PORTABLE PA
USER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
15. Service Instruction in Owner’s Manual: “CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR
USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.”
16. To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from
the AC receptacle.
17. “WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC – SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.”
18. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as
vases, are placed on the equipment.
19. The mains plug of the power supply cord shall remain readily operable.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
EON 206P systems may be cleaned with a dry cloth. Do not get moisture into any of the openings in the system.
Ensure that the system is unplugged from the AC outlet before cleaning.
THIS APPARATUS CONTAINS POTENTIALLY LETHAL VOLTAGES. TO PREVENT ELECTRIC SHOCK OR
HAZARD, DO NOT REMOVE CHASSIS, MIXER MODULE OR AC INPUT COVERS. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Precautions
The EON 206P PA system covered by this manual is not intended for use in high
moisture environments. Moisture can damage the speaker cone and surround and cause
corrosion of electrical contacts and metal parts. Avoid exposing the speakers to direct
moisture. Keep speakers out of extended or intense direct sunlight. The driver suspension
will prematurely dry out and finished surfaces may be degraded by long-term exposure
to intense ultra-violet (UV) light. The EON 206P PA system can generate considerable
energy. When placed on a slippery surface such as polished wood or linoleum, the
speaker may move due to its acoustical energy output. Precautions should be taken to
assure that the speaker does not fall off a stage or table on which it is placed.
!
Stand Mounting Safety Precautions
The EON 206P speakers contain a 36 mm receptacle cup to allow mounting on tripod stands or on a pole over
subwoofers. When using stands or poles, be sure to observe the following precautions:
• Check the stand or pole specification to be certain the device is designed to support the weight of the
speaker. Observe all safety precautions specified by the manufacturer.
• Always verify that the stand (or subwoofer/pole) is placed on a flat, level and stable surface and
be sure to fully extend the legs of tripod type stands. Position the stand so that the legs do not
present a trip hazard.
• Route cables so that performers, production crew, and audience will not trip and topple the
speakers over.
• Inspect the stand (or pole and associated hardware) before each use and do not use equipment with
worn, damaged or missing parts.
• Do not attempt to place more than one EON 206P series speaker on a stand or pole.
• Always be cautious in windy, outdoor conditions. It may be necessary to place additional weight (i.e.
sandbags) on the base of the stand to improve stability. Avoid attaching banners or similar items to
any part of a speaker system. Such attachments could act as a sail and topple the system.
• Unless you are confident that you can handle the weight of the speaker, ask another person to help
you get it onto the tripod stand or pole.
Hearing Damage, Prolonged Exposure To Excessive SPL
The EON 206P system is capable of generating sound pressure levels (SPL) sufficient to cause permanent
hearing damage to performers, production crew and audience members. Caution should be taken to avoid
prolonged exposure to SPL in excess of 90 dB.
WATCH FOR THESE SYMBOLS!
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (Servicing) instructions in the literature
accompanying the product.
WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
The lightning flash with the arrowhead symbol within an
equilateral triangle is intended to alert the user to the presence
of un-insulated “Dangerous Voltage” within the products
enclusure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: EON 206P PA System Declaration of Conformity
This equipment complies with the EMC directive 89/336/EEC
Modified by
92/31/EEC
93/68/EEC
98/13/EEC and LVD 73/23/EEC modified by 93/68/EEC
This product meets safety standards:
EN60065:2002
UL6500 7th Edition: 2003
UL 60065 - STANDARD FOR AUDIO, VIDEO AND SIMILAR ELECTRONIC
APPARATUS - SAFETY EQUIREMENTS - Edition 7 - Revision Date 2007/12/11
CSA C22.2 NO 60065-03 - AUDIO, VIDEO AND SIMILAR ELECTRONIC
APPARATUS – SAFETY REQUIREMENTS - Edition 1 - Revision Date 2006/04/01
IEC 60065 - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS -- SAFETY
REQUIREMENTS - Edition 7.1 - Issue Date 2005/12/01
And EMC Standards
EN55103-1 (E2)
EN55103-2 (E2)
FCC Compliance Notice
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However there is no guarantee that the interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio and television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to collect the interference by one or more of the
following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Introduction To The EON 206P PA System
Thank you for choosing the JBL EON 206P PA system. The EON 206P is a self-contained, portable PA system
featuring multiple input channels with individual tone controls, reverb and convenient output routing capabilities
that allow the user to integrate the system into any number of audio environments. And with its lightweight and
ergonomic design the EON 206P is perfect for situations where ease and portability are just as important as
quality and flexibility.
Included in the EON 206P package are:
• 2 JBL professional speakers
• 1 center housing with powered mixer and compartment for storage of speaker cables
• 1 pair of unshielded speaker cables
• 1 power cable
• User’s guide
GETTING STARTED
1. Remove EON 206P system from the carton.
2. Detach speakers from center powered mixer section.
(1)
(2)
(3)
Press here
Slide button
Lift
3. If you have purchased speaker stands, you can
place the speakers on the stands utilizing the pole
mount adaptor built into the EON206P speaker cabinets.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Connect the Mixer Module to the Speakers
On the back side of the mixer you will notice two ¼" phone jacks – these are your speaker output jacks.
Take the speaker cables and connect them from these jacks to the jacks on the back of the speakers.
To Left speaker
L
R
To Right speaker
5) Connecting the AC Power Cable
Connect the female end of the power cable to the mixer and plug
the male end into the wall socket or extension cord. Turn the “MASTER VOLUME” control to “0”.
Now turn the power switch to the “on” position. You should see the “POWER” indicator illuminated.
At this point you are ready to bring in an audio signal and hear the signal amplified by the system.
AC power inlet
L
R
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Acquainted with the EON 206P Powered Mixer
This part of the EON 206P system houses the mixing board and power amplifier. You will connect all of the
microphones, musical instruments, external sound sources (like MP3 or CD players), in addition to any recording
devices or additional speakers like a personal monitor, subwoofer or “Front of House” feed.
The Basics
The mixing board is actually a very simple device. A “mixing board” brings audio sources “in” (through
the inputs) and routes the signal to the outputs (MASTER VOLUME/SPEAKER OUTPUTS or MONITOR
OUTPUTS). The mixer controls enable the user to affect the tone and/or volume in addition to routing the signal
and adding reverb to individual input sources.
POWER
POWER
TREBLE
TREBLE
TREBLE
TREBLE
LIMIT
BASS
BASS
LIMIT
REVERB
REVERB
BASS
BASS
ON
OFF
ON
OFF
MASTER
VOLUME
VOLUME
VOLUME
REVERB
REVERB
VOLUME
VOLUME
MIC
LINE
MIC
LINE
ON
OFF
ON
OFF
MASTER
VOLUME
L
L
R
R
CH 1
CH 2
CH 3/4
CH 5/6 MONITOR
OUT
VOLUME
VOLUME
VOLUME
VOLUME
MIC
LINE
MIC
LINE
L
L
JBL PROFESSIONAL
NORTHRIDGE, CA. USA
R
R
A
HARMAN INTERNATIONAL COMPANY
SERIAL NO:
CH 1
CH 2
CH 3/4
CH 5/6 MONITOR
OUT
DESIGNED AND ENGINEERED IN THE USA
Let’s look at the “inputs” first:
AUDIO INPUTS
The EON 206P has 6 inputs: 2 mono inputs and 2 stereo inputs.
All of the inputs will route to the speakers and to the MONITOR OUTPUT SECTION.
MONO MIC/LINE INPUTS
Moving from left to right there are 2 identical input strips comprised of (from top to bottom) a treble control,
bass control, reverb control, reverb on/off button, volume control, mic/line selector and a XLR 1/4"
combination conector.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Treble control adjusts the amount of high
frequencies on the particular channel
POWER
TREBLE
TREBLE
Bass control adjusts the amount of low
fequencies on the particular channel
LIMIT
BASS
BASS
Effect control adjusts the amount of
effect on the particular channel
REVERB
REVERB
ON
OFF
ON
OFF
MASTER
VOLUME
Channel Volume control adjusts the
gain on the particular channel
VOLUME
VOLUME
MIC/LINE “SELECTOR” allows you to
select between a microphone (XLR)
input and a line (1/4" phone) input
VOLUME
VOLUME
MIC
LINE
MIC
LINE
L
L
R
R
Combination 1/4" phone plug and
XLR male input
CH 1
CH 2
CH 3/4
CH 5/6 MONITOR
OUT
STEREO INPUTS
The EON 206P has two stereo inputs and these are used primarily for MP3 or CD players but could be used
with the stereo output of an electronic keyboard, instrument pre-amp or processor, or an electronic drum
machine. The inputs labeled “CH 3/4” offer the option of using ¼" phone plugs or RCA plugs and this channel
has a volume control. The input labeled “CH 5/6” is a 3.5 mm stereo input of the type typically found on
personal music players. This input does not have a volume control as personal music players usually have a
“volume control” built into the unit. This is the best way to control the volume of the unit plugged into
this input.
Volume Control for “STEREO IN 3/4”
VOLUME
Stereo in 3/4 RCA inputs
(use with MP3 Player,
CD or any consumer
type electronics)
L
Stereo in 3/4 1/4" Phone inputs
(use with electronic keyboard,
instrument pre-amp or processor or an
3.5 mm input jack for
“CH 5/6” for use with
personal music players
R
electronic drum machine)
CH 3/4
CH 5/6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEREO OUTPUTS: We’ve brought signals into the mixer now let’s send
them somewhere…The EON 206P has Left and Right 1/4" outputs:
1. LEFT/RIGHT speaker outputs -
These outputs should only be connected to the
EON 206P speakers and under no condition should
they be connected to the input of another electronic device.
These outputs carry power and as such could damage the
L
electronic device. Only use “unshielded” speaker cables
(like the cables provided with your EON 206P).
R
VOLUME
2. “MONITOR OUTPUTS”
These outputs allow you to route the stereo mixer signal to another
destination like a recording device, personal monitor, subwoofer
or to another PA system (Front of House).
L
R
MONITOR
OUT
POWER
LIMIT
MASTER VOLUME and “Limit” LED
Your EON 206P is equipped with a “Master Volume” that controls
the overall output volume of the system and a Yellow LED that
indicates that you have approached the maximum output.
MASTER
VOLUME
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: System Specifications
EON206P
System Type:
Powered mixer with 2 two-way bass-reflex enclosures
System
Maximum SPL Output:
Frequency Range (-10dB):
Frequency Response (-3dB):
AC input :
113 dB peak system output (pink noise)
64Hz – 22kHz
77Hz – 20kHz
100 - 120 VAC, 220-240 VAC 50/60 Hz
Amplifier
Design:
Class D
System Power Rating:
160 Watts (2 x 80 W)
Output Connector:
2 x 1/4" TS (unbalanced) amplifier outputs
Mixer
Input Connectors:
Channels
6 inputs (2 Mono Mic/Line, 2 x Stereo)
1-2 are XLR / 1/4" jack combo connectors
XLR is a mic level input, 1/4" is a line level input
3-4, one pair of 1/4" balanced TRS jacks (stereo), and a pair of RCA jacks (stereo)
5-6 is a 3.5 mm stereo jack
Input Impedance:
Ch 1-2 Combo: XLR 40 K Ohms Balanced
Ch 1-2 Combo: TRS 40 K Ohms Balanced
Ch 3-4: TRS 20 K Ohms Balanced
Ch 3-4: RCA 5 K Ohms Unbalanced
Ch 5-6: 3.5 mm 10 K Ohms Unbalanced
Output Connectors:
Signal Indicators:
Monitor outputs: one pair of RCA jacks (stereo)
Limit: Yellow LED indicates limiter active condition
EQ:
Individual channel Bass and Treble controls, center detent, +/-12 dB cut and boost
On Board DSP Limiting and Tuning
System Limiter:
Speaker
LF Driver:
HF Driver:
1 x JBL 326G 165 mm (6.5 in) woofer
1" neodymium black mylar dome tweeter
Coverage Pattern:
Crossover Frequency:
Crossover Type:
100º x 80º nominal
2.2 kHz
Passive network, 2nd order filters (-12 dB per octave)
for high pass and low pass filters
Enclosure:
Polypropylene
Suspension/ Mounting:
Handles:
36 mm pole socket
One on top
Grille:
Powder coated perforated steel
20.9” X 27.8” x 13.4” (530mm x 705mm x 340mm)
Shipping Package
Dimensions (H x W x D):
Net Weight of System:
11.38 kg (25 lbs)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Cables and Connectors
The standard cable for interconnection of microphone and
XLR/F to XLR/M Microphone Cable
line level signal in professional audio systems.
• Microphone to mixer
For connecting balanced devices with 1/4 inch phone and
maybe used interchangeably.
TRS (balanced) 1/4 inch phone jack to XLR/M
TRS (unbalanced) 1/4 inch phone jack to XLR/M
TS (unbalanced) 1/4 inch phone jack to XLR/M
XLR/M to RCA (phono) cable
For connections of instruments with unbalanced outputs
to balanced XLR inputs.
This cable is electrically identical to “TRS” (unbalanced)
1/4 inch phone and may be used interchangeably.
Connects consumer audio products and some DJ mixer
outputs to professional audio equipment inputs
Splits a stereo output into separate left/right signals.
TRS 1/4 inch Phone jack to dual 1/4 inch Phone jack
Change to a TRS mini-phone jack to connect to the output
of a portable. MP3/CD – player and computer sound cards
to a mixer.
TRS 1/4 inch Phone jack to dual 1/4 inch Phone jack
XLR/F to XLR/M audio ground lift
Only with balanced in - and outputs
XLT/F to XLR/M Audio Groud Lift
(no connection)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Contact Information
Mailing Address:
JBL Professional
8500 Balboa Blvd.
Northridge, CA 91329
Shipping Address:
JBL Professional
8500 Balboa Blvd., Dock 15
Northridge, CA 91329
(Do not return product to this address without first obtaining prior authorization from JBL)
Customer Service:
Monday through Friday
8:00am - 5:00pm
Pacific Coast Time in the U.S.A.
(800) 8JBLPRO (800.852.5776)
On The World Wide Web:
Professional Contacts, Outside the USA:
Contact the JBL Professional Distributor in your area. A complete list of JBL Professional international
Product Registration:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Warranty Information
The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for
five years from the date of the first consumer purchase. JBL amplifiers are warranted for three years from the
date of original purchase. Enclosures and all other JBL products are warranted for two years from the date of
original purchase.
Who Is Protected By This Warranty?
Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product
has been purchased in the Continental United States, Hawaii or Alaska. (This Warranty does not apply to JBL
products purchased elsewhere except for purchases by military outlets. Other purchasers should contact the
local JBL distributor for warranty information.); and B.) The original dated bill of sale is presented whenever
warranty service is required.
What Does The JBL Warranty Cover?
Except as specified below, your JBL Warranty covers all defects in material and workmanship. The following
are not covered: Damage caused by accident, misuse, abuse, product modification or neglect; damage
occurring during shipment; damage resulting from failure to follow instructions contained in your Instruction
Manual; damage resulting from the performance of repairs by someone not authorized by JBL; claims based
upon any misrepresentations by the seller; any JBL product on which the serial number has been defaced,
modified or removed.
Who Pays For What?
JBL will pay all labor and material expenses for all repairs covered by this warranty. Please be sure to save
the original shipping cartons because a charge will be made if replacement cartons are requested. Payment of
shipping charges is discussed in the next section of this warranty.
How To Obtain Warranty Performance
If your JBL product ever needs service, write or telephone us at JBL Incorporated (Attn: Customer Service
Department), 8500 Balboa Boulevard, PO. Box 2200, Northridge, California 91329 (818-893-8411). We may
direct you to an authorized JBL Service Agency or ask you to send your unit to the factory for repair. Either way,
you’ll need to present the original bill of sale to establish the date of purchase. Please do not ship your JBL
product to the factory without prior authorization. If transportation of your JBL product presents any unusual
difficulties, please advise us and we may make special arrangements with you. Otherwise, you are responsible
for transporting your product for repair or arranging for its transportation and for payment of any initial shipping
charges. However, we will pay the return shipping charges if repairs are covered by the warranty.
Limitation of Implied Warranties
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
EXCLUSION OF CERTAIN DAMAGES
JBL’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE
PRODUCT AND SHALL NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT
ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY, FROM STATE TO STATE.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number: 5001426
Download from Www.Somanuals.com. All Manuals Search And Download.
|