Owners Manual
LSR305
5" Powered
LSR308
8" Powered
LSR310 S
10" Powered
Studio Monitor
Studio Monitor
Studio Subwoofer
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
Explanation of Graphic Symbols
The exclamation point within an equilateral
triangle is intended to alert the users to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
The lightning flash with the arrowhead symbol,
within an equilateral triangle, is to alert the
user to the presence of insulated “dangerous
voltage” within the products enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to humans.
7. Do not block any ventilation openings. Install in
accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves or other apparatus
that produce heat.
CAUTION: TO REDUCE THE RISK
OF ELECTRONIC SHOCK - DO NOT
REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL. DO NOT EXPOSE
THIS APPARATUS TO RAIN OR MOISTURE.
9. Do not defeat the safety purpose of the grounding type
plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacle and the
point where the power cord connects to the apparatus.
Any changes or modifications not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
11. Only use attachments/accessories specified by
the manufacturer.
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
12. Unplug this apparatus during lightning storms or
when unused for long periods of time.
13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, including: power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
14. The appliance coupler of the power supply cord is used
as the ultimate disconnect device from the mains. The
appliance coupler shall remain readily operable.
Reorient or relocate the receiving antenna.
•
•
15. The apparatus shall be connected to mains socket outlet
with a protective earthing connection.
Increase the separation between the equipment
and receiver.
WARNING:
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•
•
To reduce the risk of fire or electrical shock, do not
expose the apparatus to rain or moisture.
•
Consult the dealer or an experienced radio/ TV
technician for help.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus. As with any electronic
product, use care not to spill liquids into any part of the
system. Liquids can cause a failure and/or a fire hazard.
•
CAN ICES-3(B)/NMB-3(B)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Safety Instructions ..................................................................................... 3
Introduction .............................................................................................................5-6
Setting Up Your System .............................................................................................. 6
What's Included?................................................................................................... 6
Unpacking.............................................................................................................. 6
Placement.............................................................................................................. 7
Audio Connections ................................................................................................ 8
Power Connections................................................................................................ 8
Making Sound........................................................................................................ 9
LSR305 and LSR308 Powered Studio Monitors
Front and Rear Views........................................................................................... 10
Input Panel........................................................................................................... 11
Audio Connections .............................................................................................. 11
LSR310S Powered Studio Subwoofer
Front and Rear View ........................................................................................... 12
Input Panel........................................................................................................... 13
Audio Connections .............................................................................................. 13
Setting Subwoofer Level ..................................................................................... 14
Placement and Polarity........................................................................................ 14
XLF, Extended Low Frequency Setting,
Crossover Settings and Bass Management ........................................................ 14
Surround Sound and .1 LFE Channel .................................................................. 15
Systems Connections .........................................................................................16-17
Trouble Shooting ........................................................................................................ 18
Specifications............................................................................................................. 19
JBL Service Contact Information.............................................................................. 20
Product Warranty Information ................................................................................. 21
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Introduction
Congratulations on your purchase of JBL Professional 3 Series Studio Monitors. These studio monitors and
Subwoofer meet JBL’s high standards for accuracy and long-term reliability in demanding professional
applications. All 3 Series models incorporate JBL Professional transducer and network technologies to provide
accurate frequency response, exceptional low frequency extension and high SPL capability. JBL LSR Linear
Spatial Reference design ensures greater accuracy at the mix position in acoustically varied work spaces and
production environments. Additionally, each speaker is equipped to interface with a range of signal
sources including high-output professional equipment.
JBL LSR Linear Spatial Reference Design
Because listening environments vary, JBL designed the 3 Series system using LSR Linear Spatial Reference
design criteria that improve accuracy at the listening position in a broad range of rooms. The key to accuracy is
ensuring not just the on-axis sound, but also the reflected sound reaching the mix position is neutral. While most
manufacturers take only a single on-axis measurement of the speaker’s performance, Linear Spatial Reference
design criteria requires 72 measurements, 360 degrees around the speaker, yielding 1,200 times more data. This
data is used in the design of critical system components, enabling JBL to engineer complete systems that deliver
smooth off-axis response. The result: clear accurate sound at the listening position in any room.
3-Series Image Control Waveguide
JBL’s revolutionary Image Control Waveguide gives the LSR305 and LSR308 remarkable imaging, a wide
sound-stage, and a solid “phantom center.” Subtle details can be heard, even in a dense mix. As an added
benefit, incorporating this waveguide, 3-Series models give you a broad “sweet-spot” in your work space,
so you don’t have to be seated directly in front of the speakers to hear accurate, natural and open sound.
3 Series models include a range of features to meet the needs of demanding audio production applications.
LSR305 and LSR308 models include:
• Low frequency magnetically-shielded transducers, equipped with 1.5" voice coils and robust motor structures to
provide excellent low frequency performance. By reducing thermal-related effects, the 3 Series Studio Monitors
and Subwoofer sound the same at low, medium and high levels. The woofers are magnetically shielded to prevent
interference with magnetically sensitive displays and equipment. The woofer’s self-repairing dust dome is resistant
to dents caused by fingers or external objects.
™
• JBL’s Patented Slip Stream low frequency port design that works in concert with the woofer to produce deep
bass response at all playback levels. The double-flared shape of the port is precisely engineered for greater low-
frequency extension and reduced turbulence.
• Bi-amplified Design with individual power amplifiers for the Low Frequency and High Frequency Transducers.
The design utilizes efficient high-output Class D integrated power amplifiers to provide high SPL
(Sound Pressure Level) for demanding production applications.
• Soft dome magnetically-shielded high-frequency transducers with optimally damped materials to improve
transient response and minimize distortion. By reducing distortion in the lower operating range, where the
ear is most sensitive, these transducers reduce ear fatigue.
• Balanced XLR and 1/4" connectors, a dented level attenuator to allow interface to a broad range of signal
sources. The +4 dB / -10 dB input sensitivity switch allows connection of the speakers to high-output
professional equipment without danger of input overload.
• High Frequency and Low Frequency Trim controls in the LSR308 and LSR305 allow adjustment of frequency
response to preference, or to compensate for acoustically reflective or absorptive listening environments.
Producing extended low frequency into the 20 Hz region, the LSR310S is the perfect match for the LSR305
and LSR308 Studio monitors. The LSR310S feature set includes:
• A custom designed down-firing, High-Excursion 10" woofer with an additional bucking magnet.
• 200 Watts Class D Power Amplifier with abundant output and dynamic headroom for the most
demanding production styles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Patented Slip Stream Port – The patented JBL low frequency port design works in concert with the
3 Series woofer for accurate bass response at all playback levels.
• A detented volume control makes it easy to balance of the LSR310S in your studio monitor system.
• Balanced XLR and 1/4" inputs and XLR outputs you can add the LSR310S to any studio monitor system
to extend its low frequency performance, or use it as the “.1” LFE Channel in a surround sound system.
• The -10 dBV/+4 dBu sensitivity switch ensures compatibility with a broad range of signal sources, allowing
you to connect the LSR310S to high-output professional equipment without any danger of input overload.
• Three Crossover settings: 80 Hz, XLF, External
• The 80 Hz setting implements high and low pass filters to create a seamless blend of the LSR310S with
JBL’s LSR305 or LSR308 studio monitors or models from other manufacturers.
• The external setting bypasses all filtering, allowing use of an external crossover.
• The special XLF setting activates a 120 Hz High Pass Filter in conjunction with a low frequency tuning
that approximates the tuning used in club playback systems. Using this setting, the bass output more
than doubles.
• A protective limiting circuit allows the subwoofer to operate continuously at full output without failure.
JBL Professional Reliability
Prior to becoming a production-ready design, each 3 Series model is subjected to JBL’s tough 100-hour power
test, in which the speaker is required to play continually at full output for 100 hours without failure. This demanding
test ensures your 3 Series speakers will deliver years of reliable performance. To get the most out of your JBL 3
Series, please review this owner’s manual and keep it on hand for future reference. Also, please register your new
Section 3: Setting Up Your System
Each 3 Series box includes the following items:
• One 3 Series Studio Monitor or Subwoofer
• One Power Cord
• Quick Set Up Guide
• LSR308 and LSR305 include peel-off rubber pads
UNPACkING
When removing a speaker from its packaging, we recommend the following procedure, which will prevent
damage of the high frequency transducer located near the top of the cabinet on the front of the speaker:
LSR305 and LSR308:
• Remove the outer shipping carton, if one exists.
• Place the inner carton on the floor with the top facing upwards.
• Open the top of the box.
• Without removing the internal packaging end-cap, gently rotate the carton so the open end
rests on the floor and the bottom of the carton is facing you.
• Gently lift the carton allowing the speaker and protective end-cap to slide out of the carton
and remain on the floor.
• Save the cartons and use the above procedure in reverse when you want to repack the
units for shipment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LSR310S Subwoofer - The subwoofer weighs 19 kg (42 lbs.) Unpacking the subwoofer does not require you lift the
subwoofer. However, you will need to rotate the subwoofer in the carton. If you are unable to perform the following
steps without assistance, please request help from another person.
• Remove the outer shipping carton, if one exists.
• Place the carton on the floor with the bottom facing upward.
• Open the bottom flaps of the carton and remove any protective packing materials from the bottom of the
subwoofer. Open the bag that protects subwoofer, exposing the subwoofer’s four feet.
• Gently rotate the carton so the bottom of the carton is facing the floor and the four feet of the subwoofer are
in contact with the floor.
• Gently lift the carton allowing the subwoofer and protective packing materials to slide out of the carton and
remain on the floor.
• Remove the protective packing materials and documentation from the top of the subwoofer. Save the
cartons and use the above procedure in reverse when you want to repack the units for shipment.
PLACEMENT
3 Series speakers are designed to deliver exceptional imaging in any room. To get the most out of your speakers,
follow these recommendations:
• Locate the four self-adhesive rubber pads supplied with LSR305 and LSR308 speakers. Position and attach
these to the bottom surface of the speaker close to each corner.
• Position each LSR305 and LSR308 speaker in a vertical orientation with the tweeter on the top.
Vertical orientation eliminates phase shift and cancellation of frequency response that occurs when the
distance of the woofer to the ear is different from the distance of the tweeter to the ear.
• Angle the speakers so the high-frequency transducer in each speaker is aimed directly towards the ear
of the listener.
• Ideally, LSR305 and LSR308 Series speakers should be placed on suitable speaker stands, rather than on
the work surface. This will reduce resonance and deterioration of low frequency performance that occurs
through the speaker’s mechanical coupling with the work surface.
• For optimum imaging, the left speaker and the right speaker should be placed symmetrically in the room,
so each speaker is the same distance from adjacent walls and reflective surfaces.
• The speakers should be placed so the position of the listener and the two speakers form an equilateral
triangle. Adjusting the distance between the speakers will affect the quality of bass heard at the listening
position. You can experiment with speaker placement to find the placement that produces the preferred
bass response, imaging and when listening to stereo material, produces a strong “phantom” center in
which vocals and some instruments seem to originate from a point between speakers.
• The listening distance can be determined according to your preference, the acoustics of your room and the
maximum SPL (Sound Pressure Level) you want to hear at the listening position. You can find the speaker’s
maximum SPL at 1 Meter in the Specifications Section at the end of this manual. Each doubling of listening
distance will reduce the SPL at the listening position by 6 dB in an acoustically absorptive room, but only 3
or 4 dB in an acoustically reflective room.
LSR310S Subwoofer placement: The low frequency driver of the 310S is mounted on the bottom panel of the
subwoofer. Before placing the subwoofer, make sure the position on the floor is free of any large objects that can
interfere with or damage the woofer. In a stereo system, The LSR310S Subwoofer should be placed directly on the
floor, located between the Left and Right Speakers. In a surround sound system, the subwoofer can be located
between the Left and Center or between the Right and Center channel Speakers. The distance of the subwoofer
from the listening position can be adjusted to produce the optimum balance of bass in the system. Placing the
subwoofer close to a wall or in a corner generally will increase the amount of bass heard in the room. Experiment to
determine the Subwoofer placement that produces the best balance and quality of bass in the system.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: LSR305 and LSR308 Powered Studio Monitors
SUB / LFE
CENTER
SUB / LFE
LEFT
RIGHT
LEFT
RIGHT
MIX POSITION
MIX POSITION
LEFT
SURROUND
RIGHT
SURROUND
AUDIO CONNECTIONS
The 3 Series Speakers are equipped with balanced XLR and 6 mm (¼") TRS inputs for connection to professional
computer audio interfaces, mixing consoles and audio production equipment as well as unbalanced consumer
audio products including personal music players, consumer audio receivers and audio visual equipment. Connect
professional equipment with balanced outputs to the XLR or 6 mm (¼") TRS input of the speaker using balanced
signal cables.
3-Series speakers are equipped with an INPUT SENSITIVITY SWITCH. The switch is set to the -10 dBV setting
when it ships from our factory. This setting will be best for many applications. However, you can set the switch
to the +4 dBu setting:
• When connecting 3 Series speakers to professional equipment with +4 dBu nominal output level, set
the INPUT SENSITIVITY SWITCH to the +4 dBu setting. To determine the nominal output level of the
connected equipment, consult the documentation supplied with the connected equipment.
• If you notice the sound is distorted, set this switch to the +4 dBu setting.
• When using the LSR310S in a system with the LSR308 or LSR305 studio monitors, set the INPUT
SENSITIVITY switch on the LSR305 or LSR308 to the -10dBV setting regardless of the LSR310S input
sensitivity switch setting.
LSR310S Subwoofer connections
The left and right outputs of the signal source should be connected directly to the LEFT and RIGHT INPUTS of the
subwoofer. The LEFT and RIGHT OUTPUTS of the subwoofer should be connected to the inputs of the left and
right speakers respectively.
POWER CONNECTIONS
The 3 Series speakers incorporate a universal power supply allowing these to be used domestically and
internationally. The ground terminal of the IEC plug is required by wiring codes and regulations and must
always be connected to the electrical installation safety ground.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAkING SOUND
After connections are made, reduce the output level of the audio source (mixing console, computer recording
system, or preamp) to minimum. Set the 3 Series POWER SWITCH to the “ON position.” After a short delay
the POWER INDICATOR on the front of each speaker will illuminate and the speakers will be ready to reproduce
audio signals. Power-on connected audio equipment, and slowly advance the volume control of connected
audio equipment to achieve a suitable listening level. Balance the subwoofer in the system using the rear panel
VOLUME CONTROL on each speaker. Additional balance of bass can be achieved by adjusting the placement
of the subwoofer in the room.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: LSR305 and LSR308 Powered Studio Monitors
Front View
Back View
1
3
2
6
4
5
7
8
9
FEATURES
1. HIGH FREQUENCY TRANSDUCER (Tweeter) – Reproduces high frequency signals.
2. WAVEGUIDE – The specially designed Image Control Waveguide enhances imaging and
optimizes the blend of direct and reflected sound in the room, ensuring neutral sound
at the mix position.
3. POWER INDICATOR - Illuminates when power is connected and the POWER SWITCH is set to ON.
Note after setting the power switch to ON, there is a short delay prior to illumination of the LED.
4. LOW FREQUENCY TRANSDUCER (Woofer) – Reproduces low frequency content of the input signal.
5. DUST DOME - Protects the inner circuit of the woofer. This self-repairing dust dome is resistant to
dents caused by fingers and objects.
6. LOW FREQUENCY PORT – The patented Slip Stream™ Port works in conjunction with the low
frequency transducer to provide accurate low frequency performance.
7. INPUT PANEL – Includes input connectors, power connector and user controls.
8. ENCLOSURE
9. PADS - Pads supplied with each monitor are user-installed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT PANEL
10. XLR INPUT – Connect professional equipment using an XLR connector.
11. 6 mm (¼") INPUT - Connect equipment using a 6 mm (¼") balanced or unbalanced connector.
12. INPUT SENSITIVITY SWITCH – Set this switch to +4 dBu to protect from overload when connecting to
professional equipment and sources with very high output.
13. LOW FREQUENCY TRIM – Allows boost or attenuation of low frequency output by 2 dB.
14. HIGH FREQUENCY TRIM – Allows boost or attenuation of high frequency output by 2 dB.
15. VOLUME CONTROL – Use this control to set the maximum listening level.
16. POWER RECEPTACLE – Connection for the power cord.
17. POWER SWITCH – Activates power for the system.
12
10
11
13
15
14
17
16
AUDIO CONNECTIONS
Connect signal sources to either the XLR or 6 mm (¼") INPUT CONNECTORS. Connect only a single signal
source to the speaker using either the XLR INPUT CONNECTOR, OR the 6 mm (¼") TRS INPUT CONNECTOR.
Do not connect multiple signal sources to both input connectors simultaneously.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: LSR310S Powered Studio Subwoofer
Front View
Back View
4
2
5
1
3
3
Bottom View
1
FEATURES
1. LOW FREQUENCY TRANSDUCER “WOOFER” – Reproduces low frequency signals.
2. POWER INDICATOR – Illuminates when power is connected and the Power Switch is set to ON.
3. FEET - Elevate the subwoofer to prevent acoustic coupling with the floor.
4. LOW FREQUENCY PORT – Works in conjunction with the low frequency transducer
to provide accurate low frequency performance.
5. INPUT PANEL - Includes input connectors, power connector and user controls.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT PANEL
6. RIGHT and LEFT XLR INPUTS
7. RIGHT and LEFT 6mm (1/4")
8. RIGHT and LEFT XLR OUTPUTS
9. INPUT SENSITIVITY switch – Set this switch to the +4 dBu setting when connecting professional equipment
and sources with very high output. NOTE: When the LSR310S is used in a system with LSR305 and LSR308,
set the INPUT SENSITIVITY switch on the LSR305 or LSR308 to the -10dBV setting regardless of the LSR310S
input sensitivity switch setting.
10. VOLUME CONTROL – Use this control to balance the volume of the subwoofer with the volume of the
speakers in the system.
11. CROSSOVER FREQUENCY – Three settings are provided: 80 Hz, XLF and External - The 80 Hz setting
is recommended for use with the LSR305, LSR308 and any studio monitors. The External setting allows use of
an outboard crossover. Select the XLF Extended Low Frequency setting to activate a circuit that emulates the
bass tuning commonly applied to playback systems in club environment.
12. POLARITY – Enables optional 180 degree reversal of the subwoofer output to optimize the blend of the
subwoofer with the main speakers according to relative positions of speakers and the listening position in the
room. Select the setting that produces the greatest amount of bass when heard at the listening position.
13. POWER RECEPTACLE – Connection for the power cord.
14. POWER SWITCH – Activates power for the subwoofer.
8
7
6
12
11
9
10
13
14
AUDIO CONNECTIONS
Connect signal sources to either the XLR or 6 mm (¼") INPUT CONNECTORS. Connect a single signal source to
the speaker using either the XLR INPUT CONNECTORs, OR the 6 mm (¼") TRS INPUT CONNECTORs. Do not
connect multiple signal sources to the XLR and 6 mm (1/4”) input connectors simultaneously. When using the
LSR310S in a Surround Sound System – if the LSR310S Subwoofer is being used to reproduce the .1 LFE channel
in a surround sound system, connect the .1 LFE signal to either the LEFT or RIGHT input of the subwoofer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE SUBWOOFER LEVEL
When the LSR310S Subwoofer is used in a system with LSR305 or LSR308 speakers, the ideal balance is
achieved when the position of the volume control on the subwoofer is set to the same position as the volume
control on the main speakers. Placement of the speakers in the room can affect the amount of bass heard at
the listening position.
If more or less subwoofer volume is desired, you may use the volume control on the subwoofer to achieve the
balance that works best for your application and taste.
PLACEMENT AND POLARITY SETTING
Because the human ear cannot easily recognize where low frequencies are originating (they are said to be
“non-directional”), subwoofer placement is not nearly as critical as main channel speaker positioning. The
LSR310S is designed to be placed directly on the floor and not elevated or mounted in any way. Set the
POLARITY switch to the setting that yields a stronger perceived bass response at the listening position.
In a stereo system, the subwoofer should optimally be placed between the two main speakers. In a surround
sound system, the subwoofer should be placed between the center and left channel speakers or the center
and right channel speakers. Precise central placement is not necessary. Centered positioning in the room can
sometimes cause unwanted cancellation, so it is recommended that the subwoofer be placed slightly off-
center and not at the midpoint between the left and right walls.
CROSSOVER SETTINGS AND “BASS MANAGEMENT”
“Bass management” is a term that refers to the practice of using a subwoofer to reproduce the bass frequencies
of the main channels. Because of the physiology of the human ear, low frequencies are largely
non-directional. Given an adequate listening distance, we can’t easily tell where bass signals are coming from.
Thus, it makes little or no difference to the listening experience whether the bass component in a sound comes
from the originating speaker (which may be off to your left or right, or even behind you) or from a dedicated
subwoofer which is better equipped – and better positioned in the room – to reproduce low frequencies than
even a full-range monitor. For that reason, you may want to use an LSR310S subwoofer to reproduce all the
bass frequencies in your system. If you are using an LSR310S Subwoofer in your system, bass management is
accomplished simply by routing your Left and Right mix channels to the Subwoofer inputs and then from the
subwoofer outputs to the Left and Right speakers. The frequency at which the subwoofer divides signals to
the sub and the left and right speakers can be set using the Crossover Frequency selector switch on the input
panel of the LSR310S Subwoofer. The 80Hz filter setting is recommended when the goal is a full range reference
monitor system that accurately portrays content below the cut-off of the main speakers. The 80 Hz crossover
provides a smooth transition and between the subwoofer and the main speakers, while optimizing the blend of
low frequency in the system, without audible localization of bass, creating the perception of a full range system
with no subwoofer.
To produce a smooth transition between the speakers and the subwoofer and the goal is an accurate
representation of frequency response in the program material. Two additional settings are provided:
XLF and External.
XLF
A trend in music production is the requirement for enhanced low frequency response in the control room.
Artists and producers involved in the production of dance music appreciate the ability to audition their work as it
might sound when played on a system with enhanced low frequency tuning, commonly employed in dance clubs.
A JBL first, the LSR310S includes a special XLF Extended Low Frequency setting that emulates the response
curve applied to a club playback system. When the XLF crossover setting is selected, a 120Hz High Pass Filter is
engaged in conjunction with a 10 dB boost at 60Hz with a bandwidth of 0.5 octaves. Using this setting, the bass
output more than doubles and the character of low frequency approximates that of a club system. Continuous
low frequency with very high peak SPL is made possible by JBL’s new long excursion low frequency driver
working in concert with JBL’s patented Slip Stream™ Port design, and powered by a 200 Watt class D amplifier.
A protective circuit allows the 310S to continuously produce low frequency at high output without failure.
In situations where positioning will allow, an additional 6 dB of output can be achieved by positioning the
LSR310S subwoofer adjacent to a wall or at the intersection of two walls.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
External
Select this setting when connecting the subwoofer to an external bass management system.
When external is selected, XLR left and right outputs are disabled.
SURROUND SOUND SYSTEMS AND LFE
The LSR310S Subwoofer can be used to reproduce the LFE (Low Frequency Effects) or .1 channel in a
surround sound system. In film production applications, the LFE channel contains low frequency effects,
such as the sounds of explosions, and other sounds with a strong low frequency component. In music
applications, the LFE channel usually contains low frequency instruments such as bass, bass drum, and
synthesizer elements.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: System Connections
TWO CHANNEL SYSTEMS
LEFT
RIGHT
CHANNEL SPEAKER
CHANNEL SPEAKER
SUBWOOFER
MIxER
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SURROUND SOUND SYSTEMS
LEFT
CENTER
SPEAKER
RIGHT
CHANNEL SPEAKER
CHANNEL SPEAKER
SUBWOOFER
COMPUTER
AUDIO INTERFACE
COMPUTER
AUDIO SYSTEM
LEFT
SURROUND SPEAKER
RIGHT
SURROUND SPEAKER
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Trouble Shooting
TROUBLE SHOOTING
If there is no sound from your speakers, check these settings:
• Make sure a signal source is connected and producing sound.
• Make sure the POWER INDICATOR is illuminated on the front of the speaker.
• Make sure the VOLUME CONTROL is not set to the full counter-clockwise minimum position.
• Confirm the power cable is connected and the POWER SWITCH is set to the ON position.
If the above measures do not correct the problem, please contact JBL Professional Customer Service.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Specifications
Specifications
LSR305
LSR308
LSR310S
Frequency Range: 43 Hz – 24 kHz
37 Hz - 24 kHz
27 Hz
Crossover: 1725 Hz 4th order acoustic
1800 Hz 4th order acoustic
Linkwitz-Riley
- - -
Linkwitz-Riley
Maximum Peak SPL: 108 dB SPL *
112 dB SPL *
113 dB **
Maximum Peak Input Level: +6 dBV / +20.3 dBu
+6 dBV / +20.3 dBu
+6 dBV / +20.3 dBu
-10 dBV / +4 dBu
Input Connectors: 1 x XLR, 1 x TRS Balanced
1 x XLR, 1 x TRS Balanced
92 dB / 1m
2 x XLR, 2 x TRS Balanced
92 dB / 1m
Input Sensitivity: 92 dB / 1m
(-10 dBV input)
HF Driver Size: 25 mm (1")
LF Driver Size: 127 mm (5")
25 mm (1")
203 mm (8")
56W Class D
- - -
250 mm (10")
HF Driver Power Amp: 41 W Class D
- - -
LF Driver Power Amp: 41 W Class D
56W Class D
200W Class D
HF Trim Control: +2 dB, 0, -2 dB @ 4.4 kHz
LF Trim Control: +2 dB, 0, -2 dB @ 115 Hz
AC Input Voltage: 100-240 VAC +/- 10% 50/60 Hz
Enclosure Construction: 15 mm (5/8 in) MDF
+2 dB, 0, -2 dB @ 4.4 kHz
+2 dB, 0, -2 dB @ 115 Hz
100-240 VAC +/- 10% 50/60 Hz
15 mm (5/8 in) MDF
- - -
- - -
100-240 VAC +/- 10% 50/60 Hz
18 mm (3/4 in) MDF
Enclosure Finish: Matte Black PVC
Matte Black PVC
Matte Black PVC
Baffle Construction: Injection-molded structural ABS
Baffle Finish:d Metallic Black Acrylic Paint
Injection-molded structural ABS
Metallic Black Acrylic Paint
- - -
- - -
Dimensions (H x W x D): 298 mm x 185 mm x 231 mm
419 mm x 254 mm x 308 mm
(16.5 in x 10.0 in x 12.1 in)
448 mm x 381 mm x 398 mm
(17.65 in x 15.0 in x 15.65 in)
(11.75 in x 7.28 in x 9.88 in)
Weight: 4.6 kg (10.12 lbs)
8.6 kg (18.9 lbs)
15.6 kg (34.3 lbs)
Display Carton (H x W x D): 354 mm x 244 mm x 299 mm
473 mm x 312 mm x 358 mm
(18.6 in x 12.2 in x 14.0 in)
505 mm x 466 mm x 476 mm
(19.9 in x 18.3 in x 18.7 in)
(13.93 in x 9.6 in x 11.77 in)
Shipping Carton (H x W x D): 373 mm x 260 mm x 315 mm
491mm x 326 mm x 371 mm
(19.3 in x 12.8 in x 14.6 in)
520 mm x 478 mm x 488 mm
(20.5 in x 18.8 in x 19.2 in)
(14.69 in x 10.22 in x 12.4 in)
Shipping Weight: 6 kg (13.2 lbs)
10 kg (22 lbs)
19.1 kg (42 lbs)
* Full Bandwidth Pink Noise Measured C-Weighted
** Measured in Half Space
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 9: JBL Service Contact Information
MAILING ADDRESS:
JBL Professional
8500 Balboa Blvd.
Northridge, CA 91329
SHIPPING ADDRESS:
JBL Professional
8500 Balboa Blvd., Dock 15
Northridge, CA 91329
(Do not return product to this address without first obtaining prior authorization from JBL)
CUSTOMER SERVICE:
Monday through Friday
8:00am - 5:00pm
Pacific Coast Time in the U.S.A.
(800) 8JBLPRO (800.852.5776)
PRODUCT REGISTRATION:
On The World Wide Web:
PROFESSIONAL CONTACTS, OUTSIDE THE USA:
Contact the JBL Professional Distributor in your area. A complete list of JBL Professional international
EN DEHORS DES ETATS-UNIS:
Contacter votre Distributeur JBL Professional. Une liste complète de nos distributeurs internationaux est
INTERNATIONAL:
Wenden Sie sich an Ihre örtliche JBL Professional Vertretung. Eine vollständige Liste der internationalen
FUERA DE LOS ESTADOS UNIDOS:
encontrará una lista completa de los distribuidores de JBL International.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 10: Product Warranty Information
The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for
five years from the date of the first consumer purchase. JBL amplifiers are warranted for three years from the date of
original purchase. Enclosures and all other JBL products are warranted for two years from the date of
original purchase.
WHO IS PROTECTED BY THIS WARRANTY?
Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product has
been purchased in the Continental United States, Hawaii or Alaska. (This Warranty does not apply to JBL products
purchased elsewhere except for purchases by military outlets. Other purchasers should contact the local JBL
distributor for warranty information.); and B.) The original dated bill of sale is presented whenever warranty service
is required.
WHAT DOES THE JBL WARRANTY COVER?
Except as specified below, your JBL Warranty covers all defects in material and workmanship. The following
are not covered: Damage caused by accident, misuse, abuse, product modification or neglect; damage occurring
during shipment; damage resulting from failure to follow instructions contained in your Instruction Manual;
damage resulting from the performance of repairs by someone not authorized by JBL; claims based upon any
misrepresentations by the seller; any JBL product on which the serial number has been defaced, modified
or removed.
WHO PAYS FOR WHAT?
JBL will pay all labor and material expenses for all repairs covered by this warranty. Please be sure to save the
original shipping cartons because a charge will be made if replacement cartons are requested. Payment of shipping
charges is discussed in the next section of this warranty.
HOW TO OBTAIN WARRANTY PERFORMANCE
If your JBL product ever needs service, write or telephone us at JBL Incorporated (Attn: Customer Service
Department), 8500 Balboa Boulevard, PO. Box 2200, Northridge, California 91329 (818/893-8411). We may direct
you to an authorized JBL Service Agency or ask you to send your unit to the factory for repair. Either way, you’ll
need to present the original bill of sale to establish the date of purchase. Please do not ship your JBL product to
the factory without prior authorization. If transportation of your JBL product presents any unusual difficulties, please
advise us and we may make special arrangements with you. Otherwise, you are responsible for transporting your
product for repair or arranging for its transportation and for payment of any initial shipping charges. However, we
will pay the return shipping charges if repairs are covered by the warranty.
LIMITATION OF IMPLIED WARRANTIES
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
EXCLUSION OF CERTAIN DAMAGES
JBL’S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE
PRODUCT AND SHALL NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT
ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY, FROM STATE TO STATE.
JBL Professional
8500 Balboa Boulevard
Northridge, CA 91329 USA
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number:
Rev 5041835A
Download from Www.Somanuals.com. All Manuals Search And Download.
|