection ................................................ 52
G
Guide Program Number ............................................ 86
H
High-Speed Search ....................................... 28, 46, 51
I
Index Search ............................................................ 51
Instant Timer Recording (ITR) ......................... 42, 45, 54
Interlaced scan ......................................................... 83
J
Jump Search ............................................................ 49
T
Tape Position Indicator .............................................. 18
Tape Remaining Time ............................................... 54
L
Language Code List .................................................. 94
Letter Box ................................................................ 26
Live Memory .......................................................32, 47
Live Memory Recording ............................................ 49
U
M
Unplayable Discs ........................................................ 8
Usable cassettes ...................................................... 50
Manual Channel Set ................................................. 23
Manual Clock Set ..................................................... 22
Manual Tracking ....................................................... 52
Marking Positions To Play Back Again Later ................ 29
Menu/Audio/Subtitle Language Set ............................. 21
V
VHS Progressive Scan .............................................. 52
W
N
Weekly/Daily Recording ............................................ 56
When Programs Overlap Each Other .................... 58, 62
Next Function Memory .............................................. 52
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
EN
99
Download from Www.Somanuals.com. All Manuals Search And Download.
|
