®
Stealthbox
I N S T A L L A T I O N G U I D E
START
HERE
for the
SB-D-DRNGO/10WØ
(Fits 1997-2001 Dodge Durango, models
with three seating rows only)
➔
➔
➔
STEP 1: Unbolt the second row of seating
from the vehicle and remove as single unit.
STEP 2: Remove the black plastic covers
from each side of the armrest, of the center
seat.
STEP 3: Remove the fourTorx bolts that
attaches the armrest to the center seat.
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation. Several of the steps in this
process may require two people to
accomplish.
➔
➔
➔
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1)The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
STEP 4: Lift off the armrest.
STEP 5: Remove the upholstery from the
lower center seat by releasing the four plastic
clips holding it in place.
STEP 7: Measure 2 1/4" from the front lip of
the center seat structure side bars. Make a
mark at the 2 1/4" measurement.
STEP 6: Remove the upholstery and foam
from the seat frame to expose the metal grid
structure.
STEP 8: Drill a 5/16" hole centered left to
right in each side bar at the 2 1/4" mark.
Please enjoy your JL Audio Stealthbox
responsibly.
Continued on Next Page ➔
SB-D-DRNGO/10WØ, JL AUDIO, Inc 2004
Page 1
Sheet SKU#011103 Revision 6/28/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Previous
Page
CONGRATULATIONS!
INSTALL COMPLETE.
➔
➔
➔
➔
Included Hardware:
(4) 1/4" x 2" Bolts
(4) 1/4" Washers
(4) #8 Flat Head Screws
(4) 1/4" Lock Washers
(1) Console Insert
STEP 13: Attach the plastic clips on the
Stealthbox upholstery to the bars under the
seat structure.
STEP 14: Run speaker wire from the amplifi-
er to the Stealthbox mounting location. Be
sure the wires are routed in such a way that
they will not be pinched when the seat is rein-
stalled.
STEP 15: Place the seat back in the vehicle
and connect the speaker wires to the
Stealthbox.
Do not overstretch the upholstery
STEP 16: Bolt the seat in place in the
reverse order that it was removed.
Difficulty Of Installation:
Mid/High Frequency Driver Information:
Specifications:
Enclosure Type: Acoustical Suspension (sealed)
Driver Type: 10WØ
Nominal Impedance: 4Ω
Cont. Power Handling: 125Watts
Front Location Driver Size:
6.5”
VR650-CSI
Applicable JL Audio Products:
TR,VR,XR,ZR 650-CSI
JLAudio recommends using a high quality amplifier such as the JLAudio e2150. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the e2150 when being used to power your Stealthbox®.
Rear Location Driver Size :
5.25”
Applicable JL Audio Products:
TR,VR,XR 650-CXI
TR525-CXI
The JL Audio e2150 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
10369 N. Commerce Pkwy, Miramar, Florida 33025-392
Phone: 954.443.1100
Fax: 954.443.1111
SB-D-DRNGO/10WØ, JL AUDIO, Inc 2004
Page 3
Sheet SKU#011103 Revision 6/28/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|