JBL Car Amplifier GT5 A402 User Manual

GT5-A402  
OWNER’S MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GT5-A402 CAR AUDIO POWER AMPLIFIER OWNER’S MANUAL  
0
5
Installation Warnings and Tips  
• Disconnect the negative (–) lead from your vehicle’s  
battery.  
Speaker Output Connectors  
Power On LED  
• Illuminated when the amplifier is on.  
Protect LED  
• Connect the speakers to these terminals,  
observing proper polarity.  
6
• Two-channel operation: Connect the left  
speaker to the L+ and L– terminals and the  
right speaker to the R+ and R– terminals.  
• One-channel (bridged) operation: Connect the  
single speaker to the R+ and L– terminals.  
• Minimum speaker impedance for 2-channel  
operation is 2 ohms. Minimum speaker impedance  
for 1-channel (bridged) operation is 4 ohms.  
Fuse  
• Illuminated under any of the following fault  
conditions: battery over/under voltage, short  
circuit in speaker wires, amplifier is too hot,  
amplifier’s output circuit has failed (DC voltage  
is present in the amplifier’s output).  
Crossover-Frequency Control  
• At the installation sites, locate and make a note of  
all fuel lines, hydraulic brake lines, vacuum lines  
and electrical wiring. Use extreme caution when  
cutting or drilling in and around these areas.  
• Choose a safe mounting location away from moisture.  
• Make sure there is sufficient air circulation at the  
mounting location for the amplifier to cool itself.  
• Mount the amplifier, using the supplied hardware.  
7
8
• 12dB/octave crossover, variable from  
32Hz to 320Hz.  
B
• See for the adjustment procedure.  
1
2
• Replace only with the same type and rating.  
Power Input Connectors  
Crossover-Filter Selector  
• LP: Select for subwoofer(s).  
• FLAT: Select for full-range speakers when  
no subwoofer will be used in the system.  
• HP: Select for midrange speakers or  
full-range speakers when a subwoofer is  
used in the system.  
Specifications  
• 40W RMS x 2 @ 4 ohms and 1% THD + N*  
• 60W RMS x 2 @ 2 ohms,  
14.4V supply and 1% THD + N*  
• 120W RMS x 1 @ 4 ohms,  
14.4V supply and 1% THD + N*  
• Total peak power: 240 watts  
• Frequency response: 10Hz – 100kHz (–3dB)*  
• Maximum input signal: 6V*  
• Maximum sensitivity: 200mV*  
• THD + N: 0.05%  
• Signal-to-noise ratio: 85dBA  
(reference 1W into 4 ohms)*  
• Signal-to-noise ratio: 101dBA  
(reference rated power into 4 ohms)  
* CEA-2006A-compliant  
• +12V: Connect to the positive terminal of the  
vehicle’s battery. 10 AWG wire is recommended.  
Install an appropriate fuse holder and fuse (15A  
minimum) within 18 inches of the battery. Make  
sure the wire is not damaged or pinched during  
installation. Install protective grommets when  
routing wires through the firewall or other sheet  
metal.  
9
A
Bass-Boost Control  
• Provides 6dB of boost at 50Hz. Set the Bass-  
Boost control according to your preference,  
being careful not to apply enough boost to  
damage the speaker(s).  
• GND: Connect to the vehicle’s chassis. Refer to  
the picture below.  
Setting Input Level  
Factory Bolt  
Ring Connector  
A Turn Input-Level control counterclockwise to  
Ground Wire  
6V (minimum).  
B With a dynamic music track playing, turn the  
head unit’s volume control to the 3/4 position.  
C Turn Input-Level control clockwise until the  
music is so loud that it no longer sounds clear  
(distortion is present in the output).  
D Turn Input-Level control counterclockwise  
gradually, just until the music sounds clear,  
once again.  
E Input level is now adjusted correctly.  
Setting the Crossover  
A Crossover setting for 5" or larger full-range  
speakers when no subwoofer is included in  
the system.  
B Crossover setting for midrange and/or  
full-range speakers when a subwoofer  
is included in the system.  
C Crossover setting for subwoofers.  
Note: Acceptable frequency ranges are indicated  
in gray.  
Note: Remove any paint  
below ring connector.  
Star Washer  
• REM: Connect to the “Remote Out” lead from  
the source unit or to a source of switched  
12V+ (ACC).  
Input Connectors (RCA)  
• Connect to the RCA outputs from the source unit  
B
3
4
or signal processor.  
Input-Level Control  
• Used to match the input level of the amplifier  
to the output level of the source unit.  
A
• See  
for the adjustment procedure.  
This product is designed for mobile applications and is not  
intended for connection to the mains.  
A valid serial number is required for warranty coverage.  
Features, specifications and appearance are subject to change  
without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Declaration of Conformity  
We, Harman Consumer Group, Inc.  
2, route de Tours  
72500 Château du Loir  
France  
Harman Consumer Group, Inc.  
250 Crossways Park Drive, Woodbury, NY 11797  
declare in own responsibility that the product described in this owner’s  
manual is in compliance with technical standards:  
EN 55013:2001+A1:2003  
© 2008 Harman International Industries, Incorporated. All rights reserved.  
JBL is a trademark of Harman International Industries, Incorporated,  
registered in the United States and/or other countries.  
EN 55020:2002+A1:2003  
Klaus Lebherz  
Harman Consumer Group, Inc.  
Château du Loir, France 3/08  
Part No. GT5A402OM 3/08  
www.jbl.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Washer Dryer pwdc User Manual
Initio Network Card INI 9100U User Manual
Insignia Speaker System NS 5648 User Manual
InSinkErator Garbage Disposal AS 101K User Manual
JL Audio Car Speaker SB GM HUMR2 12W6v2 User Manual
Kalorik Work Light PPG 40738 User Manual
Karcher Pressure Washer K 27 User Manual
KitchenAid Refrigerator Overlay Model Refrigerator User Manual
KitchenAid Ventilation Hood KWCU265HBT1 User Manual
Kodak Battery Charger KP100 User Manual